Error and System Messages System Message Guide for Cisco IOS XE Cupertino 17.8.x Save Download Print Updated:May 8, 2022 Bias-Free Language Contents System Message Guide for Cisco IOS XE Cupertino 17.8.x Cisco System Messages Overview How To Read System Error Messages Error Message Traceback Reports System and Error Messages in Cisco IOS XE Cupertino 17.8.x Additional References System Message Guide for Cisco IOS XE Cupertino 17.8.x Cisco System Messages Overview This document describes system messages for Cisco software releases. During operation, the system software sends these messages to the console (and, optionally, to a logging server on another system) during operation. Not all system messages indicate problems with your system. Some are purely informational, and others may help diagnose problems with communications lines, internal hardware, or the system software. How To Read System Error Messages System error messages begin with a percent sign (%) and are structured as follows:%FACILITY-SUBFACILITY-SEVERITY-MNEMONIC: Message-text FACILITY is a code consisting of two or more uppercase letters that indicate the facility to which the message refers. A facility can be a hardware device, a protocol, or a module of the system software. SEVERITY is a single-digit code from 0 to 7 that reflects the severity of the condition. The lower the number, the more serious the situation. Table 1 lists the severity levels. MNEMONIC is a code that uniquely identifies the error message. Message-text is a text string describing the condition. This portion of the message sometimes contains detailed information about the event, including terminal port numbers, network addresses, or addresses that correspond to locations in the system memory address space. Because the information in these variable fields changes from message to message, it is represented here by short strings enclosed in square brackets ([ ]). A decimal number, for example, is represented as [dec]. Table 2 lists the representations of variable fields and the type of information in them. The following is a sample system error message: %LINK-2-BADVCALL: Interface [chars], undefined entry point Some error messages also indicate the card and slot reporting the error. These error messages begin with a percent sign (%) and are structured as follows: %CARD-SEVERITY-MSG:SLOT %FACILITY-SEVERITY-MNEMONIC: Message-text CARD is a code that describes the type of card reporting the error. VIP and FEIP are possible card types. MSG is a mnemonic that indicates that this is a message. It is always shown as MSG. SLOT indicates the slot number of the card reporting the error. It is shown as SLOT followed by a number (for example, SLOT5). The prepended portion of the error message (%CARD-SEVERITY-MSG:SLOT) is not shown in the error message listings in this document. Error Message Severity Levels Error message severity levels correspond to the keywords assigned by the logging global configuration commands that define where and at what level these messages appear. The default is to log messages to the console at the debugging level (7). For more information, see the system configuration chapter and descriptions of the logging command in the configuration guide and command reference. Level Description 0 - emergency System unusable 1 - alert Immediate action needed 2 - critical Critical condition 3 - error Error condition 4 - warning Warning condition 5 - notification Normal, but significant, condition 6 - informational Informational message only 7 - debugging Appears during debugging only Representation of Variable Fields in Error Messages Representation Type of Information [atalk_address] AppleTalk address [atalk_net] AppleTalk network, either 600 or 600-601 [char] Single character [chars] Character string [dec] Decimal number [enet] Ethernet address (for example, 0000.FEED.00C0) [hex] Hexadecimal number [inet] Internet address (for example, 10.0.2.16) [int] Integer number [node] Address or node name [sci_notation] Scientific notation [t-line] Terminal line number in octal (or decimal if the decimal-TTY service is enabled) [v-name] VINES name; or number (hex or decimal) Error Message Traceback Reports Some messages describe internal errors and contain traceback information. This information is very important and should be included when you report a problem to your technical support representative. The following sample message includes traceback information: -Process= "Exec", level= 0, pid= 17 -Traceback= 1A82 1AB4 6378 A072 1054 1860 System and Error Messages in Cisco IOS XE Cupertino 17.8.x Facility-Severity-Mnemonic Severity-Meaning Message Message-Explanation Component Recommended-Action - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 5-Notice 0 - - - - 5-Notice - A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table. SISF_COMP_NAME - - 5-Notice - - ipv6 "A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests" - 5-Notice - Two devices with random MACs generated the same MAC address. \n\ The second device has been rejected. SISF_COMP_NAME "The second device will need to regenerate its random MAC." - 6-Information authentication packet received on sessions with invalid config authentication only supported for multihop BFD sessions bfd LOG_STD_ACTION - 6-Information packet received failed authentication packet authentication failed bfd LOG_STD_ACTION - 6-Information Could not allocate valid session handle session handle not allocated bfd LOG_STD_ACTION - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 5-Notice fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 5-Notice fmt \extern const struct message_ msg_ ## fac ## _ ## name - - - - 3-Error fmt { \ size_t len = strlen - - - - 3-Error fmt { \ size_t len = strlen - - - - 3-Error fmt printf - - - - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 3-Error fmt \ syslog_ - - - - 3-Error \ fmt - - - - 3-Error - BULKSTAT Service Enabled SRVNAME_BULKSTAT SYSLOGDOC_NO_ACTION - 3-Error - BULKSTAT Service Disabled SRVNAME_BULKSTAT SYSLOGDOC_NO_ACTION - 3-Error - DCM_CORE Service nabled SRVNAME_DCM_CORE SYSLOGDOC_NO_ACTION - 3-Error - DCM_CORE Service Disabled SRVNAME_DCM_CORE SYSLOGDOC_NO_ACTION - 3-Error - DCM_CLI_DP Service nabled SRVNAME_DCM_CLI_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_CLI_DP Service Disabled SRVNAME_DCM_CLI_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_SNMP_DP Service nabled SRVNAME_DCM_SNMP_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_SNMP_DP Service Disabled SRVNAME_DCM_SNMP_DP SYSLOGDOC_NO_ACTION - 3-Error fmt \local_errmsg_t msg_ ## fac ## _ ## name = { #name - - - - 3-Error fmt \extern C local_errmsg_t msg_ ## fac ## _ ## name - - - - 6-Information authentication packet received on sessions with invalid config authentication only supported for multihop BFD sessions bfd LOG_STD_ACTION - 6-Information packet received failed authentication packet authentication failed bfd LOG_STD_ACTION - 6-Information Could not allocate valid session handle session handle not allocated bfd LOG_STD_ACTION - 5-Notice fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 5-Notice fmt \extern const struct message_ msg_ ## fac ## _ ## name - - - - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 3-Error fmt \ syslog_ - - - - 3-Error \ fmt - - - - 3-Error - BULKSTAT Service Enabled SRVNAME_BULKSTAT SYSLOGDOC_NO_ACTION - 3-Error - BULKSTAT Service Disabled SRVNAME_BULKSTAT SYSLOGDOC_NO_ACTION - 3-Error - DCM_CORE Service nabled SRVNAME_DCM_CORE SYSLOGDOC_NO_ACTION - 3-Error - DCM_CORE Service Disabled SRVNAME_DCM_CORE SYSLOGDOC_NO_ACTION - 3-Error - DCM_CLI_DP Service nabled SRVNAME_DCM_CLI_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_CLI_DP Service Disabled SRVNAME_DCM_CLI_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_SNMP_DP Service nabled SRVNAME_DCM_SNMP_DP SYSLOGDOC_NO_ACTION - 3-Error - DCM_SNMP_DP Service Disabled SRVNAME_DCM_SNMP_DP SYSLOGDOC_NO_ACTION - 3-Error 0 - - - - 3-Error - A data packet notification has been received because a snooping policy with the data glean option is configured and the Source address of the packet is not currently in the Binding Table. SISF_COMP_NAME - - 3-Error - - ipv6 "A low rate of vetoed resolutions is not serious. \n\ If there is a high rate of vetos this might suggest that \n\ the link is under attack. Investigate the source of the \n\ packets driving these resolution requests" - 3-Error - Two devices with random MACs generated the same MAC address. \n\ The second device has been rejected. SISF_COMP_NAME "The second device will need to regenerate its random MAC." - 3-Error fmt { \ size_t len = strlen - - - - 3-Error fmt { \ size_t len = strlen - - - - 3-Error fmt printf - - - - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 5-Notice fmt \local_errmsg_t msg_ ## fac ## _ ## name = { #name - - - - 5-Notice fmt \extern C local_errmsg_t msg_ ## fac ## _ ## name - - - - 4-Warning fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - - - - - - - 4-Warning fmt \extern const struct message_ msg_ ## fac ## _ ## name - - - - 4-Warning fmt \static message_stats_ptr fac ## _ ## name ## _stat_redir_ptr __crb_sysrgn - - - - 4-Warning fmt - - - - 4-Warning fmt - - - - 3-Error fmt \static message_stats * fac ## _ ## name ## _stat_redir_ptr - - - - 3-Error fmt \extern const struct message_ msg_ ## fac ## _ ## name - - - _NEW_APP_NAME_-3-MSG_ERR 3-Error [chars] Error Messages pagent "try debug command" _NEW_APP_NAME_-6-MSG_INF 6-Information [chars] Program information - - _NEW_APP_NAME_-7-MSG_DBG 7-Debug [chars] Debug Messages - - AAA_CACHE-3-NULL_TREE_PERIODIC_PROC 3-Error Cache Tree pointer is of null value The cache tree pointer is of null value. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAA_CACHE-3-NULL_TREE_PERIODIC_PROC 3-Error Cache Tree pointer is of null value The cache tree pointer is of null value. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAA-2-AAAMULTILINKERROR 2-Critical [chars]%08X: Acct db for Id %08X absent AAA internal error aaa LOG_STD_ACTION AAA-2-AAAMULTILINKERROR 2-Critical [chars]%08X: Acct db for Id %08X absent AAA internal error aaa LOG_STD_ACTION AAA-2-AAAMULTILINKERROR 2-Critical [chars]%08X: Acct db for Id %08X absent AAA internal error aaa LOG_STD_ACTION AAA-2-AAAMULTILINKERROR 2-Critical [chars]%08X: Acct db for Id %08X absent AAA internal error aaa LOG_STD_ACTION AAA-2-FORKFAIL 2-Critical Cannot fork process [chars] Attempted to fork a process and failed. The reason could be either hardware or software. aaa LOG_STD_ACTION AAA-2-FORKFAIL 2-Critical Cannot fork process [chars] Attempted to fork a process and failed. The reason could be either hardware or software. aaa LOG_STD_ACTION AAA-2-FORKFAIL 2-Critical Cannot fork process [chars] Attempted to fork a process and failed. The reason could be either hardware or software. aaa LOG_STD_ACTION AAA-2-FORKFAIL 2-Critical Cannot fork process [chars] Attempted to fork a process and failed. The reason could be either hardware or software. aaa LOG_STD_ACTION AAA-3-ACCT_IOMEM_LOW 3-Error AAA ACCT process suspended : low I/O memory AAA ACCT process has been suspended due to insufficient IO memory. aaa LOG_STD_ACTION AAA-3-ACCT_IOMEM_LOW 3-Error AAA ACCT process suspended : low I/O memory AAA ACCT process has been suspended due to insufficient IO memory. aaa LOG_STD_ACTION AAA-3-ACCT_IOMEM_LOW 3-Error AAA ACCT process suspended : low I/O memory AAA ACCT process has been suspended due to insufficient IO memory. aaa LOG_STD_ACTION AAA-3-ACCT_IOMEM_LOW 3-Error AAA ACCT process suspended : low I/O memory AAA ACCT process has been suspended due to insufficient IO memory. aaa LOG_STD_ACTION AAA-3-ACCT_LOW_IO_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_IO_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_IO_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_IO_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient I/O memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough I/O memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_MEM_UID_FAIL 3-Error AAA unable to create UID for incoming calls due to insufficient processor memory Stop creating the AAA UID due to LOW processor memory aaa LOG_STD_ACTION AAA-3-ACCT_LOW_MEM_UID_FAIL 3-Error AAA unable to create UID for incoming calls due to insufficient processor memory Stop creating the AAA UID due to LOW processor memory aaa LOG_STD_ACTION AAA-3-ACCT_LOW_MEM_UID_FAIL 3-Error AAA unable to create UID for incoming calls due to insufficient processor memory Stop creating the AAA UID due to LOW processor memory aaa LOG_STD_ACTION AAA-3-ACCT_LOW_MEM_UID_FAIL 3-Error AAA unable to create UID for incoming calls due to insufficient processor memory Stop creating the AAA UID due to LOW processor memory aaa LOG_STD_ACTION AAA-3-ACCT_LOW_PROC_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_PROC_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_PROC_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_LOW_PROC_MEM_TRASH 3-Error AAA unable to handle accounting requests due to insufficient processor memory and could be trashing the queued accounting records Dropping the accounting request as there is no enough processor memory. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_UNKNOWN_REASON_TRASH 3-Error AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_UNKNOWN_REASON_TRASH 3-Error AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_UNKNOWN_REASON_TRASH 3-Error AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ACCT_UNKNOWN_REASON_TRASH 3-Error AAA unable to handle accounting requests reason unknown and could be trashing the queued accounting records Dropping the accounting request reason unknown. Hence all queued accounting requests shall be trashed aaa LOG_STD_ACTION AAA-3-ATTRFORMATERR 3-Error Attribute with unknown format [dec] An attribute was found with an invalid format. aaa "Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-ATTRFORMATERR 3-Error Attribute with unknown format [dec] An attribute was found with an invalid format. aaa "Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-ATTRFORMATERR 3-Error Attribute with unknown format [dec] An attribute was found with an invalid format. aaa "Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-ATTRFORMATERR 3-Error Attribute with unknown format [dec] An attribute was found with an invalid format. aaa "Attribute with unknown format in definition. Enable AAA " "debug and try to replicate the steps to get the message. " "If the meassage appears again Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-AUTH_LOW_IOMEM 3-Error RADIUS process is unable to handle the requests due to insufficient I/O memory RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure. aaa LOG_STD_ACTION AAA-3-AUTH_LOW_IOMEM 3-Error RADIUS process is unable to handle the requests due to insufficient I/O memory RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure. aaa LOG_STD_ACTION AAA-3-AUTH_LOW_IOMEM 3-Error RADIUS process is unable to handle the requests due to insufficient I/O memory RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure. aaa LOG_STD_ACTION AAA-3-AUTH_LOW_IOMEM 3-Error RADIUS process is unable to handle the requests due to insufficient I/O memory RADIUS process unable to handle request due to insufficient IO memory. Hence returning failure. aaa LOG_STD_ACTION AAA-3-AUTHORMLISTUNDEF 3-Error Authorization method list '[chars]' is not defined. Please define it. A given method list was listed in a command without defining it first. The method list should be defined before use. aaa "Define the method list before using it." AAA-3-AUTHORMLISTUNDEF 3-Error Authorization method list '[chars]' is not defined. Please define it. A given method list was listed in a command without defining it first. The method list should be defined before use. aaa "Define the method list before using it." AAA-3-AUTHORMLISTUNDEF 3-Error Authorization method list '[chars]' is not defined. Please define it. A given method list was listed in a command without defining it first. The method list should be defined before use. aaa "Define the method list before using it." AAA-3-AUTHORMLISTUNDEF 3-Error Authorization method list '[chars]' is not defined. Please define it. A given method list was listed in a command without defining it first. The method list should be defined before use. aaa "Define the method list before using it." AAA-3-BADCURSOR 3-Error invalid cursor index [dec] max [dec] service [chars] protocol [chars] A AAA client has provided an invalid attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-BADCURSOR 3-Error invalid cursor index [dec] max [dec] service [chars] protocol [chars] A AAA client has provided an invalid attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-BADCURSOR 3-Error invalid cursor index [dec] max [dec] service [chars] protocol [chars] A AAA client has provided an invalid attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-BADCURSOR 3-Error invalid cursor index [dec] max [dec] service [chars] protocol [chars] A AAA client has provided an invalid attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-BADLIST 3-Error invalid list AAA ID [dec] A AAA client has provided an invalid attribute list to AAA. aaa LOG_STD_ACTION AAA-3-BADLIST 3-Error invalid list AAA ID [dec] A AAA client has provided an invalid attribute list to AAA. aaa LOG_STD_ACTION AAA-3-BADLIST 3-Error invalid list AAA ID [dec] A AAA client has provided an invalid attribute list to AAA. aaa LOG_STD_ACTION AAA-3-BADLIST 3-Error invalid list AAA ID [dec] A AAA client has provided an invalid attribute list to AAA. aaa LOG_STD_ACTION AAA-3-BADMAGIC 3-Error Data structure failed magic number sanity check A corrupted data structure has been found which was stored internally. aaa LOG_STD_ACTION AAA-3-BADMAGIC 3-Error Data structure failed magic number sanity check A corrupted data structure has been found which was stored internally. aaa LOG_STD_ACTION AAA-3-BADMAGIC 3-Error Data structure failed magic number sanity check A corrupted data structure has been found which was stored internally. aaa LOG_STD_ACTION AAA-3-BADMAGIC 3-Error Data structure failed magic number sanity check A corrupted data structure has been found which was stored internally. aaa LOG_STD_ACTION AAA-3-BADMETHOD 3-Error Cannot process [chars] method [dec] A method list function encountered a method list that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHOD 3-Error Cannot process [chars] method [dec] A method list function encountered a method list that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHOD 3-Error Cannot process [chars] method [dec] A method list function encountered a method list that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHOD 3-Error Cannot process [chars] method [dec] A method list function encountered a method list that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHODERROR 3-Error Cannot process [chars] method [chars] A method list function encountered a method type that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHODERROR 3-Error Cannot process [chars] method [chars] A method list function encountered a method type that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHODERROR 3-Error Cannot process [chars] method [chars] A method list function encountered a method type that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADMETHODERROR 3-Error Cannot process [chars] method [chars] A method list function encountered a method type that was unknown or could not be handled. aaa LOG_STD_ACTION AAA-3-BADSERVERTYPEERROR 3-Error Cannot process [chars] server type [chars] A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration. aaa "Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION AAA-3-BADSERVERTYPEERROR 3-Error Cannot process [chars] server type [chars] A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration. aaa "Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION AAA-3-BADSERVERTYPEERROR 3-Error Cannot process [chars] server type [chars] A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration. aaa "Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION AAA-3-BADSERVERTYPEERROR 3-Error Cannot process [chars] server type [chars] A method list function encountered a server type that was unknown or could not be handled. This may be due to a server misconfiguration. aaa "Research the cause of the misconfiguration and " "attempt to correct it otherwise take the following " "action. "LOG_STD_ACTION AAA-3-BUFFER_OVERFLOW 3-Error Radius I/O buffer has overflowed An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-BUFFER_OVERFLOW 3-Error Radius I/O buffer has overflowed An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-BUFFER_OVERFLOW 3-Error Radius I/O buffer has overflowed An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-BUFFER_OVERFLOW 3-Error Radius I/O buffer has overflowed An unusually large number of RADIUS attributes has caused AAA to overflow its RADIUS I/O buffer. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-DROPACCTFAIL 3-Error Accounting record dropped send to server failed: [chars] An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly. aaa "Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter show running-" "config command contact your cisco technical " "support representative and provide all the information " "gathered to the representative." AAA-3-DROPACCTFAIL 3-Error Accounting record dropped send to server failed: [chars] An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly. aaa "Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter show running-" "config command contact your cisco technical " "support representative and provide all the information " "gathered to the representative." AAA-3-DROPACCTFAIL 3-Error Accounting record dropped send to server failed: [chars] An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly. aaa "Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter show running-" "config command contact your cisco technical " "support representative and provide all the information " "gathered to the representative." AAA-3-DROPACCTFAIL 3-Error Accounting record dropped send to server failed: [chars] An attempt to send an accounting record to a server failed. This happens when device exhaust all its retries and retransmission. The cause for this be the servers may not be operational or the NAS is not configured properly. aaa "Check the server whether they are " "operational or not. Next check whether " "the device is configured properly. Refer to" "the server configuration section of the " "cisco IOS documentation. Finally check " "that the NAS can communicate with the server. " "If the problem persist Enter show running-" "config command contact your cisco technical " "support representative and provide all the information " "gathered to the representative." AAA-3-HA_INIT_FAILURE 3-Error High availability initialization failure: [chars] The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INIT_FAILURE 3-Error High availability initialization failure: [chars] The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INIT_FAILURE 3-Error High availability initialization failure: [chars] The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INIT_FAILURE 3-Error High availability initialization failure: [chars] The AAA subsystem was unable to perform necessary high-availability related initialization. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem will be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INTERNAL_ERROR 3-Error High availability internal error for unique id 0x%8x: [chars] The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INTERNAL_ERROR 3-Error High availability internal error for unique id 0x%8x: [chars] The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INTERNAL_ERROR 3-Error High availability internal error for unique id 0x%8x: [chars] The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-HA_INTERNAL_ERROR 3-Error High availability internal error for unique id 0x%8x: [chars] The AAA subsystem was suffered an internal error. In the event of switchover to a standby device sessions depending on high availability capabilities in the AAA subsystem may be forced to renegotiate. aaa LOG_STD_ACTION AAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAA-3-INVALIDPARM 3-Error invalid parameter was used when accessing AAA function A AAA client tried to use a AAA function with an invalid parameter. aaa LOG_STD_ACTION AAA-3-INVALIDPARM 3-Error invalid parameter was used when accessing AAA function A AAA client tried to use a AAA function with an invalid parameter. aaa LOG_STD_ACTION AAA-3-INVALIDPARM 3-Error invalid parameter was used when accessing AAA function A AAA client tried to use a AAA function with an invalid parameter. aaa LOG_STD_ACTION AAA-3-INVALIDPARM 3-Error invalid parameter was used when accessing AAA function A AAA client tried to use a AAA function with an invalid parameter. aaa LOG_STD_ACTION AAA-3-IPILLEGALMSG 3-Error Invalid use of ip_pid[dec] This error means a process sent an illegal message. - "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-IPILLEGALMSG 3-Error Invalid use of ip_pid[dec] This error means a process sent an illegal message. - "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-IPILLEGALMSG 3-Error Invalid use of ip_pid[dec] This error means a process sent an illegal message. - "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-IPILLEGALMSG 3-Error Invalid use of ip_pid[dec] This error means a process sent an illegal message. - "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-ISDNINTF 3-Error [chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\ Configuration can not be applied to individual ISDN channels. aaa "You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide." AAA-3-ISDNINTF 3-Error [chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\ Configuration can not be applied to individual ISDN channels. aaa "You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide." AAA-3-ISDNINTF 3-Error [chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\ Configuration can not be applied to individual ISDN channels. aaa "You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide." AAA-3-ISDNINTF 3-Error [chars] [chars]: Can not apply configuration to ISDN channel:\n \[chars]\ Configuration can not be applied to individual ISDN channels. aaa "You need virtual-profiles and virtual-access " "interfaces to apply configuration to ISDN. " "Refer to the section on \"Configuring virtual " "profile by AAA Configuration\" in the Cisco IOS " "Dial Technologies Configuration Guide." AAA-3-LOW_MEM 3-Error [chars] process is unable to handle the incoming packet due to low memory Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory. aaa LOG_STD_ACTION AAA-3-LOW_MEM 3-Error [chars] process is unable to handle the incoming packet due to low memory Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory. aaa LOG_STD_ACTION AAA-3-LOW_MEM 3-Error [chars] process is unable to handle the incoming packet due to low memory Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory. aaa LOG_STD_ACTION AAA-3-LOW_MEM 3-Error [chars] process is unable to handle the incoming packet due to low memory Please check the processor memory or IO memory. Most likely one is them has less available memory or worst case both may have insufficient memory. aaa LOG_STD_ACTION AAA-3-MLIST_INTERNAL_ERROR 3-Error method list '[chars]': [chars] This is an internal software error. aaa LOG_STD_ACTION AAA-3-MLIST_INTERNAL_ERROR 3-Error method list '[chars]': [chars] This is an internal software error. aaa LOG_STD_ACTION AAA-3-MLIST_INTERNAL_ERROR 3-Error method list '[chars]': [chars] This is an internal software error. aaa LOG_STD_ACTION AAA-3-MLIST_INTERNAL_ERROR 3-Error method list '[chars]': [chars] This is an internal software error. aaa LOG_STD_ACTION AAA-3-MLIST_TOO_MANY_METHODS 3-Error method list '[chars]' This is an internal software error. An AAA client attempted to add too many methods to a method list. aaa "This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative." AAA-3-MLIST_TOO_MANY_METHODS 3-Error method list '[chars]' This is an internal software error. An AAA client attempted to add too many methods to a method list. aaa "This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative." AAA-3-MLIST_TOO_MANY_METHODS 3-Error method list '[chars]' This is an internal software error. An AAA client attempted to add too many methods to a method list. aaa "This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative." AAA-3-MLIST_TOO_MANY_METHODS 3-Error method list '[chars]' This is an internal software error. An AAA client attempted to add too many methods to a method list. aaa "This is an internal software error. Check bug tool-kit " "on Cisco web-site for the issue. If you didn't find one " "Collect the error message and report it to your " "technical support representative." AAA-3-NOTABLE 3-Error AAA ID [dec] Resource failure. aaa LOG_STD_ACTION AAA-3-NOTABLE 3-Error AAA ID [dec] Resource failure. aaa LOG_STD_ACTION AAA-3-NOTABLE 3-Error AAA ID [dec] Resource failure. aaa LOG_STD_ACTION AAA-3-NOTABLE 3-Error AAA ID [dec] Resource failure. aaa LOG_STD_ACTION AAA-3-NULLCURSOR 3-Error Null cursor A AAA client has provided a nonexistent attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-NULLCURSOR 3-Error Null cursor A AAA client has provided a nonexistent attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-NULLCURSOR 3-Error Null cursor A AAA client has provided a nonexistent attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-NULLCURSOR 3-Error Null cursor A AAA client has provided a nonexistent attribute cursor to AAA. aaa LOG_STD_ACTION AAA-3-NULLVRF 3-Error Null vrf entry A NULL VRF entry found while comparing the AAA VRF attributes. aaa LOG_STD_ACTION AAA-3-NULLVRF 3-Error Null vrf entry A NULL VRF entry found while comparing the AAA VRF attributes. aaa LOG_STD_ACTION AAA-3-NULLVRF 3-Error Null vrf entry A NULL VRF entry found while comparing the AAA VRF attributes. aaa LOG_STD_ACTION AAA-3-NULLVRF 3-Error Null vrf entry A NULL VRF entry found while comparing the AAA VRF attributes. aaa LOG_STD_ACTION AAA-3-PARSEERR 3-Error Error[dec] parser is unable to parse [chars] per-user command All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error. parser and aaa "The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative." AAA-3-PARSEERR 3-Error Error[dec] parser is unable to parse [chars] per-user command All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error. parser and aaa "The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative." AAA-3-PARSEERR 3-Error Error[dec] parser is unable to parse [chars] per-user command All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error. parser and aaa "The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative." AAA-3-PARSEERR 3-Error Error[dec] parser is unable to parse [chars] per-user command All attempts to parse this per_user unconfigure command failed. The unconfigure command is called when an error occurs while configuring per-user commands to revert back. The unconfiguration may fail due to parser or AAA error. parser and aaa "The given unconfigure command was not executed. " "Switch on the debug peruser command and repeat " "the steps that caused the error. If you get the error " "Report it to your technical support representative." AAA-3-PASSWDRESTRICTERR 3-Error AAA password restriction failed.- [chars]\n The password/secret/key entered is not meeting the password restrictions configured aaa LOG_STD_ACTION AAA-3-PASSWDRESTRICTERR 3-Error AAA password restriction failed.- [chars]\n The password/secret/key entered is not meeting the password restrictions configured aaa LOG_STD_ACTION AAA-3-PASSWDRESTRICTERR 3-Error AAA password restriction failed.- [chars]\n The password/secret/key entered is not meeting the password restrictions configured aaa LOG_STD_ACTION AAA-3-PASSWDRESTRICTERR 3-Error AAA password restriction failed.- [chars]\n The password/secret/key entered is not meeting the password restrictions configured aaa LOG_STD_ACTION AAA-3-SERVER_INTERNAL_ERROR 3-Error Server '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SERVER_INTERNAL_ERROR 3-Error Server '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SERVER_INTERNAL_ERROR 3-Error Server '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SERVER_INTERNAL_ERROR 3-Error Server '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SG_DEADTIME_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter Show tech-support " "command collect all the information and error " "message and report it to your technical support " "representative." AAA-3-SG_DEADTIME_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter Show tech-support " "command collect all the information and error " "message and report it to your technical support " "representative." AAA-3-SG_DEADTIME_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter Show tech-support " "command collect all the information and error " "message and report it to your technical support " "representative." AAA-3-SG_DEADTIME_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find " "one Enter Show tech-support " "command collect all the information and error " "message and report it to your technical support " "representative." AAA-3-SG_INTERNAL_ERROR 3-Error server group '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter Show tech-support" " command collect all the information " "and error message report it to your technical " "support representative." AAA-3-SG_INTERNAL_ERROR 3-Error server group '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter Show tech-support" " command collect all the information " "and error message report it to your technical " "support representative." AAA-3-SG_INTERNAL_ERROR 3-Error server group '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter Show tech-support" " command collect all the information " "and error message report it to your technical " "support representative." AAA-3-SG_INTERNAL_ERROR 3-Error server group '[chars]': [chars] This is an internal software error in the AAA server group subsystem. aaa "This is an internal software error. Check bug " "toolkit on Cisco website for the issue. If you " "didn't find one Enter Show tech-support" " command collect all the information " "and error message report it to your technical " "support representative." AAA-3-SG_TESTPROC_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SG_TESTPROC_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SG_TESTPROC_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SG_TESTPROC_FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs. Check bug toolkit " "on Cisco website for the issue. If you didn't find one " "Enter Show tech-support command " "Collect all the information and error message and report " "it to your technical support representative." AAA-3-SORTFAIL 3-Error [chars] :Peruser Could not sort the [chars] attributes Sorting of the attributes received from AAA server failed. aaa LOG_STD_ACTION AAA-3-SORTFAIL 3-Error [chars] :Peruser Could not sort the [chars] attributes Sorting of the attributes received from AAA server failed. aaa LOG_STD_ACTION AAA-3-SORTFAIL 3-Error [chars] :Peruser Could not sort the [chars] attributes Sorting of the attributes received from AAA server failed. aaa LOG_STD_ACTION AAA-3-SORTFAIL 3-Error [chars] :Peruser Could not sort the [chars] attributes Sorting of the attributes received from AAA server failed. aaa LOG_STD_ACTION AAA-5-LOCAL_USER_BLOCKED 5-Notice User [chars] blocked for login till [chars] User blocked since the number of authentication failures in the watch time exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-LOCAL_USER_BLOCKED 5-Notice User [chars] blocked for login till [chars] User blocked since the number of authentication failures in the watch time exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-USER_LOCKED 5-Notice User [chars] locked out on authentication failure User locked out since the number of authentication failures exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-USER_LOCKED 5-Notice User [chars] locked out on authentication failure User locked out since the number of authentication failures exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-USER_LOCKED 5-Notice User [chars] locked out on authentication failure User locked out since the number of authentication failures exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-USER_LOCKED 5-Notice User [chars] locked out on authentication failure User locked out since the number of authentication failures exceeded the configured threshold. aaa LOG_STD_ACTION AAA-5-USER_RESET 5-Notice User [chars] failed attempts reset by [chars] User's number of failed authentication attempts so far has been reset to zero aaa LOG_STD_ACTION AAA-5-USER_RESET 5-Notice User [chars] failed attempts reset by [chars] User's number of failed authentication attempts so far has been reset to zero aaa LOG_STD_ACTION AAA-5-USER_RESET 5-Notice User [chars] failed attempts reset by [chars] User's number of failed authentication attempts so far has been reset to zero aaa LOG_STD_ACTION AAA-5-USER_RESET 5-Notice User [chars] failed attempts reset by [chars] User's number of failed authentication attempts so far has been reset to zero aaa LOG_STD_ACTION AAA-5-USER_UNLOCKED 5-Notice User [chars] unlocked by [chars] User unlocked by the system administrator. User is enabled to login to the system. aaa LOG_STD_ACTION AAA-5-USER_UNLOCKED 5-Notice User [chars] unlocked by [chars] User unlocked by the system administrator. User is enabled to login to the system. aaa LOG_STD_ACTION AAA-5-USER_UNLOCKED 5-Notice User [chars] unlocked by [chars] User unlocked by the system administrator. User is enabled to login to the system. aaa LOG_STD_ACTION AAA-5-USER_UNLOCKED 5-Notice User [chars] unlocked by [chars] User unlocked by the system administrator. User is enabled to login to the system. aaa LOG_STD_ACTION AAA-6-ACCTSESSIDWRAP 6-Information Accounting-Session-ID [dec] exceeded max value allowed Accounting-Session-ID value exceeded max value allowed. Now it is wrapping. aaa "This is informational only not an error." AAA-6-ACCTSESSIDWRAP 6-Information Accounting-Session-ID [dec] exceeded max value allowed Accounting-Session-ID value exceeded max value allowed. Now it is wrapping. aaa "This is informational only not an error." AAA-6-ACCTSESSIDWRAP 6-Information Accounting-Session-ID [dec] exceeded max value allowed Accounting-Session-ID value exceeded max value allowed. Now it is wrapping. aaa "This is informational only not an error." AAA-6-ACCTSESSIDWRAP 6-Information Accounting-Session-ID [dec] exceeded max value allowed Accounting-Session-ID value exceeded max value allowed. Now it is wrapping. aaa "This is informational only not an error." AAA-6-BADHDL 6-Information invalid hdl AAA ID [dec] hdl [hec] [chars] A AAA client has provided an invalid attribute list handle to AAA. aaa LOG_STD_ACTION AAA-6-BADHDL 6-Information invalid hdl AAA ID [dec] hdl [hec] [chars] A AAA client has provided an invalid attribute list handle to AAA. aaa LOG_STD_ACTION AAA-6-BADHDL 6-Information invalid hdl AAA ID [dec] hdl [hec] [chars] A AAA client has provided an invalid attribute list handle to AAA. aaa LOG_STD_ACTION AAA-6-BADHDL 6-Information invalid hdl AAA ID [dec] hdl [hec] [chars] A AAA client has provided an invalid attribute list handle to AAA. aaa LOG_STD_ACTION AAA-6-INVALIDROUTE 6-Information Syntax error in route statement: [chars] Currently downloading route contains syntax error. aaa LOG_STD_ACTION AAA-6-INVALIDROUTE 6-Information Syntax error in route statement: [chars] Currently downloading route contains syntax error. aaa LOG_STD_ACTION AAA-6-INVALIDROUTE 6-Information Syntax error in route statement: [chars] Currently downloading route contains syntax error. aaa LOG_STD_ACTION AAA-6-INVALIDROUTE 6-Information Syntax error in route statement: [chars] Currently downloading route contains syntax error. aaa LOG_STD_ACTION AAA-6-SKIP_MOH_ATTRIBUTE 6-Information Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization. \nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes. aaa LOG_STD_ACTION AAA-6-SKIP_MOH_ATTRIBUTE 6-Information Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization. \nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes. aaa LOG_STD_ACTION AAA-6-SKIP_MOH_ATTRIBUTE 6-Information Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization. \nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes. aaa LOG_STD_ACTION AAA-6-SKIP_MOH_ATTRIBUTE 6-Information Warning: Hardware idb is NULL. No Modem. MoH attribute can not be applied and it is Skipped for authorization. \nTo handle Modem-on-Hold attribute we need connectivity with modems supporting V.92 modem standards. If there is no modem there wouldn't be any tty without which we cannot use MOH attributes. aaa LOG_STD_ACTION AAA-6-USER_BLOCKED 6-Information Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication \nNone method authentication is not allowed in CLI aaa LOG_STD_ACTION AAA-6-USER_BLOCKED 6-Information Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication \nNone method authentication is not allowed in CLI aaa LOG_STD_ACTION AAA-6-USER_BLOCKED 6-Information Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication \nNone method authentication is not allowed in CLI aaa LOG_STD_ACTION AAA-6-USER_BLOCKED 6-Information Enable view requires to be authenticated by non-none methods Please use the appropriate method with the login authentication \nNone method authentication is not allowed in CLI aaa LOG_STD_ACTION AAA-6-USER_FAIL_VIEW_AAA 6-Information User [chars] failed to enter view '[chars]'. You have provided wrong User ID or Password for the requested view aaa "This message is for information only. No action" " is required." AAA-6-USER_FAIL_VIEW_AAA 6-Information User [chars] failed to enter view '[chars]'. You have provided wrong User ID or Password for the requested view aaa "This message is for information only. No action" " is required." AAA-6-USER_FAIL_VIEW_AAA 6-Information User [chars] failed to enter view '[chars]'. You have provided wrong User ID or Password for the requested view aaa "This message is for information only. No action" " is required." AAA-6-USER_FAIL_VIEW_AAA 6-Information User [chars] failed to enter view '[chars]'. You have provided wrong User ID or Password for the requested view aaa "This message is for information only. No action" " is required." AAAA-3-AAAFORKFAIL 3-Error Failed to start AAA process. AAA requests may not be processed. Failed to create the AAA process. aaa "Free up some memory." AAAA-3-AAAFORKFAIL 3-Error Failed to start AAA process. AAA requests may not be processed. Failed to create the AAA process. aaa "Free up some memory." AAAA-3-AAAFORKFAIL 3-Error Failed to start AAA process. AAA requests may not be processed. Failed to create the AAA process. aaa "Free up some memory." AAAA-3-AAAFORKFAIL 3-Error Failed to start AAA process. AAA requests may not be processed. Failed to create the AAA process. aaa "Free up some memory." AAAA-3-ACCTATTR 3-Error last accounting attribute: The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTATTR 3-Error last accounting attribute: The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTATTR 3-Error last accounting attribute: The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTATTR 3-Error last accounting attribute: The data buffer overflowed while building the accounting packet.The accounting attribute that was being written to the buffer while the buffer overflow occured was logged. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTDUMP 3-Error dump of accounting data: The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTDUMP 3-Error dump of accounting data: The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTDUMP 3-Error dump of accounting data: The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTDUMP 3-Error dump of accounting data: The data buffer overflowed while building the accounting packet as the total length of the attributes exceed the buffer size. Last 128 bytes of buffer data is dumped. AAA LOG_STD_ACTION"Collect the logs with these debugs by" " using commands #debug aaa api#debug aaa attr#debug aaa accounting" AAAA-3-ACCTFORKFAIL 3-Error Failed to start accounting process. Accounting records may not be sent. Failed to create the accounting process. aaa "Free up some memory." AAAA-3-ACCTFORKFAIL 3-Error Failed to start accounting process. Accounting records may not be sent. Failed to create the accounting process. aaa "Free up some memory." AAAA-3-ACCTFORKFAIL 3-Error Failed to start accounting process. Accounting records may not be sent. Failed to create the accounting process. aaa "Free up some memory." AAAA-3-ACCTFORKFAIL 3-Error Failed to start accounting process. Accounting records may not be sent. Failed to create the accounting process. aaa "Free up some memory." AAAA-3-BADARG 3-Error %% AAA: bad argument %0#4x We tried to NVGEN a non-existent AAA command. aaa LOG_STD_ACTION AAAA-3-BADARG 3-Error %% AAA: bad argument %0#4x We tried to NVGEN a non-existent AAA command. aaa LOG_STD_ACTION AAAA-3-BADARG 3-Error %% AAA: bad argument %0#4x We tried to NVGEN a non-existent AAA command. aaa LOG_STD_ACTION AAAA-3-BADARG 3-Error %% AAA: bad argument %0#4x We tried to NVGEN a non-existent AAA command. aaa LOG_STD_ACTION AAAA-3-BADAUTHENSTR 3-Error Bad authentication data: [chars] The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size. AAA LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication" AAAA-3-BADAUTHENSTR 3-Error Bad authentication data: [chars] The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size. AAA LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication" AAAA-3-BADAUTHENSTR 3-Error Bad authentication data: [chars] The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size. AAA LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication" AAAA-3-BADAUTHENSTR 3-Error Bad authentication data: [chars] The data buffer overflowed while building the authentication packet as the total length of the attributes exceeded the buffer size. AAA LOG_STD_ACTION"Collect the logs with these debugs" " by using the commands #debug aaa api#debug aaa attr#debug aaa" " authentication" AAAA-3-BADCOMM 3-Error Trying config command but should not be. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-BADCOMM 3-Error Trying config command but should not be. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-BADCOMM 3-Error Trying config command but should not be. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-BADCOMM 3-Error Trying config command but should not be. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-BADLIST 3-Error %% AAA: bad [chars] list [chars] One of the AAA methods does not seem to have a list associated with it. aaa LOG_STD_ACTION AAAA-3-BADLIST 3-Error %% AAA: bad [chars] list [chars] One of the AAA methods does not seem to have a list associated with it. aaa LOG_STD_ACTION AAAA-3-BADLIST 3-Error %% AAA: bad [chars] list [chars] One of the AAA methods does not seem to have a list associated with it. aaa LOG_STD_ACTION AAAA-3-BADLIST 3-Error %% AAA: bad [chars] list [chars] One of the AAA methods does not seem to have a list associated with it. aaa LOG_STD_ACTION AAAA-3-BADREG 3-Error Illegal registry call. An internal software error has occurred aaa LOG_STD_ACTION AAAA-3-BADREG 3-Error Illegal registry call. An internal software error has occurred aaa LOG_STD_ACTION AAAA-3-BADREG 3-Error Illegal registry call. An internal software error has occurred aaa LOG_STD_ACTION AAAA-3-BADREG 3-Error Illegal registry call. An internal software error has occurred aaa LOG_STD_ACTION AAAA-3-BADSTATE 3-Error \n%% AAA: Bad state for [chars] list name [dec] A AAA method list is neither default nor named. This is bad. aaa LOG_STD_ACTION AAAA-3-BADSTATE 3-Error \n%% AAA: Bad state for [chars] list name [dec] A AAA method list is neither default nor named. This is bad. aaa LOG_STD_ACTION AAAA-3-BADSTATE 3-Error \n%% AAA: Bad state for [chars] list name [dec] A AAA method list is neither default nor named. This is bad. aaa LOG_STD_ACTION AAAA-3-BADSTATE 3-Error \n%% AAA: Bad state for [chars] list name [dec] A AAA method list is neither default nor named. This is bad. aaa LOG_STD_ACTION AAAA-3-BADSTR 3-Error Bad accounting data: [chars] During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-BADSTR 3-Error Bad accounting data: [chars] During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-BADSTR 3-Error Bad accounting data: [chars] During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-BADSTR 3-Error Bad accounting data: [chars] During AAA accounting operations the internal database of accounting information for a user was found to be corrupt. In all cases this indicates an internal software error and that accounting information for a particular user session has been lost. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-DLRFORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa LOG_STD_ACTION AAAA-3-DLRFORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa LOG_STD_ACTION AAAA-3-DLRFORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa LOG_STD_ACTION AAAA-3-DLRFORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa LOG_STD_ACTION AAAA-3-DROPACCTFULLQ 3-Error Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars] An accounting record was dropped because there are too many accounting packets enqueued. aaa "Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high." AAAA-3-DROPACCTFULLQ 3-Error Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars] An accounting record was dropped because there are too many accounting packets enqueued. aaa "Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high." AAAA-3-DROPACCTFULLQ 3-Error Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars] An accounting record was dropped because there are too many accounting packets enqueued. aaa "Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high." AAAA-3-DROPACCTFULLQ 3-Error Accounting record dropped due to a full aaa accounting queue: [chars]-[chars] [chars] [chars] An accounting record was dropped because there are too many accounting packets enqueued. aaa "Disable periodic accounting if it is on. The accounting queue may " "have grown to be large which is usually due to a non-responsive " "AAA server. Use 'show radius statistics' or 'show tacacs' to see " "if the number of timeouts is increasing or if the response delay is " "unusually high." AAAA-3-DROPACCTLOWMEM 3-Error Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars] An accounting record dropped due to low memory. aaa "Disable periodic accounting if it is on. Try to reduce the load " "on the router." AAAA-3-DROPACCTLOWMEM 3-Error Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars] An accounting record dropped due to low memory. aaa "Disable periodic accounting if it is on. Try to reduce the load " "on the router." AAAA-3-DROPACCTLOWMEM 3-Error Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars] An accounting record dropped due to low memory. aaa "Disable periodic accounting if it is on. Try to reduce the load " "on the router." AAAA-3-DROPACCTLOWMEM 3-Error Accounting record dropped due to low memory: [chars]-[chars] [chars] [chars] An accounting record dropped due to low memory. aaa "Disable periodic accounting if it is on. Try to reduce the load " "on the router." AAAA-3-DROPACCTQUEUEEXCEEDED 3-Error accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\ An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit. aaa "Disable periodic accounting if it is on. " "[no] aaa accounting update newinfo " "periodic " AAAA-3-DROPACCTQUEUEEXCEEDED 3-Error accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\ An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit. aaa "Disable periodic accounting if it is on. " "[no] aaa accounting update newinfo " "periodic " AAAA-3-DROPACCTQUEUEEXCEEDED 3-Error accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\ An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit. aaa "Disable periodic accounting if it is on. " "[no] aaa accounting update newinfo " "periodic " AAAA-3-DROPACCTQUEUEEXCEEDED 3-Error accounting record dropped output record queue full: [chars]-[chars] [chars] [chars]\n\ An accounting record was dropped. The record could not be enqueued because the number of records in the output queue has exceeded the system limit. aaa "Disable periodic accounting if it is on. " "[no] aaa accounting update newinfo " "periodic " AAAA-3-DROPACCTSNDFAIL 3-Error Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars] An attempt to send an accounting record to a server failed. aaa "Check that the server TACACS+ or RADIUS is operational. Next " AAAA-3-DROPACCTSNDFAIL 3-Error Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars] An attempt to send an accounting record to a server failed. aaa "Check that the server TACACS+ or RADIUS is operational. Next " AAAA-3-DROPACCTSNDFAIL 3-Error Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars] An attempt to send an accounting record to a server failed. aaa "Check that the server TACACS+ or RADIUS is operational. Next " AAAA-3-DROPACCTSNDFAIL 3-Error Accounting record dropped send to server failed: [chars]-[chars] [chars] [chars] An attempt to send an accounting record to a server failed. aaa "Check that the server TACACS+ or RADIUS is operational. Next " AAAA-3-ILLEGALNAME 3-Error Illegal [chars] [chars] name \[chars]\ rejected A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-3-ILLEGALNAME 3-Error Illegal [chars] [chars] name \[chars]\ rejected A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-3-ILLEGALNAME 3-Error Illegal [chars] [chars] name \[chars]\ rejected A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-3-ILLEGALNAME 3-Error Illegal [chars] [chars] name \[chars]\ rejected A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-3-ILLSGNAME 3-Error Illegal server-group name [chars] type [chars]. The given server-group name is a name that could conflict with internally chosen lists. aaa "Please pick a different server-group name." AAAA-3-ILLSGNAME 3-Error Illegal server-group name [chars] type [chars]. The given server-group name is a name that could conflict with internally chosen lists. aaa "Please pick a different server-group name." AAAA-3-ILLSGNAME 3-Error Illegal server-group name [chars] type [chars]. The given server-group name is a name that could conflict with internally chosen lists. aaa "Please pick a different server-group name." AAAA-3-ILLSGNAME 3-Error Illegal server-group name [chars] type [chars]. The given server-group name is a name that could conflict with internally chosen lists. aaa "Please pick a different server-group name." AAAA-3-INTERNAL_ERROR 3-Error [chars] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INTERNAL_ERROR 3-Error [chars] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INTERNAL_ERROR 3-Error [chars] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INTERNAL_ERROR 3-Error [chars] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-INVALIDATTRLIST 3-Error aaa attribute list CLI is not valid when configuring in sub-mode. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-INVALIDLIST 3-Error %% AAA: invalid [chars] list [dec]. One of the AAA methods lists has inconsistent settings aaa LOG_STD_ACTION AAAA-3-INVALIDLIST 3-Error %% AAA: invalid [chars] list [dec]. One of the AAA methods lists has inconsistent settings aaa LOG_STD_ACTION AAAA-3-INVALIDLIST 3-Error %% AAA: invalid [chars] list [dec]. One of the AAA methods lists has inconsistent settings aaa LOG_STD_ACTION AAAA-3-INVALIDLIST 3-Error %% AAA: invalid [chars] list [dec]. One of the AAA methods lists has inconsistent settings aaa LOG_STD_ACTION AAAA-3-INVSTATE 3-Error [chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec] One of the two mentioned data-structures is not set but is needed here. This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INVSTATE 3-Error [chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec] One of the two mentioned data-structures is not set but is needed here. This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INVSTATE 3-Error [chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec] One of the two mentioned data-structures is not set but is needed here. This is an internal software error. aaa LOG_STD_ACTION AAAA-3-INVSTATE 3-Error [chars] AUTHOR/[chars]: Internal state is invalid: astruct 0x[hec] ustruct 0x[hec] One of the two mentioned data-structures is not set but is needed here. This is an internal software error. aaa LOG_STD_ACTION AAAA-3-LISTCREATE 3-Error The list [dec] for [chars] is NULL. This should never be. One of the method-lists created at startup wasn't created. This may cause a reload aaa LOG_STD_ACTION AAAA-3-LISTCREATE 3-Error The list [dec] for [chars] is NULL. This should never be. One of the method-lists created at startup wasn't created. This may cause a reload aaa LOG_STD_ACTION AAAA-3-LISTCREATE 3-Error The list [dec] for [chars] is NULL. This should never be. One of the method-lists created at startup wasn't created. This may cause a reload aaa LOG_STD_ACTION AAAA-3-LISTCREATE 3-Error The list [dec] for [chars] is NULL. This should never be. One of the method-lists created at startup wasn't created. This may cause a reload aaa LOG_STD_ACTION AAAA-3-MKTIMERFAIL 3-Error Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records. Failed to malloc a timer struct for periodic accounting. aaa "Free up some memory and have user re-authenticate." AAAA-3-MKTIMERFAIL 3-Error Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records. Failed to malloc a timer struct for periodic accounting. aaa "Free up some memory and have user re-authenticate." AAAA-3-MKTIMERFAIL 3-Error Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records. Failed to malloc a timer struct for periodic accounting. aaa "Free up some memory and have user re-authenticate." AAAA-3-MKTIMERFAIL 3-Error Failed to create periodic accounting timer for user [chars]. This user may not generate periodic accounting records. Failed to malloc a timer struct for periodic accounting. aaa "Free up some memory and have user re-authenticate." AAAA-3-MKTIMERINVALID 3-Error Invalid request to create periodic accounting timer for user [chars]. Timer already exists. Invalid client usuage of timer struct for periodic accounting. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-MKTIMERINVALID 3-Error Invalid request to create periodic accounting timer for user [chars]. Timer already exists. Invalid client usuage of timer struct for periodic accounting. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-MKTIMERINVALID 3-Error Invalid request to create periodic accounting timer for user [chars]. Timer already exists. Invalid client usuage of timer struct for periodic accounting. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-MKTIMERINVALID 3-Error Invalid request to create periodic accounting timer for user [chars]. Timer already exists. Invalid client usuage of timer struct for periodic accounting. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NOADMINPROC 3-Error [chars] Administrative process has been enabled but somehow could not run - - AAAA-3-NOADMINPROC 3-Error [chars] Administrative process has been enabled but somehow could not run - - AAAA-3-NOADMINPROC 3-Error [chars] Administrative process has been enabled but somehow could not run - - AAAA-3-NOADMINPROC 3-Error [chars] Administrative process has been enabled but somehow could not run - - AAAA-3-NOFREELISTS 3-Error %% AAA: No free [chars] lists for \[chars]\ You have reached the maximum number of possible authentication lists for this method. aaa LOG_STD_RECUR_ACTION AAAA-3-NOFREELISTS 3-Error %% AAA: No free [chars] lists for \[chars]\ You have reached the maximum number of possible authentication lists for this method. aaa LOG_STD_RECUR_ACTION AAAA-3-NOFREELISTS 3-Error %% AAA: No free [chars] lists for \[chars]\ You have reached the maximum number of possible authentication lists for this method. aaa LOG_STD_RECUR_ACTION AAAA-3-NOFREELISTS 3-Error %% AAA: No free [chars] lists for \[chars]\ You have reached the maximum number of possible authentication lists for this method. aaa LOG_STD_RECUR_ACTION AAAA-3-NOLIST 3-Error [chars]: no method list-name. An internal software error. aaa LOG_STD_ACTION AAAA-3-NOLIST 3-Error [chars]: no method list-name. An internal software error. aaa LOG_STD_ACTION AAAA-3-NOLIST 3-Error [chars]: no method list-name. An internal software error. aaa LOG_STD_ACTION AAAA-3-NOLIST 3-Error [chars]: no method list-name. An internal software error. aaa LOG_STD_ACTION AAAA-3-NOREG 3-Error [chars] method [dec] has no registry! An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOREG 3-Error [chars] method [dec] has no registry! An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOREG 3-Error [chars] method [dec] has no registry! An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOREG 3-Error [chars] method [dec] has no registry! An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSERV 3-Error No name for servergroup in method [chars] An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSERV 3-Error No name for servergroup in method [chars] An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSERV 3-Error No name for servergroup in method [chars] An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSERV 3-Error No name for servergroup in method [chars] An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSG 3-Error No server-group passed through parser. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSG 3-Error No server-group passed through parser. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSG 3-Error No server-group passed through parser. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NOSG 3-Error No server-group passed through parser. An internal error has occurred aaa LOG_STD_ACTION AAAA-3-NULPORT 3-Error Could not establish port information This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULPORT 3-Error Could not establish port information This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULPORT 3-Error Could not establish port information This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULPORT 3-Error Could not establish port information This message indicates an internal software error. AAA could not determine a valid port string based on the information provided to it via a client. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULUSR 3-Error accounting for null user This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULUSR 3-Error accounting for null user This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULUSR 3-Error accounting for null user This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-NULUSR 3-Error accounting for null user This message indicates an internal software error. During shutdown of a line or interface the system tried to send accounting information via AAA but could not find the user to which the accounting information belonged. The most likely reason for this error is trying to do accounting twice for the same event. This error message can occur without any loss of accounting information. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-OVERWRITE 3-Error Overwrote internal buffer space [chars] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-OVERWRITE 3-Error Overwrote internal buffer space [chars] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-OVERWRITE 3-Error Overwrote internal buffer space [chars] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-OVERWRITE 3-Error Overwrote internal buffer space [chars] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-PERIODICFORKFAIL 3-Error Failed to start periodic accounting process. Periodic accounting records may not be sent. Failed to create the periodic accounting process. aaa "Free up some memory." AAAA-3-PERIODICFORKFAIL 3-Error Failed to start periodic accounting process. Periodic accounting records may not be sent. Failed to create the periodic accounting process. aaa "Free up some memory." AAAA-3-PERIODICFORKFAIL 3-Error Failed to start periodic accounting process. Periodic accounting records may not be sent. Failed to create the periodic accounting process. aaa "Free up some memory." AAAA-3-PERIODICFORKFAIL 3-Error Failed to start periodic accounting process. Periodic accounting records may not be sent. Failed to create the periodic accounting process. aaa "Free up some memory." AAAA-3-PERNOTIMER 3-Error AAA/ACCT/TIMER: Periodic update but no timer. We are trying to free a timer and the method is PERIODIC but no timer seems to exist. aaa LOG_STD_ACTION AAAA-3-PERNOTIMER 3-Error AAA/ACCT/TIMER: Periodic update but no timer. We are trying to free a timer and the method is PERIODIC but no timer seems to exist. aaa LOG_STD_ACTION AAAA-3-PERNOTIMER 3-Error AAA/ACCT/TIMER: Periodic update but no timer. We are trying to free a timer and the method is PERIODIC but no timer seems to exist. aaa LOG_STD_ACTION AAAA-3-PERNOTIMER 3-Error AAA/ACCT/TIMER: Periodic update but no timer. We are trying to free a timer and the method is PERIODIC but no timer seems to exist. aaa LOG_STD_ACTION AAAA-3-RELOGIN 3-Error sanity check in re-login [chars] to [chars] A software or hardware error occurred. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-RELOGIN 3-Error sanity check in re-login [chars] to [chars] A software or hardware error occurred. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-RELOGIN 3-Error sanity check in re-login [chars] to [chars] A software or hardware error occurred. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-RELOGIN 3-Error sanity check in re-login [chars] to [chars] A software or hardware error occurred. aaa "Copy the error message exactly as it appears and report it to your " "technical support representative." AAAA-3-SGDUPFREE 3-Error Duplicate free of server group 0x[hec] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-SGDUPFREE 3-Error Duplicate free of server group 0x[hec] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-SGDUPFREE 3-Error Duplicate free of server group 0x[hec] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-SGDUPFREE 3-Error Duplicate free of server group 0x[hec] This is an internal software error. aaa LOG_STD_ACTION AAAA-3-STRCREATE 3-Error str_create overwrote its internal buffer. An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory. aaa LOG_STD_ACTION AAAA-3-STRCREATE 3-Error str_create overwrote its internal buffer. An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory. aaa LOG_STD_ACTION AAAA-3-STRCREATE 3-Error str_create overwrote its internal buffer. An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory. aaa LOG_STD_ACTION AAAA-3-STRCREATE 3-Error str_create overwrote its internal buffer. An internal buffer used to assemble a string was exceeded thus possibly corrupting other memory. aaa LOG_STD_ACTION AAAA-3-SUBTYPE 3-Error Bad Subtype [dec] for \[chars]\ [dec] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-SUBTYPE 3-Error Bad Subtype [dec] for \[chars]\ [dec] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-SUBTYPE 3-Error Bad Subtype [dec] for \[chars]\ [dec] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-SUBTYPE 3-Error Bad Subtype [dec] for \[chars]\ [dec] An internal software error. aaa "Report to tac@cisco.com." AAAA-3-TIMERNOPER 3-Error AAA/ACCT/TIMER: No periodic update but timer set. We are trying to free a timer but the update method is not PERIODIC and so no timer should exist. aaa LOG_STD_ACTION AAAA-3-TIMERNOPER 3-Error AAA/ACCT/TIMER: No periodic update but timer set. We are trying to free a timer but the update method is not PERIODIC and so no timer should exist. aaa LOG_STD_ACTION AAAA-3-TIMERNOPER 3-Error AAA/ACCT/TIMER: No periodic update but timer set. We are trying to free a timer but the update method is not PERIODIC and so no timer should exist. aaa LOG_STD_ACTION AAAA-3-TIMERNOPER 3-Error AAA/ACCT/TIMER: No periodic update but timer set. We are trying to free a timer but the update method is not PERIODIC and so no timer should exist. aaa LOG_STD_ACTION AAAA-4-BADMETHNAME 4-Warning Bad [chars] method-list name \[chars]\ this is only a warning A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-4-BADMETHNAME 4-Warning Bad [chars] method-list name \[chars]\ this is only a warning A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-4-BADMETHNAME 4-Warning Bad [chars] method-list name \[chars]\ this is only a warning A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-4-BADMETHNAME 4-Warning Bad [chars] method-list name \[chars]\ please choose another name A method-list name should not be the same as a method name. Please choose a different name for the method list. aaa "Pick a different method-list name that is not also a method-name." AAAA-4-BADSGNAME 4-Warning Bad server-group name [chars] type [chars]. The given server-group name either doesn't exist or the given type does not match the defined server-group. aaa "Verify that the group exists and has the same " "type." AAAA-4-BADSGNAME 4-Warning Bad server-group name [chars] type [chars]. The given server-group name either doesn't exist or the given type does not match the defined server-group. aaa "Verify that the group exists and has the same " "type." AAAA-4-BADSGNAME 4-Warning Bad server-group name [chars] type [chars]. The given server-group name either doesn't exist or the given type does not match the defined server-group. aaa "Verify that the group exists and has the same " "type." AAAA-4-BADSGNAME 4-Warning Bad server-group name [chars] type [chars]. The given server-group name either doesn't exist or the given type does not match the defined server-group. aaa "Verify that the group exists and has the same " "type." AAAA-4-BADSGTYPE 4-Warning Server-group [chars] is not of type [chars]. The given server-group name does not match the specified type aaa "Verify that the group exists and has " "the same type." AAAA-4-BADSGTYPE 4-Warning Server-group [chars] is not of type [chars]. The given server-group name does not match the specified type aaa "Verify that the group exists and has " "the same type." AAAA-4-BADSGTYPE 4-Warning Server-group [chars] is not of type [chars]. The given server-group name does not match the specified type aaa "Verify that the group exists and has " "the same type." AAAA-4-BADSGTYPE 4-Warning Server-group [chars] is not of type [chars]. The given server-group name does not match the specified type aaa "Verify that the group exists and has " "the same type." AAAA-4-CLI_DEPRECATED 4-Warning [chars] CLI deprecated. New CLI to be used aaa LOG_STD_ACTION AAAA-4-CLI_DEPRECATED 4-Warning [chars] CLI deprecated. New CLI to be used aaa LOG_STD_ACTION AAAA-4-CLI_DEPRECATED 4-Warning [chars] CLI deprecated. New CLI to be used aaa LOG_STD_ACTION AAAA-4-CLI_DEPRECATED 4-Warning [chars] CLI deprecated. New CLI to be used aaa LOG_STD_ACTION AAAA-4-DNISGPUNDEF 4-Warning Warning: DNIS group [chars] is not defined. The DNIS group was used without defining it first. It should be defined before use. aaa "Define the DNIS group before using it." AAAA-4-DNISGPUNDEF 4-Warning Warning: DNIS group [chars] is not defined. The DNIS group was used without defining it first. It should be defined before use. aaa "Define the DNIS group before using it." AAAA-4-DNISGPUNDEF 4-Warning Warning: DNIS group [chars] is not defined. The DNIS group was used without defining it first. It should be defined before use. aaa "Define the DNIS group before using it." AAAA-4-DNISGPUNDEF 4-Warning Warning: DNIS group [chars] is not defined. The DNIS group was used without defining it first. It should be defined before use. aaa "Define the DNIS group before using it." AAAA-4-NOCACHEPROC 4-Warning The aaa cache process is not created. Please configure aaa cache profile first Cache was listed in a method-list without defining it first. Cache profile should be defined before use. aaa "Define the cache profile before using it." AAAA-4-NOCACHEPROC 4-Warning The aaa cache process is not created. Please configure aaa cache profile first Cache was listed in a method-list without defining it first. Cache profile should be defined before use. aaa "Define the cache profile before using it." AAAA-4-NOCACHEPROC 4-Warning The aaa cache process is not created. Please configure aaa cache profile first Cache was listed in a method-list without defining it first. Cache profile should be defined before use. aaa "Define the cache profile before using it." AAAA-4-NOCACHEPROC 4-Warning The aaa cache process is not created. Please configure aaa cache profile first Cache was listed in a method-list without defining it first. Cache profile should be defined before use. aaa "Define the cache profile before using it." AAAA-4-NOSERVER 4-Warning Warning: Server [chars] is not defined. The given server is not on the master-list and should be defined or unexpected things might happen. aaa "Please define the server on the appropriate " "master-list as soon as possible." AAAA-4-NOSERVER 4-Warning Warning: Server [chars] is not defined. The given server is not on the master-list and should be defined or unexpected things might happen. aaa "Please define the server on the appropriate " "master-list as soon as possible." AAAA-4-NOSERVER 4-Warning Warning: Server [chars] is not defined. The given server is not on the master-list and should be defined or unexpected things might happen. aaa "Please define the server on the appropriate " "master-list as soon as possible." AAAA-4-NOSERVER 4-Warning Warning: Server [chars] is not defined. The given server is not on the master-list and should be defined or unexpected things might happen. aaa "Please define the server on the appropriate " "master-list as soon as possible." AAAA-4-SERVNOGRP 4-Warning Warning: Server [inet]:[dec][dec] is not part of server group [chars]. The server does not belong to the specified server group aaa "Please check that the specified server belongs " "to the server group" AAAA-4-SERVNOGRP 4-Warning Warning: Server [inet]:[dec][dec] is not part of server group [chars]. The server does not belong to the specified server group aaa "Please check that the specified server belongs " "to the server group" AAAA-4-SERVNOGRP 4-Warning Warning: Server [inet]:[dec][dec] is not part of server group [chars]. The server does not belong to the specified server group aaa "Please check that the specified server belongs " "to the server group" AAAA-4-SERVNOGRP 4-Warning Warning: Server [inet]:[dec][dec] is not part of server group [chars]. The server does not belong to the specified server group aaa "Please check that the specified server belongs " "to the server group" AAAA-4-SERVNORADIUS 4-Warning The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a radius server-group." AAAA-4-SERVNORADIUS 4-Warning The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a radius server-group." AAAA-4-SERVNORADIUS 4-Warning The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a radius server-group." AAAA-4-SERVNORADIUS 4-Warning The server-group \[chars]\ is not a radius server group. Please define \[chars]\ as a radius server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a radius server-group." AAAA-4-SERVNOTACPLUS 4-Warning The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a tacacs+ server-group." AAAA-4-SERVNOTACPLUS 4-Warning The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a tacacs+ server-group." AAAA-4-SERVNOTACPLUS 4-Warning The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a tacacs+ server-group." AAAA-4-SERVNOTACPLUS 4-Warning The server-group \[chars]\ is not a tacacs+ server group. Please define \[chars]\ as a tacacs+ server group. The protocol used by the server-group doesn't support the configured aaa action. aaa "Use a tacacs+ server-group." AAAA-4-SERVUNDEF 4-Warning The server-group \[chars]\ is not defined. Please define it. A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use. aaa "Define the server-group before using it." AAAA-4-SERVUNDEF 4-Warning The server-group \[chars]\ is not defined. Please define it. A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use. aaa "Define the server-group before using it." AAAA-4-SERVUNDEF 4-Warning The server-group \[chars]\ is not defined. Please define it. A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use. aaa "Define the server-group before using it." AAAA-4-SERVUNDEF 4-Warning The server-group \[chars]\ is not defined. Please define it. A given server-group was listed in a method-list without defining it first. Server-groups should be defined before use. aaa "Define the server-group before using it." AAAA-4-UNSUPWAITSTART 4-Warning %% AAA: Unsupported option wait-start mapped to start-stop. wait-start accounting is not supported. It is being mapped to start-stop aaa "wait-start accounting is not supported. It is being mapped to start-stop" AAAA-4-UNSUPWAITSTART 4-Warning %% AAA: Unsupported option wait-start mapped to start-stop. wait-start accounting is not supported. It is being mapped to start-stop aaa "wait-start accounting is not supported. It is being mapped to start-stop" AAAA-4-UNSUPWAITSTART 4-Warning %% AAA: Unsupported option wait-start mapped to start-stop. wait-start accounting is not supported. It is being mapped to start-stop aaa "wait-start accounting is not supported. It is being mapped to start-stop" AAAA-4-UNSUPWAITSTART 4-Warning %% AAA: Unsupported option wait-start mapped to start-stop. wait-start accounting is not supported. It is being mapped to start-stop aaa "wait-start accounting is not supported. It is being mapped to start-stop" AAAA-6-ACCTLOCAL 6-Information Username: [chars] Privilege level: [dec] Command: [chars] AAA local accounting log message aaa "This information is to store buffered logs" "locally and send to SYSLOG server" AAAA-6-ACCTLOCAL 6-Information Username: [chars] Privilege level: [dec] Command: [chars] AAA local accounting log message aaa "This information is to store buffered logs" "locally and send to SYSLOG server" AAAA-6-ACCTSTART 6-Information [chars] A AAA accounting start message. aaa "This information is for information only." AAAA-6-ACCTSTART 6-Information [chars] A AAA accounting start message. aaa "This information is for information only." AAAA-6-ACCTSTART 6-Information [chars] A AAA accounting start message. aaa "This information is for information only." AAAA-6-ACCTSTART 6-Information [chars] A AAA accounting start message. aaa "This information is for information only." AAAA-6-ACCTSTOP 6-Information [chars] A AAA accounting stop message. aaa "This information is for information only." AAAA-6-ACCTSTOP 6-Information [chars] A AAA accounting stop message. aaa "This information is for information only." AAAA-6-ACCTSTOP 6-Information [chars] A AAA accounting stop message. aaa "This information is for information only." AAAA-6-ACCTSTOP 6-Information [chars] A AAA accounting stop message. aaa "This information is for information only." AAAA-6-ACCTWATCH 6-Information [chars] A AAA accounting watchdog/update message. aaa "This information is for information only." AAAA-6-ACCTWATCH 6-Information [chars] A AAA accounting watchdog/update message. aaa "This information is for information only." AAAA-6-ACCTWATCH 6-Information [chars] A AAA accounting watchdog/update message. aaa "This information is for information only." AAAA-6-ACCTWATCH 6-Information [chars] A AAA accounting watchdog/update message. aaa "This information is for information only." AAAA-6-ADMINMSG 6-Information [chars] [chars]: [chars] This administrative message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-ADMINMSG 6-Information [chars] [chars]: [chars] This administrative message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-ADMINMSG 6-Information [chars] [chars]: [chars] This administrative message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-ADMINMSG 6-Information [chars] [chars]: [chars] This administrative message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-SERVERMSG 6-Information [chars] [chars]: [chars] This message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-SERVERMSG 6-Information [chars] [chars]: [chars] This message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-SERVERMSG 6-Information [chars] [chars]: [chars] This message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AAAA-6-SERVERMSG 6-Information [chars] [chars]: [chars] This message was passed to the NAS from the AAA server aaa "No action need be taken but the message may " "contain usefull information regarding some event " "on the server" AC-3-AC_SANITY 3-Error [chars] A unexpected sanity check failed during Attachment Circuit processing. ac LOG_STD_ACTION AC-3-AC_SANITY 3-Error [chars] A unexpected sanity check failed during Attachment Circuit processing. ac LOG_STD_ACTION AC-3-AC_WS_REGISTER 3-Error L2VPN WS registration failed for [chars] An error was encountered when attempting to register the specified Attachment Circuit type with the Layer 2 Virtual Private Network Wire Service facility. ac LOG_STD_ACTION AC-3-AC_WS_REGISTER 3-Error L2VPN WS registration failed for [chars] An error was encountered when attempting to register the specified Attachment Circuit type with the Layer 2 Virtual Private Network Wire Service facility. ac LOG_STD_ACTION AC-3-ACMGR_INVALID_HDL 3-Error Received invalid [chars] handle Attachment Circuit Manager receives invalid handle. ac LOG_STD_ACTION AC-3-ACMGR_INVALID_HDL 3-Error Received invalid [chars] handle Attachment Circuit Manager receives invalid handle. ac LOG_STD_ACTION AC-3-ACMGR_INVALID_MSG 3-Error Received [chars] Attachment Circuit Manager receives invalid message. ac LOG_STD_ACTION AC-3-ACMGR_INVALID_MSG 3-Error Received [chars] Attachment Circuit Manager receives invalid message. ac LOG_STD_ACTION AC-3-ACMGR_MISSED_CIRCUIT 3-Error Circuit info missing in [chars] message. AC Manager received message with missing circuit info ac LOG_STD_ACTION AC-3-ACMGR_MISSED_CIRCUIT 3-Error Circuit info missing in [chars] message. AC Manager received message with missing circuit info ac LOG_STD_ACTION AC-3-ACMGR_XDM_CREATE 3-Error Failed to create XDM - rc [dec] Attachment Circuit Manager was unable to create a Dispatch Manager instance for event handling. ac LOG_STD_ACTION AC-3-ACMGR_XDM_CREATE 3-Error Failed to create XDM - rc [dec] Attachment Circuit Manager was unable to create a Dispatch Manager instance for event handling. ac LOG_STD_ACTION AC-3-L2SS_BAD_HANDLE 3-Error Corrupted L2SS handle [[hec]]. An internal L2SS Manager occurred. ac LOG_STD_ACTION AC-3-L2SS_BAD_HANDLE 3-Error Corrupted L2SS handle [[hec]]. An internal L2SS Manager occurred. ac LOG_STD_ACTION AC-3-L2SS_NULL_CONTEXT 3-Error Encountered a NULL context in [chars] Encountered a NULL context in L2SS Manager. ac LOG_STD_ACTION AC-3-L2SS_NULL_CONTEXT 3-Error Encountered a NULL context in [chars] Encountered a NULL context in L2SS Manager. ac LOG_STD_ACTION AC-3-L2SS_UNEXPECTED 3-Error Received unexpected [chars] message L2SS received unexpected message. ac LOG_STD_ACTION AC-3-L2SS_UNEXPECTED 3-Error Received unexpected [chars] message L2SS received unexpected message. ac LOG_STD_ACTION AC-3-L2SS_WRONG_KEYS 3-Error Wrong set of keys in [chars] message SIP sends a wrong set of keys to L2SS Manager. ac LOG_STD_ACTION AC-3-L2SS_WRONG_KEYS 3-Error Wrong set of keys in [chars] message SIP sends a wrong set of keys to L2SS Manager. ac LOG_STD_ACTION ACCESS_IE-3-INVALID_HANDLE 3-Error Caller passed in invalid handle - traceback to follow. An invalid handle was encountered in the Access IE library. - LOG_STD_ACTION ACCESS_SESSION-3-TRACE_INIT_FAIL 3-Error Initialization failed with code: [dec] Failed to initialize access-session trace. dot1x-ios LOG_STD_NO_ACTION ACCESS_SESSION-3-TRACE_INIT_FAIL 3-Error Initialization failed with code: [dec] Failed to initialize access-session trace. dot1x-ios LOG_STD_NO_ACTION ACCESS_SESSION-3-TRACE_INIT_FAIL 3-Error Initialization failed with code: [dec] Failed to initialize access-session trace. dot1x-ios LOG_STD_NO_ACTION ACCESS_SESSION-3-TRACE_REG_FAIL 3-Error Component [chars] registration failed. Error code: [dec] Component failed to register with access-session trace dot1x-ios LOG_STD_NO_ACTION ACCESS_SESSION-3-TRACE_REG_FAIL 3-Error Component [chars] registration failed. Error code: [dec] Component failed to register with access-session trace dot1x-ios LOG_STD_NO_ACTION ACCESS_SESSION-3-TRACE_REG_FAIL 3-Error Component [chars] registration failed. Error code: [dec] Component failed to register with access-session trace dot1x-ios LOG_STD_NO_ACTION ACCESS_TUNNEL_ISSU-3-BUFFER 3-Error ACCESS_TUNNEL ISSU client failed to get buffer for message error [dec] ACCESS_TUNNEL ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can not send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. accsw-p-securefab "show logging and show checkpoint client" ACCESS_TUNNEL_ISSU-3-CAP_INVALID_SIZE 3-Error ACCESS_TUNNEL ISSU client capability list is empty. The ACCESS_TUNNEL ISSU client capability exchange list size\n\ is invalid. accsw-p-securefab "show issu capability entries " ACCESS_TUNNEL_ISSU-3-CAP_NOT_COMPATIBLE 3-Error ACCESS_TUNNEL ISSU client capability exchange result incompatible. The ACCESS_TUNNEL ISSU client capability exchange has negotiated\n\ as incompatible with the peer. accsw-p-securefab "show issu negotiated capability " ACCESS_TUNNEL_ISSU-3-CAPABILITY 3-Error ACCESS_TUNNEL ISSU client [chars] ACCESS_TUNNEL ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit. accsw-p-securefab "show issu capability entries and \n\ show issu session and \n\ show issu negotiated capability " ACCESS_TUNNEL_ISSU-3-INIT 3-Error ACCESS_TUNNEL ISSU client initialization failed at [chars] error [chars] ACCESS_TUNNEL ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. accsw-p-securefab LOG_STD_SH_TECH_ACTION ACCESS_TUNNEL_ISSU-3-MSG_NOT_OK 3-Error ACCESS_TUNNEL ISSU client message [dec] is not compatible ACCESS_TUNNEL ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can not be processed by this unit accsw-p-securefab "show issu message group and\n\ show issu session and \n\ show issu negotiated version " ACCESS_TUNNEL_ISSU-3-MSG_SIZE 3-Error ACCESS_TUNNEL ISSU client failed to get the message size for message [dec] ACCESS_TUNNEL ISSU client failed to calculate message size\n\ for the message specified. The ACCESS_TUNNEL ISSU client will not\n\ be able to send message to the standby unit. accsw-p-securefab "show issu message group and\n\ show issu session and \n\ show issu negotiated version " ACCESS_TUNNEL_ISSU-3-POLICY 3-Error ACCESS_TUNNEL ISSU client message type [dec] is [chars] ACCESS_TUNNEL ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible. accsw-p-securefab "show issu session " ACCESS_TUNNEL_ISSU-3-SEND_FAILED 3-Error ACCESS_TUNNEL ISSU client failed to send a negotiation message error [dec] ACCESS_TUNNEL ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the \n\ negotiation the standby unit can not be brought up. accsw-p-securefab "show logging and show checkpoint client" ACCESS_TUNNEL_ISSU-3-SESSION 3-Error ACCESS_TUNNEL ISSU client [chars] ACCESS_TUNNEL ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up. accsw-p-securefab "show issu capability entries and \n\ show issu session and \n\ show issu negotiated capability " ACCESS_TUNNEL_ISSU-3-SESSION_UNREGISTRY 3-Error ACCESS_TUNNEL ISSU client failed to unregister session information. Error: [dec] [chars] The ACCESS_TUNNEL ISSU client failed to unregister session information. accsw-p-securefab "show issu session and " "show issu negotiated capability " ACCESS_TUNNEL_ISSU-3-TRANSFORM 3-Error ACCESS_TUNNEL ISSU client [chars] transform failed error [chars] ACCESS_TUNNEL ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the ACCESS_TUNNEL state will not\n\ be indentical with the active unit. accsw-p-securefab "show issu session and \n\ show issu negotiated version " ACE-2-CRYPTOENGERR 2-Critical Crypto engine error: [chars] [dec] A crypto engine operation did not complete. This error condition can indicate that the crypto engine cannot bind or unbind an interface to a crypto engine. It can also indicate that the crypto engine cannot query an interface ID. - "Remove the cryptomap set from the interface by issuing " "no crypto map command. Then reattach the cryptomap " "set to the interface using crypto map command. " "Although removing and reattaching the crypto map might fix the " "cryptographic engine operation failure report the failure to your " "technical support representative along with the sequence of commands " "that lead to the failure". ACE-2-INTTABOPERR 2-Critical Internal [chars] table error: [chars] Internal table operation fails. This means the state of the module is mostly like inconsistent. iosxe-ipsec "Contact your technical support representative" ACE-3-BOOTMSGERR 3-Error [chars]: boot error: [chars] The ACE completed booting but with an error status code. ACE will not operate and it will not register with the crypto subsystem. - "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-CEAL_REGISTRATION 3-Error ACE [chars] failed to register. The ACE failed to register with CEAL iosxe-ipsec "Reset the hw module" ACE-3-CRASHDUMPERR 3-Error [chars]: crashdump retrieval error: [chars] [chars] An error occurred during crashdump file retrieval from ACE. - "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-CRASHDUMPSTART 3-Error [chars]: crashdump retrieval initiated to file [chars] The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem. - "Report the crash and transfer the crashdump file to your technical" "support representative." ACE-3-HAPITRUNC 3-Error [chars]: Received truncated HAPI message tlen=[dec] actual=[dec] An IPsec packet was unexpectedly forwarded to the RP iosxe-ipsec "If this message was seen in the context of the router booting " "enabling the hardware crypto accelerator then this message is normal " "and can be safely ignored. " "Otherwise please copy the error message exactly as it appears " "and report it to your technical support representative." ACE-3-INITFAIL 3-Error [chars]: initialization failed [chars] An error occured in the indicated control transaction. iosxe-ipsec "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-INVTID 3-Error [chars]: [chars] of invalid [chars] trans id [dec] An invalid transaction ID of for the indicated transaction\n\ type was encountered iosxe-ipsec "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-NOENGINESLOT 3-Error Interface [chars] has no crypto engine slot An IKE SA was requested for a given interface but no crypto engine slot was assigned to that interface iosxe-ipsec "Configure the interface in question with the" " `crypto engine [sub]slot' command" ACE-3-NOMORETID 3-Error [chars]: out of [chars] transactions Transaction pool for the indicated transaction type was\n\ exhausted. iosxe-ipsec "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-OUTOFID_RL 3-Error Too many [chars] IDs in the system. Cannot allocate a new one All the IDs of the specified type are in use iosxe-ipsec "Reduce the traffic load number of IPSec tunnels and/or frequency of re-key." "If this message was seen under light loading conditions then" "copy the error message exactly as it appears and report it to your " "technical support representative." ACE-3-OUTOFRES 3-Error Too many [chars] in the system. Cannot allocate a new one All VPN-accelerator resources of a particular are in used and thus this allocation request fails. iosxe-ipsec "Remove the cryptomap set from the interface. " "Reduce the number of that resource in the " "system. For ACL reduce the number of ACL " "permit ACE in the system. For cryptomap reduce the" "number of cryptomaps in the system. For SPD and " "SPD map reduce the number of interface with " "cryptomap set attached." ACE-4-BV_IDMGR_DESTROY 4-Warning ACE failed to destroy [chars] ID manager. Leaking memory. The ACE failed to destroy memory space for ID management. iosxe-ipsec "Copy the error message exactly as it appears and report it to your " "technical support representative." ACE-6-BOOTMSGINFO 6-Information [chars]: boot info: [chars] The ACE completed booting but with a non-zero informational status code. This does not indicate an error and ACE will run normally. - "No action is necessary." ACE-6-CRASHDUMPEND 6-Information [chars]: crashdump retrieval complete The ACE crashed and was rebooted. Upon reboot a crashdump file was detected and uploaded to the sup-bootflash filesystem. - "Report the crash and transfer the crashdump file to your technical" "support representative." ACE-6-INFO 6-Information [chars]: [chars] This is informational message from ACE iosxe-ipsec "This is informational message from ACE. This occurs " "in normal operation." ACE-6-SWITCHOVER 6-Information VPN-SM switchover: [dec]/[dec] has been [chars] [dec]/[dec] An negative acknowledge occured in the indicated control transaction. iosxe-ipsec "Copy the error message exactly as it appears and report it to your " "technical support representative." ACL1-5-LDP 5-Notice 5*ERRMSG_LIMIT_SLOW - - - ACL1-5-LDP 5-Notice 5*ERRMSG_LIMIT_SLOW - - - ACL-3-UNEXPECTED_PKT_TYPE 3-Error type [dec] int [dec] [chars]put ACL logging has encountered unexpected pkt type. cpp-ucode LOG_STD_ACTION ACL-3-UNEXPECTED_STATE 3-Error type [dec] int [chars] [chars]put w0: 0x%p w1: 0x[hec] An error has occurred in the setup of ACL hardware. cpp-ucode LOG_STD_ACTION ACL-5-LDP 5-Notice ERRMSG_NOFLAGS - - - ACL-5-LDP 5-Notice ERRMSG_NOFLAGS - - - ACLMERGE-3-CUDDERROR 3-Error A CUDD Library error was detected in [chars] An error was detected by the CUDD Library the ACL-Merge for this invokation has failed. This could result in more traffic being switched by software. The effect of this could be lower performance for the interface for which the merge failed. aclmerge "Copy and save this message. Report this to Engineering along with the ACL configuration of this device. Use Topic to search for a similar DDTS. If none found write a DDTS for this problem" ACLMERGE-3-CUDDWARN 3-Error A CUDD Library warning message for interest in this event in [chars] Debug message only. No action required aclmerge "Copy and save this message. Report this to Engineering along with the ACL configuration of the device. This is just a debug message of interest to engineering to investigate the case why this happened" ACLMGR-2-NOMAP 2-Critical Cannot create ACL Manager data structures for VLAN Map [chars] The ACL Manager could not allocate the data structures needed to describe a VLAN Map in a form that can be loaded into hardware. Probably caused by lack of free memory. firmware LOG_STD_REDUCE_ACTION ACLMGR-2-NOVLB 2-Critical Cannot create memory block for VLAN [dec] The ACL Manager was unable to save per-VLAN information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly. firmware "Use a less complicated configuration that " "requires less memory." ACLMGR-2-NOVMR 2-Critical Cannot generate hardware representation of access list [chars] There were insufficient resources available for generating a hardware representation of the access list. Either lack of available logical operation units or lack of memory can cause this problem. Logical operation units are needed when a match on TCP flags is specified or when any test other than eq that is: ne gt lt or range is firmware "Modify the ACL configuration to use fewer resources." ACLMGR-3-AUGMENTFAIL 3-Error Augmenting of access-map [chars] on [chars] label [dec] failed The system ran out of CPU DRAM when attempting to merge internally required elements with the configured access maps. firmware LOG_STD_REDUCE_ACTION ACLMGR-3-FEATUREMISMATCH 3-Error [chars] can not be supported with the image running on switch-[dec] A feature has been configured on the stack but can not be supported on one or more switches in the stack. This feature will continue to work on the rest of the switches that support it but will not be applied to the switches that can not support it. All other features continue to work as expected on the stack. firmware "Upgrade the software running on switches that " "can not support this feature. Upgrade to a " "software version that supports this feature." ACLMGR-3-IECPORTLABELERROR 3-Error ACL labels are out-of-sync on interface [chars] label [dec] is not available on asic [dec] An internal software error has occurred. firmware LOG_STD_ACTION ACLMGR-3-INSERTFAIL 3-Error Insert of access-map [chars] #[dec] into [chars] label [dec] failed The system ran out of CPU DRAM when trying to merge sections of an access map. firmware LOG_STD_REDUCE_ACTION ACLMGR-3-INTTABLE 3-Error Not in truth table: VLMAP [dec] RACL [dec] Rtprot [dec] Mcb [dec] Feat [dec] An unrecoverable software error occurred while trying to merge the configured input features. firmware "show running-config" ACLMGR-3-INVALIDL4PORTINDEX 3-Error Invalid L4 port array index while processing [chars] ACL Manager module received invalid value for L4 port array index. The problem can be due to memory corruption or bad system memory. firmware NACL_L4OP_ERROR ACLMGR-3-INVALIDPARAM 3-Error Invalid [chars] [dec] encountered ACL Manager has encountered an invalid parameter value. firmware "show running-config" ACLMGR-3-MAXRECURSION 3-Error Too many [dec] levels of recursion while merging ACLs code [dec]. The configuration is too complicated for the platform specific ACL merge code to support. Most likely cause is including too many separate access lists in a single VLAN map or policy map. firmware "Reduce the number IP or MAC access lists" " considered separately in any one VLAN or policy" ACLMGR-3-MERGEFAIL 3-Error [chars] ACL merge error [dec] [chars] on [chars] label [dec] The ACL Manager was unable to complete the merge of the configured features into a form suitable for loading into the hardware. Packets potentially affected by this feature will be sent to the CPU for processing instead. The most likely cause is specifying an ACL that is too large or too complex for the system to handle. firmware "Try specifying a smaller and less complicated " "configuration." ACLMGR-3-NOLABEL 3-Error Cannot allocate [chars] label for vlan-id [dec] The ACL Manager was unable to allocate a label for the features on this interface. This means that the hardware cannot be programmed to implement the features and packets for this interface will be filtered in software. There is a limit of 256 labels per direction. firmware "Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible." ACLMGR-3-OUTTTABLE 3-Error Not in truth table: RACL [dec] VLMAP [dec] An unrecoverable software error occurred while trying to merge the configured output features. firmware "show running-config" ACLMGR-3-PACLTTABLE 3-Error Not in truth table: IPSrcGrd [dec] PACL [dec] Rtprot [dec] An unrecoverable software error occurred while trying to merge the configured port acl features. firmware "show running-config" ACLMGR-3-QOSTTABLE 3-Error Not in truth table: ACL [dec] in map action [dec] A software error occurred while trying to merge a QoS Policy Map firmware "show running-config" ACLMGR-3-UNKNOWNACTION 3-Error Unknown VMR access group action 0x[hec] An internal software error has occurred. firmware LOG_STD_ACTION ACLMGR-3-UNKNOWNL4OPERATION 3-Error Unknown L4 operation 0x[hec] ACL Manager module received invalid value for L4 operation. The problem can be due to memory corruption or bad system memory. firmware NACL_L4OP_ERROR ACLMGR-4-ACLTCAMFULL 4-Warning [chars]ACL TCAM Full. Software Forwarding packets on [chars] label [dec] on [chars] [chars] The ACL configuration is too large to fit in the platform -specific ACL TCAM table. firmware "Simplify the ACLs applied to interfaces or reduce" " their number." ACLMGR-4-ACLTCAMFULL 4-Warning ACL TCAM Full. [chars] [chars] [chars] [chars] The ACL configuration is too large to fit in the platform -specific ACL TCAM table. firmware "Simplify the ACLs applied to interfaces or reduce" " their number." ACLMGR-4-RELOADED 4-Warning Reloading [chars] [chars] label [dec] [chars] [chars]feature The ACL Manager was able to fit more of the configured features on this label into the hardware. One or more features had previously been unloaded because of lack of space. firmware LOG_STD_NO_ACTION ACLMGR-4-RELOADEDFSPAN 4-Warning Reloading [chars] session [dec] [chars] feature The ACL Manager was able to fit more of the configured Flow based SPAN features on this session into the hardware. One or more features had previously been unloaded because of lack of space. firmware LOG_STD_NO_ACTION ACLMGR-4-UNLOADING 4-Warning Unloading [chars] [chars] label [dec] [chars] [chars]feature The ACL Manager was unable to fit the complete configuration into the hardware so some features will have to be applied in software. This prevents some or all of the packets in a VLAN/port from being forwarded in hardware and requires them to be forwarded by the CPU. Multicast packets may be dropped entirely instead of being forwarded. firmware "Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible." ACLMGR-4-UNLOADINGFSPAN 4-Warning Unloading [chars] session [dec] [chars] feature The ACL Manager was unable to fit the complete Flow based SPAN configuration into the hardware so this feature has been temporarily disabled for the given session. firmware "Allocate more space to the ACL section of the " "TCAM by choosing an SDM template with more ACL " "TCAM space and reboot the switch. You may also " "use a simpler ACL configuration and/or use the " "same ACLs on multiple interfaces if possible." ACR-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. ACR_DDTS_COMPONENT "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ACR-3- ACRIFADD 3-Error [chars] interface add failed for ACR group [dec]. Addition of interface to ACR group failed ACR_DDTS_COMPONENT "Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-3- ACRIFDEL 3-Error [chars] interface del failed for ACR group [dec]. Delete of interface from ACR group failed ACR_DDTS_COMPONENT "Get the output of \"show acr all \" immediately after this error." "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-3- ACRPVCDISABLE 3-Error PVC Disable failed for VCD= [dec] on [chars] interface of ACR interface [chars]. PVC disable failed on ACR physical interface. ACR_DDTS_COMPONENT "Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-3- ACRVPDISABLE 3-Error VP Disable failed for VPI= [dec] on [chars] interface of ACR interface [chars]. VP disable failed on ACR physical interface. ACR_DDTS_COMPONENT "Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-3- ACRVPENABLE 3-Error VP Enable failed for VPI= [dec] on [chars] interface of ACR interface [chars]. VP enable failed on ACR physical interface. ACR_DDTS_COMPONENT "Get the output of \"show acr group \" and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-3-ISSU_SENDFAILED 3-Error \nACR ISSU: send message failed rc = [dec]\n The sending of a message has failed. ACR_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION ACR-4-ISSU_INCOMPATIBLE 4-Warning \nacr-issu-compat: returned FALSE The compatibility checking has failed ACR_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION ACR-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The transform has failed. ACR_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION ACR-6- ACRPVCADD 6-Information PVC creation failed for VCD= [dec] on [chars] interface of ACR interface [chars]. PVC creation attempt failed on ACR physical interface. ACR_DDTS_COMPONENT "If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-6- ACRPVCDEL 6-Information PVC deletion failed for VCD= [dec] on [chars] interface of ACR group [chars]. PVC deletion attempt failed on ACR physical interface. ACR_DDTS_COMPONENT "If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-6- ACRPVCENABLE 6-Information PVC Enable failed for VCD= [dec] on [chars] interface of ACR interface [chars]. PVC enable attempt failed on ACR physical interface. ACR_DDTS_COMPONENT "If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-6- ACRVPADD 6-Information VP creation failed for VPI= [dec] on [chars] interface of ACR group [chars]. VP creation attempt failed on ACR physical interface. ACR_DDTS_COMPONENT "If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ACR-6- ACRVPDEL 6-Information PVC deletion failed for VPI= [dec] on [chars] interface of ACR group [chars]. VP deletion attempt failed on ACR physical interface. ACR_DDTS_COMPONENT "If message is seen continuously get the output of \"show acr group \" \n\ and \"show acr group <> detail\" " "Copy the message exactly as it appears and report it to your technical " "support representative." ADDR_PROC-4-LCON 4-Warning ERRMSG_NOFLAGS - - - ADDR_PROC-4-LCON 4-Warning ERRMSG_NOFLAGS - - - ADDRQ-4-LCON 4-Warning ERRMSG_NOFLAGS - - - ADDRQ-4-LCON 4-Warning ERRMSG_NOFLAGS - - - ADJ_WALK_ERR-2-MPLS_TE 2-Critical ERRMSG_FLAG_TRACEBACK - - - ADJ_WALK_ERR-2-MPLS_TE 2-Critical ERRMSG_FLAG_TRACEBACK - - - ADJ-3-ADJ_XKEYS 3-Error Adj extended keys error [chars]: [chars] An initialization error occurred for extended keys. - LOG_STD_ACTION ADJ-3-ADJ_XKEYS 3-Error Adj extended keys error [chars]: [chars] An initialization error occurred for extended keys. - LOG_STD_ACTION ADJ-3-ADJGENALLOCATEFAIL 3-Error Failed to allocate memory [chars] An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ADJGENALLOCATEFAIL 3-Error Failed to allocate memory [chars] An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ADJGENDEALLOCATEFAIL 3-Error Failed to deallocate memory [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJGENDEALLOCATEFAIL 3-Error Failed to deallocate memory [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJMGRALLOCATEFAIL 3-Error Failed to allocate an adjacency summary event block An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ADJMGRALLOCATEFAIL 3-Error Failed to allocate an adjacency summary event block An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ADJMGRDISPATCHFAIL 3-Error Failed to enqueue an adjacency summary event block An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJMGRDISPATCHFAIL 3-Error Failed to enqueue an adjacency summary event block An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJMGRREFRESHFAIL 3-Error Failed to dispatch a refresh adjacency summary event An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJMGRREFRESHFAIL 3-Error Failed to dispatch a refresh adjacency summary event An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJSTACK2 3-Error Adj stack2 error [chars]: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ADJSTACK2 3-Error Adj stack2 error [chars]: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ALLOCATEFAIL 3-Error Failed to allocate an adjacency An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ALLOCATEFAIL 3-Error Failed to allocate an adjacency An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ALLOCATEONDOWN 3-Error Allocating adj when adj subsystem down An internal software error occurred. - LOG_STD_ACTION ADJ-3-ALLOCATEONDOWN 3-Error Allocating adj when adj subsystem down An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADADDRLEN 3-Error Zero address length detected distributing adj [chars] An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADADDRLEN 3-Error Zero address length detected distributing adj [chars] An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADADDRTYPE 3-Error Using an unsupported address type [dec] when trying to add/delete/modify/find an adjacency An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADADDRTYPE 3-Error Using an unsupported address type [dec] when trying to add/delete/modify/find an adjacency An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADLINKTYPE 3-Error Using an unsupported linktype [chars] when trying to add/delete/modify/find an adjacency An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADLINKTYPE 3-Error Using an unsupported linktype [chars] when trying to add/delete/modify/find an adjacency An internal software error occurred. An attempt to reference an adjacency with an unsupported address type has been made. - LOG_STD_ACTION ADJ-3-BADMACALIGN 3-Error adjacency mac string end [hec] not [chars] aligned An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADMACALIGN 3-Error adjacency mac string end [hec] not [chars] aligned An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADMACALIGN2 3-Error Adjacency mac string for [chars] not byte aligned offset [hec] length [hec] An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADMACALIGN2 3-Error Adjacency mac string for [chars] not byte aligned offset [hec] length [hec] An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADMAGIC 3-Error adjacency [chars] is followed by bad magic An internal software error occurred. - LOG_STD_ACTION ADJ-3-BADMAGIC 3-Error adjacency [chars] is followed by bad magic An internal software error occurred. - LOG_STD_ACTION ADJ-3-BOARDENCAP 3-Error Generation of encapsulation string for [chars] failed An internal software error occurred. - LOG_STD_ACTION ADJ-3-BOARDENCAP 3-Error Generation of encapsulation string for [chars] failed An internal software error occurred. - LOG_STD_ACTION ADJ-3-BROKERINITFAIL 3-Error Failed to initialise adjacency RP broker facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-BROKERINITFAIL 3-Error Failed to initialise adjacency RP broker facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-BUNDLES 3-Error Adj bundles: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-BUNDLES 3-Error Adj bundles: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-CONNID_INCOMPATIBLE_ID 3-Error Connection id [dec] could not be transformed: [chars] A connection id could not be transformed from a lower revision. - LOG_STD_ACTION ADJ-3-CONNID_INCOMPATIBLE_ID 3-Error Connection id [dec] could not be transformed: [chars] A connection id could not be transformed from a lower revision. - LOG_STD_ACTION ADJ-3-CONNID_INVALID 3-Error Connection id [dec] not recognized [chars] A supplied connection id did not exist in the managed id database. - LOG_STD_ACTION ADJ-3-CONNID_INVALID 3-Error Connection id [dec] not recognized [chars] A supplied connection id did not exist in the managed id database. - LOG_STD_ACTION ADJ-3-CONNID_INVALID_KEY 3-Error Unexpected connection-id parameter: Expecting [chars] when encoding [chars] An application has provided an invalid key for computing a connection-id. - LOG_STD_ACTION ADJ-3-CONNID_INVALID_KEY 3-Error Unexpected connection-id parameter: Expecting [chars] when encoding [chars] An application has provided an invalid key for computing a connection-id. - LOG_STD_ACTION ADJ-3-CONNID_POOL_EXHAUSTED 3-Error Pool of connection ids is fully utilized. It may not be possible to encode new sets of extended keys. Either there are too many unique sets of extended keys in the system or ids have been leaking. - LOG_STD_ACTION ADJ-3-CONNID_POOL_EXHAUSTED 3-Error Pool of connection ids is fully utilized. It may not be possible to encode new sets of extended keys. Either there are too many unique sets of extended keys in the system or ids have been leaking. - LOG_STD_ACTION ADJ-3-CONNID_TREE_MISMATCH 3-Error Supplied connid [dec] and extended keys [chars] do not match An adjacency has a connection id and extended keys mapping that doesn't match what's in the managed connection id database. This will likely result in a rejected adjacency update or sync. - LOG_STD_ACTION ADJ-3-CONNID_TREE_MISMATCH 3-Error Supplied connid [dec] and extended keys [chars] do not match An adjacency has a connection id and extended keys mapping that doesn't match what's in the managed connection id database. This will likely result in a rejected adjacency update or sync. - LOG_STD_ACTION ADJ-3-CONNID_TREE_OP_FAIL 3-Error Tree [chars] failed for [chars] for id [dec] connid [dec] A tree operation failed for the connection-id manager. An inability to correctly construct a tree will have negative consequences for the system. - LOG_STD_ACTION ADJ-3-CONNID_TREE_OP_FAIL 3-Error Tree [chars] failed for [chars] for id [dec] connid [dec] A tree operation failed for the connection-id manager. An inability to correctly construct a tree will have negative consequences for the system. - LOG_STD_ACTION ADJ-3-DBGFILTERALLOCATEFAIL 3-Error Failed to allocate an adjacency debug filter block An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-DBGFILTERALLOCATEFAIL 3-Error Failed to allocate an adjacency debug filter block An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ILALLOCATEFAIL 3-Error Failed to allocate an adjacency interest list subblock An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ILALLOCATEFAIL 3-Error Failed to allocate an adjacency interest list subblock An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ILDEALLOCATEFAIL 3-Error Failed to deallocate an adjacency interest list subblock An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ILDEALLOCATEFAIL 3-Error Failed to deallocate an adjacency interest list subblock An internal software error occurred. This is probably because not enough memory was available. - LOG_STD_ACTION ADJ-3-ILINITFAIL 3-Error Failed to initialise adjacency interest list facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-ILINITFAIL 3-Error Failed to initialise adjacency interest list facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-ILLEGALARGS 3-Error Illegal arguments - [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ILLEGALARGS 3-Error Illegal arguments - [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-ISSU_REG 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] ISSU negotiation failed for this XDR client. - "This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it." ADJ-3-ISSU_REG 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] ISSU negotiation failed for this XDR client. - "This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it." ADJ-3-LCXDRCLIENT 3-Error Adjacency distribution client: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-LCXDRCLIENT 3-Error Adjacency distribution client: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-MACOVERFLOW 3-Error Adjacency mac address for [chars] overflowed by [dec] bytes An internal software error occurred. - LOG_STD_ACTION ADJ-3-MACOVERFLOW 3-Error Adjacency mac address for [chars] overflowed by [dec] bytes An internal software error occurred. - LOG_STD_ACTION ADJ-3-MACSTRING_PD_ERROR 3-Error Platform request for header type [chars] from adjacency [chars] [chars][chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-MACSTRING_PD_ERROR 3-Error Platform request for header type [chars] from adjacency [chars] [chars][chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-NOFIBIDB 3-Error CEF Interface not found - [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-NOFIBIDB 3-Error CEF Interface not found - [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-RPXDRCLIENT 3-Error Adjacency distribution client: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-RPXDRCLIENT 3-Error Adjacency distribution client: [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-SBINITFAIL 3-Error Failed to initialise adjacency subblock facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-SBINITFAIL 3-Error Failed to initialise adjacency subblock facility An internal software error occurred. - LOG_STD_ACTION ADJ-3-STATETRANSITION 3-Error Unexpected state transition from [chars] to [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-STATETRANSITION 3-Error Unexpected state transition from [chars] to [chars] An internal software error occurred. - LOG_STD_ACTION ADJ-3-XKEYS_XDR_LEN 3-Error Expected [dec] bytes of extended adjacency keys: decoded [dec] bytes The XDR message was incorrectly formatted and may contain bad xkey data. - LOG_STD_ACTION ADJ-3-XKEYS_XDR_LEN 3-Error Expected [dec] bytes of extended adjacency keys: decoded [dec] bytes The XDR message was incorrectly formatted and may contain bad xkey data. - LOG_STD_ACTION ADJ-5-ADJISSUINCOMPATIBLE 5-Notice All or part of adjacency message for [chars] not sent to incompatible CEF instance for [chars] The adjacency is not distributed in whole to the remote CEF instance. This may impact traffic forwarding on remote CEF instance - LOG_STD_NO_ACTION ADJ-5-ADJISSUINCOMPATIBLE 5-Notice All or part of adjacency message for [chars] not sent to incompatible CEF instance for [chars] The adjacency is not distributed in whole to the remote CEF instance. This may impact traffic forwarding on remote CEF instance - LOG_STD_NO_ACTION ADJ-5-PARENT 5-Notice Midchain parent maintenance for [chars] - [chars] A midchain adjacency failed to stack onto output chain because a loop was detected. Traffic through the adjacency will be dropped until the adj is restacked. This condition is typically transient and is rectified by the control plane driving stacking. E.g. if an ip tunnel destination resolves through the tunnel transiently this message would appear. The situation would be rectified either by learning the tunnel destination through an interface other than the tunnel itself or by bringing the tunnel down. Monitor 'show adjacency internal' to determine if the problem has been resolved. - LOG_STD_NO_ACTION ADJ-5-PARENT 5-Notice Midchain parent maintenance for [chars] - [chars] A midchain adjacency failed to stack onto output chain because a loop was detected. Traffic through the adjacency will be dropped until the adj is restacked. This condition is typically transient and is rectified by the control plane driving stacking. E.g. if an ip tunnel destination resolves through the tunnel transiently this message would appear. The situation would be rectified either by learning the tunnel destination through an interface other than the tunnel itself or by bringing the tunnel down. Monitor 'show adjacency internal' to determine if the problem has been resolved. - LOG_STD_NO_ACTION ADJ-5-RESOLVE_REQ_FAIL 5-Notice Adj resolve request failed for [chars] on [chars] The source e.g. ARP or ND could not resolve the address. - LOG_STD_ACTION ADJ-5-RESOLVE_REQ_FAIL 5-Notice Adj resolve request failed for [chars] on [chars] The source e.g. ARP or ND could not resolve the address. - LOG_STD_ACTION ADV-4-LDP 4-Warning ERRMSG_NOFLAGS - - - ADV-4-LDP 4-Warning ERRMSG_NOFLAGS - - - AGGMGR-0-NO_SPACE 0-Emergency No space left for creator \[chars]\ to add data item to agg list items [dec] max [dec] remaining [dec] An attempt was made to add an item to an aggregation list that had just been successfully created but for some reason the add failed. This situation should never occur. If it does occur then it is the result of a program error which would be found during development and considered an internal error. There is no work around. cosmos LOG_STD_ACTION AIP-3-AIPFAILSETUPVC 3-Error [chars] Failed to setup vc [dec] Cause: [chars] - - - AIP-3-AIPFAILSETUPVCAVG 3-Error Interface [chars] Failed to setup vc [dec] Cause: [chars] Expected range [[dec] .. [dec]]Kbps for AIP Average Rate Metering. Average Rate=Peak Rate= [dec] Kbps turns Average Rate Metering OFF A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION ALARM_PERSISTENCY-3-ALARM_CHUNK_INFO_FAIL 3-Error [chars] Failed to create the chunk-pool for the persistent alarm info asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_CHUNK_QUEUE_FAIL 3-Error [chars] Failed to create the chunk-pool for the persistent alarm queue asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_CHUNK_DESTROY_FAIL 3-Error Failed to destroy [chars] chunk pool Failed to destroy a chunk pool asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_FILE_CREATE_ERROR 3-Error Failed to create [chars]/[chars] file error:[chars] Failed to create persistent_alarm_log file asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_FILE_OPEN_ERROR 3-Error Failed to open [chars]/[chars] file error:[chars] Failed to open persistent_alarm_log file asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_FILE_WRITE_ERROR 3-Error Failed to write to [chars]/[chars] file actual:[dec] written:[dec] error:[chars] Failed to open persistent_alarm_log file asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_NULL 3-Error Persistent alarm queue alarm info is NULL alarm_info of the persistence queue is NULL asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_INFO_PROCESS_FAIL 3-Error Failed to create mcprp_spa_persistence_logger process Failed to create mcprp_spa_persistence_logger process asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_PROFILE_NULL 3-Error [chars] Alarm profile is enabled with a wrong profile name - LOG_STD_ACTION ALARM_PERSISTENCY-3-ALARM_QUEUE_NULL 3-Error Persistent alarm queue info is NULL alarm_info of the persistence queue is NULL asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-3-NULL_DATA_STRUCTURE 3-Error [chars] is NULL Data-structure is NULL asr900-lotr-im LOG_STD_ACTION ALARM_PERSISTENCY-6-ALARM_CHUNK_INFO_CREATED 6-Information [chars] Created the chunk-pool for the persistenct alarm info - LOG_STD_NO_ACTION ALARM_PERSISTENCY-6-ALARM_CHUNK_QUEUE_CREATED 6-Information [chars] Created the chunk-pool for the persistent alarm queue - LOG_STD_NO_ACTION ALARM_PERSISTENCY-6-ALARM_INFO_FILE_CREATED 6-Information Successfully created [chars]/[chars] file Successfully created alarm_persistency file - LOG_STD_NO_ACTION ALARM_PERSISTENCY-6-ALARM_INFO_FILE_ROTATED 6-Information Switching to [chars] file \nafter writing [dec] records to [chars] file Switched to other file after reaching a specified limit - LOG_STD_NO_ACTION ALARM_PERSISTENCY-6-ALARM_INFO_PROCESS_CREATE 6-Information created mcprp_spa_persistence_logger process:[dec] Created mcprp_spa_persistence_logger process - LOG_STD_NO_ACTION ALARM_PERSISTENCY-6-ALARM_RECORDS_FULL 6-Information Persistent alarm info queue is full with [dec] elements persistent alarm_records in the persistence queue are full - LOG_STD_NO_ACTION ALARM-3-CLEAR 3-Error [chars] [chars] [chars] [chars] [chars] - - "" ALARM-3-CLEAR 3-Error [chars] [chars] [chars] [chars] [chars] - - "" ALARM-3-NOMEM 3-Error OUT of Memory: [chars] - - "" ALARM-3-NOMEM 3-Error OUT of Memory: [chars] - - "" ALARM-6-DEFAULT_ALARM_PROFILE 6-Information [chars] Telcordia profile enable or disable information - LOG_STD_NO_ACTION ALARM-6-ENTITY_INFO 6-Information [chars] [chars] [chars] [chars] [chars] Entity alarm assertion or deassertion information. - LOG_STD_NO_ACTION ALARM-6-ENTITY_INFO 6-Information [chars] [chars] [chars] [chars] [chars] Entity alarm assertion or deassertion information. - LOG_STD_NO_ACTION ALG_COM-3-ALG_COND_DEBUG_REG_FAILED 3-Error [chars] - - - ALG_COM-3-ALG_REGISTER_FAILED 3-Error [dec] ALG registration failed. cpp-ucode LOG_STD_ACTION ALG_COM-3-CHUNK_CREATE_FAIL 3-Error [chars] A request to create a chunk failed cpp-ucode LOG_STD_ACTION ALG_COM-3-CHUNK_EXTEND_FAIL 3-Error [chars] A request to create a chunk failed cpp-ucode LOG_STD_ACTION ALG_COM-3-IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION ALG_PROXY-3-PROXY_IPC_FAIL 3-Error rc= [dec] The ALG proxy has experienced a failure when trying to send an IPC cpp-ucode LOG_STD_ACTION ALG_PROXY-3-PROXY_MEM_EXTEND_FAILED 3-Error ALG IPC subtype: [dec] Extending memory failed. cpp-ucode LOG_STD_ACTION ALG_PROXY-3-PROXY_MEM_REQ_FAILED 3-Error ALG IPC subtype: [dec] Requesting more memory failed. cpp-ucode LOG_STD_ACTION ALG_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [dec] Invalid IPC message subtype. cpp-ucode LOG_STD_ACTION ALG_PROXY-4-PROXY_IPC_INVALID_MSG_LEN 4-Warning [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length. cpp-ucode LOG_STD_ACTION ALG-3-ALG_REGISTRY_RC 3-Error An ALG registry call failed with rc[chars] The return code from an ALG registry call indicates an\n\ error. alg LOG_STD_ACTION ALG-3-API_FAILED 3-Error NULL A call to the API of another component has indicated an\n\ error. alg LOG_STD_ACTION ALG-3-BAD_MAGIC 3-Error Invalid magic number%#10x An internal data structure is corrupt. alg LOG_STD_ACTION ALG-3-EEXIST 3-Error NULL An item unexpectedly exists already. alg LOG_STD_ACTION ALG-3-EINVAL 3-Error NULL An unexpected input value to a function was incorrect alg LOG_STD_ACTION ALG-3-ENOENT 3-Error NULL A lookup failed unexpectedly. alg LOG_STD_ACTION ALG-3-ENOMEM 3-Error Memory allocation failed An attempt to allocae memory has failed. alg LOG_STD_ACTION ALG-3-INIT_FAILED 3-Error An initialization failed rc[chars] - - - ALG-3-RUNAWAY_LOOP 3-Error NULL A loop has exceeded the expected number of iterations. alg LOG_STD_ACTION ALG-3-UNINITIALIZED 3-Error ALG feature is not properly initialized A function call was made when the system was not properly\n\ initialized. alg LOG_STD_ACTION ALIGN-3-CORRECT 3-Error Alignment correction made at [chars] [chars]ing 0x[hec] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-CORRECT 3-Error Alignment correction made at 0x[hec] [chars]ing 0x[hec] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-CORRECT 3-Error Alignment correction made at [chars] [chars]ing 0x[hec] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-CORRECT 3-Error Alignment correction made at 0x[hec] [chars]ing 0x[hec] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-CORRECT_SO 3-Error Alignment correction made at [chars] [chars]ing [chars] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-CORRECT_SO 3-Error Alignment correction made at [chars] [chars]ing [chars] A software component within the router needs memory optimization. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-FULL 3-Error Alignment log is full - no new entries will be recorded The router identified more software components in need of memory\n\ optimization than it can record. cpu "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-FULL 3-Error Alignment log is full - no new entries will be recorded The router identified more software components in need of memory\n\ optimization than it can record. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-FULL 3-Error Alignment log is full - no new entries will be recorded The router identified more software components in need of memory\n\ optimization than it can record. cpu "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-FULL 3-Error Alignment log is full - no new entries will be recorded The router identified more software components in need of memory\n\ optimization than it can record. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-READEXCEPTION 3-Error Warning : read accees failed at [chars] still continuing \n In ls1010 read access failures do not make the box reload. They can \n\ be caused by either a bad register value in the asp ver 3.3 or earlier\n\ or a real problem in the hardware - "If the ASP version is 3.3 or more report it to your\n\ technical support representative." ALIGN-3-READEXCEPTION 3-Error Warning : read accees failed at [chars] still continuing \n In ls1010 read access failures do not make the box reload. They can \n\ be caused by either a bad register value in the asp ver 3.3 or earlier\n\ or a real problem in the hardware - "If the ASP version is 3.3 or more report it to your\n\ technical support representative." ALIGN-3-RO_WRITE 3-Error Spurious memory access made at [chars] writing to 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. cpu "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-RO_WRITE 3-Error Spurious memory access made at [chars] writing to 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. cpu "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at [chars] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. cpu "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at [chars] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at 0x[hec] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at [chars] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. cpu "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at [chars] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at 0x[hec] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS 3-Error Spurious memory access made at [chars] reading 0x[hec] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS_SO 3-Error Spurious memory access made at [chars] reading [chars] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-SPURIOUS_SO 3-Error Spurious memory access made at [chars] reading [chars] An attempted but illegal access to a low memory address within a software component in the router has been temporarily blocked. - "Copy the error message exactly as it appears on the console or in the " "system log. Issue the show alignment command to " "gather data that may help identify the nature of the error. If you " "cannot determine the nature of the error from the error message text " "or from the show alignment output call your " "Cisco technical support representative and provide the representative " "with the gathered information." ALIGN-3-TRACE 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. cpu "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= %08x %08x %08x %08x %08x %08x %08x %08x A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. cpu "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= %08x %08x %08x %08x %08x %08x %08x %08x A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE_SO 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACE_SO 3-Error -Traceback= [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACEX 3-Error [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACEX 3-Error [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACEX 3-Error [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALIGN-3-TRACEX 3-Error [chars] A trace that shows where the previous ALIGN error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." ALLOC-3-ICPM 3-Error ERRMSG_NOFLAGS - - - ALLOC-3-ICPM 3-Error ERRMSG_NOFLAGS - - - ALLOC-3-LCON 3-Error ERRMSG_NOFLAGS - - - ALLOC-3-LCON 3-Error ERRMSG_NOFLAGS - - - ALPS-3-ALPSFAIL 3-Error ALPS: Assertion failed: [chars] An internal software error has occurred. - LOG_STD_ACTION ALPS-3-ASCU_FSM_ERR 3-Error ASCU %02x on interface [chars] has an internal FSM error. Internal error. - "Turn debug flags on capture traces & contact Cisco technical support" ALPS-3-ASCU_IF_STUCK 3-Error Polling for ASCU %02x on interface [chars] is stalled. The polling mechanism for an ALPS interface has become stuck. - LOG_STD_NO_ACTION ALPS-5-ASCU_DISABLED_ASCU_STUCK 5-Notice ASCU %02x on interface [chars] has been disabled since 4 consecutive messages were received from same SID. An ALPS ASCU has been automatically disabled. - LOG_STD_NO_ACTION ALPS-5-ASCU_DOWN 5-Notice ASCU %02x on interface [chars] is down. An ALPS ASCU has transitioned from up to down. - LOG_STD_NO_ACTION ALPS-5-ASCU_UP 5-Notice ASCU %02x on interface [chars] is up. An ALPS ASCU has transitioned from down to up. - LOG_STD_NO_ACTION ALPS-5-CIRCUIT_CLOSED 5-Notice Circuit [chars] changed state to closed rsn = [chars]. An ALPS circuit has tranistioned from open to closed - LOG_STD_NO_ACTION ALPS-5-CIRCUIT_OPEN 5-Notice Circuit [chars] changed state to open. An ALPS circuit has transitioned from closed to open. - LOG_STD_NO_ACTION ALPS-5-PEER_CLOSED 5-Notice Peer [inet] [chars] changed state to closed. An ALPS peer connection is now closed. - LOG_STD_NO_ACTION ALPS-5-PEER_CLOSED_DYNAMIC_INACTIVITY 5-Notice Peer [inet] [chars] closed due to inactivity. An ALPS peer connection is now closed due to inactivity. - LOG_STD_NO_ACTION ALPS-5-PEER_CONN_ID_CHANGE 5-Notice Peer [inet] [chars] ID modified to [inet] [chars]. An ALPS peer connection identifier has changed. - LOG_STD_NO_ACTION ALPS-5-PEER_OPEN 5-Notice Peer [inet] [chars] changed state to open. An ALPS peer connection is now open. - LOG_STD_NO_ACTION ALPS-6-CIRCUIT_ASCU_REJECT 6-Information Circuit [chars] received a Circuit Open Confirm with a list of rejected ascus An ALPS circuit sent a Circuit Open Request message and\n\ received a Circuit Open Confirm with a list of rejected ascus. - LOG_STD_NO_ACTION ALPS-6-CIRCUIT_BUSY_START 6-Information Circuit [chars] has entered a congested state. An ALPS circuit is experiencing congestion. - LOG_STD_NO_ACTION ALPS-6-CIRCUIT_OPEN_FAILED 6-Information Circuit [chars] received a Circuit Open Failed message rsn = [chars]. An ALPS circuit sent a Circuit Open Request message and\n\ received a Circuit Open Failed message as a reply. - LOG_STD_NO_ACTION ALPS-6-CIRCUIT_UPDATE_FAILED 6-Information Circuit [chars] received a Circuit Open Failed message rsn = [chars]. An ALPS circuit sent a Circuit Update message and\n\ received a Circuit Open Failed message as a reply. - LOG_STD_NO_ACTION ALPS-6-CIRCUIT_X25_VC_STUCK 6-Information Host unresponsive on X.25 VC for circuit [chars] The X.25 or EMTOX host is not advancing the transmit window\n\ for extended periods of time. This may be indicative of a\n\ temporary problem with the host application. An X.25 Reset \n\ is sent to reset the transmit and receive windows to\n\ allow communication to proceed. - "None" ALPS-6-PEER_BUSY_END 6-Information Peer [inet] [chars] has exited a congested state. An ALPS peer connection is no longer experiencing congestion. - LOG_STD_NO_ACTION ALPS-6-PEER_BUSY_START 6-Information Peer [inet] [chars] has entered a congested state. An ALPS peer connection is experiencing congestion. - LOG_STD_NO_ACTION ALPS-6-PEER_OPEN_FAIL 6-Information Peer [inet] [chars] open failed rsn = [chars] An ALPS peer connection attempted to open but failed to open. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_BUSY_END 7-Debug Circuit [chars] has exited a congested state. An ALPS circuit is no longer experiencing congestion. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_DROPS_CKT_DISABLED 7-Debug Threshold exceeded for circuit disabled drops for circuit [chars] The number of ALPS circuit drops due to circuit disabled \n\ exceeds the ALPS circuit threshold value. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_DROPS_INVALID_ASCU 7-Debug Threshold exceeded for invalid ASCU drops for circuit [chars] The number of ALPS circuit drops due to invalid ASCU identifier \n\ exceeds the ALPS circuit threshold value. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_DROPS_LIFETIME_EXPIRED 7-Debug Threshold exceeded for lifetime timer expiration drops for circuit [chars] The number of ALPS circuit drops due to lifetime timer \n\ expiration exceeds the ALPS circuit threshold value. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_DROPS_QUEUE_OVERFLOW 7-Debug Threshold exceeded for queue overflow drops for circuit [chars] The number of ALPS circuit drops due to queue overflow \n\ exceeds the ALPS circuit threshold value. - LOG_STD_NO_ACTION ALPS-7-CIRCUIT_DROPS_VC_RESET 7-Debug Threshold exceeded for X.25 VC Reset drops for circuit [chars] The number of ALPS circuit drops due to X.25 VC Reset \n\ exceeds the ALPS circuit threshold value. - LOG_STD_NO_ACTION ALPS-7-PEER_DROPS_MAX_SIZE_EXCEEDED 7-Debug Threshold exceeded for maximum size exceeded drops for peer [inet] [chars]. - - - ALPS-7-PEER_DROPS_PEER_UNREACHABLE 7-Debug Threshold exceeded for peer unreachable peer drops for peer [inet] [chars]. - - - ALPS-7-PEER_DROPS_QUEUE_OVERFLOW 7-Debug Threshold exceeded for TCP Queue overflow peer drops for peer [inet] [chars]. - - - ALPS-7-PEER_DROPS_VERSION_MISMATCH 7-Debug Threshold exceeded for version mismatch peer drops for peer [inet] [chars]. - - - AMD79C971_FE-5-FAILED_SUSPEND 5-Notice Failed to suspend the amd79c971 chip Failed to suspend the amd79c971 chip Mid-Ethernet LOG_STD_ACTION AMDP2_FE-1-DISCOVER 1-Alert Only found [dec] interfaces on bay [dec] shutting down bay The software could not identify the interface card. pas-ethernet "Power down reseat the interface card " "and reboot. If the message recurs call your " "technical support representative for assistance." AMDP2_FE-1-INITFAIL 1-Alert [chars] CSR[dec]=0x%04x The software failed to initialize/restart an Ethernet/Fast Ethernet interface. pas-ethernet "Try resetting the interface by doing a shutdown followed by " "a no shutdown. If the message recurs try reseating the Port " "Adaptor. If reseating also does not work call your technical " "support representative for assistance." AMDP2_FE-1-MEMERR 1-Alert [chars] CSR[dec]=0x%04x The interface could not access system resources for a long time. This problem may occur under very heavy loads. pas-ethernet "The system should recover. No action is required. If the message " "recurs call your technical support representative for assistance." AMDP2_FE-1-NOMII 1-Alert [chars] MII transceiver not connected The MII transceiver was disconnected while the MII port was selected. pas-ethernet "Connect the transceiver and enter the " "shut and no shut commands for the " "interface in the configuration menu." AMDP2_FE-1-NOTSUPPORTED 1-Alert 2FE PA not supported on NPE100 shutting down bay 2FE PA is not supported on a 7200 with NPE100. pas-ethernet "NPE150 or better is needed for 2FE PA." AMDP2_FE-2-NOISL 2-Critical [chars] hardware does not support ISL The interface cannot be configured as an ISL trunk. pas-ethernet "Check the configuration." AMDP2_FE-3-NOTAMDP2 3-Error Slot [dec] device ID seen as [hex] expected [hex] The software could not recognize the interface chips. pas-ethernet "Power down reseat the interface card and " "reboot. If the message recurs call your " "technical support representative for assistance." AMDP2_FE-3-OWNERR 3-Error [chars] packet buffer pak=0x[hec] The software detected an error in descriptor ownership. pas-ethernet "Try a later version of the software. If the message " "recurs call your technical support representative " "for assistance." AMDP2_FE-3-SPURIDON 3-Error [chars] spurious chip init CSR[dec]=0x%04x An illegal condition indicating initialization done has occurred. pas-ethernet "Clear the interface. " "If this message recurs call your technical support " "representative for assistance." AMDP2_FE-3-TOOMANYPART 3-Error Bad packet with [dec] particles pak=0x[hec] The software detected an invalid packet. pas-ethernet "Try a later version of the software. If the message " "recurs call your technical support representative " "for assistance." AMDP2_FE-3-UNDERFLO 3-Error [chars] transmit error While transmitting a frame the controller chip's local buffer received insufficient data because data could not be transferred to the chip fast enough to keep pace with its output rate. Normally such a problem is temporary depending on transient peak loads within the system. pas-ethernet "The system should recover. No action is required." AMDP2_FE-4-BABBLE 4-Warning [chars] transmit problem CSR0=[hex] The transmitter has been on the channel longer than the time taken to transmit the largest frame pas-ethernet "The system should recover. No action is required." AMDP2_FE-5-LATECOLL 5-Notice [chars] transmit error Late collisions occurred on the Ethernet/Fast Ethernet interface. When a collision occurs after the preamble has been transmitted then such a collision is called a LATE collision. The packet will be retransmitted but this condition could also indicate that another device is failing to detect when the network is in use. pas-ethernet "If the interface is Fast Ethernet verify that both " "peers are in the same duplex mode. For regular " "Ethernet the system should recover. No action is " "required." AMDP2_FE-5-LOSTCARR 5-Notice [chars] cable/transceiver problem? The cable and/or transceiver is not connected. pas-ethernet "Connect the cable and/or transceiver." AMDP2_FE-6-EXCESSCOLL 6-Information [chars] TDR=[dec] TRC=[dec] Ethernet/Fast Ethernet is seeing multiple collisions. This may occur under heavy loads. pas-ethernet "The system should recover. No action is " "required." AMT-2-ADD_GATEWAY 2-Critical Error adding new Gateway Can't get memory for a new Gateway [chars] port [dec] - LOG_STD_NO_ACTION AMT-2-ADD_GATEWAY 2-Critical Error adding new Gateway Can't get memory for a new Gateway [chars] port [dec] - LOG_STD_NO_ACTION AMT-2-GATEWAY_INIT 2-Critical Error initializing AMT Gateway Insufficient memory is available to initialize Gateway - LOG_STD_SH_TECH_ACTION AMT-2-GATEWAY_INIT 2-Critical Error initializing AMT Gateway Insufficient memory is available to initialize Gateway - LOG_STD_SH_TECH_ACTION AMT-2-MSGTYPE_ERR 2-Critical [chars] AMT message with invalid type [dec] AMT type is not 1-7 - LOG_STD_NO_ACTION AMT-2-MSGTYPE_ERR 2-Critical [chars] AMT message with invalid type [dec] AMT type is not 1-7 - LOG_STD_NO_ACTION AMT-2-PROCESS_ERR 2-Critical Error initializing AMT process Can't start the AMT process - LOG_STD_NO_ACTION AMT-2-PROCESS_ERR 2-Critical Error initializing AMT process Can't start the AMT process - LOG_STD_NO_ACTION AMT-2-RELAY_INIT 2-Critical Error initializing AMT Relay Insufficient memory is available to initialize Relay - LOG_STD_SH_TECH_ACTION AMT-2-RELAY_INIT 2-Critical Error initializing AMT Relay Insufficient memory is available to initialize Relay - LOG_STD_SH_TECH_ACTION AMT-2-RPT_WAVLINIT 2-Critical Error initializing IGMP Unsolicited Report handler Insufficient memory is available to initialize the IGMP \n\ Unsolicited Report handler. - LOG_STD_SH_TECH_ACTION AMT-2-RPT_WAVLINIT 2-Critical Error initializing IGMP Unsolicited Report handler Insufficient memory is available to initialize the IGMP \n\ Unsolicited Report handler. - LOG_STD_SH_TECH_ACTION AN-3-ACP_CHANNEL_TO_NBR_FAILED 3-Error Failed to create ACP [chars] from Device Addr [chars] Autonomic Network Control Plane Channel has not been created to the neighbor AN LOG_STD_NO_ACTION AN-3-ACP_CHANNEL_TO_NBR_FAILED 3-Error Failed to create ACP [chars] from Device Addr [chars] Autonomic Network Control Plane Channel has not been created to the neighbor AN LOG_STD_NO_ACTION AN-3-ACP_DIKE_TO_NBR_FAILED 3-Error Failed to create DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - Failed to create DIKE tunnel to neighbor AN LOG_STD_NO_ACTION AN-3-ACP_DIKE_TO_NBR_FAILED 3-Error Failed to create DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - Failed to create DIKE tunnel to neighbor AN LOG_STD_NO_ACTION AN-3-ACP_IPSEC_TO_NBR_FAILED 3-Error Failed to create IPSEC on ACP from device Addr [chars] Autonomic Network Control plane - Failed to create IPSEC tunnel to neighbor AN LOG_STD_NO_ACTION AN-3-ACP_IPSEC_TO_NBR_FAILED 3-Error Failed to create IPSEC on ACP from device Addr [chars] Autonomic Network Control plane - Failed to create IPSEC tunnel to neighbor AN LOG_STD_NO_ACTION AN-3-ACP_VRF_GLOBAL_CREATE_FAIL 3-Error Device UDI [chars] failed to create Autonomic network VRF has not been created globally AN LOG_STD_NO_ACTION AN-3-ACP_VRF_GLOBAL_CREATE_FAIL 3-Error Device UDI [chars] failed to create Autonomic network VRF has not been created globally AN LOG_STD_NO_ACTION AN-3-ACP_VRF_INTERFACE_CREATE_FAIL 3-Error Device UDI [chars] failed to create Autonomic VRF Autonomic network VRF has not been created on the interface AN LOG_STD_NO_ACTION AN-3-ACP_VRF_INTERFACE_CREATE_FAIL 3-Error Device UDI [chars] failed to create Autonomic VRF Autonomic network VRF has not been created on the interface AN LOG_STD_NO_ACTION AN-3-ANR_WHITELIST_FILE_ERROR 3-Error Autonomic Registrar with Addr [chars] encountered error in The autonomic registeration authority encountered file error when reading from whitelist file check the file name and its contents AN LOG_STD_NO_ACTION AN-3-ANR_WHITELIST_FILE_ERROR 3-Error Autonomic Registrar with Addr [chars] encountered error in The autonomic registeration authority encountered file error when reading from whitelist file check the file name and its contents AN LOG_STD_NO_ACTION AN-3-DOMAIN_KEY_GEN_FAIL 3-Error The bootstrapping device with key label [chars] The key pair generation failed at the device for triggering BS request message to Autonomic registrar. Can be due to failure in RSA key pair generation in the crypto library AN LOG_STD_NO_ACTION AN-3-DOMAIN_KEY_GEN_FAIL 3-Error The bootstrapping device with key label [chars] The key pair generation failed at the device for triggering BS request message to Autonomic registrar. Can be due to failure in RSA key pair generation in the crypto library AN LOG_STD_NO_ACTION AN-3-IDP_INTENT_FILE_ERROR 3-Error Device Addr [chars] encountered error [chars] when reading from The Intent Distribution Protocol Module encountered file error when reading from intent file check the file name and its contents AN LOG_STD_NO_ACTION AN-3-IDP_INTENT_FILE_ERROR 3-Error Device Addr [chars] encountered error [chars] when reading from The Intent Distribution Protocol Module encountered file error when reading from intent file check the file name and its contents AN LOG_STD_NO_ACTION AN-3-MSG_INVALID_HEADER 3-Error Invalid message header type [dec] received The message packet header got corrupted and invalid header received AN LOG_STD_NO_ACTION AN-3-MSG_INVALID_HEADER 3-Error Invalid message header type [dec] received The message packet header got corrupted and invalid header received AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_EXPIRED 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] has expired The domain certificate of the neighbor device has expired AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_EXPIRED 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] has expired The domain certificate of the neighbor device has expired AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_INVALID 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is invalid The domain certificate of the neighbor device is invalid AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_INVALID 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is invalid The domain certificate of the neighbor device is invalid AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_REVOKED 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is revoked The domain certificate of the neighbor device has been revoked AN LOG_STD_NO_ACTION AN-3-NBR_DOMAIN_CERT_REVOKED 3-Error Domain certificate of Neighbor with Addr [chars] connected on interface [chars] is revoked The domain certificate of the neighbor device has been revoked AN LOG_STD_NO_ACTION AN-3-TLV_PARSE_ALIGN_ERROR 3-Error TLV parsed Len [dec] Next TLV could be misaligned Parsed TLV message is not a multiple of 4 and the next TLV message can be misaligned AN LOG_STD_NO_ACTION AN-3-TLV_PARSE_ALIGN_ERROR 3-Error TLV parsed Len [dec] Next TLV could be misaligned Parsed TLV message is not a multiple of 4 and the next TLV message can be misaligned AN LOG_STD_NO_ACTION AN-3-TLV_PARSE_LEN_INCORRECT 3-Error TLV parsed len [dec] > original message length [dec] Parsed TLV message length is greater than original message length AN LOG_STD_NO_ACTION AN-3-TLV_PARSE_LEN_INCORRECT 3-Error TLV parsed len [dec] > original message length [dec] Parsed TLV message length is greater than original message length AN LOG_STD_NO_ACTION AN-4-ANR_SIGN_VERIFY_FAIL 4-Warning Device UDI [chars] signature verification of Autonomic registrar The new device joining the network verified the signature of autonomic registrar as a part of mutual authentication and the verification failed AN LOG_STD_NO_ACTION AN-4-ANR_SIGN_VERIFY_FAIL 4-Warning Device UDI [chars] signature verification of Autonomic registrar The new device joining the network verified the signature of autonomic registrar as a part of mutual authentication and the verification failed AN LOG_STD_NO_ACTION AN-4-DEVICE_ALREADY_REGISTERED_BY_ANR 4-Warning Device with UDI [chars] connected to Proxy Addr [chars] on interface [chars] is already registered by The autonomic network registration authority will not allow this device to join as it already registered with a different public key AN LOG_STD_NO_ACTION AN-4-DEVICE_ALREADY_REGISTERED_BY_ANR 4-Warning Device with UDI [chars] connected to Proxy Addr [chars] on interface [chars] is already registered by The autonomic network registration authority will not allow this device to join as it already registered with a different public key AN LOG_STD_NO_ACTION AN-4-DEVICE_NOT_IN_WHITELIST 4-Warning Device with UDI [chars] The autonomic network registration authority will not allow this device to join as it is not in whitelist AN LOG_STD_NO_ACTION AN-4-DEVICE_NOT_IN_WHITELIST 4-Warning Device with UDI [chars] The autonomic network registration authority will not allow this device to join as it is not in whitelist AN LOG_STD_NO_ACTION AN-4-MASA_AUDIT_LOG_FAIL 4-Warning Device with udi [chars] is not in the audit log of MASA The manufacturer authorised signing authority audit log doesnt contain this device in its database AN LOG_STD_NO_ACTION AN-4-MASA_AUDIT_LOG_FAIL 4-Warning Device with udi [chars] is not in the audit log of MASA The manufacturer authorised signing authority audit log doesnt contain this device in its database AN LOG_STD_NO_ACTION AN-4-MASA_AUTH_FAIL 4-Warning Device with udi [chars] is not authorized by MASA The MASA - manufacturer authorised signing authority has not authorised this device in its network AN LOG_STD_NO_ACTION AN-4-MASA_AUTH_FAIL 4-Warning Device with udi [chars] is not authorized by MASA The MASA - manufacturer authorised signing authority has not authorised this device in its network AN LOG_STD_NO_ACTION AN-4-MASA_AUTH_TOKEN_PARSE_ERROR 4-Warning Error while parsing authentication token from MASA server for device udi-[chars] Encountered error while parsing the authentication token response string from MASA server AN LOG_STD_NO_ACTION AN-4-MASA_AUTH_TOKEN_PARSE_ERROR 4-Warning Error while parsing authentication token from MASA server for device udi-[chars] Encountered error while parsing the authentication token response string from MASA server AN LOG_STD_NO_ACTION AN-5-ANR_DOWN 5-Notice Disabled autonomic registrar with Addr [chars] The autonomic network registration authority functionality is disabled AN LOG_STD_NO_ACTION AN-5-ANR_DOWN 5-Notice Disabled autonomic registrar with Addr [chars] The autonomic network registration authority functionality is disabled AN LOG_STD_NO_ACTION AN-5-ANR_UP 5-Notice A New Autonomic Registrar has been configured in domain [chars] and it has been assigned IP Addr [chars] The autonomic network registration authority has been confgiured and is locally up AN LOG_STD_NO_ACTION AN-5-ANR_UP 5-Notice A New Autonomic Registrar has been configured in domain [chars] and it has been assigned IP Addr [chars] The autonomic network registration authority has been confgiured and is locally up AN LOG_STD_NO_ACTION AN-5-CD_STATE_CHANGED 5-Notice [chars] Channel [dec] [chars] - Our Intf [chars] CD L2 or Reuse Channel Created/Removed/Expired AN LOG_STD_NO_ACTION AN-5-CD_STATE_CHANGED 5-Notice [chars] Channel [dec] [chars] - Our Intf [chars] CD L2 or Reuse Channel Created/Removed/Expired AN LOG_STD_NO_ACTION AN-5-DEVICE_BOOTSTRAPPED_BY_ANR 5-Notice Device with UDI [chars] and Addr [chars] has been boot strapped by autonomic registrar in autonomic domain [chars] The autonomic network registration authority has bootstrapped this device AN LOG_STD_NO_ACTION AN-5-DEVICE_BOOTSTRAPPED_BY_ANR 5-Notice Device with UDI [chars] and Addr [chars] has been boot strapped by autonomic registrar in autonomic domain [chars] The autonomic network registration authority has bootstrapped this device AN LOG_STD_NO_ACTION AN-5-IDP_INTENT_VER_OLD_DISCARD 5-Notice Device Addr [chars] discarded the older intent version [dec] The device received an old intent file by Intent Distribution Protocol and is discarding it AN LOG_STD_NO_ACTION AN-5-IDP_INTENT_VER_OLD_DISCARD 5-Notice Device Addr [chars] discarded the older intent version [dec] The device received an old intent file by Intent Distribution Protocol and is discarding it AN LOG_STD_NO_ACTION AN-5-IDP_INTENT_VER_UPDATED 5-Notice Device Addr [chars] updated to a new Intent version [dec] The device received a new intent file by Intent Distribution Protocol AN LOG_STD_NO_ACTION AN-5-IDP_INTENT_VER_UPDATED 5-Notice Device Addr [chars] updated to a new Intent version [dec] The device received a new intent file by Intent Distribution Protocol AN LOG_STD_NO_ACTION AN-5-NBR_ADDED 5-Notice Device with UDI [chars] is added as a Neighbor to Device with Addr [chars] on the interface [chars] A hello message is received and the device is added in the neighbor table AN LOG_STD_NO_ACTION AN-5-NBR_ADDED 5-Notice Device with UDI [chars] is added as a Neighbor to Device with Addr [chars] on the interface [chars] A hello message is received and the device is added in the neighbor table AN LOG_STD_NO_ACTION AN-5-NBR_IN_DOMAIN 5-Notice Neighbor with Addr [chars] connected via interface [chars] to device Addr [chars] is brought inside my domain [chars] The device has been admitted into the autonomic domain AN LOG_STD_NO_ACTION AN-5-NBR_IN_DOMAIN 5-Notice Neighbor with Addr [chars] connected via interface [chars] to device Addr [chars] is brought inside my domain [chars] The device has been admitted into the autonomic domain AN LOG_STD_NO_ACTION AN-5-NBR_LOST 5-Notice Device with ACP Addr [chars] lost connectivity to its Neighbor Addr [chars] on interface [chars] Lost connectivity to the neighboring device & it is no longer part of autonomic domain AN LOG_STD_NO_ACTION AN-5-NBR_LOST 5-Notice Device with ACP Addr [chars] lost connectivity to its Neighbor Addr [chars] on interface [chars] Lost connectivity to the neighboring device & it is no longer part of autonomic domain AN LOG_STD_NO_ACTION AN-5-NBR_OUT_DOMAIN 5-Notice Neighbor with Addr [chars] connected via interface [chars] The device is removed from the autonomic domain it can happen if the domain certificate is NULL or if the domain certificate is invalid AN LOG_STD_NO_ACTION AN-5-NBR_OUT_DOMAIN 5-Notice Neighbor with Addr [chars] connected via interface [chars] The device is removed from the autonomic domain it can happen if the domain certificate is NULL or if the domain certificate is invalid AN LOG_STD_NO_ACTION AN-5-SERVICE_LEARNT 5-Notice Device with Addr [chars] learnt Autonomic service with Service Type [dec] Service IP Addr [chars] - - - AN-5-SERVICE_LEARNT 5-Notice Device with Addr [chars] learnt Autonomic service with Service Type [dec] Service IP Addr [chars] - - - AN-6-ACP_CHANNEL_TO_NBR_CREATED 6-Information Established ACP [chars] from Device Addr [chars] to Autonomic Network Control plane Channel has been created to the neighbor AN LOG_STD_NO_ACTION AN-6-ACP_CHANNEL_TO_NBR_CREATED 6-Information Established ACP [chars] from Device Addr [chars] to Autonomic Network Control plane Channel has been created to the neighbor AN LOG_STD_NO_ACTION AN-6-ACP_CHANNEL_TO_NBR_REMOVED 6-Information Removed ACP [chars] from Device Addr [chars] to Autonomic Network Control Plane Channel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_CHANNEL_TO_NBR_REMOVED 6-Information Removed ACP [chars] from Device Addr [chars] to Autonomic Network Control Plane Channel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_DIKE_TO_NBR_CREATED 6-Information Established DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - DIKE tunnel established to neighbor AN LOG_STD_NO_ACTION AN-6-ACP_DIKE_TO_NBR_CREATED 6-Information Established DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - DIKE tunnel established to neighbor AN LOG_STD_NO_ACTION AN-6-ACP_DIKE_TO_NBR_REMOVED 6-Information Removed DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - DIKE tunnel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_DIKE_TO_NBR_REMOVED 6-Information Removed DIKE on ACP [chars] from Device Addr [chars] Autonomic Network Control plane - DIKE tunnel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_IPSEC_TO_NBR_CREATED 6-Information Established IPSEC on ACP from Device Addr [chars] Autonomic Network Control plane - IPSEC tunnel established to neighbor AN LOG_STD_NO_ACTION AN-6-ACP_IPSEC_TO_NBR_CREATED 6-Information Established IPSEC on ACP from Device Addr [chars] Autonomic Network Control plane - IPSEC tunnel established to neighbor AN LOG_STD_NO_ACTION AN-6-ACP_IPSEC_TO_NBR_REMOVED 6-Information Removed IPSEC on ACP from Device Addr [chars] to Autonomic Network Control plane - IPSEC tunnel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_IPSEC_TO_NBR_REMOVED 6-Information Removed IPSEC on ACP from Device Addr [chars] to Autonomic Network Control plane - IPSEC tunnel to neighbor is removed AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_GLOBAL_DISABLE 6-Information Removed OSPFv3 routing globally pid [dec] OSPF routing has been disabled globally AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_GLOBAL_DISABLE 6-Information Removed OSPFv3 routing globally pid [dec] OSPF routing has been disabled globally AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_GLOBAL_ENABLED 6-Information Enabled global OSPFv3 pid [dec]rid [inet]area [dec] OSPF routing has been enabled globally AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_GLOBAL_ENABLED 6-Information Enabled global OSPFv3 pid [dec]rid [inet]area [dec] OSPF routing has been enabled globally AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_INTERFACE_ENABLED 6-Information OSPF routing enabled on interface: [chars] pid [dec]rid [inet] area [dec] OSPF routing has been enabled on all physical interface AN LOG_STD_NO_ACTION AN-6-ACP_ROUTING_INTERFACE_ENABLED 6-Information OSPF routing enabled on interface: [chars] pid [dec]rid [inet] area [dec] OSPF routing has been enabled on all physical interface AN LOG_STD_NO_ACTION AN-6-ACP_VRF_GLOBAL_CREATE_SUCCESS 6-Information Device UDI [chars] Autonomic VRF Autonomic network VRF has been created globally AN LOG_STD_NO_ACTION AN-6-ACP_VRF_GLOBAL_CREATE_SUCCESS 6-Information Device UDI [chars] Autonomic VRF Autonomic network VRF has been created globally AN LOG_STD_NO_ACTION AN-6-ACP_VRF_GLOBAL_REMOVE 6-Information Device UDI [chars] Autonomic VRF Autonomic network VRF has been removed globally AN LOG_STD_NO_ACTION AN-6-ACP_VRF_GLOBAL_REMOVE 6-Information Device UDI [chars] Autonomic VRF Autonomic network VRF has been removed globally AN LOG_STD_NO_ACTION AN-6-ACP_VRF_INTERFACE_CREATE_SUCCESS 6-Information Device UDI [chars] Autonomic network VRF has been created on the interface AN LOG_STD_NO_ACTION AN-6-ACP_VRF_INTERFACE_CREATE_SUCCESS 6-Information Device UDI [chars] Autonomic network VRF has been created on the interface AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_CONSOLE_INPUT 6-Information Autonomic disabled due to User intervention on console. configure 'autonomic' to enable it. User entered into configuration mode So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_CONSOLE_INPUT 6-Information Autonomic disabled due to User intervention on console. configure 'autonomic' to enable it. User entered into configuration mode So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_MANUAL_CONFIG_DETECTED 6-Information Autonomic disabled due to detection of new configuration. Some other process configures something. So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_MANUAL_CONFIG_DETECTED 6-Information Autonomic disabled due to detection of new configuration. Some other process configures something. So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_NO_AUTONOMIC 6-Information Autonomic disabled due to 'no autonomic' command. 'No autonomic' command is entered So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-AN_ABORTED_BY_NO_AUTONOMIC 6-Information Autonomic disabled due to 'no autonomic' command. 'No autonomic' command is entered So AN is disabled An process is stopped AN LOG_STD_NO_ACTION AN-6-ANR_WHITELIST_CONFIG 6-Information Autonomic registrar with Addr [chars] Domain id [chars] has whitelist- will allow only these devices in autonomic network The autonomic registeration authority has been configured with white list and will allow only these devices to enter its network AN LOG_STD_NO_ACTION AN-6-ANR_WHITELIST_CONFIG 6-Information Autonomic registrar with Addr [chars] Domain id [chars] has whitelist- will allow only these devices in autonomic network The autonomic registeration authority has been configured with white list and will allow only these devices to enter its network AN LOG_STD_NO_ACTION AN-6-ANR_WHITELIST_NOT_CONFIG 6-Information Autonomic registrar with Addr [chars] has no whitelist- will allow all devices The autonomic registeration authority has not been configured with white list and will allow all devices to enter its network AN LOG_STD_NO_ACTION AN-6-ANR_WHITELIST_NOT_CONFIG 6-Information Autonomic registrar with Addr [chars] has no whitelist- will allow all devices The autonomic registeration authority has not been configured with white list and will allow all devices to enter its network AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_FAILED 6-Information Config download on the Device Addr [chars] has FAILED Failed to download the config file to the Running config AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_FAILED 6-Information Config download on the Device Addr [chars] has FAILED Failed to download the config file to the Running config AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_STARTED 6-Information Config download started on the Device Addr [chars] Config download is triggerred AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_STARTED 6-Information Config download started on the Device Addr [chars] Config download is triggerred AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_SUCCESS 6-Information Config download at the Device Addr [chars] Download of the config file to the Running config is Successful AN LOG_STD_NO_ACTION AN-6-CONFIG_DOWNLOAD_SUCCESS 6-Information Config download at the Device Addr [chars] Download of the config file to the Running config is Successful AN LOG_STD_NO_ACTION AN-6-CONFIG_SAVE 6-Information Issuing 'write memory' to save config Saving configurations to startup-config by AN process AN LOG_STD_NO_ACTION AN-6-CONFIG_SAVE 6-Information Issuing 'write memory' to save config Saving configurations to startup-config by AN process AN LOG_STD_NO_ACTION AN-6-DEVICE_ALLOWED_BY_ANR 6-Information Device with udi [chars] is allowed by autonomic registrar in its Domain ID [chars] with addr [chars] and Device ID [chars] The autonomic network registration authority has authorised this device to enter its network AN LOG_STD_NO_ACTION AN-6-DEVICE_ALLOWED_BY_ANR 6-Information Device with udi [chars] is allowed by autonomic registrar in its Domain ID [chars] with addr [chars] and Device ID [chars] The autonomic network registration authority has authorised this device to enter its network AN LOG_STD_NO_ACTION AN-6-DEVICE_ENROLLED 6-Information Device with UDI [chars] connected to Proxy Addr [chars] on the interface [chars] is allowed by Autonomic registrar Addr [chars] The autonomic network registration authority has enrolled this device AN LOG_STD_NO_ACTION AN-6-DEVICE_ENROLLED 6-Information Device with UDI [chars] connected to Proxy Addr [chars] on the interface [chars] is allowed by Autonomic registrar Addr [chars] The autonomic network registration authority has enrolled this device AN LOG_STD_NO_ACTION AN-6-MASA_NOT_CONFIG 6-Information Autonomic registrar with udi [chars] has no reachability to MASA -not configured Cant verify device udi [chars] The manufacturer authorised signing authority has not been configured cannot do the verification of device AN LOG_STD_NO_ACTION AN-6-MASA_NOT_CONFIG 6-Information Autonomic registrar with udi [chars] has no reachability to MASA -not configured Cant verify device udi [chars] The manufacturer authorised signing authority has not been configured cannot do the verification of device AN LOG_STD_NO_ACTION AN-6-MY_DOMAIN_CERT_EXPIRED 6-Information Domain certificate of this device Addr [chars] has expired The domain certificate of this device has expired AN LOG_STD_NO_ACTION AN-6-MY_DOMAIN_CERT_EXPIRED 6-Information Domain certificate of this device Addr [chars] has expired The domain certificate of this device has expired AN LOG_STD_NO_ACTION AN-6-MY_DOMAIN_CERT_RENEWED 6-Information Domain certificate of device Addr [chars] has been renewed The domain certificate of this device is renewed AN LOG_STD_NO_ACTION AN-6-MY_DOMAIN_CERT_RENEWED 6-Information Domain certificate of device Addr [chars] has been renewed The domain certificate of this device is renewed AN LOG_STD_NO_ACTION AN-6-NBR_DOMAIN_CERT_VALID 6-Information Domain certificate of Neighbor with Addr [chars] The domain certificate of the neighbor device is validated successfully AN LOG_STD_NO_ACTION AN-6-NBR_DOMAIN_CERT_VALID 6-Information Domain certificate of Neighbor with Addr [chars] The domain certificate of the neighbor device is validated successfully AN LOG_STD_NO_ACTION AN-6-SUDI_AVAILABLE 6-Information secure UDI - [chars] Secure unique device identification number is available on the device AN LOG_STD_NO_ACTION AN-6-SUDI_AVAILABLE 6-Information secure UDI - [chars] Secure unique device identification number is available on the device AN LOG_STD_NO_ACTION AN-6-UDI_AVAILABLE 6-Information UDI - [chars] Unique device identification number is available on the device AN LOG_STD_NO_ACTION AN-6-UDI_AVAILABLE 6-Information UDI - [chars] Unique device identification number is available on the device AN LOG_STD_NO_ACTION API_BAD_ARGUMENTS-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_BAD_ARGUMENTS-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_BAD_RESPONSE-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_BAD_RESPONSE-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_FAILED-3-L2VPN 3-Error ERRMSG_NOFLAGS - - - API_FAILED-3-L2VPN 3-Error ERRMSG_NOFLAGS - - - API_FAILED-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_FAILED-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_MSG-3-LDP 3-Error ERRMSG_NOFLAGS - - - API_MSG-3-LDP 3-Error ERRMSG_NOFLAGS - - - APM-3-CACHE_SIZE 3-Error Configured cache size is too large. Value has been limited to [dec]100 x platform default. configured cache size is too big media-mon LOG_STD_ACTION APM-3-CACHE_SIZE 3-Error Configured cache size is too large. Value has been limited to [dec]100 x platform default. configured cache size is too big media-mon LOG_STD_ACTION APM-3-INIT 3-Error [chars] Easy Perf Mon Initialization failed media-mon LOG_STD_ACTION APM-3-INIT 3-Error [chars] Easy Perf Mon Initialization failed media-mon LOG_STD_ACTION APM-3-LIST 3-Error [chars] [chars] List operation error occurred. media-mon LOG_STD_ACTION APM-3-LIST 3-Error [chars] [chars] List operation error occurred. media-mon LOG_STD_ACTION APM-3-MEM 3-Error Memory [chars] failed - [chars] Memory operation failed media-mon LOG_STD_ACTION APM-3-MEM 3-Error Memory [chars] failed - [chars] Memory operation failed media-mon LOG_STD_ACTION APPFW-3-HTTP_APPFW_CONF_ERROR 3-Error Application Firewall configuration error -- [chars] An error has occurred during Application Firewall configuration. appfw "This message indicates an error during firewall configuration " "and may be a potential security problem." APPFW-3-HTTP_MAX_REQ_EXCEED 3-Error Maximum of [dec] unanswered HTTP requests exceeded from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_CONT_LENGTH 4-Warning content-length The HTTP message has been detected to violate the content-length \n\ application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_CONT_TYPE_MATCH 4-Warning Sig:[dec] Content type not found - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_CONT_TYPE_SIZE 4-Warning Sig:[dec] Content size %lu out of range - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_CONT_TYPE_VERIFY 4-Warning Sig:[dec] Content type does not match the specified type - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_DEOBFUSCATE 4-Warning Sig:[dec] Deobfuscation signature detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ deobfuscate application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_MATCH_REQ_RESP 4-Warning Sig:[dec] Content type: [chars] does not match the Accept-Type from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ content-type-verification application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_MAX_HDR_LEN 4-Warning Sig:[dec] HTTP Header length exceeded. Received %lu byte of header - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ max-hdr-len application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_MAX_URI_LEN 4-Warning Sig:[dec] HTTP URI length exceeded. Received %lu byte of URL - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ max-uri-len application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_PORT_MISUSE_IM 4-Warning Sig:[dec] HTTP Instant Messenger detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_PORT_MISUSE_P2P 4-Warning Sig:[dec] HTTP Peer-to-Peer detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_PORT_MISUSE_TUNNEL 4-Warning Sig:[dec] HTTP Tunnel detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ port misuse application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_REQ_METHOD_EXT 4-Warning Sig:[dec] HTTP Extension method illegal - [chars] '[chars]' from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ request-method application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_REQ_METHOD_RFC 4-Warning Sig:[dec] HTTP RFC method illegal - [chars] '[chars]' from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ request-method application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_STRICT_PROTOCOL 4-Warning Sig:[dec] HTTP protocol violation detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the strict-http \n\ application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-4-HTTP_TRANSFER_ENCODE 4-Warning Sig:[dec] HTTP Transfer encoding violation detected - [chars] [chars] from [inet]:[dec] to [inet]:[dec] The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-6-HTTP_SESSION_AUDIT_TRAIL 6-Information HTTP session initiator [inet]:[dec] sends [dec] bytes - responder [inet]:[dec] sends [dec] bytes The HTTP message has been detected to violate the \n\ transfer encoding application firewall inspection rule. appfw "This message is for informational purposed only but may indicate \n\ a security problem." APPFW-6-IM_AOL_CLIENT_VERSION 6-Information im-aol [inet]:[dec] attempting to establish connection with aol server [inet]:[dec] using an unsupported version of the client The AOL client version is not supported appfw "This message is for informational purposed only." APPFW-6-IM_AOL_SESSION 6-Information im-aol [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec] The AIM well known service message has been detected. appfw "This message is for informational purposed only." APPFW-6-IM_MSN_CLIENT_VERSION 6-Information im-msn [inet]:[dec] attempting to establish connection with msn server [inet]:[dec] using an unsupported version of the client The MSN client version is not supported appfw "This message is for informational purposed only." APPFW-6-IM_MSN_SESSION 6-Information im-msn [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec] The MSNMSGR well known service message has been detected. appfw "This message is for informational purposed only." APPFW-6-IM_YAHOO_CLIENT_VERSION 6-Information im-yahoo [inet]:[dec] attempting to establish connection with yahoo server [inet]:[dec] using an unsupported version of the client The YAHOO client version is not supported appfw "This message is for informational purposed only." APPFW-6-IM_YAHOO_P2P_CHAT 6-Information im-yahoo text-chat service session: [inet]:[dec] establishing a direct chat with [dec].[dec].[dec].[dec] A specific service yyyy has been detected to establish\n\ a direct connection with another peer in a Yahoo! Instant Messenger \n\ application and the application firewall inspection policy has been\n\ configured to send an alarm for this event. Typical services are ñ \n\ text-chat voice-chat file-transfer etc. appfw "This message is for informational purposed only." APPFW-6-IM_YAHOO_SESSION 6-Information im-yahoo [chars] service session initiator [inet]:[dec] [chars] [dec] bytes [chars] responder [inet]:[dec] The YMSGR well known service message has been detected. appfw "This message is for informational purposed only." APPNAV_CLIENT-3-CFT_INIT_FAILED 3-Error AppNav failed initialize flow table - [dec]. Flow table is a critical component of AppNav. The failure is likely due to lack of memory DRAM on the ESP. The service-controller LOG_STD_REDUCE_ACTION APPNAV_CONTROLLER-2-ACG_IP_CHANGED 2-Critical APPNAV-CONTROLLER: Alarm #10000 Severity: Major \nAppnav controller group IP address changed! All relevant service contexts will be disabled Appnav controller group IP address changed! All relevant service contexts will be disabled service-controller "Change AppNav Controller's IP " APPNAV_CONTROLLER-2-ACG_IP_CHANGED 2-Critical APPNAV-CONTROLLER: Alarm #10000 Severity: Major \nAppnav controller group IP address changed! All relevant service contexts will be disabled Appnav controller group IP address changed! All relevant service contexts will be disabled service-controller "Change AppNav Controller's IP " APPNAV_CONTROLLER-2-SC_CONVERGENCE_FAILED 2-Critical APPNAV-CONTROLLER: Alarm #29001 Severity: Major CMM is not coming out of convergence state service-controller "Check connectivity between SN's and AC's" APPNAV_CONTROLLER-2-SC_CONVERGENCE_FAILED 2-Critical APPNAV-CONTROLLER: Alarm #29001 Severity: Major CMM is not coming out of convergence state service-controller "Check connectivity between SN's and AC's" APPNAV_CONTROLLER-2-SC_DEGRADED_CLUSTER 2-Critical APPNAV-CONTROLLER: Alarm #29002 Severity: Critical. AC: [chars] is Degraded Mismatch of stable AC views between AC's service-controller "Check connectivity between AC's" APPNAV_CONTROLLER-2-SC_DEGRADED_CLUSTER 2-Critical APPNAV-CONTROLLER: Alarm #29002 Severity: Critical. AC: [chars] is Degraded Mismatch of stable AC views between AC's service-controller "Check connectivity between AC's" APPNAV_CONTROLLER-2-SC_SC_UNREACHABLE 2-Critical APPNAV-CONTROLLER: Alarm #29006 Severity: Major. AC: [chars] unreachable Connectivity with AC's under ACG is lost service-controller "Make sure AC's configured under ACG are up" " and reachable" APPNAV_CONTROLLER-2-SC_SC_UNREACHABLE 2-Critical APPNAV-CONTROLLER: Alarm #29006 Severity: Major. AC: [chars] unreachable Connectivity with AC's under ACG is lost service-controller "Make sure AC's configured under ACG are up" " and reachable" APPNAV_CONTROLLER-2-SC_SN_EXCLUDED 2-Critical APPNAV-CONTROLLER: Alarm #29008 Severity: Major. SN: [chars] excluded Stable SN views across AC's are different. Those SN's that are not reachable by other AC's are exlcuded service-controller "Make sure excluded SN's are reachable from " "all AC's" APPNAV_CONTROLLER-2-SC_SN_EXCLUDED 2-Critical APPNAV-CONTROLLER: Alarm #29008 Severity: Major. SN: [chars] excluded Stable SN views across AC's are different. Those SN's that are not reachable by other AC's are exlcuded service-controller "Make sure excluded SN's are reachable from " "all AC's" APPNAV_CONTROLLER-2-SC_SN_UNREACHABLE 2-Critical APPNAV-CONTROLLER: Alarm #29007 Severity: Major. SN: [chars] is unreachable Service context has entered Operational state and there is at least one configured node that is not part of the SN view. service-controller "Check status of configured SNs." APPNAV_CONTROLLER-2-SC_SN_UNREACHABLE 2-Critical APPNAV-CONTROLLER: Alarm #29007 Severity: Major. SN: [chars] is unreachable Service context has entered Operational state and there is at least one configured node that is not part of the SN view. service-controller "Check status of configured SNs." APPNAV_CONTROLLER-2-SNG_AO_UNAVAILABLE 2-Critical APPNAV-CONTROLLER: Alarm #30000Severity: Major. In SNG: [chars] AO: [dec] is unavailable No node in service node group is available for optimization and traffic is getting optimized by a secondary SNG. service-controller "Check status of configured SNs." APPNAV_CONTROLLER-2-SNG_AO_UNAVAILABLE 2-Critical APPNAV-CONTROLLER: Alarm #30000Severity: Major. In SNG: [chars] AO: [dec] is unavailable No node in service node group is available for optimization and traffic is getting optimized by a secondary SNG. service-controller "Check status of configured SNs." APPNAV_CONTROLLER-2-SNG_UNAVAILABLE 2-Critical APPNAV-CONTROLLER: Alarm #30001 Severity: Major. SNG: [chars] unavailable No SN in appnav node group is available for optimization. service-controller "Check status of configured nodes." APPNAV_CONTROLLER-2-SNG_UNAVAILABLE 2-Critical APPNAV-CONTROLLER: Alarm #30001 Severity: Major. SNG: [chars] unavailable No SN in appnav node group is available for optimization. service-controller "Check status of configured nodes." APPNAV_CONTROLLER-3-CM_REGISTER_FAILED 3-Error AppNav registration with Central Manager failed for the following reason: [chars] Received a registration failure message from the AppNav Central Manager. AppNav has not registered with the Central Manager service-controller "Issue the " "debug waas management errors " "command and the " "debug waas management events " "Contact your Cisco technical support representative" " and provide the representative with the gathered information." APPNAV_CONTROLLER-3-CM_REGISTER_FAILED 3-Error AppNav registration with Central Manager failed for the following reason: [chars] Received a registration failure message from the AppNav Central Manager. AppNav has not registered with the Central Manager service-controller "Issue the " "debug waas management errors " "command and the " "debug waas management events " "Contact your Cisco technical support representative" " and provide the representative with the gathered information." APPNAV_CONTROLLER-4-SC_CLUSTER_STABLE 4-Warning APPNAV-CONTROLLER: Alarm #29002 cleared. AC: [chars] is Stable Mismatch of stable AC views between AC's service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_CLUSTER_STABLE 4-Warning APPNAV-CONTROLLER: Alarm #29002 cleared. AC: [chars] is Stable Mismatch of stable AC views between AC's service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_CONVERGENCE_SUCCESS 4-Warning APPNAV-CONTROLLER: Alarm #29001 cleared CMM convergence completed service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_CONVERGENCE_SUCCESS 4-Warning APPNAV-CONTROLLER: Alarm #29001 cleared CMM convergence completed service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SC_REACHABLE 4-Warning APPNAV-CONTROLLER: Alarm #29006 cleared. AC: [chars] reachable Connectivity with AC's under ACG is regained service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SC_REACHABLE 4-Warning APPNAV-CONTROLLER: Alarm #29006 cleared. AC: [chars] reachable Connectivity with AC's under ACG is regained service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SN_INCLUDED 4-Warning APPNAV-CONTROLLER: Alarm #29008 cleared. SN: [chars] included SN is reachable again service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SN_INCLUDED 4-Warning APPNAV-CONTROLLER: Alarm #29008 cleared. SN: [chars] included SN is reachable again service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SN_REACHABLE 4-Warning APPNAV-CONTROLLER: Alarm #29007 cleared. SN: [chars] is reachable Service Node is available service-controller "None. All is well" APPNAV_CONTROLLER-4-SC_SN_REACHABLE 4-Warning APPNAV-CONTROLLER: Alarm #29007 cleared. SN: [chars] is reachable Service Node is available service-controller "None. All is well" APPNAV_CONTROLLER-4-SERVICE_CTX_DISABLE 4-Warning SERVICE-CONTROLLER: Alarm 10001 Severity: Major \n Disabling service context [chars] Disabling service context - - APPNAV_CONTROLLER-4-SERVICE_CTX_DISABLE 4-Warning SERVICE-CONTROLLER: Alarm 10001 Severity: Major \n Disabling service context [chars] Disabling service context - - APPNAV_CONTROLLER-4-SNG_AO_AVAILABLE 4-Warning APPNAV-CONTROLLER: Alarm #30000 cleared. In SNG: [chars] AO: [dec] is available Service node group is available for optimization service-controller "None. All is well" APPNAV_CONTROLLER-4-SNG_AO_AVAILABLE 4-Warning APPNAV-CONTROLLER: Alarm #30000 cleared. In SNG: [chars] AO: [dec] is available Service node group is available for optimization service-controller "None. All is well" APPNAV_CONTROLLER-4-SNG_AVAILABLE 4-Warning APPNAV-CONTROLLER: Alarm #30001 Cleared SNG: [chars] available SN's in appnav node group is available for optimization. service-controller "None. All is well" APPNAV_CONTROLLER-4-SNG_AVAILABLE 4-Warning APPNAV-CONTROLLER: Alarm #30001 Cleared SNG: [chars] available SN's in appnav node group is available for optimization. service-controller "None. All is well" APPNAV_CONTROLLER-5-SC_MIXED_FARM 5-Notice APPNAV-CONTROLLER: Alarm #29003 Severity: Minor When an appnav controller detects upon that there are other appnav-controllers/SNs in the cluster with different ICIMP/DMP minor version number. service-controller "Check versions of SNs in network." APPNAV_CONTROLLER-5-SC_MIXED_FARM 5-Notice APPNAV-CONTROLLER: Alarm #29003 Severity: Minor When an appnav controller detects upon that there are other appnav-controllers/SNs in the cluster with different ICIMP/DMP minor version number. service-controller "Check versions of SNs in network." APPNAV_CONTROLLER-5-SC_MIXED_FARM_CLEAR 5-Notice APPNAV-CONTROLLER: Alarm #29003 cleared There are no appnav-controllers/SNs with different ICIMP/DMP minor version number service-controller "None. All is well" APPNAV_CONTROLLER-5-SC_MIXED_FARM_CLEAR 5-Notice APPNAV-CONTROLLER: Alarm #29003 cleared There are no appnav-controllers/SNs with different ICIMP/DMP minor version number service-controller "None. All is well" APPNAV_CONTROLLER-6-CM_REGISTER_SUCCESS 6-Information AppNav registered with Central Manager successfully Received a registration success message from the Central Manager service-controller "None. All is well" APPNAV_CONTROLLER-6-CM_REGISTER_SUCCESS 6-Information AppNav registered with Central Manager successfully Received a registration success message from the Central Manager service-controller "None. All is well" APS-1-NO_ACTIVE 1-Alert No Active Port In Group [chars] After an active interface failure the system\n\ switches over to the standby interface if APS has\n\ been enabled. This message is posted if after a\n\ switchover the system finds no active interface\n\ i.e. both working and protection interfaces are\n\ found to be nonoperational. - "Isolate the cause of failure on both working\n\ and protection interfaces." APS-2-CHNLCFGMM 2-Critical Group [chars]: Channel Config Mismatch Working and Protection interfaces do not point to the\n\ same path on local and remote network elements - "Configure working and protection interfaces\n\ to point to the same path on local and remote\n\ network elements" APS-2-CHNLMISMATCH 2-Critical Group [chars]: Channel Mismatch - [chars] - - "Check for any failures on the APS commnication\n\ channel. If APS communication channel is\n\ operational contact Cisco TAC." APS-2-FEPF 2-Critical Group [chars]: Far End Prot Failure - [chars] - - "Isolate the cause of failure on the protection\n\ channel on the remote network element." APS -2-INITSYS 2-Critical [chars] A software error occurred during initialization of\n\ the APS subsystem - "Check for sufficient processor memory." LOG_STD_ACTION APS-2-INTRNLERR 2-Critical [chars] [dec] APS software detected an internal error - LOG_STD_ACTION APS-2-MODEMISMATCH 2-Critical Group [chars]: Mode Mismatch - [chars] - - "Configure the remote APS group for\n\ bidirectional operation." APS-2-NOSOCKET 2-Critical Failed To Open Socket This message is posted when the APS subsystem fails\n\ to create a UDP socket for exchanging APS channel\n\ protocol messages over APS message channel configured\n\ for IP. This usually is due to a low memory condition\n\ in the system - LOG_STD_REDUCE_ACTION APS-2-PSBF 2-Critical Group [chars]: Prot Switch Byte Failure - [chars] - - "Check for failures on the APS communication\n\ channel. Isolate the cause for such failures\n\ and restore the communication channel to\n\ working condition" APS-3-PORT_FAIL 3-Error [chars] Port Fail On [chars] This message is posted when APS subsystem receives\n\ a port fail indication from the driver subsystem.\n\ This message indicates that the specified interface\n\ has detected a failure condition\n\ e.g. Loss Of Light. - "Isolate the cause of the failure and restore\n\ the interface to normal operational\n\ condition." APS-6-ADJUSTMODE 6-Information Group [chars]: Mode Mismatch - [chars] This message is posted by the local network element\n\ if the local APS group has been configured for\n\ bidirectional operation but the associated remote\n\ APS group has been configured for unidirectional\n\ operation. This message is posted after the local\n\ network element detects the mismatch and changes\n\ the operation to unidirectional. - "Configure the remote APS group for\n\ bidirectional operation." APS-6-AUTOFOVER 6-Information Auto-Failover - Group [chars] This message is posted if APS hardware\n\ successfully switched over to the standby interface\n\ after the failure of the active interface. This is\n\ informational only. - "Isolate the cause of failure of the previous\n\ active interface and restore it to a working\n\ condition." APS-6-BIDIRSWCH 6-Information Group [chars]: Remote Request - [chars] This message is posted by the local network element\n\ after an APS switchover that is triggered by an APS\n\ request from the remote network element. This is\n\ informational only. - LOG_STD_NO_ACTION APS-6-CHNLACTIVE 6-Information Group [chars] - [chars] channel is now ACTIVE This message is posted when a previously standby\n\ channel becomes the active channel. This is\n\ informational only. - LOG_STD_NO_ACTION APS-6-DISAUTFOV 6-Information Disable Auto-Failover On [chars] APS has disabled auto-failover for the indicated\n\ group - show aps group APS-6-ENAUTFOVR 6-Information Enable Auto-Failover On [chars] This message is posted when APS software enables\n\ hardware to perform APS actions for failures\n\ detected by the hardware. This is informational\n\ only. - LOG_STD_NO_ACTION ARAP-0-DEFAULT 0-Emergency TTY [dec] An internal software error occured. - LOG_STD_SH_TECH_ACTION ARAP-0-NOTNULLRESEND 0-Emergency TTY [dec] An internal software error occured. - LOG_STD_SH_TECH_ACTION ARAP-0-NULLRESEND 0-Emergency TTY [dec] An internal software error occured. - "Report this error to you technical support representative." ARAP-0-VSERROR 0-Emergency TTY [dec]: VS queued error An internal software error occured. - LOG_STD_SH_TECH_ACTION ARAP-0-WAITBADMSG 0-Emergency TTY [dec]: arg msg bad [hec] The router received an invalid packet during ARAP MNP4 connection\ setup phase. - "Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems." ARAP-2-NOLOG 2-Critical TTY [dec]: Could not malloc log Memory not available for internal MNP4 logging. - LOG_STD_SH_TECH_ACTION ARAP-3-ABORTED 3-Error TTY [dec]: arap callback aborted An unexpected message was received during the Microcom Networking\n\ Protocol version 4 MNP4 link setup. - LOG_STD_ACTION ARAP-3-BADCONFIG 3-Error TTY [dec]: unhandled configuration command A configuration command was not recognized. - "Check the configuration file on the server for any invalid\n\ configuration commands." ARAP-3-BADPAK 3-Error TTY [dec]: Bad packet type in arap_send_msg Internal data structures are corrupted. - "Check for abnormally high CPU usage." ARAP-3-REMOTEERROR 3-Error TTY [dec]: arap input error ARAP connection was terminated without a known cause. - LOG_STD_ACTION ARAP-3-TIMEOUT 3-Error TTY [dec]: arap expected message timeout The SCP process has been terminated. - "If this message recurs copy the error message exactly as it appears\n\ and report it to your technical support representative." ARAP-4-CONFAILED 4-Warning TTY [dec]: ARAP connection failed: [chars] The ARA protocol client was denied access probably due to a\n\ configuration problem on the server. The error message should indicate\n\ the problem. This message does not indicate access denials due to bad\n\ passwords. - "Investigate the problem reported in the error message." ARAP-4-NOEXTTACACS 4-Warning TTY [dec]: arap TACACS is configured but extended TACACS is not. - - "Configure extended TACACS." ARAP-5-INITCONFUSED 5-Notice TTY [dec]: ARAP unexpected initialization packet [chars] The startup negotiation between a client and the ARA protocol server\n\ fell out of order. If this message is received sporadically it\n\ indicates line noise. - "If this message recurs reinstall the ARA client software." ARAP-5-PAKINVALID 5-Notice TTY [dec]: ARAP invalid packet received This message appears only when ARA protocol logging is configured. The\n\ message notes that an ARA protocol user has logged out. - LOG_STD_NO_ACTION ARAP-6-BADEXIT 6-Information TTY [dec]: exited user [chars]: [chars] A user was disconnected from ARA protocol at an unexpected time. The\n\ disconnection may be due to modems dropping server error client\n\ problems or any number of other difficulties. - "To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports." ARAP-6-LRPHASERROR 6-Information TTY [dec]: Received LT in CONNECTION PHASE The router received an invalid packet during ARA connection setup\ phase. - "Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems." ARAP-6-MAXRESENDS 6-Information TTY [dec] The router resent MNP4 packets maximum number of times without\ receiving an acknowledgement. - "To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports." ARAP-6-MNP4RCVDISC 6-Information TTY [dec]: MNP4 input disconnect This indicates that the router received disconnect request\ from the remote Macintosh client. - LOG_STD_NO_ACTION ARAP-6-MNP4T401 6-Information TTY [dec]: T401 [dec] baud rate [dec] This message indicates that the router received MNP4 connection\ request. MNP4 acknowledgement timer value is also indicated. - LOG_STD_NO_ACTION ARAP-6-RCVGIANT 6-Information TTY [dec]: Rcv giant. dropping frame The router received an oversized MNP4 frame. - "Check for excessive line noise.\ Check the ARAP client software configuration for\ possible problems." ARAP-6-RCVNOPAK 6-Information TTY [dec]: Receive getbuffer failure. dropping frame No buffer exists for an incoming packet. - "Examine buffer usage statistics. Possibly more memory is\ required." ARAP-6-RESENDSLOW 6-Information TTY [dec] The router repeated resending of MNP4 packets as the\ Macintosh client failed to acknowledge previously resent packets. - "If this error message persists for several ARAP connections\ report it to your technical support representative." ARAP-6-TIMERERROR 6-Information TTY [dec]: MNP4 timeout error The router is dropping the connection after doing maximum resends. - "To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports." ARAP-6-XTICKLE 6-Information TTY [dec]: exited user [chars]: Other side stopped answering ARAP tickles\ mnp4 pak resent [dec] mnp4 pak sent [dec] last [dec] now [dec] The router disconnected as the remote Macintosh client stopped\ sending ARAP tickle or data packets. - "To determine the cause of the disconnection correlate the receipt of\n\ this message with the user problem reports." ARCHIVE_CONFIG-4-ARCHIVE_DELETE_FAILED 4-Warning Delete of a previously saved archive of the router configuration could not be completed. The router could not delete a file that was previously written. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted. - "None" ARCHIVE_CONFIG-4-ARCHIVE_DELETE_FAILED 4-Warning Delete of a previously saved archive of the router configuration could not be completed. The router could not delete a file that was previously written. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted. - "None" ARCHIVE_CONFIG-4-ARCHIVE_SKIPPED 4-Warning Archive of router configuration was skipped due to a previous initiation. Only one archive can be created at a time. Two or more simultaneous archives in progress is not allowed. This could occur for example if two users attempt to create an archive simultaneouly. - "Retry the archive creation later when the previous archive has finished being written." ARCHIVE_CONFIG-4-ARCHIVE_SKIPPED 4-Warning Archive of router configuration was skipped due to a previous initiation. Only one archive can be created at a time. Two or more simultaneous archives in progress is not allowed. This could occur for example if two users attempt to create an archive simultaneouly. - "Retry the archive creation later when the previous archive has finished being written." ARCHIVE_CONFIG-6-ARCHIVE_CREATE_FAILED_STANDBY 6-Information Could not create an archive of the router configuration on the standby RP. The router could not create an archive file on the standby RP. The file that was being created contains an archive of the router configuration. This could occur for example if the active RP cannot communicate with the standby RP. - "None" ARCHIVE_CONFIG-6-ARCHIVE_CREATE_FAILED_STANDBY 6-Information Could not create an archive of the router configuration on the standby RP. The router could not create an archive file on the standby RP. The file that was being created contains an archive of the router configuration. This could occur for example if the active RP cannot communicate with the standby RP. - "None" ARCHIVE_CONFIG-6-ARCHIVE_DELETE_FAILED_STANDBY 6-Information Delete of a previously saved archive of the router configuration could not be completed on the standby RP. The router could not delete a file that was previously written on the standby RP. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted. Alternatively the file could not be deleted when the active RP cannot communicate with the standby RP. - "None" ARCHIVE_CONFIG-6-ARCHIVE_DELETE_FAILED_STANDBY 6-Information Delete of a previously saved archive of the router configuration could not be completed on the standby RP. The router could not delete a file that was previously written on the standby RP. The file that was being deleted file contains an archive of the router configuration. This could occur for example if the file was manually deleted. Alternatively the file could not be deleted when the active RP cannot communicate with the standby RP. - "None" ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED 3-Error Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error. An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED 3-Error Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error. An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED 3-Error Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error. An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_CMD_INIT_FAILED 3-Error Failed to register the special case [chars] command:\[chars]\ during initialization. Config Diff and Rollback cannot be used as a result of this error. An internal software error occurred during initialization - Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_INIT_FAILED 3-Error Could not initialize the Config Diff and Rollback subsystem An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_INIT_FAILED 3-Error Could not initialize the Config Diff and Rollback subsystem An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_INIT_FAILED 3-Error Could not initialize the Config Diff and Rollback subsystem An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-3-DIFF_INIT_FAILED 3-Error Could not initialize the Config Diff and Rollback subsystem An internal software error occurred during initialization. Config Diff and Rollback cannot be used as a result of this error. - "Copy the error message exactly as it appears. Copy down the system's " "configuration along with any other relevant information. Contact your " "technical support representative for assistance." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP 5-Notice Backing up current running config to [chars] The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP 5-Notice Backing up current running config to [chars] The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP 5-Notice Backing up current running config to [chars] The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_BACKUP 5-Notice Backing up current running config to [chars] The current running config is saved so that when the timer expires if no confirmation has been received from user to confirm what they've configured the system will rollback to the saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL 5-Notice User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated. - "Remove the error condition and try again later." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL 5-Notice User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated. - "Remove the error condition and try again later." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL 5-Notice User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated. - "Remove the error condition and try again later." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CANCEL 5-Notice User: [chars]Priv: [dec] View: [dec]: Rollback Confirmed Change is cancelled due to [chars] failure Rollback Confirmed Change is normally configured along with other configuration operations such as \config term\ or \config replace\. If those operation failed Rollback Confirmed Change should not be activated. - "Remove the error condition and try again later." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM 5-Notice User: [chars]: Confirm the configuration change The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM 5-Notice User: [chars]: Confirm the configuration change The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM 5-Notice User: [chars]: Confirm the configuration change The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_CONFIRM 5-Notice User: [chars]: Confirm the configuration change The configuration change is confirmed. The timer for rolling to the previously saved config is cancelled - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER 5-Notice User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute Reset Rollback Confirmed Change timerabsolute to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER 5-Notice User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute Reset Rollback Confirmed Change timerabsolute to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER 5-Notice User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute Reset Rollback Confirmed Change timerabsolute to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_ABSTIMER 5-Notice User: [chars]: Reset Rollback Confirmed Change timerabsolute to %lu minute Reset Rollback Confirmed Change timerabsolute to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER 5-Notice User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute Reset Rollback Confirmed Change timeridle to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER 5-Notice User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute Reset Rollback Confirmed Change timeridle to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER 5-Notice User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute Reset Rollback Confirmed Change timeridle to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_RESET_IDLETIMER 5-Notice User: [chars] Reset Rollback Confirmed Change timeridle to %lu minute Reset Rollback Confirmed Change timeridle to a new value - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW 5-Notice User: [chars]: Rollback immediately. Rollback immediately and cancel the timer - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW 5-Notice User: [chars]: Rollback immediately. Rollback immediately and cancel the timer - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW 5-Notice User: [chars]: Rollback immediately. Rollback immediately and cancel the timer - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_REVERTNOW 5-Notice User: [chars]: Rollback immediately. Rollback immediately and cancel the timer - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY 5-Notice Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY 5-Notice Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY 5-Notice Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_RETRY 5-Notice Failed to acquire configuration lock. Rollback did not start. Schedule to retry in 5 minutes Failed to acquire configuration lock. Rollback did not start. In this case retry will be scheduled. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START 5-Notice Start rolling to: [chars] The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START 5-Notice Start rolling to: [chars] The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START 5-Notice Start rolling to: [chars] The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_ROLLBACK_START 5-Notice Start rolling to: [chars] The timer for Rollback Confirmed Change has expired. System will rollback to the previously saved config. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_ABSTIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] in %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_START_IDLETIMER 5-Notice User: [chars]Priv: [dec] View: [dec]: Scheduled to rollback to config [chars] if session has been idle for %lu minutes The system will wait for the user to confirm that they wish to keep what they've configured until the timer expires. If the confirmation is not received in time the router will rollback. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER 5-Notice System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER 5-Notice System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER 5-Notice System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_ABSTIMER 5-Notice System will rollback to config [chars] in one minute. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER 5-Notice User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER 5-Notice User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER 5-Notice User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_DIFF-5-ROLLBK_CNFMD_CHG_WARNING_IDLETIMER 5-Notice User [chars] on tty [dec] has been idle for %lu minutes. System will rollback to config [chars] in oneminute if it continues to be idle. Enter \configure confirm\ if you wish to keep what you've configured Rollback will start in one minute. User could enter \configure confirm\ if they wish to keep what they've configured. - "This message DOES NOT denote any error condition. It is a part of the " "normal operation of the rollback confirmed change." ARCHIVE_ISSU-2-GET_BUFFER 2-Critical Archive ISSU client failed to get buffer for message. Error: [dec] [chars] The Archive ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. parser "show logging and show checkpoint client" ARCHIVE_ISSU-2-GET_BUFFER 2-Critical Archive ISSU client failed to get buffer for message. Error: [dec] [chars] The Archive ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. parser "show logging and show checkpoint client" ARCHIVE_ISSU-2-INIT 2-Critical Archive ISSU client initialization failed to [chars]. Error: [dec] [chars] The Archive ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. parser LOG_STD_ACTION ARCHIVE_ISSU-2-INIT 2-Critical Archive ISSU client initialization failed to [chars]. Error: [dec] [chars] The Archive ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. parser LOG_STD_ACTION ARCHIVE_ISSU-2-SEND_NEGO_FAILED 2-Critical Archive ISSU client failed to send negotiation message. Error: [dec] [chars] The Archive ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. parser "show logging and show checkpoint client" ARCHIVE_ISSU-2-SEND_NEGO_FAILED 2-Critical Archive ISSU client failed to send negotiation message. Error: [dec] [chars] The Archive ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. parser "show logging and show checkpoint client" ARCHIVE_ISSU-2-SESSION_NEGO_FAIL_START 2-Critical Failed to start Archive ISSU session negotiation. Error: [dec] [chars] The Archive ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly. parser "show issu session " ARCHIVE_ISSU-2-SESSION_NEGO_FAIL_START 2-Critical Failed to start Archive ISSU session negotiation. Error: [dec] [chars] The Archive ISSU client failed to start session negotition. If a problem occurs with the ISSU session start the standby device cannot be brought up properly. parser "show issu session " ARCHIVE_ISSU-2-SESSION_REGISTRY 2-Critical Archive ISSU client failed to register session information. Error: [dec] [chars] The Archive ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. parser "show issu capability entries and " "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-2-SESSION_REGISTRY 2-Critical Archive ISSU client failed to register session information. Error: [dec] [chars] The Archive ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. parser "show issu capability entries and " "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-3-INVALID_SESSION 3-Error Archive ISSU client does not have a valid registered session. The Archive ISSU client does not have a valid registered session. parser "show issu capability entries and " "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-3-INVALID_SESSION 3-Error Archive ISSU client does not have a valid registered session. The Archive ISSU client does not have a valid registered session. parser "show issu capability entries and " "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-3-MSG_NOT_OK 3-Error Archive ISSU client 'Message Type [dec]' is not compatible The Archive ISSU client received an incompatible message from the peer device. The message cannot be processed. parser "show issu message group and " "show issu session and " "show issu negotiated version " ARCHIVE_ISSU-3-MSG_NOT_OK 3-Error Archive ISSU client 'Message Type [dec]' is not compatible The Archive ISSU client received an incompatible message from the peer device. The message cannot be processed. parser "show issu message group and " "show issu session and " "show issu negotiated version " ARCHIVE_ISSU-3-MSG_SIZE 3-Error Archive ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Archive ISSU client failed to calculate the MTU for the specified message. The Archive ISSU client is not able to send the message to the standby device. parser "show issu message group and " "show issu session and " "show issu negotiated version " ARCHIVE_ISSU-3-MSG_SIZE 3-Error Archive ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Archive ISSU client failed to calculate the MTU for the specified message. The Archive ISSU client is not able to send the message to the standby device. parser "show issu message group and " "show issu session and " "show issu negotiated version " ARCHIVE_ISSU-3-SESSION_UNREGISTRY 3-Error Archive ISSU client failed to unregister session information. Error: [dec] [chars] The Archive ISSU client failed to unregister session information. parser "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-3-SESSION_UNREGISTRY 3-Error Archive ISSU client failed to unregister session information. Error: [dec] [chars] The Archive ISSU client failed to unregister session information. parser "show issu session and " "show issu negotiated capability " ARCHIVE_ISSU-3-TRANSFORM_FAIL 3-Error Archive ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Archive ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Archive state between the active device and the standby device is not identical. parser "show issu session and " "show issu negotiated version " ARCHIVE_ISSU-3-TRANSFORM_FAIL 3-Error Archive ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Archive ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Archive state between the active device and the standby device is not identical. parser "show issu session and " "show issu negotiated version " ARP-3-ARPHAMSGFMT 3-Error Malformed ARP HA checkpointing message size = [dec] entry count = [dec]\n - - - ARP-3-ARPINIT 3-Error Internal software error during ARP subsystem initialization\n An internal software error has occurred during ARP subsystem initialization. ip LOG_STD_RECUR_ACTION ARP-3-ARPINT 3-Error ARP table accessed at interrupt level [dec]\n ARP table is accessed at interrupt level which is forbidden. ip LOG_STD_RECUR_ACTION ARP-3-ARPINVALIDEENTRY 3-Error ARP system internal error. Returns NULL arp entry on node %p\n An internal software error has occurred in ARP subsystem an NULL arp entry is got. ip LOG_STD_RECUR_ACTION ARP-3-NULL_IF_INPUT 3-Error ARP packet with NULL if_Input ARP received a packet with NULL input interface ip "If this message recurs call your technical support " "representative for assistance." ARP-3-STCKYARPOVR 3-Error Attempt to overwrite Sticky ARP entry: [inet] hw: [enet] by hw: [enet]\n Multiple stations configured with same IP in Private VLAN. Possible case of IP address stealing. - "Change the IP address of one of the two systems." ARP-3-TABLEERR 3-Error Internal software error during ARP table operation for ARP entry\n An internal software error has occurred during an ARP table operation. ip LOG_STD_RECUR_ACTION ARP-4-ARPADJ 4-Warning Received CEF Adjacency updation request on different interfaces: [inet] on [chars]\n A request to update CEF adjacency came on two different interfaces. ip LOG_STD_RECUR_ACTION ARP-4-ARPLEARNTHRES 4-Warning Learned ARP entries have reached to threshold level %lu This message indicates that the number of dynamically learned ARP entries has reached a preconfigured max. limit in ARP Table. - "First inspect the ARP entries on the interface. If they are " "valid entries either increase the configured max limit or " "reconfigure the network to reduce ARP peers." ARP-4-NULL_SRC_MAC 4-Warning NULL MAC address from [inet] on [chars] Application or peer tried to insert entry with NULL SRC MAC ip "If this message recurs call your technical support " "representative for assistance." ARP-6-ARPLEARNRESUME 6-Information Resuming Learn ARP entries to install in ARP table. This message indicates that the number of dynamically learned ARP entries is in range of permit threshold value.System is allowing new Learned ARP entries to install in ARP table. - LOG_STD_NO_ACTION ASPP-3-NOTTY 3-Error [chars]: Unable to set Rx/Tx tty async service hooks. This message occurs only when ASP is configured. It\n\ indicates the serial interface using ASP is configured\n\ incorrectly or does not support asynchronous mode. - "Verify the correct hardware interface type is being used." ASR1000_PTP-3-FPGA_VER_ERR 3-Error Please consider upgrading the FPGA for PTP to function properly. [chars] 0x[hec] Router is currently running on FPGA version which is lesser than what is required by PTP to work properly asr1000-ptp LOG_STD_ACTION ASR1000_PTP-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message from PTP daemon [chars] - [chars] An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from PTP daemon. asr1000-ptp LOG_STD_ACTION ASR1000_PTP-3-MSGINITFAIL 3-Error Failed to initalize required PTP resource: [chars] During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated. asr1000-ptp LOG_STD_ACTION ASR1000_RP_ATM_SPA-3-ATM_DPIDB_ALLOC_FAIL 3-Error Failed to allocate a data plane identifier for interface [chars] for VCD [dec] The SPA driver is not able to allocate the datapath identifier for the VCD under the interface specified in the message. This indicates a software error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_DPIDB_GET_FAIL 3-Error Failed to get a data plane identifier for interface [chars] for VCD [dec] The SPA driver is not able to obtain the datapath identifier for the VCD under the interface specified in the message. This indicates a software error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_FLOWID_GET_FAIL 3-Error Failed to get a flow control identifier for interface [chars] for index [dec] The SPA driver is not able to obtain the datapath flow control identifier for the data path identifier under the interface specified in the message. This indicates a software error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_FLOWID_OUT_OF_RANGE 3-Error Flow control identifiers for interface [chars] chan lo [hec] chan hi [hec] The flow control identifier received for the interface is out of range. This indicates SPA driver is responding with out of range flow control identifier asr1k-atm LOG_STD_ACTION ASR1000_RP_ATM_SPA-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED 3-Error total active atm vc per ATM SPA reached limitation of [dec] total number of active atm vc per ATM SPA has reached max limit - LOG_STD_ACTION ASR1000_RP_ATM_SPA-3-ATM_SPA_AUTOVC_FAIL 3-Error [chars]: atm autovc discovery configuration failed reason: [chars] A command to configure the atm autovc discovery on an atm interface has failed - LOG_STD_ACTION ASR1000_RP_ATM_SPA-3-ATM_SPA_VC_MAX_LIMIT_REACHED 3-Error total active atm vc reached system limitation of [dec] total number of active atm vc has reached max limit allowed on the system - LOG_STD_ACTION ASR1000_RP_ATM_SPA-3-ATM_TXCHANL_GET_FAIL 3-Error Failed to get a valid tx_chan id for interface [chars] for VCD [dec] The SPA driver is not able to obtain the datapath tx channel identifier for the VCD under the interface specified in the message. This indicates a SPA occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_CFG_SEND_FAIL 3-Error Error in sending message to SPA on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_CON_SET_FAIL 3-Error Failed set ATM con for interface [chars] [dec]/[dec] VCD [dec] Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_CORE_GET_FAIL 3-Error Failed to get a ATM VC core info for interface [chars] VCD [dec] Could not get VC core information when get SPA VCOPEN or VCMODIRY response. This indicates a ATM information error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_DPIDX_GET_FAIL 3-Error Failed to get ATM dpidx for interface [chars] VCD [dec] Could not get VC dpidx information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_EGRESSID_UPDATE_FAIL 3-Error Failed to update ATM egress id for interface [chars] VCD [dec] egress_id [dec] Could not update VC egress id when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_ENCAP_GET_FAIL 3-Error Failed to get ATM encapsulation for interface [chars] [dec]/[dec] VCD [dec] Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_ERROR_ENCAP_TYPE 3-Error Get ATM ERROR encapsulation for interface [chars] [dec]/[dec] VCD [dec] Get a ERROR VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_INGRESS_ID_ALLOC_FAIL 3-Error Failed to allocate VC ingress identifier on interface [chars] for VCD [dec] ebfc_id [dec] when [chars] The ATM SHIM is not able to allocate the ingress identifier for the VCD under the interface specified in the message. This indicates a software error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-ATM_VC_SPA_SETUP_FAIL 3-Error SPA Error response on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] ret_val [dec] The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error. ask1k-atm LOG_STD_NO_ACTION ASR1000_RP_ATM_SPA-3-PROCESS_FAIL 3-Error process creation failed for [chars] The Periodic one second process creation failed. This indicates a software error. asr1k-atm LOG_STD_ACTION ASR1000_RP_ATM_SPA-4-ATM_SPA_VC_ABOVE_WM_WARNING 4-Warning total active atm vc approaching [dec] percent of system limitation of [dec] total number of active atm vc is approaching the high water mark of sysyem limitation - LOG_STD_ACTION ASR1000_RP_ATM_SPA-4-SETUPVC 4-Warning Interface [chars] VC [dec] setup failed reason = [dec] A command to setup a VC has failed on RP. asr1k-spa-atm "The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ASR1000_RP_ATM_SPA-4-TEARDOWNVC 4-Warning Interface [chars] VC [dec] teardown failed vc state = [dec]/[dec] A command to remove a VC config has failed on RP. asr1k-spa-atm "The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ASR1000_RP_ATM_SPA-5-ATM_SPA_VC_BELOW_WM_NOTICE 5-Notice total active atm vc below [dec] percent of system limitation of [dec] total number of active atm vc below the high water mark of sysyem limitation asr1k-atm LOG_STD_ACTION ASR1000_RP_ATM_SPA-5-MPVCVPSETUP 5-Notice Interface [chars] has a VC/VP [dec] configured already VC/VP [dec] cannot The SPA ATM driver supports configuring only one VC/VP under a point to multi point sub-interface. The sub-interface specified in the message already has VP/VC configured. - LOG_STD_NO_ACTION ASR1000_RP_CTE1_SPA-3-CCIPCFAIL 3-Error Communication with the CC has failed for Interface [dec]/[dec] Communication with Card-Carrier down. mcp-io "Either try to configure the Sharded Port Adapter at a later time or " "reload the Card Carrier." ASR1000_RP_CTE1_SPA-3-IPCERR 3-Error Internal IPC error [chars] Internal IPC error. mcp-io "Either try to configure the Sharded Port Adapter at a later time or " "reload the SPA and/or Card Carrier." ASR1000_RP_CTE1_SPA-3-UNSUPERR 3-Error NULL An internal error as resulted from an unsupported or unexpected message. mcp-io "Copy the error message exactly as it appears and report it to your " "technical support representative." ASR1000_RP_POS_SPA-4-ALLOCFAIL 4-Warning Interface [dec]/[dec] allocation failed: [chars] required resources unavailable. mcp-io "Either upgrade system memory or reconfigure memory usage." ASR1000_RP_POS_SPA-4-APSGETFAIL 4-Warning Interface [chars] failed to get aps state from cc asr1k-spa-pos "Copy the error message exactly as it appears on the console\n\ or in the system log. Call your Cisco technical support\n\ representative and provide the representative\n\ with the gathered information." ASR1000_RP_POS_SPA-4-SFSDTHRESHOLDFAIL 4-Warning Interface [chars] failed to update CC about BER_SF_SD thresholds asr1k-spa-pos "Copy the error message exactly as it appears on the console\n\ or in the system log. Call your Cisco technical support\n\ representative and provide the representative\n\ with the gathered information." ASR1000_SIP_CTE1_SPA-3-TDL_ARG_ERR 3-Error Interface [dec]/[dec]/[dec]: Bad parameter in message from RP: [chars] Bad parameter in message from RP. mcp-io "Either try to configure the Sharded Port Adapter at a later time or " "reload the Card Carrier." ASR1000_SIP_CTE1_SPA-3-UNSUPERR 3-Error NULL An internal error as resulted from an unsupported or unexpected message. mcp-io "Copy the error message exactly as it appears and report it to your " "technical support representative." ASR1000_SIP_POS_SPA-3-APS 3-Error APS[dec] [chars] RP deadman timer expired on CC CC is sending LAIS to far end mcp-io "Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information." ASR1000_SIP_POS_SPA-4-ALLOCFAIL 4-Warning SPA resource allocation failed for subslot [dec]/[dec] while [chars] The SPA driver in the subslot specified in the message is\n\ not able to allocate a system resource. The required system resource is\n\ specified in the message. mcp-io "Copy the error message exactly as it appears on the console \n\ or in the system log. Call your Cisco technical support \n\ representative and provide the representative \n\ with the gathered information." ASR1000_SPA_ETHER_DAMSELFLY-3-PLIM_QOS 3-Error Interface [chars] failed to apply PLIM QOS [chars] value = 0x%X Attempt to apply the configured input classification for the specified interface failed asr1k-io-internal "This indicates an internal software failure" ASR1000_SPA_ETHER_DAMSELFLY-3-UNSUPPORTED_XCVR 3-Error Transceiver type [chars] is not allowed on spa [chars] port [dec] This transceiver is not allowed on the SPA asr1k-io-internal "Consult the documentation and ensure supported " "transceivers and plugged into the SPA" ASR1000_SPA_ETHER_LC-3-NP_HW_SW_MISMATCH 3-Error The hardware and software copies of NP client do not match. This indicates reconciliation failure. During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of a register in phy do not match. This indicates an error and the SPA will be reset as normal and impact traffic. asr1k-ether-lc "Open a case with Cisco Technical Assistance Center for further " "assistance" ASR1000_SPA_ETHER_LC-3-PHY_HW_SW_MISMATCH 3-Error The hardware and software copies of a register in the phy for port [dec] do not match. This indicates reconciliation failure. During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of a register in phy do not match. This indicates an error and the SPA will be reset as normal and impact traffic. asr1k-ether-lc "Open a case with Cisco Technical Assistance Center for further " "assistance" ASR1000_SPA_ETHER-3-HSRPDA_TCAM_REGION_FULL 3-Error Failed to add in HSPRDA region for interface [chars] The TCAM HSRPDA table on the SPA is full The specified HSRPDA identifier will not be added to the TCAM table. mcp-io "Try to remove some of the Virtual MAC addresses for the interface by " "command." ASR1000_SPA_ETHER-3-TCAM_QINQ_VLAN_ERROR 3-Error Failed to [chars] VLAN outer [dec] inner [dec]-[dec] to/from interface [chars] status = [dec] The access to update the TCAM VLAN filtering table on the SPA failed. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. mcp-io LOG_STD_ACTION ASR1000_SPA_ETHER-3-TCAM_QINQ_VLAN_TABLE_FULL 3-Error Failed to add VLAN outer [dec] inner [dec]-[dec] to interface [chars] The TCAM VLAN filtering table on the SPA is full. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. The specified VLAN identifier will not be added to the TCAM table. mcp-io "Try to remove some of the registered VLANs for the interface by " "changing the interface configuration. To verify the VLAN IDs currently " "in use by an interface enter the show vlans " "command." ASR1000_SPA_ETHER-3-TCAM_VLAN_ERROR 3-Error Failed to [chars] VLAN [dec] to/from interface [chars] status = [dec] The access to update the TCAM VLAN filtering table on the SPA failed. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. mcp-io LOG_STD_ACTION ASR1000_SPA_ETHER-3-TCAM_VLAN_TABLE_FULL 3-Error Failed to add VLAN [dec] to interface [chars] The TCAM VLAN filtering table on the SPA is full. The error message indicates the SPA subslot and the affected interface and the VLAN entry that failed. The specified VLAN identifier will not be added to the TCAM table. mcp-io "Try to remove some of the registered VLANs for the interface by " "changing the interface configuration. To verify the VLAN IDs currently " "in use by an interface enter the show vlans " "command." ASR900_PLATFORM-3-BP_AUTH_FAIL 3-Error Failed to Authenticate the backplane quack deivice. This device may not be a quacked properly or not CISCO manufactured. During the router boot-up we check if this router is cisco manufactured or not. If this device is not quacked properly or not CISCO manufactured this error is expected. asr900-csl LOG_STD_ACTION ASR900_PLATFORM-3-PUNT_KEEPALIVE_PROP_CREATE_ERR 3-Error Failed to create chasfs property [chars] rc=[dec] Failure occured while creating chasfs property asr900-system-rsp3 LOG_STD_ACTION ASR900_PLATFORM-3-PUNT_KEEPALIVE_PROP_SET_ERR 3-Error Failed to set chasfs property [chars] with [chars] rc=[dec] Failure occured while updating chasfs property asr900-system-rsp3 LOG_STD_ACTION ASR900_PROTECTION-3-TDL_MSG_FAIL 3-Error Failed to send the protection-physical [chars] TDL msg for protection interface [chars] and member [chars] Whenever there is any error while sending the TDL msg for binding/unbinding a physical controller with UPSR/ACR controller asr900-protection LOG_STD_ACTION ASR900_PTP-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message from PTP daemon An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from PTP daemon. asr900-ptp LOG_STD_ACTION ASR900_PTP-3-MSGINITFAIL 3-Error Failed to initalize required PTP resource: [chars] During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated. asr900-ptp LOG_STD_ACTION ASR900_RP_ATM_SPA-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED 3-Error total active atm vc per ATM SPA reached limitation of [dec] total number of active atm vc per ATM SPA has reached max limit - LOG_STD_ACTION ASR900IM-3-DIFF_IM_INSERTED 3-Error [chars] - [chars] in bay [dec] A different IM type has been inserted in the bay which previously had another IM type. If the interfaces were set to default before swap the IM will boot up fine. If not IM will goto Out-of-service state. Kindly insert the previous IM type use hw-module subslot 0/x default and then proceed with the IM swap. If not might need to reload the box for recovery - - ASR900IM-3-INCOMPATIBLE 3-Error [chars]-[dec] P1D and onwards Cu IM.... is not backward compatible with P1A/P1B/P1C Cu IM use the same build of Cu IM or reload the router to use the new build. - - ASR900IM-3-INVALID_COMBINATION 3-Error [chars] is not allowed in bay [dec] can be supported only in bays [chars] The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis. - - ASR900IM-3-INVALID_MODE 3-Error [chars] with mode [chars] is not allowed in bay [dec] can be supported only in bays [chars] The inserted IM is not supported in the specified subslot given the combination of existing IMs in the chassis. - - ASR900IM-3-UNSUPPORTED 3-Error This Interface Module is not supported in subslot [dec] The inserted IM is not supported in the specified subslot. Kindly check the supported slots for the IM type. - - ASR900IM-3-UNSUPPORTED_DYING_GASP 3-Error Command rejected Cannnot co-exist with [chars] present in subslot [dec]. Please retry after removing IM and rebooting. The inserted IM cannot co-exist in the specified subslot after enabling dying gasp internal port. Kindly check the supported slots for the IM type. - - ASR900IM-3-UNSUPPORTED_IPSEC 3-Error [chars] will not be operational in subslot [dec] after reboot due to payload encryption support with IPsec license The inserted IM will not be supported in the specified subslot after reboot due to payload encryption support with IPsec license. Kindly check the supported slots for the IM type. - - ASR900IM-3-UNSUPPORTED_PLATFORM 3-Error This Interface Module is not supported in [chars] platform The inserted IM is not supported in the specified platform - - ASR900INTF-3-UNSUPPORTED 3-Error Interface [chars] is not supported in subslot [dec] by the [chars] module The Interface specified in the error message is not supported in the specified Subslot by the version of the operating system currently running on the system. - - ASR903_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_CSB 3-Error Failed to allocate a csb Can't allocate a csb when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-3-PUNT_KEEPALIVE_ERR_ALLOC_TTY 3-Error Failed to allocate a tty Can't allocate a TTY when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-3-PUNT_KEEPALIVE_ERR_OPEN_FILE 3-Error Failed to open file: [chars] Failed to open file when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-3-PUNT_KEEPALIVE_ERR_WRITE_TO_FILE 3-Error Write to file Id [dec] failed [dec] bytes expected [dec] bytes Write to file failed when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-4-PUNT_KEEPALIVE_ERR_CLOSE_FILE 4-Warning Failed to close file with descriptor: [dec] Closing of file failed when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-4-PUNT_KEEPALIVE_ERR_GET_FILE_NAME 4-Warning Failed to get file name Could not form a file name when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-4-PUNT_KEEPALIVE_ERR_INV_FILE_ID 4-Warning Invalid file descriptor: [dec] Invalid file descriptor was found when generating punt err log asr903-cfc LOG_STD_ACTION ASR903_CFC-4-PUNT_KEEPALIVE_ERR_INV_PARAM 4-Warning Invalid parameter: [chars] Invalid parameter was passed when generating punt err log asr903-cfc LOG_STD_ACTION ASYNC_IF-0-DSR_READ_FAIL 0-Emergency Failed to read DSR state.. Failed to read DSR Data Set Ready state. IIOT_COMPONENT LOG_ERR ASYNC_IF-0-DTR_SET_FAIL 0-Emergency Failed to set DTR state.. Failed to set DTR Data Terminal Ready state. esr6k3-async LOG_ERR AT-1-NOMEM 1-Alert Could not allocate memory for [chars] at line [dec] in [chars] An internal software error occurred. atalk LOG_STD_SH_TECH_ACTION AT-2-ASSERTFAILED 2-Critical AppleTalk assertion failed: [chars] The software detected an inconsistency. Although this error is serious the router attempts to continue. AppleTalk processing might be impaired. atalk "Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative." AT-3-DOMLOOP 3-Error Loop detected on domain [dec] [[chars]] The domain router detected a routing loop. Routing loops are not allowed. The domain router runs a background loop detection process. The domain router starts this process when it receives a new zone list from a domain that is identical to the list in the main routing table and whose network range length matches that in this list. The loop detection process sends several AppleTalk NBP loopback packets. When one of these packets is received on an interface that does not belong to the original domain the domain router first shuts off all the domains involved in the loop and then shuts off all the interfaces in these domains. The loop detection does not catch all types of loops. It is your responsibility to make sure that no loop exists. atalk "Disable the cause of the routing loop. Then use the clear appletalk " "command to restart the interfaces involved." AT-3-DOMOVERFLOW 3-Error Remap range overflow for [chars] domain [dec] The remap range overflowed. If a network range cannot fit inside the atalk "Use the appletalk domain remap-range command to increase the remapping " "range. Then restart the interfaces." AT-3-INVNBPCMD 3-Error Invalid NBPtest command [chars] An unrecognized command was specified in the Name Binding Protocol NBP test facility. atalk "Enter a valid command." AT-3-NOBESTPATH 3-Error Could not compute best path for network %#A A path to the specified network could not be found. atalk "Use the show appletalk route command to verify that a path to the " "specified network exists. If it does copy the error message exactly " "as it appears and report it along with the output of the show " "appletalk route command to your technical support representative." AT-3-NOROUTE 3-Error No route to destination [atalk_address] You attempted to remove a route from the routing table by issuing the clear appletalk route command. The command failed because the route was on a directly connected interface that is it was created when you configured the router. atalk "Remove the route by reconfiguring the directly connected interface " "with which it is associated." AT-3-NOSOCKET 3-Error [chars]: client tried to open socket but failed - - - AT-3-NOSUCHNBR 3-Error No such neighbor %#a You specified a nonexistent neighbor address in a show appletalk neighbor or clear appletalk neighbor. atalk "Specify a valid neighbor address that is one that appears in the " "output of the show appletalk neighbor command." AT-3-NOTRUNNING 3-Error AppleTalk not running An AppleTalk interface that was previously shut down was restarted. atalk LOG_STD_NO_ACTION AT-3-NOVIRTUAL 3-Error [chars]: client tried to connect but no virtual network is declared A hardware or software error occurred. atalk "Copy the error message exactly as it appears and report it to your " "technical support representative." AT-3-OUTOFSYNC 3-Error [chars]: AURP connection out of sync...terminating The router detected a conflicting cable range. A router is configured with a cable range that overlaps with an existing range but does not match the entry exactly. aurp "Use the show appletalk command to identify the overlapped cable range " "and then reconfigure the misconfigured router." AT-3-SUBROUTINE_ERROR 3-Error AppleTalk error: [chars] An internal error occurred. Specifically a programming assertion in the AppleTalk networking code was violated. atalk LOG_STD_ACTION AT-4-MACIPBADCONF 4-Warning [chars]: MacIP inoperable configuration [inet] If the appletalk event-logging command is configured this message appears on the console when a MacIP server cannot begin or recover operations because of an invalid IP address configuration. This condition only occurs when the configured MacIP server's IP address is not valid on the same cable of any operable IP interface. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command. When this error occurs the MacIP configuration is considered invalid and is deleted. atalk LOG_STD_NO_ACTION AT-4-MACIPNOCABLE 4-Warning [chars]: MacIP inoperable IP interface [inet] If the appletalk event-logging command is configured this message appears on the console when a MacIP server can no longer operate due to a change in the condition of the IP interface it serves. This condition can occur if IP routing is shut down on the interface or the IP address of the interface is changed so that the MacIP server's IP address is no longer valid on the same cable. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command. atalk LOG_STD_NO_ACTION AT-5-COMPATERR1 5-Notice [chars]: AppleTalk internet compatibility mode required by %#a Although this router has neighbors that require your internetwork to observe compatibility rules AppleTalk has learned of a route that has a cable range greater than 1. This condition can cause node inconsistencies on your AppleTalk network. atalk "Upgrade the routers that support only the original AppleTalk " "specification. In the meantime observe the compatibility rules " "for AppleTalk Phase 1 and Phase 2 routers." AT-5-FDDICOMPAT 5-Notice AppleTalk FDDI neighbor %#a using obsolete FDDI addressing An attempt was made to configure an interface to have the same or a conflicting AppleTalk address or cable range as another interface on the same router. atalk "Verify that you are not specifying an AppleTalk address or cable range " "used previously on this router and reconfigure the interface." AT-5-NOSUCHROUTE 5-Notice No such route [dec] You specified a nonexistent route in a show appletalk route or clear appletalk route command. atalk "Specify a valid route that is one that appears in the output of the " "show appletalk route command." AT-5-PATHCHANGE 5-Notice Route to %#A is now using path of type [chars] on [chars] via %#a The path to a network changed because either the old path went down or the new path was better. atalk LOG_STD_NO_ACTION AT-5-RTMPSTATE 5-Notice [chars]: RTMP path to %#A via %#a now in [chars] state metric [dec] [dec] hops A new AppleTalk path has been learned. The message indicates the source of the path its distance in hops its metric and the type of path. atalk LOG_STD_NO_ACTION AT-6-BADROUTE 6-Information Route to %#A has gone bad The system did not detect a route within the required timeout period. Therefore the route is marked as bad. A network might have become unreachable for some reason perhaps because of a broken connection. This message does not necessarily indicate an error condition. atalk LOG_STD_NO_ACTION AT-6-MACIPDOWN 6-Information [chars]: MacIP server shutting down [inet] If the appletalk event-logging command is configured this message appears on the console when a MacIP server is no longer operational for any reason. MacIP servers shut down in response to MacIP configuration changes or errors or a change in the condition or configuration of an AppleTalk or IP interface for which the MacIP server is providing service. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command. atalk LOG_STD_NO_ACTION AT-6-MACIPUP 6-Information [chars]: MacIP server operational [inet] If the appletalk event-logging command is configured this message appears on the console when a MacIP server is fully initialized and is ready to accept client requests. The AppleTalk zone served by the MacIP server replaces the zone specified in the appletalk zone command. The IP address configured on the MacIP server replaces the IP address configured by the ip address command. atalk LOG_STD_NO_ACTION AT-6-NBRDELETED 6-Information Neighbor entry for %#a deleted The clear appletalk neighbor command displays this command when it completes successfully. atalk LOG_STD_NO_ACTION AT-6-PATHDEL 6-Information [chars]: AppleTalk [chars] path to %#A via %#a has been deleted An AppleTalk node sent a GetNet Info request to this router specifying an invalid network number for the source of the GetNet Info request. This situation occurs when an AppleTalk end node is moved to another network and is therefore misconfigured for the current network. atalk LOG_STD_NO_ACTION AT-6-REGPENDING 6-Information NBP registration of [chars] at [[chars]] pending A name registration call is being performed. atalk LOG_STD_NO_ACTION AT-7-BUGREPORT 7-Debug AppleTalk bug: [chars] The software detected an unexpected condition. The router takes corrective action and continues. atalk "Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative." AT-7-DEBUGMSG 7-Debug AppleTalk debug: [chars] This message is generated by a debug command and provides additional information about an AppleTalk condition. atalk "Copy the message exactly as it appears note any AppleTalk problems " "you experience and call your technical support representative." ATA-3-ATA_STATUS_ERROR 3-Error Error occurred while querying the status of ATA device. Return: [dec] stat_reg: 0x[hec] An error occurred while querying the status of ATA device. Device not responding ata-filesystem "Replace the new ATA device and retry the operation. " "If the problem persists " "1 Run 'show tech' command." ATA-6-ATA_STATUS_TIMEOUT 6-Information Timeout occurred while querying the status of ATA device. Status returned :0x[hec] event: [dec] A timeout occurred while querying the status of ATA device. - "Replace the new ATA device and retry the operation. " "If the problem persists " "1 Run 'show tech' command." ATM-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. atmcommon "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ATM-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. atmcommon "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ATM-1-NOPUSRAM 1-Alert Unit [dec] not enough interface memory The specified ATM interface hardware has run out of interface memory. - LOG_STD_SH_TECH_ACTION ATM-1-NOPUSRAM 1-Alert Unit [dec] not enough interface memory The specified ATM interface hardware has run out of interface memory. - LOG_STD_SH_TECH_ACTION ATM-2-FAILATMSWDB 2-Critical Fail malloc atm_swdb at [chars] System memory exhaustion caused an internal software error in the ATM subsystem. - "If the system exhibits any unexpected behavior as a result of " "this memory exhaustion it may need to be reset to clear the error." LOG_STD_REDUCE_ACTION ATM-2-FAILATMSWDB 2-Critical Fail malloc atm_swdb at [chars] System memory exhaustion caused an internal software error in the ATM subsystem. - "If the system exhibits any unexpected behavior as a result of " "this memory exhaustion it may need to be reset to clear the error." LOG_STD_REDUCE_ACTION ATM-3-ATM_WAVL_TREE_ERROR 3-Error ATMNode1 [chars] VCD [dec] [dec]/[dec] Node2 [chars] VCD [dec] [dec]/[dec] A software error occured. - LOG_STD_SH_TECH_ACTION ATM-3-ATM_WAVL_TREE_ERROR 3-Error ATMNode1 [chars] VCD [dec] [dec]/[dec] Node2 [chars] VCD [dec] [dec]/[dec] A software error occured. - LOG_STD_SH_TECH_ACTION ATM-3-FAILCREATEVC 3-Error ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-FAILCREATEVC 3-Error ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-FAILREMOVESERVICEPOLICYONATMVC 3-Error ATM failed to remove service policy on VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] The DSL line rate has been changed for the PVC to support the guaranteed bandwidth configured for the virtual circuits. atmcommon LOG_STD_ACTION ATM-3-FAILREMOVESERVICEPOLICYONATMVC 3-Error ATM failed to remove service policy on VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] The DSL line rate has been changed for the PVC to support the guaranteed bandwidth configured for the virtual circuits. atmcommon LOG_STD_ACTION ATM-3-FAILREMOVEVC 3-Error ATM failed to remove VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-FAILREMOVEVC 3-Error ATM failed to remove VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-ILMIINTERNALERR 3-Error [chars] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ILMIINTERNALERR 3-Error [chars] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ILMISYNCINTERNERR 3-Error [chars] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ILMISYNCINTERNERR 3-Error [chars] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ILMISYNCINTFERR 3-Error [chars] [%08X=[chars]] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ILMISYNCINTFERR 3-Error [chars] [%08X=[chars]] [chars]:[dec] Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-3-ISSU_SENDFAILED 3-Error \nATM ISSU: send message failed rc = [dec]\n The sending of a message has failed. atmcommon LOG_STD_SH_TECH_ACTION ATM-3-ISSU_SENDFAILED 3-Error \nATM ISSU: send message failed rc = [dec]\n The sending of a message has failed. atmcommon LOG_STD_SH_TECH_ACTION ATM-3-MLPDEQUEUE 3-Error MLPPP failed CosQ=[hec] MLP=[hec] OQDQ=[hec] [hec] Cause of the failure: [chars] - - - ATM-3-MLPDEQUEUE 3-Error MLPPP failed CosQ=[hec] MLP=[hec] OQDQ=[hec] [hec] Cause of the failure: [chars] - - - ATM-3-MLPOATM_ERROR 3-Error MLPoATM not configured properly on \n\ Link [chars] Bundle [chars] :[chars] The configuration of MLPPP-over-ATM MLPoATM on the ATM PVC is either incorrect or incomplete. atmcommon "Ensure that the service policy has been attached to " "the Virtual Template and that the queueing strategy on the ATM interface " "is per VC queueing and queueing algorithm is FIFO. To verify the " "configuration use the show inteface atm and " "show running-config virtual-template commands." ATM-3-MLPOATM_ERROR 3-Error MLPoATM not configured properly on \n\ Link [chars] Bundle [chars] :[chars] The configuration of MLPPP-over-ATM MLPoATM on the ATM PVC is either incorrect or incomplete. atmcommon "Ensure that the service policy has been attached to " "the Virtual Template and that the queueing strategy on the ATM interface " "is per VC queueing and queueing algorithm is FIFO. To verify the " "configuration use the show inteface atm and " "show running-config virtual-template commands." ATM-3-OUT_OF_VCDS 3-Error ATM failed to create VC on Interface [chars] The ATM subsystem ran out of internal resources necessary to create a new virtual circuit. This may indicate a software error. - LOG_STD_ACTION ATM-3-OUT_OF_VCDS 3-Error ATM failed to create VC on Interface [chars] The ATM subsystem ran out of internal resources necessary to create a new virtual circuit. This may indicate a software error. - LOG_STD_ACTION ATM-3-OVERSUBSCRIBED 3-Error Interface [chars]: Total [chars] allocation [dec][chars] exceeded maximum [chars] of [dec][chars]. A software or hardware error occurred. - LOG_STD_ACTION ATM-3-OVERSUBSCRIBED 3-Error Interface [chars]: Total [chars] allocation [dec][chars] exceeded maximum [chars] of [dec][chars]. A software or hardware error occurred. - LOG_STD_ACTION ATM-3-PPPOEOA_VCFLAG 3-Error ATM: [chars] PVC [dec]/[dec] : Error in PPPoE flag The ATM PVC PPPoE flag is still set while it should not be set. ATM uses a flag to indicate whether or not it should process PPPoE frames. In some rare conditions the flag can still be set for ATM to process PPPoE frames while it should not be. This condition can cause PPPoE frames to be processed when they should be dropped. atmcommon "In most cases no action is required as the system will set the flag " "so that ATM will not process PPPoE frames and the system " "will continue to operate normally. However If the ATM PVC " "specified in the error message is repeatedly experiencing problems " "involving PPPoE unconfigure all commands under the PVC " "and remove and then reconfigure the PVC. Enter the " "interface atm interface.subinterface-number " "command in global configuration mode to enter atm interface " "configuration mode. Then specify the PVC you would like to " "unconfigure and enter the no encapsulation " "command. Specify the PVC you just unconfigured then reconfigure " "the PVC using the encapsulation command." ATM-3-PPPOEOA_VCFLAG 3-Error ATM: [chars] PVC [dec]/[dec] : Error in PPPoE flag The ATM PVC PPPoE flag is still set while it should not be set. ATM uses a flag to indicate whether or not it should process PPPoE frames. In some rare conditions the flag can still be set for ATM to process PPPoE frames while it should not be. This condition can cause PPPoE frames to be processed when they should be dropped. atmcommon "In most cases no action is required as the system will set the flag " "so that ATM will not process PPPoE frames and the system " "will continue to operate normally. However If the ATM PVC " "specified in the error message is repeatedly experiencing problems " "involving PPPoE unconfigure all commands under the PVC " "and remove and then reconfigure the PVC. Enter the " "interface atm interface.subinterface-number " "command in global configuration mode to enter atm interface " "configuration mode. Then specify the PVC you would like to " "unconfigure and enter the no encapsulation " "command. Specify the PVC you just unconfigured then reconfigure " "the PVC using the encapsulation command." ATM-3-REJECTVC 3-Error ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-REJECTVC 3-Error ATM failed to create VCVCD=[dec] VPI=[dec] VCI=[dec] on Interface [chars] Cause of the failure: [chars] - - - ATM-3-UNSUPPORTED_QOS_PARAMS 3-Error ATM failed to create VC on Interface [chars] Either the configuration contains invalid traffic shaping parameters or the software ran out of rate queues. - "Check the configuration for errors." ATM-3-UNSUPPORTED_QOS_PARAMS 3-Error ATM failed to create VC on Interface [chars] Either the configuration contains invalid traffic shaping parameters or the software ran out of rate queues. - "Check the configuration for errors." ATM-4-ILMICONFIGCHANGE 4-Warning ILMI[chars]: Restarting ATM signalling and ILMI. Peer Configuration change detected. Configuration of adjacent peer device has been changed. - "Wait for the interface to restart itself." ATM-4-ILMICONFIGCHANGE 4-Warning ILMI[chars]: Restarting ATM signalling and ILMI. Peer Configuration change detected. Configuration of adjacent peer device has been changed. - "Wait for the interface to restart itself." ATM-4-ILMIKEEPALIVEFAIL 4-Warning ILMI[chars]: Restarting ATM signalling and ILMI. Keepalive failure detected. Adjacent peer device is not responding to ILMI Keepalive polling. - "Check the connection of the ATM interface and the status of the " "adjacent peer device. Correct them if neccessary. Wait and check " "if ILMI Keepalive comes up again. If the problem persists " "copy this warning message exactly as it appears and report it to " "your technical support representative." ATM-4-ILMIKEEPALIVEFAIL 4-Warning ILMI[chars]: Restarting ATM signalling and ILMI. Keepalive failure detected. Adjacent peer device is not responding to ILMI Keepalive polling. - "Check the connection of the ATM interface and the status of the " "adjacent peer device. Correct them if neccessary. Wait and check " "if ILMI Keepalive comes up again. If the problem persists " "copy this warning message exactly as it appears and report it to " "your technical support representative." ATM-4-ILMISYNCINTFWARN 4-Warning [chars] [%08X=[chars]] [chars]:[dec] Recoverable Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-4-ILMISYNCINTFWARN 4-Warning [chars] [%08X=[chars]] [chars]:[dec] Recoverable Internal Error see message occurs during ILMI Primary to Secondary Sync as LOG_STD_SH_TECH_ACTION ATM-4-ISSU_INCOMPATIBLE 4-Warning \natm-issu-compat: returned FALSE The compatibility checking has failed atmcommon LOG_STD_SH_TECH_ACTION ATM-4-ISSU_INCOMPATIBLE 4-Warning \natm-issu-compat: returned FALSE The compatibility checking has failed atmcommon LOG_STD_SH_TECH_ACTION ATM-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The transform has failed. atmcommon LOG_STD_SH_TECH_ACTION ATM-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The transform has failed. atmcommon LOG_STD_SH_TECH_ACTION ATM-4-MTUCALLMISMATCH 4-Warning Call from: \n ATM NSAP - [chars]\n has mismatched PDU size - forward size is [dec]\n - backward size is [dec]\n int [chars] PDU size [chars] [chars] The calling or called party has a maximum transmission unit MTU size - "Either change the configured MTU size on the current interface to that " "of the caller's or called party's interface or change the caller's or " "called party's interface to match the current interface." ATM-4-MTUCALLMISMATCH 4-Warning Call from: \n ATM NSAP - [chars]\n has mismatched PDU size - forward size is [dec]\n - backward size is [dec]\n int [chars] PDU size [chars] [chars] The calling or called party has a maximum transmission unit MTU size - "Either change the configured MTU size on the current interface to that " "of the caller's or called party's interface or change the caller's or " "called party's interface to match the current interface." ATM-4-STUCK_VCD 4-Warning clearing stuck VCD [dec] from map on [chars] A SVC map entry has a stuck VCD attached to it which has been previously cleared in the driver. - "No action required as the stuck VCD condition is detected " "and cleared." ATM-4-STUCK_VCD 4-Warning clearing stuck VCD [dec] from map on [chars] A SVC map entry has a stuck VCD attached to it which has been previously cleared in the driver. - "No action required as the stuck VCD condition is detected " "and cleared." ATM-4-UNMATCHUNIVERSION 4-Warning [dec]/[dec]/[dec]:[dec]: [chars]. Please verify peer UNI version The ATM peer equipment appears to be running an old version of ATM UNI. Communication with it is not possible. - "The peer equipment needs to be upgraded in " "order to communicate with this system." ATM-4-UNMATCHUNIVERSION 4-Warning [dec]/[dec]/[dec]:[dec]: [chars]. Please verify peer UNI version The ATM peer equipment appears to be running an old version of ATM UNI. Communication with it is not possible. - "The peer equipment needs to be upgraded in " "order to communicate with this system." ATM-4-VPIVCIRANGE 4-Warning VPI/VCI range parameters are dis-joint on [chars] MinSvccVci > MaxVci after negotiation with the peer through ILMI. - "Disable auto-cinfiguration on both sides and change the " "port configuration appropriately so that SVCCs can be setup." ATM-4-VPIVCIRANGE 4-Warning VPI/VCI range parameters are dis-joint on [chars] MinSvccVci > MaxVci after negotiation with the peer through ILMI. - "Disable auto-cinfiguration on both sides and change the " "port configuration appropriately so that SVCCs can be setup." ATM-5-ATMSOFTSTART 5-Notice Restarting ATM signalling and ILMI on [chars]. The command just entered causes ATM Soft Restart. - "Stand by and let ATM Signalling and ILMI to restart." ATM-5-ATMSOFTSTART 5-Notice Restarting ATM signalling and ILMI on [chars]. The command just entered causes ATM Soft Restart. - "Stand by and let ATM Signalling and ILMI to restart." ATM-5-ILMIACCFILTER 5-Notice New access filter setting will be applied to registration of new addresses on [chars]. The command just entered sets up new ilmi access filter for address registration. It only affects new addresses to be registered. The addresses already registered will not be affected. - "Enter the shutdown and no shutdown commands on this interface to " "restart address registration if need to remove addresses already " "registered but not permitted by the new access filter." ATM-5-ILMIACCFILTER 5-Notice New access filter setting will be applied to registration of new addresses on [chars]. The command just entered sets up new ilmi access filter for address registration. It only affects new addresses to be registered. The addresses already registered will not be affected. - "Enter the shutdown and no shutdown commands on this interface to " "restart address registration if need to remove addresses already " "registered but not permitted by the new access filter." ATM-5-ILMIADDREG 5-Notice Address registration on [chars] is enabled. The command just entered enables atm address registration. - "No action required." ATM-5-ILMIADDREG 5-Notice Address registration on [chars] is enabled. The command just entered enables atm address registration. - "No action required." ATM-5-ILMIDEFACCFILTER 5-Notice New global default access filter setting will be applied to registration of new addresses on interfaces using global default access filter. The command just entered sets up new global default access filter for addres registration. It only affects new addresses to be registered on interfaces using the global default. The addresses already registered will not be affected. - "Enter the shutdown and no shutdown commands on desired " "interfaces to restart address registration if need to remove addresses " "already registered but not permitted by the new global " "default access filter." ATM-5-ILMIDEFACCFILTER 5-Notice New global default access filter setting will be applied to registration of new addresses on interfaces using global default access filter. The command just entered sets up new global default access filter for addres registration. It only affects new addresses to be registered on interfaces using the global default. The addresses already registered will not be affected. - "Enter the shutdown and no shutdown commands on desired " "interfaces to restart address registration if need to remove addresses " "already registered but not permitted by the new global " "default access filter." ATM-5-ILMIINTFREDUNDENCY 5-Notice ILMI[chars]: [chars] Informational Message for ILMI Redundency Support as LOG_STD_SH_TECH_ACTION ATM-5-ILMIINTFREDUNDENCY 5-Notice ILMI[chars]: [chars] Informational Message for ILMI Redundency Support as LOG_STD_SH_TECH_ACTION ATM-5-ILMIREDUNDENCY 5-Notice [chars] Informational Message for ILMI Redundency Support as LOG_STD_SH_TECH_ACTION ATM-5-ILMIREDUNDENCY 5-Notice [chars] Informational Message for ILMI Redundency Support as LOG_STD_SH_TECH_ACTION ATM-5-UPDOWN 5-Notice Interface [chars] Changing autovc [dec]/[dec] to [chars] The ATM Auto VC is either created removed activated \n\ or deactivated. - "No action required if status change is intended\n\ otherwise the cause for status change may deserve to be noticed.\n\ The shut and no shut CLI command deactivates/activates VC." ATM-5-UPDOWN 5-Notice Interface [chars] Changing autovc [dec]/[dec] to [chars] The ATM Auto VC is either created removed activated \n\ or deactivated. - "No action required if status change is intended\n\ otherwise the cause for status change may deserve to be noticed.\n\ The shut and no shut CLI command deactivates/activates VC." ATM-6-AUTOPPP 6-Information ATM[chars]: VCVCD=[dec] VPI=[dec] VCI=[dec] Auto Detected Encap Type is [chars]. ATM VC AutoPPP Encapsulation Type has been changed automatically`. atmcommon "don't do anything." ATM-6-AUTOPPP 6-Information ATM[chars]: VCVCD=[dec] VPI=[dec] VCI=[dec] Auto Detected Encap Type is [chars]. ATM VC AutoPPP Encapsulation Type has been changed automatically`. atmcommon "don't do anything." ATM-6-ILMIAUTOCFGALREADY 6-Information ILMI[chars]: Auto-configuration already enabled. Atm auto-configuration has been enabled already. 'atm auto-configuration' command just entered is ignored. - "No action required." ATM-6-ILMIAUTOCFGALREADY 6-Information ILMI[chars]: Auto-configuration already enabled. Atm auto-configuration has been enabled already. 'atm auto-configuration' command just entered is ignored. - "No action required." ATM-6-ILMIAUTOCFGENABLEERR 6-Information ILMI[chars]: Auto-configuration cannot be enabled. Auto-configuration cannot be enabled if there are some conflicting configuration on an interface. Like if there are VCs with vpi > 255 auto-configuration cannot be done till these VCs are removed as with auto-configuration enabled vpi > 255 cannot be supported. - "Undo the conflicting configuration on the interface for " "this command to succeed." ATM-6-ILMIAUTOCFGENABLEERR 6-Information ILMI[chars]: Auto-configuration cannot be enabled. Auto-configuration cannot be enabled if there are some conflicting configuration on an interface. Like if there are VCs with vpi > 255 auto-configuration cannot be done till these VCs are removed as with auto-configuration enabled vpi > 255 cannot be supported. - "Undo the conflicting configuration on the interface for " "this command to succeed." ATM-6-ILMINOAUTOCFG 6-Information ILMI[chars]: Auto-configuration is disabled current The command just entered causes auto-configuration to be disabled the most recently entered interface parameters will be used at next interface restart. - "Be aware of what parameteres have been configured." ATM-6-ILMINOAUTOCFG 6-Information ILMI[chars]: Auto-configuration is disabled current The command just entered causes auto-configuration to be disabled the most recently entered interface parameters will be used at next interface restart. - "Be aware of what parameteres have been configured." ATM-6-ILMINOAUTOCFGALREADY 6-Information ILMI[chars]: Auto configuration already disabled. Atm auto-configuration has been enabled already. 'no atm auto-configuration' command just entered is ignored. - "No action required." ATM-6-ILMINOAUTOCFGALREADY 6-Information ILMI[chars]: Auto configuration already disabled. Atm auto-configuration has been enabled already. 'no atm auto-configuration' command just entered is ignored. - "No action required." ATM-6-ILMITERMINATINGPORT 6-Information ILMI[chars]: This command does not apply to internal terminating port. Internal terminating does not need to be configured with this command. The command just entered is ignored. - "No action required." ATM-6-ILMITERMINATINGPORT 6-Information ILMI[chars]: This command does not apply to internal terminating port. Internal terminating does not need to be configured with this command. The command just entered is ignored. - "No action required." ATM-6-PVC_STATE_CHANGE 6-Information ATM[chars]: PVCVCD=[dec] VPI=[dec] VCI=[dec] state changed to [chars]. ATM PVC status has changed. - LOG_NO_ACTION ATM-6-PVC_STATE_CHANGE 6-Information ATM[chars]: PVCVCD=[dec] VPI=[dec] VCI=[dec] state changed to [chars]. ATM PVC status has changed. - LOG_NO_ACTION ATMCORE_RED-2-INTERNAL_CRITICAL 2-Critical [chars] The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE_RED-3-INTERNAL_ERROR 3-Error [chars] The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE_RED-4-INTERNAL_WARNING 4-Warning [chars] The ATM core redundancy subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE-2-INTERNAL_CRITICAL 2-Critical [chars] The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE-3-INTERNAL_ERROR 3-Error [chars] The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE-4-ATM_SYS_ERROR 4-Warning [chars] The ATM core subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMCORE-4-CONFIG_ERROR 4-Warning Configuration Error: [chars] This message indicates a configuration error. The message will display more specific information about the problem location. - "Change the configuration to correct the error." ATMCORE-4-INTERNAL_WARNING 4-Warning [chars] This warning is generated by the ATM core subsystem to the user. This could arise because the user request may not be granted due to some existing configuration on the device. This message serves as an alert to the user. This message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_CUG_DELETE_FAILED 3-Error ATMSIG[chars] A software error occurred during removal of a member from a\n\ closed user group. Other error messages appearing\n\ immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_CUG_INSERT_FAILED 3-Error ATMSIG[chars] A software error occurred during addition of a member to a\n\ closed user group. Other error messages appearing\n\ immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_LISTEN_FAILED_DUP 3-Error Duplicate LISTEN by [chars] for existing NSAP [chars] owned by [chars] An application attempted to either LISTEN on an NSAP owned by \n\ another application or to LISTEN for the same NSAP twice - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_PRTY_DELETE_FAILED 3-Error ATMSIG[chars] [dec][dec] - %04d/%02d avl prty del failed:svc 0x[hec] party 0x[hec] A software error occurred during removal of a party from a\n\ point-to-multipoint call. Other error messages appearing \n\ immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_PRTY_INSERT_FAILED 3-Error ATMSIG[chars] [dec][dec] - %04d/%02d avl prty ins failed:svc 0x[hec] party 0x[hec] A software error occurred during addition of a party to a\n\ point-to-multipoint call. Other error messages appearing\n\ immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_SVC_DELETE_FAILED 3-Error ATMSIG[chars] [dec][dec] - %04d/%02d SVC wavl del failed:svc 0x[hec] A software error occurred during closure of an SVC. Other error\n\ messages appearing immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-ATMSIG_SVC_INSERT_FAILED 3-Error ATMSIG[chars] [dec][dec] - %04d/%02d SVC wavl ins failed:svc 0x[hec] A software error occurred during creation of an SVC. Other error\n\ messages appearing immediately prior to this one may be related. - LOG_STD_SH_TECH_ACTION ATMSIG-3-DBINITFAIL 3-Error Signalling control block initialization failure [chars] An internal software or resource error occurred - LOG_STD_SH_TECH_ACTION ATMSIG-3-ENQFAIL 3-Error process_enqueue failed [chars] An internal software error occurred while handling a user request. - LOG_STD_SH_TECH_ACTION ATMSIG-3-FAIL1STHALFLEG 3-Error 1st halfLeg failed [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION ATMSIG-3-FAIL2NDHALFLEG 3-Error 2nd halfLeg failed [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION ATMSIG-3-FAILASSERT 3-Error Assertion failed: [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION ATMSIG-3-FAILHALFLEGREM 3-Error halfLeg removal failed [chars] An internal software error occurred. This message should only\n\ be displayed when verbose debugging is enabled for an SVC. - LOG_STD_SH_TECH_ACTION ATMSIG-3-FAILXCONN 3-Error Xconnect failed [chars] An internal software error occurred during installation of an\n\ SVC cross-connect. - LOG_STD_SH_TECH_ACTION ATMSIG-3-INVPNNIMSG 3-Error Invalid msg from routing/pnni : [chars] This message indicates an error in the PNNI routing subsystem.\n\ It could be caused by an internal software error or by bad\n\ control information received from peer equipment. The message\n\ will contain additional information that can help locate the\n\ cause. Any message with 'NULL' probably indicates a problem\n\ with this system others probably point at the peer equipment. - "Check this system and the peer equipment for any obvious errors. " LOG_STD_RECUR_ACTION ATMSIG-3-NOCALLREF 3-Error Cannot find a Callref value to allocate: [chars] This indicates an internal software error probably including\n\ memory exhaustion. - LOG_STD_SH_TECH_ACTION ATMSIG-3-NOSVC 3-Error no SVC [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION ATMSIG-3-PNNI_TRACE_INTERNAL 3-Error [chars] An internal software error or unexpected condition occured during\n\ PNNI Connection/Path Trace related processing - - ATMSIG-4-CONFIG_ERROR 4-Warning Configuration Error: [chars] [chars] This message indicates a configuration error in the ATM Signaling\n\ subsystem. The message will display more specific information\n\ about the problem location. - "Change the configuration to correct the error." ATMSPA-2-INITFAIL 2-Critical [chars] - Init Failed return code: [dec] The SPA failed to complete hardware initialization. One of the devices in the SPA failed to initialize successfully. Information about the failed device is specified in the message text on the console or in the system log. - "Please power down and reseat the indicated SPA card. If the condition " "persists copy the error message exactly as it appears. Next research " "and attempt to resolve the issue using the SPA hardware troubleshooting " "documentation as well as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ATMSPA-3-ATM_SPA_AUTOVC_FAIL 3-Error [chars]: atm autovc discovery configuration failed reason: [chars] A command to configure the atm autovc discovery on an atm interface has failed spa-atm-all LOG_STD_ACTION ATMSPA-3-DATA_ERROR 3-Error [chars] Error 0x[hec] [chars] A datapath protocol violation or sequence error has been detected. - "The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION ATMSPA-3-FATAL_ERROR 3-Error occurred on [chars]. Resetting SPA The SPA has been reset due to a critical error in one of its devices. The error could either be a single occurrence of an event or multiple occurrences within a period of time. The message text on the console or in the system log provides more information on the specific nature of the error. spa-atm-all "If the SPA is reset more than once copy the error " "message exactly as it appears. Next research and attempt to resolve the " "issue using the SPA hardware troubleshooting documentation as well " "as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ATMSPA-3-FPD_VER_DEPENDENCY_NOTE 3-Error Cannot perform the requested FPD update operation because [chars] in subslot [dec]/[dec] has incompatible HW version [dec].[dec] with FPD image version [dec].[dec] for FPD ID [dec]. Only image version greater than [dec].[dec] can be used in the update operation of [chars] with HW version greater than [dec].[dec]. The version of the FPD image from the FPD image bundle or package is not compatible with the HW version of the target card spa-atm-all LOG_STD_ACTION ATMSPA-3-GEN_ERROR 3-Error [chars] Error 0x[hec] [chars] The specified error has been detected. - LOG_STD_SH_TECH_ACTION ATMSPA-3-HW_ERROR 3-Error [chars] Error 0x[hec] [chars] The specified hardware error has been detected. - "The message text on the console or in the " "system log provides more information " "on the specific nature of the error. " LOG_STD_SH_TECH_ACTION ATMSPA-3-KEEPALIVE_FAILURE 3-Error occurred on [chars]. Resetting SPA One of the devices of the SPA failed to respond to keepalives due to which SPA has been reset. The message text on the console or in the system log provides more information on which device failed to respond. spa-atm-all "If the SPA is reset more than once copy the error " "message exactly as it appears. Next research and attempt to resolve the " "issue using the SPA hardware troubleshooting documentation as well " "as the tools and utilities provided at " BUG_TOOLKIT "If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " TAC_CASE_OPEN " or contact your Cisco technical " "support representative. Be sure to provide the information you have " "gathered and show tech-support to your support " "representative or attach it to your case" ATMSPA-3-QOS_ALLOC_FAILED 3-Error [chars] [chars] [chars]: [dec] Traffic shaping parameters could not be configured because the number of unique shaping parameters that are configured on the PVCs or PVPs in this specified ATM SPA is over the maximum limit. The maximum number of unique shaping parameters that can be configured on the PVCs or PVPs is 4096. spa-atm-all "Ensure that the total number of unique shaping parameters " "that are configured on both PVCs and PVPs does not exceed " "the maximum limit of 4096." ATMSPA-3-SW_ERROR 3-Error [chars] Error 0x[hec] [chars] The specified software error has been detected. - LOG_STD_SH_TECH_ACTION ATMSPA-3-VCQ_ERROR 3-Error [chars]: VC queue configuration failed due to un-initialized queue table global identifier [dec] Software configuration of a VC queue failed due to un-initialized queue table. - "Attempt to perform a soft OIR operation by entering the command " "that is described in the shared port adapter software configuration " "guide. If the condition persists copy the error message exactly as it " "appears and report it to your technical support representative. " "Also supply a 'show tech-support' at that time." ATMSPA-4-SETUPVC 4-Warning Interface [chars] VC [dec] setup failed reason = [dec] A command to setup a VC has failed on RP. spa-atm-all "The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ATMSPA-4-TEARDOWNVC 4-Warning Interface [chars] VC [dec] teardown failed reason = [dec] A command to remove a VC config has failed on RP. spa-atm-all "The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ATMSPA-4-VCSETUP 4-Warning [chars]: VC setup command received on the LC for an existing VC VCD [dec] A command to set up a VC has been received for a VC that has already been set up. The VC has already been configured by a previous setup VC command from the RP. A duplicate setup command may indicate that the RP did not receive a response from the LC for the previous setup command. - LOG_STD_NO_ACTION ATMSPA-4-VCTEARDOWN 4-Warning [chars]: VC tear down command received on the LC for a non-existing VC VCD [dec] The VC does not exist on the LC. Most likely it has been torn down by a previous teardown command from RP. A duplicate teardown command may indicate that the RP did not receive a response from the LC for the previous teardown command. - LOG_STD_NO_ACTION ATMSPA-4-VPSETUP 4-Warning [chars]: VP setup command received on the LC for an existing VP VPI [dec] A command to set up a VP has been received for a VP that has already been set up. The VP has already been configured by a previous setup VP command from the RP. A duplicate setup command may indicate that the RP did not receive a response from the LC for the previous setup command. - LOG_STD_NO_ACTION ATMSPA-4-VPTEARDOWN 4-Warning [chars]: VP tear down command received on the LC for a non-existing VP VPI [dec] The VP does not exist on the LC. Most likely it has been torn down by a previous teardown command from RP. A duplicate teardown command may indicate that the RP did not receive a response from the LC for the previous teardown command. - LOG_STD_NO_ACTION ATMSSCOP-3-SSCOPERR 3-Error INIT SSCOP -\nIntf : [chars] Event : [chars] State : [chars]. A software error occurred in the ATM SSCOP subsystem. - LOG_STD_SH_CMD_ACTION ATMSSCOP-4-UNMATCHUNIVERSION 4-Warning [chars]: [chars]. Please verify peer UNI version The ATM peer equipment appears to be running an old version of\n\ ATM UNI. Communication with it is not possible. - "The ATM peer equipment may need attention. \Please verify its UNI version is at least 3.1 and upgrade if necessary." ATMSSCOP-5-SSCOPINIT 5-Notice - Intf : [chars] Event : [chars] State : [chars]. This message indicates a routine step of the ATM SSCOP\n\ initialization sequence. - LOG_STD_NO_ACTION ATOM_HA-3-RECOVERY 3-Error [chars] AToM Manager High Availability recovery failed. xconnect LOG_STD_ACTION ATOM_HA-3-RECOVERY 3-Error [chars] AToM Manager High Availability recovery failed. xconnect LOG_STD_ACTION ATOM_HA-3-UPDATE 3-Error [chars] AToM Manager High Availability update failed. xconnect LOG_STD_ACTION ATOM_HA-3-UPDATE 3-Error [chars] AToM Manager High Availability update failed. xconnect LOG_STD_ACTION ATOM_NP_CLIENT-3-INFO 3-Error [chars] ATOM NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." ATOM_NP_CLIENT-3-NOMEM 3-Error [chars] ATOM NP Client failed to initialize properly which will result in\n\ improper operation of Any Transport Over MPLS feature vsp-mid "This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." ATOM_NP_CLIENT-4-WARN 4-Warning [chars] [dec] [chars] AToM Entry could not be added because:\n\ 1. Entry passed is invalid. vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." ATOM_SEG-3-CHUNKFREE 3-Error Error freeing [chars] ATOM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-CHUNKFREE 3-Error Error freeing [chars] ATOM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-ILLEGALUPD 3-Error Illegal label [dec] update [chars] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-ILLEGALUPD 3-Error Illegal label [dec] update [chars] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-NOTSUPP 3-Error Unsupported update [chars] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-NOTSUPP 3-Error Unsupported update [chars] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-UNSUPPORTEDADDR 3-Error Unsupported address type [dec] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_SEG-3-UNSUPPORTEDADDR 3-Error Unsupported address type [dec] AToM Segment Handler error mpls-mfi LOG_STD_ACTION ATOM_TRANS-3-CONSISTENCY 3-Error [chars] An action attempted by the layer 2 transport over MPLS implementation encountered an unexpected condition xconnect LOG_STD_ACTION ATOM_TRANS-3-CONSISTENCY 3-Error [chars] An action attempted by the layer 2 transport over MPLS implementation encountered an unexpected condition xconnect LOG_STD_ACTION ATOM_TRANS-3-INIT_FAIL 3-Error Failed to start AToM Manager Failed to start and initialize AToM Manager. xconnect LOG_STD_ACTION ATOM_TRANS-3-INIT_FAIL 3-Error Failed to start AToM Manager Failed to start and initialize AToM Manager. xconnect LOG_STD_ACTION ATOM_TRANS-3-LABEL_ALLOC_FAIL 3-Error Failed to allocate local label for peer:[inet] vcid:[dec] Failed to allocate local label for specified AToM VC. xconnect LOG_STD_ACTION ATOM_TRANS-3-LABEL_ALLOC_FAIL 3-Error Failed to allocate local label for peer:[inet] vcid:[dec] Failed to allocate local label for specified AToM VC. xconnect LOG_STD_ACTION ATOM_TRANS-3-XDM_CREATE 3-Error Failed to create XDM - rc [dec] ATOM Manager was unable to create a Dispatch Manager instance for event handling. xconnect LOG_STD_ACTION ATOM_TRANS-3-XDM_CREATE 3-Error Failed to create XDM - rc [dec] ATOM Manager was unable to create a Dispatch Manager instance for event handling. xconnect LOG_STD_ACTION ATOM_TRANS-4-CONFIG 4-Warning [chars] AToM pseudowire uses undesirable configuration. xconnect LOG_STD_ACTION ATOM_TRANS-4-CONFIG 4-Warning [chars] AToM pseudowire uses undesirable configuration. xconnect LOG_STD_ACTION ATOM_TRANS-4-PW_MAX_REACHED 4-Warning [chars] Pseudowire maximum limit reached for the L2 subscriber author group xconnect LOG_STD_ACTION ATOM_TRANS-4-PW_MAX_REACHED 4-Warning [chars] Pseudowire maximum limit reached for the L2 subscriber author group xconnect LOG_STD_ACTION ATOM_TRANS-5-DISPOSITION_DISABLED 5-Notice [chars] Disposition disabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-DISPOSITION_DISABLED 5-Notice [chars] Disposition disabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-DISPOSITION_ENABLED 5-Notice [chars] Disposition enabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-DISPOSITION_ENABLED 5-Notice [chars] Disposition enabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-IMPOSITION_DISABLED 5-Notice [chars] Imposition disabled specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-IMPOSITION_DISABLED 5-Notice [chars] Imposition disabled specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-IMPOSITION_ENABLED 5-Notice [chars] Imposition enabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-IMPOSITION_ENABLED 5-Notice [chars] Imposition enabled for specified AToM VC. xconnect LOG_STD_NO_ACTION ATOM_TRANS-5-PW_WATERMARK_LIMIT 5-Notice [chars] Pseudowire max watermark limit reached for the L2 subscriber author group xconnect LOG_STD_ACTION ATOM_TRANS-5-PW_WATERMARK_LIMIT 5-Notice [chars] Pseudowire max watermark limit reached for the L2 subscriber author group xconnect LOG_STD_ACTION ATOM_TRANS-6-ATOM_NO_ROUTER_ID 6-Information [chars] No router ID is available for AToM to use and this will impact pseudowire VCCV. Please enable \l2 router-id
\ or enable an LDP router ID if you wish VCCV to be operational. xconnect LOG_STD_ACTION ATOM_TRANS-6-ATOM_NO_ROUTER_ID 6-Information [chars] No router ID is available for AToM to use and this will impact pseudowire VCCV. Please enable \l2 router-id
\ or enable an LDP router ID if you wish VCCV to be operational. xconnect LOG_STD_ACTION ATTN-2-MBOX_REG_FAIL 2-Critical return code [dec] Registration of handler function for mailbox event failed mailbox event failed. cpp-ucode LOG_STD_ACTION ATTN-2-PROXY_INIT_FAIL_IPC_REG 2-Critical return code [dec] Initialization of attention proxy failed due to error registering IPC handler function. cpp-ucode LOG_STD_ACTION ATTN-3-PROXY_IPC_ALLOC_FAILED 3-Error [chars] Allocation of an IPC packet buffer by the attention proxy failed. cpp-ucode LOG_STD_ACTION ATTN-3-PROXY_IPC_SEND_FAILED 3-Error [chars] Transmission of an IPC message by the attention proxy failed. cpp-ucode LOG_STD_ACTION ATTN-3-PROXY_UNHANDLED_MSG 3-Error subtype [dec] Attention proxy received a message with an unknown subtype. cpp-ucode LOG_STD_ACTION ATTN-3-SYNC_TIMEOUT 3-Error msecs since last timeout %llu missing packets [dec] Attention sync command timed out. cpp-ucode LOG_STD_ACTION AUDIT-1-FILE_ROLLOVER 1-Alert Audit File Roll-over: [dec] Audit Circular File Rolled Over. - "Increase Audit filesize." AUDIT-3-FILE_RESIZE_ERR 3-Error Cannot resize Audit file. File system error while resizing the audit file. - "Check DISK filesystems on the router." AUDIT-3-FILE_WRITE_ERR 3-Error Cannot write to Audit file. File system error while writing to the audit file. - "Check DISK filesystems on the router." AUDIT-3-NOFILE 3-Error Cannot create Audit file. File system error while creating the audit file. - "Check DISK filesystems on the router." AUDIT-3-NOPROC 3-Error Cannot create Audit process. Insufficient internal resource available to create process. - "Check available memory on router." AUDIT-5-AUDIT_DISABLED 5-Notice Auditing disabled Audit was disabled on the router. - "Check if Audit was disabled by someone authorized to do so" AUDIT-5-AUDIT_ENABLED 5-Notice Auditing enabled Audit was enabled on the router. - "Audit logs can be verified if changes are valid" AUDIT-5-FILESYSTEM 5-Notice Filesystem changed. Hash: [chars] FLASH/DISK Filesystems on the router changed. - "Check if it is a valid change." AUDIT-5-HARDWARE_CONFIG 5-Notice Hardware changed. Hash: [chars] Hardware on the router changed. - "Check if it is a valid change." AUDIT-5-RUN_CONFIG 5-Notice Running Configuration changed. Hash: [chars] Running Config on the router changed. - "Check if it is a valid change in config." AUDIT-5-RUN_VERSION 5-Notice Running Version changed. Hash: [chars] Running Version on the router changed. - "Check if it is a valid change." AUDIT-5-STARTUP_CONFIG 5-Notice Startup Configuration changed. Hash: [chars] Startup config on the router changed. - "Check if it is a valid change." AUTHMGR-0-CONFIG_CORRUPT 0-Emergency Checksummed interface configuration corruption detected. Interface configuration field was modified unexpectedly. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-0-CONFIG_CORRUPT 0-Emergency Checksummed interface configuration corruption detected. Interface configuration field was modified unexpectedly. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-4-ILLEGAL_TRACE_REQ 4-Warning Component ID [dec] not registered. Attempt to log a message with unregistered ID. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-4-ILLEGAL_TRACE_REQ 4-Warning Component ID [dec] not registered. Attempt to log a message with unregistered ID. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-4-UNAUTH_MOVE 4-Warning [chars] MAC address [enet] from [chars] to [chars] Move while not authenticated on old IDB dot1x-ios LOG_STD_NO_ACTION AUTHMGR-4-UNAUTH_MOVE 4-Warning [chars] MAC address [enet] from [chars] to [chars] Move while not authenticated on old IDB dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-FAIL 5-Notice Authorization failed or unapplied for client [enet] on Interface [chars] Authorization was unsuccessful. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-FAIL 5-Notice Authorization failed or unapplied for client [enet] on Interface [chars] Authorization was unsuccessful. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-MACMOVE 5-Notice MAC address [enet] moved from Interface [chars] to Interface [chars] Client has moved to a new interface without logging off on the previous one. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-MACMOVE 5-Notice MAC address [enet] moved from Interface [chars] to Interface [chars] Client has moved to a new interface without logging off on the previous one. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-MACREPLACE 5-Notice MAC address [enet] on Interface [chars] is replaced by MAC [enet] A new client has triggered a violation causing an existing client to be replaced dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-MACREPLACE 5-Notice MAC address [enet] on Interface [chars] is replaced by MAC [enet] A new client has triggered a violation causing an existing client to be replaced dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-SECURITY_VIOLATION 5-Notice Security violation on the interface [chars] new MAC address [enet] is seen. A host on the specified interface is attempting to gain access into the network or is trying to authenticate in a host mode that does not support the number of hosts attached. This is treated as a security violation and the port has been error-disabled. dot1x-ios "Ensure that the port is configured to support the " "number of hosts attached. Enter the " "shutdown command followed by " "no shutdown command to restart " "the port." AUTHMGR-5-SECURITY_VIOLATION 5-Notice Security violation on the interface [chars] new MAC address [enet] is seen. A host on the specified interface is attempting to gain access into the network or is trying to authenticate in a host mode that does not support the number of hosts attached. This is treated as a security violation and the port has been error-disabled. dot1x-ios "Ensure that the port is configured to support the " "number of hosts attached. Enter the " "shutdown command followed by " "no shutdown command to restart " "the port." AUTHMGR-5-START 5-Notice Starting '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars] Starting an authentication method dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-START 5-Notice Starting '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars] Starting an authentication method dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-SUCCESS 5-Notice Authorization succeeded for client [enet] on Interface [chars] Authorization was successful. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-SUCCESS 5-Notice Authorization succeeded for client [enet] on Interface [chars] Authorization was successful. dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-VLANASSIGN 5-Notice VLAN [dec] assigned to Interface [chars] AuditSessionID [chars] VLAN assignment dot1x-ios LOG_STD_NO_ACTION AUTHMGR-5-VLANASSIGN 5-Notice VLAN [dec] assigned to Interface [chars] AuditSessionID [chars] VLAN assignment dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-FAILOVER 7-Debug Failing over from '[chars]' for client [chars] on Interface [chars] Failing over from the current authentication method dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-FAILOVER 7-Debug Failing over from '[chars]' for client [chars] on Interface [chars] Failing over from the current authentication method dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-NOMOREMETHODS 7-Debug Exhausted all authentication methods for client [chars] on Interface [chars] All available authentication methods have been tried dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-NOMOREMETHODS 7-Debug Exhausted all authentication methods for client [chars] on Interface [chars] All available authentication methods have been tried dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-STOPPING 7-Debug Stopping '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars] Stopping the current authentication method dot1x-ios LOG_STD_NO_ACTION AUTHMGR-7-STOPPING 7-Debug Stopping '[chars]' for client [enet] on Interface [chars] AuditSessionID [chars] Stopping the current authentication method dot1x-ios LOG_STD_NO_ACTION AUTO_IP_RING-5-AUTOIP_ADDRESS_POOL_EXHAUST 5-Notice Free IP addresses are not available in the Auto-IP Server pool. Configure additional pools to get IP addresses for the requesting The Auto-IP server is configured with pools of Auto-IP addresses. The IP addresses are assigned to the requesting ring ports. The Auto-IP address pool is exhaused and there are no more free addresses. auto_ip_ring "Configure additional address pools in the" " Auto-IP server by using the configuration command" " 'auto-ip-ring server' and the sub command" " 'ipv4-address-pool " AUTO_IP_RING-5-AUTOIP_HOST_ADD_SUCCESS 5-Notice IP address[inet]/31 is assigned to the ring port[chars] and IP address is assigned to the ring port and the device is added to the ring successfully auto_ip_ring "Use the 'show auto-ip-ring' or 'show run' command" " on the device to view the configured IP address on the ring port." AUTO_IP_RING-5-AUTOIP_HOST_INSERT_SUCCESS 5-Notice IP addresses[inet]/31 [inet]/31 are assigned to the ring ports[chars] [chars] IP addresses are assigned to the ring ports and the device is inserted into the ring successfully auto_ip_ring "Use the 'show auto-ip-ring' or 'show run' command" " on the device to view the configured IP addresses on the ring ports." AUTO_IP_RING-5-AUTOIP_IP_ADDR_SUCCESS_PORT 5-Notice IP address[inet] is assigned to the ring port[chars] successfully IP address is assigned to the ring port successfully. auto_ip_ring "Use the 'sh ip interface' or 'show run' command" " to view the IP address of the ring port." AUTO_IP_RING-5-DUPL_AUTOIP_ADDRESS 5-Notice Neighbor device advertised the same configured Auto-IP address[inet] Auto-IP Ring feature requires each device to configure a unique auto-ip address different from those on other devices. The local device is configured with an Auto-IP address. However the local device has also received the same Auto-IP address from a neighbor device. This may indicate that two devices are configured with the same Auto-IP address. auto_ip_ring "Use the 'show auto-ip-ring' or 'show run' command" " on both devices to view the configured Auto-IP address. If two edge" " devices show the same configured Auto-IP address then the duplicate" " configured Auto-IP address needs to be removed." AUTO_IP_RING-5-EQUAL_AUTOIP_PRIORITY 5-Notice Port[chars]: Received the same priority[dec] as the peer device Auto-IP Ring feature requires two neighbor devices to exchange different Auto-IP priority for IP auto-negotiation to happen. If they advertise the same Auto-IP priority then the IP auto-negotiation will not happen. This may indicate that the ring ports of the two devices are either wrongly wired or there is a missing seed configuration. auto_ip_ring "Use the 'show auto-ip-ring' or 'show run' command" " on both devices to view the IP addresses of the ring ports and the" " advertised/received Auto-IP priorities. If the Auto-IP priority is both 2" " or both 0 it represents a faulty wire connection that can be fixed by" " switching the two ring ports on one of the devices as necessary." " If the Auto-IP priority is both 1 there are two possibilities based on" " the mode. In pre-config mode manually configure an IP address on one" " device to start the Auto-IP negotiation. In auto-config mode if the" " Auto-IP server is reachable then configure 'auto-ip-ring seed'" " on one ring port of the device." AUTO_IP_RING-5-LLDP_NOT_ENABLE_ON_THIS_INTERFACE 5-Notice port [chars]: lldp not enabled for interface please enable lldp on Auto-ip depends on lldp to communicate with it's peer. So configure lldp before auto-ip configuration auto_ip_ring "Configure 'lldp run' in global config mode and" " check 'sh lldp neighbors'" AUTOCFG-3-LDP 3-Error ERRMSG_NOFLAGS - - - AUTOCFG-3-LDP 3-Error ERRMSG_NOFLAGS - - - AUTOQOS_ISSU-2-GET_BUFFER 2-Critical AutoQoS ISSU client failed to get buffer for message. Error: [dec] [chars] The AutoQoS ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. autoqos "show logging and show checkpoint client" AUTOQOS_ISSU-2-INIT 2-Critical AutoQoS ISSU client initialization failed to [chars]. Error: [dec] [chars] The AutoQoS ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. autoqos LOG_STD_ACTION AUTOQOS_ISSU-2-SEND_NEGO_FAILED 2-Critical AutoQoS ISSU client failed to send negotiation message. Error: [dec] [chars] The AutoQoS ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. autoqos "show logging and show checkpoint client" AUTOQOS_ISSU-2-SESSION_NEGO 2-Critical AutoQoS ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The AutoQoS ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. autoqos "show issu session and " "show issu negotiated capability " AUTOQOS_ISSU-2-SESSION_REGISTRY 2-Critical AutoQoS ISSU client failed to register session information. Error: [dec] [chars] The AutoQoS ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. autoqos "show issu capability entries and " "show issu session and " "show issu negotiated capability " AUTOQOS_ISSU-3-INVALID_SESSION 3-Error AutoQoS ISSU client does not have a valid registered session. The AutoQoS ISSU client does not have a valid registered session. autoqos "show issu capability entries and " "show issu session and " "show issu negotiated capability " AUTOQOS_ISSU-3-MSG_NOT_OK 3-Error AutoQoS ISSU client 'Message Type [dec]' is not compatible The AutoQoS ISSU client received an incompatible message from the peer device. The message cannot be processed. autoqos "show issu message group and " "show issu session and " "show issu negotiated version " AUTOQOS_ISSU-3-MSG_SIZE 3-Error AutoQoS ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The AutoQoS ISSU client failed to calculate the MTU for the specified message. The AutoQoS ISSU client is not able to send the message to the standby device. autoqos "show issu message group and " "show issu session and " "show issu negotiated version " AUTOQOS_ISSU-3-SESSION_UNREGISTRY 3-Error AutoQoS ISSU client failed to unregister session information. Error: [dec] [chars] The AutoQoS ISSU client failed to unregister session information. autoqos "show issu session and " "show issu negotiated capability " AUTOQOS_ISSU-3-TRANSFORM_FAIL 3-Error AutoQoS ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The AutoQoS ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the AutoQoS state between the active device and the standby device is not identical. autoqos "show issu session and " "show issu negotiated version " AUTORP-2-RADIXINIT 2-Critical Error initializing the Auto-RP radix tree An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-2-RADIXINIT 2-Critical Error initializing the Auto-RP radix tree An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-4-OVERLAP 4-Warning AutoRP [chars] packet group [inet] with mask [inet] removed because of multicast boundary for [inet] with mask [inet] The multicast boundary has a longer network mask than the AutoRP encoded group. - "Use postive permit clauses in the AutoRP Access " "Control List" AUTORP-4-OVERLAP 4-Warning AutoRP [chars] packet group [inet] with mask [inet] removed because of multicast boundary for [inet] with mask [inet] The multicast boundary has a longer network mask than the AutoRP encoded group. - "Use postive permit clauses in the AutoRP Access " "Control List" AUTORP-4-PAK_ERR 4-Warning AutoRP [chars] packet is received on interface [chars] with Source address=[inet] Destination address=[inet] TTL=[dec] IP length=[dec] Datagram size/UDP length=[dec] The AutoRP packet was received with wrong packet length. The packet has been dropped as it may be a malformed packet. - LOG_STD_NO_ACTION AUTORP-4-PAK_ERR 4-Warning AutoRP [chars] packet is received on interface [chars] with Source address=[inet] Destination address=[inet] TTL=[dec] IP length=[dec] Datagram size/UDP length=[dec] The AutoRP packet was received with wrong packet length. The packet has been dropped as it may be a malformed packet. - LOG_STD_NO_ACTION AUTORP-4-PRM_DEL 4-Warning Error expiring semi-static RP-mapping entry [inet]/[dec] RP:[inet] An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-4-PRM_DEL 4-Warning Error expiring semi-static RP-mapping entry [inet]/[dec] RP:[inet] An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-4-RADIXINSERT 4-Warning Error inserting a new entry into the RP-mapping radix tree An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-4-RADIXINSERT 4-Warning Error inserting a new entry into the RP-mapping radix tree An internal software error occurred. - LOG_STD_SH_TECH_ACTION AUTORP-5-CRP_REMOVED 5-Notice C-RP [inet] on interface [chars] has been removed This is performed either because PIM is disabled on the interface or \n the interface card has been removed - LOG_STD_NO_ACTION AUTORP-5-CRP_REMOVED 5-Notice C-RP [inet] on interface [chars] has been removed This is performed either because PIM is disabled on the interface or \n the interface card has been removed - LOG_STD_NO_ACTION AUTORP-5-MAPPING 5-Notice RP for [inet]/[dec] is now [inet] A new RP has been elected for the subject group prefix - LOG_STD_NO_ACTION AUTORP-5-MAPPING 5-Notice RP for [inet]/[dec] is now [inet] A new RP has been elected for the subject group prefix - LOG_STD_NO_ACTION AUTORP-6-RP_MAPPING_IDB_DEL 6-Information AutoRP RP-MAPPING IDB [chars] is deleted The configured rp-mapping idb has been deleted. - LOG_STD_NO_ACTION AUTORP-6-RP_MAPPING_IDB_DEL 6-Information AutoRP RP-MAPPING IDB [chars] is deleted The configured rp-mapping idb has been deleted. - LOG_STD_NO_ACTION AUTOSEC-3-CONFSAVE_FAIL 3-Error Applying AutoSecure config to running-conf failed with error [dec] Configuration of the AutoSecure session could not be applied to the running configuration security keyword:autosec LOG_STD_ACTION AUTOSEC-5-ENABLED 5-Notice AutoSecure is configured on the device Security configuration of the device is done using AutoSecure. none "Notification message only. No action required." AUTOTEMPLATE_HWIDB_DELETE-5-MPLS_TE_AUTOMESH 5-Notice ERRMSG_FLAG_TRACEBACK - - - AUTOTEMPLATE_HWIDB_DELETE-5-MPLS_TE_AUTOMESH 5-Notice ERRMSG_FLAG_TRACEBACK - - - AUTOUPGRADE-3-BADSIGNATURE 3-Error Embedded signature verification failed. The downloaded image is corrupted. This could be because of an invalid image name or a communication error. os "Make sure that the image name spcified refers to" " a valid IOS image and retry \"upgrade automatic\"." " If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information." AUTOUPGRADE-3-BADSIGNATURE 3-Error Embedded signature verification failed. The downloaded image is corrupted. This could be because of an invalid image name or a communication error. os "Make sure that the image name spcified refers to" " a valid IOS image and retry \"upgrade automatic\"." " If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information." AUTOUPGRADE-3-DELETEFAIL 3-Error Auto Upgrade Manager failed to delete the previous image [chars] Auto Upgrade Manager attempted to delete the previous image to make enough free space for the new image in the filesystem. However an error occurred while deleting the previous image os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-DELETEFAIL 3-Error Auto Upgrade Manager failed to delete the previous image [chars] Auto Upgrade Manager attempted to delete the previous image to make enough free space for the new image in the filesystem. However an error occurred while deleting the previous image os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-DOWNLOADFAIL 3-Error Auto Upgrade Manager is unable to download new image from [chars] Possible reasons of this failure include: 1. temporary communication problem 2. server unavailable 3. incorrect username/password 4. the image may not exist in the location 5. there is not enough space in filesystem os "Please ensure that there is enough free space in " " a filesystem and image path username password" " information are correct. Then retry the download" " using \"upgrade automatic getversion\"." " If the new image still fails to download" " please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-DOWNLOADFAIL 3-Error Auto Upgrade Manager is unable to download new image from [chars] Possible reasons of this failure include: 1. temporary communication problem 2. server unavailable 3. incorrect username/password 4. the image may not exist in the location 5. there is not enough space in filesystem os "Please ensure that there is enough free space in " " a filesystem and image path username password" " information are correct. Then retry the download" " using \"upgrade automatic getversion\"." " If the new image still fails to download" " please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-DOWNLOADHASHFAIL 3-Error Download hash verification fail The image downloaded from cisco.com is corrupted. This usually points to a communication error. os "Retry \"upgrade automatic\". If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information." AUTOUPGRADE-3-DOWNLOADHASHFAIL 3-Error Download hash verification fail The image downloaded from cisco.com is corrupted. This usually points to a communication error. os "Retry \"upgrade automatic\". If the problem" " persists please check Bug Toolkit on the" " Cisco web-site for previously filed bugs and" " upgrade code if necessary. If you do not find" " a previously-filed bug collect the outputs of" " \"show logging\" \"show version\" and" " \"show running-config\" and open a TAC case with" " the gathered information." AUTOUPGRADE-3-HTTPSENDFAIL 3-Error HTTP send failed: [chars] A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-HTTPSENDFAIL 3-Error HTTP send failed: [chars] A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-IDAEXCEPTION 3-Error Exception occurred: [chars]. Error retrieving image info from cisco.com. Auto upgrade manager could not obtain information about the new image from cisco.com. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-IDAEXCEPTION 3-Error Exception occurred: [chars]. Error retrieving image info from cisco.com. Auto upgrade manager could not obtain information about the new image from cisco.com. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-INVALIDCONFIG 3-Error Upgraded image does not recognize [dec] lines of startup configuration Either the saved startup configuration has invalid lines or the upgraded image is incompatible with the previous image os "Change/Delete the invalid lines from startup" " configuration or revert back to the previous" " image" AUTOUPGRADE-3-INVALIDCONFIG 3-Error Upgraded image does not recognize [dec] lines of startup configuration Either the saved startup configuration has invalid lines or the upgraded image is incompatible with the previous image os "Change/Delete the invalid lines from startup" " configuration or revert back to the previous" " image" AUTOUPGRADE-3-NODISKSPACE 3-Error Not enough free space in any filesystem. need [dec] bytes. Auto Upgrade Manager won't be able to download the specified image because there is not enough free space in any filesystem. os "Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually." AUTOUPGRADE-3-NODISKSPACE 3-Error Not enough free space in any filesystem. need [dec] bytes. Auto Upgrade Manager won't be able to download the specified image because there is not enough free space in any filesystem. os "Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually." AUTOUPGRADE-3-NODOWNLOADFS 3-Error Auto Upgrade Manager cannot download new image in the filesystem where current image is running Not enough free space in any filesystem for the new image os "Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually." AUTOUPGRADE-3-NODOWNLOADFS 3-Error Auto Upgrade Manager cannot download new image in the filesystem where current image is running Not enough free space in any filesystem for the new image os "Use Auto Upgrade Manager disk cleanup utility" " to cleanup a filesystem. Use \"disk-management" " confirm\" or \"disk-management auto\" options with" " \"upgrade automatic getversion\" to use the" " disk cleanup utility. Otherwise you may cleanup" " a filesystem manually." AUTOUPGRADE-3-NULLQ 3-Error NULL queue pointer A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-NULLQ 3-Error NULL queue pointer A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-NVSAVEFAIL 3-Error Failed to save in nvram Auto upgrade manager encountered a problem while attempting to save information to NVRAM. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the outputs of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-NVSAVEFAIL 3-Error Failed to save in nvram Auto upgrade manager encountered a problem while attempting to save information to NVRAM. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the outputs of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-RELOADFAILED 3-Error Failed to reload the device with the new image. Auto upgrade manager could not reload the device with the new image. A common reason is insufficient RAM space. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-RELOADFAILED 3-Error Failed to reload the device with the new image. Auto upgrade manager could not reload the device with the new image. A common reason is insufficient RAM space. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-SQUEEZEFAIL 3-Error Auto Upgrade Manager failed to squeeze the filesystem [chars] A software error has occurred os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-SQUEEZEFAIL 3-Error Auto Upgrade Manager failed to squeeze the filesystem [chars] A software error has occurred os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-STARTUPPROCFAIL 3-Error Failed to create the auto upgrade startup process. A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-3-STARTUPPROCFAIL 3-Error Failed to create the auto upgrade startup process. A software error has occurred. os "Please check Bug Toolkit on the Cisco web-site" " for previously filed bugs and upgrade code if" " necessary. If you do not find a previously-filed" " bug collect the console output as well as outputs" " of \"show version\"" " \"show logging\" and \"show running-config\" and" " open a TAC case for informaion on the supported" " images" AUTOUPGRADE-6-COMPLETE 6-Information Auto Upgrade of the device completed. From: [chars] To: [chars]. The device has been upgraded with a new IOS image by IOS Auto Upgrade Manager os "This is an informational message only." " These messages may be disabled by changing the" " logging level." AUTOUPGRADE-6-COMPLETE 6-Information Auto Upgrade of the device completed. From: [chars] To: [chars]. The device has been upgraded with a new IOS image by IOS Auto Upgrade Manager os "This is an informational message only." " These messages may be disabled by changing the" " logging level." AUTOUPGRADE-6-DELETEDPREVIOUS 6-Information Auto Upgrade Manager deleted the previous image [chars] The previous image has been deleted so that there is enough free space to download the new image. os "This is an informational message only." " These messages may be disabled by changing the" " logging level." AUTOUPGRADE-6-DELETEDPREVIOUS 6-Information Auto Upgrade Manager deleted the previous image [chars] The previous image has been deleted so that there is enough free space to download the new image. os "This is an informational message only." " These messages may be disabled by changing the" " logging level." AUTOUPGRADE-6-RELOADED 6-Information Successfully reloaded the new image: \[chars]\. The device has succesfully been reloaded with the image downloaded previously by IOS Auto Upgrade Manager. os "This is an informational message only." " These messages may be disabled by changing the" " logging level." AUTOUPGRADE-6-RELOADED 6-Information Successfully reloaded the new image: \[chars]\. The device has succesfully been reloaded with the image downloaded previously by IOS Auto Upgrade Manager. os "This is an informational message only." " These messages may be disabled by changing the" " logging level." BACKUP_INTERFACE-5-PREEMPT 5-Notice Preempting interface [chars] in backup pair [chars] [chars] preemption mode is [chars] Preempting the current forwarding interface in the backup interface pair. backup_int LOG_STD_NO_ACTION BACKUP_INTERFACE-5-VLB_NON_TRUNK 5-Notice Warning: Flexlink VLB is not allowed on non-trunk ports. Please configure [chars] to be a trunk port. Flexlink VLB detects a non-trunk port. backup_int LOG_STD_NO_ACTION BACKWALK-2-TOO_MANY_DEPENDENTS 2-Critical UEA OCE backwalk aborted - too many dependents Too many dependent objects > 200k were encountered during backwalk from an OCE chain object rsp3-layer3 "Please reduce the number of IGP routes below " "200k." BACKWALK-2-TOO_MANY_DEPENDENTS 2-Critical UEA OCE backwalk aborted - too many dependents Too many dependent objects > 200k were encountered during backwalk from an OCE chain object rsp3-layer3 "Please reduce the number of IGP routes below " "200k." BAP-4-NOSTATE 4-Warning [chars] [chars] [chars] in illegal state [dec] An internal software error occurred. - "Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version." BAP-4-NOSTATE 4-Warning [chars] [chars] [chars] in illegal state [dec] An internal software error occurred. - "Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version." BAP-4-WAVL 4-Warning Failed to initialize AVL tree BAP not started BAP will not be operational and will not be negotiated. - "Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version." BAP-4-WAVL 4-Warning Failed to initialize AVL tree BAP not started BAP will not be operational and will not be negotiated. - "Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version." BATCH_ERR-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - BATCH_ERR-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - BCM_BFD-3-BCM_BFD_CREATE_FAIL 3-Error BFD endpoint create failed for ld [dec] on asic [dec] BCM BFD endpoint create failed rsp3-bfd "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_BFD-3-BCM_BFD_CREATE_FAIL 3-Error BFD endpoint create failed for ld [dec] on asic [dec] BCM BFD endpoint create failed rsp3-bfd "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_BFD-3-BCM_BFD_DELETE_FAIL 3-Error BFD endpoint create failed for ld [dec] on asic [dec] BCM BFD endpoint delete failed rsp3-bfd "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_BFD-3-BCM_BFD_DELETE_FAIL 3-Error BFD endpoint create failed for ld [dec] on asic [dec] BCM BFD endpoint delete failed rsp3-bfd "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_INIT-3-BCM_KBP_INIT_APPL_FAIL 3-Error KBP Application INIT Failure on asic [dec] KBP appl initialation failed during the BCM init rsp3-infra "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_INIT-3-BCM_KBP_INIT_APPL_FAIL 3-Error KBP Application INIT Failure on asic [dec] KBP appl initialation failed during the BCM init dominica-infra "Please collect uea mgr pman logs from shell" BCM_INIT-3-BCM_KBP_INIT_ILKN_FAIL 3-Error KBP ILKN INIT Failure on asic [dec] KBP ilkn initialation failed during the BCM init rsp3-infra "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_INIT-3-BCM_KBP_INIT_ILKN_FAIL 3-Error KBP ILKN INIT Failure on asic [dec] KBP ilkn initialation failed during the BCM init dominica-infra "Please collect uea mgr pman logs from shell" BCM_TRAPS-2-BCM_SNOOP_CREATE_FAIL 2-Critical Snoop command create failed for cpuq [dec] BCM Snoop command create failed rsp3-traps "Please collect nile mgr and uea mgr pman logs" "from shell" BCM_TRAPS-2-BCM_SNOOP_CREATE_FAIL 2-Critical Snoop command create failed for cpuq [dec] BCM Snoop command create failed rsp3-traps "Please collect nile mgr and uea mgr pman logs" "from shell" BCM3142-3-LATE_MAP_FLUSH_INT 3-Error Mg[dec] Rcvr [dec] lch [dec]: LATE_MAP_FLUSH interrupt received from BCM3142 reg_mask_lo [hec] reg_mask_hi [hec] reg_count [dec] resend_mask_lo [hec] resend_mask_hi [hec] resend_count [dec] A receiver LATE_MAP_FLUSH interrupt was received from the BCM3142. cmts-infra "Shut and not shut the upstream" BCM3220-1-INITFAIL 1-Alert msgtxt_initfail The hardware failed to initialize correctly. - "Repair or replace the controller." BCM3220-3-BADUNIT 3-Error msgtxt_badunit An internal software error occurred. - "If either message recurs call your technical support representative\n\ for assistance." BCM3220-3-OWNERR 3-Error msgtxt_ownerror An Ethernet interface is malfunctioning or an internal software error\n\ occurred. - "Repair or replace the controller." BCM3220-3-TXERR 3-Error CM trasmission error occurred. - - "" BCM-4-COR_ECC_HIGH 4-Warning High correctable ECC error rate detected\n L2 cache data errors = [dec]\n L2 cache tag errors = [dec]\n Memory data errors = [dec]\n A high rate of soft-parity errors from the memory has been detected. Normal system operation may be affected. - "If there is a regular or sustained occurrence " "of this message reseat the memory or replace " "the memory with memory that is known to " "be operational. "LOG_STD_RECUR_ACTION BCM-4-COR_ECC_HIGH 4-Warning High correctable ECC error rate detected\n L2 cache data errors = [dec]\n L2 cache tag errors = [dec]\n Memory data errors = [dec]\n A high rate of soft-parity errors from the memory has been detected. Normal system operation may be affected. - "If there is a regular or sustained occurrence " "of this message reseat the memory or replace " "the memory with memory that is known to " "be operational. "LOG_STD_RECUR_ACTION BCM-4-ECC_L2CACHE 4-Warning Corrected ECC from L2 cache A soft-parity error from the Layer 2 cache has been detected and corrected. Normal system operation should continue. - "If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative." BCM-4-ECC_L2CACHE 4-Warning Corrected ECC from L2 cache A soft-parity error from the Layer 2 cache has been detected and corrected. Normal system operation should continue. - "If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative." BCM-4-ECC_MEMORY 4-Warning Corrected ECC from memory A soft-parity error from the memory has been detected and corrected. Normal system operation should continue. - "If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative." BCM-4-ECC_MEMORY 4-Warning Corrected ECC from memory A soft-parity error from the memory has been detected and corrected. Normal system operation should continue. - "If there is a regular or sustained occurrence of this message copy" "the error message exactly as it appears and report it to" "technical support representative." BCM5396-3- BAD_MODEL_ID 3-Error Unexpected model id: 0x%X The model ID of the part was not correct ubr10k-sw "Investigate possible error with Raven or GigE switch." BCM5396-3- MDIO_TIMEOUT 3-Error MDIO Timeout [chars] No response was received from the GigE switch MDIO interface ubr10k-sw "Investigate possible Raven MDIO interface" BCM5396-3- MODEL_ID 3-Error Failed to read model id Failed to read a register via MDIO. ubr10k-sw "Investigate possible error with Raven or GigE switch." BCM5396-3- READ_TIMEOUT 3-Error Timeout waiting for read pg [dec] addr [dec] len [dec] Failed to read a page register via MDIO. ubr10k-sw "Investigate possible error with Raven or GigE switch." BCM5396-3- WRITE_TIMEOUT 3-Error Timeout waiting for write pg [dec] addr [dec] len [dec] Failed to read a page register via MDIO. ubr10k-sw "Investigate possible error with Raven or GigE switch." BD_VIF-5-CREATE_DELETE 5-Notice Interface [chars] is [chars] BD-VIF interface create/delete events. l2-bdomain LOG_STD_NO_ACTION BD_VIF-5-CREATE_DELETE 5-Notice Interface [chars] is [chars] BD-VIF interface create/delete events. l2-bdomain LOG_STD_NO_ACTION BDI_IF-5-CREATE_DELETE 5-Notice Interface [chars] is [chars] BDI interface create/delete events. l2-bdomain LOG_STD_NO_ACTION BDI_IF-5-CREATE_DELETE 5-Notice Interface [chars] is [chars] BDI interface create/delete events. l2-bdomain LOG_STD_NO_ACTION BDOMAIN_BE_SW-3-BDI_ENCAP_NOT_SUPPORTED 3-Error BDI Encap is not supported in IOL use EFP to pop vlan tags - - - BDOMAIN_BE_SW-3-BDI_ENCAP_NOT_SUPPORTED 3-Error BDI Encap is not supported in IOL use EFP to pop vlan tags - - - BDOMAIN_BE_SW-3-L2FIB_ENTRY_GENERAL 3-Error [chars] The bridge-domain receives wrong info from L2FIB l2fib "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-3-L2FIB_ENTRY_GENERAL 3-Error [chars] The bridge-domain receives wrong info from L2FIB l2fib "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-3-L2FIB_ENTRY_INVALID 3-Error Null SW Handle from L2FIB [chars] The bridge-domain receives a null handle from L2FIB l2fib "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-3-L2FIB_ENTRY_INVALID 3-Error Null SW Handle from L2FIB [chars] The bridge-domain receives a null handle from L2FIB l2fib "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-3-PORT_MACS_NOT_ZERO 3-Error The port [chars] is being removed while MAC entries still exist The specified port is being removed before all learned MAC entries have been removed. ether-infra "If other error messages related to removing MAC " "entries have been reported then copy those down " "exactly. Contact your Cisco technical support " "representative and provide the gathered " "information." BDOMAIN_BE_SW-3-PORT_MACS_NOT_ZERO 3-Error The port [chars] is being removed while MAC entries still exist The specified port is being removed before all learned MAC entries have been removed. ether-infra "If other error messages related to removing MAC " "entries have been reported then copy those down " "exactly. Contact your Cisco technical support " "representative and provide the gathered " "information." BDOMAIN_BE_SW-3-REM_MAC_ENTRY_FAILED 3-Error Unable to remove MAC entry [enet] in bridge-domain [dec] The bridge-domain was unable to remove the learned MAC address entry from it's database. ether-infra "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-3-REM_MAC_ENTRY_FAILED 3-Error Unable to remove MAC entry [enet] in bridge-domain [dec] The bridge-domain was unable to remove the learned MAC address entry from it's database. ether-infra "If the error persists the router may need to " "be reloaded" BDOMAIN_BE_SW-4-PORT_MAX_MAC_ENTRIES 4-Warning The port [chars] has reached the maximum number of learned MAC entries [dec] The specified port has reached the maximum number of learned MAC entries. It will not learn more until some of the entries are removed. This may happen when the entries age out. If this error persists it may indicate that there are too many nodes on the specified port or that the age out timer is too long. ether-infra "MAC entries should be removed by the system as " "they age out. No action is required." BDOMAIN_BE_SW-4-PORT_MAX_MAC_ENTRIES 4-Warning The port [chars] has reached the maximum number of learned MAC entries [dec] The specified port has reached the maximum number of learned MAC entries. It will not learn more until some of the entries are removed. This may happen when the entries age out. If this error persists it may indicate that there are too many nodes on the specified port or that the age out timer is too long. ether-infra "MAC entries should be removed by the system as " "they age out. No action is required." BDOMAIN-3-MACSEC_BE_INIT_FAIL 3-Error Bridge-domain MAC Security back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-MACSEC_BE_INIT_FAIL 3-Error Bridge-domain MAC Security back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-MAT_BE_DEL_FAIL 3-Error Bridge-domain back-end subsystem failed to delete BD [dec] MAC Table entry [chars] Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-MAT_BE_DEL_FAIL 3-Error Bridge-domain back-end subsystem failed to delete BD [dec] MAC Table entry [chars] Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-MAT_BE_INIT_FAIL 3-Error Bridge-domain MAC Table back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-MAT_BE_INIT_FAIL 3-Error Bridge-domain MAC Table back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-PP_VFI_CFG_FAIL 3-Error Unable to add this neighbor to the target bridge-domain Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-PP_VFI_CFG_FAIL 3-Error Unable to add this neighbor to the target bridge-domain Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-STAMAC_BE_INIT_FAIL 3-Error Bridge-domain Static MAC back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-STAMAC_BE_INIT_FAIL 3-Error Bridge-domain Static MAC back-end subsystem did not initialize correctly Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-STAMAC_SSP_SSO_STAMAC_CFG_FAIL 3-Error Standby-SP cannot configure Static MAC to back-end subsystem after reaching SSO mode Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-3-STAMAC_SSP_SSO_STAMAC_CFG_FAIL 3-Error Standby-SP cannot configure Static MAC to back-end subsystem after reaching SSO mode Reason: [chars]. An internal software error occurred. ether-infra LOG_STD_ACTION BDOMAIN-4-MAC_LIMIT_VIOL_BD_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused configured bridge-domain limit [dec] to be exceeded. The bridge-domain specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. A service instance belonging to this bridge-domain received a frame with unknown source MAC address and if this address is learnt it would cause the bridge-domain limit to be exceeded. The address has not been learnt. ether-infra - BDOMAIN-4-MAC_LIMIT_VIOL_BD_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused configured bridge-domain limit [dec] to be exceeded. The bridge-domain specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. A service instance belonging to this bridge-domain received a frame with unknown source MAC address and if this address is learnt it would cause the bridge-domain limit to be exceeded. The address has not been learnt. ether-infra - BDOMAIN-4-MAC_LIMIT_VIOL_INST_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused configured service instance limit [dec] to be exceeded. The ethernet service instance specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. This service instance received a frame with unknown source MAC address and if this address is learnt it would cause the limit to be exceeded. The address has not been learnt. ether-infra - BDOMAIN-4-MAC_LIMIT_VIOL_INST_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused configured service instance limit [dec] to be exceeded. The ethernet service instance specified in the system message is not allowed to learn addresses beyond the limit specified in the system message. This service instance received a frame with unknown source MAC address and if this address is learnt it would cause the limit to be exceeded. The address has not been learnt. ether-infra - BDOMAIN-4-MAC_LIMIT_VIOL_SYS_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused system limit [dec] to be exceeded. It is not allowed to learn addresses beyond the system limit. A service instance received a frame with unknown source MAC address and if this address is learnt it would cause the system limit to be exceeded. The address has not been learnt. ether-infra - BDOMAIN-4-MAC_LIMIT_VIOL_SYS_LIMIT 4-Warning Attempt to learn a new MAC on [chars] caused system limit [dec] to be exceeded. It is not allowed to learn addresses beyond the system limit. A service instance received a frame with unknown source MAC address and if this address is learnt it would cause the system limit to be exceeded. The address has not been learnt. ether-infra - BEEP-3-SESSION_ERR 3-Error [chars] at [chars]:[dec] The BEEP subsystem had an error and may stop running. beep LOG_STD_ACTION BEEP-3-SESSION_ERR 3-Error [chars] at [chars]:[dec] The BEEP subsystem had an error and may stop running. beep LOG_STD_ACTION BEEP-3-SESSION_ERR 3-Error [chars] at [chars]:[dec] The BEEP subsystem had an error and may stop running. beep LOG_STD_ACTION BEEP-3-SLOG_LINE 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BEEP-3-SLOG_LINE 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BEEP-3-SLOG_LINE 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BEEP-3-SLOG_LINE_TB 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BEEP-3-SLOG_LINE_TB 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BEEP-3-SLOG_LINE_TB 3-Error [chars] [chars] This is an internal BEEP library error message. beep LOG_STD_ACTION BERT-3-BERT_ALREADY_TEST 3-Error A BERT is already running - - "" BERT-3-BERT_BAD_INTERFACE 3-Error Interface [dec] is down BERT cannot be executed on this interface - - "" BERT-3-BERT_INVPROFILE 3-Error The Profile [dec] is not Valid - - "" BERT-3-BERT_INVPROFILE_CHANGE 3-Error Profile [dec] currently under test cannot modify - - "" BERT-3-BERT_NO_CONT 3-Error Controller [dec] does not exist - - "" BERT-6-BERT_FINISH_TIMESLOTS 6-Information Finished Generation of Data for timeslots [dec] to [dec] on interface [dec] using profile [dec] - - "" BERT-6-BERT_RESULTS 6-Information [chars] - - "" BERT-6-BERT_START 6-Information Starting BERT on Interface [dec] with Profile [chars] - - "" BERT-6-BERT_TIMESLOTS 6-Information No Results will be generated for this Test - - "" BFD_CFG-3-MALLOC 3-Error Malloc failure [chars] malloc failure bfd LOG_STD_ACTION BFD_CFG-3-MALLOC 3-Error Malloc failure [chars] malloc failure bfd LOG_STD_ACTION BFD_CFG-3-MALLOC_CFG 3-Error Malloc failure [chars] [chars] malloc failure bfd LOG_STD_ACTION BFD_CFG-3-MALLOC_CFG 3-Error Malloc failure [chars] [chars] malloc failure bfd LOG_STD_ACTION BFD_CFG-3-WAVL_DELETE 3-Error Wavl delete failed for %p wavl delete failed. bfd LOG_STD_ACTION BFD_CFG-3-WAVL_DELETE 3-Error Wavl delete failed for %p wavl delete failed. bfd LOG_STD_ACTION BFD_CFG-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree wavl_init failed. bfd LOG_STD_ACTION BFD_CFG-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree wavl_init failed. bfd LOG_STD_ACTION BFD_CFG-3-WAVL_INSERT_FAIL 3-Error Wavl insert failed [chars] [chars] wavl insert failed. bfd LOG_STD_ACTION BFD_CFG-3-WAVL_INSERT_FAIL 3-Error Wavl insert failed [chars] [chars] wavl insert failed. bfd LOG_STD_ACTION BFD_DAMP-5-ZERODELAY 5-Notice Dampening reuse timer is updated with 0 delay time Inconsistency of dampening reuse timer wheel bfd LOG_STD_NO_ACTION BFD_DAMP-5-ZERODELAY 5-Notice Dampening reuse timer is updated with 0 delay time Inconsistency of dampening reuse timer wheel bfd LOG_STD_NO_ACTION BFD_HA-2-CF 2-Critical [chars][dec] CF related error bfd LOG_STD_ACTION BFD_HA-2-CF 2-Critical [chars][dec] CF related error bfd LOG_STD_ACTION BFD_HA-2-ET 2-Critical [chars][dec] Enhanced-timer error bfd LOG_STD_ACTION BFD_HA-2-ET 2-Critical [chars][dec] Enhanced-timer error c3pl LOG_STD_ACTION BFD_HA-2-RESOURCE 2-Critical [chars] System resource error occured bfd LOG_STD_ACTION BFD_HA-2-RESOURCE 2-Critical [chars] System resource error occured bfd LOG_STD_ACTION BFD_ISSU-2-GET_BUFFER 2-Critical BFD ISSU client failed to get buffer for message. Error: [dec] [chars] The BFD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show logging and show checkpoint client" BFD_ISSU-2-GET_BUFFER 2-Critical BFD ISSU client failed to get buffer for message. Error: [dec] [chars] The BFD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show logging and show checkpoint client" BFD_ISSU-2-INIT 2-Critical BFD ISSU client initialization failed to [chars]. Error: [dec] [chars] The BFD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. bfd LOG_STD_ACTION BFD_ISSU-2-INIT 2-Critical BFD ISSU client initialization failed to [chars]. Error: [dec] [chars] The BFD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. bfd LOG_STD_ACTION BFD_ISSU-2-SEND_NEGO_FAILED 2-Critical BFD ISSU client failed to send negotiation message. Error: [dec] [chars] The BFD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show logging and show checkpoint client" BFD_ISSU-2-SEND_NEGO_FAILED 2-Critical BFD ISSU client failed to send negotiation message. Error: [dec] [chars] The BFD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show logging and show checkpoint client" BFD_ISSU-2-SESSION_NEGO 2-Critical BFD ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The BFD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show issu session and " "show issu negotiated capability " BFD_ISSU-2-SESSION_NEGO 2-Critical BFD ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The BFD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. bfd "show issu session and " "show issu negotiated capability " BFD_ISSU-2-SESSION_REGISTRY 2-Critical BFD ISSU client failed to register session information. Error: [dec] [chars] The BFD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. bfd "show issu capability entries and " "show issu session and " "show issu negotiated capability " BFD_ISSU-2-SESSION_REGISTRY 2-Critical BFD ISSU client failed to register session information. Error: [dec] [chars] The BFD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. bfd "show issu capability entries and " "show issu session and " "show issu negotiated capability " BFD_ISSU-3-INVALID_SESSION 3-Error BFD ISSU client does not have a valid registered session. The BFD ISSU client does not have a valid registered session. bfd "show issu capability entries and " "show issu session and " "show issu negotiated capability " BFD_ISSU-3-INVALID_SESSION 3-Error BFD ISSU client does not have a valid registered session. The BFD ISSU client does not have a valid registered session. bfd "show issu capability entries and " "show issu session and " "show issu negotiated capability " BFD_ISSU-3-MSG_SIZE 3-Error BFD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The BFD ISSU client failed to calculate the MTU for the specified message. The BFD ISSU client is not able to send the message to the standby device. bfd "show issu message group and " "show issu session and " "show issu negotiated version " BFD_ISSU-3-MSG_SIZE 3-Error BFD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The BFD ISSU client failed to calculate the MTU for the specified message. The BFD ISSU client is not able to send the message to the standby device. bfd "show issu message group and " "show issu session and " "show issu negotiated version " BFD_ISSU-3-SESSION_UNREGISTRY 3-Error BFD ISSU client failed to unregister session information. Error: [dec] [chars] The BFD ISSU client failed to unregister session information. bfd "show issu session and " "show issu negotiated capability " BFD_ISSU-3-SESSION_UNREGISTRY 3-Error BFD ISSU client failed to unregister session information. Error: [dec] [chars] The BFD ISSU client failed to unregister session information. bfd "show issu session and " "show issu negotiated capability " BFD_ISSU-3-TRANSFORM_FAIL 3-Error bfd ISSU client [chars] transform failed for message [dec]'. Error: [dec] [chars] The BFD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the BFD state between the active device and the standby device is not identical. bfd "show issu session and " "show issu negotiated version " BFD_ISSU-3-TRANSFORM_FAIL 3-Error bfd ISSU client [chars] transform failed for message [dec]'. Error: [dec] [chars] The BFD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the BFD state between the active device and the standby device is not identical. bfd "show issu session and " "show issu negotiated version " BFD_MAP-3-MALLOC 3-Error Malloc failure [chars] malloc failure bfd LOG_STD_ACTION BFD_MAP-3-MALLOC 3-Error Malloc failure [chars] malloc failure bfd LOG_STD_ACTION BFD_MAP-3-MALLOC_MAP 3-Error Malloc failure [chars] [chars] malloc failure bfd LOG_STD_ACTION BFD_MAP-3-MALLOC_MAP 3-Error Malloc failure [chars] [chars] malloc failure bfd LOG_STD_ACTION BFD_MAP-3-WAVL_DELETE 3-Error Wavl delete failed for %p wavl delete failed. bfd LOG_STD_ACTION BFD_MAP-3-WAVL_DELETE 3-Error Wavl delete failed for %p wavl delete failed. bfd LOG_STD_ACTION BFD_MAP-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree wavl_init failed. bfd LOG_STD_ACTION BFD_MAP-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree wavl_init failed. bfd LOG_STD_ACTION BFD_MAP-3-WAVL_INSERT_FAIL 3-Error Wavl insert failed [chars] [chars] wavl insert failed. bfd LOG_STD_ACTION BFD_MAP-3-WAVL_INSERT_FAIL 3-Error Wavl insert failed [chars] [chars] wavl insert failed. bfd LOG_STD_ACTION BFD_MPLS-3-CFC_REG_FAIL 3-Error CFC registration failed rc [dec] CFC registration failed. bfd LOG_STD_ACTION BFD_MPLS-3-CFC_REG_FAIL 3-Error CFC registration failed rc [dec] CFC registration failed. bfd LOG_STD_ACTION BFD_MPLS-3-CFC_UNREG_FAIL 3-Error CFC unregistration failed rc [dec] CFC unregistration failed. bfd LOG_STD_ACTION BFD_MPLS-3-CFC_UNREG_FAIL 3-Error CFC unregistration failed rc [dec] CFC unregistration failed. bfd LOG_STD_ACTION BFD_MPLS-3-TP_LSP 3-Error Session not created for intf [chars]/lsp [dec]. In-label [dec] in use for intf [chars]/lsp [dec] BFD session mismatch. bfd LOG_STD_ACTION BFD_MPLS-3-TP_LSP 3-Error Session not created for intf [chars]/lsp [dec]. In-label [dec] in use for intf [chars]/lsp [dec] BFD session mismatch. bfd LOG_STD_ACTION BFD_OFFLOAD-3-ALLOC_FAILED 3-Error Allocation of [chars] memory failed for BFD Offload feature in QFP Allocation of memory by the QFP BFD Offload feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure asr1k-bfd LOG_STD_ACTION BFD_OFFLOAD-3-HA_BULK_SYNC_FAIL 3-Error rg [dec] There was a failure such that BFD Offload domain bulk sync did not occur cpp-ucode LOG_STD_ACTION BFD_OFFLOAD-3-HA_INVALID_STATE 3-Error state [dec] An invalid HA state was received from the HA infrastructure. cpp-ucode LOG_STD_ACTION BFD_OFFLOAD-3-INIT_FAILED 3-Error Initialization of the BFD Offload feature in QFP failed Initialization of the BFD Offload feature in the QFP failed. This indicates a software failure. asr1k-bfd LOG_STD_ACTION BFD_OFFLOAD-3-PKT_REPLICA_INIT_FAILED 3-Error Failed to register with generic packet replication for BFD Offload feature in QFP BFD Offload initialization of packet replication registration failed. asr1k-bfd LOG_STD_ACTION BFD_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical QFP BFD Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP BFD Proxy initialization detected that the IPC interface initialization failed. QFP BFD proxy will not be functional while this condition exists. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-3-BFD_MEM_EXTEND_FAILED 3-Error BFD IPC subtype: [dec] Extending memory failed. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-3-BFD_MEM_REQ_FAILED 3-Error BFD IPC subtype: [dec] Requesting more memory failed. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-3-PROXY_BAD_MSG 3-Error QFP BFD Proxy received bad length message type [dec] Cisco internal software error. QFP BFD Proxy received a corrupted message from control plane. This message will be ignored. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error QFP BFD Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. QFP BFD Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error QFP BFD Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. QFP BFD Proxy message processing detected a message sent failure. The message is lost as the result of this condition. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-4-PROXY_INVALID_MSG 4-Warning QFP BFD Proxy received invalid message type [dec] Cisco internal software error. QFP BFD Proxy received an invalid message from control plane. This message will be ignored. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_PROXY-4-PROXY_INVALID_MSG_LEN 4-Warning QFP BFD Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Cisco internal software error. QFP BFD Proxy received invalid IPC message length from control plane. This message will be ignored. asr1k-bfd keyword:bfd LOG_STD_ACTION BFD_TEST-3-BAD_ADDR_TYPE 3-Error Invalid address type [dec] invalid address type bfd LOG_STD_ACTION BFD_TEST-3-BAD_ADDR_TYPE 3-Error Invalid address type [dec] invalid address type bfd LOG_STD_ACTION BFD_TEST-3-BAD_TYPE 3-Error Invalid session type [dec] invalid session type bfd LOG_STD_ACTION BFD_TEST-3-BAD_TYPE 3-Error Invalid session type [dec] invalid session type bfd LOG_STD_ACTION BFD_TEST-3-RESOURCE 3-Error Cannot add BFD TEST as RF client. Return code [dec] RF client id failed. bfd LOG_STD_ACTION BFD_TEST-3-RESOURCE 3-Error Cannot add BFD TEST as RF client. Return code [dec] RF client id failed. bfd LOG_STD_ACTION BFD_TEST-3-RF_INIT_FAIL 3-Error Failed initializing Redundnacy Facility for BFD stub client. stub RF init failed. bfd LOG_STD_ACTION BFD_TEST-3-RF_INIT_FAIL 3-Error Failed initializing Redundnacy Facility for BFD stub client. stub RF init failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree. wavl_init failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree. wavl_init failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_IPV4 3-Error Failed inserting neighbor address %30i to wavl tree thread [dec] wavl insert failed for ipv4. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_IPV4 3-Error Failed inserting neighbor address %30i to wavl tree thread [dec] wavl insert failed for ipv4. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_IPV6 3-Error Failed inserting neighbor address %30P to wavl tree thread [dec] wavl insert failed for ipv6. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_IPV6 3-Error Failed inserting neighbor address %30P to wavl tree thread [dec] wavl insert failed for ipv6. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_PW 3-Error Failed inserting neighbor address %30i and vcid %lu to wavl tree thread [dec] wavl insert failed for pw. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_INSERT_FAIL_PW 3-Error Failed inserting neighbor address %30i and vcid %lu to wavl tree thread [dec] wavl insert failed for pw. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_TREE 3-Error Failed to malloc space for wavl tree. wavl tree malloc failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_TREE 3-Error Failed to malloc space for wavl tree. wavl tree malloc failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_WALK_FAIL 3-Error wavl_walk failed while walking wavl tree thread [dec] interface [dec] wavl walk of a thread failed. bfd LOG_STD_ACTION BFD_TEST-3-WAVL_WALK_FAIL 3-Error wavl_walk failed while walking wavl tree thread [dec] interface [dec] wavl walk of a thread failed. bfd LOG_STD_ACTION BFD-3-BUFPOOL 3-Error Creation of BFD Private Buffer Pool failed could not create private buffer pool bfd LOG_STD_ACTION BFD-3-BUFPOOL 3-Error Creation of BFD Private Buffer Pool failed could not create private buffer pool bfd LOG_STD_ACTION BFD-3-CHUNK 3-Error Chunk malloc failure - [chars] - 0x%X chunk malloc failure bfd LOG_STD_ACTION BFD-3-CHUNK 3-Error Chunk malloc failure - [chars] - 0x%X chunk malloc failure bfd LOG_STD_ACTION BFD-3-CHUNK_DESTROY 3-Error Unable to destroy [chars] [chars] chunk destroy failure bfd LOG_STD_ACTION BFD-3-CHUNK_DESTROY 3-Error Unable to destroy [chars] [chars] chunk destroy failure bfd LOG_STD_ACTION BFD-3-IF_IN_USE 3-Error Interface [chars][dec] already in use interface number is already in use bfd LOG_STD_ACTION BFD-3-IF_IN_USE 3-Error Interface [chars][dec] already in use interface number is already in use bfd LOG_STD_ACTION BFD-3-ILL_IF 3-Error Illegal interface [dec][chars] interface number is out of range for platform bfd LOG_STD_ACTION BFD-3-ILL_IF 3-Error Illegal interface [dec][chars] interface number is out of range for platform bfd LOG_STD_ACTION BFD-3-INVQELEM 3-Error Invalid queue element - [chars] invalid queue element bfd LOG_STD_ACTION BFD-3-INVQELEM 3-Error Invalid queue element - [chars] invalid queue element bfd LOG_STD_ACTION BFD-3-INVVER 3-Error Invalid version type invalid version type bfd LOG_STD_ACTION BFD-3-INVVER 3-Error Invalid version type invalid version type bfd LOG_STD_ACTION BFD-3-NO_TYPE 3-Error Neighbor address type not specified as ADDR_IP[dec] [dec] - - - BFD-3-NO_TYPE 3-Error Neighbor address type not specified as ADDR_IP[dec] [dec] - - - BFD-3-NOBOOLEAN 3-Error Failed to create watched boolean could not create watched boolean bfd LOG_STD_ACTION BFD-3-NOBOOLEAN 3-Error Failed to create watched boolean could not create watched boolean bfd LOG_STD_ACTION BFD-3-NOCLIENT 3-Error Client not found client does not exist in client list bfd LOG_STD_ACTION BFD-3-NOCLIENT 3-Error Client not found client does not exist in client list bfd LOG_STD_ACTION BFD-3-NOIOUPROC 3-Error Failed to create BFD IOU Process IOU process failed to start bfd LOG_STD_ACTION BFD-3-NOIOUPROC 3-Error Failed to create BFD IOU Process IOU process failed to start bfd LOG_STD_ACTION BFD-3-NOKADIS 3-Error Failed to start Kadis. Status [dec] kadis failed to start bfd LOG_STD_ACTION BFD-3-NOKADIS 3-Error Failed to start Kadis. Status [dec] kadis failed to start bfd LOG_STD_ACTION BFD-3-NOKADIS_TICK 3-Error Failed to get kadis timer tick to start kadis timer. kadis failed to get timer tick bfd LOG_STD_ACTION BFD-3-NOKADIS_TICK 3-Error Failed to get kadis timer tick to start kadis timer. kadis failed to get timer tick bfd LOG_STD_ACTION BFD-3-NOPPPROC 3-Error Failed to create BFD PP Process pseudo-preemptive process failed to start bfd LOG_STD_ACTION BFD-3-NOPPPROC 3-Error Failed to create BFD PP Process pseudo-preemptive process failed to start bfd LOG_STD_ACTION BFD-3-PACKET 3-Error bfd_pak_coalesce - [chars] failed could not obtain or coalesce packet buffer bfd LOG_STD_ACTION BFD-3-PACKET 3-Error bfd_pak_coalesce - [chars] failed could not obtain or coalesce packet buffer bfd LOG_STD_ACTION BFD-3-WAVL_DELETE_FAIL_IPV4 3-Error Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_IPV4 3-Error Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_IPV6 3-Error Failed deleting node for neighbor %39P to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_IPV6 3-Error Failed deleting node for neighbor %39P to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_PW 3-Error Failed deleting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_PW 3-Error Failed deleting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TE_GAL_LSP 3-Error Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TE_GAL_LSP 3-Error Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TE_SR_LSP 3-Error Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TE_SR_LSP 3-Error Failed deleting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TP_LSP 3-Error Failed deleting node for LSP [chars] [chars] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_MPLS_TP_LSP 3-Error Failed deleting node for LSP [chars] [chars] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_POCH_IPV4 3-Error Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_DELETE_FAIL_POCH_IPV4 3-Error Failed deleting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree. wavl_init failed. bfd LOG_STD_ACTION BFD-3-WAVL_INIT_FAIL 3-Error Failed initializing wavl tree. wavl_init failed. bfd LOG_STD_ACTION BFD-3-WAVL_INSERT_FAIL_IPV4 3-Error Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_IPV4 3-Error Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_IPV6 3-Error Failed inserting node for neighbor %39P to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_IPV6 3-Error Failed inserting node for neighbor %39P to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_PW 3-Error Failed inserting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_PW 3-Error Failed inserting node for neighbor [inet] : vcid [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TE_GAL_LSP 3-Error Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TE_GAL_LSP 3-Error Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TE_SR_LSP 3-Error Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TE_SR_LSP 3-Error Failed inserting node for LSP [chars] [dec] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TP_LSP 3-Error Failed inserting node for LSP [chars] [chars] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_MPLS_TP_LSP 3-Error Failed inserting node for LSP [chars] [chars] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_POCH_IPV4 3-Error Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_INSERT_FAIL_POCH_IPV4 3-Error Failed inserting node for neighbor [inet] to wavl tree thread [dec] [chars] - - - BFD-3-WAVL_TREE 3-Error Failed to malloc space for wavl tree. wavl tree malloc failed. bfd LOG_STD_ACTION BFD-3-WAVL_TREE 3-Error Failed to malloc space for wavl tree. wavl tree malloc failed. bfd LOG_STD_ACTION BFD-6-BFD_IF_CONFIGURE 6-Information BFD-SYSLOG: bfd config apply idb:[chars] bfd config change bfd LOG_STD_NO_ACTION BFD-6-BFD_IF_CONFIGURE 6-Information BFD-SYSLOG: bfd config apply idb:[chars] bfd config change bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_CREATED 6-Information BFD-SYSLOG: bfd_session_created neigh [chars] proc:[chars] idb:[chars] handle:[dec] [chars] bfd session created bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_CREATED 6-Information BFD-SYSLOG: bfd_session_created neigh [chars] proc:[chars] idb:[chars] handle:[dec] [chars] bfd session created bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_DESTROYED 6-Information BFD-SYSLOG: bfd_session_destroyed [chars] neigh proc:[chars] handle:[dec] [chars] bfd session destroyed bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_DESTROYED 6-Information BFD-SYSLOG: bfd_session_destroyed [chars] neigh proc:[chars] handle:[dec] [chars] bfd session destroyed bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_GET_LD 6-Information BFD-SYSLOG: bfd session get local discriminator [chars] neigh proc:[chars] handle:[dec] node: [chars] Get bfd session local discriminator bfd LOG_STD_NO_ACTION BFD-6-BFD_SESS_GET_LD 6-Information BFD-SYSLOG: bfd session get local discriminator [chars] neigh proc:[chars] handle:[dec] node: [chars] Get bfd session local discriminator bfd LOG_STD_NO_ACTION BFD-6-BFD_VRRPV3_SW_SESS_INVALID 6-Information BFD-SYSLOG: ABORT: BFD session for VRRPv3 client on interface: [chars] NOT supported in software handle:[dec] adjacency: [chars] node: [chars] bfd vrrpv3 sofware session offloading NOT supported bfd LOG_STD_NO_ACTION BFD-6-BFD_VRRPV3_SW_SESS_INVALID 6-Information BFD-SYSLOG: ABORT: BFD session for VRRPv3 client on interface: [chars] NOT supported in software handle:[dec] adjacency: [chars] node: [chars] bfd vrrpv3 sofware session offloading NOT supported bfd LOG_STD_NO_ACTION BFD-6-MAX_DESCR 6-Information BFD discrminators exhausted. No more sessions can be created. Max. discriminators assigned bfd LOG_STD_ACTION BFD-6-MAX_DESCR 6-Information BFD discrminators exhausted. No more sessions can be created. Max. discriminators assigned bfd LOG_STD_ACTION BFD-6-MAX_SESSION 6-Information Maximum session creation limit [dec] for [chars] sessions reached. Max. sessions created bfd LOG_STD_ACTION BFD-6-MAX_SESSION 6-Information Maximum session creation limit [dec] for [chars] sessions reached. Max. sessions created bfd LOG_STD_ACTION BFD-6-TIMER_NOT_SUPP 6-Information BFD timer value on interface [chars] is below the supported value of [dec] ms Fast timers not supported on slow interface bfd LOG_STD_ACTION BFD-6-TIMER_NOT_SUPP 6-Information BFD timer value on interface [chars] is below the supported value of [dec] ms Fast timers not supported on slow interface bfd LOG_STD_ACTION BFD-6-TIMERS_NOT_SUPPORTED 6-Information BFD timer value Tx: [dec] and Rx: [dec] are not supported for software sessions Timers not supported for software sessions bfd LOG_STD_ACTION BFD-6-TIMERS_NOT_SUPPORTED 6-Information BFD timer value Tx: [dec] and Rx: [dec] are not supported for software sessions Timers not supported for software sessions bfd LOG_STD_ACTION BFD-6-TX_ON_STANDBY 6-Information BFD transmit detected on standby BFD packet transmission on standby bfd LOG_STD_ACTION BFD-6-TX_ON_STANDBY 6-Information BFD transmit detected on standby BFD packet transmission on standby bfd LOG_STD_ACTION BFDFSM-3-INVEVENT 3-Error Invalid event_id 0x%X state machine invalid event bfd LOG_STD_ACTION BFDFSM-3-INVEVENT 3-Error Invalid event_id 0x%X state machine invalid event bfd LOG_STD_ACTION BFDFSM-3-INVSTATE 3-Error Invalid current state 0x%X state machine invalid state bfd LOG_STD_ACTION BFDFSM-3-INVSTATE 3-Error Invalid current state 0x%X state machine invalid state bfd LOG_STD_ACTION BFDFSM-3-INVTRANS 3-Error obj: [0x%08X] event_id: [0x%08X] er_p: [0x%08X] arg: [0x%08X] session state [chars] -> [chars] state machine invalid transition bfd LOG_STD_ACTION BFDFSM-3-INVTRANS 3-Error obj: [0x%08X] event_id: [0x%08X] er_p: [0x%08X] arg: [0x%08X] session state [chars] -> [chars] state machine invalid transition bfd LOG_STD_ACTION BFDFSM-3-NOEVENT 3-Error Unable to apply event 0x%08X state machine transition failure bfd LOG_STD_ACTION BFDFSM-3-NOEVENT 3-Error Unable to apply event 0x%08X state machine transition failure bfd LOG_STD_ACTION BFDFSM-3-NULLMACH 3-Error Invalid machine pointer 0x%X state machine invalid pointer bfd LOG_STD_ACTION BFDFSM-3-NULLMACH 3-Error Invalid machine pointer 0x%X state machine invalid pointer bfd LOG_STD_ACTION BFDFSM-6-BFD_SESS_DOWN 6-Information BFD-SYSLOG: BFD session [chars] is going Down Reason: [chars] bfd session down bfd LOG_STD_NO_ACTION BFDFSM-6-BFD_SESS_DOWN 6-Information BFD-SYSLOG: BFD session [chars] is going Down Reason: [chars] bfd session down bfd LOG_STD_NO_ACTION BFDFSM-6-BFD_SESS_UP 6-Information BFD-SYSLOG: BFD session [chars] is going UP bfd session Up bfd LOG_STD_NO_ACTION BFDFSM-6-BFD_SESS_UP 6-Information BFD-SYSLOG: BFD session [chars] is going UP bfd session Up bfd LOG_STD_NO_ACTION BGP_LMM-3-ASSERT 3-Error Assert failed at [chars]:[dec] An internal software error has occurred mpls-vpn LOG_STD_ACTION BGP_LMM-3-ASSERT 3-Error Assert failed at [chars]:[dec] An internal software error has occurred mpls-vpn LOG_STD_ACTION BGP_LMM-3-AUTOGEN 3-Error [chars] Neighbor: [chars] Interface: [chars] There was an error while auto-generating the mpls bgp forwarding command on an interface mpls-vpn "Manually configure the mpls bgp forwarding command" " on the interface referenced in the error message." "If the problem persists copy the message exactly as" "it appears and report it to your customer service" "representative" BGP_LMM-3-AUTOGEN 3-Error [chars] Neighbor: [chars] Interface: [chars] There was an error while auto-generating the mpls bgp forwarding command on an interface mpls-vpn "Manually configure the mpls bgp forwarding command" " on the interface referenced in the error message." "If the problem persists copy the message exactly as" "it appears and report it to your customer service" "representative" BGP_LMM-3-CFC1 3-Error [chars] [chars] Error in BGP LMM and CFC interaction mpls-vpn LOG_STD_ACTION BGP_LMM-3-CFC1 3-Error [chars] [chars] Error in BGP LMM and CFC interaction mpls-vpn LOG_STD_ACTION BGP_LMM-3-CFC2 3-Error [chars] [chars] [chars] Interaction error between BGP LMM and CFC mpls-vpn LOG_STD_ACTION BGP_LMM-3-CFC2 3-Error [chars] [chars] [chars] Interaction error between BGP LMM and CFC mpls-vpn LOG_STD_ACTION BGP_LMM-3-IPRMCONNECT 3-Error [chars] Address-family [chars] BGP LMM AF registration/de-registration with IPRM failed mpls-vpn LOG_STD_ACTION BGP_LMM-3-IPRMCONNECT 3-Error [chars] Address-family [chars] BGP LMM AF registration/de-registration with IPRM failed mpls-vpn LOG_STD_ACTION BGP_LMM-3-LSD1 3-Error [chars] [chars] Error in BGP LMM and LSD interaction mpls-vpn LOG_STD_ACTION BGP_LMM-3-LSD1 3-Error [chars] [chars] Error in BGP LMM and LSD interaction mpls-vpn LOG_STD_ACTION BGP_LMM-3-LSD2 3-Error [chars] [chars] [chars] Interaction error between BGP LMM and LSD mpls-vpn LOG_STD_ACTION BGP_LMM-3-LSD2 3-Error [chars] [chars] [chars] Interaction error between BGP LMM and LSD mpls-vpn LOG_STD_ACTION BGP_LMM-3-MEM 3-Error [chars] Error in memory management mpls-vpn LOG_STD_ACTION BGP_LMM-3-MEM 3-Error [chars] Error in memory management mpls-vpn LOG_STD_ACTION BGP_LMM-3-NBRROUTE 3-Error [chars] Neighbor: [chars] Interface: [chars] A host route to an MPLS enabled BGP neighbor was not present in the routing table the problem was corrected by installing the route mpls-vpn LOG_STD_ACTION BGP_LMM-3-NBRROUTE 3-Error [chars] Neighbor: [chars] Interface: [chars] A host route to an MPLS enabled BGP neighbor was not present in the routing table the problem was corrected by installing the route mpls-vpn LOG_STD_ACTION BGP_LMM-3-PATH 3-Error [chars] label: [dec] next hop: [dec] Invalid information in a BGP path mpls-vpn LOG_STD_ACTION BGP_LMM-3-PATH 3-Error [chars] label: [dec] next hop: [dec] Invalid information in a BGP path mpls-vpn LOG_STD_ACTION BGP_LMM-3-REENTRY 3-Error [chars] A non re-entrant routine has been re-entered mpls-vpn LOG_STD_ACTION BGP_LMM-3-REENTRY 3-Error [chars] A non re-entrant routine has been re-entered mpls-vpn LOG_STD_ACTION BGP_LMM-3-SIZEMISMATCH 3-Error Label table size [dec] mismatch checkpoint key creation failed MPLS Label Table ID size mismatch. mpls-vpn LOG_STD_ACTION BGP_LMM-3-SIZEMISMATCH 3-Error Label table size [dec] mismatch checkpoint key creation failed MPLS Label Table ID size mismatch. mpls-vpn LOG_STD_ACTION BGP_LMM-3-VRFAGGR 3-Error [chars] [dec] Error during per VRF aggregate label processing mpls-vpn LOG_STD_ACTION BGP_LMM-3-VRFAGGR 3-Error [chars] [dec] Error during per VRF aggregate label processing mpls-vpn LOG_STD_ACTION BGP_LMM-4-LABEL 4-Warning [chars] [chars] Error during allocation/freeing of a label mpls-vpn LOG_STD_ACTION BGP_LMM-4-LABEL 4-Warning [chars] [chars] Error during allocation/freeing of a label mpls-vpn LOG_STD_ACTION BGP_LMM-6-AUTOGEN1 6-Information [chars] interface: [chars] The mpls bgp forwarding command has been automatically configured on an interface - "This is an informational message no action is " "required by the operator" BGP_LMM-6-AUTOGEN1 6-Information [chars] interface: [chars] The mpls bgp forwarding command has been automatically configured on an interface - "This is an informational message no action is " "required by the operator" BGP_LMM-6-MPLS_INIT 6-Information MPLS has been [chars] for the BGP address-family [chars] MPLS has been enabled/disabled for a given BGP address-family - "This is an informational message no action is " "required by the operator" BGP_LMM-6-MPLS_INIT 6-Information MPLS has been [chars] for the BGP address-family [chars] MPLS has been enabled/disabled for a given BGP address-family - "This is an informational message no action is " "required by the operator" BGP_LMM-6-PERCE1 6-Information Per CE label global keyid wrap trigger label reallocation Per CE label global keyid wrap trigger label reallocation mpls-vpn LOG_STD_ACTION BGP_LMM-6-PERCE1 6-Information Per CE label global keyid wrap trigger label reallocation Per CE label global keyid wrap trigger label reallocation mpls-vpn LOG_STD_ACTION BGP_MPLS-3-GEN_ERROR 3-Error [chars] BGP MPLS related general runtime errors message contents will show the error mpls-vpn LOG_STD_ACTION BGP_MPLS-3-GEN_ERROR 3-Error [chars] BGP MPLS related general runtime errors message contents will show the error mpls-vpn LOG_STD_ACTION BGP_MPLS-3-IPRMCONNECT 3-Error [chars] BGP VPNv4 failed to register to IPRM component. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-IPRMCONNECT 3-Error [chars] BGP VPNv4 failed to register to IPRM component. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-IPV4_AGGR_LABEL 3-Error global aggr label: [chars] This is related to a common AGGREGATE LABEL for all aggregate prefixes in global routing table. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-IPV4_AGGR_LABEL 3-Error global aggr label: [chars] This is related to a common AGGREGATE LABEL for all aggregate prefixes in global routing table. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-LABELALLOC 3-Error [chars] An MPLS label could not be allocated for a prefix due to an internal error mpls-vpn LOG_STD_ACTION BGP_MPLS-3-LABELALLOC 3-Error [chars] An MPLS label could not be allocated for a prefix due to an internal error mpls-vpn LOG_STD_ACTION BGP_MPLS-3-LSDCONNECT 3-Error [chars] BGP VPNv4 failed to register to MPLS Forwarding component. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-LSDCONNECT 3-Error [chars] BGP VPNv4 failed to register to MPLS Forwarding component. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-NBR_ROUTE 3-Error [chars] Problems with manipulating the bgp neighbor route needed for MPLS operations mpls-vpn LOG_STD_ACTION BGP_MPLS-3-NBR_ROUTE 3-Error [chars] Problems with manipulating the bgp neighbor route needed for MPLS operations mpls-vpn LOG_STD_ACTION BGP_MPLS-3-PER_VRF_AGGR 3-Error pervrfaggr label: [chars] This is related to PER VRF AGGREGATE LABEL feature mpls-vpn LOG_STD_ACTION BGP_MPLS-3-PER_VRF_AGGR 3-Error pervrfaggr label: [chars] This is related to PER VRF AGGREGATE LABEL feature mpls-vpn LOG_STD_ACTION BGP_MPLS-3-SIZEMISMATCH 3-Error Label table size [dec] mismatch checkpt key creation failed BGP MPLS Label Table size mismatch. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-SIZEMISMATCH 3-Error Label table size [dec] mismatch checkpt key creation failed BGP MPLS Label Table size mismatch. mpls-vpn LOG_STD_ACTION BGP_MPLS-3-VPN_REWRITE 3-Error [chars] Problems with installing updating or removing a VPN rewrite entry in the MPLS forwarding table mpls-vpn LOG_STD_ACTION BGP_MPLS-3-VPN_REWRITE 3-Error [chars] Problems with installing updating or removing a VPN rewrite entry in the MPLS forwarding table mpls-vpn LOG_STD_ACTION BGP_MPLS-7-IASLABELALLOC 7-Debug Failed to create rewrite prefix [chars] result [chars] BGP MPLS VPN rewrite creation failed. mpls-vpn LOG_STD_ACTION BGP_MPLS-7-IASLABELALLOC 7-Debug Failed to create rewrite prefix [chars] result [chars] BGP MPLS VPN rewrite creation failed. mpls-vpn LOG_STD_ACTION BGP_MPLS-7-IPv4LABELALLOC 7-Debug Failed to allocate label for IPv4 prefix [inet]/[dec] BGP MPLS IPv4 label allocation failed. mpls-vpn LOG_STD_ACTION BGP_MPLS-7-IPv4LABELALLOC 7-Debug Failed to allocate label for IPv4 prefix [inet]/[dec] BGP MPLS IPv4 label allocation failed. mpls-vpn LOG_STD_ACTION BGP_SESSION-5-ADJCHANGE 5-Notice neighbor [chars] [chars][chars][chars] topology [chars] removed from session [chars] A BGP neighbor topology was removed from a session. The message\n\ describes the change for it. This message appears only if the \n\ log-neighbor-changes command is configured for\n\ the BGP process. - "This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." BGP_SESSION-5-ADJCHANGE 5-Notice neighbor [chars] [chars][chars][chars] topology [chars] removed from session [chars] A BGP neighbor topology was removed from a session. The message\n\ describes the change for it. This message appears only if the \n\ log-neighbor-changes command is configured for\n\ the BGP process. - "This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." BGP-2-INSUFMEM 2-Critical Insufficient memory for [chars] entry The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." BGP-2-INSUFMEM 2-Critical Insufficient memory for [chars] entry The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." BGP-3-ADDBLOCK 3-Error Unable to add blocked dynamic peer [chars] Not able to save the specified data due to an error - LOG_STD_ACTION BGP-3-ADDBLOCK 3-Error Unable to add blocked dynamic peer [chars] Not able to save the specified data due to an error - LOG_STD_ACTION BGP-3-ADDCID 3-Error Unable to add Cluster ID [chars]. A addition to a cluster ID structure could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ADDCID 3-Error Unable to add Cluster ID [chars]. A addition to a cluster ID structure could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ADDNETWORK 3-Error Unable to add network for [chars] to radix trie An addition to the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ADDNETWORK 3-Error Unable to add network for [chars] to radix trie An addition to the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ADDROUTE 3-Error Unable to add route for [chars] to radix trie An addition to the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ADDROUTE 3-Error Unable to add route for [chars] to radix trie An addition to the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-BADMASK 3-Error Attempt to install route for [inet] without valid mask in [chars] A route can not be installed without a valid mask. - LOG_STD_ACTION BGP-3-BADMASK 3-Error Attempt to install route for [inet] without valid mask in [chars] A route can not be installed without a valid mask. - LOG_STD_ACTION BGP-3-BADROUTEMAP 3-Error Bad parameters in the route-map [chars] applied for [chars] This means the route-map should be changed bgp "Correct the route-map" BGP-3-BADROUTEMAP 3-Error Bad parameters in the route-map [chars] applied for [chars] This means the route-map should be changed bgp "Correct the route-map" BGP-3-BGP_INCONSISTENT 3-Error [chars] Inconsistent [chars] Inconsistency in the data structures bgp "This is a rare situation and is a result of internal problem." BGP-3-BGP_INCONSISTENT 3-Error [chars] Inconsistent [chars] Inconsistency in the data structures bgp "This is a rare situation and is a result of internal problem." BGP-3-BGP_INTERNAL_ERR 3-Error [chars] BGP Internal Error bgp LOG_STD_ACTION BGP-3-BGP_INTERNAL_ERR 3-Error [chars] BGP Internal Error bgp LOG_STD_ACTION BGP-3-BGP_NO_REMOTE_READ 3-Error [chars] connection timed out - has not accepted a message from us for [dec]ms hold time [dec] messages pending transmition. BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset \n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset." BGP-3-BGP_NO_REMOTE_READ 3-Error [chars] connection timed out - has not accepted a message from us for [dec]ms hold time [dec] messages pending transmition. BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset \n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "BGP failed to send UPDATE message to the neighbor for \n\ more than the hold timer. A Hold timer expiry NOTIFICATION \n\ is being sent and the session will be reset." BGP-3-BGP_SR_POLICY_FAILURE 3-Error BGP SR policy failed [chars] - Restarting BGP may be required This is a rare situation and the system likely is running out of memory. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover." BGP-3-BGP_SR_POLICY_FAILURE 3-Error BGP SR policy failed [chars] - Restarting BGP may be required This is a rare situation and the system likely is running out of memory. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover." BGP-3-BGP_SRTE_FAILURE 3-Error BGP SRTE failed [chars] - Restarting BGP may be required This is a rare situation and the system likely is running out of memory. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover." BGP-3-BGP_SRTE_FAILURE 3-Error BGP SRTE failed [chars] - Restarting BGP may be required This is a rare situation and the system likely is running out of memory. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this messsage is\n\ after a configuration change the configuration should be reverted.\n\ BGP may need to be unconfigured and reconfigured to fully recover." BGP-3-BGP_SUBSYSTEM_INIT_FAILED 3-Error BGP subsystem initialization failed: [chars] The BGP subsystem could not be initialized properly bgp LOG_STD_ACTION BGP-3-BGP_SUBSYSTEM_INIT_FAILED 3-Error BGP subsystem initialization failed: [chars] The BGP subsystem could not be initialized properly bgp LOG_STD_ACTION BGP-3-BMP_MEMORY 3-Error BMP Memory Utilization currently at %lu exceeds threshold %lu BMP memory utilization tracked by BMP message alloc\n\ exceeds maximum memory allocation configured for BMP client - "Perform BMP deactivation on excessively churning\n\ BGP neighbors receiving large number of routes and reactivate\n\ after convergence" BGP-3-BMP_MEMORY 3-Error BMP Memory Utilization currently at %lu exceeds threshold %lu BMP memory utilization tracked by BMP message alloc\n\ exceeds maximum memory allocation configured for BMP client - "Perform BMP deactivation on excessively churning\n\ BGP neighbors receiving large number of routes and reactivate\n\ after convergence" BGP-3-DELBLOCK 3-Error Unable to remove blocked dynamic peer [chars] Not able to remove the specified data due to an error - LOG_STD_ACTION BGP-3-DELBLOCK 3-Error Unable to remove blocked dynamic peer [chars] Not able to remove the specified data due to an error - LOG_STD_ACTION BGP-3-DELCID 3-Error Unable to remove Cluster ID [chars]. A deletion of a cluster-id could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-DELCID 3-Error Unable to remove Cluster ID [chars]. A deletion of a cluster-id could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-DELNETWORK 3-Error Unable to remove network for [chars] from radix trie A deletion from the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-DELNETWORK 3-Error Unable to remove network for [chars] from radix trie A deletion from the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-DELPATH 3-Error Attempted to delete path from an empty net for [chars] A BGP path could not be deleted because of an error. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." BGP-3-DELPATH 3-Error Attempted to delete path from an empty net for [chars] A BGP path could not be deleted because of an error. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." BGP-3-DELROUTE 3-Error Unable to remove route for [chars] from radix trie A deletion from the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-DELROUTE 3-Error Unable to remove route for [chars] from radix trie A deletion from the radix trie could not be completed because\n\ of an error. - LOG_STD_ACTION BGP-3-ENHANCED_REFRESH_STALEPATH 3-Error Net [chars] from bgp neighbor [chars][chars][chars] [chars] is stale after [chars] rate-limited - - - BGP-3-ENHANCED_REFRESH_STALEPATH 3-Error Net [chars] from bgp neighbor [chars][chars][chars] [chars] is stale after [chars] rate-limited - - - BGP-3-EXTCOMMLIST_REFCOUNT_WRAPPING 3-Error Extcommlist refcount [chars] wrapping - bgp - BGP-3-EXTCOMMLIST_REFCOUNT_WRAPPING 3-Error Extcommlist refcount [chars] wrapping - bgp - BGP-3-INSUFCHUNKS 3-Error Insufficient chunk pools for [chars] requested size [dec] The static chunk pools size are not correct. bgp "Collect chunk and bgp summary. This is an internal software issue" BGP-3-INSUFCHUNKS 3-Error Insufficient chunk pools for [chars] requested size [dec] The static chunk pools size are not correct. bgp "Collect chunk and bgp summary. This is an internal software issue" BGP-3-MARTIAN_IP 3-Error [chars] Martian prefix [chars] in [chars] Invalid MPLS label found in the BGP message bgp "This indicates that there is some problem on the remote router" BGP-3-MARTIAN_IP 3-Error [chars] Martian prefix [chars] in [chars] Invalid MPLS label found in the BGP message bgp "This indicates that there is some problem on the remote router" BGP-3-MAXPFXEXCEED 3-Error Number of prefixes received from [chars][chars][chars] afi [dec]: [dec] exceeds limit [dec] - - - BGP-3-MAXPFXEXCEED 3-Error Number of prefixes received from [chars][chars][chars] afi [dec]: [dec] exceeds limit [dec] - - - BGP-3-MUTEX 3-Error Waiting for turn to execute after [dec] seconds. - - LOG_STD_ACTION BGP-3-MUTEX 3-Error Waiting for turn to execute after [dec] seconds. - - LOG_STD_ACTION BGP-3-NEGCOUNTER 3-Error Prefix-accepted counter negative for peer [chars] prefix [chars] The counter value for accepted prefixes is wrong and less than zero bgp "This is a rare situation and is a result of internal problem.\n\ Reset the session to correct it." BGP-3-NEGCOUNTER 3-Error Prefix-accepted counter negative for peer [chars] prefix [chars] The counter value for accepted prefixes is wrong and less than zero bgp "This is a rare situation and is a result of internal problem.\n\ Reset the session to correct it." BGP-3-NH_LABEL_INCONSISTENCY 3-Error Net [chars] has Nexthop-Label inconsistency Bgp peers are not consistent with each other. - "Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative." BGP-3-NH_LABEL_INCONSISTENCY 3-Error Net [chars] has Nexthop-Label inconsistency Bgp peers are not consistent with each other. - "Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative." BGP-3-NOTIFICATION 3-Error [chars] An error condition has been detected in the BGP session. A\n\ NOTIFICATION is being sent/received and the session will be reset.\n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "This message represents an error in the session and its origin \n\ should be investigated. If the error is reported periodically copy\n\ it exactly as it appears and report it to your technical support \n\ representative." BGP-3-NOTIFICATION 3-Error [chars] An error condition has been detected in the BGP session. A\n\ NOTIFICATION is being sent/received and the session will be reset.\n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "This message represents an error in the session and its origin \n\ should be investigated. If the error is reported periodically copy\n\ it exactly as it appears and report it to your technical support \n\ representative." BGP-3-NOTIFICATION_MANY 3-Error [chars] Notification sent to all the neighbors of the speaker.\n\ This message appears typically after doing 'clear ip bgp *'. bgp "If the error is unexpected report it to your technical support \n\ representative." BGP-3-NOTIFICATION_MANY 3-Error [chars] Notification sent to all the neighbors of the speaker.\n\ This message appears typically after doing 'clear ip bgp *'. bgp "If the error is unexpected report it to your technical support \n\ representative." BGP-3-ORF_EXTCOMMLIST 3-Error Received misformatted extcommunity list ORF from [chars] The received prefixlist ORF is misformatted. bgp "Check the prefixlist ORF implementation on the neighboring router." BGP-3-ORF_EXTCOMMLIST 3-Error Received misformatted extcommunity list ORF from [chars] The received prefixlist ORF is misformatted. bgp "Check the prefixlist ORF implementation on the neighboring router." BGP-3-ORF_PFXLIST 3-Error Received misformatted prefixlist ORF from [chars] - - - BGP-3-ORF_PFXLIST 3-Error Received misformatted prefixlist ORF from [chars] - - - BGP-3-RADIXINIT 3-Error Radix trie initialization failed Initialization of the radix tree could not be accomplished because of\n\ a low memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." BGP-3-RADIXINIT 3-Error Radix trie initialization failed Initialization of the radix tree could not be accomplished because of\n\ a low memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." BGP-3-REFRESH_STALEPATH_COUNT 3-Error [dec] stale-path[chars] deleted from bgp neighbor [chars][chars][chars] [chars] after [chars] BGP peers are not consistent with each other. - "BGP peers are not consistent with each other report it to your\n\ technical support representative.." BGP-3-REFRESH_STALEPATH_COUNT 3-Error [dec] stale-path[chars] deleted from bgp neighbor [chars][chars][chars] [chars] after [chars] BGP peers are not consistent with each other. - "BGP peers are not consistent with each other report it to your\n\ technical support representative.." BGP-3-RIBOUT_INCONSISTENCY 3-Error Net [chars] in [chars][chars][chars] has rib-out inconsistency for update-group [dec] [chars]- outbound policy [chars] rib-out [chars] [chars][chars] Bgp peers are not consistent with each other. - "Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative." BGP-3-RIBOUT_INCONSISTENCY 3-Error Net [chars] in [chars][chars][chars] has rib-out inconsistency for update-group [dec] [chars]- outbound policy [chars] rib-out [chars] [chars][chars] Bgp peers are not consistent with each other. - "Track the net copy the error message exactly as it appears and \n\ report it to your technical support representative." BGP-4-AFIMPORT 4-Warning [chars] prefixes imported to [chars] vrf reached the limit [dec] Number of prefixes imported from other address-family to a vrf reached configured limit bgp "Check the number of imported prefixes from the address-family and " "verify if the limit should be increased or the ip vrf import " "route-map is configured correctly." BGP-4-AFIMPORT 4-Warning [chars] prefixes imported to [chars] vrf reached the limit [dec] Number of prefixes imported from other address-family to a vrf reached configured limit bgp "Check the number of imported prefixes from the address-family and " "verify if the limit should be increased or the ip vrf import " "route-map is configured correctly." BGP-4-AO_KEYCHAIN 4-Warning [chars] You have configured BGP AO to use a keychain which BGP can not use. bgp "Correct the key chain configuration." BGP-4-AO_KEYCHAIN 4-Warning [chars] You have configured BGP AO to use a keychain which BGP can not use. bgp "Correct the key chain configuration." BGP-4-ATTRNULL 4-Warning A NULL attribute has been assigned to a path The path should have been assigned a valid attribute but was incorrectly assigned a value of NULL bgp LOG_STD_ACTION BGP-4-ATTRNULL 4-Warning A NULL attribute has been assigned to a path The path should have been assigned a valid attribute but was incorrectly assigned a value of NULL bgp LOG_STD_ACTION BGP-4-BFD_NOT_ONEHOP 4-Warning BFD is supported for single hop neighbors. [chars] is not single hop neighbor BFD is supported for single hop neighbors. The configured neighbor is not a single hop hence BFD is not enabled bgp "Deconfigure BFD from BGP as multihop " "neighbors are not supported in BFD" BGP-4-BFD_NOT_ONEHOP 4-Warning BFD is supported for single hop neighbors. [chars] is not single hop neighbor BFD is supported for single hop neighbors. The configured neighbor is not a single hop hence BFD is not enabled bgp "Deconfigure BFD from BGP as multihop " "neighbors are not supported in BFD" BGP-4-BGP_BAD_RPKI_MESSAGE 4-Warning BGP received an invalid RPKI message from rpki server [chars] [chars] [chars] hex dump: [chars] BGP is configured to connect to an RPKI server. That server is sending malformed or incorrectly formatted messages to the router bgp "Check the configuration of our RPKI server " "and make sure that the server is updated to the " "latest version " BGP-4-BGP_BAD_RPKI_MESSAGE 4-Warning BGP received an invalid RPKI message from rpki server [chars] [chars] [chars] hex dump: [chars] BGP is configured to connect to an RPKI server. That server is sending malformed or incorrectly formatted messages to the router bgp "Check the configuration of our RPKI server " "and make sure that the server is updated to the " "latest version " BGP-4-BGP_GR_RELOAD_UNSAFE_HOLDTIME 4-Warning GR reload unsafe configured holdtime[dec] the default safe You have configured an unsafe holdtime the default safe holdtime value is used instead. bgp "Configure the bgp holdtime value which is" " greater than the default safe holdtime" " value" BGP-4-BGP_GR_RELOAD_UNSAFE_HOLDTIME 4-Warning GR reload unsafe configured holdtime[dec] the default safe You have configured an unsafe holdtime the default safe holdtime value is used instead. bgp "Configure the bgp holdtime value which is" " greater than the default safe holdtime" " value" BGP-4-BGP_GR_RELOAD_UNSAFE_SESSION_RESTART_TIME 4-Warning GR reload unsafe configured session restart time[dec] You have configured an unsafe session restart time the default safe session restart time is used instead. bgp "Configure the bgp session restart time value " "which is greater than the default safe session" " restart time value" BGP-4-BGP_GR_RELOAD_UNSAFE_SESSION_RESTART_TIME 4-Warning GR reload unsafe configured session restart time[dec] You have configured an unsafe session restart time the default safe session restart time is used instead. bgp "Configure the bgp session restart time value " "which is greater than the default safe session" " restart time value" BGP-4-BGP_GR_RELOAD_UNSAFE_STALEPATH_TIME 4-Warning GR reload unsafe configured nsf stalepath time[dec] You have configured an unsafe nsf stalepath time the default safe stalepath time is used instead. bgp "Configure the bgp nsf stalepath time value " "which is greater than the default safe stalepath" "time value." BGP-4-BGP_GR_RELOAD_UNSAFE_STALEPATH_TIME 4-Warning GR reload unsafe configured nsf stalepath time[dec] You have configured an unsafe nsf stalepath time the default safe stalepath time is used instead. bgp "Configure the bgp nsf stalepath time value " "which is greater than the default safe stalepath" "time value." BGP-4-BGP_INH_POLICY 4-Warning Failed to inherit [chars] policy config '[chars]': [chars]->[chars] [chars] [chars] BGP neighbor failed to inherit some policy configuration from a policy-template or peer-group because of some configuration imcompatibilities. The set of policy configurations that were compatible were still inherited. bgp LOG_STD_ACTION BGP-4-BGP_INH_POLICY 4-Warning Failed to inherit [chars] policy config '[chars]': [chars]->[chars] [chars] [chars] BGP neighbor failed to inherit some policy configuration from a policy-template or peer-group because of some configuration imcompatibilities. The set of policy configurations that were compatible were still inherited. bgp LOG_STD_ACTION BGP-4-BGP_INH_SESSION 4-Warning Failed to inherit [chars] session config '[chars]': [chars]->[chars] [chars] BGP neighbor failed to inherit some session configuration from a session-template or peer-group because of some configuration imcompatibilities. The set of session configurations that were compatible were still inherited. bgp LOG_STD_ACTION BGP-4-BGP_INH_SESSION 4-Warning Failed to inherit [chars] session config '[chars]': [chars]->[chars] [chars] BGP neighbor failed to inherit some session configuration from a session-template or peer-group because of some configuration imcompatibilities. The set of session configurations that were compatible were still inherited. bgp LOG_STD_ACTION BGP-4-BGP_LABELS_NOT_SUPPORTED 4-Warning BGP neighbor [chars] does not support sending labels You are attempting to configure send-label either directly or via a template for a neighbor which is connected over IPv6. Doing so is not supported bgp "Do not configure send-label for IPv6 peers" BGP-4-BGP_LABELS_NOT_SUPPORTED 4-Warning BGP neighbor [chars] does not support sending labels You are attempting to configure send-label either directly or via a template for a neighbor which is connected over IPv6. Doing so is not supported bgp "Do not configure send-label for IPv6 peers" BGP-4-BGP_OUT_OF_MEMORY 4-Warning BGP resetting because of memory exhaustion. BGP tried to perform an operation that required additional memory and was not able to allocate it. bgp "Reduce other system activity to ease memory " "demands or troubleshoot the system for memory " "fragmentation. If conditions warrant upgrade " "to a larger memory configuration." BGP-4-BGP_OUT_OF_MEMORY 4-Warning BGP resetting because of memory exhaustion. BGP tried to perform an operation that required additional memory and was not able to allocate it. bgp "Reduce other system activity to ease memory " "demands or troubleshoot the system for memory " "fragmentation. If conditions warrant upgrade " "to a larger memory configuration." BGP-4-BGP_RF_REG_FAILED 4-Warning BGP failed to register with the redundancy facility. BGP failed to register with the redundancy facility. If this happens stateful switchover for BGP will not work because BGP will not be able to sync any data from the active RP to the standby RP. bgp LOG_STD_ACTION BGP-4-BGP_RF_REG_FAILED 4-Warning BGP failed to register with the redundancy facility. BGP failed to register with the redundancy facility. If this happens stateful switchover for BGP will not work because BGP will not be able to sync any data from the active RP to the standby RP. bgp LOG_STD_ACTION BGP-4-BGP_RPKI_ERROR_MESSAGE 4-Warning BGP received an RPKI Error Report PDU from rpki server [chars] [chars] [chars] hex dump [chars] The RPKI server that BGP is connected to is reporting. that the router sent it a malformed or incorrect PDU bgp "Check the configuration of the router and RPKI " "server and make sure that the server is updated " "to the latest version " BGP-4-BGP_RPKI_ERROR_MESSAGE 4-Warning BGP received an RPKI Error Report PDU from rpki server [chars] [chars] [chars] hex dump [chars] The RPKI server that BGP is connected to is reporting. that the router sent it a malformed or incorrect PDU bgp "Check the configuration of the router and RPKI " "server and make sure that the server is updated " "to the latest version " BGP-4-BGP_SESSION_PARSE 4-Warning Failed to parse [chars] neighbor config for neighbor [chars] [chars] [chars] BGP neighbor failed to parse neighbor configuration. bgp LOG_STD_ACTION BGP-4-BGP_SESSION_PARSE 4-Warning Failed to parse [chars] neighbor config for neighbor [chars] [chars] [chars] BGP neighbor failed to parse neighbor configuration. bgp LOG_STD_ACTION BGP-4-INVALIDSIZE 4-Warning invalid size for as_array has been entered - - LOG_STD_NO_ACTION BGP-4-INVALIDSIZE 4-Warning invalid size for as_array has been entered - - LOG_STD_NO_ACTION BGP-4-MAX_EXTCOMM_EXCEED 4-Warning Exceeded limit of [dec] extended communities per advertised prefix An attempt was made to advertise a prefix with an extended\n\ community attribute containing more extended communities\n\ than the allowed limit. bgp "Reduce the configured number of Route Targets or other extended\n\ communities that will be added to prefix advertisements so that\n\ the limit is not exceeded" BGP-4-MAX_EXTCOMM_EXCEED 4-Warning Exceeded limit of [dec] extended communities per advertised prefix An attempt was made to advertise a prefix with an extended\n\ community attribute containing more extended communities\n\ than the allowed limit. bgp "Reduce the configured number of Route Targets or other extended\n\ communities that will be added to prefix advertisements so that\n\ the limit is not exceeded" BGP-4-MAXDYNNBR 4-Warning BGP:DN: Cannot create new neighbor [chars] for\nrange [chars]: maximum number of [dec] dynamic neighbors limit reached Number of dynamically created subnet range neighhors reaches warning limit bgp "Check the number of listen range limit configured " "for dynamic subnet neighbors\n and verify if the " "limit should be increased." BGP-4-MAXDYNNBR 4-Warning BGP:DN: Cannot create new neighbor [chars] for\nrange [chars]: maximum number of [dec] dynamic neighbors limit reached Number of dynamically created subnet range neighhors reaches warning limit bgp "Check the number of listen range limit configured " "for dynamic subnet neighbors\n and verify if the " "limit should be increased." BGP-4-MAXPFX 4-Warning Number of prefixes received from [chars][chars][chars] afi [dec] reaches [dec] max [dec] - - - BGP-4-MAXPFX 4-Warning Number of prefixes received from [chars][chars][chars] afi [dec] reaches [dec] max [dec] - - - BGP-4-MSGDUMP 4-Warning unsupported or mal-formatted message received from [chars]: \n[chars] The remote BGP peer sent in a unsupported or mal-formatted message \n\ which caused the notification sent - LOG_STD_NO_ACTION BGP-4-MSGDUMP 4-Warning unsupported or mal-formatted message received from [chars]: \n[chars] The remote BGP peer sent in a unsupported or mal-formatted message \n\ which caused the notification sent - LOG_STD_NO_ACTION BGP-4-MULTIPATH_LOOP 4-Warning This may cause traffic loop if not used properly command accepted. Should be configured only at one of the edge routers that have ibgp \n\ peering among themselves. bgp LOG_STD_ACTION BGP-4-MULTIPATH_LOOP 4-Warning This may cause traffic loop if not used properly command accepted. Should be configured only at one of the edge routers that have ibgp \n\ peering among themselves. bgp LOG_STD_ACTION BGP-4-NBRTRACK 4-Warning Route Tracking failed on memory. Neighbor tracking for route-fall-over will stop Route tracking system failed to allocate memory. Neighbor route fall-over will stop tracking neighbor routes. bgp "Route tracking system failed to allocate memory. Neighbor " "route fall-over will stop tracking neighbor routes so that " "it can give away some memory. If you think system is stable " "then reconfigure neighbor route fall-over. If you get this " "message neighbor route-fallover has been deconfigured." BGP-4-NBRTRACK 4-Warning Route Tracking failed on memory. Neighbor tracking for route-fall-over will stop Route tracking system failed to allocate memory. Neighbor route fall-over will stop tracking neighbor routes. bgp "Route tracking system failed to allocate memory. Neighbor " "route fall-over will stop tracking neighbor routes so that " "it can give away some memory. If you think system is stable " "then reconfigure neighbor route fall-over. If you get this " "message neighbor route-fallover has been deconfigured." BGP-4-NORTRID 4-Warning BGP could not pick a router-id. Please configure manually. BGP router-id has not been manually configured and BGP is unable to allocate a router ID from the IPv4 address of one of its interfaces. bgp "Make sure that there is at least one interface that is up and has a " "valid IPv4 address or configure the router-id manually." BGP-4-NORTRID 4-Warning BGP could not pick a router-id. Please configure manually. BGP router-id has not been manually configured and BGP is unable to allocate a router ID from the IPv4 address of one of its interfaces. bgp "Make sure that there is at least one interface that is up and has a " "valid IPv4 address or configure the router-id manually." BGP-4-RIDSYNC 4-Warning BGP routes are redistributed to OSPF. For synchronization to work you must manually configure the BGP router-id to be the same as the OSPF router-id. For synchronization to work BGP router-id must be the same as the\n OSPF router-id at all times that the router is up. bgp "If synchronization is turned on between one instance of OSPF\n" "and BGP make sure to manually configure a BGP router-id which\n" "is identical to the one of that particular OSPF instance." BGP-4-RIDSYNC 4-Warning BGP routes are redistributed to OSPF. For synchronization to work you must manually configure the BGP router-id to be the same as the OSPF router-id. For synchronization to work BGP router-id must be the same as the\n OSPF router-id at all times that the router is up. bgp "If synchronization is turned on between one instance of OSPF\n" "and BGP make sure to manually configure a BGP router-id which\n" "is identical to the one of that particular OSPF instance." BGP-4-VPN_NH_IF 4-Warning Nexthop [chars] may not be reachable from neigbor [chars] - not a loopback We are sending a vpn route to this IBGP neighbor and the nexthop is one\n\ of our directly connected physical interfaces.\n\ The label for the next hop address may be removed in the MPLS cloud\n\ one hop soon. Since the P routers don't have VPN information\n\ they don't know where to forward packets with the BGP label.\n\ This could break connectivity between VPN sites. bgp "Use loopback interfaces as the nexthops for vpn IBGP neighbors." BGP-4-VPN_NH_IF 4-Warning Nexthop [chars] may not be reachable from neigbor [chars] - not a loopback We are sending a vpn route to this IBGP neighbor and the nexthop is one\n\ of our directly connected physical interfaces.\n\ The label for the next hop address may be removed in the MPLS cloud\n\ one hop soon. Since the P routers don't have VPN information\n\ they don't know where to forward packets with the BGP label.\n\ This could break connectivity between VPN sites. bgp "Use loopback interfaces as the nexthops for vpn IBGP neighbors." BGP-4-VPNV4NH_MASK 4-Warning Nexthop [inet] may not be reachable from neigbor [chars] - not /32 mask We are sending a vpnv4 route to this IBGP neighbor the nexthop\n\ address is our loopback which does not have /32 mask we are\n\ using OSPF on this loopback and the OSPF network type of this\n\ interface is LOOPBACK. OSPF advertizes this address\n\ as a host route with mask /32 regardless what mask is configured.\n\msgdef_recommended_action Configure the loopback used as the next hop with ip host mask - - BGP-4-VPNV4NH_MASK 4-Warning Nexthop [inet] may not be reachable from neigbor [chars] - not /32 mask We are sending a vpnv4 route to this IBGP neighbor the nexthop\n\ address is our loopback which does not have /32 mask we are\n\ using OSPF on this loopback and the OSPF network type of this\n\ interface is LOOPBACK. OSPF advertizes this address\n\ as a host route with mask /32 regardless what mask is configured.\n\msgdef_recommended_action Configure the loopback used as the next hop with ip host mask - - BGP-5-ADJCHANGE 5-Notice neighbor [chars][chars][chars][chars] [chars] A BGP neighbor has either come up or gone down. The message\n\ describes the change for it. This message appears only if the \n\ log-neighbor-changes command is configured for\n\ the BGP process. - "This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." BGP-5-ADJCHANGE 5-Notice neighbor [chars][chars][chars][chars] [chars] A BGP neighbor has either come up or gone down. The message\n\ describes the change for it. This message appears only if the \n\ log-neighbor-changes command is configured for\n\ the BGP process. - "This informational message normally appears as routers and\n\ BGP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." BGP-5-AGGRESSIVE_SCAN_TIME 5-Notice bgp scan-time configuration less than [dec] seconds can cause high cpu usage by BGP Scanner. bgp scan-time configuration less than 15 seconds can cause high cpu usage by BGP Scanner. - "bgp scan-time configuration less than 15 seconds can cause high cpu " "usage by BGP Scanner. It is recommended to monitor the cpu usage of " "BGP Scanner." BGP-5-AGGRESSIVE_SCAN_TIME 5-Notice bgp scan-time configuration less than [dec] seconds can cause high cpu usage by BGP Scanner. bgp scan-time configuration less than 15 seconds can cause high cpu usage by BGP Scanner. - "bgp scan-time configuration less than 15 seconds can cause high cpu " "usage by BGP Scanner. It is recommended to monitor the cpu usage of " "BGP Scanner." BGP-5-BGP_MAX_MSG_LIMIT 5-Notice BGP failed to send update message because the message size reached bgp maximum message size 4096. BGP failed to send update message because the message size reached bgp maximum message size 4096. If this happens check the bgp paths that are learned if any of the paths have got many as-paths or ext-communities - LOG_STD_ACTION BGP-5-BGP_MAX_MSG_LIMIT 5-Notice BGP failed to send update message because the message size reached bgp maximum message size 4096. BGP failed to send update message because the message size reached bgp maximum message size 4096. If this happens check the bgp paths that are learned if any of the paths have got many as-paths or ext-communities - LOG_STD_ACTION BGP-5-BGP_MAX_NSR_MSG_LIMIT 5-Notice BGP failed to send update message because the IPC to support NSR is having size less than the requested size. BGP failed to send update message because the message size is bigger than the IPC of NSR. And the neighbor may not support route refresh capability. If this happens manually hard clear the neighbor session. bgp LOG_STD_ACTION BGP-5-BGP_MAX_NSR_MSG_LIMIT 5-Notice BGP failed to send update message because the IPC to support NSR is having size less than the requested size. BGP failed to send update message because the message size is bigger than the IPC of NSR. And the neighbor may not support route refresh capability. If this happens manually hard clear the neighbor session. bgp LOG_STD_ACTION BGP-5-BGP_UPDATE_ZERO_LENGTH 5-Notice BGP failed to send update message because the message buffer size is calculated to be zero BGP failed to send update message because the message buffer size is calculated to be zero. If this happens check the bgp buffer size being calculated while sending the update for both 4byte/2byte speakers. bgp LOG_STD_ACTION BGP-5-BGP_UPDATE_ZERO_LENGTH 5-Notice BGP failed to send update message because the message buffer size is calculated to be zero BGP failed to send update message because the message buffer size is calculated to be zero. If this happens check the bgp buffer size being calculated while sending the update for both 4byte/2byte speakers. bgp LOG_STD_ACTION BGP-5-BMP_ADJCHANGE 5-Notice BMP Server [dec] - [chars]/[dec] connection [chars] A BMP server TCP connection has either come up or gone down - "This informational message normally appears as\n\ BMP servers come up or go down. If the BMP server keeps flapping\n\ its connection continuously for whatever reason flapping delay\n\ timer kicks in to regulate reconnection attempts" BGP-5-BMP_ADJCHANGE 5-Notice BMP Server [dec] - [chars]/[dec] connection [chars] A BMP server TCP connection has either come up or gone down - "This informational message normally appears as\n\ BMP servers come up or go down. If the BMP server keeps flapping\n\ its connection continuously for whatever reason flapping delay\n\ timer kicks in to regulate reconnection attempts" BGP-5-BMP_REFRESH_CAP_RCVD 5-Notice Refresh cap not received from BGP nbr session [chars] BMP monitoring not possible BMP monitoring of neighbor session is not possible in\n\ route-refresh scheme for session if refresh cap is not negotiated - "This informational message indicates BMP" " monitoring of BGP session is not possible without upgrading BGP peer" " to a software version that supports route-refresh cap" BGP-5-BMP_REFRESH_CAP_RCVD 5-Notice Refresh cap not received from BGP nbr session [chars] BMP monitoring not possible BMP monitoring of neighbor session is not possible in\n\ route-refresh scheme for session if refresh cap is not negotiated - "This informational message indicates BMP" " monitoring of BGP session is not possible without upgrading BGP peer" " to a software version that supports route-refresh cap" BGP-5-DAMPENING_DECAY_TIME 5-Notice Decay time from maximum penalty to suppress penalty is [dec] secs. Maximum penalty: [dec] suppress penalty: [dec] Configured dampening parameters may not be feasible. Time window between maximum penalty and suppress penalty may be low. bgp "If you think decay time from maximum penalty to suppress penalty " "is too low increase half-life time or maximum penalty values." BGP-5-DAMPENING_DECAY_TIME 5-Notice Decay time from maximum penalty to suppress penalty is [dec] secs. Maximum penalty: [dec] suppress penalty: [dec] Configured dampening parameters may not be feasible. Time window between maximum penalty and suppress penalty may be low. bgp "If you think decay time from maximum penalty to suppress penalty " "is too low increase half-life time or maximum penalty values." BGP-5-DAMPENING_HIGH_MAX_PENALTY 5-Notice Maximum penalty [dec] is more than allowed maximum [dec]. Configured dampening parameters may not be feasible. Maximum penalty is more than allowed maximum. Dampening will be OFF. bgp "Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is more than allowed maximum reduce " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty." BGP-5-DAMPENING_HIGH_MAX_PENALTY 5-Notice Maximum penalty [dec] is more than allowed maximum [dec]. Configured dampening parameters may not be feasible. Maximum penalty is more than allowed maximum. Dampening will be OFF. bgp "Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is more than allowed maximum reduce " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty." BGP-5-DAMPENING_LOW_MAX_PENALTY 5-Notice Maximum penalty [dec] is less than suppress penalty [dec] Configured dampening parameters may not be feasible. Maximum penalty is less than configured suppress penalty. Dampening will be OFF bgp "Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is less than suppress penalty increase " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty." BGP-5-DAMPENING_LOW_MAX_PENALTY 5-Notice Maximum penalty [dec] is less than suppress penalty [dec] Configured dampening parameters may not be feasible. Maximum penalty is less than configured suppress penalty. Dampening will be OFF bgp "Depending on the value of maximum penalty adjust maximum suppress " "time. Since maximum penalty is less than suppress penalty increase " "maximum suppress time. Maximum penalty should be greater than " "suppress penalty but less than maximum allowable penalty." BGP-5-NBR_RESET 5-Notice Neighbor [chars] reset [chars] A BGP neighbor has been marked for reset. After all of resources assigned \n\ for the neighbor are freed the adjacency will be cleared down.\n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "This message represents an error in the session was not reset \n\ because of administrative action of other valid event like an interface \n\ flap. If no valid event is detected report it to your technical support\n\ representative." BGP-5-NBR_RESET 5-Notice Neighbor [chars] reset [chars] A BGP neighbor has been marked for reset. After all of resources assigned \n\ for the neighbor are freed the adjacency will be cleared down.\n\ This message appears only if the log-neighbor-changes \n\ command is configured for the BGP process. bgp "This message represents an error in the session was not reset \n\ because of administrative action of other valid event like an interface \n\ flap. If no valid event is detected report it to your technical support\n\ representative." BGP-5-SLOWPEER_DETECT 5-Notice Neighbor [chars][chars][chars] [chars] has been detected as a slow peer. The BGP neighbor has been detected as a slow peer. - "The reason that the neighbor can not consume BGP update messages at the " "required rate should be investigated. Possible causes could be network " "congestion or high load on the peer." BGP-5-SLOWPEER_DETECT 5-Notice Neighbor [chars][chars][chars] [chars] has been detected as a slow peer. The BGP neighbor has been detected as a slow peer. - "The reason that the neighbor can not consume BGP update messages at the " "required rate should be investigated. Possible causes could be network " "congestion or high load on the peer." BGP-5-SLOWPEER_RECOVER 5-Notice Slow peer [chars][chars][chars] [chars] has recovered. The slow BGP peer has recovered. - "This message is informational. The slow-peer has recovered." BGP-5-SLOWPEER_RECOVER 5-Notice Slow peer [chars][chars][chars] [chars] has recovered. The slow BGP peer has recovered. - "This message is informational. The slow-peer has recovered." BGP-5-VERSION_WRAP 5-Notice bgp version wrapped of [chars] The BGP table version has reached its maximum value and\n\ wrapped around. The message describes this event. - "This message is informational. However frequent occurrences\n\ of such event might indicate high error rates or high packet\n\ loss in the network and should be investigated." BGP-5-VERSION_WRAP 5-Notice bgp version wrapped of [chars] The BGP table version has reached its maximum value and\n\ wrapped around. The message describes this event. - "This message is informational. However frequent occurrences\n\ of such event might indicate high error rates or high packet\n\ loss in the network and should be investigated." BGP-6-ASPATH 6-Information [chars] AS path [chars] received from [chars]: [chars] - - - BGP-6-ASPATH 6-Information [chars] AS path [chars] received from [chars]: [chars] - - - BGP-6-ATTR_DUP 6-Information BGP update error: [chars] Duplicate [chars] attribute dropped by error handling - - - BGP-6-ATTR_DUP 6-Information BGP update error: [chars] Duplicate [chars] attribute dropped by error handling - - - BGP-6-ATTR_FLAG 6-Information BGP update error: [chars] Wrong flag 0x[hec] received for [chars] attribute fixed by error handling - - - BGP-6-ATTR_FLAG 6-Information BGP update error: [chars] Wrong flag 0x[hec] received for [chars] attribute fixed by error handling - - - BGP-6-ATTR_MISSING 6-Information BGP update error: [chars] Missing mandatory attribute treat-as-withdraw by error handling - - - BGP-6-ATTR_MISSING 6-Information BGP update error: [chars] Missing mandatory attribute treat-as-withdraw by error handling - - - BGP-6-ATTR_WRONG_LEN 6-Information BGP update error: [chars] Wrong length [dec] for [chars] dropped by error handling - - - BGP-6-ATTR_WRONG_LEN 6-Information BGP update error: [chars] Wrong length [dec] for [chars] dropped by error handling - - - BGP-6-BIGCHUNK 6-Information Big chunk pool request [dec] for [chars]. Replenishing with malloc - - - BGP-6-BIGCHUNK 6-Information Big chunk pool request [dec] for [chars]. Replenishing with malloc - - - BGP-6-MALFORMED_ATTR_SET 6-Information Malformed attribute attr-set received from [chars] - - - BGP-6-MALFORMED_ATTR_SET 6-Information Malformed attribute attr-set received from [chars] - - - BGP-6-MALFORMEDATTR 6-Information Malformed attribute in [chars] - - - BGP-6-MALFORMEDATTR 6-Information Malformed attribute in [chars] - - - BGP-6-MSGDUMP_LIMIT 6-Information unsupported or mal-formatted message received from [chars]: \n[chars] - - - BGP-6-MSGDUMP_LIMIT 6-Information unsupported or mal-formatted message received from [chars]: \n[chars] - - - BGP-6-NEXTHOP 6-Information Invalid next hop [inet] received from [chars]: [chars] The remote BGP peer sent in a route with an illegal next hop.The given\n\ route was ignored. - LOG_STD_NO_ACTION BGP-6-NEXTHOP 6-Information Invalid next hop [inet] received from [chars]: [chars] The remote BGP peer sent in a route with an illegal next hop.The given\n\ route was ignored. - LOG_STD_NO_ACTION BGP-6-NOT_SUPPORTED_NEXTHOP 6-Information V6 nexthop not supported for afi/safi [dec]/[dec] The remote BGP peer sent in a route with an invalid optional transitive attribute. - "This information message appears as router detects malformed\n\ optional attributes in BGP updates. However frequent occurrences\n\ of such event should be investigated." BGP-6-NOT_SUPPORTED_NEXTHOP 6-Information V6 nexthop not supported for afi/safi [dec]/[dec] The remote BGP peer sent in a route with an invalid optional transitive attribute. - "This information message appears as router detects malformed\n\ optional attributes in BGP updates. However frequent occurrences\n\ of such event should be investigated." BGP-6-ROUTER_HOLDBACK_TIMER 6-Information BGP Router timed out waiting on dependant events BGP Router timed out waiting on dependant events and will continue with its initializations. bgp LOG_STD_NO_ACTION BGP-6-ROUTER_HOLDBACK_TIMER 6-Information BGP Router timed out waiting on dependant events BGP Router timed out waiting on dependant events and will continue with its initializations. bgp LOG_STD_NO_ACTION BIND_FAIL-2-MPLS_TE_EXT_FWDG 2-Critical ERRMSG_NOFLAGS - - - BIND_FAIL-2-MPLS_TE_EXT_FWDG 2-Critical ERRMSG_NOFLAGS - - - BINDLABEL-3-BINDLABEL_ERR 3-Error Bind label error [chars] An error happen when create/lookup bind label. BINDLABEL_COMPONENT LOG_STD_ACTION BIPC-3-SESSION_INVALID 3-Error Invalid Session Slot=[dec] Session=0x%08x An internal software error has occured. The IPC session was incorrectly not deleted when the slot went down. DDTS_COMPONENT LOG_STD_ACTION BIPC-6-SESSION_DOWN 6-Information IPCCL Session to [chars][dec] is DOWN An internal software debug info to notify IPCCL session to specific slot went down. DDTS_COMPONENT "No action is required." BIPC-6-SESSION_UP 6-Information IPCCL Session to [chars][dec] is UP An internal software debug info to notify IPCCL session to specific slot went up. DDTS_COMPONENT "No action is required." BIT-4-OUTOFRANGE 4-Warning bit [dec] is not in the expected range of [dec] to [dec] An invalid request was detected by the bitlist subsystem. cosmos LOG_STD_SH_TECH_ACTION BIT-4-OUTOFRANGE 4-Warning bit [dec] is not in the expected range of [dec] to [dec] An invalid request was detected by the bitlist subsystem. cosmos LOG_STD_SH_TECH_ACTION BOOST_PERFORMANCE-2-CONFIG_REMOVED 2-Critical Boost capability removed. Throughput will be defaulted on next reload. Reason: [chars] Device no longer support boost throughput level isr-smart-lic - BOOT_HOST_DHCP-3-ABORTING 3-Error [chars] - - - BOOT_HOST_DHCP-4-WARNING 4-Warning [chars] Configure a Device via DHCP feature has experienced an unexpected condition which did not cause a failure but suggests things did not go correctly. - LOG_STD_NO_ACTION BOOT_HOST_DHCP-6-INFO 6-Information [chars] This is an informational message generated while configuring a device via the dhcp feature. - LOG_STD_NO_ACTION BOOT-3-MODECHANGE_FAIL 3-Error [chars]. Requested by [chars] This log indicates that device-mode operation failure While device-mode change and there are errors seen and requested by specified client - LOG_STD_NO_ACTION BOOT-6-MODECHANGE 6-Information [chars] This log indicates that device-mode operation is successful While mode change and there are no errors seen - LOG_STD_NO_ACTION BP_CRIMSON-3-INITFAIL 3-Error Initialization of the IOS BP Crimson facility failed [chars]. - - - BPE-3-INVALID_IDB_TYPE 3-Error Invalid IDB type passed [[dec] - [chars]] Idb type passed is not supported by this function - LOG_STD_ACTION BPE-3-INVALID_MAC 3-Error Invalid MAC for slot [[dec]/[dec]/[dec]] Could not get proper MAC address for a given slot/subcard/port - LOG_STD_ACTION BPE-3-INVALID_PORT 3-Error Port number[[dec]] is not valid Port number is invalid - LOG_STD_ACTION BPE-3-INVALID_SLOT 3-Error Slot number[[dec]] is not valid Slot number is invalid - LOG_STD_ACTION BPE-3-MALLOC_FAILURE 3-Error Malloc Failed [[chars]] Could not allocate memory - LOG_STD_ACTION BPE-3-NOT_REGISTERED 3-Error Interface[[chars]] MAC is not registered Interface registration with BPE driver is missing - LOG_STD_ACTION BPE-3-NULL_IDB 3-Error Null idb pointer [[chars]:[hec]] Interface pointer is not initialized - LOG_STD_ACTION BRI-1-INITFAIL 1-Alert msgtxt_initfail The hardware failed to initialize correctly. - "Repair or replace the controller." BRI-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." BRI-4-NOSWITCH 4-Warning msgtxt_initfail ISDN leased line requires an ISDN switch type configure. - - BRI-4-OVERSIZE_B1_MTU 4-Warning Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec]. User config IP MTU size not supported by BRI hardware. - "Reconfigure IP MTU base on the suggested range." BRI-4-OVERSIZE_B2_MTU 4-Warning Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec]. User config IP MTU size not supported by BRI hardware. - "Reconfigure IP MTU base on the suggested range." BRI-4-OVERSIZE_D_MTU 4-Warning Failed to set MTU of [dec] on [chars]. Can't support MTU over [dec]. User config IP MTU size not supported by BRI hardware. - "Reconfigure IP MTU base on the suggested range." BRIMUX-1-BADCODE 1-Alert Software error: [chars] An internal software error occurred. as LOG_STD_ACTION BRIMUX-3-BADBRIMUX 3-Error Slot [dec] [chars] A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADDLACK 3-Error Slot [dec] BRIC failed to acknowledge download data block [dec] A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADDPM 3-Error Slot [dec] DPM test failed at offset 0x[hec] expect 0x[hec] read 0x[hec] A BRIMUX board hardware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADULADDR 3-Error Slot [dec] BRIC wrong upload address received 0x[hec] requested 0x[hec] A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADULBLK 3-Error Slot [dec] BRIC wrong block [dec] for data upload expect [dec] A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADULLEN 3-Error Slot [dec] BRIC upload data length read [dec] truncate to [dec] bytes A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-3-BADULREQ 3-Error Slot [dec] BRIC failed to send upload data block [dec] A BRIMUX firmware problem may be present. as LOG_STD_ACTION BRIMUX-4-HEARTBEAT 4-Warning Slot [dec] BRIC lost heartbeat for [dec] seconds A BRIMUX board hardware or firmware problem may be present. as LOG_STD_RECUR_ACTION BRIMUX-5-CHANUPDOWN 5-Notice B[dec] of BRI[dec] on slot [dec] BRIC changed state to [chars] A B-channel on the BRIMUX board changed state. as LOG_STD_NO_ACTION BRIMUX-5-PORTUPDOWN 5-Notice BRI[dec] on slot [dec] BRIC changed state to [chars] A port on the BRIMUX board changed state. as LOG_STD_NO_ACTION BRIMUX-5-UPDOWN 5-Notice Slot [dec] BRIC changed state to [chars] A BRIMUX board changed state. as LOG_STD_NO_ACTION BSC-2-NOMEM 2-Critical No buffers available on interface [chars]. This message indicates that memory in the router was exhausted. - "Perform diagnostics on the router to locate the subsystem or interface\n\ responsible for consuming memory. The only method that will clear this\n\ situation is to reload the router." BSC-3-BADLINESTATE 3-Error Line state Tx when receiving [chars] on line [chars] An unexpected receive occurred during a transmission. - "Verify that the line has been consistently defined in regards to the\n\ carrier. If a message report was sent hard-on stop and start the\n\ bisynchronous interface in question." BSC-3-BADPEERTYPE 3-Error Peer [chars] is incorrect type This message occurs only when BSC local-ack is configured. It\n\ indicates the serial interfaces that are using the BSTUN tunnel are\n\ configured incorrectly that is both have been configured as a\n\ secondary. - "Reconfigure the serial interfaces correctly to be a primary and\n\ secondary pair." BSR-4-CRP_NOT_CONFIGURED 4-Warning Bootstrap message received from [inet] on [chars] SDWAN running SPT-only mode but Candidate-RP not configured locally. In SDWAN spt-only networks it is expected that the cEdge is the candidate RP and elected RP if PIM BSR is running. - LOG_STD_ACTION BSR-4-CRP_NOT_CONFIGURED 4-Warning Bootstrap message received from [inet] on [chars] SDWAN running SPT-only mode but Candidate-RP not configured locally. In SDWAN spt-only networks it is expected that the cEdge is the candidate RP and elected RP if PIM BSR is running. - LOG_STD_ACTION BSR-5-CBSR_REMOVED 5-Notice Candidate-BSR on interface [chars] has been removed This is performed because the interface card has been removed - LOG_STD_NO_ACTION BSR-5-CBSR_REMOVED 5-Notice Candidate-BSR on interface [chars] has been removed This is performed because the interface card has been removed - LOG_STD_NO_ACTION BSR-5-CRP_REMOVED 5-Notice Candidate-RP on interface [chars] has been removed This is performed because the interface card has been removed - LOG_STD_NO_ACTION BSR-5-CRP_REMOVED 5-Notice Candidate-RP on interface [chars] has been removed This is performed because the interface card has been removed - LOG_STD_NO_ACTION BSR-6-NO_FORWARD_BSR 6-Information Dropping No-Forward Bootstrap message from [chars] on [chars] This is performed because RFC 5059 No-Forward BSM is not supported. - LOG_STD_NO_ACTION BSR-6-NO_FORWARD_BSR 6-Information Dropping No-Forward Bootstrap message from [chars] on [chars] This is performed because RFC 5059 No-Forward BSM is not supported. - LOG_STD_NO_ACTION BSTUN-2-NOBUF 2-Critical Interface [chars] no buffer available to [chars] A memory shortage existed at the time that the configuration command\n\ was issued. This condition is rare and under normal conditions\n\ temporary. - "Reconfigure the BSTUN group. If memory shortages persist call your\n\ technical support representative for assistance." BSTUN-3-BADCONN 3-Error CONN: bad connection [dec] peer: [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-BADLENOP 3-Error [chars]: bad len or unknown op op [dec] len [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-BADMAGIC 3-Error [chars]: wrong magic mine [hec] theirs [hec] [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-BADMAGICTCP 3-Error [chars]: peer [chars] wrong magic mine [hec] theirs [hec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-BADPASSIVEOPEN 3-Error passive open from [inet][dec] -> [dec] failed An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-CONNILLSTATE 3-Error CONN: Peer [chars] illegal state [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-IFNOTSETUP 3-Error Could not setup interface for protocol [chars] BSTUN was unable to start the interface for handling the specified protocol traffic. - "If this message appears while you are configuring BSTUN check for\n\ other system errors such as no available memory in the router or the interface\n\ shutting down. If no obvious problem can be detected record all the displayed\n\ values and any other BSTUN error messages and contact your technical support\n\ representative." BSTUN-3-NOGRPDEF 3-Error No bstun group defined on interface [chars] An action was taken that requires the previous definition of a BSTUN\n\ group number. - "Make sure "encapsulation bstun" and the "bstun group" have been\n\ defined for the interface." BSTUN-3-NOPEER 3-Error No peer configured to route frame with destination address [chars] bstun group [dec] A BSTUN route has not been configured for the frame with a destination address. - "If this message appears while you are debugging bstun it indicates that no\n\ specific bstun route has been configured for the frames being received with\n\ the device address listed in the packet debug trace. You may choose to configure\n\ a bstun route or ignore this message." BSTUN-3-SENDPUNT 3-Error [chars]: sent [chars] to [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-3-UNKPROTOEV 3-Error Unknown protocol event [dec] on interface [chars] An event passed to the BSTUN layer for processing could not\n\ be decoded. - "Perform a hard restart on the indicated interface." BSTUN-4-DUPROUTE 4-Warning Cannot define duplicate route on the\n\same group This route command is defined on another interface belonging to the\n\same group. Cannot define duplicate route on the same group - "Consider defining a new group and moving this interface onto that\n\group" BSTUN-4-PEERSTATE 4-Warning Peer [chars] wrong state [dec] [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-4-SENDPUNTTCP 4-Warning [chars]: sent [chars] to [[dec]][inet] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-6-CONNOPENFAIL 6-Information CONN: peer [chars] open failed [chars] [[dec]] An attempt to connect to a remote TCP BSTUN peer failed. - "Verify that the remote peer is accessible from this router that it is\n\ running software capable of supporting BSTUN and that it is configured\n\ correctly." BSTUN-6-ERR 6-Information [chars]: [chars]: [chars] op [hec] len [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION BSTUN-6-OPENED 6-Information [chars]: peer [chars] opened [previous state [chars]] - - LOG_STD_NO_ACTION BSTUN-6-OPENING 6-Information CONN: opening peer [chars] [dec] - - LOG_STD_NO_ACTION BSTUN-6-PASSIVEOPEN 6-Information passive open [inet][dec] -> [dec] - - LOG_STD_NO_ACTION BSTUN-6-PEERSHUTDOWN 6-Information shutting down peer [chars] on [chars] A connection to a remote peer is being shut down. This is typically\n\ the result of user intervention in BSTUN reconfiguration or disabling.\n\ This is good expected behavior. - LOG_STD_NO_ACTION BSTUN-6-PROCEXIT 6-Information Process terminating. Due to signal [dec]. Subcode [dec]. Address [hec]. The BSTUN background process is terminating. - "If this message appears while you are unconfiguring BSTUN no action\n\ is required. Otherwise record all the displayed values and any other\n\ BSTUN error messages and contact your technical support\n\ representative." BSTUN-6-RECONNECT 6-Information PHDR: reconnect from peer [chars] A remote peer reestablished a connection to this router. - LOG_STD_NO_ACTION BSTUN-6-TCPFINI 6-Information peer [chars] closed [previous state [chars]] A remote peer closed a BSTUN connection with this router. - "Examine the other router to see why it closed this connection with\n\ this peer. This can be caused by normal events such as\n\ reconfiguration." BSTUN-6-TCPPEERSHUT 6-Information [chars] [chars] [inet][dec] This route closed a BSTUN connection with a remote peer. - "Examine this router to see why it closed this connection with this\n\ peer. This can be caused by normal events such as reconfiguration." BUFCAP-3-ACTIVE_CAPPOINT 3-Error Invalid operation was attempted on an active capture point [chars]. Invalid operation was attempted on an active \n\ capture point. os "Search for resolved software issues using the Bug Toolkit " "at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance copy the error message exactly as " "it appears on the console or in the system log enter the " "show monitor capture point all and " "show tech commands and contact your " "Cisco technical support representative providing the " "representative with the gathered information." BUFCAP-3-ACTIVE_CAPPOINT 3-Error Invalid operation was attempted on an active capture point [chars]. Invalid operation was attempted on an active \n\ capture point. os "Search for resolved software issues using the Bug Toolkit " "at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance copy the error message exactly as " "it appears on the console or in the system log enter the " "show monitor capture point all and " "show tech commands and contact your " "Cisco technical support representative providing the " "representative with the gathered information." BUFCAP-3-EXPORT_BUFFER 3-Error Error exporting buffer [chars] to location [chars] The Buffer Capture Infrastructure is not able to export the buffer to the specified location os "Please check if a valid destination was specified. " "Or if a file by the same name already exists rename the dump file or " "remove the existing file from the destination location. " "If those actions do not resolve the problem " LOG_STD_ACTION BUFCAP-3-EXPORT_BUFFER 3-Error Error exporting buffer [chars] to location [chars] The Buffer Capture Infrastructure is not able to export the buffer to the specified location os "Please check if a valid destination was specified. " "Or if a file by the same name already exists rename the dump file or " "remove the existing file from the destination location. " "If those actions do not resolve the problem " LOG_STD_ACTION BUFCAP-3-INVALID_CAPPOINT 3-Error Invalid capture point. Some operation was attempted on a invalid capture point. os LOG_STD_ACTION BUFCAP-3-INVALID_CAPPOINT 3-Error Invalid capture point. Some operation was attempted on a invalid capture point. os LOG_STD_ACTION BUFCAP-3-INVALID_PARAM 3-Error Invalid parameters Invalid parameters were passed in to a buffer capture infrastructure function. os LOG_STD_ACTION BUFCAP-3-INVALID_PARAM 3-Error Invalid parameters Invalid parameters were passed in to a buffer capture infrastructure function. os LOG_STD_ACTION BUFCAP-3-NO_MEM 3-Error Not enough memory available for Buffer Capture Infrastructure The buffer capture infrastructure could not get the memory it requested. os LOG_STD_REDUCE_ACTION BUFCAP-3-NO_MEM 3-Error Not enough memory available for Buffer Capture Infrastructure The buffer capture infrastructure could not get the memory it requested. os LOG_STD_REDUCE_ACTION BUFCAP-3-NOSUCHCAPTURE 3-Error Error finding capture point. No such capture point exists os LOG_STD_ACTION BUFCAP-3-NOSUCHCAPTURE 3-Error Error finding capture point. No such capture point exists os LOG_STD_ACTION BUFCAP-5-BUFFER_FULL 5-Notice Linear Buffer associated with capture buffer [chars] is full. The linear buffer is full. Further capture would be halted. os LOG_STD_NO_ACTION BUFCAP-5-BUFFER_FULL 5-Notice Linear Buffer associated with capture buffer [chars] is full. The linear buffer is full. Further capture would be halted. os LOG_STD_NO_ACTION BUFCAP-5-MAX_ELEMS 5-Notice Capture point [chars] disabled. The number of elements in associated capture buffer's [chars] The buffer contains the maximum configured number of packets. The associated capture point will be disabled. os LOG_STD_NO_ACTION BUFCAP-5-MAX_ELEMS 5-Notice Capture point [chars] disabled. The number of elements in associated capture buffer's [chars] The buffer contains the maximum configured number of packets. The associated capture point will be disabled. os LOG_STD_NO_ACTION BUFCAP-5-TIME_EXCEEDED 5-Notice Capture Point [chars] disabled. The associated capture buffer's [chars] The linear buffer does not have enough space left. Hence the packet was trimmed. This is the final element in the buffer. os LOG_STD_NO_ACTION BUFCAP-5-TIME_EXCEEDED 5-Notice Capture Point [chars] disabled. The associated capture buffer's [chars] The linear buffer does not have enough space left. Hence the packet was trimmed. This is the final element in the buffer. os LOG_STD_NO_ACTION BUFCAP-6-CAPPOINT_EXISTS 6-Information Capture Point [chars] already exists. A Capture point by the specified name already exists. os LOG_STD_NO_ACTION BUFCAP-6-CAPPOINT_EXISTS 6-Information Capture Point [chars] already exists. A Capture point by the specified name already exists. os LOG_STD_NO_ACTION BUFCAP-6-CREATE 6-Information Capture Point [chars] created. Specified capture point has been created. os LOG_STD_NO_ACTION BUFCAP-6-CREATE 6-Information Capture Point [chars] created. Specified capture point has been created. os LOG_STD_NO_ACTION BUFCAP-6-DELETE 6-Information Capture Point [chars] deleted. Specified capture point has been deleted. os LOG_STD_NO_ACTION BUFCAP-6-DELETE 6-Information Capture Point [chars] deleted. Specified capture point has been deleted. os LOG_STD_NO_ACTION BUFCAP-6-DISABLE 6-Information Capture Point [chars] disabled. Specified capture point has been disabled. os LOG_STD_NO_ACTION BUFCAP-6-DISABLE 6-Information Capture Point [chars] disabled. Specified capture point has been disabled. os LOG_STD_NO_ACTION BUFCAP-6-DISABLE_ASYNC 6-Information Capture Point [chars] disabled. Reason : [chars] Specified capture point has been disabled due to asynchronous event. os LOG_STD_NO_ACTION BUFCAP-6-DISABLE_ASYNC 6-Information Capture Point [chars] disabled. Reason : [chars] Specified capture point has been disabled due to asynchronous event. os LOG_STD_NO_ACTION BUFCAP-6-ENABLE 6-Information Capture Point [chars] enabled. Specified capture point has been enabled. os LOG_STD_NO_ACTION BUFCAP-6-ENABLE 6-Information Capture Point [chars] enabled. Specified capture point has been enabled. os LOG_STD_NO_ACTION BUFCAP-6-RATE_LIMIT 6-Information [dec] packets from capture point [chars] dropped due to rate limiting. Rate limiting has been enabled and the number of packets exceed the allowed configured value. os - BUFCAP-6-RATE_LIMIT 6-Information [dec] packets from capture point [chars] dropped due to rate limiting. Rate limiting has been enabled and the number of packets exceed the allowed configured value. os - BUFCAP-6-TOO_BIG 6-Information The packet to be dumped is bigger than the buffer size of capture buffer [chars]. Packet of size [dec] dropped. The packet is bigger than the configured/default buffer size. os "Change the parameters of the capture buffer. " "You can try to increase the size of the buffer " "or limit the number of bytes copied." BUFCAP-6-TOO_BIG 6-Information The packet to be dumped is bigger than the buffer size of capture buffer [chars]. Packet of size [dec] dropped. The packet is bigger than the configured/default buffer size. os "Change the parameters of the capture buffer. " "You can try to increase the size of the buffer " "or limit the number of bytes copied." BUNDLE_INSERT-2-MPLS_TE 2-Critical ERRMSG_FLAG_TRACEBACK - - - BUNDLE_INSERT-2-MPLS_TE 2-Critical ERRMSG_FLAG_TRACEBACK - - - BUNDLES-3-ALLOCATION 3-Error Bundle allocation error: [chars] An internal software error occurred. It is likely that this error is caused by a low memory condition OCE_DDTS_COMPONENT LOG_STD_ACTION BUNDLES-3-ALLOCATION 3-Error Bundle allocation error: [chars] An internal software error occurred. It is likely that this error is caused by a low memory condition OCE_DDTS_COMPONENT LOG_STD_ACTION BUNDLES-3-PLATFORMSPACE 3-Error Platform attempted to access unreserved space An internal software error occurred. OCE_DDTS_COMPONENT LOG_STD_ACTION BUNDLES-3-PLATFORMSPACE 3-Error Platform attempted to access unreserved space An internal software error occurred. OCE_DDTS_COMPONENT LOG_STD_ACTION BUNDLES-3-TYPENOTISSUAWARE 3-Error Bundle type [chars] must be ISSU aware to send to slots [chars] - - - BUNDLES-3-TYPENOTISSUAWARE 3-Error Bundle type [chars] must be ISSU aware to send to slots [chars] - - - BW_LICENSE-4-THROUGHPUT_MAX_LEVEL 4-Warning Average throughput rate approached the licensed bandwidth of [chars] during [dec] sampling periods in the last 24 hours sampling period is [dec] seconds - - - BW_LICENSE-5-THROUGHPUT_THRESHOLD_LEVEL 5-Notice Average throughput rate exceeded [dec] percent of licensed bandwidth of [chars] during [dec] sampling periods in the last 24 hours sampling period is [dec] seconds - - - C2950_MONITOR-3-C2950MONITOR_UNKNOWN_PARAM 3-Error Unknown trap type:[dec] received in emt_call function. Unknow trap type. Some feature requires this trap type to be handled - - C3PL_TARGET-4- NOREG 4-Warning No [chars] callback registered for [chars]. Using default function. A support function for a specific kind of QoS attachment point is not available. A default behavior was applied instead. C3PL_TARGET_DDTS_COMPONENT - C3PL_TARGET-4- NOREG 4-Warning No [chars] callback registered for [chars]. Using default function. A support function for a specific kind of QoS attachment point is not available. A default behavior was applied instead. C3PL_TARGET_DDTS_COMPONENT - C4K_IOSINTF-4-INTVLANALLOCFAIL 4-Warning Failed to allocate internal VLAN for interface [chars]. The interface will remain down. When a routed port or port channel interface is enabled it must allocate an internal VLAN in order to operate. If there are no internal VLANs available when an interface is enabled the interface remains down and this message is logged. - "An internal VLAN can be freed up by disabling some other routed port " "or port channel interface or by deleting a user configured VLAN in " "the 1006 to 4094 range. Once a VLAN is made available the interface " "will come up if it is disabled and re-enabled." C4K_IOSINTF-4-REFLEXIVEACLNOTSUPPORTED 4-Warning Reflexive Acls are not supported. Ignoring the [chars] entry. Reflexive Acls are not supported. Aces with Evaluate and Reflect keywords are ignored. - "Do not configure Aces with Evaluate or Reflect keyword. " C4K_IOSINTF-5-NOTXVLAN 5-Notice Router Port [chars] has no internal vlan assigned to transmit packet The L3 Interface specified does not have an internal vlan assigned. - - C4K_IOSINTF-5-STALEPHYPORT 5-Notice Dropping packets to be transmitted out on port [chars] Linecard in Slot [dec] may have been removed During hot-swapping operations sometimes a prevously queued packet may be transmitted after a delay by which time the linecard does not exist anymore. This indicates such packets are being dropped - "This occurs when there are queued packets that are transmitted by which " "time the linecard in that slot has been removed already. If the problem " "persists even without any hotswapping operations please contact your " "Cisco Technical Support representative " C4K_IOSINTF-5-TXL3PKTONPHYPORT 5-Notice Transmitting L3 packet on a physical port [chars] that is part of [chars] [dec] packets. Make sure the physical port in the L3 port The L3 protocols operate at the logical port level and not on physical port level. This message indicates an situation that causes L3 protocol packets to be sent on a physical port that is part of a bundle. This can happen if there is a misconfiguration. Maybe there is an ip address assigned to a physical port that is part of a layer 3 port channel - LOG_STD_ACTION C4K_IOSINTF-5-TXPKTDROPONETHERCHANNEL 5-Notice Dropping transmit packet out of interface [chars] A packet to be transmitted out of a Port-Channel is being dropped during transitions in the Port-Channel membership - "This occurs when a packet is being transmitted out of the aggregate " "port by higher layer protocols but the software cannot find specific " "state information. This can temporarily happen when physical ports " "transition into or out of the channel. If the problem persists please " "contact your Cisco Technical Support representative" C4K_IOSSYS-7-INVALIDVALUE 7-Debug [chars] Type [dec] not handled returning a default of 0 This message is for debugging purposes. When you see this message report it to your technical support representative. cat4000 LOG_STD_ACTION C4K_REDUNDANCY-2- IOS_VERSION_CHECK_FAIL 2-Critical [chars] For proper operation of redundancy the system must be configured with symmetrical hardware and software. Here we have detected an IOS version mismatch between the Active and Standby. In this condition redundancy operations are not guaranteed. - "Configure the system so that the Active and Standby supervisors are running the same version of IOS." C4K_REDUNDANCY-2- NON_SYMMETRICAL_REDUNDANT_SYSTEM 2-Critical [chars] For proper operation of redundancy the system must be configured with symmetrical hardware. Here we have detected mismatch between the Active and Standby hardware. In this condition redundancy operations are not guaranteed. - "Configure the hardware so that the Active and Standby supervisors are identical in all respects." C4K_REDUNDANCY-2- POSTFAIL 2-Critical POST failure on [chars] supervisor detected Active supervisor failed POST. Standby supervisor will reset current active and attempt to become active. - "Please run offline diagnostics on the failed supervisor to isolate the failure" C4K_REDUNDANCY-4- CONFIGSYNCFAIL 4-Warning Persistent-config Sync to Standby supervisor failed. Active supervisor failed to receive PLATFORM_SYNC_DONE message from Standby. Potential problem with Standby. - "" C4K_REDUNDANCY-5- CONFIGSYNC 5-Notice The [chars] has been successfully synchronized to the standby supervisor The configuration has been successfully synchronized to the standby supervisor - "This is an informational message. No action is required." C4K_REDUNDANCY-5- CONFIGSYNC_RATELIMIT 5-Notice The [chars] has been successfully synchronized to the standby supervisor The configuration has been successfully synchronized to the standby supervisor This is a rate limited message. These messages are logged at 1 min interval when lots of messages are generated continuously - "This is an informational message. No action is required." C4K_REDUNDANCY-6- ACTIVESUPNOTFOUND 6-Information Active supervisor not found. Informational message on standby supervisor when it fails to communicate with active supervisor - "" C4K_REDUNDANCY-6- ATTEMPTINGTOBECOMEACTIVE 6-Information Attempting to become active supervisor. Informational message on standby supervisor when it fails to communicate with active supervisor and attempts to takeover as active supervisor - "" C4K_REDUNDANCY-6-INIT 6-Information Initializing as [chars] supervisor Informational message regarding the state of the supervisor - "" C4K_REDUNDANCY-6-MODE 6-Information [chars] supervisor initializing for [chars] mode Informational message regarding the redundancy mode of the supervisor - "" C4K_REDUNDANCY-6- SWITCHOVER 6-Information Switchover activity detected changing role from STANDBY to ACTIVE Informational message on standby supervisor when it detects switchover activity - "" C5RSP-3-C5_BADIPC 3-Error bad message received from the NMP An unsolicited in band IPC message was received by the router from the NMP. - LOG_STD_NO_ACTION C5RSP-3-C5_MACADRFAIL 3-Error can't get C5 Line Card Mac Addr An attempt by the RSP to query the C5IP for Vlan 0 IP address failed. - "Try these actions to remedy the problem: Reset the router from the NMP's console. If problems persist please RMA the router and or Catalyst 5000" C5RSP-3-C5_NMPMACADRFAIL 3-Error can't get NMP Mac Addr An attempt by the RSP to query the C5IP for Vlan 0 MAC address failed. - "Try these actions to remedy the problem: Reset the router from the NMP's console. If problems persist please contact Cisco for replacement" C5RSP-3-C5_SAGE0FAIL 3-Error Length error occurred on dma channel 0 A hardware error has occurred on dma channel 0 - "Report this error to your technical support representative." C5RSP-3-C5_SAGE1FAIL 3-Error Length error occurred on dma channel 1 A hardware error has occurred on dma channel 1 - "Report this error to your technical support representative." C5RSP-3-C5IP_SLOTFAIL 3-Error can't get Catalyst 5000 Slot number of router An attempt by the RSP to query the C5IP for theslot it is plugged into has failed. - "Try these actions to remedy the problem: Reset the router from the NMP's console. If problem persists please contact Cisco for replacement." C5RSP-3-CANT_CREATE_VLAN 3-Error vlan [dec] can not be created. media not supported An attempt to create a vlan of a media that is not supported has failed - "Try these actions to remedy the problem: Configure the vlan with a different media type." C5RSP-3-INVALID_LOVE_LETTER 3-Error Invalid loveletter type [dec] sent by c5ip\n IOS is receiving bogus messages from the C5IP. - LOG_STD_RECUR_ACTION C5RSP-3-MAXVLAN_EXCEEDED 3-Error can't configure more than 256 VLANS The Vlan Router product can configure a maximum of 256 vlans. - "Try these actions to remedy the problem: Delete unused vlans before configure new ones." C5RSP-3-NMP_DELETE_VLAN 3-Error having problems deleting vlan [dec] on the NMP In band IPC message to the NMP from the router to delete a vlan has failed. - "Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router" C5RSP-3-NMP_INIT_FAIL 3-Error can't talk to NMP during initialization In band IPC router initialization message to the NMP has failed - "Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router" C5RSP-3-NMP_PROG_FAIL 3-Error NMP won't allow vlan [dec] configuration In band IPC message to the NMP from the router to create a vlan has failed. - "Try these actions to remedy the problem: Check the state of Vlan 0. Check the state of the C5IP via the front panel LED. Check the state of the NMP. Reset the router" C5RSP-3-RSM_NMP_BRIDGE_INVALID 3-Error NMP returned invalid bridge id [dec] for [dec]\n NMP returned invalid bridge id to the RSM - "Make sure that the tr-brf vlan on the RSM is configured on the NMP" C5RSP-3-RSM_NMP_CONFIG_MISMATCH 3-Error RSM NMP mismatch in config for [dec] RSM [dec] NMP [dec]\n There is mismatch in config for this vlan on NMP and RSM - "Make sure that the params for this vlan are the same on NMP and on the RSM" C5RSP-3-UNKNOWN_NMP_PROG 3-Error unknown timer for NMP programming An unknown timer event has expired. - LOG_STD_NO_ACTION C5RSP-6-BRIDGE_AFU 6-Information vlan [dec] could/could not be configured for bridging A Vlan could not be reset with the proper bridging information. - "Try these actions to remedy the problem: Configure the vlan with or with bridging." C5RSP-6-NOSWIDB 6-Information vlan [dec] missing IDB Internal data structure of the Vlan is missing. - LOG_STD_ACTION C5RSP-6-VLAN_INFO_MISSING 6-Information vlan [dec] info errant. something very wrong Internal information about the Vlan is missing. - LOG_STD_ACTION CABLE_CLC-3-CONFIG_MISMATCH 3-Error Card type mismatch. config: [chars] is not consistent with the working mode in slot [dec] There are several scenarios that the error message will be reported. Some cases can be recovered by CLC auto reloading. Eg. Kobal-R can work as 10GE or 100GE ifmod for DPIC-G2. If system reload with card pre-configured as DPIC-G2-10GE 'card /0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' while .board.conf was saved as DPIC-G2 100GE mode and Kobal boot up before card precfg parsing. Some cases need to shut down the lc first then change the configuration or change the pic card Eg. if the card is pre-configured as RPHY with the command 'card /0 cBR-CCAP-LC-40G r-phy' but a rf-pic card was inserted to the same slot. Or the card is pre-configured as ICMTS with the command 'card /0 cBR-CCAP-LC-40G' but a dpic card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G2 with the command 'card /0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' but a DPIC-G1 card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G1 with the command 'card /0 CBR-CCAP-LC-G2-R r-phy' but a DPIC-G2 card was inserted to the same slot. cmts-platform-infra LOG_STD_ACTION CABLE_CLC-3-UNSUPPORTED_DATA 3-Error Data conversion error [chars] 0x%X An internal software error has occured when converting the data specified in the message from one representation to another. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION CABLE_CLC-4-LCLOG_PARSE_ERR 4-Warning Error parsing logger message: [chars] from subslot [dec]/[dec] The carrier card passed down a logger message that could not be parsed. cmts-platform-infra LOG_STD_ACTION CABLE_CLC-4-LCLOG_TOOLONG 4-Warning Message too long from slot [dec]/[dec]: [dec] bytes The carrier card passed down a logger message that is too long for\n\ the RP to handle. cmts-platform-infra LOG_STD_ACTION CABLE_CLC-4-LOGGERMSGTOOBIG 4-Warning Logger message length [dec] bytes exceeds the maximum allowed size The carrier card attempted to send a large message to the Route Processor cmts-platform-infra LOG_STD_ACTION CABLE_CLC-5-LOGGER_LC_REMOVED 5-Notice Carrier Card [dec] removed The carrier card was removed cmts-platform-infra LOG_STD_NO_ACTION CABLE_UTIL-4-DC_INVOKE_ERR 4-Warning Dynamic Command [chars] invoke failure There are several scenarios that the error message will be reported. One case is line card boot up mode for different PIC type does not match to pre-configured PIC type. There two modes of the line card : ICMTS&RPHY and Kobal-R can work with DPIC-G1 or DPIC-G2 with different FW. Eg. if the card is pre-configured as RPHY with the command 'card /0 cBR-CCAP-LC-40G r-phy' but a rf-pic card was inserted to the same slot. Or the card is pre-configured as ICMTS with the command 'card /0 cBR-CCAP-LC-40G' but a dpic card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G2 with the command 'card /0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-' but a DPIC-G1 card was inserted to the same slot. Or DPIC type is pre-configured as DPIC-G1 with the command 'card /0 CBR-CCAP-LC-G2-R r-phy' but a DPIC-G2 card was inserted to the same slot. Another case is Kobal-R working ifmod mismatch to precfg. Eg. if system reload with card pre-configured as DPIC-G2-10GE 'card /0 CBR-CCAP-LC-G2-R r-phy DPIC-G2-10GE' while .board.conf was saved as DPIC-G2 100GE mode and Kobal boot up before card precfg parsing then this error message will be reported however it can be recovered by CLC auto reloading. DDTS_COMPONENT "change the pre-config to another mode" "or replace the pic card" CAC-3-MODIFY_FAIL 3-Error CAC is enabled and per-flow rate modification results in CAC inconsistency. Remove and reapply CAC action in the class. This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases. qos LOG_STD_ACTION CAC-3-MODIFY_FAIL 3-Error CAC is enabled and per-flow rate modification results in CAC inconsistency. Remove and reapply CAC action in the class. This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases. qos LOG_STD_ACTION CAC-3-QOS_MODIFY_FAIL 3-Error CAC is already functioning and configuration modification results in CAC inconsistency. Remove and reapply CAC action in the class. This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases. qos LOG_STD_ACTION CAC-3-QOS_MODIFY_FAIL 3-Error CAC is already functioning and configuration modification results in CAC inconsistency. Remove and reapply CAC action in the class. This is an issue in CAC. Probable cause: CAC state update fails. Check internal data bases. qos LOG_STD_ACTION CAC-6-MODIFY 6-Information CAC is already functioning and configuration of per flow [dec] kbps will restart CAC invalidating CAC status for all flows. This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary. qos LOG_STD_ACTION CAC-6-MODIFY 6-Information CAC is already functioning and configuration of per flow [dec] kbps will restart CAC invalidating CAC status for all flows. This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary. qos LOG_STD_ACTION CAC-6-QOS_MODIFY 6-Information CAC is already functioning and a configuration modification will restart CAC invalidating current status for all flows. This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary. qos LOG_STD_ACTION CAC-6-QOS_MODIFY 6-Information CAC is already functioning and a configuration modification will restart CAC invalidating current status for all flows. This is a user modification. Active CAC flows will all unadmitted till reneg. After reneg flow admit/un-admit status may vary. qos LOG_STD_ACTION CALL_CONTROL-3-CCAPI_DB_ERR 3-Error ccapi database error Internal CCAPI conference or call record database error. This message represents an internal software fault and may manifest itself as dropped or hung calls. voice-callcontrol "Contact your technical support representative include the full text of\n\ the error message." CALL_CONTROL-3-CCAPI_DB_ERR 3-Error ccapi database error Internal CCAPI conference or call record database error. This message represents an internal software fault and may manifest itself as dropped or hung calls. voice-callcontrol "Contact your technical support representative include the full text of\n\ the error message." CALL_CONTROL-3-INVALID_PARAMETER 3-Error An invalid parameter is passed to the function This is due to coding error. voice-callcontrol "No action is required for the users" CALL_CONTROL-3-INVALID_PARAMETER 3-Error An invalid parameter is passed to the function This is due to coding error. voice-callcontrol "No action is required for the users" CALL_CONTROL-3-NORAWMSG 3-Error no free raw msg structure available from [chars] for signaling message There were no rawmsg structures remaining in the system pools to alert the\n\ router of a voice or signaling event. voice-callcontrol "Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port." CALL_CONTROL-3-NORAWMSG 3-Error no free raw msg structure available from [chars] for signaling message There were no rawmsg structures remaining in the system pools to alert the\n\ router of a voice or signaling event. voice-callcontrol "Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port." CALL_CONTROL-3-STAT_MEMORY_CORRUPTED 3-Error Memory corruption detected in memory=[hec] allocated for RTCP statistic This is due to coding error voice-callcontrol "No action is required for the users" CALL_CONTROL-3-STAT_MEMORY_CORRUPTED 3-Error Memory corruption detected in memory=[hec] allocated for RTCP statistic This is due to coding error voice-callcontrol "No action is required for the users" CALL_CONTROL-6-APP_NOT_EXIST 6-Information The requested application does not exist any more. The event for the callid [dec] is being discarded.\n The event points to a session application which does not exist any more. The event is being discarded. voice-callcontrol "No action is required for the users" CALL_CONTROL-6-APP_NOT_EXIST 6-Information The requested application does not exist any more. The event for the callid [dec] is being discarded.\n The event points to a session application which does not exist any more. The event is being discarded. voice-callcontrol "No action is required for the users" CALL_CONTROL-6-APP_NOT_FOUND 6-Information Application [chars] in dial-peer [dec] not found. Handing callid [dec] to the alternate app [chars].\n The inbound dial-peer points to an unavailable application. The call is being handed to the alternate application or is rejected. voice-callcontrol "Reconfigure the dial-peer to have a valid application name or verify " "the application is accesible at its location." CALL_CONTROL-6-APP_NOT_FOUND 6-Information Application [chars] in dial-peer [dec] not found. Handing callid [dec] to the alternate app [chars].\n The inbound dial-peer points to an unavailable application. The call is being handed to the alternate application or is rejected. voice-callcontrol "Reconfigure the dial-peer to have a valid application name or verify " "the application is accesible at its location." CALL_CONTROL-6-CALL_LOOP 6-Information The incoming call has a global identifier already present in the list of currently handled calls. It is being refused.\n The incoming call has a global identifier already present in the list of currently handled calls. It means that the voice gateway has detected a loop in the call route. voice-callcontrol "Please check your configuration." CALL_CONTROL-6-CALL_LOOP 6-Information The incoming call has a global identifier already present in the list of currently handled calls. It is being refused.\n The incoming call has a global identifier already present in the list of currently handled calls. It means that the voice gateway has detected a loop in the call route. voice-callcontrol "Please check your configuration." CALL_CONTROL-6-MAX_CONNECTIONS 6-Information Maximum number of connections reached for dial-peer [dec]\n The dial-peer in question has reached its maximum connections configurations. No more calls will be taken on this dial-peer. voice-callcontrol "No action is required however to increase the number of connections " "allowed to this dial peer see 'maximum connections' configuration under " "the dial-peer configuration mode." CALL_CONTROL-6-MAX_CONNECTIONS 6-Information Maximum number of connections reached for dial-peer [dec]\n The dial-peer in question has reached its maximum connections configurations. No more calls will be taken on this dial-peer. voice-callcontrol "No action is required however to increase the number of connections " "allowed to this dial peer see 'maximum connections' configuration under " "the dial-peer configuration mode." CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH 6-Information The called number numbering type did not match The event for the callid [dec] is being discarded.\n The event points to a session application which does not exist any more. The event is being discarded. voice-callcontrol "No action is required for the users" CALL_CONTROL-6-NUMBERING_TYPE_NO_MATCH 6-Information The called number numbering type did not match The event for the callid [dec] is being discarded.\n The event points to a session application which does not exist any more. The event is being discarded. voice-callcontrol "No action is required for the users" CALL_CONTROL-6-UNKNOWN_EXT_AGENT_RESET_ATTEMPT 6-Information Request to reset an uknown external agent ID [dec] attempted. A request to reset an external agent eg H323 Gatekeeper or MGCP CA etc voice-callcontrol LOG_STD_ACTION CALL_CONTROL-6-UNKNOWN_EXT_AGENT_RESET_ATTEMPT 6-Information Request to reset an uknown external agent ID [dec] attempted. A request to reset an external agent eg H323 Gatekeeper or MGCP CA etc voice-callcontrol LOG_STD_ACTION CALL_HOME-3-CALL_HOME_FAILED_TO_ENABLE 3-Error Failed to enable call-home from Smart Agent for Licensing: [chars] Failed to enable call-home from Smart Agent for Licensing. Call-home and Smart Licensing could not work properly. call-home "Please enable call-home manually according to the error string." CALL_HOME-3-CALL_HOME_FAILED_TO_ENABLE 3-Error Failed to enable call-home from Smart Agent for Licensing: [chars] Failed to enable call-home from Smart Agent for Licensing. Call-home and Smart Licensing could not work properly. call-home "Please enable call-home manually according to the error string." CALL_HOME-3-CLI_CMD_RUN_FAILED 3-Error No VTY connection available to run CLI command for event notification message ERR [dec] [chars] - - - CALL_HOME-3-CLI_CMD_RUN_FAILED 3-Error No VTY connection available to run CLI command for event notification message ERR [dec] [chars] - - - CALL_HOME-3-CREATE_EVENT_FAILED 3-Error Failed to create [chars] event for profile [chars] The call-home event creation failed. call-home "Unsubscribe and then subscribe again to that alert group for " "the specified profile." CALL_HOME-3-CREATE_EVENT_FAILED 3-Error Failed to create [chars] event for profile [chars] The call-home event creation failed. call-home "Unsubscribe and then subscribe again to that alert group for " "the specified profile." CALL_HOME-3-DS_DIR_CREATE_FAIL 3-Error Failed to create diagnostic-signature directory [chars] fail reason: [chars]. The diagnostic-signature directory creation failed. call-home "Please check the disk/flash status first and then create the " "diagnostic-signature directory by yourself." CALL_HOME-3-DS_DIR_CREATE_FAIL 3-Error Failed to create diagnostic-signature directory [chars] fail reason: [chars]. The diagnostic-signature directory creation failed. call-home "Please check the disk/flash status first and then create the " "diagnostic-signature directory by yourself." CALL_HOME-3-DS_UPDATE_FAIL 3-Error The call-home diagnostic-signature failed to update. The call-home diagnostic-signature failed to update. call-home "Please check the \"show call-home diagnostic-signature failure\" " "command for details." CALL_HOME-3-DS_UPDATE_FAIL 3-Error The call-home diagnostic-signature failed to update. The call-home diagnostic-signature failed to update. call-home "Please check the \"show call-home diagnostic-signature failure\" " "command for details." CALL_HOME-3-FAIL_TO_RETRIEVE_SCH_STATUS 3-Error Fail to retrieve device registration result. Please check SCH registration status with \call-home request registration-info\ under EXEC mode. Fail to retrieve device registration result. Call-home will abort polling progress. call-home "Please check SCH registration status with \"call-home request " "registration-info\" under EXEC mode." CALL_HOME-3-FAIL_TO_RETRIEVE_SCH_STATUS 3-Error Fail to retrieve device registration result. Please check SCH registration status with \call-home request registration-info\ under EXEC mode. Fail to retrieve device registration result. Call-home will abort polling progress. call-home "Please check SCH registration status with \"call-home request " "registration-info\" under EXEC mode." CALL_HOME-3-HTTP_REQUEST_FAILED 3-Error Failure to send HTTP request to: [chars] ERR [dec] : [chars] - - - CALL_HOME-3-HTTP_REQUEST_FAILED 3-Error Failure to send HTTP request to: [chars] ERR [dec] : [chars] - - - CALL_HOME-3-MESSAGE_SIZE_OVER_LIMIT 3-Error XML message size over limit failed to send call-home message. configured message size limit [dec] is less than current message Unable to create message because configured message size limit is smaller than current message minimum length required. call-home "Please re-config the destination message-size-limit." CALL_HOME-3-MESSAGE_SIZE_OVER_LIMIT 3-Error XML message size over limit failed to send call-home message. configured message size limit [dec] is less than current message Unable to create message because configured message size limit is smaller than current message minimum length required. call-home "Please re-config the destination message-size-limit." CALL_HOME-3-ONDEMAND_MESSAGE_FAILED 3-Error The call-home on-demand message failed to send for [chars][chars]s The call-home on-demand message failed. call-home "Reconfigure call-home to send call-home on-demand messages." CALL_HOME-3-ONDEMAND_MESSAGE_FAILED 3-Error The call-home on-demand message failed to send for [chars][chars]s The call-home on-demand message failed. call-home "Reconfigure call-home to send call-home on-demand messages." CALL_HOME-3-REQUEST_MESSAGE_FAILED 3-Error call-home request message failed to send ERR [dec] [chars] - - - CALL_HOME-3-REQUEST_MESSAGE_FAILED 3-Error call-home request message failed to send ERR [dec] [chars] - - - CALL_HOME-3-SMTP_SEND_FAILED 3-Error Unable to send notification using all SMTP servers ERR [dec] [chars] - - - CALL_HOME-3-SMTP_SEND_FAILED 3-Error Unable to send notification using all SMTP servers ERR [dec] [chars] - - - CALL_HOME-4-HTTP_ADDRESS_NOT_SUPPORTED 4-Warning Http will be or has been disabled on Smart Call Home Server please change the address [chars] to https address for profile [chars]. Otherwise call-home will fail to send messages Http will be or has benn disabled on Smart Call Home Server call-home will fail to send message to the http destination call-home "Please change the http address to https address." CALL_HOME-4-HTTP_ADDRESS_NOT_SUPPORTED 4-Warning Http will be or has been disabled on Smart Call Home Server please change the address [chars] to https address for profile [chars]. Otherwise call-home will fail to send messages Http will be or has benn disabled on Smart Call Home Server call-home will fail to send message to the http destination call-home "Please change the http address to https address." CALL_HOME-4-MESSAGE_IS_TRUNCATED 4-Warning message size over limit call-home message is truncated. configured message size limit [dec] is less than current message call-home message is truncated because configured message size limit is smaller than current message total length required. call-home "Please re-config the destination message-size-limit." CALL_HOME-4-MESSAGE_IS_TRUNCATED 4-Warning message size over limit call-home message is truncated. configured message size limit [dec] is less than current message call-home message is truncated because configured message size limit is smaller than current message total length required. call-home "Please re-config the destination message-size-limit." CALL_HOME-5-DS_ACTION_MSG 5-Notice Notification message from diagnostic-signature file [chars]: [chars] Notification message from call-home diagnostic-signature because the message action defined in it was performed. call-home "No action is required." CALL_HOME-5-DS_ACTION_MSG 5-Notice Notification message from diagnostic-signature file [chars]: [chars] Notification message from call-home diagnostic-signature because the message action defined in it was performed. call-home "No action is required." CALL_HOME-5-HTTPS_NOT_SUPPORTED 5-Notice This image version does not support HTTPS This image does not support secure HTTP although user configures https url call-home "Please upgrade your system image to a crypto image which supports" "secure http." CALL_HOME-5-HTTPS_NOT_SUPPORTED 5-Notice This image version does not support HTTPS This image does not support secure HTTP although user configures https url call-home "Please upgrade your system image to a crypto image which supports" "secure http." CALL_HOME-5-SL_MESSAGE_FAILED 5-Notice Fail to send out Smart Licensing message to: [chars] ERR [dec] : [chars] - - - CALL_HOME-5-SL_MESSAGE_FAILED 5-Notice Fail to send out Smart Licensing message to: [chars] ERR [dec] : [chars] - - - CALL_HOME-6-CALL_HOME_ENABLED 6-Information Call-home is enabled by Smart Agent for Licensing. Call-home is enabled by Smart Agent for Licensing. call-home "No action is required." CALL_HOME-6-CALL_HOME_ENABLED 6-Information Call-home is enabled by Smart Agent for Licensing. Call-home is enabled by Smart Agent for Licensing. call-home "No action is required." CALL_HOME-6-DS_PROFILE_HTTP_NOT_SET 6-Information The Email transport method is currently selected for the Smart Call Home service. To download the Diagnostic Signature from the Smart Call Home Server the HTTP transport method must be enabled and a destination HTTP URL must be configured in the [chars] profile. The call-home diagnostic-signature update will not start because the HTTP transport method is disabled or the URL destination is not configured in the diagnostic-signature profile. call-home "This message is informational only." CALL_HOME-6-DS_PROFILE_HTTP_NOT_SET 6-Information The Email transport method is currently selected for the Smart Call Home service. To download the Diagnostic Signature from the Smart Call Home Server the HTTP transport method must be enabled and a destination HTTP URL must be configured in the [chars] profile. The call-home diagnostic-signature update will not start because the HTTP transport method is disabled or the URL destination is not configured in the diagnostic-signature profile. call-home "This message is informational only." CALL_HOME-6-DS_REMEDIATION_ACTION 6-Information The call-home diagnostic-signature [chars] action was performed. Device status such as configuration or line card status may be affected. The call-home diagnostic-signature remediation actions were performed call-home "No action is required." CALL_HOME-6-DS_REMEDIATION_ACTION 6-Information The call-home diagnostic-signature [chars] action was performed. Device status such as configuration or line card status may be affected. The call-home diagnostic-signature remediation actions were performed call-home "No action is required." CALL_HOME-6-DS_UNDECLARED_VARS 6-Information There're undeclared variables referenced in DS [chars] please use \show call-home diagnostic-signature variables\ to check it. If they're environment variables please configure them to make DS work as expected. call-home DS file has undeclared variables.It will not work until users configure it. call-home "Please check undeclared variables in the DS." CALL_HOME-6-DS_UNDECLARED_VARS 6-Information There're undeclared variables referenced in DS [chars] please use \show call-home diagnostic-signature variables\ to check it. If they're environment variables please configure them to make DS work as expected. call-home DS file has undeclared variables.It will not work until users configure it. call-home "Please check undeclared variables in the DS." CALL_HOME-6-DS_UPDATE_SUCCESS 6-Information call-home diagnostic-signature successfully did [chars] download [dec] new diagnostic-signatures will be added call-home diagnostic-signature downloaded successfully. call-home "No action is required." CALL_HOME-6-DS_UPDATE_SUCCESS 6-Information call-home diagnostic-signature successfully did [chars] download [dec] new diagnostic-signatures will be added call-home diagnostic-signature downloaded successfully. call-home "No action is required." CALL_HOME-6-REQUEST_MESSAGE_SUCCEEDED 6-Information call-home request message succeeded call-home request message was sent successfully. call-home "No action is needed. This is informational message." CALL_HOME-6-REQUEST_MESSAGE_SUCCEEDED 6-Information call-home request message succeeded call-home request message was sent successfully. call-home "No action is needed. This is informational message." CALL_HOME-6-SCH_REGISTRATION_IN_PROGRESS 6-Information Device registration with Smart Call HomeSCH is in progress. SCH device registration is in progress after a Smart licensing registration message was received. Call-home will poll SCH server for the registration result. call-home "No action is required." CALL_HOME-6-SCH_REGISTRATION_IN_PROGRESS 6-Information Device registration with Smart Call HomeSCH is in progress. SCH device registration is in progress after a Smart licensing registration message was received. Call-home will poll SCH server for the registration result. call-home "No action is required." CALL_HOME-6-UPDATE_SCH_REGISTRATION_STATUS 6-Information Device SCH registration result: [chars]. The result has no impact on Smart Licensing registration. You can check Smart Licensing registration status by executing command \show license summary\. Call-home retrieved and printed out the registration result from SCH server. call-home "No action is required." CALL_HOME-6-UPDATE_SCH_REGISTRATION_STATUS 6-Information Device SCH registration result: [chars]. The result has no impact on Smart Licensing registration. You can check Smart Licensing registration status by executing command \show license summary\. Call-home retrieved and printed out the registration result from SCH server. call-home "No action is required." CALL_MGMT-1-CALL_LIST 1-Alert [chars] The specific message text is supplied by the Call Management\n\ software. This indicates that internal data was corrupted\n\ due to a software error - LOG_STD_SH_TECH_ACTION CALL_MGMT-1-CPM_Q_POOL 1-Alert [chars] The specific message text is supplied by the Call Management\n\ software. This indicates a memory exhaustion condition. - LOG_STD_REDUCE_ACTION CALL_MGMT-1-INITSYS 1-Alert [chars] The specific message text is supplied by the Call Management\n\ software. This indicates an initialization failure. When this\n\ occurs the Call Management subsystem is not operational. - LOG_STD_ACTION CALL_MGMT-4-CALL_DISC 4-Warning [chars] The specific message text is supplied by the Call Management\n\ software. This indicates that a call record is missing from\n\ active call list - LOG_STD_ACTION CALLPROG-3-API_INIT 3-Error api front init failed for [chars] Failed to get free element from front end queue. Call Progress Notification "Platform requires additional free elements to properly function.\n\ Stop using Call Progress Notification applications.\n\ Call TAC to report the problem" CALLRECORD-3-MCOM_TERSE_CALL_FAILED_REC 3-Error [chars] Terse Mcom Call Failed Record modem-management LOG_STD_NO_ACTION CALLRECORD-3-MCOM_TERSE_CALL_REC 3-Error [chars] Terse Mcom Call Record modem-management LOG_STD_NO_ACTION CALLRECORD-3-MICA_TERSE_CALL_FAILED_REC 3-Error [chars] Terse Mica Call Failed Record modem-management LOG_STD_NO_ACTION CALLRECORD-3-MICA_TERSE_CALL_REC 3-Error [chars] Terse Mica Call Record modem-management LOG_STD_NO_ACTION CALLRECORD-3-MODEM_CALL_REC_ERROR 3-Error [chars] Record Generated Exceeded Syslog Capability modem-management LOG_STD_NO_ACTION CALLRECORD-3-MODEM_CALL_REC_ERROR 3-Error [chars] Record Generated Exceeded Syslog Capability modem-management LOG_STD_NO_ACTION CALLRECORD-6-MICA_TERSE_CALL_FAILED_REC 6-Information [chars] Terse Mica Call Failed Record modem-management LOG_STD_NO_ACTION CALLRECORD-6-MICA_TERSE_CALL_REC 6-Information [chars] Terse Mica Call Record modem-management LOG_STD_NO_ACTION CALLTREAT_NOSIGNAL-3-HIGH_CPU_5SEC_LOAD 3-Error System experiencing high cpu utilization.\n System does not have enough CPU resources available to allocate \n\ a new resource. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the call threshold global cpu-5sec \n\ command." CALLTREAT_NOSIGNAL-3-HIGH_CPU_5SEC_LOAD 3-Error System experiencing high cpu utilization.\n System does not have enough CPU resources available to allocate \n\ a new resource. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the call threshold global cpu-5sec \n\ command." CALLTREAT_NOSIGNAL-3-HIGH_CPU_AVERAGE_LOAD 3-Error System experiencing high average cpu utilization.\n Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the call threshold\n\ poll-interval command the system does not have \n\ enough CPU resources available to accept a new call. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the show proc\n\ cpu command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the call threshold global cpu-avg\n\ command." CALLTREAT_NOSIGNAL-3-HIGH_CPU_AVERAGE_LOAD 3-Error System experiencing high average cpu utilization.\n Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the call threshold\n\ poll-interval command the system does not have \n\ enough CPU resources available to accept a new call. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the show proc\n\ cpu command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the call threshold global cpu-avg\n\ command." CALLTREAT_NOSIGNAL-3-HIGH_CPU_ONE_MIN_LOAD 3-Error System experiencing high cpu utilization over one minute interval.\n Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ resource allocation if the five-second CPU utilization on the gateway exceeds 98%. " CALLTREAT_NOSIGNAL-3-HIGH_CPU_ONE_MIN_LOAD 3-Error System experiencing high cpu utilization over one minute interval.\n Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ resource allocation if the five-second CPU utilization on the gateway exceeds 98%. " CALLTREAT_NOSIGNAL-3-HIGH_IOMEM_USAGE 3-Error System running low on I/O memory.\n The system does not have enough free I/O memory. call-treatment "Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global io-mem command." CALLTREAT_NOSIGNAL-3-HIGH_IOMEM_USAGE 3-Error System running low on I/O memory.\n The system does not have enough free I/O memory. call-treatment "Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global io-mem command." CALLTREAT_NOSIGNAL-3-HIGH_MEMORY_USAGE 3-Error System running low on memory. The system does not have enough free memory to allocated new resource. call-treatment "Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ call threshold global total-mem command." CALLTREAT_NOSIGNAL-3-HIGH_MEMORY_USAGE 3-Error System running low on memory. The system does not have enough free memory to allocated new resource. call-treatment "Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ call threshold global total-mem command." CALLTREAT_NOSIGNAL-3-HIGH_PROCMEM_USAGE 3-Error System running low on processor memory.\n The system does not have enough free processor memory. call-treatment "Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT_NOSIGNAL-3-HIGH_PROCMEM_USAGE 3-Error System running low on processor memory.\n The system does not have enough free processor memory. call-treatment "Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT_NOSIGNAL-3-HIGH_TOTAL_CALLS 3-Error High call volume.\n The system is experiencing a high call volume. call-treatment "Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT_NOSIGNAL-3-HIGH_TOTAL_CALLS 3-Error High call volume.\n The system is experiencing a high call volume. call-treatment "Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT-3-HIGH_CPU_5SEC_LOAD 3-Error System experiencing high cpu utilization. Processing for callID[dec] is rejected.\n System does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the call threshold global cpu-5sec \n\ command." CALLTREAT-3-HIGH_CPU_5SEC_LOAD 3-Error System experiencing high cpu utilization. Processing for callID[dec] is rejected.\n System does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming the most CPU\n\ capacity and if appropriate reduce other system activity to \n\ ease CPU demands. By default the system will reject calls \n\ if the five-second CPU utilization on the gateway exceeds 89%. \n\ The default value can be overridden by enabling call treatment \n\ and entering the call threshold global cpu-5sec \n\ command." CALLTREAT-3-HIGH_CPU_AVERAGE_LOAD 3-Error System experiencing high average cpu utilization. Processing for callID[dec] is rejected.\n Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the call threshold\n\ poll-interval command the system does not have \n\ enough CPU resources available to accept a new call. The specified \n\ call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the show proc\n\ cpu command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the call threshold global cpu-avg\n\ command." CALLTREAT-3-HIGH_CPU_AVERAGE_LOAD 3-Error System experiencing high average cpu utilization. Processing for callID[dec] is rejected.\n Based on the average CPU utilization over a 60-second interval or an\n\ interval configured through the call threshold\n\ poll-interval command the system does not have \n\ enough CPU resources available to accept a new call. The specified \n\ call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Check to see if the current call setup\n\ rate is supported on this gateway. Enter the show proc\n\ cpu command to see which processes are consuming the \n\ most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%.\n\ The default value can be overridden by enabling call treatment and\n\ entering the call threshold global cpu-avg\n\ command." CALLTREAT-3-HIGH_CPU_ONE_MIN_LOAD 3-Error System experiencing high cpu utilization over one minute interval. Processing for callID[dec] is rejected.\n Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%. " CALLTREAT-3-HIGH_CPU_ONE_MIN_LOAD 3-Error System experiencing high cpu utilization over one minute interval. Processing for callID[dec] is rejected.\n Based on the average CPU utilization over a 60 second interval \n\ the system does not have enough CPU resources available to accept\n\ a new call. The specified call was rejected. call-treatment "Ensure that the call setup rate is within the supported capacity of\n\ this gateway. Enter the show proc cpu\n\ command to see which processes are consuming\n\ the most CPU capacity and if appropriate reduce other system\n\ activity to ease CPU demands. By default the system will reject \n\ calls if the five-second CPU utilization on the gateway exceeds 98%. " CALLTREAT-3-HIGH_IOMEM_USAGE 3-Error System running low on I/O memory. Processing for callID[dec] is rejected.\n The system does not have enough free I/O memory to accept a new call.\n\ The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global io-mem command." CALLTREAT-3-HIGH_IOMEM_USAGE 3-Error System running low on I/O memory. Processing for callID[dec] is rejected.\n The system does not have enough free I/O memory to accept a new call.\n\ The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of I/O memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for I/O memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global io-mem command." CALLTREAT-3-HIGH_MEMORY_USAGE 3-Error System running low on memory. Processing for callID[dec] is rejected.\n The system does not have enough free memory to accept a new call. \n\ The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ call threshold global total-mem command." CALLTREAT-3-HIGH_MEMORY_USAGE 3-Error System running low on memory. Processing for callID[dec] is rejected.\n The system does not have enough free memory to accept a new call. \n\ The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of memory for\n\ this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem \n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ By default the system will reject calls if there is less than 2% free\n\ processor memory on the gateway. This value can be overridden by \n\ enabling call treatment and entering the\n\ call threshold global total-mem command." CALLTREAT-3-HIGH_PROCMEM_USAGE 3-Error System running low on processor memory. Processing for callID[dec] is rejected.\n The system does not have enough free processor memory to accept a new\n\ call. The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT-3-HIGH_PROCMEM_USAGE 3-Error System running low on processor memory. Processing for callID[dec] is rejected.\n The system does not have enough free processor memory to accept a new\n\ call. The specified call was rejected. call-treatment "Ensure that the gateway has the recommended amount of processor memory\n\ for this Cisco IOS feature set and version. Enter the \n\ show mem and show proc mem\n\ commands to see which processes are consuming the\n\ most memory. Check to see if the memory usage is appropriate for these\n\ processes and if so reduce other system activity to ease CPU demands.\n\ The high and low thresholds for processor memory utilization can be\n\ configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT-3-HIGH_TOTAL_CALLS 3-Error High call volume. Processing for callID[dec] is rejected.\n The system is experiencing a high call volume. There are not\n\ enough resources to accept a new call. The specified call was \n\ rejected. call-treatment "Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTREAT-3-HIGH_TOTAL_CALLS 3-Error High call volume. Processing for callID[dec] is rejected.\n The system is experiencing a high call volume. There are not\n\ enough resources to accept a new call. The specified call was \n\ rejected. call-treatment "Disable call threshold modify the call threshold global\n\ high and low values or investigate the cause of the high resource\n\ utilization. The high and low thresholds for total number of calls\n\ can be configured by enabling call treatment and entering the\n\ call threshold global proc-mem command." CALLTRKR-3-CALL_REC_ERROR 3-Error [chars] Record Generated Exceeded Syslog Capability CallTracker LOG_STD_NO_ACTION CALLTRKR-3-NO_MEM 3-Error Memory allocation failed for CT [chars] [dec] bytes Calltracker couldn't allocate new record due to no free memory. CallTracker "Disable calltracker [no calltracker enable]. Run show memory to\n\ find out where is the memory been allocated." CALLTRKR-3-PRINT_BUFFER 3-Error calltrkr cli print buffer [chars] calltrkr cli internal print buffer overflow. Calltracker "Stop to using calltrkr show commands call TAC to report the problem" CALLTRKR-3-PROC 3-Error can't spawn [chars] Couldn't spawn calltracker process. CallTracker "Disable calltracker first [no calltracker enable] enable it again." CALLTRKR-6-CALL_RECORD 6-Information [chars] Terse CallTracker Call Record CallTracker LOG_STD_NO_ACTION CALLTRKR-6-MODEM_CALL_REC 6-Information [chars] Modem Verbose CallTracker Call Record CallTracker LOG_STD_NO_ACTION CALLTRKR-6-MODEM_INFO_CALL_REC 6-Information [chars] Modem Information Verbose CallTracker Call Record CallTracker LOG_STD_NO_ACTION CALLTRKR-6-MODEM_LINE_CALL_REC 6-Information [chars] Modem Line Verbose CallTracker Call Record CallTracker LOG_STD_NO_ACTION CALLTRKR-6-MODEM_NEG_CALL_REC 6-Information [chars] Modem Negotiation Verbose CallTracker Call Record CallTracker LOG_STD_NO_ACTION CAPCHANGE_DYNAMIC-4-LDP 4-Warning ERRMSG_NOFLAGS - - - CAPCHANGE_DYNAMIC-4-LDP 4-Warning ERRMSG_NOFLAGS - - - CAPCHANGE-4-LDP 4-Warning ERRMSG_NOFLAGS - - - CAPCHANGE-4-LDP 4-Warning ERRMSG_NOFLAGS - - - CAPWAP_FRAG-2-UNENABLED 2-Critical [chars] feature not enabled at interface [chars] packet cannot be processed Capwap Fragmentation feature as indicated not enabled by the control plane. This is a critical problem. qfp LOG_STD_ACTION CAPWAP_FRAG-3-CAPWAP_FRAG_DBG 3-Error Capwap Fragmentation encountered an error: [chars] [chars] %lu [chars] %lu Capwap Fragmentation encountered a runtime error as indicated in the message with parameter data for debug qfp LOG_STD_ACTION CAPWAP_FRAG-3-CAPWAP_FRAG_ERR 3-Error Capwap Fragmentation encountered an error: [chars] Capwap Fragmentation encountered a runtime error as indicated qfp LOG_STD_ACTION CAPWAP_FRAG-3-INIT_FAILED 3-Error Initialization of the CAPWAP_FRAG feature in QFP failed Initialization of the CAPWAP_FRAG feature in the QFP failed. This indicates a software failure. qfp LOG_STD_ACTION CAPWAP_FRAG-3-INVALID_QFP_NO 3-Error Invalid qfp device no.: [chars] Invalid qfp device no. qfp LOG_STD_ACTION CAPWAP_REASS_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION CAPWAP_REASS_PROXY-3-PROXY_IPC_MEM_EXTEND_FAILED 3-Error - Increasing of Capwap Reassembly memory pool failed. cpp-ucode LOG_STD_ACTION CAPWAP_REASS_PROXY-3-PROXY_IPC_MEM_INIT_FAILED 3-Error - Initialization of Capwap Reassembly memory pool failed. cpp-ucode LOG_STD_ACTION CAPWAP_REASS_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION CAPWAP_REASS-2-UNENABLED 2-Critical [chars] feature not enabled at interface [chars] packet cannot be processed Capwap Reassembly feature as indicated not enabled by the control plane. This is a critical problem. qfp LOG_STD_ACTION CAPWAP_REASS-3-ALLOC_FAILED 3-Error Allocation of [chars] memory failed for CAPWAP_REASS feature in QFP Allocation of memory by the QFP CAPWAP_REASS feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure qfp LOG_STD_ACTION CAPWAP_REASS-3-CAPWAP_REASS_DBG 3-Error Capwap Reassembly encountered an error: [chars] [chars] %lu [chars] %lu Capwap Reassembly encountered a runtime error as indicated in the message with parameter data for debug qfp LOG_STD_ACTION CAPWAP_REASS-3-CAPWAP_REASS_ERR 3-Error Capwap Reassembly encountered an error: [chars] Capwap Reassembly encountered a runtime error as indicated qfp LOG_STD_ACTION CAPWAP_REASS-3-INIT_FAILED 3-Error Initialization of the CAPWAP_REASS feature in QFP failed Initialization of the CAPWAP_REASS feature in the QFP failed. This indicates a software failure. qfp LOG_STD_ACTION CAPWAP_REASS-3-INVALID_QFP_NO 3-Error Invalid qfp device no.: [chars] Invalid qfp device no. qfp LOG_STD_ACTION CAPWAP_REASS-3-MEM_INIT_FAILED 3-Error - Failure occurred initializing capwap reass memory pool. qfp LOG_STD_ACTION CAPWAP_REASS-3-MEM_REQ_FAILED 3-Error - IPC Failure occurred when attempting to request more capwap reass pool memory. qfp LOG_STD_ACTION CARD_PROTECTION-3-BOTH_ACTIVE 3-Error For Card protection group: [dec] both primary and backup are active DS1844 potentiometer initialization failed. It indicates a hardware failure gsr-oc3_12-pos-spa "Change the hardware or copy the error message exactly as it " "appears and report it to your technical support representative." CARD_PROTECTION-4-ACTIVE 4-Warning Card protection group: [dec] is [chars] ACTIVE [chars] whether card protection group is ACTIVE - "None - normal situation" CARD_PROTECTION-4-CONFIG_ADD 4-Warning [chars] [dec]/[dec] Member added to Card protection group [dec] New Member added to Card protection group - "None - normal situation" CARD_PROTECTION-4-CONFIG_GROUP 4-Warning CARD_PROTECTION-Group [dec] is configured Card Protection group is configured - "None - normal situation" CARD_PROTECTION-4-CONFIG_VIRTUAL 4-Warning Virtual IM [dec]/[dec] is created Virtual IM is created for Card protection group - "None - normal situation" CARD_PROTECTION-4-PROTECTION 4-Warning Card protection group: [dec] [chars] [dec]/[dec] is [chars] [chars] Protection Switchover between members of group - "None - normal situation" CARD_STATE-3-CARD_UNSUPPORT 3-Error Card in slot [dec] with type [chars] is not supported in version [dec].[dec] The linecard inserted does not supported in currently running software. cbr-platform-infra "Replace the unsupported card or upgrade to right " "software." CARD_STATE-3-TYPE_MISMATCH 3-Error Mismatched card type [chars] in slot [dec]. Expected type [chars]. The linecard inserted does not match the currently provisioned card type. cbr-platform-infra "Replace wrong board type with currently provisioned " "board type or type 'no card' to allow new card " "type to be discovered." CARD_STATE-3-UNEXPECTED 3-Error Unexpected error on slot [dec]: [chars] An unexpected error has occured while performing a linecard OIR action cbr-platform-infra LOG_STD_ACTION CARD_STATE-4-FORCE_RESET 4-Warning Reset slot [dec] for reason: [chars] The SUP forced a linecard to reload for the reason. cmts-platform-infra LOG_STD_ACTION CARD_STATE-4-INCONSISTANT 4-Warning Gemini version inconsistant: slot [dec] daughter board [dec] version [chars] slot [dec] daughter board [dec] version [chars] Different Gemini in chassis CBR only supports the same hardware version US modules. cmts-platform-infra "Replace the Gemini to let the version " "of the Gemini in two slots be the same." CARD_STATE-4-LEOBEN_MISMATCH 4-Warning Leoben version mismatch: slot [dec] version [chars] slot [dec] version [chars] Different Leoben in chassis CBR only supports the same hardware version US modules. cbr-platform-infra "Replace the Leoben to let the version " "of the Leoben in two slots be the same." CARRIER-2-CT3_E1_MIX 2-Critical Cannot mix E1 PRI and CT3 DFC in chassis\ do not power up invalid card in slot [dec]\n The user has put E1 PRI and CT3 DFC cards in the same chassis. - "Remove the extra E1 PRI or CT3 DFC card." CARRIER-2-T1_E1_MIX 2-Critical Cannot mix T1 and E1 8PRI DFC cards in chassis\ do not power up invalid card in slot [dec]\n The user has put T1 and E1 8PRI DFC cards in the same chassis. - "Remove the extra T1 or E1 8PRI DFC card." CARRIER-2-THREE_NP108_NOT_PRESENT 2-Critical 3 NP108s were not found on Tetryl card [dec] detected. Tetryl requires 3 NP108s to be present tetryl LOG_STD_ACTION CARRIER-2-TOOMANY_8PRI 2-Critical Too many 8PRI DFC cards do not power up invalid card in slot [dec]\n The user has put too many 8PRI DFC cards in the chassis. - "Remove the extra 8PRI DFC card." CARRIER-2-TOOMANY_CT3 2-Critical Too many CT3 DFC cards do not power up invalid card in slot [dec]\n The user has put too many CT3 DFC cards in the chassis. - "Remove the extra CT3 DFC card or 8PRI DFC card causing problem" CARRIER-2-TOOMANY_TRUNK 2-Critical Too many trunk DFC cards do not power up invalid card in slot [dec]\n The user has put too many trunk DFC cards in the chassis. - "Remove the extra trunk DFC card." CARRIER-3-DFC_INIT_ALREADY 3-Error DFC is already initialized - DFC [dec] DFC is already initialized no need to initialize again as LOG_STD_ACTION CARRIER-3-DFC_INIT_FAIL 3-Error DFC initialization is failed - DFC [dec] DFC initialization is failed because of several reasons as LOG_STD_ACTION CARRIER-3-DFC_POWER_INT 3-Error DFC Power Changed - DFC [dec] DFC Power is fluctuating as LOG_STD_ACTION CARRIER-3-INVALID_DFC 3-Error Invalid DFC - DFC [dec] type [dec] DFC has invalid board id/type as LOG_STD_ACTION CARRIER-3-PLATFORM_DFC 3-Error DFC Carrier Platform Init Failed - Slot [dec] DFC Carrier Platform Init Failed as LOG_STD_ACTION CARRIER-3-POWER_DFC 3-Error DFC Power-On Failed - DFC [dec] DFC Power-On Failed as LOG_STD_ACTION CARRIER-3-RESET_DFC 3-Error DFC Reset Failed - DFC [dec] During OIR Removal process DFC reset failed. as LOG_STD_ACTION CASA-2-NOMEM 2-Critical Out of memory: [chars]\n CASA failed to allocate memory. casa LOG_STD_REDUCE_ACTION CASA-3-BADVER 3-Error Incoming packet is CASA v[dec] this router is v[dec] A packet was received for the wrong version of CASA casa "Verify that all CASA devices are running the same version \n\of the protocol" CASA-4-BADMSG 4-Warning Message parsing error: [chars] Failed to parse an incoming packet casa "If this message is occurring repeatedly enable 'debug ip casa error'\n\and record the output call your Cisco technical support representative\n\and provide the gathered information." CASA-4-PORTCHANGE 4-Warning Wildcard overlap: [chars] A CASA wildcard received on one port has been overwritten \n\by a service manager sending to another port. This message may appear \n\once if you are migrating your service to a new forwarding-agent port\n\if it recurs it could indicate a configuration problem. casa LOG_STD_RECUR_ACTION CASA-4-SECURITY_FAIL 4-Warning [chars] security information in CASA packet. Security check failed. casa "Make sure all CASA systems are configured with the same password." CASA-4-UNEXPECTED 4-Warning Unexpected error: [chars] An unexpected error occurred while performing CASA operation casa LOG_STD_RECUR_ACTION CASA-4-WARNING 4-Warning Unexpected condition: [chars] An unexpected condition was detected while performing CASA operation casa LOG_STD_RECUR_ACTION CBAC_C3PL-3-INIT 3-Error Firewall data plane updates are disabled The firewall notification of objects to the data plane has failed to\n\ startup and as such data plane updates are disabled. inspect show registry brief CBAC_C3PL-4-OBJ_CREATE 4-Warning Firewall [chars] object [chars] creation failed in the data plane error [dec] The notification of the creation of a firewall object e.g. a parameter\n\ map has failed to update the data plane and as such the application\n\ of the parameters contained within the object will not be applied to\n\ the data plane. It is also possible that the common classification\n\ may fail to locate and bind to the object rendering the configuration\n\ incomplete in terms of application. inspect show memory CBAC_C3PL-4-OBJ_DELETE 4-Warning Firewall [chars] object [chars] deletion failed in the data plane error [dec] The notification of the deletion of a firewall object e.g. a parameter\n\ map has failed to update the data plane and as such the application\n\ of the parameters contained within the object may continue to be\n\ applied to the data plane. inspect show memory CBAC_C3PL-4-OBJ_MODIFY 4-Warning Firewall [chars] object [chars] modification failed in the data plane error [dec] The notification of the modification of a firewall object e.g. a\n\ parameter map has failed to update the data plane and as such the\n\ application of the parameters contained within the object will not be\n\ applied to the data plane. inspect show memory CBERR-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - CBERR-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - CBR_LIC-3-APPLY_DS_FAILED 3-Error Applying downstream license failed Unable to apply the downstream license cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-3-APPLY_LCHA_FAILED 3-Error Enforcement failed Unable to enforce cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-3-APPLY_US_FAILED 3-Error Applying upstream license failed Unable to apply the upstream license cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-3-APPLY_WAN_FAILED 3-Error Applying upstream license failed Unable to apply the upstream license cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-3-CPB_OPEN_FAILED 3-Error Failed to open CPB data file for reading and/or writing Unable to open CPB data file cmts-application "Please report to TAC" CBR_LIC-3-CPB_READ_FAILED 3-Error Reading CPB data file failed Unable to read CPB data from file cmts-application "Please report to TAC" CBR_LIC-3-CPB_SEEK_FAILED 3-Error Setting file position failed Unable to set file position for reading and/or writing cmts-application "Please report to TAC" CBR_LIC-3-CPB_WRITE_FAILED 3-Error Writing CPB data file failed Unable to write CPB data to file cmts-application "Please report to TAC" CBR_LIC-3-CSB_FAIL 3-Error [chars] Failed for [chars] An attempt to parse a license related CLI failed cmts-application "Check the linecard license details and call TAC" CBR_LIC-3-LIC_SA_MALLOC_FAILED 3-Error [chars] Platform malloc for Smart License Agent failed cmts-application "Check the mem usage and report to TAC" CBR_LIC-3-LIC_SA_NULL_FUN_PTR 3-Error [chars] Platform getting a null function pointer from Smart License Agent cmts-application "Report to TAC" CBR_LIC-3-LIC_SA_REGISTER_FAILED 3-Error [chars] Smart License Agent registr failed cmts-application "Check call-home pki vrf config and the IdToken" CBR_LIC-3-NULL_LICENSE_ENTITLEMENT 3-Error License entitlement DB is NULL! The DS license DB is NULL cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-3-NULL_LICENSE_INFO 3-Error License DB is NULL! The license DB is NULL cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-4-CPB_LESS_RECORD 4-Warning In [chars] [dec] UTC CPB samples loss is more than [dec][dec] hours CPB samples are less than expected. cmts-application "If it is not the first month apply CPB feature " "or maintenance window is no more than 5 hours. Please report to TAC" CBR_LIC-4-CPB_SN_MISMATCH 4-Warning CPB data will be removed since they are from Chassis: [chars]. Local Chassis is: [chars]. CPB records were saved in other Chassis. cmts-application "This is informational message." CBR_LIC-5-CPB_EVENT_LOG 5-Notice CPB event: [chars] Important event for CPB feature. cmts-application "This is informational message." CBR_LIC-6-CHAN_NOSHUTFAIL 6-Information [chars] channel [dec] no shut is not allowed due to insufficient licenses Unable to no shut the channel due to insufficient licenses cmts-application "Procure more licenses report to TAC" CBR_LIC-6-CHANNEL_NO_SHUTDOWN 6-Information [chars]:[dec] has been restored to no shut Restored previously shutdown channels to no shut state cmts-application "None" CBR_LIC-6-CHANNEL_SHUTDOWN 6-Information [chars]:[dec] has been shutdown due to deactivated enforcement Channel shut due to enforcement cmts-application "Buy additional licenses. Please report to TAC" CBR_LIC-6-DS_LIC_ENFORCED 6-Information enforce_en:[dec] [chars] is [dec] License contract violation! Enforced cmts-application "Buy consumed additional licenses and report to TAC" CBR_LIC-6-DS_LIC_RESTRICTED 6-Information [chars] [chars]:[dec] [chars] License contract violation! License Restricted/Enforced cmts-application "Buy additional licenses and report to TAC" CBR_LIC-6-LCHA_CHANNEL_NO_SHUTDOWN 6-Information [chars] has been restored to no shut Restored previously shutdown channels to no shut state cmts-application "None" CBR_LIC-6-LCHA_CHANNEL_SHUTDOWN 6-Information [chars] Channel shut due to enforcement cmts-application "Buy additional licenses. Please report to TAC" CBR_LIC-6-LCHA_LIC_ENFORCED 6-Information enforce_en:[dec] [chars] is [dec] License contract violation! Enforced cmts-application "Buy consumed additional licenses and report to TAC" CBR_LIC-6-LCHA_LIC_RESTRICTED 6-Information [chars] [chars] License contract violation! License Restricted/Enforced cmts-application "Buy additional licenses and report to TAC" CBR_LIC-6-LIC_CAP_LIMIT_BELOW_CONSUMED 6-Information [chars] Capped count cannot be set! Consumed count is higher cmts-application "Capped count cannot be set! " "Consumed count is higher" CBR_LIC-6-LIC_CAPPED_DURATION_EXPIRED 6-Information Capped Enforcement duration expired. Deactivated Enforced Capped Enforcement duration expired after an Eval or Grace expired cmts-application "Restore communication with cisco and add " "entitlements if required" CBR_LIC-6-LIC_CAPPED_DURATION_TIMER_STARTED 6-Information License [chars] period has expired. Capped enforcement is active. The router will be deactivated in 90 days Eval or Grace Period has expired. Capped enforced - Will be deactivated in 90 days cmts-application "Restore communication with cisco and add " "entitlements if out of compliance" CBR_LIC-6-LIC_CONFIG_LOCKED 6-Information [chars] Configuration lock in effect! Please register the cBR and try cmts-application "Configuration lock in effect! " "Register the cBR and try" CBR_LIC-6-LIC_LIMIT_NOT_SUPPORT 6-Information [chars] Don't support Capped Enforcement for this license tag cmts-application "License limits cannot be changed for this feature" CBR_LIC-6-LIC_LIMIT_SET_ALREADY 6-Information [chars] To change license limits disable license limits first cmts-application "License limits cannot be changed " " without disbling license limits first" CBR_LIC-6-LIC_OOC_DURATION_EXPIRED 6-Information OOC duration expired - Capped Enforced OOC duration has expired and hence capped enforced cmts-application "Add entitlements to stay in compliance" CBR_LIC-6-LIC_OOC_DURATION_TIMER_STARTED 6-Information License OOC timer has started. All entitlements will be Capped Enforced in 270 days. Please add necessary entitlements OOC duration timer has started. All entitlements will be Capped Enforced in 270 days. cmts-application "Add necessary entitlements to stay in compliance" CBR_LIC-6-LIC_SA_DISABLED 6-Information [chars] License contract is violated. The device is disabled cmts-application "Report to TAC and add sufficient licenses" CBR_LIC-6-LIC_SA_EVAL_EXPIRED 6-Information [chars] Eval Period has expired. License agent moving to eval-expired state cmts-application "Restore communication with cisco and register " " the device" CBR_LIC-6-LIC_SA_GLOBAL_NOTIFICATION 6-Information [chars] A global notification about an event change in the Smart License Agent was received cmts-application "None" CBR_LIC-6-LIC_SA_GRACE_EXPIRED 6-Information [chars] Grace Period has expired. License agent moving to garce-expired state cmts-application "Restore communication with cisco" CBR_LIC-6-LIC_SA_IN_COMPLIANCE 6-Information [chars] Smart License Agent enforcement mode changed to Incompliance cmts-application "None" CBR_LIC-6-LIC_SA_OUT_OF_COMPLIANCE 6-Information [chars] Smart License Agent enforcement mode changed to out of compliance cmts-application "Report to TAC and add sufficient licenses" CBR_LIC-6-LIC_SA_OVERAGE 6-Information [chars] Smart License Agent enforcement mode changed to overage cmts-application "Report to TAC and add sufficient licenses" CBR_LIC-6-LICENSE_ENFORCE 6-Information Enforcement mode set to [chars] License Information has been applied cmts-application "No action required" CBR_LIC-6-OUT_OF_RANGE 6-Information [chars] is out of range:[dec] License counters have reached boundary condition cmts-application "Please copy traceback infomation and report to TAC" CBR_LIC-6-US_CHANNEL_NO_SHUTDOWN 6-Information [chars] has been restored to no shut Restored previously shutdown channels to no shut state cmts-application "None" CBR_LIC-6-US_CHANNEL_SHUTDOWN 6-Information [chars] has been shutdown due to deactivated enforcement Channel shut due to enforcement cmts-application "Buy additional licenses. Please report to TAC" CBR_LIC-6-US_LIC_ENFORCED 6-Information enforce_en:[dec] [chars] is [dec] License contract violation! Enforced cmts-application "Buy consumed additional licenses and report to TAC" CBR_LIC-6-US_LIC_RESTRICTED 6-Information [chars] [chars] [chars] License contract violation! License Restricted/Enforced cmts-application "Buy additional licenses and report to TAC" CBR_LIC-6-WAN_CHANNEL_NO_SHUTDOWN 6-Information [chars] has been restored to no shut Restored previously shutdown channels to no shut state cmts-application "None" CBR_LIC-6-WAN_CHANNEL_SHUTDOWN 6-Information [chars] has been shutdown due to deactivated enforcement Channel shut due to enforcement cmts-application "Buy additional licenses. Please report to TAC" CBR_LIC-6-WAN_LIC_ENFORCED 6-Information enforce_en:[dec] [chars] is [dec] License contract violation! Enforced cmts-application "Buy consumed additional licenses and report to TAC" CBR_LIC-6-WAN_LIC_RESTRICTED 6-Information [chars] [chars] [chars] License contract violation! License Restricted/Enforced cmts-application "Buy additional licenses and report to TAC" CBR_MCAST-3-SF_RECOVER 3-Error Sfid [dec] Recover failed on [chars]. An internal software error occurred. cbr-cmts-apps LOG_STD_SH_TECH_ACTION CBR_PLFM_HA-3-CHKPTADDCLIENT 3-Error Check Point Client [dec] Add Failed - [dec] Failed to add checkpoint client ubr-sw LOG_STD_ACTION CBR_PLFM_HA-3-GET_DATA_PTR 3-Error [chars]: checkpoint get data pointer error Checkpoint infra get message data pointer failed ubr-sw LOG_STD_ACTION CBR_PLFM_HA-3-REPL 3-Error Failed to setup [chars] chasfs reason: [chars] Failed to create replication manager related chasfs entry which is used to trigger database sync ubr-sw LOG_STD_ACTION CBR_PLFM_HA-3-STATESYNC 3-Error Redundancy state synchronization failure [dec]/[dec] - [chars] A failure occurred in trying to synchronize CBR platform information ubr-sw LOG_STD_ACTION CBR_PLFM_HA-3-STBY_FP_ERR 3-Error Standby FP failed to reach sso-ready within tolerated wait time Standby FP failed to reach sso-ready within tolerated wait time ubr-sw LOG_STD_ACTION CBR_PLFM_HA-3-STBY_PLL_NOT_LOCK 3-Error Standby PLL failed to lock active within tolerated wait time Standby PLL failed to lock active within tolerated wait time ubr-sw LOG_STD_ACTION CBR_PLFM_HA-6-STATE_CC 6-Information Lincard [dec] will be reloaded - [chars] Lincard is not ready for sup-ha ubr-sw LOG_STD_NO_ACTION CBR_PTP-3-DISPATCH 3-Error Unable to dispatch received TDL message from PTP daemon This is an Event from RPD cbr-ptp LOG_STD_NO_ACTION CBR_PTP-3-INITFAIL 3-Error Failed to initalize required PTP resource: [chars] During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated. cbr-ptp LOG_STD_ACTION CBR_PTP-3-NITFAIL 3-Error Failed to initalize required PTP resource: [chars] During the initialization of the resources required by PTP a failure occured. This has prevented PTP from being activated. cbr-ptp LOG_STD_ACTION CBR_PTP-5-TOD_CHG 5-Notice The TOD source changed: [chars] The source of time of day changed: 1. from GPS of SUP-PIC 0/1 2. from DTI of SUP-PIC 0/1 3. free run mode cbr-ptp LOG_STD_NO_ACTION CBR_SPA-0-DPIC_EMERG 0-Emergency [chars]-[chars] Receive some EMERG message from DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-1-DPIC_ALERT 1-Alert [chars]-[chars] Receive some ALERT message from DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-2-DPIC_CRIT 2-Critical [chars]-[chars] Receive some CRITICAL message from DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-3-CORTINA_PHY_DEV_ATTACH_ERROR 3-Error [chars] Cortina PHY device attach error port [dec]/[dec]/[dec] Unable to attach Cortina PHY device object - LOG_STD_SH_TECH_ACTION CBR_SPA-3-CORTINA_PHY_DEV_CREATE_ERROR 3-Error [chars] Cortina PHY device create error port [dec]/[dec]/[dec] Unable to create Cortina PHY device object - LOG_STD_SH_TECH_ACTION CBR_SPA-3-CORTINA_PHY_DEV_INIT_ERROR 3-Error [chars] Cortina PHY device init error port [dec]/[dec]/[dec] Unable to downaload firmware to Cortina PHY device - LOG_STD_SH_TECH_ACTION CBR_SPA-3-DPIC_BOOT_REASON 3-Error DPIC [dec]/[dec]: [chars] DPIC Boot Error Reason - LOG_STD_SH_TECH_ACTION CBR_SPA-3-DPIC_ERR 3-Error [chars]-[chars] Receive some ERR message from DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-3-DPIC_NGIO_ERROR 3-Error NGIO connection between IOMd and DPIC [dec]/[dec] is down! NGIO is down between IOMd and DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-3-DPIC_NGIO_KEEPALIVE 3-Error NGIO keepalive between IOMd and DPIC [dec]/[dec] timeout! \%lu NGIO rx %lu ping successes %lu ping failures NGIO keepalive is timeout. - LOG_STD_SH_TECH_ACTION CBR_SPA-3-DTI_CLIENT_DNLD_ERROR 3-Error [chars] DTI Client error Unable to download DTI client firmware - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_CLK_NOT_RDY_ERR 3-Error [chars] Falcon ESI Clocks reg:0x%08x Falcon-ESI clocks are NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_CLOCK_NOT_READY_ERROR 3-Error [chars] Raptor ESI Clocks reg:0x%08x Raptor-ESI clocks are NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_NOT_READY_ERROR 3-Error [chars] Raptor ESI Global Ready reg:0x%08x Raptor-ESI NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PIC_PWR_NOT_GOOD_ERR 3-Error [chars] Falcon SUP PIC Power not good Falcon-ESI PLL not locked - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PIC_PWR_NOT_GOOD_ERROR 3-Error [chars] Raptor SUP PIC Power not good Raptor-ESI PLL not locked - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PIC_STATUS_REG_READ_ERR 3-Error [chars] unable to read from Falcon ESI PIC STATUS REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PIC_STATUS_REG_READ_ERROR 3-Error [chars] unable to read from Raptor ESI PIC STATUS REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_LOCK_ERR 3-Error [chars] unable to lock Falcon ESI PLL Falcon-ESI PLL not locked - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_LOCK_ERROR 3-Error [chars] unable to lock Raptor ESI PLL Raptor-ESI PLL not locked - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_REG_READ_ERR 3-Error [chars] unable to read from Falcon ESI PLL CONTROL REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_REG_READ_ERROR 3-Error [chars] unable to read from Raptor ESI PLL CONTROL REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_REG_WR_ERR 3-Error [chars] unable to write to Falcon ESI PLL CONTROL REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_PLL_CTRL_REG_WRITE_ERROR 3-Error [chars] unable to write to Raptor ESI PLL CONTROL REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_RDY_REG_READ_ERR 3-Error [chars] unable to read Falcon ESI READY REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_READY_REG_READ_ERROR 3-Error [chars] unable to read Raptor ESI READY REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_SUP_CHASSIS_SLOT_REG_WR_ERR 3-Error [chars] unable to write to Falcon ESI CHASSIS SLOT ID REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_SUP_CHASSIS_SLOT_REG_WRITE_ERROR 3-Error [chars] unable to write to Raptor ESI CHASSIS SLOT ID REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_SUP_CTRL_REG_WR_ERR 3-Error [chars] unable to write to Falcon ESI CONTROL REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-ESI_SUP_CTRL_REG_WRITE_ERROR 3-Error [chars] unable to write to Raptor ESI CONTROL REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_EGR_BUF_LOCAL_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from EGRESS LOCAL BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_EGR_BUF_PEER_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from EGRESS REMOTE BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_EGR_DISPATCH_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from EGRESS DISPATCH\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_ESI_CLOCK_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from CLOCK\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_ESI_PCIE_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_FP_EGR_SCH_TOP_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from FP\n\ EGRESS SCHDULER TOP Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_FP_INGR_PAR_TOP_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from FP\n\ INGRESS PARSER TOP Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_INGR_BUF_LOCAL_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from INGRESS LOCAL BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_INGR_BUF_PEER_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from INGRESS REMOTE BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_INGR_PARSER_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from INGRESS PARSER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_INGR_SCH_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from INGRESS SCHDULER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_INIT_ERROR 3-Error [chars] Falcon err [dec] Falcon driver initialization error - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_MAC_ENTRY_FULL 3-Error [chars] Falcon [chars] mac-filter entry full drop addr %02X.%02X.%02X.%02X.%02X.%02X Falcon mac filter entry full - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_MAC_LOCAL_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from LCOAL MAC\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_MAC_PEER_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from PEER MAC\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_MODE_XCVR_MATCH_ERR 3-Error SUP-PIC [dec]/1 port [dec] interface mode mismatched: QSFP type is [chars] interface mode is [chars] SUP250 backhaul interface support two kinds of transceiver: QSFP28 and QSFP+. If the backhaul mode is configured as 100GE mode with commad 'cable sup250-ifmod 100GE' but insert a QSFP+ transceiver. Or the backhaul mode is configured as 10GE mode with comand 'cable sup250-ifmod 10GE' but insert a QSFP28 transceiver. This error message will be reported. - "Change configration to another backhaul mode or replace other type of transceiver." CBR_SPA-3-FALCON_PAR_RST_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from PAR RST\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_PLL_LOS 3-Error [chars] Falcon PLL LOS - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_PMBIST_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from PM BIST\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-FALCON_SEM_HI_INTERRUPT 3-Error [chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec] HIGH Priority Interrupt received from SEM\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_CFG_REG_WRITE_ERROR 3-Error [chars] unable to write to Raptor MAC RX/TX CFG REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_CLK_NOT_RDY_ERR 3-Error [chars] Falcon MAC Clocks reg:0x%08x Falcon-MAC clocks are NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_CLOCK_NOT_READY_ERROR 3-Error [chars] Raptor MAC Clocks reg:0x%08x Raptor-MAC clocks are NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_NOT_RDY_ERR 3-Error [chars] Falcon MAC Global reg:0x%08x Falcon-MAC Contrpl Plane NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_NOT_READY_ERROR 3-Error [chars] Raptor MAC Global reg:0x%08x Raptor-MAC Contrpl Plane NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_PIC_CPLD_NOT_RDY_ERR 3-Error [chars] Falcon MAC PIC CPLD error Falcon-MAC PIC CPLD NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_PIC_CPLD_NOT_READY_ERROR 3-Error [chars] Raptor MAC PIC CPLD error Raptor-MAC PIC CPLD NOT Ready - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_PIC_CTRL_REG_WR_ERR 3-Error [chars] unable to write to Falcon MAC PIC CONTROL REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_PIC_CTRL_REG_WRITE_ERROR 3-Error [chars] unable to write to Raptor MAC PIC CONTROL REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_READY_REG_READ_ERR 3-Error [chars] unable to read Falcon MAC READY REG err [dec] Unable to communicate with Falcon Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-MAC_READY_REG_READ_ERROR 3-Error [chars] unable to read Raptor MAC READY REG err [dec] Unable to communicate with Raptor Device driver - LOG_STD_SH_TECH_ACTION CBR_SPA-3-NULL_SPA_PTR 3-Error - Pointer to a SPA object is NULL. - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_CLOCK_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from Clock\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_INGRESS_SCH_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from Ingress Scheduler\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_PCIE_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from PCIE Wrapper\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_PROCBUS_MASTER_HI_INTERRUPT 3-Error [chars] [chars] HIGH Priority Interrupt received from ProcBus Master\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_PRST_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received Partial reset\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_ESI_SERDES_PKTBUS_HI_INTERRUPT 3-Error [chars] [chars] Hign Priority Interrupt received from Serdes PktBus\n\ Module in Raptor-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_INIT_ERROR 3-Error [chars] Raptor err [dec] Raptor driver initialization error - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_LED_ERROR 3-Error SUP-PIC [dec]/[dec] LED err SUP-PIC LED initialization error - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_CLOCK_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from Clock\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_DNLD_FAILED 3-Error [chars] Raptor-MAC error Unable to download Raptor-MAC firmware - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_ENTRY_FULL 3-Error [chars] Raptor [chars] mac-filter entry full drop addr %02X.%02X.%02X.%02X.%02X.%02X Raptor mac filter entry full - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_FIFO_CTL_HI_INTERRUPT 3-Error [chars] [chars] HIGH Priority Interrupt received from FIFO Control\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_MDIO_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from MDIO\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_PROCBUS_SLAVE_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from ProcBus Slave\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_PRST_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received Partial reset\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_RLDRAM_HI_INTERRUPT 3-Error [chars] [chars] HIGH Priority Interrupt received from RLDRAM\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_SERDES_PKTBUS_HI_INTERRUPT 3-Error [chars] [chars] HIGH Priority Interrupt received from Serdes PktBus\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_MAC_XFI_IF_HI_INTERRUPT 3-Error [chars] [chars] High Priority Interrupt received from XFI\n\ Module in Raptor-MAC FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_PLL_LOS 3-Error [chars] Raptor PLL LOS - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RAPTOR_PRST_HIT_CONSTANT_CRC 3-Error Detected continual CRC errors on SUP-PIC [dec]/1 port [dec] or port [dec]! SUP160 backhaul interface's recover service was blocked because there are continual CRC errors on corresponding interface. - "Check related link including fiber line SFP module etc..." CBR_SPA-3-RAPTOR_SEM_HI_INTERRUPT 3-Error [chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec] HIGH Priority Interrupt received from SEM\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RETIMER_PHY_DEV_ATTACH_ERROR 3-Error [chars] Retimer PHY device attach error quad [dec]/[dec]/[dec] Unable to attach Retimer PHY device object - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RETIMER_PHY_DEV_CREATE_ERROR 3-Error [chars] Retimer PHY device create error quad [dec]/[dec]/[dec] Unable to create Retimer PHY device object - LOG_STD_SH_TECH_ACTION CBR_SPA-3-RETIMER_PHY_DEV_INIT_ERROR 3-Error [chars] Retimer PHY device init error quad [dec]/[dec]/[dec] Unable to init Retimer PHY device - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SFP_SUB_INIT_ERROR 3-Error [chars] SFP Subblock create error Unable to create SFP sub-block - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_DPIC_UPGRADE_NOSPACE 3-Error no enough space in harddisk to store digital pic image \[dec]MB free [dec]MB needed\n DIGI PIC firmware can not be upgraded\n\ due to harddisk is full\n - "Free up some space in harddisk to \store digital pic image." CBR_SPA-3-SPA_PLUGIN_INIT_ABORT_ERROR 3-Error [chars] SPA Plugin Init Abort error Unknown SPA Init phase - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_RFSW_I2C_FAILURE 3-Error I2C failure on [dec]/[dec] I2C status:[chars] An I2C failure error received from RFSW PIC\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_RFSW_POWER_ERROR 3-Error Power circuit error on [dec]/[dec] voltages:[chars] A power circuit error received from RFSW PIC\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_RFSW_RELAY_FAILURE 3-Error Relay failure on [dec]/[dec] relay status:[chars] A Relay failure error received from RFSW PIC\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_RFSW_TEMPERATURE_ERROR 3-Error Temperature Error on [dec]/[dec] temperature:[chars] A Temperature error received from RFSW PIC\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_RFSW_UPGRADE_UNSUPPORTED 3-Error unsupported firmware upgrade on [dec]/[dec] firmware version :[hec]\n RFSW PIC firmware can not be upgraded\n - LOG_STD_SH_TECH_ACTION CBR_SPA-3-SPA_UNKN_INIT_ERROR 3-Error [chars] Unknown SPA Init phase error Unknown SPA Init phase - LOG_STD_SH_TECH_ACTION CBR_SPA-3-XCVR_MISSING_HWIDB_ERROR 3-Error [chars] XCVR Missing interface object port [dec]/[dec]/[dec] Unable to downaload firmware to Cortina PHY device - LOG_STD_SH_TECH_ACTION CBR_SPA-3-XCVR_POP_DEF_PARAMS_ERROR 3-Error [chars] XCVR Unable to poulate default parameters port [dec]/[dec]/[dec] Unable to poulate default XCVR SM parameters - LOG_STD_SH_TECH_ACTION CBR_SPA-3-XCVR_SM_LAUNCH_ERROR 3-Error [chars] XCVR Unable to launch SM port [dec]/[dec]/[dec] Unable to launch XCVR SM - LOG_STD_SH_TECH_ACTION CBR_SPA-4-DPIC_WARNING 4-Warning [chars]-[chars] Receive some WARNING message from DPIC - LOG_STD_SH_TECH_ACTION CBR_SPA-4-FALCON_PLL_MIS 4-Warning [chars] Falcon PLL clock soure not come from active RP\n - LOG_STD_SH_TECH_ACTION CBR_SPA-4-RAPTOR_PLL_MIS 4-Warning [chars] Raptor PLL clock soure not come from active RP\n - LOG_STD_SH_TECH_ACTION CBR_SPA-4-SPA_RFSW_WATCH_DOG_TIMEOUT 4-Warning Watch Dog Timeout on [dec]/[dec] A Watch Dog Timeout error received from RFSW PIC\n - LOG_STD_SH_TECH_ACTION CBR_SPA-5-DPIC_NOTICE 5-Notice [chars]-[chars] Receive some NOTICE message from DPIC - LOG_STD_NO_ACTION CBR_SPA-5-DPIC_RESET 5-Notice DPIC [dec]/[dec] will be recovered from unexpected state DPIC can not be online in 5 min - LOG_STD_NO_ACTION CBR_SPA-6-DPIC_INFO 6-Information [chars]-[chars] Receive some INFO message from DPIC - LOG_STD_NO_ACTION CBR_SPA-6-SPA_DPIC_UPGRADE_UNSUPPORTED 6-Information unsupported firmware upgrade on [dec]/[dec]\n DIGI PIC firmware can not be upgraded\n - LOG_STD_SH_TECH_ACTION CBR_SPA-7-DPIC_DEBUG 7-Debug [chars]-[chars] Receive some DEBUG message from DPIC - LOG_STD_DBG_ACTION CBR_SPA-7-FALCON_EGR_BUF_LOCAL_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from EGRESS LOCAL BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_EGR_BUF_PEER_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from EGRESS REMOTE BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_EGR_DISPATCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from EGRESS DISPATCHER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_ESI_FC_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from ESI FC\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_ESI_PCIE_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_ESI_QPLL_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from PCIE Wrapper\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_FP_10G_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from FP 10G\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_FP_EGR_SCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from FP EGRESS SCHEDULER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_FP_INGR_PAR_TOP_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from FP INGRESS PARSER TOP\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_GB_MDIO_IF_HI_INTERRUPT 7-Debug [chars] [chars] High Priority Interrupt received from GB MDIO\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_INGR_BUF_LOCAL_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from INGRESS LOCAL BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_INGR_BUF_PEER_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from INGRESS REMOTE BUF\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_INGR_PARSER_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from INGRESS PARSER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_INGR_SCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from INGRESS SCHEDULER\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_INTERRUPT_DISABLE 7-Debug Interrupt throttled for: [chars] [chars] Interrupt throttled\n - LOG_STD_DBG_ACTION CBR_SPA-7-FALCON_INTERRUPT_ENABLE 7-Debug Interrupt enabled for: [chars] [chars] Interrupt unthrottled\n - LOG_STD_DBG_ACTION CBR_SPA-7-FALCON_MAC_LOCAL_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from LOCAL MAC\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_MAC_PEER_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from REMOTE MAC\n\ Module in Falcon FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_PAR_RST_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from PAR RST\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_PWM_DIST_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from PWM DIST\n\ Module in Falcon-ESI FPGA - LOG_STD_SH_TECH_ACTION CBR_SPA-7-FALCON_SEM_LO_INTERRUPT 7-Debug [chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec] Low Priority Interrupt received from SEM\n - LOG_STD_SH_TECH_ACTION CBR_SPA-7-RAPTOR_ESI_EGRESS_HDR_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Egress\n\ Header Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_EGRESS_SCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Egress\n\ Scheduler Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_FC_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Flow\n\ Control Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_INGRESS_SCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Ingress\n\ Scheduler Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_PCIE_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from PCIE Wrapper\n\ Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_PROCBUS_MASTER_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from ProcBus Master\n\ Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_PRST_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received Partial reset\n\ Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_ESI_SERDES_PKTBUS_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Serdes PacketBus\n\ Module in Raptor-ESI FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_INTERRUPT_DISABLE 7-Debug Interrupt throttled for: [chars] [chars] Interrupt throttled\n - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_INTERRUPT_ENABLE 7-Debug Interrupt enabled for: [chars] [chars] Interrupt unthrottled\n - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_10G_MAC_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from 10GE MAC\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_FIFO_CTL_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from FIFO Control\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_FIFO_CTRL_MUX_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from FIFO Control MUX\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_INGRESS_QOS_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Ingress QoS\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_MAC_SCH_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from MAC Scheduler\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_PROCBUS_SLAVE_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Proc Bus\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_PRST_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received Partial reset\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_RLDRAM_IF_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from RLDRAM Interface\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_MAC_SERDES_PKTBUS_LO_INTERRUPT 7-Debug [chars] [chars] Low Priority Interrupt received from Serdes Packet Bus\n\ Module in Raptor-MAC FPGA - LOG_STD_DBG_ACTION CBR_SPA-7-RAPTOR_SEM_LO_INTERRUPT 7-Debug [chars] [chars] err_report_reg 0x[hec] stat_reg 0x[hec] Low Priority Interrupt received from SEM\n - LOG_STD_DBG_ACTION CBR_VIDEO-3-LED_NO_RESOURCE 3-Error LED Subsystem Init Failed Logical Edge Device subsystem init failed video-cp "Verify system memory and check is the image correct." CBR_VIDEO-6-LOGICAL_EDGE_DEVICE 6-Information LED [dec] [chars]. Logical Edge Device Process terminated/restarted video-cp "LOG_STD_NO_ACTION" CBRCCE-3-CBR_DP_CFR_ADD_ERR 3-Error Failed to add cfr for CM [enet] cfr id [dec] sfref [dec] sfid [dec] rc [dec] Mostly caused by cfr chunk exhausted or cm_qos not found cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_DYN_QOS_ERR 3-Error Failed to commit dynamic qos for CM [enet] sfid [dec] rc [dec] Mostly caused by dynamic qos bind failure cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_FLOW_ADD_ERR 3-Error Failed to add flow for CM [enet] sfid [dec] rc [dec] Mostly caused by flow or cm_qos chunk exhausted cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_FORW_INTF_SET_ERR 3-Error Failed to set forwarding interface for CM [enet] sfid [dec] rc [dec] Mostly caused by invalid service flow ID cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_JIB_HDR_SET_ERR 3-Error Failed to set JIB header for CM [enet] sfid [dec] rc [dec] Mostly caused by invalid service flow ID cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_LOCK_ERR 3-Error Failed to lock semaphore pid [dec] Mostly caused by a process hogging CPU cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_QOS_PARAMS_SET_ERR 3-Error Failed to set qos parameters for CM [chars] sfid [dec] rc [dec] Mostly caused by invalid service flow ID cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_STA_QOS_ERR 3-Error Failed to commit static qos for CM [enet] rc [dec] Mostly caused by qos bind failure cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-3-CBR_DP_TMP_DEL_ERR 3-Error Failed to remove template from template_list for CM [enet] Mostly caused by template remove failure cbrcce-sw LOG_STD_SH_TECH_ACTION CBRCCE-4-CBR_DP_CFR_PARAM_CONFLICT 4-Warning Classifier's parameters conflict: [chars] Mostly caused by unsupported classifier's parameters combination cbrcce-sw "Please do not configure unsupported classifier's " "parameters or unsupported classifier's parameters combination " "as the error message indicated." CBRDTI-5-DTISLOT 5-Notice DTI slot [dec]/[dec]: card role changed to [chars]\n Change in role of DTI slot dti "Check DTI link/cable" CBRDTI-6-CHG_CLK_REF 6-Information Clock reference source set to [chars] The reasons for the change in clock reference. 1Manual mode configuration command for DTI mode dti "Check reference source of DTI" CBUS-3-ADDRFILTR 3-Error Interface [chars] address filter [chars] command failed code %#04x The specified address filter command sent to the specified\n\ interface failed with the displayed error code. cbus "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-AIPINVPLIM 3-Error Interface [chars] Invalid PLIM detected. Interface downed A software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-BADRXEOFVEC 3-Error [chars] ustatus: [chars] %04x %04x %04x %04x %04x Debugging information when an IP panics. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-BADTXEOFVEC 3-Error [chars] ustatus: [chars] %04x %04x %04x %04x %04x Debugging information when an IP panics. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-BADTXSTATE 3-Error [chars] ustatus: [chars] %04x %04x %04x %04x %04x Debugging information when an IP panics. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-BADVC 3-Error [chars] [dec]/[dec] got bad VC packet \n%08x %08x %08x %08x %08x %08x %08x %08x An interface received a packet with bad VC encapsulation. \n\ This indicates either a software or hardware problem. - LOG_STD_SH_TECH_ACTION CBUS-3-BUFFER 3-Error Controller [dec] Error %-04x Buffersize = [dec] Bufferpool = [dec] number [dec] An internal software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CATMCFG 3-Error Interface [chars] Cannot config interface CBus ATM MEM 0x[hec] status [dec] A software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-CATMRSET 3-Error Interface [chars] Error %-04x [chars] - aip_reset A software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CATMRSETU 3-Error Unit [dec] Error %-04x [chars] - cbus_atm_reset A software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CBUSBCE 3-Error Failed to select a BCE response 0x%04x - cbus_bce_update_ifa A hardware or software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CBUSBCEPERM 3-Error Failed to select a BCE response 0x%04x - cbus_bce_permissions_update A hardware or software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CCBCMDFAIL0 3-Error Controller [dec] cmd [dec] failed 0x%-04x A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-CCBCMDFAIL1 3-Error Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-CCBCMDFAIL3 3-Error Controller [dec] cmd [dec] 0x%-04x 0x%-04x 0x%-04x failed 0x%-04x A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-CCBPTIMEOUT 3-Error CCB handover timed out CCB 0x[hec] slot [dec] A hardware or software error occurred. cwpa "Please gather the logs and tracebacks " "and contact the TAC" CBUS-3-CCBSEMINFO 3-Error CCB semaphore acquired traceback:[chars]\n CCB semaphore released traceback:[chars] More information on the CCB semaphore. The tracebacks indicate the program counters and stack that point to the code that was the last to acquire this semaphore and the last to release this semaphore respectively - LOG_STD_SH_TECH_ACTION CBUS-3-CE3DSX3ERR 3-Error [chars]Illegal E3 value - unit is [dec] - - - CBUS-3-CFGCMDDROPPED 3-Error Config queue is full command was dropped slot [dec] Sending a config command was retried. The receiving\n\ queues were still full after retries therefore the command was dropped. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-CMD 3-Error Cmd failed: [chars] response %#04x [chars] A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-CMDDROPPED 3-Error Cmd dropped CCB 0x[hec] slot [dec] cmd code [dec] A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CMDTIMEOUT 3-Error Cmd timed out CCB 0x[hec] slot [dec] cmd code [dec] A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-CORRUPT 3-Error Controller [dec] wrote 0x%-04x read 0x%-04x loc 0x%-04x - dci_memtest A hardware component failed an internal diagnostic test. - "Replace the malfunctioning device." CBUS-3-CT3DSX3ERR 3-Error [chars]Illegal dsx3 value - unit is [dec] - - - CBUS-3-CT3STAT 3-Error Out of buffers--losing status information for CT3 on VIP card A status information message from the VIP was received.\n\ A memory buffer is required to process the status information \n\ message but the memory allocation routine due to insufficient\n\ system buffer memory. Therefore the status information message\n\ was not processed. This condition may be caused either by a heavy \n\ memory utilization at the time of the memory buffer request or by\n\ insufficient memory in the system. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration. If this \n\ message recurs or appears regularly contact your Cisco technical \n\ representative to upgrade the memory of the system." CBUS-3-CTRACHECK 3-Error Interface [chars] Adapter Check Error %04x %04x %04x %04x The Token Ring monitor firmware detected a fatal error on the\n\ interface card. high-token "Issue a clear interface command. " LOG_STD_RECUR_ACTION CBUS-3-CTRBADLOVE1 3-Error Interface [chars] SRB_COMPLETE lovenote received with unknown command 0x%04x The system received a message from the Token Ring interface\n\ but does not recognize the message. high-token LOG_STD_SH_TECH_ACTION CBUS-3-CTRBADLOVE1_DUMP 3-Error Dump of MEMB follows\n-SRB_ADDR: %04x %04x %04x %04x %04x %04x %04x %04x The system is printing codes related to a previous lovenote error\n\ message. high-token LOG_STD_SH_TECH_ACTION CBUS-3-CTRCMDFAILED 3-Error Interface [chars] CTR Command [chars] Failed [chars] %#04x A command sent from the system to the Token Ring interface failed to\n\ complete successfully. high-token LOG_STD_SH_TECH_ACTION CBUS-3-CTRCMDFAILED2 3-Error Interface [chars] CTR Command [chars] Failed Code %#04x A command sent from the system to the Token Ring interface failed to\n\ complete successfully. high-token LOG_STD_SH_TECH_ACTION CBUS-3-CTRINIT 3-Error Interface [chars] CTR Initialization Failed - [chars] The Token Ring interface failed one of its internal self-tests. - "Issue a clear interface command. " LOG_STD_RECUR_ACTION CBUS-3-CTRLRCMDFAIL0 3-Error Controller [dec] cmd [dec] failed 0x%-04x count [dec] A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-CTRLRCMDFAIL1 3-Error Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x count [dec] A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-CTRRAMTEST 3-Error Interface [chars] RAM Addressing Test Failed - [chars] The Token Ring interface failed its memory diagnostic tests. - "Issue a clear interface command. " LOG_STD_RECUR_ACTION CBUS-3-CTRRSET 3-Error Interface [chars] failed to initialize The Token Ring interface failed to insert into the Token Ring.\n\ The interface is placed into reset state and will not \n\ automatically try to re-insert itself. high-token "Issue a clear interface command. " LOG_STD_RECUR_ACTION CBUS-3-CTRUCHECK 3-Error Interface [chars] Microcode Check Error The Token Ring interface microcode detected an unrecoverable error. high-token "Issue a clear interface command. " LOG_STD_RECUR_ACTION CBUS-3-DAUGHTER 3-Error Unit [dec] daughter controller [dec] failed [chars] test - interface disabled - - "First check that the daughter controller card is properly seated in\n\ its Multibus and ciscoBus connectors. Next swap daughter cards and\n\ check whether the error follows the daughter card or the slot. If the\n\ message recurs call your technical support representative for\n\ assistance." CBUS-3-DAUGHTER_NO_RSP 3-Error Unit [dec] daughter [dec] not responding 0x%04x - disabled - - "First make sure that the daughter card is properly seated in its\n\ Multibus and ciscoBus connectors. If this message recurs copy the \n\ error message exactly as it appears on the console or in the system\n\ log contact your Cisco technical support representative and provide\n\ the representative with the gathered information" CBUS-3-FCICMDFAIL0 3-Error Controller [dec] cmd [dec] failed 0x%-04x count [dec] A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-FCICMDFAIL1 3-Error Controller [dec] cmd [dec] 0x%-08x failed 0x%-04x count [dec] A command sent from the system to an interface processor failed to\n\ complete successfully. - "The system recovered by generating an error code to the requester." CBUS-3-FDDIRSET 3-Error Interface [chars] Error %-04x [chars] - fddi_reset A hardware device did not respond appropriately to a request. - "Make sure the device is functioning and is configured correctly." CBUS-3-FDDIRSETU 3-Error Unit [dec] Error %-04x [chars] - fddi_reset A hardware device did not respond appropriately to a request. - "Make sure the device is functioning and is configured correctly." CBUS-3-FSIPRSET 3-Error Interface [chars] Error %-04x [chars] - fsip_reset - - "Check FSIP electrical connections cable and ciscoBus connections. An\n\ FSIP microcode reload will be required. If the check of electrical\n\ connections reveals no problems and the message recurs call your\n\ technical support representative for assistance." CBUS-3-HALSDHERR 3-Error [chars]Illegal sdh value - unit is [dec] - - - CBUS-3-HALSTAT 3-Error Out of buffers--losing status information for ChSTM-1 on VIP card An internal software resource has been exhausted. - LOG_STD_SH_TECH_ACTION CBUS-3-HSSIRSET 3-Error Interface [chars] Error %-04x [chars] - hssi_reset A command to reset an HSSI interface was issued by the RSP\n\ but the interface did not respond to the command within the\n\ expected time delay. The delay is given for the processor to\n\ return the buffers that it has allocated and to perform any\n\ necessary cleanup. This condition may be caused by a large number\n\ of buffers that have been allocated by the interface due to either\n\ heavy traffic or a hardware problem with the interface. - "Verify that the card is properly seated. If this error recurs \n\ then issue the show tech-support and\n\ show logging commands contact your Cisco \n\ technical support representative and provide the representative\n\ with the gathered information." CBUS-3-INITERR 3-Error Interface [dec] Error %-04x idb %08x [dec] [chars] - cbus_init The switch processor or ciscoBus controller signaled an error while\n\ processing a packet or selecting an interface. This indicates a\n\ software problem. - LOG_STD_SH_TECH_ACTION CBUS-3-INTR 3-Error Interface [dec] idb %08x [dec] [chars] - cbus_interrupt The switch processor or ciscoBus controller returned a nonsensical\n\ value. - LOG_STD_SH_TECH_ACTION CBUS-3-MODULE 3-Error Missing [chars] for [chars] A hardware or software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-NOBUF 3-Error Buffer allocation failure: [chars] A hardware or software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-OUTHUNG 3-Error [chars]: tx[chars] output hung %-04x - [chars] [chars] A transmission attempt on an interface failed. The interface might not\n\ be attached to a cable or there might be a software problem. - "Check that the interfaces are all connected to the proper cables. If\n\ that is not the problem call your technical support representative." CBUS-3-POLLFAIL 3-Error Interface [chars] failed to respond debug info follows A Token Ring interface card failed to respond to periodic polling.\n\ This can indicate a software or hardware problem.\n\ See CBUS-3-POLLFAILDAT for the syntax of this message. - LOG_STD_SH_TECH_ACTION CBUS-3-POLLFAILDAT 3-Error Int [dec]: %04X %04X %04X %04X %04X %04X This is the debugging information for the CBUS-3-POLLFAIL error. - LOG_STD_DBG_ACTION CBUS-3-PORTTYPE 3-Error Unexpected interface type for [chars][dec] port [dec] type [dec] A hardware or software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-POTSTAT 3-Error Out of buffers--losing status information for POTENT on VIP card An internal software resource has been exhausted. - LOG_STD_SH_TECH_ACTION CBUS-3-RESETNXI 3-Error Reset of removed interface [hec] [chars] An interface reset was attempted on an interface that was removed from\n\ the router. This message appears if you use the shutdown command to\n\ bring down a removed interface. - LOG_STD_NO_ACTION CBUS-3-SELECTBADVC 3-Error Select invalid vc number [dec]. An invalid channel number is selected - LOG_STD_SH_TECH_ACTION CBUS-3-SENDIPCMDFAIL 3-Error Send Ip Cmd Failed. Command dropped after [dec] retries CCB 0x[hec] slot [dec] cmd code [dec]\n Sending an ip command was retried. The receiving queues were still\n\ full after retries therefore the command was dropped. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-SERRSET 3-Error Interface [chars] Error %-04x [chars] - serial_reset A software error occurred. - LOG_STD_SH_TECH_ACTION CBUS-3-SRPRSET 3-Error Interface [chars] Error %-04x [chars] - srp_reset A command to reset an SRP interface was issued by the RSP\n\ but the interface did not respond to the command within the\n\ expected time delay. The delay is given for the processor to\n\ return the buffers that it has allocated and to perform any\n\ necessary cleanup. This condition may be caused by a large number\n\ of buffers that have been allocated by the interface due to either\n\ heavy traffic or a hardware problem with the interface. - "Verify that the card is properly seated. If this error recurs \n\ then issue the show tech-support and\n\ show logging commands contact your Cisco \n\ technical support representative and provide the representative\n\ with the gathered information." CBUS-3-TESTFAIL 3-Error Unit [dec] failed [chars] test - interface disabled A hardware component failed an internal diagnostic test. - "Check switch settings on the interface cards. Check for proper unit\n\ numbers. Reset the cards. Replace the malfunctioning device." CBUS-3-TXALLOC 3-Error Error %-04x tx_allocate - cbus_init A hardware device did not respond appropriately to a request. - "Make sure the device is functioning and is configured correctly." CBUS-3-TXSTARTPENDACTIVE 3-Error [chars] ustatus: [chars] %04x %04x %04x %04x %04x Debugging information when an IP panics. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-3-TXVCENCAPFAIL 3-Error Detected bad tx vc encap on [chars] vc [dec]. Board encap failed [hex] [hex] [hex] Board encap failed on a transmit packet on a channelized serial \n\ interface which does not have the vc number encapsulation - LOG_STD_SH_TECH_ACTION CBUS-3-UNKENC 3-Error Interface [chars] unknown encaps type [hec] A packet was received from the CIP with an unknown encapsulation type.\n\ The packet will be dropped. - LOG_STD_SH_TECH_ACTION CBUS-3-UNKNOWN 3-Error [chars] ustatus: [chars] %04x %04x %04x %04x %04x Debugging information when an IP panics. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CBUS-4-CTRBADLOVE2 4-Warning Interface [chars] Unexpected SRB_COMPLETE lovenote command=0x%04x result=0x%04x The system received an unsolicited message from the Token Ring interface.\n\ The system ignored the message and continued normal processing. high-token LOG_STD_RECUR_ACTION CBUS-4-FIXBADTXVC 4-Warning Detected and fixed bad tx vc encap on [chars] bad vc [dec] fixed vc [dec] A transmit packet on a channelized serial interface does not\n\ have the vc number encapsulation - LOG_STD_SH_TECH_ACTION CBUS-4-NOCOOKIE 4-Warning [chars]-[dec] controller missing configuration data - disabled The controller type was derived from a hardware probe. The controller\n\ number indicates the ciscoBus relative slot number. This is a hardware\n\ error - LOG_STD_SH_TECH_ACTION CBUS-4-RSETFAIL 4-Warning Interface [chars] failed to reset properly in [chars] code [hex] An interface reset command failed. This may be a software or hardware\n\ problem. - LOG_STD_SH_TECH_ACTION CBUS-5-CBADVCSETUP 5-Notice Interface [chars] setup vc failed with vci exceeding vc-per-vp - 3 The TI1570 chip reserves 3 RX DMA channels for OAM cells. As a result the last 3 VCIs of the last VPI block cannot be used for regular traffic. - "Avoid try different vci/vpi combinations." CBUS-5-FDDICMD 5-Notice '[chars]' is not supported on [chars] This command is not supported on this FDDI interface. - LOG_STD_NO_ACTION CBUS-5-INPUTERR 5-Notice Interface [chars] excessive input error rate Interface disabled because too many input errors occurred. - "Inspect condition of attached network hardware" CBUS-5-SENDIPCMDRECOV 5-Notice Send Ip Cmd Succeeded after [dec] retries CCB 0x[hec] slot [dec] cmd code [dec]\n Sending an ip command was retried due to receiving queues being full.\n\ But after some retries command was send successfuly. - LOG_STD_NO_ACTION CCE_PI_PD-3-CLASS_NAME 3-Error Map name [chars] id %08X unable to [chars] string [hec] - - - CCE_PI_PD-3-CLASS_NAME 3-Error Map name [chars] id %08X unable to [chars] string [hec] - - - CCE_PI_PD-3-FILTER_LIST 3-Error Failed to create class [chars] id %08X filter list An operation to create the filter list for a particular class has failed due to a resource issue. This may imply that the resultant notification via the API was deferred or dropped. cce "show class-map [type" " ] " CCE_PI_PD-3-FILTER_LIST 3-Error Failed to create class [chars] id %08X filter list An operation to create the filter list for a particular class has failed due to a resource issue. This may imply that the resultant notification via the API was deferred or dropped. cce "show class-map [type" " ] " CCE_PI_PD-4-CLASS_CLASS_GROUP_DB 4-Warning Failed to [chars] class group id %08X class id %08X class group %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group attached to a class successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class-group " CCE_PI_PD-4-CLASS_CLASS_GROUP_DB 4-Warning Failed to [chars] class group id %08X class id %08X class group %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group attached to a class successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class-group " CCE_PI_PD-4-CLASS_DB 4-Warning Failed to [chars] class group id %08X class id %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class group " CCE_PI_PD-4-CLASS_DB 4-Warning Failed to [chars] class group id %08X class id %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class group " CCE_PI_PD-4-CLASS_GROUP_DB 4-Warning Failed to [chars] id %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class-group " CCE_PI_PD-4-CLASS_GROUP_DB 4-Warning Failed to [chars] id %08X [chars] database An operation to manipulate the record of the class groups and classes supplied via the PI/PD API has failed to perform the required action on a class group successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp associations " "class-group " CCE_PI_PD-4-FEATURE_BIND_DB 4-Warning Failed to [chars] target id %08X class group %08X class id %08X feature [chars] binding [chars] database An operation to manipulate the record of the binding of a action within a policy map class to a particular target supplied via the PI/PD API has failed to perform the required action successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp bindings " "target " CCE_PI_PD-4-FEATURE_BIND_DB 4-Warning Failed to [chars] target id %08X class group %08X class id %08X feature [chars] binding [chars] database An operation to manipulate the record of the binding of a action within a policy map class to a particular target supplied via the PI/PD API has failed to perform the required action successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp bindings " "target " CCE_PI_PD-4-TARGET_CLASS_GROUP_DB 4-Warning Failed to [chars] id %08X [chars] database An operation to manipulate the record of the target class groups supplied via the PI/PD API has failed to perform the required action on a target class group successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp bindings " "target " CCE_PI_PD-4-TARGET_CLASS_GROUP_DB 4-Warning Failed to [chars] id %08X [chars] database An operation to manipulate the record of the target class groups supplied via the PI/PD API has failed to perform the required action on a target class group successfully. This may imply that the resultant notification via the API was deferred or dropped. cce "show cce cpdp bindings " "target " CCE_PI_PD-6-CLASS_CLASSES_DB 6-Information Class group %08X class %08X [chars] contains a class group The class is reporting the presence of a class group upon its removal. This is informational. cce "show cce cpdp associations " "class-group " CCE_PI_PD-6-CLASS_CLASSES_DB 6-Information Class group %08X class %08X [chars] contains a class group The class is reporting the presence of a class group upon its removal. This is informational. cce "show cce cpdp associations " "class-group " CCE_PI_PD-6-CLASS_FILTER 6-Information Class [chars] id %08X type [chars] filter list is unbalanced During the addition of a class an internal error was encountered during the construction of the match terms comprising that class. cce "show class-map" " [type ] " CCE_PI_PD-6-CLASS_FILTER 6-Information Class [chars] id %08X type [chars] filter list is unbalanced During the addition of a class an internal error was encountered during the construction of the match terms comprising that class. cce "show class-map" " [type ] " CCE_PI_PD-6-CLASS_GROUP_CLASSES_DB 6-Information Class group %08X contains classes The class group is reporting the presence of classes upon its removal. This is informational. cce "show cce cpdp associations " "class-group " CCE_PI_PD-6-CLASS_GROUP_CLASSES_DB 6-Information Class group %08X contains classes The class group is reporting the presence of classes upon its removal. This is informational. cce "show cce cpdp associations " "class-group " CCE_PI_PD-6-TARGET_BINDINGS_DB 6-Information [chars] [chars] [chars] target class group %08X contains feature bindings The target class group is reporting the presence of feature bindings upon its removal. This is informational. cce "show cce cpdp bindings " "target " CCE_PI_PD-6-TARGET_BINDINGS_DB 6-Information [chars] [chars] [chars] target class group %08X contains feature bindings The target class group is reporting the presence of feature bindings upon its removal. This is informational. cce "show cce cpdp bindings " "target " CCE-3-CCE_IPV6_COMPR_CLASSIFY_FAIL 3-Error Dataplane IPV6 compression classification error for interface [chars] Cisco internal software error. The dataplane was unable to complete processing of an IPV6 prefix classification request due to a miss on a TCAM lookup. This is likely due to a data initialization error cpp-ucode keyword:cce LOG_STD_ACTION CCE-3-CCE_NON_TCAM_CLASSIFY 3-Error Dataplane classification error for interface [chars] Cisco internal software error. The dataplane was unable to complete processing of a classification request because an invalid form of classification was selected. This is likely due to a data initialization error cpp-ucode keyword:cce LOG_STD_ACTION CCE-3-HW_CCE_TCAM_CONFIG 3-Error Control Plane classification config error: TCAM device not specified: MPLS or Layer2 [chars] [chars] Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error qfp-infra-internal keyword:cce LOG_STD_ACTION CCE-3-HW_CCE_TCAM_CONFIG_IPV4 3-Error Control Plane classification config error: TCAM device not specified: [chars] [chars] Ipv4 src %Ci dst %Ci Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error qfp-infra-internal keyword:cce LOG_STD_ACTION CCE-3-HW_CCE_TCAM_CONFIG_IPV6 3-Error Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6 src [ipv6_addr] dst [ipv6_addr] Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error qfp-infra-internal keyword:cce LOG_STD_ACTION CCE-3-HW_CCE_TCAM_CONFIG_IPV6_COMPR 3-Error Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6 compression src [ipv6_addr] dst [ipv6_addr] Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error qfp-infra-internal keyword:cce LOG_STD_ACTION CCE-3-HW_CCE_TCAM_CONFIG_IPV6_EXT 3-Error Control Plane classification config error: TCAM device not specified: [chars] [chars] IPv6_ext src [ipv6_addr] dst [ipv6_addr] Cisco internal software error. The dataplane was unable to complete processing of a classification request because the TCAM device was not specified. This is likely due to a data initialization error qfp-infra-internal keyword:cce LOG_STD_ACTION CCE-3-HW_TCAM_CONTROLLER 3-Error Datapath classification program flow error: invalid TCAM controller 0x%lx Cisco internal software error. The dataplane detected a classification request providing an invalid TCAM controller value. The program flow Traceback qfp-infra-internal keyword:cce LOG_STD_ACTION CCH323-2-E164_LENGTH_IS_NOT_SUPPORTED 2-Critical [chars]: E164 address length [dec] is not supported Received E164 address with the length that is not supported. ios-voice "Report this immediately to the technical support representative." CCH323-2-E164_LENGTH_IS_NOT_SUPPORTED 2-Critical [chars]: E164 address length [dec] is not supported Received E164 address with the length that is not supported. ios-voice "Report this immediately to the technical support representative." CCH323-2-GTKP_UNREGSTR 2-Critical Gatekeeper [chars] requested unregister from Gateway [chars] Gatekeeper requested unregister from Gateway ios-voice "Verify whether this is user intended or otherwise report this to the\n\ technical support representative." CCH323-2-GTKP_UNREGSTR 2-Critical Gatekeeper [chars] requested unregister from Gateway [chars] Gatekeeper requested unregister from Gateway ios-voice "Verify whether this is user intended or otherwise report this to the\n\ technical support representative." CCH323-2-GTWY_REGSTR_FAILED 2-Critical Gateway [chars] failed to register with Gatekeeper [chars] even after [dec] retries Gateway failed to register with Gatekeeper ios-voice "Report this immediately to the technical support representative." CCH323-2-GTWY_REGSTR_FAILED 2-Critical Gateway [chars] failed to register with Gatekeeper [chars] even after [dec] retries Gateway failed to register with Gatekeeper ios-voice "Report this immediately to the technical support representative." CCH323-2-GTWY_REGSTR_FAILED_ALT_GK 2-Critical Gateway [chars] failed attempt to register with Alternate Gatekeeper [chars] Gateway failed attempt to register with Alternate Gatekeeper ios-voice "Report this immediately to the technical support representative." CCH323-2-GTWY_REGSTR_FAILED_ALT_GK 2-Critical Gateway [chars] failed attempt to register with Alternate Gatekeeper [chars] Gateway failed attempt to register with Alternate Gatekeeper ios-voice "Report this immediately to the technical support representative." CCH323-2-GTWY_UNREGSTR 2-Critical Gateway [chars] unregistered from Gatekeeper [chars] Gateway unregistered from the Gatekeeper ios-voice "Verify whether this is user intended or otherwise report this to the\n\ technical support representative." CCH323-2-GTWY_UNREGSTR 2-Critical Gateway [chars] unregistered from Gatekeeper [chars] Gateway unregistered from the Gatekeeper ios-voice "Verify whether this is user intended or otherwise report this to the\n\ technical support representative." CCH323-3-BAD_IP_ADDRESS 3-Error [chars]: illegal destination [chars] The IP address passed from CCAPI in the call setup request is invalid ios-voice "Check the dial-peer configuration for the dial-peer that matches the\n\ called party number. Make sure that the session target field contains\n\ valid IP address. or DNS name" CCH323-3-BAD_IP_ADDRESS 3-Error [chars]: illegal destination [chars] The IP address passed from CCAPI in the call setup request is invalid ios-voice "Check the dial-peer configuration for the dial-peer that matches the\n\ called party number. Make sure that the session target field contains\n\ valid IP address. or DNS name" CCH323-3-CALL_SETUP_FAILED 3-Error [chars]: call setup failed The call setup request failed ios-voice "Verify that the remote destination identified by the IP address is reachable" CCH323-3-CALL_SETUP_FAILED 3-Error [chars]: call setup failed The call setup request failed ios-voice "Verify that the remote destination identified by the IP address is reachable" CCH323-3-CANNOT_ALLOCATE_CALL_INFO 3-Error [chars]: cannot allocate call info data structure Allocation of the CCH323 call info structure failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This call will be terminated due to lack of resource" CCH323-3-CANNOT_ALLOCATE_CALL_INFO 3-Error [chars]: cannot allocate call info data structure Allocation of the CCH323 call info structure failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This call will be terminated due to lack of resource" CCH323-3-CANNOT_ALLOCATE_CCB 3-Error [chars]: cannot allocate call control block Allocation of the CCH323 call control block failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This can be a catastrophic error" CCH323-3-CANNOT_ALLOCATE_CCB 3-Error [chars]: cannot allocate call control block Allocation of the CCH323 call control block failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This can be a catastrophic error" CCH323-3-CANNOT_ALLOCATE_GW 3-Error [chars]: cannot allocate gateway structure Allocation of the CCH323 gateway instance failed. This is possibly due\n\ to the fact that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_ALLOCATE_GW 3-Error [chars]: cannot allocate gateway structure Allocation of the CCH323 gateway instance failed. This is possibly due\n\ to the fact that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_CREATE_CCB 3-Error [chars]: cannot create the H.323 ccb Tree Creation of the H.323 CCB Tree failed. This is possibly due to the fact \n\ that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_CREATE_CCB 3-Error [chars]: cannot create the H.323 ccb Tree Creation of the H.323 CCB Tree failed. This is possibly due to the fact \n\ that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_CREATE_CRVHASH_TBL 3-Error [chars]: cannot create the H.323 crv hash table Creation of the H.323 CRV Hash Table failed. This is possibly due to \n\ the fact that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_CREATE_CRVHASH_TBL 3-Error [chars]: cannot create the H.323 crv hash table Creation of the H.323 CRV Hash Table failed. This is possibly due to \n\ the fact that system memory pool is exhausted. voice-h323 "This can be a catastrophic error" CCH323-3-CANNOT_FIND_CCB 3-Error [chars]: cannot find CCH323 call control block based on callID [dec] Cannot find a CCH323 call control block based on the specified callID ios-voice "No action is required. This is an indication that some events happen\n\ out of sequence" CCH323-3-CANNOT_FIND_CCB 3-Error [chars]: cannot find CCH323 call control block based on callID [dec] Cannot find a CCH323 call control block based on the specified callID ios-voice "No action is required. This is an indication that some events happen\n\ out of sequence" CCH323-3-CANNOT_INSERT_CCB 3-Error [chars]: cannot insert control block 0x[hec] to tree Insertion of this CCH323 call control block to the RBTree failed. This\n\ can be related to a corrupted RBTree ios-voice "This can be a catastrophic error" CCH323-3-CANNOT_INSERT_CCB 3-Error [chars]: cannot insert control block 0x[hec] to tree Insertion of this CCH323 call control block to the RBTree failed. This\n\ can be related to a corrupted RBTree ios-voice "This can be a catastrophic error" CCH323-3-CCAPI_CONNECT_ERROR 3-Error [chars]: cc_api_call_disconnected returns [dec] An error is returned when CCH323 attempts to call cc_api_call_connected ios-voice "None" CCH323-3-CCAPI_CONNECT_ERROR 3-Error [chars]: cc_api_call_disconnected returns [dec] An error is returned when CCH323 attempts to call cc_api_call_connected ios-voice "None" CCH323-3-CCAPI_DISCONNECT_ERROR 3-Error [chars]: cc_api_call_disconnected returns [dec] An error is returned when CCH323 attempts to call cc_api_call_disconnected ios-voice "None" CCH323-3-CCAPI_DISCONNECT_ERROR 3-Error [chars]: cc_api_call_disconnected returns [dec] An error is returned when CCH323 attempts to call cc_api_call_disconnected ios-voice "None" CCH323-3-CCH323_H225_SEND_EVENT_FAILED 3-Error [chars]: create send internal event [chars] to H.225 state machine failed create and send event to H.225 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_H225_SEND_EVENT_FAILED 3-Error [chars]: create send internal event [chars] to H.225 state machine failed create and send event to H.225 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_H245_SEND_EVENT_FAILED 3-Error [chars]: create and send event [chars] to H.245 state machine failed create and send event to H.245 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_H245_SEND_EVENT_FAILED 3-Error [chars]: create and send event [chars] to H.245 state machine failed create and send event to H.245 state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_MALLOC_FAILED 3-Error [chars]: cannot allocate message buffer Allocation of the CCH323 message buffer failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This can be a catastrophic error" CCH323-3-CCH323_MALLOC_FAILED 3-Error [chars]: cannot allocate message buffer Allocation of the CCH323 message buffer failed. This is possibly due\n\ to the fact that system memory pool is exhausted. ios-voice "This can be a catastrophic error" CCH323-3-CCH323_RAS_SEND_EVENT_FAILED 3-Error [chars]: create and send event [chars] to RAS state machine failed create and send event to RAS state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_RAS_SEND_EVENT_FAILED 3-Error [chars]: create and send event [chars] to RAS state machine failed create and send event to RAS state machine failed. This is possibly due\n\ to the missing call control block or not enough memory for event buffers ios-voice "This can be a catastrophic error" CCH323-3-CCH323_RSCMON_SETUP_FAILURE 3-Error [chars][dec] A failure was encountered in setting up the monitoring of\n\ H323 resources. ios-voice "Try power cycling the system. " LOG_STD_RECUR_ACTION CCH323-3-CCH323_RSCMON_SETUP_FAILURE 3-Error [chars][dec] A failure was encountered in setting up the monitoring of\n\ H323 resources. ios-voice "Try power cycling the system. " LOG_STD_RECUR_ACTION CCH323-3-CCH323_UNKNOWN_EVENT 3-Error unknown event [hec] Unknown CCH323 Event ios-voice "No action is required" CCH323-3-CCH323_UNKNOWN_EVENT 3-Error unknown event [hec] Unknown CCH323 Event ios-voice "No action is required" CCH323-3-H225_LIBRARY_INIT_FAILED 3-Error [chars]: H.225.0 library initialization failed H.225.0 library initialization failed ios-voice "This can be catastrophic" CCH323-3-H225_LIBRARY_INIT_FAILED 3-Error [chars]: H.225.0 library initialization failed H.225.0 library initialization failed ios-voice "This can be catastrophic" CCH323-3-H225_SM_INIT_FAILED 3-Error [chars]: H.225.0 State Machine integrity check failed for state [chars] H.225 State Machine integrity check failed ios-voice "This can be catastrophic" CCH323-3-H225_SM_INIT_FAILED 3-Error [chars]: H.225.0 State Machine integrity check failed for state [chars] H.225 State Machine integrity check failed ios-voice "This can be catastrophic" CCH323-3-INTERNAL_EVENT_QUEUE_INIT_FAILED 3-Error [chars]: Internal event queue initialization failed Errors are found during initialization of internal event qeuue machanisa ios-voice "This can be a catastrophic error" CCH323-3-INTERNAL_EVENT_QUEUE_INIT_FAILED 3-Error [chars]: Internal event queue initialization failed Errors are found during initialization of internal event qeuue machanisa ios-voice "This can be a catastrophic error" CCH323-3-MAXIMUM_INTERNAL_EVENT_BUFFERS_EXCEED 3-Error [chars]: Exceeding limit on allocating internal event buffers The limit for allocating internal event buffers has been exceeded.\n\ The condition may be caused by internal loops on\n\ sending events between state machines. - "This can be a severe error" CCH323-3-MAXIMUM_INTERNAL_EVENT_BUFFERS_EXCEED 3-Error [chars]: Exceeding limit on allocating internal event buffers The limit for allocating internal event buffers has been exceeded.\n\ The condition may be caused by internal loops on\n\ sending events between state machines. - "This can be a severe error" CCH323-3-OSS_INIT_FAILED 3-Error [chars]: OSS init failure: errno = [dec] OSS ASN1 initialization failed ios-voice "This can be catastrophic" CCH323-3-OSS_INIT_FAILED 3-Error [chars]: OSS init failure: errno = [dec] OSS ASN1 initialization failed ios-voice "This can be catastrophic" CCH323-3-POSSIBLE_INTERNAL_EVENT_LOOP 3-Error [chars]: Exceeding limit on servicing internal event for the same call The maximum limit on servicing internal event queue has exceeded\n\ the limit. The condition may be caused by internal loops on\n\ sending events between state machines. ios-voice "This can be a severe error" CCH323-3-POSSIBLE_INTERNAL_EVENT_LOOP 3-Error [chars]: Exceeding limit on servicing internal event for the same call The maximum limit on servicing internal event queue has exceeded\n\ the limit. The condition may be caused by internal loops on\n\ sending events between state machines. ios-voice "This can be a severe error" CCH323-3-STRCALLHISFAIL 3-Error \ncch323_store_call_history: [chars] Insert an active H323 call record into call history list failed ios-voice "No action is required" CCH323-3-STRCALLHISFAIL 3-Error \ncch323_store_call_history: [chars] Insert an active H323 call record into call history list failed ios-voice "No action is required" CCH323-6-CALL_PRESERVED 6-Information [chars]: H.323 call preserved due to socket closure or error Call Id = [dec] fd = [dec] An H.225.0 or H.245 socket was closed due to a TCP FIN received from the remote endpoint or a socket error. Calls using these sockets for which call preservation was configured will be preserved. This is not an error but call preservation can occasionally cause hung calls. voice-h323 "Use \"show h323 calls preserved\" command to get a " "list of all active preserved calls. Long duration preserved calls can " "then be cleared using \"clear call voice\" command." CCH323-6-CALL_PRESERVED 6-Information [chars]: H.323 call preserved due to socket closure or error Call Id = [dec] fd = [dec] An H.225.0 or H.245 socket was closed due to a TCP FIN received from the remote endpoint or a socket error. Calls using these sockets for which call preservation was configured will be preserved. This is not an error but call preservation can occasionally cause hung calls. voice-h323 "Use \"show h323 calls preserved\" command to get a " "list of all active preserved calls. Long duration preserved calls can " "then be cleared using \"clear call voice\" command." CCH323-6-LONG_DUR_CALL_DETECTED 6-Information Long Duration Call is detected [chars]\n The call is active for configured duration of long call ios-voice LOG_STD_ACTION CCH323-6-LONG_DUR_CALL_DETECTED 6-Information Long Duration Call is detected [chars]\n The call is active for configured duration of long call ios-voice LOG_STD_ACTION CCH323-6-REGSTR 6-Information Gateway [chars] registered with Gatekeeper [chars] Gateway registered with the Gatekeeper none "no action is required" CCH323-6-REGSTR 6-Information Gateway [chars] registered with Gatekeeper [chars] Gateway registered with the Gatekeeper none "no action is required" CCK_QAT-3-INIT_FAIL 3-Error [chars]: initialization failed [chars] CCK QAT initialization sequence failed. iosxe-ipsec "Copy the error message exactly as it appears and report it to your \n\ technical support representative." CCM-3-CCMINVALEVT 3-Error Client[[dec]] received an invalid event[[dec]] Cluster Control Manager High Availability feature on standby detected an invalid event received from active ccm LOG_STD_ACTION CCM-3-CCMINVALEVT 3-Error Client[[dec]] received an invalid event[[dec]] Cluster Control Manager High Availability feature on standby detected an invalid event received from active ccm LOG_STD_ACTION CCM-3-CCMINVALEVT 3-Error - An error occurred during initialization SISF_COMP_NAME LOG_STD_ACTION CCM-3-CCMINVALEVT 3-Error - An internal software error occurred. SISF_COMP_NAME LOG_STD_ACTION CCM-3-CCMINVALEVT 3-Error - A PSS operation was performed SISF_COMP_NAME "This is an informationnal message" CCM-3-CCMINVALEVT 3-Error - An entry was created in the binding table SISF_COMP_NAME "This is an informationnal message" CCM-3-CCMINVALEVT 3-Error - An entry was created in the binding table SISF_COMP_NAME "This is an informationnal message" CCM-3-CCMINVALEVT 3-Error - An entry was changed in the binding table SISF_COMP_NAME "This is an informationnal message" CCM-3-CCMINVALEVT 3-Error - Reached 80% of maximum # addresses for the target SISF_COMP_NAME "A client is approaching red zone and might soon \n\ be blocked. The maximum value configured may be too low \n\ and you should consider increasing it. Or some of this client addresses are \n\ stale and you could clear them" CCM-3-CCMINVALEVT 3-Error - An attempt to install an entry in the binding table was blocked. This can be due to a conflicting entry or maximum number of entries reached SISF_COMP_NAME "If the maximum table size is reached consider increasing it.\n\ If a conflicting entry already exist this maybe an attempt \n\ to steal address ownership. You should investigate which host\n\ is connected on the interface and wether it should be disconnected" CCM-3-CCMINVALEVT 3-Error - A duplicate IP address has been detected IP theft and blocked This can be due to a configuration error on end-device an intentional IP theft or an IP movind too quickly sisf "If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved" CCM-3-CCMINVALEVT 3-Error - A duplicate MAC address has been detected MAC theft and blocked This can be due to a configuration error on end-device an intentional MAC theft or MAC moving too quickly SISF_COMP_NAME "If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved" CCM-3-CCMINVALEVT 3-Error - A duplicate MAC and IP address has been detected MAC_AND_IP theft and blocked This can be due to a configuration error on end-device an intentional MAC_AND_IP theft or MAC moving too quickly SISF_COMP_NAME "If the existing entry is REACHABLE in the binding table and it moved to a new port \n\ consider reducing the REACHABLE timer \n\ otherwise it is either an attack or a configuration issue that must be resolved" CCM-3-CCMINVALEVT 3-Error - - - - CCM-3-CCMNOCLIENT 3-Error Client [chars][[dec]] not present Cluster Control Manager High Availability features for this client will not work. ccm "Refer to the documentation on configuring High Availability features" CCM-3-CCMNOCLIENT 3-Error Client [chars][[dec]] not present Cluster Control Manager High Availability features for this client will not work. ccm "Refer to the documentation on configuring High Availability features" CCM-3-CCMREGFAIL 3-Error High Availability Registration failed Cluster Control Manager High Availability features will not work. ccm LOG_STD_ACTION CCM-3-CCMREGFAIL 3-Error High Availability Registration failed Cluster Control Manager High Availability features will not work. ccm LOG_STD_ACTION CCPROXY-3-NO_CONNECT_TABLE 3-Error \ Unable to allocate memory for [dec] connection table entries in [chars].\n - - - CCPROXY-3-NO_CONNECT_TABLE 3-Error \ Unable to allocate memory for [dec] connection table entries in [chars].\n - - - CCPROXY-3-NO_RASREQ_TABLE 3-Error \ Unable to allocate memory for [dec] RAS request table entries in [chars].\n - - - CCPROXY-3-NO_RASREQ_TABLE 3-Error \ Unable to allocate memory for [dec] RAS request table entries in [chars].\n - - - CCPROXY-3-NOBLOCK_EVENT 3-Error \ During initialization of proxy [chars]: cannot allocate event block\n - - - CCPROXY-3-NOBLOCK_EVENT 3-Error \ During initialization of proxy [chars]: cannot allocate event block\n - - - CCPROXY-3-NOCALL_ccIFInService 3-Error \ No proxy CCAPI interface found: H.323 proxy bringup failed in [chars].\n - - - CCPROXY-3-NOCALL_ccIFInService 3-Error \ No proxy CCAPI interface found: H.323 proxy bringup failed in [chars].\n - - - CCPROXY-3-NOCCAPI_INTERFACE 3-Error \ CCAPI new interface is not created in [chars]\n - - - CCPROXY-3-NOCCAPI_INTERFACE 3-Error \ CCAPI new interface is not created in [chars]\n - - - CCPROXY-3-NOCCB_FROM_CALLID 3-Error \ No call-control-block is found in [chars] for [hec].\n - - - CCPROXY-3-NOCCB_FROM_CALLID 3-Error \ No call-control-block is found in [chars] for [hec].\n - - - CCPROXY-3-NOINIT_OSS_h225 3-Error \ [chars]: initializing h225 socket failed through ASN.1 library: error=[dec]\n - - - CCPROXY-3-NOINIT_OSS_h225 3-Error \ [chars]: initializing h225 socket failed through ASN.1 library: error=[dec]\n - - - CCPROXY-3-NOINIT_OSS_h245 3-Error \ [chars]: initializing h245 socket failed through ASN.1 library: error=[dec]\n - - - CCPROXY-3-NOINIT_OSS_h245 3-Error \ [chars]: initializing h245 socket failed through ASN.1 library: error=[dec]\n - - - CCPROXY-3-NOMEMORY_FRAGMENT_CACHE 3-Error \ [chars]: failed to allocate cache for fragmented packets for fastswitch - - - CCPROXY-3-NOMEMORY_FRAGMENT_CACHE 3-Error \ [chars]: failed to allocate cache for fragmented packets for fastswitch - - - CCPROXY-3-NOMM_INTERFACE 3-Error \ No multimedia interface configured in [chars].\n - - - CCPROXY-3-NOMM_INTERFACE 3-Error \ No multimedia interface configured in [chars].\n - - - CCPROXY-3-NOPROCESS_CCPROXY 3-Error \ The proxy process is not created in [chars]\n - - - CCPROXY-3-NOPROCESS_CCPROXY 3-Error \ The proxy process is not created in [chars]\n - - - CCPROXY-3-STRCALLHISFAIL 3-Error [chars]: Unable to store Call History record - - - CCPROXY-3-STRCALLHISFAIL 3-Error [chars]: Unable to store Call History record - - - CCPROXY-3-UNREGISTERED_BY_GK 3-Error \ H.323 Proxy registration is being removed by Gatekeeper [chars]\n Check \show proxy h323 status\ for details. - - - CCPROXY-3-UNREGISTERED_BY_GK 3-Error \ H.323 Proxy registration is being removed by Gatekeeper [chars]\n Check \show proxy h323 status\ for details. - - - CD_FFP_IPSEC_PROXY-2-FFP_INIT_FAILED 2-Critical FFP Crypto device Proxy Agent initialization failure result: [dec]. Cisco internal software error. FFP Crypto device Procy Agent initialization detected critical failure. FFP Crypto device software library will not be functional while this condition exists. ffp-ipsec keyword:datapath LOG_STD_ACTION CD_FFP_IPSEC_PROXY-2-FFP_PROXY_INIT_FAILED 2-Critical FFP Crypto device Procy Agent Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. FFP Crypto device Procy Agent Proxy initialization detected that the IPC interface initialization failed. FFP Crypto device Procy Agent proxy will not be functional while this conidtion exists. ffp-ipsec keyword:datapath LOG_STD_ACTION CD_FFP_IPSEC_PROXY-3-ESG_IPSEC_KAT_TEST_FAILED 3-Error Cryptographic Known-Answer Test failure result: [chars] Cisco internal software error. Cryptographic Known-Answer Tests. Error due to one of the Cryptographic Power-on Self-tests Known-Answer Tests not returning the expected value. esg-ipsec keyword:datapath LOG_STD_ACTION CD_FFP_IPSEC_PROXY-3-FFP_PROXY_IPSEC_SA_CRT_FAILED 3-Error FFP Crypto device Procy Agent Proxy IPSec SA create failure result: [dec]. Cisco internal software error. FFP Crypto device Procy Agent Proxy message processing detected IPSec SA create failure. The request is rejected as the result of this condition. ffp-ipsec keyword:datapath LOG_STD_ACTION CD_SW_IPSEC_SHIM-2-KAT_TEST_FAILED 2-Critical QFP Crypto device software library kat test failure result: [dec]. Cisco internal software error. QFP Crypto device software library detected critical failure. QFP Crypto device software library will not be functional while this condition exists. ultra-ipsec keyword:datapath LOG_STD_ACTION CD_SW_IPSEC_SHIM-2-SHIM_INIT_FAILED 2-Critical QFP Crypto device software library initialization failure result: [dec]. Cisco internal software error. QFP Crypto device software library initialization detected critical failure. QFP Crypto device software library will not be functional while this condition exists. ultra-ipsec keyword:datapath LOG_STD_ACTION CD_SW_IPSEC_SHIM-2-SHIM_PROXY_INIT_FAILED 2-Critical QFP Crypto device software library Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP Crypto device software library Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device software library proxy will not be functional while this conidtion exists. ultra-ipsec keyword:datapath LOG_STD_ACTION CD_SW_IPSEC_SHIM-3-SHIM_PROXY_IPSEC_SA_CRT_FAILED 3-Error QFP Crypto device software library Proxy IPSec SA create failure result: [dec]. Cisco internal software error. QFP Crypto device software library Proxy message processing detected IPSec SA create failure. The request is rejected as the result of this condition. ultra-ipsec keyword:datapath LOG_STD_ACTION CD_SW_SSL_SHIM-2-SHIM_INIT_FAILED 2-Critical QFP Crypto device software library initialization failure result: [dec]. Cisco internal software error. QFP Crypto device software library initialization detected critical failure. QFP Crypto device software library will not be functional while this condition exists. ultra-ssl keyword:datapath LOG_STD_ACTION CD_SW_SSL_SHIM-2-SHIM_PROXY_INIT_FAILED 2-Critical QFP Crypto device software library Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP Crypto device software library Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device software library proxy will not be functional while this conidtion exists. ultra-ssl keyword:datapath LOG_STD_ACTION CD_SW_SSL_SHIM-3-SHIM_PROXY_SSL_CTX_ALLOC_FAILED 3-Error QFP Crypto device software library Proxy IPSec CTX create failure result: [dec]. Cisco internal software error. QFP Crypto device software library Proxy message processing detected IPSec CTX create failure. The request is rejected as the result of this condition. ultra-ssl keyword:datapath LOG_STD_ACTION CDP_PD-2-POWER_LOW 2-Critical [chars] - [chars] [chars] [enet] on port [chars] System is not supplied with its maximum power - "Reconfigure or replace the source of inline power to get maximum power." CDP_PD-4-POWER_OK 4-Warning [chars] - [chars] inline power source on port [chars] System is supplied with sufficient power. - "No recommended action." CDP-3-CHUNK 3-Error Chunk_malloc Failure chunk malloc failure cdp LOG_STD_ACTION CDP-3-CHUNK 3-Error Chunk_malloc Failure chunk malloc failure cdp LOG_STD_ACTION CDP-4-DUPLEX_MISMATCH 4-Warning duplex mismatch discovered on [chars] [chars] with [chars] [chars] [chars]. CDP discovered a mismatch of duplex configuration - "Configure the interfaces to the same duplex full or half." CDP-4-DUPLEX_MISMATCH 4-Warning duplex mismatch discovered on [chars] [chars] with [chars] [chars] [chars]. CDP discovered a mismatch of duplex configuration - "Configure the interfaces to the same duplex full or half." CDP-4-NATIVE_VLAN_MISMATCH 4-Warning Native VLAN mismatch discovered on [chars] [dec] with [chars] [chars] [dec]. CDP discovered a mismatch of native-VLAN configuration - "Configure the interfaces to the same native VLAN." CDP-4-NATIVE_VLAN_MISMATCH 4-Warning Native VLAN mismatch discovered on [chars] [dec] with [chars] [chars] [dec]. CDP discovered a mismatch of native-VLAN configuration - "Configure the interfaces to the same native VLAN." CDP-6-TLV_LIST_GLOBALLY 6-Information Tlv-list [chars] [chars] globally on all interfaces. CDP Tlv-list configuration Globally. - "No action required. The message is informatory in nature." CDP-6-TLV_LIST_GLOBALLY 6-Information Tlv-list [chars] [chars] globally on all interfaces. CDP Tlv-list configuration Globally. - "No action required. The message is informatory in nature." CDP-6-TLV_LIST_INTERFACE 6-Information Tlv-list [chars] [chars] interface [chars] An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." CDP-6-TLV_LIST_INTERFACE 6-Information Tlv-list [chars] [chars] interface [chars] The get_fd function reported an error trying to allocate a Event Detector context control block. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." CEF_PROXY-3-PROXY_IPC_ADJ_ID_HASH_FAILED 3-Error - Getting Hash Address failed. cpp-ucode LOG_STD_ACTION CEF_PROXY-3-PROXY_IPC_ADJ_IDX_FAILED 3-Error [hec] Failed to get adjacency index from IPC packet. cpp-ucode LOG_STD_ACTION CEF_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION CEF_PROXY-3-PROXY_IPC_OCE_CHAIN_PTR_FAILED 3-Error [hec] Null OCE Chain pointer. cpp-ucode LOG_STD_ACTION CEF_PROXY-3-PROXY_IPC_PACKET_ALLOCATION_FAILED 3-Error [hec] Failed to allocate packet buffer for IPC cpp-ucode LOG_STD_ACTION CEF_PROXY-3-PROXY_IPC_PACKET_SEND_FAILED 3-Error [hec] Failed to send IPC packet. cpp-ucode LOG_STD_ACTION CEF_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION CEF_SHIM_FIB-3-FIBTOPO 3-Error Error for topology [dec]: [chars] CEF_SHIM_FIB_INTERNAL_ERROR CEF_SHIM_DDTS_COMPONENT LOG_STD_ACTION CEF-3-CYLON_CEF_MAX_VRF_EXCEEDED 3-Error Number of VRF instances already exceeded allowed limit [dec] Number of vrf instances exceeded supported platform scale firmware "Please reduce the number of vrf instances" "to scale to platform supported scale" CEF-3-KBP_PREFIX_IP_MPLS_LIMIT_EXCEEDED 3-Error Number of ip mpls Prefixes exceeded allowed limit [dec] on asic [dec] Number of ip mpls Prefixes exceeded supported scale rsp3-infra "Please reduce the number of ip mpls Prefixes" "to scale to platform supported scale" CEF-3-KBP_PREFIX_IP_MPLS_LIMIT_EXCEEDED 3-Error Number of ip mpls Prefixes exceeded allowed limit [dec] on asic [dec] Number of ip mpls Prefixes exceeded supported scale dominica-infra "Please reduce the number of ip mpls Prefixes" "to scale to platform supported scale" CEF-3-KBP_PREFIX_IPV6_LIMIT_EXCEEDED 3-Error Number of ipv6 Prefixes exceeded allowed limit [dec] on asic [dec] Number of ipv6 Prefixes exceeded supported scale rsp3-infra "Please reduce the number of ipv6 Prefixes" "to scale to platform supported scale" CEF-3-KBP_PREFIX_IPV6_LIMIT_EXCEEDED 3-Error Number of ipv6 Prefixes exceeded allowed limit [dec] on asic [dec] Number of ipv6 Prefixes exceeded supported scale dominica-infra "Please reduce the number of ipv6 Prefixes" "to scale to platform supported scale" CEF-3-NILE_CEF_MAX_VRF_EXCEEDED 3-Error Number of VRF instances already exceeded allowed limit [dec] Number of vrf instances exceeded supported platform scale firmware "Please reduce the number of vrf instances" "to scale to platform supported scale" CEF-3-NILE_CEF_MAX_VRF_EXCEEDED 3-Error Number of VRF instances exceeded allowed limit [dec] Number of vrf instances exceeded supported platform scale firmware "Please reduce the number of vrf instances" "to scale to platform supported scale" CEF-3-NILE_CEF_MAX_VRF_EXCEEDED 3-Error Number of VRF instances exceeded allowed limit [dec] Number of vrf instances exceeded supported platform scale firmware "Please reduce the number of vrf instances" "to scale to platform supported scale" CELLWAN-1-POOL_INIT_FAIL 1-Alert cellular pool init failed for subslot [dec]/[dec] \ pool name [chars] The NIM cellular pool init failed for this module. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-BEARER_CONGESTION_OFF 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is NOT congested now Traffic congestion has cleared in the dedicated bearer - "No action is needed" CELLWAN-2-BEARER_CONGESTION_ON 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is congested Traffic congestion present in the dedicated bearer. If it does not clear make sure the host QOS configuration matches the dedicated bearer configuration - "Check the MBR of the dedicated bearer by doing show " "cellular and configure the host QOS configuration " "to match MBR of the dedicated bearer." CELLWAN-2-BEARER_DELETED 2-Critical [chars] bearer bearer_id=[dec] in [chars] is now deleted. default/dedicated bearer has been deleted. - "Host QOS configuration may need to be deleted" " to match the modem configuration" CELLWAN-2-BEARER_DOWN 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is now down. default/dedicated bearer has been deleted. - "Host QOS configuration may need to be modified" " to match the modem configuration" CELLWAN-2-BEARER_MODIFIED 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] configuration in [chars] is modified default/dedicated bearer configuration has been modified. - "Check the TFT rules of the dedicated bearer by doing" " show cellular and configure the host QOS" " configuration to match the TFT rules" CELLWAN-2-BEARER_SUSPENDED 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] default/dedicated bearer has been suspended. - "Host QOS configuration may need to be suspended" " to match the modem configuration" CELLWAN-2-BEARER_UP 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] in [chars] is now UP default/dedicated bearer has been added. - "Check the TFT rules of the dedicated bearer by doing show cellular" " and configure the host QOS configuration to match the TFT rules" CELLWAN-2-CALL_SETUP_FAIL 2-Critical [chars] data call setup failed due to [chars]. Data call setup failed because the IP address configured under cellular interface does not match the IP address assigned by the network esg-lte "Please check the IP address configuration under cellular" "interface" CELLWAN-2-CRASHDUMP_SUCCESS 2-Critical [chars]:Crashdump successfully logged in /bootflash/ Cellular Modem Crashdump files successfully logged to local flash. esg-lte "" CELLWAN-2-DEDICATED_BEARER_STATUS_UNKNOWN 2-Critical Instance id=[dec] [chars] bearer bearer_id=[dec] QCI=[dec] configuration in [chars] is Dedicated bearer configuration status is unknown. - "Check the TFT rules of the dedicated bearer by doing" " show cellular and report the TFT rules to the " "carrier." CELLWAN-2-DMLOG_FILTER_FILE_OPEN_ERROR 2-Critical [chars] failed to open [chars] to read DM log filter. Failed to open filter file from the location configured with 'gsm|cdma|lte modem dm-log filter' under cellular controller esg-lte "Please check that the path configured under cellular " "controller is reachable" CELLWAN-2-DMLOG_OUTPUT_FILE_OPEN_ERROR 2-Critical [chars] failed to open [chars] to archive DM log files. Saving DM packets to file system failed. Output file URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller can not be opened esg-lte "Please check that the path configured under cellular " "controller is reachable" CELLWAN-2-DMLOG_OUTPUT_SPACE_FULL 2-Critical [chars] DM log file storage is full! Saving DM packets to file system failed because there is no more space left on the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller esg-lte "Please delete existing log files from the specified URL " "'gsm|cdma|lte modem dm-log output path' or upload them " "to the server then re-enable logging." CELLWAN-2-DMLOG_OUTPUT_WRITE_ERROR 2-Critical [chars] failed to write [chars] DM packets to configured file system Saving DM packets to file system failed because of write error to the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller esg-lte "Please check that the URL configured under cellular " "controller with 'gsm|cdma|lte modem dm-log output path' " "is reachable and has enough storage space" CELLWAN-2-DYING_GASP_NOT_SUPPORTED 2-Critical Dying Gasp Feature is not supported in Cellular slot [dec]/[dec] This NIM is not supporting Dying Gasp Feature. esg-lte "Please contact TAC for Dying Gasp Feature Supported NIM" CELLWAN-2-DYING_GASP_POWER_FAILURE 2-Critical Dying Gasp SMS will not be sent out by Modem in slot [dec]/[dec] due to standby power failure. Please contact TAC. Modem doesn't have enough power to send Dying Gasp SMS esg-lte "Please contact TAC" CELLWAN-2-DYING_GASP_POWER_SUCCESS 2-Critical Modem in slot [dec]/[dec] has sufficient power to send Dying Gasp SMS Modem has sufficient power to send Dying Gasp SMS esg-lte "No action is needed" CELLWAN-2-GSM_PROFILE_UNDEFINED 2-Critical [[chars]]: Default profile [dec][chars] does not exist. Please execute 'cellular gsm profile create ' to create the profile. Default profile is undefined. the profile does not exist because it is not defined or is deleted. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-HEART_BEAT_TIMEOUT 2-Critical No heart beat signal from [chars] The cellular modem is not responding. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-INTERFACE_GOING_DOWN 2-Critical [chars] is being shutdown temporarily due to authentication failure for [dec] secs. The interface is being shutdown because the call could not be connected due to PPP authentication failures. The interface will be brought up after the specified time. This is to prevent frequent calls being attempted if authentication problems are not fixed. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-LINK_RECOVERY 2-Critical [chars]: Cellular Modem has been power cycled : [chars] Link Recovery Process has detected an inconsistent state of the modem - "" CELLWAN-2-MDM_LINK_FAILURE 2-Critical [chars] direct IP synchronization process fails after [dec] attempts Direct IP synchronization fails to come up after maximum number of attempts. esg-lte "Contact customer service if the problem persists." CELLWAN-2-MICRO_DNLD_END_FAIL 2-Critical \nModem returned following error to Download End Request:[chars] Modem Firmware Download End Request Failed esg-lte "show flash: command " "and show controller cellular x/x/x all" CELLWAN-2-MICRO_DNLD_START_FAIL 2-Critical \nModem returned following error to Download Start Request:[chars] Modem Firmware Download Start Request Failed. It generally means that firmware binary file is wrong. esg-lte "show flash: command " "and show controller cellular x/x/x all" CELLWAN-2-MICRO_FLASH_PRGM_FAIL 2-Critical \nModem returned following error to Flash Program Request:[chars] Modem failed to launch the new firmware. esg-lte "show flash: command " "and show controller cellular x/x/x all" CELLWAN-2-MICRO_FW_DNLD_FAIL 2-Critical \nModem returned following error to Download Request:[chars] Modem Firmware Download Continue Request Failed. It generally means that firmware binary file is corrupt. esg-lte "show flash: command " "and show controller cellular x/x/x all" CELLWAN-2-MODEM_DOWN 2-Critical Modem in slot [dec]/[dec] is DOWN The cellular modem is not operational. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-MODEM_INIT_TIMEOUT 2-Critical Cellular modem initialization timeout for [chars] Modem failed to initialize. esg-lte LOG_STD_SH_TECH_ACTION CELLWAN-2-MODEM_NOT_ACTIVATED 2-Critical [chars] modem has not been activated The cellular modem has not been activated by the cellular provider. esg-lte "Please check the user documentation on how to activate the modem. " "The cellular modem needs to be activated before it can be used on " "a cellular network." CELLWAN-2-MODEM_RADIO 2-Critical [chars] Modem radio has been turned [chars] Modem radio has been turned on/off. esg-lte "show cellular x/x/x radio command " "and show tech-support" CELLWAN-2-MODEM_TIMEOUT 2-Critical Modem in [chars] not responding The cellular modem is not responding. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-MODEM_TOO_HOT 2-Critical [chars] modem will be [chars] Modem radio temperature has reached critical point. The call will be disconnected and the modem could be shutdown. esg-lte "Check if the router fans are working properly." CELLWAN-2-MODEM_UP 2-Critical Modem in slot [dec]/[dec] is now UP The cellular modem is now UP. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-NC_EVENT1 2-Critical [chars]: Network change event - fallback from ENDC to LTE. Modem fallback from ENDC to LTE esg-lte "No action" CELLWAN-2-NC_EVENT2 2-Critical [chars]: Network change event - activated 4G Carrier Aggregation. Modem activated 4G Carrier Aggregation esg-lte "No action" CELLWAN-2-NC_EVENT3 2-Critical [chars]: Network change event - activated 5G ENDC. Modem activated 5G ENDC esg-lte "No action" CELLWAN-2-NO_PROCESS 2-Critical Could not start process [chars] Could not start one of the processes. esg-lte "Add more memory." CELLWAN-2-OMA_DM_ACTIVE 2-Critical [[chars]]: OMA DM [chars] session is active OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_ERROR 2-Critical [[chars]]: OMA DM [chars] Failed - Error:0x[hec][chars] OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_HFA_PENDING 2-Critical [[chars]]: OMA DM [chars] waiting for retry in [dec] seconds OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_NI_ALERT 2-Critical [[chars]]: OMA DM NI Alert is received for [chars] \nPlease execute 'cellular cdma activate oma-dm ni-alert [allow | deny]' OMA DM Network-Initiated alert is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_NO_OP 2-Critical [[chars]]: OMA DM [chars] could not be completed. \nPlease try again later. If the problem persists you may need to contact Customer Service. OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_NO_PRL 2-Critical [[chars]]: OMA DM - No PRL update available OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-OMA_DM_SUCCESS 2-Critical [[chars]]: OMA DM [chars] completed successfully OMA DM session state is received by modem esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-POWER_SAVE_MODE 2-Critical [[chars]]: is in Power save mode. Command ignored. radio is currently OFF on this NIM esg-lte LOG_STD_ACTION CELLWAN-2-QOS_ENABLED 2-Critical QoS Feature in [chars] is now activated QoS Feature is now enabled and activated in the modem. - "QoS Feature is now enabled and activated in the modem." CELLWAN-2-QOS_NW_STATUS 2-Critical Network status for QoS feature is [chars] in [chars]. Network status for QoS feature is either enabled or disabled by the carrier. - "check with carrier if you expect QoS feature but it is disabled" CELLWAN-2-QOS_PRI_EVENT_STATUS 2-Critical QoS Event Status = [dec] for default bearer in [chars] in [chars]. QoS Event Status for default bearer for the cellular interface. - "check with carrier to see if the default bearer" " config is changed" CELLWAN-2-SEND_TIMEOUT 2-Critical [chars] not responding The cellular modem is not responding. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_CHV1_BLOCKED 2-Critical [[chars]]: SIM is blocked. PUK is required to unblock the SIM [chars] SIM is blocked and no data call can be made until it is unblocked using PUK. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_CHV1_CONFIG_REMOVED 2-Critical [[chars]]: CHV1 verfication failed [chars] : Incorrect PIN configured. Erased the CHV1 code from router runnning configuration to avoid SIM blocking during modem reset/powercycle. \n!!!WARNING: If the incorrect PIN is saved in router start-up configuration please remove it manually to avoid SIM blocking during router reload SIM CHV1 verfication failed. Incorrect PIN configured. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_FAILURE 2-Critical [[chars]]: SIM read failed [chars] If the SIM is not present insert SIM in the SIM socket. If error still persists SIM needs to be replaced. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_LOCKED 2-Critical [[chars]]: SIM is locked [chars] SIM is locked and no data call can be made till it is unlocked. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_MEP_LOCKED 2-Critical [[chars]]: Invalid SIM or device locked to carrier [chars] Invalid SIM or device locked to carrier esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_NOT_PRESENT 2-Critical [[chars]]: SIM is not present in Slot [dec] SIM has not been detected in the NIM SIM socket esg-lte "Insert a valid sim in the NIM SIM socket." CELLWAN-2-SIM_NOT_READY 2-Critical [chars] Modem is not ready. SIM status may be not current. SIM access cannot be granted or may return an error when : 1 The modem is not up or during a reset. esg-lte "1 Wait till MODEM UP message is seen from the console before accessing SIM." CELLWAN-2-SIM_REJECTED 2-Critical [[chars]]: SIM rejected by the network [chars] The SIM is not valid to be used in the network. A new valid SIM needs to be inserted in the SIM socket. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_SECURITY_SHUTDOWN 2-Critical [[chars]]: CHV1 PIN is configured while SIM is unlocked [chars]. Shutting down all PDP interfaces CHV1 is configured while SIM is unlocked The SIM is not valid to be used in the network. A new valid locked SIM needs to be inserted in the SIM socket. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-2-SIM_SWITCH_FAILURE 2-Critical [[chars]]: Failed to switch to SIM slot [dec] !! Failed to switch to the requested NIM SIM slot esg-lte "Examine SIM in the indicated slot" CELLWAN-2-SMS_ARCH_PATH_UNCONFIGURED 2-Critical [chars] failed to archive SMS because 'gsm|cdma|lte sms archive path' under cellular controller is not configured. 'gsm|cdma|lte sms archive path' under cellular controller must be configured first before background incoming text message archive can function properly esg-lte "Configure 'gsm|cdma|lte sms archive path' under cellular controller" CELLWAN-2-SMS_INBOX_ARCH_OPEN_ERROR 2-Critical [chars] failed to open [chars] to archive incoming SMS. Incoming text messages archive to FTP server failed because the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller can not be opened esg-lte "Please check that the FTP server configured under cellular " "controller is reachable and that the directory exists" CELLWAN-2-SMS_INBOX_ARCH_WRITE_ERROR 2-Critical [chars] failed to write [chars] to archive incoming SMS. Incoming text messages archive to FTP server failed because of write error to the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller esg-lte "Please check that the FTP server configured under cellular " "controller with 'gsm|cdma|lte sms archive path' is reachable and " "has enough storage space" CELLWAN-2-SMS_OUTBOX_ARCH_OPEN_ERROR 2-Critical [chars] failed to open [chars] to archive an outgoing SMS. Outgoing text message archive to FTP server failed because the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller can not be opened esg-lte "Please check that the FTP server configured under cellular " "controller is reachable and that the directory exists" CELLWAN-2-SMS_OUTBOX_ARCH_WRITE_ERROR 2-Critical [chars] failed to write [chars] to archive an outgoing SMS. Outgoing text message archive to FTP server failed because of write error to the FTP URL configured with 'gsm|cdma|lte sms archive path' under cellular controller esg-lte "Please check that the FTP server configured under cellular " "controller with 'gsm|cdma|lte sms archive path' is reachable and " "has enough storage space" CELLWAN-2-SVBLOG_OUTPUT_FILE_OPEN_ERROR 2-Critical [chars] failed to open [chars] to archive SVB log files. Saving SVB packets to file system failed. Output file URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller can not be opened esg-lte "Please check that the path configured under cellular " "controller is reachable" CELLWAN-2-SVBLOG_OUTPUT_SPACE_FULL 2-Critical [chars] SVB log file storage is full! Saving SVB packets to file system failed because there is no more space left on the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller esg-lte "Please delete existing log files from the specified URL " "'gsm|cdma|lte modem dm-log output path' or upload them " "to the server then re-enable logging." CELLWAN-2-SVBLOG_OUTPUT_WRITE_ERROR 2-Critical [chars] failed to write [chars] SVB packets to configured file system Saving SVB packets to file system failed because of write error to the URL configured with 'gsm|cdma|lte modem dm-log output path' under cellular controller esg-lte "Please check that the URL configured under cellular " "controller with 'gsm|cdma|lte modem dm-log output path' " "is reachable and has enough storage space" CELLWAN-2-UNSUPPORTED_CELLULAR_NIM 2-Critical Unsupported Cellular NIM inserted in slot [dec]/[dec] This NIM is not supported for the current software release esg-lte "Please contact TAC for supported software release for this NIM" CELLWAN-2-WCDMA_ALL_BAND_UNDEFINED 2-Critical [[chars]]: wcdma-all band not supported wcdma-all band is not supported by modem or not defined esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-3-GPS_FAIL_END_SESSION 3-Error [[chars]] GPS failed to end location fix session - [chars] [0x[hec]] please try again Modem failed to disable GPS mode due to error indicated. Fix that error and try again. esg-lte "Fix error indicated and try disabling GPS again." CELLWAN-3-GPS_FAIL_START_TRACK 3-Error [[chars]] GPS failed to start tracking - [chars] [0x[hec]] please try again Modem failed to enable GPS mode due to error indicated. Fix that error and try again. esg-lte "Fix error indicated and try enabling GPS again." CELLWAN-3-GSM_PROFILE_CREATION_FAILURE 3-Error [[chars]] GSM profile creation fails - [chars] [0x[hec]] please try again Modem failed to create the GSM profile due to error indicated. Fix that error and try again. esg-lte "Fix error indicated and try creating GSM profile again." CELLWAN-4-CELLULAR_FW_UNSUPPORTED 4-Warning [chars]: Unsupported or older modem firmware [chars] detected please upgrade modem to supported firmware of at least [chars] The current firmware on specified cellular interface is not supported. Any actions and errors that occur will not be supported until the fw is upgraded to at least the version requested esg-lte "Please upgrade to the latest FW from online using" " 'microcode reload'" CELLWAN-4-CELLULAR_MODEM_SKU_MISMATCH 4-Warning [chars]: Mismatch detected between installed modem [chars][SKU ID [chars]] on SKU type [chars]. Expected modem for this SKU is [chars][SKU ID [chars]] Incorrect modem type has been installed on this SKU. Any actions and issues caused by it will not be supported esg-lte "Please contact the cisco customer service" "to replace the card" CELLWAN-4-DG_DETACH_CONFIG_FAILED 4-Warning Dying Gasp Detach Configuration Failed. [chars] Dying Gasp Detach Configuration Failed. - "Please try Dying Gasp Detach Configuration later" CELLWAN-4-DG_SMS_CONFIG_FAILED 4-Warning Dying Gasp SMS Configuration Failed. [chars] Dying Gasp SMS Configuration Failed. - "Please try Dying Gasp SMS Configuration later" CELLWAN-4-MANUAL_PLMN_SELECTION_FAILED 4-Warning Manual/Force PLMN Selection Failed. [chars] Manual/Force PLMN Selection Failed - "Please use Different PLMN or check number of MNC Bits " "in PLMN Selection" CELLWAN-4-MODEM_COMM_FAIL 4-Warning Communication between Modem and IOS failed: [chars] Communication between Modem and IOS Failed - " Modem Reset will recover " CELLWAN-4-MODEM_RESTART_IND 4-Warning [chars] Modem restart [chars] Modem Restart Indication - "No action is needed" CELLWAN-4-OUTGOING_SMS_ERROR 4-Warning [chars] failed to send an outgoing SMS. Outgoing text message failed to send from cellular interface esg-lte "Please do 'show cellular sms' to see " "error code" CELLWAN-4-OUTGOING_SMS_SERV_UNAVAIL 4-Warning [chars] can't send an SMS because SMS service is not available. Text message service is not available on specified cellular interface esg-lte "Check modem is powered up radio is not in power " "saving mode and SIM is inserted" CELLWAN-5-DMLOG_AUTOSTOP_TIMER_CANCEL 5-Notice [chars]: DM logging autostop timer canceled DM logging autostop timer is canceled esg-lte LOG_STD_NO_ACTION CELLWAN-5-DMLOG_AUTOSTOP_TIMER_EXPIRY 5-Notice [chars]: DM logging stopped DM logging is stopped due to autostop trigger timer expiry esg-lte LOG_STD_NO_ACTION CELLWAN-5-DMLOG_AUTOSTOP_TRIGGER 5-Notice [chars]: DM logging will be stopped in [dec] [chars] autostop trigger event [chars] set DM log autostop trigger event configured DM logging will be stopped after the timer expiry esg-lte LOG_STD_NO_ACTION CELLWAN-5-DMLOG_DISABLE_OIR 5-Notice [chars]: OIR Detected. DM logging stopped DM logging is stopped due to OIR esg-lte LOG_STD_NO_ACTION CELLWAN-5-DMLOG_DISPLAY_OUTPUT_PATH_EXTERN 5-Notice DM log output path = bootflash:/core/modules DM log output path set to bootflash:/core/modules esg-lte "" CELLWAN-5-DMLOG_DISPLAY_OUTPUT_PATH_INTEGRATED 5-Notice DM log output path = bootflash: DM log output path set to bootflash:/ esg-lte "" CELLWAN-5-FIRMWARE_SWITCH 5-Notice Firmware switchover initiated for modem in slot [dec]/[dec] Firmware switchover caused by user request. esg-lte LOG_STD_NO_ACTION CELLWAN-5-INCOMING_SMS 5-Notice [chars] has just received new incoming SMS. New incoming text messages arrived at cellular interface esg-lte "Please do 'cellular gsm|cdma sms view' to read SMS" CELLWAN-5-MNO_SWITCH 5-Notice MNO switchover initiated for modem in slot [dec]/[dec] MNO switchover caused by user request. esg-lte LOG_STD_NO_ACTION CELLWAN-5-MODEM_BOOT_READY 5-Notice Modem in slot [dec]/[dec] is in Boot Ready Mode.. Please perform FW upgrade The cellular modem is not operational. esg-lte "show cellular x/x/x all command " "and show tech-support" CELLWAN-5-NULL_BEARER 5-Notice NULL Bearer Timer [chars]:Current NULL Bearer count:[dec]:Total NULL Bearer count:[dec]:Profile id:[dec]:PDN ID:[dec] NULL Bearer notification from modem. No action is required esg-lte LOG_STD_NO_ACTION CELLWAN-5-OUTGOING_SMS_SENT 5-Notice [chars] has just sent an outgoing SMS successfully. Outgoing text message was sent successfully from cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_ACQUISITION_TIMEOUT 5-Notice [[chars]]: SIM slot [dec] Acquisition Timer timeout !! Timeout on the SIM slot acquisition timer initiate sim switching request to the alter SIM slot esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_ACTIVATION 5-Notice [[chars]]: SIM slot [dec] is being activated !! The request to activate the indicated SIM slot has been sent to the modem esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_ACTIVATION_TIMEOUT 5-Notice [[chars]]: SIM slot [dec] activation request timeout !! Timeout on the request sent to the modem to activate the indicated SIM slot esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_ACTIVE 5-Notice [[chars]]: SIM slot [dec] is Active !! The indicated SIM slot is active. esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_DETECT_COMPLETE 5-Notice [[chars]]: SIM presence detection has completed !! SIM presence detection has completed esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_DETECT_START 5-Notice [[chars]]: SIM presence detection starts !! SIM presence detection has started esg-lte LOG_STD_NO_ACTION CELLWAN-5-SIM_FAILOVER_TIMEOUT 5-Notice [[chars]]: SIM slot [dec] Failover Timer timeout !! Timeout on the SIM slot failover timer initiate sim switching request to the alter SIM slot esg-lte LOG_STD_NO_ACTION CELLWAN-5-SMS_INBOX_ARCH_DONE 5-Notice [chars] has just archived all incoming SMS to FTP server successfully. Incoming text messages were archived to FTP server successfully from cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SMS_INBOX_MSG_ARCH_DONE 5-Notice [chars] has just archived an incoming SMS to FTP server successfully. An incoming text message was archived to FTP server successfully from cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SMS_OUTBOX_ARCH_DONE 5-Notice [chars] has just archived an outgoing SMS to FTP server successfully. An outgoing text message was archived to FTP server successfully from cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SMS_SERVICE_AVAILABLE 5-Notice [chars] SMS service is now available. You can send and receive text messages on this cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SMS_SERVICE_UNAVAILABLE 5-Notice [chars] SMS service is now unavailable. You can not send and receive text messages on this cellular interface esg-lte LOG_STD_NO_ACTION CELLWAN-5-SVBLOG_AUTOSTOP_TIMER_CANCEL 5-Notice [chars]: SVB logging autostop timer canceled SVB logging autostop timer is canceled esg-lte LOG_STD_NO_ACTION CELLWAN-5-SVBLOG_AUTOSTOP_TIMER_EXPIRY 5-Notice [chars]: SVB logging stopped SVB logging is stopped due to autostop trigger timer expiry esg-lte LOG_STD_NO_ACTION CELLWAN-5-SVBLOG_AUTOSTOP_TRIGGER 5-Notice [chars]: SVB logging will be stopped in [dec] minutes autostop trigger event [chars] set SVB log autostop trigger event configured SVB logging will be stopped after the timer expiry esg-lte LOG_STD_NO_ACTION CELLWAN-6-CELLULAR_BACKOFF_START 6-Information [chars]: Cellular back-off has started on PDN [dec] Back off has started because of certain error codes from network side - "" CELLWAN-6-CELLULAR_BACKOFF_STOP 6-Information [chars]: Cellular back-off has stopped on PDN [dec] Back off has stopped - "" CELLWAN-6-CELLULAR_NETWORK_ATTACH_FAILURE 6-Information [chars]: Cellualr network attachment failure. Reject Cause [dec] [chars]. Network attachment failure - "Check 3GPP Table 10.5.95/3GPP TS 24.008 for information" CELLWAN-6-FOTA_DNLD_COMPLETE 6-Information [[chars]]: Firmware has been downloaded for modem in cellular slot [dec]/[dec] FOTA Cellular modem firmware download started. esg-lte "" CELLWAN-6-FOTA_DNLD_STARTED 6-Information [[chars]]: Firmware download started in cellular slot [dec]/[dec] FOTA Cellular modem firmware download started. esg-lte "" CELLWAN-6-FOTA_UPGRADE_STARTED 6-Information [[chars]]: Firmware upgrade started in cellular slot [dec]/[dec]. Modem will reset and come up with new firmware. FOTA Cellular modem firmware upgraded started. esg-lte "" CELLWAN-6-FOTA_UPGRADE_SUCESS 6-Information [[chars]]: Firmware upgrade successful in cellular slot [dec]/[dec] FOTA Cellular modem firmware upgraded successfully. esg-lte "" CELLWAN-6-FOTA_UPGRADE_TIMEOUT 6-Information [[chars]]: Firmware upgrade timed out in cellular slot [dec]/[dec] FOTA Cellular modem firmware upgrade timed out. esg-lte "" CELLWAN-6-SIM_INSERTED 6-Information [[chars]]: SIM in slot [dec] has been \n\ inserted SIM is inserted to the slot. esg-lte "No action" CELLWAN-6-SIM_PRESENT 6-Information [[chars]]: SIM is present in Slot [dec] SIM has been detected in the SIM socket esg-lte "No action" CELLWAN-6-SIM_REMOVED 6-Information [[chars]]: WARNING: SIM in slot [dec] has \n\ been removed SIM is removed from the slot. esg-lte "No action" CEM-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. cemcommon "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." CEM-3-ISSU_SENDFAILED 3-Error \nCEM ISSU: send message failed rc = [dec]\n The sending of a message has failed. cemcommon LOG_STD_SH_TECH_ACTION CEM-4-DEJITTER_CAS_UNSUPPORTED 4-Warning Interface [chars]: [dec] With CAS enabled in LOTR-IM\n With CAS enabled in LOTR-IM Configured De-jitter will be ignored and Calculated De-jitter based on the configured payload is used cemcommon "This is an informational message only. No action is required" CEM-4-ISSU_INCOMPATIBLE 4-Warning \ncem-issu-compat: returned FALSE The compatibility checking has failed cemcommon LOG_STD_SH_TECH_ACTION CEM-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The transform has failed. cemcommon LOG_STD_SH_TECH_ACTION CEMA-3-ATM_VC_CONFIG_FAIL 3-Error [chars]: connection configuration failed for VC [dec]/[dec] [chars] A failure occurred when sending a VC configuration command. - CEMA_CMD_FAIL_ACTION CEMA-3-ATM_VP_CONFIG_FAIL 3-Error [chars]: connection configuration failed for VP [dec] [chars] A failure occurred when sending a VP configuration command. - CEMA_CMD_FAIL_ACTION CEMA-3-CARD_TYPE_CONFIG_FAIL 3-Error [chars]: card type configuration failed [chars] A failure occurred when sending a card type configuration command. - CEMA_CMD_FAIL_ACTION CEMA-3-CEMA_ADD_FAIL 3-Error [chars]: CEMA SB addition failed for interface [chars] A failure occurred when adding cema_sb to the interface shown in the error message. - SPA_CEMA_FAIL_ACTION CEMA-3-CLEAR_CONNECTION_STATS_FAIL 3-Error [chars]: clear connection stats failed [chars] A failure occurred when sending a clear connection stats command. - CEMA_CMD_FAIL_ACTION CEMA-3-CLEAR_INTERFACE_STATS_FAIL 3-Error [chars]: clear interface stats failed [chars] A failure occurred when sending a clear interface stats command. - CEMA_CMD_FAIL_ACTION CEMA-3-CONNECTION_DELETE_FAIL 3-Error [chars]: connection delete failed [chars] A failure occurred when sending a connection delete command. - CEMA_CMD_FAIL_ACTION CEMA-3-INTERFACE_CONFIG_FAIL 3-Error [chars]: interface configuration failed [chars] A failure occurred when sending an interface delete command. - CEMA_CMD_FAIL_ACTION CEMA-3-INTERFACE_DELETE_FAIL 3-Error [chars]: interface delete failed [chars] A failure occurred when sending an interface delete command. - CEMA_CMD_FAIL_ACTION CEMOUDP_NP_CLIENT-3-INFO 3-Error [chars] CEMOUDP NP Client failed to initialize properly which will result in\n\ improper operation of cemoudp feature vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." CEMOUDP_NP_CLIENT-3-NOMEM 3-Error [chars] CEMOUDP NP Client failed to initialize properly which will result in\n\ improper operation of cemoudp feature vsp-mid "This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." CEMOUDP_NP_CLIENT-4-WARN 4-Warning [chars] [dec] [chars] CEMOUDP Entry could not be added because:\n\ 1. Entry passed is invalid. vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." CENT-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the CENT feature failed. This will cause the feature to not function. qfp-cent "This is normally a software issue. " "The consequences are that the CENT feature will not function. " LOG_STD_ACTION CENT-3-CENT_RC_AT_FO_OVERWRITE 3-Error FO overwritten detected: magic [hec] table_id [hec] next_hop [hec] Cisco internal software error. The dataplane was unable to complete enqueuing a packet. This is likely due to a data initialization error cpp-ucode keyword:cent LOG_STD_ACTION CENT-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper CENT software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-cent "This is normally a software issue. " LOG_STD_RECUR_ACTION CENT-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper CENT software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-cent "This is normally a software issue. " LOG_STD_RECUR_ACTION CERF-2-ABORT 2-Critical [chars] This message is emitted when a cache error has occured but an attempt\n\ to recover has been aborted - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CERF-3-RECOVER 3-Error [chars] This message is emitted when there has been a full recovery after a\n\ cache error - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CERM_DP-4-DP_RX_BW_LIMIT 4-Warning Maximum Rx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license. Maximum Rx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license. esg-ipsec "Obtain 'hseck9' feature license and install it." CERM_DP-4-DP_TX_BW_LIMIT 4-Warning Maximum Tx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license. Maximum Tx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license. esg-ipsec "Obtain 'hseck9' feature license and install it." CERM_DP-4-SSLVPN_DP_RX_BW_LIMIT 4-Warning Maximum TLS Rx Bandwidth limit of [dec] Kbps reached. Maximum TLS Rx Bandwidth limit reached for Crypto functionality. qfp-sslvpn "" CERM_DP-4-SSLVPN_DP_TX_BW_LIMIT 4-Warning Maximum TLS Tx Bandwidth limit of [dec] Kbps reached. Maximum TLS Tx Bandwidth limit reached for Crypto functionality. qfp-sslvpn "" CERM-4-RX_BW_LIMIT 4-Warning Maximum Rx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license. Maximum Rx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license. c2900 "Obtain 'hseck9' feature license and install it." CERM-4-TLS_SESSION_LIMIT 4-Warning Maximum TLS session limit of [dec] reached for Crypto functionality with \ securityk9 technology package license. Maximum TLS session limit reached for Crypto functionality with \ securityk9 technology package license. c2900 "Obtain 'hseck9' feature license and install it." CERM-4-TUNNEL_LIMIT 4-Warning Maximum tunnel limit of [dec] reached for Crypto functionality with \ securityk9 technology package license. Maximum tunnel limit reached for Crypto functionality with securityk9 \ technology package license. c2900 "Obtain 'hseck9' feature license and install it." CERM-4-TX_BW_LIMIT 4-Warning Maximum Tx Bandwidth limit of [dec] Kbps reached for Crypto functionality \ with securityk9 technology package license. Maximum Tx Bandwidth limit reached for Crypto functionality with \ securityk9 technology package license. c2900 "Obtain 'hseck9' feature license and install it." CES-2-INTERNAL_CRITICAL 2-Critical [chars] The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION CES-3-INTERNAL_ERROR 3-Error [chars] The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION CES-4-INTERNAL_WARNING 4-Warning [chars] The CES subsystem encountered an internal software error. The error message contains text which can be used to help identify the nature of the problem. - LOG_STD_SH_TECH_ACTION CF_REGISTER_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - CF_REGISTER_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - CFC_LISP-3-ADJ 3-Error Request to [chars] adjacency [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ADJ 3-Error Request to [chars] adjacency [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ADJ_SEQ 3-Error Adjacency [chars] is still complete after interface shutdown An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ADJ_SEQ 3-Error Adjacency [chars] is still complete after interface shutdown An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ALLOCATEFAIL 3-Error Failed to allocate memory for [chars] An internal software error occurred. This is probably because not enough memory was available. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ALLOCATEFAIL 3-Error Failed to allocate memory for [chars] An internal software error occurred. This is probably because not enough memory was available. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-BG_PROCESS 3-Error Background process failed to [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-BG_PROCESS 3-Error Background process failed to [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DECAP_OCE 3-Error Failed to [chars] LISP decapsulation OCE: [chars][chars] An operation dealing with a LISP decapsulation OCE encountered an error. The error message will indicate which operation failed and the address-family context. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DECAP_OCE 3-Error Failed to [chars] LISP decapsulation OCE: [chars][chars] An operation dealing with a LISP decapsulation OCE encountered an error. The error message will indicate which operation failed and the address-family context. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DEP_ELEM 3-Error Request to [chars] dependency [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DEP_ELEM 3-Error Request to [chars] dependency [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DEPRECATED_API 3-Error Use of a deprecated API [chars][chars] - CFC_LISP_MSG_DDTS_COMP "Increase the MTU of the path to the remote RLOC" CFC_LISP-3-DEPRECATED_API 3-Error Use of a deprecated API [chars][chars] - CFC_LISP_MSG_DDTS_COMP "Increase the MTU of the path to the remote RLOC" CFC_LISP-3-DYN_EID_IP_ADDR_CONFLICT 3-Error Ignore dynamic EID detection due to IP Address conflict [chars]:[chars] on [chars] A dynamic EID Host attempted to register with an IP address conflicting with the XTR gateway. Refer to error message log for more details. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-DYN_EID_IP_ADDR_CONFLICT 3-Error Ignore dynamic EID detection due to IP Address conflict [chars]:[chars] on [chars] A dynamic EID Host attempted to register with an IP address conflicting with the XTR gateway. Refer to error message log for more details. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ELIG_OCE 3-Error Failed to [chars] LISP eligibility oce [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ELIG_OCE 3-Error Failed to [chars] LISP eligibility oce [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-FREE_WITH_DEPS 3-Error Request to remove dependency sb on [chars] with dependents An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-FREE_WITH_DEPS 3-Error Request to remove dependency sb on [chars] with dependents An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-GSMR 3-Error Failed to [chars] generalised SMR attribute for [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-GSMR 3-Error Failed to [chars] generalised SMR attribute for [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-INVALID_INPUT 3-Error Invalid input [chars] to [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-INVALID_INPUT 3-Error Invalid input [chars] to [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-IPL_SRC 3-Error Failed to [chars] IPL source [chars] [chars]/[dec][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-IPL_SRC 3-Error Failed to [chars] IPL source [chars] [chars]/[dec][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ISSU_NEGO_ERR 3-Error Failed to negotiate [chars] for XDR client [chars] error [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ISSU_NEGO_ERR 3-Error Failed to negotiate [chars] for XDR client [chars] error [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ISSU_REG_ERR 3-Error Failed to register [chars] for ISSU client [chars] [dec] entity [dec] error [chars] - - - CFC_LISP-3-ISSU_REG_ERR 3-Error Failed to register [chars] for ISSU client [chars] [dec] entity [dec] error [chars] - - - CFC_LISP-3-ISSU_XFORM_ERR 3-Error Failed to ISSU transform XDR message [chars] error [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-ISSU_XFORM_ERR 3-Error Failed to ISSU transform XDR message [chars] error [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-LOCAL_EID 3-Error Failed to [chars] local EID prefix [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-LOCAL_EID 3-Error Failed to [chars] local EID prefix [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_ADJ 3-Error Failed to find adjacency for [chars] [chars] [chars] [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_ADJ 3-Error Failed to find adjacency for [chars] [chars] [chars] [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_FIBIDB 3-Error Failed to find fibidb for [chars] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_FIBIDB 3-Error Failed to find fibidb for [chars] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_PATH 3-Error Failed to resolve path type for [chars]:[chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_PATH 3-Error Failed to resolve path type for [chars]:[chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_SB 3-Error Failed to find subblock for [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_SB 3-Error Failed to find subblock for [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_TABLE 3-Error Failed to find table for [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_TABLE 3-Error Failed to find table for [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_VIF 3-Error Unable to find [chars]virtual interface [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-NO_VIF 3-Error Unable to find [chars]virtual interface [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-PUSH_CNTR 3-Error Failed to [chars] push counter for [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-PUSH_CNTR 3-Error Failed to [chars] push counter for [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-REMOTE_EID 3-Error Failed to [chars] remote EID prefix [chars]/[dec][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-REMOTE_EID 3-Error Failed to [chars] remote EID prefix [chars]/[dec][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-REMOTE_EID_PREFIX 3-Error Failed to [chars] remote EID prefix [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-REMOTE_EID_PREFIX 3-Error Failed to [chars] remote EID prefix [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-RLOC_VRF_IN_USE 3-Error RLOC vrfid [dec] already in use by user [chars] top-id [dec] cannot assign to top-id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-RLOC_VRF_IN_USE 3-Error RLOC vrfid [dec] already in use by user [chars] top-id [dec] cannot assign to top-id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SB_OPERATION_FAILED 3-Error Failed to [chars] subblock on [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SB_OPERATION_FAILED 3-Error Failed to [chars] subblock on [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SIGNAL_OCE 3-Error Failed to [chars] LISP signal OCE [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SIGNAL_OCE 3-Error Failed to [chars] LISP signal OCE [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SRC_RLOC_IDX 3-Error [chars] source RLOC index database[chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-SRC_RLOC_IDX 3-Error [chars] source RLOC index database[chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_BIND 3-Error Error setting [chars] table [chars] for top-id [dec] iid [dec] [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_BIND 3-Error Error setting [chars] table [chars] for top-id [dec] iid [dec] [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_CONFLICT 3-Error Conflicting LISP config for top-id [dec] iid [dec] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_CONFLICT 3-Error Conflicting LISP config for top-id [dec] iid [dec] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_STATE 3-Error Error setting state for table [chars] to top-id [dec] iid [dec] role [chars] [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TABLE_STATE 3-Error Error setting state for table [chars] to top-id [dec] iid [dec] role [chars] [chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TERM_ADJ 3-Error Terminal adjacency [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TERM_ADJ 3-Error Terminal adjacency [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TIMESTAMP_CTRL_PKT 3-Error Failed to timestamp LISP control packet An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TIMESTAMP_CTRL_PKT 3-Error Failed to timestamp LISP control packet An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_EID_ALT_FIBIDB 3-Error Tree [chars] failed for [chars] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_EID_ALT_FIBIDB 3-Error Tree [chars] failed for [chars] [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_IID 3-Error Tree [chars] failed for iid [dec] under top_id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_IID 3-Error Tree [chars] failed for iid [dec] under top_id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_L2_DOMAIN 3-Error Tree [chars] failed for L2 Domain ID [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_L2_DOMAIN 3-Error Tree [chars] failed for L2 Domain ID [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_TOP 3-Error Tree [chars] failed for top_id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-TREE_OP_FAIL_TOP 3-Error Tree [chars] failed for top_id [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNABLE_TO_IDENTIFY_TABLE 3-Error Unable to identify table for packet from [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNABLE_TO_IDENTIFY_TABLE 3-Error Unable to identify table for packet from [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNEXPECTED_PATH 3-Error Unexpected path type [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNEXPECTED_PATH 3-Error Unexpected path type [chars]/[dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNEXPECTED_PKT 3-Error [chars]: 0x%08x A packet with an unexpected protocol was given to the LISP datapath. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNEXPECTED_PKT 3-Error [chars]: 0x%08x A packet with an unexpected protocol was given to the LISP datapath. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNKN_INSTANCE 3-Error Unknown instance unable to find/create virtual interface An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNKN_INSTANCE 3-Error Unknown instance unable to find/create virtual interface An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNKNOWN_PAYLOAD 3-Error Dropping LISP encapsulated packet unknown payload 0x%08x An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-UNKNOWN_PAYLOAD 3-Error Dropping LISP encapsulated packet unknown payload 0x%08x An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-VIF 3-Error Unable to [chars] virtual interface [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-VIF 3-Error Unable to [chars] virtual interface [chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-WALK_DEP 3-Error Walking dependents [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-WALK_DEP 3-Error Walking dependents [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-XDR_LEN_ERR 3-Error Failed to [chars] XDR message [chars] len [dec] > max [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-XDR_LEN_ERR 3-Error Failed to [chars] XDR message [chars] len [dec] > max [dec] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-3-XDR_REG_ERR 3-Error Failed to register XDR client [chars] [dec] error [chars] - - - CFC_LISP-3-XDR_REG_ERR 3-Error Failed to register XDR client [chars] [dec] error [chars] - - - CFC_LISP-5-ADJ_STACK 5-Notice Stacking adjacency [chars] [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-5-ADJ_STACK 5-Notice Stacking adjacency [chars] [chars][chars][chars] An internal software error occurred. CFC_LISP_MSG_DDTS_COMP LOG_STD_ACTION CFC_LISP-5-BELOW_MIN_MTU 5-Notice Cannot set [chars] MTU for RLOC [chars] to [dec] [chars] MTU for [chars] [chars] is [dec] below minimum MTU [dec]+[dec] required for LISP encap Unable to set the EID payload MTU for a remote RLOC below the minimal MTU this will cause the encapsulated packet to be bigger than the MTU of the path to the remote RLOC and may cause packet loss. CFC_LISP_MSG_DDTS_COMP "Increase the MTU of the path to the remote RLOC" CFC_LISP-5-BELOW_MIN_MTU 5-Notice Cannot set [chars] MTU for RLOC [chars] to [dec] [chars] MTU for [chars] [chars] is [dec] below minimum MTU [dec]+[dec] required for LISP encap Unable to set the EID payload MTU for a remote RLOC below the minimal MTU this will cause the encapsulated packet to be bigger than the MTU of the path to the remote RLOC and may cause packet loss. CFC_LISP_MSG_DDTS_COMP "Increase the MTU of the path to the remote RLOC" CFC_LISP-5-IGNOREICMPMTU 5-Notice Ignoring received ICMP Type 3 Code 4 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting An ICMP Type 3 Code 4 fragmentation needed and DF set packet CFC_LISP_MSG_DDTS_COMP "If you want the ICMP packet to be accepted and used " "use the ip lisp pmtu min NUMBER max NUMBER " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed." CFC_LISP-5-IGNOREICMPMTU 5-Notice Ignoring received ICMP Type 3 Code 4 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting An ICMP Type 3 Code 4 fragmentation needed and DF set packet CFC_LISP_MSG_DDTS_COMP "If you want the ICMP packet to be accepted and used " "use the ip lisp pmtu min NUMBER max NUMBER " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed." CFC_LISP-5-IGNOREICMPV6MTU 5-Notice Ignoring received ICMPv6 Type 2 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting An ICMPv6 Type 2 Packet Too Big packet CFC_LISP_MSG_DDTS_COMP "If you want the ICMP packet to be accepted and used " "use the ipv6 lisp pmtu min NUMBER max NUMBER " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed." CFC_LISP-5-IGNOREICMPV6MTU 5-Notice Ignoring received ICMPv6 Type 2 [chars]->[chars] next hop mtu [dec] due to pmtu min or max setting An ICMPv6 Type 2 Packet Too Big packet CFC_LISP_MSG_DDTS_COMP "If you want the ICMP packet to be accepted and used " "use the ipv6 lisp pmtu min NUMBER max NUMBER " "command to decrease the minimum MTU allowed and/or increase the " "maximum MTU that is allowed." CFC_MPLS_CP_APP_MSG-3-CLIENT_ERR 3-Error MPLS CP APP Unsupported Client [dec] Unsupported client trying to use cfc apis mpls-mfi LOG_STD_ACTION CFC_MPLS_CP_APP_MSG-3-CLIENT_ERR 3-Error MPLS CP APP Unsupported Client [dec] Unsupported client trying to use cfc apis mpls-mfi LOG_STD_ACTION CFC_MPLS_CP_ION-3-BATCHERR 3-Error MPLS CP ION Batch Error [dec] for [chars] Error in batching ion messages between cfc and mpls clients mpls-mfi LOG_STD_ACTION CFC_MPLS_CP_ION-3-BATCHERR 3-Error MPLS CP ION Batch Error [dec] for [chars] Error in batching ion messages between cfc and mpls clients mpls-mfi LOG_STD_ACTION CFC_SRV6-3-DISPATCH_OCE 3-Error Failed to [chars] SRv6 dispath oce [chars][chars] - - - CFC_SRV6-3-DISPATCH_OCE 3-Error Failed to [chars] SRv6 dispath oce [chars][chars] - - - CFC_SRV6-3-END_OCE 3-Error Failed to [chars] SRv6 end oce [chars][chars] An internal software error occurred. CFC_SRV6_MSG_DDTS_COMP LOG_STD_ACTION CFC_SRV6-3-END_OCE 3-Error Failed to [chars] SRv6 end oce [chars][chars] An internal software error occurred. CFC_SRV6_MSG_DDTS_COMP LOG_STD_ACTION CFC_STATS-3- BADSTATSCLIENTSEND 3-Error [chars]: [chars] 0x%08X/[dec] expected 0x%08X/[dec] Internal error. May result in unpredictable behaviour. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3- BADSTATSCLIENTSEND 3-Error [chars]: [chars] 0x%08X/[dec] expected 0x%08X/[dec] Internal error. May result in unpredictable behaviour. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3- BADSTATSPULL 3-Error [chars]: [chars] Internal error. May result in unpredictable behaviour. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3- BADSTATSPULL 3-Error [chars]: [chars] Internal error. May result in unpredictable behaviour. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3- STATSNOMEM 3-Error CFC Stats failed to allocate memory during [chars] creation. Allocation of memory by the XDR subsystem failed. This may result in an unpredictable behavior of XDR - "Make sure that there is enough memory for the operations being performed " "by your machine. " "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3- STATSNOMEM 3-Error CFC Stats failed to allocate memory during [chars] creation. Allocation of memory by the XDR subsystem failed. This may result in an unpredictable behavior of XDR - "Make sure that there is enough memory for the operations being performed " "by your machine. " "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3-TESTSTATSCLIENT_DECODE 3-Error XDR test stats [chars] saw error [chars]. - - - CFC_STATS-3-TESTSTATSCLIENT_DECODE 3-Error XDR test stats [chars] saw error [chars]. - - - CFC_STATS-3-TESTSTATSCLIENT_UNEXPECTED_EVENT 3-Error Selftest failure: unexpected event [hec] [hec] during The XDR statistics infrastructure has experienced a self test failure. This should only occur when a self test is running and a failure is detected. It does not directly imply a problem with normal operation. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-3-TESTSTATSCLIENT_UNEXPECTED_EVENT 3-Error Selftest failure: unexpected event [hec] [hec] during The XDR statistics infrastructure has experienced a self test failure. This should only occur when a self test is running and a failure is detected. It does not directly imply a problem with normal operation. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- BADSTATSCLIENTRECEIVE 4-Warning context [dec] length [dec] from [chars] The XDR statistics infrastructure received a message it could not decode from a peer. This has no harmful effects but might be a evidence of a more serious problem. XDR_DDTS_COMPONENT "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- BADSTATSCLIENTRECEIVE 4-Warning context [dec] length [dec] from [chars] The XDR statistics infrastructure received a message it could not decode from a peer. This has no harmful effects but might be a evidence of a more serious problem. XDR_DDTS_COMPONENT "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4-STATSCLIENT_REGISTRATION 4-Warning Unable to register XDR client [chars] client due to [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4-STATSCLIENT_REGISTRATION 4-Warning Unable to register XDR client [chars] client due to [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSCLIENTADDMCASTGRPFAIL 4-Warning Stats client [chars] failed to add linecards [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSCLIENTADDMCASTGRPFAIL 4-Warning Stats client [chars] failed to add linecards [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSUNEXPECTEDEVENT 4-Warning [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSUNEXPECTEDEVENT 4-Warning [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSUNEXPECTEDNEWMCASTGRP 4-Warning Add req for [chars] but already sending stats to [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFC_STATS-4- STATSUNEXPECTEDNEWMCASTGRP 4-Warning Add req for [chars] but already sending stats to [chars] The XDR statistics infrastructure has seen an internal error. This may prevent counters to fail to be reported to the RP. - "Copy the message exactly as it appears and report it to your technical " "support representative." CFG_MGR-4-BOOTLOADER 4-Warning [chars] for Switch [dec] Switch needs to be upgraded to latest Rommon version - "This is a notification message" " To upgrade the switch to latest rommon using CLI " " upgrade rom-monitor capsule primary switch [number] R0" " Please Do not Power cycle your switch during upgrade" CFGD_LBL_REGION-4-LCON 4-Warning ERRMSG_NOFLAGS - - - CFGD_LBL_REGION-4-LCON 4-Warning ERRMSG_NOFLAGS - - - CFT_API-3-CFT_ERRMSG_MAX_MEMORY 3-Error [chars] [chars] [dec] The maximum number of concurrent flows allowed has been exceeded. Some flows might not received the provisioned level of service. common-flow-table "This is the platform limit. Either lower the network load on this device " "or upgrade to a higher capacity platform." LOG_STD_SH_TECH_ACTION CFT_API-3-CFT_ERRMSG_MAX_MEMORY 3-Error [chars] [chars] [dec] The maximum number of concurrent flows allowed has been exceeded. Some flows might not received the provisioned level of service. common-flow-table "This is the platform limit. Either lower the network load on this device " "or upgrade to a higher capacity platform." LOG_STD_SH_TECH_ACTION CFT_API-3-CFT_ERRMSG_NO_MEMORY 3-Error [chars] [chars] [dec] The system was unable to supply the requested memory for flow processing to continue. common-flow-table - CFT_API-3-CFT_ERRMSG_NO_MEMORY 3-Error [chars] [chars] [dec] The system was unable to supply the requested memory for flow processing to continue. common-flow-table - CFT_API-3-CFT_ERRMSG_UNKNOWN 3-Error [chars] [chars] [dec] The error message type does not match the possible enumerated definitions. common-flow-table "This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION CFT_API-3-CFT_ERRMSG_UNKNOWN 3-Error [chars] [chars] [dec] The error message type does not match the possible enumerated definitions. common-flow-table "This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION CFT_API-4-CFT_ERRMSG_CLIENT_PRE_CREATE_PREVENTED 4-Warning [chars] [chars] [dec] Flow creation was prevented by a flow table client. This may be due to an explicit policy that is enabled. common-flow-table "Check your policies to ensure this what you intend." LOG_STD_SH_TECH_ACTION CFT_API-4-CFT_ERRMSG_CLIENT_PRE_CREATE_PREVENTED 4-Warning [chars] [chars] [dec] Flow creation was prevented by a flow table client. This may be due to an explicit policy that is enabled. common-flow-table "Check your policies to ensure this what you intend." LOG_STD_SH_TECH_ACTION CFT_API-4-CFT_ERRMSG_FLOW_CREATION_PREVENTED 4-Warning [chars] [chars] [dec] Flow creation was denied by a the system. A possible denial of service attack may have been detected. common-flow-table "Modify your denial of service policy if this is in error." LOG_STD_SH_TECH_ACTION CFT_API-4-CFT_ERRMSG_FLOW_CREATION_PREVENTED 4-Warning [chars] [chars] [dec] Flow creation was denied by a the system. A possible denial of service attack may have been detected. common-flow-table "Modify your denial of service policy if this is in error." LOG_STD_SH_TECH_ACTION CFT_API-5-CFT_ERRMSG_NON_FIRST_IP_FRAGMENT 5-Notice [chars] [chars] [dec] The flow table was unable to process a TCP fragmented packet. Service for these packets may be unavailable. common-flow-table "Enable the virtual fragment reassembly VFR functionality." CFT_API-5-CFT_ERRMSG_NON_FIRST_IP_FRAGMENT 5-Notice [chars] [chars] [dec] The flow table was unable to process a TCP fragmented packet. Service for these packets may be unavailable. common-flow-table "Enable the virtual fragment reassembly VFR functionality." CFT_API-5-CFT_ERRMSG_UNSUPPORTED_L3_PROTOCOL 5-Notice [chars] [chars] [dec] An unsupported layer 3 protocol was identified. common-flow-table "Flow based inspection does not support this protocol at this time." LOG_STD_SH_TECH_ACTION CFT_API-5-CFT_ERRMSG_UNSUPPORTED_L3_PROTOCOL 5-Notice [chars] [chars] [dec] An unsupported layer 3 protocol was identified. common-flow-table "Flow based inspection does not support this protocol at this time." LOG_STD_SH_TECH_ACTION CFT_API-7-CFT_ERRMSG_CLIENT_API 7-Debug [chars] [chars] [dec] A CFT client may have a incorrectly accessed an API. common-flow-table "This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION CFT_API-7-CFT_ERRMSG_CLIENT_API 7-Debug [chars] [chars] [dec] A CFT client may have a incorrectly accessed an API. common-flow-table "This is an internal software error. Please report it to your technical " "support representative." LOG_STD_SH_TECH_ACTION CFT_CLIENT-4-CFT_MEMORY_BOUNDARY_TOUCH_CLEAR 4-Warning CFT memory utilization has declined below its threshold memory is available for [chars]. After CFT was in memory shortage memory utilization has declined below its threshold New traffic flows will be opened properly qfp-cft LOG_STD_ACTION CFT_CLIENT-4-CFT_MEMORY_BOUNDARY_TOUCH_WARN 4-Warning CFT reached maximum configured memory utilization. Can't allocate more memory for [chars]. Because of CFT memory shortage new flows may not be opened properly qfp-cft LOG_STD_ACTION CFT_CLIENT-4-MAX_FCS_TOUCH_CLEAR 4-Warning CFT number of [chars] has declined below its threshold flow contexts are available for [chars]. After CFT was in flow contexts shortage the number of flow contexts has declined below its threshold. New traffic flows will be opened properly qfp-cft LOG_STD_NO_ACTION CFT_CLIENT-4-MAX_FCS_TOUCH_WARN 4-Warning CFT number of [chars] threshold is reached can't allocate more memory for [chars]. Because of non-availability of flow contexts new traffic flows may not be opened qfp-cft LOG_STD_NO_ACTION CFT_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_CLEAR 4-Warning System free memory has increased above its lower watermark memory is available for [chars]. After system memory was in shortage free memory has increased above its lower watermark New traffic flows will be opened properly qfp-cft LOG_STD_ACTION CFT_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_WARN 4-Warning System free memory has reached its lower watermark. Can't allocate more memory for [chars]. Because of system memory shortage new flows may not be opened properly qfp-cft LOG_STD_ACTION CFT_CONGESTION_STATE-4-CPU_THRESHOLD_CHANGE 4-Warning CPU Threshold has been changed to [dec]%%. CPU threshold has been changed. cpp-ucode LOG_STD_ACTION CFT_CONGESTION_STATE-4-MAX_BACKOFF_CHANGE 4-Warning Maximum back-off timeout has been changed to [dec]. Maximum back-off timeout has been changed. cpp-ucode LOG_STD_ACTION CFT_CONGESTION_STATE-4-STATE_CHANGED_TO_GRADUAL_BRINGUP 4-Warning CPU Utilization:[dec]%%. CPU usage regulation state is now: Gradual bring-up. CFT Congestion state changed to Gradual bring-up cpp-ucode LOG_STD_ACTION CFT_CONGESTION_STATE-4-STATE_CHANGED_TO_SELF_REGULATED 4-Warning CPU Utilization is high:[dec]%% CPU usage regulation state is now: Self-regulated. CFT Congestion state changed to Self-regulated. cpp-ucode LOG_STD_ACTION CFT_CONGESTION_STATE-6-STATE_CHANGED_TO_NORMAL 6-Information CPU Utilization back to normal CPU usage regulation state is now: Normal. CFT Congestion state back to normal. cpp-ucode LOG_STD_ACTION CFT_CONGESTION_STATE-6-STATE_DEFAULT 6-Information CPU-usage regulation parameters have been changed to default. Max back-off timeout:[dec] seconds CPU threshold [dec]%%. Parameters to default. cpp-ucode LOG_STD_ACTION CFT-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the CFT feature failed. This will cause the feature to not function. qfp-cft "This is normally a software issue. " "The consequences are that the CFT feature will not function. " LOG_STD_ACTION CFT-3-HA_INVALID_BULK_SYNC 3-Error Invalid message length for bulk sync got [dec] expected [dec] Standby received an unrecognized VRF name hash cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_ID_BULK_SYNC 3-Error Invalid feature id for bulk sync got [dec] expected [dec] Standby received an unrecognized VRF name hash cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_MSG_LEN_RCVD 3-Error invalid [chars] rg [dec] [dec] expected [dec] opcode [chars] [hec] Standby received an invalid Firewall HA message cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_MSG_NO_V6KEY_RCVD 3-Error Missing IPv6 key - rg: [dec] len: [dec] msg type: \[chars]\ [hec] flow type: [dec] Standby received an invalid Firewall HA message cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_MSG_RCVD 3-Error invalid [chars] [hec] opcode [chars] [hec] Standby received an invalid Firewall HA message cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_MSG_VRF_HASH 3-Error [chars]: rg: [dec] [inet]:[dec] [inet]:[dec] [dec] i_vrf_hash: 0x%llx r_vrf_hash: 0x%llx Standby received an unrecognized VRF name hash cpp-ucode LOG_STD_ACTION CFT-3-HA_INVALID_RG_RCVD 3-Error invalid [chars] opcode [chars] [dec] - rg [dec]:[dec] Standby received an invalid Redundancy group cpp-ucode LOG_STD_ACTION CFT-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper CFT software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-cft "This is normally a software issue. " LOG_STD_RECUR_ACTION CFT-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper CFT software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-cft "This is normally a software issue. " LOG_STD_RECUR_ACTION CGC-0-CGC_EMERG 0-Emergency [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-0-CGC_EMERG 0-Emergency [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-0-CGC_EMERG 0-Emergency [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-0-CGC_EMERG 0-Emergency [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-1-CGC_ALERT 1-Alert [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-1-CGC_ALERT 1-Alert [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-1-CGC_ALERT 1-Alert [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-1-CGC_ALERT 1-Alert [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-2-CGC_CRIT 2-Critical [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-2-CGC_CRIT 2-Critical [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-2-CGC_CRIT 2-Critical [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-2-CGC_CRIT 2-Critical [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-3-CGC_ERR 3-Error [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-3-CGC_ERR 3-Error [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-3-CGC_ERR 3-Error [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-3-CGC_ERR 3-Error [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-4-CGC_WARNING 4-Warning [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-4-CGC_WARNING 4-Warning [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-4-CGC_WARNING 4-Warning [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-4-CGC_WARNING 4-Warning [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-5-CGC_NOTICE 5-Notice [chars] Normal but significant conditions CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-5-CGC_NOTICE 5-Notice [chars] Normal but significant conditions CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-5-CGC_NOTICE 5-Notice [chars] Normal but significant conditions CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-5-CGC_NOTICE 5-Notice [chars] Normal but significant conditions CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-6-CGC_INFO 6-Information [chars] Informational messages CGC_DDTS_COMPONENT LOG_STD_NO_ACTION CGC-6-CGC_INFO 6-Information [chars] Informational messages CGC_DDTS_COMPONENT LOG_STD_NO_ACTION CGC-6-CGC_INFO 6-Information [chars] Informational messages CGC_DDTS_COMPONENT LOG_STD_NO_ACTION CGC-6-CGC_INFO 6-Information [chars] Informational messages CGC_DDTS_COMPONENT LOG_STD_NO_ACTION CGC-7-CGC_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-7-CGC_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-7-CGC_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGC-7-CGC_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CGC_INTERNAL_ERROR CGC_DDTS_COMPONENT LOG_STD_ACTION CGM-3-CGM_FIPS_BYPASS_TEST 3-Error NIST bypass test failed for CGM object [chars]. Class-Group Manager Security Client database detected a discrepancy in a security sensitive object. This could be due to a hardware or software resource limitation or a software defect. qfp-class-internal "Check the logs for information on the relevant " "object download states. Remove the object or a " "parent object in question. If the problem persists " "reboot the forwarding processor ESP." CGM-3-CGM_FIPS_BYPASS_TEST 3-Error - - - - CGM-3-CGM_SHARED_MEM_ERROR 3-Error CGM shared memory allocation failed: [chars] - - - CHASSIS-3-OPERATION_FORBIDDEN 3-Error [chars] and try again. There are two ejcet buttons on PRE5 front panel. When both eject buttons are pulled out or a CLI plugin-card-preotec enable/disable So the software modules protected by this may fail such as write/erase based on bootflash chip cr10k5 "Please tighten the screws of the eject button." CHASSIS-3-PROCESSERR 3-Error Couldn't start tempeature enviroment monitoring process The temperature monitoring process could not be started during initialization. cr10k5 LOG_STD_ACTION CHASSIS-4-READALERTRESERR 4-Warning MAX1668 [dec] read alert response address error MAX1668 read alert response address failed. cr10k5 LOG_STD_ACTION CHASSIS-6-EJECT_BUTTON 6-Information [chars] eject button is being screwed on/off. There are two ejcet buttons on PRE5 front panel. When any eject button is being screwed on/off the error message will be printed to screen to remind the user. cr10k5 LOG_STD_ACTION CHAT-3-CANTRUN 3-Error [t-line] in use can't run startup script When the startup script attempted to run it found another process had\n\ Already been started on the line chat "Remove startup script from line configuration if it's inappropriate.\n\ Report to cisco." CHKPT-3-CHKPT_MSG_NULL 3-Error The chkpt message has an empty data buffer This is a severe error as far as checkpointing is concerned. The chkpt message's data buffer is NULL indicating that there were no memory resources to assign while getting a buffer. checkpoint "Check whether this error goes away when the " "memory is increased else " LOG_STD_SH_TECH_ACTION CHKPT-3-CHKPT_MSG_NULL 3-Error The chkpt message has an empty data buffer This is a severe error as far as checkpointing is concerned. The chkpt message's data buffer is NULL indicating that there were no memory resources to assign while getting a buffer. checkpoint "Check whether this error goes away when the " "memory is increased else " LOG_STD_SH_TECH_ACTION CHKPT-3-ILLEGAL 3-Error ILLEGAL call to CF API by client [dec] on the [chars] system An illegal API call was made by a CF client checkpoint "Find out the offending client using " LOG_STD_SH_TECH_ACTION CHKPT-3-ILLEGAL 3-Error ILLEGAL call to CF API by client [dec] on the [chars] system An illegal API call was made by a CF client checkpoint "Find out the offending client using " LOG_STD_SH_TECH_ACTION CHKPT-3-INVALID_CALLBACK_ARG 3-Error Attempt to add a checkpointing client with an invalid [chars] argument Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An invalid argument was supplied to an internal API. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred. The system state between one or more checkpointing clients might not be properly synchronized. checkpoint LOG_STD_ACTION CHKPT-3-INVALID_CALLBACK_ARG 3-Error Attempt to add a checkpointing client with an invalid [chars] argument Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An invalid argument was supplied to an internal API. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred. The system state between one or more checkpointing clients might not be properly synchronized. checkpoint LOG_STD_ACTION CHKPT-3-INVALID_ENTITY_MSG_ID 3-Error Invalid message event received [dec] - - - CHKPT-3-INVALID_ENTITY_MSG_ID 3-Error Invalid message event received [dec] - - - CHKPT-3-IPCPORT 3-Error Unable to create IPC port on [chars] A severe checkpoint error occurred because the system was unable to allocate the resources needed to create a communications port for the Interprocess Communications IPC channel needed to checkpoint "Increase the memory. If the error persists" LOG_STD_SH_TECH_ACTION CHKPT-3-IPCPORT 3-Error Unable to create IPC port on [chars] A severe checkpoint error occurred because the system was unable to allocate the resources needed to create a communications port for the Interprocess Communications IPC channel needed to checkpoint "Increase the memory. If the error persists" LOG_STD_SH_TECH_ACTION CHKPT-3-IPCREGISTER 3-Error Unable to register IPC port on [chars] Checkpoint Facility was unable to register an IPC port. This can happen when registering a port that hasn't yet been created. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-IPCREGISTER 3-Error Unable to register IPC port on [chars] Checkpoint Facility was unable to register an IPC port. This can happen when registering a port that hasn't yet been created. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-IPCSESSION 3-Error Unable to open an IPC session with [chars] A severe checkpointing error occured as the system was unable to establish an interprocess communications session between the Active and the Standby peers. checkpoint "As this failure hinders any communication from taking place " "between the Active and the Standby peers reset the Standby. " "If the error persists" LOG_STD_SH_TECH_ACTION CHKPT-3-IPCSESSION 3-Error Unable to open an IPC session with [chars] A severe checkpointing error occured as the system was unable to establish an interprocess communications session between the Active and the Standby peers. checkpoint "As this failure hinders any communication from taking place " "between the Active and the Standby peers reset the Standby. " "If the error persists" LOG_STD_SH_TECH_ACTION CHKPT-3-ISSU_MSG_NOT_COMPATIBLE 3-Error Checkpointing message type not compatible Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An error was detected when verifying the checkpointing message type compatibility between checkpointing client peers. The failure most likely occurred because of a software error. The system state between one or more checkpointing clients might not be properly synchronized. checkpoint "show checkpoint client" CHKPT-3-ISSU_MSG_NOT_COMPATIBLE 3-Error Checkpointing message type not compatible Checkpointing messages are used to carry encoded information for transfer between various High-Availabilty clients. For example to synchronize state information between redundant route processor units. An error was detected when verifying the checkpointing message type compatibility between checkpointing client peers. The failure most likely occurred because of a software error. The system state between one or more checkpointing clients might not be properly synchronized. checkpoint "show checkpoint client" CHKPT-3-ISSU_NEGO_FAILED 3-Error Checkpointing Facility failed to start ISSU negotiation with the peer [chars] Checkpointing Facility was unable to start the ISSU negotiation successfully. ISSU negotiation is done during system initialization or if the Standy system is signing in with the Active system. The failure to start negotiation is a fatal error condition and most likely occured because of a software error. checkpoint "show tech" CHKPT-3-ISSU_NEGO_FAILED 3-Error Checkpointing Facility failed to start ISSU negotiation with the peer [chars] Checkpointing Facility was unable to start the ISSU negotiation successfully. ISSU negotiation is done during system initialization or if the Standy system is signing in with the Active system. The failure to start negotiation is a fatal error condition and most likely occured because of a software error. checkpoint "show tech" CHKPT-3-ISSU_RCV_TRANSFORM_FAILED 3-Error Checkpointing receive message header transformaton failed [chars] - - - CHKPT-3-ISSU_RCV_TRANSFORM_FAILED 3-Error Checkpointing receive message header transformaton failed [chars] - - - CHKPT-3-ISSU_XMIT_TRANSFORM_FAILED 3-Error Checkpointing transmit message header transformaton failed [chars] - - - CHKPT-3-ISSU_XMIT_TRANSFORM_FAILED 3-Error Checkpointing transmit message header transformaton failed [chars] - - - CHKPT-3-NO_RESOURCES 3-Error [chars] A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized. checkpoint "If you determine that this condition was caused by a lack of system " "memory reduce system activity to ease memory demands or if conditions " "warrant upgrade to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION CHKPT-3-NO_RESOURCES 3-Error [chars] A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized. checkpoint "If you determine that this condition was caused by a lack of system " "memory reduce system activity to ease memory demands or if conditions " "warrant upgrade to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION CHKPT-3-NOMEM 3-Error Unable to allocate resources for CF on [chars]. This error occurs when there are no memory resources available. This is a severe error as far as check pointing is concerned checkpoint "Reduce other system activity to ease memory demands. Add more memory. " "If enough memory is available try to see whether the problem goes away " "by reloading the router. If not then" LOG_STD_SH_TECH_ACTION CHKPT-3-NOMEM 3-Error Unable to allocate resources for CF on [chars]. This error occurs when there are no memory resources available. This is a severe error as far as check pointing is concerned checkpoint "Reduce other system activity to ease memory demands. Add more memory. " "If enough memory is available try to see whether the problem goes away " "by reloading the router. If not then" LOG_STD_SH_TECH_ACTION CHKPT-3-REGISTERATION_FAILED 3-Error Failed to register with [chars] rc = [dec] An internal failure associated with client registration occurred in the run-time module specified in the message output. The return code that is specified in the message output identifies the type of failure that was detected. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-REGISTERATION_FAILED 3-Error Failed to register with [chars] rc = [dec] An internal failure associated with client registration occurred in the run-time module specified in the message output. The return code that is specified in the message output identifies the type of failure that was detected. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-RFREG 3-Error Unable to register checkpoint as client of RF. This is a severe error as far as check pointing is concerned checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-RFREG 3-Error Unable to register checkpoint as client of RF. This is a severe error as far as check pointing is concerned checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-RMI_CALLBACK 3-Error Checkpointing Facility encountered an error while processing a callback from the Resource Manager RMI [chars] Checkpointing Facility registers with the Resource Manager RMI to checkpoint "show tech" CHKPT-3-RMI_CALLBACK 3-Error Checkpointing Facility encountered an error while processing a callback from the Resource Manager RMI [chars] Checkpointing Facility registers with the Resource Manager RMI to checkpoint "show tech" CHKPT-3-RMI_FAILED 3-Error Checkpointing Facility failed to register with the Resource Manager RMI [chars] Checkpointing Facility registers with the Resource Manager RMI to checkpoint "show tech" CHKPT-3-RMI_FAILED 3-Error Checkpointing Facility failed to register with the Resource Manager RMI [chars] Checkpointing Facility registers with the Resource Manager RMI to checkpoint "show tech" CHKPT-3-SYSMGR_LOOKUP 3-Error Failed to get process Job ID from SysMgr Failed to get the Job ID for this ION process from SysMgr. The checkpoint "show tech" CHKPT-3-SYSMGR_LOOKUP 3-Error Failed to get process Job ID from SysMgr Failed to get the Job ID for this ION process from SysMgr. The checkpoint "show tech" CHKPT-3-TIMER 3-Error [chars] Checkpoint Facility was unable to retrieve the correct context for a previously saved message descriptor. This is most likely a software error caused by possible memory corruption. checkpoint LOG_STD_ACTION CHKPT-3-TIMER 3-Error [chars] Checkpoint Facility was unable to retrieve the correct context for a previously saved message descriptor. This is most likely a software error caused by possible memory corruption. checkpoint LOG_STD_ACTION CHKPT-3-TRANSMIT_FAILED 3-Error Checkpointing message transmission failure [chars] - - - CHKPT-3-TRANSMIT_FAILED 3-Error Checkpointing message transmission failure [chars] - - - CHKPT-3-UNKNOWNMSG 3-Error Unknown message received from peer on the standby for client [dec]. This is a severe error as far as check pointing is concerned. This will be caused when one of the peers can some checkpoint message types that the other side does not understand. This is caused due to a software error as the set of messages being exchanged by either side must be the same. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-3-UNKNOWNMSG 3-Error Unknown message received from peer on the standby for client [dec]. This is a severe error as far as check pointing is concerned. This will be caused when one of the peers can some checkpoint message types that the other side does not understand. This is caused due to a software error as the set of messages being exchanged by either side must be the same. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-DISABLED 4-Warning Check Pointing is disabled. Client [chars] should not be calling any CF API This is mainly a warning and might be due to timing issue checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-DISABLED 4-Warning Check Pointing is disabled. Client [chars] should not be calling any CF API This is mainly a warning and might be due to timing issue checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-DUPID 4-Warning Duplicate checkpoint client ID [dec]. A checkpoint client is using a client ID which is already assigned to an another client. This could be due to a synchronization delay which will typically resolve itself. This would happen when an already registered Checkpointing Facility client again tries to add itself. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-DUPID 4-Warning Duplicate checkpoint client ID [dec]. A checkpoint client is using a client ID which is already assigned to an another client. This could be due to a synchronization delay which will typically resolve itself. This would happen when an already registered Checkpointing Facility client again tries to add itself. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-FREE_BUFFER 4-Warning Checkpointing [dec] failed to free buffer Checkpointing failed to free a buffer. This may cause leak in memory resources. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-FREE_BUFFER 4-Warning Checkpointing [dec] failed to free buffer Checkpointing failed to free a buffer. This may cause leak in memory resources. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-GET_BUFFER 4-Warning Checkpointing ISSU failed to get buffer. Dest seat id 0x[hec] Checkpointing ISSU failed to get a buffer. This is due to the dearth of memory resources. checkpoint "Upgrade the memory. If the error " "persists " LOG_STD_SH_TECH_ACTION CHKPT-4-GET_BUFFER 4-Warning Checkpointing ISSU failed to get buffer. Dest seat id 0x[hec] Checkpointing ISSU failed to get a buffer. This is due to the dearth of memory resources. checkpoint "Upgrade the memory. If the error " "persists " LOG_STD_SH_TECH_ACTION CHKPT-4-INIT 4-Warning Checkpoint [chars] initialization failed in RF state [chars] Checkpointing initialization has failed This is software error caused by an out of memory condition as there aren't enough resources available to set up the initialization data structures checkpoint "Upgrade the memory. If the error " "persists " LOG_STD_ACTION CHKPT-4-INIT 4-Warning Checkpoint [chars] initialization failed in RF state [chars] Checkpointing initialization has failed This is software error caused by an out of memory condition as there aren't enough resources available to set up the initialization data structures checkpoint "Upgrade the memory. If the error " "persists " LOG_STD_ACTION CHKPT-4-INVALID_CLIENT 4-Warning Invalid checkpoint client ID [dec]. The client id is invalid. This error has occured since the corresponding client is not present. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-INVALID_CLIENT 4-Warning Invalid checkpoint client ID [dec]. The client id is invalid. This error has occured since the corresponding client is not present. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-INVALID_ENTITY 4-Warning Invalid checkpoint entity ID [dec]. The entity id is invalid. This error has occured since the corresponding entity is not present. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-INVALID_ENTITY 4-Warning Invalid checkpoint entity ID [dec]. The entity id is invalid. This error has occured since the corresponding entity is not present. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-MSG_SEND 4-Warning Checkpointing ISSU failed to send message. Dest seat id 0x[hec] Checkpointing ISSU failed to send nego message to peer. This will be due to an out of memory condition communication with the peer being severed checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-MSG_SEND 4-Warning Checkpointing ISSU failed to send message. Dest seat id 0x[hec] Checkpointing ISSU failed to send nego message to peer. This will be due to an out of memory condition communication with the peer being severed checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOCLIENT 4-Warning CF client is NULL [chars] Checkpoint Facility cannot send the message as the client is NULL. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOCLIENT 4-Warning CF client is NULL [chars] Checkpoint Facility cannot send the message as the client is NULL. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOIPCPORT 4-Warning IPC port is NULL [chars] Checkpoint Facility cannot send the message as the IPC port information is NULL. This message appears since since the communication session between the Checkpointing Facility peers has not yet been established. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOIPCPORT 4-Warning IPC port is NULL [chars] Checkpoint Facility cannot send the message as the IPC port information is NULL. This message appears since since the communication session between the Checkpointing Facility peers has not yet been established. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOMESSAGE 4-Warning Message is NULL [chars] Checkpoint Facility cannot send the message as the message is NULL. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-NOMESSAGE 4-Warning Message is NULL [chars] Checkpoint Facility cannot send the message as the message is NULL. checkpoint LOG_STD_SH_TECH_ACTION CHKPT-4-PAK_MGR_CONN 4-Warning Failed to connect to the Packet Manager During Checkpoint initialization unable to create a connection to the Packet Manager. This could result in the CF infra unable to access shared memory in the client context using a virtual address. checkpoint LOG_STD_ACTION CHKPT-4-PAK_MGR_CONN 4-Warning Failed to connect to the Packet Manager During Checkpoint initialization unable to create a connection to the Packet Manager. This could result in the CF infra unable to access shared memory in the client context using a virtual address. checkpoint LOG_STD_ACTION CHKPT-4-PAK_RECLAIM 4-Warning Failed to reclaim packet from Packet Manager client [chars] After the message send failed the CF client was unable to reclaim the packet to be able to free the message. checkpoint LOG_STD_ACTION CHKPT-4-PAK_RECLAIM 4-Warning Failed to reclaim packet from Packet Manager client [chars] After the message send failed the CF client was unable to reclaim the packet to be able to free the message. checkpoint LOG_STD_ACTION CHKPT-5-HIGHBUFFER 5-Notice Checkpoint client using Large No. of Buffers in domain [dec] are [chars] Several IPC messages are pending to be processed by or delevered to checkpoint "show checkpoint statistics buffer-usage" CHKPT-5-HIGHBUFFER 5-Notice Checkpoint client using Large No. of Buffers in domain [dec] are [chars] Several IPC messages are pending to be processed by or delevered to checkpoint "show checkpoint statistics buffer-usage" CHUNK-3-CHUNK_BAD_REFCNT 3-Error refcnt=[dec] data=0x[hec] The memory chunk manager detected a bad reference count cpp-ucode LOG_STD_ACTION CHUNK-3-INVALID_ELEM_SIZE 3-Error requested [dec] Memory corruption was detected by the memory chunk manager cpp-ucode LOG_STD_ACTION CHUNK-3-SIBLING_ERR 3-Error Tried to destroy sibling memory chunk 0x[hec] An invalid sibling condition was hit in the Memory Chunk Manager cpp-ucode LOG_STD_ACTION CI-1-BLOWSHUT 1-Alert Blower failure shutdown in [dec] seconds One of the six blowers in a five-slot chassis has failed. Because each blower cools a separate region of the cards in the chassis all blowers are needed for router operation. If a blower failure persists for 2 minutes the router will shut itself down and will need to be power cycled. - LOG_STD_ACTION CI-2-ENVCRIT 2-Critical [chars] measured at [chars] One of the measured environmental test points exceeds an extreme threshold. - "Correct the specified condition or the router may shut itself down or fail to operate properly." CI-2-INT 2-Critical Unexpected interrupt - status %02x An unexpected interrupt occurred. This is a serious software error which will be followed by a core dump. - LOG_STD_ACTION CI-3-BLOWER 3-Error [chars] fan failure One of the router's cooling fans failed. - "Replace the fan as soon as possible or the router may shut itself down or fail to operate properly." CI-3-CTRLRTYPE 3-Error Wrong controller type %02x The CI was manufactured incorrectly. - "Copy the error message exactly as it appears and report it to your technical support representative." CI-3-NOACK 3-Error [chars] acknowledge failure cmd %02x addr %02x data %02x The CI software failed to communicate with the CI hardware. - "Copy the error message exactly as it appears and report it to your technical support representative." CI-3-PSFAIL 3-Error Power supply [dec] failure One of the router's power supplies failed. - "Replace the failed power supply as soon as possible." CI-3-SLOTCOMP 3-Error Inconsistent [chars] slot %02x The CI software detected a possible inconsistency in the CI hardware. - "Confirm that the CI card is correctly and fully installed in the backplane. If error recurs call your technical support representative for assistance." CI-4-COND 4-Warning Restarting with [dec] recent soft power shutdowns\n\t\tor system just powered-on A soft shutdown occurs when the router powers itself down due to a detected over temperature condition. When the temperature goes up past the board shutdown trip point the cards are shutdown but the power supplies fans and CI continue to run. When the system cools past the restart trip point the system will restart. The system counts the number of times this happens to keep the up/down cycle from repeating indefinitely. If the above counter reaches zero the system undergoes a hard shutdown which requires a power cycle to recover. The soft shutdown counter is reset to its maximum value after the system has been up for six hours. - "Copy the error message exactly as it appears and report it to your technical support representative." CI-4-ENVWARN 4-Warning [chars] measured at [chars] One of the measured environmental test points exceeds the warning threshold. - "Closely monitor the condition and correct if possible. If the situation worsens call your technical support representative for assistance." CI-4-MAXOUTPUT 4-Warning Power supply [dec] [dec]V is at or near rated output This indicates that the power supply is delivering its maximum rated current. This condition is not a problem unless the current continues to increase beyond the rated limit of the power supply which can cause hardware damage. - LOG_STD_ACTION CI-4-NOTFOUND 4-Warning Chassis Interface not found The system software could not detect the presence of a CI card. - "Verify that the CI card is correctly and fully installed in the backplane. If the error recurs call your technical support representative for assistance." CI-4-SYSLOAD 4-Warning System [dec]V load exceeds single power supply [dec] capacity This warning message indicates that the system's electrical current usage exceeds the capacity of a single power supply. During this condition power supplies must not be removed from the system. - - CI-4-UNBALANCE 4-Warning Unbalanced [dec]V output from dual power supplies The difference in electrical current output between the two power supplies is out of tolerance for the system design. One of the power supplies may be failing or about to fail. - LOG_STD_ACTION CI-6-BPLANE 6-Information CI type [dec] differs from NVRAM type [dec] The chassis type as reported by the CI is different from that programmed into NVRAM. - "Copy the error message exactly as it appears and report it to your technical support representative." CI-6-PSCHANGE 6-Information Power supply [dec] changed from [chars] to [chars] The CI reported that a power supply was either installed removed or changed. - "If the situation does not correspond with a physical change in the system's power supplies call your technical support representative for assistance." CI-6-PSNORMAL 6-Information Power supply [dec] normal One of the router's failed power supplies are working normal now. - "If the situation does not correspond with a normal operation of the system's power supplies call your technical support representative for assistance." CIPDUMP-3-CIP_CORE_DUMP_ERROR 3-Error CIP core dump error slot [dec]: [chars] An error occured during a CIP core dump - "None." CIPDUMP-6-CIP_CORE_DUMP_PROGRESS 6-Information Dump of slot [dec] core [chars]. Progress messages for CIP core dump. - "None." CIRRUS-1-NOMEMORY 1-Alert msgtxt_nomemory An operation could not be accomplished because of a low memory\n\ condition. - LOG_STD_REDUCE_ACTION CIRRUS-3-BADENCAP 3-Error msgtxt_badencap - - "" CIRRUS-3-BADHDXFSM 3-Error Interface serial [dec] Unexpected HDX state [dec] event [dec] An internal software error occurred. - LOG_STD_SH_TECH_ACTION CIRRUS-3-BADMODE 3-Error Interface serial [dec] Bad mode encountered in init An internal software error occurred. - LOG_STD_SH_TECH_ACTION CIRRUS-3-BADRXISR 3-Error Interface serial [dec] Unexpected situation in receive ISR An internal software error occurred while receiving data. - LOG_STD_SH_TECH_ACTION CIRRUS-3-BADTXISR 3-Error Interface serial [dec] Unexpected situation in transmit ISR An internal software error occurred while transmitting data. - LOG_STD_SH_TECH_ACTION CIRRUS-3-HWNORESPONSE 3-Error The CD2430 Controller is not responding power cycle the router The CD2430 controller has failed to respond to your request.\n\ This is due to unsupported clocking or the use\n\ of a non-standard cable. - "Check the clocking and cable. Use cisco cables only. " LOG_STD_RECUR_ACTION CIRRUS-3-RESETERR 3-Error CD2430 serial controller [dec] Reset timeout error The async controller failed to respond to a reset command.\n\ This may indicate a hardware failure. - "Reset the interface or controller.\n\ Cycle the power if necessary. " LOG_STD_RECUR_ACTION CIRRUS-3-SETCHAN 3-Error Serial[dec]: setchan called in CD2430 interrupt context An internal software error occurred. - LOG_STD_SH_TECH_ACTION CIRRUS-4-DOWNREV_NM 4-Warning Network Module card in slot [dec] is incompatible with the system. The network module in this slot is an old revision which is not \n\ compatible with this system. Please upgrade that network module. - LOG_STD_SH_TECH_ACTION CIRRUS-5-LINEFLAP 5-Notice Unit [dec] excessive modem control changes The specified async interface was determined to have too many\n\ automatic control changes in too short a span of time.\n\ This may indicate a hardware or software error in the interface. - "Reset the interface. " LOG_STD_RECUR_ACTION CISCO_STUN-3-INTERTNAL_ERROR 3-Error Unable to process STUN message received on IP address [chars] and port [dec] failed with value [dec] Unable to processs the received STUN packet. Could be due to no ICE instance present to handle this packet or the STUN message has a wrong method or stray packet ipipgw LOG_STD_RECUR_ACTION CISCO_STUN-3-INTERTNAL_ERROR 3-Error Unable to process STUN message received on IP address [chars] and port [dec] failed with value [dec] Unable to processs the received STUN packet. Could be due to no ICE instance present to handle this packet or the STUN message has a wrong method or stray packet ipipgw LOG_STD_RECUR_ACTION CISCO_STUN-3-NORESOURCE 3-Error No resources for [chars] An error was encountered while trying to obtain memory resources for an internal queue or table. If malloc errors where also seen then that is most likely the root of the problem. If no memory allocation errors have occurred then this may be an internal problem. ipipgw "If there were memory allocation errors at the" "same time as this error then this error can be ignored. Otherwise: " LOG_STD_SH_TECH_ACTION CISCO_STUN-3-NORESOURCE 3-Error No resources for [chars] An error was encountered while trying to obtain memory resources for an internal queue or table. If malloc errors where also seen then that is most likely the root of the problem. If no memory allocation errors have occurred then this may be an internal problem. ipipgw "If there were memory allocation errors at the" "same time as this error then this error can be ignored. Otherwise: " LOG_STD_SH_TECH_ACTION CISCO_STUN-3-PARSE_ERROR 3-Error Parsing of STUN message received on IP address [chars] and port [dec] failed with value [dec] Parsing of one of STUN attribute failed due to invalid value or not present or received STUN message has invalid header ipipgw LOG_STD_RECUR_ACTION CISCO_STUN-3-PARSE_ERROR 3-Error Parsing of STUN message received on IP address [chars] and port [dec] failed with value [dec] Parsing of one of STUN attribute failed due to invalid value or not present or received STUN message has invalid header ipipgw LOG_STD_RECUR_ACTION CISCO_STUN-3-QUEUE_ERROR 3-Error Unable to enqueue event [chars] [dec] to a process watched queue. Current size: [dec] max size: [dec] - - - CISCO_STUN-3-QUEUE_ERROR 3-Error Unable to enqueue event [chars] [dec] to a process watched queue. Current size: [dec] max size: [dec] - - - CISCO_STUN-4-ICE_ROLE_CONFLICT 4-Warning Ice Role Conflcit detected in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a role-conflcit determined as per procedures of RFC 5245. CUBE has responded with a ERROR-CODE attribute of with a value of 487 Role Conflict but retains its role. ipipgw LOG_STD_NO_ACTION CISCO_STUN-4-ICE_ROLE_CONFLICT 4-Warning Ice Role Conflcit detected in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a role-conflcit determined as per procedures of RFC 5245. CUBE has responded with a ERROR-CODE attribute of with a value of 487 Role Conflict but retains its role. ipipgw LOG_STD_NO_ACTION CISCO_STUN-4-INVALID_MESSAGE_INTEGRITY 4-Warning Invalid Message-Integrity attribute in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a wrong Message-Integrity. This could mean the sending device has not computed the integrity of the STUN payload before it sends out Or it has changed the payload after it has computed the integrity and hence the integrity is wrong. CUBE has not honoured this STUN message and has responded with STUN error response with a error code 400 as per RFC 5389 ipipgw LOG_STD_NO_ACTION CISCO_STUN-4-INVALID_MESSAGE_INTEGRITY 4-Warning Invalid Message-Integrity attribute in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a wrong Message-Integrity. This could mean the sending device has not computed the integrity of the STUN payload before it sends out Or it has changed the payload after it has computed the integrity and hence the integrity is wrong. CUBE has not honoured this STUN message and has responded with STUN error response with a error code 400 as per RFC 5389 ipipgw LOG_STD_NO_ACTION CISCO_STUN-4-INVALID_USERNAME 4-Warning Invalid USERNAME attribute in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a wrong USERNAME attribute and does not comply with RFC 5245. CUBE has not honoured this STUN messsage and has responded with a STUN error response have ERROR-ATTRIBUTE value 400 ipipgw LOG_STD_NO_ACTION CISCO_STUN-4-INVALID_USERNAME 4-Warning Invalid USERNAME attribute in the received STUN message on UDP IP address [chars] port [dec] A STUN messages received has a wrong USERNAME attribute and does not comply with RFC 5245. CUBE has not honoured this STUN messsage and has responded with a STUN error response have ERROR-ATTRIBUTE value 400 ipipgw LOG_STD_NO_ACTION CLB-4-CLB_SLAVE_DEAD 4-Warning [chars] Slave connection is dead and is being closed. Master no longer receives updates from this Slave. - "" CLB-4-CLB_SLAVE_DEAD 4-Warning [chars] Slave connection is dead and is being closed. Master no longer receives updates from this Slave. - "" CLB-4-CLB_VERSION_MISMATCH 4-Warning [chars] Version mismatch for Cluster load-balancer feature. Master could ignore some load attributes while calculating load of a Slave. - "Upgrade to an IOS image with " "latest version of Cluster " "load-balancer feature" CLB-4-CLB_VERSION_MISMATCH 4-Warning [chars] Version mismatch for Cluster load-balancer feature. Master could ignore some load attributes while calculating load of a Slave. - "Upgrade to an IOS image with " "latest version of Cluster " "load-balancer feature" CLB-6-CLB_SLAVE_CONNECTED 6-Information [chars] Recevied new Slave connection. Master now receives update from this Slave. - "" CLB-6-CLB_SLAVE_CONNECTED 6-Information [chars] Recevied new Slave connection. Master now receives update from this Slave. - "" CLEAR_CHKPT-5-LDP 5-Notice ERRMSG_NOFLAGS - - - CLEAR_CHKPT-5-LDP 5-Notice ERRMSG_NOFLAGS - - - CLEAR_COUNTERS-5-MPLS_TE_LM 5-Notice ERRMSG_NOFLAGS - - - CLEAR_COUNTERS-5-MPLS_TE_LM 5-Notice ERRMSG_NOFLAGS - - - CLEAR_NBRS-5-LDP 5-Notice ERRMSG_NOFLAGS - - - CLEAR_NBRS-5-LDP 5-Notice ERRMSG_NOFLAGS - - - CLEAR-5-COUNTERS 5-Notice Clear counter on [chars] [chars] by [chars] The counters have been cleared on the interfaces - LOG_STD_NO_ACTION CLEAR-5-EXT_COUNT 5-Notice Clear extended [chars] counters on [chars] by [chars] The extended counters have been cleared on the interfaces - LOG_STD_NO_ACTION CLI_ADD_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - CLI_ADD_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - CLI_AGENT-1-NVGEN_ERR 1-Alert Error while processing NVGEN command: [chars] An error occurred during an NVGEN command polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-1-NVGEN_TRACEBACK 1-Alert Traceback: [chars] Traceback from NVGEN command polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BIPC_BUFFER 3-Error Error [dec] Unable to acquire a BIPC buffer for [chars] messages. A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed. polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BIPC_CONN 3-Error BIPC connection is down unable to send command: [chars] IOS cli-agent client could not connect to cli-agent using BIPC polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BIPC_ENQUEUE 3-Error Error [dec] queueing TDL message '[chars]' to send to the Shell Manager An unexpected condition has occurred when IOS attempted to queue a TDL message to send to the Shell Manager polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BIPC_INIT 3-Error Unable initialize BIPC connection to cli-agent BIPC initialization failed BIPC infra is not available polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BIPC_REMOTE 3-Error BIPC connection is down while waiting for cli-agent to reply: [chars] Connection to cli-agent is not available IOS polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-BUILD_MSG 3-Error Error [dec] building TDL message '[chars]' to send to the cli-agent: [chars] An unexpected condition has occurred while IOS is building a TDL message to send to the cli-agent polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_CTX 3-Error Unable to get [chars] for [chars] Unable to get message from the queue message received from cli-agent. There might be memory issue in IOSD. polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_DECODER 3-Error Decoder error: [chars]. Error in decoder ring string which is generated by ECI metadata file. ECI metadata files are generated from sdl file using sdl compiler in WCM. polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_ENQUEUE 3-Error Unable to enqueue received message for processing [[chars]] : [chars] Enqueue failed due multiple reason no context found TDL get error or run out of memory polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_INVALID_CTX 3-Error Invalid message cannot be processed ctx: %#X IOS recieved a message with invalid context ID. ECI cannot find the coresponding context from the table polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_MEM 3-Error Memory Error: [chars] Memory related problem polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_MODE 3-Error Submode Error [chars]: [chars] Unable to enter submode due to mode variable error polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-ECI_TIMEOUT 3-Error Maximum timeout has been reached while waiting for cli-agent to respond: [dec] seconds CLI Agent did not reply to IOS within expected timeout polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-FILE_OPEN 3-Error Failed to open [chars]: [chars] Failed to load external configuration command set polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-LOAD_FILE 3-Error Unable to load file: [chars] Unable to load data required by external configuration command set polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-MARSHAL 3-Error Error [dec] marshaling TDL message [[chars]] buffer length [dec]: [chars] An unexpected condition has occurred while IOS is marshaling TDL message to send to the cli-agent polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-MSG_DISPATCH 3-Error IOS cli-agent client message dispatcher error: [chars] cli-agent RP message dispacher error polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-NOT_EOK 3-Error Error [dec] in [chars]: [chars] The error code passed in is not EOK polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-NVGEN_CMD_LIMIT 3-Error NVGEN error: rendered command too long - truncated '[chars]' Rendered command is too long and is truncated during NVGEN polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-TDL_CREATE 3-Error Error Creating TDL message '[chars]' Could not create TDL message structure polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-3-TDL_GET 3-Error Error [dec] handling TDL GET API from TDL message [[chars]]: [chars] An unexpected condition has occurred while IOS is processing a TDL message received from the cli-agent polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-4-ECI_IGNORE_MSG 4-Warning Ignoring [chars] message: [chars] ECI in pull state and ignores the incoming mesage from cli_agent polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-4-ECI_MSG_BLK_LOW 4-Warning Not enough msg block for requesting message free msg block = [dec] ECI have runout the message block to ask for more resp msg polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-4-ECI_UNKNOWN_EVENT 4-Warning ECI recieved unknown event [dec] ECI got unknown event polaris-mgbl-infra LOG_STD_ACTION CLI_AGENT-7-ECI_DEBUG 7-Debug ECI: [chars][dec] ECI module debug polaris-mgbl-infra LOG_STD_ACTION CLIENT_CLOCK_SYNC-3-CREATEBOOL 3-Error watched boolean creation failure. bool [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-CREATEBOOL 3-Error watched boolean creation failure. bool [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTCREATE 3-Error cannot create port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTCREATE 3-Error cannot create port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTOPEN 3-Error cannot open port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTOPEN 3-Error cannot open port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTREG 3-Error cannot register port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT_CLOCK_SYNC-3-PORTREG 3-Error cannot register port [chars] due to [chars] An internal software error occurred. os "If this message recurs copy it exactly as it appears and report\n\ it to your technical support representative." CLIENT-3-LDP 3-Error ERRMSG_NOFLAGS - - - CLIENT-3-LDP 3-Error ERRMSG_NOFLAGS - - - CLNS-1-BKUPERR 1-Alert ISIS: [chars] in [hex] ndb_next [hex] ndb_prev [hex] lsp_next [hex] lsp_prev [hex] metric [hex] route type [chars] index [dec] [chars] [hex] An internal error occurred in the maintenance of the Intermediate\n\ System-to-Intermediate System ISIS backup route table. - LOG_STD_ACTION CLNS-1-BKUPERR 1-Alert ISIS: [chars] in [hex] ndb_next [hex] ndb_prev [hex] lsp_next [hex] lsp_prev [hex] metric [hex] route type [chars] index [dec] [chars] [hex] An internal error occurred in the maintenance of the Intermediate\n\ System-to-Intermediate System ISIS backup route table. - LOG_STD_ACTION CLNS-1-LINKERR 1-Alert ISIS: [chars] in [hex] lsp_next [hex] lsp_prev [hex] index [dec] ver [dec] [chars] [hex] An internal error occurred in the maintenance of Intermediate\n\ System-to-Intermediate System ISIS link-state packet LSP linkages. - LOG_STD_SH_TECH_ACTION CLNS-1-LINKERR 1-Alert ISIS: [chars] in [hex] lsp_next [hex] lsp_prev [hex] index [dec] ver [dec] [chars] [hex] An internal error occurred in the maintenance of Intermediate\n\ System-to-Intermediate System ISIS link-state packet LSP linkages. - LOG_STD_SH_TECH_ACTION CLNS-3-BADIFNUM 3-Error ISIS[chars]: Bad if number pdb [hex] idb [hex] if [hex] - - LOG_STD_SH_TECH_ACTION CLNS-3-BADIFNUM 3-Error ISIS[chars]: Bad if number pdb [hex] idb [hex] if [hex] - - LOG_STD_SH_TECH_ACTION CLNS-3-BADPACKET 3-Error [chars][chars]: [chars] [chars][chars] from [chars] [chars] An invalid packet was received from a neighboring router. - LOG_STD_ACTION CLNS-3-BADPACKET 3-Error [chars][chars]: [chars] [chars][chars] from [chars] [chars] An invalid packet was received from a neighboring router. - LOG_STD_ACTION CLNS-3-BFDCLTERR 3-Error [chars]: ISIS BFD client register fails with error[dec] - - - CLNS-3-BFDCLTERR 3-Error [chars]: ISIS BFD client register fails with error[dec] - - - CLNS-3-CASEERROR 3-Error Case statement error [dec] is out of bound ISIS encountered an internal programming error isis LOG_STD_ACTION CLNS-3-CASEERROR 3-Error Case statement error [dec] is out of bound ISIS encountered an internal programming error isis LOG_STD_ACTION CLNS-3-CKSUMERR 3-Error [chars][chars]: L[dec] LSP [chars] database checksum error restarting A hardware or software error occurred. - LOG_STD_ACTION CLNS-3-CKSUMERR 3-Error [chars][chars]: L[dec] LSP [chars] database checksum error restarting A hardware or software error occurred. - LOG_STD_ACTION CLNS-3-CRYPTOERR 3-Error [chars][chars]: Error in filling MD5 digest for [chars] PDU An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS while filling in the crypto digest for the PDU. - LOG_STD_ACTION CLNS-3-CRYPTOERR 3-Error [chars][chars]: Error in filling MD5 digest for [chars] PDU An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS while filling in the crypto digest for the PDU. - LOG_STD_ACTION CLNS-3-IFLIST 3-Error ISIS: [chars]: [chars] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-IFLIST 3-Error ISIS: [chars]: [chars] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-INTERNALERR 3-Error Internal error - [chars] An internal software error has occured isis LOG_STD_ACTION CLNS-3-INTERNALERR 3-Error Internal error - [chars] An internal software error has occured isis LOG_STD_ACTION CLNS-3-IPLIST 3-Error ISIS: [chars] [hex] [inet] [inet] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-IPLIST 3-Error ISIS: [chars] [hex] [inet] [inet] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-LSPCHAIN 3-Error [chars][chars]: non-null [chars] pointer [hex] on freed LSP index [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPCHAIN 3-Error [chars][chars]: non-null [chars] pointer [hex] on freed LSP index [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPDB 3-Error [chars][chars]: Inconsistent LSPIX entry lsp [hex] index [dec] ixentry [hex] ixentry->lsp [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_SH_TECH_ACTION CLNS-3-LSPDB 3-Error [chars][chars]: Inconsistent LSPIX entry lsp [hex] index [dec] ixentry [hex] ixentry->lsp [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_SH_TECH_ACTION CLNS-3-LSPFULL 3-Error [chars][chars]: L[dec] LSP filled to capacity [chars] A hardware or software error occurred. - LOG_STD_ACTION CLNS-3-LSPFULL 3-Error [chars][chars]: L[dec] LSP filled to capacity [chars] A hardware or software error occurred. - LOG_STD_ACTION CLNS-3-LSPFULL_OVERLOAD 3-Error [chars][chars]: Schedule L[dec] LSP to set overload bit The LSP was filled to capacity and after applying any lsp-full suppress options we still can't recover out of it. So we are going to set overload bit on the LSP - LOG_STD_ACTION CLNS-3-LSPFULL_OVERLOAD 3-Error [chars][chars]: Schedule L[dec] LSP to set overload bit The LSP was filled to capacity and after applying any lsp-full suppress options we still can't recover out of it. So we are going to set overload bit on the LSP - LOG_STD_ACTION CLNS-3-LSPGENERROR 3-Error LSPGEN cache usage is inconsistent with actual LSP space usage. \n\ Cannot add [chars] ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space. isis LOG_STD_ACTION CLNS-3-LSPGENERROR 3-Error LSPGEN cache usage is inconsistent with actual LSP space usage. \n\ Cannot add [chars] ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space. isis LOG_STD_ACTION CLNS-3-LSPGENRCTLV 3-Error LSPGEN cache space is not reserved for router capability TLV. ISIS encountered the LSPGEN cache space is not reserved for the router capability TLV. isis LOG_STD_ACTION CLNS-3-LSPGENRCTLV 3-Error LSPGEN cache space is not reserved for router capability TLV. ISIS encountered the LSPGEN cache space is not reserved for the router capability TLV. isis LOG_STD_ACTION CLNS-3-LSPGENSPACE 3-Error LSPGEN reserved space [dec] is too small. Needed [dec]. \n\ Cannot add [inet]%m ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space. isis LOG_STD_ACTION CLNS-3-LSPGENSPACE 3-Error LSPGEN reserved space [dec] is too small. Needed [dec]. \n\ Cannot add [inet]%m ISIS encountered an inconsistency between LSPGEN cache usage and the LSP space. isis LOG_STD_ACTION CLNS-3-LSPIXARRMATCH 3-Error [chars][chars]: LSPix entry [dec] mismatch with LSP [hex] LSP [chars] is [dec] entry [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPIXARRMATCH 3-Error [chars][chars]: LSPix entry [dec] mismatch with LSP [hex] LSP [chars] is [dec] entry [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPIXARRNULL 3-Error [chars][chars]: LSPix entry [dec] should be null is [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPIXARRNULL 3-Error [chars][chars]: LSPix entry [dec] should be null is [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPIXHEAD 3-Error [chars][chars]: LSPix [chars] [dec] head [hex] doesn't match first prev [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPIXHEAD 3-Error [chars][chars]: LSPix [chars] [dec] head [hex] doesn't match first prev [hex] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-LSPLIST 3-Error ISIS: [chars] [dec] index [dec] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-LSPLIST 3-Error ISIS: [chars] [dec] index [dec] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-LSPLISTERR 3-Error ISIS[chars]: LSP list traversal incomplete [chars] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-LSPLISTERR 3-Error ISIS[chars]: LSP list traversal incomplete [chars] An internal error occurred in the Intermediate System-to-Intermediate System ISIS. - LOG_STD_ACTION CLNS-3-LSPTOOBIG 3-Error [chars][chars]: L[dec] LSP [chars] size [dec] bigger than interface [chars] MTU [dec] LSP dropped A software or hardware error occurred. - LOG_STD_ACTION CLNS-3-LSPTOOBIG 3-Error [chars][chars]: L[dec] LSP [chars] size [dec] bigger than interface [chars] MTU [dec] LSP dropped A software or hardware error occurred. - LOG_STD_ACTION CLNS-3-MFIBINDERR 3-Error MFI label bind error reported for [inet]%m - [chars] MFI reported an error when ISIS tried to bind a prefix with the label isis LOG_STD_ACTION CLNS-3-MFIBINDERR 3-Error MFI label bind error reported for [inet]%m - [chars] MFI reported an error when ISIS tried to bind a prefix with the label isis LOG_STD_ACTION CLNS-3-MFIERR 3-Error ISIS MFI API error: [chars] [chars] ISIS calling MFI API failed. isis LOG_STD_ACTION CLNS-3-MFIERR 3-Error ISIS MFI API error: [chars] [chars] ISIS calling MFI API failed. isis LOG_STD_ACTION CLNS-3-NONZEROHT 3-Error [chars][chars]: Received L[dec] LSP [chars] with [dec] secs Remaining Lifetime that contain POI TLV ISIS received LSP with non-zero Remaining Lifetime that contain POI TLV isis LOG_STD_ACTION CLNS-3-NONZEROHT 3-Error [chars][chars]: Received L[dec] LSP [chars] with [dec] secs Remaining Lifetime that contain POI TLV ISIS received LSP with non-zero Remaining Lifetime that contain POI TLV isis LOG_STD_ACTION CLNS-3-NSAPES 3-Error Invalid NSAP type in ES table: [hec] for [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-3-NSAPES 3-Error Invalid NSAP type in ES table: [hec] for [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-3-NSF_CID_FORCE_FAILURE 3-Error ISIS[chars]: [chars] circuit id force to [hec] [dec] failed A circuit ID forced assignment failed. The requested\n\ circuit ID is in use on another interface. - "At the current time there is no work around. The problem should\n\ disappear following the next switchover." CLNS-3-NSF_CID_FORCE_FAILURE 3-Error ISIS[chars]: [chars] circuit id force to [hec] [dec] failed A circuit ID forced assignment failed. The requested\n\ circuit ID is in use on another interface. - "At the current time there is no work around. The problem should\n\ disappear following the next switchover." CLNS-3-NSF_CP_ADJ_CID_MISMATCH 3-Error ISIS[chars]: Checkpointed ADJ circuit id mismatch for [chars] [dec]/[dec] - - - CLNS-3-NSF_CP_ADJ_CID_MISMATCH 3-Error ISIS[chars]: Checkpointed ADJ circuit id mismatch for [chars] [dec]/[dec] - - - CLNS-3-NSF_CP_BULK_SYNC_FAIL 3-Error ISIS[chars] bulk sync failed to complete The bulk sync of ISIS adjacency and LSP data from the active to\n\ the standby RP failed to complete successfully. Any attempt by\n\ ISIS to perform a non-stop forwarding restart may be incomplete.\n\ Note that ISIS should still converge correctly. - "At the current time there is no work around. The adjacency and\n\ LSP databases should still sync up between the active and standby RPs\n\ following completion of the bulk sync. If they do not report\n\ the output from 'show isis nsf' 'show clns neighbor' and\n\ 'show isis database' on both RPs and contact the TAC." CLNS-3-NSF_CP_BULK_SYNC_FAIL 3-Error ISIS[chars] bulk sync failed to complete The bulk sync of ISIS adjacency and LSP data from the active to\n\ the standby RP failed to complete successfully. Any attempt by\n\ ISIS to perform a non-stop forwarding restart may be incomplete.\n\ Note that ISIS should still converge correctly. - "At the current time there is no work around. The adjacency and\n\ LSP databases should still sync up between the active and standby RPs\n\ following completion of the bulk sync. If they do not report\n\ the output from 'show isis nsf' 'show clns neighbor' and\n\ 'show isis database' on both RPs and contact the TAC." CLNS-3-NSF_CP_ERR 3-Error ISIS[chars]: Checkpoint send error [chars] An unrecoverable error occurred following a request to checkpoint\n\ a new or changed adjacency or LSP. - "At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC." CLNS-3-NSF_CP_ERR 3-Error ISIS[chars]: Checkpoint send error [chars] An unrecoverable error occurred following a request to checkpoint\n\ a new or changed adjacency or LSP. - "At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC." CLNS-3-NSF_CP_IDB_ENCODE_FAIL 3-Error ISIS[chars]: Interface [chars] cannot be encoded for nsf cisco Adjacency and LSP information learned from this interface cannot be checkpointed due to an interface encoding error. - "Please verify that this interface type is supported for NSF in\n\ this release. If so report the problem to the TAC." CLNS-3-NSF_CP_IDB_ENCODE_FAIL 3-Error ISIS[chars]: Interface [chars] cannot be encoded for nsf cisco Adjacency and LSP information learned from this interface cannot be checkpointed due to an interface encoding error. - "Please verify that this interface type is supported for NSF in\n\ this release. If so report the problem to the TAC." CLNS-3-NSF_CP_INIT_ERR 3-Error Checkpoint initialization error [chars] An unrecoverable error occurred during initialization of the checkpoint\n\ client. - "At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC." CLNS-3-NSF_CP_INIT_ERR 3-Error Checkpoint initialization error [chars] An unrecoverable error occurred during initialization of the checkpoint\n\ client. - "At the current time there is no work around. If the error message\n\ continues to occur report the problem to the TAC." CLNS-3-ONLIST 3-Error ISIS: entry already threaded prev [hex] next [hex] index [dec] ver [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-ONLIST 3-Error ISIS: entry already threaded prev [hex] next [hex] index [dec] ver [dec] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS. - LOG_STD_ACTION CLNS-3-PATHREG 3-Error [chars]: Get all for Path registration Failed Get all for Path registration Failed isis "This is an informational message that appears when" "Request for get all for Path Registration from ISIS failed" CLNS-3-PATHREG 3-Error [chars]: Get all for Path registration Failed Get all for Path registration Failed isis "This is an informational message that appears when" "Request for get all for Path Registration from ISIS failed" CLNS-3-PDBMODE_ADJDB_INCORRECT 3-Error [chars][chars]: Adjacency DB should[chars] be [hex] is [hex] Adjacency database must match process and does not. isis LOG_STD_ACTION CLNS-3-PDBMODE_ADJDB_INCORRECT 3-Error [chars][chars]: Adjacency DB should[chars] be [hex] is [hex] Adjacency database must match process and does not. isis LOG_STD_ACTION CLNS-3-PDBMODE_ADJDB_NOTEMPTY 3-Error [chars][chars]: Adjacency DB should be empty before deleting and is not Adjacency database must be empty before deleting and is not. isis show clns neighbors CLNS-3-PDBMODE_ADJDB_NOTEMPTY 3-Error [chars][chars]: Adjacency DB should be empty before deleting and is not Adjacency database must be empty before deleting and is not. isis show clns neighbors CLNS-3-PDBMODE_TRANS_INVALID 3-Error [chars][chars]: Transition target for pdb mode is invalid: \n\ current [dec] target [dec] ISIS process received request to transition to invalid state isis LOG_STD_ACTION CLNS-3-PDBMODE_TRANS_INVALID 3-Error [chars][chars]: Transition target for pdb mode is invalid: \n\ current [dec] target [dec] ISIS process received request to transition to invalid state isis LOG_STD_ACTION CLNS-3-SIDERR 3-Error ISIS SID conflict detected for [inet]%m There is more than one node advertising the same prefix.\n\ But the prefix SID is different. isis LOG_STD_ACTION CLNS-3-SIDERR 3-Error ISIS SID conflict detected for [inet]%m There is more than one node advertising the same prefix.\n\ But the prefix SID is different. isis LOG_STD_ACTION CLNS-3-TENT 3-Error [chars][chars]: [chars] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS - LOG_STD_ACTION CLNS-3-TENT 3-Error [chars][chars]: [chars] An internal error occurred in the Intermediate System-to-Intermediate\n\ System ISIS - LOG_STD_ACTION CLNS-3-TERRRERR 3-Error [chars] called on standby An ISIS RRR support routine has been incorrectly called on standby isis LOG_STD_ACTION CLNS-3-TERRRERR 3-Error [chars] called on standby An ISIS RRR support routine has been incorrectly called on standby isis LOG_STD_ACTION CLNS-3-TEXT 3-Error [chars] Used to display different types of Error messages isis "This is an informational message that appears when" "there is an exception" CLNS-3-TEXT 3-Error [chars] Used to display different types of Error messages isis "This is an informational message that appears when" "there is an exception" CLNS-3-VLANRANGEERR 3-Error [chars]: invalid vlan range received begin [dec] end [dec] step [dec] An invalid vlan range has been received in lsp - LOG_STD_ACTION CLNS-3-VLANRANGEERR 3-Error [chars]: invalid vlan range received begin [dec] end [dec] step [dec] An invalid vlan range has been received in lsp - LOG_STD_ACTION CLNS-4-AREALOST 4-Warning [chars][chars]: Too many IS-IS areas--can\'t route to area [chars] - - "Reconfigure the network so that the area has fewer area addresses or\n\ split the area into multiple areas." CLNS-4-AREALOST 4-Warning [chars][chars]: Too many IS-IS areas--can\'t route to area [chars] - - "Reconfigure the network so that the area has fewer area addresses or\n\ split the area into multiple areas." CLNS-4-AUTH_FAIL 4-Warning [chars]: [chars][chars] authentication failed An ISIS packetIIH CSNP PSNP or LSP was received and did not - "If the error persists check the originating router for matching " "authentication mode and password." CLNS-4-AUTH_FAIL 4-Warning [chars]: [chars][chars] authentication failed An ISIS packetIIH CSNP PSNP or LSP was received and did not - "If the error persists check the originating router for matching " "authentication mode and password." CLNS-4-BADINTFCLNSMTU 4-Warning [chars] Invalid interface clns MTU [dec] This message occurs if the interface MTU becomes unusable\n\ while ISIS is running on the interface. This condition\n\ maybe temporary and recoverable. - LOG_STD_ACTION CLNS-4-BADINTFCLNSMTU 4-Warning [chars] Invalid interface clns MTU [dec] This message occurs if the interface MTU becomes unusable\n\ while ISIS is running on the interface. This condition\n\ maybe temporary and recoverable. - LOG_STD_ACTION CLNS-4-BADIPMSK 4-Warning ISIS[chars]: Inconsistent ip prefix and mask[inet]%#m in ISIS LSP: The system received a link-state packet LSP which contained a - LOG_STD_SH_TECH_ACTION CLNS-4-BADIPMSK 4-Warning ISIS[chars]: Inconsistent ip prefix and mask[inet]%#m in ISIS LSP: The system received a link-state packet LSP which contained a - LOG_STD_SH_TECH_ACTION CLNS-4-CORRUPTLIFETIME 4-Warning [chars][chars]: possible corrupted lifetime [dec] secs for L[dec] lsp [chars] from SNPA [chars] detected ISIS received the remaining lifetime value which is less than ZeroAgeLifetime 60 secs - LOG_STD_ACTION CLNS-4-CORRUPTLIFETIME 4-Warning [chars][chars]: possible corrupted lifetime [dec] secs for L[dec] lsp [chars] from SNPA [chars] detected ISIS received the remaining lifetime value which is less than ZeroAgeLifetime 60 secs - LOG_STD_ACTION CLNS-4-DISALLOWED_TLV_IN_PURGE 4-Warning Received disallowed TLV [dec] in Purge LSP ISIS received a Purge LSP containing a disallowed TLV isis "Check ISIS routing protocol for RFC6233 compliant" CLNS-4-DISALLOWED_TLV_IN_PURGE 4-Warning Received disallowed TLV [dec] in Purge LSP ISIS received a Purge LSP containing a disallowed TLV isis "Check ISIS routing protocol for RFC6233 compliant" CLNS-4-DUPSNPA 4-Warning [chars][chars]: Duplicate SNPA [chars] detected This may be a configuration error. - "One of the duplicate SNPA addresses needs to be corrected." CLNS-4-DUPSNPA 4-Warning [chars][chars]: Duplicate SNPA [chars] detected This may be a configuration error. - "One of the duplicate SNPA addresses needs to be corrected." CLNS-4-DUPSYSTEM 4-Warning [chars][chars]: possible duplicate system ID [chars] detected This is a configuration error. - "One of the duplicate IDs needs to be corrected." CLNS-4-DUPSYSTEM 4-Warning [chars][chars]: possible duplicate system ID [chars] detected This is a configuration error. - "One of the duplicate IDs needs to be corrected." CLNS-4-EDATFAIL 4-Warning Encapsulation failed dst= [chars] This message can occur when an interface is down and a static\n\ neighbor entry exists in the system's CLNS routing table. If this is\n\ not the case the message indicates an internal software error. - "Check the interface. If the interface is not down and no static\n\ neighbor entry exists for that interface call your technical support\n\ representative for assistance." CLNS-4-EDATFAIL 4-Warning Encapsulation failed dst= [chars] This message can occur when an interface is down and a static\n\ neighbor entry exists in the system's CLNS routing table. If this is\n\ not the case the message indicates an internal software error. - "Check the interface. If the interface is not down and no static\n\ neighbor entry exists for that interface call your technical support\n\ representative for assistance." CLNS-4-FLEX_CFG_OVER_LIMIT 4-Warning Number of flex algos reach the limit Number of configured flex-algos reach the limit and configuration of addtional flex-algos is not accepted in order to avoid known issues with highly scaled configuration. Limit will be removed in one of the future release. isis "Accept configuration limit." CLNS-4-FLEX_CFG_OVER_LIMIT 4-Warning Number of flex algos reach the limit Number of configured flex-algos reach the limit and configuration of addtional flex-algos is not accepted in order to avoid known issues with highly scaled configuration. Limit will be removed in one of the future release. isis "Accept configuration limit." CLNS-4-GR_FAIL 4-Warning [chars] failed: Invalid PDB GR Sub-block for ISIS-[chars] IS-IS Graceful Reload was not completed due to invalid PDB GR Sub-Block. - "If the error persists check the IS-IS configuration for that instance" CLNS-4-GR_FAIL 4-Warning [chars] failed: Invalid PDB GR Sub-block for ISIS-[chars] IS-IS Graceful Reload was not completed due to invalid PDB GR Sub-Block. - "If the error persists check the IS-IS configuration for that instance" CLNS-4-GR_INVALID_CLIENT 4-Warning GR_INFRA failed to assign a valie client ID to IS-IS IS-IS received invalid client ID from GR_INFRA - "If the error persists restart the IS-IS process" CLNS-4-GR_INVALID_CLIENT 4-Warning GR_INFRA failed to assign a valie client ID to IS-IS IS-IS received invalid client ID from GR_INFRA - "If the error persists restart the IS-IS process" CLNS-4-GR_REG_FAIL 4-Warning Failed to register with GR_INFRA rc=[dec] IS-IS failed to register with GR_INFRA - "If the error persists restart the IS-IS process" CLNS-4-GR_REG_FAIL 4-Warning Failed to register with GR_INFRA rc=[dec] IS-IS failed to register with GR_INFRA - "If the error persists restart the IS-IS process" CLNS-4-INVALIDKCKEYID 4-Warning Key ID [dec] in key chain [chars] is invalid They Key ID configured in the key chain is out of range for ISIS. This may happen because the key chain allows Key ID values outside of the range which is acceptable for ISIS. isis "Configure a new security association with a Key ID that is in " "the range 1-65535" CLNS-4-INVALIDKCKEYID 4-Warning Key ID [dec] in key chain [chars] is invalid They Key ID configured in the key chain is out of range for ISIS. This may happen because the key chain allows Key ID values outside of the range which is acceptable for ISIS. isis "Configure a new security association with a Key ID that is in " "the range 1-65535" CLNS-4-INVALIDKCNAME 4-Warning Key chain name [chars] is invalid The key-chain name configured under ISIS does not match global key chain configuration. isis "Fix configuration" CLNS-4-INVALIDKCNAME 4-Warning Key chain name [chars] is invalid The key-chain name configured under ISIS does not match global key chain configuration. isis "Fix configuration" CLNS-4-INVALIDKEY 4-Warning Key ID [dec] [chars]on interface [chars] The ID is not found in the configured key chain isis "Configure a new security association with the Key ID" CLNS-4-INVALIDKEY 4-Warning Key ID [dec] [chars]on interface [chars] The ID is not found in the configured key chain isis "Configure a new security association with the Key ID" CLNS-4-LSP_MAXSEQ 4-Warning [chars][chars]: attempt to exceed LSP maximum sequence number for LSP [chars] Attempt was made to exceed maximum sequence number for an LSP. - "Protocol will shutdown for max-lsp-lifetime + 1 minute.\n\ This is a very unlikely natural occurrence.\n\ Investigate to find the source of any out of order reception\n\ generation or incrementing of this LSP's sequence number." CLNS-4-LSP_MAXSEQ 4-Warning [chars][chars]: attempt to exceed LSP maximum sequence number for LSP [chars] Attempt was made to exceed maximum sequence number for an LSP. - "Protocol will shutdown for max-lsp-lifetime + 1 minute.\n\ This is a very unlikely natural occurrence.\n\ Investigate to find the source of any out of order reception\n\ generation or incrementing of this LSP's sequence number." CLNS-4-LSPCKSUM 4-Warning [chars][chars]: Bad L[dec] [chars] LSP [chars] checksum %04x received on [chars] length [dec] should be %04x bad count [dec] - - "If the error is in a neighboring router's memory the problem\n\ will correct itself within 15 minutes. That router will detect\n\ its internal error and regenerate the corrupted data. This\n\ case is usually indicated by a single LSP ID appearing\n\ repeatedly in these messages. The same LSP ID might appear in\n\ this message on other routers as well.\n\\n\ If data-link corruption has caused the error check the link\n\ for errors and deal with them appropriately. This case is\n\ usually indicated by a number of different LSP IDs appearing\n\ in these messages." CLNS-4-LSPCKSUM 4-Warning [chars][chars]: Bad L[dec] [chars] LSP [chars] checksum %04x received on [chars] length [dec] should be %04x bad count [dec] - - "If the error is in a neighboring router's memory the problem\n\ will correct itself within 15 minutes. That router will detect\n\ its internal error and regenerate the corrupted data. This\n\ case is usually indicated by a single LSP ID appearing\n\ repeatedly in these messages. The same LSP ID might appear in\n\ this message on other routers as well.\n\\n\ If data-link corruption has caused the error check the link\n\ for errors and deal with them appropriately. This case is\n\ usually indicated by a number of different LSP IDs appearing\n\ in these messages." CLNS-4-NOVALIDKEY 4-Warning No valid authentication key is available - isis "Configure a new key" CLNS-4-NOVALIDKEY 4-Warning No valid authentication key is available - isis "Configure a new key" CLNS-4-NSAPIS 4-Warning Invalid NSAP type in IS table: [hec] [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-4-NSAPIS 4-Warning Invalid NSAP type in IS table: [hec] [dec] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-4-OTV_OVERLAY_SITE_ID_MISMATCH 4-Warning [chars] Site id [chars] from neighbor [chars] does not match site id [chars] received in site hellos. A neighbor in the same site is sending a different site ID in its overlay hellos than in its site hellos - "Verify site id configuration and/or site connecetivity " CLNS-4-OTV_OVERLAY_SITE_ID_MISMATCH 4-Warning [chars] Site id [chars] from neighbor [chars] does not match site id [chars] received in site hellos. A neighbor in the same site is sending a different site ID in its overlay hellos than in its site hellos - "Verify site id configuration and/or site connecetivity " CLNS-4-OTV_SITE_FAIL 4-Warning [chars]: [chars] site info update failed An ISIS packetIIH CSNP PSNP was received and failed to - "If the error persists check the originating router " CLNS-4-OTV_SITE_FAIL 4-Warning [chars]: [chars] site info update failed An ISIS packetIIH CSNP PSNP was received and failed to - "If the error persists check the originating router " CLNS-4-OTV_SITE_ID_MISMATCH 4-Warning Site id [chars] from neighbor [chars] does not match local site id OTV Site ID received from a neighbor in the same site has a different site id indicating a misconfiguration error. - "Verify site id configuration and/or site connecetivity " CLNS-4-OTV_SITE_ID_MISMATCH 4-Warning Site id [chars] from neighbor [chars] does not match local site id OTV Site ID received from a neighbor in the same site has a different site id indicating a misconfiguration error. - "Verify site id configuration and/or site connecetivity " CLNS-4-REDIRECT 4-Warning Redirect found for non-route entry dst= [chars] next-hop= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-4-REDIRECT 4-Warning Redirect found for non-route entry dst= [chars] next-hop= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION CLNS-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" CLNS-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" CLNS-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" CLNS-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" CLNS-4-SIDRANGE 4-Warning [chars] [dec] for [inet]%m is out of SRGB range [dec] via [inet] ISIS tried to bind a label to a prefix that is out of SRGB range isis LOG_STD_ACTION CLNS-4-SIDRANGE 4-Warning [chars] [dec] for [inet]%m is out of SRGB range [dec] via [inet] ISIS tried to bind a label to a prefix that is out of SRGB range isis LOG_STD_ACTION CLNS-5-ADJCHANGE 5-Notice [chars][chars]: Adjacency to [chars] [chars] [chars] [chars] - - "This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated." CLNS-5-ADJCHANGE 5-Notice [chars][chars]: Adjacency to [chars] [chars] [chars] [chars] - - "This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated." CLNS-5-ADJCLEAR 5-Notice [chars][chars]: All [chars]adjacencies cleared - - "This informational message appears as a normal side effect\n\ of appropriate console or configuration commands." CLNS-5-ADJCLEAR 5-Notice [chars][chars]: All [chars]adjacencies cleared - - "This informational message appears as a normal side effect\n\ of appropriate console or configuration commands." CLNS-5-EXPIREDKEY 5-Notice Packet [chars] with expired Key ID [dec]. The Key ID in use has a lifetime and the system time is not within that lifetime isis "Configure a new key" CLNS-5-EXPIREDKEY 5-Notice Packet [chars] with expired Key ID [dec]. The Key ID in use has a lifetime and the system time is not within that lifetime isis "Configure a new key" CLNS-5-FADJCHANGE 5-Notice [chars][chars]: MPLS TE Forwarding Adjacency to [chars] [chars] [chars] [chars] - - "This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated." CLNS-5-FADJCHANGE 5-Notice [chars][chars]: MPLS TE Forwarding Adjacency to [chars] [chars] [chars] [chars] - - "This informational message normally appears as\n\ routers and links go up or down. However unexpected adjacency loss might\n\ indicate high error rates or high packet loss in the network and should\n\ be investigated." CLNS-5-FLEX_ALGO_DISABLED_NO_DEFN 5-Notice [chars]: Flex-Algo [dec] is disabled for Level-[dec] no best definition available Flex algorithm is disabled because best definition is not available isis "This is an informational message that appears when" "flex-algo is disabled because of no best definition" CLNS-5-FLEX_ALGO_DISABLED_NO_DEFN 5-Notice [chars]: Flex-Algo [dec] is disabled for Level-[dec] no best definition available Flex algorithm is disabled because best definition is not available isis "This is an informational message that appears when" "flex-algo is disabled because of no best definition" CLNS-5-FLEX_DEFN_CHANGE 5-Notice [chars]: Flex-Algo [dec] Level-[dec] definition changed priority [dec] source System-ID [chars] Flex algorithm definition changed isis "This is an informational message that appears when" "flex-algo definition changes" CLNS-5-FLEX_DEFN_CHANGE 5-Notice [chars]: Flex-Algo [dec] Level-[dec] definition changed priority [dec] source System-ID [chars] Flex algorithm definition changed isis "This is an informational message that appears when" "flex-algo definition changes" CLNS-5-FLEX_DEFN_ENABLE_DISABLE 5-Notice [chars]: Flex-Algo [dec] is [chars] for Level-[dec] Flex algorithm enabled or disabled isis "This is an informational message that appears when" "flex-algo is enabled or disabled" CLNS-5-FLEX_DEFN_ENABLE_DISABLE 5-Notice [chars]: Flex-Algo [dec] is [chars] for Level-[dec] Flex algorithm enabled or disabled isis "This is an informational message that appears when" "flex-algo is enabled or disabled" CLNS-5-NOCRYPTOALG 5-Notice Key ID [dec] in key chain [chars] does not have a cryptographic algorithm ISIS has been configured to use cryptographic authentication however an algorithm has not been configured isis "Configure a cryptographic-algorithm for the security association" CLNS-5-NOCRYPTOALG 5-Notice Key ID [dec] in key chain [chars] does not have a cryptographic algorithm ISIS has been configured to use cryptographic authentication however an algorithm has not been configured isis "Configure a cryptographic-algorithm for the security association" CLNS-5-NOKEY 5-Notice Key ID [dec] in key chain [chars] does not have a key ISIS has been configured to use cryptographic authentication however an key password has not been configured isis "Configure a key for the security association" CLNS-5-NOKEY 5-Notice Key ID [dec] in key chain [chars] does not have a key ISIS has been configured to use cryptographic authentication however an key password has not been configured isis "Configure a key for the security association" CLNS-5-NSF_ISSU_NEGO_FAIL 5-Notice ISIS NSF cancelled - ISSU negotiation failed for NSF CISCO ISIS cancelled the NSF restart since ISSU negotiation failed\n\ in Cisco mode. - "Review the output of 'show issu negotiated version' command" CLNS-5-NSF_ISSU_NEGO_FAIL 5-Notice ISIS NSF cancelled - ISSU negotiation failed for NSF CISCO ISIS cancelled the NSF restart since ISSU negotiation failed\n\ in Cisco mode. - "Review the output of 'show issu negotiated version' command" CLNS-5-NSF_NO_RP_SIGNAL 5-Notice ISIS[chars] NSF cancelled - 'nsf interval' expiration pending ISIS cancelled the NSF restart since either the active\n\ or standby RP had not been up long enough. In Cisco mode\n\ the active RP must signal that it has been up for a minimum\n\ of 'nsf interval' seconds. For IETF mode the standby RP must\n\ be up for a minimum of 'nsf interval' seconds. - "Review the setting of the 'nsf interval' command" CLNS-5-NSF_NO_RP_SIGNAL 5-Notice ISIS[chars] NSF cancelled - 'nsf interval' expiration pending ISIS cancelled the NSF restart since either the active\n\ or standby RP had not been up long enough. In Cisco mode\n\ the active RP must signal that it has been up for a minimum\n\ of 'nsf interval' seconds. For IETF mode the standby RP must\n\ be up for a minimum of 'nsf interval' seconds. - "Review the setting of the 'nsf interval' command" CLNS-5-NSF_RESTART 5-Notice ISIS[chars] NSF completion ISIS performed an NSF restart - "This informational message appears as a normal side effect\n\ of a restart performed while NSF is enabled" CLNS-5-NSF_RESTART 5-Notice ISIS[chars] NSF completion ISIS performed an NSF restart - "This informational message appears as a normal side effect\n\ of a restart performed while NSF is enabled" CLNS-5-NSF_STATUS 5-Notice [chars][chars] NSF [chars] This message used to print NSF status logs - "This informational message appears while NSF is enabled" CLNS-5-NSF_STATUS 5-Notice [chars][chars] NSF [chars] This message used to print NSF status logs - "This informational message appears while NSF is enabled" CLNS-6-DFT_OPT 6-Information Protocol timers for fast convergence are [chars]. Routing-default-optimize state isis LOG_STD_ACTION CLNS-6-DFT_OPT 6-Information Protocol timers for fast convergence are [chars]. Routing-default-optimize state isis LOG_STD_ACTION CLNS-7-DEBUG_TRACEBACK 7-Debug Debug: [chars] Debug information. - "No action required" CLNS-7-DEBUG_TRACEBACK 7-Debug Debug: [chars] Debug information. - "No action required" CLNS-7-DEBUGMSG 7-Debug [chars]: %08x %08x %08x %08x %08x %08x Internal use only clns "Should not be seen in the field" CLNS-7-DEBUGMSG 7-Debug [chars]: %08x %08x %08x %08x %08x %08x Internal use only clns "Should not be seen in the field" CLNT_REG-7-LDP 7-Debug ERRMSG_NOFLAGS - - - CLNT_REG-7-LDP 7-Debug ERRMSG_NOFLAGS - - - CLOCK_RECOVERY-4-CLOCK_FAILED 4-Warning [chars] on module [dec]/[dec] failed This message indicates that an active recovered or enhanced clock has failed - LOG_STD_NO_ACTION CLOCK_RECOVERY-6-CLOCK_ACTIVE 6-Information [chars] on module [dec]/[dec] is now active This message indicates that a recovered or enhanced clock has become active - LOG_STD_NO_ACTION CLOCK-3-HW_CAL_INVALID 3-Error Hardware Calendar RTC Error. The hardware calendar contains an invalid date. The accepted range\n\ is from 1993 to 2035. me3600-me3800-sys "To correct the invalid date use the calendar set\n\ command and the clock read-calendar command.\n" CLS_ACC-2-CONFIG_NV_DATA 2-Critical Express setup parameter committed. Default port role will be applied After express setup parameters are committed switch becomes a configured switch. The default port roles are automatically applied to all ports at this moment. The port role configurations may be manually modified after this point. firmware LOG_NO_ACTION CLS_ACC-2-MODE_ENTERED 2-Critical Entering consoleless access mode [chars] Switch enters one of the consoleless access modes firmware LOG_NO_ACTION CLS_ACC-2-MODE_EXITED 2-Critical Complete consoleless access from mode [chars] Switch exits from one of the consoleless access modes firmware LOG_NO_ACTION CLS_ACC-2-NO_PROCESS 2-Critical Process creation failure Failed to create process to execute consoleless access firmware LOG_NO_ACTION CLS_ACC-2-SETUP_BTN_PRS 2-Critical [chars] Pressing the switch setup button will lead an unconfigured switch to go to express setup mode. It will not have any effect on an already configured switch. Pressing the setup button for more than 5 seconds will lead a configured switch to go to direct management mode or lead an unconfigured switch to go to express setup mode firmware LOG_NO_ACTION CLS_ACC-3-CONFIG_ERROR 3-Error [chars] Not able to correctly configure the switch for consoleless access Can't go to access mode firmware LOG_NO_ACTION CLS_ACC-3-NO_ACC_INTF 3-Error Failed to find a free interface as consoleless access interface or failed to retrieve the access interface information Not able to find a free interface which is fit to serve as management interface for consoleless access firmware LOG_NO_ACTION CLS_ACC-3-NOMEMORY 3-Error [chars] Memory allocation failure for executing consoleless access switch configuration commands firmware LOG_STD_ACTION CLS_ACC-3-NOSOCKET 3-Error Fail to create DNS socket for consoleless access Socket creation failure switch is not able to go into consoleless access mode. Abort. firmware LOG_NO_ACTION CLS_ACC-3-UNABLE_TO_RESET_CONFIG 3-Error [chars] The system is unable to reset the configuration firmware LOG_STD_ACTION CLS_ACC-3-VLAN_CREATE_FAIL 3-Error Failed to allocate a free vlan as consoleless access vlan use default mamagement vlan Not able to find a free vlan in the range of 2-1000 to server as management vlan for consoleless access firmware LOG_NO_ACTION CLS_ACC-4-NO_HTTP_PAGE 4-Warning Failed to locate HTTP page for the consoleless access mode Not able to locate the HTTP page corresponding to the access mode. Page is not on flash firmware LOG_NO_ACTION CLS_ACC-4-UNEXPECTEDEVENT 4-Warning Switch does not support or not ready for consoleless access mode Switch either does not support or is not ready to enter the requested consoleless access mode firmware LOG_NO_ACTION CLS_ACC-5-CLRCFG 5-Notice User cleared switch configurations under recovery mode Under consoleless access mode user takes an action to reset switch configuration to factory default. firmware LOG_NO_ACTION CLS_ACC-5-RSTIMG 5-Notice User reset switch image to factory default image under recovery mode Under consoleless access mode user takes an action to reset switch image to factory default. firmware LOG_NO_ACTION CLS_ACC-7-ACC_INTF 7-Debug Selected management interface: [chars] interface number: [dec] Selected an interface as consoleless access interface firmware LOG_NO_ACTION CLS_ACC-7-ACC_VLAN 7-Debug Selected vlan [dec] for consoleless access A new vlan is created to only include the management interface Vlan creation successful firmware LOG_NO_ACTION CLS_ACC-7-CONFIG 7-Debug Save access intf config: if: [chars] port num: [dec] vlan [dec] admin-down?:[dec] Save interface configurations these configurations will be restored when consoleless access exits and returns the interface firmware LOG_NO_ACTION CLS_ACC-7-CONFIG_SUCCESS 7-Debug [chars] Consoleless access mgmt interface successfully configured or its original configuration successfully restored firmware LOG_NO_ACTION CLS-3-BOGUSOP 3-Error Unknown CLS verb for [chars] context DlcOpcodeT=%04x A bad opcode was generated by the DLC for the STN or CEP. - LOG_STD_ACTION CLS-3-CLSFAIL 3-Error CLS: Assertion failed: [chars] A software or hardware error occurred. - LOG_STD_ACTION CLS-3-CLSMSG 3-Error [chars] A software error detected while manipulating CLSIMsg objects. - LOG_STD_ACTION CLSDR-3-ERRRTN 3-Error [chars] failed error 0x[hec] - - "Refer to CLSI software documentation for more information about this\n\ error. Report this error to your technical support representative." CLSDR-3-INCORRECTPORT 3-Error Incorrect port pointer in USapId - - LOG_STD_ACTION CLSDR-3-MSGERR 3-Error [chars] couldn't get a message - - LOG_STD_ACTION CLSDR-3-NOCEP 3-Error Cannot found cep in free pool A software or hardware error occurred. - LOG_STD_ACTION CLSDR-3-NOCLSSERVER 3-Error unable to start the Server process Could not start the CLSDRIVER process possibly due to a resource\n\ problem. The subsystem using CLSDRIVER does not work. - - CLSDR-3-NODLUCREATE 3-Error Cannot create DLU for this type [dec] - - LOG_STD_ACTION CLSDR-3-NOINIT 3-Error CLSDRIVER not initialized A CLSDRIVER initialization failed earlier. Trying to use the driver\n\ now results in an error condition. - - CLSDR-3-NOPORTCREATE 3-Error Cannot create PORT structure The CLSDRIVER cannot enable this port for processing. - "Try rebooting the router. " LOG_STD_ACTION CLSDR-3-NOREMOVECEP 3-Error RemoveCep : Cep 0x[hec] not on list - - LOG_STD_ACTION CLSDR-3-NOREMOVEPORT 3-Error RemovePort: port 0x[hec] not on list - - LOG_STD_ACTION CLSDR-3-WRONGMSG 3-Error Should never be here cls message type unknown 0x[hec] The CLS message type is unknown to the destination logical unit\n\ DLU. - LOG_STD_ACTION CLUE-3-CHECKSUM_ERROR 3-Error CLUE record checksum error in record id [dec] record starting address [hex] new checksum [hex] previous checksum [hex] CLUE record stored in the CLUE memory had a bad checksum. The \n\ CLUE record was modified by a CLUE client but not committed or by \n\ unknown memory corruption. The CLUE record cannot be accessed. clue "Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit." CLUE-3-CLIENT_REGISTRY_FULL 3-Error Maximum of [dec] CLUE clients registered. Cannot register callback [hex] - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-COMMIT_FAILED 3-Error CLUE cannot commit record id [dec] The given CLUE record was not committed in the CLUE storage memory.\n\ CLUE record was not allocated by the CLUE client before committing or \n\ there was an error in the internal CLUE record index table. The CLUE \n\ record cannot be accessed. clue "Internal CLUE software may automatically rectify the error. However \n\ if the error persists copy the error message exactly as it appears and \n\ report it to your technical support representative." CLUE-3-EOR_CORRUPT 3-Error CLUE record corruption in end of record field record id [dec] record starting address [hex] CLUE record's end of record delimiter was corrupted in the CLUE \n\ storage memory. The CLUE record was over-written by the\n\ previous CLUE record or by an unknown memory corruption. The \n\ CLUE record cannot be accessed. clue "Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit." CLUE-3-INDEX_BUILD_FAIL 3-Error Failed to build CLUE internal record index due to [chars] CLUE expected existence of valid CLUE records in CLUE storage when \n\ building internal record index table. CLUE will fail to build the index\n\ table when CLUE storage does not exist or any CLUE record within the\n\ CLUE storage has some data corruption. CLUE service will not be \n\ available and any data in the CLUE storage cannot be accessed. clue "Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit." CLUE-3-INIT_ERROR 3-Error Failed to initialise the reserved memory for new CLUE context due to [chars] - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-INTERNAL_SW_ERROR 3-Error [chars] Internal Compact Local Unit Exchange CLUE software error reported clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-INVALID_AREA 3-Error Either address [hex] or size [dec] reserved for CLUE storage area is invalid - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-INVALID_REC_DATA_SIZE 3-Error CLUE record size [dec] is invalid to allocate CLUE record [dec] - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-INVALID_REC_ID 3-Error Invalid CLUE record id [dec] has been received so CLUE cannot [chars] it - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-NO_SIGNATURE 3-Error CLUE cannot [chars] record id [dec] The given CLUE record was not serviced. CLUE storage was not \n\ available or the CLUE storage signature was invalid. clue "Internal CLUE software may automatically rectify the error. However \n\ if the error persists copy the error message exactly as it appears and \n\ report it to your technical support representative." CLUE-3-NOT_ENOUGH_CLUE_STORAGE 3-Error CLUE storage has not enough space to allocate record id [dec] and data size [dec] - clue "Copy the error message exactly as it appears attach outputs from the \n\ show clue and show tech commands and report the error to your technical \n\ support representative." CLUE-3-NOT_ENOUGH_MEMORY 3-Error [dec]-bytes of local memory has not enough space left to reserve [dec]-bytes of CLUE storage Local memory was not big enough to reserve the required Compact Local \n\ Unit Exchange CLUE storage space. clue "Add more local memory." CLUE-3-SOR_CORRUPT 3-Error CLUE record corruption in start of record field record id [dec] record starting address [hex] CLUE record's start of record delimiter was corrupted in the CLUE \n\ storage memory. The CLUE record was over-written by the\n\ previous CLUE record or by an unknown memory corruption. The \n\ CLUE record cannot be accessed. clue "Internal CLUE Client software may automatically rectify the error. \n\ However if the error persists reload the unit." CM_MONITOR-5-DNS_KILL 5-Notice Terminating DNS process A hardware or software error occurred. - LOG_STD_ACTION CM_MONITOR-5-DNS_RESP 5-Notice Sending DNS response to [inet] request was for [inet] - - - CM_MONITOR-5-DNS_START 5-Notice Starting DNS process A hardware or software error occurred. - LOG_STD_ACTION CM_REDUC_MODE-4-BM_ATTR_NOT_MAINTAIN 4-Warning Attribute masks are not maintained when entering battery mode. CM MAC addr <[enet]> Attribute masks are not maintained when entering battery mode \n cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-BM_NO_AVAILABLE_DBG 4-Warning Entering battery mode failed since no available RBG. CM MAC addr <[enet]> Entering battery mode failed since no available RBG \n cbr-application "Please inspect the configuration file and configured " "available RBG" CM_REDUC_MODE-4-BM_OPERATION_EXCEED_MAX_COUNT 4-Warning Enter into/exit BM mode failed for CM MAC addr <[enet]> There maybe resource limitation which induce BM operation failure.\n cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-BM_ORG_RCC_INAVAILABLE 4-Warning Exiting battery mode failed since original rcc unavailable. CM MAC addr <[enet]> Exiting battery mode failed since original rcc unavailable \n cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-DBC_REJECT_CAUSE_CM_OFFLINE 4-Warning CM [enet] forcely offline because the operation failed as DBC rejected the invalid request DBC client [dec] DBC failed to change CM BG because the operation was rejected as one invalid request. That cause the CM was not permitted to register again to the original BG. Mark CM offline to avoid CM stuck in reduce mode cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-EM_ATTR_NOT_MAINTAIN 4-Warning Attribute masks are not maintained when entering EM mode. CM MAC addr <[enet]> Attribute masks are not maintained when entering EM mode \n cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-EM_INVALID_EM_REQ 4-Warning Receive an invalid EM request message from CM MAC addr <[enet]> request power mode [dec]. Receive invalid requested power mode from CM\n cbr-application LOG_STD_NO_ACTION CM_REDUC_MODE-4-EM_NO_AVAILABLE_DBG 4-Warning Entering EM mode failed since no available RBG. CM MAC addr <[enet]> Entering EM mode failed since no available RBG \n cbr-application "Please inspect the configuration file" CM_SYNC-3-NO_BUFFER 3-Error Unable to transmit message type [dec] from [chars] A transmit error occurred while sending msg to other CPU due to non-availability of buffer - LOG_STD_ACTION CM_SYNC-3-TRANSMIT_ERROR 3-Error Unable to transmit message type [dec] from [chars] A transmit error occurred while sending msg to other CPU due to msg translation - LOG_STD_ACTION CM622_CM155-4-ATMCLKINT 4-Warning [dec]/[dec] ATM Clock Internal Set on [dec]/[dec] too CM155 ATM Clock Internal is enabled for the other channel \ on the same framer too the framer defines one bit for \ both channels. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-FRMROP 4-Warning Error: [dec]/[dec] [chars] value=0x%04x Linecard ATM driver framer operation errors. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-FWCKSUM 4-Warning Port [dec]: [chars] SAR firmware selftest failure expected 0x%04x obtained 0x%04x Linecard ATM SAR firmware checksum errors. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-OP 4-Warning Error: [dec]/[dec] [chars] Linecard ATM driver general operation errors. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-RPCMD 4-Warning [dec]/[dec] [chars] command error: [chars] Linecard ATM driver handles RP command errors. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-RXSARIND 4-Warning [dec]/[dec] RX SAR doing [chars] error: [chars] indication=0x%08x 0x%08x 0x%08x Linecard ATM driver RX SAR indication errors. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-SAROP 4-Warning Port [dec]: [chars] SAR doing [chars] error: [chars] Linecard ATM driver SAR operation error. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-TXSARIND 4-Warning Port [dec]: TX SAR [chars] command error: [chars] indication=0x%08x Linecard ATM driver TX SAR indication error. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-VCCLOSE 4-Warning [dec]/[dec] VC:[dec] is close pending The VC is in the TX SAR close pending state. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-VCCMD 4-Warning [dec]/[dec] VC:[dec] [chars] error cause: [chars] CM622/CM155 ATM SAR VC operation error. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CM622_CM155-4-VCTYPE 4-Warning [dec]/[dec] VC:[dec] unsupported vc encapsulation type=[dec] CM622/CM155 ATM SAR VC operation error. gsr "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CMANCC-2-CRASHDUMP 2-Critical Fatal error calling crashdump error: [dec] [chars] A fatal condition has occurred causing IOS to crashdump. IOS will\n\ be restarted automatically. iosxe-chassismgr LOG_STD_ACTION CMANCC-2-CRASHDUMP 2-Critical Fatal error calling crashdump error: [dec] [chars] A fatal condition has occurred causing IOS to crashdump. IOS will\n\ be restarted automatically. iosxe-chassismgr LOG_STD_ACTION CMANCC-3-MSGDISPATCH 3-Error Unable to dispatch received message from Chassis Manager An unexpected condition has occurred while IOS was trying to dispatch\n\ a message received from the Chassis Manager. iosxe-chassismgr "Verify that all local components are in the proper operational state.\n\ If any inconsistency is found it may be corrected by offlinine and\n\ restart of the effected component SPA Carrier Card" CMANCC-3-MSGDISPATCH 3-Error Unable to dispatch received message from Chassis Manager An unexpected condition has occurred while IOS was trying to dispatch\n\ a message received from the Chassis Manager. iosxe-chassismgr "Verify that all local components are in the proper operational state.\n\ If any inconsistency is found it may be corrected by offlinine and\n\ restart of the effected component SPA Carrier Card" CMANCC-3-MSGIPCERR 3-Error Unable to process received IPC messages from Chassis Manager\n\ error: [chars] An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Chassis Manager. iosxe-chassismgr LOG_STD_ACTION CMANCC-3-MSGIPCERR 3-Error Unable to process received IPC messages from Chassis Manager\n\ error: [chars] An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Chassis Manager. iosxe-chassismgr LOG_STD_ACTION CMANCC-3-UNEXPECTEDEVENT 3-Error UDI Auth Process received unknown event maj [hec] min [hec]. UDI auth process has registered to be notified when a process \n\ boolean change event occurs in the router. This message indicates \n\ that this process received an event it did not know how to handle. iosxe-chassismgr "Copy the error message exactly as it appears and report it\n\ to your technical support representative." CMANCC-3-UNEXPECTEDEVENT 3-Error UDI Auth Process received unknown event maj [hec] min [hec]. UDI auth process has registered to be notified when a process \n\ boolean change event occurs in the router. This message indicates \n\ that this process received an event it did not know how to handle. iosxe-chassismgr "Copy the error message exactly as it appears and report it\n\ to your technical support representative." CMANRP-2-CRASHDUMP 2-Critical Fatal error calling crashdump error: [dec] [chars] A fatal condition has occurred causing IOS to crashdump. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-CMREADFAIL 3-Error Read from cpld_ha fd [dec] failed errno [dec] event cnt [dec] Read from cpld_ha device returned 0 bytes. - LOG_STD_NO_ACTION CMANRP-3-CMSWVERINFO 3-Error Unable to process software version information using file [chars]. Reason: [chars]. Error: [dec] An unexpected condition has occurred while IOS was trying to process the software version information file. As a result version information may not be available to an SNMP Manager iosxe-chassismgr LOG_STD_NO_ACTION CMANRP-3-INVERR 3-Error Unable to process chassis inventory for file [chars] slot [dec] [chars] error [dec]. Some SPA's may not be fully configured An unexpected condition has occurred while IOS is trying to process the chassis inventory on startup. IOS can not determine the type and number of all Carrier Cards and SPA's present in the system. Some configuration relating to these SPA's may not be applied and leave the system in an inconsistent state. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-INVERRSPA 3-Error Unable to process chassis inventory for file [chars] SPA subslot [dec]/[dec] [chars] error [dec]. Some SPA's may not be fully configured An unexpected condition has occurred while IOS is trying to process the chassis inventory on startup. IOS can not determine the type and number of all Carrier Cards and SPA's present in the system. Some configuration relating to these SPA's may not be applied and leave the system in an inconsistent state. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message '[chars]' from Chassis Manager. LUID: [chars] An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages from Chassis Manager. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-MSGDISPATCHNULL 3-Error Received NULL TDL message from IOS An unexpected condition in which IOS has received a NULL TDL message from Chassis Manager. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-MSGIPCERR 3-Error Unable to process received IPC messages from Chassis Manager error: [chars] An unexpected condition has occurred while IOS is trying to process a received IPC message from Chassis Manager. iosxe-chassismgr LOG_STD_ACTION CMANRP-3-SMU_COMMITTED_FAILED 3-Error 'install commit' failed [dec] during reload. There are uncommitted SMU activity in the system reload will remove this SMU activity with user input install commit is tried but failed with the error code mentioned in message. iosxe-p-smu LOG_STD_NO_ACTION CMANRP-3-UDEVPERMS 3-Error An invalid permissions value [chars] was found in a udev file The udev files for a particular filesystem contain a description the file system. If the permissions attribute is not recognized then this file system may run with incorrect permissions. iosxe-chassismgr LOG_STD_NO_ACTION CMANRP-4-SMU_UNCOMMITTED 4-Warning There are uncommitted SMU abort reload and 'install commit' if required There are uncommitted SMU activity in the system reload will remove this SMU activity use 'install commit' to make it persistent. iosxe-p-smu LOG_STD_NO_ACTION CMANRP-6-CMHASTATUS 6-Information RP switchover [chars] RP switchover events received by chassis manager. - LOG_STD_NO_ACTION CMANRP-6-CMNOTSWITCH 6-Information RP is not doing switchover Read from cpld_ha device indicate no switchover event. - LOG_STD_NO_ACTION CMANRP-6-CMSTATUS 6-Information Chassis Manager Process is [chars] The current status of Chassis Manager Process. - LOG_STD_NO_ACTION CMANRP-6-CMSWREAD 6-Information RP switchover event triggered RP switchover event triggered by IOS fastpath. - LOG_STD_NO_ACTION CMANRP-6-SMU_COMMITTED 6-Information 'install commit' is success. There were uncommitted SMU activity in the system reload will remove this SMU activity with user input install commit is done. iosxe-p-smu LOG_STD_NO_ACTION CMCC-3-CFGCMDDROPPED 3-Error Config queue is full command was dropped slot [dec] Sending a config command was retried. The receiving queues were still full after retries therefore the command was dropped. cip "Issue thedebug channel events command and " "try each of the following tasks in sequence. If an action " "corrects the problem the remaining tasks do not need to be " "performed.\n" "Reissue the configuration command. " "Clear the interface using the clear interface " "command. " "Reload the microcode. " "Reload the router.\n" "If the error still occurs copy the error message exactly " "as it appears. Record the output from the following commands:\n" "show tech " "show log \n" "Provide this information to your technical support " "representative." CMCC-3-IPCBUFFAIL 3-Error Unable to obtain IPC resources The InterProcess Communication IPC service used by the TN3270 - "The CMCC will not load properly. Try the reload command again. If " "this message recurs call your technical support representative for " "assistance." CMCC-3-IPCDNSFAIL 3-Error DNS lookup failed - [chars] The InterProcess Communication IPC service used by the TN3270 - "Verify that the proper revisions of code are selected." CMCC-3-IPCINITFAIL 3-Error Unable to initialize IPC [chars] services The InterProcess Communication IPC service used by the TN3270 - "The CMCC will not load properly. The router must be reloaded to clear " "the problem." CMCC-3-IPCINVALID 3-Error Invalid IPC request [dec] received from [hec] The InterProcess Communication IPC service used by the TN3270 - "Verify that the proper revisions of code are selected." CMCC-3-RSETFAIL 3-Error Interface [chars]: Error %-04x [chars] An error occurred sending an interface enable or disable command. cip "The interface was reset by the software and the condition " "rectified. If that did not occur then issue the " "debug channel events command and " "try each of the following tasks in sequence. If an action " "corrects the problem the remaining tasks do not need to be " "performed.\n" "Clear the interface using the clear interface " "command. " "Reload the microcode. " "Reload the router.\n" "If the error still occurs copy the error message exactly " "as it appears. Record the output from the following commands:\n" "show tech " "show log \n" "Provide this information to your technical support " "representative." CMCC-3-UNKENCAP 3-Error Interface [chars]: unknown encapsulated msg[dec] len[dec] - - - CMCC-4-CFGFAIL 4-Warning Interface [chars]: configuration command [chars] [chars] failed An encapsulated control message had a size smaller than the minimum expected size. The message was dropped. cip LOG_STD_SH_TECH_ACTION CMCC-4-IPCDNSNOIPADDR 4-Warning DNS lookup failed - the DNS server has no entry for hostname [chars] The InterProcess Communication IPC service used by the TN3270 - "Verify that the DNS server entries are up to date." CMCC-5-IPCDNSQUERYTIMEDOUT 5-Notice DNS lookup failed - query to DNS server [chars] timed out The InterProcess Communication IPC service used by the TN3270 - "Check the status of the DNS server." CMCC-5-IPCDNSSERVERUNREACHABLE 5-Notice DNS lookup failed - DNS server [inet] is unreachable The InterProcess Communication IPC service used by the TN3270 - "Check for available routes to DNS servers." CMCC-6-ADAPTERCHNG 6-Information Interface [chars]: adapter type changed from [chars] to [chars] The channel-protocol configuration command sent after a reset failed to complete successfully. cip "The channel data transfer rate was reset to the default value. Reissue " "the configuration command." CMEXML-3-ABORTEXEC 3-Error \ CME XML Client Request Aborted request [chars]\n - - - CMEXML-3-ABORTEXEC 3-Error \ CME XML Client Request Aborted request [chars]\n - - - CMEXML-3-ERREXEC 3-Error \ CME XML Client Request Failed at [dec] request [chars]\n - - - CMEXML-3-ERREXEC 3-Error \ CME XML Client Request Failed at [dec] request [chars]\n - - - CMEXML-6-STARTEXEC 6-Information \ CME XML Client Request Start request [chars]\n - - - CMEXML-6-STARTEXEC 6-Information \ CME XML Client Request Start request [chars]\n - - - CMM-3-CONFIG_SIZE_EXCEED_LIMIT 3-Error Current config size is greater than supported size [dec]. Config CLI will not be synced to Centrally Managed Mobility Agents. The Maximum supported configuration size which can be synced has been reached hence no new configuration will be synced from Mobility Controller to Centrally Managed Mobility Agents. accsw-ease-of-use "Save the current configuration on the Mobility " "Controller so that the existing configuration can be synced to " "the Centrally Managed Mobility Agents." CMM-3-REGISTRY_ADD_ERR 3-Error Failure in adding to [chars] registry Could not add a function to the registry accsw-ease-of-use LOG_STD_NO_ACTION CMM-6-CENTRAL_MANAGMENT_DISABLED 6-Information This Mobility Agent is no more Centrally Managed. This Mobility Agent is no more Centrally Managed as the feature has either been disabled on the Controller or the Controller does not support this capability. Check the output of show wireless mobility summary on controller. accsw-ease-of-use "show wireless mobility " "summary" CMM-6-CONFIG_NOT_ALLOWED 6-Information Centrally Managed MA: \[chars]\ cannot be locally configured. This Mobility Agent is Centrally Managed hence this CLI is not allowed. Configuration needs to be done on the Mobility Controller. accsw-ease-of-use "show cmm config" CMM-6-CONFIG_SYNC_SAVE_MSG 6-Information Saving config rev#%llu received from Mobility Controller. On receiving config from Mobility Controller the config is automatically saved on the Mobility Agent accsw-ease-of-use - CMM-6-WIRELESS_MANAGEMENT_IP_CHANGED 6-Information The Mobility Controller wireless management interface IP Address has been modified. Please reload the Mobility Controller. The Mobility Controller wireless management interface IP Address has been modified. Please reload the Mobility Controller as this IP Address is used as the Domain ID for Central Management. accsw-ease-of-use LOG_STD_NO_ACTION CMP-4-MEM_CMPIP_ADDR_CONFLICT 4-Warning Conflict with CMP IP address [inet] Reissuing a new CMP IP address to member [dec] The cluster commander found a conflict with the assigned CMP IP address of the member. A new unique CMP IP address is assigned to the member. c2900-xl-cluster "This is a warning message only. The commander already assigned a new unique address to the member. Please clear any open TCP connections on the member using 'clear tcp' command." CMP-5-ADD 5-Notice The Device is added to the cluster Cluster Name: [chars] CMDR IP Address [inet] The device is added to the cluster c2900-xl-cluster LOG_STD_NO_ACTION CMP-5-MEMBER_CONFIG_UPDATE 5-Notice Received member configuration from member [dec] Received member configuration c2900-xl-cluster LOG_STD_NO_ACTION CMP-5-MGMT_VLAN_CHNG 5-Notice The management vlan has been changed to [dec] The management vlan has been changed c2900-xl-cluster LOG_STD_NO_ACTION CMP-5-NBR_UPD_SIZE_TOO_BIG 5-Notice Number of neighbors in neighbor update is [dec] maximum number of neighbors allowed in neighbor update is [dec] The number of cluster neighbors in the clustering neighbor update packet exceeds the number of neighbors supported by the clustering module design c2900-xl-cluster LOG_STD_NO_ACTION CMP-5-REMOVE 5-Notice The Device is removed from the cluster Cluster Name: [chars] The device is removed from the cluster c2900-xl-cluster LOG_STD_NO_ACTION CMTS_INFRA_LCHA-3-DMP_MCAST_STATUS_TBL_NULL 3-Error Error:mcast_flow_status_tbl is NULL! mcast_flow_status_tbl not initialized cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA_LCHA-3-SYNC_CONFIG_LIST_CREATION_FAILURE 3-Error DOCSIS SYNC configuration list creation failure current slot [dec] Failed to create the list of LCHA DOCSIS SYNC configuration cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA_LCHA-3-SYNC_CONFIG_LIST_INVALID 3-Error DOCSIS SYNC configuration list is invalid current slot [dec] virtual slot [dec] The list of LCHA DOCSIS SYNC configuration is invalid cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA_LCHA-4-RECONCIL_CM_CDM_MISMATCH 4-Warning LCHA CDMAN to LC CM Reconciliation: Mac: [enet] Reason: [chars] Mis-match between CDMAN and LC CM data cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA_LCHA-4-RECONCIL_DMP_MISMATCH 4-Warning LCHA CDMAN to LC DMP Reconciliation: HW-Flow: [dec] Reason: [chars] Mis-match between CDMAN and LC DMP data cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA_LCHA-4-RECONCIL_UMP_MISMATCH 4-Warning LCHA CDMAN to LC UMP Reconciliation: Service-Flow: [dec] Reason: [chars] Mis-match between CDMAN and LC UMP data cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-DBG_BG_INTF_PER_CTRL_EXCD 3-Error WB interface resource on [dec]/[dec]/[dec] Exhausted Unable to allocate additional WB Interface. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-FPM_ERR 3-Error [chars]: CM [enet] profile [dec] A service flow for the modem has been mapped to a profile that is not configured for the ofdm channel. cbr-cmts-infra "Remove or correct the ofdm-flow-to-profile " "configuration for the modem." CMTS_INFRA-3-NOENTROPY_PROC 3-Error Failed to create process to create entropy CLC doesn't receive HW entropy from RP for the last 10 minutes. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-NORAND64 3-Error Failed to read entropy from CPU Failure to retrieve entropy for random number generator. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-NORANDNIST 3-Error Failed to generate random number Failure to generate random number. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-NORES 3-Error [chars] [dec] [dec] An internal software error occurred. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-NORES_BG_EXCD 3-Error [chars] [dec] [dec] An internal software error occurred. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-NOTAMC 3-Error Failed to read entropy from ACT2 for [chars] err: 0x[hec] Failure to retrieve entropy for random number generator. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-PNM_INVALID_FREQ_SPAN_CFG 3-Error PNM: Capture tests cannot be started on port [dec]/[dec]/[dec] dev [dec] - Current capcfg freq: [dec]Hz span: [dec]Hz. For this user configured center freq [dec]Hz expected span value should not be more than [dec]Hz. PNM capture configuration has invalid values capture start rejected cbr-cmts-infra "Set the capture configuration center frequency " "and/or span to valid range as per suggested recommendations in msg to" " run captures." CMTS_INFRA-3-PNM_ZERO_FREQ_SPAN_CFG 3-Error PNM: Capture tests cannot be started on port [dec]/[dec]/[dec] dev [dec] - both capture config center frequency: [dec]Hz and span: [dec]Hz should be non zero or no meaningful data can be captured by CLC. PNM Capture center frequency and span cannot be zero to run captures cbr-cmts-infra "Set non zero valid values for capture configuration " "center frequency and span paramters to run captures." CMTS_INFRA-3-REALLOC_VALID_FLOW 3-Error Attempt to realloc valid flow: [dec] [enet] md[dec] sid[dec] sfid[dec] dsid[dec]. req: [enet] An internal software error occurred. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-3-RELOAD 3-Error Configuration changed for Gemini 1 ports on card in slot [dec]. Please reload the card for the changes to take effect and save the configuration. OFDMA channel bandwidth is too small to support the minimum number of mini-slots or no minislot to schedule IR/FR cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-5-DMP_INVAL_IDX 5-Notice Invalid Index: [dec] >= [dec] An internal software error occurred and an Invalid Index value was used. Such errors typically happen due to timing issues and can be ignored if only seen infrequently. Report the error to Tech Support if seen repeatedly. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_INFRA-6-CTRLR_CHAN_CONFIG_CONTINUOUS_CHANGE 6-Information [chars] channel [dec]/0/[dec]:[dec] configuration is being continuously changed or it's admin state is being continuously toggled causing the system to enter an indeterminate state recommend pacing controller/channel config changes. Controller/channel config is being continuously changed or it's admin state is being toggled this can put the system in an indeterminate state causing the modems to fall offline online or not come online. cbr-cmts-infra "Pace controller/channel configuration changes giving the system enough time to react to these events recommeded wait time is 30 seconds between config operations on controllers/channels use the recommendation to toggle channel admin state if modems don't come online or are partially online." CMTS_INFRA-6-CTRLR_PORT_ADMIN_STATE_LOCKED 6-Information User attempted to perform a no shut on Integrated-Cable [dec]/0/[dec] [dec] seconds after a shut event. This does not allow resources sufficient time to clean up. Calculated wait time was [dec] seconds between shut/no shut config operations on this controller. Controller is attempting to be no shut too soon after a shut event. This oepration was blocked to prevent resources from being reused before they have been cleaned up. cbr-cmts-infra - CMTS_INFRA-6-DELETE_HW_FLOW_MAC_MISMATCH 6-Information [chars] [dec] [enet]:[enet] An internal software error occurred. cbr-cmts-infra LOG_STD_SH_TECH_ACTION CMTS_LIC-1-BAD_LICENSE_STORAGE 1-Alert License Storage Error on Linecard [dec]/[dec] The Line card license storage status is BAD PLATFORM "Check the line card license details" " If the problem is not fixed by multiple reinstall attempts" " board RMA may be required" CMTS_LIC-3-APPLY_DS_FAILED 3-Error Applying downstream license failed Unable to apply the downstream license ubr10000 "Internal Error check license and report to TAC" CMTS_LIC-3-APPLY_US_FAILED 3-Error Applying upstream license failed Unable to apply the upstream license ubr10000 "Internal Error check license and report to TAC" CMTS_LIC-3-CSB_FAIL 3-Error [chars] failed for [chars] An attempt to parse a license related CLI failed PLATFORM "Check the linecard license details and call TAC" CMTS_LIC-3-INVALID_LIC_INFO 3-Error License Info Buffer is empty for [dec]/[dec] The license info buffer received/created from CLC is empty PLATFORM "Check the line card license details at CLC" CMTS_LIC-3-LCD_PROCESS_CREATE_FAIL 3-Error Could not create Update LCD process on Linecard [dec]/[dec] The Line card license LCD update process create failed ubr10000 LOG_STD_DDTS_TAC_DETAILS CMTS_LIC-3-LIC_LED_ERROR 3-Error Unable to set Downstream Density LED Unable to set Downstream Density LED PLATFORM "Try OIR the CLC and check the LED" CMTS_LIC-3-LIC_WDC_ALLOCATION_ERROR 3-Error Unable to allocate memory for WDC memory storage Unable to allocate memory for WDC memory PLATFORM "Try the command again at a later time" CMTS_LIC-3-LICENSE_ACTIVFAIL 3-Error Could not activate license module on Linecard [dec]/[dec] The Line card license module activation failed ubr10000 LOG_STD_DDTS_TAC_DETAILS CMTS_LIC-3-LICENSE_SEATNAME_ERROR 3-Error Unable to get slotid from [chars] Unable to get slotid PLATFORM "No action required" CMTS_LIC-3-NULL_HWIDB 3-Error Function [chars] invoked with hwidb NULL hwidb passed to function is NULL PLATFORM "Internal Error check license and report to TAC" CMTS_LIC-3-NULL_LICENSE_INFO 3-Error Line Card [dec]/[dec] license info is NULL! The Line card license info is NULL PLATFORM "Check the line card license details" CMTS_LIC-3-PROTECT_INVALID 3-Error Protect linecard [dec]/[dec] has lower license than the configured working Protect linecard has lower license than the working so HCCP configuration is now invalid for the protect linecard ubr10000 "Upgrade the license on the protect" CMTS_LIC-3-WORKING_INVALID 3-Error Working linecard [dec]/[dec] has higher license than the configured protect Working linecard has higher license than the protect so HCCP configuration is now invalid for the working linecard ubr10000 "Upgrade the license on the protect or downgrade" " the license on the working" CMTS_LIC-3-WORKING_PARTIAL 3-Error Working Linecard [dec]/[dec] License has been restricted. Please upgrade Protect Linecard License first and then reload working for complete fulfillment The working linecard license is now reduced because the working linecard license is higher than the protect linecard license ubr10000 "Please upgrade the license on the protect and then reload the working linecard" CMTS_LIC-4-LICENSE_PENDING 4-Warning License enforcement pending for Linecard [dec]/[dec] The linecard license enforcement will be delayed until the linecard transitions to active ubr10000 "No action required" CMTS_LIC-6-CHAN_NOSHUTFAIL 6-Information [chars] channel [dec] no shut is not allowed due to insufficient licenses Unable to no shut the channel due to insufficient licenses ubr10000 "Internal Error check number of licenses installed" CMTS_LIC-6-CHANNEL_NO_SHUTDOWN 6-Information [chars] channel [dec] has been restored to no shut Restored previously shutdown channels to no shut state ubr10000 "None" CMTS_LIC-6-CHANNEL_SHUTDOWN 6-Information [chars] channel [dec] has been shutdown due to insufficient licenses Unable to no shut the channel due to insufficient licenses ubr10000 "Internal Error check number of licenses installed" CMTS_LIC-6-LICENSE_ENFORCE 6-Information Linecard [dec]/[dec] set to mode [chars] License Information has been applied PLATFORM "No action required" CMTS_LIC-6-OUT_OF_RANGE 6-Information LC [dec]/[dec] [chars] is already [dec] License counters have reached boundary condition ubr10000 "Internal Error check license and report to TAC" CMTS-3-CABLE_IPC_SEND_FAILURE 3-Error cable nonblocked ipc send failed msg_type[[dec]] dst_slot[[dec]] Cable send nonblocked ipc failed cbr-application LOG_STD_NO_ACTION CMTS-3-DYN_SRV_IPC_SEND_FAILURE 3-Error [chars]_Tx: nonblocked send failed dst_slot [dec] Dynamic service failed to send nonblock IPC message cbr-application LOG_STD_NO_ACTION CMTS-3-INVALID_BW 3-Error Invalid bandwidth configuration: cir_pct [dec] cir_sum [dec] eir_sum [dec] Bandwidth configuration is invalid cmts LOG_STD_ACTION CMTS-3-LIST_CREATE 3-Error list create failed for list [chars] The Cisco CMTS router is unable to create list due to insufficient system memory cmts "Run the show memory command to verify available system memory. " "If memory is full contact your Cisco technical support " "representative and provide the representative with the " "gathered information" CMTS-3-LIST_CREATE 3-Error list create failed for list [chars] The Cisco CMTS router is unable to create list due to insufficient system memory cmts "Run the show memory command to verify available system memory. " "If memory is full contact your Cisco technical support " "representative and provide the representative with the " "gathered information" CMTS-3-LIST_ENQUEUE 3-Error list enqueue failed for list [chars] Unable to enqueue an entry to list cmts LOG_STD_ACTION CMTS-3-LIST_ENQUEUE 3-Error list enqueue failed for list [chars] Unable to enqueue an entry to list cmts LOG_STD_ACTION CMTS-3-LIST_INSERT 3-Error list insert failed for list [chars] The Cisco CMTS router is unable to insert an entry into list due to insufficient system memory or insert an exist entry cmts "Run the show memory command to verify available system memory. " "Then run the show logging command to view all system-logged " "messages. If memory is full contact your Cisco technical " "support representative and provide the representative with " "the gathered information" CMTS-3-LIST_INSERT 3-Error list insert failed for list [chars] The Cisco CMTS router is unable to insert an entry into list due to insufficient system memory or insert an exist entry cmts "Run the show memory command to verify available system memory. " "Then run the show logging command to view all system-logged " "messages. If memory is full contact your Cisco technical " "support representative and provide the representative with " "the gathered information" CMTS-3-MCAST_SES_MISMATCH 3-Error Session Request Response Mismatch for transaction ID [dec] session [chars][chars] CM [enet] Response from the LC does not match the session requested for. cmts LOG_STD_ACTION CMTS-3-MCAST_SES_MISMATCH 3-Error Session Request Response Mismatch for transaction ID [dec] session [chars][chars] CM [enet] Response from the LC does not match the session requested for. cmts LOG_STD_ACTION CMTS-3-PKTCBL_GATE_RECON_START 3-Error Pktcbl reconciliation [chars] in progress: Pktcbl Reconciliation started. packetcable LOG_STD_ACTION CMTS-4-CM_GET_RCC_FAILED_AFTER_LCHA 4-Warning failed to get rcc after LCSO Attempting to get rcc[[dec]] cm[[enet]] Find invalid rcc while cm recover cmts LOG_STD_ACTION CMTS-4-DELETE_BONDING_MISMATCH 4-Warning Error deleting upstream sid clusters CM[[enet]] docsis_prim_sid[[dec]] matches csc_sid[[dec]] The secondary sid should never match the primary. cmts LOG_STD_ACTION CMTS-4-DS_RESIL_FAILURE 4-Warning [chars]: [chars] failed DS Resiliency ipc message processing failure. cBR "." CMTS-4-ENQUEUE_SID_DUPLICATE 4-Warning Error enqueing sid element Attempting to enqueue sid[[dec]] onto sid_reuse_queue that already exists A duplicate sid should never exist in the free pool. cmts LOG_STD_ACTION CMTS-4-ENQUEUE_SID_INVALID 4-Warning Error enqueing sid element Attempting to enqueue invalid sid[[dec]] onto sid_reuse_queue An invalid sid cannot be added to the free pool. cmts LOG_STD_ACTION CMTS-4-PKTCBL_DB_ERROR 4-Warning Pktcbl failure op. [dec] type: [[dec]] gate id: [[dec]] sub_id: [[chars]] PacketCable database encounters an error Details embedded in message .. packetcable LOG_STD_NO_ACTION CMTS-4-PKTCBL_GATE_RECON_DONE 4-Warning Reconciliation [chars] for slot [dec] finished: Reconciliation completed print counters. packetcable LOG_STD_ACTION CMTS-4-PKTCBL_GATE_RECON_MISMATCHED 4-Warning Pktcbl reconciliation [chars] gate IE mismatched: Pktcbl reconciliation gate IE mismatched. packetcable LOG_STD_ACTION CMTS-4-PKTCBL_GATE_RECON_TIMEOUT 4-Warning Pktcbl reconciliation for slot [dec] timeout Usually the reconciliation will end after all gates' info being synced between SUP and LC. If we didn't get the end normally timer mechanism will take job and clean up left gates' info packetcable LOG_STD_ACTION CMTS-4-RECONCL_CM_FINISH_CLC 4-Warning Reconciliation [chars] for slot [dec] finished: Reconciliation finished print counters. cmts LOG_STD_ACTION CMTS-4-RECONCL_CM_FINISH_SUP 4-Warning Reconciliation [chars] for slot [dec] finished: Reconciliation finished print counters. cmts LOG_STD_ACTION CMTS-4-RECONCL_CM_MISMATCH 4-Warning Modem [enet] on Ca[dec]/0/[dec] mismatch during reconciliation delete reason: [chars] After the LC switchover modem info will be synced to SUP to compare if there is any info mismatcheg: modem state service flow info etc. the modem will be deleted fully. cmts LOG_STD_ACTION CMTS-4-RECONCL_CM_TIMEOUT 4-Warning Reconciliation for slot [dec] timeout Usually the reconciliation will end after all modem info being synced between SUP and LC. If we didn't get the end normally timer mechanism will take job and clean up left modem info cmts LOG_STD_ACTION CMTS-4-RECONCL_RESET_D31_CM_FINISH 4-Warning Reconciliation reset partial D31 CM for slot [dec] finished: D3.1 Online [dec] D3.1 DS partial [dec] D3.1 US partial [dec] D3.1 both partial [dec]. D3.0 DS partial [dec] D3.0 US partial [dec] D3.0 both partial [dec]. Reconciliation reset partial D31 CM finished print counters. cmts LOG_STD_ACTION CMTS-4-UPSTREAM_SID_MISMATCH 4-Warning Error populating upstream sid clusters CM[[enet]] docsis_prim_sid[[dec]] matches csc_sid[[dec]] The secondary sid should never match the primary. cmts LOG_STD_ACTION CMTS-6-PKTCBL_GATE_ERROR 6-Information Pktcbl failure op. [dec] type: [[dec]] gate id: [[dec]] sub_id: [[chars]] PacketCable encounters an error Details embedded in message .. packetcable LOG_STD_NO_ACTION CNS-3-CNS_DHCP_OP43_PROCESS_FAILED 3-Error PROCESSING FAILED The processing of CNS DHCP Option 43 message failed. - "Need to verify the CNS DHCP option 43 message is in correct format.\n\ If not correct it and send this message again." CNS-3-CNS_DHCP_OP43_PROCESS_FAILED 3-Error PROCESSING FAILED The processing of CNS DHCP Option 43 message failed. - "Need to verify the CNS DHCP option 43 message is in correct format.\n\ If not correct it and send this message again." CNS-3-FAULT 3-Error [chars] CNS subsystem has detected an internal exception condition cns-agents LOG_STD_ACTION CNS-3-FAULT 3-Error [chars] CNS subsystem has detected an internal exception condition cns-agents LOG_STD_ACTION CNS-3-MEMORY 3-Error [chars] CNS subsystem has experienced a problem gettting the required\n\ memory to complete this operation. cns_agents "Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required." CNS-3-MEMORY 3-Error [chars] CNS subsystem has experienced a problem gettting the required\n\ memory to complete this operation. cns_agents "Check system memory for other memory allocation errors and contact\n\ Technical support for problem resolution. In the absence of IOS errors\n\ upgrading the memory in the network device may be required." CNS-3-TRANSPORT 3-Error [chars] CNS subsystem has experienced a problem contacting an external\n\ application. cns_agents "See specific message text for an indication as to what the\n\ cause might be. Check the network configuration and cables to make\n\ sure the remote application is running and the address is accessible" CNS-3-TRANSPORT 3-Error [chars] CNS subsystem has experienced a problem contacting an external\n\ application. cns_agents "See specific message text for an indication as to what the\n\ cause might be. Check the network configuration and cables to make\n\ sure the remote application is running and the address is accessible" CNS-3-WARNING 3-Error [chars] CNS subsystem has experienced an unexpected condition executing\n\ a set of commands which did not cause a failure but suggests things\n\ did not go totally correctly cns_agents "Check the error log for additional information. This is an informational\n\ message and does not necessarily indicate an error did happen." CNS-3-WARNING 3-Error [chars] CNS subsystem has experienced an unexpected condition executing\n\ a set of commands which did not cause a failure but suggests things\n\ did not go totally correctly cns_agents "Check the error log for additional information. This is an informational\n\ message and does not necessarily indicate an error did happen." CNS-3-XML_SEMANTIC 3-Error [chars] CNS subsystem has experienced an error while processing the XML \n\ encapsulation of configuration command. cns_configagent "The externally supplied XML has errors in it and connot be processed.\n\ See specific message text for an indication as to what the\n\ cause might be. This will possible require the command to be\n\ checked and reissued from the server." CNS-3-XML_SEMANTIC 3-Error [chars] CNS subsystem has experienced an error while processing the XML \n\ encapsulation of configuration command. cns_configagent "The externally supplied XML has errors in it and connot be processed.\n\ See specific message text for an indication as to what the\n\ cause might be. This will possible require the command to be\n\ checked and reissued from the server." CNS-5-CNS_DHCP_OP43_PROCESS_DONE 5-Notice PROCESSING DONE The processing of CNS DHCP Option 43 message succeeded. - "None." CNS-5-CNS_DHCP_OP43_PROCESS_DONE 5-Notice PROCESSING DONE The processing of CNS DHCP Option 43 message succeeded. - "None." CNS-5-CONFIG_SUCCESS 5-Notice SUCCESSFUL_COMPLETION The configuration download has been applied successfully. - "None." CNS-5-CONFIG_SUCCESS 5-Notice SUCCESSFUL_COMPLETION The configuration download has been applied successfully. - "None." CNS-5-IOS_UP 5-Notice - - - - CNS-5-IOS_UP 5-Notice - - - - CNS-6-NO_EVENT_AGENT 6-Information CNS EVENT AGENT IS NOT CONFIGURED The cns event agent is not configured. The event that was to be sent to it will be dropped - "Configure the cns event agent." CNS-6-NO_EVENT_AGENT 6-Information CNS EVENT AGENT IS NOT CONFIGURED The cns event agent is not configured. The event that was to be sent to it will be dropped - "Configure the cns event agent." COBALT-3-COBERR 3-Error Cobalt [chars]. Cobalt generated an error. cr10k5 "Copy the error message exactly as it appears and report it to your " "technical support representative." COFF_INFRA-3-COFF_DECRYPT_RCY_PUNT 3-Error COFF attempted to punt pending decryption through RX-CR unsupported operation We tried to do a punt with a pending decryption scheduled cpp-ucode "File a bug with the COFF infra team" COFF_INFRA-3-COFF_MD_OOM 3-Error COFF attempted to allocate an MD object and failed MD pool ran dry and alloc failed cpp-ucode "Check 'sh plat hard qfp act da inf coff' CLI for MD mempool statistics" COFF_INFRA-3-COFF_SQNMGMT_OOM 3-Error COFF attempted to allocate an SQN Mgmt object and failed SQN Mgmt pool ran dry and alloc failed cpp-ucode "Check 'sh plat hard qfp act da inf coff' CLI for SQN Mgmt mempool statistics" COLLECTION-3-MODE_PRIORITY_MISMATCH 3-Error Attempted to start a walk with incompatible mode and priority mode [chars] priority [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-MODE_PRIORITY_MISMATCH 3-Error Attempted to start a walk with incompatible mode and priority mode [chars] priority [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-MODE_PROCESS_MISMATCH 3-Error Attempted to start a walk with incompatible mode and process mode [chars] process [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-MODE_PROCESS_MISMATCH 3-Error Attempted to start a walk with incompatible mode and process mode [chars] process [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-PROC_INIT 3-Error Initialization of process [chars] failed unable to [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-PROC_INIT 3-Error Initialization of process [chars] failed unable to [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-SUB_WALK 3-Error Subwalk mismatch walk %p priority [chars] mode [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTION-3-SUB_WALK 3-Error Subwalk mismatch walk %p priority [chars] mode [chars] COLLECTION_INTERNAL_ERROR COLLECTION_DDTS_COMPONENT LOG_STD_ACTION COLLECTOR-3-EXISTING_COLLECTOR 3-Error Collector [chars] already exists\n A collector already exists. Only one collector may be configured at a time. media-mon - collector "Modify the existing collector or remove it " "and create a new one with the desired name" COLLECTOR-3-EXISTING_COLLECTOR 3-Error Collector [chars] already exists\n A collector already exists. Only one collector may be configured at a time. media-mon - collector "Modify the existing collector or remove it " "and create a new one with the desired name" COLLECTOR-3-MODE_CHANGE_FAIL 3-Error The collector mode is invalid An error occurred when attempting change the collector mode. The mode has reverted to the previous value media-mon - collector LOG_STD_ACTION COLLECTOR-3-MODE_CHANGE_FAIL 3-Error The collector mode is invalid An error occurred when attempting change the collector mode. The mode has reverted to the previous value media-mon - collector LOG_STD_ACTION COLLECTOR-3-PORT_CHANGE_FAIL 3-Error Failed to set the collector port to [dec] An error occurred when attempting change the collector port. The port has reverted to the previous value media-mon - collector LOG_STD_ACTION COLLECTOR-3-PORT_CHANGE_FAIL 3-Error Failed to set the collector port to [dec] An error occurred when attempting change the collector port. The port has reverted to the previous value media-mon - collector LOG_STD_ACTION COLLECTOR-3-PROCESS_FAIL 3-Error Failed to start collector process An error occurred when attempting to start the collector media-mon - collector LOG_STD_ACTION COLLECTOR-3-PROCESS_FAIL 3-Error Failed to start collector process An error occurred when attempting to start the collector media-mon - collector LOG_STD_ACTION COLLECTOR-3-REMOVE_FAIL 3-Error The collector name is unrecognized The Collector name give does not match the collector configured media-mon - collector LOG_STD_ACTION COLLECTOR-3-REMOVE_FAIL 3-Error The collector name is unrecognized The Collector name give does not match the collector configured media-mon - collector LOG_STD_ACTION COLLECTOR-3-RESETMODE 3-Error Failed to reset csb vars Reset of the csb vars failed due to lack of memory media-mon - collector LOG_STD_ACTION COLLECTOR-3-RESETMODE 3-Error Failed to reset csb vars Reset of the csb vars failed due to lack of memory media-mon - collector LOG_STD_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error ERRMSG_FLAG_TRACEBACK - - - COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS_LSPV Service nabled SRVNAME_MPLS_OAM SYSLOGDOC_NO_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS_LSPV Service Disabled SRVNAME_MPLS_OAM SYSLOGDOC_NO_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS OAM Daemon Initialization failed. [chars] explains the reason for the failure. SYSLOGDOC_NO_DDTS SYSLOGDOC_NO_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error - - - - COMM_UNKNOWN_RC-3-LSPV 3-Error ERRMSG_FLAG_TRACEBACK - - - COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS_LSPV Service nabled SRVNAME_MPLS_OAM SYSLOGDOC_NO_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS_LSPV Service Disabled SRVNAME_MPLS_OAM SYSLOGDOC_NO_ACTION COMM_UNKNOWN_RC-3-LSPV 3-Error - MPLS OAM Daemon Initialization failed. [chars] explains the reason for the failure. SYSLOGDOC_NO_DDTS SYSLOGDOC_NO_ACTION COMMON_FIB-2-FIBTABLEILLEGAL 2-Critical Attempt to used uninitialized CEF data structure. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-FIBTABLEILLEGAL 2-Critical Attempt to used uninitialized CEF data structure. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-HW_IF_INDEX_ILLEGAL 2-Critical Attempt to create CEF interface for [chars] with illegal index: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-HW_IF_INDEX_ILLEGAL 2-Critical Attempt to create CEF interface for [chars] with illegal index: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-IF_NUMBER_ILLEGAL 2-Critical Attempt to create CEF interface for [chars] with illegal if_number: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-IF_NUMBER_ILLEGAL 2-Critical Attempt to create CEF interface for [chars] with illegal if_number: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-IFINDEXBOUNDS 2-Critical Attempt to use out of bounds interface index: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-2-IFINDEXBOUNDS 2-Critical Attempt to use out of bounds interface index: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ACL_PBR_NAMETOOLONG 3-Error IPV6_SWSB_CTRL name length error [chars] acl_in [dec] [dec] IPv6 in/out ACL and IPv6 PBR name lengths for/from an IPC XDR message are invalid. The names will not be used so as to prevent any buffer overrun errors. There is a possibility that either the XDR message or an internal IPv6 FIB structure is corrupted IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ACL_PBR_NAMETOOLONG 3-Error IPV6_SWSB_CTRL name length error [chars] acl_in [dec] [dec] IPv6 in/out ACL and IPv6 PBR name lengths for/from an IPC XDR message are invalid. The names will not be used so as to prevent any buffer overrun errors. There is a possibility that either the XDR message or an internal IPv6 FIB structure is corrupted IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ASSERT 3-Error Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ASSERT 3-Error Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ASSERT_RL 3-Error Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars]. - - - COMMON_FIB-3-ASSERT_RL 3-Error Assertion '[chars]' failed in [chars] CEF [0x%08x]: [chars] [chars][chars]. - - - COMMON_FIB-3-BFD 3-Error [chars][chars][chars][chars][chars][chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BFD 3-Error [chars][chars][chars][chars][chars][chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BFD_SESS 3-Error [chars]:[chars] failed to [chars] BFD session error [[chars]] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BFD_SESS 3-Error [chars]:[chars] failed to [chars] BFD session error [[chars]] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BINDINGLABEL 3-Error Binding label [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BINDINGLABEL 3-Error Binding label [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-BROKER_ENCODE 3-Error [chars] broker failed to encode msg type [dec] for slots [chars] - - - COMMON_FIB-3-BROKER_ENCODE 3-Error [chars] broker failed to encode msg type [dec] for slots [chars] - - - COMMON_FIB-3-CHAIN_BAD_MAGIC 3-Error Bad magic for element %p 0x%08x != 0x%08x - - - COMMON_FIB-3-CHAIN_BAD_MAGIC 3-Error Bad magic for element %p 0x%08x != 0x%08x - - - COMMON_FIB-3-DEPENDENCY_CHAIN 3-Error Missing handler for type [dec] dependency COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DEPENDENCY_CHAIN 3-Error Missing handler for type [dec] dependency COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DEPENDENCY_WALK 3-Error Walk specification %p missing handler for type [dec] dependency COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DEPENDENCY_WALK 3-Error Walk specification %p missing handler for type [dec] dependency COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_ACTIVE_COLLECTION 3-Error dqueue has an active collection just prior to destruction COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_ACTIVE_COLLECTION 3-Error dqueue has an active collection just prior to destruction COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_ELEM 3-Error Unexpected element type [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_ELEM 3-Error Unexpected element type [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_NEXT 3-Error elem %p type 0x[hec] elem->next %p elem->next_type 0x[hec] elem->next->prev %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_NEXT 3-Error elem %p type 0x[hec] elem->next %p elem->next_type 0x[hec] elem->next->prev %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_PREV 3-Error elem %p type 0x[hec] elem->prev %p elem->prev_type 0x[hec] elem->prev->next %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_BAD_PREV 3-Error elem %p type 0x[hec] elem->prev %p elem->prev_type 0x[hec] elem->prev->next %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_NON_EMPTY 3-Error dqueue is not empty just prior to destruction COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-DQUEUE_NON_EMPTY 3-Error dqueue is not empty just prior to destruction COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-EPOCH 3-Error Failed to start [chars] of [chars]entries in table [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-EPOCH 3-Error Failed to start [chars] of [chars]entries in table [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_ADJ_LINKTYPE 3-Error OCE chain for [chars] terminates with [chars] linktype is [chars] not [chars] An OCE chain for a FIB entry terminates with a linktype other than what was expected. This will cause encapsulation problems in the dataplane. COMMON_FIB_DDTS_COMPONENT "Get the full show ip[v6] cef internal" " output of the affected FIB entry and determine" " if anything looks wrong. For instance is a label" " or a midchain adjacency missing?" COMMON_FIB-3-FIB_ADJ_LINKTYPE 3-Error OCE chain for [chars] terminates with [chars] linktype is [chars] not [chars] An OCE chain for a FIB entry terminates with a linktype other than what was expected. This will cause encapsulation problems in the dataplane. COMMON_FIB_DDTS_COMPONENT "Get the full show ip[v6] cef internal" " output of the affected FIB entry and determine" " if anything looks wrong. For instance is a label" " or a midchain adjacency missing?" COMMON_FIB-3-FIB_ATTACHED_EXPORT 3-Error Attached export tracking error: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_ATTACHED_EXPORT 3-Error Attached export tracking error: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE 3-Error [chars] for [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE 3-Error [chars] for [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE_IPL_SB 3-Error [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE_IPL_SB 3-Error [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE_NULL_FIBIDB 3-Error [chars] NULL fibidb in broadcast sb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_FIB_SOURCE_NULL_FIBIDB 3-Error [chars] NULL fibidb in broadcast sb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_GSB 3-Error Generic subblock error: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_GSB 3-Error Generic subblock error: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_GSB2 3-Error Generic subblock error: [chars][chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_GSB2 3-Error Generic subblock error: [chars][chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_MAP 3-Error [chars] map [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_MAP 3-Error [chars] map [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_MAP_NO_USEABLE_CHOICES 3-Error No useable choices %04x bucket count [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_MAP_NO_USEABLE_CHOICES 3-Error No useable choices %04x bucket count [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_USAGE 3-Error Unhandled usage flag 0x[hec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_LOADBALANCE_USAGE 3-Error Unhandled usage flag 0x[hec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_MPLS_EXT_FIND_OCE 3-Error Unable to find MPLS oce for [chars] IP oce COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_MPLS_EXT_FIND_OCE 3-Error Unable to find MPLS oce for [chars] IP oce COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_NON_IP_ENTRY_INCR 3-Error [chars] non-ip entry 0x%08x path list [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_NON_IP_ENTRY_INCR 3-Error [chars] non-ip entry 0x%08x path list [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_OCC_DEP_DUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_OCC_DEP_DUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_PATH_LIST_DB 3-Error [chars] path list [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_PATH_LIST_DB 3-Error [chars] path list [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_XDR_BUF_OVERFLOW 3-Error FIB XDR buffer overflow while encoding [chars] [[chars]] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIB_XDR_BUF_OVERFLOW 3-Error FIB XDR buffer overflow while encoding [chars] [[chars]] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBCOVEREDDEPDUMP 3-Error [chars] [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBCOVEREDDEPDUMP 3-Error [chars] [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBHWIDB_NONAME 3-Error Missing name for fibhwidb ifindex [dec] - - - COMMON_FIB-3-FIBHWIDB_NONAME 3-Error Missing name for fibhwidb ifindex [dec] - - - COMMON_FIB-3-FIBHWIDBINCONS 3-Error An internal software error occurred. [chars] linked to wrong hwidb [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBHWIDBINCONS 3-Error An internal software error occurred. [chars] linked to wrong hwidb [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_INTERNAL 3-Error fibidb [chars] if_nb [dec] could not be [chars] db COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_INTERNAL 3-Error fibidb [chars] if_nb [dec] could not be [chars] db COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_MEM 3-Error [chars] chunk pool could not be [chars]. Possible memory leak. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_MEM 3-Error [chars] chunk pool could not be [chars]. Possible memory leak. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_NULL_FIBIDB 3-Error API called with NULL fibidb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDB_DB_NULL_FIBIDB 3-Error API called with NULL fibidb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBEARLYCALL 3-Error Attempt to update fibidb prior to completion of idb initialization. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBEARLYCALL 3-Error Attempt to update fibidb prior to completion of idb initialization. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBINCONS1 3-Error An internal software error occurred. [chars] should be first fibidb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBINCONS1 3-Error An internal software error occurred. [chars] should be first fibidb COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBINCONS2 3-Error An internal software error occurred. [chars] linked to wrong idb [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBINCONS2 3-Error An internal software error occurred. [chars] linked to wrong idb [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBNONBASETABLE 3-Error interface [chars] being set with non-base table: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBIDBNONBASETABLE 3-Error interface [chars] being set with non-base table: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- FIBINVPEXTLEN 3-Error [chars] ext attempt to decode beyond XDR buffer cp_cur 0x[hec] cp_end 0x[hec] num_ext [dec] curr_ext_idx [dec] The path extension decode logic is trying to access memory beyond XDR buffer which can lead to memory corruption. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- FIBINVPEXTLEN 3-Error [chars] ext attempt to decode beyond XDR buffer cp_cur 0x[hec] cp_end 0x[hec] num_ext [dec] curr_ext_idx [dec] The path extension decode logic is trying to access memory beyond XDR buffer which can lead to memory corruption. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBLBCLPSECHAINDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBLBCLPSECHAINDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBPLDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBPLDEPDUMP 3-Error [chars] COMMON_FIB_INTERNAL_ERROR OCE_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBSUBTREECONTEXT 3-Error Subtree context unexpected error: app [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBSUBTREECONTEXT 3-Error Subtree context unexpected error: app [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTABLE 3-Error Error for table [dec]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTABLE 3-Error Error for table [dec]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTOPO 3-Error Error for topology [dec]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTOPO 3-Error Error for topology [dec]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTOPOSTAT 3-Error Error pulling topology stats [chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBTOPOSTAT 3-Error Error pulling topology stats [chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBXDRCLIENT 3-Error FIB XDR Client error detected invalid wkid: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBXDRCLIENT 3-Error FIB XDR Client error detected invalid wkid: [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBXDRINV 3-Error Invalid XDR format. [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBXDRINV 3-Error Invalid XDR format. [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-FIBXDRLEN 3-Error Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec] - - - COMMON_FIB-3-FIBXDRLEN 3-Error Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec] - - - COMMON_FIB-3-HW_API 3-Error HW API failure for [chars] CEF [0x%08x]: [chars] [chars][chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-HW_API 3-Error HW API failure for [chars] CEF [0x%08x]: [chars] [chars][chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ILIST_OP 3-Error Manipulating interest list - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ILIST_OP 3-Error Manipulating interest list - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-ILLEGAL_MSG_TYPE 3-Error Cannot find ISSU message type for FIB [chars] [dec] [chars]SB [chars] msg - - - COMMON_FIB-3-ILLEGAL_MSG_TYPE 3-Error Cannot find ISSU message type for FIB [chars] [dec] [chars]SB [chars] msg - - - COMMON_FIB-3-ILLEGAL_TABLEID 3-Error Attempt to create [chars] table with illegal tableid [dec] [chars]:[chars] - - - COMMON_FIB-3-ILLEGAL_TABLEID 3-Error Attempt to create [chars] table with illegal tableid [dec] [chars]:[chars] - - - COMMON_FIB-3- ILLEGALARGS 3-Error Illegal arguments - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- ILLEGALARGS 3-Error Illegal arguments - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-INVALID_ADDR_TYPE 3-Error Invalid address type [dec][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-INVALID_ADDR_TYPE 3-Error Invalid address type [dec][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-INVALID_AF 3-Error Invalid address family [dec][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-INVALID_AF 3-Error Invalid address family [dec][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-IPMFI_TIMING_PRESENT 3-Error IPMFI Timing Tool present in image - performance will be degraded COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-IPMFI_TIMING_PRESENT 3-Error IPMFI Timing Tool present in image - performance will be degraded COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- ISSU_ENUM_ERROR 3-Error Enum for [chars] is not ISSU-compliant: [chars] The given enumeration is not ISSU-compliant for the reason given. Unpredictable behaviour will result when interoperating with different IOS versions. COMMON_FIB_DDTS_COMPONENT "This requires a code fix before the image can be shipped or ISSU will be " "broken." COMMON_FIB-3- ISSU_ENUM_ERROR 3-Error Enum for [chars] is not ISSU-compliant: [chars] The given enumeration is not ISSU-compliant for the reason given. Unpredictable behaviour will result when interoperating with different IOS versions. COMMON_FIB_DDTS_COMPONENT "This requires a code fix before the image can be shipped or ISSU will be " "broken." COMMON_FIB-3-ISSU_REG 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] ISSU negotiation failed for this XDR client. COMMON_FIB_DDTS_COMPONENT "This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it." COMMON_FIB-3-ISSU_REG 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] ISSU negotiation failed for this XDR client. COMMON_FIB_DDTS_COMPONENT "This error indicates a coding problem. It is an error that will occur" "every time this image is run and requires a code change to fix it." COMMON_FIB-3-LOADBALANCE_LOOP 3-Error Detected loop while installing OCE: [chars] %p to loadinfo: [chars] %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-LOADBALANCE_LOOP 3-Error Detected loop while installing OCE: [chars] %p to loadinfo: [chars] %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-MSGISSUAWARE 3-Error Message [chars] [dec] is ISSU aware so cannot use old FIB API. ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-MSGISSUAWARE 3-Error Message [chars] [dec] is ISSU aware so cannot use old FIB API. ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NAMETOOLONG 3-Error FIB[chars]IDB name [chars] error lengths [dec] [dec] short [dec] [dec] - - - COMMON_FIB-3-NAMETOOLONG 3-Error FIB[chars]IDB name [chars] error lengths [dec] [dec] short [dec] [dec] - - - COMMON_FIB-3-NO_TABLE_NAME 3-Error Attempt to clear the name of [chars] table with tableid [dec] previous name [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NO_TABLE_NAME 3-Error Attempt to clear the name of [chars] table with tableid [dec] previous name [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NO_VALID_PATHS 3-Error No valid paths for prefix [chars] in vrf [chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NO_VALID_PATHS 3-Error No valid paths for prefix [chars] in vrf [chars]. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOBROKER 3-Error [chars] distribution broker not found - distributing [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOBROKER 3-Error [chars] distribution broker not found - distributing [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOHWSBDECODE 3-Error No [chars] subblock control decode function for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOHWSBDECODE 3-Error No [chars] subblock control decode function for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOLABELNOLABEL 3-Error Unexpected disposition information for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOLABELNOLABEL 3-Error Unexpected disposition information for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- NOMEM 3-Error Memory allocation failure for [chars] in [chars] CEF [0x%08x] [chars][chars]. - - - COMMON_FIB-3- NOMEM 3-Error Memory allocation failure for [chars] in [chars] CEF [0x%08x] [chars][chars]. - - - COMMON_FIB-3-NOPATHFIBIDB 3-Error No fibidb for [chars] ignoring path during path no [dec] update for [chars] - - - COMMON_FIB-3-NOPATHFIBIDB 3-Error No fibidb for [chars] ignoring path during path no [dec] update for [chars] - - - COMMON_FIB-3-NOSUCHCAPTURE 3-Error Error finding capture point. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOSUCHCAPTURE 3-Error Error finding capture point. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOSWSBDECODE 3-Error No [chars] subblock control decode function for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-NOSWSBDECODE 3-Error No [chars] subblock control decode function for [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- PATH_EXT_DUPLICATE 3-Error Detected identical [chars] path extension [chars] ext %p - replacing. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- PATH_EXT_DUPLICATE 3-Error Detected identical [chars] path extension [chars] ext %p - replacing. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-PATH_EXT_ENCODE 3-Error Failed to encode [chars] path extension [chars] One or more path extensions could not be encoded for distribution and will not be sent. This indicates an internal code error and may impact CEF operation for prefixes using the affected path extensions. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-PATH_EXT_ENCODE 3-Error Failed to encode [chars] path extension [chars] One or more path extensions could not be encoded for distribution and will not be sent. This indicates an internal code error and may impact CEF operation for prefixes using the affected path extensions. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-PATH_EXT_ISSU_SR_LDP 3-Error Dowgrading to a version that doesn't support Segment Routing and LDP on the same path labels [[dec]|[dec]]. This indicates there's an issue in ISSU transformation when downgrading to a lower version. Configuration changes might be required to avoid this issue. See recommended action. COMMON_FIB_DDTS_COMPONENT "Find out the prefix which is using the two outgoing " "labels as shown in the message with 'show mpls forwarding-table'. Check " "IGP configuration and disable either LDP or SR on that prefix." COMMON_FIB-3-PATH_EXT_ISSU_SR_LDP 3-Error Dowgrading to a version that doesn't support Segment Routing and LDP on the same path labels [[dec]|[dec]]. This indicates there's an issue in ISSU transformation when downgrading to a lower version. Configuration changes might be required to avoid this issue. See recommended action. COMMON_FIB_DDTS_COMPONENT "Find out the prefix which is using the two outgoing " "labels as shown in the message with 'show mpls forwarding-table'. Check " "IGP configuration and disable either LDP or SR on that prefix." COMMON_FIB-3- PATH_EXT_PLIST_CHG_DUP_SHORT 3-Error Detected identical short path extension following path list change idx [dec] type [dec] [[chars] --> [chars]] conv [dec] renum [dec] total short [dec] ext list %p. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3- PATH_EXT_PLIST_CHG_DUP_SHORT 3-Error Detected identical short path extension following path list change idx [dec] type [dec] [[chars] --> [chars]] conv [dec] renum [dec] total short [dec] ext list %p. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-PATH_INVALID_REPAIR 3-Error Primary or repair paths configured by RIB are of invalid type: primary: [chars] repair: [chars] Either the primary path or the repair path is not of the correct type i.e. an attached nexthop that provides both interface and nexthop COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-PATH_INVALID_REPAIR 3-Error Primary or repair paths configured by RIB are of invalid type: primary: [chars] repair: [chars] Either the primary path or the repair path is not of the correct type i.e. an attached nexthop that provides both interface and nexthop COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-SBNOTISSUAWARE 3-Error Subblock [chars] is not ISSU aware and should be! ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-SBNOTISSUAWARE 3-Error Subblock [chars] is not ISSU aware and should be! ALL FIB subblocks must be ISSU aware. The subblock code must be rewritten for ISSU. Otherwise this may lead to unpredictable behaviour when running in SSO mode with two different versions of IOS. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-SBWITHOUTISSUSUPPORT 3-Error [chars] [chars] subblock doesn't support ISSU and can't be used. The given SW subblock doesn't support ISSU so may not be processed correctly on the LC. It has not been registered by the CEF component. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-SBWITHOUTISSUSUPPORT 3-Error [chars] [chars] subblock doesn't support ISSU and can't be used. The given SW subblock doesn't support ISSU so may not be processed correctly on the LC. It has not been registered by the CEF component. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-TABLE 3-Error [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-TABLE 3-Error [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-TABLE_CONCURRENT_UPDATE 3-Error [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-TABLE_CONCURRENT_UPDATE 3-Error [chars]: [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-UNHANDLED_UNITS 3-Error No handler for units [chars] - from slot [chars] - - - COMMON_FIB-3-UNHANDLED_UNITS 3-Error No handler for units [chars] - from slot [chars] - - - COMMON_FIB-3-VRFID_INVALID 3-Error Error invalid vrfid [chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-VRFID_INVALID 3-Error Error invalid vrfid [chars][chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-VRFMGR_INVALID 3-Error Error invalid [chars] [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-3-VRFMGR_INVALID 3-Error Error invalid [chars] [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-AUTOREPAIR 4-Warning CEF [chars] database auto-repair executed The CEF consistency checkers have detected an inconsistent prefix in one of the CEF forwarding databases. The auto-repair function has been executed to repair the problem. Details of the prefix can be found using the 'show cef table consistency' command. COMMON_FIB_DDTS_COMPONENT "Copy the message exactly as it appears together with the output of " "the 'show cef table consistency' command and report it to your " "technical support representative" COMMON_FIB-4-AUTOREPAIR 4-Warning CEF [chars] database auto-repair executed The CEF consistency checkers have detected an inconsistent prefix in one of the CEF forwarding databases. The auto-repair function has been executed to repair the problem. Details of the prefix can be found using the 'show cef table consistency' command. COMMON_FIB_DDTS_COMPONENT "Copy the message exactly as it appears together with the output of " "the 'show cef table consistency' command and report it to your " "technical support representative" COMMON_FIB-4-BADXDRHWSBDECODE 4-Warning HW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec] - - - COMMON_FIB-4-BADXDRHWSBDECODE 4-Warning HW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec] - - - COMMON_FIB-4-BADXDRSWSBDECODE 4-Warning SW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec] - - - COMMON_FIB-4-BADXDRSWSBDECODE 4-Warning SW subblock decode [chars] / [dec] - wrong length read expected [dec] decoded [dec] - - - COMMON_FIB-4-BROKERINVMSG 4-Warning Invalid message: [chars] type [chars] len [dec] An invalid message has been received by this broker. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-BROKERINVMSG 4-Warning Invalid message: [chars] type [chars] len [dec] An invalid message has been received by this broker. COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_INSERT_INCONS1 4-Warning Attempting to insert %p after %p but it is still pointed at by %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_INSERT_INCONS1 4-Warning Attempting to insert %p after %p but it is still pointed at by %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_INSERT_INCONS2 4-Warning Attempting to insert %p after %p but it has prev set to %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_INSERT_INCONS2 4-Warning Attempting to insert %p after %p but it has prev set to %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_REMOVE_INCONS1 4-Warning Attempting to remove %p but prev %p points at %p instead COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_REMOVE_INCONS1 4-Warning Attempting to remove %p but prev %p points at %p instead COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_REMOVE_INCONS2 4-Warning Attempting to remove %p but it has no prev next is %p - - - COMMON_FIB-4-CHAIN_REMOVE_INCONS2 4-Warning Attempting to remove %p but it has no prev next is %p - - - COMMON_FIB-4-CHAIN_REMOVE_INCONS3 4-Warning Attempting to remove %p with next %p thinks its prev is %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-CHAIN_REMOVE_INCONS3 4-Warning Attempting to remove %p with next %p thinks its prev is %p COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-DISABLING 4-Warning [chars] CEF is being disabled due to a fatal error. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-DISABLING 4-Warning [chars] CEF is being disabled due to a fatal error. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIB_OCC_SB_REMOVE_FAIL 4-Warning Attempted to remove subblock of type '[chars]' [dec] for [chars] failed - - - COMMON_FIB-4-FIB_OCC_SB_REMOVE_FAIL 4-Warning Attempted to remove subblock of type '[chars]' [dec] for [chars] failed - - - COMMON_FIB-4-FIB_SB_ADD_FAIL 4-Warning Attempted add of subblock of type '[chars]' [dec] for [chars] failed[chars] - - - COMMON_FIB-4-FIB_SB_ADD_FAIL 4-Warning Attempted add of subblock of type '[chars]' [dec] for [chars] failed[chars] - - - COMMON_FIB-4-FIBHWIDB 4-Warning No fibhwidb for [chars] found during [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBHWIDB 4-Warning No fibhwidb for [chars] found during [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBHWIDBMISMATCH 4-Warning Mis-match between hwidb [chars] ifindex [dec] and fibhwidb [chars] ifindex [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBHWIDBMISMATCH 4-Warning Mis-match between hwidb [chars] ifindex [dec] and fibhwidb [chars] ifindex [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBIDB 4-Warning No fibidb found for [chars] during [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBIDB 4-Warning No fibidb found for [chars] during [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBIDBMISMATCH 4-Warning Mis-match between idb [chars] if_number [dec] and fibidb [chars] if_number [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBIDBMISMATCH 4-Warning Mis-match between idb [chars] if_number [dec] and fibidb [chars] if_number [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBMISSINGHWIDB 4-Warning No fibhwidb while initializing fibidb for [chars] if_number [dec] - - - COMMON_FIB-4-FIBMISSINGHWIDB 4-Warning No fibhwidb while initializing fibidb for [chars] if_number [dec] - - - COMMON_FIB-4-FIBMSG 4-Warning Invalid message received. Type [chars] event/sub-type [dec] length [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBMSG 4-Warning Invalid message received. Type [chars] event/sub-type [dec] length [dec] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-FIBNULLHWIDB 4-Warning Missing hwidb for fibhwidb [chars] ifindex [dec] - - - COMMON_FIB-4-FIBNULLHWIDB 4-Warning Missing hwidb for fibhwidb [chars] ifindex [dec] - - - COMMON_FIB-4-FIBNULLIDB 4-Warning Missing idb for fibidb [chars] if_number [dec]. - - - COMMON_FIB-4-FIBNULLIDB 4-Warning Missing idb for fibidb [chars] if_number [dec]. - - - COMMON_FIB-4-FIBXDR_REGISTRATION 4-Warning Unable to register XDR client [chars]. - - - COMMON_FIB-4-FIBXDR_REGISTRATION 4-Warning Unable to register XDR client [chars]. - - - COMMON_FIB-4-HWPREFIXINCONST1 4-Warning Hardware on RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP FIB [[chars]] A passive consistency checker discovered a prefix in the RP FIB table which is not present in the hardware forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST1 4-Warning Hardware on RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP FIB [[chars]] A passive consistency checker discovered a prefix in the RP FIB table which is not present in the hardware forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST2 4-Warning Hardware in slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC FIB [[chars]] A passive consistency checker discovered a prefix in the LC FIB table which is not present in the hardware forwarding table on this linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST2 4-Warning Hardware in slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC FIB [[chars]] A passive consistency checker discovered a prefix in the LC FIB table which is not present in the hardware forwarding table on this linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST3 4-Warning RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP hardware [[chars]] A passive consistency checker discovered a prefix in the hardware table which is not present in the FIB forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST3 4-Warning RP missing prefix for [chars]/[dec] in FIB table [chars] present in RP hardware [[chars]] A passive consistency checker discovered a prefix in the hardware table which is not present in the FIB forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST4 4-Warning Slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC hardware [[chars]] A passive consistency checker discovered a prefix in the LC hardware table which is not present in the FIB forwarding table on this linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-HWPREFIXINCONST4 4-Warning Slot [chars] missing prefix for [chars]/[dec] in FIB table [chars] present in LC hardware [[chars]] A passive consistency checker discovered a prefix in the LC hardware table which is not present in the FIB forwarding table on this linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-ISSUBUFFERTOOSHORTMSG 4-Warning Message [chars] for slots [chars] is too large [dec] bytes max [dec] - - - COMMON_FIB-4-ISSUBUFFERTOOSHORTMSG 4-Warning Message [chars] for slots [chars] is too large [dec] bytes max [dec] - - - COMMON_FIB-4-ISSUENCODEWRONGLEN 4-Warning Message [chars] for slots [chars] is wrong length [dec] should be [dec] - - - COMMON_FIB-4-ISSUENCODEWRONGLEN 4-Warning Message [chars] for slots [chars] is wrong length [dec] should be [dec] - - - COMMON_FIB-4-LCPREFIXINCONST1 4-Warning Slot [chars] missing prefix entry for [chars] in FIB table [chars] when looking up [chars] [[chars]] A packet arrived on the linecard but the lookup of the destination IP address failed to find this prefix in the forwarding table. However the prefix is present on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes." COMMON_FIB-4-LCPREFIXINCONST1 4-Warning Slot [chars] missing prefix entry for [chars] in FIB table [chars] when looking up [chars] [[chars]] A packet arrived on the linecard but the lookup of the destination IP address failed to find this prefix in the forwarding table. However the prefix is present on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes." COMMON_FIB-4-LCPREFIXINCONST2 4-Warning Slot [chars] prefix entry for [chars]/[dec] in FIB table [chars] [[chars]] reason: [chars] A passive consistency checker discovered a prefix that is present on the RP but is inconsistent in the forwarding table of the linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes." COMMON_FIB-4-LCPREFIXINCONST2 4-Warning Slot [chars] prefix entry for [chars]/[dec] in FIB table [chars] [[chars]] reason: [chars] A passive consistency checker discovered a prefix that is present on the RP but is inconsistent in the forwarding table of the linecard. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the CEF prefix on the " "RP and linecard. If necessary a clear cef linecard " "will download a new CEF table to the linecard. You can also " "try a clear adjacency command to reload host prefixes." COMMON_FIB-4- MAX_PATHS_EXCEEDED 4-Warning Prefix [chars] in vrf [chars] has paths in excess of the maximum. Some may be dropped. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4- MAX_PATHS_EXCEEDED 4-Warning Prefix [chars] in vrf [chars] has paths in excess of the maximum. Some may be dropped. COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-RPPREFIXINCONST1 4-Warning RP prefix for [chars]/[dec] in FIB table [chars] inconsistent on slot [chars] - [chars] [[chars]] - - - COMMON_FIB-4-RPPREFIXINCONST1 4-Warning RP prefix for [chars]/[dec] in FIB table [chars] inconsistent on slot [chars] - [chars] [[chars]] - - - COMMON_FIB-4-RPPREFIXINCONST2 4-Warning RP missing prefix for [inet]%m in FIB table [chars] present in routing table [[chars]] A passive consistency checker discovered a prefix in the routing table which is not present in the CEF forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-RPPREFIXINCONST2 4-Warning RP missing prefix for [inet]%m in FIB table [chars] present in routing table [[chars]] A passive consistency checker discovered a prefix in the routing table which is not present in the CEF forwarding table on the RP. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-RPPREFIXINCONST3 4-Warning RP has prefix [chars]/[dec] in FIB table [chars] missing in routing table A passive consistency checker discovered a prefix in the CEF forwarding table which is not present in the routing table. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-RPPREFIXINCONST3 4-Warning RP has prefix [chars]/[dec] in FIB table [chars] missing in routing table A passive consistency checker discovered a prefix in the CEF forwarding table which is not present in the routing table. This may be a transient condition. COMMON_FIB_DDTS_COMPONENT "If the same prefix gives repeated errors check the prefix in CEF and " "routing table. Try disable/enable CEF if the prefix is " "missing." COMMON_FIB-4-SB_STAT_ENCODE 4-Warning Encoding of [chars] [chars] stats XDR too big COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-SB_STAT_ENCODE 4-Warning Encoding of [chars] [chars] stats XDR too big COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-TOPO_STAT_ID_MGR 4-Warning Id manager error [chars]. Topology statistics accounting may not show the correct result COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4-TOPO_STAT_ID_MGR 4-Warning Id manager error [chars]. Topology statistics accounting may not show the correct result COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_FIB-4- UNEQUAL 4-Warning Ratio of unequal path weightings [chars] prevents oce [chars] from being used. - - - COMMON_FIB-4- UNEQUAL 4-Warning Ratio of unequal path weightings [chars] prevents oce [chars] from being used. - - - COMMON_FIB-5-FIB_RRP_HEADLESS_MODE 5-Notice %S The RRP lost communication with the RP but the platform still wants CEF\n\ to continue operating in headless mode. - LOG_STD_ACTION COMMON_FIB-5-FIB_RRP_HEADLESS_MODE 5-Notice %S The RRP lost communication with the RP but the platform still wants CEF\n\ to continue operating in headless mode. - LOG_STD_ACTION COMMON_FIB-6-FIB_GSB_TEST_MSG 6-Information Test subblock error: [chars] The subblock test command could not be completed successfully COMMON_FIB_DDTS_COMPONENT LOG_STD_NO_ACTION COMMON_FIB-6-FIB_GSB_TEST_MSG 6-Information Test subblock error: [chars] The subblock test command could not be completed successfully COMMON_FIB_DDTS_COMPONENT LOG_STD_NO_ACTION COMMON_FIB-6- FIB_RECURSION 6-Information [chars] has too many [dec] levels of recursion during [chars] - - - COMMON_FIB-6- FIB_RECURSION 6-Information [chars] has too many [dec] levels of recursion during [chars] - - - COMMON_MFIB-3-ASSERT 3-Error Assertion '[chars]' failed in [chars] MFIB [0x%08x]: [chars] [chars][chars]. COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-ASSERT 3-Error Assertion '[chars]' failed in [chars] MFIB [0x%08x]: [chars] [chars][chars]. COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-BG_POPULATE 3-Error MFIB master background process failed to populate tables for [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-BG_POPULATE 3-Error MFIB master background process failed to populate tables for [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-BROKER_ENCODE 3-Error [chars] broker failed to encode msg type [dec] for slots [chars] - - - COMMON_MFIB-3-BROKER_ENCODE 3-Error [chars] broker failed to encode msg type [dec] for slots [chars] - - - COMMON_MFIB-3-BROKERINITFAIL 3-Error Failed to initialise [chars] RP broker facility COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-BROKERINITFAIL 3-Error Failed to initialise [chars] RP broker facility COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-EPOCH 3-Error Failed to [chars] table [chars][chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-EPOCH 3-Error Failed to [chars] table [chars][chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-ILLEGAL_TABLEID 3-Error Attempt to create [chars] table with illegal tableid [dec] [chars] - - - COMMON_MFIB-3-ILLEGAL_TABLEID 3-Error Attempt to create [chars] table with illegal tableid [dec] [chars] - - - COMMON_MFIB-3- ILLEGALARGS 3-Error Illegal arguments - [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3- ILLEGALARGS 3-Error Illegal arguments - [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-INVALID_AF 3-Error Invalid address family [dec][chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-INVALID_AF 3-Error Invalid address family [dec][chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIB_GSB 3-Error Generic subblock error: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIB_GSB 3-Error Generic subblock error: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBISSU_REGISTRATION 3-Error Unable to register [chars] ISSU client[dec]. - - - COMMON_MFIB-3-MFIBISSU_REGISTRATION 3-Error Unable to register [chars] ISSU client[dec]. - - - COMMON_MFIB-3-MFIBXDR_ISSUREGERROR 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBXDR_ISSUREGERROR 3-Error ISSU client [chars] [dec] entity [dec] failed ISSU registration: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBXDRINV 3-Error Invalid XDR format. [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBXDRINV 3-Error Invalid XDR format. [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBXDRLEN 3-Error Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-MFIBXDRLEN 3-Error Invalid XDR length. Type [dec] [chars]. XDR/buffer len [dec]/[dec] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-NO_TABLE_NAME 3-Error Attempt to clear the name of [chars] table with tableid %p previous name [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-NO_TABLE_NAME 3-Error Attempt to clear the name of [chars] table with tableid %p previous name [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-NOBROKER 3-Error [chars] distribution broker not found - distributing [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-NOBROKER 3-Error [chars] distribution broker not found - distributing [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3- NOMEM 3-Error Memory allocation failure for [chars] in [chars] MFIB [0x%08x]. An attempt to allocate memory has failed. Depending on the criticality of the data to be stored MFIB operation may be impacted. COMMON_MFIB_DDTS_COMPONENT "Verify that the configuration is supported by the memory present in " "the system. Copy the message exactly as it appears and report it " "to your technical support representative." COMMON_MFIB-3- NOMEM 3-Error Memory allocation failure for [chars] in [chars] MFIB [0x%08x]. An attempt to allocate memory has failed. Depending on the criticality of the data to be stored MFIB operation may be impacted. COMMON_MFIB_DDTS_COMPONENT "Verify that the configuration is supported by the memory present in " "the system. Copy the message exactly as it appears and report it " "to your technical support representative." COMMON_MFIB-3-TABLE 3-Error [chars]: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-3-TABLE 3-Error [chars]: [chars] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-4-BROKERINVMSG 4-Warning Invalid message: [chars] type [chars] len [dec] An invalid message has been received by this broker. mfib LOG_STD_ACTION COMMON_MFIB-4-BROKERINVMSG 4-Warning Invalid message: [chars] type [chars] len [dec] An invalid message has been received by this broker. mfib LOG_STD_ACTION COMMON_MFIB-4-DISABLING 4-Warning [chars] MFIB is being disabled due to a fatal error. COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-4-DISABLING 4-Warning [chars] MFIB is being disabled due to a fatal error. COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-4-MFIBMSG 4-Warning Invalid message received. Type [chars] event/sub-type [dec] length [dec] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-4-MFIBMSG 4-Warning Invalid message received. Type [chars] event/sub-type [dec] length [dec] COMMON_MFIB_INTERNAL_ERROR COMMON_MFIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_MFIB-4-MFIBTABLE 4-Warning Failed to [chars] table [chars] [chars] An MFIB table was found to be missing when attempting to perform a change to it. This may be a transient condition COMMON_MFIB_DDTS_COMPONENT "If the same table gives repeated warnings or generates more serious" "errors copy the message exactly as it appears and report it to " "your technical support representative" COMMON_MFIB-4-MFIBTABLE 4-Warning Failed to [chars] table [chars] [chars] An MFIB table was found to be missing when attempting to perform a change to it. This may be a transient condition COMMON_MFIB_DDTS_COMPONENT "If the same table gives repeated warnings or generates more serious" "errors copy the message exactly as it appears and report it to " "your technical support representative" COMMON_MFIB-4-MFIBXDR_NOTREG 4-Warning XDR client [chars] should be registered. - - - COMMON_MFIB-4-MFIBXDR_NOTREG 4-Warning XDR client [chars] should be registered. - - - COMMON_MFIB-4-MFIBXDR_REGISTRATION 4-Warning Unable to register XDR client [chars]. - - - COMMON_MFIB-4-MFIBXDR_REGISTRATION 4-Warning Unable to register XDR client [chars]. - - - COMMON_SADR-3-DEPENDENCY_WALK 3-Error Walk specification %p missing handler for type [dec] dependency COMMON_SADR_INTERNAL_ERROR COMMON_SADR_DDTS_COMPONENT LOG_STD_ACTION COMMON_SADR-3-DEPENDENCY_WALK 3-Error Walk specification %p missing handler for type [dec] dependency COMMON_SADR_INTERNAL_ERROR COMMON_SADR_DDTS_COMPONENT LOG_STD_ACTION COMMON_SADR-3-FIBSADRDEPDUMP 3-Error [chars] COMMON_SADR_INTERNAL_ERROR COMMON_SADR_DDTS_COMPONENT LOG_STD_ACTION COMMON_SADR-3-FIBSADRDEPDUMP 3-Error [chars] COMMON_SADR_INTERNAL_ERROR COMMON_SADR_DDTS_COMPONENT LOG_STD_ACTION COMMON_TAL-3- HOSTBITSSET 3-Error Host bits set for [chars]/[dec]. TAL API has been called with prefix/len pair with host bits set. This prefix/len pair is invalid and indicates an error in the calling code. COMMON_TAL_DDTS_COMPONENT "Copy the message exactly as it appears and report it " "to your technical support representative." COMMON_TAL-3- HOSTBITSSET 3-Error Host bits set for [chars]/[dec]. TAL API has been called with prefix/len pair with host bits set. This prefix/len pair is invalid and indicates an error in the calling code. COMMON_TAL_DDTS_COMPONENT "Copy the message exactly as it appears and report it " "to your technical support representative." COMMON_UID-3-CFC_UID_CLIENT_EVENT 3-Error Event [chars] for [chars] %p UID:[chars] - [chars] - - - COMMON_UID-3-CFC_UID_CLIENT_EVENT 3-Error Event [chars] for [chars] %p UID:[chars] - [chars] - - - COMMON_UID-3-CFC_UID_CLIENT_KEY_TYPE_UNKNOWN 3-Error Unexpected key type <[chars]> for [chars] [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-CFC_UID_CLIENT_KEY_TYPE_UNKNOWN 3-Error Unexpected key type <[chars]> for [chars] [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-CFC_UID_CLIENT_MAP_EXISTS_FAIL 3-Error <[chars]> already mapped to [chars] [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-CFC_UID_CLIENT_MAP_EXISTS_FAIL 3-Error <[chars]> already mapped to [chars] [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-CLIENT_KEY 3-Error Client key error [chars]: [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-CLIENT_KEY 3-Error Client key error [chars]: [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_CK_DB_TREE_OP_FAIL 3-Error AVL tree [chars] failed for UID [dec] Client Key [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_CK_DB_TREE_OP_FAIL 3-Error AVL tree [chars] failed for UID [dec] Client Key [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_CLIENT_KEY_DB 3-Error UID [dec] Client key [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_CLIENT_KEY_DB 3-Error UID [dec] Client key [chars] - [chars] COMMON_FIB_INTERNAL_ERROR COMMON_FIB_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_DELETE_ALL_CK_FAIL 3-Error Failed to delete all client keys for UID [dec] - [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_DELETE_ALL_CK_FAIL 3-Error Failed to delete all client keys for UID [dec] - [chars] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_HASH_TBL_OP_FAIL 3-Error Hash table [chars] failed for UID [dec] Hash Tbl 0x[hec] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMMON_UID-3-UID_HASH_TBL_OP_FAIL 3-Error Hash table [chars] failed for UID [dec] Hash Tbl 0x[hec] COMMON_UID_INTERNAL_ERROR COMMON_UID_DDTS_COMPONENT LOG_STD_ACTION COMP_API-4-COMP_API_IDB_WARNING 4-Warning Incorrect External interface field access API invocation A routine external to the IP Multicast Component accesses an\n\ interface field with invalid interface argument - "An inconsistency calling an IP Multicast interface access API occurred." LOG_STD_ACTION COMP_API-4-COMP_API_IDB_WARNING 4-Warning Incorrect External interface field access API invocation A routine external to the IP Multicast Component accesses an\n\ interface field with invalid interface argument - "An inconsistency calling an IP Multicast interface access API occurred." LOG_STD_ACTION COMP_MATRIX-3-PRST_VBL_DELETE 3-Error ISSU Compatibility Matrix was unable to delete a persistent variable from the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_DELETE 3-Error ISSU Compatibility Matrix was unable to delete a persistent variable from the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_DELETE 3-Error ISSU Compatibility Matrix was unable to delete a persistent variable from the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_GET 3-Error ISSU Compatibility Matrix was unable to read a persistent variable from the local system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_GET 3-Error ISSU Compatibility Matrix was unable to read a persistent variable from the local system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_GET 3-Error ISSU Compatibility Matrix was unable to read a persistent variable from the local system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_WRITE 3-Error ISSU Compatibility Matrix was unable to write to persistent variables on the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_WRITE 3-Error ISSU Compatibility Matrix was unable to write to persistent variables on the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-3-PRST_VBL_WRITE 3-Error ISSU Compatibility Matrix was unable to write to persistent variables on the [chars] system rc = [dec]. The ISSU compatibility matrix was unable to access a persistent variable. There is no way to determine if issu image-version compatibility checking should be enabled or disabled. ha-issu-infra "show persistent variable" COMP_MATRIX-4-DISABLED 4-Warning Compatibility Matrix has been disabled. No image compatibility checking will be done. The ISSU compatibility matrix check has been disabled via configuration command no service image-version compatibility. When the standby comes up no image compatibility checking will be done which results in SSO redundancy mode even if the active and standby are running different images. ha-issu-infra "The ISSU compatibility matrix check has been disabled " "using the global configuration command " "no service image-version compatibility." "Redundancy mode would be SSO. " "Please be sure this is your intention or change configuration " "using service image-version compatibility." COMP_MATRIX-4-DISABLED 4-Warning Compatibility Matrix has been disabled. No image compatibility checking will be done. The ISSU compatibility matrix check has been disabled via configuration command no service image-version compatibility. When the standby comes up no image compatibility checking will be done which results in SSO redundancy mode even if the active and standby are running different images. ha-issu-infra "The ISSU compatibility matrix check has been disabled " "using the global configuration command " "no service image-version compatibility." "Redundancy mode would be SSO. " "Please be sure this is your intention or change configuration " "using service image-version compatibility." COMP_MATRIX-4-DISABLED 4-Warning Compatibility Matrix has been disabled. No image compatibility checking will be done. The ISSU compatibility matrix check has been disabled via configuration command no service image-version compatibility. When the standby comes up no image compatibility checking will be done which results in SSO redundancy mode even if the active and standby are running different images. ha-issu-infra "The ISSU compatibility matrix check has been disabled " "using the global configuration command " "no service image-version compatibility." "Redundancy mode would be SSO. " "Please be sure this is your intention or change configuration " "using service image-version compatibility." COMP-3-BADCOMP 3-Error Interface [chars] Bad status returned from packet compression operation An internal software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." COMP-3-COMPERR 3-Error [chars]: COMPRESS: stac error! status: [dec] size in: [dec] size out: [dec] An internal software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." COMP-3-CONFIGBAD 3-Error Interface [chars] Compression internal configuration error An internal software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." COMP-3-SIZEBAD 3-Error Interface [chars] Decompression size error One interface is configured for predictor compression the other is\n\ not. - "Configure both interfaces for predictor compression." COMP-3-SUBBLOCKERR 3-Error Interface [chars] compression subblock creation failed. An internal software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." COMP-3-SYNCBAD 3-Error Interface [chars] Decompression sync error One interface is configured for predictor compression the other is\n\ not. - "Configure both interfaces for predictor compression." COMP-3-VERSIONBAD 3-Error Interface [chars] Compression Version mismatch expected [hec] received [hec] One interface is configured for predictor compression the other is\n\ not. - "Configure both interfaces for predictor compression." COMP-5-NOBUF 5-Notice Interface [chars] [chars] Interface serial0 compression getbuffer failed causing Link Access\n\ Procedure Balanced LAPB retransmissions. - "Configure additional large and big buffers." COMPILED_ACL-2-LIST_CREATE 2-Critical [chars]: failed to create row queue for node [dec] Turbo ACL has been disabled temporarily The system encountered an error while initializing a data structure required for the correct operation of Turbo ACL processing. Turbo ACL will be disabled until another recompilation has completed successfully. c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-2-QUEUE_INIT 2-Critical [chars]: failed to initialize back-pointer list for row [dec] in node [dec] Turbo ACL has been disabled temporarily The system encountered an error while initializing a data structure required for the correct operation of Turbo ACL processing. Turbo ACL will be disabled until another recompilation has completed successfully. c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-3-INTERNAL_ERROR 3-Error an unexpected internal error occured: [chars] An unexpected internal error occurred. This error may result in one or more flows being punted to the RP or in Turbo ACL not functioning. c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BACKPOINTER_OVERFLOWED_NOT_EMPTY 4-Warning [chars]: the back-pointer list for row [dec] in node [dec] is marked as overflowed but is not empty EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BACKPOINTER_OVERFLOWED_NOT_EMPTY_REFERENCES 4-Warning [chars]: the back-pointer list for row [dec] in node [dec] is marked as overflowed but is not empty EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BACKPOINTER_PROCESSING_OVERFLOWED 4-Warning [chars]: processing back-pointers in row [dec] in node [dec] but the list is marked as overflowed EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BACKPOINTER_WRONG 4-Warning [chars]: entry at row [dec] column [dec] in node [dec] does not reference row [dec] in the node's child EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BAD_PROCESS_REFERENCES 4-Warning [chars]: error while processing references for row [dec] in node [dec]: [chars] EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-BAD_ROW_FREE 4-Warning [chars]: cannot free row [dec] in node [dec]: [chars] EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-DEFERRED_ENTRY_CONSISTENCY 4-Warning [chars]: while [chars] in row [dec] in node [dec] found deferred entry bitmap is [chars] but count is [dec] EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-ENTRY_COUNT 4-Warning [chars]: row entry counters not allocated for node [dec] while freeing row [dec] EXPLANATION_INTERNAL_CONSISTENCY_ERROR EXPLANATION_IMPACT_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-ROW_UPDATE 4-Warning [chars]: cannot process row queue update for row [dec] in node [dec]: [chars] EXPLANATION_INTERNAL_ERROR EXPLANATION_IMPACT_POSSIBLE_PUNTING c7300-pxf RECOMMENDED_ACTION COMPILED_ACL-4-ROW_UPDATE_ENQUEUE 4-Warning [chars]: cannot process row queue update for row [dec] in node [dec]: enqueue failed %lu/%lu entries list is [chars]valid entry is [chars]enqueued - - - COMPILED_ACL-5-LIST_INFO 5-Notice [chars]: failed to set list information function for node [dec]'s row queue ID [dec] The system encountered an error while initializing a function vector used for debugging purposes. Turbo ACL will continue to function correctly but the show list ID command will not show Turbo ACL-specific information for the specified list ID number. c7300-pxf RECOMMENDED_ACTION COND_DEBUG_HA-2-GET_BUFFER 2-Critical COND_DEBUG ISSU client failed to get buffer for message. Error: [dec] [chars] The COND_DEBUG HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. cond_debug "show logging and show checkpoint client" COND_DEBUG_HA-2-INIT 2-Critical COND_DEBUG ISSU client initialization failed to [chars]. Error: [dec] [chars] The COND_DEBUG ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. cond_debug LOG_STD_ACTION COND_DEBUG_HA-2-SEND_NEGO_FAILED 2-Critical COND_DEBUG ISSU client failed to send negotiation message. Error: [dec] [chars] The COND_DEBUG ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. cond_debug "show logging and show checkpoint client" COND_DEBUG_HA-2-SESSION_NEGO 2-Critical COND_DEBUG ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The COND_DEBUG ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. cond_debug "show issu session and " "show issu negotiated capability " COND_DEBUG_HA-2-SESSION_REGISTRY 2-Critical COND_DEBUG ISSU client failed to register session information. Error: [dec] [chars] The COND_DEBUG ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. cond_debug "show issu capability entries and " "show issu session and " "show issu negotiated capability " COND_DEBUG_HA-3-INVALID_SESSION 3-Error COND_DEBUG ISSU client does not have a valid registered session. The COND_DEBUG ISSU client does not have a valid registered session. cond_debug "show issu capability entries and " "show issu session and " "show issu negotiated capability " COND_DEBUG_HA-3-MSG_SIZE 3-Error COND_DEBUG ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The COND_DEBUG ISSU client failed to calculate the MTU for the specified message. The COND_DEBUG ISSU client will not able to send the message to the standby device. cond_debug "show issu message group and " "show issu session and " "show issu negotiated version " COND_DEBUG_HA-3-SESSION_UNREGISTRY 3-Error COND_DEBUG ISSU client failed to unregister session information. Error: [dec] [chars] The COND_DEBUG ISSU client failed to unregister session information. cond_debug "show issu session and " "show issu negotiated capability " COND_DEBUG_HA-3-TRANSFORM 3-Error COND_DEBUG ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The COND_DEBUG ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the COND_DEBUG state between the active device and the standby device is not identical. cond_debug "show issu session and " "show issu negotiated version " CONF_SW-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the CONF SW feature failed. This will cause the feature not to function. The function cpp-conf-sw "This is normally a software issue. " "The consequences are that the CONF SW feature will not function. " LOG_STD_ACTION CONF_SW-3-FEAT_DOWN 3-Error Invalid request [chars] while feature down conf id [dec] While the feature was not active an invalid request was received from another layer of the CONF_SW software stack for the specified conf ID. Some requests do not have an associated conf ID. For them the displayed conf ID is zero. cpp-conf-sw "This is a software issue. The consequences " "could be limited to only one or a few confs. " LOG_STD_RECUR_ACTION CONF_SW-3-FEAT_UP 3-Error Invalid request [chars] while feature up While the feature was active an invalid request was received from another layer of the CONF SW software stack. cpp-conf-sw "This is a software issue. " "There are no consequences as this can only have been an Init request " "while the feature was already active. " LOG_STD_RECUR_ACTION CONF_SW-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper CONF SW software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck conf that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations. cpp-conf-sw "This is normally a software issue. " LOG_STD_RECUR_ACTION CONF_SW-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper CONF SW software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck conf that cannot be established etc. In rare cases this could also affect other operations such as feature activation deactivation modification High-Availability switchover operations. cpp-conf-sw "This is normally a software issue. " LOG_STD_RECUR_ACTION CONF_SW-3-NO_RES 3-Error [chars] resource not available for the [chars] request conf id [dec] The specified software resource was not available or could not be located for the specified request from upper CONF SW software stack layers for the specified conf ID. cpp-conf-sw "This is a software issue. The consequences " "are that the specified request could not be performed. " LOG_STD_RECUR_ACTION CONFIG_CSRLXC-2-INIT_FAILED 2-Critical CSRLXC configuration cannot occur: [chars] The system was unable to even attempt to apply LXC configuration for the given reason. ultra-ui LOG_STD_SH_TECH_ACTION CONFIG_CSRLXC-3-CONFIG_NOT_SAVED 3-Error Configuration not saved to NVRAM. Please inspect [chars] for details. Out of the generated VM configuration commands the given number of commands were rejected by the IOSd parser. The configuration is only automatically saved to NVRAM if no errors are encountered so in this case it was not saved. The indicated log file will describe exactly which commands were rejected as will any accompanying CSRLXC-4-CLI_FAILURE messages in this log. ultra-ui "Inspect the current running-config of the router " "using the show running-config " "command. If it appears valid you may manually save " "the configuration using copy running-" "config startup-config. If it does not " "appear valid manually correct the configuration " "or use the config replace nvram:startup-" "config command to revert to the " "startup-config." CONFIG_CSRLXC-3-FILE_ERROR 3-Error Could not [chars] file [chars]: [chars] The system was unable to perform the indicated operation on the indicated file for the indicated reason ultra-ui "Make sure the given disk is correctly formatted " "and has sufficient free space available." CONFIG_CSRLXC-4-CLI_FAILURE 4-Warning Configuration command failure: '[chars]' was rejected The indicated IOSd configuration command generated by the CSRLXC subsystem was rejected by the IOSd CLI. Look for a subsequent CSRLXC-3-CONFIG_NOT_SAVED log message which will contain a reference to a logfile containing more information about this failure. ultra-ui "Inspect the log file to determine why the command " "was rejected and how to correct it. If necessary " "manually re-issue the corrected command." CONFIG_CSRLXC-5-CONFIG_DONE 5-Notice Configuration was applied and saved to NVRAM. See [chars] for more details. The generated configuration was successfully applied no commands were rejected by the IOSd CLI and the ultra-ui LOG_STD_NO_ACTION CONFIG-3-VFI 3-Error ERRMSG_NOFLAGS - - - CONFIG-3-VFI 3-Error ERRMSG_NOFLAGS - - - CONFIG-3-XCONNECT 3-Error ERRMSG_FLAG_TRACEBACK - - - CONFIG-3-XCONNECT 3-Error ERRMSG_FLAG_TRACEBACK - - - CONFIG-4-ATOM_TRANS 4-Warning ERRMSG_NOFLAGS - - - CONFIG-4-ATOM_TRANS 4-Warning ERRMSG_NOFLAGS - - - CONSISTENCY-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - CONSISTENCY-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - CONSISTENCY-3-LCON 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-LCON 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-LDP 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-LDP 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-MPLS_TE 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-MPLS_TE 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-MPLS_TE_LM 3-Error ERRMSG_FLAG_TRACEBACK - - - CONSISTENCY-3-MPLS_TE_LM 3-Error ERRMSG_FLAG_TRACEBACK - - - CONST_ISSU-2-NEGO_NOT_DONE 2-Critical [chars][dec]: ISSU Negotiation not complete Unable to complete ISSU negotiation. CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CAP_EXCHANGE 3-Error [chars][dec]: Capability exchange failed with error [chars] The capability exchange failed the ISSU client is unable to process the received capability CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CAP_REG 3-Error [chars][dec]: failed to register The capabilities of the ISSU client could not be registered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CAPENTRY_REG 3-Error [chars][dec]: failed to register a capability entry [chars] The ISSU client failed to register a capability entry CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CAPGROUP_REG 3-Error [chars][dec]: failed to register a capability group [chars] The ISSU client failed to register a capability group CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CAPTYPE_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a capability type CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CF_SEND 3-Error [chars][dec]: Client failed to send message [dec] ISSU client cannot send a negotiation message to a peer CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CLIENT_REG 3-Error [chars][dec]: Client failed to register [chars] The ISSU Client could not be registered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CLIENT_REG_FAILED 3-Error [chars][dec]: Client is not The ISSU Client is not yet initialized. The negotiation for this client is not yet done. CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-CONST_MTU_NOT_ENOUGH 3-Error [chars][dec]: Requested buffer size [dec] is greater than the max MTU size Checkpoint buffer size requested is greater than the max MTU size checkpoint supports cat6000-ha LOG_STD_ACTION CONST_ISSU-3-ENTITY_REG 3-Error [chars][dec]: failed to register The ISSU entity could not be registered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-ENTITY_UNREG 3-Error [chars][dec]: failed to unregister The ISSU entity could not be unregistered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-ICC_SEND 3-Error [chars][dec]: Client failed to send message ISSU client cannot send a negotiation message to a peer CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-MSG_MTU 3-Error [chars][dec]: Client failed to get mtu for message [dec] [chars] [chars][dec]: client cannot get the MTU for a message type CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-MSG_NOT_OK 3-Error [chars][dec]: ISSU message type [dec] is not compatible ISSU received a message not compatible with the running version. CONST_ISSU_PLATFORM "show message type " CONST_ISSU-3-MSG_POLICY 3-Error [chars][dec]: Client failed to negotiate version for message type [dec] error [chars] ISSU client cannot negotiate message to a peer CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-MSG_REG 3-Error [chars][dec]: failed to register its messages [chars] Messages for the ISSU client could not be registered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-MSGGROUP_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a message group CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-MSGTYPE_REG 3-Error [chars][dec]: failed to register a message type [chars] The ISSU client failed to register a message type CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-NEGO_PROCESS 3-Error [chars][dec]: Cannot create process: [chars] The process to negotiate the session for the specified ISSU client cannot be created. CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-SESSION_REG 3-Error [chars][dec]: session failed to register [chars] The client's ISSU session could not be registered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-SESSION_UNREG 3-Error [chars][dec]: session [dec] The client's ISSU session could not be unregistered CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-START_NEGO_FAILED 3-Error [chars][dec]: failed to The ISSU client cannot start its negotiation CONST_ISSU_PLATFORM LOG_STD_ACTION CONST_ISSU-3-TRANSFORM_FAILED 3-Error [chars][dec]: [chars] transformation failed [chars] The transformation operation for the ISSU message has failed CONST_ISSU_PLATFORM LOG_STD_ACTION CONTROLLER-2-CDB_NULL 2-Critical cdb is NULL A NULL pointer is detected - LOG_STD_SH_TECH_ACTION CONTROLLER-2-CRASHED 2-Critical Interface Processor in slot [dec] not responding [hec]: shutting it down A controller stopped responding to commands over the cBus so it was\n\ put into shutdown mode. - "Re-enable the controllers by issuing the no shut\n\ configuration command on all controllers on the card or\n\ hotswap out the bad card and install the new one. You must\n\ still manually no shut the controllers." CONTROLLER-2-DSX_NULL 2-Critical dsx pointer is NULL A NULL pointer is detected - LOG_STD_SH_TECH_ACTION CONTROLLER-2-FIRMWARE 2-Critical Controller [chars] [chars] A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION CONTROLLER-2-NOTFOUND 2-Critical For controller [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION CONTROLLER-4-ACR_DCR_CLOCK_DS1 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec] [chars] DS1 Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_DS3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec] [chars] DS3 Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_DS3_CHANNEL 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec] [chars] DS3:channelized Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_OCN_CT3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars] OCN_CT3: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_OCN_T3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec] [chars] OCN_T3: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_OCN_VT_T1 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars] OCN_VT_T1: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_STMN_CT3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars] STMN_CT3: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_STMN_E3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars] STMN_E3: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_STMN_T3 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec] [chars] STMN_T3: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-4-ACR_DCR_CLOCK_STMN_VC1x 4-Warning [chars]: [chars] Clock status is [chars] for clock_id [dec] on circuit: [dec]/[dec]/[dec]/[dec] [chars] STMN_VC1x: Recovered clock status change message - LOG_STD_NO_ACTION CONTROLLER-5-CALLDROP 5-Notice Controller [chars] [chars] A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CONTROLLER-5-CLOCKSTATE 5-Notice Controller [chars] [chars] A configurable controller clock changed its state. - LOG_STD_NO_ACTION CONTROLLER-5-DOWNDETAIL 5-Notice Controller [chars] changed state to [chars] due to [chars] A configurable controller changed its state. - LOG_STD_NO_ACTION CONTROLLER-5-HDLC_INSUFF_RESOURCE 5-Notice Insufficient HDLC resources to enable channel [dec] Limited number of HDLC channels can be allocated for this trunk - "Please check the number of HDLC resources supported for this trunk\n\ card. Please contact your technical support representative." CONTROLLER-5-LOOPSTATUS 5-Notice Controller [chars] [chars] A configurable controller loopback status. - LOG_STD_NO_ACTION CONTROLLER-5-REMLOCALLOOP 5-Notice Controller [chars] local loop [chars] [chars] A configurable controller entered local loopback. - LOG_STD_NO_ACTION CONTROLLER-5-REMLOOP 5-Notice Controller [chars] remote loop [chars] [chars] A configurable controller entered remote loopback. - LOG_STD_NO_ACTION CONTROLLER-5-UPDOWN 5-Notice Controller [chars] changed state to [chars] A configurable controller changed its state. - LOG_STD_NO_ACTION COPTMONMIB-3-ENTRYADDFAILED 3-Error Registering of the interface with ifIndex [dec] to local data structure failed An attemt to make an entry for the registering interface failed gsr-netmgmt "" COPTMONMIB-3-ENTRYPRESENT 3-Error An entry is already present for the registering interface with ifIndex [dec] An entry in the OPTICAL MONITORING MIB is already existing for the registering interface gsr-netmgmt "" CORABI-3-FATAL_N10G_ERP_ERROR 3-Error ERP errors: [chars] ERP error data: 0x%02x ERP error phase: 0x%01x ERP error addr: 0x%08x Fatal Corabi N10G ERP interrupt cmts-platform "Copy the error message exactly as it appears and report it to your" " technical support" CORABI-3-FATAL_N10G_FAULT 3-Error N10G fault reported Fatal Corabi N10G Fault interrupt cmts-platform "Copy the error message exactly as it appears and report it to your" " technical support" Corrupt configuration unsupported [chars] [dec] encountered The OC3/STM1 RP driver running configuration is corrupt c7600-sip-200 "This is a internal software error. Decode the " "traceback and get the output of show " "running-config. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with " "the output of show tech " "details" - - CPP_BQS_QMOVE-3-PROXY_COMPLETE 3-Error Proxy Operation: [chars] Operation that was flagged as timed out has now completed qfp-bqs-internal LOG_STD_ACTION CPP_BQS_QMOVE-3-PROXY_ERROR 3-Error Proxy Operation Failed: [chars] BQS Proxy operation failed. qfp-bqs-internal LOG_STD_ACTION CPP_BQS_QMOVE-3-PROXY_TIMEOUT 3-Error Proxy Operation: [chars] node_id [hec] data [hec] data [hec] BQS Proxy operation timeout. Proxy will continue to retry operatin. qfp-bqs-internal LOG_STD_ACTION CPP_BQS-2-MPASS_FS_REG 2-Critical CPP BQS PROXY feature special vector [dec] registration failed result: [dec] Cisco internal software error. CPP multipass registration of a feature special processing vector for BQS Proxy failed. The BQS proxy will not be fully functional while this condition exists. cpp-ucode LOG_STD_ACTION CPP_BQS-2-PROXY_IPC_INIT_FAILED 2-Critical CPP BQS Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. CPP BQS initialization detected that the Proxy IPC interface initialization failed. The BQS Proxy will not be functional while this condition exists. cpp-ucode LOG_STD_ACTION CPP_BQS-3-CARVE 3-Error [chars]: size [dec] SW carved out memory region initialization failed. A BQS proxy failed to initialize the software memory region. cpp-ucode LOG_STD_ACTION CPP_BQS-3-CMD_ACTIVE 3-Error CPP BQS Proxy Command correlator [dec] A BQS Proxy command was received but the correlator was still in use. Commad was not processed. cpp-ucode LOG_STD_ACTION CPP_BQS-3-INIT_FAILED 3-Error CPP BQS RM Proxy region [chars] BQS proxy failed due initialize or resize software managed memory. cpp-ucode LOG_STD_ACTION CPP_BQS-3-INVALID_SUBTYPE 3-Error CPP BQS RM Proxy subtype [dec] BQS proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer. cpp-ucode LOG_STD_ACTION CPP_BQS-3-MAX_GPM_TX_LEN_EXCEED 3-Error CPP BQS Proxy Command exceed GPM tx len [dec] A BQS Proxy command recycle a packet exceed GPM tx len cpp-ucode LOG_STD_ACTION CPP_BQS-3-PROXY_IPC_SEND 3-Error failure: [chars] BQS Proxy send response failed response was dropped. cpp-ucode LOG_STD_ACTION CPP_BQS-3-RESIZE 3-Error CPP BQS Proxy Memory Manager region [chars] BQS proxy failed to resize software managed memory. cpp-ucode LOG_STD_ACTION CPP_CONF_SW-4-CPP_CONF_SW_NULL_EXMEM 4-Warning Unexpected NULL shared-local EXMEM handle - ref_count [dec] The error will be corrected and pinhole programming will continue. asr1k-conf-sw LOG_STD_NO_ACTION CPP_FLOWDB_PROXY-3-FLOWDB_INIT_FAIL 3-Error flowdb proxy init failure rc= [dec] The flow database proxy has experienced a failure when trying to init csr1kv-dp-infra LOG_STD_ACTION CPP_FLOWDB_PROXY-3-FLOWDB_SEND_IPC_FAIL 3-Error rc= [dec] The flow database proxy has experience a failure when trying to send an IPC csr1kv-dp-infra LOG_STD_ACTION CPP_FLOWDB_PROXY-3-FLOWDB_UNEXPECTED_ERR 3-Error rc= [dec] The flow database proxy has experienced an unexpected condition csr1kv-dp-infra LOG_STD_ACTION CPP_FLOWDB_PROXY-3-INVALID_IPC_SUBTYPE 3-Error subtype is [dec] The flow database proxy has receive an IPC with an unexpected subtype csr1kv-dp-infra LOG_STD_ACTION CPP_FM-3-CPP_FM_CLIENT_WARNING 3-Error [chars] - - - CPP_FM-3-CPP_FM_FIPS_BYPASS_TEST 3-Error NIST bypass test failed for CPP_FM object [chars]. Classification Feature Manager Security Client database detected a discrepancy in a security sensitive object. This could be due to a hardware or software resouce limitation or a software defect. qfp-class-internal "Check the logs for information on the relevant " "object download states. Remove the object or a " "parent object in question. If the problem persists " "reboot the forwarding processor ESP." CPP_FM-3-CPP_FM_HW_TCAM_WARNING 3-Error HW TCAM limit exceeded: [chars] - - - CPP_FM-3-CPP_FM_SW_TCAM_WARNING 3-Error SW TCAM limit exceeded: [chars] - - - CPP_FM-3-CPP_FM_TCAM_CE_WARNING 3-Error [chars] - - - CPP_FM-3-CPP_FM_TCAM_WARNING 3-Error TCAM limit exceeded: [chars] - - - CPP_FM-4-CPP_FM_FIELD_IGNORED 4-Warning Matching on field type [dec] [chars] value [dec] 0x[hec] User is trying to use a classification criterion not supported by the feature. For example user is trying to apply a with a class matching matched on an IPv6 ACL that contains a match on flow-label. The entire rule e.g. ACE containing the unsupported criterion cpp-sw LOG_STD_NO_ACTION CPP_FM-4-CPP_FM_TCAM_MORE_INFO_WARNING 4-Warning TCAM limit exceeded: [chars] - - - CPP_FR-2-BQS_SCRATCH_TOOSMALL 2-Critical QFP BQS Scratch area too small for Frame Relay MFR feature usage size: [dec] need: [dec]. Cisco internal software error. QFP Frame Relay MFR initialization detected that the BQS scratch memory area is insufficient for Frame Relay MFR usage. The Frame Relay MFR Bundle interfaces will not be functional while this condition exists. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-2-PROXY_IPC_INIT_FAILED 2-Critical Frame Relay Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. FR initialization detected that the Proxy IPC interface initialization failed. The FR interfaces may not function properly while this condition exists. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-INV_PROXY_MSG 3-Error CPP FR Proxy received invalid IPC message ID [dec] Cisco internal software error. CPP FR Proxy received an invalid message ID. This message will be ignored. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-MFR_INVALID_RX_DLCI 3-Error Frame Relay MFR DLCI [dec] received from the peer Possible error on the peer device with Multilink FR. Received Multilink FR packet contained wrond DLCI number. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_DUP_DLCI_ID 3-Error QFP Frame Relay MFR Proxy [chars] [chars] duplicate DLCI [dec] for interface [chars] Cisco internal software error. QFP Frame Relay MFR Proxy message DLCI Add could not be processed for the indicated interface due use of a given DLCI on multiple member links within the same Frame Relay MFR Bundle. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_DUP_LINK_ID 3-Error QFP Frame Relay MFR Proxy [chars] [chars] duplicate Link ID [dec] for interface [chars] Cisco internal software error. QFP Frame Relay MFR Proxy message Link Add could not be processed for the indicated interface due use of a given Link ID on multiple member links within the same Frame Relay MFR Bundle. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_BUFFER_LIMIT 3-Error QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid Rx buffer limit Cisco internal software error. QFP Frame Relay MFR was provided a invalid Rx buffer limit value. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_BUNDLE_STATE 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid Bundle state [chars] [dec] for Cisco internal software error. QFP Frame Relay MFR Proxy message could not be processed due to the Frame Relay MFR Bundle being in an incorrect state to accept the message. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_DLCI_INFO 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid PVC Info Base: 0x%08x Num: [dec] Cisco internal software error. QFP Frame Relay MFR Proxy message contained invalid Frame Relay MFR PVC information. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_LINK_ID 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid Link ID [dec] for interface [chars] Cisco internal software error. QFP Frame Relay MFR Proxy message Link Add could not be processed for the indicated interface due to an invalid Link ID. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_LINK_STATE 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid Link state [chars] [dec] for Cisco internal software error. QFP Frame Relay MFR Proxy message could not be processed due to the Frame Relay MFR Link being in an incorrect state to accept the message. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_LOST_SEQ_TO 3-Error QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid lost sequence Cisco internal software error. QFP Frame Relay MFR was provided a invalid lost sequence timeout value. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_RX_TX_INTF_VALUE 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid Rx/Tx interface value [dec] for Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Bundle state change or configuration update due to an invalid interface Rx/Tx designation in the proxy request. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_INV_SUB_DEV_ID 3-Error QFP Frame Relay MFR Proxy [chars] [chars] invalid Sub-Device ID [dec] for interface [chars] Cisco internal software error. QFP Frame Relay MFR Proxy message Bundle Add could not be processed for the indicated interface due to an invalid Sub-Device ID. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-mlppp keyword:none LOG_STD_ACTION CPP_FR-3-PROXY_INV_TX_LINK_WEIGHT 3-Error QFP Frame Relay MFR Proxy [chars] [chars] indicated an invalid Tx Link weight Cisco internal software error. QFP Frame Relay MFR Proxy message contained invalid Tx Link weight information. The associated Frame Relay MFR Member Link and/or Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_IPC_ALLOC_FAIL 3-Error CPP Frame Relay Proxy response to msg id [dec] lost due to buffer allocation failure Cisco internal software error. CPP Frame Relay Proxy message processing detected a IPC buffer allocation failure during response processing. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_NULL_BUNDLE 3-Error QFP Frame Relay MFR Proxy [chars] [chars] NULL Bundle sub-block for Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Bundle state change or configuration update due to an invalid or uninitialized Bundle sub-block. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_NULL_DLCI 3-Error QFP Frame Relay MFR Proxy [chars] [chars] NULL PVC sub-block for Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Member PVC state change or configuration update due to an invalid or uninitialized PVC sub-block. The associated Frame Relay MFR PVC interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_NULL_LINK 3-Error QFP Frame Relay MFR Proxy [chars] [chars] NULL Member Link sub-block for Cisco internal software error. QFP Frame Relay MFR Proxy was unable to complete the requested Frame Relay MFR Member Link state change or configuration update due to an invalid or uninitialized Member Link sub-block. The associated Frame Relay MFR Member Link interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-3-PROXY_SID_UPDATE_COMPLETE_ERROR 3-Error QFP Frame Relay MFR Proxy [chars] SID Update Complete w/o Preceeding Lock Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected. cpp-ucode keyword:frame-realy LOG_STD_ACTION CPP_FR-3-PROXY_SID_UPDATE_LOCK_ERROR 3-Error QFP Frame Relay Proxy [chars] Multiple SID Update Locks to same interface Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected. cpp-ucode keyword:frame_relay LOG_STD_ACTION CPP_FR-4-PROXY_IPC_ALLOC_FAIL2 4-Warning QFP Frame Relay MFR Proxy [chars] response lost due to buffer allocation Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a IPC buffer allocation failure during proxy response processing. The associated Frame Relay MFR functionality may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-4-PROXY_SYNC 4-Warning QFP Frame Relay MFR Proxy [chars] [chars] Bundle/Link sync issue with interface [chars] Cisco internal software error. QFP Frame Relay MFR Proxy message processing detected a Bundle-Link state synchronization abnormality. This condition should be cosmetic. Full context of the message will aid in problem isolation. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_FR-4-TX_BUNDLE_FLOWED_OFF 4-Warning QFP Frame Relay MFR Tx Bundle [chars] flowed off for an abnormal duration due to one or more congested member links Possible Cisco internal software or hardware error. QFP Frame Relay MFR Tx processing detected that a Frame Relay MFR Bundle interface was flowed off for an extended period of time due to a congested member link queue. The associated Frame Relay MFR Bundle interface may not be fully functional as a result of this condition. cpp-ucode keyword:frame-relay LOG_STD_ACTION CPP_IPHC_PROXY-3-INVALID_IPC_INPUT 3-Error [chars] CPP IPHC Client Proxy failure IPHC proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer. cpp-ucode LOG_STD_ACTION CPP_LDN-2-PROXY_IPC_INIT_FAILED 2-Critical CPP LDN Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. CPP LDN initialization detected that the Proxy IPC interface initialization failed. The LDN Proxy will not be functional while this condition exists. cpp-ucode LOG_STD_ACTION CPP_LDN-3-PROXY_GPM_RSRC_FAIL 3-Error failure: [chars] LDN Proxy failed in performing a GPM operation. cpp-ucode LOG_STD_ACTION CPP_LDN-3-PROXY_IPC_INVALID 3-Error failure: [dec] LDN Proxy received an invalid IPC msg from the client. cpp-ucode LOG_STD_ACTION CPP_LDN-3-PROXY_IPC_SEND 3-Error failure: [chars] LDN Proxy send response failed response was dropped. cpp-ucode LOG_STD_ACTION CPP_LDN-3-PROXY_METAPKT_ENQ 3-Error subdevice id: [dec] failure: [dec] LDN Proxy metapacket enqueue failed. cpp-ucode LOG_STD_ACTION CPP_MPASS-3-INVALID_VECTOR 3-Error vector [dec] An invalid multipass vector was received cpp-ucode LOG_STD_ACTION CPP_NAT_PROXY-3-INVALID_IPC_SUBTYPE 3-Error subtype is [dec] The NAT proxy has receive an IPC with an unexpect subtype cpp-ucode LOG_STD_ACTION CPP_NAT_PROXY-3-NAT_INIT_FAIL 3-Error nat init failure rc= [dec] The NAT proxy has experience a failure when trying to init NAT cpp-ucode LOG_STD_ACTION CPP_NAT_PROXY-3-NAT_SEND_IPC_FAIL 3-Error rc= [dec] The NAT proxy has experience a failure when trying to send an IPC cpp-ucode LOG_STD_ACTION CPP_NAT64_PROXY-3-INVALID_IPC_SUBTYPE 3-Error subtype is [dec] The NAT64 proxy has received an IPC with an unexpected subtype cpp-ucode LOG_STD_ACTION CPP_NAT64_PROXY-3-NAT_INIT_FAIL 3-Error nat64 init failure rc= [dec] The NAT64 proxy has experience a failure when trying to init NAT64 cpp-ucode LOG_STD_ACTION CPP_NAT64_PROXY-3-NAT64_INIT_FAIL 3-Error nat64 init failure rc= [dec] The NAT proxy has experienced a failure when trying to initialize the NAT64 proxy cpp-ucode LOG_STD_ACTION CPP_NAT64_PROXY-3-NAT64_IPC_FAIL 3-Error rc= [dec] The NAT64 proxy has received an IPC with an unexpected format/data cpp-ucode LOG_STD_ACTION CPP_NAT66_PROXY-3-INVALID_IPC_SUBTYPE 3-Error subtype is [dec] The NAT66 proxy has received an IPC with an unexpected subtype cpp-ucode LOG_STD_ACTION CPP_NAT66_PROXY-3-NAT66_INIT_FAIL 3-Error nat66 init failure rc= [dec] The NAT proxy has experienced a failure when trying to initialize the NAT66 proxy cpp-ucode LOG_STD_ACTION CPP_NAT66_PROXY-3-NAT66_IPC_FAIL 3-Error rc= [dec] The NAT66 proxy has received an IPC with an unexpected format/data cpp-ucode LOG_STD_ACTION CPP_NGIO-3-NGIO_FC_BADPATH 3-Error NGIO flow control msg received on unexpected code path mod pid [dec] Flow control message received on unexpected code path cpp-ucode LOG_STD_RECUR_ACTION CPP_NGIO-3-NGIO_FC_IID 3-Error NGIO flow control ID lookup failed:[chars] module pid/iid:[dec]/[dec] Flow control message from module contained an invalid identification field cpp-ucode LOG_STD_RECUR_ACTION CPP_NGIO-3-NGIO_MOD_PID 3-Error NGIO flow control msg received with no config matching module pidmod pid:[dec] Flow control message received could not be matched with a module. cpp-ucode LOG_STD_RECUR_ACTION CPP_NGIO-5-NGIO_FC_PRIORITY 5-Notice NGIO flow control msg processed at reduced priority mod pid:[dec] Flow control message from module was not properly prioritized. cpp-ucode LOG_STD_ACTION CPP_NGIO-5-NGIO_PKT_PRIORITY 5-Notice NGIO packet processed at flow control priority mod pid:[dec] Data packet from module was not properly prioritized. cpp-ucode LOG_STD_ACTION CPP_PFR_PROXY-3-INVALID_IPC_SUBTYPE 3-Error subtype is [dec] The PfR proxy has receive an IPC with an unexpected subtype cpp-ucode LOG_STD_ACTION CPP_PFR_PROXY-3-PFR_INIT_FAIL 3-Error pfr init failure rc= [dec] The PFR proxy has experienced a failure when trying to init PFR cpp-ucode LOG_STD_ACTION CPP_PFR_PROXY-3-PFR_IPC_PAK_ALLOC_FAILED 3-Error rc= [dec] Allocation of PFR IPC response pkt failed cpp-ucode LOG_STD_ACTION CPP_PFR_PROXY-3-PFR_SEND_IPC_FAIL 3-Error rc= [dec] The PfR proxy has experienced a failure when trying to send an IPC cpp-ucode LOG_STD_ACTION CPP_PKT_SUBBLOCK-3-PKT_SB_MANAGE_FAIL 3-Error rc=0x[hec] A packet subblock manage has failed cpp-ucode LOG_STD_ACTION CPP_SBC-4-CPP_SBC_NULL_EXMEM 4-Warning Unexpected NULL shared-local EXMEM handle - ref_count [dec] The error will be corrected and pinhole programming will continue. asr1k-sbc LOG_STD_NO_ACTION CPP_WPAN_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION CPP_WPAN_PROXY-3-PROXY_IPC_PACKET_ALLOCATION_FAILED 3-Error [hec] Failed to allocate packet buffer for IPC cpp-ucode LOG_STD_ACTION CPP_WPAN_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error [hec] Failed to send IPC packet. cpp-ucode LOG_STD_ACTION CPP_WPAN_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION CPPBQS-3-MULTICOMMITS 3-Error Multiple outstanding [chars] commit events detected [dec] - - - CPPBQS-3-QMOVEFAIL 3-Error CPP [dec] schedule [chars] queue move failed [hex] - SEID=[hex] SID=%#X A QFP BQS schedule queue move operation failed. qfp-bqs-internal LOG_STD_SH_TECH_ACTION CPPBQS-3-QMOVEQOSDIS 3-Error QFP [dec] schedule [chars] queue move to [chars] unsupported QoS disabled QFP BQS schedule move to new output interface on different subdevice is unsupported. QoS for this schedule is disabled qfp-bqs-internal "Restore failed link or route so that schedule " "is moved back and QoS is restored. Or force the " "schedule to fail back to a link that is on " "the same subdevice the this schedule was " "originally on." CPPBQS-3-QMOVESTUCK 3-Error QFP [dec] schedule [chars] queue move operation is not progressing as expected - seq [dec] A QFP schedule queue move operation is not proceeding as expected and can lead to packet drops. The most likely cause of a queue move operation getting stuck is having a rate based queue that has packets enqueued on it that are not being serviced very frequently or being starved due to higher priority queues causing an oversubscription of the physical output interface. qfp-bqs-internal "No action is required if QMVOEDONE message" " is also displayed following QMOVESTUCK." " If a QMOVEDONE or QMOVEPROC message is not" " displayed following QMOVESTUCK then" " collect the data from the following show" " commands:" " show platform" " show platform hardware qfp bqs status" " show platform hardware qfp bqs qmove info" " show platform hardware qfp bqs qmove child" " show platform hardware qfp bqs qmove flush" "Report the problem to the Cisco TAC providing" " the data from the above show commands." CPPBQS-3-RATE_RATIO_OPTIMIZATION 3-Error QFP BQS detected invalid rate optimization nodes for [chars] QFP unable to optimize the rates due to missing optimization nodes qfp-bqs-internal "Enable 'platform qos optimize-rate-ratio' command " "before applying QOS." CPPBQS-3-REPARENTFAIL 3-Error QFP [dec] schedule [chars] reparent failed [hex] - SEID=%#X SID=[hex] A QFP BQS schedule reparent operation failed. qfp-bqs-internal LOG_STD_SH_TECH_ACTION CPPBQS-3-SRT_PERR_RESORT_FAIL 3-Error QFP [dec] unable to resort to correct parity error at SEID=%#X A QFP BQS SRT parity error occurred that was uncorrectable qfp-bqs-internal LOG_STD_NO_ACTION CPPBQS-4-MAXRATEPROFILELIMITEXCEEDED 4-Warning QFP [dec].[dec] Max Rate Profile limit [dec] exceeded at [dec]. Max number of Max Rate Profiles supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results. - "Reduce the number of unique shape rates in the configuration" CPPBQS-4-MINRATEPROFILELIMITEXCEEDED 4-Warning QFP [dec].[dec] Min Rate Profile limit [dec] exceeded at [dec]. Max number of Min Rate Profiles supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results. - "Reduce the number of unique bandwidth rates in the configuration" CPPBQS-4-QLIMITEXCEEDED 4-Warning QFP [dec].[dec] QoS Queue limit [dec] exceeded at [dec]. Max number of QoS queues supported on QFP has been exceeded. Configuration failure is possible causing unpredictable results. - "Reduce the size of the QoS configuration" CPPBQS-4-QMOVEDONE 4-Warning QFP [dec] schedule [chars] queue move done A QFP BQS schedule queue move operation was not proceeding in a timely manner and flagged as being stuck but has since completed. cpp-sw LOG_STD_SH_TECH_ACTION CPPBQS-4-QMOVEPROC 4-Warning QFP [dec] schedule [chars] queue move in progress seq [dec] A QFP BQS schedule queue move operation is not proceeding or is proceeding at a slow rate which can lead to packet drops. The most likely cause of a queue move operation getting stuck is having a rate based queue that has packets enqueued on it that are not being serviced very frequently or being starved due to higher priority queues causing an oversubscription of the physical output interface. qfp-bqs-internal "No action is required if QMVOEDONE message" " is also displayed following QMOVEPROC." " If QMOVEDONE message is not displayed or" " you continue to see QMOVEPROC messages" " displayed then collect the data from" " the following show commands:" " show platform" " show platform hardware qfp bqs status" " show platform hardware qfp bqs qmove info" " show platform hardware qfp bqs qmove child" " show platform hardware qfp bqs qmove flush" "Report the problem to the Cisco TAC providing" " the data from the above show commands." CPPBQS-4-SRTMEMLOW 4-Warning QFP [dec] HW [chars]:[chars] schedule resources depleted - [dec]%% available QFP BQS HW schedule resources have dropped below critical threshold. qfp-bqs-internal LOG_STD_REDUCE_ACTION CPPBQS-4-YODASRTMEMLOW 4-Warning QFP [dec].[dec] HW [chars]:[chars]:[chars] schedule resources depleted - [dec]%% available QFP BQS HW schedule resources have dropped below critical threshold. qfp-bqs-internal LOG_STD_REDUCE_ACTION CPPBQS-6-QLIMITOK 6-Information QFP [dec].[dec] QoS Queue limit [dec] was exceeded and is now within platform specifications at [dec]. Max number of QoS queues supported on QFP was exceeded. It is now within platform specifications - - CPPBQS-6-QMOVEQOSENA 6-Information QFP [dec] schedule [chars] queue move to [chars] QoS enabled QFP BQS schedule that was disabled due to having been moved to an output interface on different subdevice has now moved back to the original subdevice and QoS is now enabled again. - - CPPBQS-6-QMRTDUMP 6-Information QFP Queue Manager Real-Time trace dump - [chars] The QFP Queue Manager Real-Time trace data dumping to disk has either started or completed. - - CPPBQS-6-QMRTREPLAY 6-Information QFP Queue Manager Real-Time event replay [chars] - [chars] The QFP Queue Manager Real-Time event data replay from disk file status display - - CPPCDM-3-ERROR_NOTIFY 3-Error QFP [dec] thread [dec] encountered an error -Traceback= [chars] [chars] A QFP fault has occurred. cpp-ucode LOG_STD_NO_ACTION CPPDRV-2-HALT 2-Critical [chars][dec] Interrupt : [chars] Seq:%03d Halt bit set. A Serious CPP hardware error has occurred. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-ALLOC_NOTF 3-Error CPP[dec]: Failed to Allocate: [chars] A function failed to allocate data. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-CLEANUP_NOTF 3-Error Failed to Cleanup: [chars] A function failed to cleanup data. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-DESTROY_NOTF 3-Error Failed to destroy connection :[chars] A function failed to destroy a connection. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_ACQUIRE_LOCK 3-Error CPP[dec]: 0x[hec] Failed to acquire memory lock [chars] SW failed to acquire shared memory lock cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_ALLOCATE 3-Error CPP[dec]: 0x[hec] Failed to allocate [chars] - [chars] Failed to allocate data cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_ATTACH 3-Error CPP[dec]: 0x[hec] FAILED: to attach [chars] Device Failed to attach cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_CPP_SUBDEV_ACCESS 3-Error CPP[dec].[dec]: An access error has been reported. Error count [dec]. The system has reported an error while accessing a CPP subdevice cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_CPU_FEATURE 3-Error CPP[dec]: CPU lacks feature [chars]. Packet forwarding disabled. The currently installed CPU lacks a certain feature that is required by the forwarding engine. The QFP is operating with reduced functionality with packet forwarding disabled. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_CREATE 3-Error 0x[hec] Failed to create [chars] - [chars] Failed to create device cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_CREATE_ID 3-Error CPP[dec]: 0x[hec] Failed to create [chars] - [chars] Failed to create device cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_GET_DETAILS 3-Error CPP[dec]: 0x[hec] Failed to get [chars] details - [chars] Failed to get device details cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INIT 3-Error 0x[hec] Failed to initialize [chars] - [chars] Failed to init device cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INIT_ID 3-Error CPP[dec]: 0x[hec] Failed to initialize [chars] - [chars] Failed to init device cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INTERNAL 3-Error CPP[dec]: 0x[hec] Internal Error [chars] Internal coding error. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INTERRUPT_CLEAR 3-Error CPP[dec]: 0x[hec] Failed to clear [chars] interrupt Failed to clear an interrupt node cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INTERRUPT_HANDLER 3-Error CPP[dec]: 0x[hec] Failed to register [chars] interrupt handler - [chars] Failed to register interrupt handler cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INTERRUPT_INIT 3-Error CPP[dec]: 0x[hec] Failed to initialize [chars] interrupt - [chars] Failed to initialize an interrupt cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_INTERRUPT_OPEN 3-Error CPP[dec]: 0x[hec] Failed to access [chars] interrupt node - [chars] Failed to open an interrupt cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_MEM_CLEAR 3-Error CPP[dec]: 0x[hec] Failed to clear memory [chars] SW failed to clear memory location cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_MEM_SIZE 3-Error CPP[dec]: 0x[hec] Failed to acquire memory size [chars] SW failed to acquire the size of a block of memory cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_MEM_WRITE 3-Error CPP[dec]: 0x[hec] Failed to write to memory [chars] SW failed to write to a memory location cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_MIN_CPU 3-Error CPP[dec]: Insufficent number of CPUs detected = [dec] required = [dec] The current system lacks a sufficent number of CPUs or cores cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_PLAT_DB 3-Error CPP[dec]: 0x[hec] Platform failure accessing [chars] Platform DB query failed cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_RELEASE_LOCK 3-Error CPP[dec]: 0x[hec] Failed to release memory lock [chars] SW failed to release shared memory lock cpp-sw LOG_STD_NO_ACTION CPPDRV-3-FATAL_UNSUPPORT 3-Error CPP[dec]: 0x[hec] - unsupported CPP TYPE. CPP TYPE:[dec] Unsupported CPP TYPE cpp-sw LOG_STD_NO_ACTION CPPDRV-3-GUEST_CPU_FEATURE 3-Error CPP[dec]: Guest CPU lacks feature [chars]. The currently installed Guest CPU lacks a certain feature that is required by the forwarding engine but that feature is supported by the Host CPU. The QFP is operating with normal functionality using the host CPU feature but live migration to a host which lacks this feature will result in a crash. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-HOT 3-Error [chars][dec] Interrupt : [chars] Seq:%03d repeating interrupt has been disabled. A repeating hardware interrupt has been disabled. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-INIT_NOTF 3-Error Failed to initialize: [chars] A function failed to initialize. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-INIT_NOTF_ID 3-Error CPP[dec]: Failed to initialize: [chars] A function failed to initialize. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-LOCKDOWN 3-Error QFP[dec].[dec] CPP Driver LOCKDOWN encountered due to previous fatal error [chars]: [chars]. A fatal error has caused the driver to LOCKDOWN. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-LOCKDOWN_INITIATED 3-Error QFP[dec].[dec] CPP Driver LOCKDOWN being triggered due to fatal error. A fatal error has caused the process to initiate LOCKDOWN. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-SRT_PERR_FAILURE 3-Error [chars][dec] Failed to correct BQS SRT Parity error. Failed to correct a BQS SRT Parity error. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-TCAM_PERR 3-Error [chars][dec] TCAM Parity error TCAM device #[dec] at offset 0x%08X. A Parity error has occurred in a TCAM device. cpp-sw LOG_STD_NO_ACTION CPPDRV-3-TCAM_PERR_FAILURE 3-Error [chars][dec] Failed to correct TCAM Parity error. Parity error detection disabled. Failed to correct a TCAM Parity error and further detection has been disabled. cpp-sw LOG_STD_NO_ACTION CPPDRV-4-ADRSPC_LIMIT 4-Warning Address space limit [dec] KB reached mapping block [chars] size [dec] dynamically over limit space: [dec] KB The process indicated tried to map more of the Forwarding Engine's address space than was allocated for it. A slower access method will be used instead. This will lower the performance of some operations which require accesses to the Forwarding Engine cpp-sw LOG_STD_SH_TECH_ACTION CPPDRV-4-CORE_TABLE 4-Warning CPP[dec] specific core dump table '[chars]' not found using minimal fallback table '[chars]' instead The QFP configuration found on this board did not match any of the tables which define which data has to be collected if a fatal error is detected. Instead a minimal table is used which covers most of the QFP registers. The QFP is fully operational. cpp-sw LOG_STD_SH_TECH_ACTION CPPDRV-4-CPU_FEATURE 4-Warning CPP[dec]: CPU lacks feature [chars]. Performance may be sub-optimal. The currently installed CPU lacks a certain feature that improve performance of the forwarding engine. The QFP is fully operational but may operate at a reduced capacity. cpp-sw LOG_STD_NO_ACTION CPPDRV-4-FIXUP_OCCURRED 4-Warning Alignment fixup @ PC=%p #hits=[dec] fault addr: %p. A misalignment was handled by a fixup signal handler cpp-sw LOG_STD_NO_ACTION CPPDRV-4-FIXUP_OCCURRED_TRACEBACK 4-Warning Alignment fixup #hits=[dec] Traceback [chars] A misalignment was handled by a fixup signal handler cpp-sw LOG_STD_NO_ACTION CPPDRV-4-FUTURE_FATAL_CPU_FEATURE 4-Warning CPP[dec]: CPU lacks feature [chars] required in a future release. The currently installed CPU lacks a certain feature that will be required by the forwarding engine in a future release. Caution is advised before upgrading to a newer release to ensure the CPU has the minimum set of CPU features necessary to operate. cpp-sw LOG_STD_NO_ACTION CPPDRV-4-HW_REV_OLD 4-Warning Found HW revision [chars] using [chars] based on [chars]. No customer deployment. The specified board or chip showed an incorrect invalid or too old hardware revision. That hardware revision was possibly overridden cpp-sw LOG_STD_NO_ACTION CPPDRV-6-ACCTRC16B 6-Information Access CPP [dec] address 0x%08llX Blk/Off:[chars]/0x%08llX [chars] %3d bytes A CPP access was traced cpp-sw LOG_STD_NO_ACTION CPPDRV-6-ACCTRC8B 6-Information Access CPP [dec] address 0x%08llX Blk/Off:[chars]/0x%08llX [chars] %3d bytes A CPP access was traced cpp-sw LOG_STD_NO_ACTION CPPDRV-6-INTR 6-Information [chars][dec] Interrupt : [chars] A CPP hardware interrupt has occurred. cpp-sw LOG_STD_NO_ACTION CPPEXMEM-3-NOMEM 3-Error QFP: [dec] [chars] memory allocation of [dec] bytes by [chars] failed A request for QFP memory resource allocation has failed due to running out of memory. QFP memory is used by the datapath for packet forwarding. - "Display the memory allocation usage" " per feature to determine where most" " of the memory is being used. This can" " help identify where to adjust feature" " scaling. The following CLI will display" " the memory utilization: show platform" " hardware qfp act infrastructure exmem" " statistics user. If the system crashed" " prior to issuing this command you can" " retrieve the information from the binary" " trace log file for the process that " " generated this error message." CPPEXMEM-3-TOPUSER 3-Error QFP: [dec] Top User: [chars] [chars]: [dec] Type: [chars] A request for QFP memory resource allocation has failed due to running out of memory. The top consumer of exmem is provided with this message to possibly identify the source for running out of memory. QFP memory is used by the datapath for packet forwarding. - LOG_STD_NO_ACTION CPPEXMEM-4-LOWMEM 4-Warning CPP [dec] [chars] memory low - [dec] percent depleted A CPP memory resource has dropped below a critical level. - LOG_STD_NO_ACTION CPPEXMEM-5-MEM 5-Notice CPP [dec] [chars] memory recovered - [dec] percent depleted A CPP memory resource has recovered above the low threshold level. - LOG_STD_NO_ACTION CPPFW-2-L4_POLICY_ATTACH_FAIL 2-Critical ZBFW failed to attach policy [dec]:[chars] to zone-pair [dec]:[chars] : [chars] Error attaching policy to zone-pair. Configuration failed. Security policy not enforced for the zone-pair iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-2-L4_POLICY_EDIT_FAIL 2-Critical ZBFW failed to edit policy [dec]:[chars] for zone-pair [dec]:[chars] : [chars] Error editing policy. Configuration failed. New security policy not enforced for the zone-pair iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-4-CHUNK_CREATE_FAIL 4-Warning Failed to create chunk pool: [chars] : [chars] Could not create memory chunk pool. Configuration Failed iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-4-L4_PER_FLTR_STATS_TBL_ALLOC_FAIL 4-Warning Error [chars] failed to allocate L4 per filter stats tables to data plane: zone pair id: [dec]:[chars] policy id [dec]:[chars] : [chars] Could not alloc L4 per fltr stats table to data plane. Configuration Failed iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-4-L7_NBAR_TCAMID_MEM_ALLOC_FAIL 4-Warning Failed to create l7 nbar tcam entry zone pair: [chars] class [chars] : [chars] Could not allocate memory for l7 nbar cce tcam info. Configuration Failed iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-4-NO_CG 4-Warning [chars] Could not locate class group [chars] zone_pair id [dec]:[chars] cg id: [dec] Could not locate class group policy inforamtion. Configuration Failed iosxe-zbfw LOG_STD_NO_ACTION CPPFW-4-NO_CLASS_CG 4-Warning [chars]: Could not locate class [chars] zone_pair id [dec]:[chars] policy: [dec]:[chars] class id: [dec] Could not Locate class inforamtion. Configuration Failed iosxe-zbfw LOG_STD_NO_ACTION CPPFW-4-NO_FM_STAT_MAP_CG 4-Warning [chars]: Could not locate fm stat map table: [chars]. zone_pair id: [dec]:[chars] cg: [dec]:[chars] Could not Locate CPP FM_STAT mapping table. Configuration Failed iosxe-zbfw LOG_STD_NO_ACTION CPPFW-4-NO_MEM_ZP_CG_ARY_CG 4-Warning [chars]: [chars]: Could not allocate [chars] [dec] bytes x [dec] entries for [dec] bytes of memory zone pair: [dec]:[chars] policy: [dec]:[chars] Could not allocate an array of memory of the given size and entries. Configuation Failed iosxe-zbfw "Configureation is too large for platform." " Attempt to reduce" " size of firewall policy stats etc. " " or disable other features" CPPFW-4-WRITE_HW_L7_NBAR_TCAMID_FAIL 4-Warning Failed to write l7 nbar tcamid [chars] to data plane: zone pair: [chars] class [chars] : [chars] Could not write l7 nbar cce tcam info to data plane. Configuration Failed iosxe-zbfw LOG_STD_REDUCE_ACTION CPPFW-4-WRITE_HW_MEM_FAIL_CG 4-Warning [chars]: [chars]: [chars]: zone_pair id: [dec]:[chars] policy: [dec]:[chars] class: [chars] Could not write data to data plane. Configuration Failed iosxe-zbfw LOG_STD_NO_ACTION CPPFW-4-ZBFW_GENERIC_FAIL 4-Warning zbfw : [chars] Failure in zbfw iosxe-zbfw LOG_STD_NO_ACTION CPPFW-4-ZONE_CREATE_DEFER_FAIL 4-Warning Could not create defer zone entry for zone [chars] id [dec] parameter map id [dec] error [dec]:[chars] Could not allocate memory for for deferred creation of indicated zone. Configuration Failed iosxe-zbfw "Configureation is too large for platform." " Attempt to reduce" " size of firewall policy stats etc. " " or disable other features" CPPFW-4-ZONE_CREATE_FAIL 4-Warning Could not create zone [chars] id [dec] error [dec]:[chars] Could not allocate memory for indicated zone. Configuration Failed iosxe-zbfw "Configureation is too large for platform." " Attempt to reduce" " size of firewall policy stats etc. " " or disable other features" CPPFW-4-ZONE_MODIFY_FAIL 4-Warning Could not create zone [chars] id [dec] parameter map id [dec] error [dec]:[chars] Modification of zone failed. Configuration in indeterminate state. iosxe-zbfw "Configureation is too large for platform." " Attempt to reduce" " size of firewall policy stats etc. " " or disable other features" CPPHA-3-BULKSYNC 3-Error bulk sync processing failed to complete - - - CPPHA-3-CDMDONE 3-Error CPP [dec] microcode crashdump creation completed. The CDM has completed generating microcode crashdump. - LOG_STD_SH_TECH_ACTION CPPHA-3-CHUNKALLOC 3-Error Chunk allocation failed [dec] - - - CPPHA-3-CHUNKCREATE 3-Error Chunk Create failed [dec] - - - CPPHA-3-CHUNKFREE 3-Error Chunk free failed [dec] The CPP bulk synchronization processing failed on the standby. - LOG_STD_SH_TECH_ACTION CPPHA-3-EXMEMALLOC 3-Error exmem allocation failed - - - CPPHA-3-EXMEMBIND 3-Error bind to exmem failed to complete - - - CPPHA-3-FAILURE 3-Error CPP [dec] failure [chars] detected A CPP failure has been detected. cpp-ucode LOG_STD_SH_TECH_ACTION CPPHA-3-FAULT 3-Error CPP:[dec].[dec] desc:[chars] det:[chars] class:[chars] sev:[chars] id:[dec] cppstate:[chars] res:[chars] flags:0x[hec] cdmflags:0x[hec] A CPP fault has occurred. cpp-ucode LOG_STD_NO_ACTION CPPHA-3-FAULTCRASH 3-Error CPP [dec].[dec] unresolved fault detected initiating crash dump. A unresolved fault detected initiating crash dump. - LOG_STD_SH_TECH_ACTION CPPHA-3-FAULTRATE 3-Error CPP:[dec].[dec] desc:[chars] det:[chars] class:[chars] sev:[chars] id:[dec] cppstate:[chars] res:[chars] flags:0x[hec] cdmflags:0x[hec] A CPP fault has occurred. cpp-ucode LOG_STD_NO_ACTION CPPHA-3-FDBQUERY 3-Error [chars] FDB query failed [dec] [chars] - - - CPPHA-3-INITFAIL 3-Error CPP [dec] initialization failed - [chars] [hex] A CPP initialization failed. cpp-sw LOG_STD_SH_TECH_ACTION CPPHA-3-NOCDM 3-Error CPP [dec] CDM not running. The CDM process is not running. - LOG_STD_SH_TECH_ACTION CPPHA-6-SYSINIT 6-Information CPP HA system [chars]. CPP system initialization state. - LOG_STD_NO_ACTION CPPHA-7-READY 7-Debug CPP [dec] loading and initialization complete A CPP has been successfully loaded and initialized\n\ ready to be configured for forwarding packets. - LOG_STD_NO_ACTION CPPHA-7-START 7-Debug CPP [dec] [chars] A CPP is being started. - LOG_STD_NO_ACTION CPPHA-7-SYSREADY 7-Debug CPP client process [chars] [dec] of [dec] ready. A CPP Client process has started and registered with\n\ CPP HA Server. - LOG_STD_NO_ACTION CPPOSLIB-3-CLEAN_NOTIFY 3-Error Failed to cleanup: [chars] A function failed to cleanup data. cpp-sw LOG_STD_NO_ACTION CPPOSLIB-3-ERROR_NOTIFY 3-Error [chars] encountered an error Print error message to console cpp-sw LOG_STD_NO_ACTION CPPOSLIB-3-GET_NOTIFY 3-Error Failed to get data: [chars] A function failed to get data. cpp-sw LOG_STD_NO_ACTION CPPOSLIB-3-INIT_NOTIFY 3-Error Failed to initialize: [chars] A function failed to initialize. cpp-sw LOG_STD_NO_ACTION CPPOSLIB-3-REGISTER_NOTIFY 3-Error Failed to register: [chars] A function failed to register. cpp-sw LOG_STD_NO_ACTION CPPUI-3-ERROR_NOTIFY 3-Error [chars] An UI fault has occurred. - LOG_STD_ACTION CPU_NET-0-QUEUE_STUCK 0-Emergency The interface between the CPU and the switch has\n become stuck. The switch must now reset to clear this condition\n. Retrieval queue [dec].\n The CPU can no longer communicate with the network. - "Reload the system." CPU_REDUN -2-INITSYS 2-Critical [chars] A software error occurred during initialization of the CPU redundancy subsystem - "Check for sufficient processor memory." LOG_STD_ACTION CPU_REDUN-3-4MSEC_DISABLED 3-Error [chars] [dec] The 4msec timer interrupt was shut off for an extended period while the hardware watchdog was enabled. - LOG_STD_ACTION CPU_REDUN-3-BKPLN_IDPROM_ACCESS 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor can not access its backplane IDPROM. - LOG_STD_ACTION CPU_REDUN-3-CAPAB_SIZE 3-Error Mismatch in [chars]. Active=[dec] Standby=[dec]. Standby CPU is reporting lower Capabilities than the Active CPU. See message text for type of limitation. - "Check for sufficient Standby CPU capabilities." LOG_STD_ACTION CPU_REDUN-3-CAPAB_VERS 3-Error Mismatch in [chars]. Active=[dec].[dec] Standby=[dec].[dec]. Standby CPU is reporting lower versions than the Active CPU. See message text for type of limitation. - "Check Standby CPU version numbers." LOG_STD_ACTION CPU_REDUN-3-CAPABILITIES 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the capabilities reported by the standby processor are less than the active processor. The processors are conditionally redundant which means that a switchover could result in a partial loss of system control. - LOG_STD_ACTION CPU_REDUN-3-DRIVER_MISSING 3-Error Missing [chars] driver support on Standby. Active=[dec].[dec] Standby CPU is missing support for one of the drivers available on the Active CPU. The corresponding linecard will go down in the event of a switchover. - "May require a software upgrade on the Standby CPU. " LOG_STD_ACTION CPU_REDUN-3-DRIVER_VERSIONS 3-Error Mismatch in [chars] driver versions. Active=[dec].[dec] Standby=[dec].[dec]. Standby CPU is reporting lower versions than the Active CPU. See message text for type of limitation. May result in a loss of connections. - "May require a software upgrade on the Standby CPU. " LOG_STD_ACTION CPU_REDUN-3-EHSA_SVCS 3-Error [chars] [chars] An error occurred that affects CPU Redundancy services. The details about what was attempted and what went wrong will be printed. - LOG_STD_ACTION CPU_REDUN-3-GT_STATUS_REG 3-Error Parity Error on PCI Bus from PCI Device A Parity error on PCI bus has occurred while validating the GT64120 PCI device hanging off the PCI bus ons155xx-cpu "Check whether it is a GT64120 device.\n" LOG_STD_ACTION CPU_REDUN-3-INCONSISTENT_STATES 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor redundancy state is either not consistent with the peer state or the software state is not consistent with the hardware state. - LOG_STD_ACTION CPU_REDUN-3-INIT_ERROR 3-Error [chars] [dec] [dec] A subsystem initialization error occurred. - LOG_STD_NO_ACTION CPU_REDUN-3-INTRPT_HOG 3-Error [chars] [dec] sec [chars] = [hec] The CPU redundancy process didn't run for a long time because an interrupt routine ran too long. - LOG_STD_ACTION CPU_REDUN-3-INVALID_CPU_STATES 3-Error Detected invalid redundancy states local = [chars] peer = [chars] Detected an invalid combination of redundant states - LOG_STD_NO_ACTION CPU_REDUN-3-INVALID_MSG 3-Error Incorrectly formatted message 0x[hec] 0x[hec] received by [chars] Inconsistent message data was received from the peer CPU possibly due to an incompatible image version. - LOG_STD_ACTION CPU_REDUN-3-LOCK_ERR 3-Error Can't get Global Lock Peer CPU won't relinquish the arbitration lock. - "Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION CPU_REDUN-3-MULTI_CARD_ACCESS 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor has failed the linecard access test for multiple linecards. - LOG_STD_ACTION CPU_REDUN-3-PCI_STATUS_REG 3-Error Status error in PCI device [dec] A PCI Status registry error in PCI device has been detected when validating the PCI device hanging off the PCI bus ons155xx-cpu "Check whether it is a valid PCI device Manhattan." "\n" LOG_STD_ACTION CPU_REDUN-3-PCI_TEST 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor has failed the online diagnostic internal PCI bus test. - LOG_STD_ACTION CPU_REDUN-3-PCI_VENDORID_MISMATCH 3-Error Error/Mismatch in reading Vendor ID for PCI device [dec] The PCI Vendor ID error/mismatch has been detected when validating the PCI device hanging off the PCI bus ons155xx-cpu "Check the vendor ID of the PCI device attached it should of a macro value like: CLPD6729_VENDOR_ID" "\n" LOG_STD_ACTION CPU_REDUN-3-PCMCIA_TEST 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor has failed the online diagnostic internal PCMCIA slot test. - LOG_STD_ACTION CPU_REDUN-3-PEER_COMM 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the peer processor is present but not responding or sending keepalives. - LOG_STD_ACTION CPU_REDUN-3-PEER_MISSING 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the peer processor is either missing or can not be detected. The active processor currently is not being protected. - LOG_STD_ACTION CPU_REDUN-3-PEER_SEVERITY_ERR 3-Error Invalid peer CPU severity [dec] current peer register=0x[hec] Peer CPU is reporting an invalid severity value. - "Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION CPU_REDUN-3-PEER_SRC_REGS 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the active processor is detecting bad parity on the active/standby bits read from the standby processor. - LOG_STD_ACTION CPU_REDUN-3-PEER_STATE_ERR 3-Error Invalid peer CPU state [chars] current peer register=0x[hec] Peer CPU is reporting an invalid redundancy state. - "Check that both the local and peer CPUs " "are fully seated in the backplane. Check " "the health of the Peer CPU." LOG_STD_ACTION CPU_REDUN-3-RCSF_FAIL 3-Error Attempt to sync running config to standby failed Unable to send Running Config file to Standby CPU - LOG_STD_NO_ACTION CPU_REDUN-3-READBACK_ERR 3-Error Can't change my state. desired state [chars] read-back [chars] Local CPU can't set its redundancy state to the desired calculated value - "Check health of local CPU." LOG_STD_ACTION CPU_REDUN-3-SLOT_IDPROM_MISMATCH 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the slot ID read from the backplane IDPROM does not match the slot ID read from the SRC. - LOG_STD_ACTION CPU_REDUN-3-SRC_TEST 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] The alarm appears when the processor has failed the online diagnostic internal SRC test. - LOG_STD_ACTION CPU_REDUN-3-STARTUP_SYNC_FAIL 3-Error Attempt to sync [chars] config to standby failed Unable to send Startup or Private Config file to Standby CPU - LOG_STD_NO_ACTION CPU_REDUN-3-SUBSYS_COMPAT 3-Error [chars] [chars] software subsystem. Active=[dec] Standby=[dec]. Standby CPU software subsystem is older or missing. See message text for software subsystem type. May result in feature losses in the event of a switchover. - "May require a software upgrade on the Standby CPU. " LOG_STD_ACTION CPU_REDUN-3-SW_STATE_MISMATCH 3-Error Software state [chars] doesn't reflect local hardware [chars] Software state is not following the underlying hardware redundancy state - LOG_STD_ACTION CPU_REDUN-3-UART_FAILURE 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] This alarm appears when the processor can't transmit characters on the console UART. It indicates a probable equipment failure - "If the symptom persists following a reload " "remove and replace the processor module." CPU_REDUN-3-UNKNOWN_COMMON 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] If the alarm appears when this is asserted for a standby processor with a different software image it indicates an alarm condition on the peer that the active processor can not decode. If this is asserted for the active processor it indicates a software error condition. - LOG_STD_ACTION CPU_REDUN-3-UNKNOWN_MSG 3-Error Unknown message type 0x[hec] received by [chars] An unknown message type was received from the peer CPU possibly due to an incompatible image version. - LOG_STD_ACTION CPU_REDUN-3-UNKNOWN_PLAT 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] If the alarm appears when this is asserted for a standby processor with a different software image it indicates an alarm condition on the peer that the active processor can not decode. If this is asserted for the active processor it indicates a software error condition. - LOG_STD_ACTION CPU_REDUN-4-REPROGRAM_ACTIVE_CPU 4-Warning Active CPU FPGA has been \nreprogrammed. Please remove and re-insert the CPU in slot [dec] or\npower-cycle the box for the new FPGA to take effect. Active CPU FPGA has been reprogrammed. This CPU is now running with old FPGA and it needs to be hot-swapped or the system needs to be power-cycled for the new FPGA to take effect. - LOG_STD_NO_ACTION CPU_REDUN-4-STARTUP_CONFIG_MISSING 4-Warning Non-volatile configuration memory is not present The startup-config is missing. This may be due to either a manual user erase command or an interrupted write to the startup-config. - "Do a copy running-config startup-config to save" "current system configuration. " LOG_STD_RECUR_ACTION CPU_REDUN-4-UNPROTECTED 4-Warning [chars] [dec] [chars] System is running for an extended period in an unprotected mode even though a peer CPU is present - "Check the health of the Peer CPU. Configure as " "maintenance mode to intentionally suppress error " "messages." LOG_STD_ACTION CPU_REDUN-5-BASIC_CAPABILITY 5-Notice Peer CPU hardware and software is fully compatible. Standby CPU H/W drivers and software subsystems have matching versions and capabilities. - LOG_STD_NO_ACTION CPU_REDUN-5-EHSA_SVCS_RESP 5-Notice Sending [chars] = [dec] Normal response for CPU EHSA Redundancy services. The details about what was sent will be printed. - LOG_STD_NO_ACTION CPU_REDUN-5-FORCE_CLOSE 5-Notice Forcibly closing fd: [dec] name:[chars] A file activity timeout occurred on the slave. - LOG_STD_NO_ACTION CPU_REDUN-5-NEGOTIATED_SWITCHOVER 5-Notice [chars] [dec] Reloading due to a negotiated switchover. - LOG_STD_NO_ACTION CPU_REDUN-5-PEER_EXITED_IOS 5-Notice Peer CPU has exited IOS Peer CPU has exited IOS. - LOG_STD_NO_ACTION CPU_REDUN-5-PEER_REMOVED 5-Notice Peer CPU has been removed from the chassis Peer CPU has been removed from the chassis. - LOG_STD_NO_ACTION CPU_REDUN-5-RCSF_SYNCED 5-Notice Running config successfully synced to standby Running Config file was sent to the Standby CPU - LOG_STD_NO_ACTION CPU_REDUN-5-RELOAD_COMM_DOWN 5-Notice [chars] Reloading standby since Active CPU shows loss of comm. - LOG_STD_NO_ACTION CPU_REDUN-5-STARTUP_CONFIG_SYNCED 5-Notice Startup config successfully synced to standby Startup Config file was sent to the Standby CPU - LOG_STD_NO_ACTION CPU_REDUN-5-STATE_MISMATCH_RELOAD 5-Notice [chars] Reloading due to a hardware software state mismatch. - LOG_STD_NO_ACTION CPU_REDUN-5-STATUS_CHG 5-Notice [chars] sev [dec] peer is [chars] sev [dec] A CPU hardware redundancy status change occurred. - LOG_STD_NO_ACTION CPU_REDUN-5-SWITCHOVER 5-Notice Switchover occurred. Reason: [chars] A CPU switchover took place. The reported reason is listed in the error message text. - LOG_STD_NO_ACTION CPU_REDUN-5-UNSUPPORTED_MSG 5-Notice Msgtype [chars] sent by [chars] unsupported by peer. Peer responded that it didn't recognize a message sent by this CPU possibly due to a different image version. - "May require a software upgrade on the Standby CPU. " LOG_STD_ACTION CPU_REDUN-6-BOOTED_AS_ACTIVE 6-Information After returning to ROM by [chars] Informational message notifying about a system startup with no switchover. - LOG_STD_NO_ACTION CPU_REDUN-6-EHSA_SVCS_EVENT 6-Information [chars] [chars] A significant EHSA Redundancy services event occurred. The details will be printed. - LOG_STD_NO_ACTION CPU_REDUN-6-RUNNING_CONFIG_CHG 6-Information Running config on this CPU has possibly changed Informational message to notify of possible changes to the running-config file - LOG_STD_NO_ACTION CPU_REDUN-6-STARTUP_CONFIG_CHG 6-Information Startup config on this CPU has possibly changed Informational message to notify of possible changes to the startup-config file - LOG_STD_NO_ACTION CR10K_CLNT-3-CR10K_ASSERT_FAILED 3-Error Assert failed at line [dec] from func [chars] in file [chars] Detect assert failure in global level cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-CR10K_ASSERT_FAILED 3-Error Assert failed at line [dec] from func [chars] in file [chars] Detect assert failure in global level cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-CR10K_CLNT_ASSERT_FAILED 3-Error Assert failed at line [dec] from func [chars] in file [chars] for client [dec] Detect assert failure in client level cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-CR10K_CLNT_ASSERT_FAILED 3-Error Assert failed at line [dec] from func [chars] in file [chars] for client [dec] Detect assert failure in client level cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-IPCTXERR 3-Error IPC send failure: client=[dec] entity=[dec] ses=[dec]/[dec] msg=[dec] err=[chars] IPC send failure. cmts-platform LOG_STD_ACTION CR10K_CLNT-3-IPCTXERR 3-Error IPC send failure: client=[dec] entity=[dec] ses=[dec]/[dec] msg=[dec] err=[chars] IPC send failure. cmts-platform LOG_STD_ACTION CR10K_CLNT-3-MTU_UNAVAILABLE 3-Error cr10k client ses is down err:[dec] Application code is trying to get negotiated mtu before issu negotiation is finished. err:1 means issu nego has not finished. err:2 means issu nego has not started.The traceback decode usually can pinpoint which routine is trying toget mtu too early. In most cases it is a msg send routine that triesto get the msg mtu in order to allocate a right size msg buffer. If the msg is not critical or will be resent upon send failure then the fix is to call cr10k_clnt_get_ses_up_for_apps before get mtu cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-MTU_UNAVAILABLE 3-Error cr10k client ses is down err:[dec] Application code is trying to get negotiated mtu before issu negotiation is finished. err:1 means issu nego has not finished. err:2 means issu nego has not started.The traceback decode usually can pinpoint which routine is trying toget mtu too early. In most cases it is a msg send routine that triesto get the msg mtu in order to allocate a right size msg buffer. If the msg is not critical or will be resent upon send failure then the fix is to call cr10k_clnt_get_ses_up_for_apps before get mtu cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-TIMEOUT 3-Error Timeout waiting for [chars] slot [dec]/[dec] Timeout while waiting on the specified event. cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_CLNT-3-TIMEOUT 3-Error Timeout waiting for [chars] slot [dec]/[dec] Timeout while waiting on the specified event. cmts-platform "Copy the error and send it to TAC.""TAC team can contact cable team to check why this error occurs" CR10K_DIAG-3-LLQDROP 3-Error LLQ Drops on [chars] new_drops:[dec] total_drops:[dec] The health monitoring code has detected drops on the low latency queue of the specified interface. This is not expected behavior. The interface should be monitored to determine if drops continue to increase. platform-cmts LOG_STD_ACTION CR10K_DIAG-3-MEMLEAK 3-Error MemLeak Monitor: [chars] [chars] The health monitoring code has detected potential memory leaks by the local IOS sub-system. This is not an expected behavior. The sub-system should be monitored to detect if real memory leaks continue to happen. platform-cmts LOG_STD_ACTION CR10K_DIAG-5- DIAG_LOOP_ETSEC 5-Notice eTSEC loopback failure [chars] A loopback between eTSEC1 and eTSEC2 failed. ubr10k-sw "Monitor failed LC for excessive failures." CR10K_DIAG-5- DIAG_LOOP_MG 5-Notice US PHY [dec] loopback failure [chars] [dec] Failed to loopback frame from CPU -> PHY -> JIB3 US -> CPU ubr10k-sw "Monitor failed LC for excessive failures." CR10K_DIAG-5- DIAG_LOOP_RXERR 5-Notice US PHY [dec] loopback discrepency detected frames tx [dec] rx [dec] err [hec] Failed to loopback one or more frames ubr10k-sw "Monitor failed LC for excessive failures." CR10K_DIAG-5- DIAG_LOOP_SEQ 5-Notice US PHY [dec] loopback failed unexpected seq [dec] exp [dec] Failed to loopback one or more frames ubr10k-sw "Monitor failed LC for excessive failures." CR10K_DIAG-5-PXFOVERSUB 5-Notice PXF utilization is [dec]%% system is close to be overloaded. The health monitoring code has detected the system is close to be oversubscribed. platform-cmts LOG_STD_ACTION CR10K_DIAG-5-RU_OLDBUFF_HOLD 5-Notice IO-Buff-Hoard Monitor: [chars] The health monitoring code has detected potential memory leaks by the local IOS sub-system. This is not an expected behavior. The sub-system should be monitored to detect if real memory leaks continue to happen. platform-cmts LOG_STD_ACTION CR10KBH-1-INITFAIL 1-Alert [chars] initialization failure Backhaul Ethernet hardware initialization failed ubr10k-sw LOG_STD_ACTION CR10KBH-3-B2B_LINKDOWN 3-Error [chars] B2B port [dec] changed state to down Link state changed to down for B2B interface ubr10k-sw "Check the sfp+ and wire status for B2B interface" CR10KBH-3-B2B_SFPP_MISSING 3-Error [chars] B2B port [dec] SFP+ missing TenGigabit Ethernet SFP+ was removed from the B2B interface ubr10k-sw "Insert a TenGigabit ethernet SFP+ into the B2B interface" CR10KBH-3-INVALID_DATA_INSTANCE 3-Error interface type [chars] slot [dec] subunit [dec] vc [dec] : [chars] Data required to support the interface is not available. ubr10k-sw LOG_STD_SH_TECH_ACTION CR10KBH-3-MAXADDR 3-Error [chars] total addresses greater than [chars] The number of addresses in the address filter is too large ubr10k-sw LOG_STD_ACTION CR10KBH-3-RADIAN_VLANTCAM_EXCEEDED 3-Error [chars] vlanid [dec] Radian VLAN TCAM table full Radian has a maximum of 4K vlan tcam entries ubr10k-sw LOG_STD_SH_TECH_ACTION CR10KBH-3-SFPP_BAD_HW 3-Error Interface [chars] TenGigabit Ethernet module SFP+ has bad HW TenGigabit Ethernet SFP+ could not be read CRC error or tx fault ubr10k-sw "Insert a new TenGigabit Ethernet SFP+ into the Backhaul interface" CR10KBH-3-SFPP_MISSING 3-Error Interface [chars] TenGigabit ethernet module SFP+ missing TenGigabit Ethernet SFP+ was removed from the Backhaul interface ubr10k-sw "Insert a TenGigabit ethernet SFP+ into the Backhaul interface" CR10KBH-3-SFPP_NON_TENGIGE 3-Error Interface [chars] Inserted module not TenGigabit ethernet module SFP+ Non TenGigabit Ethernet SFP+ was inserted into the Backhaul interface ubr10k-sw "Insert a TenGigabit ethernet SFP+ into the Backhaul interface" CR10KBH-3-SFPP_SECURITY_FAIL 3-Error Interface [chars] TenGigabit Ethernet module SFP+ is not CISCO approved TenGigabit Ethernet SFP+ has failed cisco-EEPROM security check ubr10k-sw "Insert a approved vendor SFP+ into the Backhaul interface" CR10KBH-3-SFPP_SPURIOUS 3-Error Interface [chars] TenGigabit Ethernet module SFP+ is a duplicate spurious TenGigabit Ethernet SFP+ has a vendor & serial number duplicate of another ubr10k-sw "Insert a approved vendor SFP+ into the Backhaul interface" CR10KBH-3-WIRING_ERR 3-Error Wrong wiring detected at [chars] interconnect portportnum: [dec] please This error message will be printed out when local interconnect port link status mismatches with remote interconnect port link status. We should use cable fiber to connect the corresponding interconnect ports between active and standby. When the error msg is printed out please check: 1 if ubr10k-sw LOG_STD_SH_TECH_ACTION CR10KBH-6-B2B_LINKUP 6-Information [chars] B2B port [dec] changed state to up Link state changed to up for B2B interface ubr10k-sw LOG_STD_NO_ACTION CR10KBH-6-B2B_SFPP_OK 6-Information [chars] B2B port [dec] SFP+ inserted TenGigabit Ethernet SFP+ was inserted into the B2B interface ubr10k-sw LOG_STD_NO_ACTION CR10KBH-6-RADIAN_MACACCT_FULL 6-Information MAC accounting entries full for Radian in slot [chars] Radian has a maximum of 256 ingress and 256 egress MAC accounting entries ubr10k-sw LOG_STD_SH_TECH_ACTION CR10KBH-6-SFPP_OK 6-Information Interface [chars] 10GBASE-[chars] TenGigabit ethernet module SFP+ inserted TenGigabit Ethernet SFP+ was inserted into the Backhaul interface ubr10k-sw LOG_STD_NO_ACTION CRASH_DUMP-3-FILE_OP 3-Error FILE operation [chars] failed CRASH DUMP May not be successfull The File operation for dumping DSP crash details failed The error message could be a software issue or due to not enough disk space. - LOG_STD_NO_ACTION CRASH_DUMP-6-ABORT 6-Information CRASH DUMP aborted for device [dec] Crash dump aborted. Crash Dump may not be successfull - LOG_STD_NO_ACTION CRASH_DUMP-6-TIMEOUT 6-Information CRASH DUMP may not be successfull for the device [dec] Crash dump process timed out waiting for diaganostic messages - LOG_STD_NO_ACTION CRB_EVENT-3-CRB_RT_ERROR 3-Error CRB Runtime Exception: [chars] CRB Runtime Exception - LOG_STD_ACTION CRIMSON-3-DATABASE_MEMLEAK 3-Error Database memory leak detected in [chars] database [chars]/[chars]/[chars] size: %llu byte callsite: %016llX A memory leak has been detected in the database memory. The leaked object is identified by name crimson LOG_STD_ACTION CRIMSON-3-INITFAIL 3-Error Initialization of the IOS operational database facility failed [chars]. - - - CRIMSON-3-INITFAIL_OPER_FLUSH 3-Error Initialization of the IOS operational database flush facility failed. An unexpected condition has occurred which resulted in the IOS operational database flush facililty failing to start. External agents will not be able to access the contents of the IOS operational database. crimson LOG_STD_ACTION CRIMSON-3-INITFAIL_OPER_REDO 3-Error Initialization of the IOS operational database redo facility failed. An unexpected condition has occurred which resulted in the IOS operational database redo facililty failing to start. This is a serious problem and means that the IOS operation database facility will not be functional. crimson LOG_STD_ACTION CRIMSON-3-IOS_CONFIG_DB_GARBAGE_COLLECTION_START_FAIL 3-Error Unable to start the garbage collection process for the IOS config database The IOS configuration database garbage collection has failed to start. Without a garbage collection process stale objects will not be cleaned up. crimson LOG_STD_ACTION CRIMSON-3-IOS_CONFIG_DB_VALIDATION_FAIL 3-Error Data validation of the IOS configuration database failed [chars]. - - - CRIMSON-3-NESTED_LOCK 3-Error Database already locked by [chars]. An unexpected condition has occurred wherein the already locked IOS operational database was requested to be locked again. This problem means that external entities may not receive updates when operational data changes. crimson LOG_STD_ACTION CRIMSON-3-NGIOS_CONFIG_DB_GARBAGE_COLLECTION_START_FAIL 3-Error Unable to start the garbage collection process for the NGIOS config database The NGIOS configuration database garbage collection has failed to start. Without a garbage collection process stale objects will not be cleaned up. crimson LOG_STD_ACTION CRIMSON-3-UPDATE_FAIL 3-Error Processing of a IOS operational database update failed [chars]. - - - CRPGC-0-REFERENCE_STUBBED 0-Emergency stubbed [chars] is referenced - - "" CRYPTO_DEV_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical QFP Crypto device Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP Crypto device Proxy initialization detected that the IPC interface initialization failed. QFP Crypto device proxy will not be functional while this condition exists. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_DEV_PROXY-2-PROXY_REG_NULL_MSG_HNDLR 2-Critical QFP Crypto device Proxy registered invalid message handlers source: [chars]. Cisco internal software error. QFP Crypto device Proxy registered with invalid message handler. QFP Crypto device Proxy will not be functional while this condition exists. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_DEV_PROXY-3-PROXY_BAD_MSG 3-Error QFP Crypto device Proxy received bad length message type [dec] Cisco internal software error. QFP Crypto device Proxy received a corrupted message from control plane. This message will be ignored. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_DEV_PROXY-3-PROXY_INV_MSG 3-Error QFP Crypto device Proxy received invalid message type [dec] Cisco internal software error. QFP Crypto device Proxy received an invalid message from control plane. This message will be ignored. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_DEV_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error QFP Crypto device Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. QFP Crypto device Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_DEV_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error QFP Crypto device Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. QFP Crypto device Proxy message processing detected a message sent failure. The message is lost as the result of this condition. qfp-ipsec keyword:none LOG_STD_ACTION CRYPTO_ENGINE-0-AUDITFAIL 0-Emergency Encryption audit check found the wrong level of encryption in this image The audit check verifying encryption entitlement within the IOS image either found encryption in a non-encryption image or the wrong strength within an IOS image containing encryption. Use of the encryption may violate U.S. Export Laws and Regulations. - "Contact Cisco to obtain a replacement IOS image." CRYPTO_ENGINE-0-AUDITFAIL 0-Emergency Encryption audit check found the wrong level of encryption in this image The audit check verifying encryption entitlement within the IOS image either found encryption in a non-encryption image or the wrong strength within an IOS image containing encryption. Use of the encryption may violate U.S. Export Laws and Regulations. - "Contact Cisco to obtain a replacement IOS image." CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL 3-Error Cisco PSB security compliance violation is detected. Use of [chars] by [chars] is denied A security compliance violation has been detected. An attempt to use cryptography [chars] that is restricted - "Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk" CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL 3-Error Cisco PSB security compliance violation is detected. Use of [chars] by [chars] is denied A security compliance violation has been detected. An attempt to use cryptography [chars] that is restricted - "Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk" CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL_RSA 3-Error Cisco PSB security compliance violation is detected. Use of weak [dec] bit key is denied A security compliance violation has been detected. An attempt to use RSA cryptography with weak keys that is restricted by Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been denied. - "Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk" CRYPTO_ENGINE-3-CSDL_COMPLIANCE_FAIL_RSA 3-Error Cisco PSB security compliance violation is detected. Use of weak [dec] bit key is denied A security compliance violation has been detected. An attempt to use RSA cryptography with weak keys that is restricted by Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been denied. - "Use Cisco PSB approved cryptographic methods" "or remove the compliance profile that is active at your own risk" CRYPTO_ENGINE-3-FIPS_COMPLIANCE_FAIL 3-Error FIPS security compliance violation is detected. Use of [chars] by [chars] is denied A FIPS security compliance violation has been detected. The cryptography used is considered weak and violates the requiremnet set by FIPS - "Use FIPS approved cryptographic methods" "or disable FIPS mode and reload device" CRYPTO_ENGINE-3-FIPS_COMPLIANCE_FAIL 3-Error FIPS security compliance violation is detected. Use of [chars] by [chars] is denied A FIPS security compliance violation has been detected. The cryptography used is considered weak and violates the requiremnet set by FIPS - "Use FIPS approved cryptographic methods" "or disable FIPS mode and reload device" CRYPTO_ENGINE-4-AUDITWARN 4-Warning Encryption audit check could not be performed The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration. - "Manually verify that this IOS image is entitled to contain " "encryption." CRYPTO_ENGINE-4-AUDITWARN 4-Warning Encryption audit check could not be performed The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration. - "Manually verify that this IOS image is entitled to contain " "encryption." CRYPTO_ENGINE-4-CSDL_COMPLIANCE_DISABLED 4-Warning Cisco PSB security compliance has been disabled Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been disabled. - "Proceed with caution since weak cryptography will be allowed" CRYPTO_ENGINE-4-CSDL_COMPLIANCE_DISABLED 4-Warning Cisco PSB security compliance has been disabled Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB has been disabled. - "Proceed with caution since weak cryptography will be allowed" CRYPTO_ENGINE-4-CSDL_COMPLIANCE_RSA_WEAK_KEYS 4-Warning RSA keypair [chars] is in violation of Cisco security compliance guidelines and will be rejected by future releases. An attempt to use RSA cryptography with weak keys has been detected. Cisco recommends RSA key sizes of 2048 or greater for security. Shorter key sizes will be rejected in future releases. - "Regenerate keys specifying key size to be 2048 or greater" " to avoid future service disruption" CRYPTO_ENGINE-4-CSDL_COMPLIANCE_RSA_WEAK_KEYS 4-Warning RSA keypair [chars] is in violation of Cisco security compliance guidelines and will be rejected by future releases. An attempt to use RSA cryptography with weak keys has been detected. Cisco recommends RSA key sizes of 2048 or greater for security. Shorter key sizes will be rejected in future releases. - "Regenerate keys specifying key size to be 2048 or greater" " to avoid future service disruption" CRYPTO_ENGINE-5-CSDL_COMPLIANCE_ENFORCED 5-Notice Cisco PSB security compliance is being enforced Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced. - "No action is required" CRYPTO_ENGINE-5-CSDL_COMPLIANCE_ENFORCED 5-Notice Cisco PSB security compliance is being enforced Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced. - "No action is required" CRYPTO_ENGINE-5-CSDL_COMPLIANCE_EXCEPTION_ADDED 5-Notice Cisco PSB security compliance exception has been added by [chars] for use of [chars] Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced. - "No action is required" CRYPTO_ENGINE-5-CSDL_COMPLIANCE_EXCEPTION_ADDED 5-Notice Cisco PSB security compliance exception has been added by [chars] for use of [chars] Cisco Internal Requirements and defined by the Cisco Product Security Baseline PSB are being enforced. - "No action is required" CRYPTO_ENGINE-5-KEY_ADDITION 5-Notice A key named [chars] has been generated or imported by [chars] An RSA or EC key has been generated or imported. The configuration must be saved to permanently save this key. - "No action required. Informational message" CRYPTO_ENGINE-5-KEY_ADDITION 5-Notice A key named [chars] has been generated or imported by [chars] An RSA or EC key has been generated or imported. The configuration must be saved to permanently save this key. - "No action required. Informational message" CRYPTO_ENGINE-5-KEY_DELETED 5-Notice A key named [chars] has been removed from key storage A key has been marked for removal from storage. The configuration must be saved to permanently remove this key. - "No action required. Informational message" CRYPTO_ENGINE-5-KEY_DELETED 5-Notice A key named [chars] has been removed from key storage A key has been marked for removal from storage. The configuration must be saved to permanently remove this key. - "No action required. Informational message" CRYPTO_ENGINE-5-KEY_REPLACE 5-Notice A key named [chars] has been replaced by [chars] with new key data An RSA or EC key has been replaced. The configuration must be saved to permanently save this key. - "No action required. Informational message" CRYPTO_ENGINE-5-KEY_REPLACE 5-Notice A key named [chars] has been replaced by [chars] with new key data An RSA or EC key has been replaced. The configuration must be saved to permanently save this key. - "No action required. Informational message" CRYPTO_HA_IKE-3-FAILOVER_ERROR 3-Error Attempt to failover IKE SA [inet]:[inet] failed due to [chars]. No The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA. ipsec-ha "Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure." CRYPTO_HA_IKE-3-FAILOVER_ERROR 3-Error Attempt to failover IKE SA [inet]:[inet] failed due to [chars]. No The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA. ipsec-ha "Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure." CRYPTO_HA_IKE-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW 4-Warning Crypto hardware is enabled and it does not support HA operation '[chars]' Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys - "Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine" CRYPTO_HA_IKE-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW 4-Warning Crypto hardware is enabled and it does not support HA operation '[chars]' Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys - "Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine" CRYPTO_HA_IPSEC-3-FAILOVER_ERROR 3-Error Attempt to failover IPSec SA [inet]:[inet] failed due to [chars]. No The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA. ipsec-ha "Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure." CRYPTO_HA_IPSEC-3-FAILOVER_ERROR 3-Error Attempt to failover IPSec SA [inet]:[inet] failed due to [chars]. No The HA Active device attempted to checkpoint the state of an IKE SA to the Standby but the Standby device was unable to create the Standby IKE SA. ipsec-ha "Look for other error messages at log level WARNING or turn on debugs " "to look for the specific reason of the failure." CRYPTO_HA_IPSEC-3-HA_IPSEC_UPDATE_PROC_FAIL 3-Error Start of HA IPSec update process failed Starting of the IPSec HA process failed Updates will not be sent from active to standby ipsec-ha "The box may need to be re-booted if this is a part " "of a IPSec HA setup" CRYPTO_HA_IPSEC-3-HA_IPSEC_UPDATE_PROC_FAIL 3-Error Start of HA IPSec update process failed Starting of the IPSec HA process failed Updates will not be sent from active to standby ipsec-ha "The box may need to be re-booted if this is a part " "of a IPSec HA setup" CRYPTO_HA_IPSEC-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW 4-Warning Crypto hardware is enabled and it does not support HA operation '[chars]' Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys - "Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine" CRYPTO_HA_IPSEC-4-CRYPTO_HA_NOT_SUPPORTED_BY_HW 4-Warning Crypto hardware is enabled and it does not support HA operation '[chars]' Crypto Hardware is enabled but the hardware does not support HA operations like insert/extract of keys - "Replace Cryto hardware with one that support HA operations" " or disable the hardware to use software crypto engine" CRYPTO_RSA_ISSU-3-GET_BUFFER 3-Error Crypto RSA ISSU client failed to get buffer for message.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to get buffer for building\n\ a negotiation message. Hence it cannot send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. crypto_rsa "show logging and show checkpoint client" CRYPTO_RSA_ISSU-3-GET_BUFFER 3-Error Crypto RSA ISSU client failed to get buffer for message.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to get buffer for building\n\ a negotiation message. Hence it cannot send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. crypto_rsa "show logging and show checkpoint client" CRYPTO_RSA_ISSU-3-INIT 3-Error Crypto RSA ISSU client initialization failed to [chars]. Error: [dec] [chars] Crypto RSA ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. crypto_rsa LOG_STD_SH_TECH_ACTION CRYPTO_RSA_ISSU-3-INIT 3-Error Crypto RSA ISSU client initialization failed to [chars]. Error: [dec] [chars] Crypto RSA ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. crypto_rsa LOG_STD_SH_TECH_ACTION CRYPTO_RSA_ISSU-3-INVALID_SESSION 3-Error Crypto RSA ISSU client does not have a valid registered session. Crypto RSA ISSU client does not have a valid registered session.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. crypto_rsa "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-INVALID_SESSION 3-Error Crypto RSA ISSU client does not have a valid registered session. Crypto RSA ISSU client does not have a valid registered session.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. crypto_rsa "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-MSG_NOT_OK 3-Error Crypto RSA ISSU client message type [dec] is not compatible Crypto RSA ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it cannot be processed by this unit crypto_rsa "show issu message group and\n\ show issu session and\n\ show issu negotiated version " CRYPTO_RSA_ISSU-3-MSG_NOT_OK 3-Error Crypto RSA ISSU client message type [dec] is not compatible Crypto RSA ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it cannot be processed by this unit crypto_rsa "show issu message group and\n\ show issu session and\n\ show issu negotiated version " CRYPTO_RSA_ISSU-3-MSG_SIZE 3-Error Crypto RSA ISSU client failed to get the MTU for message type [dec].\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to calculate MTU\n\ for the message specified. The dot1x ISSU client will not\n\ be able to send message to the standby unit. crypto_rsa "show issu message group and\n\ show issu session and\n\ show issu negotiated version " CRYPTO_RSA_ISSU-3-MSG_SIZE 3-Error Crypto RSA ISSU client failed to get the MTU for message type [dec].\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to calculate MTU\n\ for the message specified. The dot1x ISSU client will not\n\ be able to send message to the standby unit. crypto_rsa "show issu message group and\n\ show issu session and\n\ show issu negotiated version " CRYPTO_RSA_ISSU-3-SEND_NEGO_FAILED 3-Error Crypto RSA ISSU client failed to send negotiation message.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to send a session negotiation\n\ message to the peer. When there is a problem in the ISSU\n\ negotiation the standby unit can not be brought up. crypto_rsa "show logging and show checkpoint client" CRYPTO_RSA_ISSU-3-SEND_NEGO_FAILED 3-Error Crypto RSA ISSU client failed to send negotiation message.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to send a session negotiation\n\ message to the peer. When there is a problem in the ISSU\n\ negotiation the standby unit can not be brought up. crypto_rsa "show logging and show checkpoint client" CRYPTO_RSA_ISSU-3-SESSION_NEGO 3-Error Crypto RSA ISSU client encountered unexpected client nego_done.\n\ Error: [dec] [chars] Crypto RSA ISSU client encountered an unexpected 'client\n\ negotiation done'. crypto_rsa "show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-SESSION_NEGO 3-Error Crypto RSA ISSU client encountered unexpected client nego_done.\n\ Error: [dec] [chars] Crypto RSA ISSU client encountered an unexpected 'client\n\ negotiation done'. crypto_rsa "show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-SESSION_REGISTRY 3-Error Crypto RSA ISSU client failed to register session information.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to register session information.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. crypto_rsa "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-SESSION_REGISTRY 3-Error Crypto RSA ISSU client failed to register session information.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to register session information.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. crypto_rsa "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-SESSION_UNREGISTRY 3-Error Crypto RSA ISSU client failed to unregister session information.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to unregister session information. crypto_rsa "show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-SESSION_UNREGISTRY 3-Error Crypto RSA ISSU client failed to unregister session information.\n\ Error: [dec] [chars] Crypto RSA ISSU client failed to unregister session information. crypto_rsa "show issu session and\n\ show issu negotiated capability " CRYPTO_RSA_ISSU-3-TRANSFORM_FAIL 3-Error Crypto RSA ISSU client [chars] transform failed for message type [dec].\n\ Error: [dec] [chars] Crypto RSA ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Crypto RSA state will not\n\ be indentical with the active unit. crypto_rsa "show issu session and\n\ show issu negotiated version " CRYPTO_RSA_ISSU-3-TRANSFORM_FAIL 3-Error Crypto RSA ISSU client [chars] transform failed for message type [dec].\n\ Error: [dec] [chars] Crypto RSA ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Crypto RSA state will not\n\ be indentical with the active unit. crypto_rsa "show issu session and\n\ show issu negotiated version " CRYPTO_SL_TP_LEVELS-3-INV_DEFAULT_VALUE 3-Error Invalid platform default value token: [chars] - - LOG_STD_ACTION CRYPTO_SL_TP_LEVELS-3-INV_PLATFORM_VALUE 3-Error Invalid platform level value token: [chars] - - LOG_STD_ACTION CRYPTO_SL_TP_LEVELS-3-NO_VALID_PLATFORM_VALUES 3-Error No valid platform level values specified - - LOG_STD_ACTION CRYPTO_SL_TP_LEVELS-3-ROMMON_WRITE_FAILED 3-Error Error in updating rommon variable - - LOG_STD_ACTION CRYPTO_SL_TP_LEVELS-3-VAR_SET_FAILED 3-Error Update of rommon variable failed: retcode=[dec] Call to update rommon variable failed - LOG_STD_ACTION CRYPTO_SL_TP_LEVELS-6-INV_ROMMON_VALUE 6-Information Invalid throughput option [dec] kbps foundupdating rommon to [dec] kbps Invalid throughput option in rommon for crypto throughputResetting the throughput option to the default value - "No action required. Informational message." CRYPTO_SL_TP_LEVELS-6-ROMMON_VAL 6-Information Current rommon value: [chars] - - - CRYPTO_SL_TP_LEVELS-6-TIER_BASED_LIC 6-Information Tier Based License Support: [dec] - - - CRYPTO_SL_TP_LEVELS-6-TP_LEVEL_BLOCKED 6-Information Network Essentials is enabled higher throughput blocked - - - CRYPTO_SL_TP_LEVELS-6-TP_LEVEL_LIMITED 6-Information HSECK9 is disabled: bandwidth restricted to 250Mbps - - - CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_HSEC_REGISTER_FAILED 6-Information License registration failed rc=[dec] License request failed. - "Look at other logs/debugs to see reason for failure." CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_HSEC_REQUEST_FAILED 6-Information License request failed rc=[dec] HSECK9 License request failed. - "Look at other logs/debugs to see reason for failure." CRYPTO_SL_TP_LEVELS-6-TP_LICENSE_TP_REQUEST_FAILED 6-Information License request failed rc=[dec] sle_ret_val=[dec] License request failed. Data plane will use platform default throughput level - "Look at other logs/debugs to see reason for failure." CRYPTO_SL_TP_LEVELS-6-TP_THROTTLE_STATE 6-Information Crypto throughput [chars] throttled. New level is [dec] Maximum throughput level is the same as unthrottled. All other levels are throttled - "No action required. Informational message." CRYPTO_SL_TP_LEVELS-6-VAR_NEW_STR 6-Information Setting crypto bidir throughput to: [chars] Crypto throughput rommon var updated - "No action required. Informational message." CRYPTO_SL_TP_LEVELS-6-VAR_NEW_VALUE 6-Information Setting crypto bidir throughput to: [dec] kbps Crypto throughput rommon var updated - "No action required. Informational message." CRYPTO-0-AUDITFAIL 0-Emergency Encryption audit check found the wrong level of encryption in this image The device is starting the Crypto algorithms self-tests.\n\ Success or failure status will be reported when the tests complete. - "Informational only. No action required." CRYPTO-0-AUDITFAIL 0-Emergency Encryption audit check found the wrong level of encryption in this image The device is starting the Crypto algorithms self-tests.\n\ Success or failure status will be reported when the tests complete. - "Informational only. No action required." CRYPTO-0-SELF_TEST_FAILURE 0-Emergency Crypto algorithms self-test failed [chars] One of the crypto algorithm self-tests has failed. The crypto algorithm engine is not operable in this state. - "If the failure persists contact Cisco to " "obtain a replacement IOS image." CRYPTO-0-SELF_TEST_FAILURE 0-Emergency Crypto algorithms self-test failed [chars] One of the crypto algorithm self-tests has failed. The crypto algorithm engine is not operable in this state. - "If the failure persists contact Cisco to " "obtain a replacement IOS image." CRYPTO-3-BADMAGIC 3-Error Bad [chars] magic number %04x. An internal software error. ipsec LOG_STD_ACTION CRYPTO-3-BADMAGIC 3-Error Bad [chars] magic number %04x. An internal software error. ipsec LOG_STD_ACTION CRYPTO-3-ECDSA_SELFTEST_FAILED 3-Error Generated ECDSA key failed self test An automatic test of the newly generated ECDSA keypair [chars] failed. That ECDSA key was automatically deleted. - "File a DDTS. As an immediate workaround attempt to create another pair" CRYPTO-3-ECDSA_SELFTEST_FAILED 3-Error Generated ECDSA key failed self test An automatic test of the newly generated ECDSA keypair [chars] failed. That ECDSA key was automatically deleted. - "File a DDTS. As an immediate workaround attempt to create another pair" CRYPTO-3-ENGINE_BAD_ID 3-Error Crypto Engine id [dec] is invalid The packet has its engine_id set to something other than software crypto or hardware crypto. Unable to determine which crypto engine to use The packet will be default sent to software crypto engine. ipsec "No action required" CRYPTO-3-ENGINE_BAD_ID 3-Error Crypto Engine id [dec] is invalid The packet has its engine_id set to something other than software crypto or hardware crypto. Unable to determine which crypto engine to use The packet will be default sent to software crypto engine. ipsec "No action required" CRYPTO-3-EZVPN_VINTERFACE_CREATE_ERR 3-Error EZVPN[chars]: Virtual-access interface creation failed The virtual-interface feature will not work without a virtual-access interface. The EzVPN configuration is unusable. You can choose to remove virtual-interface configuration from ezvpn as a workaround ipsec-ezvpn "If this message occurs contact your technical " "support representative." CRYPTO-3-EZVPN_VINTERFACE_CREATE_ERR 3-Error EZVPN[chars]: Virtual-access interface creation failed The virtual-interface feature will not work without a virtual-access interface. The EzVPN configuration is unusable. You can choose to remove virtual-interface configuration from ezvpn as a workaround ipsec-ezvpn "If this message occurs contact your technical " "support representative." CRYPTO-3-GM_FAILCLOSE_UNSUPPORTED 3-Error GETVPN failclose is not supported by the current available crypto hardware. An attempt was made to configure the GETVPN failclose feature which cannot be supported by the current encryption hardware. ipsec-mcast "Please remove the unsupported feature config " "or switch to a capable crypto engine." CRYPTO-3-GM_FAILCLOSE_UNSUPPORTED 3-Error GETVPN failclose is not supported by the current available crypto hardware. An attempt was made to configure the GETVPN failclose feature which cannot be supported by the current encryption hardware. ipsec-mcast "Please remove the unsupported feature config " "or switch to a capable crypto engine." CRYPTO-3-IKE_PAK_IN_Q_TIME_LIMIT_EXCEED 3-Error Pak spent too much time in the IKE input queues An incoming IKE packet spent too much time in the IKE input\n\ queues. This can happen when the IKE subsystem is under heavy\n\ load due to a lot of peers trying to setup SAs simultaneously\n\ and IKE is not able to handle all the incoming packets in a\n\ timely manner. - "It is important to understand why many peers are simultaneously\n\ trying to setup SAs at the same time. If possible try to avoid\n\ or minimize such network conditions." CRYPTO-3-IKE_PAK_IN_Q_TIME_LIMIT_EXCEED 3-Error Pak spent too much time in the IKE input queues An incoming IKE packet spent too much time in the IKE input\n\ queues. This can happen when the IKE subsystem is under heavy\n\ load due to a lot of peers trying to setup SAs simultaneously\n\ and IKE is not able to handle all the incoming packets in a\n\ timely manner. - "It is important to understand why many peers are simultaneously\n\ trying to setup SAs at the same time. If possible try to avoid\n\ or minimize such network conditions." CRYPTO-3-IKEINIT 3-Error [chars] An IKE initialization error ipsec LOG_STD_ACTION CRYPTO-3-IKEINIT 3-Error [chars] An IKE initialization error ipsec LOG_STD_ACTION CRYPTO-3-IKMP_PEER_INIT_FAILURE 3-Error IKE failed to create IKE peer tree or leaf node. IKE failed to allocate memory for the IKE peer tree - "More DRAM may be required in order to run the image." CRYPTO-3-IKMP_PEER_INIT_FAILURE 3-Error IKE failed to create IKE peer tree or leaf node. IKE failed to allocate memory for the IKE peer tree - "More DRAM may be required in order to run the image." CRYPTO-3-IKMP_QUERY_KEY 3-Error Querying key pair failed. Querying public key/private key using subject name failed - "Check the subject name in the certificate." CRYPTO-3-IKMP_QUERY_KEY 3-Error Querying key pair failed. Querying public key/private key using subject name failed - "Check the subject name in the certificate." CRYPTO-3-INVALID_KMI_REQUEST 3-Error Invalid KMI error: kmi_client: [dec] in processing [chars] IPSec detected an invalid KMI ipsec-core "None" CRYPTO-3-INVALID_KMI_REQUEST 3-Error Invalid KMI error: kmi_client: [dec] in processing [chars] IPSec detected an invalid KMI ipsec-core "None" CRYPTO-3-IPSEC_PAL_FATAL_ERROR 3-Error IPsec PAL Fatal Error: [chars] IPSec SM detected inconsistence and hence crashing the system ipsec-core "None" CRYPTO-3-IPSEC_PAL_FATAL_ERROR 3-Error IPsec PAL Fatal Error: [chars] IPSec SM detected inconsistence and hence crashing the system ipsec-core "None" CRYPTO-3-IPSECV6_UNSUPPORTED 3-Error IPv6 IPsec is not supported by the current available crypto hardware. An attempt was made to configure a feature which will use IPv6 IPsec. IPv6 IPsec cannot be supported by the current encryption hardware. The configuration change was made but will not be functional until the encryption hardware configuration is changed. ipsec "Please remove the unsupported feature config " "or switch to a capable crypto engine." CRYPTO-3-IPSECV6_UNSUPPORTED 3-Error IPv6 IPsec is not supported by the current available crypto hardware. An attempt was made to configure a feature which will use IPv6 IPsec. IPv6 IPsec cannot be supported by the current encryption hardware. The configuration change was made but will not be functional until the encryption hardware configuration is changed. ipsec "Please remove the unsupported feature config " "or switch to a capable crypto engine." CRYPTO-3-MTREE_CMD_BLOCK 3-Error Mtree command [dec] was blocked from the the mtree process queue. An attempt was made to enqueue a command to the crypto mtree manager process even though IPsec is currently operating in HAPX mode. ipsec LOG_STD_ACTION CRYPTO-3-MTREE_CMD_BLOCK 3-Error Mtree command [dec] was blocked from the the mtree process queue. An attempt was made to enqueue a command to the crypto mtree manager process even though IPsec is currently operating in HAPX mode. ipsec LOG_STD_ACTION CRYPTO-3-NOSOCKET 3-Error Unable to open [chars] Call Admission Control is configured globally or at the IKE level on this device. Consequently an IKE SA request was denied do to the reason described in the error message. ipsec "Decrease the number of concurrent connections or " "inspect the crypto engine." CRYPTO-3-NOSOCKET 3-Error Unable to open [chars] Call Admission Control is configured globally or at the IKE level on this device. Consequently an IKE SA request was denied do to the reason described in the error message. ipsec "Decrease the number of concurrent connections or " "inspect the crypto engine." CRYPTO-3-PAL_INTERNAL_ERROR 3-Error Internal error: [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR 3-Error Internal error: [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_ALREADY_ALWAYS 3-Error Internal error: Cannot do transition for state [chars]: ALWAYS state already defined IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_ALREADY_ALWAYS 3-Error Internal error: Cannot do transition for state [chars]: ALWAYS state already defined IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_BAD_MESSAGE 3-Error Internal error: unrecognized message [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_BAD_MESSAGE 3-Error Internal error: unrecognized message [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_BAD_TRANSITION 3-Error Internal error: state [chars] has unrecognized transition [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_BAD_TRANSITION 3-Error Internal error: state [chars] has unrecognized transition [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_CANNOT_ALWAYS 3-Error Internal error: Cannot do ALWAYS transition for state [chars]: transition already defined IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_CANNOT_ALWAYS 3-Error Internal error: Cannot do ALWAYS transition for state [chars]: transition already defined IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_LOOP 3-Error Internal error: [[chars]]: state loop detected: state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_LOOP 3-Error Internal error: [[chars]]: state loop detected: state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_NO_NEXT_STATE 3-Error Internal error: undefined next state [dec]: previous state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_NO_NEXT_STATE 3-Error Internal error: undefined next state [dec]: previous state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_REQUEST_STATE 3-Error Internal error: illegal request state [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_REQUEST_STATE 3-Error Internal error: illegal request state [dec] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_STATE_ALREADY_DEFINED 3-Error Internal error: State [dec] already defined: old_state = [chars] new_state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_STATE_ALREADY_DEFINED 3-Error Internal error: State [dec] already defined: old_state = [chars] new_state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_STATE_OVERFLOW 3-Error Internal error: Table overflow new_state = [dec] [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_STATE_OVERFLOW 3-Error Internal error: Table overflow new_state = [dec] [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_ALREADY 3-Error Internal error: Transition [dec] already defined: state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_ALREADY 3-Error Internal error: Transition [dec] already defined: state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_OVERFLOW 3-Error Internal error: Transition table overflow transition = [dec] state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_INTERNAL_ERROR_TRANSITION_OVERFLOW 3-Error Internal error: Transition table overflow transition = [dec] state = [chars] IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_REQUEST_OUTSIDE_ACTION 3-Error Internal error: [chars] called from outside action routine IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_REQUEST_OUTSIDE_ACTION 3-Error Internal error: [chars] called from outside action routine IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_REQUEST_PENDING_ACTION 3-Error Internal error: state [chars] has pending actions IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-PAL_REQUEST_PENDING_ACTION 3-Error Internal error: state [chars] has pending actions IPSec detected a serious internal error ipsec-core "None" CRYPTO-3-POLICY_CKSUM_ERROR 3-Error Crypto policy checksum failure.\n \tCrypto access list [chars] crypto map [chars] interface [chars]\n Crypto policy checksum failure has been detected in this router whose traffic is protected by the crypto policy. This event may be caused by memory corruption occuring in crypto policy data or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the router has been forced to reload. - "Contact your Cisco support representatives." CRYPTO-3-POLICY_CKSUM_ERROR 3-Error Crypto policy checksum failure.\n \tCrypto access list [chars] crypto map [chars] interface [chars]\n Crypto policy checksum failure has been detected in this router whose traffic is protected by the crypto policy. This event may be caused by memory corruption occuring in crypto policy data or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the router has been forced to reload. - "Contact your Cisco support representatives." CRYPTO-3-RSA_SELFTEST_FAILED 3-Error Generated RSA key failed self test An automatic test of the newly generated RSA keypair [chars] failed. That RSA key was automatically deleted. - "File a DDTS. As an immediate workaround attempt to create another pair" CRYPTO-3-RSA_SELFTEST_FAILED 3-Error Generated RSA key failed self test An automatic test of the newly generated RSA keypair [chars] failed. That RSA key was automatically deleted. - "File a DDTS. As an immediate workaround attempt to create another pair" CRYPTO-3-TOKENADMINLOCKEDOUT 3-Error Cryptographic Token [chars] Administrator PIN Locked due to too many unsuccessful login attempts The cryptographic token has disabled the Admin PIN due to too many login failures pki "If the user PIN is also locked out it will be necessary to reinitialize the card." "The data on the card will be lost" CRYPTO-3-TOKENADMINLOCKEDOUT 3-Error Cryptographic Token [chars] Administrator PIN Locked due to too many unsuccessful login attempts The cryptographic token has disabled the Admin PIN due to too many login failures pki "If the user PIN is also locked out it will be necessary to reinitialize the card." "The data on the card will be lost" CRYPTO-3-TOKENADMINLOGINFAILED 3-Error Cryptographic Token [chars] ADMIN Login FAILED The cryptographic token has rejected the administrator PIN offered by the router pki "Issue 'crypto pki token admin-pin' command to enter correct PIN" CRYPTO-3-TOKENADMINLOGINFAILED 3-Error Cryptographic Token [chars] ADMIN Login FAILED The cryptographic token has rejected the administrator PIN offered by the router pki "Issue 'crypto pki token admin-pin' command to enter correct PIN" CRYPTO-3-TOKENAPIFAILURE 3-Error Cryptographic Token [chars] API FAILED error = [dec] The cryptographic token returned an unexpected error pki LOG_STD_ACTION CRYPTO-3-TOKENAPIFAILURE 3-Error Cryptographic Token [chars] API FAILED error = [dec] The cryptographic token returned an unexpected error pki LOG_STD_ACTION CRYPTO-3-TOKENCHANGEPINFAILED 3-Error Cryptographic Token [chars] Change PIN FAILED The cryptographic token has rejected the new PIN offered by the router pki "Be sure you are logged in to the token as admin. Try a longer PIN." CRYPTO-3-TOKENCHANGEPINFAILED 3-Error Cryptographic Token [chars] Change PIN FAILED The cryptographic token has rejected the new PIN offered by the router pki "Be sure you are logged in to the token as admin. Try a longer PIN." CRYPTO-3-TOKENLOCKEDOUT 3-Error Cryptographic Token [chars] PIN Locked due to too many unsuccessful login attempts The cryptographic token has disabled the user PIN due to too many login failures pki "Issue 'crypto pki token admin-pin' command to enter correct ADMINISTRATOR PIN" CRYPTO-3-TOKENLOCKEDOUT 3-Error Cryptographic Token [chars] PIN Locked due to too many unsuccessful login attempts The cryptographic token has disabled the user PIN due to too many login failures pki "Issue 'crypto pki token admin-pin' command to enter correct ADMINISTRATOR PIN" CRYPTO-3-TOKENLOGINFAILED 3-Error Cryptographic Token [chars] Login FAILED The cryptographic token has rejected the PIN offered by the router pki "Issue 'crypto pki token user-pin' command to enter correct PIN" CRYPTO-3-TOKENLOGINFAILED 3-Error Cryptographic Token [chars] Login FAILED The cryptographic token has rejected the PIN offered by the router pki "Issue 'crypto pki token user-pin' command to enter correct PIN" CRYPTO-3-TOKENSTOREKEYFAILED 3-Error Key [chars] store on Cryptographic Token [chars] Failed An error occurred attempting to write a new keypair out to the cryptographic token pki "Try logging in to the token. If the error persists " "try logging in as admin" CRYPTO-3-TOKENSTOREKEYFAILED 3-Error Key [chars] store on Cryptographic Token [chars] Failed An error occurred attempting to write a new keypair out to the cryptographic token pki "Try logging in to the token. If the error persists " "try logging in as admin" CRYPTO-4-ADV_IPSERVICES_LIC_NOT_ENABLED 4-Warning advipservices license is required to enable IPSec IPv6 feature. Please install the license and retry.\n IPSec IPv6 subsystem is bundled with advipservices license. So check if this license is enabled to include IPSec IPv6 subsystem. ipsec-core "Enable ADV_IPSERVICES license." CRYPTO-4-ADV_IPSERVICES_LIC_NOT_ENABLED 4-Warning advipservices license is required to enable IPSec IPv6 feature. Please install the license and retry.\n IPSec IPv6 subsystem is bundled with advipservices license. So check if this license is enabled to include IPSec IPv6 subsystem. ipsec-core "Enable ADV_IPSERVICES license." CRYPTO-4-AUDITWARN 4-Warning Encryption audit check could not be performed The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration. - "Manually verify that this IOS image is entitled to contain " "encryption." CRYPTO-4-AUDITWARN 4-Warning Encryption audit check could not be performed The audit check verifying encryption entitlement within the IOS image could not be performed due to incompete system configuration. - "Manually verify that this IOS image is entitled to contain " "encryption." CRYPTO-4-ENC_METHOD_NOT_SUPPORTED 4-Warning Invalid encryption method for IKE policy [dec] Configured encryption method is not supported - "Use any of the valid encryption methods for the ISAKMP policy" CRYPTO-4-ENC_METHOD_NOT_SUPPORTED 4-Warning Invalid encryption method for IKE policy [dec] Configured encryption method is not supported - "Use any of the valid encryption methods for the ISAKMP policy" CRYPTO-4-EZVPN_FAILED_TO_CONNECT 4-Warning [chars] Ezvpn session failed to come up ezvpn is stuck in a state waiting for an event posting a reset message to recover. - "" CRYPTO-4-EZVPN_FAILED_TO_CONNECT 4-Warning [chars] Ezvpn session failed to come up ezvpn is stuck in a state waiting for an event posting a reset message to recover. - "" CRYPTO-4-EZVPN_SA_LIMIT 4-Warning [chars] The limit for maximum no of ezvpn tunnels that can be setup on the platform has reached. Active SAs shall not be terminated but no additional SAs can be established until the number of existing SAs decreases. - "" CRYPTO-4-EZVPN_SA_LIMIT 4-Warning [chars] The limit for maximum no of ezvpn tunnels that can be setup on the platform has reached. Active SAs shall not be terminated but no additional SAs can be established until the number of existing SAs decreases. - "" CRYPTO-4-GM_ISAKMP_OFF 4-Warning Can't start GDOI registration as ISAKMP disabled Crypto ISAKMP is not enabled ipsec-mcast "Enable crypto ISAKMP" CRYPTO-4-GM_ISAKMP_OFF 4-Warning Can't start GDOI registration as ISAKMP disabled Crypto ISAKMP is not enabled ipsec-mcast "Enable crypto ISAKMP" CRYPTO-4-GM_LOCAL_ADDRESS 4-Warning Failed to determine local ip address for group [chars] on interface [chars] Failed to determine local address for GDOI crypto map ipsec-mcast LOG_STD_ACTION CRYPTO-4-GM_LOCAL_ADDRESS 4-Warning Failed to determine local ip address for group [chars] on interface [chars] Failed to determine local address for GDOI crypto map ipsec-mcast LOG_STD_ACTION CRYPTO-4-GM_REGSTER_IF_DOWN 4-Warning Can't start GDOI registeration as interface [chars] is down Interface is found down before registration ipsec-mcast LOG_STD_ACTION CRYPTO-4-GM_REGSTER_IF_DOWN 4-Warning Can't start GDOI registeration as interface [chars] is down Interface is found down before registration ipsec-mcast LOG_STD_ACTION CRYPTO-4-GM_ZERO_ADDRESS 4-Warning No ip address found for group [chars] on source interface [chars] Souce IP address for GDOI crypto map is zero ipsec-mcast LOG_STD_ACTION CRYPTO-4-GM_ZERO_ADDRESS 4-Warning No ip address found for group [chars] on source interface [chars] Souce IP address for GDOI crypto map is zero ipsec-mcast LOG_STD_ACTION CRYPTO-4-IA_CLEARTEXT 4-Warning Unencrypted traffic [chars] [inet] because crypto optional is configured Cleartext traffic is passing through an interface that is configured for encryption. This traffic is accepted because the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows such traffic. ipsec "If you did not intend to configure the crypto " "optional setting you should reconfigure the box " "to turn it off" CRYPTO-4-IA_CLEARTEXT 4-Warning Unencrypted traffic [chars] [inet] because crypto optional is configured Cleartext traffic is passing through an interface that is configured for encryption. This traffic is accepted because the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows such traffic. ipsec "If you did not intend to configure the crypto " "optional setting you should reconfigure the box " "to turn it off" CRYPTO-4-IA_ENABLE 4-Warning Security warning: crypto ipsec optional is configured Currently the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows data which normally would be encrypted to be sent in the clear. ipsec "If you did not intend to configure the crypto " "optional setting you should reconfigure the box to turn " "it off" CRYPTO-4-IA_ENABLE 4-Warning Security warning: crypto ipsec optional is configured Currently the router has the CRYPTO IPSEC OPTIONAL ENABLE setting which allows data which normally would be encrypted to be sent in the clear. ipsec "If you did not intend to configure the crypto " "optional setting you should reconfigure the box to turn " "it off" CRYPTO-4-IKE_DEFAULT_POLICY_ACCEPTED 4-Warning IKE default policy was matched and is being used. The default policy is being used because the local configured policies did not match with the peer's policies. ipsec-isakmp "To avoid using the default policy " "reconfigure the local policy to match " "with peer's policy" CRYPTO-4-IKE_DEFAULT_POLICY_ACCEPTED 4-Warning IKE default policy was matched and is being used. The default policy is being used because the local configured policies did not match with the peer's policies. ipsec-isakmp "To avoid using the default policy " "reconfigure the local policy to match " "with peer's policy" CRYPTO-4-IKE_QUICKMODE_BAD_CERT 4-Warning encrypted connection attempted with a peer without the\n configured certificate attributes An encrypting peer attempted to establish an IPSec session with an interface which it was not authorized for. Some might consider this a hostile event. - "Check if the peer should be authorized to connect with the" " IPSec connection. If he should be allowed it may be a" " configuration issue. Otherwise you should contact the" " peer's administrator." CRYPTO-4-IKE_QUICKMODE_BAD_CERT 4-Warning encrypted connection attempted with a peer without the\n configured certificate attributes An encrypting peer attempted to establish an IPSec session with an interface which it was not authorized for. Some might consider this a hostile event. - "Check if the peer should be authorized to connect with the" " IPSec connection. If he should be allowed it may be a" " configuration issue. Otherwise you should contact the" " peer's administrator." CRYPTO-4-IKMP_BAD_MESSAGE 4-Warning IKE message from [chars] failed its sanity check or is malformed A quick sanity check is done on all received ISAKMP messages to verify that all component payload types are valid and that the sum of their individual lengths equals the total length of the received message. This message failed the sanity check. Persistantly bad messages could be a denial of service attack or bad decryption. - "Contact the remote peer's administrator." CRYPTO-4-IKMP_BAD_MESSAGE 4-Warning IKE message from [chars] failed its sanity check or is malformed A quick sanity check is done on all received ISAKMP messages to verify that all component payload types are valid and that the sum of their individual lengths equals the total length of the received message. This message failed the sanity check. Persistantly bad messages could be a denial of service attack or bad decryption. - "Contact the remote peer's administrator." CRYPTO-4-IKMP_HASH_SIZE_EXCEEDED 4-Warning IKE hash size exceeded with peer at [inet]. A hash operation required by the IKE protocol exceeded an internal limit. The IKE SA negotiation was rejected. That can happen if an inordinately large number of IKE policies were being proposed by the initiator - "Reduce the number of configured IKE policies." CRYPTO-4-IKMP_HASH_SIZE_EXCEEDED 4-Warning IKE hash size exceeded with peer at [inet]. A hash operation required by the IKE protocol exceeded an internal limit. The IKE SA negotiation was rejected. That can happen if an inordinately large number of IKE policies were being proposed by the initiator - "Reduce the number of configured IKE policies." CRYPTO-4-IKMP_INVALID_POLICY 4-Warning ISAKMP policy rsa-encr not supported by crypto HW accelerator [chars] rsa-encr is not supported by Hifn based crypto HW accelerators - "Use ISAKMP policy rsa-sig" CRYPTO-4-IKMP_INVALID_POLICY 4-Warning ISAKMP policy rsa-encr not supported by crypto HW accelerator [chars] rsa-encr is not supported by Hifn based crypto HW accelerators - "Use ISAKMP policy rsa-sig" CRYPTO-4-IKMP_ISR_LIMIT_MAX 4-Warning INV SPI RECOV LIMIT [dec] maxed [chars] [chars] [chars] INVALID SPI RECOVERY SAs maximum limit has been reached. - "Possibly the local box reloaded." CRYPTO-4-IKMP_ISR_LIMIT_MAX 4-Warning INV SPI RECOV LIMIT [dec] maxed [chars] [chars] [chars] INVALID SPI RECOVERY SAs maximum limit has been reached. - "Possibly the local box reloaded." CRYPTO-4-IKMP_NO_SA 4-Warning IKE message from [chars] has no SA and is not an initialization offer IKE maintains state for a communication in the form of security associations. No security association exists for this packet and it is not an initial offer from the peer to establish one. This situation could denote a denial of service attack. - "Contact the remote peer and/or his administrator" CRYPTO-4-IKMP_NO_SA 4-Warning IKE message from [chars] has no SA and is not an initialization offer IKE maintains state for a communication in the form of security associations. No security association exists for this packet and it is not an initial offer from the peer to establish one. This situation could denote a denial of service attack. - "Contact the remote peer and/or his administrator" CRYPTO-4-IKMP_PKT_OVERFLOW 4-Warning ISAKMP message from [chars] larger %ld than the UDP packet length %ld - - - CRYPTO-4-IKMP_PKT_OVERFLOW 4-Warning ISAKMP message from [chars] larger %ld than the UDP packet length %ld - - - CRYPTO-4-IPSEC_AAA_START_FAILURE 4-Warning IPSEC Accounting was unable to send start record The AAA subsystem was unable to send the accounting start on behalf of IPSec. This could be due to the AAA Server being unreachable. ipsec "Ensure that the AAA server is reachable and enabled" "for accounting." CRYPTO-4-IPSEC_AAA_START_FAILURE 4-Warning IPSEC Accounting was unable to send start record The AAA subsystem was unable to send the accounting start on behalf of IPSec. This could be due to the AAA Server being unreachable. ipsec "Ensure that the AAA server is reachable and enabled" "for accounting." CRYPTO-4-IPSEC_AAA_STOP_FAILURE 4-Warning IPSEC Accounting was unable to send stop record The AAA subsystem was unable to send the accounting stop on behalf of IPSec. This could be due to the AAA Server being unreachable. ipsec "Ensure that the AAA server is reachable and enabled" "for accounting." CRYPTO-4-IPSEC_AAA_STOP_FAILURE 4-Warning IPSEC Accounting was unable to send stop record The AAA subsystem was unable to send the accounting stop on behalf of IPSec. This could be due to the AAA Server being unreachable. ipsec "Ensure that the AAA server is reachable and enabled" "for accounting." CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED 4-Warning Transform [chars] not valid under IPSec transform [chars] Configured encryption algorithm not supported - "Specify a valid encryption algorithm for the ipsec transform" CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED 4-Warning Transform [chars] not valid under IPSec transform [chars] Configured encryption algorithm not supported - "Specify a valid encryption algorithm for the ipsec transform" CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_FULL_SPEED 4-Warning Transform [chars] will run with reduced performance because of IPSec transform [chars] Configured encryption algorithm will not run on the hardware encryption card. The transform is still usable but will run with reduced performance. - "If you need to use the full performance of the encryption card " "specify another encryption algorithm for the ipsec transform" CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_FULL_SPEED 4-Warning Transform [chars] will run with reduced performance because of IPSec transform [chars] Configured encryption algorithm will not run on the hardware encryption card. The transform is still usable but will run with reduced performance. - "If you need to use the full performance of the encryption card " "specify another encryption algorithm for the ipsec transform" CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_WITH_IKE 4-Warning Transform [chars] not usable with IKE because of IPSec transform [chars] Configured encryption algorithm not uable with IKE with current hardware configuration - "If you need to negotiate this with IKE specify a valid encryption " "algorithm for the ipsec transform" CRYPTO-4-IPSEC_ENC_METHOD_NOT_SUPPORTED_WITH_IKE 4-Warning Transform [chars] not usable with IKE because of IPSec transform [chars] Configured encryption algorithm not uable with IKE with current hardware configuration - "If you need to negotiate this with IKE specify a valid encryption " "algorithm for the ipsec transform" CRYPTO-4-ONTOKENKEYSDEACTIVATED 4-Warning On-Token RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now On-Token Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed pki "Re-insert the crypto token" CRYPTO-4-ONTOKENKEYSDEACTIVATED 4-Warning On-Token RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now On-Token Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed pki "Re-insert the crypto token" CRYPTO-4-PKT_REPLAY_ERR 4-Warning [chars]\n \tconnection id=[dec] sequence number=%lu\n Replay processing failed. This may be a temporary condition due to waiting for new SAs to be established. In the inbound case this may also be due to an actual replay attack. Some might consider this a hostile event. - "If the problem appears to be more than a transient one" " contact the peer's administrator." CRYPTO-4-PKT_REPLAY_ERR 4-Warning [chars]\n \tconnection id=[dec] sequence number=%lu\n Replay processing failed. This may be a temporary condition due to waiting for new SAs to be established. In the inbound case this may also be due to an actual replay attack. Some might consider this a hostile event. - "If the problem appears to be more than a transient one" " contact the peer's administrator." CRYPTO-4-RECVD_PKT_FAIL_DECOMPRESS 4-Warning pcp: [dec] byte packet failed to decompress pcp: dest_addr=[inet] src_addr=[inet] The received IPPCP packet failed to decompress. This may be due to a decompression buffer error. - LOG_STD_ACTION CRYPTO-4-RECVD_PKT_FAIL_DECOMPRESS 4-Warning pcp: [dec] byte packet failed to decompress pcp: dest_addr=[inet] src_addr=[inet] The received IPPCP packet failed to decompress. This may be due to a decompression buffer error. - LOG_STD_ACTION CRYPTO-4-RECVD_PKT_INV_CTCP_WRAPPER 4-Warning Rec'd packet has invalid cTCP wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec] Rec'd packet either cTCP encapsulated but is not correct negotiation transform. Or it expected an cTCP encapsulated packet but it received a non-cTCP packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_CTCP_WRAPPER 4-Warning Rec'd packet has invalid cTCP wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec] Rec'd packet either cTCP encapsulated but is not correct negotiation transform. Or it expected an cTCP encapsulated packet but it received a non-cTCP packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_IDENTITY 4-Warning [chars]\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n Decapsulated IPSEC packet not maching negotiated identity The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_IDENTITY 4-Warning [chars]\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n Decapsulated IPSEC packet not maching negotiated identity The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_IDENTITY_ACL 4-Warning ipsec check access: identity not allowed by ACL\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n After all is said and done the decaps packet fails the ACL check The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_IDENTITY_ACL 4-Warning ipsec check access: identity not allowed by ACL\n \tip dest_addr= [inet] src_addr= [inet] prot= [dec]\n After all is said and done the decaps packet fails the ACL check The peer is sending other traffic through this SA. It may be due to an SA selection error by the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_PROT 4-Warning decapsulate: packet missing [chars] destadr=[inet] actual prot=[dec] Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_INV_PROT 4-Warning decapsulate: packet missing [chars] destadr=[inet] actual prot=[dec] Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_INV_SPI 4-Warning decaps: rec'd IPSEC packet has invalid spi for destaddr=[chars] prot=[dec] spi=0x[hec][dec] srcaddr=[chars] Rec'd IPSEC packet specifies SPI that doesn't exist in SADB. This may be a temporary condition due to slight differences in aging of SAs between the IPSEC peers or it may be because the local SAs have been cleared. It may also be because of bogus packets sent by the IPSEC peer. Some might consider this a hostile event. - "If the local SAs have been cleared the peer may not know" " this. In this case if a new connection is established" " from the local router the two peers may reestablish " " successfully. Otherwise if the problem occurs for more than " " a brief period either attempt to establish a new connection " " or contact the peer's administrator." CRYPTO-4-RECVD_PKT_INV_SPI 4-Warning decaps: rec'd IPSEC packet has invalid spi for destaddr=[chars] prot=[dec] spi=0x[hec][dec] srcaddr=[chars] Rec'd IPSEC packet specifies SPI that doesn't exist in SADB. This may be a temporary condition due to slight differences in aging of SAs between the IPSEC peers or it may be because the local SAs have been cleared. It may also be because of bogus packets sent by the IPSEC peer. Some might consider this a hostile event. - "If the local SAs have been cleared the peer may not know" " this. In this case if a new connection is established" " from the local router the two peers may reestablish " " successfully. Otherwise if the problem occurs for more than " " a brief period either attempt to establish a new connection " " or contact the peer's administrator." CRYPTO-4-RECVD_PKT_INV_UDP_WRAPPER 4-Warning Rec'd packet has invalid udp wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec] Rec'd packet either udp encapsulated but is not correct negotiation transform. Or it expected an udp encapsulated packet but it received a non-udp packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_INV_UDP_WRAPPER 4-Warning Rec'd packet has invalid udp wrapper protocol.\n \tcryptoflags = [hec] sa->udp_wrapper_support = [dec] transform = [hec] Rec'd packet either udp encapsulated but is not correct negotiation transform. Or it expected an udp encapsulated packet but it received a non-udp packet. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_MAC_ERR 4-Warning decrypt: mac verify failed for connection id=[dec][chars] MAC verify processing failed. This may be due to the use of the wrong key by either party during the MAC calculations. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_MAC_ERR 4-Warning decrypt: mac verify failed for connection id=[dec][chars] MAC verify processing failed. This may be due to the use of the wrong key by either party during the MAC calculations. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_MSG_LEN_ERR 4-Warning decapsulate: packet has bad [chars] length destadr=[inet] prot=[dec] len=[dec] Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_MSG_LEN_ERR 4-Warning decapsulate: packet has bad [chars] length destadr=[inet] prot=[dec] len=[dec] Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event. - "Contact the peer's administrator." CRYPTO-4-RECVD_PKT_NOT_IPSEC 4-Warning Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[inet] src_addr= [inet] prot= [dec] Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated. IPSEC Peer is sending unencapsulated packets. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_NOT_IPSEC 4-Warning Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[inet] src_addr= [inet] prot= [dec] Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated. IPSEC Peer is sending unencapsulated packets. There may simply be a policy setup error on the peer. Some might consider this a hostile event. - "Contact the peer's administrator to compare policy settings." CRYPTO-4-RECVD_PKT_NOT_IPSEC_V6 4-Warning Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[chars] src_addr= [chars] prot= [dec] - - - CRYPTO-4-RECVD_PKT_NOT_IPSEC_V6 4-Warning Rec'd packet not an IPSEC packet. ip vrf/dest_addr= [chars]/[chars] src_addr= [chars] prot= [dec] - - - CRYPTO-4-REM_CRYPTOMAP_TS 4-Warning \nPlease recheck your crypto map [chars]. Transform set entry removed from crypto-map as it is no longer valid with hardware crypto engine enabled. - "Create and apply valid transform set to cryptomap" CRYPTO-4-REM_CRYPTOMAP_TS 4-Warning \nPlease recheck your crypto map [chars]. Transform set entry removed from crypto-map as it is no longer valid with hardware crypto engine enabled. - "Create and apply valid transform set to cryptomap" CRYPTO-4-TOKENKEYSDEACTIVATED 4-Warning RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed pki "Re-insert the crypto token" CRYPTO-4-TOKENKEYSDEACTIVATED 4-Warning RSA keypairs from token [chars] and associated IPSEC sessions being deactivated now Router RSA keypairs and associated IPSEC sessions are being deactivated because the token containing them was removed pki "Re-insert the crypto token" CRYPTO-4-TOKENKEYTIMEOUT 4-Warning RSA keypairs for token [chars] and associated IPSEC sessions will be deactivated in [dec] seconds Router RSA keypairs and associated IPSEC sessions will be deactivated when the timeout expires pki "Re-insert the crypto token before the timeout expires" CRYPTO-4-TOKENKEYTIMEOUT 4-Warning RSA keypairs for token [chars] and associated IPSEC sessions will be deactivated in [dec] seconds Router RSA keypairs and associated IPSEC sessions will be deactivated when the timeout expires pki "Re-insert the crypto token before the timeout expires" CRYPTO-4-TRANSFORM_NOT_SUPPORTED 4-Warning \nTransform [chars] is not supported with the current hardware configuration.\nGlobal transform [chars] will be deleted. System configuration modified.Some ipsec transforms which were earlier valid with software crypto are no longer valid now after switching hardware crypto. - "Create valid transform sets & update cryptomaps" CRYPTO-4-TRANSFORM_NOT_SUPPORTED 4-Warning \nTransform [chars] is not supported with the current hardware configuration.\nGlobal transform [chars] will be deleted. System configuration modified.Some ipsec transforms which were earlier valid with software crypto are no longer valid now after switching hardware crypto. - "Create valid transform sets & update cryptomaps" CRYPTO-5-GM_CONN_NEXT_SER 5-Notice GM is connecting to next key server from the list Connect to next key server ipsec-mcast LOG_STD_ACTION CRYPTO-5-GM_CONN_NEXT_SER 5-Notice GM is connecting to next key server from the list Connect to next key server ipsec-mcast LOG_STD_ACTION CRYPTO-5-GM_REGSTER 5-Notice Start registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars] Start registration for one group ipsec-mcast LOG_STD_ACTION CRYPTO-5-GM_REGSTER 5-Notice Start registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars] Start registration for one group ipsec-mcast LOG_STD_ACTION CRYPTO-5-IKE_SA_HA_STATUS 5-Notice IKE sa's if any for vip [inet] will change from [chars] to [chars] This is a notification message for crypto ike sa's changing their HA status ipsec-ha "No action is required" CRYPTO-5-IKE_SA_HA_STATUS 5-Notice IKE sa's if any for vip [inet] will change from [chars] to [chars] This is a notification message for crypto ike sa's changing their HA status ipsec-ha "No action is required" CRYPTO-5-IKEV2_SESSION_STATUS 5-Notice Crypto tunnel v2 is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars] This is a notification message for IPSEC tunnel status - "No action is required" CRYPTO-5-IKEV2_SESSION_STATUS 5-Notice Crypto tunnel v2 is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars] This is a notification message for IPSEC tunnel status - "No action is required" CRYPTO-5-IKMP_AG_MODE_DISABLED 5-Notice Unable to initiate or respond to Aggressive Mode while disabled The router is configured not to accept or respond to ISAKMP aggressive mode with any peer ipsec-isakmp "If you did not intend to disable aggressive-mode" " then remove the command" CRYPTO-5-IKMP_AG_MODE_DISABLED 5-Notice Unable to initiate or respond to Aggressive Mode while disabled The router is configured not to accept or respond to ISAKMP aggressive mode with any peer ipsec-isakmp "If you did not intend to disable aggressive-mode" " then remove the command" CRYPTO-5-IKMP_INVAL_CERT 5-Notice Certificate received from [chars] is bad: [chars] The certificate given by remote peer has either been revoked or expired certificate invalid or the signature check on the - "Contact the CA of the remote peer. Possibly bad CA certificate." CRYPTO-5-IKMP_INVAL_CERT 5-Notice Certificate received from [chars] is bad: [chars] The certificate given by remote peer has either been revoked or expired certificate invalid or the signature check on the - "Contact the CA of the remote peer. Possibly bad CA certificate." CRYPTO-5-IKMP_SETUP_FAILURE 5-Notice IKE SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld IKE Negotiation Failed. - "LOG_STD_ACTION" CRYPTO-5-IKMP_SETUP_FAILURE 5-Notice IKE SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld IKE Negotiation Failed. - "LOG_STD_ACTION" CRYPTO-5-IPSEC_FAILURE 5-Notice IPsec setup has failed local_ip: [chars] remote_ip: [chars] fail_reason: [chars] IPSEC Negotiation has failed - "LOG_STD_ACTION" CRYPTO-5-IPSEC_FAILURE 5-Notice IPsec setup has failed local_ip: [chars] remote_ip: [chars] fail_reason: [chars] IPSEC Negotiation has failed - "LOG_STD_ACTION" CRYPTO-5-IPSEC_SA_HA_STATUS 5-Notice IPSec sa's if any for vip [inet] will change from [chars] to [chars] This is a notification message for crypto ipsec sa's changing their HA status ipsec-ha "No action is required" CRYPTO-5-IPSEC_SA_HA_STATUS 5-Notice IPSec sa's if any for vip [inet] will change from [chars] to [chars] This is a notification message for crypto ipsec sa's changing their HA status ipsec-ha "No action is required" CRYPTO-5-IPSEC_SETUP_FAILURE 5-Notice IPSEC SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld IPSec Negotiation Failed. - "LOG_STD_ACTION" CRYPTO-5-IPSEC_SETUP_FAILURE 5-Notice IPSEC SETUP FAILED for local:[chars] local_id:[chars] remote:[chars] remote_id:[chars] IKE profile:[chars] fvrf:[chars] fail_reason:[chars] fail_class_cnt:%ld IPSec Negotiation Failed. - "LOG_STD_ACTION" CRYPTO-5-SELF_TEST_END 5-Notice Crypto algoritms self-test completed successfully\n\ All tests passed. The device has completed the Crypto algorithms self-tests.\n\ All of the self-tests have passed. - "Informational only. No action required." CRYPTO-5-SELF_TEST_END 5-Notice Crypto algoritms self-test completed successfully\n\ All tests passed. The device has completed the Crypto algorithms self-tests.\n\ All of the self-tests have passed. - "Informational only. No action required." CRYPTO-5-SESSION_STATUS 5-Notice Crypto tunnel is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars] - - - CRYPTO-5-SESSION_STATUS 5-Notice Crypto tunnel is [chars]. Peer [chars]:[dec] [chars] [chars] [chars] [chars] [chars] [chars] [chars] [chars] - - - CRYPTO-6-AUTOGEN 6-Information Generated new [dec] bit key pair Auto-Enroll has generated a new router key pair - "No action required. Informational message" CRYPTO-6-AUTOGEN 6-Information Generated new [dec] bit key pair Auto-Enroll has generated a new router key pair - "No action required. Informational message" CRYPTO-6-CET_END_OF_LIFE 6-Information CET connection msg in an IPSEC_ONLY_IMAGE CET has been End-of-lifed in IOS release 12.21 CSCds60123 "" CRYPTO-6-CET_END_OF_LIFE 6-Information CET connection msg in an IPSEC_ONLY_IMAGE CET has been End-of-lifed in IOS release 12.21 CSCds60123 "" CRYPTO-6-EZVPN_CONNECTION_DOWN 6-Information [chars] Ezvpn connection is being closed. The IPsec and IKE security associations will also be brought down along with it. - "" CRYPTO-6-EZVPN_CONNECTION_DOWN 6-Information [chars] Ezvpn connection is being closed. The IPsec and IKE security associations will also be brought down along with it. - "" CRYPTO-6-EZVPN_CONNECTION_UP 6-Information [chars] Ezvpn connection is up for the client mentioned. Both IPsec and IKE security Associations are up now. - "" CRYPTO-6-EZVPN_CONNECTION_UP 6-Information [chars] Ezvpn connection is up for the client mentioned. Both IPsec and IKE security Associations are up now. - "" CRYPTO-6-GDOI_ON_OFF 6-Information GDOI is [chars] The ISAKMP/gdoi process has been switched on or off either by CLI or because no GDOI crypto map or Key Server is applied to any interface. ipsec-getvpn "No action required." CRYPTO-6-GDOI_ON_OFF 6-Information GDOI is [chars] The ISAKMP/gdoi process has been switched on or off either by CLI or because no GDOI crypto map or Key Server is applied to any interface. ipsec-getvpn "No action required." CRYPTO-6-IKE_TED_BAD_REPLY 6-Information Received TED reply that did not correspond to a TED probe Rec'd TED reply that does not match a TED probe we currently have outstanding. This may be a one time occurance due to the TED reply being delayed. It may also be because of ill-formed packets sent by the peer. Some might consider this a hostile event. - "If the problem occurs more than once contact the peer's" " administrator." CRYPTO-6-IKE_TED_BAD_REPLY 6-Information Received TED reply that did not correspond to a TED probe Rec'd TED reply that does not match a TED probe we currently have outstanding. This may be a one time occurance due to the TED reply being delayed. It may also be because of ill-formed packets sent by the peer. Some might consider this a hostile event. - "If the problem occurs more than once contact the peer's" " administrator." CRYPTO-6-IKMP_ADD_KEY_FAIL 6-Information Unable to add public key for [chars] %15i to key ring Keys are stored in keyrings on the router. An attempt to add another key to the ring failed. - "Check local key rings. This is probably due to other failures." CRYPTO-6-IKMP_ADD_KEY_FAIL 6-Information Unable to add public key for [chars] %15i to key ring Keys are stored in keyrings on the router. An attempt to add another key to the ring failed. - "Check local key rings. This is probably due to other failures." CRYPTO-6-IKMP_AUTH_FAIL 6-Information Authentication method [dec] failed with host [chars] The IKE process was unable to authenticate its security Association with its remote peer. - "Contact the remote peer's administrator." CRYPTO-6-IKMP_AUTH_FAIL 6-Information Authentication method [dec] failed with host [chars] The IKE process was unable to authenticate its security Association with its remote peer. - "Contact the remote peer's administrator." CRYPTO-6-IKMP_BAD_CERT_USE 6-Information Certificate for peer at [chars] prohibits attempted use [chars]. X.509v3 certificates can contain usage restrictions. These can restrict use of the certificate only for signatures or only for key exchange encryption. The peer attempted to - "Contact the remote peer and the remote peer's CA" CRYPTO-6-IKMP_BAD_CERT_USE 6-Information Certificate for peer at [chars] prohibits attempted use [chars]. X.509v3 certificates can contain usage restrictions. These can restrict use of the certificate only for signatures or only for key exchange encryption. The peer attempted to - "Contact the remote peer and the remote peer's CA" CRYPTO-6-IKMP_BAD_DOI_NOTIFY 6-Information DOI of [dec] in notify message from [chars] The DOI field in notify messages give the receiver a context in which to understand the message being notified. This DOI value is not understood and the message therefore cannot be understood. - "If this situation persists contact the remote peer." CRYPTO-6-IKMP_BAD_DOI_NOTIFY 6-Information DOI of [dec] in notify message from [chars] The DOI field in notify messages give the receiver a context in which to understand the message being notified. This DOI value is not understood and the message therefore cannot be understood. - "If this situation persists contact the remote peer." CRYPTO-6-IKMP_BAD_DOI_SA 6-Information DOI value [dec] from SA offer from [chars] is invalid The DOI field of an SA offer defines how to parse the fields SAs with an unknown DOI cannot be parsed - "If this situation persists contact the remote peer's administrator" CRYPTO-6-IKMP_BAD_DOI_SA 6-Information DOI value [dec] from SA offer from [chars] is invalid The DOI field of an SA offer defines how to parse the fields SAs with an unknown DOI cannot be parsed - "If this situation persists contact the remote peer's administrator" CRYPTO-6-IKMP_CRYPT_FAILURE 6-Information IKE connection id [dec] unable to [chars] packet Encryption or decryption on a particular IKE thread failed. - "Contact remote peer" CRYPTO-6-IKMP_CRYPT_FAILURE 6-Information IKE connection id [dec] unable to [chars] packet Encryption or decryption on a particular IKE thread failed. - "Contact remote peer" CRYPTO-6-IKMP_MODE_FAILURE 6-Information Processing of [chars] mode failed with peer at [chars] Negotiation with the remote peer failed. - "If this situation persists contact the remote peer" CRYPTO-6-IKMP_MODE_FAILURE 6-Information Processing of [chars] mode failed with peer at [chars] Negotiation with the remote peer failed. - "If this situation persists contact the remote peer" CRYPTO-6-IKMP_NO_ID_CERT_ADDR_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate addr with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the ip address of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_ADDR_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate addr with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the ip address of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_DN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate DN with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the distinguished name of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_DN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate DN with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the distinguished name of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_FQDN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate fqdn with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the fqdn of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_FQDN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate fqdn with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the fqdn of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_USER_FQDN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate user fqdn with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the user fqdn of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NO_ID_CERT_USER_FQDN_MATCH 6-Information NOT ERROR BUT WARNING ONLYID of [chars] type [dec] and certificate user fqdn with [chars] ISAKMP entities assume an identity to inform the peer of who or what they are. The claimed identity did not match the information gleaned from the user fqdn of the peer's certificate. - "Contact the remote peer if this situation persists" CRYPTO-6-IKMP_NOT_ENCRYPTED 6-Information IKE packet from [chars] was not encrypted and it should've been. A portion of the IKE exchange takes place in the clear and a portion is encrypted. This message should have been encrypted but was not. - "Contact remote peer" CRYPTO-6-IKMP_NOT_ENCRYPTED 6-Information IKE packet from [chars] was not encrypted and it should've been. A portion of the IKE exchange takes place in the clear and a portion is encrypted. This message should have been encrypted but was not. - "Contact remote peer" CRYPTO-6-IKMP_POLICY_DEFAULT 6-Information Using ISAKMP Default policies Since the user has not configured any ISAKMP policies and default ISAKMP policies are enabled then use default ISAKMP policies for negotiation - "" CRYPTO-6-IKMP_POLICY_DEFAULT 6-Information Using ISAKMP Default policies Since the user has not configured any ISAKMP policies and default ISAKMP policies are enabled then use default ISAKMP policies for negotiation - "" CRYPTO-6-IKMP_SA_NOT_AUTH 6-Information Cannot accept Quick Mode exchange from [chars] if SA is not authenticated! The IKE security association with the remote peer was not authenticated yet the peer attempted to begin a Quick Mode exchange. This exchange must only be done with an authenticated security association - "Contact remote peer" CRYPTO-6-IKMP_SA_NOT_AUTH 6-Information Cannot accept Quick Mode exchange from [chars] if SA is not authenticated! The IKE security association with the remote peer was not authenticated yet the peer attempted to begin a Quick Mode exchange. This exchange must only be done with an authenticated security association - "Contact remote peer" CRYPTO-6-IKMP_SA_NOT_OFFERED 6-Information Remote peer [chars] responded with attribute [chars] not offered or changed IKE peers negotiate policy by the initiator offering a list of possible alternate protection suites. The responder responded with one that the initiator did not offer - "Contact the remote peer" CRYPTO-6-IKMP_SA_NOT_OFFERED 6-Information Remote peer [chars] responded with attribute [chars] not offered or changed IKE peers negotiate policy by the initiator offering a list of possible alternate protection suites. The responder responded with one that the initiator did not offer - "Contact the remote peer" CRYPTO-6-IKMP_UNK_EXCHANGE 6-Information IKE peer at [chars] sent a message with unknown exchange [dec] IKE preforms actions on messages based on defined exchanges. The message received had an unknown exchange. - "Contact the remote peer's administrator" CRYPTO-6-IKMP_UNK_EXCHANGE 6-Information IKE peer at [chars] sent a message with unknown exchange [dec] IKE preforms actions on messages based on defined exchanges. The message received had an unknown exchange. - "Contact the remote peer's administrator" CRYPTO-6-IPSEC_USING_DEFAULT 6-Information IPSec is using default transforms No IPSec transform-set defined and default policy is enabled. Therefore default policies are being proposed to the peer ipsec-core "To avoid using IPSec default policy" "reconfigure a transform set to be used for " "this crypto session" CRYPTO-6-IPSEC_USING_DEFAULT 6-Information IPSec is using default transforms No IPSec transform-set defined and default policy is enabled. Therefore default policies are being proposed to the peer ipsec-core "To avoid using IPSec default policy" "reconfigure a transform set to be used for " "this crypto session" CRYPTO-6-ISAKMP_MANUAL_DELETE 6-Information IKE SA manually deleted. Do 'clear crypto sa peer [chars]' to manually clear IPSec SA's covered by this IKE SA. The IKE SA was deleted by user command. However keepalives this connection are enabled and IPSec SA's covered by this IKE SA still exist. Since this IKE SA is now deleted these IPSec SA's have no IKE SA covering them. The recommended action is to manually delete this IPSec SA's. ipsec "Use parser command "clear crypto sa" to clear " "IPSec SA's." CRYPTO-6-ISAKMP_MANUAL_DELETE 6-Information IKE SA manually deleted. Do 'clear crypto sa peer [chars]' to manually clear IPSec SA's covered by this IKE SA. The IKE SA was deleted by user command. However keepalives this connection are enabled and IPSec SA's covered by this IKE SA still exist. Since this IKE SA is now deleted these IPSec SA's have no IKE SA covering them. The recommended action is to manually delete this IPSec SA's. ipsec "Use parser command "clear crypto sa" to clear " "IPSec SA's." CRYPTO-6-ISAKMP_ON_OFF 6-Information ISAKMP is [chars] The ISAKMP process has been switched on or off either by CLI or because no crypto map or EzVPN configuration is applied to any interface. ipsec-isakmp "No action required." CRYPTO-6-ISAKMP_ON_OFF 6-Information ISAKMP is [chars] The ISAKMP process has been switched on or off either by CLI or because no crypto map or EzVPN configuration is applied to any interface. ipsec-isakmp "No action required." CRYPTO-6-LLQ_OVERSUBSCRIBE 6-Information Sum of priority class bandwidth exceeds crypto engine's throughput for small packets crypto b/w=[dec] kbps allocated b/w=[dec] kbps. The crypto engine may be oversubscribed by priority class traffic. This happens when the user tries to provision more priority class bandwidth than what the crypto engine can handle. If each class is sending at its max rate some priority packets may be dropped - "Reduce the priority class bandwidth or reduce" "the number of priority classes in the policy-map" CRYPTO-6-LLQ_OVERSUBSCRIBE 6-Information Sum of priority class bandwidth exceeds crypto engine's throughput for small packets crypto b/w=[dec] kbps allocated b/w=[dec] kbps. The crypto engine may be oversubscribed by priority class traffic. This happens when the user tries to provision more priority class bandwidth than what the crypto engine can handle. If each class is sending at its max rate some priority packets may be dropped - "Reduce the priority class bandwidth or reduce" "the number of priority classes in the policy-map" CRYPTO-6-PRINTABORT 6-Information [chars] caused early termination of show output[chars] While showing a list the list was changed or elements changed. This can happen if SA's are re-negotiated at the time the show-command was paused or if someone reconfigured or cleared SA's amongst other things. This is not an error but a side-effect of a dynamic system. ipsec "In general this is merely a warning that the " "output from the show command is most likely incomplete. " "Re-running the show-command should provide the newest " "information. On a busy system with ever-changing SA's " "this may appear frequently." CRYPTO-6-PRINTABORT 6-Information [chars] caused early termination of show output[chars] While showing a list the list was changed or elements changed. This can happen if SA's are re-negotiated at the time the show-command was paused or if someone reconfigured or cleared SA's amongst other things. This is not an error but a side-effect of a dynamic system. ipsec "In general this is merely a warning that the " "output from the show command is most likely incomplete. " "Re-running the show-command should provide the newest " "information. On a busy system with ever-changing SA's " "this may appear frequently." CRYPTO-6-PRNG_SEED_KEY_ERROR 6-Information Pseudo-random number generator seed and seed key was identical The X9.17 random number specification requires us to check for\n\ the same value appearing as the seed and the seed key. This\n\ message indicates that the condition was discovered. ipsec "The X9.17 random number will occasionally produce this condition\n\ and this is not a problem. However if this message occurs frequently\n\ the system should be manually reloaded. If the message is persistent\n\ across reloads copy the error message exactly as it appears and\n\ report it to your technical support representative." CRYPTO-6-PRNG_SEED_KEY_ERROR 6-Information Pseudo-random number generator seed and seed key was identical The X9.17 random number specification requires us to check for\n\ the same value appearing as the seed and the seed key. This\n\ message indicates that the condition was discovered. ipsec "The X9.17 random number will occasionally produce this condition\n\ and this is not a problem. However if this message occurs frequently\n\ the system should be manually reloaded. If the message is persistent\n\ across reloads copy the error message exactly as it appears and\n\ report it to your technical support representative." CRYPTO-6-RANDOM 6-Information A pseudo-random number was generated twice in succession by [chars] A pseudo-random number generator produced the same number twice\n\ in succession. ipsec "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." CRYPTO-6-RANDOM 6-Information A pseudo-random number was generated twice in succession by [chars] A pseudo-random number generator produced the same number twice\n\ in succession. ipsec "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." CRYPTO-6-SELF_TEST_RESULT 6-Information Self test info: [chars] This audit prompt the results of Cryptographical selftests - "This message is for information only. No action is" " required." CRYPTO-6-SELF_TEST_RESULT 6-Information Self test info: [chars] This audit prompt the results of Cryptographical selftests - "This message is for information only. No action is" " required." CRYPTO-6-TOKENADMINCHANGEPIN 6-Information Cryptographic Token [chars] ADMIN PIN change Successful The cryptographic token has accepted the new administrator PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENADMINCHANGEPIN 6-Information Cryptographic Token [chars] ADMIN PIN change Successful The cryptographic token has accepted the new administrator PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENADMINLOGIN 6-Information Cryptographic Token [chars] ADMIN Login Successful The cryptographic token has accepted the administrator PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENADMINLOGIN 6-Information Cryptographic Token [chars] ADMIN Login Successful The cryptographic token has accepted the administrator PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENCHANGEPIN 6-Information Cryptographic Token [chars] PIN change Successful The cryptographic token has accepted the new PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENCHANGEPIN 6-Information Cryptographic Token [chars] PIN change Successful The cryptographic token has accepted the new PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENINSERTED 6-Information Cryptographic token [chars] inserted in [chars] A cryptographic token has been detected - "Informational message only. No action required." CRYPTO-6-TOKENINSERTED 6-Information Cryptographic token [chars] inserted in [chars] A cryptographic token has been detected - "Informational message only. No action required." CRYPTO-6-TOKENLOGIN 6-Information Cryptographic Token [chars] Login Successful The cryptographic token has accepted the PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENLOGIN 6-Information Cryptographic Token [chars] Login Successful The cryptographic token has accepted the PIN offered by the router - "Informational message only. No action required." CRYPTO-6-TOKENLOGOUT 6-Information Cryptographic Token [chars] Logout Successful The router has logged out from the cryptographic token - "Informational message only. No action required." CRYPTO-6-TOKENLOGOUT 6-Information Cryptographic Token [chars] Logout Successful The router has logged out from the cryptographic token - "Informational message only. No action required." CRYPTO-6-TOKENREMOVED 6-Information Cryptographic token [chars] removed from [chars] A cryptographic token has been detected - "Informational message only. No action required." CRYPTO-6-TOKENREMOVED 6-Information Cryptographic token [chars] removed from [chars] A cryptographic token has been detected - "Informational message only. No action required." CRYPTO-6-TOKENSTOREKEY 6-Information Key [chars] stored on Cryptographic Token [chars] Successfully A new keypair has been written out to the cryptographic token - "Informational message only. No action required." CRYPTO-6-TOKENSTOREKEY 6-Information Key [chars] stored on Cryptographic Token [chars] Successfully A new keypair has been written out to the cryptographic token - "Informational message only. No action required." CRYPTO-6-TOKENTIMEOUTCANCELLED 6-Information Cryptographic Token [chars] re-inserted. removal timeout cancelled A cryptographic token containing private key files has been re-inserted in time. Router RSA keypairs and associated IPSEC sessions will be NOT be deactivated - "Informational message only. No action required." CRYPTO-6-TOKENTIMEOUTCANCELLED 6-Information Cryptographic Token [chars] re-inserted. removal timeout cancelled A cryptographic token containing private key files has been re-inserted in time. Router RSA keypairs and associated IPSEC sessions will be NOT be deactivated - "Informational message only. No action required." CRYPTO-6-VPN_TUNNEL_STATUS 6-Information [chars] VPN tunnel status. - "" CRYPTO-6-VPN_TUNNEL_STATUS 6-Information [chars] VPN tunnel status. - "" CSG-3-ERROR 3-Error Module [dec]: [chars] An error occurred in a CSG module. csg LOG_STD_RECUR_ACTION CSG-3-RELOADNOTOK 3-Error CSG ACCOUNTING [chars] reload on module [dec] failed. Informational message whenever a CSG configuration\n\ is reloaded as a result of power recycling a CSG card. csg LOG_STD_NO_ACTION CSG-4-WARNING 4-Warning Module [dec]: [chars] Some possibly undesired event occurred in a CSG module. csg LOG_STD_RECUR_ACTION CSG-6-LIRELOADOK 6-Information CSG LI reload on module [dec] successful Informational message whenever a CSG LI configuration\n\ is reloaded as a result of power recycling a CSG card. csg LOG_STD_NO_ACTION CSG-6-RELOADOK 6-Information CSG ACCOUNTING [chars] reload on module [dec] successful Informational message whenever a CSG configuration\n\ is reloaded as a result of power recycling a CSG card. csg LOG_STD_NO_ACTION CSM_SLB-3-ERROR 3-Error Module [dec] error: [chars] An error occurred in a CSM-SLB module. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-IDB_ERROR 3-Error Unknown error occurred while configuring IDB for CSM-SLB module: [chars]. Unable to configure data path for CSM-SLB card. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-OUTOFMEM 3-Error Module [dec] memory error: [chars] Out of memory condition while downloading SLB configurations onto CSM card. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-PORTCHANNEL 3-Error Portchannel allocation failed for module [dec]. Unable to allocate enough portchannel groups for CSM-SLB card. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-REDUNDANCY 3-Error Module [dec] FT error: [chars] An error occurred in CSM-SLB fault tolerance. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-RELOAD 3-Error Module [dec] configuration reload failed: [chars] Configuration reload of the CSM-SLB card failed. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-SCRIPT 3-Error Module [dec] script error: [chars] An error occurred in a CSM-SLB script. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-UNEXPECTED 3-Error Module [dec] unexpected error: [chars] An unexpected error condition occurred on the CSM-SLB card while performing Server Load Balancing. laminar LOG_STD_RECUR_ACTION CSM_SLB-3-VERMISMATCH 3-Error Module [dec] image version mismatch RP = [chars] CSM = [chars]: [chars] Router image and CSM-SLB image do not correspond. laminar LOG_STD_RECUR_ACTION CSM_SLB-4-ARPCONFIG 4-Warning Module [dec] ARP configuration error: [chars] Error creating or removing a static ARP route. laminar LOG_STD_RECUR_ACTION CSM_SLB-4-DUPLICATEID 4-Warning Module [dec] duplicate ID: [chars] Same ID was used to create multiple entities. laminar LOG_STD_NO_ACTION CSM_SLB-4-ERRPARSING 4-Warning Module [dec] configuration warning: [chars] Syntax error in a URL or COOKIE regular expression in SLB configuration. laminar LOG_STD_NO_ACTION CSM_SLB-4-INVALIDID 4-Warning Module [dec] invalid ID: [chars] The entity identified does not exist. laminar LOG_STD_NO_ACTION CSM_SLB-4-PROBECONFIG 4-Warning Module [dec] probe configuration error: [chars] Health probe configuration failed. laminar LOG_STD_NO_ACTION CSM_SLB-4-REDUNDANCY_WARN 4-Warning Module [dec] FT warning: [chars] Some possibly undesired event occurred in CSM-SLB fault tolerance. laminar LOG_STD_RECUR_ACTION CSM_SLB-4-REGEXMEM 4-Warning Module [dec] regular expression memory error: [chars] A lookup table does not contain enough space to store the configured URL and COOKIE regular expressions. Use 'show ip slb memory' to determine which virtual servers were unable to be configured because of laminar LOG_STD_NO_ACTION CSM_SLB-4-SCRIPT_WARN 4-Warning Module [dec] script warning: [chars] Some possibly undesired event occurred in CSM-SLB scripting. laminar LOG_STD_RECUR_ACTION CSM_SLB-4-TOPOLOGY 4-Warning Module [dec] warning: [chars] There may be a problem with your network topology or configuration. laminar LOG_STD_RECUR_ACTION CSM_SLB-4-VERWILDCARD 4-Warning Received CSM-SLB module version wildcard on slot [dec]. Supervisor has version [dec]. User issued a command from the linecard to bypass the safeguard against module version mismatch. As a result configuration may fail. laminar LOG_STD_NO_ACTION CSM_SLB-4-WARNING 4-Warning Module [dec] warning: [chars] Some possibly undesired event occurred in a CSM-SLB module. laminar LOG_STD_RECUR_ACTION CSM_SLB-6-GATEWAYSTATE 6-Information Module [dec] gateway state changed: [chars] A gateway changed states. laminar LOG_STD_NO_ACTION CSM_SLB-6-INFO 6-Information Module [dec] info: [chars] Some event occurred in a CSM-SLB module. laminar LOG_STD_NO_ACTION CSM_SLB-6-REDUNDANCY_INFO 6-Information Module [dec] FT info: [chars] Some event occurred in CSM-SLB fault tolerance. laminar LOG_STD_NO_ACTION CSM_SLB-6-RSERVERSTATE 6-Information Module [dec] server state changed: [chars] A real server changed states failed or recovered. Possible causes might be configuration changes arp checks or health probes. laminar LOG_STD_NO_ACTION CSM_SLB-6-SCRIPT_INFO 6-Information Module [dec] script info: [chars] Some event occurred in CSM-SLB scripting. laminar LOG_STD_NO_ACTION CSM_VOICE-3-ADDINTRFFAIL 3-Error The Voice Telephony Service Provider has rejected our\n\ request to add this voice interface [dec]:[dec] The voice software was unable to report a new signaling\n\ interface to the Voice Telephony Service Provider as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-ADDINTRFFAIL 3-Error The Voice Telephony Service Provider has rejected our\n\ request to add this voice interface [dec]/[dec]:[dec] The voice software was unable to report a new signaling\n\ interface to the Voice Telephony Service Provider das LOG_STD_SH_TECH_ACTION CSM_VOICE-3-MALLOC 3-Error No memory is available to build any internal data \n\ structure for the voice software. The voice software was unable allocate memory to build \n\ any internal data structures. The system may be \n\ out of memory. as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-MALLOC 3-Error No memory is available to build any internal data \n\ structure for the voice software. The voice software was unable allocate memory to build \n\ any internal data structures. The system may be \n\ out of memory. das LOG_STD_SH_TECH_ACTION CSM_VOICE-3-NOMEM 3-Error No memory is available to build the voice interface [dec]:[dec] The voice software was unable allocate memory to build \n\ a voice interface data structure. The system may be \n\ out of memory. as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-NOMEM 3-Error No memory is available to build the voice interface [dec]:[dec] The voice software was unable allocate memory to build \n\ a voice interface data structure. The system may be \n\ out of memory. das LOG_STD_SH_TECH_ACTION CSM_VOICE-3-NOSDB 3-Error No signaling data block is available to build the \n\ voice interface[dec]:[dec] The voice software was unable to obtain a signaling data\n\ block from the Voice Telephony Service Provider. \n\ The system may be out of memory. as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-NOSDB 3-Error No signaling data block is available to build the \n\ voice interface[dec]/[dec]:[dec] The voice software was unable to obtain a signaling data\n\ block from the Voice Telephony Service Provider. \n\ The system may be out of memory. das LOG_STD_SH_TECH_ACTION CSM_VOICE-3-NOTDMCHNL 3-Error CSM failed to get a free dsp tdm channel from the DSP\n\ Resource Manager DSPRM to handle an incoming call The voice software was unable to obtain the tdm channel \n\ for a free dsp from the DSP Resource Manager. All of \n\ the dsp's have been used to process calls or have\n\ been taken out of service. as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-TDMHPMADDFAIL 3-Error CSM failed to add the CAS TDM hairpinning call The CSM voice software interface was unable to add\n\ this call as hairpinning because of presence of\n\ another call for the same DS0. Internal software error. as LOG_STD_SH_TECH_ACTION CSM_VOICE-3-UNDEFDSX0 3-Error Undefined dsx0 interface for controller[dec] The dsx0 interface for the specified controller\n\ is not defined but the voice software use it. as "Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls." CSM_VOICE-3-UNDEFDSX0 3-Error Undefined dsx0 interface for controller[dec]/[dec] The dsx0 interface for the specified controller\n\ is not defined but the voice software use it. das "Internal software fault. Contact your field service representative \n\ if this message is coincident with dropped calls." CSM_VOICE-3-UNDEFVOICEINTRF 3-Error Invalid voice interface controller:group[dec]:[dec] The voice interface defined by controller:group is not\n\ yet defined within the voice software but attempts were\n\ made to use this interface. as "Internal software fault. Contact your field service \n\ representative if this message is coincident with \n\ dropped calls." CSM_VOICE-3-UNDEFVOICEINTRF 3-Error Invalid interface slot:controller:group[dec]/[dec]:[dec] The voice interface defined by slot:controller:group is not\n\ yet defined within the voice software but attempts were\n\ made to use this interface. das "Internal software fault. Contact your field service \n\ representative if this message is coincident with \n\ dropped calls." CSM-1-CAS_ALLOC_FAIL 1-Alert Fail to add new signal channel [dec]/[dec] timeslot [dec] - - "" CSM-1-CSM_CALL_INFO_MISMATCH 1-Alert csm_call_info contains\n\ mismatch information call info has [chars]:[dec] framer gives [dec]/[dec]:[dec] - - "" CSM-1-CSM_CALL_NO_RESOURCE 1-Alert Failed to allocate resource for call from [dec]/[dec]:[dec] - - "" CSM-1-CSM_STRING_OVERRUN 1-Alert String copy exceeded buffer size The string written into the allocated buffer exceeded the size of\n\ the buffer. This can cause memory corruption. - LOG_STD_ACTION CSM-1-DCHAN_ALLOC_FAIL 1-Alert For channel [chars] - - "" CSM-1-HWIDB 1-Alert [chars]: hwidb is NULL An internal software error occurred. as LOG_STD_ACTION CSM-1-HWIDB_SUBBLOCK 1-Alert [chars]: hwidb subblock for b channel [dec] is in use An internal software error occurred. as LOG_STD_ACTION CSM-1-INITFAIL 1-Alert [chars] - - "" CSM-1-INITPORTFAIL 1-Alert Initialization of vdev [dec]/[dec]/[dec] failed - - "" CSM-1-INITSYS 1-Alert [chars] Failed to create a periodic process for CSM or the number of\n\ digit collectors reported to CSM exceeds the maximum number of\n\ digit collectors. as LOG_STD_ACTION CSM-1-INVALID_DC_NUMBER 1-Alert Initialization failed with invalid digit collector count - - "" CSM-1-MODEM_INFO 1-Alert [chars]: modem_info is NULL An internal software error occurred. - LOG_STD_ACTION CSM-1-NEW_RBS_CHAN 1-Alert A new RBS channel added - - "" CSM-1-NO_CSM_CALL_INFO 1-Alert No call control block - - "" CSM-1-NO_HWIDB 1-Alert No B channel associated with call - - "" CSM-1-RBS 1-Alert [chars] at slot [dec] controller [dec] timeslot [dec] This is an internal software error. An attempt is made to add non\n\ existent CAS signalling interface. as LOG_STD_ACTION CSM-3-NO_VDEV 3-Error No modems associated:[chars]Chan[dec]Id[dec] - - "" CSM-5-PRI 5-Notice [chars] at slot [dec] unit [dec] channel [dec] with index [dec] A PRI signalling channel is added/deleted to CSM's inventory\n\ of signalling channels. as "This is a notification message only.\n\ No action is required." CSMPI-3- ADDR_MISMATCH 3-Error Region address error: start @ %p end @ %p part addr @ %p CSMPI encountered a bnad buffer address possible corruption. - LOG_STD_ACTION CSMPI-3- BAD_INDEX 3-Error bad particle index [dec] max [dec] addr %p CSMPI encountered a bnad buffer address possible corruption. - LOG_STD_ACTION CSMPI-3- IF_INIT_FAILED 3-Error CSMPI interface initialization failed. Essential CSMPI initialization has failed. - LOG_STD_ACTION CSMPI-3- PLATFORM_INIT_FAILED 3-Error CSMPI platform initialization failed. Essential CSMPI initialization has failed. - LOG_STD_ACTION CTLPROVIDERSERV-3-NOINIT 3-Error Can't initialize Credentials server Internal problems with initializing ports for the Credentials server ios-callmgr "Make sure the Credentials server port is available on the local machine." CTLPROVIDERSERV-3-NOINIT 3-Error Can't initialize Credentials server Internal problems with initializing ports for the Credentials server ios-callmgr "Make sure the Credentials server port is available on the local machine." CTLPROVIDERSERV-3-NOMEM 3-Error Can't initialize memory for Credentials server Insufficient Memory for Credentials server ios-callmgr "Increase amount of available memory" CTLPROVIDERSERV-3-NOMEM 3-Error Can't initialize memory for Credentials server Insufficient Memory for Credentials server ios-callmgr "Increase amount of available memory" CTLPROVIDERSERV-3-NOPROC 3-Error Could not start Credentials Server Internal Problem in process creation ios-callmgr "None" CTLPROVIDERSERV-3-NOPROC 3-Error Could not start Credentials Server Internal Problem in process creation ios-callmgr "None" CTLPROVIDERSERV-3-NOSOCKETS 3-Error Max Number of Credentials Server sockets exceeded There are too many Credentials clients requesting service ios-callmgr "Reduce number of Credentials requesting service" CTLPROVIDERSERV-3-NOSOCKETS 3-Error Max Number of Credentials Server sockets exceeded There are too many Credentials clients requesting service ios-callmgr "Reduce number of Credentials requesting service" CTOKEN-3-INITFAIL 3-Error Initialization of Consent Token facility failed [chars]. An unexpected condition has occurred which resulted in Consent Token facility failing to start. This is a serious problem and means that Consent Token facility will not be functional. iosxe-ct-lib LOG_STD_ACTION CTOKEN-3-REQPROCFAIL 3-Error Consent Token Request Processing facility failed [chars]. An unexpected condition has occurred which resulted in Consent Token facility failing to process a request. This means that some part of Consent Token facility will not be functional. iosxe-ct-lib LOG_STD_ACTION CTOKEN-6-AUTH_UPDATE 6-Information Consent Token Update [chars]. Consent Token authentication state change update iosxe-ct-lib LOG_STD_NO_ACTION CTRC-3-APPCERROR 3-Error [chars] An APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server. ctrc "This usually indicates a problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared." CTRC-3-APPCVERB 3-Error Unexpected APPC error: opcode %04x primary code %04x secondary code %08lx An unexpected APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server. Opcode\n\ identifies the APPC API call that received the error. Primary and\n\ secondary return codes are returned by the APPC API. ctrc "This usually indicates a problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared." CTRC-3-NOBUFFS 3-Error No buffers available to [chars] CTRC attempted to allocate a buffer while performing the \n\ operation described in the message text. A buffer pool does \n\ not contain enough items to satisfy the allocation request. ctrc "This problem most commonly occurs whenever a public buffer \n\ pool runs out of elements. Determine the which pool has run\n\ out of buffers using the \"show buffers\" command. Adjust the\n\ pool size using the buffers configuration command." CTRC-3-SNASWNOTSTARTED 3-Error SNASW is not started -- unable to connect to remote database. A client connected to a ctrc server but ctrc was unable to\n\ connect out to the remote database because SNASW is not started.\n\ ctrc uses SNASW to connect to the remote database server. You\n\ must start SNASW before ctrc clients attempt to connect. ctrc "Start SNASW and retry the client connection." CTRC-3-SNASWSTOPPED 3-Error SNASW was stopped -- existing connections have been closed. SNASW was stopped while ctrc connections were open. Stopping\n\ SNASW caused all open SNA connections to the remote database\n\ server to be lost. As a result all client connections were\n\ disconnected. You should not stop SNASW while there are open\n\ ctrc connections. ctrc "Restart SNASW. Disconnected clients must reconnect." CTRC-4-APPCWARN 4-Warning [chars] An APPC error occurred. ctrc uses APPC API calls to\n\ SNASW to communicate with the remote database server. ctrc "This usually indicates a temporary problem in the SNA network. Try the ctrc\n\ ping command to test connectivity to the remote database server. If\n\ the ctrc ping fails check the status of the SNA link to the\n\ remote database server with the show snasw link command. If the link\n\ is active try stopping and starting the link. If the problem persists\n\ contact your SNA network administrator for help in troubleshooting. " LOG_STD_RECUR_ACTION " If possible also provide the output of the debug ctrc appc\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared." CTS_PD-2-IPC_FAILURE 2-Critical CTS-IPC message [chars] handler failed rc [dec] An IPC message handler for the CTS feature failed. This will cause the feature to not function. asr1k-cts LOG_STD_ACTION CTS_PD-3-FEAT_CTX_DOWN 3-Error CTS-Invalid request [chars] [dec] while context is down While the feature context was not active an invalid request was received from another layer of the CTS software stack. asr1k-cts LOG_STD_RECUR_ACTION CTS_PD-3-FEAT_DOWN 3-Error CTS-Invalid request [chars] [dec] while feature is down While the feature was not active an invalid request was received from another layer of the CTS software stack. asr1k-cts LOG_STD_RECUR_ACTION CTS_PD-3-IPC_INIT_FAILED 3-Error CTS-IPC message handler registration failure rc [dec] Registering an IPC message handler for the CTS feature failed. This will cause the feature to not function. asr1k-cts LOG_STD_ACTION CTS_PD-3-IPC_INVALID_MSG 3-Error CTS-Invalid request [dec] We received an invalid message from another layer of the CTS software stack. asr1k-cts LOG_STD_RECUR_ACTION CTS_PD-3-IPC_INVALID_MSG_LEN 3-Error CTS-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length asr1k-cts LOG_STD_ACTION CTS_PD-3-IPC_NORES 3-Error CTS-No space for the IPC reply size [dec] request [dec] For a request from upper CTS software stack layers it was not possible to allocate space for a reply for the specified size. asr1k-cts LOG_STD_RECUR_ACTION CTS_PD-3-IPC_OPEN_REPLY 3-Error CTS-IPC Open Reply failed request [dec] For a request from upper CTS software stack layers it was not possible to open the reply buffer. asr1k-cts "This is normally a software issue. " LOG_STD_RECUR_ACTION CTS_PD-3-IPC_SEND_FAILED 3-Error CTS-IPC [chars] [dec] send failed [dec] IPC message send failure asr1k-cts LOG_STD_ACTION CTS-0-AUTHZ_OUT_OF_MEM 0-Emergency [chars] failed to create [chars] due to insufficient memory The system is experiencing insufficent memory. - LOG_STD_ACTION CTS-0-AUTHZ_OUT_OF_MEM 0-Emergency [chars] failed to create [chars] due to insufficient memory The system is experiencing insufficent memory. - LOG_STD_ACTION CTS-0-AUTHZ_OUT_OF_MEM 0-Emergency [chars] failed to create [chars] due to insufficient memory The system is experiencing insufficent memory. - LOG_STD_ACTION CTS-0-CTS_EMERG 0-Emergency [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-0-CTS_EMERG 0-Emergency [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-0-IFC_OUT_OF_MEM 0-Emergency [chars] failed to create [chars] due to insufficient memory The system is experiencing insufficent memory. - LOG_STD_ACTION CTS-0-IFC_OUT_OF_MEM 0-Emergency [chars] failed to create [chars] due to insufficient memory The system is experiencing insufficent memory. - LOG_STD_ACTION CTS-1-CTS_ALERT 1-Alert [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-1-CTS_ALERT 1-Alert [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-1-CTS_CRED_ACTION_NEEDED 1-Alert CTS credentials are missing or inconsistent in the redundant keystore.\n Please re-configure cts credentials or execute cts change-password. A redundant keystore was detected as either not containing any CTS credentials or having a different set of credentials as contained in the active keystore. This means that CTS authentication will fail upon switchover unless remedial action is taken before then. Either use the \cts credentials ...\ CLI to re-configure the CTS device-id and password or use the \cts change-password ...\ CLI to initiate a password change with the AAA server. Either of these actions will cause the device-id and password to be inserted in both the active and redundant keystores. - - CTS-1-CTS_CRED_ACTION_NEEDED 1-Alert CTS credentials are missing or inconsistent in the redundant keystore.\n Please re-configure cts credentials or execute cts change-password. A redundant keystore was detected as either not containing any CTS credentials or having a different set of credentials as contained in the active keystore. This means that CTS authentication will fail upon switchover unless remedial action is taken before then. Either use the \cts credentials ...\ CLI to re-configure the CTS device-id and password or use the \cts change-password ...\ CLI to initiate a password change with the AAA server. Either of these actions will cause the device-id and password to be inserted in both the active and redundant keystores. - - CTS-1-CTS_CRED_ACTION_NEEDED 1-Alert CTS credentials are missing or inconsistent in the redundant keystore.\n Please re-configure cts credentials or execute cts change-password. A redundant keystore was detected as either not containing any CTS credentials or having a different set of credentials as contained in the active keystore. This means that CTS authentication will fail upon switchover unless remedial action is taken before then. Either use the \cts credentials ...\ CLI to re-configure the CTS device-id and password or use the \cts change-password ...\ CLI to initiate a password change with the AAA server. Either of these actions will cause the device-id and password to be inserted in both the active and redundant keystores. - - CTS-1-SXP_BINDING_EXP 1-Alert Binding [chars]<[chars] [chars]> can't be expanded. Expanded [dec] and maximum allowed is [dec]\n Binding propagated in the network is not consistent. SXP expasion exceed maximum allowed.\n Binding propagated in the network is not consistent.\n User should remove the subnet binding. CTS_DDTS_COMPONENT "Remove this subnet if possible" CTS-1-SXP_BINDING_EXP 1-Alert Binding [chars]<[chars] [chars]> can't be expanded. Expanded [dec] and maximum allowed is [dec]\n Binding propagated in the network is not consistent. SXP expasion exceed maximum allowed.\n Binding propagated in the network is not consistent.\n User should remove the subnet binding. CTS_DDTS_COMPONENT "Remove this subnet if possible" CTS-2-AUTHZ_POLICY_SGACL_ACE_FAILED 2-Critical Failed to [chars][chars] SGACL '[chars]' for SGT=[chars] due to ACE '[chars]' error. Download will be retried in 60 seconds An error occurred in the ACE while CTS attempted to acquire SGACL policy from the policy server. Retry will be attempted in 60 seconds - LOG_STD_ACTION CTS-2-AUTHZ_POLICY_SGACL_ACE_FAILED 2-Critical Failed to [chars][chars] SGACL '[chars]' for SGT=[chars] due to ACE '[chars]' error. Download will be retried in 60 seconds An error occurred in the ACE while CTS attempted to acquire SGACL policy from the policy server. Retry will be attempted in 60 seconds - LOG_STD_ACTION CTS-2-CACHE_FILE_CHUNK_ALLOC_FAILURE 2-Critical Failed to allocate memory for CTS Cache Filename chunks. Failed to allocate memory for CTS Cache Filename chunks This is an indicator of a critical memory issue. - LOG_STD_ACTION CTS-2-CACHE_FILE_CHUNK_ALLOC_FAILURE 2-Critical Failed to allocate memory for CTS Cache Filename chunks. Failed to allocate memory for CTS Cache Filename chunks This is an indicator of a critical memory issue. - LOG_STD_ACTION CTS-2-CTS_CRIT 2-Critical [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-2-CTS_CRIT 2-Critical [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-2-FIPS_SW_POST_FAIL 2-Critical Software crypto POST Failure One or more power-up software crypto algorithmic known answer tests have failed. - LOG_STD_ACTION CTS-2-FIPS_SW_POST_FAIL 2-Critical Software crypto POST Failure One or more power-up software crypto algorithmic known answer tests have failed. - LOG_STD_ACTION CTS-3-AAA_NO_CONTEXT 3-Error Failed to retrieve AAA context to construct AAA attribute for RADIUS request CTS AAA Request Add : Failed to retrieve AAA context to construct AAA attribute for RADIUS request - LOG_STD_ACTION CTS-3-AAA_NO_CONTEXT 3-Error Failed to retrieve AAA context to construct AAA attribute for RADIUS request CTS AAA Request Add : Failed to retrieve AAA context to construct AAA attribute for RADIUS request - LOG_STD_ACTION CTS-3-AAA_NO_CONTEXT 3-Error Failed to retrieve AAA context to construct AAA attribute for RADIUS request CTS AAA Request Add : Failed to retrieve AAA context to construct AAA attribute for RADIUS request - LOG_STD_ACTION CTS-3-AAA_NO_RADIUS_SERVER 3-Error No RADIUS servers available for CTS AAA request for [chars] CTS AAA Request Setup : No RADIUS servers available for CTS AAA - LOG_STD_ACTION CTS-3-AAA_NO_RADIUS_SERVER 3-Error No RADIUS servers available for CTS AAA request for [chars] CTS AAA Request Setup : No RADIUS servers available for CTS AAA - LOG_STD_ACTION CTS-3-AAA_NO_RADIUS_SERVER 3-Error No RADIUS servers available for CTS AAA request for [chars] CTS AAA Request Setup : No RADIUS servers available for CTS AAA - LOG_STD_ACTION CTS-3-ACL_UNCONFIGURED 3-Error Access-list [chars] has been dynamically unconfigured from CTS policy because it has been [chars]. An access-list configured as defining CTS L3 traffic or exemption policy has been deleted or modified so that it can no longer be used for defining CTS policy. It has therefore been removed from the CTS layer3 policy configuration. - - CTS-3-ACL_UNCONFIGURED 3-Error Access-list [chars] has been dynamically unconfigured from CTS policy because it has been [chars]. An access-list configured as defining CTS L3 traffic or exemption policy has been deleted or modified so that it can no longer be used for defining CTS policy. It has therefore been removed from the CTS layer3 policy configuration. - - CTS-3-AUTHZ_ACL_INFO_STALE 3-Error ACL information is not valid. An error occurred while CTS attempted to access ACL information with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_ACL_INFO_STALE 3-Error ACL information is not valid. An error occurred while CTS attempted to access ACL information with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_ACL_LIST_STALE 3-Error ACL named list having ACE information is not valid. An error occurred while CTS attempted to access ACL list with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_ACL_LIST_STALE 3-Error ACL named list having ACE information is not valid. An error occurred while CTS attempted to access ACL list with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_ADD_DATA_FAILED 3-Error [chars] failed to add [chars] to [chars] An error occurred while CTS Authz attempted to build its database. - LOG_STD_ACTION CTS-3-AUTHZ_ADD_DATA_FAILED 3-Error [chars] failed to add [chars] to [chars] An error occurred while CTS Authz attempted to build its database. - LOG_STD_ACTION CTS-3-AUTHZ_ADD_DATA_FAILED 3-Error [chars] failed to add [chars] to [chars] An error occurred while CTS Authz attempted to build its database. - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_MSGT_WRITE_FAIL 3-Error [chars] failed to write Multicast SGT Table to cache file[chars] CTS Cache: Failed to write Multicast SGT Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_MSGT_WRITE_FAIL 3-Error [chars] failed to write Multicast SGT Table to cache file[chars] CTS Cache: Failed to write Multicast SGT Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_MSGT_WRITE_FAIL 3-Error [chars] failed to write Multicast SGT Table to cache file[chars] CTS Cache: Failed to write Multicast SGT Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_FAIL 3-Error [chars] failed to open cache file[chars] for read CTS Cache read: Failed to open cache file for read - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_FAIL 3-Error [chars] failed to open cache file[chars] for read CTS Cache read: Failed to open cache file for read - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_FAIL 3-Error [chars] failed to open cache file[chars] for read CTS Cache read: Failed to open cache file for read - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_WRITE_FAIL 3-Error [chars] failed to open cache file[chars] for write CTS Cache: Failed to open cache file for write - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_WRITE_FAIL 3-Error [chars] failed to open cache file[chars] for write CTS Cache: Failed to open cache file for write - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_OPEN_WRITE_FAIL 3-Error [chars] failed to open cache file[chars] for write CTS Cache: Failed to open cache file for write - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_PEER_POL_WRITE_FAIL 3-Error Failed to write peer policy to cache CTS Authz Cache: Failed to write peer policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_PEER_POL_WRITE_FAIL 3-Error Failed to write peer policy to cache CTS Authz Cache: Failed to write peer policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_PEER_POL_WRITE_FAIL 3-Error Failed to write peer policy to cache CTS Authz Cache: Failed to write peer policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_READ_FAIL 3-Error [chars] failed to read from cache file[chars] CTS Cache: Failed to read from cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_READ_FAIL 3-Error [chars] failed to read from cache file[chars] CTS Cache: Failed to read from cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_READ_FAIL 3-Error [chars] failed to read from cache file[chars] CTS Cache: Failed to read from cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_POL_WRITE_FAIL 3-Error Failed to write SGT policy to cache CTS Authz Cache: Failed to write SGT policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_POL_WRITE_FAIL 3-Error Failed to write SGT policy to cache CTS Authz Cache: Failed to write SGT policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_POL_WRITE_FAIL 3-Error Failed to write SGT policy to cache CTS Authz Cache: Failed to write SGT policy to cache - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_WRITE_FAIL 3-Error [chars] failed to write SGT SG Name Table to cache file[chars] CTS Cache: Failed to write SGT SG Name Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_WRITE_FAIL 3-Error [chars] failed to write SGT SG Name Table to cache file[chars] CTS Cache: Failed to write SGT SG Name Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SGT_WRITE_FAIL 3-Error [chars] failed to write SGT SG Name Table to cache file[chars] CTS Cache: Failed to write SGT SG Name Table to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SRV_WRITE_FAIL 3-Error [chars] failed to write server list to cache file[chars] CTS Cache: Failed to write server list to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SRV_WRITE_FAIL 3-Error [chars] failed to write server list to cache file[chars] CTS Cache: Failed to write server list to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHE_SRV_WRITE_FAIL 3-Error [chars] failed to write server list to cache file[chars] CTS Cache: Failed to write server list to cache file - LOG_STD_ACTION CTS-3-AUTHZ_CACHED_DATA_READ_FAIL 3-Error [chars] failed to read cached data CTS Cache: Failed to read cached data - LOG_STD_ACTION CTS-3-AUTHZ_CACHED_DATA_READ_FAIL 3-Error [chars] failed to read cached data CTS Cache: Failed to read cached data - LOG_STD_ACTION CTS-3-AUTHZ_CACHED_DATA_READ_FAIL 3-Error [chars] failed to read cached data CTS Cache: Failed to read cached data - LOG_STD_ACTION CTS-3-AUTHZ_DATA_CREATE_FAILED 3-Error [chars] failed to create [chars] An error occurred while CTS Authz attempts to create an internal data structure. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_CREATE_FAILED 3-Error [chars] failed to create [chars] An error occurred while CTS Authz attempts to create an internal data structure. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_CREATE_FAILED 3-Error [chars] failed to create [chars] An error occurred while CTS Authz attempts to create an internal data structure. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT 3-Error [chars] encountered [chars][dec] exceeds max[dec] Data exceeds maximum limits allowed. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT 3-Error [chars] encountered [chars][dec] exceeds max[dec] Data exceeds maximum limits allowed. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_EXCEEDS_LIMIT 3-Error [chars] encountered [chars][dec] exceeds max[dec] Data exceeds maximum limits allowed. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_FAILED 3-Error [chars] failed to obtain [chars] An error occurred while CTS Authz attempted to get/create a data structure - LOG_STD_ACTION CTS-3-AUTHZ_DATA_FAILED 3-Error [chars] failed to obtain [chars] An error occurred while CTS Authz attempted to get/create a data structure - LOG_STD_ACTION CTS-3-AUTHZ_DATA_FAILED 3-Error [chars] failed to obtain [chars] An error occurred while CTS Authz attempted to get/create a data structure - LOG_STD_ACTION CTS-3-AUTHZ_DATA_NULL 3-Error [chars] encounters NULL [chars] An unexpected NULL pointer/data is encountered. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_NULL 3-Error [chars] encounters NULL [chars] An unexpected NULL pointer/data is encountered. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_NULL 3-Error [chars] encounters NULL [chars] An unexpected NULL pointer/data is encountered. - LOG_STD_ACTION CTS-3-AUTHZ_DATA_UNINIT 3-Error [chars] appears uninitialized CTS Authz unexpectedly encountered an unitialized data - LOG_STD_ACTION CTS-3-AUTHZ_DATA_UNINIT 3-Error [chars] appears uninitialized CTS Authz unexpectedly encountered an unitialized data - LOG_STD_ACTION CTS-3-AUTHZ_DATA_UNINIT 3-Error [chars] appears uninitialized CTS Authz unexpectedly encountered an unitialized data - LOG_STD_ACTION CTS-3-AUTHZ_ENTRY_HTTP_FAILED 3-Error Policy Acquisition failed to transmit HTTP request for peer[chars] sgt[chars] Policy acquisition failed to transmit HTTP request - LOG_STD_ACTION CTS-3-AUTHZ_ENTRY_HTTP_FAILED 3-Error Policy Acquisition failed to transmit HTTP request for peer[chars] sgt[chars] Policy acquisition failed to transmit HTTP request - LOG_STD_ACTION CTS-3-AUTHZ_ENTRY_RADIUS_FAILED 3-Error Policy Acquisition failed to transmit RADIUS request for peer[chars] sgt[chars] - - - CTS-3-AUTHZ_ENTRY_RADIUS_FAILED 3-Error Policy Acquisition failed to transmit RADIUS request for peer[chars] sgt[chars] - - - CTS-3-AUTHZ_ENTRY_RADIUS_FAILED 3-Error Policy Acquisition failed to transmit RADIUS request for peer[chars] sgt[chars] - - - CTS-3-AUTHZ_FAILED_SYNC_RCV 3-Error Standby failed receive sync msg[chars] An error occcured while the Standby is receiving sync data from the Active. - LOG_STD_ACTION CTS-3-AUTHZ_FAILED_SYNC_RCV 3-Error Standby failed receive sync msg[chars] An error occcured while the Standby is receiving sync data from the Active. - LOG_STD_ACTION CTS-3-AUTHZ_FAILED_SYNC_RCV 3-Error Standby failed receive sync msg[chars] An error occcured while the Standby is receiving sync data from the Active. - LOG_STD_ACTION CTS-3-AUTHZ_GENERIC_FAILURE 3-Error [chars] [chars] CTS Authz encountered internal error. - LOG_STD_ACTION CTS-3-AUTHZ_GENERIC_FAILURE 3-Error [chars] [chars] CTS Authz encountered internal error. - LOG_STD_ACTION CTS-3-AUTHZ_GENERIC_FAILURE 3-Error [chars] [chars] CTS Authz encountered internal error. - LOG_STD_ACTION CTS-3-AUTHZ_INVALID_DATA 3-Error [chars] encountered invalid [chars] CTS Authz encountered an unexpected invalid data type. - LOG_STD_ACTION CTS-3-AUTHZ_INVALID_DATA 3-Error [chars] encountered invalid [chars] CTS Authz encountered an unexpected invalid data type. - LOG_STD_ACTION CTS-3-AUTHZ_INVALID_DATA 3-Error [chars] encountered invalid [chars] CTS Authz encountered an unexpected invalid data type. - LOG_STD_ACTION CTS-3-AUTHZ_NOT_SUPPORTED 3-Error [chars] encountered [chars] not unsupported CTS encountered an unsupported data type or feature. This could be due to incompatibility - LOG_STD_ACTION CTS-3-AUTHZ_NOT_SUPPORTED 3-Error [chars] encountered [chars] not unsupported CTS encountered an unsupported data type or feature. This could be due to incompatibility - LOG_STD_ACTION CTS-3-AUTHZ_NOT_SUPPORTED 3-Error [chars] encountered [chars] not unsupported CTS encountered an unsupported data type or feature. This could be due to incompatibility - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_ACL_DEL_FAILED 3-Error Failed to delete ACL information. Invalid ACL [chars]. An error occurred while CTS attempted to delete ACL info with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_ACL_DEL_FAILED 3-Error Failed to delete ACL information. Invalid ACL [chars]. An error occurred while CTS attempted to delete ACL info with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_FAIL_TO_REMOVE 3-Error Failed to remove [chars] policy from the authorization dbase An error occured while CTS attempted to remove the specified policy from its database. This could result in an action not being accomplished. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_FAIL_TO_REMOVE 3-Error Failed to remove [chars] policy from the authorization dbase An error occured while CTS attempted to remove the specified policy from its database. This could result in an action not being accomplished. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_FAIL_TO_REMOVE 3-Error Failed to remove [chars] policy from the authorization dbase An error occured while CTS attempted to remove the specified policy from its database. This could result in an action not being accomplished. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INGRESS_FAILED 3-Error Failed to [chars] Ingress policy for [chars] An error occurred while CTS attempted to acquire or install an Ingress policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INGRESS_FAILED 3-Error Failed to [chars] Ingress policy for [chars] An error occurred while CTS attempted to acquire or install an Ingress policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INGRESS_FAILED 3-Error Failed to [chars] Ingress policy for [chars] An error occurred while CTS attempted to acquire or install an Ingress policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INTERNAL_FAILED 3-Error Failed to acquire/install policy for [chars] due to internal error An error occurred while CTS attempted to acquire/install a policy which may be caused by internal software error - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INTERNAL_FAILED 3-Error Failed to acquire/install policy for [chars] due to internal error An error occurred while CTS attempted to acquire/install a policy which may be caused by internal software error - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_INTERNAL_FAILED 3-Error Failed to acquire/install policy for [chars] due to internal error An error occurred while CTS attempted to acquire/install a policy which may be caused by internal software error - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED 3-Error Failed to download peer policy for [chars] An error occurred while CTS attempted to acquire peer policy from the policy server - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED 3-Error Failed to download peer policy for [chars] An error occurred while CTS attempted to acquire peer policy from the policy server - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_PEER_DOWNLOAD_FAILED 3-Error Failed to download peer policy for [chars] An error occurred while CTS attempted to acquire peer policy from the policy server - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_SGACL_ACE_FAILED 3-Error Failed to [chars][chars] SGACL '[chars]' for SGT=[chars] due to ACE '[chars]' error An error occurred in the ACE while CTS attempted to acquire SGACL policy from the policy server. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_SGACL_FAILED 3-Error Failed to [chars][chars] SGACL [chars] for SGT=[chars] An error occurred while CTS attempted to acquire SGACL policy from the policy server. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_SGACL_FAILED 3-Error Failed to [chars][chars] SGACL [chars] for SGT=[chars] An error occurred while CTS attempted to acquire SGACL policy from the policy server. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_SGACL_FAILED 3-Error Failed to [chars][chars] SGACL [chars] for SGT=[chars] An error occurred while CTS attempted to acquire SGACL policy from the policy server. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_WILDCARD_FAILED 3-Error Failed to download default/unknown policy An error occurred while CTS attempted to acquire wildcard policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_WILDCARD_FAILED 3-Error Failed to download default/unknown policy An error occurred while CTS attempted to acquire wildcard policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_POLICY_WILDCARD_FAILED 3-Error Failed to download default/unknown policy An error occurred while CTS attempted to acquire wildcard policy from the ACS. - LOG_STD_ACTION CTS-3-AUTHZ_SESSION_SM_START_FAILED 3-Error Failed to initialize the environment-data module Failed to initialize the environment-data module - LOG_STD_ACTION CTS-3-AUTHZ_SESSION_SM_START_FAILED 3-Error Failed to initialize the environment-data module Failed to initialize the environment-data module - LOG_STD_ACTION CTS-3-AUTHZ_SESSION_SM_START_FAILED 3-Error Failed to initialize the environment-data module Failed to initialize the environment-data module - LOG_STD_ACTION CTS-3-AUTHZ_SESSION_UNINST_SGACL_FAILED 3-Error Failed to detach session handle from SGACL list for sgt[chars] - - - CTS-3-AUTHZ_SESSION_UNINST_SGACL_FAILED 3-Error Failed to detach session handle from SGACL list for sgt[chars] - - - CTS-3-AUTHZ_SESSION_UNINST_SGACL_FAILED 3-Error Failed to detach session handle from SGACL list for sgt[chars] - - - CTS-3-AUTHZ_SGT_POLICY_DEL_FAILED 3-Error Failed to delete sgt policy for sgt [chars]. An error occurred while CTS attempted to delete sgt policy with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_SGT_POLICY_DEL_FAILED 3-Error Failed to delete sgt policy for sgt [chars]. An error occurred while CTS attempted to delete sgt policy with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_SGT_POLICY_STALE 3-Error sgt policy for sgt '[chars]' is not valid. An error occurred while CTS attempted to access sgt policy with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_SGT_POLICY_STALE 3-Error sgt policy for sgt '[chars]' is not valid. An error occurred while CTS attempted to access sgt policy with invalid handle. - LOG_STD_ACTION CTS-3-AUTHZ_SM_FAILED 3-Error Failed to start the authorization entry state machine to start policy acquisition for peer[chars] - - - CTS-3-AUTHZ_SM_FAILED 3-Error Failed to start the authorization entry state machine to start policy acquisition for peer[chars] - - - CTS-3-AUTHZ_SM_FAILED 3-Error Failed to start the authorization entry state machine to start policy acquisition for peer[chars] - - - CTS-3-AUTHZ_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS Authz is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-AUTHZ_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS Authz is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-AUTHZ_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS Authz is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-AUTHZ_TREE_MAP_INSERT_FAILED 3-Error Failed to insert the authz entry info into tree map for peer[chars] - - - CTS-3-AUTHZ_TREE_MAP_INSERT_FAILED 3-Error Failed to insert the authz entry info into tree map for peer[chars] - - - CTS-3-AUTHZ_TREE_MAP_INSERT_FAILED 3-Error Failed to insert the authz entry info into tree map for peer[chars] - - - CTS-3-AUTHZ_UNINST_SESSION_FR_NAMELIST_FAILED 3-Error Failed to locate named list to uninstall session Failed to locate named list to uninstall session - LOG_STD_ACTION CTS-3-AUTHZ_UNINST_SESSION_FR_NAMELIST_FAILED 3-Error Failed to locate named list to uninstall session Failed to locate named list to uninstall session - LOG_STD_ACTION CTS-3-AUTHZ_UNINST_SESSION_FR_NAMELIST_FAILED 3-Error Failed to locate named list to uninstall session Failed to locate named list to uninstall session - LOG_STD_ACTION CTS-3-CACHE_FILE_OPEN_FAILED 3-Error Failed to open cache file: [chars] error: [chars] Cache file could not be opened for read CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_FILE_OPEN_FAILED 3-Error Failed to open cache file: [chars] error: [chars] Cache file could not be opened for read CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_INVALID_DIRECTORY_PATH 3-Error Cache Invalid Directory Path: [chars] exceeds maximum allowed length [dec] Cache invalid directory path. Cache file will not be opened for read/write and CTS cache functionality will not work as expected. - _ACTION CTS-3-CACHE_INVALID_DIRECTORY_PATH 3-Error Cache Invalid Directory Path: [chars] exceeds maximum allowed length [dec] Cache invalid directory path. Cache file will not be opened for read/write and CTS cache functionality will not work as expected. - _ACTION CTS-3-CACHE_INVALID_IFS 3-Error Cache Invalid IFS: Error opening [chars] - [chars] Failure in validating file system. Cache file will not be opened for read/write and CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_INVALID_IFS 3-Error Cache Invalid IFS: Error opening [chars] - [chars] Failure in validating file system. Cache file will not be opened for read/write and CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_READ_BAD_FILE_MAGIC 3-Error Cache read failed due to bad file magic. Cache read failed due to bad file magic. CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_READ_BAD_FILE_MAGIC 3-Error Cache read failed due to bad file magic. Cache read failed due to bad file magic. CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_READ_CRC_ERROR 3-Error Cache read failed due to mismatch in CRC - file CRC[hec] calculated CRC[hec] - - - CTS-3-CACHE_READ_CRC_ERROR 3-Error Cache read failed due to mismatch in CRC - file CRC[hec] calculated CRC[hec] - - - CTS-3-CACHE_READ_FILE_HEADER_ERROR 3-Error Cache read of file [chars] failed due to file header error. Cache read failed due to file header error. CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CACHE_READ_FILE_HEADER_ERROR 3-Error Cache read of file [chars] failed due to file header error. Cache read failed due to file header error. CTS cache functionality will not work as expected. - LOG_STD_ACTION CTS-3-CAP_INVALID_SIZE 3-Error CTS HA empty tlv size. Received empty tlv list during capability negotiation. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CAP_INVALID_SIZE 3-Error CTS HA empty tlv size. Received empty tlv list during capability negotiation. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CAP_NOT_COMPATIBLE 3-Error CTS HA capability not compatible CTS HA failed during capability negotiation. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CAP_NOT_COMPATIBLE 3-Error CTS HA capability not compatible CTS HA failed during capability negotiation. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CHKPT_REG_FAIL 3-Error CTS HA add CTS checkpoint client failure. CTS HA failed to add checkpoint client. No CTS data will be synced to Standby in this case. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CHKPT_REG_FAIL 3-Error CTS HA add CTS checkpoint client failure. CTS HA failed to add checkpoint client. No CTS data will be synced to Standby in this case. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CORE_PROCESS_CREATION_FAILURE 3-Error Failed to create CTS_CORE process CTS_CORE: Failed to create CTS_CORE process - LOG_STD_ACTION CTS-3-CORE_PROCESS_CREATION_FAILURE 3-Error Failed to create CTS_CORE process CTS_CORE: Failed to create CTS_CORE process - LOG_STD_ACTION CTS-3-CORE_PROCESS_TERMINATED 3-Error Process getting killed since queue is not created CTS_CORE: Process getting killed since queue is not created - LOG_STD_ACTION CTS-3-CORE_PROCESS_TERMINATED 3-Error Process getting killed since queue is not created CTS_CORE: Process getting killed since queue is not created - LOG_STD_ACTION CTS-3-CTS_DISALLOW_L2_CONFIG 3-Error [chars].\nRemoving CTS Layer2 configuration from interface[chars] - - - CTS-3-CTS_DISALLOW_L2_CONFIG 3-Error [chars].\nRemoving CTS Layer2 configuration from interface[chars] - - - CTS-3-CTS_DISALLOW_L3_CONFIG 3-Error [chars].\nRemoving CTS Layer3 TrustSec Forwarding configuration from interface[chars] Platform ASIC does not support CTS Layer2 and CTS layer3 TrustSec Forwarding configurations to co-exist on the same ASIC instance - LOG_STD_ACTION CTS-3-CTS_DISALLOW_L3_CONFIG 3-Error [chars].\nRemoving CTS Layer3 TrustSec Forwarding configuration from interface[chars] Platform ASIC does not support CTS Layer2 and CTS layer3 TrustSec Forwarding configurations to co-exist on the same ASIC instance - LOG_STD_ACTION CTS-3-CTS_ERR 3-Error [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CTS_ERR 3-Error [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_CREDENTIALS 3-Error Valid Policy-server credentials have not configured on device CTS policy-server username is not configured - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_CREDENTIALS 3-Error Valid Policy-server credentials have not configured on device CTS policy-server username is not configured - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_ENCRYPT_REVERSIBLE 3-Error Password conversion failed CTS policy-server password conversion failed - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_ENCRYPT_REVERSIBLE 3-Error Password conversion failed CTS policy-server password conversion failed - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_ENCRYPT_TEMP 3-Error Password conversion failed CTS policy-server password conversion failed - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_ENCRYPT_TEMP 3-Error Password conversion failed CTS policy-server password conversion failed - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_INVALID_CREDENTIALS 3-Error Invalid Policy-server credentials have configured on device OR Server port number is incorrect CTS policy-server username or password are invalid - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_INVALID_CREDENTIALS 3-Error Invalid Policy-server credentials have configured on device OR Server port number is incorrect CTS policy-server username or password are invalid - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_SG_TBL_ALLOC 3-Error Server group table memory allocation failed CTS HTTP based download will impact - LOG_STD_ACTION CTS-3-CTS_POLICY_SERVER_SG_TBL_ALLOC 3-Error Server group table memory allocation failed CTS HTTP based download will impact - LOG_STD_ACTION CTS-3-DOT1X_FORCE_PORT_AUTHORIZED_FAILED 3-Error Failed to force dot1x port authorized for int[chars] An error occcured while CTS attempts to force dot1x port authorized on a CTS link - LOG_STD_ACTION CTS-3-DOT1X_FORCE_PORT_AUTHORIZED_FAILED 3-Error Failed to force dot1x port authorized for int[chars] An error occcured while CTS attempts to force dot1x port authorized on a CTS link - LOG_STD_ACTION CTS-3-DOT1X_UNCONFIGURE_FAILURE 3-Error Failed to unconfigure dot1x on int[chars] CTS_CORE: Failed to unconfigure dot1x - LOG_STD_ACTION CTS-3-DOT1X_UNCONFIGURE_FAILURE 3-Error Failed to unconfigure dot1x on int[chars] CTS_CORE: Failed to unconfigure dot1x - LOG_STD_ACTION CTS-3-ENTROPY_SRC_FAILURE 3-Error Entropy source failed health test The periodic health tests done on the CTR-DRBG crypto implementation indicated an error in obtaining entropy. Recommended action is to crash. - - CTS-3-ENTROPY_SRC_FAILURE 3-Error Entropy source failed health test The periodic health tests done on the CTR-DRBG crypto implementation indicated an error in obtaining entropy. Recommended action is to crash. - - CTS-3-ENV_DATA_ERROR 3-Error Environment data error in [chars] state ENV data error - LOG_STD_NO_ACTION CTS-3-ENV_DATA_ERROR 3-Error Environment data error in [chars] state ENV data error - LOG_STD_NO_ACTION CTS-3-ENV_DATA_ERROR 3-Error Environment data error in [chars] state ENV data error - LOG_STD_NO_ACTION CTS-3-ENV_DATA_INIT_FAILED 3-Error Failed to initialize and start the authorization state machine Failed to initialize and start the authorization state machine - LOG_STD_ACTION CTS-3-ENV_DATA_INIT_FAILED 3-Error Failed to initialize and start the authorization state machine Failed to initialize and start the authorization state machine - LOG_STD_ACTION CTS-3-ENV_DATA_INIT_FAILED 3-Error Failed to initialize and start the authorization state machine Failed to initialize and start the authorization state machine - LOG_STD_ACTION CTS-3-FIPS_SW_SEND_POST_RESULT_FAIL 3-Error Software crypto POST FAIL SCP message send failed Power-up crypto software algorithmic tests have failed and the SCP message - LOG_STD_ACTION CTS-3-FIPS_SW_SEND_POST_RESULT_FAIL 3-Error Software crypto POST FAIL SCP message send failed Power-up crypto software algorithmic tests have failed and the SCP message - LOG_STD_ACTION CTS-3-GCM_NO_LICENSE 3-Error CTS link [chars] is being shut down: please install MACSec Encryption License http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. All CTS links configured to run gcm-encryption will be held in administratively down state until the gcm-encrytion is removed from the interface configuration or until a MACSec Encryption License is installed. - "Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm." CTS-3-GCM_NO_LICENSE 3-Error CTS link [chars] is being shut down: please install MACSec Encryption License http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. All CTS links configured to run gcm-encryption will be held in administratively down state until the gcm-encrytion is removed from the interface configuration or until a MACSec Encryption License is installed. - "Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm." CTS-3-GENERIC_FAILURE 3-Error [chars] [chars] CTS Core encountered internal error. - LOG_STD_ACTION CTS-3-GENERIC_FAILURE 3-Error [chars] [chars] CTS Core encountered internal error. - LOG_STD_ACTION CTS-3-GET_BUFFER 3-Error CTS HA ISSU client failed to get buffer for message. Error: [dec] [chars] The CTS HA ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show logging and show checkpoint client" CTS-3-GET_BUFFER 3-Error CTS HA ISSU client failed to get buffer for message. Error: [dec] [chars] The CTS HA ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show logging and show checkpoint client" CTS-3-GLOBAL_DOT1X_DISABLED 3-Error Global dot1x config is currently disabled - CTS will not run Global dot1x is not enabled and hence CTS will not run - LOG_STD_ACTION CTS-3-GLOBAL_DOT1X_DISABLED 3-Error Global dot1x config is currently disabled - CTS will not run Global dot1x is not enabled and hence CTS will not run - LOG_STD_ACTION CTS-3-IFC_ADD_SUPPLICANT_FAIL 3-Error Failed to add supplicant cannot open port[chars] - - - CTS-3-IFC_ADD_SUPPLICANT_FAIL 3-Error Failed to add supplicant cannot open port[chars] - - - CTS-3-IFC_CACHE_BAD_LEN 3-Error Cache File [chars] bad length [dec] expecting [dec] IFC Cache file bad length may be corrupted. - LOG_STD_ACTION CTS-3-IFC_CACHE_BAD_LEN 3-Error Cache File [chars] bad length [dec] expecting [dec] IFC Cache file bad length may be corrupted. - LOG_STD_ACTION CTS-3-IFC_CACHE_RESTORE_FAIL 3-Error Cache Restoration Failed IFC Cache restoration failed owing to errors in NVRAM file open operation. Even though CTS cache is enabled link bring up cannot bypass IFC state machine - LOG_STD_ACTION CTS-3-IFC_CACHE_RESTORE_FAIL 3-Error Cache Restoration Failed IFC Cache restoration failed owing to errors in NVRAM file open operation. Even though CTS cache is enabled link bring up cannot bypass IFC state machine - LOG_STD_ACTION CTS-3-IFC_CACHE_UPDATE_FAIL 3-Error Cache Update Failed IFC Cache update failed owing to errors in NVRAM file write operation. - LOG_STD_ACTION CTS-3-IFC_CACHE_UPDATE_FAIL 3-Error Cache Update Failed IFC Cache update failed owing to errors in NVRAM file write operation. - LOG_STD_ACTION CTS-3-IFC_DATA_DESC_ENCODE_FAILED 3-Error [chars] failed to encode the data-descriptor for int[chars] An error occured while the system attempted to encode the swidb into the data-descriptor - LOG_STD_ACTION CTS-3-IFC_DATA_DESC_ENCODE_FAILED 3-Error [chars] failed to encode the data-descriptor for int[chars] An error occured while the system attempted to encode the swidb into the data-descriptor - LOG_STD_ACTION CTS-3-IFC_DATA_NULL 3-Error [chars] encounters NULL [chars] An unexpected NULL pointer/data is encountered. - LOG_STD_ACTION CTS-3-IFC_DATA_NULL 3-Error [chars] encounters NULL [chars] An unexpected NULL pointer/data is encountered. - LOG_STD_ACTION CTS-3-IFC_FAIL_PRGM_PSGT 3-Error Could not program hardware for propagate SGT Port SGT[dec] IFC could not program hardware for propagate SGT - LOG_STD_ACTION CTS-3-IFC_FAIL_PRGM_PSGT 3-Error Could not program hardware for propagate SGT Port SGT[dec] IFC could not program hardware for propagate SGT - LOG_STD_ACTION CTS-3-IFC_FAILED_AUTHC_SUCCESS_NOTIFY 3-Error Failed to send authentication success to the core for int[chars] - - - CTS-3-IFC_FAILED_AUTHC_SUCCESS_NOTIFY 3-Error Failed to send authentication success to the core for int[chars] - - - CTS-3-IFC_FAILED_AUTHZ_FAIL_NOTIFY 3-Error Failed to send authorization failure to the core for int[chars] - - - CTS-3-IFC_FAILED_AUTHZ_FAIL_NOTIFY 3-Error Failed to send authorization failure to the core for int[chars] - - - CTS-3-IFC_FAILED_AUTHZ_SUCCESS_NOTIFY 3-Error Failed to send authorization success to the core for int[chars] - - - CTS-3-IFC_FAILED_AUTHZ_SUCCESS_NOTIFY 3-Error Failed to send authorization success to the core for int[chars] - - - CTS-3-IFC_FAILED_DISCONNECT_NOTIFY 3-Error Failed to send disconnect notify to the core for int[chars] - - - CTS-3-IFC_FAILED_DISCONNECT_NOTIFY 3-Error Failed to send disconnect notify to the core for int[chars] - - - CTS-3-IFC_FAILED_ENV_DATA_DNLD 3-Error Failed to download environment data for int[chars] - - - CTS-3-IFC_FAILED_ENV_DATA_DNLD 3-Error Failed to download environment data for int[chars] - - - CTS-3-IFC_FAILED_SAP_FAIL_NOTIFY 3-Error Failed to send SAP failure to the core for int[chars] - - - CTS-3-IFC_FAILED_SAP_FAIL_NOTIFY 3-Error Failed to send SAP failure to the core for int[chars] - - - CTS-3-IFC_FAILED_SAP_SUCCESS_NOTIFY 3-Error Failed to send SAP success to the core for int[chars] - - - CTS-3-IFC_FAILED_SAP_SUCCESS_NOTIFY 3-Error Failed to send SAP success to the core for int[chars] - - - CTS-3-IFC_LINK_OBJ_FAILED 3-Error [chars] failed to get link_obj for int[chars] An error occured while CTS IFC attempts to access the link object. - LOG_STD_ACTION CTS-3-IFC_LINK_OBJ_FAILED 3-Error [chars] failed to get link_obj for int[chars] An error occured while CTS IFC attempts to access the link object. - LOG_STD_ACTION CTS-3-IFC_LOST_AUTHC_REAUTH_TIMER_CXT 3-Error Lost AUTHC reauth timer context IFC Lost AUTHC reauth timer context - LOG_STD_ACTION CTS-3-IFC_LOST_AUTHC_REAUTH_TIMER_CXT 3-Error Lost AUTHC reauth timer context IFC Lost AUTHC reauth timer context - LOG_STD_ACTION CTS-3-IFC_LOST_DOT1X_PAE_TIMER_CXT 3-Error Lost DOT1x PAE timer context IFC Lost DOT1x PAE timer context - LOG_STD_ACTION CTS-3-IFC_LOST_DOT1X_PAE_TIMER_CXT 3-Error Lost DOT1x PAE timer context IFC Lost DOT1x PAE timer context - LOG_STD_ACTION CTS-3-IFC_LOST_SOCK_CLEANUP_TIMER_CXT 3-Error Lost socket cleanup timer context IFC Lost socket cleanup timer context - LOG_STD_ACTION CTS-3-IFC_LOST_SOCK_CLEANUP_TIMER_CXT 3-Error Lost socket cleanup timer context IFC Lost socket cleanup timer context - LOG_STD_ACTION CTS-3-IFC_LOST_TIMER_CXT 3-Error Lost Timer context IFC Lost Timer context - LOG_STD_ACTION CTS-3-IFC_LOST_TIMER_CXT 3-Error Lost Timer context IFC Lost Timer context - LOG_STD_ACTION CTS-3-IFC_NO_IDB_IN_AUTHORIZE_STATE 3-Error Authorization State: IDB could not be retrieved: state[chars] peer[chars] - - - CTS-3-IFC_NO_IDB_IN_AUTHORIZE_STATE 3-Error Authorization State: IDB could not be retrieved: state[chars] peer[chars] - - - CTS-3-IFC_NO_IDB_IN_SAP_STATE 3-Error SAP State: IDB could not be retrieved IFC SAP State: IDB could not be retrieved - LOG_STD_ACTION CTS-3-IFC_NO_IDB_IN_SAP_STATE 3-Error SAP State: IDB could not be retrieved IFC SAP State: IDB could not be retrieved - LOG_STD_ACTION CTS-3-IFC_NO_IDB_IN_SWACT 3-Error Failed to locate IDB in link object Failed to locate IDB in link object - LOG_STD_ACTION CTS-3-IFC_NO_IDB_IN_SWACT 3-Error Failed to locate IDB in link object Failed to locate IDB in link object - LOG_STD_ACTION CTS-3-IFC_RX_AUTHC_SUCCESS_FAIL 3-Error Received AUTHC Success for peer[chars] role[chars] int[chars] IFC Received AUTHC success but failed to process due to error - LOG_STD_ACTION CTS-3-IFC_RX_AUTHC_SUCCESS_FAIL 3-Error Received AUTHC Success for peer[chars] role[chars] int[chars] IFC Received AUTHC success but failed to process due to error - LOG_STD_ACTION CTS-3-IFC_SM_INIT_FAIL 3-Error SM INIT failed IFC SM INIT failed - LOG_STD_ACTION CTS-3-IFC_SM_INIT_FAIL 3-Error SM INIT failed IFC SM INIT failed - LOG_STD_ACTION CTS-3-IFC_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS IFC is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-IFC_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS IFC is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-IFC_SYNC_FAILED_2 3-Error [chars] Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS IFC is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-IFC_SYNC_FAILED_2 3-Error [chars] Failed to send [chars] sync msg[chars] to Standby An error occcured while CTS IFC is performing a sync to the Standby. - LOG_STD_ACTION CTS-3-INIT 3-Error CTS HA ISSU client initialization failed to [chars]. Error: [dec] [chars] CTS HA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-INIT 3-Error CTS HA ISSU client initialization failed to [chars]. Error: [dec] [chars] CTS HA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-INVALID_ACL 3-Error Access-list [chars] invalid for CTS policy: [chars]. An access-list configured as defining CTS L3 traffic or exemption policy cannot be used because of the specified reason. - - CTS-3-INVALID_ACL 3-Error Access-list [chars] invalid for CTS policy: [chars]. An access-list configured as defining CTS L3 traffic or exemption policy cannot be used because of the specified reason. - - CTS-3-INVALID_CTS_OPER_MODE 3-Error Invalid CTS Mode. Supported modes are Manual and Auto Invalid CTS Mode. Supported modes are manual and auto - LOG_STD_ACTION CTS-3-INVALID_CTS_OPER_MODE 3-Error Invalid CTS Mode. Supported modes are Manual and Auto Invalid CTS Mode. Supported modes are manual and auto - LOG_STD_ACTION CTS-3-INVALID_MSGID_RCV 3-Error [chars] received invalid HA/ISSU msgId[dec] CTS Core encountered an unexpected invalid HA/ISSU message ID. - LOG_STD_ACTION CTS-3-INVALID_MSGID_RCV 3-Error [chars] received invalid HA/ISSU msgId[dec] CTS Core encountered an unexpected invalid HA/ISSU message ID. - LOG_STD_ACTION CTS-3-LSC_CA_STORE_FAIL 3-Error Failed to install certificate of CA that issued our locally-significant certificate An error occurred while installing the certificate of our issuing CA. When this error occurs the locally-significant certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_CA_STORE_FAIL 3-Error Failed to install certificate of CA that issued our locally-significant certificate An error occurred while installing the certificate of our issuing CA. When this error occurs the locally-significant certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_CA_STORE_FAIL 3-Error Failed to install certificate of CA that issued our locally-significant certificate An error occurred while installing the certificate of our issuing CA. When this error occurs the locally-significant certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_ENROLL_FAIL 3-Error Failed to set re-enrollment attributes for CTS locally-significant certificate. An error occurred while setting the re-enrollment attributes for the new CTS certificate. When this error occurs the new certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_ENROLL_FAIL 3-Error Failed to set re-enrollment attributes for CTS locally-significant certificate. An error occurred while setting the re-enrollment attributes for the new CTS certificate. When this error occurs the new certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_ENROLL_FAIL 3-Error Failed to set re-enrollment attributes for CTS locally-significant certificate. An error occurred while setting the re-enrollment attributes for the new CTS certificate. When this error occurs the new certificate will be discarded and CTS will continue to use its password credentials for authentication. - - CTS-3-LSC_STORE_FAIL 3-Error Failed to install newly-provisioned locally-significant certificate. An error occurred while installing our locally significant certificate to be used for CTS. This means that we cannot be authenticated using a certificate. If a CTS password is available we will continue to authenticate using the password. - - CTS-3-LSC_STORE_FAIL 3-Error Failed to install newly-provisioned locally-significant certificate. An error occurred while installing our locally significant certificate to be used for CTS. This means that we cannot be authenticated using a certificate. If a CTS password is available we will continue to authenticate using the password. - - CTS-3-LSC_STORE_FAIL 3-Error Failed to install newly-provisioned locally-significant certificate. An error occurred while installing our locally significant certificate to be used for CTS. This means that we cannot be authenticated using a certificate. If a CTS password is available we will continue to authenticate using the password. - - CTS-3-MODE_LIST_CKSUM_ERROR 3-Error CTS SAP mode-list checksum failure on interface [chars].\n CTS SAP mode-list checksum failure has been detected on this interafce which could provide crypto services. This event may be caused by memory corruption occuring in the interface configutration or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the system has been forced to reload. - LOG_STD_ACTION CTS-3-MODE_LIST_CKSUM_ERROR 3-Error CTS SAP mode-list checksum failure on interface [chars].\n CTS SAP mode-list checksum failure has been detected on this interafce which could provide crypto services. This event may be caused by memory corruption occuring in the interface configutration or the memory area has been illegally modified. It may also be caused by software defects. As a result of this event the system has been forced to reload. - LOG_STD_ACTION CTS-3-MSG_NOT_COMPATIBLE_WITH_PEER 3-Error Message [dec] in component [dec] is not compatible with the peer. Message not compatible with the peer. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-MSG_NOT_COMPATIBLE_WITH_PEER 3-Error Message [dec] in component [dec] is not compatible with the peer. Message not compatible with the peer. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-PAC_PROVI_FAIL 3-Error PAC Provisioning failed for [inet] PAC Provisioning failed - LOG_STD_ACTION CTS-3-PAC_PROVI_FAIL 3-Error PAC Provisioning failed for [inet] PAC Provisioning failed - LOG_STD_ACTION CTS-3-PAC_PROVI_FAIL 3-Error PAC Provisioning failed for [inet] PAC Provisioning failed - LOG_STD_ACTION CTS-3-POLICY_COA_RBACL_FAILED 3-Error Failed to complete request for update-rbacl[chars]-[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-rbacl command - LOG_STD_ACTION CTS-3-POLICY_COA_RBACL_FAILED 3-Error Failed to complete request for update-rbacl[chars]-[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-rbacl command - LOG_STD_ACTION CTS-3-POLICY_COA_RBACL_FAILED 3-Error Failed to complete request for update-rbacl[chars]-[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-rbacl command - LOG_STD_ACTION CTS-3-POLICY_COA_SGT_FAILED 3-Error Failed to complete CoA request for update-sgt[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-sgt command - LOG_STD_ACTION CTS-3-POLICY_COA_SGT_FAILED 3-Error Failed to complete CoA request for update-sgt[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-sgt command - LOG_STD_ACTION CTS-3-POLICY_COA_SGT_FAILED 3-Error Failed to complete CoA request for update-sgt[chars] An error occurred while CTS attempted to service a Change of Authorization request for the update-sgt command - LOG_STD_ACTION CTS-3-POLICY_HA_PROC_FAIL 3-Error Error starting up HA switchover Policy refresh process. A failure has occurred in switchover which has prevented the policy refresh process to be lauched. User should manually refresh policies via the \cts refresh policy\ commad - "Issue command \"cts refresh policy\" and verify policy timers" " are active If timers do not start "LOG_STD_ACTION CTS-3-POLICY_HA_PROC_FAIL 3-Error Error starting up HA switchover Policy refresh process. A failure has occurred in switchover which has prevented the policy refresh process to be lauched. User should manually refresh policies via the \cts refresh policy\ commad - "Issue command \"cts refresh policy\" and verify policy timers" " are active If timers do not start "LOG_STD_ACTION CTS-3-POLICY_HA_PROC_FAIL 3-Error Error starting up HA switchover Policy refresh process. A failure has occurred in switchover which has prevented the policy refresh process to be lauched. User should manually refresh policies via the \cts refresh policy\ commad - "Issue command \"cts refresh policy\" and verify policy timers" " are active If timers do not start "LOG_STD_ACTION CTS-3-POLICY_INSTALL_FAIL 3-Error An error occurred while trying to program the hardware error code [dec] An error occurred while trying to program the hardware to implement the configured policy. - - CTS-3-POLICY_INSTALL_FAIL 3-Error An error occurred while trying to program the hardware error code [dec] An error occurred while trying to program the hardware to implement the configured policy. - - CTS-3-PORT_AUTHORIZED_FAILED 3-Error Failed to authorize Port for int[chars] Port failed to be authorized on a CTS link - LOG_STD_ACTION CTS-3-PORT_AUTHORIZED_FAILED 3-Error Failed to authorize Port for int[chars] Port failed to be authorized on a CTS link - LOG_STD_ACTION CTS-3-RECEIVE_FAILED 3-Error CTS HA failed to process message recieved from Active device. CTS component Id [dec] message Id [dec] max header size [dec] size [dec] max message size [dec]. CTS HA client on Standby device failed to process checkpoint message. CTS state between the active device and the Standby device is not identical. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-RECEIVE_FAILED 3-Error CTS HA failed to process message recieved from Active device. CTS component Id [dec] message Id [dec] max header size [dec] size [dec] max message size [dec]. CTS HA client on Standby device failed to process checkpoint message. CTS state between the active device and the Standby device is not identical. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-ROOT_CA_STORE_FAIL 3-Error Could not install the CTS trusted-root certificate. An error occcured while installing the CTS trusted-root certificate. This means that CTS cannot validate AAA servers' certifcates received during EAP-FAST exchanges. - - CTS-3-ROOT_CA_STORE_FAIL 3-Error Could not install the CTS trusted-root certificate. An error occcured while installing the CTS trusted-root certificate. This means that CTS cannot validate AAA servers' certifcates received during EAP-FAST exchanges. - - CTS-3-ROOT_CA_STORE_FAIL 3-Error Could not install the CTS trusted-root certificate. An error occcured while installing the CTS trusted-root certificate. This means that CTS cannot validate AAA servers' certifcates received during EAP-FAST exchanges. - - CTS-3-SAP_CIPHER_MISMATCH 3-Error Cipher suite mismatch from peer on int[chars] SAP cipher list mismatch on the interface configured with CTS SAP. Both ends of the CTS SAP link must have matching Cipher list - LOG_STD_ACTION CTS-3-SAP_CIPHER_MISMATCH 3-Error Cipher suite mismatch from peer on int[chars] SAP cipher list mismatch on the interface configured with CTS SAP. Both ends of the CTS SAP link must have matching Cipher list - LOG_STD_ACTION CTS-3-SAP_MANUAL_PMKID_MISMATCH 3-Error PMKID Mismatch on int[chars] received: %08x %08x %08x %08x The PMKID received from peer is different from the expected PMKID - LOG_STD_ACTION CTS-3-SAP_MANUAL_PMKID_MISMATCH 3-Error PMKID Mismatch on int[chars] received: %08x %08x %08x %08x The PMKID received from peer is different from the expected PMKID - LOG_STD_ACTION CTS-3-SAP_NEG_VERSION_MISMATCH 3-Error SAP negotiation error for int[chars] - Received message 2 with higher SAP negotiation error - peer's version higher than local version - LOG_STD_NO_ACTION CTS-3-SAP_NEG_VERSION_MISMATCH 3-Error SAP negotiation error for int[chars] - Received message 2 with higher SAP negotiation error - peer's version higher than local version - LOG_STD_NO_ACTION CTS-3-SAP_NIST_RNG_FAILED 3-Error Failed to obtain random number from CTR-DRBG block for SAP key-counter. Number of consecutive failures[dec] The system failed to obtain a random number for the SAP key counter which causes SAP session failure - LOG_STD_ACTION CTS-3-SAP_NIST_RNG_FAILED 3-Error Failed to obtain random number from CTR-DRBG block for SAP key-counter. Number of consecutive failures[dec] The system failed to obtain a random number for the SAP key counter which causes SAP session failure - LOG_STD_ACTION CTS-3-SEND_FAILED 3-Error CTS HA failed to send checkpoint message. CTS component Id [dec] message Id [dec] header size [dec] max header size [dec] message size [dec] max size [dec]. The CTS HA client failed to send a checkpoint CTS state between the active device and the standby device is not identical. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-SEND_FAILED 3-Error CTS HA failed to send checkpoint message. CTS component Id [dec] message Id [dec] header size [dec] max header size [dec] message size [dec] max size [dec]. The CTS HA client failed to send a checkpoint CTS state between the active device and the standby device is not identical. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-SEND_MSG_TO_CORE_FAILED 3-Error Failed to send msg[dec] to core process An error occcured while CTS attempts to send a message event to the core process - LOG_STD_ACTION CTS-3-SEND_MSG_TO_CORE_FAILED 3-Error Failed to send msg[dec] to core process An error occcured while CTS attempts to send a message event to the core process - LOG_STD_ACTION CTS-3-SEND_NEGO_FAILED 3-Error CTS HA ISSU client failed to send negotiation message. Error: [dec] [chars] The CTS HA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show logging and show checkpoint client" CTS-3-SEND_NEGO_FAILED 3-Error CTS HA ISSU client failed to send negotiation message. Error: [dec] [chars] The CTS HA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show logging and show checkpoint client" CTS-3-SESSION_REGISTRY 3-Error CTS HA ISSU client failed to register session information. Error: [dec] [chars] The CTS HA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show issu capability entries and " "show issu session and " "show issu negotiated capability " CTS-3-SESSION_REGISTRY 3-Error CTS HA ISSU client failed to register session information. Error: [dec] [chars] The CTS HA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. CTS_DDTS_COMPONENT "show issu capability entries and " "show issu session and " "show issu negotiated capability " CTS-3-SESSION_UNREGISTRY 3-Error CTS HA ISSU client failed to unregister session information. Error: [dec] [chars] The CTS HA ISSU client failed to unregister session information. CTS_DDTS_COMPONENT "show issu session and " "show issu negotiated capability " CTS-3-SESSION_UNREGISTRY 3-Error CTS HA ISSU client failed to unregister session information. Error: [dec] [chars] The CTS HA ISSU client failed to unregister session information. CTS_DDTS_COMPONENT "show issu session and " "show issu negotiated capability " CTS-3-SSO_NO_LICENSE 3-Error CTS GCM links are being shut down. Please install a MACSec Encryption License on the new active supervisor http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License. - LOG_STD_DDTS_TAC_DETAILS CTS-3-SSO_NO_LICENSE 3-Error CTS GCM links are being shut down. Please install a MACSec Encryption License on the new active supervisor http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License. - LOG_STD_DDTS_TAC_DETAILS CTS-3-STDBY_NO_LICENSE 3-Error CTS link [chars] may be shut down on switchover: please install MACSec Encryption License on the standby supervisor http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License. - "Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm." CTS-3-STDBY_NO_LICENSE 3-Error CTS link [chars] may be shut down on switchover: please install MACSec Encryption License on the standby supervisor http:/www.cisco.com/go/license A MACSec Encryption License is required to use gcm-encryption on secure links. If the active supervisor has a license but the standby does not then links may run GCM encryption. However on switchover all links running GCM will be shut down because the new active does not have a License. - "Either install a MACSec Encryption License or configure all CTS " "interfaces with cipher modelists that do not include gcm." CTS-3-SXP_CONN_STATE_CHG_OFF 3-Error Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to Off. SXP Connection with the specified instance number changed state. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-3-SXP_CONN_STATE_CHG_OFF 3-Error Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to Off. SXP Connection with the specified instance number changed state. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-3-SXP_LISTENER 3-Error Fail to start global listening socket after TCP process restart. SXP on this device can not accept SXP connection setup request from the remote devices. CTS_DDTS_COMPONENT "Disable and enable SXP feature to see if the global" " listening socket can be restarted." CTS-3-SXP_LISTENER 3-Error Fail to start global listening socket after TCP process restart. SXP on this device can not accept SXP connection setup request from the remote devices. CTS_DDTS_COMPONENT "Disable and enable SXP feature to see if the global" " listening socket can be restarted." CTS-3-SXP_MSG_PARSE 3-Error Connection [chars]<[inet] [inet]> [chars] An error occurred while parsing SXP message. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-SXP_MSG_PARSE 3-Error Connection [chars]<[inet] [inet]> [chars] An error occurred while parsing SXP message. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-3-SXP_NODE_ID_CHG 3-Error SXP Node ID changed from 0x%08X to 0x%08X SXP Node ID changed. CTS_DDTS_COMPONENT "Make sure SXP bindings that use old node ID are removed from the binding database in all SXP nodes before the new node ID is used." CTS-3-SXP_NODE_ID_CHG 3-Error SXP Node ID changed from 0x%08X to 0x%08X SXP Node ID changed. CTS_DDTS_COMPONENT "Make sure SXP bindings that use old node ID are removed from the binding database in all SXP nodes before the new node ID is used." CTS-4-CREATE_SLIST_FAILED 4-Warning [chars]: Failed to create server list. CTS HA failed to create server list while processing server named list sync message. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-CREATE_SLIST_FAILED 4-Warning [chars]: Failed to create server list. CTS HA failed to create server list while processing server named list sync message. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-CREATE_SLIST_FAILED 4-Warning [chars]: Failed to create server list. CTS HA failed to create server list while processing server named list sync message. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-CTS_WARNING 4-Warning [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-CTS_WARNING 4-Warning [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-IFC_RX_AUTHC_FAIL 4-Warning Received AUTHC FAIL for role[chars] int[chars] IFC Received AUTHC FAIL - LOG_STD_ACTION CTS-4-IFC_RX_AUTHC_FAIL 4-Warning Received AUTHC FAIL for role[chars] int[chars] IFC Received AUTHC FAIL - LOG_STD_ACTION CTS-4-IFC_RX_AUTHC_LOGOFF 4-Warning Received AUTHC LOGOFF for peer[chars] role[chars] int[chars] state[chars] - - - CTS-4-IFC_RX_AUTHC_LOGOFF 4-Warning Received AUTHC LOGOFF for peer[chars] role[chars] int[chars] state[chars] - - - CTS-4-IFC_RX_AUTHC_NO_RESP 4-Warning Received AUTHC NO RESP for int[chars] IFC Received AUTHC NO RESP - LOG_STD_ACTION CTS-4-IFC_RX_AUTHC_NO_RESP 4-Warning Received AUTHC NO RESP for int[chars] IFC Received AUTHC NO RESP - LOG_STD_ACTION CTS-4-IFC_RX_AUTHC_REJECT 4-Warning Received AUTHC REJECT for peer[chars] role[chars] int[chars] - - - CTS-4-IFC_RX_AUTHC_REJECT 4-Warning Received AUTHC REJECT for peer[chars] role[chars] int[chars] - - - CTS-4-INT_ERR 4-Warning [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-INT_ERR 4-Warning [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-NO_PROV_SECRET 4-Warning No shared secret available for provisioning PAC from server [inet]. We are unable to provision or reprovision a CTS PAC because we do not have a configured RADIUS shared secret for the server and there are no valid unexpired PACs that can be used to secure the re-provisioning exchange. - - CTS-4-NO_PROV_SECRET 4-Warning No shared secret available for provisioning PAC from server [inet]. We are unable to provision or reprovision a CTS PAC because we do not have a configured RADIUS shared secret for the server and there are no valid unexpired PACs that can be used to secure the re-provisioning exchange. - - CTS-4-NO_PROV_SECRET 4-Warning No shared secret available for provisioning PAC from server [inet]. We are unable to provision or reprovision a CTS PAC because we do not have a configured RADIUS shared secret for the server and there are no valid unexpired PACs that can be used to secure the re-provisioning exchange. - - CTS-4-SLIST_ADD_TO_NAMED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to named list. - - - CTS-4-SLIST_ADD_TO_NAMED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to named list. - - - CTS-4-SLIST_ADD_TO_NAMED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to named list. - - - CTS-4-SLIST_ADD_TO_PREFERRED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to preferred list. - - - CTS-4-SLIST_ADD_TO_PREFERRED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to preferred list. - - - CTS-4-SLIST_ADD_TO_PREFERRED_LIST_FAILED 4-Warning [chars]:tag[chars] - failed to add server[inet]:[dec] to preferred list. - - - CTS-4-SLIST_HANDLER_FAILED 4-Warning [chars]:tag[chars] - failed to locate server list handle. - - - CTS-4-SLIST_HANDLER_FAILED 4-Warning [chars]:tag[chars] - failed to locate server list handle. - - - CTS-4-SLIST_HANDLER_FAILED 4-Warning [chars]:tag[chars] - failed to locate server list handle. - - - CTS-4-SLIST_INVALID_LIST_TYPE 4-Warning [chars]:tag[chars] - invalid server list type[dec]. - - - CTS-4-SLIST_INVALID_LIST_TYPE 4-Warning [chars]:tag[chars] - invalid server list type[dec]. - - - CTS-4-SLIST_INVALID_LIST_TYPE 4-Warning [chars]:tag[chars] - invalid server list type[dec]. - - - CTS-4-SXP_INTERNAL 4-Warning CTS SXP [chars] The CTS SXP system encountered internal failure. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-SXP_INTERNAL 4-Warning CTS SXP [chars] The CTS SXP system encountered internal failure. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-4-SXP_STALE_NODE_ID_CFG 4-Warning Interface configuration is changed may cause adverse affect on SXP functionality Change in interface configuration causing device to hold stale SXP Node ID. CTS_DDTS_COMPONENT "Make sure to re-configure SXP Node ID." CTS-4-SXP_STALE_NODE_ID_CFG 4-Warning Interface configuration is changed may cause adverse affect on SXP functionality Change in interface configuration causing device to hold stale SXP Node ID. CTS_DDTS_COMPONENT "Make sure to re-configure SXP Node ID." CTS-4-SXP_STALE_NODE_ID_GEN 4-Warning Interface configuration is changed may cause adverse affect on SXP functionality Change in interface configuration causing device to hold stale SXP Node ID. CTS_DDTS_COMPONENT "Make sure to disable and then enable SXP global feature." CTS-4-SXP_STALE_NODE_ID_GEN 4-Warning Interface configuration is changed may cause adverse affect on SXP functionality Change in interface configuration causing device to hold stale SXP Node ID. CTS_DDTS_COMPONENT "Make sure to disable and then enable SXP global feature." CTS-5-CTS_NOTICE 5-Notice [chars] Normal but significant conditions CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-5-CTS_NOTICE 5-Notice [chars] Normal but significant conditions CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-5-DOT1X_CONFIG_FAILED 5-Notice Failed to configure dot1x for int[chars] An error occcured while CTS attempts to configure dot1x for a CTS link - LOG_STD_ACTION CTS-5-DOT1X_CONFIG_FAILED 5-Notice Failed to configure dot1x for int[chars] An error occcured while CTS attempts to configure dot1x for a CTS link - LOG_STD_ACTION CTS-5-DOT1X_INIT_FAILED 5-Notice Failed to initialize dot1x for int[chars] An error occcured while CTS attempts to initialize dot1x for a CTS link - LOG_STD_ACTION CTS-5-DOT1X_INIT_FAILED 5-Notice Failed to initialize dot1x for int[chars] An error occcured while CTS attempts to initialize dot1x for a CTS link - LOG_STD_ACTION CTS-5-DOT1X_PAE_FAILED 5-Notice Failed to [chars] dot1x PAE[chars] for int[chars] An error occcured while CTS attempts to start/stop dot1x PAEs for - LOG_STD_ACTION CTS-5-DOT1X_PAE_FAILED 5-Notice Failed to [chars] dot1x PAE[chars] for int[chars] An error occcured while CTS attempts to start/stop dot1x PAEs for - LOG_STD_ACTION CTS-5-ENV_DATA_ACQUISITION_SUCCESS 5-Notice Environment data download success Environment data download completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-ENV_DATA_ACQUISITION_SUCCESS 5-Notice Environment data download success Environment data download completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-ENV_DATA_ACQUISITION_SUCCESS 5-Notice Environment data download success Environment data download completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-ENV_DATA_INSTALL_SUCCESS 5-Notice Environment data installation success Environment data installation completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-ENV_DATA_INSTALL_SUCCESS 5-Notice Environment data installation success Environment data installation completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-ENV_DATA_INSTALL_SUCCESS 5-Notice Environment data installation success Environment data installation completed CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-IFC_DATA_DESC_DECODE_FAILED 5-Notice [chars] failed to decode the data-descriptor - swidb unknown An error occured while the system attempted to decode the data-descriptor in order to obtain the swidb - LOG_STD_ACTION CTS-5-IFC_DATA_DESC_DECODE_FAILED 5-Notice [chars] failed to decode the data-descriptor - swidb unknown An error occured while the system attempted to decode the data-descriptor in order to obtain the swidb - LOG_STD_ACTION CTS-5-PASSWORD_CHANGE_ONE 5-Notice CTS password in the keystore has been renamed \[chars]\. An MSCHAPv2 change-password sequence has been successfully executed and the old password is being renamed for fallback use. This is the first of a 2-part operation. Next the new password will be renamed to become the active password. - - CTS-5-PASSWORD_CHANGE_ONE 5-Notice CTS password in the keystore has been renamed \[chars]\. An MSCHAPv2 change-password sequence has been successfully executed and the old password is being renamed for fallback use. This is the first of a 2-part operation. Next the new password will be renamed to become the active password. - - CTS-5-PASSWORD_CHANGE_ONE 5-Notice CTS password in the keystore has been renamed \[chars]\. An MSCHAPv2 change-password sequence has been successfully executed and the old password is being renamed for fallback use. This is the first of a 2-part operation. Next the new password will be renamed to become the active password. - - CTS-5-PASSWORD_CHANGE_TWO 5-Notice A new CTS password has been installed as \[chars]\ in the keystore. A new CTS password has been installed in the keystore following a successful MSCHAPv2 change-password sequence. The old password has been saved for fallback use. - - CTS-5-PASSWORD_CHANGE_TWO 5-Notice A new CTS password has been installed as \[chars]\ in the keystore. A new CTS password has been installed in the keystore following a successful MSCHAPv2 change-password sequence. The old password has been saved for fallback use. - - CTS-5-PASSWORD_CHANGE_TWO 5-Notice A new CTS password has been installed as \[chars]\ in the keystore. A new CTS password has been installed in the keystore following a successful MSCHAPv2 change-password sequence. The old password has been saved for fallback use. - - CTS-5-POLICY_ACQUISITION_SUCCESS 5-Notice Policy Acquisition success for peer[chars] sgt[chars] - - - CTS-5-POLICY_ACQUISITION_SUCCESS 5-Notice Policy Acquisition success for peer[chars] sgt[chars] - - - CTS-5-POLICY_ACQUISITION_SUCCESS 5-Notice Policy Acquisition success for peer[chars] sgt[chars] - - - CTS-5-ROOT_CA_STORE_DONE 5-Notice A trusted-root certificate to be used for CTS has been installed. A CTS trusted-root certificate was received from a AAA server during an EAP-FAST enrollment. This certificate will be used for validating all AAA servers' certificates received from here on. - - CTS-5-ROOT_CA_STORE_DONE 5-Notice A trusted-root certificate to be used for CTS has been installed. A CTS trusted-root certificate was received from a AAA server during an EAP-FAST enrollment. This certificate will be used for validating all AAA servers' certificates received from here on. - - CTS-5-ROOT_CA_STORE_DONE 5-Notice A trusted-root certificate to be used for CTS has been installed. A CTS trusted-root certificate was received from a AAA server during an EAP-FAST enrollment. This certificate will be used for validating all AAA servers' certificates received from here on. - - CTS-5-SXP_BINDING_ADD 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> added to SXP database. Binding added to the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_ADD 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> added to SXP database. Binding added to the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_CHG 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> changed: old connection instance number:[dec] old sgt:[chars]. Binding changed in the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_CHG 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> changed: old connection instance number:[dec] old sgt:[chars]. Binding changed in the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_CONFLICT 5-Notice Binding [chars]<[chars] [chars]> from peer [inet] change to new sgt [chars] from peer [inet] SXP received conflicting sgt value from different SXP peer for the same IP prefix. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_CONFLICT 5-Notice Binding [chars]<[chars] [chars]> from peer [inet] change to new sgt [chars] from peer [inet] SXP received conflicting sgt value from different SXP peer for the same IP prefix. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_DEL 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> deleted in SXP database. Binding deleted in the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_DEL 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> deleted in SXP database. Binding deleted in the SXP database. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_FWD 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> is forwarded to the peer. SXP forwarded binding to the peer. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_FWD 5-Notice Binding [chars]<[chars] [chars]>-<[inet] [dec]> is forwarded to the peer. SXP forwarded binding to the peer. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_REQ 5-Notice SXP received binding forwarding request [chars] binding [chars]<[chars] [chars]>. SXP received a binding forwarding request. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_REQ 5-Notice SXP received binding forwarding request [chars] binding [chars]<[chars] [chars]>. SXP received a binding forwarding request. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_UPD 5-Notice Binding [chars]<[chars] [chars]> [chars]. Update binding manager. SXP updated binding manager with the binding change. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_BINDING_UPD 5-Notice Binding [chars]<[chars] [chars]> [chars]. Update binding manager. SXP updated binding manager with the binding change. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_KEYCHAIN_CHANGE 5-Notice CTS SXP key-chain changed. The SXP system key-chain has been changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_KEYCHAIN_CHANGE 5-Notice CTS SXP key-chain changed. The SXP system key-chain has been changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_PASSWORD_CHANGE 5-Notice CTS SXP password changed. The SXP system password has been changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_PASSWORD_CHANGE 5-Notice CTS SXP password changed. The SXP system password has been changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_SRCIP_CHG 5-Notice SXP default source IP is changed [inet] --> [inet]. SXP default source IP is changed on this device. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_DFT_SRCIP_CHG 5-Notice SXP default source IP is changed [inet] --> [inet]. SXP default source IP is changed on this device. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_COUNT_REACHED_MAX 5-Notice Reached maximum filter count. Could not add new filter SXP Filter count on the box reached the maximum. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_COUNT_REACHED_MAX 5-Notice Reached maximum filter count. Could not add new filter SXP Filter count on the box reached the maximum. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_COUNT_UPPER_THRESHOLD 5-Notice CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_COUNT_UPPER_THRESHOLD 5-Notice CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_RULE_COUNT_REACHED_MAX 5-Notice Reached maximum filter rules. Could not add new rule in filter [chars] SXP Filter rule count on the box reached the maximum. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_RULE_COUNT_REACHED_MAX 5-Notice Reached maximum filter rules. Could not add new rule in filter [chars] SXP Filter rule count on the box reached the maximum. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_RULE_COUNT_UPPER_THRESHOLD 5-Notice CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_FILTER_RULE_COUNT_UPPER_THRESHOLD 5-Notice CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_STATE_CHANGE 5-Notice CTS SXP [chars] The SXP feature has changed operational state. SXP feature is functioning only when the feature is enabled. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_STATE_CHANGE 5-Notice CTS SXP [chars] The SXP feature has changed operational state. SXP feature is functioning only when the feature is enabled. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_VRF_DEL 5-Notice SXP Connection <[inet] [inet]> configuration in VRF:[chars] is removed. A VRF is removed the connections configured in this VRF should be removed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-5-SXP_VRF_DEL 5-Notice SXP Connection <[inet] [inet]> configuration in VRF:[chars] is removed. A VRF is removed the connections configured in this VRF should be removed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-AUTHZ_CACHE_READ_RESULT 6-Information [chars] cache read from file[chars] [chars] CTS Cache read from cache file done - LOG_STD_ACTION CTS-6-AUTHZ_CACHE_READ_RESULT 6-Information [chars] cache read from file[chars] [chars] CTS Cache read from cache file done - LOG_STD_ACTION CTS-6-AUTHZ_CACHE_READ_RESULT 6-Information [chars] cache read from file[chars] [chars] CTS Cache read from cache file done - LOG_STD_ACTION CTS-6-AUTHZ_CACHED_DATA_EXPIRED 6-Information [chars] cached data expired CTS Cache: Cached data expired - LOG_STD_ACTION CTS-6-AUTHZ_CACHED_DATA_EXPIRED 6-Information [chars] cached data expired CTS Cache: Cached data expired - LOG_STD_ACTION CTS-6-AUTHZ_CACHED_DATA_EXPIRED 6-Information [chars] cached data expired CTS Cache: Cached data expired - LOG_STD_ACTION CTS-6-AUTHZ_ENTRY_ACCESS_POLICY_STATE 6-Information Policy Acquisition in ACCESS state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_ENTRY_ACCESS_POLICY_STATE 6-Information Policy Acquisition in ACCESS state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_ENTRY_ACCESS_POLICY_STATE 6-Information Policy Acquisition in ACCESS state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_ENTRY_COMPLETE_STATE 6-Information Policy Acquisition in COMPLETE state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_ENTRY_COMPLETE_STATE 6-Information Policy Acquisition in COMPLETE state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_ENTRY_COMPLETE_STATE 6-Information Policy Acquisition in COMPLETE state for peer[chars] sgt[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_SUCCESS 6-Information Policy Installation success for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_SUCCESS 6-Information Policy Installation success for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_INSTALL_SUCCESS 6-Information Policy Installation success for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_NO_OP 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_NO_OP 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_NO_OP 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_ATTACH_SUCCESS 6-Information Successfully attached RBM SGACL to RBM policy for sgt[chars]:[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_ATTACH_SUCCESS 6-Information Successfully attached RBM SGACL to RBM policy for sgt[chars]:[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_ATTACH_SUCCESS 6-Information Successfully attached RBM SGACL to RBM policy for sgt[chars]:[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_NO_CHANGE 6-Information Policy refresh for sgt[chars] indicates no change - - - CTS-6-AUTHZ_POLICY_SGACL_NO_CHANGE 6-Information Policy refresh for sgt[chars] indicates no change - - - CTS-6-AUTHZ_POLICY_SGACL_NO_CHANGE 6-Information Policy refresh for sgt[chars] indicates no change - - - CTS-6-AUTHZ_POLICY_SGACL_SUCCESS 6-Information Successfully [chars] SGACL for sgt[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_SUCCESS 6-Information Successfully [chars] SGACL for sgt[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_SUCCESS 6-Information Successfully [chars] SGACL for sgt[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_UPDATE 6-Information SGACL[chars]gen-id[chars] updated to SGACL[chars]gen-id[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_UPDATE 6-Information SGACL[chars]gen-id[chars] updated to SGACL[chars]gen-id[chars] - - - CTS-6-AUTHZ_POLICY_SGACL_UPDATE 6-Information SGACL[chars]gen-id[chars] updated to SGACL[chars]gen-id[chars] - - - CTS-6-AUTHZ_POLICY_UNINSTALL_SUCCESS_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_UNINSTALL_SUCCESS_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_UNINSTALL_SUCCESS_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_UPDATED 6-Information Policy update received for old SGT [chars] new SGT[chars] - - - CTS-6-AUTHZ_POLICY_UPDATED 6-Information Policy update received for old SGT [chars] new SGT[chars] - - - CTS-6-AUTHZ_POLICY_UPDATED 6-Information Policy update received for old SGT [chars] new SGT[chars] - - - CTS-6-AUTHZ_POLICY_WAIT_FOR_RBM_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_WAIT_FOR_RBM_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_POLICY_WAIT_FOR_RBM_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_REFRESH_EXPIRY 6-Information Policy refresh timer[dec] secs has expired for peer[chars] - - - CTS-6-AUTHZ_REFRESH_EXPIRY 6-Information Policy refresh timer[dec] secs has expired for peer[chars] - - - CTS-6-AUTHZ_REFRESH_EXPIRY 6-Information Policy refresh timer[dec] secs has expired for peer[chars] - - - CTS-6-AUTHZ_SM_DESTROY 6-Information Policy Installation state machine destroyed in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_DESTROY 6-Information Policy Installation state machine destroyed in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_DESTROY 6-Information Policy Installation state machine destroyed in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_INIT 6-Information Policy Installation state machine initializing in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_INIT 6-Information Policy Installation state machine initializing in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_INIT 6-Information Policy Installation state machine initializing in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_REINIT 6-Information Policy Installation state machine reinitialization for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_REINIT 6-Information Policy Installation state machine reinitialization for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_REINIT 6-Information Policy Installation state machine reinitialization for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_RETRY_INSTALL 6-Information Policy Installation retry install for int[chars] peer[chars] flag[hec] - - - CTS-6-AUTHZ_SM_RETRY_INSTALL 6-Information Policy Installation retry install for int[chars] peer[chars] flag[hec] - - - CTS-6-AUTHZ_SM_RETRY_INSTALL 6-Information Policy Installation retry install for int[chars] peer[chars] flag[hec] - - - CTS-6-AUTHZ_SM_RUN 6-Information Policy Installation state machine running for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_RUN 6-Information Policy Installation state machine running for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_RUN 6-Information Policy Installation state machine running for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_STOP 6-Information Policy Installation state machine stopped for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_STOP 6-Information Policy Installation state machine stopped for int[chars] peer[chars] - - - CTS-6-AUTHZ_SM_STOP 6-Information Policy Installation state machine stopped for int[chars] peer[chars] - - - CTS-6-AUTHZ_WAIT_POLICY_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_WAIT_POLICY_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-AUTHZ_WAIT_POLICY_STATE 6-Information Policy Installation in [chars] state for int[chars] peer[chars] - - - CTS-6-CRTCL_AUTH_DISABLE 6-Information Critical-Authentication disabled on interface[chars] CTS critical-authentication is disabled on given interface - LOG_STD_NO_ACTION CTS-6-CRTCL_AUTH_DISABLE 6-Information Critical-Authentication disabled on interface[chars] CTS critical-authentication is disabled on given interface - LOG_STD_NO_ACTION CTS-6-CRTCL_AUTH_ENABLE 6-Information Critical-Authentication enabled on interface[chars] CTS critical-autentication is enabled on given interface - LOG_STD_NO_ACTION CTS-6-CRTCL_AUTH_ENABLE 6-Information Critical-Authentication enabled on interface[chars] CTS critical-autentication is enabled on given interface - LOG_STD_NO_ACTION CTS-6-CRTCL_AUTH_REAUTH 6-Information Critical-Authentication starts re-authentication on interface[chars] CTS critical-authentication re-authenticates peer on given interface - LOG_STD_NO_ACTION CTS-6-CRTCL_AUTH_REAUTH 6-Information Critical-Authentication starts re-authentication on interface[chars] CTS critical-authentication re-authenticates peer on given interface - LOG_STD_NO_ACTION CTS-6-CTS_INFO 6-Information [chars] Informational messages CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-CTS_INFO 6-Information [chars] Informational messages CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-DOT1X_FORCE_PORT_AUTHORIZED_SUCCESS 6-Information Successfully forced dot1x port authorized for int[chars] Port has been put to FORCE AUTHORIZED on a CTS link - LOG_STD_ACTION CTS-6-DOT1X_FORCE_PORT_AUTHORIZED_SUCCESS 6-Information Successfully forced dot1x port authorized for int[chars] Port has been put to FORCE AUTHORIZED on a CTS link - LOG_STD_ACTION CTS-6-DOT1X_PAE_CONFIG 6-Information [chars] dot1x PAE[chars] for int[chars] The interface has been configured for dot1x PAEs - LOG_STD_ACTION CTS-6-DOT1X_PAE_CONFIG 6-Information [chars] dot1x PAE[chars] for int[chars] The interface has been configured for dot1x PAEs - LOG_STD_ACTION CTS-6-DOT1X_PEER_LOGOFF 6-Information DOT1X reported peer LOGOFF message on int[chars] DOT1X reported peer LOGOFF message - LOG_STD_NO_ACTION CTS-6-DOT1X_PEER_LOGOFF 6-Information DOT1X reported peer LOGOFF message on int[chars] DOT1X reported peer LOGOFF message - LOG_STD_NO_ACTION CTS-6-DOT1X_PEER_NO_RESP 6-Information DOT1X reported peer NO RESPONSE message on int[chars] DOT1X reported peer NO RESPONSE message - LOG_STD_NO_ACTION CTS-6-DOT1X_PEER_NO_RESP 6-Information DOT1X reported peer NO RESPONSE message on int[chars] DOT1X reported peer NO RESPONSE message - LOG_STD_NO_ACTION CTS-6-ENV_DATA_ASSESS_STATE 6-Information Environment Data Download in assess state Environment data download in assess state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_ASSESS_STATE 6-Information Environment Data Download in assess state Environment data download in assess state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_ASSESS_STATE 6-Information Environment Data Download in assess state Environment data download in assess state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_CLEAR_SUCCESS 6-Information Environment data successfully cleared. Environment data successfully cleared. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_CLEAR_SUCCESS 6-Information Environment data successfully cleared. Environment data successfully cleared. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_COA_REQUEST 6-Information Command [chars]=[chars]-[chars] A Change of Authorization request command is received for update-env-data - LOG_STD_ACTION CTS-6-ENV_DATA_COA_REQUEST 6-Information Command [chars]=[chars]-[chars] A Change of Authorization request command is received for update-env-data - LOG_STD_ACTION CTS-6-ENV_DATA_REFRESH_TIMER 6-Information Time to refresh environment data ENV data refresh timer - LOG_STD_NO_ACTION CTS-6-ENV_DATA_REFRESH_TIMER 6-Information Time to refresh environment data ENV data refresh timer - LOG_STD_NO_ACTION CTS-6-ENV_DATA_REFRESH_TIMER 6-Information Time to refresh environment data ENV data refresh timer - LOG_STD_NO_ACTION CTS-6-ENV_DATA_START_STATE 6-Information Environment Data Download in start state Environment data download in start state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_START_STATE 6-Information Environment Data Download in start state Environment data download in start state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_START_STATE 6-Information Environment Data Download in start state Environment data download in start state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_WAIT_RESP_STATE 6-Information Environment Data Download in wait response state Environment data download in wait response state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_WAIT_RESP_STATE 6-Information Environment Data Download in wait response state Environment data download in wait response state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-ENV_DATA_WAIT_RESP_STATE 6-Information Environment Data Download in wait response state Environment data download in wait response state CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-FIPS_SW_POST_PASS 6-Information Software crypto POST PASS All power-up software crypto algorithmic known answer tests have passed. - LOG_STD_NO_ACTION CTS-6-FIPS_SW_POST_PASS 6-Information Software crypto POST PASS All power-up software crypto algorithmic known answer tests have passed. - LOG_STD_NO_ACTION CTS-6-HA_ENV_DATA_STALE 6-Information CTS HA environment-data sync failed. Old environment-data is stale. The CTS HA environment-data sync to standby failed. CTS environment download could be in progress and old data is stale. - LOG_STD_NO_ACTION CTS-6-HA_ENV_DATA_STALE 6-Information CTS HA environment-data sync failed. Old environment-data is stale. The CTS HA environment-data sync to standby failed. CTS environment download could be in progress and old data is stale. - LOG_STD_NO_ACTION CTS-6-IFC_AUTHC_STATE 6-Information Interface Controller in AUTHENTICATION state for int[chars] IFC Entering Authentication State - LOG_STD_NO_ACTION CTS-6-IFC_AUTHC_STATE 6-Information Interface Controller in AUTHENTICATION state for int[chars] IFC Entering Authentication State - LOG_STD_NO_ACTION CTS-6-IFC_AUTHORIZE_STATE 6-Information Interface Controller in AUTHORIZATION state [chars] for int[chars] peer[chars] IFC Entering Authorization State - LOG_STD_NO_ACTION CTS-6-IFC_AUTHORIZE_STATE 6-Information Interface Controller in AUTHORIZATION state [chars] for int[chars] peer[chars] IFC Entering Authorization State - LOG_STD_NO_ACTION CTS-6-IFC_CACHE_APPLIED 6-Information Cache data applied for int[chars] Inform the user that the CTS link is brought up using cache data - LOG_STD_ACTION CTS-6-IFC_CACHE_APPLIED 6-Information Cache data applied for int[chars] Inform the user that the CTS link is brought up using cache data - LOG_STD_ACTION CTS-6-IFC_DISCONNECT_STATE 6-Information Interface Controller in DISCONNECT state for int[chars] IFC Entering DISCONNECT State - LOG_STD_NO_ACTION CTS-6-IFC_DISCONNECT_STATE 6-Information Interface Controller in DISCONNECT state for int[chars] IFC Entering DISCONNECT State - LOG_STD_NO_ACTION CTS-6-IFC_HELD_STATE 6-Information Interface Controller in HELD state for int[chars] IFC Entering HELD State - LOG_STD_NO_ACTION CTS-6-IFC_HELD_STATE 6-Information Interface Controller in HELD state for int[chars] IFC Entering HELD State - LOG_STD_NO_ACTION CTS-6-IFC_INIT_STATE 6-Information Interface Controller in INITIALIZATION state for int[chars] IFC Entering INIT State - LOG_STD_NO_ACTION CTS-6-IFC_INIT_STATE 6-Information Interface Controller in INITIALIZATION state for int[chars] IFC Entering INIT State - LOG_STD_NO_ACTION CTS-6-IFC_LICENSE_ERR_STATE 6-Information Interface Controller in LICENSE ERR state for int[chars] IFC Entering LICENSE ERR State - LOG_STD_NO_ACTION CTS-6-IFC_LICENSE_ERR_STATE 6-Information Interface Controller in LICENSE ERR state for int[chars] IFC Entering LICENSE ERR State - LOG_STD_NO_ACTION CTS-6-IFC_OPEN_STATE 6-Information Interface Controller in OPEN state for int[chars] IFC Entering OPEN State - LOG_STD_NO_ACTION CTS-6-IFC_OPEN_STATE 6-Information Interface Controller in OPEN state for int[chars] IFC Entering OPEN State - LOG_STD_NO_ACTION CTS-6-IFC_RX_AUTHC_SUCCESS 6-Information Received AUTHC SUCCESS for peer[chars] role[chars] sgt[chars] int[chars] - - - CTS-6-IFC_RX_AUTHC_SUCCESS 6-Information Received AUTHC SUCCESS for peer[chars] role[chars] sgt[chars] int[chars] - - - CTS-6-IFC_SAP_STATE 6-Information Interface Controller in SAP NEGOTIATION state for int[chars] IFC Entering SAP State - LOG_STD_NO_ACTION CTS-6-IFC_SAP_STATE 6-Information Interface Controller in SAP NEGOTIATION state for int[chars] IFC Entering SAP State - LOG_STD_NO_ACTION CTS-6-IFC_SM_STATE 6-Information Interface Controller state machine started for int[chars] IFC Started - LOG_STD_NO_ACTION CTS-6-IFC_SM_STATE 6-Information Interface Controller state machine started for int[chars] IFC Started - LOG_STD_NO_ACTION CTS-6-INCOMPAT 6-Information CTS HA ISSU client negotiation results incompatible The CTS HA ISSU client message version is not compatible on Active and Standby. No CTS data will be synced to Standby in this case CTS_DDTS_COMPONENT "show issu capability entries and " "show issu session and " "show issu negotiated version " CTS-6-INCOMPAT 6-Information CTS HA ISSU client negotiation results incompatible The CTS HA ISSU client message version is not compatible on Active and Standby. No CTS data will be synced to Standby in this case CTS_DDTS_COMPONENT "show issu capability entries and " "show issu session and " "show issu negotiated version " CTS-6-PAC_PROVI_SUCCESS 6-Information PAC Provisioning succeeded for [inet] A-ID=[chars] PAC Provisioning succeeded - LOG_STD_NO_ACTION CTS-6-PAC_PROVI_SUCCESS 6-Information PAC Provisioning succeeded for [inet] A-ID=[chars] PAC Provisioning succeeded - LOG_STD_NO_ACTION CTS-6-PAC_PROVI_SUCCESS 6-Information PAC Provisioning succeeded for [inet] A-ID=[chars] PAC Provisioning succeeded - LOG_STD_NO_ACTION CTS-6-POLICY_COA_DONE 6-Information Command [chars]=[chars] completed A Change of Authorization request has been serviced - LOG_STD_ACTION CTS-6-POLICY_COA_DONE 6-Information Command [chars]=[chars] completed A Change of Authorization request has been serviced - LOG_STD_ACTION CTS-6-POLICY_COA_DONE 6-Information Command [chars]=[chars] completed A Change of Authorization request has been serviced - LOG_STD_ACTION CTS-6-POLICY_COA_NO_ACTION 6-Information Command [chars]=[chars] has no change A Change of Authorization request has been received but no action was taken due to the system is already in possession of the requested data - LOG_STD_ACTION CTS-6-POLICY_COA_NO_ACTION 6-Information Command [chars]=[chars] has no change A Change of Authorization request has been received but no action was taken due to the system is already in possession of the requested data - LOG_STD_ACTION CTS-6-POLICY_COA_NO_ACTION 6-Information Command [chars]=[chars] has no change A Change of Authorization request has been received but no action was taken due to the system is already in possession of the requested data - LOG_STD_ACTION CTS-6-POLICY_COA_NO_SESSION 6-Information Command [chars]=[chars] has no session associated A Change of Authorization request has been received for infomration that the system is not in possession of - LOG_STD_ACTION CTS-6-POLICY_COA_NO_SESSION 6-Information Command [chars]=[chars] has no session associated A Change of Authorization request has been received for infomration that the system is not in possession of - LOG_STD_ACTION CTS-6-POLICY_COA_NO_SESSION 6-Information Command [chars]=[chars] has no session associated A Change of Authorization request has been received for infomration that the system is not in possession of - LOG_STD_ACTION CTS-6-POLICY_COA_RBACL_REQUEST 6-Information Command [chars]=[chars]-[chars] A Change of Authorization request command is received for update-rbacl - LOG_STD_ACTION CTS-6-POLICY_COA_RBACL_REQUEST 6-Information Command [chars]=[chars]-[chars] A Change of Authorization request command is received for update-rbacl - LOG_STD_ACTION CTS-6-POLICY_COA_RBACL_REQUEST 6-Information Command [chars]=[chars]-[chars] A Change of Authorization request command is received for update-rbacl - LOG_STD_ACTION CTS-6-POLICY_COA_SGT_REQUEST 6-Information Command [chars]=[chars] A Change of Authorization request command is received for update-sgt - LOG_STD_ACTION CTS-6-POLICY_COA_SGT_REQUEST 6-Information Command [chars]=[chars] A Change of Authorization request command is received for update-sgt - LOG_STD_ACTION CTS-6-POLICY_COA_SGT_REQUEST 6-Information Command [chars]=[chars] A Change of Authorization request command is received for update-sgt - LOG_STD_ACTION CTS-6-POLICY_RBACL_MONITOR_ALL 6-Information Failed to set monitor all for dynamic policies An error occurred while CTS attempted to set monitor flag for all dynamic installed policies. - LOG_STD_ACTION CTS-6-POLICY_RBACL_MONITOR_ALL 6-Information Failed to set monitor all for dynamic policies An error occurred while CTS attempted to set monitor flag for all dynamic installed policies. - LOG_STD_ACTION CTS-6-POLICY_RBACL_MONITOR_ALL 6-Information Failed to set monitor all for dynamic policies An error occurred while CTS attempted to set monitor flag for all dynamic installed policies. - LOG_STD_ACTION CTS-6-PORT_AUTHORIZED_SUCCESS 6-Information Port authorized for int[chars] Port has been authorized on a CTS link - LOG_STD_ACTION CTS-6-PORT_AUTHORIZED_SUCCESS 6-Information Port authorized for int[chars] Port has been authorized on a CTS link - LOG_STD_ACTION CTS-6-PORT_UNAUTHORIZED 6-Information Port unauthorized for int[chars] Port has been unauthorized on a CTS link - LOG_STD_ACTION CTS-6-PORT_UNAUTHORIZED 6-Information Port unauthorized for int[chars] Port has been unauthorized on a CTS link - LOG_STD_ACTION CTS-6-REAUTH_TIMER_EXPIRED 6-Information Timer expired on int[chars] REAUTH Timer expired - LOG_STD_NO_ACTION CTS-6-REAUTH_TIMER_EXPIRED 6-Information Timer expired on int[chars] REAUTH Timer expired - LOG_STD_NO_ACTION CTS-6-REAUTH_TIMER_EXPIRED 6-Information Timer expired on int[chars] REAUTH Timer expired - LOG_STD_NO_ACTION CTS-6-REAUTHENTICATION_PERIOD_CHANGED 6-Information Reauthentication period is changed to [dec] Reauthentication period is changed while applying configuration change to the link object - LOG_STD_NO_ACTION CTS-6-REAUTHENTICATION_PERIOD_CHANGED 6-Information Reauthentication period is changed to [dec] Reauthentication period is changed while applying configuration change to the link object - LOG_STD_NO_ACTION CTS-6-SAP_DOT1X_PMKID_MISMATCH 6-Information PMKID Mismatch on int[chars] received: %08x %08x %08x %08x The PMKID received from peer is different from the expected PMKID - LOG_STD_ACTION CTS-6-SAP_DOT1X_PMKID_MISMATCH 6-Information PMKID Mismatch on int[chars] received: %08x %08x %08x %08x The PMKID received from peer is different from the expected PMKID - LOG_STD_ACTION CTS-6-SAP_NEG_DOWNREV 6-Information SAP negotiation for int[chars] switching from version[dec] to peer's version[dec] - - - CTS-6-SAP_NEG_DOWNREV 6-Information SAP negotiation for int[chars] switching from version[dec] to peer's version[dec] - - - CTS-6-SAP_NEG_DOWNREV_RESTART 6-Information SAP negotiation for int[chars] - Received message 2 with lower version[dec] SAP negotiation switching to peer's lower version restarting message 1 - LOG_STD_NO_ACTION CTS-6-SAP_NEG_DOWNREV_RESTART 6-Information SAP negotiation for int[chars] - Received message 2 with lower version[dec] SAP negotiation switching to peer's lower version restarting message 1 - LOG_STD_NO_ACTION CTS-6-SAP_REKEY_TIMER_EXPIRED 6-Information SAP Rekey Timer Expired for interface[chars] after [dec] SAP Rekey Timer Expired. - LOG_STD_NO_ACTION CTS-6-SAP_REKEY_TIMER_EXPIRED 6-Information SAP Rekey Timer Expired for interface[chars] after [dec] SAP Rekey Timer Expired. - LOG_STD_NO_ACTION CTS-6-SAP_SUCCESS 6-Information SAP Success for int[chars] selected cipher[chars] version[dec] - - - CTS-6-SAP_SUCCESS 6-Information SAP Success for int[chars] selected cipher[chars] version[dec] - - - CTS-6-SXP_BINDING_ERR 6-Information Binding [chars]<[chars] [chars]>-<[inet] [dec]> [chars] SXP binding update error. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-6-SXP_BINDING_ERR 6-Information Binding [chars]<[chars] [chars]>-<[inet] [dec]> [chars] SXP binding update error. CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-6-SXP_CONFIG 6-Information Connection [chars]<[inet][inet]> [chars] A SXP configuration error occurred. The connection can not be setup correctly. CTS_DDTS_COMPONENT "Ensure that the connection configure on both ends" " have the matched mode IP addresses." CTS-6-SXP_CONFIG 6-Information Connection [chars]<[inet][inet]> [chars] A SXP configuration error occurred. The connection can not be setup correctly. CTS_DDTS_COMPONENT "Ensure that the connection configure on both ends" " have the matched mode IP addresses." CTS-6-SXP_CONN_STATE_CHG 6-Information Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to [chars]. SXP Connection with the specified instance number changed state. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_CONN_STATE_CHG 6-Information Connection [chars]<[inet] [inet]>-[dec] state changed from [chars] to [chars]. SXP Connection with the specified instance number changed state. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_COUNT_CHG 6-Information CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_COUNT_CHG 6-Information CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_COUNT_LOWER_THRESHOLD 6-Information SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box dropped below lower threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_COUNT_LOWER_THRESHOLD 6-Information SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec] SXP Filter count on the box dropped below lower threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_RULE_COUNT_CHG 6-Information CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_RULE_COUNT_CHG 6-Information CTS SXP filter rules exceed [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box changed. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_RULE_COUNT_LOWER_THRESHOLD 6-Information SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_FILTER_RULE_COUNT_LOWER_THRESHOLD 6-Information SXP filter rules dropped below [[dec]%%] threshold. Reached count of [dec] out of [dec] in filter [chars]. SXP Filter rule count on the box exceeded upper threshold. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_PEER_IP 6-Information Peer IP address [chars] [inet] belongs to this device. - - - CTS-6-SXP_PEER_IP 6-Information Peer IP address [chars] [inet] belongs to this device. - - - CTS-6-SXP_SRC_IP 6-Information Source IP address [chars] [inet] does not belong to this device. - - - CTS-6-SXP_SRC_IP 6-Information Source IP address [chars] [inet] does not belong to this device. - - - CTS-6-SXP_TIMER_START 6-Information Connection [chars]<[inet] [inet]> [chars] timer started. The specified SXP timer started. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_TIMER_START 6-Information Connection [chars]<[inet] [inet]> [chars] timer started. The specified SXP timer started. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_TIMER_STOP 6-Information Connection [chars]<[inet] [inet]> [chars] timer stopped. The specified SXP timer stopped. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-6-SXP_TIMER_STOP 6-Information Connection [chars]<[inet] [inet]> [chars] timer stopped. The specified SXP timer stopped. CTS_DDTS_COMPONENT LOG_STD_NO_ACTION CTS-7-AUTHZ_ENTRY_HDL_SENDL_FAILED 7-Debug Error retrieving the authorization entry handle Error retrieving the authorization entry handle - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_HDL_SENDL_FAILED 7-Debug Error retrieving the authorization entry handle Error retrieving the authorization entry handle - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_HDL_SENDL_FAILED 7-Debug Error retrieving the authorization entry handle Error retrieving the authorization entry handle - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_PENDING_REQUEST 7-Debug RADIUS request to acquire policy for peer[chars] sgt[chars] was not RADIUS request to acquire policy for peer was not sent due to pending request in progress - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_PENDING_REQUEST 7-Debug RADIUS request to acquire policy for peer[chars] sgt[chars] was not RADIUS request to acquire policy for peer was not sent due to pending request in progress - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_PENDING_REQUEST 7-Debug RADIUS request to acquire policy for peer[chars] sgt[chars] was not RADIUS request to acquire policy for peer was not sent due to pending request in progress - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_WAIT_FOR_ACE 7-Debug Policy Acquisition for peer[chars] sgt[chars] is waiting for the Policy acquisition for peer is waiting for the ACE download complete - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_WAIT_FOR_ACE 7-Debug Policy Acquisition for peer[chars] sgt[chars] is waiting for the Policy acquisition for peer is waiting for the ACE download complete - LOG_STD_ACTION CTS-7-AUTHZ_ENTRY_WAIT_FOR_ACE 7-Debug Policy Acquisition for peer[chars] sgt[chars] is waiting for the Policy acquisition for peer is waiting for the ACE download complete - LOG_STD_ACTION CTS-7-AUTHZ_PEER_POL_DEL 7-Debug Deleting peer policy for peer[chars] sgt[chars] - - - CTS-7-AUTHZ_PEER_POL_DEL 7-Debug Deleting peer policy for peer[chars] sgt[chars] - - - CTS-7-AUTHZ_PEER_POL_DEL 7-Debug Deleting peer policy for peer[chars] sgt[chars] - - - CTS-7-AUTHZ_PEER_POL_DEL_PENDING 7-Debug Pending peer policy delete for peer[chars] sgt[chars] due to Pending peer policy delete for peer due to outstanding SGACL install/uninstall - LOG_STD_ACTION CTS-7-AUTHZ_PEER_POL_DEL_PENDING 7-Debug Pending peer policy delete for peer[chars] sgt[chars] due to Pending peer policy delete for peer due to outstanding SGACL install/uninstall - LOG_STD_ACTION CTS-7-AUTHZ_PEER_POL_DEL_PENDING 7-Debug Pending peer policy delete for peer[chars] sgt[chars] due to Pending peer policy delete for peer due to outstanding SGACL install/uninstall - LOG_STD_ACTION CTS-7-CTS_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CTS-7-CTS_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] CTS_INTERNAL_ERROR CTS_DDTS_COMPONENT LOG_STD_ACTION CUBE-3-LICENSING 3-Error [chars] CUBE Licensing Enforcement ipipgw LOG_STD_SH_TECH_ACTION CUBE-3-LICENSING 3-Error [chars] CUBE Licensing Enforcement ipipgw LOG_STD_SH_TECH_ACTION CUBE-5-LICENSE_INFO 5-Notice [chars] Periodic entitlement status ipipgw LOG_STD_ACTION CUBE-5-LICENSE_INFO 5-Notice [chars] Periodic entitlement status ipipgw LOG_STD_ACTION CVAC-2-INIT_FAILED 2-Critical Virtual appliance configuration cannot occur: [chars] The system was unable to even attempt to apply virtual appliance configuration for the given reason. virt-infra LOG_STD_SH_TECH_ACTION CVAC-3-CONFIG_ERROR 3-Error [dec] errors while applying configs generated from file [chars]. Out of the generated virtual appliance configuration commands the given number of commands were rejected by the IOSd parser. The indicated log file will describe exactly which commands were rejected as will any accompanying CVAC-4-CLI_FAILURE messages in this log. virt-infra "Consult the indicated log file for details of the " "errors that were encountered. Also inspect the " "current running-config and startup-config of the " "router using the show " "running-config and show " "startup-config commands in order to " "confirm that the configuration is valid." CVAC-3-FILE_ERROR 3-Error Could not [chars] file [chars]: [chars] The system was unable to perform the indicated operation on the indicated file for the indicated reason virt-infra "Make sure the given disk is correctly formatted " "and has sufficient free space available." CVAC-3-XML_ERROR 3-Error Error while parsing XML from file [chars]: error '[chars]' element '[chars]' attribute '[chars]' explanation '[chars]'. File will be saved to [chars] The contents of the given file were not correct XML and as a result XML parsing aborted due to the given reason. No new configuration was applied to the router from this file. virt-infra "Investigate the contents of the saved file " "to determine the cause of the reported error and " "if possible fix the file contents restore it to " "its original location and reload to re-process it. " LOG_STD_RECUR_ACTION CVAC-4-CLI_FAILURE 4-Warning Configuration command failure: '[chars]' was rejected The indicated IOSd configuration command generated by the CVAC subsystem was rejected by the IOSd CLI. Look for a subsequent CVAC-3-CONFIG_ERROR log message which will contain a reference to a logfile containing more information about this failure. virt-infra "Inspect the log file to determine why the command " "was rejected and how to correct it. If necessary " "manually re-issue the corrected command." CVAC-4-CONFIG_DONE 4-Warning Configuration generated from file [chars] was applied and saved to NVRAM. See [chars] for more details. The generated configuration was applied and the resulting system configuration has been saved to the startup-config in NVRAM. The indicated logfile may contain additional information. virt-infra LOG_STD_NO_ACTION CVAC-4-FILE_IGNORED 4-Warning Configuration file [chars] is ignored: [chars] The indicated configuration file was ignored and not used for configuration for the given reason. virt-infra LOG_STD_NO_ACTION CVAC-4-PROPERTY_IGNORED 4-Warning Property key '[chars]' value '[chars]' ignored: [chars] The indicated XML configuration property was ignored for the indicated reason virt-infra "If the property was not applied due to an invalid " "key or value either change these attributes to " CVAC-4-WRITE_FAIL 4-Warning Configuration generated from file [chars] was applied but could not be saved to NVRAM. See [chars] for more details. The generated configuration was applied but the resulting system configuration was not saved to the startup-config in NVRAM. The indicated logfile may contain additional information. virt-infra "Issue the write memory command on the IOS CLI" CVAC-5-XML_PARSED 5-Notice [dec] lines of configuration generated from file [chars] The indicated file was successfully parsed to generate IOSd configuration commands. The generated configs have not yet been applied to the system. virt-infra LOG_STD_NO_ACTION CVLA_CLIENT-4-CVLA_MEMORY_BOUNDARY_TOUCH_CLEAR 4-Warning CVLA memory utilization has declined below its threshold memory is available for [chars]. After CVLA was in memory shortage memory utilization has declined below its threshold New traffic flows will be opened properly qfp-cvla LOG_STD_ACTION CVLA_CLIENT-4-CVLA_MEMORY_BOUNDARY_TOUCH_WARN 4-Warning CVLA reached maximum configured memory utilization. Can't allocate more memory for [chars]. Because of CVLA memory shortage new flows may not be opened properly qfp-cvla LOG_STD_ACTION CVLA_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_CLEAR 4-Warning System free memory has increased above its lower watermark memory is available for [chars]. After system memory was in shortage free memory has increased above its lower watermark New traffic flows will be opened properly qfp-cvla LOG_STD_ACTION CVLA_CLIENT-4-SYS_FREE_MEMORY_LOW_WATERMARK_TOUCH_WARN 4-Warning System free memory has reached its lower watermark. Can't allocate more memory for [chars]. Because of system memory shortage new flows may not be opened properly qfp-cvla LOG_STD_ACTION CVLA-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the CVLA infra failed. This will cause the infra to not function. qfp-cvla "This is normally a software issue. " "The consequences are that the CVLA infra will not function. " LOG_STD_ACTION CVLA-3-FEAUTE_HANDLE_INVALID 3-Error Invalid handle magic 0x[hec] for handle %p Internal error Feautre handle contains invalid magic cpp-ucode LOG_STD_ACTION CVLA-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper CVLA software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as infra activation. qfp-cvla "This is normally a software issue. " LOG_STD_RECUR_ACTION CVLA-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper CVLA software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as infra activation. qfp-cvla "This is normally a software issue. " LOG_STD_RECUR_ACTION CWAN_CHOC_DS0-3-CDBFAIL 3-Error Port [dec]/[dec] - fail to create a SONET controller data structure The software resource can't be allocated for this hardware osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-3-CFG_BAD_PARA 3-Error [chars]: invalid config parameter [chars] Configuration parameter is invalid osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-3-IFCONFIG_ERR 3-Error config error on port [dec]/[dec][chars] cmd [dec] [chars] A configuration command sent from the system to a linecard failed osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-3-PORTFAIL 3-Error Port [dec]/[dec] - fail to create a port instance data structure The software resource can't be allocated for this hardware osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-3-RMCTRLR_UNKNOWN 3-Error Slot [dec] - Unknown linecard type [dec] removed This hardware can't be recognized by this version of software. osm-choc-ds0 "Check software version. Make sure the software supports the hardware." CWAN_CHOC_DS0-3-T1CFG_CCBERROR 3-Error CCB command error cmd [dec] arg [dec] on T1 [dec]/[dec]/[dec] A command sent from the system to a linecard failed osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-3-UNKNOWN_MIB_TYPE 3-Error Unknown MIB type [dec] from slot [dec] Draco received unknown communication message from linecard osm-choc-ds0 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DS0-3-UNKNOWNCTRLR 3-Error Slot [dec] - Unknown linecard type [dec] This hardware can't be recognized by this version of software. osm-choc-ds0 "Check software version. Make sure the software supports the hardware." CWAN_CHOC_DS0-3-VCCFG_CCBERROR 3-Error CCB command error cmd [dec] arg [dec] on port [dec]/[dec] channel [dec] A command sent from the system to a linecard failed osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-4-ALLOCFAIL 4-Warning Interface [dec]/[dec] allocation failed: [chars] required resources unavailable. osm-choc-ds0 "Either upgrade system memory or reconfigure memory usage." CWAN_CHOC_DS0-4-CORRUPT 4-Warning [chars] information seems to be corrupted bad value =[dec] wrong parameters detected internally osm-choc-ds0 "This is only a debug warning message. The unexpected value is\n\ discarded." CWAN_CHOC_DS0-4-IFCONFIG 4-Warning [chars] config error [dec] lc delay:[dec] ms: [chars] RP received configuration error from linecard. osm-choc-ds0 "Reconfigure or shut/no shut the error channel." CWAN_CHOC_DS0-4-LCLOCK_FAIL 4-Warning Interface [chars] failed to acquire semaphore for LC access: [chars] Other process locked the semaphore for too long. osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-4-PROV_FAIL 4-Warning Interface [chars] provisioning ch[dec] failed: [chars] provisioning conflict or resource shortage osm-choc-ds0 "workaround: under 'controller sonet' do 'no channelized' followed\n\ by 'channelized' twice. If problem persists do a\n\ 'show controller sonet /' and\n\ 'show controller {pos/serial} /:' then contact\n\ cisco technical support representative." CWAN_CHOC_DS0-4-UNPROV_FAIL 4-Warning Interface [chars] unprovisioning failed: [chars] Linecard failed to response unprovisioning command. osm-choc-ds0 LOG_STD_ACTION CWAN_CHOC_DS0-4-UNSUP 4-Warning Slot [dec]: Unknown [chars] [dec] This value is not recognized by this version of software. osm-choc-ds0 "Check linecard version. Normally this is harmless but worth contacting\n\ cisco technical support representative." CWAN_CHOC_DS0-4-WRONG_LL 4-Warning %.16s received wrong loveletter : type=[dec] length=[dec] wrong parameters detected internally osm-choc-ds0 "This is only a debug warning message. The unexpected messages from\n\ linecard is harmlessly discarded." CWAN_CHOC_DS0-5-LOOPSTATUS 5-Notice [chars] [chars] A configurable loopback status. - LOG_STD_NO_ACTION CWAN_CHOC_DSX-3-ENQUEUE_FAIL 3-Error [chars] cmd enqueue failure osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-INVALID_SUBR_HWIDB 3-Error Invalid Subrate hwidb on T3 [dec]/[dec] invalid subrate hwidb osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-NODESTROYSUBBLOCK 3-Error The [chars] subblock named [chars] was not removed A software error has occured this message is displayed when\n\ IDB subblocks cannot be removed. osm-ct3 for CT3 osm-t3e3 for T3/E3 \n\ osm-choc-ds0 for CHOC-12/CHOC-3 LOG_STD_ACTION CWAN_CHOC_DSX-3-NULLDS3MIBTABLE 3-Error Null DS3 MIB table snmp_if_index [dec] System cannot find the DS3 MIB table pointer osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-PROCESS_ERROR 3-Error process error - [chars] process encountered fatal error osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-PROCESS_FAIL 3-Error process creation failed for [chars] process creation failed for handling cmd osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-SEND_DRIVER_READY 3-Error send driver ready msg failed for [dec] IPC message failure osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-T1CFG_ERROR 3-Error T1 [dec]/[dec]/[dec] config command error cmd [dec] arg [dec] retval [dec] A command sent from the system to a linecard failed osm-ct3 LOG_STD_ACTION CWAN_CHOC_DSX-3-T3CFG_ERROR 3-Error T3 [dec]/[dec] config command error cmd [dec] arg [dec] retval [dec] A command sent from the system to a linecard failed osm-ct3 LOG_STD_ACTION CWAN_CHOC_DSX-3-UNKNOWN_CTRLR 3-Error Slot [dec] - Unknown linecard type [dec] This hardware can't be recognized by this version of software. osm-ct3 "Check software version. Make sure the software supports the hardware." CWAN_CHOC_DSX-3-VC_CONFIG_ERR 3-Error [chars] T1 [dec] channel group [dec] of T3 [dec]/[dec] unsuccessful error code [dec] channel configuration error osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC_DSX-3-VCCFG_ERROR 3-Error VC [dec]/[dec]:[dec] config command error cmd [dec] arg [dec] retval [dec] A command sent from the system to a linecard failed osm-ct3 for CT3 osm-choc-ds0 for CHOC-12 LOG_STD_ACTION CWAN_CHOC_DSX-5-DEF_SUBRATE 5-Notice [chars] [chars] Remote subrate configuration changed osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Inform the network operator that subrate configuration changed by\n\ remote end" CWAN_CHOC_DSX-5-UNKNOWN_EVENT 5-Notice [chars] Unexpected event received by the process osm-ct3 for CT3 osm-t3e3 for T3/E3 osm-choc-ds0 for CHOC-12/CHOC-3 "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWAN_CHOC-4-ALLOCFAIL 4-Warning Interface [dec]/[dec] allocation failed: [chars] required resources unavailable. osm-choc-ds3 "Either upgrade system memory or reconfigure memory usage." CWAN_CHOC-4-CORRUPT 4-Warning [chars] information seems to be corrupted bad value =[dec] wrong parameters detected internally osm-choc-ds3 "This is only a debug warning message. The unexpected value is\n\ discarded." CWAN_CHOC-4-IFCONFIG 4-Warning [chars] config error [dec] lc delay:[dec] ms: [chars] RP received configuration error from linecard. osm-choc-ds3 "Reconfigure or shut/no shut the error channel." CWAN_CHOC-4-LCCFG_MISMATCH 4-Warning LC needs reboot due to config mismatch on [chars] rc=[dec] RP detects LC's channel provisioning mismatching start-config osm-choc-ds3 "reset linecard: hw-module module reset" CWAN_CHOC-4-LCLOCK_FAIL 4-Warning Interface [chars] failed to acquire semaphore for LC access: [chars] Other process locked the semaphore for too long. osm-choc-ds3 LOG_STD_ACTION CWAN_CHOC-4-PROV_FAIL 4-Warning Interface [chars] provisioning ch[dec] failed: [chars] provisioning conflict or resource shortage osm-choc-ds3 "workaround: under 'controller sonet' do 'no channelized' followed\n\ by 'channelized' twice. If problem persists do a\n\ 'show controller sonet /' and\n\ 'show controller {pos/serial} /:' then contact\n\ cisco technical support representative." CWAN_CHOC-4-UNPROV_FAIL 4-Warning Interface [chars] unprovisioning failed: [chars] Linecard failed to response unprovisioning command. osm-choc-ds3 LOG_STD_ACTION CWAN_CHOC-4-UNSUP 4-Warning Slot [dec]: Unknown [chars] [dec] This value is not recognized by this version of software. osm-choc-ds3 "Check linecard version. Normally this is harmless but worth contacting\n\ cisco technical support representative." CWAN_CHOC-4-WRONG_LL 4-Warning %.16s received wrong loveletter : type=[dec] length=[dec] wrong parameters detected internally osm-choc-ds3 "This is only a debug warning message. The unexpected messages from\n\ linecard is harmlessly discarded." CWAN_CHOC-6-LCDRIVER 6-Information OIR failed: slot [dec] linecard not responding to initial query OIR insertion aborted due to failing to contact lc osm-choc-ds3 LOG_STD_ACTION CWAN_CHOC-6-WRONG_GULF 6-Information [chars] hardware version gulf v[dec] does not support OC-12 or OC-48 Early version of hw asic GULF2.0 and below has bugs in\n\ rx fifo depth which can not handle oc-12 or oc-48 rate.\n\ Either limiting channel provisioning or upgrading hw osm-choc-ds3 "Limit channel provisioning to DS3 and/or OC3" CWAN_CONTAINER_ACCESS-5-CWAN_NO_CONTAINER 5-Notice Associated container interface does not exist for [chars] The container interface no longer exists for access interface. c7600-bb LOG_STD_NO_ACTION CWAN_CONTAINER_ACCESS-5-CWAN_VRF_MISMATCH 5-Notice VRF of [chars] access does not match with [chars] VRF of access interface does not match with that of associated container interface. Either container interface is deleted or VRF of container interface is changed c7600-bb LOG_STD_NO_ACTION CWAN_HA-3-CCB_INIT_ERROR 3-Error Failed to initialize CCB list for slot [dec]. The High Availability component for WAN modules failed to properly initialize state information for the specified slot. c7600-ha LOG_STD_ACTION CWAN_HA-3-IFCFG_CMD_NOT_UNIQUE 3-Error More than one command registered for unique-key generator for interface configuration command [dec]. The High Availability component for WAN modules is unable to properly synchronize state information for the current configuration due to a conflict in command identifiers. c7600-ha LOG_STD_ACTION CWAN_HA-3-IFCFG_INIT_ERROR 3-Error Failed to initialize Interface Configuration list for slot [dec]/[dec]. The High Availability component for WAN modules failed to properly initialize state information for the specified slot. c7600-ha LOG_STD_ACTION CWAN_HA-3-IFCFG_NO_UNIQUE_KEY 3-Error No unique-key generator registered for interface configuration command [dec]. The High Availability component for WAN modules is unable to properly synchronize state information for the current configuration. c7600-ha LOG_STD_ACTION CWAN_HA-4-CCB_PLAYBACK_ERROR 4-Warning CCB playback failed for slot [dec]. The High Availability component for WAN modules failed to synchronize some new state information for the specified slot. c7600-ha "Reload the standby supervisor module to force a fresh bulk " "synchronization. If this error recurs " LOG_STD_ACTION CWAN_HA-4-CCB_RECORD_ERROR 4-Warning CCB record failed for slot [dec]. The High Availability component for WAN modules failed to record some new state information for the specified slot. c7600-ha LOG_STD_ACTION CWAN_HA-4-IFCFG_DFLT_LIST_ERROR 4-Warning For Interface Configuration command [dec] default retval list search resulted 0x[hec] for slot [dec]/[dec] The High Availability component for WAN modules failed to synchronize some new state information for the specified slot. c7600-ha show platform redundancy \ if-config default-retvals CWAN_HA-4-IFCFG_PLAYBACK_ERROR 4-Warning Interface Configuration command [dec] playback failed for slot [dec]/[dec]. The High Availability component for WAN modules failed to synchronize some new state information for the specified slot. c7600-ha LOG_STD_ACTION CWAN_HA-4-IFCFG_RECORD_ERROR 4-Warning Interface Configuration command [dec] record failed for slot [dec]/[dec]. The High Availability component for WAN modules failed to record some new state information for the specified slot. c7600-ha LOG_STD_ACTION CWAN_HA-4-IFEVENT_BULKSYNCFAIL 4-Warning [chars] ifevent: [dec] error: [dec] Failed CWAN if-event bulk sync. c7600-ha LOG_STD_NO_ACTION CWAN_HA-4-IFEVENT_INCRSYNCFAIL 4-Warning [chars] for ifevent: [dec] with error: [dec] Failed CWAN if-event incremental sync. c7600-ha LOG_STD_NO_ACTION CWAN_HA-4-IFEVENT_UNEXPECTED_BULKTYPE 4-Warning Unexpected value for bulk sync type [dec] received. Received a unexpected type in bulk sync message. c7600-ha LOG_STD_NO_ACTION CWAN_HA-4-LTLSYNCFAIL 4-Warning Failed to sync LTL data during [chars] for [chars] [dec]: slot=[dec]slotunit=[dec] if_num=[dec] to standby vlan=[dec]hash=[dec]ltl=[dec]\n Some LTL data did not sync correctly from active to standby RP\n c7600-ha LOG_STD_ACTION CWAN_HA-4-NOSRPBULKSYNC 4-Warning Failed to [chars] SRP bulk data slot=[dec] intf=[dec] type=[dec] ret code [dec]\n Some SRP-related state information failed to sync correctly from the active RP to the standby RP during the HA bulk-synchronization phase. c7600-ha LOG_STD_ACTION CWAN_HA-4-NOSRPSYNC 4-Warning Failed to sync SRP packet slot=[dec]intf=[dec] to standby Some SRP-related state information failed to sync correctly from the active RP to the standby RP when the configuration changed. c7600-ha LOG_STD_ACTION CWAN_HA-4-SRPSYNC 4-Warning Slot [dec]: [chars]\n An error occured while syncing SRP states from active RP to standby RP. c7600-ha LOG_STD_ACTION CWAN_RP-1-OVERRIDE_MAC_INVALID 1-Alert [chars] has invalid override-mac-address. The user has issued an override-mac-address that does not match the mac address of the MSFC. This can occur if the config has been moved to new hardware or the mac-address command has been used on another interface. while the system automatically corrects this the config needs to be adjusted. cwan "Modify the override-mac-address command in the config." CWAN_RP-1-TOO_MANY_VRF 1-Alert Slot [dec] can not support all the VRFs configured! A non-Enhanced OSM card has been inserted into a router with more than 511 IP VRFs already configured. This router cannot support more than 511 IP VRFs if there is at least one non-Enhanced OSM in the system. cwan "Replace the inserted non-Enhanced OSM with " "an Enhanced OSM or decrease the number of " "IP VRFs to 511 or fewer." CWAN_RP-3-BAD_IFCOMTYPE 3-Error Bad ifcom message type=[dec] A WAN module passed down a message that the RP software\n\ was not prepared to handle. - LOG_STD_ACTION CWAN_RP-3-BOOTFAIL 3-Error The WAN module in slot [dec]/[dec] failed to boot The WAN module in the slot indicated in the error messages \n\ failed to boot and will be reset. - LOG_STD_RECUR_ACTION CWAN_RP-3-CHANGE_POSEIDON_NEGOTIATION 3-Error Unable to change negotiation. Failed to send message to\n\ slot [dec] port [dec]! MSFC2 failed to send message to change negotiation to\n\ OSM-4GE-WAN-GBIC - LOG_STD_ACTION CWAN_RP-3-CWAN_IFCOM_RMI 3-Error Cwan ifcom RMI failure - [chars][dec] The CWAN IFCOM RMI Registration. c7600-env LOG_STD_NO_ACTION CWAN_RP-3-ERROR 3-Error NULL This message can take many forms. It provides information about a\n\ software error. - LOG_STD_ACTION CWAN_RP-3-FAILED_CONFIG 3-Error Failed to send line card config message [chars] for slot [dec] port [dec] The RP could not send the specified configuration message to the line card osm-gigwan LOG_STD_ACTION CWAN_RP-3-FOREVER 3-Error cmd [dec] to [chars] slot [dec]/[dec] took [dec] usecs done [hec] A CCB command from the RP to a WAN module took longer than expected. - LOG_STD_ACTION CWAN_RP-3-GBIC_INSERTED 3-Error GBIC media type [dec] inserted in [chars] A GBIC was inserted in the interface. cwan LOG_STD_NO_ACTION CWAN_RP-3-GBIC_REMOVED 3-Error GBIC removed from [chars] The GBIC was removed from the interface. cwan LOG_STD_NO_ACTION CWAN_RP-3-HV_ALLOCFAIL 3-Error [chars]: Failed to allocate a VLAN: [chars] VLAN allocation failed for the stated reason. - "First power down any unused linecards. " "Next delete any unused interfaces/subinterfaces and " "any unused L2 VLANs from the VLAN database. " "Then wait for >3 minutes and retry." CWAN_RP-3-IFCFG_CMD_NOT_OWNER 3-Error Process '[chars]' waiting for interface configuration command 0x[hec] to A process on the RP sent an configuration command to the slot specified in the error message and a different process waited for the result. This could cause incorrect line card configuration states. c7600-ha LOG_STD_ACTION CWAN_RP-3-IFCFG_FOREVER 3-Error to [chars] slot [dec]/[dec] took [dec] usecs ret_val %lu A interface config command from the RP to a WAN module took \n\ longer than expected. - LOG_STD_ACTION CWAN_RP-3-IFCONFIG_ERR 3-Error Interface config failed on port [dec]/[dec] cmd [dec] retval [dec] A configuration command sent from the system to a linecard failed osm-ct3 LOG_STD_ACTION CWAN_RP-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The RP failed to allocate a buffer for communication with a\n\ WAN module. - LOG_STD_ACTION CWAN_RP-3-IPCPORTFAIL 3-Error Failed to open IPC port '[chars]' [chars] with error [chars] The RP failed to open a port for communication with a WAN\n\ module. - LOG_STD_ACTION CWAN_RP-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The RP failed to send a message to a WAN module. - LOG_STD_ACTION CWAN_RP-3-KEEPFAIL 3-Error The WAN module in slot [dec]/[dec] is not responding to keepalives The WAN module was either reset or has crashed and will be reset. - LOG_STD_RECUR_ACTION CWAN_RP-3-LC_CRASHINFO 3-Error [chars] copied onto RP bootflash The WAN module has crashed and the crashinfo file has been\n\ copied onto the RP bootflash. The crashinfo filename indicates the\n\ module's slot. The file can be viewed using the\n\ more command. - LOG_STD_ACTION CWAN_RP-3-LC_CRASHINFO_BLOCKED 3-Error Duplicate crashinfo upload from slot [dec]/[dec] blocked The WAN module has crashed and the crashinfo was not saved because\n\ the WAN module has already crashed recently. - LOG_STD_ACTION CWAN_RP-3-LC_CRASHINFO_CORRUPT 3-Error Verification of crashinfo from slot [dec]/[dec] failed The WAN module has crashed and verification of the crashinfo it\n\ sent failed. The crashinfo has not been saved to RP bootflash. - LOG_STD_ACTION CWAN_RP-3-LC_CRASHINFO_ERR 3-Error Unexpected error while receiving crashinfo from slot [dec]/[dec] The WAN module has crashed and an unexpected error occured while\n\ the crashinfo was being copied onto RP bootflash. - LOG_STD_ACTION CWAN_RP-3-LC_CRASHINFO_IFSERR 3-Error Error [chars] [chars]: [chars] [dec] The WAN module has crashed and an error occured while trying to\n\ access the RP's bootflash to save the crashinfo. - LOG_STD_ACTION CWAN_RP-3-LC_CRASHINFO_NOSPACE 3-Error Not enough space on RP bootflash for crashinfo from slot [dec]/[dec] [dec] bytes needed [dec] available The WAN module has crashed and there is not enough space on the RP\n\ bootflash to store the crashinfo. - "Free up space on the RP's bootflash by using the\n\ delete and squeeze\n\ commands." CWAN_RP-3-LCLOG_BADSEV 3-Error Invalid message severity from slot [dec]/[dec]: [dec] The WAN module passed down a logger message with an invalid\n\ severity level that the RP could not handle. - LOG_STD_ACTION CWAN_RP-3-MODULE_TYPE 3-Error cannot find FCI for module type [dec] in slot [dec] An internal software error occurred while the system was detecting the module type for the module in the specified slot. The operation of the module will be affected. osm-basecard LOG_STD_ACTION CWAN_RP-3-OIRTWICE 3-Error Slot [dec] OIR insertion/removal not paired up: [chars] An internal OIR-related error occured for the specified WAN\n\ module. cwtlc LOG_STD_ACTION CWAN_RP-3-POWER_CYCLE 3-Error Power cycling WAN module in slot [dec]/[dec]. [chars] The WAN module is being power cycled. - LOG_STD_NO_ACTION CWAN_RP-3-POWER_CYCLE_IMMINENT 3-Error The WAN module in slot [dec]/[dec] will be power cycled in [dec] seconds. The WAN module in the slot specified in the error message \n\ will be power cycled in the amount of time specified in the error \n\ message - LOG_STD_NO_ACTION CWAN_RP-3-PROCMSG 3-Error Process msg send failed for process[dec] Process message send failed. cwan LOG_STD_ACTION CWAN_RP-3-RESET_FAIL 3-Error The WAN module in slot [dec] failed even after several resets The WAN module in the slot specified in the error \n\ message did not boot successfully even after multiple \n\ attempts. - LOG_STD_RECUR_ACTION CWAN_RP-3-SCPALLOCFAIL 3-Error Failed to allocate SCP packet [chars] The RP failed to allocate a packet for communication with other\n\ slots in the chassis. - LOG_STD_RECUR_ACTION CWAN_RP-3-SLOTCACHE_SYNTAX 3-Error Error [chars]! The RP failed to parse the slot configuration string. - LOG_STD_ACTION CWAN_RP-3-UPGRADE_ERROR 3-Error Slot [dec]: The ROMMON upgrade failed to complete. An error occurred during the upgrade process. vpn-sm "If the module reloads successfully please check " "the file and try again otherwise please contact " "your Cisco technical support representative." CWAN_RP-3-WAN_BRIDGING_CFG_EXCD 3-Error The number of VPLS/EoMPLS/Bridging/QinQ VCs exceeded the maximum[dec] Review the configuration guidelines for the features that are being configured and reduce the number of VPLS EoMPLS Bridging to the number that is supported by the platform. osm-bridge - CWAN_RP-4-CONFIG_MISMATCH 4-Warning \n\nIrreconcilable Configuration difference between Active & Standby Supervisors due to OIR/Config Event for [dec]/[dec] -> Reloading Standby Supervisor to synchronize the configuration.\n\n Unexpected configuration difference between Supervisors. c7600-ha "None. This is expected behavior." CWAN_RP-4-EMPTY_CWANBAYS 4-Warning FLEXWAN in slot [dec] is empty. Please remove the Flexwan or insert it with atleast one PA The FLEXWAN in the specified slot does not contain any Port Adapters. - "The FLEXWAN should be removed as this is an unsupported configuration" CWAN_RP-4-IFCFG_CMD_TIMEOUT 4-Warning Interface configuration command 0x[hec] to slot [dec]/[dec] timed out The RP sent an configuration command to the slot specified in the error message and received no confirmation for the command. c7600-ha LOG_STD_ACTION CWAN_RP-4-INCR_CFG_SYNC_FAIL 4-Warning 7600 incremental running-config sync for [[dec]/[dec]] failed - [chars][dec] The specified 7600 incremental running-config sync failed c7600-ha "Power cycle the redundant supervisor" CWAN_RP-4-INVALID_UNIT 4-Warning Invalid 7600 Unit: [[dec]/[dec]]. The specified 7600 slot/cpu beyonds the Chassis's limit. c7600-ha "Power cycle the redundant supervisor" CWAN_RP-4-IPCFAILED 4-Warning IPC failed to send RPC message to WAN module The RP failed to send an RPC message via IPC to a WAN module. cwan LOG_STD_NO_ACTION CWAN_RP-4-LCLOG_TOOLONG 4-Warning Message too long from slot [dec]/[dec]: [dec] bytes The WAN module passed down a logger message that is too long for\n\ the RP to handle. - LOG_STD_ACTION CWAN_RP-4-LL_UNKNOWN 4-Warning Unknown linecard message: type [dec] [chars] Mismatch version between RP and LC or internal message format mismatch cwan LOG_STD_NO_ACTION CWAN_RP-4-MODULE_CONFIG_MISSING 4-Warning configuration not available/not matching in startup-config for slot [dec] Some information regarding the configuration of the module in the specified slot is missing. Any configuration in the startup-config for the interfaces will not be applied. If the module in the specified slot is a FlexWAN the missing configuration information is details of the Port Adapters in the FlexWAN module. This information is missing from the SLOTCACHE ROMMON variable. osm-basecard - CWAN_RP-4-SEMAHOG 4-Warning Process [dec] [chars] hogging [chars]! calling proc [dec] [chars] - - - CWAN_RP-6-ADF_FILE 6-Information Slot [dec]: Using VPN-SM Upgrade File: \[chars]\ Booting specified upgrade image for VPN Services Module. - LOG_STD_NO_ACTION CWAN_RP-6-AUX_FILE 6-Information Slot [dec]: Found VPN-SM Firmware in File: \[chars]\ The file specified in the message was found and will be loaded by the VPN Services Module instead of the bundled image. - LOG_STD_NO_ACTION CWAN_RP-6-CARDRECONCILE 6-Information Module type changed on slot [dec]/[dec] from [dec] to [dec] The WAN module has booted and it has been detected that it is\n\ of a different type to the WAN module that was previously in\n\ this slot. - LOG_STD_NO_ACTION CWAN_RP-6-CARDRELOAD 6-Information Module reloaded on slot [dec]/[dec] The WAN module has booted. - LOG_STD_NO_ACTION CWAN_RP-6-COREDUMP_ENABLED 6-Information No heartbeat or keepalive resets will occur for slot [dec] since coredump has been enabled The module in the slot has crashed and is configured to generate a coredump file. The module will not be reset due to heartbeat and keepalive failures to ensure the coredump file generation is not prematurely terminated. c7600-env LOG_STD_NO_ACTION CWAN_RP-6-IMAGE_UPGRADE 6-Information Bootflash image upgrade [chars] for slot [dec]/[dec][chars] The bootflash image on the WAN module has been or is being\n\ automatically upgraded. - LOG_STD_NO_ACTION CWAN_RP-6-LC_PRESENT 6-Information [chars] in slot [dec] A WAN module was detected by the hardware. - LOG_STD_NO_ACTION CWAN_RP-6-LC_RESET 6-Information The RP is reloaded resetting slot [dec] is necessary. Please ignore errors if any till the linecard comes up. If the system is running Catalyst operating system software on the supervisor engine and Cisco IOS software on the MSFC the WAN line cards that power up before the RP powers up will be reset automatically. cwpa LOG_STD_NO_ACTION CWAN_RP-6-NOPWRISSU 6-Information Spa inserted in [chars] powered down because ISSU is in progress The Spa insertion detected during ISSU upgrade process. It will be acted upon completion of the ISSU process. - LOG_STD_NO_ACTION CWAN_RP-6-OUT_OF_RESOURCE 6-Information [chars] configuration has exceeded available internal resources. The resources required for configuration are no longer available. They may have been acquired by another application. osm-mpb "If the requested resources have not been allocated " "to another application call your technical support representative " "for further assistance." CWAN_RP-6-OVERRIDE 6-Information Slot [dec]: ...Overriding Intrinsic VPN-SM Firmware. Specified image will be used instead of bundled image. - LOG_STD_NO_ACTION CWAN_RP-6-PLAT_AVL_DEL_FAILED 6-Information Platform AVL delete failed for PPPoE session due to wrong slot id [dec] Deletion of session related information from the AVL tree failed because the slot number used to index it is wrong c7600-bb LOG_STD_NO_ACTION CWAN_RP-6-QUIESCE_FAIL 6-Information Quiesce failed for slot [dec]/[dec] The RP failed to contact the WAN module during failover.\n\ The WAN module will be reset. - LOG_STD_NO_ACTION CWAN_RP-6-SESS_LIMITS_CHASSIS 6-Information Exceeded max number of sessions supported. \nSupported limit 32000/chassis Total number of subscriber sessions on this chassis exceeded the allowed limits. The supported limit is 32000 sessions per chassis c7600-bb "Avoid bringing up more number of sessions " "than the supported limit" CWAN_RP-6-SESS_LIMITS_ES_PLUS 6-Information Exceeded max number of sessions supported on ES+ LC in slot [dec]. \nSupported limit 16000/ES+ Total number of subscriber sessions on ES+ line card exceeded the allowed limits. The supported limit is 16000 sessions per ES+ c7600-bb "Avoid bringing up more number of sessions " "than the supported limit" CWAN_RP-6-SESS_LIMITS_PORT_GROUP 6-Information Exceeded max number of sessions supported on port-group Gig[dec]/[dec] to Gig[dec]/[dec].\nSupported limit 4000/port-group on ES+ LC Total number of subscriber sessions on a single port-group in ES+ exceeded the allowed limits. The supported limit is 4000 sessions per port-group c7600-bb "Rearrange the subscribers on ES+ in such a way " "maximum number of sessions supported in a port-group is 4000." CWAN_RP-6-SESS_LIMITS_SIP400 6-Information Exceeded max number of sessions supported on SIP400 LC in slot [dec]. \nSupported limit 8000/SIP400 Total number of subscriber sessions on SIP400 line card exceeded the allowed limits. The supported limits is 8000 sessions per SIP400 c7600-bb "Avoid bringing up more number of sessions " "than the supported limit" CWAN_RP-6-SESS_LIMITS_TEN_GIG_PORT 6-Information Exceeded max number of sessions supported on port Te[dec]/[dec]. \nSupported limit 8000/port on a Ten Gig port on ES+ LC. Total number of subscriber sessions on a single Ten Gig port in ES+ exceeded the allowed limits. The supported limit is 8000 sessions per Ten Gig port. c7600-bb "Rearrange the subscribers on ES+ in such a way that " "maximum number of sessions per Ten Gig port is 8000" CWAN_RP-6-UNQUIESCE_FAIL 6-Information Unquiesce failed for slot [dec]/[dec]. Error = [dec] The RP failed to unquiesce the WAN module. \n\ The WAN module will be reset. - show diagbus and show ipc status CWAN_RP-6-UPGRADE_COMPLETE 6-Information Slot [dec]: ROMMON upgrade complete. Reset the card for the changes to take effect. The ROMMON upgrade has completed successfully. The card must be reloaded for the changes to take effect - LOG_STD_NO_ACTION CWAN_RP-7-SLOTCACHE_CARDTYPE 7-Debug parsed slot [dec] fci_type [dec] Information parsed from the slot configuration string by the RP. - LOG_STD_NO_ACTION CWAN_RP-7-SLOTCACHE_PATYPE 7-Debug Bay [chars] has type [dec] ports[hec] Information parsed from the slot configuration string by the RP. - LOG_STD_NO_ACTION CWAN_SPA-3-CREATION_FAILURE 3-Error slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec]. Failed to create a SPA object. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-DIAG_CONFIG 3-Error [chars] did not complete [dec]/[dec] An error has occured during diagnostic test. c7600-field-diag LOG_STD_SH_TECH_ACTION CWAN_SPA-3-FAILURE 3-Error [chars]: SPA failure - cause: [chars] [hex] recovery action: [chars] [dec] The SPA failed for the specified reason FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-INTR_THROTTLE 3-Error Interface [chars] MAC interrupt was throttled.\n\ Reenabling MAC interrupts via one sec spa process MAC interrupt burst has occurred on one of the interfaces on the link daughtercard. The error message indicates that a throttling mechanism has been applied to this port to avoid any operational damage that could be provoked by this event. The cause for this problem could be bad transceiver highly frenquent flapping optical signals or mismatched path signals e.g. receiving 10GBASE-W signal on 10GE LAN interface etc. c7600-esm-20 "Check the interface configuration and received signal characteristics. " "Also verify the XFP transceiver and receive signal path to determine the " "If this message recurs " LOG_STD_ACTION CWAN_SPA-3-INVALID_DATA_INSTANCE 3-Error interface type [chars] slot [dec] port [dec] vc [dec] : [chars] Data required to support the interface is not available. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-INVALID_IF_INDEX 3-Error index= [dec] cardType=0x[hec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec] Index for the interface is not valid. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-INVALID_INDX_RANGE 3-Error index1= [dec] index2= [dec] maxIndex= [dec] Invalid index range. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-MEM_ALLOC_ERROR 3-Error [chars] Memory allocation error. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-NULL_ATM_DB 3-Error Unable to create ATM DB for [chars] Data required to support the interface is not available. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-NULL_SPA_PTR 3-Error - Pointer to a SPA object is NULL. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-NULL_VFT 3-Error [chars] virtual function table is not initialized. spaType=0x[hec] A required function table is not initialized FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-NULL_VFUNC 3-Error [chars] vector is not initialized. spaType=0x[hec] A required function vector is not initialized FIX-ME LOG_STD_SH_TECH_ACTION CWAN_SPA-3-POWER_CYCLE 3-Error [chars] occurred on Shared Port Adapter [dec]/[dec] An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled msc-200-ha LOG_STD_SH_TECH_ACTION CWAN_SPA-3-SPA_CREATION_FAILURE 3-Error slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec]. Failed to create a SPA object. FIX-ME LOG_STD_SH_TECH_ACTION CWAN_T3E3-3-IFCONFIG_ERR 3-Error Interface config error on T3 port [dec]/[dec] cmd [dec] retval [dec] A configuration command sent from the system to a linecard failed osm-t3e3 LOG_STD_ACTION CWANLC_ATM-3-CMDERR 3-Error [chars]: [chars] IPC command fails cause: 0x%04x The ATM RP driver experienced IPC command error. cwtlc "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC_ATM-3-IPC_ERROR 3-Error [chars]: IPC command \[chars]\ failure due to \[chars]\ The SPA ATM RP driver experienced IPC command error. spa-atm-all "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC_ATM-3-NOVPSPACE 3-Error [chars]: out of VP space for VPI [dec] Out of VPs on the SAR. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC_ATM-3-VCCLOSEFAIL 3-Error [chars]: Failed to remove VC [dec]/[dec] cause [dec] Attempt to remove VC on the linecard failed. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC_ATM-3-VPCLOSEFAIL 3-Error [chars]: Failed to remove VP [dec] cause [dec] Attempt to remove VP on the linecard failed. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC_ATM-4-CLOSEPEND 4-Warning [chars]: The TX SAR is currently freeing internal buffers previously allocated for the identical channel id. The execution of the current command is delayed. The TX SAR has taken longer than expected to free its internal buffers. - LOG_STD_NO_ACTION CWANLC_ATM-4-MISMATCH_VCENCAP 4-Warning [chars]: Cannot mix VC encapsulation types in multipoint interfaces This ATM card only allows VC encapsulations of the same type on the main interface or multipoint subinterfaces - "Reconfigure the ATM interface with matching VC encapsulations" CWANLC_ATM-4-SEMHOG 4-Warning [chars]: Process [dec] [chars] hogging semaphore -- called by process [dec] [chars] The named process has held the resource semaphore longer than\n\ expected. - LOG_STD_NO_ACTION CWANLC_ATM-4-UNSUP 4-Warning [chars]: unsupported feature: [chars] This feature is not supported by Draco ATM RP. cwtlc "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWANLC-2-PCIERROR 2-Critical Fatal PCI Error [chars] seen on PCI Bus [dec] A Fatal PCI Error was detected on the PCI bus. Most likely it is a hardware problem. - "Call your technical support representative for " "assistance if this message persists." CWANLC-3-CWANLC_EARL_VERSION_NOTICE 3-Error CWAN receives mismatch Earl version notification. New Earl[dec] vs Earl[dec] The RP has determined via an SCP find operation that the version of the EARL switching engine on the line card has changed. This message occurs during switchover operation. The version of the EARL switching engine is specified in the message text. - LOG_STD_ACTION CWANLC-3-FATAL 3-Error [chars] The Optical Services Module line card has encountered a fatal error. - LOG_STD_ACTION CWANLC-3-FPD_INCOMPATIBLE 3-Error FPD ID=[dec] image in this FPD package is for revision [dec].x boards. It is incompatible with current board revision of [dec].[dec] This FPD package does not contain images that are compatible with the current board revision. c7600-sip-common "Perform the FPD upgrade operation with a newer version of FPD " "image package that is compatible with the running Cisco IOS " "software. Consult with the FPD image package section of the " "Cisco IOS software release note to confirm if your board " "revision is supported for a particular release." CWANLC-3-HWREVREADFAIL 3-Error Failed to retrieve h/w version from EEPROM The Linecard failed to read the hardware version from the CPU eeprom. - LOG_STD_ACTION CWANLC-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The Linecard failed to allocate a buffer for communication with the Route Processor Draco. - "Copy the error message exactly as it appears and report it to your " "technical support representative." CWANLC-3-IPCPORT 3-Error Failed to [chars] IPC port '[chars]' error [chars] The Linecard failed to create a port for communication with the Route Processor Draco. - "Copy the error message exactly as it appears and report it to your " "technical support representative." CWANLC-3-IPCPORTFAIL 3-Error Failed to open IPC port '[chars]' [chars] The Linecard failed to open a port for communication with the Route Processor Draco. - "Copy the error message exactly as it appears and report it to your " "technical support representative." CWANLC-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The Linecard failed to send a message to the Route Processor Draco. - "Copy the error message exactly as it appears and report it to your " "technical support representative." CWANLC-3-LTL_NOPPEPORTMAP 3-Error Failed to retrieve default port mapping for packet processor [dec] The linecard software initialization was not completed correctly - LOG_STD_ACTION CWANLC-3-TVPN_NOMEM 3-Error Failed to start vpn not enough memory The OSM card could not start VPN due to a memory exhaustion - "Reduce other system activity to ease memory demands. " "If conditions warrant upgrade to a larger memory " "configuration. If this message recurs "LOG_STD_ACTION CWANLC-4-LOGMSGTOOBIG 4-Warning Logger message length exceeds max [dec] bytes The Linecard attempted to send a large message to the Route Processor Draco. - LOG_STD_ACTION CWANLC-5-IPCPENDING 5-Notice Too many messages [dec] in IPC pending queue The IPC pending queue is growing. Will soon deplete the IPC header cache and the IO buffers - LOG_STD_ACTION CWANLC-5-NOSCPPING 5-Notice Linecard has not sent SCP PING responses for too long SCP ping mechanism is used by RP/SP processors to monitor if the linecard executing IOS is in a healthy state. This SCP ping response has not been sent by the line card for long time now - the line card has exported its context information to the RP and may be powercycled. The exported context is available in the output of 'show diag' cwpa "Save the 'show diag' output generated and contact your " "technical support representative if the line card is reset" CWANLC-6-BUSSTALL 6-Information Constellation BUS Stall detected This message indicates that a stall was detected on the Constellation Bus probably due to some OIR activity on the Bus. - "No action needed Informational." CWANLC-6-BUSSTALLCLEAR 6-Information Constellation BUS Stall cleared This message indicates that a stall was cleared on the Constellation Bus. - "No action needed Informational." CWANLC-6-LONGSTALL 6-Information Long bus stall [dec] ms check for improperly seated cards This message indicates that a stall was detected but the backplane stall was longer than expected. - "Make sure all cards are firmly seated. If the " "problem reoccurs it may indicate a hardware failure." CWMP_DOWNLOAD-5-CONFIG_FAILURE 5-Notice CWMP download: config apply operation failed [chars] The configuration apply operation with CWMP DOWNLOAD RPC\n\method is failed. - "No action required." CWMP_DOWNLOAD-5-CONFIG_SUCCESS 5-Notice CWMP download: config file successfully downloaded and applied [chars] The configuration apply operation with CWMP DOWNLOAD RPC\n\method is success. - "No action required." CWPA-2-BAD_HWVERS 2-Critical Unable to determine board hardware version The line card software cannot read the line card hardware version. This condition indicates a hardware error. cwpa LOG_STD_ACTION CWPA-2-PA_VOLFAIL 2-Critical Port adapter [dec]V failed Reloading flexwan The line card has encountered an error involving power delivery to the line card. Likely causes for this error are an environmental condition an overtemperature condition or inconsistent voltage to the line card. cwpa "Check the input voltage and temperature of the line card. " LOG_STD_RECUR_ACTION CWPA-2-PAOIR 2-Critical Port adapter OIR not supported reloading An OIR operation occurred on the port adapters of the specified line card. OIR operations are not supported on the port adapter. This error has caused the line card to crash and reload. cwpa "Do not attempt an OIR operation on the port adapters of the specified " "line card." CWPA-2-WHICH_INT 2-Critical Unexpected [chars] interrupt INT status = 0x[hec] The line card specified in the error message has encountered an unexpected interrupt. cwpa LOG_STD_ACTION CWPA-3-BAD_IFCOMTYPE 3-Error Bad ifcom message type=[dec] - - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-BADMALUCMD 3-Error Unsupported MALU command [dec] arg=[hex] pascb=[hex] - - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-CMDNOPASCB 3-Error PASCB Null for command [dec] arg=[hex] - - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-DIAGFAIL 3-Error Failed to handle diag [chars] [dec] The FlexWAN line card failed to execute diag command. Further details are specified in the text that is displayed on the console or in the system log. cwpa "Copy the error message exactly as it appears and report it to your " "technical support representative." CWPA-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The FlexWAN line card failed to allocate a buffer for communication with the Route Processor Draco. - "Copy the error message exactly as it appears and report it to your " "technical support representative." CWPA-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The FlexWAN line card failed to send a message to the\n\ Route Processor Draco. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-LVLTRTOOBIG 3-Error Loveletter length exceeds max [dec] bytes The FlexWAN line card attempted to send a large message to the\n\ Route Processor Draco. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-NODISPATCH 3-Error Dispatch vector Null cmd=[dec] dintf=[dec] No command dispatch vector was found for the specified interface. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." CWPA-3-PROCCREATEFAIL 3-Error Failed to create [chars] process The Linecard failed to create a process which\n\ which is necessary for proper functioning of the\n\ linecard. cwpa "Copy the error message as it appears and\n\ report it to your technical support \n\ representative. If it is the 'stats export\n\ process' then you might not see input/output\n\ rate and bytes getting incremented in 'show\n\ interface' output for flexwan/flexwan2 non-\n\ channelised interfaces. However you can get\n\ the stats from 'show interface acc' or 'show\n\ interface stats'." CWPA-4-HEADER_TOO_BIG 4-Warning Needs [dec] bytes with only [dec] bytes available. Packet size [dec] received from [chars] buffer [hex] packet start [hex]:\n %-08x:%08x %08x %08x %08x %08x %08x %08x %08x\n %-08x:%08x %08x %08x %08x %08x %08x %08x %08x\n A packet was sent from the PA to either the route processor or the line card. That packet did not have enough available space to append the header. A new particle has been linked to the packet to store the header. - LOG_STD_NO_ACTION CWPAATOM-3-BADLTL 3-Error Bad LTL index 0x[hec] for vlan [dec] local_vc_label [dec] Local Target Logic index value is invalid 7600-mpls "If your EoMPLS traffic is fine then ignore this \n\ If not then contact your Cisco technical support representative." CWRPSPA-3-HWIDB_FAILURE 3-Error Creation: slot [dec] subSlot [dec] port [dec] vc [dec] Failed to create an interface hwidb. cwan LOG_STD_SH_TECH_ACTION CWRPSPA-3-INVALID_PORT_NUM 3-Error slot=[dec] port=[dec] hwidbType=0x[hec] max_port_num=[dec] LCtype=0x[hec] The port number is out of range. cwan LOG_STD_SH_TECH_ACTION CWRPSPA-3-MAX_SPA 3-Error Power to IPSEC-SPA-2G in [chars] is denied because it has exceeded the number allowed[dec] The number of IPSEC-SPA-2G in a chassis is limited. This message is displayed when the number of IPSEC-SPA-2G in the chassis has exceeded this limit. cwan "Use only the number of supported IPSEC-SPA-2G" CWRPSPA-3-NO_HOST_INFO 3-Error slot [dec] subSlot [dec] spaType 0x[hec] Failed to get information about the host linecard. cwan LOG_STD_SH_TECH_ACTION CWRPSPA-3-SPA_NO_HOST_INFO 3-Error slot [dec] subSlot [dec] PID [chars] Failed to get information about the host linecard. cwan LOG_STD_SH_TECH_ACTION CWRPSPA-4-SPA_CMD_NO_RESP 4-Warning [chars]: No response for interface configuration command \[chars]\ A timeout occurred while RP was waiting for a response from line card. This may happen due to line card CPU being too busy to respond to the command. cwan LOG_STD_NO_ACTION CWRPSPA-4-SPA_RESP_CMD_MISMATCH 4-Warning [chars]: Expecting response to interface configuration command \[chars]\ but received response to command \[chars]\. An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded. cwan "Check that the running configuration for the " "interface is correct. If this message occurred on the standby try " "reloading the standby to ensure that its configuration is in sync. " "If this message is repeatable please " LOG_STD_SH_TECH_ACTION CWRPSPA-5-OUT_OF_RESOURCES 5-Notice [chars]: Unable to create [chars] due to SPA resource limitations. The SPA was unable to create the requested resource due to limited hardware or software resources - LOG_STD_NO_ACTION CWRPSPA-6-CARDRELOAD 6-Information Module [dec] reload due to SPA insert in [dec]/[dec]. When inserting a SPA on this carrier card the card is reset. - LOG_STD_NO_ACTION CWS-2-IPC_INIT_FAILED 2-Critical CWS-IPC message handler registration failure rc [dec] Registering an IPC message handler for the CWS feature failed. This will cause the feature to not function. cws-xe LOG_STD_ACTION CWS-3-IPC_INVALID_MSG 3-Error CWS-Invalid request [dec] Received Invalid message from CWS client proxy cws-xe LOG_STD_RECUR_ACTION CWS-3-IPC_NORES 3-Error CWS-No space for the IPC reply size [dec] request [chars] For a request from CWS client proxy it was not possible to allocate space for a reply for the specified size. cws-xe LOG_STD_RECUR_ACTION CWS-3-IPC_OPEN_REPLY 3-Error CWS-IPC Open Reply failed request [chars] For a request from CWS client proxy opening the reply buffer failed cws-xe "This is normally a software issue. " LOG_STD_RECUR_ACTION CWS-3-IPC_SEND_FAILED 3-Error CWS-IPC [chars] [chars] send failed [dec] IPC message send failure cws-xe LOG_STD_ACTION CWS-5-CWS_INVALID_REF_COUNT 5-Notice Invalid ref count [dec] in chunk [hex] CTR has seen an invalid ref count in the NSH pool\n cpp-ucode LOG_STD_NO_ACTION CWS-5-CWS_ON_PATH_DEBUG 5-Notice NSH D-bit set for SIP: [inet] DIP: [inet] Src_node: [dec] Src_If_Id: [dec] Tenant_Id: [dec] CTR has seen an NSH header with D-bit set\n - LOG_STD_NO_ACTION CXSC-2-IPC_FAILURE 2-Critical CXSC-IPC message [chars] handler failed rc [dec] An IPC message handler for the CXSC feature failed. This will cause the feature to not function. qfp-cxsc LOG_STD_ACTION CXSC-2-IPC_INIT_FAILED 2-Critical CXSC-IPC message handler registration failure rc [dec] Registering an IPC message handler for the CXSC feature failed. This will cause the feature to not function. qfp-cxsc LOG_STD_ACTION CXSC-3-CXSC_COND_DEBUG_REG_FAILED 3-Error [chars] Failure occurred when attempting to Register/Initialize conditional debugging. qfp-ucode LOG_STD_ACTION CXSC-3-FEAT_CTX_DOWN 3-Error CXSC-Invalid request [chars] [dec] while context is down While the feature context was not active an invalid request was received from another layer of the CXSC software stack. qfp-cxsc LOG_STD_RECUR_ACTION CXSC-3-FEAT_DOWN 3-Error CXSC-Invalid request [chars] [dec] while feature is down While the feature was not active an invalid request was received from another layer of the CXSC software stack. qfp-cxsc LOG_STD_RECUR_ACTION CXSC-3-IPC_INVALID_MSG 3-Error CXSC-Invalid request [dec] We received an invalid message from another layer of the CXSC software stack. qfp-cxsc LOG_STD_RECUR_ACTION CXSC-3-IPC_INVALID_MSG_LEN 3-Error CXSC-Invalid IPC length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length qfp-cxsc LOG_STD_ACTION CXSC-3-IPC_NORES 3-Error CXSC-No space for the IPC reply size [dec] request [dec] For a request from upper CXSC software stack layers it was not possible to allocate space for a reply for the specified size. qfp-cxsc LOG_STD_RECUR_ACTION CXSC-3-IPC_OPEN_REPLY 3-Error CXSC-IPC Open Reply failed request [dec] For a request from upper CXSC software stack layers it was not possible to open the reply buffer. qfp-cxsc "This is normally a software issue. " LOG_STD_RECUR_ACTION CXSC-3-IPC_SEND_FAILED 3-Error CXSC-IPC [chars] [dec] send failed [dec] IPC message send failure qfp-cxsc LOG_STD_ACTION DAPR_BR-4-FLOW_LIMIT_EXCEEDED 4-Warning curr [dec] max [dec] DAPR Flows exceeded dapr LOG_STD_NO_ACTION DAPR_BR-4-PREFIX_LIMIT_EXCEEDED 4-Warning curr [dec] max [dec] DAPR RIB prefixes exceeded dapr LOG_STD_NO_ACTION DAPR_BR-4-RMAP_LIMIT_EXCEEDED 4-Warning curr [dec] max [dec] DAPR route-map entries exceeded max allowed dapr LOG_STD_NO_ACTION DAPR_BR-5-EGRESS_INTF_NOT_VIABLE 5-Notice [chars] curr-bwkbps %lu min-bwkbps %ld DAPR egress interface not viable dapr LOG_STD_NO_ACTION DAPR_BR-5-EGRESS_INTF_THRESHOLD_EXCEED 5-Notice [chars] curr-util %llu%% max-util %ld%% DAPR egress interface utilization threshold exceeded dapr LOG_STD_NO_ACTION DAPR_BR-5-EGRESS_INTF_UPDOWN 5-Notice [chars] [chars] DAPR egress interface status dapr LOG_STD_NO_ACTION DAPR_BR-5-INGRESS_INTF_UPDOWN 5-Notice [chars] [chars] DAPR ingress interface status dapr LOG_STD_NO_ACTION DAPR_BR-5-NBR_ROUTE_INVALID 5-Notice Neighbor-BR [inet] Invalid route to neighbor Border-Router dapr LOG_STD_NO_ACTION DAPR_BR-5-NBR_TUNNEL_UPDOWN 5-Notice Neighbor-BR [inet] tunnel [chars] Status of tunnel to neighbor Border-Router dapr LOG_STD_ACTION DAPR_BR-5-RESET 5-Notice reason: [chars] Border-Router reset due to mentioned reason dapr LOG_STD_NO_ACTION DAPR_BR-5-RM_ROUTE_INVALID 5-Notice No route or route is via egress Invalid route from Border-Router to Route-Manager dapr LOG_STD_ACTION DAPR_BR-5-STATUS 5-Notice [chars] Border-Router status dapr LOG_STD_NO_ACTION DAPR_RM-3-APP_RT_COMPUTE_FAILED 3-Error [chars] App route compute failed for flow-group dapr LOG_STD_NO_ACTION DAPR_RM-3-BR_REG_FAILED 3-Error BR [chars] reason: [chars] BR Registration failed dapr LOG_STD_ACTION DAPR_RM-3-BR_RESET 3-Error BR [chars] reason: [chars] RM reset the BR due to mentioned reason dapr LOG_STD_ACTION DAPR_RM-3-FLOW_EXP_PKTS_MISSED 3-Error BR [chars] missed-pkts [dec] Flow export packets missed dapr LOG_STD_ACTION DAPR_RM-3-FLOW_INVALID_EGRESS 3-Error flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s last-transition [dec]s ingress-BR [chars] expected-egress [chars]/[dec] reported-egress [chars]/[dec] Flow discovered from unexpected egress dapr LOG_STD_ACTION DAPR_RM-4-APP_REROUTE_FAILED 4-Warning [chars] App route re-compute failed for flow-group dapr LOG_STD_NO_ACTION DAPR_RM-4-FLOW_DATA_RECS_IGNORED 4-Warning BR [chars] reason: [chars] Flow data records ignored dapr LOG_STD_ACTION DAPR_RM-4-FLOW_EXP_PKT_INVALID_SEQ 4-Warning BR [chars] last-seq [dec] curr-seq [dec] Unexpected seq num in flow export pkt dapr LOG_STD_ACTION DAPR_RM-4-FLOW_INVALID_INGRESS 4-Warning flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s last-transition [dec]s ingress-BR [chars] egress-BR/intf [chars]/[dec] ingress-intf [chars] Flow discovered from unexpected ingress dapr LOG_STD_ACTION DAPR_RM-4-FLOW_MULTI_EGRESS 4-Warning flow-group [chars]/[chars]/[dec] state [chars] uptime [dec]s num-egress [dec] prev-egress [chars]/[dec] curr-egress [chars]/[dec] New flow discovered from multiple egresses dapr LOG_STD_ACTION DAPR_RM-4-NO_VIABLE_PATH 4-Warning [chars] No viable path found for flow-group dapr LOG_STD_NO_ACTION DAPR_RM-4-RIB_MISMATCH 4-Warning route-count: old [dec] new [dec] Mismatch of RIB database between BRs and RM dapr LOG_STD_ACTION DAPR_RM-5-BR_STATUS 5-Notice BR [chars] [chars] Border-Router status on RM dapr LOG_STD_NO_ACTION DAPR_RM-5-RM_STATUS 5-Notice [chars] Route-Manager status dapr LOG_STD_NO_ACTION DAPR_RM-6-APP_RT_DEL 6-Information [chars] BW:[dec] App route deleted for flow-group dapr LOG_STD_NO_ACTION DAPR_RM-6-APP_RT_INSTALL 6-Information [chars] BW:[dec] [chars] App route installed for flow-group dapr LOG_STD_NO_ACTION DAPR_RM-6-BR_EVENT 6-Information BR [chars] event: [chars] RM received event from BR dapr LOG_STD_ACTION DAPR_RM-6-RM_RESET 6-Information reason: [chars] RM reset due to the mentioned reason dapr LOG_STD_ACTION DAPR-4-INTERNAL_ERROR 4-Warning [chars] Internal error dapr LOG_STD_ACTION DATA_DESCR-3-CTRLR_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec] - - - DATA_DESCR-3-CTRLR_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec] - - - DATA_DESCR-3-DEFER_FAILURE 3-Error Defer failure on [chars] for descriptor [dec]-[dec]/[dec]/[dec]/[dec] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-DEFER_FAILURE 3-Error Defer failure on [chars] for descriptor [dec]-[dec]/[dec]/[dec]/[dec] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-ENTRY_EXPIRED 3-Error Found expired message entry for descriptor [dec]-[dec]/[dec]/[dec]/[dec] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-ENTRY_EXPIRED 3-Error Found expired message entry for descriptor [dec]-[dec]/[dec]/[dec]/[dec] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-GENERIC_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec] - - - DATA_DESCR-3-GENERIC_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec] - - - DATA_DESCR-3-GENERIC_ENCODE 3-Error Encode failure: [chars] descriptor type=[dec] An internal data descriptor could not be encoded for synchronization for the interface or controller in the run-time module specified in the message output. The failure most likely occurred because of a software error. The descriptor type specified in the message output identifies the type of failure. The system state between the active and standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-GENERIC_ENCODE 3-Error Encode failure: [chars] descriptor type=[dec] An internal data descriptor could not be encoded for synchronization for the interface or controller in the run-time module specified in the message output. The failure most likely occurred because of a software error. The descriptor type specified in the message output identifies the type of failure. The system state between the active and standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-GENERIC_VIRTUAL_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec] - - - DATA_DESCR-3-GENERIC_VIRTUAL_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec] - - - DATA_DESCR-3-HWIDB_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec] - - - DATA_DESCR-3-HWIDB_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec] - - - DATA_DESCR-3-QUEUE_INTERNAL_ERROR 3-Error Internal error on data descriptor queue: [chars] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-QUEUE_INTERNAL_ERROR 3-Error Internal error on data descriptor queue: [chars] Data descriptors are used to encode an interface index in a compact fashion for transfer between redundant route processor units. An error occurred during the processing of a data descriptor. The failure most likely occurred because of a software error. The numeric error code in the message output identifies the failing data descriptor index. The system state between the Active and Standby units might not be properly synchronized. ha-idb-sync LOG_STD_ACTION DATA_DESCR-3-SWIDB_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec] - - - DATA_DESCR-3-SWIDB_DECODE 3-Error Lookup Failure: %0-8x.%0-8x.%0-8x.%0-8x.%0-8x [dec]-[dec]/[dec]/[dec]/[dec]/[dec] - - - DB_INIT_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - DB_INIT_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - DB_LOCK_MGR-3-INITFAIL 3-Error Initialization of the Database Lock Manager facility failed [chars]. An unexpected condition has occurred which resulted in the Database lock manager facililty failing to start. This is a serious problem and means that the Database lock manager facility will not be functional. crimson LOG_STD_ACTION DB_LOCK_MGR-3-OPERFAIL 3-Error Database Lock Manager Operational failure [chars]. An unexpected condition has occurred which resulted in the Database lock manager detecting an operational failure. This means Database lock manager has detected and corrected an unexpected failure condition. crimson LOG_STD_ACTION DB_NTFY_MGR-3-INITFAIL 3-Error Initialization of the Database Notification Manager facility failed [chars]. An unexpected condition has occurred which resulted in the Database notification manager facility failing to start. This is a serious problem and means that the Database notification manager facility will not be functional. crimson LOG_STD_ACTION DB_NTFY_MGR-3-REQPROCFAIL 3-Error Database Notification Manager Request Processing facility failed [chars]. An unexpected condition has occurred which resulted in the Database notification manager facility failing to process a request. This means that some part of Database notification manager facility will not be functional. crimson LOG_STD_ACTION DBCONN-3-BADLICENSEKEY 3-Error Bad license key configured for Database Connection. The license key configured with the dbconn license configuration\n\ command is not valid. dbconn "Check that the license key was entered correctly in the dbconn\n\ license configuration command. Refer to the dbconn feature documentation\n\ for information on how to obtain a valid license key." DBCONN-3-BADMODE 3-Error Unknown mode '[chars]' configured for server [chars] The mode configured for the dbconn server was rejected by the\n\ remote database server. dbconn "Contact your SNA network administrator to determine the correct\n\ name of the mode to use to connect to DB2 on the remote database\n\ server." DBCONN-3-BADRLU 3-Error Bad remote LU '[chars]' configured for server [chars] The remote LU configured for the dbconn server is incorrect. dbconn "Contact your SNA network administrator to determine the correct\n\ name of the remote LU for DB2 on the remote database server. Be sure to\n\ check that the SNA network name is correct as well as the LU name." DBCONN-3-BADTPNAME 3-Error Bad TP name configured for server [chars] The tpname configured for the dbconn server is not recognized by the\n\ remote database server. dbconn "Configure a TP name that is available on the remote database server.\n\ Most DB2 systems will accept the DRDA default TP name of \x076DB\n\ except for SQL/DS. Contact your SNA network administrator and/or\n\ your DB2 administrator to determine the TP name used by your DB2.\n\ To use the DRDA default do not explicitly configure a TP name for your\n\ dbconn server." DBCONN-3-DRDASYNTAX 3-Error DRDA protocol error from server [chars] SYNERRCD x'%02X' An unexpected DRDA protocol error occurred between dbconn and the\n\ remote database server. dbconn LOG_STD_ACTION " If possible also provide the output of the debug dbconn drda\n\ command and an SNA line trace between the router and the remote\n\ database server for the period during which this message appeared." DBCONN-3-LICENSEEXPERROR 3-Error License is expired for Database and Transaction Connection. This system is using a temporary key for its Database and Transaction\n\ Connection. The license is expired. dbconn "Contact StarQuest Software to acquire a permanent key." DBCONN-3-LICENSEEXPWARNING 3-Error License is about to expire for Database and Transaction Connection. This system is using a temporary key for its Database and Transaction\n\ Connection. The license is about to expire. dbconn "Contact StarQuest Software to acquire a permanent key." DBCONN-3-LICENSEHWWARNING 3-Error Number of connections for TXCONN and DBCONN is at 90%% license limit. The number of allowed Database and Transaction Connection client \n\ in this system is reaching the limit. dbconn "Contact StarQuest Software to acquire more license." DBCONN-5-IDLETIMEOUT 5-Notice Client [inet] connected to server [chars] has timed out after %TE. The client was idle for too long and the idle timeout configured\n\ for the dbconn server expired. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-PWDEXPIRED 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The password passed in by the client was rejected by the remote database \n\ server because it's expired. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-PWDINVALID 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The password passed in by the client was rejected by the remote database \n\ server. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-PWDMISSING 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The remote database server requires a userid and password but the \n\ password was not provided. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-SECFAIL 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The userid and/or password passed in by the client were rejected by\n\ the remote database server. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-SECUNKNOWN 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] An unspecified security failure has occurred. The database host system may\n\ be able to provide more specific information. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-UIDINVALID 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The userid used to connect to the remote database server is not valid. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-UIDMISSING 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The remote database server requires a userid but the \n\ userid was not provided. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-UIDREVOKED 5-Notice APPC security failed client [inet] using userid '[chars]' for server [chars] The userid used to connect to the remote database server has been revoked. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-WLMDOWN 5-Notice All WLM routes on server [chars] have become unavailable. Recovery is in progress. A load balanced WLM server has lost connectivity to all destinations in its server list. All client\n\ connections to this server will be rejected until a host in the complex becomes available again. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBCONN-5-WLMMISMATCH 5-Notice WLM transport type mismatch on server [chars]. The transport type within a server list received from a Workload Manager \n\ load balanced database does not match the transport type of the corresponding \n\ dbconn server. If the conflicting server list specifies SNA transport type the \n\ default mode #INTER will be used to establish the connection. dbconn "This is an informational message only. " LOG_STD_NO_ACTION DBMS-2- INITIALIZATION_FAILED 2-Critical DBLIB initialization failed for [chars] Initialization of the database library failed. cmts-platform-infr LOG_STD_RECUR_ACTION DBMS-3- API 3-Error [chars] The specified operation in the api component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- API 3-Error [chars] The specified operation in the api component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- BUNDLE 3-Error [chars] The specified operation in the bundle component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- BUNDLE 3-Error [chars] The specified operation in the bundle component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- CONNECTION 3-Error [chars] The specified operation in the connection component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- CONNECTION 3-Error [chars] The specified operation in the connection component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- DATABASE 3-Error [chars] The specified operation in the database component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- DATABASE 3-Error [chars] The specified operation in the database component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- ENGINE 3-Error [chars] The specified operation in the engine component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- ENGINE 3-Error [chars] The specified operation in the engine component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- IPC_ERROR 3-Error DBLIB ipc failure : [chars] An internal inter-process communication error has occurred. cmts-platform-infr LOG_STD_ACTION DBMS-3- KEY 3-Error [chars] The specified operation in the key component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- KEY 3-Error [chars] The specified operation in the key component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- MALLOC_FAILED 3-Error DBLIB malloc failed for [chars] size [dec] An internal memory allocation has failed. cmts-platform-infr LOG_STD_RECUR_ACTION DBMS-3- MESSAGE 3-Error [chars] The specified operation in the message component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- MESSAGE 3-Error [chars] The specified operation in the message component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- PORT 3-Error [chars] The specified operation in the port component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- PORT 3-Error [chars] The specified operation in the port component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- REPLICATION 3-Error [chars] The specified operation in the replication component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- REPLICATION 3-Error [chars] The specified operation in the replication component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- SHADOW 3-Error [chars] The specified operation in the shadow component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- SHADOW 3-Error [chars] The specified operation in the shadow component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- SNAPSHOT 3-Error [chars] The specified operation in the snapshot component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- SNAPSHOT 3-Error [chars] The specified operation in the snapshot component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- TABLE 3-Error [chars] The specified operation in the table component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- TABLE 3-Error [chars] The specified operation in the table component failed. cmts-platform-infr LOG_STD_NO_ACTION DBMS-3- TDL_ERROR 3-Error DBLIB TDL error : [chars] A TDL messaging error has been detected. cmts-platform-infr LOG_STD_ACTION DBMS-5- CONNECTION_DROP 5-Notice DBLIB connection from [chars] to [chars] dropped An internal socket connection has been dropped. cmts-platform-infr LOG_STD_RECUR_ACTION DBUS-2-UNKNOWN 2-Critical Slot [dec] unknown controller type 0x[hec] ignoring A processor reported a controller type that is unknown to the system.\n\ The processor will not be used and needs to be repaired. - LOG_STD_SH_TECH_ACTION DBUS-3-BADCTRLRTYPE 3-Error Invalid controller type [dec] in slot [dec] An interface processor responded with an unknown or illegal controller\n\ type when queried. This should not happen unless the running software\n\ does not support the interface processor in question or the interface\n\ processor fails. - LOG_STD_ACTION DBUS-3-BADEEPROM 3-Error Invalid EEPROM data found for card in slot [dec] card disabled The ID EEPROM on the indicated card is not programmed correctly. - "Call your Cisco technical support representative for a replacement." DBUS-3-BADHSACONF 3-Error Down rev RSP EPROM found HSA system upgrade EPROM or remove one RSP A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION DBUS-3-CXBUSERR 3-Error Slot [dec] CBus Error - - "Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION DBUS-3-DAUGHTER_STATS 3-Error Slot [dec] control 0x[hec] status 0x[hec] A processor reported an error. This message is sent out in conjunction\n\ with other error messages to provide additional information. - LOG_STD_SH_TECH_ACTION DBUS-3-DBUSDISABLED 3-Error Slot [dec] disabled will be restarted. A processor was disabled due to an error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested. - "Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION DBUS-3-DBUSINTERR 3-Error Slot [dec] Internal Error A processor reported an internal error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested. - "Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION DBUS-3-DBUSINTERRSWSET 3-Error Slot [dec] Internal Error due to VIP crash A processor reported an error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested. - "Reinstall the processor or download the microcode. " LOG_STD_RECUR_ACTION DBUS-3-MSGOVERFLOW 3-Error Slot [dec] too many DBUS messages A board in the slot identified in the error message tried to send\n\ too many logger messages. - LOG_STD_SH_TECH_ACTION DBUS-3-MSGPABADCONFIG 3-Error Slot [dec] has an unsucessfully configured PA in bay [dec] The PA in the slot is not sucessfully configured either because the VIP is\n\ incompatible with it or because the IOS has no pertinent drivers. - "Please refer to the documentation of the PA to get a list of compatible\n\ VIP's. If the VIP that contains the PA is listed as supported please refer to\n\ the CCO page for IOS versions that support the PA. Otherwise seat the PA in one\n\ of the supported VIP's and verify that the IOS version supports the PA." DBUS-3-MSGPAUNSUP 3-Error Slot [dec] has an unsupported PA in bay [dec] The PA in the slot is not supported either because the VIP is\n\ incompatible with it or because the IOS has no pertinent drivers. - "Please refer to the documentation of the PA to get a list of compatible\n\ VIP's. If the VIP that contains the PA is listed as supported please refer to\n\ the CCO page for IOS versions that support the PA. Otherwise seat the PA in one\n\ of the supported VIP's and verify that the IOS version supports the PA." DBUS-3-NOMAGIC 3-Error No magic number found in RP1 EEPROM The structure containing the system MAC address needed by the OIR\n\ facility cannot be found in the RP EEPROM. The RP must be returned for\n\ reprogramming. - "Return the RP for reprogramming and call your Cisco technical\n\ support representative for assistance." DBUS-3-NORESP 3-Error bad or no response slot [dec] A board in the slot identified in the error message failed to\n\ respond. - LOG_STD_SH_TECH_ACTION DBUS-3-NOSUPPORT 3-Error No driver support in this image for [chars] in slot [dec] card type [dec] - disabled The Cisco IOS image does not have driver support code\n\ for the specified interface processor. - "Remove the unsupported interface processor card or\n\ reload the router with a Cisco IOS image that has driver\n\ support code for that interface processor card." DBUS-3-ORFS_NOTINITIALIZED 3-Error ORFS is not initialized When oir-remove-failing-slot is invoked the software attempts to initialize parameters. This initialization failed and the service will not be available. rsp "If this message is seen please try entering the service " "oir-remove-failing-slot command again. This message should " "not cause any functional failures. If the message does cause " "an IOS performance issue please check Bug Toolkit on the web " "for existing bugs and if none are found " LOG_STD_SH_TECH_ACTION DBUS-3-SLOTCOMP 3-Error Slot [dec] dbus error slot 0x[hec] and complement 0x[hec] do not match A processor reported a mismatch between the contents of the slot\n\ register and its complement. This condition indicates a hardware\n\ failure in the diagnostic bus controller on that processor or on the\n\ diagnostic bus. The processor will be reset and not used until the next\n\ OIR event or microcode download when it will be retested. - LOG_STD_SH_TECH_ACTION DBUS-3-SW_NOTRDY 3-Error DBUS software not ready for slot [dec] after [chars] elapsed [dec] status 0x[hec] An interface processor failed to come online after being reset. A software or hardware error occurred. rsp c5rsm "Please refer to Bug Toolkit on the Cisco web-site to check for " "existing bugs. If you do not find one obtain the output of show " "tech and show log and open a TAC case." DBUS-3-WCSCTRLRERR 3-Error Slot [dec] WCS Controller Instruction Error - - LOG_STD_SH_TECH_ACTION DBUS-3-WCSERR 3-Error Slot [dec] WCS controller in error state 0x[hec] resetting - - "Reset the processor and load new microcode. " LOG_STD_RECUR_ACTION DBUS-3-WCSFLOW 3-Error Slot [dec] flow cntrl error loading WCS last data 0x[hec] pos [dec] A processor indicated an error condition while downloading microcode.\n\ The status cmd/data and pos numbers shown in the message reflect the\n\ error condition the last byte of microcode loaded and the position in\n\ the file respectively. If this error appears the microcode download\n\ is aborted and the ROM microcode is loaded. - LOG_STD_RECUR_ACTION DBUS-3-WCSLDERR 3-Error Slot [dec] error loading WCS status 0x[hec] cmd/data 0x[hec] pos [dec] A processor indicated an error condition while downloading microcode.\n\ The status cmd/data and pos numbers shown in the message reflect the\n\ error condition the last byte of microcode loaded and the position in\n\ the file respectively. If this error appears the microcode download\n\ is aborted and the ROM microcode is loaded. - LOG_STD_RECUR_ACTION DBUS-3-WCSPARERR 3-Error Slot [dec] WCS Controller Parity Error A processor reported a WCS parity error. The processor will be reset\n\ and not used until the next OIR event or microcode download when it\n\ will be retested. - "Replace the processor or download microcode. If this message recurs\n\ call your Cisco technical support representative for assistance." DBUS-3-XILINX 3-Error ready wait timeout slot [dec] The field-programmable gate arrays on an interface processor failed to\n\ load after being reset. This indicates a probable software or hardware\n\ problem. - LOG_STD_ACTION DC-3-BUILTIN_INIT_FAIL 3-Error [chars] Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-BUILTIN_INIT_FAIL 3-Error [chars] Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-BUILTIN_INIT_FAIL 3-Error [chars] Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-BUILTIN_INIT_FAIL 3-Error [chars] Initilization of Device classifier Built-in database failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-CHECK_INIT_FAIL 3-Error [chars] Loading of the Checks databae in Device classifier failed. dc LOG_STD_ACTION DC-3-CHECK_INIT_FAIL 3-Error [chars] Loading of the Checks databae in Device classifier failed. dc LOG_STD_ACTION DC-3-CHECK_INIT_FAIL 3-Error [chars] Loading of the Checks databae in Device classifier failed. dc LOG_STD_ACTION DC-3-CHECK_INIT_FAIL 3-Error [chars] Loading of the Checks databae in Device classifier failed. dc LOG_STD_ACTION DC-3-DB_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Initilization of Device classifier Internal database failed So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-DB_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Initilization of Device classifier Internal database failed So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-DB_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Initilization of Device classifier Internal database failed So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-DB_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Initilization of Device classifier Internal database failed So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-DC_ADD_USR_CHK 3-Error Addition of custom checks failed : [chars]. Internal error returned during addition of custom checks. dc - DC-3-DC_ADD_USR_PROFILE 3-Error Addition of custom profiles failed : [chars]. Internal error returned during addition of custom profiles. dc - DC-3-DC_ADD_USR_RULE 3-Error Addition of custom rules failed : [chars]. Internal error returned during addition of custom rules. dc - DC-3-DC_DISABLED 3-Error [chars]. The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles dc "The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier" DC-3-DC_DISABLED 3-Error [chars]. The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles dc "The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier" DC-3-DC_DISABLED 3-Error [chars]. The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles dc "The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier" DC-3-DC_DISABLED 3-Error [chars]. The device classifier is disabled due to an error condition encountered during initialization or parsing the profiles dc "The specified error message is logged." "After the error condition is resolved" "re-enable the device classifier" DC-3-DISABLE_FAIL 3-Error Failed to disable DC. Internal error occured trying to disable Device Classifier. dc "Please run the command: show macro auto monitor clients and try disabling" "the clients" DC-3-DISABLE_FAIL 3-Error Failed to disable DC. Internal error occured trying to disable Device Classifier. dc "Please run the command: show macro auto monitor clients and try disabling" "the clients" DC-3-DISABLE_FAIL 3-Error Failed to disable DC. Internal error occured trying to disable Device Classifier. dc "Please run the command: show macro auto monitor clients and try disabling" "the clients" DC-3-DISABLE_FAIL 3-Error Failed to disable DC. Internal error occured trying to disable Device Classifier. dc "Please run the command: show macro auto monitor clients and try disabling" "the clients" DC-3-ENABLE_FAIL 3-Error Failed to enable DC. Internal error occured trying to enable Device Classifier. dc "Please check the previous DC error messages and take the relevant action" DC-3-ENABLE_FAIL 3-Error Failed to enable DC. Internal error occured trying to enable Device Classifier. dc "Please check the previous DC error messages and take the relevant action" DC-3-ENABLE_FAIL 3-Error Failed to enable DC. Internal error occured trying to enable Device Classifier. dc "Please check the previous DC error messages and take the relevant action" DC-3-ENABLE_FAIL 3-Error Failed to enable DC. Internal error occured trying to enable Device Classifier. dc "Please check the previous DC error messages and take the relevant action" DC-3-FILE_CHECKSUM 3-Error Checksum [chars] failed for the profile file: [chars] Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_CHECKSUM 3-Error Checksum [chars] failed for the profile file: [chars] Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_CHECKSUM 3-Error Checksum [chars] failed for the profile file: [chars] Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_CHECKSUM 3-Error Checksum [chars] failed for the profile file: [chars] Checksum computation or verification failed for the profiles file. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_READ_ERROR 3-Error Error [chars] the profile file: [chars] There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_READ_ERROR 3-Error Error [chars] the profile file: [chars] There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_READ_ERROR 3-Error Error [chars] the profile file: [chars] There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-FILE_READ_ERROR 3-Error Error [chars] the profile file: [chars] There was an error reading the profile file contents. The profiles in the errored file cannot be loaded into the device classifier. dc - DC-3-HRPC_SYNC 3-Error Error on member switch [dec] error_code = [dec] Internal error occured while trying to sync Device Classifier.state dc "Please check the state of the stack members" DC-3-HRPC_SYNC 3-Error Error on member switch [dec] error_code = [dec] Internal error occured while trying to sync Device Classifier.state dc "Please check the state of the stack members" DC-3-HRPC_SYNC 3-Error Error on member switch [dec] error_code = [dec] Internal error occured while trying to sync Device Classifier.state dc "Please check the state of the stack members" DC-3-HRPC_SYNC 3-Error Error on member switch [dec] error_code = [dec] Internal error occured while trying to sync Device Classifier.state dc "Please check the state of the stack members" DC-3-INCOMPATIBLE_PROFILE_VERSION 3-Error Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec] An incompatible profile version is detected. The device classifier feature will be operationally down. dc "Reload the expected version of device profiles file to the " "system and re-enable the device classifier " DC-3-INCOMPATIBLE_PROFILE_VERSION 3-Error Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec] An incompatible profile version is detected. The device classifier feature will be operationally down. dc "Reload the expected version of device profiles file to the " "system and re-enable the device classifier " DC-3-INCOMPATIBLE_PROFILE_VERSION 3-Error Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec] An incompatible profile version is detected. The device classifier feature will be operationally down. dc "Reload the expected version of device profiles file to the " "system and re-enable the device classifier " DC-3-INCOMPATIBLE_PROFILE_VERSION 3-Error Incompatible version of Profile detected in [chars]. Expected version:[dec] Version found:[dec] An incompatible profile version is detected. The device classifier feature will be operationally down. dc "Reload the expected version of device profiles file to the " "system and re-enable the device classifier " DC-3-MAX_OUI_EXCEEDED 3-Error [chars]. The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_OUI_EXCEEDED 3-Error [chars]. The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_OUI_EXCEEDED 3-Error [chars]. The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_OUI_EXCEEDED 3-Error [chars]. The maximum number of OUI codes that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_PROFILES_EXCEEDED 3-Error [chars]. The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_PROFILES_EXCEEDED 3-Error [chars]. The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_PROFILES_EXCEEDED 3-Error total profiles [dec] exceeds the max supported [dec] The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_PROFILES_EXCEEDED 3-Error [chars]. The maximum number of profiles that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_RULES_EXCEEDED 3-Error [chars]. The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_RULES_EXCEEDED 3-Error [chars]. The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_RULES_EXCEEDED 3-Error [chars]. The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-MAX_RULES_EXCEEDED 3-Error [chars]. The maximum number of rules that can be defined in device profiles exceeded the maximum limit. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reduce the number of rules in the device profiles file and" "reload it into the " "system and re-enable the device classifier" DC-3-NO_MEM 3-Error [chars]. There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Increase the memory size in the system and " "re-enable the device classifier" DC-3-NO_MEM 3-Error [chars]. There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Increase the memory size in the system and " "re-enable the device classifier" DC-3-NO_MEM 3-Error [chars]. There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Increase the memory size in the system and " "re-enable the device classifier" DC-3-NO_MEM 3-Error [chars]. There is no memory left to allocate in the system The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Increase the memory size in the system and " "re-enable the device classifier" DC-3-OUI_INIT_FAIL 3-Error OUI Table initialization failed for [chars] Loading of the OUI databae in Device classifier failed. dc LOG_STD_ACTION DC-3-OUI_INIT_FAIL 3-Error OUI Table initialization failed for [chars] Loading of the OUI databae in Device classifier failed. dc LOG_STD_ACTION DC-3-OUI_INIT_FAIL 3-Error OUI Table initialization failed for [chars] Loading of the OUI databae in Device classifier failed. dc LOG_STD_ACTION DC-3-OUI_INIT_FAIL 3-Error OUI Table initialization failed for [chars] Loading of the OUI databae in Device classifier failed. dc LOG_STD_ACTION DC-3-PATTERN_NOT_FOUND 3-Error [chars] The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reload the Device Profiles file to the flash and re-enable the device classifier" DC-3-PATTERN_NOT_FOUND 3-Error [chars] The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reload the Device Profiles file to the flash and re-enable the device classifier" DC-3-PATTERN_NOT_FOUND 3-Error [chars] The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reload the Device Pr/scratch/stevenl/polaris/wab_amur_eedge_polaris/novaofiles file to the flash and re-enable the device classifier" DC-3-PATTERN_NOT_FOUND 3-Error [chars] The device profiles file parsing failed. This indicates that the file may be corrupt. The device classifier will be operationally down if failure occured for the Embedded profiles. dc "Reload the Device Pr/scratch/stevenl/polaris/wab_amur_eedge_polaris/novaofiles file to the flash and re-enable the device classifier" DC-3-SM_API 3-Error [chars] return [chars]. Internal error returned by Session Manager api. dc - DC-3-SM_API 3-Error [chars] return [chars]. Internal error returned by Session Manager api. dc - DC-3-SM_API 3-Error [chars] return [chars]. Internal error returned by Session Manager api. dc - DC-3-SM_API 3-Error [chars] return [chars]. Internal error returned by Session Manager api. dc - DC-3-SM_GET 3-Error Failed to get [chars]. Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results. dc - DC-3-SM_GET 3-Error Failed to get [chars]. Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results. dc - DC-3-SM_GET 3-Error Failed to get [chars]. Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results. dc - DC-3-SM_GET 3-Error Failed to get [chars]. Internal error occured during communication with Session Manager. This may cause the show command not to display the device classification results. dc - DC-3-SM_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Registraton of Device classifier with SM failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-SM_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Registraton of Device classifier with SM failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-SM_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Registraton of Device classifier with SM failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-SM_INIT_FAIL 3-Error Device Classifier disabled. [chars] initialization failed Registraton of Device classifier with SM failed. So the device classifier will be operationally down. dc LOG_STD_ACTION DC-3-SM_UPDATE 3-Error Failed to update [chars]. Internal error occured during device classification . This may cause the device to be unknown. dc - DC-3-SM_UPDATE 3-Error Failed to update [chars]. Internal error occured during device classification . This may cause the device to be unknown. dc - DC-3-SM_UPDATE 3-Error Failed to update [chars]. Internal error occured during device classification . This may cause the device to be unknown. dc - DC-3-SM_UPDATE 3-Error Failed to update [chars]. Internal error occured during device classification . This may cause the device to be unknown. dc - DC-4-FILE_OPEN_WARNING 4-Warning Not able to open [chars] The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles. dc " Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. " DC-4-FILE_OPEN_WARNING 4-Warning Not able to open [chars] The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles. dc " Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. " DC-4-FILE_OPEN_WARNING 4-Warning Not able to open [chars] The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles. dc " Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. " DC-4-FILE_OPEN_WARNING 4-Warning Not able to open [chars] The device classifier did not find the default profile file or it may be corrupted. DC is working using built-in profiles. dc " Perform archive download using the tar bundle image to install " " the profile file in the flash. " " Reload the switch with the image to see the warning message is gone. " DC-6-DEFAULT_INIT_INFO 6-Information [chars] The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles. dc LOG_STD_ACTION DC-6-DEFAULT_INIT_INFO 6-Information [chars] The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles. dc LOG_STD_ACTION DC-6-DEFAULT_INIT_INFO 6-Information [chars] The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles. dc LOG_STD_ACTION DC-6-DEFAULT_INIT_INFO 6-Information [chars] The default profiles are not loaded and those devices will not be classified. Device classifier will continue to work with built-in profiles. dc LOG_STD_ACTION DCA_INFRA-2-DCA_PROXY_IPC_INIT_FAILED 2-Critical DCA IPC initialization failure result: [dec]. Cisco internal software error. DCA initialization detected that the Proxy IPC interface initialization failed. esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-2-DCA_PROXY_IPC_SEND_FAIL 2-Critical DCA IPC response send failure result: [dec]. Cisco internal software error. DCA detected an error when sending a IPC response. esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_ASYN_CB_ERROR_RSP 3-Error DCA received an asyn callback with an error response trans_id: [dec] Result: [dec] DCA received an asyn callback with an error response esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_ASYN_CB_SEQ_MISMATCH 3-Error DCA received an asyn callback with an unexpected sequence number trans_id: [dec] DCA received an asyn callback with an unexpected sequence number esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_ASYN_CB_STATE_MISMATCH 3-Error DCA received an asyn callback while in an unexpected state trans_id: [dec] DCA received an asyn callback while in an unexpected state esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_INV_PROXY_MSG 3-Error DCA Proxy received invalid Message ID [dec] Cisco internal software error. DCA Proxy received an invalid Message ID. This message will be ignored. esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_PROXY_IPC_ALLOC_FAIL 3-Error DCA Proxy [chars] response lost due to buffer allocation failure Cisco internal software error. DCA Proxy message processing detected a IPC buffer allocation failure during response processing. The associated DCA functionality may not be fully functional as a result of this condition. esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_REQUEST_WHILE_BUSY 3-Error DCA received a new request while previous request in progress DCA received a new request while previous request in progress esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_STATE_TRANS_ERROR 3-Error DCA encountered an error during state transition processing trans_id: [dec] DCA encountered an error during state transition processing esg-dp-infra "File a bug with the platform DCA infra team" DCA_INFRA-3-DCA_STATE_TRANS_FAIL 3-Error DCA encountered an state transition error trans_id: [dec] Result: [dec] DCA encountered an state transition error esg-dp-infra "File a bug with the platform DCA infra team" DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEAD-4-SCARLET 4-Warning * Interface [chars]: I knew without asking she was into the blues - - - DEAD-4-SCARLET 4-Warning - - - - DEADADJ-3-LCON 3-Error ERRMSG_NOFLAGS - - - DEADADJ-3-LCON 3-Error ERRMSG_NOFLAGS - - - DEC21140-1-INITFAIL 1-Alert msgtxt_initfail The Fast Ethernet port initialization failed. This can be\n\ caused by disconnected cabling or a failure to detect the\n\ media in use. - "Check the cabling. Try initializing the port again. " LOG_STD_SH_TECH_ACTION DEC21140-3-RXFIFO 3-Error Unit [dec] receive FIFO overflow The Fast Ethernet receiver was unable to hand received data to a\n\ hardware buffer because the input rate exceeded the receiver's\n\ ability to handle the data. This could be caused by excessive\n\ system load. - LOG_STD_RECUR_ACTION DEC21140-3-UNDERFLO 3-Error Unit [dec] Tx FIFO underflow The Fast Ethernet transmitter was ready to transmit before a packet\n\ was in the buffer. This could be caused by excessive system load. - LOG_STD_RECUR_ACTION DEC21140-5-COLL 5-Notice Unit [dec] excessive collisions A Fast Ethernet packet has been dropped because too many\n\ attempts to transmit it were stopped by collisions. This can\n\ be caused by a Fast Ethernet segment which is full to capacity\n\ or by other equipment on the LAN malfunctioning. - LOG_STD_NO_ACTION DEC21140-5-JABBER 5-Notice Unit [dec] jabber timeout The transmitter for the port adapter's Fast Ethernet port has\n\ timed out and caused the transmission of a packet to fail. - LOG_STD_RECUR_ACTION DEC21140-5-LATECOLL 5-Notice Unit [dec] late collision error Late collisions happen when a collision occurs after transmitting \n\ the preamble. The packet will be retransmitted but this could \n\ indicate that another device is failing to detect when the network \n\ is in use. - "If this recurs check for malfunctions in other devices on the \n\ Fast Ethernet." DEC21140-5-LOSTCARR 5-Notice Unit [dec] lost carrier The Fast Ethernet port lost carrier while transmitting\n\ meaning that it is no longer receiving signals from the LAN.\n\ This can be caused by disconnected Fast Ethernet cabling or\n\ a transceiver failure. - "If the message recurs check your Fast Ethernet cabling and port\n\ adapter first. If the problem cannot be located follow these\n\ directions. " LOG_STD_RECUR_ACTION DEC21140-5-NOCARR 5-Notice Unit [dec] no carrier The Fast Ethernet port did not find a carrier when preparing to\n\ transmit a packet meaning that it is no longer receiving signals\n\ from the LAN. This can be caused by disconnected Fast Ethernet\n\ cabling or a transceiver failure. - "Check your Fast Ethernet cabling and port adapter. " LOG_STD_RECUR_ACTION DEC21140-5-WATCHDOG 5-Notice Unit [dec] enormous packet received A packet received via Fast Ethernet was dropped due to excessive \n\ size. - "Adjust the MTU of the interface if necessary. Otherwise\n\ no action is required." DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG 3-Error [chars] The system is unable to reset the configuration firmware LOG_STD_ACTION DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG 3-Error [chars] The system is unable to reset the configuration firmware LOG_STD_ACTION DECLASSIFICATION-3-UNABLE_TO_RESET_CONFIG 3-Error [chars] The system is unable to reset the configuration firmware LOG_STD_ACTION DECLASSIFICATION-5-CONFIG_IS_RESET 5-Notice [chars] The configuration is reset and the system will now reboot firmware LOG_STD_ACTION DECLASSIFICATION-5-CONFIG_IS_RESET 5-Notice [chars] The configuration is reset and the system will now reboot firmware LOG_STD_ACTION DECLASSIFICATION-5-CONFIG_IS_RESET 5-Notice [chars] The configuration is reset and the system will now reboot firmware LOG_STD_ACTION DECONFIG_SHUTDOWN-6-LDP 6-Information ERRMSG_NOFLAGS - - - DECONFIG_SHUTDOWN-6-LDP 6-Information ERRMSG_NOFLAGS - - - DEFCASE_BINDING_PIE-3-LCON 3-Error ERRMSG_NOFLAGS - - - DEFCASE_BINDING_PIE-3-LCON 3-Error ERRMSG_NOFLAGS - - - DEREG_FAIL-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - DEREG_FAIL-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - DFP-4-AGENT_NOT_FOUND 4-Warning [chars] Service has not been registered with DFP. No such service registered with DFP subystem. dfp LOG_STD_RECUR_ACTION DFP-4-BAD_LISTEN 4-Warning Service [chars] - Listen failed Listen for DFP Manager failed. dfp LOG_STD_RECUR_ACTION DFP-4-BAD_POINTER 4-Warning [chars] Application did not set pointer Application passed invalid pointer to DFP subsystem dfp LOG_STD_RECUR_ACTION DFP-4-BAD_SEND 4-Warning Manager [inet]:[dec] - Send failed Sending a message to DFP Manager failed dfp LOG_STD_RECUR_ACTION DFP-4-BIND_FAIL 4-Warning Failure binding port [dec] to socket for service [chars]. Problem with call to socket bind. dfp LOG_STD_RECUR_ACTION DFP-4-ENQUEUE 4-Warning Process enqueue failed: [chars] An unexpected error occurred while enqueueing a DFP element dfp LOG_STD_RECUR_ACTION DFP-4-NO_PARSE 4-Warning Manager [inet]: Service [chars] - Could not parse message Could not parse message from DFP Manager dfp LOG_STD_RECUR_ACTION DFP-4-NO_PROCESS_START 4-Warning Could not start process for service [chars] Could not start DFP Process for service [chars] dfp LOG_STD_RECUR_ACTION DFP-4-NO_QUEUE_REQUEST 4-Warning Could not queue request for [chars] for service [chars] Could not queue request to the DFP process for specific action dfp LOG_STD_RECUR_ACTION DFP-4-NUM_TOO_LARGE 4-Warning [chars] Application sent too many values Application sent too many values to DFP subsystem dfp LOG_STD_RECUR_ACTION DFP-4-PACKET_TOO_SMALL 4-Warning The DFP packet is too small from manager [inet] service [chars]. A DFP packet has been received that is too small. dfp LOG_STD_RECUR_ACTION DFP-4-READ_ERR 4-Warning Manager [inet]: Service [chars] - Too many read errors Too many errors reading message header from DFP Manager dfp LOG_STD_RECUR_ACTION DFP-4-REPEAT_SERVICE_INIT 4-Warning Service [chars] is already intialized cannot re-initialize The application has atempted to re-initialize a service dfp LOG_STD_RECUR_ACTION DFP-4-SECURITY_FAIL 4-Warning [chars] security information in CASA packet from manager [inet] service [chars]. Security check failed. casa "Make sure all CASA/DFP systems are configured with the same password." DFP-4-SOCK_ERR 4-Warning Manager [inet]: Service [chars] - Socket_recv error [dec] Socket_recv error receiving message from DFP Manager dfp LOG_STD_RECUR_ACTION DFP-4-STRING_TOO_LONG 4-Warning The string [chars] exceeds 15 characters - too long for service name. The user input a service string that exceeds 15 characters dfp LOG_STD_RECUR_ACTION DFP-4-SUBSYS_NOT_UP 4-Warning Service [chars] - attempted to register before DFP Subsytem is up. Problem with order of subsystem initialization. dfp LOG_STD_RECUR_ACTION DFP-4-UKN_CON 4-Warning Manager [inet] Service [chars] - Unknown connection state [dec] Unknown connection state processing DFP timer dfp LOG_STD_RECUR_ACTION DFP-4-UNK_TYPE 4-Warning Manager [inet]: Service [chars] - Unknown message type [dec] Message from DFP Manager has unknown type dfp LOG_STD_RECUR_ACTION DHCP_SNOOPING_CAT3550-3-MVR_INSTALL 3-Error Cannot install [chars] ACLs for DHCP Snooping probably no TCAM space When DHCP Snooping is enabled ACLs need to be installed into the TCAM. This will fail if there is insufficient space in the TCAM. firmware "Reduce the number of input and/or output" "PACLs and/or VACLs to make space in the TCAM." DHCP_SNOOPING_CAT3550-3-UNEXPECTED_EVENT 3-Error Process received unknown event major [hec] minor [hec]. - - - DHCP_SNOOPING_ISSU-2-GET_BUFFER 2-Critical DHCP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars] The DHCP Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. dhcp-snooping "show logging and show checkpoint client" DHCP_SNOOPING_ISSU-2-INIT 2-Critical DHCP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars] The DHCP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. dhcp-snooping LOG_STD_ACTION DHCP_SNOOPING_ISSU-2-SEND_NEGO_FAILED 2-Critical DHCP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars] The DHCP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. dhcp-snooping "show logging and show checkpoint client" DHCP_SNOOPING_ISSU-2-SESSION_NEGO 2-Critical DHCP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The DHCP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. dhcp-snooping "show issu session and " "show issu negotiated capability " DHCP_SNOOPING_ISSU-2-SESSION_REGISTRY 2-Critical DHCP Snooping ISSU client failed to register session information. Error: [dec] [chars] The DHCP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. dhcp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " DHCP_SNOOPING_ISSU-3-INVALID_SESSION 3-Error DHCP Snooping ISSU client does not have a valid registered session. The DHCP Snooping ISSU client does not have a valid registered session. dhcp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " DHCP_SNOOPING_ISSU-3-MSG_NOT_OK 3-Error DHCP Snooping ISSU client 'Message Type [dec]' is not compatible The DHCP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed. dhcp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " DHCP_SNOOPING_ISSU-3-MSG_SIZE 3-Error DHCP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The DHCP Snooping ISSU client failed to calculate the MTU for the specified message. The DHCP Snooping ISSU client is not able to send the message to the standby device. dhcp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " DHCP_SNOOPING_ISSU-3-SESSION_UNREGISTRY 3-Error DHCP Snooping ISSU client failed to unregister session information. Error: [dec] [chars] The DHCP Snooping ISSU client failed to unregister session information. dhcp-snooping "show issu session and " "show issu negotiated capability " DHCP_SNOOPING_ISSU-3-TRANSFORM_FAIL 3-Error DHCP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The DHCP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the DHCP Snooping state between the active device and the standby device is not identical. dhcp-snooping "show issu session and " "show issu negotiated version " DHCP_SNOOPING-3-DHCP_SNOOPING_INTERNAL_ERROR 3-Error DHCP Snooping internal error [chars] A software sanity check failed in the DHCP Snooping process. dhcp-snooping LOG_STD_SH_TECH_ACTION DHCP_SNOOPING-4-AGENT_OPERATION_FAILED 4-Warning DHCP snooping binding transfer failed. [chars] This message provides the reason of failure when a database transfer\n\ has failed. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-AGENT_OPERATION_FAILED_N 4-Warning DHCP snooping binding transfer failed[dec]. [chars] This message provides the reason of failure when a database transfer\n\ has failed. This log message is rate limited. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-BVM_MAC_AUTH_FAIL 4-Warning Drop packet on the interface [chars] \n\ Bridge mode VM authentication is pending for the VM This message indicates that a DHCP Discover packet was dropped\n\ due to bridge mode vm mac not being authenticated. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-DHCP_SNOOPING_DATABASE_FLASH_WARNING 4-Warning Saving DHCP snooping bindings to [chars] can fill up your device causing the writes of bindings to device to fail. Saving DHCP Snooping bindings to a flash file system such as\n\ bootflash or slot0 could cause the flash to fill up. Possible\n\ consequences include the long delay to regain console write\n\ failures for database config regular squeeze requirements and\n\ reduced life of flash due to regular squeeze operations etc. dhcp-snooping "Alternate destination locations for database agent " "include tftp ftp rcp etc. Please see the help " "at command line for a complete list of options." DHCP_SNOOPING-4-DHCP_SNOOPING_ERRDISABLE_WARNING 4-Warning DHCP Snooping received [dec] DHCP packets on interface [chars] DHCP Snooping detected a DHCP packet rate limit violation on a particular interface. The interface will be error disabled. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-DHCP_SNOOPING_PVLAN_WARNING 4-Warning DHCP Snooping configuration may not take effect on secondary vlan [dec]. [chars] If private vlan feature is enabled DHCP Snooping configuration on primary vlan will automatically propagate to all secondary vlans. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-DHCP_SNOOPING_RATE_LIMIT_EXCEEDED 4-Warning The interface [chars] is receiving more than the threshold set This message indicates that a DHCP packets are coming into cpu\n\ at a much higher rate than the specified threshold. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-INVALID_RELEASE_OR_DECLINE_PKT 4-Warning The interface [chars] has received a DHCP Release/Decline packet \n\ with no existing binding entry for it This message indicates that a DHCP Release/Decline packet was received \n\ with no corresponding binding entry. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-IP_SOURCE_BINDING_NON_EXISTING_VLAN_WARNING 4-Warning IP source binding is configured on non existing vlan [dec]. IP source binding is configured on a non existing vlan. dhcp-snooping "Please make sure that the L2 VLAN is configured before configuring a " "DHCP Snooping Binding. If you see this message even though L2 VLAN is " "configured in the system please contact Cisco Technical Assistance " "Center." DHCP_SNOOPING-4-IP_SOURCE_BINDING_PVLAN_WARNING 4-Warning IP source filter may not take effect on secondary vlan [dec] where IP source binding is configured. [chars] If private vlan feature is enabled IP source filter on primary vlan will automatically propagate to all secondary vlans. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-OPTION82_INSERTION_FAIL 4-Warning The interface [chars] is not able to insert opt82 into the packet\n\ because of insufficient space in the packet This message indicates that a DHCP packet was not inserted with\n\ opt82 data due to insufficient space in the packet. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-QUEUE_FULL 4-Warning Fail to enqueue DHCP packet into processing queue: [chars] the queue is most likely full and packet will be dropped. If the DHCP snooping bindings are loaded by the DHCP snooping database agent and NTP is not sync then the calculated lease duration for the bindings will be incorrect. firmware "Synchronize NTP on the switch to provide an accurate " "time and date for the system clock. Then disable and " "re-enable DHCP snooping to clear the bindings database." DHCP_SNOOPING-4-SSO_SYNC_ACK_ERROR 4-Warning Error is encountered in processing acknowledgement for DHCP snooping binding sync [chars]. ack message txn id: 0x[hec] This message indicates that there is an error in handling of the\n\ dhcp snooping binding sync acknowledgement. In most of these cases\n\ the ack message is ignored. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-4-STANDBY_AGENT_OPERATION_FAILED 4-Warning DHCP snooping binding transfer failed on the Standby Supervisor. [chars] This message provides the reason of failure when a database transfer\n\ has failed on the Standby Supervisor. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-5-DHCP_SNOOPING_FAKE_INTERFACE 5-Notice [chars] drop message with mismatched source interface the binding is not updated message type: [chars] MAC sa: [enet] DHCP Snooping discovers some host is trying to act as another host\n\ on the network and trying to carry out a DOS attack on that host. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-5-DHCP_SNOOPING_MATCH_MAC_FAIL 5-Notice [chars] drop message because the chaddr doesn't match source mac message type: [chars] chaddr: [enet] MAC sa: [enet] DHCP Snooping enables match-source-mac validation and the check is\n\ failed. There maybe a malicious host trying to carry out a DOS\n\ attack on the DHCP server. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-5-DHCP_SNOOPING_NONZERO_GIADDR 5-Notice [chars] drop message with non-zero giaddr or option82 value on untrusted port message type: [chars] MAC sa: [enet] DHCP Snooping discovers DHCP packet with certain option value not\n\ allowed on the untrusted port some host maybe trying to act as a DHCP\n\ relay or server. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-5-DHCP_SNOOPING_UNTRUSTED_PORT 5-Notice [chars] drop message on untrusted port message type: [chars] MAC sa: [enet] DHCP Snooping discovers certain types of DHCP message not allowed on\n\ the untrusted interface some host maybe trying to act as a DHCP server. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-AGENT_OPERATION_SUCCEEDED 6-Information DHCP snooping database [chars] succeeded. This message indicates that the given binding transfer has succeeded.\n\ This message is logged only once after some failure to indicate that the\n\ switch has recovered from failures. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-BINDING_COLLISION 6-Information Binding collision. [dec] bindings ignored This message indicates that the given number of bindings from the \n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the system has a binding for the given mac address\n\ and vlan combination by the time the switch read the ignored binding\n\ from the file. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-INTERFACE_NOT_VALID 6-Information Interface not valid. [dec] bindings ignored. This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the interface indicated by the ignored binding\n\ either does not exist in the system or it's a router or dhcp \n\ snooping trusted port. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-LEASE_EXPIRED 6-Information Lease Expired. [dec] bindings ignored. This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because their lease has expired. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-PARSE_FAILURE 6-Information Parsing failed for [dec] bindings. This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because of parsing failures. dhcp-snooping LOG_STD_NO_ACTION DHCP_SNOOPING-6-VLAN_NOT_SUPPORTED 6-Information Vlan not supported. [dec] bindings ignored. This message indicates that the given number of bindings from the\n\ database file have been ignored when the file is read. The bindings\n\ are ignored because the vlan indicated by the ignored binding\n\ no longer exists in the system. dhcp-snooping LOG_STD_NO_ACTION DHCP-3-HA_INIT_FAIL 3-Error Function [chars] in DHCP client failed to initialize: [chars]\n A high availability related function in the DHCP client failed to initialize properly. If you are using a platform with a redundant processor or box-to-box redundancy DHCP client settings may fail to be preserved if the main processor fails forcing use of the standby. dhcp "Please contact the TAC for assistance." DHCP-5-RESTART 5-Notice Interface [chars] is being restarted by DHCP\n DHCP is restarting the interface. dhcp LOG_STD_NO_ACTION DHCP-6-ADDRESS_ASSIGN 6-Information Interface [chars] assigned DHCP address [inet] mask [inet] hostname [chars]\n The interface has been allocated an address via DHCP - "This is an informational message. No action is required" DHCPD-2-MALLOC_ERROR 2-Critical There is inadequate memory for DHCP services. DHCP could not allocate mandatory data structures. - "Add more memory." DHCPD-2-NO_PROCESS 2-Critical DHCP could not start its [chars] process. DHCP could not start one of its processes. - "Add more memory." DHCPD-2-READ_DEADLOCK 2-Critical DHCP has detected a deadlock condition excessive read failures. The DHCP server could not read bindings from any database agent. All\n\ read attempts have failed. To prevent a possible deadlock the server\n\ has made all pool addresses available for assignment. - "Verify that all URLs are correct and connectivity exists between the \n\ server and all database agents. Check for corrupt database files. All\n\ files must contain the *time* and *end* keywords. Execute the command \n\ \"show ip dhcp database.\" If there are aborted file transfers increase \n\ the appropriate timeouts. Restart the DHCP server." DHCPD-2-RECVMSG_ERROR 2-Critical Recvmsg failed unexpectedly. DHCP services have been terminated. Reason for failure is unknown. dhcp-server "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DHCPD-2-SOCKET_ERROR 2-Critical DHCP could not open UDP port [dec]. DHCP could not open UDP port 67 bootps. - "Check if another application is using UDP port 67. If the port is\n\ available add more memory." DHCPD-3-HA_INIT_FAIL 3-Error Function [chars] in DHCP server failed to initialize: [chars]\n A high availability related function in the DHCP server failed to initialize properly. If you are using a platform with a redundant processor or box-to-box redundancy DHCP server data may fail to be preserved if the main processor fails forcing use of the standby. dhcp "Please contact the TAC for assistance." DHCPD-3-NO_AAA_CONTEXT 3-Error AAA configured but no AAA context in [chars]\n DHCP is attempting to use AAA to grant a DHCP lease but no AAA context is associated with the binding dhcp "Please contact the TAC for assistance." DHCPD-3-READ_ERROR 3-Error DHCP could not read bindings from [chars]. The DHCP server could not read bindings from the specified database \n\ agent. - "Verify that the URL is correct and connectivity exists between the \n\ server and database agent. Check for a corrupt database file. The\n\ file must contain the *time* and *end* keywords. Execute the command \n\ \"show ip dhcp database.\" If there are aborted file transfers increase \n\ the database transfer timeout." DHCPD-3-WRITE_ERROR 3-Error DHCP could not write bindings to [chars]. The DHCP server could not write bindings to the specified database \n\ agent. - "Verify that the URL is correct and connectivity exists between the \n\ server and database agent. Execute the command \"show ip dhcp database.\"\n\ If there are aborted file transfers increase the database transfer \n\ timeout." DHCPD-4-DECLINE_CONFLICT 4-Warning DHCP address conflict: client [chars] declined %I. The DHCP client has detected an address conflict. Another host is using\n\ the specified IP address. After resolving the conflict execute the\n\ command \clear ip dhcp conflict.\ - "Resolve the misconfiguration. Clear the conflict from the DHCP \n\ database." DHCPD-4-HA_CONFIG_MISMATCH 4-Warning DHCP pool [chars] configuration on Active is not matched on the Standby. Reason for failure is unknown. dhcp "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DHCPD-4-PING_CONFLICT 4-Warning DHCP address conflict: server pinged %I. The DHCP server has detected an address conflict. Another host is using\n\ the specified IP address. After resolving the conflict execute the\n\ command \clear ip dhcp conflict.\ - "Resolve the misconfiguration. Clear the conflict from the DHCP \n\ database." DHCPD-4-RELAY_ONLY 4-Warning DHCP will run as a relay agent only. DHCP could not start its database process. The server component has \n\ been disabled. Only the relay agent is active. - "Add more memory." DHCPD-6-HIGH_UTIL 6-Information Pool \[chars]\ is in high utilization state [dec] addresses used out of [dec]. Threshold set at [dec]%%. The pool's utilization has exceeded the user configured high watermark. dhcp "Examine the DHCP pool and determine if the pool needs more IP addresses" " than currently allocated." DHCPD-6-LOW_UTIL 6-Information Pool \[chars]\ is in low utilization state [dec] addresses used out of [dec]. Threshold set at [dec]%%. The pool's utilization has fallen below the user configured high watermark. dhcp "Examine the DHCP pool and determine if the pool needs more IP addresses" " than currently allocated." DHCPD-6-MALFORMED_OPTION 6-Information Invalid option [dec] message type [dec] received from client [chars]\n DHCP client sent malformed option. dhcp "Check if DHCP client can be configured to send valid option." DHCPV6C-3-NOPACKET 3-Error Cannot setup or duplicate a socket packet Most likely a resource problem within the system. dhcp LOG_STD_REDUCE_ACTION DHCPV6C-3-NOSOCKET 3-Error Cannot create DHCPv6 client socket Most likely no IP enabled on any interface or a resource problem within the system. dhcp LOG_STD_REDUCE_ACTION DHCPV6C-4-ZEROXID 4-Warning Calculated DHCPv6 Lease Query xid is zero. Nothing is wrong just drop the LQv6 msg After multiple tries the generated LQv6 msg xid is zero by accident. Just drop the LQv6 msg. dhcp LOG_STD_REDUCE_ACTION DHCPV6R-3-INVALID_USR_LINKADDR 3-Error Invalid user specified link-address %P idb [chars] in ipv6 dhcp relay CLI.\n Removing user specified invalid address from the CLI. Invalid link-address has been provisioned in the ipv6 relay destination CLI. dhcp LOG_STD_REDUCE_ACTION DHCPV6R-3-INVALID_USR_SRCADDR 3-Error Invalid user specified source-address %P idb [chars] in ipv6 dhcp relay CLI.\n Removing user specified invalid address from the CLI and auto-computing source with SAS. Invalid source-address has been provisioned in the ipv6 relay destination CLI. dhcp LOG_STD_REDUCE_ACTION DHCPV6S-3-DBNOTLOADED 3-Error Binding database not loaded Fail to load the DHCPv6 binding database. dhcp LOG_STD_ACTION DHCPV6S-3-DBOPEN 3-Error Openning [chars]: [chars] Fail to open a DHCPv6 binding database file. dhcp LOG_STD_ACTION DHCPV6S-3-DBREAD 3-Error Reading file: [chars] Fail to read a DHCPv6 binding database file. dhcp LOG_STD_ACTION DHCPV6S-3-DBWRITE 3-Error Writing file: [chars] Fail to write a DHCPv6 binding database file. dhcp LOG_STD_ACTION DHCPV6S-3-NOPACKET 3-Error Cannot setup or duplicate a DHCPv6 server socket packet Most likely a resource problem within the system. dhcp LOG_STD_REDUCE_ACTION DIAG-3-ALWAYS_ENABLE_TEST 3-Error [chars]: The users are not allow to disable monitoring for Test #[dec] The specified health monitoring test must be run and cannot be disabled. gold "Nothing. The specific health monitoring test cannot be disabled by " "design. The system is working properly." DIAG-3-ALWAYS_ENABLE_TEST 3-Error [chars]: The users are not allow to disable monitoring for Test #[dec] The specified health monitoring test must be run and cannot be disabled. gold "Nothing. The specific health monitoring test cannot be disabled by " "design. The system is working properly." DIAG-3-CARD_ABSENT 3-Error [chars] is not detected A line card could not be located in a slot where a diagnostic action was requested. gold "Ensure the targeted line card is properly seated in the specified slot. " "If the line card is properly seated ensure the correct slot was " "indicated in the command-line interface. If the line card is well-seated " "and the correct slot was specified copy the error message exactly as it " "appears on the screen as well as the output of show tech-support and " "paste the output into a separate file. Contact your technical support " "representative with the gathered information." DIAG-3-CARD_ABSENT 3-Error [chars] is not detected A line card could not be located in a slot where a diagnostic action was requested. gold "Ensure the targeted line card is properly seated in the specified slot. " "If the line card is properly seated ensure the correct slot was " "indicated in the command-line interface. If the line card is well-seated " "and the correct slot was specified copy the error message exactly as it " "appears on the screen as well as the output of show tech-support and " "paste the output into a separate file. Contact your technical support " "representative with the gathered information." DIAG-3-CREATE_PROCESS_FAIL 3-Error Create process [chars] failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-CREATE_PROCESS_FAIL 3-Error Create process [chars] failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-DIAG_RUNNING 3-Error [chars]: Diagnostic is currently running A diagnostic test is currently being run on the specified card and additional tests cannot be run until the previously requested tests have been completed. gold "The system is working properly and no user action is required. If you " "want to run the specified diagnostic test either wait for the current " "diagnostic test to finish and then run the test or stop the current " "test and run the new test." DIAG-3-DIAG_RUNNING 3-Error [chars]: Diagnostic is currently running A diagnostic test is currently being run on the specified card and additional tests cannot be run until the previously requested tests have been completed. gold "The system is working properly and no user action is required. If you " "want to run the specified diagnostic test either wait for the current " "diagnostic test to finish and then run the test or stop the current " "test and run the new test." DIAG-3-ENQUEUE_FAIL 3-Error [chars]: process_enqueue failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-ENQUEUE_FAIL 3-Error [chars]: process_enqueue failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-FIXED_INTERVAL_TEST 3-Error [chars]: The users are not allow to change monitoring interval of Test #[dec] The specified health monitoring test interval is not user-configurable and therefore cannot be changed. gold "Nothing. The specific health monitoring interval is not user-" "configurable by design so nothing can be done to change the interval." DIAG-3-FIXED_INTERVAL_TEST 3-Error [chars]: The users are not allow to change monitoring interval of Test #[dec] The specified health monitoring test interval is not user-configurable and therefore cannot be changed. gold "Nothing. The specific health monitoring interval is not user-" "configurable by design so nothing can be done to change the interval." DIAG-3-GET_ARGU_FAIL 3-Error Get argument failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-GET_ARGU_FAIL 3-Error Get argument failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-INVALID_DEVICE 3-Error Invalid device number : [chars] A diagnostic request is being made on a device that does not exist gold "Ensure that the specified device number 1-based exists and is valid" DIAG-3-INVALID_DEVICE 3-Error Invalid device number : [chars] A diagnostic request is being made on a device that does not exist gold "Ensure that the specified device number 1-based exists and is valid" DIAG-3-INVALID_MONITORING_INTERVAL 3-Error [chars]: The [chars][ID=[dec]] monitoring interval must be at least %lld millisec The specified test monitoring interval is too small. gold "The system is working properly and no user action is required. If you " "want to specify a smaller testing interval the error message text " "provides the lowest possible configurable interval for the specified " "monitoring interval." DIAG-3-INVALID_MONITORING_INTERVAL 3-Error [chars]: The [chars][ID=[dec]] monitoring interval must be at least %lld millisec The specified test monitoring interval is too small. gold "The system is working properly and no user action is required. If you " "want to specify a smaller testing interval the error message text " "provides the lowest possible configurable interval for the specified " "monitoring interval." DIAG-3-INVALID_PORT 3-Error Invalid port number : [chars] A diagnostic request is being made on a port that does not exist. gold "Ensure the specified port number exists and that the correct port number " "is being specified." DIAG-3-INVALID_PORT 3-Error Invalid port number : [chars] A diagnostic request is being made on a port that does not exist. gold "Ensure the specified port number exists and that the correct port number " "is being specified." DIAG-3-INVALID_TEST 3-Error Invalid test: [chars] A test that does not exist was requested. gold "Ensure the specified test is supported by the line card. The " "list of available tests and their associated test IDs can be retrieved " "using show diagnostic content." DIAG-3-INVALID_TEST 3-Error Invalid test: [chars] A test that does not exist was requested. gold "Ensure the specified test is supported by the line card. The " "list of available tests and their associated test IDs can be retrieved " "using show diagnostic content." DIAG-3-MAJOR 3-Error [chars]: [chars] detected a Major Error. Please use 'show diagnostic result ' to see test results. A major error was detected during diagnostic testing. gold "Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information." DIAG-3-MAJOR 3-Error [chars]: [chars] detected a Major Error. Please use 'show diagnostic result ' to see test results. A major error was detected during diagnostic testing. gold "Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information." DIAG-3-MINOR 3-Error [chars]: [chars] detected a Minor Error. Please use 'show diagnostic result ' to see test results. A minor error was detected during diagnostic testing. gold "Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information." DIAG-3-MINOR 3-Error [chars]: [chars] detected a Minor Error. Please use 'show diagnostic result ' to see test results. A minor error was detected during diagnostic testing. gold "Re-seat the card and retry the test. If the same result occurs after " "reseating the card and retrying the test copy the error message " "exactly as it appears on the screen and gather the output of show " "tech-support and any other relevant information. Contact your " "technical support representative with the gathered information." DIAG-3-MONITOR_DISABLE 3-Error [chars]: Monitoring test:[dec] is disabled since default interval is zero The specified test is no longer a health monitoring test because health monitoring has been disabled. gold "The system is working properly and no user action is required. If you " "want the requested test to be a health monitoring test enable health " "monitoring and ensure your test is enabled as a health monitoring test." DIAG-3-MONITOR_DISABLE 3-Error [chars]: Monitoring test:[dec] is disabled since default interval is zero The specified test is no longer a health monitoring test because health monitoring has been disabled. gold "The system is working properly and no user action is required. If you " "want the requested test to be a health monitoring test enable health " "monitoring and ensure your test is enabled as a health monitoring test." DIAG-3-MONITOR_INTERVAL_ZERO 3-Error [chars]: Monitoring interval is 0. Cannot enable monitoring for Test #[dec] Health Monitoring cannot be enabled for the specified test because the interval for the test has been set to 0. gold "If you are comfortable not running the specified health monitoring test " "nothing. If you would like to enable the specified test for health " "monitoring reset the interval to a number other than 0." DIAG-3-MONITOR_INTERVAL_ZERO 3-Error [chars]: Monitoring interval is 0. Cannot enable monitoring for Test #[dec] Health Monitoring cannot be enabled for the specified test because the interval for the test has been set to 0. gold "If you are comfortable not running the specified health monitoring test " "nothing. If you would like to enable the specified test for health " "monitoring reset the interval to a number other than 0." DIAG-3-NO_DIAG_RUNNING 3-Error [chars]: Diagnostic is not running An attempt to stop a diagnostic test that was not running was made. gold "None. This is an informational message." DIAG-3-NO_DIAG_RUNNING 3-Error [chars]: Diagnostic is not running An attempt to stop a diagnostic test that was not running was made. gold "None. This is an informational message." DIAG-3-NOT_MONITORING_TEST 3-Error [chars]: The test:[dec] cannot be used as health monitoring test The specified test number cannot be used as a health monitoring test. gold "Nothing. The system is working properly and the specified test cannot " "be configured as a health monitoring test." DIAG-3-NOT_MONITORING_TEST 3-Error [chars]: The test:[dec] cannot be used as health monitoring test The specified test number cannot be used as a health monitoring test. gold "Nothing. The system is working properly and the specified test cannot " "be configured as a health monitoring test." DIAG-3-SET_ARGU_FAIL 3-Error Set argument failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-SET_ARGU_FAIL 3-Error Set argument failed An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-TEST_FAIL 3-Error [chars]: [chars]{ID=[dec]} has failed. Error code = 0x[hec] [chars] A diagnostic test has found an error on the line card. gold "Ensure the line card is firmly in the slot reseat if necessary and " "attempt to run the test again if the line card is not seated properly " "in the slot. If the line card was properly seated in the slot copy the " "error message exactly as it appears on the console gather the output " "of show tech-support and contact your Cisco technical support " "representative with the gathered information." DIAG-3-TEST_FAIL 3-Error [chars]: [chars]{ID=[dec]} has failed. Error code = 0x[hec] [chars] A diagnostic test has found an error on the line card. gold "Ensure the line card is firmly in the slot reseat if necessary and " "attempt to run the test again if the line card is not seated properly " "in the slot. If the line card was properly seated in the slot copy the " "error message exactly as it appears on the console gather the output " "of show tech-support and contact your Cisco technical support " "representative with the gathered information." DIAG-3-TEST_NOT_SUPPORT 3-Error [chars]: [chars]{ID=[dec]} is not supported The diagnostic test is not supported on current chassis configuration. gold "Nothing. The test cannot be run but this message does not indicate a " "problem with the system." DIAG-3-TEST_NOT_SUPPORT 3-Error [chars]: [chars]{ID=[dec]} is not supported The diagnostic test is not supported on current chassis configuration. gold "Nothing. The test cannot be run but this message does not indicate a " "problem with the system." DIAG-3-TEST_SKIPPED 3-Error [chars]: [chars]{ID=[dec]} is skipped The specified diagnostic test cannot be run. gold "Nothing. Although the test cannot be run this message does not indicate " "a problem." DIAG-3-TEST_SKIPPED 3-Error [chars]: [chars]{ID=[dec]} is skipped The specified diagnostic test cannot be run. gold "Nothing. Although the test cannot be run this message does not indicate " "a problem." DIAG-3-UNKNOWN_OPCODE 3-Error [chars]: Unknown opcode %ld is received An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-3-UNKNOWN_OPCODE 3-Error [chars]: Unknown opcode %ld is received An internal software error occurred. gold "Copy the error message exactly as it appears on the screen and gather " "the output of show tech-support and any other relevant information. " "Contact your technical support representative with the gathered " "information." DIAG-4-CONFIG_REAPPLY 4-Warning Please reapply config command '[chars]' after the card is online. The specified config command cannot be applied. gold "The system is working properly and the specified command cannot" "be applied. Please reapply the config command after the module" "is online." DIAG-4-CONFIG_REAPPLY 4-Warning Please reapply config command '[chars]' after the card is online. The specified config command cannot be applied. gold "The system is working properly and the specified command cannot" "be applied. Please reapply the config command after the module" "is online." DIAG-6-BYPASS 6-Information [chars]: Diagnostics is bypassed This is an informational message stating that diagnostics testing was not performed on the card because diagnostic testing was disabled in the user configuration. gold "This behavior is consistent with the user configuration and no action " "needs to be taken. If you want to run bootup diagnostics enable bootup" " diagnostics by using the diagnostic bootup command." DIAG-6-BYPASS 6-Information [chars]: Diagnostics is bypassed This is an informational message stating that diagnostics testing was not performed on the card because diagnostic testing was disabled in the user configuration. gold "This behavior is consistent with the user configuration and no action " "needs to be taken. If you want to run bootup diagnostics enable bootup" " diagnostics by using the diagnostic bootup command." DIAG-6-DIAG_OK 6-Information [chars]: Passed [chars] The diagnostic tests did not detect any error on the card. gold "Nothing. This is an informational message stating that the line card " "passed the diagnostic tests." DIAG-6-DIAG_OK 6-Information [chars]: Passed [chars] The diagnostic tests did not detect any error on the card. gold "Nothing. This is an informational message stating that the line card " "passed the diagnostic tests." DIAG-6-DIAG_STOPPED 6-Information [chars]: Diagnostic is stopped. Diagnostic test has stopped. gold "Nothing. This is an informational message stating that diagnostic " "testing has been stopped. If you want the test to run to completion " "rerun the test." DIAG-6-DIAG_STOPPED 6-Information [chars]: Diagnostic is stopped. Diagnostic test has stopped. gold "Nothing. This is an informational message stating that diagnostic " "testing has been stopped. If you want the test to run to completion " "rerun the test." DIAG-6-NO_TEST 6-Information [chars]: No test to run The diagnostic test cannot find tests to run. gold "In some cases on some platforms a Field Diagnostic image needs to be " "loaded onto the line card if you want to run the test. If applicable " "download a Field Diagnostic image onto the line card. In other cases " "the test is simply not available. This message is an informational and " "does not require user action." DIAG-6-NO_TEST 6-Information [chars]: No test to run The diagnostic test cannot find tests to run. gold "In some cases on some platforms a Field Diagnostic image needs to be " "loaded onto the line card if you want to run the test. If applicable " "download a Field Diagnostic image onto the line card. In other cases " "the test is simply not available. This message is an informational and " "does not require user action." DIAG-6-RUN_COMPLETE 6-Information [chars]: Running Complete Diagnostics... Complete Diagnostic is running on the card gold "Nothing. This is an informational message and the system is working " "properly." DIAG-6-RUN_COMPLETE 6-Information [chars]: Running Complete Diagnostics... Complete Diagnostic is running on the card gold "Nothing. This is an informational message and the system is working " "properly." DIAG-6-RUN_MINIMUM 6-Information [chars]: Running Minimal Diagnostics... Minimum Diagnostic is running on the card gold "Nothing. This is an informational message and the system is working " "properly." DIAG-6-RUN_MINIMUM 6-Information [chars]: Running Minimal Diagnostics... Minimum Diagnostic is running on the card gold "Nothing. This is an informational message and the system is working " "properly." DIAG-6-SCHED_COMPLETE 6-Information [chars]: Scheduled Online Diagnostic is completed The scheduled Diagnostic test is complete. gold "Check the results and proceed accordingly. This is an information " "message only to indicate that Diagnostic testing is complete. The router " "is working properly and no action is needed based on this message." DIAG-6-SCHED_COMPLETE 6-Information [chars]: Scheduled Online Diagnostic is completed The scheduled Diagnostic test is complete. gold "Check the results and proceed accordingly. This is an information " "message only to indicate that Diagnostic testing is complete. The router " "is working properly and no action is needed based on this message." DIAG-6-SCHED_RUNNING 6-Information [chars]: Performing Scheduled Online Diagnostic... The scheduled diagnostic test is running. gold "Nothing. The diagnostic test is being run as configured and the system " "is working properly." DIAG-6-SCHED_RUNNING 6-Information [chars]: Performing Scheduled Online Diagnostic... The scheduled diagnostic test is running. gold "Nothing. The diagnostic test is being run as configured and the system " "is working properly." DIAG-6-SCHED_STOPPED 6-Information [chars]: Scheduled Online Diagnostic is stopped The scheduled Diagnostic test has been stopped. gold "If you do not want the test to run nothing. If you want the test to " "run schedule the test or run the test manually." DIAG-6-SCHED_STOPPED 6-Information [chars]: Scheduled Online Diagnostic is stopped The scheduled Diagnostic test has been stopped. gold "If you do not want the test to run nothing. If you want the test to " "run schedule the test or run the test manually." DIAG-6-SCHEDULE_IS_REMOVED 6-Information [chars]: Schedule Diagnostic for [[chars] [chars] %2ld:%02ld.] is removed The scheduled online diagnostic tests are no longer configured. This message usually appears after a scheduled test is removed by the user or a card is removed from the chassis. gold "If you want the scheduling tests to be removed nothing. If you want " "the scheduled tests to still be run reconfigure the scheduled tests." DIAG-6-SCHEDULE_IS_REMOVED 6-Information [chars]: Schedule Diagnostic for [[chars] [chars] %2ld:%02ld.] is removed The scheduled online diagnostic tests are no longer configured. This message usually appears after a scheduled test is removed by the user or a card is removed from the chassis. gold "If you want the scheduling tests to be removed nothing. If you want " "the scheduled tests to still be run reconfigure the scheduled tests." DIAG-6-SIMULATED_TEST_RESULT 6-Information [chars]: [chars] test result is simulated. The specified test's result is simulated. The failure does not indicate software nor hardware fault gold "Nothing. The test failure is simulated as specified by the user." DIAG-6-SIMULATED_TEST_RESULT 6-Information [chars]: [chars] test result is simulated. The specified test's result is simulated. The failure does not indicate software nor hardware fault gold "Nothing. The test failure is simulated as specified by the user." DIAG-6-SKIP_ONDEMAND_ACTIVE_TO_STANDBY_TEST 6-Information [chars]: [chars] cannot be executed for active device. The specified test can only be run from the active supervisor to test standby supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIAG-6-SKIP_ONDEMAND_ACTIVE_TO_STANDBY_TEST 6-Information [chars]: [chars] cannot be executed for active device. The specified test can only be run from the active supervisor to test standby supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIAG-6-SKIP_ONDEMAND_STANDBY_CARD_TEST 6-Information [chars]: [chars] cannot be executed. The specified test can only be run on a standby supervisor from the standby supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIAG-6-SKIP_ONDEMAND_STANDBY_CARD_TEST 6-Information [chars]: [chars] cannot be executed. The specified test can only be run on a standby supervisor from the standby supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIAG-6-TEST_OK 6-Information [chars]: [chars]{ID=[dec]} has completed successfully Diagnostic testing was completed and no errors were found on the line card. gold "This is an informational message indicating that Field Diagnostic " "testing has completed successfully. The system is working properly and " "no action is required based on this error message." DIAG-6-TEST_OK 6-Information [chars]: [chars]{ID=[dec]} has completed successfully Diagnostic testing was completed and no errors were found on the line card. gold "This is an informational message indicating that Field Diagnostic " "testing has completed successfully. The system is working properly and " "no action is required based on this error message." DIAG-6-TEST_RUNNING 6-Information [chars]: Running [chars]{ID=[dec]} ... Diagnostic testing is running a test on the card gold "Nothing. This is an informational message and the system should be " "working properly." DIAG-6-TEST_RUNNING 6-Information [chars]: Running [chars]{ID=[dec]} ... Diagnostic testing is running a test on the card gold "Nothing. This is an informational message and the system should be " "working properly." DIAG-6-TEST_SKIPPED_FROM_ACTIVE 6-Information [chars]: [chars] cannot be executed from active supervisor. The specified test cannot be run from active supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIAG-6-TEST_SKIPPED_FROM_ACTIVE 6-Information [chars]: [chars] cannot be executed from active supervisor. The specified test cannot be run from active supervisor. gold "Nothing. The test cannot be run but the system is working properly." DIALER_LIST_PROXY-3-PROXY_ALLOC_PAK_FAILED 3-Error alloc pak failed alloc pak failed. cpp-ucode LOG_STD_ACTION DIALER_LIST_PROXY-3-PROXY_IPC_FAILED 3-Error [chars] failed to send ipc rc: [dec] send ipc failed. cpp-ucode LOG_STD_ACTION DIALER_LIST_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION DIALER_LIST_PROXY-3-PROXY_MEM_EXTEND_FAILED 3-Error IPC subtype: [dec] add more memory failed. cpp-ucode LOG_STD_ACTION DIALER_LIST_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION DIALER_LIST_PROXY-4-PROXY_IPC_INVALID_MSG_LEN 4-Warning [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length. cpp-ucode LOG_STD_ACTION DIALER_LIST-3-CHUNK_CREATE_FAIL 3-Error DIALER LIST - fialed to create chunk pool Chunk create failed. Dialer List will not be able to finish initialization. cpp-ucode LOG_STD_ACTION DIALER_LIST-3-CHUNK_DESTROY_FAIL 3-Error DIALER LIST - fialed to destroy chunk pool Chunk destroy failed. cpp-ucode LOG_STD_ACTION DIALER-2-CIRCUITCOUNT 2-Critical Dialer count 0 on [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION DIALER-2-NOSWIDB 2-Critical No software interface associated with hw interface [chars] An internal software error occurred. - "Call your technical support representative and report the error\n\ message the system version and the router configuration. Use the\n\ show version command to obtain the software version." DIALER-2-NULLPTR 2-Critical Unexpected null pointer in [chars] An internal software error occurred. - LOG_STD_SH_TECH_ACTION DIALER-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. - LOG_STD_ACTION DIALER-4-MTU_WARNING 4-Warning Current MTU setting of [dec] on [chars] is being overwritten by setting of [dec] defined by [chars]. This is a warning message indicating that an interface setting is changed based on a dialer rotary group memebership. - LOG_STD_NO_ACTION DIALER-6-BIND 6-Information Interface [chars] bound to profile [chars] This is a status message indicating that a dialer interface has\n\ been bound to a dialer profile. - LOG_STD_NO_ACTION DIALER-6-UNBIND 6-Information Interface [chars] unbound from profile [chars] This is a status message indicating that a dialer interface has\n\ been unbound to a dialer profile. - LOG_STD_NO_ACTION DIALPEER_DB-3-ADDPEER_MEM_THRESHOLD 3-Error Addition of dial-peers limited by available memory\n The available memory does not permit the addition of more dial-peers. ios-voice "Increase the processor memory in order to be able to add more\n\ dialpeers." DIALPEER_DB-3-ADDPEER_MEM_THRESHOLD 3-Error Addition of dial-peers limited by available memory\n The available memory does not permit the addition of more dial-peers. ios-voice "Increase the processor memory in order to be able to add more\n\ dialpeers." DIALPEER_DB-3-ADDPEER_PLATFORM_LIMIT 3-Error Addition of dial-peers limited by platform\n This platform does not permit the addition of more dial-peers. ios-voice "Reduce the number of dial-peers in your numbering plan." DIALPEER_DB-3-ADDPEER_PLATFORM_LIMIT 3-Error Addition of dial-peers limited by platform\n This platform does not permit the addition of more dial-peers. ios-voice "Reduce the number of dial-peers in your numbering plan." DIALPEER_DB-3-DIALPEER_ACCOUNTING 3-Error Connections for dial-peer [dec] is negative. Resetting connections to 0.\n Active Connections for dial-peer is negative. ios-voice "Verify if dial-peers were removed with active calls associated to them\n\ and added back while the calls were still connected." DIALPEER_DB-3-DIALPEER_ACCOUNTING 3-Error Connections for dial-peer [dec] is negative. Resetting connections to 0.\n Active Connections for dial-peer is negative. ios-voice "Verify if dial-peers were removed with active calls associated to them\n\ and added back while the calls were still connected." DIALPEER_DB-3-DP_MALLOC_FAIL 3-Error Could not allocate memory in [chars] for tag [dec]\n Ran out of memory voice-dialpeer "Observe why memory is exhausted" DIALPEER_DB-3-DP_MALLOC_FAIL 3-Error Could not allocate memory in [chars] for tag [dec]\n Ran out of memory voice-dialpeer "Observe why memory is exhausted" DIALPEER_DB-3-NODEPMAP 3-Error Could not load e164-pattern-map [dec]\n url=[chars]\n errno=[dec]=[chars] Could not read in the e164-pattern-map voice-dialpeer "Check that map exists on the server and is readable." DIALPEER_DB-3-NODEPMAP 3-Error Could not load e164-pattern-map [dec]\n url=[chars]\n errno=[dec]=[chars] Could not read in the e164-pattern-map voice-dialpeer "Check that map exists on the server and is readable." DIALPEER_DB-3-NOE164TRANSURL 3-Error Could not load e164-translation [dec]\n url=[chars]\n error=[chars][dec] Could not get the voice class e164-translation url data file voice-dialpeer "Check that url data file exists on the server and is readable." DIALPEER_DB-3-NOE164TRANSURL 3-Error Could not load e164-translation [dec]\n url=[chars]\n error=[chars][dec] Could not get the voice class e164-translation url data file voice-dialpeer "Check that url data file exists on the server and is readable." DIALPEER_DB-3-NOMAP 3-Error Could not load dnis-map [chars]\n url=[chars]\n errno=[dec]=[chars] Could not read in the dnis-map ios-voice "Check that map exists on the server and is readable." DIALPEER_DB-3-NOMAP 3-Error Could not load dnis-map [chars]\n url=[chars]\n errno=[dec]=[chars] Could not read in the dnis-map ios-voice "Check that map exists on the server and is readable." DIALPEER_DB-6-ADDPEER_WARNING 6-Information Addition of too many dial-peers may affect performance\n The number of dial-peers is high. This will have an effect on the\n\ dial-peer lookup time resulting in longer call setup time. ios-voice "Use the minimum number of dial-peers necessary for your numbering plan." DIALPEER_DB-6-ADDPEER_WARNING 6-Information Addition of too many dial-peers may affect performance\n The number of dial-peers is high. This will have an effect on the\n\ dial-peer lookup time resulting in longer call setup time. ios-voice "Use the minimum number of dial-peers necessary for your numbering plan." DIALPEER_DB-6-FB_ENTRY_NOT_CREATED 6-Information Could not create probe for tag [dec]\n Fallback cache full voice-dialpeer "Increase Fallaback cache size" DIALPEER_DB-6-FB_ENTRY_NOT_CREATED 6-Information Could not create probe for tag [dec]\n Fallback cache full voice-dialpeer "Increase Fallaback cache size" DIALSHELF-2-DSCDOWN 2-Critical DSC in slot [dec] changes state to down. DSC in dial shelf went down. - - DIALSHELF-2-TIMEOUT 2-Critical [chars] slot [dec] after [dec] secs in state '[chars]' The specified dial shelf slot timed out as per the message.\n\ Either a software or a hardware component has failed. - "Try removing and reinserting the card. If that does not help\n\ try a different card. If problem persists contact your\n\ technical support representative." DIALSHELF-2-UNDEFCARD 2-Critical Card type [dec] in slot [dec] The software does not have a driver for the card in specified\n\ slot. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIALSHELF-3-EVENT 3-Error Unknown event [dec] for slot [dec] The software generated an unknown event for the specified\n\ slot. This is a software error. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIALSHELF-3-INVALIDMSG 3-Error [chars] [dec] The router shelf received an invalid message from the DSC in\n\ the dial shelf. This is a software error or compatibility issue.\n\ Check the software versions on the router shelf and the DSC. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIALSHELF-3-MSG 3-Error Unknown message type [dec] from DSC The router shelf received an unknown message from the DSC in\n\ the dial shelf. This is a software error or compatibility issue.\n\ Check the software versions on the router shelf and the DSC. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIALSHELF-3-SLOTSTATUS 3-Error Invalid change from [chars] [dec] to [chars] [dec] for slot [dec] The software detected an invalid state change for the specified\n\ slot. This is a software error. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIALSHELF-4-UNRECOMMENDED 4-Warning Number of [chars] may exceed recommended configuration On NPE200 more than one CT3 or more than two T1/E1 are installed\n\ this exceeds the recommended configuration. - "Stay within recommended limit of CT3/T1/E1 or install split \n\ dial-shelf configuration or upgrade router-shelf to NPE300." DIALSHELF-6-RELOAD 6-Information Reload requested for card in shelf [dec] slot [dec]. The command \'hw-module slot / reload\' was entered.\n\ This is a confirmation that the command is being processed. - "None" DIGISIGN-2-MISMATCH_KEYS 2-Critical %%CRITICAL: System identified a mismatch between the show version output and the key type used in signing. [chars] is a signed [chars] software\n System identified a mismatch in software type. This might be a modified software. digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-2-MISMATCH_KEYS 2-Critical %%CRITICAL: System identified a mismatch between the show version output and the key type used in signing. [chars] is a signed [chars] software\n System identified a mismatch in software type. This might be a modified software. digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-2-MISMATCH_KEYS 2-Critical %%CRITICAL: System identified a mismatch between the show version output and the key type used in signing. [chars] is a signed [chars] software\n System identified a mismatch in software type. This might be a modified software. digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-3-DEVIMAGE_NOSUPPORT 3-Error Cannot verify [chars] as it is signed with special key\n The software image cannot be verified because it is signed with a special key. digi-sign-infra "To allow booting a specially-signed image use the" "software authenticity special command" DIGISIGN-3-DEVIMAGE_NOSUPPORT 3-Error Cannot verify [chars] as it is signed with special key\n The software image cannot be verified because it is signed with a special key. digi-sign-infra "To allow booting a specially-signed image use the" "software authenticity special command" DIGISIGN-3-DEVIMAGE_NOSUPPORT 3-Error Cannot verify [chars] as it is signed with special key\n The software image cannot be verified because it is signed with a special key. digi-sign-infra "To allow booting a specially-signed image use the" "software authenticity special command" DIGISIGN-3-INVALID_ENVELOPE 3-Error %%ERROR: Failure in processing signature envelope for system image: [chars]\n The loaded Cisco IOS software image has an invalid digital signature envelope. A valid digital signature envelope ensures the integrity of the image. The loaded Cisco IOS software image might be corrupted or modified. The failure type is one of the following: 1 Signature envelope version is not supported digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Please attempt to copy the file again or download the file again " "from the http://www.cisco.com page before copying it." "If you continue to get this error message open a case with" "the Technical Assistance Center via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl and " "contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-3-INVALID_ENVELOPE 3-Error %%ERROR: Failure in processing signature envelope for system image: [chars]\n The loaded Cisco IOS software image has an invalid digital signature envelope. A valid digital signature envelope ensures the integrity of the image. The loaded Cisco IOS software image might be corrupted or modified. The failure type is one of the following: 1 Signature envelope version is not supported digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Please attempt to copy the file again or download the file again " "from the http://www.cisco.com page before copying it." "If you continue to get this error message open a case with" "the Technical Assistance Center via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl and " "contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-3-INVALID_ENVELOPE 3-Error %%ERROR: Failure in processing signature envelope for system image: [chars]\n The loaded Cisco IOS software image has an invalid digital signature envelope. A valid digital signature envelope ensures the integrity of the image. The loaded Cisco IOS software image might be corrupted or modified. The failure type is one of the following: 1 Signature envelope version is not supported digi-sign-infra "Do not use this file. The file might be corrupted or modified." "Please attempt to copy the file again or download the file again " "from the http://www.cisco.com page before copying it." "If you continue to get this error message open a case with" "the Technical Assistance Center via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl and " "contact your Cisco technical support representative with the " "image and version information you have gathered." DIGISIGN-3-INVALID_SIGNATURE 3-Error %%ERROR: Digital signature is not valid for file [chars]: [chars]\n The specified Cisco IOS Software image has an invalid digital signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-INVALID_SIGNATURE 3-Error %%ERROR: Digital signature is not valid for file [chars]: [chars]\n The specified Cisco IOS Software image has an invalid digital signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-INVALID_SIGNATURE 3-Error %%ERROR: Digital signature is not valid for file [chars]: [chars]\n The specified Cisco IOS Software image has an invalid digital signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-KEY_NOT_FOUND 3-Error %%ERROR: No keys found for verifying the digital signature in file [chars] No keys found in the device key storage for validating the digital signature. A valid key is needed to validate the digital signature in the image. digi-sign-infra "The device does not have a vlaid key to verify the digital" "signature. Open a case with the Technical Assistance Center" "via the internet at" "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-KEY_NOT_FOUND 3-Error %%ERROR: No keys found for verifying the digital signature in file [chars] No keys found in the device key storage for validating the digital signature. A valid key is needed to validate the digital signature in the image. digi-sign-infra "The device does not have a vlaid key to verify the digital" "signature. Open a case with the Technical Assistance Center" "via the internet at" "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-KEY_NOT_FOUND 3-Error %%ERROR: No keys found for verifying the digital signature in file [chars] No keys found in the device key storage for validating the digital signature. A valid key is needed to validate the digital signature in the image. digi-sign-infra "The device does not have a vlaid key to verify the digital" "signature. Open a case with the Technical Assistance Center" "via the internet at" "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-NET_BOOT 3-Error Netbooted software used for key revocation\n System was netbooted using a software in a remote device. It is recommended to boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-3-NET_BOOT 3-Error Netbooted software used for key revocation\n System was netbooted using a software in a remote device. It is recommended to boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-3-NET_BOOT 3-Error Netbooted software used for key revocation\n System was netbooted using a software in a remote device. It is recommended to boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-3-OBSOLETE_SW 3-Error [chars] software signed using obsolete key [chars]\n System identified that a software was signed using an obsolete key. Key revocation cannot be possible when the system is still using a software signed using an obsolete key. digi-sign-infra "Please obtain the latest signed copy of this " "software from cisco.com and upgrade the system module." DIGISIGN-3-OBSOLETE_SW 3-Error [chars] software signed using obsolete key [chars]\n System identified that a software was signed using an obsolete key. Key revocation cannot be possible when the system is still using a software signed using an obsolete key. digi-sign-infra "Please obtain the latest signed copy of this " "software from cisco.com and upgrade the system module." DIGISIGN-3-OBSOLETE_SW 3-Error [chars] software signed using obsolete key [chars]\n System identified that a software was signed using an obsolete key. Key revocation cannot be possible when the system is still using a software signed using an obsolete key. digi-sign-infra "Please obtain the latest signed copy of this " "software from cisco.com and upgrade the system module." DIGISIGN-3-VERIFICATION_FAILED 3-Error %%ERROR: Digital signature verification failed for file [chars]: [chars]\n Validation failure while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-VERIFICATION_FAILED 3-Error %%ERROR: Digital signature verification failed for file [chars]: [chars]\n Validation failure while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-VERIFICATION_FAILED 3-Error %%ERROR: Digital signature verification failed for file [chars]: [chars]\n Validation failure while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "information you have gathered." DIGISIGN-3-WPG_BOOT 3-Error Key revocation not allowed while running warm upgraded software\n System was booted using warm upgrade. Key revocation process is not supported when the system is booted using warm upgrade. It is recommended to cold boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-3-WPG_BOOT 3-Error Key revocation not allowed while running warm upgraded software\n System was booted using warm upgrade. Key revocation process is not supported when the system is booted using warm upgrade. It is recommended to cold boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-3-WPG_BOOT 3-Error Key revocation not allowed while running warm upgraded software\n System was booted using warm upgrade. Key revocation process is not supported when the system is booted using warm upgrade. It is recommended to cold boot the system using a software in the local device for the key revocation process. digi-sign-infra "Please copy the software to local device. Reboot " "the system with the copied software and retry the key revocation." DIGISIGN-4-DEV_IMAGE 4-Warning [chars] software signed using special key version [chars]\n System identified that a software was signed using special key. If this is unintentional please obtain the latest signed copy of the production software from cisco.com and upgrade the system module. digi-sign-infra "Get the latest signed copy of production image from cisco.com and upgrade " "the respective module" DIGISIGN-4-DEV_IMAGE 4-Warning [chars] software signed using special key version [chars]\n System identified that a software was signed using special key. If this is unintentional please obtain the latest signed copy of the production software from cisco.com and upgrade the system module. digi-sign-infra "Get the latest signed copy of production image from cisco.com and upgrade " "the respective module" DIGISIGN-4-DEV_IMAGE 4-Warning [chars] software signed using special key version [chars]\n System identified that a software was signed using special key. If this is unintentional please obtain the latest signed copy of the production software from cisco.com and upgrade the system module. digi-sign-infra "Get the latest signed copy of production image from cisco.com and upgrade " "the respective module" DIGISIGN-4-DEVIMAGE_CFG_NOSUPPORT 4-Warning [chars] signed with special key will not be booted\n With this configuration enabled the system will be unable to boot software that is signed with a special key. digi-sign-infra "Use the [no] form of this configuration no software authenticity special" DIGISIGN-4-DEVIMAGE_CFG_NOSUPPORT 4-Warning [chars] signed with special key will not be booted\n With this configuration enabled the system will be unable to boot software that is signed with a special key. digi-sign-infra "Use the [no] form of this configuration no software authenticity special" DIGISIGN-4-DEVIMAGE_CFG_NOSUPPORT 4-Warning [chars] signed with special key will not be booted\n With this configuration enabled the system will be unable to boot software that is signed with a special key. digi-sign-infra "Use the [no] form of this configuration no software authenticity special" DIGISIGN-4-FUR_BOOT 4-Warning Field upgradable rommon used for key revocation\n System identified that the field upgradable rommon was used to boot the image. It is recommended that the readonly rommon be used for the key revocation process. digi-sign-infra "Recommended action is to boot the image used for key revocation process " "with readonly rommon. This is a warning message." "Command/process will still go through in the current state." DIGISIGN-4-FUR_BOOT 4-Warning Field upgradable rommon used for key revocation\n System identified that the field upgradable rommon was used to boot the image. It is recommended that the readonly rommon be used for the key revocation process. digi-sign-infra "Recommended action is to boot the image used for key revocation process " "with readonly rommon. This is a warning message." "Command/process will still go through in the current state." DIGISIGN-4-FUR_BOOT 4-Warning Field upgradable rommon used for key revocation\n System identified that the field upgradable rommon was used to boot the image. It is recommended that the readonly rommon be used for the key revocation process. digi-sign-infra "Recommended action is to boot the image used for key revocation process " "with readonly rommon. This is a warning message." "Command/process will still go through in the current state." DIGISIGN-4-INVALID_KEY 4-Warning %%WARNING: Digital signature verification failed for file [chars]: [chars]\n Validation failure due to invalid key while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "device information you have gathered." DIGISIGN-4-INVALID_KEY 4-Warning %%WARNING: Digital signature verification failed for file [chars]: [chars]\n Validation failure due to invalid key while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "device information you have gathered." DIGISIGN-4-INVALID_KEY 4-Warning %%WARNING: Digital signature verification failed for file [chars]: [chars]\n Validation failure due to invalid key while verifying the digital signature. digi-sign-infra "Do not use this file. The file might be corrupted or " "modified. Please attempt to copy the file again or download " "the file again from the http://www.cisco.com page before " "copying it. If you continue to get this error message " "open a case with the Technical Assistance Center via the " "Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl " "and contact your Cisco technical support representative with the " "device information you have gathered." DIGISIGN-4-SIGNATURE_NOT_PRESENT 4-Warning %%WARNING: Digital signature is not found in file [chars]\n The specified image file does not have a digital signature. Only Cisco IOS Software Images are digitally signed. If you enter verify copy or reload command and the specified file is not a digitally signed Cisco IOS Software Image the system displays this warning message because the file does not have a signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "If the specified file is an unsigned Cisco IOS Software image " "be cautious when deciding " "whether or not to use this file. The system will not boot using " "this image." DIGISIGN-4-SIGNATURE_NOT_PRESENT 4-Warning %%WARNING: Digital signature is not found in file [chars]\n The specified image file does not have a digital signature. Only Cisco IOS Software Images are digitally signed. If you enter verify copy or reload command and the specified file is not a digitally signed Cisco IOS Software Image the system displays this warning message because the file does not have a signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "If the specified file is an unsigned Cisco IOS Software image " "be cautious when deciding " "whether or not to use this file. The system will not boot using " "this image." DIGISIGN-4-SIGNATURE_NOT_PRESENT 4-Warning %%WARNING: Digital signature is not found in file [chars]\n The specified image file does not have a digital signature. Only Cisco IOS Software Images are digitally signed. If you enter verify copy or reload command and the specified file is not a digitally signed Cisco IOS Software Image the system displays this warning message because the file does not have a signature. A valid digital signature ensures the integrity of the image. digi-sign-infra "If the specified file is an unsigned Cisco IOS Software image " "be cautious when deciding " "whether or not to use this file. The system will not boot using " "this image." DIGISIGN-6-KEY_UPGRADE 6-Information [chars]\n System identified a key version mismatch between the key which was used to sign the image and the keys stored on the device digi-sign-infra "If the image is signed with a key version newer than the device" "keys then follow the procedure for key revocation which is" "which is documented at cisco.com. If the image is signed with a" "key version that is now obsolete please obtain the latest signed" "copy of this image from cisco.com" DIGISIGN-6-KEY_UPGRADE 6-Information [chars]\n System identified a key version mismatch between the key which was used to sign the image and the keys stored on the device digi-sign-infra "If the image is signed with a key version newer than the device" "keys then follow the procedure for key revocation which is" "which is documented at cisco.com. If the image is signed with a" "key version that is now obsolete please obtain the latest signed" "copy of this image from cisco.com" DIGISIGN-6-KEY_UPGRADE 6-Information [chars]\n System identified a key version mismatch between the key which was used to sign the image and the keys stored on the device digi-sign-infra "If the image is signed with a key version newer than the device" "keys then follow the procedure for key revocation which is" "which is documented at cisco.com. If the image is signed with a" "key version that is now obsolete please obtain the latest signed" "copy of this image from cisco.com" DIRECTOR-3-BADCOMPL 3-Error plug-in returned orphan status A software or hardware error occurred. dist-director "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIRECTOR-3-DRPDOWN 3-Error DRP [inet] was down %TE ago in the last [dec] minute period ! There may be problems related to this DRP agent. The remote DRP agent has not responded within the time period reported - "Make sure the remote DRP agent is running and that it is accessible\n\ from the system reporting the problem." DIRECTOR-3-HTTPOVERLOAD 3-Error Excessive HTTP request overloading: dropping HTTP req from . HTTP requests are overloading the web redirector dist-director "Web redirector is automatically discarding HTTP request traffic." DIRECTOR-3-NOALIAS 3-Error [chars] can not create ip alias Most likely a resource problem within the system. dist-director "Reboot the system as soon as possible. If the problem continues\n\ to occur report it to your technical support representative." DIRECTOR-3-NOPORT 3-Error [chars] port in use The IP address requested has been found to be already in use on\n\ some interface connected to the system or within the system itself. dist-director "Either select another IP address for use or locate the system making\n\ use of this address and reconfigure it to use another." DIRECTOR-3-NOPROC 3-Error unable to create [chars] process Most likely a resource problem within the system. dist-director "Reboot the system as soon as possible. If the problem continues\n\ to occur report it to your technical support representative." DIRECTOR-3-NOSOCKET 3-Error [chars] unable to create socket A software or hardware error occurred. dist-director "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIRECTOR-3-NOTCONF 3-Error Metric [chars] referenced but not found - dist-director - DIRECTOR-3-NOWRITE 3-Error [chars] unable to write to socket A software or hardware error occurred. dist-director "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DIRECTOR-3-URLELSEWHERE 3-Error URL is elsewhere '[chars]' Code [dec] - [chars] The HTTP return code indicates the page is not actually on this server dist-director "Check the URL configured. Check the configured HTTP server." DIRECTOR-3-URLSVRERR 3-Error Server error '[chars]' Code [dec] - [chars] The HTTP return code indicates a server failure error dist-director "Check the URL configured. Check the configured HTTP server." DIRECTOR-5-SVRUPDOWN 5-Notice server [inet] on port [dec] has gone [chars] The remote server has gone up or down dist-director "None." DIRECTOR-6-DNSNORSP 6-Information answer type [chars] host [chars] cli [inet] id# [dec] none DNS reply logging: no server found. dist-director "None." DIRECTOR-6-DNSQUERY 6-Information query type [chars] host [chars] cli [inet] id# [dec] DNS query logging. dist-director "None." DIRECTOR-6-DNSRESPN 6-Information answer type [chars] host [chars] cli [inet] id# [dec] svr [inet] DNS reply logging with server found. dist-director "None." DIRECTOR-6-SVRNSELCT 6-Information no answer for host [chars] cli [inet] type [chars] id# [dec] [chars] No server found. dist-director "None." DIRECTOR-6-SVRSELECT 6-Information select [inet] host [chars] cli [inet] type [chars] id# [dec] [chars] Report server selection process. dist-director "None." DISPOSITION_DISABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - DISPOSITION_DISABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - DISPOSITION_ENABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - DISPOSITION_ENABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - DLC-2-NOMEMORY 2-Critical no memory for [chars] There was not enough free memory to complete the operation. - LOG_STD_ACTION DLC-3-BADPARAM 3-Error Function [chars]: value [hex] passed in parameter [chars] An internal software error occurred. - LOG_STD_ACTION DLC-3-INVPCEP 3-Error Close Station invalid P_CEP An internal software error occurred. - LOG_STD_ACTION DLC-3-WPUTERR 3-Error unknown port type [hec] An internal software error occurred. - LOG_STD_ACTION DLEP_MSG-4-CONNECT_ERROR 4-Warning TCP connect to Radio [inet] failed via [chars]. Error code: [chars] TCP Connect to IP address and port of the Radio failed. DLEP_DDTS_COMPONENT "Take action based on the error code shown." " Reconfigure correct IP address and port " " if necessary." DLEP_SET_MSG-6-DLEP_HEARTBEAT_THRESHOLD 6-Information new Threshold value configured will have effect for the new sessions only not for the currently running DLEP sessions If the threshold value should be updated at Router side it must be configured before the Radio launch dlep "Once the DLEP session is established and if you" " want to change the threshold value kill the" " Radio and reconfigure the dlep on Router" " interface and make the Radio UP to see" " the updated threshold value " DLEP_SET_MSG-6-DLEP_NBR_ACTIVITY_TIMEOUT 6-Information new nbr-activity-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions If the nbr-activity-timeout value should be updated at Router side it must be configured before the Radio launch dlep "Once the DLEP session is established and if you" " want to change the nbr-activity-timeout value" " kill the Radio and reconfigure the dlep on" " Router interface and make the Radio UP to see" " the updated value " DLEP_SET_MSG-6-DLEP_NBR_DOWN_ACK_TIMEOUT 6-Information new nbr-down-ack-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions If the nbr-down-ack-timeout value should be updated at Router sideit must be configured before the Radio launch dlep "Once the DLEP session is established and if you want" " to change the nbr-down-ack-timeout value kill the " "Radio and reconfigure the dlep on Router interface " "and make the Radio UP to see the updated Value " DLEP_SET_MSG-6-DLEP_PEER_TERMINATE_ACK_TIMEOUT 6-Information new peer-terminate-ack-timeout value configured will have effect for the new sessions only not for the currently running DLEP sessions If the peer-terminate-ack-timeout value should be updated Router side it must be configured before the Radio launch dlep "Once the DLEP session is established and if you want" " to change the peer-terminate-ack-timeout value" " kill the Radio and reconfigure the dlep on Router" " interface and make the Radio UP to see the updated value " DLINK-3-BAD_QELEM 3-Error Bad queue elem - %08x: flink %08x blink %08x flink->blink %08x blink->flink %08x An internal software error occurred. DLINK_UTIL_DDTS_COMPONENT LOG_STD_RECUR_ACTION DLINK-3-NULL_QELEM 3-Error Null queue elem An internal software error occurred. DLINK_UTIL_DDTS_COMPONENT LOG_STD_RECUR_ACTION DLR-2-GWFAULT 2-Critical Ring [dec]: The redundant gateway device is now in FAULT state The redundant gateway device is in fault state accsw-layer2 "A redundant gateway device goes to fault state if " "all its uplinks are down. Check the status of all uplinks. Restore the connection if possible." DLR-2-GWPARTIALFAULT 2-Critical Ring [dec]: The redundant gateway device is now in PARTIAL FAULT state The redundant gateway is in partial fault state accsw-layer2 "A redundant gateway device goes to partial fault " "state if it receives messages indicating that a redundant gateway device with lower precedence" " is active. Make sure that there's bidirectional connectivity between all redundant gateway devices" " and then clear the partial fault condition." DLR-2-MACFAILURE 2-Critical Ring [dec]: [chars] Failed to update the supervisor MAC. accsw-layer2 "Remove and reconfigure the DLR ring. Make sure that a VLAN interface has been created for the VLAN that " "the ring ports belong to. Contact TAC if the problem persists." DLR-2-NOPROC 2-Critical Failed to start [chars] process [chars] Unable to create DLR process. Reloading the device might resolve the issue. Without a reload DLR will not function properly. accsw-layer2 "Reload the device" DLR-2-RINGFAULT 2-Critical Ring [dec]: The DLR ring is now in FAULT state The DLR ring is in FAULT state. This typically happens if a link or node in the ring goes down. accsw-layer2 "Determine the location of the fault and restore " "connectivity. The ring should resume functioning automatically" DLR-2-SUPPARTIALFAULT 2-Critical Ring [dec]: The supervisor device is now in PARTIAL FAULT state The supervisor device goes to partial fault state if it detects loss of beacon frames in one direction only. accsw-layer2 "Determine the source of the problem and fix it. The device will resume normal operation automatically." DLR-2-SUPRAPIDFAULT 2-Critical Ring [dec]: The supervisor device is now in RAPID FAULT state The supervisor device is in fault state. This happens if the device transitions from Normal to Fault state more than 5 times in 30 seconds. accsw-layer2 "Locate the source of the faults and fix the problem before clearing the rapid fault condition" DLR-3-EVENTFAILURE 3-Error [chars] A DLR event could not be handled properly. accsw-layer2 "It could have been a temporary condition. Remove " "and reconfigure the DLR ring if the problem persists." DLR-3-GWCFGFAIL 3-Error Ring [dec]: [chars] There was an issue with the DLR redundant gateway configuration. The redundant gateway may not function properly. accsw-layer2 "Remove and reconfigure DLR redundant gateway functionality. Contact TAC if the problem persists." DLR-3-GWUPLNKCFGFAIL 3-Error Ring [dec]: [chars] There was an issue with the DLR redundant gateway uplink configuration. The redundant gateway may not function properly. accsw-layer2 "Remove and reconfigure DLR redudant gateway " "uplink configuration from the interface. Contact TAC if the problem persists." DLR-3-RINGCFGFAIL 3-Error Ring [dec]: [chars] There was an issue with the DLR ring configuration. The ring may not function properly. accsw-layer2 "Remove and reconfigure the DLR ring. Contact TAC if the problem persists." DLR-3-SWSWITCH 3-Error Ring [dec]: [chars] frames are being software switched Frames which should be hardware switched are being software switched. It's normal to see this message once or twice during configuration changes but not otherwise. It can make the ring unstable and drive up the CPU utilization. accsw-layer2 "Remove and reconfigure the DLR ring. Contact TAC if the problem persists." DLR-6-GWSTATECHG 6-Information Ring [dec]: The device is now the [chars] redundant gateway The state of redundant gateway has changed accsw-layer2 "This is an informational message. The device is functioning as expected." DLR-6-RINGNORMAL 6-Information Ring [dec]: The DLR ring is now in NORMAL state The state of the DLR ring has changed to NORMAL. accsw-layer2 "This is an informational message. The device is functioning as expected." DLR-6-SUPSPTPARAM 6-Information Ring [dec]: Supported beacon parameters received This backup supervisor received beacons with supported parameters from active supervisor which can be supported by this device. accsw-layer2 "This backup supervisor device can take the role of active supervisor with current beacon parameters." DLR-6-SUPSTATECHG 6-Information Ring [dec]: The device is now the [chars] supervisor The state of the supervisor device has changed accsw-layer2 "This is an informational message. The device is functioning as expected." DLR-6-SUPUNSPTPARAM 6-Information Ring [dec]: Unsupported beacon parameters received This backup supervisor received beacons with parameters from active supervisor which cannot be supported by this device. accsw-layer2 "This backup supervisor device cannot take the " "role of active supervisor with current beacon parameters." DLSWC-3-BADCLSI 3-Error [chars] primitive not valid for dlsw [chars] [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADCLSICNF 3-Error [chars] Invalid confirm [chars] [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADCLSIIND 3-Error [chars] Invalid indication [chars] [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADCLSIRET 3-Error [chars] Invalid ret code 0x[hec] [chars] [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADCLSISAP 3-Error [chars] Bad clsi SAP id = [hec] [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADPEEROP 3-Error bad peer op in peer_to_core [dec] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-BADSSPHDR 3-Error bad ssp hdr in proc ssp - [chars] = 0x[hec] - - "If the remote peer is a nonCisco router confirm that it supports the\n\ DLSw RFC 1795 standard." DLSWC-3-IDMGR 3-Error [chars] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-NODLSW 3-Error [chars] [dec] A data-link switching system error occurred. - LOG_STD_ACTION DLSWC-3-NOPEER 3-Error [chars] A data-link switching system error occurred. - LOG_STD_RECUR_ACTION DLSWC-3-RECVSSP 3-Error SSP OP = [dec][chars] [chars] from [chars] - - LOG_STD_NO_ACTION DLSWC-3-SENDSSP 3-Error SSP OP = [dec][chars] [chars] to [chars] [chars] A Silicon Switch Program SSP frame was sent to the remote peer. - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMS 3-Error [chars] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSCSM 3-Error [chars] [chars] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSDLX 3-Error [chars] [hec] from [enet] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSFSM 3-Error [chars]: [chars] from [enet] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSRCV 3-Error [chars] from [enet] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSSAP 3-Error [chars]: [chars] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWMasterSlave-3-DLSWMSTX 3-Error [chars]: [chars] to [enet] DLSw Master-Slave Error - LOG_STD_NO_ACTION DLSWP-3-PBADVALUE 3-Error [chars]: invalid [chars] [dec] A bad parameter value was passed to function chars1 - invalid\n\ parameter chars2 with value. This error should not cause any network\n\ problems unless it happens repeatedly. - LOG_STD_ACTION DLSWP-3-PCAPMISMATCH 3-Error [chars]: [chars] The largest frame size configured in the DLSW remote peer definition\n\ is being changed because the MTU size configured\n\ on the interface used by DLSW is less than the configured value of\n\ the largest frame on DLSW remote peer definition. The largest frame size\n\ is being changed to that configured on the interface. - "If you wish to use this largest frame size for DLSW increase the\n\ MTU on the interface to a value larger than the configured largest\n\ frame size." DLSWP-3-PEERFAILURE 3-Error [chars] [chars] A DLSW peer failed:\n\\n\ - keepalive failure dlsw between cisco peers is sending a peer keepalive\n\ by default every 30 sec. After missing 3 consecutive keepalives the peer\n\ is taken down.\n\ - We are not promiscuous Rej conn from peer a.b.c.d\n\ The local dlsw peer is not configured for promiscuous and we receive\n\ a request to open a dlsw peer for which we have no corresponding dlsw\n\ remote peer statement.\n\ - received tcp fini dlsw peer code has received a tcp fini from the \n\ underlaying tcp subsystem. To obey the tcp fini dlsw wring bring down \n\ the peer connection for which the tcp fini was received. - "- keepalive failure\n\ Check end to end connectivity between the DLSW peers\n\ - We are not promiscuous Rej conn from peer a.b.c.d\n\ correct your configuration. \n\ - received tcp fini\n\ Check the underlaying tcp connection between the two dlsw peers." DLSWP-3-PGENERAL 3-Error [chars] A general error condition was detected as described in the message\n\ text. This error should not cause any network problems unless it\n\ happens repeatedly. - LOG_STD_ACTION DLSWP-3-PNOCOOKIE 3-Error uninitalized peer [chars] from [inet][dec] to [inet][dec] DLSw received a packet on an uninitialized peer connection. - "Verify configuration and DLSw peer status on both routers". DLSWP-3-PNOMEM 3-Error No memory to [chars] The router ran out of system memory for operation as described in the\n\ message text. Most likely the router image requires more system memory\n\ RAM than the router contains. - "Consult with your Cisco technical support representative\n\ about memory requirements for a specific image." DLSWP-3-PPASSIVE 3-Error passive open failed from [inet][dec] -> [dec] - - "Consult with your Cisco technical support representative\n\ about memory requirements for a specific image." DLSWP-5-PEERUPDOWN 5-Notice [chars] [chars] A DLSW peer is either connected or disconnected - "None informational message only." DMA-1-DRQ_EMPTY_PAK 1-Alert Empty packet is being sent to backplane. particle_ptr=[hex] drq_io receives a packet that has particle count 0. coding error --\n\ hurt performance high-vip2 "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the\n\ show log on the reporting VIP" DMA-1-DRQ_STALLED 1-Alert DRQ stalled. Dumping DRQ. The path from VIP to backplane has stalled. The DRQ table is \n\ being dumped for debugging high-vip2 "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the hex\n\ dump following this message" DMA-1-LOW_DMA_PCI_MEM 1-Alert Not enough pci memory left over for DMA Misconfiguration has resulted in overutilization of PCI memory high-vip2 "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of show diag and show controller cbus" DMA-1-LOW_DMA_PROC_MEM 1-Alert Not enough processor memory left over for DMA This error message appears only in custom built images when a sanity\n\ check fails. A packet that was too large was sent over the backplane\n\ by a VIP. high-vip2 "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of show tech." DMA-3-DTQ_DISPATCH_DIRTY_PAK 3-Error pak not cleaned up by Egress processing appId [dec] After dtq dispatched a packet to Egress processing packet is not cleaned up by application high-vip2 "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the\n\ show log on the reporting VIP" DMB-0-DMB_EMERG 0-Emergency [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-0-DMB_EMERG 0-Emergency [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-1-DMB_ALERT 1-Alert [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-1-DMB_ALERT 1-Alert [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-2-DMB_CRIT 2-Critical [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-2-DMB_CRIT 2-Critical [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-3-DMB_ERR 3-Error [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-3-DMB_ERR 3-Error [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-4-DMB_WARNING 4-Warning [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-4-DMB_WARNING 4-Warning [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-5-DMB_NOTICE 5-Notice [chars] Normal but significant conditions DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-5-DMB_NOTICE 5-Notice [chars] Normal but significant conditions DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-6-DMB_INFO 6-Information [chars] Informational messages DMB_DDTS_COMPONENT LOG_STD_NO_ACTION DMB-6-DMB_INFO 6-Information [chars] Informational messages DMB_DDTS_COMPONENT LOG_STD_NO_ACTION DMB-7-DMB_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMB-7-DMB_ASSERT 7-Debug Assertion Failure [chars] @[chars]:[dec] : [chars] DMB_INTERNAL_ERROR DMB_DDTS_COMPONENT LOG_STD_ACTION DMTDSL-1-INITFAIL 1-Alert DMTDSL[dec]/[dec] Init failed [chars] The ADSL network module hardware may be bad - LOG_STD_ACTION DMTDSL-3-BADINITDSL 3-Error DMTDSL[dec]/[dec]interface not initialized. The ATM network module hardware may be bad pm-atm25 LOG_STD_ACTION DMTDSL-3-DMTHWBAD 3-Error DMTDSL[dec]/[dec] Hardware failed self test The DSL chipset failed its self test - LOG_STD_ACTION DMTDSL-3-FAILFINDATM 3-Error DMTDSL Could not find ATM interface. The DSL network module hardware may be bad pm-atm25 LOG_STD_ACTION DMTDSL-3-NOMEM 3-Error DMTDSL[dec]/[dec] Out of memory The router does not have enough memory installed to run this image - LOG_STD_ACTION DMVPN-3-DMVPN_NHRP_ERROR 3-Error [chars]: [chars] [chars] Reason: [chars] [dec] on Tunnel: [chars] NBMA: [chars] NHRP Error messages nhrp LOG_STD_ACTION DMVPN-3-DMVPN_NHRP_ERROR 3-Error [chars]: [chars] [chars] Reason: [chars] [dec] on Tunnel: [chars] NBMA: [chars] NHRP Error messages nhrp LOG_STD_ACTION DMVPN-3-DMVPN_NHRP_MULTICAST_ERR 3-Error [chars]: [chars] on Tunnel: [chars] NBMA: [chars] NHRP Multicast Replication Error messages nhrp LOG_STD_ACTION DMVPN-3-DMVPN_NHRP_MULTICAST_ERR 3-Error [chars]: [chars] on Tunnel: [chars] NBMA: [chars] NHRP Multicast Replication Error messages nhrp LOG_STD_ACTION DMVPN-3-NHRP_ERROR 3-Error [chars]: [chars] failed for [chars] [chars] [dec] for Tunnel: [chars] NBMA: [chars] on Tunnel: [chars] NBMA: [chars] Unable to send/receive packets. nhrp LOG_STD_ACTION DMVPN-3-NHRP_ERROR 3-Error [chars]: [chars] failed for [chars] [chars] [dec] for Tunnel: [chars] NBMA: [chars] on Tunnel: [chars] NBMA: [chars] Unable to send/receive packets. nhrp LOG_STD_ACTION DMVPN-3-NHRP_REGISTRATION_ERROR 3-Error [chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars] NHRP Registration send/receive Error Indication packets. nhrp LOG_STD_ACTION DMVPN-3-NHRP_REGISTRATION_ERROR 3-Error [chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars] NHRP Registration send/receive Error Indication packets. nhrp LOG_STD_ACTION DMVPN-3-NHRP_RESOLUTION_ERROR 3-Error [chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars] NHRP Resolution send/receive Error Indication packets. nhrp LOG_STD_ACTION DMVPN-3-NHRP_RESOLUTION_ERROR 3-Error [chars]: [chars] [chars] Error indication for [chars] - [chars][dec] Src Tunnel: [chars] NBMA: [chars] Dest Tunnel: [chars] NBMA: [chars] NHRP Resolution send/receive Error Indication packets. nhrp LOG_STD_ACTION DMVPN-4-NHRP_QUOTA 4-Warning [chars]: Max-send Quota of [dec]pkts/[dec]sec exceeded on Tunnel: [chars] NBMA: [chars] nhrp quota exceeded nhrp LOG_STD_ACTION DMVPN-4-NHRP_QUOTA 4-Warning [chars]: Max-send Quota of [dec]pkts/[dec]sec exceeded on Tunnel: [chars] NBMA: [chars] nhrp quota exceeded nhrp LOG_STD_ACTION DMVPN-5-CRYPTO_SS 5-Notice [chars]: local address : [chars] remote address : [chars] socket is [chars] DMVPN Crypto UP/DOWN Syslog Event nhrp LOG_STD_ACTION DMVPN-5-CRYPTO_SS 5-Notice [chars]: local address : [chars] remote address : [chars] socket is [chars] DMVPN Crypto UP/DOWN Syslog Event nhrp LOG_STD_ACTION DMVPN-5-NHRP_NETID_UNCONFIGURED 5-Notice [chars]: NETID : [dec] [chars] Tunnel: [chars] NBMA: [chars] NETID Unconfigured nhrp LOG_STD_ACTION DMVPN-5-NHRP_NETID_UNCONFIGURED 5-Notice [chars]: NETID : [dec] [chars] Tunnel: [chars] NBMA: [chars] NETID Unconfigured nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHC_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHC_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHC_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHC_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHP_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Peer changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHP_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Peer changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHP_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Peer changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHP_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Peer changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHS_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHS_DOWN 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Reason: [chars]NHRP: [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHS_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_NHS_UP 5-Notice [chars]: Next Hop [chars] : Tunnel: [chars] NBMA: [chars] for Tunnel: [chars] NBMA: [chars] is [chars] Next Hop Client changed the state. nhrp LOG_STD_ACTION DMVPN-5-NHRP_RES_REPLY 5-Notice [chars]: [chars] [chars] sent via Tunnel: [chars] NBMA: [chars] to Tunnel: [chars] NBMA: [chars] A NHRP Resolution Reply sent via the NHS Path nhrp LOG_STD_ACTION DMVPN-5-NHRP_RES_REPLY 5-Notice [chars]: [chars] [chars] sent via Tunnel: [chars] NBMA: [chars] to Tunnel: [chars] NBMA: [chars] A NHRP Resolution Reply sent via the NHS Path nhrp LOG_STD_ACTION DMVPN-5-NHRP_RES_REPLY_IGNORE 5-Notice [chars]: resolution reply received on [chars] for dst : [chars] is dropped crypto session failed to come up A NHRP Resolution Reply received through Hub which is dropped - crypto session failed to come up nhrp LOG_STD_ACTION DMVPN-5-NHRP_RES_REPLY_IGNORE 5-Notice [chars]: resolution reply received on [chars] for dst : [chars] is dropped crypto session failed to come up A NHRP Resolution Reply received through Hub which is dropped - crypto session failed to come up nhrp LOG_STD_ACTION DMVPN-5-NHRP_ROUTING 5-Notice Peer with Tunnel: [chars] NBMA: [chars] on [chars] [chars] with Reason :[chars] . A short cut switching entry has been created nhrp LOG_STD_ACTION DMVPN-5-NHRP_ROUTING 5-Notice Peer with Tunnel: [chars] NBMA: [chars] on [chars] [chars] with Reason :[chars] . A short cut switching entry has been created nhrp LOG_STD_ACTION DMVPN-6-NHRP_RES_TIMEOUT 6-Information [chars]: [chars] for Address : [chars] is Timed-out A NHRP Resolution Request has timed-out nhrp LOG_STD_ACTION DMVPN-6-NHRP_RES_TIMEOUT 6-Information [chars]: [chars] for Address : [chars] is Timed-out A NHRP Resolution Request has timed-out nhrp LOG_STD_ACTION DMVPN-6-NHRP_RESOLUTION_REPLY 6-Information [chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars] A NHRP Resolution Reply has been received nhrp LOG_STD_ACTION DMVPN-6-NHRP_RESOLUTION_REPLY 6-Information [chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars] A NHRP Resolution Reply has been received nhrp LOG_STD_ACTION DMVPN-7-NHRP_EVENT 7-Debug [chars]: [chars] [chars] [chars] [chars] [chars] A Registration/Resolution Request/Reply Received/Sent nhrp LOG_STD_ACTION DMVPN-7-NHRP_EVENT 7-Debug [chars]: [chars] [chars] [chars] [chars] [chars] A Registration/Resolution Request/Reply Received/Sent nhrp LOG_STD_ACTION DMVPN-7-NHRP_RES 7-Debug [chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars] A NHRP Resolution Request has been received nhrp LOG_STD_ACTION DMVPN-7-NHRP_RES 7-Debug [chars]: Host with Tunnel: [chars] NBMA: [chars] [chars] Tunnel: [chars] NBMA: [chars] A NHRP Resolution Request has been received nhrp LOG_STD_ACTION DNET-3-HEARSELF 3-Error Hello type [hec] for my address from [dec].[dec] via [chars] The system is receiving its own DECnet packets. Either a serial line\n\ is looped back or another host with the same DECnet address is already\n\ present on the LAN. - "Check the serial lines if present and the DECnet configuration." DNET-3-NOMEMORY 3-Error Insufficient memory for DECnet accounting entry The traffic information for a particular pair of DECnet nodes \n\ cannot be recorded due to a low memory condition. decnet LOG_STD_REDUCE_ACTION DNET-4-DUPENTRY 4-Warning Duplicate DECnet Accounting List Entry for nodes [dec].[dec] - [dec].[dec] A synchronization problem has occurred whilst a new transit \n\ DECnet Accounting List Entry was being added and a duplicate entry\n\ has been found. decnet show decnet accounting DNET-4-MAPCON 4-Warning Map entry [dec].[dec] conflicts with adjacency to [dec].[dec] Your DECnet configuration is incorrect. A host that is specified as\n\ nonlocal is present on your local network. - "Correct the configuration. Call your technical support representative\n\ if you need assistance." DNLD-3-ERROR 3-Error [chars] Error on DNLD module. - LOG_STD_SH_TECH_ACTION DNLD-3-ERROR 3-Error [chars] Error on DNLD module. - LOG_STD_SH_TECH_ACTION DNLD-6-DSPFARM_REGISTER_FAILED 6-Information Failed to register DNLD Application with DSPFARM\n Failed to register DNLD Application with DSPFARM. - LOG_STD_SH_TECH_ACTION DNLD-6-DSPFARM_REGISTER_FAILED 6-Information Failed to register DNLD Application with DSPFARM\n Failed to register DNLD Application with DSPFARM. - LOG_STD_SH_TECH_ACTION DNSSERVER-3-BADQUERY 3-Error Bad DNS query from [inet] A client sent a DNS query to the server which has been found to be incorrectly formatted. - "Check the DNS server and the network attached to it." DNSSERVER-3-NOINIT 3-Error Can't initialize DNS server Internal problems with initializing ports for the DNS server - "Make sure the DNS server port is available on the local machine." DNSSERVER-3-TCPDNSOVERLOAD 3-Error Low available memory: dropping TCP request from . There is not enough free memory to handle DNS queries. - "DNS server is automatically discarding DNS request traffic." DNSSERVER-3-TOOSHORT 3-Error DNS query from [inet] too short A client sent a short DNS query packet to the server - "Check the client and the network attached to it." DNSSERVER-3-UDPDNSOVERLOAD 3-Error Low available memory: dropping from . There is not enough free memory to handle DNS queries. - "DNS server is automatically discarding DNS request traffic." DOMAIN-2-GLOBALS_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing global parameters ng-pfr "Check if software versions are compatible" DOMAIN-2-GLOBALS_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing global parameters ng-pfr "Check if software versions are compatible" DOMAIN-2-IME 2-Critical Immitigable event occured. IME-ID=[dec]: Details: [chars]\n Error encounterd during TCA processing. The flow could not be placed on alternate path. ng-pfr "Troubleshoot the network for performance/bandwidth issues." DOMAIN-2-IME 2-Critical Immitigable event occured. IME-ID=[dec]: Details: [chars]\n Error encounterd during TCA processing. The flow could not be placed on alternate path. ng-pfr "Troubleshoot the network for performance/bandwidth issues." DOMAIN-2-IME_DETAILS 2-Critical IME-ID=[dec]: [chars]\n Error encounterd during TCA processing. The flow could not be placed on alternate path. ng-pfr "Troubleshoot the network for performance/bandwidth issues." DOMAIN-2-IME_DETAILS 2-Critical IME-ID=[dec]: [chars]\n Error encounterd during TCA processing. The flow could not be placed on alternate path. ng-pfr "Troubleshoot the network for performance/bandwidth issues." DOMAIN-2-PMI_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing pmi parameters ng-pfr "Check if software versions are compatible" DOMAIN-2-PMI_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing pmi parameters ng-pfr "Check if software versions are compatible" DOMAIN-2-POLICY_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing policy definition ng-pfr "On Hub MC check if invalid characters are used in policy name" DOMAIN-2-POLICY_XML_FAILURE 2-Critical [chars] Failed to decode xml message containing policy definition ng-pfr "On Hub MC check if invalid characters are used in policy name" DOMAIN-3-HUB_SITE_ID_ERR 3-Error [chars] Hub site-id error notification. ng-pfr "Correct the Hub MC ip-address configuration" DOMAIN-3-HUB_SITE_ID_ERR 3-Error [chars] Hub site-id error notification. ng-pfr "Correct the Hub MC ip-address configuration" DOMAIN-3-INVALID_EXIT 3-Error [chars] Inavlid Exit notification. ng-pfr "Correct the PLR interface configuration" DOMAIN-3-INVALID_EXIT 3-Error [chars] Inavlid Exit notification. ng-pfr "Correct the PLR interface configuration" DOMAIN-3-PLR_INT_CFG 3-Error [chars] Conflicting Domain configuration exists on the selected WAN interface on border. ng-pfr "Correct the domain path configuration on selected WAN interface on border and retry." DOMAIN-3-PLR_INT_CFG 3-Error [chars] Conflicting Domain configuration exists on the selected WAN interface on border. ng-pfr "Correct the domain path configuration on selected WAN interface on border and retry." DOMAIN-4-BR_SHUTDOWN 4-Warning Reason=[chars] Border Shutdown Warning Message. ng-pfr LOG_STD_NO_ACTION DOMAIN-4-BR_SHUTDOWN 4-Warning Reason=[chars] Border Shutdown Warning Message. ng-pfr LOG_STD_NO_ACTION DOMAIN-4-DCA_DOMAIN_MAP 4-Warning [chars] DCA domain map error notification. ng-pfr "Correct the branch MC domain-map configuration." DOMAIN-4-DCA_DOMAIN_MAP 4-Warning [chars] DCA domain map error notification. ng-pfr "Correct the branch MC domain-map configuration." DOMAIN-4-MC_SHUTDOWN 4-Warning Reason=[chars] Master Controller Shutdown Warning Message. ng-pfr LOG_STD_NO_ACTION DOMAIN-4-MC_SHUTDOWN 4-Warning Reason=[chars] Master Controller Shutdown Warning Message. ng-pfr LOG_STD_NO_ACTION DOMAIN-4-PDP_PREFIX_REACH 4-Warning [chars] Prefix not reachable on the channel ng-pfr "Verify the reachability of the prefix" DOMAIN-4-PDP_PREFIX_REACH 4-Warning [chars] Prefix not reachable on the channel ng-pfr "Verify the reachability of the prefix" DOMAIN-4-SITE_PREFIX 4-Warning [chars] Improper site prefix configuration detected. ng-pfr "Correct your site prefix configuration" DOMAIN-4-SITE_PREFIX 4-Warning [chars] Improper site prefix configuration detected. ng-pfr "Correct your site prefix configuration" DOMAIN-4-SMP 4-Warning [chars] Smart-Probe config is being changed ng-pfr LOG_STD_NO_ACTION DOMAIN-4-SMP 4-Warning [chars] Smart-Probe config is being changed ng-pfr LOG_STD_NO_ACTION DOMAIN-4-TUN_SRC_OVERLAPPED 4-Warning [chars] Tunnel source overlapped notification. ng-pfr "Correct the source configuration." DOMAIN-4-TUN_SRC_OVERLAPPED 4-Warning [chars] Tunnel source overlapped notification. ng-pfr "Correct the source configuration." DOMAIN-4-WAN_INTERFACE 4-Warning Interface \[chars]\ received probes but no \dynamic-path\ configured - - - DOMAIN-4-WAN_INTERFACE 4-Warning Interface \[chars]\ received probes but no \dynamic-path\ configured - - - DOMAIN-4-WAN_INTERFACE_TYPE_CONFLICT 4-Warning Interface \[chars]\ discoveried as WAN interface. But DCA already configured. Branch site border router WAN interface must have dynamic-path configured ng-pfr "configure domain dynamic-path on WAN interface" DOMAIN-4-WAN_INTERFACE_TYPE_CONFLICT 4-Warning Interface \[chars]\ discoveried as WAN interface. But DCA already configured. Branch site border router WAN interface must have dynamic-path configured ng-pfr "configure domain dynamic-path on WAN interface" DOMAIN-5-BR_STATUS 5-Notice [chars] Border Status Notification. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-BR_STATUS 5-Notice [chars] Border Status Notification. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-MC_STATUS 5-Notice [chars] Master Controller Status Notification. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-MC_STATUS 5-Notice [chars] Master Controller Status Notification. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-TC_PATH_CHG 5-Notice Traffic class Path Changed. Details: [chars]\n A Path chage is made. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-TC_PATH_CHG 5-Notice Traffic class Path Changed. Details: [chars]\n A Path chage is made. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-TCA 5-Notice [chars] Received. Details: [chars]\n A threshold crossing alarm is raised. ng-pfr LOG_STD_NO_ACTION DOMAIN-5-TCA 5-Notice [chars] Received. Details: [chars]\n A threshold crossing alarm is raised. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-INIT 6-Information [chars] Informational Message. Domain master controller initialization completed ng-pfr LOG_STD_NO_ACTION DOMAIN-6-INIT 6-Information [chars] Informational Message. Domain master controller initialization completed ng-pfr LOG_STD_NO_ACTION DOMAIN-6-MC_POLICY_DOWNLOAD 6-Information Master Controller policy downloaded: site_id=[inet] domain=[chars] vrf=[chars] Master Controller policy downloaded. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-MC_POLICY_DOWNLOAD 6-Information Master Controller policy downloaded: site_id=[inet] domain=[chars] vrf=[chars] Master Controller policy downloaded. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-MC_TC_ID_RESET 6-Information Master Controller traffic class id counter got reset: site_id=[inet] domain=[chars] vrf=[chars] Master Controller traffic class id counter got reset. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-MC_TC_ID_RESET 6-Information Master Controller traffic class id counter got reset: site_id=[inet] domain=[chars] vrf=[chars] Master Controller traffic class id counter got reset. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-TC_CTRL 6-Information Traffic Class Controlled. Details: [chars]\n A Traffic Class is Controlled. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-TC_CTRL 6-Information Traffic Class Controlled. Details: [chars]\n A Traffic Class is Controlled. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-TC_NEW 6-Information Traffic Class Learned. Details: [chars]\n A Traffic Class is Learned. ng-pfr LOG_STD_NO_ACTION DOMAIN-6-TC_NEW 6-Information Traffic Class Learned. Details: [chars]\n A Traffic Class is Learned. ng-pfr LOG_STD_NO_ACTION DOSFS-3-RESETERR 3-Error [chars] [chars] disk could not be reset while the system is initiated reload. This will cause a transient disk error disk timeout error when the ROMMON initialization code tries to reads the DIB. This is a transient error and the system will be able to access the disk and continue normal operation. - LOG_STD_NO_ACTION DOSFS-4-DFS_FSCK_ERR 4-Warning Error while running fsck on the file [chars]. Fsck is running in a loop while walking through the cluster chain of a file and has aborted. ata-filesystem LOG_STD_DDTS_TAC_DETAILS DOSFS-5-DFS_CLOSE_ERR 5-Notice Error during close of the file [chars]. [chars] An error occured during a file close operation. - "Enter the fsck filesystem prefix: " "command to check and attempt to repair the disk. If this does not " "fix the problem format the disk." DOSFS-5-DIBERR 5-Notice [chars] [chars] The system cannot boot a image from the Flash disk because the Device Information Block is different. The Flash disk can be read by the router but will require formatting by the router before an image can be booted from it. - "Follow any instructions provided in the error " "message. Before storing a image in the Flash disk " "and trying to boot from this device enter the " "format command to format the flash disk from the " "router. Then copy the desired image to the Flash " "disk and then boot from this device." DOT1AD-4-DOT1QTUNNEL_PORT 4-Warning Port [chars] is a dot1q-tunnel port it conflicts with Dot1ad configuration Dot1ad configuration cannot co-exist with dot1q-tunnel ports. dot1ad "Turn off dot1q-tunnel configuration on the ports before enabling Dot1ad." DOT1AD-4-DOT1X_PORT 4-Warning Port [chars] is configured for DOT1X it conflicts with Dot1ad configuration Dot1ad configuration cannot co-exist with DOT1X enabled ports. dot1ad "Turn off DOT1X configuration on the ports before enabling Dot1ad." DOT1AD-4-ETHERTYPEMISMATCH_PORT 4-Warning Port [chars] ethertype cannot be changed to Dot1ad ethertype it conflicts with Dot1ad configuration The ethertype on the port cannot be changed to Dot1ad ethertype. dot1ad "Replace the module with one which can support ethertype change or " "power down the module before enabling Dot1ad." DOT1AD-4-L2PT_PORT 4-Warning Port [chars] is a l2protocol-tunnel port it conflicts with Dot1ad configuration Dot1ad configuration cannot co-exist with l2protocol-tunnel ports. dot1ad "Turn off l2protocol-tunnel configuration on the ports before enabling " "Dot1ad." DOT1AD-4-LACP_PORT 4-Warning Port [chars] is a part of an LACP channel it conflicts with Dot1ad configuration Dot1ad configuration cannot co-exist with LACP ports. dot1ad "Turn off LACP configuration on the ports before enabling Dot1ad." DOT1AD-4-OAM_PORT 4-Warning Port [chars] is configured for OAM it conflicts with Dot1ad configuration Dot1ad configuration cannot co-exist with OAM enabled ports. dot1ad "Turn off OAM configuration on the ports before enabling Dot1ad." DOT1AD-4-PLATFORM_RESOURCE_UNAVAILABLE 4-Warning Platform does not have resouces to support dot1ad configuration In the 6500 platform hardware match registers are not available for dot1ad use. dot1ad "Unconfigure the features using the match registers cfm cgvrp and " DOT1AD-4-STP_CONFLICT 4-Warning STP mode conflicts with Dot1ad configuration as it is not in MST mode Current STP mode conflicts with Dot1ad configuration. dot1ad "Change the STP mode to MST before enabling Dot1ad." DOT1Q_TUNNELLING-4-MTU_WARNING 4-Warning \nSystem MTU of [dec] might be insufficient for 802.1Q tunnelling.\n 802.1Q tunnelling requires system MTU size of [dec] to handle maximum size ethernet frames.\n\n With 802.1Q tunnelling the system MTU setting needs to take into account the four byte overhead associated with the additional 802.1Q tag. firmware "Issue the system mtu " "global configuration command to adjust system MTU to take into " "account the additional 802.1Q tag." DOT1X_MOD-3-NULLPTR 3-Error Unexpected null pointer in [chars] at [dec] An internal software error occurred. - LOG_STD_SH_TECH_ACTION DOT1X_SWITCH-4-PROC_START_ERR 4-Warning Unable to start dot1x switch process. The system failed to create the Dot1x switch process. - "Reload the device" DOT1X_SWITCH-5-ERR_ADDING_ADDRESS 5-Notice Unable to add address [enet] on [chars] AuditSessionID [chars] The authenticated host's address could not be added. This is likely because either the TCAM is full or the address exists as a secure address on another port. - "If the TCAM is full clear some dynamic addresses to make " "room for the host's address. If the host's address is " "secured on another port manually remove it from that port." DOT1X_SWITCH-5-ERR_INVALID_PRIMARY_VLAN 5-Notice Attempt to assign primary VLAN [chars] to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a primary VLAN to an 802.1x port which is not allowed. - "Update the configuration to use a different VLAN." DOT1X_SWITCH-5-ERR_INVALID_SEC_VLAN 5-Notice Attempt to assign invalid secondary VLAN [chars] to PVLAN host 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a non-secondary VLAN to a PVLAN host 802.1x port. - "Change the mode of the port so that it is no longer a PVLAN host " "port or use a valid secondary VLAN." DOT1X_SWITCH-5-ERR_PRIMARY_VLAN_NOT_FOUND 5-Notice Attempt to assign VLAN [chars] whose primary VLAN does not exist or is shutdown to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a private VLAN whose primary VLAN does not exist or is shutdown. - "Make sure the primary VLAN exists and is not shutdown. Also verify that " "the private VLAN is associated with a primary VLAN." DOT1X_SWITCH-5-ERR_SEC_VLAN_INVALID 5-Notice Attempt to assign secondary VLAN [chars] to non-PVLAN host 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a secondary VLAN to a port that is not a PVLAN host port which is not allowed. - "Change the mode of the port so that it is configured as a PVLAN host " "port or use a different VLAN that is not configured as a secondary " "VLAN." DOT1X_SWITCH-5-ERR_SPAN_DST_PORT 5-Notice Attempt to assign VLAN [chars] to 802.1x port [chars] which is configured as a SPAN destination AuditSessionID [chars] An attempt was made to assign a VLAN to an 802.1x port which is configured as a SPAN destination port - "Change the SPAN configuration so that the port is no longer a " "SPAN destination port or change the configuration so that no " "VLAN is assigned." DOT1X_SWITCH-5-ERR_VLAN_EQ_MDA_INACTIVE 5-Notice Multi-Domain Authentication cannot activate because Data and Voice VLANs are the same on port AuditSessionID [chars] Multi-Domain Authentication host mode cannot activate if the configured Data VLAN on a port is the same as Voice VLAN. - "Change either the Voice VLAN or the access VLAN on " "the interface so they are not equal anymore. This will cause " "Multi-Domain authentication to activate." DOT1X_SWITCH-5-ERR_VLAN_EQ_VVLAN 5-Notice Data VLAN [chars] on port [chars] cannot be equivalent to the Voice VLAN AuditSessionID [chars] An attempt was made to assign a data VLAN to an 802.1x port that is the same as the voice VLAN. - "Change either the Voice VLAN or the access/802.1x assigned VLAN on " "the interface so they are not equal anymore. This will cause the " "authentication to proceed normally on the next retry." DOT1X_SWITCH-5-ERR_VLAN_INTERNAL 5-Notice Attempt to assign internal VLAN [chars] to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is used internally and cannot be assigned to this port. - "Update the configuration not to use this VLAN." DOT1X_SWITCH-5-ERR_VLAN_INVALID 5-Notice Attempt to assign invalid VLAN [chars] to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is out of range and cannot be assigned to this port. - "Update the configuration to use a valid VLAN." DOT1X_SWITCH-5-ERR_VLAN_NOT_FOUND 5-Notice Attempt to assign non-existent or shutdown VLAN [chars] to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a VLAN to an 802.1x port but the VLAN was not found in the VTP database. - "Make sure the VLAN exists and is not shutdown or use another VLAN." DOT1X_SWITCH-5-ERR_VLAN_ON_ROUTED_PORT 5-Notice Attempt to assign VLAN [chars] to routed 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a VLAN to a routed 802.1x port which is not allowed. - "Change the mode of the port so that it is no longer a routed port " "or change the configuration so that no VLAN is assigned." DOT1X_SWITCH-5-ERR_VLAN_PROMISC_PORT 5-Notice Attempt to assign VLAN [chars] to promiscuous 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign a VLAN to a promiscuous 802.1x port which is not allowed. - "Change the mode of the port so that it is no longer a promiscuous port " "or change the configuration so that no VLAN is assigned." DOT1X_SWITCH-5-ERR_VLAN_RESERVED 5-Notice Attempt to assign reserved VLAN [chars] to 802.1x port [chars] AuditSessionID [chars] An attempt was made to assign an invalid VLAN to an 802.1x port. The VLAN specified is a reserved VLAN and cannot be assigned to this port. - "Update the configuration not to use this VLAN." DOT1X_SWITCH-5-ERR_VLAN_RSPAN 5-Notice Attempt to assign RSPAN VLAN [chars] to 802.1x port [chars]. 802.1x is incompatible with RSPAN AuditSessionID [chars] An attempt was made to assign a Remote SPAN VLAN to an 802.1x port. Remote SPAN should not be enabled on a VLAN in which ports are configured with 802.1x enabled. - "Either disable Remote SPAN configuration on the VLAN OR disable " "802.1x on all the ports in this VLAN." DOT1X-4-MEM_UNAVAIL 4-Warning Memory was not available to perform the 802.1X action. AuditSessionID [chars] Insufficient system memory is available to perform the Dot1x Authentication. - "Reduce other system activity to ease memory " "demands. If conditions warrant upgrade to " "a larger memory configuration." DOT1X-4-MEM_UNAVAIL 4-Warning Memory was not available to perform the 802.1X action. AuditSessionID [chars] Insufficient system memory is available to perform the Dot1x Authentication. - "Reduce other system activity to ease memory " "demands. If conditions warrant upgrade to " "a larger memory configuration." DOT1X-4-PROC_START_ERR 4-Warning Dot1x unable to start. The system failed to create the Dot1x process. - "Restart Dot1x process by entering dot1x " "system-auth-control command. If this message " "recurs Reload the device." DOT1X-4-PROC_START_ERR 4-Warning Dot1x unable to start. The system failed to create the Dot1x process. - "Restart Dot1x process by entering dot1x " "system-auth-control command. If this message " "recurs Reload the device." DOT1X-4-UNKN_ERR 4-Warning An unknown operational error occurred. The Dot1x process cannot operate due to an internal system error. - "Reload the device" DOT1X-4-UNKN_ERR 4-Warning An unknown operational error occurred. The Dot1x process cannot operate due to an internal system error. - "Reload the device" DOT1X-5-FAIL 5-Notice Authentication failed for client [chars] on Interface [chars] Authentication was unsuccessful. - LOG_STD_NO_ACTION DOT1X-5-FAIL 5-Notice Authentication failed for client [chars] on Interface [chars] Authentication was unsuccessful. - LOG_STD_NO_ACTION DOT1X-5-IGNORE_LARGER_EAPOL 5-Notice EAPOL packet size[dec] to be sent is larger than MTU Targetted EAPOL packet size is larger than mtu size of the port on which client is connected and hence ignoring the packet to be sent out 802.1x "Configure AAA server to fragement eap-method" " data so that EAPOL size is smaller than interface MTU size" DOT1X-5-IGNORE_LARGER_EAPOL 5-Notice EAPOL packet size[dec] to be sent is larger than MTU Targetted EAPOL packet size is larger than mtu size of the port on which client is connected and hence ignoring the packet to be sent out 802.1x "Configure AAA server to fragement eap-method" " data so that EAPOL size is smaller than interface MTU size" DOT1X-5-RESULT_OVERRIDE 5-Notice Authentication result overridden for client [chars] on Interface [chars] Authentication result was overridden - LOG_STD_NO_ACTION DOT1X-5-RESULT_OVERRIDE 5-Notice Authentication result overridden for client [chars] on Interface [chars] Authentication result was overridden - LOG_STD_NO_ACTION DOT1X-5-SUCCESS 5-Notice Authentication successful for client [chars] on Interface [chars] Authentication was successful. - LOG_STD_NO_ACTION DOT1X-5-SUCCESS 5-Notice Authentication successful for client [chars] on Interface [chars] Authentication was successful. - LOG_STD_NO_ACTION DOT1X-6-INFO_EAPOL_PING_RESPONSE 6-Information The interface [chars] has an 802.1x capable client with MAC [enet] An EAPOL ping was sent out on this port to determine 802.1x readiness of the client attached. An EAPOL response has been received by the device such as a PC. 802.1x "No action required." DOT1X-6-INFO_EAPOL_PING_RESPONSE 6-Information The interface [chars] has an 802.1x capable client with MAC [enet] An EAPOL ping was sent out on this port to determine 802.1x readiness of the client attached. An EAPOL response has been received by the device such as a PC. 802.1x "No action required." DPP_SYSLOG-3-EVENT_ERR 3-Error Pipeline event - [chars] [chars] Output to syslog from pipeline - "" DPP_SYSLOG-4-EVENT_WARNING 4-Warning Pipeline event - [chars] [chars] Output to syslog from pipeline - "" DPP_SYSLOG-6-EVENT_INFO 6-Information Pipeline event - [chars] [chars] Output to syslog from pipeline - "" DPSS-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the DPSS feature failed. This will cause the feature to not function. qfp-dpss "This is normally a software issue. " "The consequences are that the DPSS feature will not function. " LOG_STD_ACTION DPSS-3-DPSS_INIT_FAILED 3-Error DPSS [chars] Register failed DPSS Initialization of registration failed. cpp-ucode LOG_STD_ACTION DPSS-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper DPSS software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-dpss "This is normally a software issue. " LOG_STD_RECUR_ACTION DPSS-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper DPSS software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-dpss "This is normally a software issue. " LOG_STD_RECUR_ACTION DPSS-3-MEM_INIT_FAILED 3-Error Allocation of [chars] memory failed for DPSS DPSS Initialization of channel pool failed. cpp-ucode LOG_STD_ACTION DPSS-3-PKT_REPLICA_INIT_FAILED 3-Error Register to Generic Packet Replication failed for DPSS DPSS Initialization of packet replication registration failed. cpp-ucode LOG_STD_ACTION DRIP-3-DRIPFAIL 3-Error DRIP: Assertion failed: [chars] An internal software error has occurred. - LOG_STD_ACTION DRIP-6-DRIP_CONFLICT 6-Information DRIP conflict with CRF [dec]. A DRIP conflict has occured. The virtual ring or pseudo ring's\n\ CRF is being re-used in the network. - "Make sure that the CRF vlanid of the virtual ring and the \n\ pseudo ring is unique in the network." DRMI-3-IPC_ERROR 3-Error [chars][chars] [hec] rc:[chars] ERM Framework is experiencing errors when communicating to Line Cards using IPC rmi "show ipc ports" DRMI-3-ISSU_ERR 3-Error [chars] error:[dec] ERM Framework is experiencing ISSU Errors rmi "show ipc ports" DRMI-3-ISSU_MTU 3-Error Client id:[dec] MTU failed error:[dec] ERM Framework is experiencing Errors when performing ISSU GET MTU during a transmit operation rmi "show issu nego" DRMI-3-ISSU_RCV 3-Error Client id:[dec] receive failed error:[dec] ERM Framework is experiencing Errors when performing ISSU Transformation during a receive operation rmi "show ipc ports" DRMI-3-ISSU_XMIT 3-Error Client id:[dec] xmit failed error:[dec] ERM Framework is experiencing Errors when performing ISSU Transformation during a transmit operation rmi "show ipc ports" DROP-3-DOUBLE_DROP 3-Error First drop error cause [dec] update stat cause [dec] trace: [hec] [hec] The drop infrastructure was called for a packet that was previously dropped. cpp-ucode LOG_STD_ACTION DROP-3-RESERVED 3-Error [chars] An invalid drop cause was passed to the drop infrastructure. cpp-ucode LOG_STD_ACTION DRP-3-MULTICOMMAND 3-Error multiple DRP commands encountered Multiple DRP commands were found in a single DRP packet. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DRP-3-NOSOCKET 3-Error Unable to open socket The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." DRP-3-NOWRITE 3-Error unable to send response to [inet]:[dec] A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DRP-3-SUBNETTED 3-Error unable to determine metric for [inet] [inet] subnetted A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DRP-7-NOROUTE 7-Debug no route for destination [inet] A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DS_MODEM-3-BADCB 3-Error Unexpected DSIP data callback for modem An unexpected software event occurred. - LOG_STD_ACTION DS_MODEM-3-FLOW_CONTROL 3-Error DS-RS flow control has got out of sync connection has too many particles free.\n\ slot:[dec] ttynum:[dec] parts_avail:[dec] Indicates the flow control accounting on the DS has got out of sync.\n\ - LOG_STD_ACTION DS_MODEM-3-NORXPAK 3-Error Static receive paktype unavailable Temporarily unable to allocate particle for sending traffic to\n\ modem module indicates a break down of flow control between RS-DS. - LOG_STD_ACTION DS_PHY-2-UPX_SPI_ERR 2-Critical [chars] - - - DS_PHY-3-RM_JIB_IF_ERROR 3-Error Remora hw reset failure - [chars] Cannot hw reset DS PHY ubr10k-sw "Copy the error message exactly as it appears and report it to your " "technical support" DS_PHY-3-UPX_UPGRADE_ERROR 3-Error check/upgrade failure - [chars] upconverter - can't check version or upgrade ubr10k-sw "check type of upconverter" DS_TDM-3-ASSERT_FAIL 3-Error Slot [dec]: Assertion failed: file `[chars]' line [dec] An internal sanity check failed. - "" DS_TDM-3-BAD_CONN 3-Error Slot [dec]: unrecognized TDM connect message received [dec] on An unrecognized TDM connect message was received. - "" DS_TDM-3-BAD_DISCONN 3-Error Slot [dec]: unrecognized TDM disconnect message received [dec] on An unrecognized TDM disconnect message was received. - "" DS_TDM-3-BAD_DSIP 3-Error Slot [dec]: unrecognized DSIP message received [dec] on [chars] feature board An unrecognized DSIP message was received. - "" DS_TDM-3-BAD_MAPPING 3-Error Slot [dec]: Legacy FB [chars] with static port-to-DS0 mapping A software error lead to dynamic port-to-DS0 mapping info being passed to a statically-mapped FB. - "" DS_TDM-3-BAD_S4_POWER_UP 3-Error Slot [dec]: [chars] powered-up with one or more incorrect default settings [chars] - - "" DS_TDM-3-CONV_CLOSE 3-Error Slot [dec]: open MT8986 addr: 0x[hec] connection failed - STo[dec] CHo[dec] An attempt to disable a rate converted connection failed. - "" DS_TDM-3-CONV_OPEN 3-Error Slot [dec]: open MT8986 addr: 0x[hec] [chars] connection failed - An attempt to establish a rate converted connection failed. - "" DS_TDM-3-DISC_FOR_NO_CONN 3-Error Slot [dec]: got disc msg for non-existent conn: [chars]-st%02u-ts%03u/gts>%04u><%04u%04u><%04u is put into conflict state because of errors classifier is already applied but we cannot update the classifier with changed destination IP address or source IP address because of errors. So we put the classifier into conflict state. cmts-application LOG_STD_NO_ACTION DSG-5-CFR_CONFLICT 5-Notice classifier <[chars]> is put into conflict state because of errors classifier is already applied but we cannot update the classifier with changed destination IP address or source IP address because of errors. So we put the classifier into conflict state. cmts-application LOG_STD_NO_ACTION DSG-5-CFR_NOT_APPLIED 5-Notice classifier <[chars]> cannot be applied because of errors classifier cannot be applied because of errors. cmts-application LOG_STD_NO_ACTION DSG-5-CFR_NOT_APPLIED 5-Notice classifier <[chars]> cannot be applied because of errors classifier cannot be applied because of errors. cmts-application LOG_STD_NO_ACTION DSG-5-CFRRMTUNNEL 5-Notice cfr [dec] becomes unresolved it will be removed from the tunnel it belongs to cfr becomes unresolved it will be removed from the tunnel it belongs to cmts-application LOG_STD_NO_ACTION DSG-5-CFRRMTUNNEL 5-Notice cfr [dec] becomes unresolved it will be removed from the tunnel it belongs to cfr becomes unresolved it will be removed from the tunnel it belongs to cmts-application LOG_STD_NO_ACTION DSG-5-DSG_INFO_DB_LOOKUP_FAILURE 5-Notice Faild to find the entry from the DSG Info DB for [chars] [chars] [chars] DSG Info DB lookup failure cmts-application LOG_STD_NO_ACTION DSG-5-DSG_INFO_DB_LOOKUP_FAILURE 5-Notice Faild to find the entry from the DSG Info DB for [chars] [chars] [chars] DSG Info DB lookup failure cmts-application LOG_STD_DDTS_TAC_DETAILS DSG-5-IDENTICAL_CFR 5-Notice cfr [dec] and [dec] are identical two cfrs are identical cmts-application LOG_STD_NO_ACTION DSG-5-IDENTICAL_CFR 5-Notice cfr [dec] and [dec] are identical two cfrs are identical cmts-application LOG_STD_NO_ACTION DSG-5-ILLEGAL_MCASTADDR 5-Notice IP address <[inet]> is not a multicast address or is a reserved multicast address IP address is not an multicast address or is a reserved multicast address cmts-application LOG_STD_NO_ACTION DSG-5-ILLEGAL_MCASTADDR 5-Notice IP address <[inet]> is not a multicast address or is a reserved multicast address IP address is not an multicast address or is a reserved multicast address cmts-application LOG_STD_NO_ACTION DSG-5-ILLEGAL_SOURCEADDR 5-Notice IP address <[inet]> is an illegal source address IP address is an illegal source address cmts-application LOG_STD_NO_ACTION DSG-5-ILLEGAL_SOURCEADDR 5-Notice IP address <[inet]> is an illegal source address IP address is an illegal source address cmts-application LOG_STD_NO_ACTION DSG-5-MAC_ADDR 5-Notice cfr [dec] and cfr [dec] have the same destination IP address [inet] but different MAC addresses [enet] and [enet] two cfrs have the same destination IP address but different MAC addresses cmts-application LOG_STD_NO_ACTION DSG-5-MAC_ADDR 5-Notice cfr [dec] and cfr [dec] have the same destination IP address [inet] but different MAC addresses [enet] and [enet] two cfrs have the same destination IP address but different MAC addresses cmts-application LOG_STD_NO_ACTION DSG-5-NAME_CHANGED 5-Notice hostname <[chars]> is changed from <[inet]> to <[inet]> IP address of a hostname is changed. cmts-application LOG_STD_NO_ACTION DSG-5-NAME_CHANGED 5-Notice hostname <[chars]> is changed from <[inet]> to <[inet]> IP address of a hostname is changed. cmts-application LOG_STD_NO_ACTION DSG-5-NAME_UNRESOLVED 5-Notice hostname <[chars]> cannot be resolved DNS query for a hostname is not successful. cmts-application LOG_STD_NO_ACTION DSG-5-NAME_UNRESOLVED 5-Notice hostname <[chars]> cannot be resolved DNS query for a hostname is not successful. cmts-application LOG_STD_NO_ACTION DSG-5-SEMAPHORE_ERROR 5-Notice failed to obtain the DSG semaphore failed to get the semaphore cmts-application LOG_STD_NO_ACTION DSG-5-SEMAPHORE_ERROR 5-Notice failed to obtain the DSG semaphore failed to get the semaphore cmts-application LOG_STD_NO_ACTION DSG-5-SOURCE_LEN 5-Notice cfr [dec]: source IP address [inet] and source prefix length [dec] don't match source IP address and source prefix length of the cfr don't match cmts-application LOG_STD_NO_ACTION DSG-5-SOURCE_LEN 5-Notice cfr [dec]: source IP address [inet] and source prefix length [dec] don't match source IP address and source prefix length of the cfr don't match cmts-application LOG_STD_NO_ACTION DSG-5-SSM_SOURCE_PREFIX 5-Notice destination IP address is <[inet]> in SSM range source IP address prefix length must be [dec] dest-ip is in SSM range src-ip prefix length should match cmts-application LOG_STD_NO_ACTION DSG-5-SSM_SOURCE_PREFIX 5-Notice destination IP address is <[inet]> in SSM range source IP address prefix length must be [dec] dest-ip is in SSM range src-ip prefix length should match cmts-application LOG_STD_NO_ACTION DSG-5-SSM_SOURCE_ZERO 5-Notice destination IP address is <[inet]> in SSM range source IP address cannot be zero dest-ip is in SSM range src-ip cannot be zero cmts-application LOG_STD_NO_ACTION DSG-5-SSM_SOURCE_ZERO 5-Notice destination IP address is <[inet]> in SSM range source IP address cannot be zero dest-ip is in SSM range src-ip cannot be zero cmts-application LOG_STD_NO_ACTION DSG-5-STATICJOINERR 5-Notice cfr [dec] cannot be enabled because there already exists a non-DSG static join for S [inet] or * [inet] in interface [chars] cfr cannot be enabled because there already exists a non-DSG static join for the multicast group cmts-application LOG_STD_NO_ACTION DSG-5-STATICJOINERR 5-Notice cfr [dec] cannot be enabled because there already has been a non-DSG static join for S [inet] or * [inet] in interface [chars] cfr cannot be enabled because there already exists a non-DSG static join for the multicast group cmts-application LOG_STD_NO_ACTION DSG-6-CFR_APPLIED 6-Information classifier <[chars]> is applied successfully classifier is applied successfully. cmts-application LOG_STD_NO_ACTION DSG-6-CFR_APPLIED 6-Information classifier <[chars]> is applied successfully classifier is applied successfully. cmts-application LOG_STD_NO_ACTION DSG-6-CFR_UPDATED 6-Information classifier <[chars]> is updated classifier is updated cmts-application LOG_STD_NO_ACTION DSG-6-CFR_UPDATED 6-Information classifier <[chars]> is updated classifier is updated cmts-application LOG_STD_NO_ACTION DSG-6-LIST_ERR 6-Information [chars] [dec] Infomational only ubr7200 LOG_STD_NO_ACTION DSG-6-LIST_ERR 6-Information [chars] [dec] Infomational only ubr7200 LOG_STD_NO_ACTION DSG-6-NAME_RESOLVED 6-Information hostname <[chars]> is resolved as <[inet]> DNS query for a hostname is successful. cmts-application LOG_STD_NO_ACTION DSG-6-NAME_RESOLVED 6-Information hostname <[chars]> is resolved as <[inet]> DNS query for a hostname is successful. cmts-application LOG_STD_NO_ACTION DSG-6-NO_TG 6-Information tg <[dec]> removal will remove all tg \conf on bundle and mac-domain. remove global tg is successful. cmts-application LOG_STD_NO_ACTION DSIP-3-CLIENT_ADD_FAIL 3-Error Adding client [dec] after DSIP has started. - - "" DSIP-3-CLIENT_VERSION_MISMATCH 3-Error Some clients on this feature board are running versions which are incompatible with RS. Not initializing any DSIP clients. You can find the incompatible clients by executing the show dsip version command - - "" DSIP-3-CLIVERSDBASE_MALLOC_FAILURE 3-Error Failed to get memory for the DSIP clicnets version database \n\ - "" DSIP-3-GET_INTRAPI_BUF_FAILURE 3-Error Failed to get interrupt api buffers \n\ - "" DSIP-3-GET_VERSBUF_FAILURE 3-Error Failed to get version buffers \n\ - "" DSIP-3-GETPAK 3-Error Failed to get packet buffer \n\ - "" DSIP-3-INCOMPATIBLE_CLIENT 3-Error Incompatible client [chars] on DS slot [dec] with major version [dec] and minor version [dec]. Shutting down all the DSIP clients on this slot - - "" DSIP-3-INTRAPI_BUF_MALLOC_FAILURE 3-Error Failed to get memory for the DSIP interrupt api buffers \n\ - "" DSIP-3-IPC_CLIENT 3-Error IPC subsystem API error[chars] [chars] [dec] - - "" DSIP-3-IPC_PORT 3-Error IPC subsystem API error[chars] [chars] [chars] - - "" DSIP-3-IPC_SEAT 3-Error IPC subsystem API error can not create seat by \n\ the seatid [dec] for the slot [dec] Nitro Interconnect Protocol reliable stack \n\ has failed to create seat for the specified slot. - "" DSIP-3-NO_MAJOR_VERSION 3-Error Client addition to DSIP has failed [chars] [dec] - - "" DSIP-3-PRIVPOOL 3-Error Failed to create DSIP private buffer pool \n\ - "" DSIP-3-RANGE 3-Error DSIP parameter range error [chars] [dec] - - "" DSIP-3-TXCONTEXT 3-Error [chars] slot [dec] client [dec] \n\ - "" DSIP-3-TXCONTEXT_ACTIVE_USE 3-Error Waiting for the active transmit contexts to become inactive \n\ - "" DSIP-3-VERSBUF_MALLOC_FAILURE 3-Error Failed to get memory for the DSIP version buffers \n\ - "" DSIP-3-VERSDBASE_MALLOC_FAILURE 3-Error Failed to get memory for the DSIP version database \n\ - "" DSIPPF-3-BASE_FTBL_MALLOC_FAIL 3-Error Failed to allocate memory for the base fucntion table - - "" DSIPPF-3-DSIP_SEND_FAILURE 3-Error Failed to send DSIP message - number of failures [dec] This message indicates that Nitro Interconnect Protocol\n\ has encountered an error while sending a message and that the\n\ message has been discarded after three unsuccessful resends. - "" DSIPPF-5-DS_HELLO 5-Notice DSIP Hello from shelf [dec] slot [dec] Succeeded - - "" DSIPPF-5-DS_KEEPALIVE_LOSS 5-Notice DSIP Keepalive Loss from shelf [dec] slot [dec] - - "" DSIPPF-5-HELLO_ERROR 5-Notice DSIP Hello from shelf [dec] slot [dec] failed due to DSIP version mismatch - - "" DSIPPF-5-RS_HELLO 5-Notice DSIP Hello from router shelf [dec] Succeeded - - "" DSIPPF-5-RS_KEEPALIVE_LOSS 5-Notice DSIP Keepalive Loss from router shelf [dec] - - "" DSM-3-DSP_TIMEOUT 3-Error DSP timeout on channel [chars] event 0x[hec]: DSP ID=0x[hec]: [chars] Timeout on DSP response. ios-voice "The DSP has been automatically reset. If problem persists contact" "your technical support representative" DSM-3-DSP_TIMEOUT 3-Error DSP timeout on channel [chars] event 0x[hec]: DSP ID=0x[hec]: [chars] Timeout on DSP response. ios-voice "The DSP has been automatically reset. If problem persists contact" "your technical support representative" DSM-3-DSPALARM 3-Error channel [chars] DSP ID 0x[hec]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted. ios-voice "Contact your technical support\n\ representative include the full text of the error message." DSM-3-DSPALARM 3-Error channel [chars] DSP ID 0x[hec]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted. ios-voice "Contact your technical support\n\ representative include the full text of the error message." DSM-3-INTERNAL 3-Error Internal Error : [chars] DSM Internal error ios-voice "Contact your technical support representative" DSM-3-INTERNAL 3-Error Internal Error : [chars] DSM Internal error ios-voice "Contact your technical support representative" DSM-3-MSGSNDFAIL 3-Error channel:[chars] DSP ID:0x[hec] Message ID:0x[hec] A message could not be sent to the DSP. The session continued but may have experienced problems. ios-voice "Contact your technical " "support representative include the full text of the error message." DSM-3-MSGSNDFAIL 3-Error channel:[chars] DSP ID:0x[hec] Message ID:0x[hec] A message could not be sent to the DSP. The session continued but may have experienced problems. ios-voice "Contact your technical " "support representative include the full text of the error message." DSM-3-NOEVENT 3-Error no free event structure available from [chars] for DSM message There were no event structures remaining in the system pools to alert the router of a voice or signaling event. ios-voice "Contact your technical support " "representative include the full text of the error message." DSM-3-NOEVENT 3-Error no free event structure available from [chars] for DSM message There were no event structures remaining in the system pools to alert the router of a voice or signaling event. ios-voice "Contact your technical support " "representative include the full text of the error message." DSM-6-SESSION_DATABASE_FAILED 6-Information Cannot create DSM session database\n Failed to create DSM session. ios-voice "Check the size of free memory to make sure there is enough memory." DSM-6-SESSION_DATABASE_FAILED 6-Information Cannot create DSM session database\n Failed to create DSM session. ios-voice "Check the size of free memory to make sure there is enough memory." DSMIB-3-CLIENT_TYPE 3-Error Type [dec] is invalid for collision [chars] The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error. dsmib "LOG_STD_ACTION" DSMIB-3-CLIENT_TYPE 3-Error Type [dec] is invalid for collision [chars] The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error. dsmib LOG_STD_ACTION DSMIB-3-CLIENT_TYPE 3-Error Type [dec] is invalid for collision [chars] The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error. dsmib "LOG_STD_ACTION" DSMIB-3-CLIENT_TYPE 3-Error Type [dec] is invalid for collision [chars] The specified type of client is an invalid value which indicates that there is no support for the generation of an internal identifier. This is an internal software error. dsmib LOG_STD_ACTION DSMIB-3-RECV_CONF 3-Error Error receiving configuration in DSMIB. The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib "LOG_STD_ACTION" DSMIB-3-RECV_CONF 3-Error Error receiving configuration in DSMIB. The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib LOG_STD_ACTION DSMIB-3-RECV_CONF 3-Error Error receiving configuration in DSMIB. The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib "LOG_STD_ACTION" DSMIB-3-RECV_CONF 3-Error Error receiving configuration in DSMIB. The configuration is not received properly from shim. This indicates that the operation to receive the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib LOG_STD_ACTION DSMIB-3-RECV_STAT 3-Error Error in decoding statistics in DSMIB. The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-RECV_STAT 3-Error Error in decoding statistics in DSMIB. The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIB-3-RECV_STAT 3-Error Error in decoding statistics in DSMIB. The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-RECV_STAT 3-Error Error in decoding statistics in DSMIB. The counters are not received properly from shim. This indicates that the operation to receive the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIB-3-TIMER_START 3-Error [chars] This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-TIMER_START 3-Error [chars] This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIB-3-TIMER_START 3-Error [chars] This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-TIMER_START 3-Error [chars] This indicates that the operation to start/restart a timer has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIB-3-UID_DELETE 3-Error [chars] unable to remove index %08X The specified entity is unable to removed the specified index. This is an internal software error. dsmib "LOG_STD_ACTION" DSMIB-3-UID_DELETE 3-Error [chars] unable to remove index %08X The specified entity is unable to removed the specified index. This is an internal software error. dsmib LOG_STD_ACTION DSMIB-3-UID_DELETE 3-Error [chars] unable to remove index %08X The specified entity is unable to removed the specified index. This is an internal software error. dsmib "LOG_STD_ACTION" DSMIB-3-UID_DELETE 3-Error [chars] unable to remove index %08X The specified entity is unable to removed the specified index. This is an internal software error. dsmib LOG_STD_ACTION DSMIB-3-UID_EXISTS 3-Error [chars] attempt to add index %08X [chars] The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error. dsmib "LOG_STD_SH_CMD_ACTIONshow dsmib db id" DSMIB-3-UID_EXISTS 3-Error [chars] attempt to add index %08X [chars] The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error. dsmib "show dsmib db id" DSMIB-3-UID_EXISTS 3-Error [chars] attempt to add index %08X [chars] The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error. dsmib "LOG_STD_SH_CMD_ACTIONshow dsmib db id" DSMIB-3-UID_EXISTS 3-Error [chars] attempt to add index %08X [chars] The specified entity is unable to add an entry due to the detection of an existing entry with the same index or name. This is an internal software error. dsmib "show dsmib db id" DSMIB-3-WRED_PARENT 3-Error There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled dsmib "LOG_STD_ACTION" DSMIB-3-WRED_PARENT 3-Error There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled dsmib LOG_STD_ACTION DSMIB-3-WRED_PARENT 3-Error There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled dsmib "LOG_STD_ACTION" DSMIB-3-WRED_PARENT 3-Error There is a child policy under class [chars] in policy-map [chars] where random-detect is configured which is not supported while diffservmib RFC 2475 is enabled Random-detect is not supported in parent class of a HQOS policy when diffservmib RFC 2475 is enabled dsmib LOG_STD_ACTION DSMIB-3-XMIT_CONF 3-Error [chars] The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib LOG_STD_ACTION DSMIB-3-XMIT_CONF 3-Error [chars] The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib LOG_STD_ACTION DSMIB-3-XMIT_MSG 3-Error [chars] The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync. dsmib "LOG_STD_ACTION" DSMIB-3-XMIT_MSG 3-Error [chars] The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync. dsmib LOG_STD_ACTION DSMIB-3-XMIT_MSG 3-Error [chars] The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync. dsmib "LOG_STD_ACTION" DSMIB-3-XMIT_MSG 3-Error [chars] The IPC message was not transmitted. This condition will result in counters out-of-sync between MQC and dsmib or some config being out of sync. dsmib LOG_STD_ACTION DSMIB-3-XMIT_STAT 3-Error Error in statistics query and encoding in DSMIB. The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-XMIT_STAT 3-Error Error in statistics query and encoding in DSMIB. The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIB-3-XMIT_STAT 3-Error Error in statistics query and encoding in DSMIB. The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib "LOG_STD_ACTION" DSMIB-3-XMIT_STAT 3-Error Error in statistics query and encoding in DSMIB. The counters are not encoded and transmitted properly from shim. This indicates that the operation to encode the statistics from shim has failed. This condition will result in counters out-of-sync between MQC and dsmib. dsmib LOG_STD_ACTION DSMIBPROV-3-CLASSNOTFOUND 3-Error class: [chars] is not present in db. This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with class name for any possible debugging. dsmib "LOG_STD_ACTION" DSMIBPROV-3-CLASSNOTFOUND 3-Error class: [chars] is not present in db. This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with class name for any possible debugging. dsmib LOG_STD_ACTION DSMIBPROV-3-CLASSNOTFOUND 3-Error class: [chars] is not present in db. This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with class name for any possible debugging. dsmib "LOG_STD_ACTION" DSMIBPROV-3-CLASSNOTFOUND 3-Error class: [chars] is not present in db. This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the classmap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with class name for any possible debugging. dsmib LOG_STD_ACTION DSMIBPROV-3-POLICYNOTFOUND 3-Error policy: [chars] is not present in db. This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with policy name for any possible debugging. dsmib "LOG_STD_ACTION" DSMIBPROV-3-POLICYNOTFOUND 3-Error policy: [chars] is not present in db. This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with policy name for any possible debugging. dsmib LOG_STD_ACTION DSMIBPROV-3-POLICYNOTFOUND 3-Error policy: [chars] is not present in db. This is a configuration error for dsmib.It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations.Capture the log in the console with policy name for any possible debugging. dsmib "LOG_STD_ACTION" DSMIBPROV-3-POLICYNOTFOUND 3-Error policy: [chars] is not present in db. This is a configuration error for dsmib. It indicates that dsmib shim does not get the notification when the policymap is configured on the box through MQC. This also potentially means the dsmib db will be out-of-sync with respect to MQC configurations. Capture the log in the console with policy name for any possible debugging. dsmib LOG_STD_ACTION DSMIBPROV-3-XMIT_CONF 3-Error [chars] The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib "LOG_STD_ACTION" DSMIBPROV-3-XMIT_CONF 3-Error [chars] The configuration is not transmitted properly from shim. This indicates that the operation to transmit the configurations from shim has failed. This condition will result in out-of-sync information in dsmib with respect to shim. dsmib "LOG_STD_ACTION" DSMIBPROV-6-UNSUPPORTED 6-Information [chars] This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations.Then try with different configurations valid for dsmib. dsmib "LOG_STD_NO_ACTION" DSMIBPROV-6-UNSUPPORTED 6-Information [chars] This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations. Then try with different configurations valid for dsmib. - LOG_STD_NO_ACTION DSMIBPROV-6-UNSUPPORTED 6-Information [chars] This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations.Then try with different configurations valid for dsmib. dsmib "LOG_STD_NO_ACTION" DSMIBPROV-6-UNSUPPORTED 6-Information [chars] This is a provisioning error for dsmib. It indicates that dsmib does not support the configuration entered. See the error message printed out on the console for possible supported configurations. Then try with different configurations valid for dsmib. - LOG_STD_NO_ACTION DSMP-3-DSP_TIMEOUT 3-Error DSP timeout on DSP [chars]: event 0x[hec] [chars] Timeout on DSP response. ios-voice "The DSP has been automatically reset. If problem persists contact" "your technical support representative" DSMP-3-DSP_TIMEOUT 3-Error DSP timeout on DSP [chars]: event 0x[hec] [chars] Timeout on DSP response. ios-voice "The DSP has been automatically reset. If problem persists contact" "your technical support representative" DSMP-3-DSPALARM 3-Error Alarm on DSP [chars]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted. ios-voice "Contact your technical support\n\ representative include the full text of the error message." DSMP-3-DSPALARM 3-Error Alarm on DSP [chars]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All sessions on the DSP were dropped and a DSP reload was attempted. ios-voice "Contact your technical support\n\ representative include the full text of the error message." DSMP-3-INTERNAL 3-Error Internal Error : [chars] DSMP Internal error ios-voice "Contact your technical support representative" DSMP-3-INTERNAL 3-Error Internal Error : [chars] DSMP Internal error ios-voice "Contact your technical support representative" DSMP-3-INVALID_EVENT 3-Error Unhandled event: current state:[chars] event:[chars] The event is not handled in the DSMP gateway state machine specification ios-voice "Contact your technical support representative" DSMP-3-INVALID_EVENT 3-Error Unhandled event: current state:[chars] event:[chars] The event is not handled in the DSMP gateway state machine specification ios-voice "Contact your technical support representative" DSMP-3-MSGSNDFAIL 3-Error channel:[chars] DSP ID:0x[hec] Message ID:0x[hec] A message could not be sent to the DSP. The session continued but may have experienced problems. ios-voice "Contact your technical support \n\ representative include the full text of the error message." DSMP-3-MSGSNDFAIL 3-Error channel:[chars] DSP ID:0x[hec] Message ID:0x[hec] A message could not be sent to the DSP. The session continued but may have experienced problems. ios-voice "Contact your technical support \n\ representative include the full text of the error message." DSMP-3-NOEVENT 3-Error no free event structure available from [chars] for DSMP message There were no event structures remaining in the system pools to alert the router of a voice or signaling event. ios-voice "Contact your technical support " "representative include the full text of the error message." DSMP-3-NOEVENT 3-Error no free event structure available from [chars] for DSMP message There were no event structures remaining in the system pools to alert the router of a voice or signaling event. ios-voice "Contact your technical support " "representative include the full text of the error message." DSMP-3-NOLICENSE 3-Error [chars]:No License available Tivan Recording could not be Triggered There are no recording license remaining in the license pool ios-voice " Check your configuration for smart license availability" DSMP-3-NOLICENSE 3-Error [chars]:No License available Tivan Recording could not be Triggered There are no recording license remaining in the license pool ios-voice " Check your configuration for smart license availability" DSMP-3-PRG_ERROR 3-Error Programming Error : [chars] Progaramming error in DSMP subsys ios-voice "Contact your technical support representative" DSMP-3-PRG_ERROR 3-Error Programming Error : [chars] Progaramming error in DSMP subsys ios-voice "Contact your technical support representative" DSMP-3-SUBSYS_UNINITIALIZED 3-Error Internal Error : [chars] DSMP Subsystem not initialized ios-voice "Contact your technical support representative" DSMP-3-SUBSYS_UNINITIALIZED 3-Error Internal Error : [chars] DSMP Subsystem not initialized ios-voice "Contact your technical support representative" DSMP-4-WARNING 4-Warning Warning : [chars] Resource temporarily not available ios-voice "Contact your technical support representative if condition lasts" DSMP-4-WARNING 4-Warning Warning : [chars] Resource temporarily not available ios-voice "Contact your technical support representative if condition lasts" DSMP-6-SESSION_DATABASE_FAILED 6-Information Cannot create DSMP session database\n Failed to create DSMP session. ios-voice "Check the size of free memory to make sure there is enough memory." DSMP-6-SESSION_DATABASE_FAILED 6-Information Cannot create DSMP session database\n Failed to create DSMP session. ios-voice "Check the size of free memory to make sure there is enough memory." DSP_SPA-2-INITFAIL 2-Critical Not Enough Resources:[chars] The shared port adaptor failed to complete software initialization. SPA-DSP "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DSP_SPA-3-BUFF_FAIL 3-Error Not Enough MEM Buffers [chars] Not enought memory buffers for shared port adaptor operation. SPA-DSP "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DSP_SPA-3-FILE_OP_FAIL 3-Error Failed to open file [chars] : [chars] Failed to open file SPA-DSP "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DSP_SPA-3-FILE_RD_FAIL 3-Error Failed to read [dec] bytes from file: [chars] Failed to read data from file SPA-DSP "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DSP_SPA-3-HW_ERROR 3-Error [chars]: A Hardware device error was detected. Trying to recover the SPA by reload. Error information : [chars] An internal hardware device error has occurred on the services SPA. The error message indicates the slot subslot the SPA type and the name of the hardware device. The SPA has been deactivated and reactivated to resolve the problem. If the error occurs more than five times within an hour no further attempts to reactivate the SPA will be made. This message is likely due to an unrecoverable hardware failure. spa-dsp "Perform OIR of the SPA located in the specified subslot. Before removing " "the SPA enter the hw-module subslot stop command. " "Remove the SPA wait 5 seconds and reinsert the SPA. If " "the problem persists copy the error message text exactly as it appears " "on the console or in the system log enter the show diag" " command contact your Cisco technical support representative " "and provide the representative with the gathered information." DSP_SPA-3-HW_ERROR_INFO 3-Error [chars]: Non fatal hardware device error was detected. Error information : [chars] An internal hardware device error has occurred on the services SPA. The error message indicates the slot subslot the SPA type and the name of the hardware device. This message is likely due to a recoverable hardware failure. spa-dsp "Perform OIR of the SPA located in the specified subslot. Before removing " "the SPA enter the hw-module subslot stop command. " "Remove the SPA wait 5 seconds and reinsert the SPA. If " "the problem persists copy the error message text exactly as it appears " "on the console or in the system log enter the show diag" " command contact your Cisco technical support representative " "and provide the representative with the gathered information." DSP_SPA-3-NULL_FAIL 3-Error Non-Initialized ptr: [chars] About to Access non-initialized pointer SPA-DSP "Copy the error message exactly as it appears and report it to your\n\ technical support representative." DSP-3-DSP_ALARM 3-Error DSP device [dec] is not responding. Trying to recover DSP device by reloading A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device. spa-dsp "Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the hw-module subslot stop command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the show diag command contact " "your Cisco technical support representative and provide the " "representative with the gathered information." DSP-3-DSP_DNLD 3-Error DSP device [dec] DNLD process exited. Trying to recover DSP device by rebooting the DSP A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device. spa-dsp "Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the hw-module subslot stop command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the show diag command contact " "your Cisco technical support representative and provide the " "representative with the gathered information." DSP-3-DSP_KEEPALIVE 3-Error DSP device [dec] is not responding. Trying to recover DSP device by reloading A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device. spa-dsp "Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the hw-module subslot stop command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the show diag command contact " "your Cisco technical support representative and provide the " "representative with the gathered information." DSP-3-DSP_WATCHDOG 3-Error DSP device [dec] is not responding. Trying to recover DSP device by reloading A DSP device on DSP-SPA is not responding. The error message indicates the slot subslot the SPA type and the name of the hardware device. spa-dsp "Software will try to recover by reloading the failed DSP. " "If the problem persists then perform OIR of the SPA located in the " "specified subslot. Before removing the SPA enter " "the hw-module subslot stop command. Remove the SPA " "wait 5 seconds and reinsert the SPA. If the problem persists copy " "the error message text exactly as it appears on the console or in the " "system log enter the show diag command contact " "your Cisco technical support representative and provide the " "representative with the gathered information." DSP-3-FIRMWARE_VER_INFO 3-Error Downloading streamware... for device [dec]. DSP firmwarever:[dec].[dec] contained in image has different version from DSP firmware version check - LOG_STD_NO_ACTION DSP-3-TIMER 3-Error [chars] timer expired for DSP [dec] DSP timer has expired - LOG_STD_NO_ACTION DSP-5-DNLD 5-Notice DNLD started for device [dec] DSP bootloader DNLD starte - LOG_STD_NO_ACTION DSP-5-UPDOWN 5-Notice DSP [dec] is [chars] DSP device changed state up/down - LOG_STD_NO_ACTION DSPDUMP-5-DUMPSTART 5-Notice DSP [dec] 0x[hec] in slot [dec] starting dump The DSP resource is beginning crash dump collection - LOG_STD_NO_ACTION DSPDUMP-5-DUMPSTART 5-Notice DSP [dec] 0x[hec] in slot [dec] starting dump The DSP resource is beginning crash dump collection - LOG_STD_NO_ACTION DSPDUMP-5-RX_CONTROL_DROP 5-Notice DSP [dec] in slot [dec] Rx Control Message Dropped by DSP The DSP has reported that a Rx Control Message was dropped - LOG_STD_NO_ACTION DSPDUMP-5-RX_CONTROL_DROP 5-Notice DSP [dec] in slot [dec] Rx Control Message Dropped by DSP The DSP has reported that a Rx Control Message was dropped - LOG_STD_NO_ACTION DSPDUMP-5-TX_CONTROL_DROP 5-Notice DSP [dec] in slot [dec] Tx Control Message Dropped by DSP The DSP has reported that a Tx Control Message was dropped - LOG_STD_NO_ACTION DSPDUMP-5-TX_CONTROL_DROP 5-Notice DSP [dec] in slot [dec] Tx Control Message Dropped by DSP The DSP has reported that a Tx Control Message was dropped - LOG_STD_NO_ACTION DSPFARM-3-ERROR 3-Error [chars] Error on DSPFARM module. - LOG_STD_SH_TECH_ACTION DSPFARM-3-ERROR 3-Error Errors on DSPFARM module [chars]\n Errors on DSPFARM module dspfarm " Check sh dspfarm all" DSPFARM-3-ERROR 3-Error [chars] Error on DSPFARM module. - LOG_STD_SH_TECH_ACTION DSPFARM-3-ERROR 3-Error Errors on DSPFARM module [chars]\n Errors on DSPFARM module dspfarm " Check sh dspfarm all" DSPFARM-4-INFO 4-Warning Info on DSPFARM module [chars]\n Info on DSPFARM module dspfarm " Check sh dspfarm" DSPFARM-4-INFO 4-Warning Info on DSPFARM module [chars]\n Info on DSPFARM module dspfarm " Check sh dspfarm" DSPFARM-4-NOTICE 4-Warning Failure on DSPFARM module [chars]\n Failure on DSPFARM module dspfarm " Check sh dspfarm" DSPFARM-4-NOTICE 4-Warning Failure on DSPFARM module [chars]\n Failure on DSPFARM module dspfarm " Check sh dspfarm" DSPFARM-4-WARNING 4-Warning Warning on DSPFARM module [chars]\n Warning on DSPFARM module dspfarm " Check sh dspfarm all" DSPFARM-4-WARNING 4-Warning Warning on DSPFARM module [chars]\n Warning on DSPFARM module dspfarm " Check sh dspfarm all" DSPRM-2-DSPALARM 2-Critical Received alarm indication from dsp [dec]/[dec]. Resetting the DSP. Fatal error detected in DSP. voice-dsp "contact your technical support representative." DSPRM-2-DSPALARM 2-Critical Received alarm indication from dsp [dec]/[dec]. Resetting the DSP. Fatal error detected in DSP. voice-dsp "contact your technical support representative." DSPRM-2-FORKFAIL 2-Critical Process creation of [chars] failed. Failed to create the process. c3800 LOG_STD_ACTION DSPRM-2-FORKFAIL 2-Critical Process creation of [chars] failed. Failed to create the process. c3800 LOG_STD_ACTION DSPRM-3-DSPALARMINFO 3-Error [chars] DSP Alarm Data - "" DSPRM-3-DSPALARMINFO 3-Error [chars] DSP Alarm Data - "" DSPRM-3-INSUFFICIENT 3-Error Insufficient DSP resources for timeslot [dec] on port [chars] The configuration requires more DSP resources than are available. - "Change the configuration to specify fewer used timeslots.\n\ Install additional DSP resources to allow more complex\n\ configurations." DSPRM-3-INSUFFICIENT 3-Error Insufficient DSP resources for timeslot [dec] on port [chars] The configuration requires more DSP resources than are available. - "Change the configuration to specify fewer used timeslots.\n\ Install additional DSP resources to allow more complex\n\ configurations." DSPRM-3-INSUFFICIENT_DSP 3-Error \nvoice-port : [chars] Not initialized due to insufficient DSP resources More DSP resources are needed to initialize the analog voice-port - "Install additional DSP resources to allow voice-port initialization" DSPRM-3-INSUFFICIENT_DSP 3-Error \nvoice-port : [chars] Not initialized due to insufficient DSP resources More DSP resources are needed to initialize the analog voice-port - "Install additional DSP resources to allow voice-port initialization" DSPRM-5-DSP_VIC_CONFIG_NAK 5-Notice Received VIC config NAK from DSP[dec]/[dec] resetting the DSP. Receieved NAK message from DSP. Re-attempt initialization. - LOG_STD_NO_ACTION DSPRM-5-DSP_VIC_CONFIG_NAK 5-Notice Received VIC config NAK from DSP[dec]/[dec] resetting the DSP. Receieved NAK message from DSP. Re-attempt initialization. - LOG_STD_NO_ACTION DSPRM-5-DSPFAIL 5-Notice DSP [dec] in slot [chars] is in the failed state The DSP entered the FAILED state due to alarm indications. - "Replace the DSP resource." DSPRM-5-DSPFAIL 5-Notice DSP [dec] in slot [chars] is in the failed state The DSP entered the FAILED state due to alarm indications. - "Replace the DSP resource." DSPRM-5-DSPMSGFAIL 5-Notice Failed to get dsprm msg for msg id [chars] Unable to get dsprm control message - LOG_STD_NO_ACTION DSPRM-5-DSPMSGFAIL 5-Notice Failed to get dsprm msg for msg id [chars] Unable to get dsprm control message - LOG_STD_NO_ACTION DSPRM-5-JUKEBOX 5-Notice Jukebox transmit overlay resp [dec] on slot [chars] failed The Jukebox received failed response code. - "" DSPRM-5-JUKEBOX 5-Notice Jukebox transmit overlay resp [dec] on slot [chars] failed The Jukebox received failed response code. - "" DSPRM-5-JUKEBOX_UPDOWN 5-Notice DSP Jukebox[dec] in slot [chars] changed state to [chars] The DSP JUKEBOX changed state. - LOG_STD_NO_ACTION DSPRM-5-JUKEBOX_UPDOWN 5-Notice DSP Jukebox[dec] in slot [chars] changed state to [chars] The DSP JUKEBOX changed state. - LOG_STD_NO_ACTION DSPRM-5-KEEPALIVE 5-Notice DSP [dec] in slot [chars] NOT RESPONDING - auto restart[dec] times The DSP failed the background keep-alive test. - LOG_STD_NO_ACTION DSPRM-5-KEEPALIVE 5-Notice DSP [dec] in slot [chars] NOT RESPONDING - auto restart[dec] times The DSP failed the background keep-alive test. - LOG_STD_NO_ACTION DSPRM-5-NULLIDB_CREATE_FAIL 5-Notice VoIP Null IDB creation failed. VoIP nullidb creation failed. - "" DSPRM-5-NULLIDB_CREATE_FAIL 5-Notice VoIP Null IDB creation failed. VoIP nullidb creation failed. - "" DSPRM-5-SETCODEC 5-Notice Configured codec [dec] is not supported with this dsp image. Codec negotiation failed. - "" DSPRM-5-SETCODEC 5-Notice Configured codec [dec] is not supported with this dsp image. Codec negotiation failed. - "" DSPRM-5-UP_DOWN 5-Notice DSP [dec] in subslot [chars] changed state to [chars] The DSP resource changed state. - LOG_STD_NO_ACTION DSPRM-5-UP_DOWN 5-Notice DSP [dec] in subslot [chars] changed state to [chars] The DSP resource changed state. - LOG_STD_NO_ACTION DSPRM-5-UPDOWN 5-Notice DSP [dec] in slot [dec] changed state to [chars] The DSP resource changed state. - LOG_STD_NO_ACTION DSPRM-5-UPDOWN 5-Notice DSP [dec] in slot [dec] changed state to [chars] The DSP resource changed state. - LOG_STD_NO_ACTION DSPU-3-ActpuNegResponse 3-Error ACTPU Neg rsp received from PU [chars] Remote PU rejected the router's request for an SSCP-PU session. - "Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the problem exists at the remote PU and correct it.\n\ If the problem persists call your Cisco technical support\n\ representative for assistance." DSPU-3-CLSIBadAdptCorr 3-Error CLSI bad Adaptor correlator header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadIdentifier 3-Error CLSI bad identifier header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadIdentifierType 3-Error CLSI bad identifier type header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadLength 3-Error CLSI bad length header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadPrimitiveCmd 3-Error CLSI bad primitive command header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadPrimitiveType 3-Error CLSI bad primitive type header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIBadReturnCode 3-Error CLSI bad return code: [dec] header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIUnexpctActSapCnf 3-Error CLSI unexpected ActivateSapCnf header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIUnexpctDeactSapCnf 3-Error CLSI unexpected DeactivateSapCnf header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIUnexpctEnableCnf 3-Error CLSI unexpected EnableCnf header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-CLSIUnexpctIdStnInd 3-Error CLSI unexpected IdStnInd header= [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-DSPU_BufferCorrupted 3-Error DSPU could not free buffer - buffer corrupted An internal software error occurred. - LOG_STD_RECUR_ACTION DSPU-3-LSConnInFailed 3-Error Connect in from remote address [chars] failed. Connection with the remote station could not be established because of\n\ insufficient memory in the router. - "Correct low memory problem in the router. If the problem persists\n\ call your technical support representative for assistance." DSPU-3-LSConnInFromHostFailed 3-Error Connect in from host [chars] with remote address [chars] failed. Connection with the remote host could not be established. - "Verify host configuration parameters at the router and at the host.\n\ Determine whether the router is configured to accept connection from\n\ this host." DSPU-3-LSConnInFromPuFailed 3-Error Connect in from pu [chars] with remote address [chars] failed. Connection with the remote PU could not be established. - "Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the router is configured to accept connectIn from\n\ this remote PU." DSPU-3-LSConnOutToHostFailed 3-Error Connect out to host [chars] failed. Connection with the remote host could not be established. - "Verify host configuration parameters at the router and at the host.\n\ Determine whether the host is active and responding to connection\n\ requests." DSPU-3-LSConnOutToPuFailed 3-Error Connect out to pu [chars] failed. Connection with the remote PU could not be established. - "Verify PU configuration parameters at the router and at the remote PU.\n\ Determine whether the remote PU is active and responding to connection\n\ requests." DSPU-3-LSInvalidMaxIFrame 3-Error Connection attempt failed from XID= [chars] Invalid MaxIFrame= [dec] - - "Correct link station configuration at the remote station." DSPU-3-LSInvalidWindowSize 3-Error Connection attempt failed from XID= [chars] Invalid WindowSize= [dec] - - "Correct link station configuration at the remote station." DSPU-3-LSNoACTPUCapability 3-Error Connection attempt failed from XID= [chars] ACTPU not supported - - - DSPU-3-LSXIDNegotiationError 3-Error XID Negotiation Error bad byte= [dec] bad bit= [dec] sense data= [chars] - - "Determine from the CV 22 byte or bit information which field in the\n\ XID3 is rejected by the remote station and correct the link station\n\ configuration parameters at either the router or the remote station." DSPU-3-NotifyNegRsp 3-Error LU [dec] received a Notify Neg Resp from host [chars] Remote host rejected the router's request to activate/deactivate an\n\ SSCP-LU session. - "Verify host configuration parameters at the router and at the remote\n\ host. Determine whether the problem exists at the remote host and\n\ correct it. If the problem persists call your technical support\n\ representative for assistance." DSPU-3-SnaBadData 3-Error Bad SNA data received from PU [chars] data= [chars] Unrecognized SNA data was received from the remote PU. - "Correct the problem at the remote PU. If the problem persists call\n\ your Cisco technical support representative for assistance." DSPU-3-UnknownXid 3-Error XID Format not supported XID= [chars] - - - DSS-3-ACK_FAIL 3-Error Ack failed for dsp_id [dec]\n\ seq_no [dec] DSP core not responding to host messages - LOG_STD_NO_ACTION DSS-3-DSPID_INVALID 3-Error Invalid DSPID [dec] Invalid DSP ID detetced in the message - LOG_STD_NO_ACTION DSS-3-TIMER 3-Error [chars] timer expired for DSPID [dec] DSS timer has expired - LOG_STD_NO_ACTION DSS-5-UPDOWN 5-Notice DSP core [dec] is [chars] DSP core changed state up/down - LOG_STD_NO_ACTION DSX0-5-RBSLINEDBUSYOUT 5-Notice RBS of slot [dec] controller [dec] timeslot [dec] is dynamic busyout - - LOG_STD_NO_ACTION DSX0-5-RBSLINEDOWN 5-Notice RBS of controller [dec] timeslot [dec] is down - - LOG_STD_NO_ACTION DSX0-5-RBSLINESBUSYOUT 5-Notice RBS of slot [dec] controller [dec] timeslot [dec] is static busyout - - LOG_STD_NO_ACTION DSX0-5-RBSLINEUNBUSYOUT 5-Notice RBS of slot [dec] controller [dec] timeslot [dec] is unbusyout - - LOG_STD_NO_ACTION DSX0-5-RBSLINEUP 5-Notice RBS of controller [dec] timeslot [dec] is up - - LOG_STD_NO_ACTION DSX1-1-FIRMWARE_RESTART_FAILED 1-Alert Trunk Firmware in slot [dec] reset failed Trunk could not be restarted. dsx1 LOG_STD_ACTION DSX1-1-FIRMWARE_RUNNING 1-Alert T1/E1 Firmware in slot [dec] is running T1/E1 Firmware is now running after recovering from critical error. dsx1 LOG_STD_ACTION DSX1-1-FIRMWARE_STOPPED 1-Alert T1/E1 Firmware in slot [dec] is not running Critical error occurred in the T1/E1 Firmware and it stopped running. \n\ Access server needs to be reloaded. dsx1 LOG_STD_ACTION DSX1-1-M32_INPUT_CONGEST 1-Alert Munich 32 channel input queue is congested Can't allocate receive buffers since input queue is at its maximum this indicates\n\ data is coming faster than the receiver can handle. dsx1 "Reduce data goes into this channel and or increase the number of input queue." DSX1-3-FIRMWARE_RESTART 3-Error T1/E1 Firmware in slot [dec] restarted T1/E1 Firmware restarted. All the active calls on the T1/E1 lines\n\ will be disconnected and the controllers will come back up within\n\ few seconds dsx1 LOG_STD_ACTION DSX1-3-M32_AR_FAILURE 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_AR_TIMEOUT 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_BAD_BITRATE 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_BAD_INTQ 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_BAD_STATE 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_ERR 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_ILLEGAL_CHANNEL 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_MEM_ALLOC 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_NO_TIMESLOT 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-M32_TIMESLOT_IN_USE 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-3-NOMEMORY 3-Error MSG_TRACEBACK|MSG_PROCESS - - - DSX1-6-CLOCK_CHANGE 6-Information [chars] clock is now selected as clock source - - LOG_STD_NO_ACTION DSX-4-ALARM 4-Warning [chars] [chars]: [chars] The specified T1/E1 or T3/E3 Alarm has been asserted or cleared - "The recommended action is to isolate and repair the" " source of the asserted alarm" DTI-3-DTI_ERROR 3-Error DTI Error First DTI error message rfgw-sw-sup LOG_STD_NO_ACTION DTI-3-DTI_ERROR 3-Error DTI Error First DTI error message rfgw-sw-sup LOG_STD_NO_ACTION DTLS-3-REPLAY_ERROR_DTLS 3-Error DTLS anti-replay error src_addr: %Ci src_port: [dec] dest_addr: %Ci dst_port: [dec] Anti-replay error is encountered for this DTLS session. qfp-ipsec LOG_STD_ACTION DTLS-3-REPLAY_ERROR_IPV6_DTLS 3-Error DTLS anti-replay error ipv6 src_addr: [ipv6_addr] src_port: [dec] ipv6 dest_addr: [ipv6_addr] dst_port: [dec] Anti-replay error is encountered for this DTLS session. qfp-ipsec LOG_STD_ACTION DTP-4-MEM_UNAVAIL 4-Warning Memory was not available to perform the trunk negotiation action Unable to negotiate trunks because of a lack of memory - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." DTP-4-TMRERR 4-Warning An internal timer error occurred when trunking on interface [chars] There might be some instances in which a timer used by the trunking\n\ protocol expires at a time when it is unexpected. This problem is\n\ corrected internally. - "There is likely no long-term ramifications from this problem. However\n\ if further problems with trunking are seen it is recommended that you\n\ reload the device." DTP-4-UNKN_ERR 4-Warning An unknown operational error occurred Unable to negotiate trunks because an internal operation\n\ generated an error which was not expected to ever happen. - "Because of the unexpected nature of the problem the only recommended\n\ action is to reload the device" DTP-5-DOMAINMISMATCH 5-Notice Unable to perform trunk negotiation on port [chars] because of VTP domain mismatch. The two ports involved in trunk negotiation belong to different \n\ VTP domains. Trunking is possible only when the ports involved belong to\n\ the same VTP domain. dtp "Ensure that the two ports that are involved in trunk negotiation belong to\n\ the same VTP domain." DTP-5-ILGLCFG 5-Notice Illegal configonisl--ondot1q on [chars] The two ports on the link are set to the ON mode but one is set to\n\ 802.1Q encapsulation while the other is set to ISL encapsulation.\n\ When both ports on a link are set to the ON mode their encapsulation\n\ types must match - "Configure both ports on the link to have the same encapsulation." DTP-5-NONTRUNKPORTON 5-Notice Port [chars] has become non-trunk The specified port has changed from being a trunk port to an access\n\ port. - "" DTP-5-TRUNKPORTCHG 5-Notice Port [chars] has changed from [chars] trunk to [chars] trunk The specified trunk port has changed the encapsulation type is uses. - "" DTP-5-TRUNKPORTON 5-Notice Port [chars] has become [chars] trunk The specified port has changed from being an access port to a trunk\n\ port using the specified encapsulation. - "" dtsec-1-BAD_IDB 1-Alert Invalid Interface Descriptor Block The driver tried to fetch the interface's IDB and failed high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_MEDIA 1-Alert Unknown media-type in subblock The media-type specified in the driver subblock is invalid high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_PARTICLE 1-Alert Problem getting particle size The driver was unable to get the particle size for this interface high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_PLUGIN 1-Alert Plugin function table incomplete or missing The driver could not access the PA's specific function table high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_POOL 1-Alert Could not init buffer pools The driver failed to get a pool of buffers from IOS high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_SB_NOMEM 1-Alert [chars] - Cannot create IDB subblock due to insufficient memory There was insufficent system memory to create the subblock. high-gig-ethernet "The router requires more main memory." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_STRUCT 1-Alert Could not initialize structure The driver failed to initialize a structure high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-BAD_SUBBLOCK 1-Alert [chars] - Could not install or use IDB subblock An internal IOS error prevented the IDB subblock from being installed or used. high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-IDBTYPE_UNK 1-Alert Unknown IDBTYPE while starting driver The IDBTYPE in the interface's instance structure is undefined for this driver high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-INITFAIL_NOMEM 1-Alert [chars] initialization failed no buffer memory The Ethernet port initialization failed due to insufficient memory high-gig-ethernet "The router requires more packet memory - consider upgrade." LOG_STD_RECUR_ACTION dtsec-1-MODE_INVALID 1-Alert Unknown or invalid chip mode MII/TBI The driver subblock contains an invalid or undefined chip operating mode MII or TBI mode high-gig-ethernet "Software bug - open a case with Development Engineering." LOG_STD_SH_TECH_ACTION dtsec-1-RESET 1-Alert MAC Still in Reset An attempt was made to access the MAC while it was in reset high-gig-ethernet LOG_STD_SH_TECH_ACTION dtsec-2-NOISL 2-Critical Interface [chars] does not support ISL ISL is not supported on the specified interface's hardware. - LOG_STD_NO_ACTION dtsec-3-BAD_GBIC_EEPROM 3-Error [chars] - GBIC contains a bad EEPROM Interface contains a GBIC with a bad EEPROM. This causes the link to be down. high-gig-ethernet "Please make sure the GBIC type is compatible with the interface. " "Verify that the GBIC was obtained from Cisco or a supported vendor" dtsec-3-DUPLICATE 3-Error [chars] - duplicate GBIC The GBIC module for the interface specified in the error message is a duplicate of another GBIC in the system. As a result of the error both modules are disabled. high-gig-ethernet "Remove the duplicate module. If the problem persists LOG_STD_ACTION." dtsec-3-ERRINT 3-Error [chars] error interrupt mac_status = 0x%016llx The MAC controller has signalled an error condition. high-gig-ethernet LOG_STD_ACTION dtsec-3-MAC_LIMIT_EXCEEDED 3-Error Unable to add mac address [enet] Max number of allowed mac entries reached. Cannot add any more. - "Try removing some of the own mac addresses for example used by each" "unique hsrp group configuration. standby use-bia could be used to " "limit the usage" dtsec-3-NOT_SUPPORTED 3-Error [chars] - unsupported GBIC The GBIC module for the interface specified in the error message is not a Cisco-supported module. As a result of the error the module is disabled. high-gig-ethernet "Replace the module with a Cisco-supported GBIC. If the problem " "persists LOG_STD_ACTION." dtsec-3-TOOBIG 3-Error [chars] packet too big [dec] from [enet] The interface detects a packet larger than what is defined by MTU high-gig-ethernet "Check the other station's MTU setting" LOG_STD_NO_ACTION dtsec-3-UNKNOWN_GBIC 3-Error [chars] - Unknown GBIC type Interface contains a GBIC of unknown type. This causes the link to be down. high-gig-ethernet "Please make sure the GBIC type is compatible with the interface. " "Verify that the GBIC was obtained from Cisco or a supported vendor" DUAL-3-ANCHORCOUNT 3-Error Anchor count negative A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-ANCHORCOUNT 3-Error Anchor count negative A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-ANCHORCOUNT 3-Error Anchor count negative A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-ANCHORCOUNT 3-Error Anchor count negative A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-BADCOUNT 3-Error Route [chars] [dec] successors [dec] rdbs A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-BADCOUNT 3-Error Route [chars] [dec] successors [dec] rdbs A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-BADCOUNT 3-Error Route [chars] [dec] successors [dec] rdbs A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-BADCOUNT 3-Error Route [chars] [dec] successors [dec] rdbs A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." DUAL-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." DUAL-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." DUAL-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." DUAL-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." DUAL-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." DUAL-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." DUAL-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." DUAL-3-INTERNAL 3-Error [chars] [dec]: Internal Error A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-INTERNAL 3-Error [chars] [dec]: Internal Error A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-INTERNAL 3-Error [chars] [dec]: Internal Error A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-INTERNAL 3-Error [chars] [dec]: Internal Error A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-LINKSEXIST 3-Error Interface [chars] going down and [dec] links exist - - LOG_STD_ACTION DUAL-3-LINKSEXIST 3-Error Interface [chars] going down and [dec] links exist - - LOG_STD_ACTION DUAL-3-LINKSEXIST 3-Error Interface [chars] going down and [dec] links exist - - LOG_STD_ACTION DUAL-3-LINKSEXIST 3-Error Interface [chars] going down and [dec] links exist - - LOG_STD_ACTION DUAL-3-LINKSTILLUP 3-Error Link [dec] [chars] still exists on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-LINKSTILLUP 3-Error Link [dec] [chars] still exists on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-LINKSTILLUP 3-Error Link [dec] [chars] still exists on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-LINKSTILLUP 3-Error Link [dec] [chars] still exists on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-MULTIFLOW 3-Error Flow control error [chars] on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-MULTIFLOW 3-Error Flow control error [chars] on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-MULTIFLOW 3-Error Flow control error [chars] on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-MULTIFLOW 3-Error Flow control error [chars] on [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOBUFFER 3-Error No buffers available for [dec] byte packet The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory. - LOG_STD_SH_TECH_ACTION DUAL-3-NOBUFFER 3-Error No buffers available for [dec] byte packet The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory. - LOG_STD_SH_TECH_ACTION DUAL-3-NOBUFFER 3-Error No buffers available for [dec] byte packet The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory. - LOG_STD_SH_TECH_ACTION DUAL-3-NOBUFFER 3-Error No buffers available for [dec] byte packet The DUAL software was unable to allocate a packet buffer. The system\n\ may be out of memory. - LOG_STD_SH_TECH_ACTION DUAL-3-NOHANDLE 3-Error Handle [dec] is not allocated in pool. A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOHANDLE 3-Error Handle [dec] is not allocated in pool. A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOHANDLE 3-Error Handle [dec] is not allocated in pool. A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOHANDLE 3-Error Handle [dec] is not allocated in pool. A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOMATCH 3-Error Nexthop and infosource don't match. N = [chars] I = [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOMATCH 3-Error Nexthop and infosource don't match. N = [chars] I = [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOMATCH 3-Error Nexthop and infosource don't match. N = [chars] I = [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOMATCH 3-Error Nexthop and infosource don't match. N = [chars] I = [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOSOCKET 3-Error Unable to open socket for AS [dec] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOSOCKET 3-Error Unable to open socket for AS [dec] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOSOCKET 3-Error Unable to open socket for AS [dec] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-NOSOCKET 3-Error Unable to open socket for AS [dec] A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-PEERSEXIST 3-Error [dec] peers exist on IIDB [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-PEERSEXIST 3-Error [dec] peers exist on IIDB [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-PEERSEXIST 3-Error [dec] peers exist on IIDB [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-PEERSEXIST 3-Error [dec] peers exist on IIDB [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-PFXLIMIT 3-Error [chars] [dec]: [chars] prefix limit reached[dec]. Number of prefixes for eigrp has reached the configured or default limit. - "Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures." DUAL-3-PFXLIMIT 3-Error [chars] [dec]: [chars] prefix limit reached[dec]. Number of prefixes for eigrp has reached the configured or default limit. - "Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures." DUAL-3-PFXLIMIT 3-Error [chars] [dec]: [chars] prefix limit reached[dec]. Number of prefixes for eigrp has reached the configured or default limit. - "Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures." DUAL-3-PFXLIMIT 3-Error [chars] [dec]: [chars] prefix limit reached[dec]. Number of prefixes for eigrp has reached the configured or default limit. - "Use \"show ip eigrp accounting\" for details " "on the source of the prefixes and take corrective " "measures." DUAL-3-RDBLEFT 3-Error Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-RDBLEFT 3-Error Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-RDBLEFT 3-Error Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-RDBLEFT 3-Error Lingering DRDB deleting IIDB dest [chars] nexthop [chars] [chars] origin [chars] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-REFCOUNT 3-Error Negative refcount in pakdesc [hec] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-REFCOUNT 3-Error Negative refcount in pakdesc [hec] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-REFCOUNT 3-Error Negative refcount in pakdesc [hec] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-REFCOUNT 3-Error Negative refcount in pakdesc [hec] A software or hardware error occurred. - LOG_STD_ACTION DUAL-3-SIA 3-Error Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-SIA 3-Error Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-SIA 3-Error Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-SIA 3-Error Route [chars] stuck-in-active state in [chars] [dec]. Cleaning up A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-UNKTIMER 3-Error Unknown timer type [dec] expiration A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-UNKTIMER 3-Error Unknown timer type [dec] expiration A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-UNKTIMER 3-Error Unknown timer type [dec] expiration A hardware or software error occurred. - LOG_STD_ACTION DUAL-3-UNKTIMER 3-Error Unknown timer type [dec] expiration A hardware or software error occurred. - LOG_STD_ACTION DUAL-4-PFXLIMITTHR 4-Warning [chars] [dec]: [chars] threshold prefix level[dec] reached. - - - DUAL-4-PFXLIMITTHR 4-Warning [chars] [dec]: [chars] threshold prefix level[dec] reached. - - - DUAL-4-PFXLIMITTHR 4-Warning [chars] [dec]: [chars] threshold prefix level[dec] reached. - - - DUAL-4-PFXLIMITTHR 4-Warning [chars] [dec]: [chars] threshold prefix level[dec] reached. - - - DUAL-5-NBRCHANGE 5-Notice [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] A neighbor went up or down. - LOG_STD_NO_ACTION DUAL-5-NBRCHANGE 5-Notice [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] A neighbor went up or down. - LOG_STD_NO_ACTION DUAL-5-NBRCHANGE 5-Notice [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] A neighbor went up or down. - LOG_STD_NO_ACTION DUAL-5-NBRCHANGE 5-Notice [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] A neighbor went up or down. - LOG_STD_NO_ACTION DUAL-6-EVENT 6-Information [chars] [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-6-EVENT 6-Information [chars] [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-6-EVENT 6-Information [chars] [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-6-EVENT 6-Information [chars] [chars] A hardware or software error occurred. - LOG_STD_ACTION DUAL-6-NBRINFO 6-Information [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] Information regarding a neighbor. - LOG_STD_NO_ACTION DUAL-6-NBRINFO 6-Information [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] Information regarding a neighbor. - LOG_STD_NO_ACTION DUAL-6-NBRINFO 6-Information [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] Information regarding a neighbor. - LOG_STD_NO_ACTION DUAL-6-NBRINFO 6-Information [chars] [dec]: Neighbor [chars] [chars] is [chars]: [chars] Information regarding a neighbor. - LOG_STD_NO_ACTION DUP_ADDR_RCVD-3-LCON 3-Error ERRMSG_NOFLAGS - - - DUP_ADDR_RCVD-3-LCON 3-Error ERRMSG_NOFLAGS - - - DUP_IP_ADDRESS-2-MPLS_TE_PCALC 2-Critical ERRMSG_FLAG_TRACEBACK - - - DUP_IP_ADDRESS-2-MPLS_TE_PCALC 2-Critical ERRMSG_FLAG_TRACEBACK - - - DUP_RRR_ID-2-MPLS_TE_PCALC 2-Critical ERRMSG_FLAG_TRACEBACK - - - DUP_RRR_ID-2-MPLS_TE_PCALC 2-Critical ERRMSG_FLAG_TRACEBACK - - - DWDM-3-CLEAR_G709_CTR 3-Error Unable to clear g709 \ counter in slot [dec] rc = [dec] The SPA driver was unable to clear the G.709 OTN protocol counters for bit errors spa-eth-10ge "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-CONFIG_ALARM_REPORT 3-Error Failed to config report\n\ alarm [chars] slot [dec] rc = [dec] The SPA driver could not configure one of the reporting status of the alarms spa-eth-10ge "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-CONFIG_ALARM_THRESHOLD 3-Error Failed to config threshold \n\ alarm [chars] slot [dec] rc = [dec] The SPA driver could not configure one of the threshold alarms for the optical data or transport unit spa-eth-10ge "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-CONFIG_OVERHEAD_TTI 3-Error Failed to config [chars] [chars] slot [dec] rc = [dec] The LC driver could not configure the tail trace identifier for the optical data or transport unit - "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-CONFIG_PM 3-Error Failed to config [chars] [chars] slot [dec] rc = [dec] The LC driver could not configure the PM parameters for the optical data or transport unit - "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-CONFIG_TX_POWER 3-Error Failed to config \ transmit power [dec] on slot [dec] rc = [dec] The SPA driver detected a error in configuring the Tx power level for the UT2 transponder module spa-eth-10ge "Please power down and reseat the indicated SPA card. " "If the condition persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." DWDM-3-DWDM_CONFIG_FAIL 3-Error Failed to [chars] [chars] in slot [dec] rc = [dec] The SPA driver detected failure during configuring one of the DWDM parameters spa-eth-10ge "Reload the SPA card and if the problem" "persists call the tachnical assistance centre" DWDM-3-DWDM_GET_INFO_FAIL 3-Error Failed receiving [chars] \ from slot [dec] rc = [dec] The SPA driver did not receive the necessary optics information from the slot spa-eth-10ge "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-DWDM_NULL_INFO 3-Error DWDM info is NULL in [dec] The SPA driver detected NULL information for DWDM spa-eth-10ge "Reload the SPA and if the problem persists" "contact the technical support representative" DWDM-3-IPC_SHIM_INIT 3-Error DWDM IPC SHIM init failed The SPA driver detected failure during DWDM IPC SHIM initialization spa-eth-10ge "Please power down and reseat the indicated SPA card" "If the problem persists please contact your" "technical support representative" DWDM-3-LC_ERR_STATS 3-Error error sending LC stats to RP The SPA driver encountered an error while sending the LC stats to the RP spa-eth-10ge "Reload the SPA card and if the problem persists" "call the technical support representative" DWDM-3-MALLOC_FAIL 3-Error malloc failure creating \ G.709 port on slot [dec] The SPA driver detected a memory error on the SPA card spa-eth-10ge "Reload the card and if the problem persists " " call TAC" DWDM-3-OTN_STATS_CREATE_IF_FAIL 3-Error stats for interface index [dec] could not be created with status [dec] - snmp-otn "Copy the error message exactly as it appears and report it\n\ to your technical support representative." DWDM-3-OTN_STATS_CREATE_IF_FAILED_TO_ALLOCATE 3-Error stats for interface index [dec] could not be created with status [dec] - snmp-otn "Copy the error message exactly as it appears and report it\n\ to your technical support representative." DWDM-3-OTN_STATS_DELETE_IF_FAIL 3-Error stats for interface index [dec] could not be deleted with status [dec] - spa-eth-10ge "Copy the error message exactly as it appears and report it\n\ to your technical support representative." DWDM-3-RPC_FAILED 3-Error Application error rc = [dec]: The system failed to retrieve the information required to \n\ execute the command g709-dwdm show version DWDM-3-RPC_INIT_FAIL 3-Error DWDM RPC init failure The system failed to create the resources required to process user\n\ interface commands for transceivers. The error is not fatal but \n\ some \show\ commands could fail. g709-dwdm show version DWDM-3-RPC_PROCESSING_ERROR 3-Error DWDM RPC error: [chars] Non Fatal error occured in processing an RPC messsage. g709-dwdm show version DWDM-3-RX_G709_INFO 3-Error Failed receiving G709 info \ from slot [dec] rc = [dec] The SPA driver did not receive the necessary G.709 OTN protocol information from the slot spa-eth-10ge "Please check the configuration of the interfaces and controllers " "and correct the configuration if necessary. If the problem persists " "contact your Cisco technical support representative" DWDM-3-RX_LOS_THRESHOLD 3-Error Failed to config \ rx los threshold = [dec] on slot [dec] rc = [dec] The SPA driver detected an error in configuring the transponder receive power threshold spa-eth-10ge "Reload the SPA card and if the problem persists" "call TAC" DWDM-3-TIMER_ERR 3-Error Timer error The Driver did not obtain an expired timer from the timer tree for the DWDM process spa-eth-10ge "The SPA driver has encountered an error event on the SPA card." "If the condition persists copy the error message exactly as " "it appears or contact " "your technical support representative" DWDM-4-G709ALARM 4-Warning [chars]: [chars] [chars] The specified G709 Alarm has been declared or released g709-dwdm "Recommended action is to repair the source of the alarm." DWL-3-LOOP_BACK_DETECTED 3-Error Loop-back detected on [chars]. Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network. firmware "Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands." DYINGGASP-0-POWER_LOSS 0-Emergency Shutdown due to power loss This is a fail over message which is logged if this unit is about to shutdown due to power loss. - "Verify that the unit is powered on and power cables are" " connected correctly." DYINGGASP-6-HOST_NOT_SUPP 6-Information [chars] host [inet] is not supported for dyinggasp notification due to [chars]\n This message id logged if dying gasp ignores either SNMP or Syslog host for dying gasp notification. - "No action necessary" DYNCMD-3-CHAINADDFAIL 3-Error Parse chain link add failed for '[chars]' An error has occurred when a dynamic command is being added to the IOS command set. The commands specified will not be available. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-CHAINDELFAIL 3-Error Parse chain link delete failed for '[chars]' An error has occurred when a dynamic command is being removed from the IOS command set. The commands specified will stil not be available. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-FLAGSINUSE 3-Error New feature flags list [dec] invalid while feature flags in use [dec] IOS received a message to set the feature flags for the CLI. The message received to set the feature flags changed the number of feature flags which is unexpected. The message is ignored. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-FLAGSINVALID 3-Error New feature flag list values [dec] different than expected [dec] - - - DYNCMD-3-INIT 3-Error Dynamic command subsystem failed to initialize '[chars]' Some features depend on portions of the dynamic command infrastructure. Such features will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-LINKINVALIDALT 3-Error Link alternate node message received for node '[chars]' which cannot have an alternate. IOS received a message to add a command into the CLI. One of the messages to link nodes instructed IOS to link nodes which would result in an invalid construction. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-LINKINVALIDTRANS 3-Error Link transition '[chars]' message received for node '[chars]' which cannot have such a transition. IOS received a message to add a command into the CLI. One of the messages to link nodes instructed IOS to link nodes which would result in an invalid construction. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-LINKOUTOFSEQ 3-Error Create node message received when in mode '[chars]' IOS received a message to add a command node into the CLI. The message was received out of sequence iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-LINKUNKNOWNACCEPTNODE 3-Error Link node message received for unknown accept [chars] node '[dec]' - - - DYNCMD-3-LINKUNKNOWNALTNODE 3-Error Link node message received for unknown alternate node '[dec]' IOS received a message to add a command into the CLI. One of the messages to link nodes referenced a node unknown to IOS iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-LINKUNKNOWNNODE 3-Error Link node message received for unknown node '[dec]' IOS received a message to add a command into the CLI. One of the messages to link nodes referenced a node unknown to IOS iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGBIPCBUFFER 3-Error Unable to acquire a BIPC buffer for sending messages. A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGBIPCERR 3-Error Unable to process received BIPC messages for Dynamic Commands error: [chars] An unexpected condition has occurred while IOS was trying to process a received BIPC message for Dynamic Commands. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGBUILDERROR 3-Error Error '[dec]' building TDL message '[chars]' to send to the Shell Manager An unexpected condition has occurred while IOS is building a TDL message to send to the Shell Manager iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGDISPATCH 3-Error Unable to dispatch received TDL messages for Dynamic Commands An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages for Dynamic Commands. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGDISPATCHNULL 3-Error Received NULL TDL message An unexpected condition in which IOS has received a NULL TDL message for Dynamic Commands. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGENQUEUEERROR 3-Error Error queueing TDL message '[chars]' to send to the Shell Manager An unexpected condition has occurred when IOS attempted to queue a TDL message to send to the Shell Manager iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGERROR 3-Error Error '[chars]' handling a received TDL message '[chars]' for Dynamic Commands An unexpected condition has occurred while IOS is processing a received Dynamic Command TDL message iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGINVALIDFIELDINT 3-Error Invalid field '[chars]' in TDL message '[chars]' received: value '[dec]' for Dynamic Commands A message with an invalid field value was received for Dynamic Command creation iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGINVALIDFIELDSTR 3-Error Invalid field '[chars]' value '[chars]' in TDL message '[chars]' received for Dynamic Commands A message with an invalid field value was received for Dynamic Command creation iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGMARSHALERROR 3-Error Error '[dec]' marshaling TDL message '[chars]' to send to the Shell Manager An unexpected condition has occurred while IOS is marshaling TDL message to send to the Shell Manager iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-MSGMISSINGFIELD 3-Error Missing field '[chars]' in TDL message '[chars]' received from the Shell Manager A message missing a required field was received from the Shell Manager iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-NODEDUPLICATE 3-Error Create node message received for duplicate node '[dec]' IOS received a message to add a command into the CLI. One of the command nodes to be created has an identifier of an existing node. The new node is ignored. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-NODEOUTOFSEQ 3-Error Create node message received when in mode '[chars]' IOS received a message to add a command node into the CLI. The message was received out of sequence iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-NODETYPEUNKNOWN 3-Error Create node message received for unknown node type '[dec]' '[chars]' IOS received a message to add a command into the CLI. One of the command nodes to be created is of a type unknown to IOS iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGERR_LOG_FAIL 3-Error Failed to log errors for package '[chars]' An error has occurred updating the commandset for a newly installed package. The commands which failed to transfer could not be saved for further analysis. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGHANDLER_FILE_REMOVE 3-Error Package '[chars]' failed to remove: [chars] [chars] - - - DYNCMD-3-PKGHANDLER_FILE_WRITE 3-Error Package '[chars]' failed to write: [chars] [chars] - - - DYNCMD-3-PKGINT_API 3-Error Package interface failure for package '[chars]': [chars] Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_ARG 3-Error Incorrect argument type for package '[chars]' operation '[chars]': [chars] [dec] - - - DYNCMD-3-PKGINT_ARG_NUMBERVAL 3-Error Invalid argument value for package '[chars]' operation '[chars]': [dec] [dec] - - - DYNCMD-3-PKGINT_ARG_OPAQUEVAL 3-Error Invalid argument value for package '[chars]' operation '[chars]': %p [dec] - - - DYNCMD-3-PKGINT_ARGS 3-Error Incorrect argument count for package '[chars]' operation '[chars]': [dec] not [dec] An error has occurred loading the commandset for a newly installed package. The package is not compatible with the running IOS instance. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_DIR_CREATE 3-Error Package integration failed to create directory: [chars] [chars] - - - DYNCMD-3-PKGINT_DIR_MOVE 3-Error Package integration failed to move directory: [chars] to [chars] [chars] - - - DYNCMD-3-PKGINT_DIR_OPEN 3-Error Package integration failed to open directory: [chars] [chars] - - - DYNCMD-3-PKGINT_DIR_REMOVE 3-Error Package integration failed to remove directory: [chars] [chars] - - - DYNCMD-3-PKGINT_FILE_OPEN 3-Error Package integration failed to open file: [chars] [chars] - - - DYNCMD-3-PKGINT_FILE_REMOVE 3-Error Package integration failed to remove: [chars] [chars] - - - DYNCMD-3-PKGINT_INSTALL 3-Error Failed to install '[chars]': [chars] Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_LOAD 3-Error Failed to load '[chars]': [chars] Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_LOCK 3-Error Failed to acquire package list lock for [chars]: [chars] An error occurred when a configuration package was being installed or removed. This may indicate a timeout which may be a temporary condition. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_OFFSET 3-Error Invalid offset argument for package '[chars]' operation '[chars]': [chars] [dec] - - - DYNCMD-3-PKGINT_PKGLOCK 3-Error [chars] failed to acquire package lock for [chars] An error occurred when locking a configuration package. The package needs to be locked for processing configuration commands or timer-based processing of configuration data. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_SYMBOL 3-Error Package [chars] incompatible: symbol '[chars]' is of type [chars] expected [chars] Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_UNLOCK 3-Error Failed to release the package list lock: [chars] An error occurred when a configuration package was being installed or removed. This should not occur. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGINT_VALIDATE 3-Error Failed to validate '[chars]': [chars] Some features' configuration depends on a packaging infrastructure. Packaged configuration for the specified package will be unavailable. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-PKGNODE_ADD_FAIL 3-Error Parse node add failed for package '[chars]' [chars] [dec] - - - DYNCMD-3-TREETOP 3-Error Unable to link top-level keyword '[chars]' into parse tree IOS received a message to add a command into the CLI. The appropriate location to link in the command could not be found. iosxe-shellmgr LOG_STD_ACTION DYNCMD-3-TREETOPNOTKW 3-Error The top-level parser transition '[chars]' is not a keyword IOS received a message to add a command into the CLI. The top-level node must be a keyword node. iosxe-shellmgr LOG_STD_ACTION DYNCMD-7-CMDSET_LOADED 7-Debug The Dynamic Command set has been loaded from the Shell Manager IOS has completed loading the set of commands published and processed by components running in packages other than the IOS package. iosxe-shellmgr LOG_STD_NO_ACTION DYNCMD-7-CMDSET_UNLOADED 7-Debug The Dynamic Command set from the Shell Manager has been unloaded IOS has completed unloading the Dynamic Command set. This should only occur when a new package has been installed and should shortly be followed by a message indicating that the new Dynamic Command set has been loaded. iosxe-shellmgr LOG_STD_NO_ACTION DYNCMD-7-PKGINT_INSTALLED 7-Debug The command package '[chars]' has been succesfully installed IOS has completed installation of the specified command package. Configuration commands for the package are now available. iosxe-shellmgr LOG_STD_NO_ACTION DYNCMD-7-PKGINT_UNINSTALLED 7-Debug The command package '[chars]' has been succesfully uninstalled IOS has completed uninstallation of the specified command package. Configuration commands for the package are no longer available. iosxe-shellmgr LOG_STD_NO_ACTION E_CFM-2-INIT_ALLOC_FAIL 2-Critical Failed to allocate memory required for initialization. CFM failed to allocate a memory required for the feature to operate correctly. This likely indicates a resource limitation or an attempt to use the software on unsupported hardware. ethernet-cfm "Confirm that the configured scale does not exceed the permitted limits " "for the hardware and that any other resource issues are resolved. If " "problems are still observed copy the error message exactly as it " "appears on the console or in the system log call your Cisco technical " "support representative and provide the representative with the " "gathered information. " E_CFM-2-INIT_ALLOC_FAIL 2-Critical Failed to allocate memory required for initialization. CFM failed to allocate a memory required for the feature to operate correctly. This likely indicates a resource limitation or an attempt to use the software on unsupported hardware. ethernet-cfm "Confirm that the configured scale does not exceed the permitted limits " "for the hardware and that any other resource issues are resolved. If " "problems are still observed copy the error message exactly as it " "appears on the console or in the system log call your Cisco technical " "support representative and provide the representative with the " "gathered information. " E_CFM-2-PD_CAPABILITY_UPDATE 2-Critical Platform has indicated an invalid capability update which has been ignored. Platform code has indicated that its capabilities have changed based on a configuration knob but the updated values were inconsistent. ethernet-cfm "This likely indicates a programming error in Platform code but should " "not present a problem unless either of MA Alias and SLM over xconnect " "features are required. See documentation for this platform/release." E_CFM-2-PD_CAPABILITY_UPDATE 2-Critical Platform has indicated an invalid capability update which has been ignored. Platform code has indicated that its capabilities have changed based on a configuration knob but the updated values were inconsistent. ethernet-cfm "This likely indicates a programming error in Platform code but should " "not present a problem unless either of MA Alias and SLM over xconnect " "features are required. See documentation for this platform/release." E_CFM-3-CONFIG_ERROR 3-Error CFM mis-configuration in the network. Continuity-check message is received from mac-address [enet] with duplicated mpid [dec] as configured locally for service MA name [chars] with [chars] of domain [chars]. The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association." E_CFM-3-CONFIG_ERROR 3-Error CFM mis-configuration in the network. Continuity-check message is received from mac-address [enet] with duplicated mpid [dec] as configured locally for service MA name [chars] with [chars] of domain [chars]. The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association." E_CFM-3- CONFIG_LOST 3-Error Failed to update CFM internal state to reflect configuration change: [chars] CFM failed to save the CFM configuration in response to the recent change. The reason for this may be due to a memory shortage. The user should resolve any memory problems and then check the CFM configuration and if necessary re-add any config that is missing. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- CONFIG_LOST 3-Error Failed to update CFM internal state to reflect configuration change: [chars] CFM failed to save the CFM configuration in response to the recent change. The reason for this may be due to a memory shortage. The user should resolve any memory problems and then check the CFM configuration and if necessary re-add any config that is missing. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3-CROSS_CONNECTED_SERVICE 3-Error Continuity Check message is received from remote MEP mpid [dec] with service MA name [chars] [chars] MAC: [enet] for service MA name [chars] of domain [chars] level [dec]. The Continuity Check message whose MA name or MA level is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network. ethernet-cfm "Configure the CFM MA name or MA level properly across " "the network." E_CFM-3-CROSS_CONNECTED_SERVICE 3-Error Continuity Check message is received from remote MEP mpid [dec] with service MA name [chars] [chars] MAC: [enet] for service MA name [chars] of domain [chars] level [dec]. The Continuity Check message whose MA name or MA level is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network. ethernet-cfm "Configure the CFM MA name or MA level properly across " "the network." E_CFM-3-CROSSCHECK_MEP_MISSING 3-Error The device does not receive any CC messages from a remote MEP with mpid [dec] MA name [chars] that it was expecting to be part of the [chars] in the domain [chars]. The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. " E_CFM-3-CROSSCHECK_MEP_MISSING 3-Error The device does not receive any CC messages from a remote MEP with mpid [dec] MA name [chars] that it was expecting to be part of the [chars] in the domain [chars]. The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. " E_CFM-3-CROSSCHECK_MEP_UNKNOWN 3-Error The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the MA name [chars] in the domain: [chars]. The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Check whether the CFM crosscheck configurations " "are proper." E_CFM-3-CROSSCHECK_MEP_UNKNOWN 3-Error The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the MA name [chars] in the domain: [chars]. The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Check whether the CFM crosscheck configurations " "are proper." E_CFM-3-FAULT_ALARM 3-Error A fault has occurred in the network for the local MEP having mpid [dec] [chars] for service MA name [chars] with the event code [chars]. This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other MA. ethernet-cfm "There could be a possible fault in the network. " "Check whether the cfm configurations are proper." E_CFM-3-FAULT_ALARM 3-Error A fault has occurred in the network for the local MEP having mpid [dec] [chars] for service MA name [chars] with the event code [chars]. This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other MA. ethernet-cfm "There could be a possible fault in the network. " "Check whether the cfm configurations are proper." E_CFM-3-FORWARDING_LOOP 3-Error Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the MA name [chars]. The device is receiving its own CC messages for a particular vlan or evc within the same MA. ethernet-cfm "Configure the CFM maintenance points properly " "to avoid the forwarding loop." E_CFM-3-FORWARDING_LOOP 3-Error Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the MA name [chars]. The device is receiving its own CC messages for a particular vlan or evc within the same MA. ethernet-cfm "Configure the CFM maintenance points properly " "to avoid the forwarding loop." E_CFM-3-LR_FROM_WRONG_FP 3-Error received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination An unknown destination sent a reply to a Loopback messages that was intended to another device. ethernet-cfm "Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message." E_CFM-3-LR_FROM_WRONG_FP 3-Error received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination An unknown destination sent a reply to a Loopback messages that was intended to another device. ethernet-cfm "Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message." E_CFM-3- MAC_STATUS_CHANGE_FAIL 3-Error Failed to set MAC layer operational state for [chars] to [chars]. CFM failed to update the state of the MAC layer for the specified interface in response to a change in the errors detected on the interface. If the MAC layer state is incorrect it is possible that data traffic flow through the interface will be affected either by traffic unexpectedly being allowed to pass through the interface or by traffic unexpectedly being dropped. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- MAC_STATUS_CHANGE_FAIL 3-Error Failed to set MAC layer operational state for [chars] to [chars]. CFM failed to update the state of the MAC layer for the specified interface in response to a change in the errors detected on the interface. If the MAC layer state is incorrect it is possible that data traffic flow through the interface will be affected either by traffic unexpectedly being allowed to pass through the interface or by traffic unexpectedly being dropped. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- OIR_RESTORE 3-Error Failed to restore CFM configuration on OIR insertion: [chars] CFM failed to restore the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface instead. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- OIR_RESTORE 3-Error Failed to restore CFM configuration on OIR insertion: [chars] CFM failed to restore the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface instead. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- OIR_SAVE 3-Error Failed to save CFM configuration on OIR removal: [chars] CFM failed to save the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface on reinsertion. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3- OIR_SAVE 3-Error Failed to save CFM configuration on OIR removal: [chars] CFM failed to save the CFM configuration that was previously present on the interface prior to the OIR event. The user may need to be manually reconfigure the interface on reinsertion. ethernet-cfm "Collect the output of show tech-support ethernet-cfm " "as soon as possible after the problem is seen. " LOG_STD_ACTION E_CFM-3-REMOTE_MEP_DOWN 3-Error Remote MEP mpid [dec] [chars] MA name [chars] in domain [chars] changed state to down with event code [chars]. The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB ethernet-cfm "Check the remote CFM configurations using CFM " " utilities like traceroute and ping." E_CFM-3-REMOTE_MEP_DOWN 3-Error Remote MEP mpid [dec] [chars] MA name [chars] in domain [chars] changed state to down with event code [chars]. The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB ethernet-cfm "Check the remote CFM configurations using CFM " " utilities like traceroute and ping." E_CFM-3- TIMEOUT_TOO_SMALL 3-Error Attempted to start a timer with a value less than the minimum permitted [dec]ms defaulting to [dec]ms. - - - E_CFM-3- TIMEOUT_TOO_SMALL 3-Error Attempted to start a timer with a value less than the minimum permitted [dec]ms defaulting to [dec]ms. - - - E_CFM-6-CROSSCHECK_SERVICE_UP 6-Information The device received CC messages from all remote MEPs within a given MA name [chars] in the maintenance domain [chars]. The service configured either MA is up as it receives CC messages from all remote statically configured MEPs. ethernet-cfm "Information message only." E_CFM-6-CROSSCHECK_SERVICE_UP 6-Information The device received CC messages from all remote MEPs within a given MA name [chars] in the maintenance domain [chars]. The service configured either MA is up as it receives CC messages from all remote statically configured MEPs. ethernet-cfm "Information message only." E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_STATE_CHANGE 6-Information Ethernet Dataplane Latching Loopback state change [chars] Dataplane Latching Loopback state changed for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_STATE_CHANGE 6-Information Ethernet Dataplane Latching Loopback state change [chars] Dataplane Latching Loopback state changed for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_TIMER_EXPIRED 6-Information Ethernet Dataplane Latching Loopback timer expired [chars] Dataplane Latching Loopback timer is expired for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_CONT_TIMER_EXPIRED 6-Information Ethernet Dataplane Latching Loopback timer expired [chars] Dataplane Latching Loopback timer is expired for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_START 6-Information Ethernet Dataplane Latching Loopback Start on [chars] Dataplane Latching Loopback is activated for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_START 6-Information Ethernet Dataplane Latching Loopback Start on [chars] Dataplane Latching Loopback is activated for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_STOP 6-Information Ethernet Dataplane Latching Loopback Stop on [chars] Dataplane Latching Loopback is de-activated for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_STOP 6-Information Ethernet Dataplane Latching Loopback Stop on [chars] Dataplane Latching Loopback is de-activated for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_EXPIRED 6-Information Ethernet Dataplane Latching Loopback timer expired on [chars] Dataplane Latching Loopback timer is expired for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_EXPIRED 6-Information Ethernet Dataplane Latching Loopback timer expired on [chars] Dataplane Latching Loopback timer is expired for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_RESTARTED 6-Information Ethernet Dataplane Latching Loopback timer restarted on [chars] Dataplane Latching Loopback timer is restarted for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-DATAPLANE_LATCHING_LOOPBACK_TIMER_RESTARTED 6-Information Ethernet Dataplane Latching Loopback timer restarted on [chars] Dataplane Latching Loopback timer is restarted for the specified service ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_AIS 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters AIS defect condition Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_AIS 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters AIS defect condition Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_AIS_INT 6-Information Interface [chars] enters AIS defect condition for [chars] direction Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_AIS_INT 6-Information Interface [chars] enters AIS defect condition for [chars] direction Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_LCK 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters LCK defect condition Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_LCK 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] enters LCK defect condition Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_LCK_INT 6-Information Interface [chars] enters LCK defect condition for [chars] direction Interface is put in OOS state through exec cli for input direction ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-ENTER_LCK_INT 6-Information Interface [chars] enters LCK defect condition for [chars] direction Interface is put in OOS state through exec cli for input direction ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_AIS 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited AIS defect condition Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_AIS 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited AIS defect condition Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_AIS_INT 6-Information Interface [chars] exited AIS defect condition for [chars] direction LOG_STD_NO_ACTION ethernet-cfm "Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state" E_CFM-6-EXIT_AIS_INT 6-Information Interface [chars] exited AIS defect condition for [chars] direction LOG_STD_NO_ACTION ethernet-cfm "Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state" E_CFM-6-EXIT_LCK 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited LCK defect condition Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_LCK 6-Information local mep with mpid [dec] level [dec] [chars] dir [chars] Interface [chars] exited LCK defect condition Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep service id. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_LCK_INT 6-Information Interface [chars] exited LCK defect condition for [chars] direction Interface has exited LCK defect condition. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-EXIT_LCK_INT 6-Information Interface [chars] exited LCK defect condition for [chars] direction Interface has exited LCK defect condition. ethernet-cfm "LOG_STD_NO_ACTION" E_CFM-6-MAX_MEPS_EXCEEDED 6-Information Maximum MEPs threshold exceeded in [chars] for domain [chars] service [chars] mac [enet] mpid [dec] The number of remote MEP entries in CC database has exceeded the maximum MEPs configured. The current remote MEP is not saved in the CC database. ethernet-cfm "Verify that the correct number for maximum MEPs is specified in the " "configuration. If correct number of maximum MEPs is configured " "verify if any unexpected remote MEP is not part of the service via " "'show ethernet cfm maintenance remote' or 'show ethernet cfm mpdb' " "command" E_CFM-6-MAX_MEPS_EXCEEDED 6-Information Maximum MEPs threshold exceeded in [chars] for domain [chars] service [chars] mac [enet] mpid [dec] The number of remote MEP entries in CC database has exceeded the maximum MEPs configured. The current remote MEP is not saved in the CC database. ethernet-cfm "Verify that the correct number for maximum MEPs is specified in the " "configuration. If correct number of maximum MEPs is configured " "verify if any unexpected remote MEP is not part of the service via " "'show ethernet cfm maintenance remote' or 'show ethernet cfm mpdb' " "command" E_CFM-6-REMOTE_MEP_UP 6-Information Continuity Check message is received from a remote MEP with mpid [dec] [chars] MA name [chars] domain [chars] interface status [chars] event code [chars]. A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Information message only." E_CFM-6-REMOTE_MEP_UP 6-Information Continuity Check message is received from a remote MEP with mpid [dec] [chars] MA name [chars] domain [chars] interface status [chars] event code [chars]. A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MA. ethernet-cfm "Information message only." E911-3-MISSING_DEFAULT_NUMBER 3-Error It is mandatory to configure an ELIN under 'voice emergency response settings.' The administrator has enabled the Enhanced 911 feature without configuring\n\ a default ELIN under 'voice emergency response settings.' voice-ivr "The administrator should enter the 'voice emergency response settings' \n\ mode and configure a value for the 'elin' CLI." E911-3-MISSING_DEFAULT_NUMBER 3-Error It is mandatory to configure an ELIN under 'voice emergency response settings.' The administrator has enabled the Enhanced 911 feature without configuring\n\ a default ELIN under 'voice emergency response settings.' voice-ivr "The administrator should enter the 'voice emergency response settings' \n\ mode and configure a value for the 'elin' CLI." E911-4-CALLBACK_UNREACHABLE 4-Warning Unable to contact the last emergency caller at [chars]. A call has been made to an emergency response number. \n\ This message simply informs system administrators of the call. voice-ivr "The administrator determines the policy for\n\ outbound emergency calls. The administrator\n\ may set-up an application to page or email\n\ a technician everytime this message is emitted." E911-4-CALLBACK_UNREACHABLE 4-Warning Unable to contact the last emergency caller at [chars]. A call has been made to an emergency response number. \n\ This message simply informs system administrators of the call. voice-ivr "The administrator determines the policy for\n\ outbound emergency calls. The administrator\n\ may set-up an application to page or email\n\ a technician everytime this message is emitted." EAP-2-PROCESS_ERR 2-Critical [chars] This is critical condition where the router could not perform EAP\n\ process related operation. eap "Reload the device." EAP-2-PROCESS_ERR 2-Critical [chars] This is critical condition where the router could not perform EAP\n\ process related operation. eap "Reload the device." EAP-4-BADPKT 4-Warning IP=[inet]| HOST=[chars] This messages informs that the router received an invalid or malformed\n\ EAP packet from the specified host. eap "Check specified host for EAP operation." EAP-4-BADPKT 4-Warning IP=[inet]| HOST=[chars] This messages informs that the router received an invalid or malformed\n\ EAP packet from the specified host. eap "Check specified host for EAP operation." EAP-6-MPPE_KEY 6-Information IP=[chars]| MPPE_RECV_KEY_LENGTH=[dec] This messages informs that the router received MPPE KEY for the specified\n\ host. eap "No action is required." EAP-6-MPPE_KEY 6-Information IP=[chars]| MPPE_RECV_KEY_LENGTH=[dec] This messages informs that the router received MPPE KEY for the specified\n\ host. eap "No action is required." EC-3-BWMISMATCH 3-Error [chars] should be removed from the Port-channel[dec] The member-link shouldn't have been part of the port-channel bundle\n\ because the bandwidth of the member-link doesn't match the bandwidth\n\ of the bundle. This configuration shouldn't have been allowed. This error\n\ indicates it was allowed due to some software issue. fec "Remove the member-link from the port-channel for\n\ proper operation." EC-5-MINLINKS_MET 5-Notice Port-channel [chars] is up as its bundled ports [dec] meets min-links The administrative configuration of minimum links is equal or less than\n\ the number of bundled ports. Therefore this port channel has been\n\ brought up fec "None." EC-5-MINLINKS_NOTMET 5-Notice Port-channel [chars] is down bundled ports [dec] doesn't meet min-links The administrative configuration of minimum links is greater than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ down fec "Reduce the min-links configuration for this group\n\ or add more ports to this port-channel to have\n\ them bundle." ECC-2-MALLOC 2-Critical Attempt to malloc [dec] bytes for the ECC error log failed.\n ECC errors will only be reported and not recorded.\n Malloc for the ECC error log failed. A memory upgrade would be advisable or is recommended. - LOG_STD_ACTION ECC-3-SBE_HARD 3-Error Single bit *hard* error detected at 0x%08x A single-bit uncorrectable error [hard error] was detected on a CPU\n\ read from DRAM. 'show ecc' will dump the Single-bit errors logged thus\n\ far and will also indicate detected hard error address locations. - "Monitor system through 'show ecc' and replace DRAM if too many\n\ such errors." ECC-3-SBE_LIMIT 3-Error Single bit error detected and corrected\nat 0x%08x A single-bit correctable error was detected on a CPU read from DRAM. - LOG_STD_ACTION ECC-3-SBE_RMW_LIMIT 3-Error Single bit error detected and corrected at 0x%08x on a read-modify-write cycle A single-bit correctable error was detected on during a read-modify-\n\ write cycle on a CPU read from DRAM for a non 8-byte access.\n\ 'show ecc' can be used to dump Single-bit errors logged thus far. - LOG_STD_ACTION ECC-3-SYNDROME_SBE_LIMIT 3-Error 8-bit Syndrome for the detected Single-bit error: 0x[hec] The 8-bit syndrome for detected single-bit error. This value does not\n\ indicate the exact positions of the bits in error but can be used to\n\ approximate their positions. - LOG_STD_ACTION ECFM_HA-2-GET_BUFFER 2-Critical ECFM ISSU client failed to get buffer for message. Error: [dec] [chars] The ECFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ecfm "show logging and show checkpoint client" ECFM_HA-2-GET_BUFFER 2-Critical ECFM ISSU client failed to get buffer for message. Error: [dec] [chars] The ECFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ecfm "show logging and show checkpoint client" ECFM_HA-2-INIT 2-Critical ECFM ISSU client initialization failed to [chars]. Error: [dec] [chars] The ECFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ecfm LOG_STD_ACTION ECFM_HA-2-INIT 2-Critical ECFM ISSU client initialization failed to [chars]. Error: [dec] [chars] The ECFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ecfm LOG_STD_ACTION ECFM_HA-2-SEND_NEGO_FAILED 2-Critical ECFM ISSU client failed to send negotiation message. Error: [dec] [chars] The ECFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ecfm "show logging and show checkpoint client" ECFM_HA-2-SEND_NEGO_FAILED 2-Critical ECFM ISSU client failed to send negotiation message. Error: [dec] [chars] The ECFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ecfm "show logging and show checkpoint client" ECFM_HA-2-SESSION_NEGO 2-Critical ECFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The ECFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ecfm "show issu session and " "show issu negotiated capability " ECFM_HA-2-SESSION_NEGO 2-Critical ECFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The ECFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ecfm "show issu session and " "show issu negotiated capability " ECFM_HA-2-SESSION_REGISTRY 2-Critical ECFM ISSU client failed to register session information. Error: [dec] [chars] The ECFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ecfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ECFM_HA-2-SESSION_REGISTRY 2-Critical ECFM ISSU client failed to register session information. Error: [dec] [chars] The ECFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ecfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ECFM_HA-3-INVALID_SESSION 3-Error ECFM ISSU client does not have a valid registered session. The ECFM ISSU client does not have a valid registered session. ecfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ECFM_HA-3-INVALID_SESSION 3-Error ECFM ISSU client does not have a valid registered session. The ECFM ISSU client does not have a valid registered session. ecfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ECFM_HA-3- ISSU 3-Error YO Hi ecfm "Hello " LOG_STD_ACTION ECFM_HA-3- ISSU 3-Error YO Hi ecfm "Hello " LOG_STD_ACTION ECFM_HA-3-MSG_NOT_OK 3-Error ECFM ISSU client 'Message Type [dec]' is not compatible The ECFM ISSU client received an incompatible message from the peer device. The message cannot be processed. ecfm "show issu message group and " "show issu session and " "show issu negotiated version " ECFM_HA-3-MSG_NOT_OK 3-Error ECFM ISSU client 'Message Type [dec]' is not compatible The ECFM ISSU client received an incompatible message from the peer device. The message cannot be processed. ecfm "show issu message group and " "show issu session and " "show issu negotiated version " ECFM_HA-3-MSG_SIZE 3-Error ECFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The ECFM ISSU client failed to calculate the MTU for the specified message. The ECFM ISSU client will not able to send the message to the standby device. ecfm "show issu message group and " "show issu session and " "show issu negotiated version " ECFM_HA-3-MSG_SIZE 3-Error ECFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The ECFM ISSU client failed to calculate the MTU for the specified message. The ECFM ISSU client will not able to send the message to the standby device. ecfm "show issu message group and " "show issu session and " "show issu negotiated version " ECFM_HA-3-SESSION_UNREGISTRY 3-Error ECFM ISSU client failed to unregister session information. Error: [dec] [chars] The ECFM ISSU client failed to unregister session information. ecfm "show issu session and " "show issu negotiated capability " ECFM_HA-3-SESSION_UNREGISTRY 3-Error ECFM ISSU client failed to unregister session information. Error: [dec] [chars] The ECFM ISSU client failed to unregister session information. ecfm "show issu session and " "show issu negotiated capability " ECFM_HA-3-TRANSFORM 3-Error ECFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The ECFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ECFM state between the active device and the standby device is not identical. ecfm "show issu session and " "show issu negotiated version " ECFM_HA-3-TRANSFORM 3-Error ECFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The ECFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ECFM state between the active device and the standby device is not identical. ecfm "show issu session and " "show issu negotiated version " ECFM_HSBY-5-FAIL 5-Notice Communication lost with remote ODU for link protection group [dec] on [chars] Communication was lost with the remote outdoor unit ODU due to either a CC message timeout or the interface going down. uea-eoam LOG_STD_NO_ACTION ECFM_HSBY-5-FAILOVER 5-Notice Failover from [chars] to [chars] in link protection group [dec]. The active outdoor unit ODU in the link protection group either has sent a message to the indoor unit IDU uea-eoam LOG_STD_NO_ACTION ECFM_HSBY-5-KO 5-Notice Remote ODU for link protection group [dec] on [chars] has indicated a failure The remote outdoor unit ODU has raised its Sender KO flag indicating a failure. uea-eoam LOG_STD_NO_ACTION ECFM_HSBY-5-OK 5-Notice Remote ODU for link protection group [dec] on [chars] is now ok. The previously failed remote outdoor unit ODU has recovered. uea-eoam LOG_STD_NO_ACTION ECFM_HSBY-5-PORT_ACTIVE 5-Notice [chars] link protection group [dec] now forwarding traffic The remote outdoor unit ODU connected to this interface is now active. This interface is now forwarding traffic to/from the remote ODU. uea-eoam LOG_STD_NO_ACTION ECFM_HSBY-5-SUSPEND 5-Notice Remote ODU for link protection group [dec] on [chars] is now suspended. The remote outdoor unit ODU has requested monitoring of CC messages be temporarily suspended. uea-eoam LOG_STD_NO_ACTION ECFM_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical QFP ECFM Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP ECFM Proxy initialization detected that the IPC interface initialization failed. QFP ECFM proxy will not be functional while this condition exists. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-3-ECFM_MEM_EXTEND_FAILED 3-Error ECFM IPC subtype: [dec] Extending memory failed. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-3-ECFM_MEM_REQ_FAILED 3-Error ECFM IPC subtype: [dec] Requesting more memory failed. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-3-PROXY_BAD_MSG 3-Error QFP ECFM Proxy received bad length message type [dec] Cisco internal software error. QFP ECFM Proxy received a corrupted message from control plane. This message will be ignored. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error QFP ECFM Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. QFP ECFM Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error QFP ECFM Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. QFP ECFM Proxy message processing detected a message sent failure. The message is lost as the result of this condition. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-4-PROXY_INVALID_MSG 4-Warning QFP ECFM Proxy received invalid message type [dec] Cisco internal software error. QFP ECFM Proxy received an invalid message from control plane. This message will be ignored. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECFM_PROXY-4-PROXY_INVALID_MSG_LEN 4-Warning QFP ECFM Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Cisco internal software error. QFP ECFM Proxy received invalid IPC message length from control plane. This message will be ignored. asr1k-ecfm keyword:ecfm LOG_STD_ACTION ECODE_DOWNLOAD-0-INTERNAL_PANIC 0-Emergency [chars] A Panic Condition. - "" ECODE_DOWNLOAD-1-INITFAIL 1-Alert msgtxt_initfail - - - ECODE_DOWNLOAD-1-NOMEMORY 1-Alert msgtxt_nomemory - - - ECODE_DOWNLOAD-3-INTERNAL_ERROR 3-Error [chars] Errors - "" ECODE_DOWNLOAD-7-INTERNAL_ASSERT 7-Debug [chars]: [chars] Assertion Failure - File [chars] Line [dec] Assertion - "" EDSP-4-CEF_TOOLONG 4-Warning CEF to SCCP devices may be disabled! See message below. Given up waiting for CEF initialization to complete. cme-ephone "Check the message about CEF and the EDSP0 interface below. If the" " vector is EVENTUALLY set to Null CEF RTP sending for SCCP devices is" " disabled. You may try to recover by restarting \"ip cef\" in IOS" " configuration." EDSP-4-CEF_TOOLONG 4-Warning CEF to SCCP devices may be disabled! See message below. Given up waiting for CEF initialization to complete. cme-ephone "Check the message about CEF and the EDSP0 interface below. If the" " vector is EVENTUALLY set to Null CEF RTP sending for SCCP devices is" " disabled. You may try to recover by restarting \"ip cef\" in IOS" " configuration." EDSP-6-CEF_WAIT 6-Information Waiting for CEF initialization to complete first ... [dec] Initialization of CEF RTP sending relies on system's CEF readiness. cme-ephone LOG_STD_NO_ACTION EDSP-6-CEF_WAIT 6-Information Waiting for CEF initialization to complete first ... [dec] Initialization of CEF RTP sending relies on system's CEF readiness. cme-ephone LOG_STD_NO_ACTION EDSP-6-IPV6_ENABLED 6-Information IPv6 on interface [chars] added. IPv6 capability has been enabled for the sub-interface. cme-ephone LOG_STD_NO_ACTION EDSP-6-IPV6_ENABLED 6-Information IPv6 on interface [chars] added. IPv6 capability has been enabled for the sub-interface. cme-ephone LOG_STD_NO_ACTION EDSP-6-IPV6_FAILED 6-Information IPv6 on interface [chars] failed. IPv6 initialization has failed for the sub-interface. cme-ephone "Please check IPv6 and interface related configurations." EDSP-6-IPV6_FAILED 6-Information IPv6 on interface [chars] failed. IPv6 initialization has failed for the sub-interface. cme-ephone "Please check IPv6 and interface related configurations." EDSP-6-VEC_CHANGE 6-Information EDSP0's LES switching vector set to [chars] To monitor CEF initialization for the hidden interface. cme-ephone LOG_STD_NO_ACTION EDSP-6-VEC_CHANGE 6-Information EDSP0's LES switching vector set to [chars] To monitor CEF initialization for the hidden interface. cme-ephone LOG_STD_NO_ACTION EHSA-2-EHSALOAD 2-Critical [chars] Netbooting was attempted on an EHSA Secondary - "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-2-EHSASW 2-Critical [chars] Primary has crashed or is unresponsive. Secondary is taking over - "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-EHSABADST 3-Error [chars] [[dec]] [[dec]] EHSA internal error. Determine the component from the stack trace and process name displayed in the error message. Use Topic to search for a similar DDTS. If you find none write a DDTS for this problem. "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-EHSAINT 3-Error '[chars]' at level [dec] EHSA internal error. Determine the component from the stack trace and process name displayed in the error message. Use Topic to search for a similar DDTS. If you find none write a DDTS for this problem. If the stack trace indicates that the scheduler was called from an interrupt handler choose the DDTS component based on the interrupt handler. Otherwise use the process name to determine the DDTS component. "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-IPCERR 3-Error [chars] [[chars]] IPC failed for EHSA. EHSA messages cannot be transmitted . - "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-KEEPTO 3-Error No keepalive seen in [[dec]] secs: Failover [chars] EHSA keepalive failure. - "Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-NOBUF 3-Error [chars] The IPC ran out of memory buffers. - "Reduce the number of applications currently running on the IPC. Copy the error message exactly as it appears and report it to your technical support representative." EHSA-3-STCHNG 3-Error [chars] [[dec]] EHSA State change detected - "Copy the error message exactly as it appears and report it to your technical support representative." EIO-3- NOCDB 3-Error Unable to create controller cdb. failed to create controller cdb. - LOG_STD_ACTION EIO-3- NOCHUNK 3-Error Unable to create memory chunk. failed to create memory chunk. - LOG_STD_ACTION EIO-3- NOMEM 3-Error out of memory. failed to malloc memory. - LOG_STD_ACTION EIO-3- NOPROC 3-Error Unable to create process. failed to create eio process. - LOG_STD_ACTION EIO-3- NOQUEUE 3-Error Unable to create queue. failed to create queue. - LOG_STD_ACTION EIO-4- EMPTY_CHUNK 4-Warning Chunk is empty. failed to malloc chunk entry due to empty chunk. - LOG_STD_ACTION EIO-4- INVALID_CDB 4-Warning Invalid eio controller cdb. encountered an invalid controller cdb. - LOG_STD_ACTION EIO-4- INVALID_SLOT 4-Warning Invalid eio slot instance. encountered an invalid eio slot instance. - LOG_STD_ACTION ELB_HA-2-GET_BUFFER 2-Critical ELB ISSU client failed to get buffer for message. Error: [dec] [chars] The ELB HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ethernet-oam "show logging and show checkpoint client" ELB_HA-2-GET_BUFFER 2-Critical ELB ISSU client failed to get buffer for message. Error: [dec] [chars] The ELB HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ethernet-oam "show logging and show checkpoint client" ELB_HA-2-INIT 2-Critical ELB ISSU client initialization failed to [chars]. Error: [dec] [chars] The ELB ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ethernet-oam LOG_STD_ACTION ELB_HA-2-INIT 2-Critical ELB ISSU client initialization failed to [chars]. Error: [dec] [chars] The ELB ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ethernet-oam LOG_STD_ACTION ELB_HA-2-SEND_NEGO_FAILED 2-Critical ELB ISSU client failed to send negotiation message. Error: [dec] [chars] The ELB ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-oam "show logging and show checkpoint client" ELB_HA-2-SEND_NEGO_FAILED 2-Critical ELB ISSU client failed to send negotiation message. Error: [dec] [chars] The ELB ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-oam "show logging and show checkpoint client" ELB_HA-2-SESSION_NEGO 2-Critical ELB ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The ELB ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-oam "show issu session and " "show issu negotiated capability " ELB_HA-2-SESSION_NEGO 2-Critical ELB ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The ELB ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-oam "show issu session and " "show issu negotiated capability " ELB_HA-2-SESSION_REGISTRY 2-Critical ELB ISSU client failed to register session information. Error: [dec] [chars] The ELB ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ethernet-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ELB_HA-2-SESSION_REGISTRY 2-Critical ELB ISSU client failed to register session information. Error: [dec] [chars] The ELB ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ethernet-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ELB_HA-3-INVALID_SESSION 3-Error ELB ISSU client does not have a valid registered session. The ELB ISSU client does not have a valid registered session. ethernet-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ELB_HA-3-INVALID_SESSION 3-Error ELB ISSU client does not have a valid registered session. The ELB ISSU client does not have a valid registered session. ethernet-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ELB_HA-3-MSG_SIZE 3-Error ELB ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The ELB ISSU client failed to calculate the MTU for the specified message. The ELB ISSU client will not able to send the message to the standby device. ethernet-oam "show issu message group and " "show issu session and " "show issu negotiated version " ELB_HA-3-MSG_SIZE 3-Error ELB ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The ELB ISSU client failed to calculate the MTU for the specified message. The ELB ISSU client will not able to send the message to the standby device. ethernet-oam "show issu message group and " "show issu session and " "show issu negotiated version " ELB_HA-3-SESSION_UNREGISTRY 3-Error ELB ISSU client failed to unregister session information. Error: [dec] [chars] The ELB ISSU client failed to unregister session information. ethernet-oam "show issu session and " "show issu negotiated capability " ELB_HA-3-SESSION_UNREGISTRY 3-Error ELB ISSU client failed to unregister session information. Error: [dec] [chars] The ELB ISSU client failed to unregister session information. ethernet-oam "show issu session and " "show issu negotiated capability " ELB_HA-3-TRANSFORM 3-Error ELB ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The ELB ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ELB state between the active device and the standby device is not identical. ethernet-oam "show issu session and " "show issu negotiated version " ELB_HA-3-TRANSFORM 3-Error ELB ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The ELB ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ELB state between the active device and the standby device is not identical. ethernet-oam "show issu session and " "show issu negotiated version " ELC_L2_ACL-3-ERRORSW 3-Error [chars] The elc l2 acl client detected software error event that is specified in the message asr1k-ether-lc LOG_STD_SH_TECH_ACTION ELC_L2_ACL-3-NOMEM 3-Error Memory Allocation Failure - [chars] : [chars]0x[hec] Memory required by l2 acl client to service one or more Network Processors could not be allocated. asr1k-ether-lc "This error may indicate that more memory must be installed on the " "affected card or platform in order to service all the features and " "related entities enabled via the configuration. " LOG_STD_SH_TECH_ACTION EM_ISSU-2-GET_BUFFER 2-Critical Event Manager ISSU client failed to get buffer for message. Error: [dec] [chars] The Event Manager ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. em "show logging and show checkpoint client" EM_ISSU-2-INIT 2-Critical Event Manager ISSU client initialization failed to [chars]. Error: [dec] [chars] The Event Manager ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. em LOG_STD_ACTION EM_ISSU-2-SEND_NEGO_FAILED 2-Critical Event Manager ISSU client failed to send negotiation message. Error: [dec] [chars] The Event Manager ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. em "show logging and show checkpoint client" EM_ISSU-2-SESSION_NEGO 2-Critical Event Manager ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Event Manager ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. em "show issu session and " "show issu negotiated capability " EM_ISSU-2-SESSION_REGISTRY 2-Critical Event Manager ISSU client failed to register session information. Error: [dec] [chars] The Event Manager ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. em "show issu capability entries and " "show issu session and " "show issu negotiated capability " EM_ISSU-3-INVALID_SESSION 3-Error Event Manager ISSU client does not have a valid registered session. The Event Manager ISSU client does not have a valid registered session. em "show issu capability entries and " "show issu session and " "show issu negotiated capability " EM_ISSU-3-MSG_NOT_OK 3-Error Event Manager ISSU client 'Message Type [dec]' is not compatible The Event Manager ISSU client received an incompatible message from the peer device. The message cannot be processed. em "show issu message group and " "show issu session and " "show issu negotiated version " EM_ISSU-3-MSG_SIZE 3-Error Event Manager ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Event Manager ISSU client failed to calculate the MTU for the specified message. The Event Manager ISSU client is not able to send the message to the standby device. em "show issu message group and " "show issu session and " "show issu negotiated version " EM_ISSU-3-OPAQUE_MSG_NOT_OK 3-Error Event Manager ISSU client 'Opaque Message Type [dec]' is not compatible The Event Manager ISSU client received an incompatible message from the peer device. The opaque message cannot be processed. em "show issu message group and " "show issu session and " "show issu negotiated version " EM_ISSU-3-SESSION_UNREGISTRY 3-Error Event Manager ISSU client failed to unregister session information. Error: [dec] [chars] The Event Manager ISSU client failed to unregister session information. em "show issu session and " "show issu negotiated capability " EM_ISSU-3-TRANSFORM_FAIL 3-Error Event Manager ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Event Manager ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Event Manager state between the active device and the standby device is not identical. em "show issu session and " "show issu negotiated version " EM-3-EXCEED 3-Error EM exceed maximum open events [dec]. The total number of open events exceeded the maximum number of possible open events. The maximum number that the EM server permits is specified in the error message. EM clients are either opening too many events or not closing events within the permitted time period. - show em state | inc EM-3-FAIL 3-Error The specified EM Function failed [chars]. The specified EM function failed. This condition might be caused by incorrect logic or a memory corruption. - "Copy the error message exactly as it appears on the console or " "in the system log. Enter the show em state " "command or the show em status command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information." EM-3-NOMEM 3-Error The EM failed to allocate memory resources for the specified\nEM \function [chars]. A timeout occurred. This condition is minor and should not affect the functionality of the switch. - "This message should not affect switch functionality but can be " "sign of a software bug condition. Please check Bug Toolkit on " "the Cisco web-site for relevant bugs against this message. If " "you do not find any please contact the TAC with the output of " "show em client" EM-3-NULLPTR 3-Error The pointer in a specified EM function [chars] is incorrectly NULL. The pointer in the specified EM function is incorrectly NULL. This condition might be caused by incorrect logic or a memory corruption. - "Copy the error message exactly as it appears on the console or " "in the system log. Enter the show em state " "command or the show em status command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information." EM-4-INVALID 4-Warning The specified EM function [chars] received Invalid operands <[dec]>. The EM client used invalid API parameters. - "Copy the error message exactly as it appears on the console or " "in the system log. Enter the show em state " "command or the show em status command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information." EM-4-LIMIT 4-Warning EM exceed open events limit [dec]. The EM has exceeded the permitted number of open events. The open event limit is 5000. - LOG_STD_ACTION EM-4-NOTUP 4-Warning The EM is not available [chars]. The specified EM function could not find the specified open event. This condition might be caused by a memory corruption. - "Copy the error message exactly as it appears on the console or " "in the system log. Enter the show em state " "command or the show em status command to " "gather data that may help Cisco technical support to identify " "the nature of the error. Contact your Cisco technical support " "representative and provide the representative with the gathered " "information." EM-4-SENDFAILED 4-Warning The specified EM client type=[dec] failed to send messages to standby. Because the specified EM client failed to send messages to the standby supervisor engine the standby supervisor engine is not updated. Do not attempt to failover to standby supervisor engine. - show checkpoint clients ENSP-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ENSP-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ENSP-2-FMAIL_INTERNAL_ERROR 2-Critical Internal software error An internal software error occurred. - LOG_STD_RECUR_ACTION ENSP-2-FMAIL_INTERNAL_ERROR 2-Critical Internal software error An internal software error occurred. - LOG_STD_RECUR_ACTION ENSP-2-FMAIL_NO_AUTH_STARTED 2-Critical AAA authentication startup failed AAA authentication startup failed - LOG_STD_RECUR_ACTION ENSP-2-FMAIL_NO_AUTH_STARTED 2-Critical AAA authentication startup failed AAA authentication startup failed - LOG_STD_RECUR_ACTION ENSP-2-INTERNAL_ERROR 2-Critical FAX- Internal software error: [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION ENSP-2-INTERNAL_ERROR 2-Critical FAX- Internal software error: [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_BAD_MESSAGE 4-Warning FAXMAIL- Bad message received An unexpected message was received. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_BAD_MESSAGE 4-Warning FAXMAIL- Bad message received An unexpected message was received. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_NO_SMTP 4-Warning FAXMAIL- Can not connect\n\to the SMTP server No connection was able to be created to any of the specified\n\SMTP servers. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_NO_SMTP 4-Warning FAXMAIL- Can not connect\n\to the SMTP server No connection was able to be created to any of the specified\n\SMTP servers. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_NO_SMTP_SEND 4-Warning FAXMAIL- Could not\n\send data to the SMTP server A connection was made to the SMTP server but no data can be sent. - LOG_STD_RECUR_ACTION ENSP-4-FMAIL_NO_SMTP_SEND 4-Warning FAXMAIL- Could not\n\send data to the SMTP server A connection was made to the SMTP server but no data can be sent. - LOG_STD_RECUR_ACTION ENSP-4-SMTP_NOT_CONNECTED 4-Warning SMTP- failed [chars] [dec] A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior. - LOG_STD_NO_ACTION ENSP-4-SMTP_NOT_CONNECTED 4-Warning SMTP- failed [chars] [dec] A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior. - LOG_STD_NO_ACTION ENSP-6-SMTP_OPEN 6-Information SMTP- opening [chars] [dec] A connection attempt ... - LOG_STD_NO_ACTION ENSP-6-SMTP_OPEN 6-Information SMTP- opening [chars] [dec] A connection attempt ... - LOG_STD_NO_ACTION ENT_API-3-NOCREAT 3-Error EntityApiProcess not created - Entity MIB will not be \n\ initialised Attempt to start EntityApiProcess failed when the entity subsystem \n\ was initialised. The Entity MIB will not be populated. snmp "The Entity MIB API process was not created possibly due to\n\ lack of memory. If you want to use the Entity MIB API \n\ reconfigure the box so that less memory is used by\n\ other features or add more memory to the system. Reload the box\n\ after reconfiguring." ENT_API-3-NOPARENTDEL 3-Error Parent physical entity [dec] did not exist when trying to delete\n\ child physical entity [dec] phyDescr = [chars] phyName = [chars]. RootIdx = [dec] An attempt to reassign parent's child pointer reference failed during\n\ the node deletion because the node's parent reference is NULL. The node\n\ and all of its sibling nodes and their childeren will be deleted. This\n\ is an unususal scenario and may happen due to any hardware malfunction\n\ such as device flapping. snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENT_API-4-MULTIPLEREG 4-Warning Multiple registration request with same entity name = [chars] \n\ using entity index [dec] and phyDescr = [chars]. An attempt to register a physical entity happened and failed \n\ because the same entity name is being used for which a registration \n\ has already been done. snmp "Need to raise a DDTS with the component responsible for the \n\ for the registration to use different entity names for registering \n\ different entities." ENT_API-4-NOALIAS 4-Warning [chars] entity not found when adding an alias with \n\ physical index = [dec] and logical index = [dec] to the Entity MIB An attempt to add an alias entry to the Entity MIB was made.\n\ The logical or physical entity with the specified index does\n\ not exist and so the alias entry creation failed. snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENT_API-4-NOENT 4-Warning Trying to add or delete an unknown entity to the Entity MIB An attempt to add/delete an unknown entity to the Entity MIB \n\ was made. The request could not be processed. snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENT_API-4-NOLPMAP 4-Warning [chars] entity not found when adding an LPMapping entry with \n\ logical index = [dec] and physical index = [dec] to the Entity MIB An attempt to add an LPMapping entry to the Entity MIB was made.\n\ The logical or physical entity with the specified index does\n\ not exist and so the LPMapping entry creation failed. snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENT_API-4-NOPARENT 4-Warning Parent physical entity [dec] did not exist when trying to add\n\ child physical entity [dec] phyDescr = [chars] phyName = [chars]. An attempt to add a physical entity failed because its\n\ parent physical entity did not exist in the entPhysicalTable\n\ of the Entity MIB. snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENT_API-4-NOPORT 4-Warning Physical entity does not have a Port PhysicalClass when \n\ adding an alias with physical index = [dec] logical index = [dec]\n\ phyDescr = [chars] phyName = [chars]\n\ phyClass = [dec] phyContainedIn = [dec] to the Entity MIB - snmp "Copy the error message exactly as it appears on the console\n\ or in the system log call your Cisco technical support\n\ representative and provide the representative with the\n\ gathered information. Using your NMS tool also provide the\n\ content of the Entity MIB table." ENTITY_ALARM-6-INFO 6-Information [chars] [chars] [chars] [chars] [chars] Alarm assertion or deassertion information. - LOG_STD_NO_ACTION ENTROPY-0-ENTROPY_ERROR 0-Emergency Unable to collect sufficient entropy On bootup the device attempts to collect entropy to initialize its random number generator. This device has failed to do so. Because of this most security protocols will not run - "This is probably a hardware failure" ENTROPY-0-ENTROPY_ERROR 0-Emergency Unable to collect sufficient entropy On bootup the device attempts to collect entropy to initialize its random number generator. This device has failed to do so. Because of this most security protocols will not run - "This is probably a hardware failure" ENTROPY-0-ENTROPY_FAILURE 0-Emergency Unable to collect sufficient entropy On bootup the router attempts to collect entropy to initialize its random number generator. This router has failed to do so. Because of this most security protocols will not run - "This is probably a hardware failure" ENTROPY-0-ENTROPY_FAILURE 0-Emergency Unable to collect sufficient entropy On bootup the router attempts to collect entropy to initialize its random number generator. This router has failed to do so. Because of this most security protocols will not run - "This is probably a hardware failure" ENTRY_MOVE_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - ENTRY_MOVE_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - ENVIRONMENT-2-FAN_FAULT 2-Critical System Fault: FAN FAULT is detected. - - - ENVIRONMENT-2-PS_A_HIGHVOLTAGE 2-Critical [chars] [chars] [chars] [chars] Power supply input voltage exceeding threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over voltage." ENVIRONMENT-2-PS_A_LOWVOLTAGE 2-Critical [chars] [chars] [chars] [chars] Power supply input voltage is below low threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by low voltage." ENVIRONMENT-2-PS_B_HIGHVOLTAGE 2-Critical [chars] [chars] [chars] [chars] Power supply input voltage exceeding threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over voltage." ENVIRONMENT-2-PS_B_LOWVOLTAGE 2-Critical [chars] [chars] [chars] [chars] Power supply input voltage is below low threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by low voltage." ENVIRONMENT-3-AC1_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 1 triggered - - ENVIRONMENT-3-AC1_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 1 triggered - - ENVIRONMENT-3-AC2_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 2 triggered - - ENVIRONMENT-3-AC2_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 2 triggered - - ENVIRONMENT-3-AC3_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 3 triggered - - ENVIRONMENT-3-AC3_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 3 triggered - - ENVIRONMENT-3-AC4_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 4 triggered - - ENVIRONMENT-3-AC4_TRIGGER 3-Error [chars] [chars] [chars] [chars] External Alarm Contact 4 triggered - - ENVIRONMENT-3-LIC_FILE_CORRUPT 3-Error [chars] [chars] [chars] [chars] License file is corrupted - - ENVIRONMENT-3-LIC_FILE_CORRUPT 3-Error [chars] [chars] [chars] [chars] License file is corrupted - - ENVIRONMENT-3-OVERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the max temperature threshold - - ENVIRONMENT-3-OVERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the max temperature threshold - - ENVIRONMENT-3-OVERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the max temperature threshold - - ENVIRONMENT-3-OVERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the max temperature threshold - - ENVIRONMENT-3-OVERVOLT 3-Error [chars] [chars] [chars] [dec] The voltage rail is above the max voltage threshold - - ENVIRONMENT-3-POWER_ERROR 3-Error [chars] Power supply error. - " Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC." ENVIRONMENT-3-POWER_ERROR 3-Error [chars] Power supply error. - " Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC." ENVIRONMENT-3-RPS_FAILED 3-Error [chars] [chars] [chars] [chars] Only one power supply was detected for system in dual power mode or\n\ power supply is failing - - ENVIRONMENT-3-RPS_FAILED 3-Error [chars] [chars] [chars] [chars] Only one power supply was detected for system in dual power mode or\n\ power supply is failing - - ENVIRONMENT-3-RPS_FAILED 3-Error [chars] [chars] [chars] [chars] Only one power supply was detected for system in dual power mode or power supply is failing - - ENVIRONMENT-3-RPS_FAILED 3-Error [chars] [chars] [chars] [chars] Only one power supply was detected for system in dual power mode or \ power supply is failing - - ENVIRONMENT-3-SD_CARD 3-Error [chars] [chars] [chars] [chars] SD card is not present - - ENVIRONMENT-3-SD_CARD 3-Error [chars] [chars] [chars] [chars] SD card is not present - - ENVIRONMENT-3-SD_CARD_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is not present. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is not present. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_CORRUPT 3-Error [chars] [chars] [chars] [chars] SD card is corrupted - - ENVIRONMENT-3-SD_CARD_CORRUPT 3-Error [chars] [chars] [chars] [chars] SD card is corrupted - - ENVIRONMENT-3-SD_CARD_CORRUPT_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is corrupted. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_CORRUPT_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is corrupted. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_FILES_CORRUPT 3-Error [chars] [chars] [chars] [chars] Image File on SD card is corrupted - - ENVIRONMENT-3-SD_CARD_FILES_CORRUPT 3-Error [chars] [chars] [chars] [chars] Image File on SD card is corrupted - - ENVIRONMENT-3-SD_CARD_FILES_CORRUPT_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] Image File on SD card is corrupted. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_FILES_CORRUPT_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] Image File on SD card is corrupted. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_UNSUPPORTED 3-Error [chars] [chars] [chars] [chars] SD card is not supported - - ENVIRONMENT-3-SD_CARD_UNSUPPORTED 3-Error [chars] [chars] [chars] [chars] SD card is not supported - - ENVIRONMENT-3-SD_CARD_UNSUPPORTED_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is not supported. Image booted from on-board flash. - - ENVIRONMENT-3-SD_CARD_UNSUPPORTED_BOOTFLASH 3-Error [chars] [chars] [chars] [chars] SD card is not supported. Image booted from on-board flash. - - ENVIRONMENT-3-UNDERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature is below the min temperature threshold - - ENVIRONMENT-3-UNDERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature is below the min temperature threshold - - ENVIRONMENT-3-UNDERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature is below the min temperature threshold - - ENVIRONMENT-3-UNDERTEMP 3-Error [chars] [chars] [chars] [chars] The chassis inside temperature is below the min temperature threshold - - ENVIRONMENT-3-UNDERVOLT 3-Error [chars] [chars] [chars] [dec] The voltage rail is below the min voltage threshold - - ENVIRONMENT-4-CONFIG_OVERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the configured threshold but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_OVERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the configured threshold\n\ but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_OVERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the configured threshold\n\ but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_OVERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature exceeds the configured threshold \ but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_OVERVOLT 4-Warning [chars] [chars] [chars] [dec] The voltage rail returns to normal range from above max voltage threshold - - ENVIRONMENT-4-SECONDARY_UNDERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature is below the configured min temperature \n\ threshold but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_UNDERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature is below the configured min temperature \n\ threshold but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_UNDERTEMP 4-Warning [chars] [chars] [chars] [chars] The chassis inside temperature is below the configured min temperature \ threshold but less or equal to the max inside temperature - - ENVIRONMENT-4-SECONDARY_UNDERVOLT 4-Warning [chars] [chars] [chars] [dec] The voltage rail returns to normal range from below low voltage threshold - - ENVIRONMENTAL-1-ALERT 1-Alert [chars] Location: [chars] State: [chars] Reading: [dec] [chars] One of the sensors in the system is reading an out of normal\n\ value. iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-1-SENSORFAIL 1-Alert [chars] Location [chars] State: fail One of the sensors in the system has detected a failure condition\n\ from which it can not recover. This sensor is no longer reporting\n\ readings to the environmental monitoring subsystem. iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-3-ALERT 3-Error Critical limit reached for PVT temperature sensor on Asic: [dec] Reading: [dec] Celsius Informational message for relating to Asic PVT sensor value asr900-system-rsp3 "No action required" ENVIRONMENTAL-3-CHASFSERR 3-Error Sensor [chars] on FRU [chars] has an invalid chasfs device state [chars] The system does not understand the state that the sensor is \n\ reporting. This is most likely a filesystem corruption or\n\ ISSU problem. You may try rebooting the router to see if the\n\ problem corrects itself. iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-3-TDLERROR 3-Error Error processing TDL message. [dec] An unexpected condition in which IOS has received a TDL\n\ message which it can not process. iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-5-SENSOROK 5-Notice [chars] Location: [chars] State: normal One of the sensors in the system had been in a failure condition\n\ but is now operating normally. iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-6-INFO 6-Information [chars] Informational message of ambient sensor reading iosxe-chassismgr LOG_STD_ACTION ENVIRONMENTAL-6-NOTICE 6-Information [chars] Location: [chars] State: [chars] Reading: [dec] [chars] Informational message on the sensor reading iosxe-chassismgr LOG_STD_ACTION ENVM-0-SHUT 0-Emergency Environmental Monitor initiated shutdown The enviromental monitor has initiated a system shutdown. - "Look at previous environmental messages to determine cause of \n\ shutdown and correct if possible. " LOG_STD_ACTION ENVM-2-ENVCRIT 2-Critical [chars] measured at [chars] One of the measured environmental test points exceeds an extreme \n\ threshold. - "Correct the specified condition or the system may shut itself down\n\ as a preventive measure.\n\ This condition could cause the system to fail to operate properly. " LOG_STD_RECUR_ACTION ENVM-3-BLOWER 3-Error [chars] may have failed One of the router's cooling fans may be close to failure. - "Replace the fan as soon as possible or the system may shut itself \n\ down or fail to operate properly." ENVM-3-LASTENV 3-Error [chars] Non volatile EEPROM storage of environmental statistics failed.\n\ This may be due to an EEPROM hardware failure. - LOG_STD_ACTION ENVM-3-NOACK 3-Error Access to [chars] failed One of the temperature sensors was not ready for \n\ the initiation of temperature environmental monitoring.\n\ Software is attempting to restart the sensor. - LOG_STD_RECUR_ACTION ENVM-3-NOFORK 3-Error Could not create environmental polling process - - "" ENVM-3-NOFORK 3-Error Could not start environment polling process The software could not spawn the enviromental monitoring\n\ process possibly because of low memory - no monitoring\n\ will be performed. - LOG_STD_REDUCE_ACTION ENVM-4-ENVWARN 4-Warning [chars] measured at [chars] One of the measured environmental test points exceeds the warning \n\ threshold. - "Closely monitor the condition and correct if possible. " LOG_STD_RECUR_ACTION ENVM-4-LONGBUSYREAD 4-Warning C2W Interface busy for long time reading temperature sensor [dec] - - "" ENVM-4-LONGBUSYWRITE 4-Warning C2W Interface busy for long time writing temperature sensor [dec] - - "" ENVM-4-READERROR 4-Warning Error reading temperature sensor [dec] - - "" ENVM-4-WRITEERROR 4-Warning Error writing temperature sensor [dec] - - "" ENVM-6-PSCHANGE 6-Information [chars] changed from [chars] to [chars] This message indicates the absence or detection\n\ of a new type of power supply in the system.\n\ This can be expected when hot-swapable power supplies are swapped.\n\ This is an informational message only. - LOG_STD_NO_ACTION ENVM-6-PSLEV 6-Information [chars] state changed from [chars] to [chars] One of the power supply test points underwent a state change. - "Closely monitor the condition and correct if possible. " LOG_STD_RECUR_ACTION ENVMON-1-CPU_CRITICAL_UNDERTEMP 1-Alert Critical Warning: CPU temperature [dec]C is below [dec]C threshold. Please resolve operating environment temperature to prevent system damage. System CPU temperature is below the threshold cgs2520 "Please save system configuration and power down system " "to prevent damage causes by operational environment or faulty components." LOG_STD_ACTION ENVMON-1-CPU_WARNING_OVERTEMP 1-Alert Warning: CPU temperature [dec]C exceeds threshold [dec]C. Please resolve system cooling immediately to prevent system damage System CPU temperature is over the threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-1-CPU_WARNING_OVERTEMP_HDD 1-Alert Warning: CPU temperature [dec]C exceeds threshold [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling immediately to prevent system damage System CPU temperature is over the threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-1-NO_PROCESS 1-Alert Failed to create environmental monitor process Failed to create environmental monitor process. cgs2520 "The amount of memory available in the router may not be sufficient. " LOG_STD_ACTION ENVMON-1-POWER_HIGH_VOLTAGE 1-Alert Critical Warning: PSU[dec] Input Voltage [dec]V exceeds high threshold [dec]V. The system may not continue operation. Immediate operator action is required. Power supply input voltage exceeding threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over voltage." LOG_STD_ACTION ENVMON-1-POWER_LOW_VOLTAGE 1-Alert Critical Warning: PSU[dec] Input Voltage [dec]V is below low threshold [dec]V. The system may not continue operation. Immediate operator action is required. Power supply input voltage is below low threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by low voltage." LOG_STD_ACTION ENVMON-1-POWER_WARNING 1-Alert : [chars] An error has occured in the power supply. cgs2520 "Make sure that the power supply is connected to input source." "Also check if the Power Supply Unit and Redundant Power Supply" "are supported by this router." "If the problem still persists then please contact TAC." ENVMON-1-RPS_ACCESS 1-Alert [chars] RPS communication error detected cgs2520 LOG_STD_ACTION ENVMON-1-RPS_FAN_FAILED 1-Alert [chars] RPS fan failure detected rps "Disconnect any routers or switches connected " "to the RPS and replace the fan immediately" ENVMON-1-RPS_OVER_CURRENT 1-Alert [chars] RPS overcurrent condition detected rps "Unplug the routers or switches that are being " "backed off" ENVMON-1-RPS_PS_MISMATCH 1-Alert [chars] Power supplies inserted in RPS are incompatible cgs2520 "Remove either one of the power supplies or " "insert compatible power supplies" ENVMON-1-RPS_THERMAL_CRITICAL 1-Alert RPS temperature has reached critical threshold The temperature sensor value inside RPS has reached the critical threshold. RPS cannot function normally rps "The external temperature is very high." " Reduce the temperature in the room immediately" ENVMON-1-RPS_WARNING 1-Alert : [chars] RPS related event notification. cgs2520 "Make sure that the correct RPS with supported FRUs is connected" " to the router. Check if RPS FRUs are connnected to the power source." "Please refer to technical document or contact TAC for" " further clarification." ENVMON-1-WARN_DOWN_REV_ROMMON 1-Alert Warning: Router's ROMMON needs to be upgraded to suppport proper operation of module [chars]. Operation [chars] without upgrading ROMMON may cause the module hard disk driver to become unstable. This router's ROMMON is down-rev and there is a module with hard disk drives installed in the system. Warn user about upgrading ROMMON. c3900 "Upgrade ROMMON" ENVMON-1-WARN_HDD_FAN_HIGH 1-Alert Warning: system temperature [dec] C is high Fan speed has reached level3 or above and there is a service module with hard disk drives installed in the system. Warn user about hard disks. c3900 "Resolve environmental alarm or shutdown the service module." ENVMON-1-WARN_HDD_HIGH_TEMP 1-Alert Critical Warning: sensor temperature [dec] C exceeds 40 C. Ambient temperature exceeds 40 C and there is a service module with hard disk drives installed in the system. Warn user about hard disks. c3900 "Cool down room temperature or increase air flow to the router." ENVMON-2-CPU_CRITICAL_OVERTEMP 2-Critical Critical: CPU temperature [dec]C exceeds [dec]C threshold. Please resolve system cooling immediately to prevent system damage. System CPU temperature is over the threshold cgs2520 "Please save system configuration and power down system " "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-CPU_CRITICAL_OVERTEMP_HDD 2-Critical Critical: CPU temperature [dec]C exceeds [dec]C threshold. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling immediately to prevent system damage. System CPU temperature is over the threshold cgs2520 "Please save system configuration and power down system " "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-FAN_TRAY_MISSING 2-Critical Critical Warning: Fan tray was removed. Please re-insert fan tray to prevent system from overheating. The environmental monitor can not detect fan tray on system chassis. cgs2520 "Make sure the fan tray is properly inserted. " "If the problem persists replacement of fan tray is necessary " ENVMON-2-IN_OUTLET_OVERTEMP 2-Critical Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system cooling to prevent system damage. Temperature sensor exceed overtemp threshold. cgs2520 "Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-IN_OUTLET_OVERTEMP_HDD 2-Critical Warning: [chars] Temperature [dec]C Exceeds [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling to prevent system damage. Temperature sensor exceed overtemp threshold. cgs2520 "Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-MODULE_OVERTEMP 2-Critical Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system heating to prevent system damage. Temperature measured by sensor exceeds high temperature threshold. cgs2520 "Please resolve system heating or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-ONBOARD_OVERTEMP 2-Critical Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system heating to prevent system damage. Temperature measured by sensor exceeds high temperature threshold. cgs2520 "Please resolve system heating or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-POWER_OVERTEMP 2-Critical Warning: [chars] temperature [dec]C exceeds threshold [dec]C. Please resolve system cooling to prevent system damage Power supply temperature exceeding threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-POWER_OVERTEMP_SHUTDOWN 2-Critical Crital Warning: [chars] temperature [dec]C exceeds threshold [dec]C. The power supply will shutdown automatically if the hight temperature condition is not resolved. Power supply temperature exceeding critial temperature threshold cgs2520 "Please save system configuration and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-2-RPS_THERMAL_WARNING 2-Critical RPS temperature has reached warning threshold The temperature sensor value inside RPS has reached the warning threshold. RPS can function normally until the temperature reaches the critical threshold rps "The external temperature is high." " Reduce the temperature in the room" ENVMON-2-SYSTEM_FAN_FAILED 2-Critical Critical Warning: System Fan has failed. Please replace the fan to prevent system overheating. System fan is not rotating. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "system fan may need to be replace." ENVMON-3-INTAKE_ABNORMTEMP 3-Error Warning: [chars] Temperature [dec]C Exceeds [dec]C. Please resolve system cooling. Temperature sensor exceed abnormal temp threshold. cgs2520 "Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-3-INTAKE_ABNORMTEMP_HDD 3-Error Warning: [chars] Temperature [dec]C Exceeds [dec]C. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please resolve system cooling. Temperature sensor exceed abnormal temp threshold. cgs2520 "Please resolve system cooling or and power down system" "to prevent damage causes by over heating." LOG_STD_ACTION ENVMON-3-POWER_ERROR 3-Error : [chars] Power supply error. cgs2520 " Make sure that the power supply connected are supported." " If the problem still persists then please contact TAC." ENVMON-3-RPS_POST_FAILED 3-Error [chars] RPS POST failure detected rps "LOG_STD_NO_ACTION" ENVMON-3-XFR_ENV_INIT_ERROR 3-Error Fails to initialize MCU Environmental Control Unit Attempt to initialize MCU Environmentcal Control Unit fails xformers LOG_STD_ACTION ENVMON-4-MULTI_FAN_LOW_RPM 4-Warning Critical Warning: More than two fans are running at low RPM. Rotation speed is now high for all other fans. Please replace fan tray to prevent system from overheating. Multiple fan failures detected. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray." ENVMON-4-MULTI_FAN_LOW_RPM_HDD 4-Warning Critical Warning: More than two fans are running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Please replace fan tray to prevent system from overheating. Multiple fan failures detected. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray." ENVMON-4-ONE_FAN_LOW_RPM 4-Warning Warning: Fan [dec] is running at low RPM. Rotation speed is now high for all other fans. Fan Tray replacement is recommended. One of the fan is not rotating. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "Pease replace system fan tray." ENVMON-4-ONE_FAN_LOW_RPM_HDD 4-Warning Warning: Fan [dec] is running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Fan Tray replacement is recommended. One of the fan is not rotating. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan power connector. If problem persists " "Pease replace system fan tray." ENVMON-4-TWO_FAN_LOW_RPM 4-Warning Warning: Two fans are running at low RPM. Rotation speed is now high for all other fans. Fan tray replacement is recommended. Two fan failures detected. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray." ENVMON-4-TWO_FAN_LOW_RPM_HDD 4-Warning Warning: Two fans are running at low RPM. Rotation speed is now high for all other fans. [chars] hard disk drive may become unusable if continuously operated at this temperature. Fan tray replacement is recommended. Two fan failures detected. cgs2520 "Make sure the fan power cable is properly attached to " "the mainboard fan tray power connector. If problem persists " "Please replace fan tray." ENVMON-5-POWER_NOTICE 5-Notice : [chars] Power supply notice. cgs2520 " This is an informational message only. No action is required." ENVMON-6-CPU_TEMP_OK 6-Information CPU temperature normal The CPU is operating at a normal temperature. cgs2520 "The CPU previously detected an over-temperature condition " "which has now cleared. This is most likely due to high ambient " "temperature where the router is located." ENVMON-6-FAN_OK 6-Information Fan [dec] is functioning normal now Previously failed fan is functioning normal now. cgs2520 "No action is required." ENVMON-6-FAN_TRAY_OK 6-Information Fan tray is detected. Fan tray previously reported as missing but it is now installed cgs2520 "This is an informational error. No action is required." ENVMON-6-IN_OUTLET_TEMP_OK 6-Information [chars] temperature normal The inlet/outlet sensor is operating at a normal temperature. cgs2520 "The in/outlet sensor previously detected an over-temperature condition " "which has now cleared. This is most likely due to high ambient " "temperature where the router is located." ENVMON-6-MODULE_TEMP_OK 6-Information [chars] temperature normal The module card is operating at a normal temperature. cgs2520 "The module card previously detected an over-temperature" "condition which has now cleared. This is most likely due to" "high ambient temperature where the router is located." ENVMON-6-ONBOARD_TEMP_OK 6-Information [chars] temperature normal The riser/ddr2/sfp sensors are operating at a normal temperature. cgs2520 "The riser/ddr2/sfp sensors previously detected an over-temperature" "condition which has now cleared. This is most likely due to" "high ambient temperature where the router is located." ENVMON-6-POWER_EXTILP 6-Information : [chars] External Inline Power supply info. c1900 " Make sure that the power supply connected is supported." " If the problem still persists then please contact TAC." ENVMON-6-POWER_TEMP_OK 6-Information [chars] temperature normal The Power Supply Unit is operating at a normal temperature. cgs2520 "The Power Supply Unit was in over-temperature level " "It is now at normal level" ENVMON-6-POWER_VOLTAGE_OK 6-Information PSU[dec] input voltage is normal The Power Supply Unit input voltage is within normal limit. cgs2520 "The Power Supply Unit input voltage was not within threshold limits " "It is now at normal level" ENVMON-6-SYSTEM_FAN_OK 6-Information Fan [dec] Functional now Sytem fan is functioning normal now. cgs2520 "No action is required." EPAMCM-0-INTERNAL_PANIC 0-Emergency [chars] A Panic Condition. - "" EPAMCM-1-INITFAIL 1-Alert msgtxt_initfail - - - EPAMCM-1-NOMEMORY 1-Alert msgtxt_nomemory - - - EPAMCM-3-INTERNAL_ERROR 3-Error [chars] Errors - "" EPAMCM-7-INTERNAL_ASSERT 7-Debug [chars]: [chars] Assertion Failure - File [chars] Line [dec] Assertion - "" EPBR_PROXY-2-EPBR_MSG_PROXYINIT_FAILURE 2-Critical EPBR - Failed to register IPC message handler result code [dec] QFP EPBR feature failed to register an IPC message handler for communication with control plane. This will cause the featue not to function. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_ALLOC_FAILURE 3-Error EPBR - Failed to get [dec] bytes space for IPC reply message QFP ET-Anallytics feature detected buffer allocation failure while sending reply to a message from another layer of EPBR feature's software stack. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_DEBUG_REG_FAILED 3-Error - EPBR Conditional Debugging Registration failed. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_INVALID_MSGLEN 3-Error EPBR - Received an invalid length IPC message QFP EPBR feature received an incorrect length of IPC message from anoter layer of EPBR feature's software stack m_enum [dec] m_subtype [dec] m_len [dec] m_flags 0x[hec] m_source [dec]. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_IPCSEND_FAIL 3-Error EPBR - Failed to send IPC message result code [dec] QFP EPBR feature failed to send IPC message to another layer of EPBR feature's software stack. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_OPENREPLY_FAIL 3-Error EPBR - Failed to open reply message part of IPC packet QFP EPBR feature failed to open message part of IPC packet while sending a reply to another layer of EPBR feature's software stack. EPBR_COMP_NAME LOG_STD_ACTION EPBR_PROXY-3-EPBR_MSG_PROXY_UNKNOWN_IPCMSG 3-Error EPBR - Received an unknown type code [dec] IPC message QFP EPBR feature received an unknown message from another layer of EPBR feature's software stack. EPBR_COMP_NAME LOG_STD_RECUR_ACTION EPBR_PROXY-4-PROXY_IPC_INVALID_MSG_LEN 4-Warning [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid EPBR IPC message length. cpp-ucode LOG_STD_ACTION EPC-3-MEM_INIT_FAILED 3-Error Allocation of [chars] memory failed for EPC EPC Initialization of channel pool failed. cpp-ucode LOG_STD_ACTION EPC-3-PKT_REPLICA_INIT_FAILED 3-Error Register to Generic Packet Replication failed for EPC EPC Initialization of packet replication registration failed. cpp-ucode LOG_STD_ACTION EPIF_PORT-0-INTERNAL_PANIC 0-Emergency [chars] A Panic Condition. - "" EPIF_PORT-1-INITFAIL 1-Alert msgtxt_initfail - - - EPIF_PORT-1-INTERNAL_ALERT 1-Alert [chars] A condition that should be corrected immediately. - "" EPIF_PORT-1-NOMEMORY 1-Alert msgtxt_nomemory - - - EPIF_PORT-2-INTERNAL_CRITICAL 2-Critical [chars] Critical Conditions - "" EPIF_PORT-3-INTERNAL_ERROR 3-Error [chars] Errors - "" EPIF_PORT-4-INTERNAL_INTERFACE_WARNING 4-Warning Interface [chars] [chars] Per interface Warning - "" EPIF_PORT-4-INTERNAL_WARNING 4-Warning [chars] Warning - "" EPIF_PORT-6-INTERNAL_EVENT 6-Information [chars] Informational - "" EPIF_PORT-7-INTERNAL_ASSERT 7-Debug [chars]: [chars] Assertion Failure - File [chars] Line [dec] Assertion - "" EPM-3-SEND_MSG_FAILURE 3-Error Process send msg failure for session hdl [hec] [chars] This message indicates a process send msg failure eedge-epm "No action required" EPM-3-SEND_MSG_FAILURE 3-Error Process send msg failure for session hdl [hec] [chars] This message indicates a process send msg failure eedge-epm "No action required" EPM-4-POLICY_APP_FAILURE 4-Warning Policy Application Failed for Client [[chars]] MAC [[enet]] AuditSessionID [[chars]] for POLICY_TYPE [chars] POLICY_NAME [chars] REASON [chars] This message indicates that the displayed policy for the client\n\ could not be applied by the EPM pem "Policy application failure could happen due to multiple reasons.The \n\ reason for the failure is notified to the client and the client has to\n\ take appropriate action based on it" EPM-4-POLICY_APP_FAILURE 4-Warning Policy Application Failed for Client [[chars]] MAC [[enet]] AuditSessionID [[chars]] for POLICY_TYPE [chars] POLICY_NAME [chars] REASON [chars] This message indicates that the displayed policy for the client\n\ could not be applied by the EPM pem "Policy application failure could happen due to multiple reasons.The \n\ reason for the failure is notified to the client and the client has to\n\ take appropriate action based on it" EPM-6-AAA 6-Information POLICY [chars]| EVENT [chars] This message indicates a download request has been sent/downloaded\n\ successfully for the specified dACL pem "No action required" EPM-6-AAA 6-Information POLICY [chars]| EVENT [chars] This message indicates a download request has been sent/downloaded\n\ successfully for the specified dACL pem "No action required" EPM-6-ACL_CONFIG_ERROR 6-Information ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]' This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration pem "Change ACE configuration for the specifed ACL" EPM-6-ACL_CONFIG_ERROR 6-Information ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]' This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration pem "Change ACE configuration for the specifed ACL" EPM-6-ACL_CONFIG_ERROR 6-Information ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]' This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration pem "Change ACE configuration for the specifed ACL" EPM-6-ACL_CONFIG_ERROR 6-Information ACL NAME '[chars]' | ACE SEQUENCE %ld | RESULT FAILURE | REASON '[chars]' This message indicates that adding an ACE to the specified ACL\n\ was ignored because of wrong configuration pem "Change ACE configuration for the specifed ACL" EPM-6-AUTH_ACL 6-Information POLICY [chars]| EVENT [chars] This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed pem "No action required" EPM-6-AUTH_ACL 6-Information POLICY [chars]| EVENT [chars] This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed pem "No action required" EPM-6-AUTH_ACL 6-Information POLICY [chars]| EVENT [chars] This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed pem "No action required" EPM-6-AUTH_ACL 6-Information POLICY [chars]| EVENT [chars] This message indicates a AUTH_DEF_ACL or AUTH_DEF_ACL_OPEN has been \n\ applied or removed pem "No action required" EPM-6-IPEVENT 6-Information IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars] This message indicates the IP event Wait/Release/Assignment that\n\ has occured with respect to the specified host pem "No action required" EPM-6-IPEVENT 6-Information IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars] This message indicates the IP event Wait/Release/Assignment that\n\ has occured with respect to the specified host pem "No action required" EPM-6-POLICY_APP_SUCCESS 6-Information Policy Application succeded for Client [[chars]] MAC [[enet]] AuditSession ID [[chars]] for POLICY_TYPE [[chars]] POLICY_NAME [[chars]] This message indicates that the displayed policy for the client has been\n\ applied successfully by the EPM pem "No action required" EPM-6-POLICY_APP_SUCCESS 6-Information Policy Application succeded for Client [[chars]] MAC [[enet]] AuditSession ID [[chars]] for POLICY_TYPE [[chars]] POLICY_NAME [[chars]] This message indicates that the displayed policy for the client has been\n\ applied successfully by the EPM pem "No action required" EPM-6-POLICY_REQ 6-Information IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars] This message indicates that a policy application/remove request has been\n\ received by the EPM pem "No action required" EPM-6-POLICY_REQ 6-Information IP [chars]| MAC [enet]| AuditSessionID [chars]| EVENT [chars] This message indicates that a policy application/remove request has been\n\ received by the EPM pem "No action required" EQPT_ALARM_PERSISTENCY-3-EQPT_ALARM_INFO_NULL 3-Error Persistent alarm queue alarm info is NULL - - - EQPT_ALARM_PERSISTENCY-3-EQPT_ALARM_QUEUE_NULL 3-Error Persistent alarm queue info is NULL - - - EQPT_ALARM_PERSISTENCY-3-EQPT_NULL_DATA_STRUCTURE 3-Error [chars] is NULL - - - ERP_G8032-3-APS_CHANNEL_INACTIVE 3-Error No longer receiving R-APS messages for ethernet ring [chars] instance [dec] A ring node has not received R-APS messages on the APS channel for an extended period of time. A properly functioning ring will have an R-APS message transmitted nominally every 5 seconds. This indicates that the requesting transmitting remote node on the ring such as ethernet-g8032 "Confirm the remote node is transmitting R-APS " "messages and that there is network connectivity on " "the APS channel between the remote node and this " "node." ERP_G8032-3-APS_CHANNEL_INACTIVE 3-Error No longer receiving R-APS messages for ethernet ring [chars] instance [dec] A ring node has not received R-APS messages on the APS channel for an extended period of time. A properly functioning ring will have an R-APS message transmitted nominally every 5 seconds. This indicates that the requesting transmitting remote node on the ring such as ethernet-g8032 "Confirm the remote node is transmitting R-APS " "messages and that there is network connectivity on " "the APS channel between the remote node and this " "node." ERP_G8032-3-PORT_STATE_REQ_ACK_FAILED 3-Error Port state negative ACK received for port [chars] state [dec] A port state change request was sent to the hardware successfully but a negative acknowledgement was received for this request. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-3-PORT_STATE_REQ_ACK_FAILED 3-Error Port state negative ACK received for port [chars] state [dec] A port state change request was sent to the hardware successfully but a negative acknowledgement was received for this request. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-3-PORT_STATE_REQ_ACK_TIMER_EXPIRED 3-Error No port state ACK received for ring [chars] instance [dec] port [dec] state [dec] A port state change request was sent to the hardware successfully but an acknowledgement was never received for this request. This means that there is a problem in the hardware. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-3-PORT_STATE_REQ_ACK_TIMER_EXPIRED 3-Error No port state ACK received for ring [chars] instance [dec] port [dec] state [dec] A port state change request was sent to the hardware successfully but an acknowledgement was never received for this request. This means that there is a problem in the hardware. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-3-PORT_STATE_REQ_MAX_LIMIT 3-Error Port state request has been sent many times and the desired state has not been achieved for port [chars] A port state change request was sent to the hardware successfully and acknowledgement was received but the desired state was not achieved. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-3-PORT_STATE_REQ_MAX_LIMIT 3-Error Port state request has been sent many times and the desired state has not been achieved for port [chars] A port state change request was sent to the hardware successfully and acknowledgement was received but the desired state was not achieved. ethernet-g8032 "This error message likely indicates an internal IOS " "software issue. Try shutting and then bringing up " "the port. If this continues reboot the device. " "If the previous instructions didn't work use the " "Cisco software defect search tool to " "determine if this issue has been " "fixed in a later software release. If no defect is " "found then please contact your Cisco technical " "support representative and provide the " "representative with the exact error message seen " "as well as the version of IOS being used." ERP_G8032-4-FOP_PM_LOWER_LEVEL 4-Warning Node received an R-APS message with Node Id [chars] level [dec] which is lower than configured level [dec] for Ethernet ring [chars] instance [dec] A ring node detects an R-APS message with a lower level than the configured G.8032 instance level for that APS Channel. This is a Failure of Protocol - Provisioning Mismatch - Level due to a misconfiguration of the APS level of nodes in the ring. ethernet-g8032 "Identify the other node with Node Id and " "reconfigure it with a matching APS level." ERP_G8032-4-FOP_PM_LOWER_LEVEL 4-Warning Node received an R-APS message with Node Id [chars] level [dec] which is lower than configured level [dec] for Ethernet ring [chars] instance [dec] A ring node detects an R-APS message with a lower level than the configured G.8032 instance level for that APS Channel. This is a Failure of Protocol - Provisioning Mismatch - Level due to a misconfiguration of the APS level of nodes in the ring. ethernet-g8032 "Identify the other node with Node Id and " "reconfigure it with a matching APS level." ERP_G8032-4-FOP_PM_MULTIPLE_RPL_OWNER 4-Warning RPL Owner node received an R-APSNRRB message from another RPL RPL Owner node detects a No Request R-APS message with the RPL Blocked status flag set and the Node Id differs from its own. This is a Failure of Protocol - Provision Mismatch due to a misconfiguration where there are multiple RPL Owner nodes configured in the ring. ethernet-g8032 "Identify the other RPL Owner node with Node Id and " "reconfigure it to be a non-RPL Owner node." ERP_G8032-4-FOP_PM_MULTIPLE_RPL_OWNER 4-Warning RPL Owner node received an R-APSNRRB message from another RPL RPL Owner node detects a No Request R-APS message with the RPL Blocked status flag set and the Node Id differs from its own. This is a Failure of Protocol - Provision Mismatch due to a misconfiguration where there are multiple RPL Owner nodes configured in the ring. ethernet-g8032 "Identify the other RPL Owner node with Node Id and " "reconfigure it to be a non-RPL Owner node." ERP_G8032-6-CLEAR_REMINDER 6-Information Non-revertive ethernet ring [chars] instance [dec] is ready to be cleared by user Faults have disappeared from a non-revertive ethernet ring instance so now it is ready to be cleared by the user. A non-revertive ring instance by definition requires user action because it does not revert automatically. The act of clearing the ring will cause the location of the block to move to the RPL link and the state to transition to Idle. ethernet-g8032 "Once ready to move the block to the RPL link the " "ring instance can be cleared with the " "ethernet ring g8032 clear " "command." ERP_G8032-6-CLEAR_REMINDER 6-Information Non-revertive ethernet ring [chars] instance [dec] is ready to be cleared by user Faults have disappeared from a non-revertive ethernet ring instance so now it is ready to be cleared by the user. A non-revertive ring instance by definition requires user action because it does not revert automatically. The act of clearing the ring will cause the location of the block to move to the RPL link and the state to transition to Idle. ethernet-g8032 "Once ready to move the block to the RPL link the " "ring instance can be cleared with the " "ethernet ring g8032 clear " "command." ERP_G8032-6-STATE_CHANGED 6-Information Ethernet ring [chars] instance [dec] changed state to [chars] Informational message to notify the state transitions for a ring instance ethernet-g8032 "None. This is an informational message to indicate " "an event may have triggered some ring protection " "action." ERP_G8032-6-STATE_CHANGED 6-Information Ethernet ring [chars] instance [dec] changed state to [chars] Informational message to notify the state transitions for a ring instance ethernet-g8032 "None. This is an informational message to indicate " "an event may have triggered some ring protection " "action." ERROR-3-OF_AGENT 3-Error ERRMSG_NOFLAGS - - - ERROR-3-OF_AGENT 3-Error ERRMSG_NOFLAGS - - - ERROR-3-OVS 3-Error ERRMSG_NOFLAGS - - - ERROR-3-OVS 3-Error ERRMSG_NOFLAGS - - - Error in handling FRR: [chars] [chars] [hec] [hec] Error in FRR processing c7600-sip-common "This is a internal software error. If this " "error happened while configuring FRR try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION - - ERSPAN-3-MEM_INIT_FAILED 3-Error Allocation of [chars] memory failed for ERSPAN ERSPAN Initialization of channel pool failed. cpp-ucode LOG_STD_ACTION ERSPAN-3-PKT_REPLICA_INIT_FAILED 3-Error Register to Generic Packet Replication failed for ERSPAN ERSPAN Initialization of packet replication registration failed. cpp-ucode LOG_STD_ACTION ESF_MPLS-3-EREVENT 3-Error [chars] An internal software error occurred. firmware LOG_STD_ACTION ESF_MPLS-3-ESF_FIB_ADD_FAILED 3-Error Attempt to add ESF tagged route [inet]/[dec] Table %lu failed An internal software error occurred. firmware LOG_STD_ACTION ESG_MEMORY_UPGRADE-3-CONF_FAILED 3-Error Configuration of memory failed. An error occurred when memory configuration was attempted. iosxe-csl - ESS_FEATURE-3-ESF_STUB 3-Error CPP ESS per-session feature [chars] executes stub entry in [chars] direction Cisco internal software error. CPP ESS per-session feature stub entry got executed. The packet will be dropped. qfp-bb keyword:none LOG_STD_ACTION ESS_FEATURE-4-ESF_DROP_POLICY 4-Warning CPP ESS feature encounted unexpected linktype=[dec] Cisco internal software error. CPP ESS per-session feature encounted unexpected linktype when executing output drop policy qfp-bb keyword:none LOG_STD_ACTION ESS_IPSUB-3-ESS_IPSUB_STUB 3-Error CPP ESS IPSUB executes stub entry in [chars] direction Cisco internal software error. CPP ESS IPSUB stub entry got executed. The packet will be dropped. qfp-bb keyword:none LOG_STD_ACTION ESS_IPSUB-3-FSOL_THROTTLE_ERR 3-Error Allocation of [chars] memory failed for ESS IP Subscriber Allocation of memory resource demanded by ESS IPSUB FSOL throttle failed. This is a serious problem at the ESS IPSUB FSOL initialization for throttling. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-IPC_THROTTLE_ERR 2-Critical Allocation of [chars] memory failed for ESS Proxy unsolicited event throttling Allocation of memory resource demanded by ESS Proxy throttle failed. This is a serious problem at the ESS Proxy IPC initialization for unsolicited event throttling. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-KA_CHANNEL_ALLOC_FAILED 2-Critical CPP ESS Proxy Session Keepalive channel creation failure. Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the channel creation failed. CPP ESS proxy session keepalive will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-KA_PKT_REPLICA_REG_FAILED 2-Critical CPP ESS Proxy Session Keepalive packet replication registration failure result: [dec]. Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the packet replication registration failed. CPP ESS proxy session keepalive will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-KA_PKT_TMPL_BFR_ALLOC_FAILED 2-Critical CPP ESS Proxy Session Keepalive packet template allocation failure [chars] buffer length: [dec]. Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the packet template buffer allocation failed. CPP ESS proxy session keepalive will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-KA_TIMER_INIT_FAILED 2-Critical CPP ESS Proxy Session Keepalive timer initialization failure. Cisco internal software error. CPP ESS Proxy Session Keepalive detected that the timer initialization failed. CPP ESS proxy session keepalive will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical CPP ESS Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. CPP ESS Proxy initialization detected that the IPC interface initialization failed. CPP ESS proxy will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-3-PROXY_BAD_MSG 3-Error CPP ESS Proxy received bad length message type [dec] Cisco internal software error. CPP ESS Proxy received a corrupted message from control plane. This message will be ignored. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-3-PROXY_INV_MSG 3-Error CPP ESS Proxy received invalid message type [dec] Cisco internal software error. CPP ESS Proxy received an invalid message type from control plane. This message will be ignored. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error CPP ESS Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. CPP ESS Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-3-PROXY_IPC_NO_HDLR 3-Error CPP ESS Proxy received unregistered message type [dec] Cisco internal software error. CPP ESS Proxy received a message from control plane but there is no registered handler. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ESS_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error CPP ESS Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. CPP ESS Proxy message processing detected a message sent failure. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ESS_SWITCH-3-ESS_STUB 3-Error CPP ESS switching [chars] feature executes stub entry in [chars] direction Cisco internal software error. CPP ESS Switching feature stub entry got executed. The packet will be dropped. qfp-bb keyword:none LOG_STD_ACTION ESS_SWITCH-3-STATS_INVALID_PTR 3-Error CPP ESS Switching invalid statistics block for session [chars]. Cisco internal software error. CPP ESS Switching session contains an invalid statistics block. The session statistics is lost. qfp-bb keyword:none LOG_STD_ACTION ETC-3-NULL_AG_UNKNOWN_GROUP 3-Error The system does not find port-channel group information The system is trying to retrieve the port-channel group information for a specific port channel but it cannot find it. PF_DDTS_COMPONENT LOG_STD_ACTION ETC-4-NOMEM 4-Warning Not enough memory available for [chars] The PAgP/LACP Shim/EC could not obtain the memory it needed. fec LOG_STD_SH_TECH_ACTION ETC-5-BUNDLE 5-Notice Interface [chars] joined port-channel [chars] Interface joined the bundle. - - ETC-5-CANNOT_ALLOCATE_AGGREGATOR 5-Notice Aggregator limit reached cannot allocate aggregator for group [dec] New aggregator cannot be allocated in the group. Change the port attributes of the ports in the group so that they match and join the same aggregator. - - ETC-5-CANNOT_BUNDLE_LACP 5-Notice [chars] is not compatible with aggregators in channel [dec] and cannot attach to them [chars] The port has different port-attributes that of port-channel or ports within the port-channel. For the port to join the bundle change the ports attributes so that it matches the port. - "Match the port-attributes to that of port-channel" ETC-5-CANNOT_BUNDLE_QOS 5-Notice Removed [chars] from port channel because a QoS policy cannot be supported across multiple DFC cards. The Port specified in the error message cannot join port channel because the QoS policy attached to the port channel cannot support multiple DFC cards. fec "Place the port in another port channel or remove " "the QoS policy from the port channel." ETC-5-CANNOT_BUNDLE_QOS1 5-Notice Removed [chars] from port channel as QoS attributes of port and port-channel are different. The Port specified in the error message cannot join port channel because the QoS attributes of this port are not consistent with the QoS attributes of the port-channel. fec "Match the QoS attributes of the specified port to the QoS " "attributes of other member ports in the port channel. Use the " "show queueing interface command to display " "the QoS attributes of a port." ETC-5-CANNOT_BUNDLE1 5-Notice Port-channel [chars] is down port [chars] will remain stand-alone. The state of the aggregation port is down. The port will remain\n\ stand-alone until the state of the aggregation port is up. - "Ensure that the other ports in the bundle have the\n\ same configuration." ETC-5-CANNOT_BUNDLE2 5-Notice [chars] is not compatible with [chars] and will be suspended [chars] The attributes of the specified port are different from the attributes of the port-channel or the attributes of the ports within the port-channel. - "Match the attributes of the specifed port to the attributes of the " "port-channel so that the specified port can join the bundle". ETC-5-COMPATIBLE 5-Notice [chars] is compatible with port-channel members The specified port was not operational earlier because its attributes were different from the attributes of the port-channel or the attributes of the ports within the port-channel. The system detects that the attributes of the specified port now match the port-channel attributes. - LOG_STD_NO_ACTION ETC-5-DONTBNDL 5-Notice [chars] suspended: incompatible remote port with [chars] The configuration of the remote port is different from the configuration of other remote ports in the bundle. A port can only join the bundle when the configuration of the local port and the configuration of the remote port are the same as other ports already in the bundle. fec "Ensure that the configuration of the remote ports " "is the same for all ports in the bundle" ETC-5-ERRPROT 5-Notice Channel protocol mismatch for interface [chars] in group [dec]: the interface can not be added to the channel group The interface can not be added to the channel-group with the specified mode fec "Change the channel-group or the mode for the " "interface" ETC-5-ERRPROT2 5-Notice Command rejected: the interface [chars] is already part of a channel with a different type of protocol enabled The interface can not be selected for the specified protocol since is already part of a channel with a different type of protocol enabled fec "Remove the interface from the channel group" ETC-5-ERRPROT3 5-Notice Command rejected: the interface [chars] is already part of a channel The interface can not be unselected for the specified protocol since is already part of a channel fec "Remove the interface from the channel group" ETC-5-L3DONTBNDL1 5-Notice [chars] suspended: PAgP not enabled on the remote port. PAgP is enabled on an L3 interface but it has been detected that the remote port does not have PAgP enabled. In this mode the port is put in a suspended state. fec "Enable PAgP on remote side" ETC-5-L3DONTBNDL2 5-Notice [chars] suspended: LACP currently not enabled on the remote port. LACP is enabled on an L3 interface but it has been detected that the remote port does not have LACP enabled. In this mode the port is put in a suspended state. fec "Enable LACP on the remote side" ETC-5-MINLINKS_MET 5-Notice Port-channel [chars] is up as its bundled ports [dec] meets min-links The administrative configuration of minimum links is equal or less than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ up fec "This is an informational message only.\n\ No action is required" ETC-5-MINLINKS_NOTMET 5-Notice Port-channel [chars] is down bundled ports [dec] doesn't meet min-links The administrative configuration of minimum links is greater than the\n\ number of bundled ports. Therefore this port channel has been brought\n\ down fec "Reduce the min-links configuration for this group\n\ or add more ports to this port-channel to create a\n\ bundle." ETC-5-NOLACP 5-Notice Invalid EC mode LACP not enabled LACP is not included in the image. Cannot set EC mode to active/passive fec "Get an image with LACP included or set mode to On" ETC-5-NOPAGP 5-Notice Invalid EC mode PAgP not enabled PAgP is not included in the image. Cannot set EC mode to desirable/auto fec "Get an image with PAgP included or set mode to On" ETC-5-PORTDOWN 5-Notice Shutting down [chars] as its port-channel is admin-down The administrative state of the port is controlled by the administrative state of its aggregate port. If the administrative state of the aggregate port is down the administrative state of the port will also be forced to be down fec "Enter the no shutdown command " "on the aggregate port to activate unshut the " ETC-5-STAYDOWN 5-Notice [chars] will remain down as its port-channel [chars] is admin-down The administrative state of the aggregation port overrides that of the port. If the aggregation port is administratively down all ports in the aggregation port will also be forced to be administratively down. fec "Enter the no shutdown command " "on the aggregation port to activate unshut the " ETC-5-UNBUNDLE 5-Notice Interface [chars] left the port-channel [chars] Interface fell off the bundle - - ETC-5-UNSUITABLE 5-Notice [chars] will not join any port-channel [chars] Configuring any of Port-fast VMPS Dest-SPAN are considered unsuitable for etherchannel. Please unconfigure them. - - ETH_SPA_GEN-3-CU_SFP_NOT_SUPP 3-Error CU-SFP is not supported on SPA-2x1GE-V2 / SPA-2x1GE-SYNCE CU-SFP is not supported on SPA-2x1GE-V2 / SPA-2x1GE-SYNCE spa-eth-all "Use PHY based ports for CU Connections " ETH_SPA_GEN-3-UNSUPPORTED_XCVR 3-Error Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2 Transceiver type GLC-GE-100FX is not supported on SPA-8xGE-V2 spa-eth-all "Consult the documentation and ensure supported " "transceivers are plugged into the SPA" ETH_SPA_GILA_FUGU-3-DATA_VER_MISMATCH 3-Error TCAM checkpointed data version [dec] differs from current version [dec]. During Minimal Disruptive Restart version of checkpointed tcam data is found to be different from the data in the current version. The SPA will be reset as normal and hence will impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-ELT_NOT_IN_CUR_VER 3-Error The element at address [dec] in [chars] tcam is found missing during Minimal Disruptive Restart reconcilation. During the reconcilation phase of Minimumal Disruptive Restart an element was found to be present in the old IOS but not present in the new IOS image. This indicates that the config for this element was not played down from the RP during config-replay. This is an error condition and the SPA will be reset as normal and hence will impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance" ETH_SPA_GILA_FUGU-3-HDR_PARAMS_MISMATCH 3-Error TCAM checkpointed header values differs from values in current version. During Minimal Disruptive Restart values of fields in the checkpointed tcam header is found to be differnt from the values in the current version of IOS. The SPA will be reset as normal and hence will impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-HDR_VER_MISMATCH 3-Error TCAM checkpointed header version [dec] differs from current version [dec]. During Minimal Disruptive Restart version of checkpointed tcam header is found to be different from the header in the current version. The SPA will be reset as normal and hence will impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-HW_SW_MISMATCH 3-Error The hardware and software copies of the element at address [dec] in tcam [chars] do not match. This indicates reconcilation failure. During reconcilation phase of Minimal Disruptive Restart it is found that the software and hardware copies of an element in tcam do not match. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance" ETH_SPA_GILA_FUGU-3-RECONFIG_FAILURE 3-Error Fugu reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart fugu reconfiguration error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-RESTART_FAILURE 3-Error Fugu restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart fugu restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-SPI4_MCALPRTY_ERR 3-Error [chars] : [chars] Calender memory Parity error An internal SPI4 error SPI4 calender memory parity error occurred spa-eth-all "If the issue persists it may be a case of bad hardware. Please open " "a case with Cisco technical support personnel for further assistance." ETH_SPA_GILA_FUGU-3-SPI4_MCALRBPRTY_ERR 3-Error [chars] : [chars] Calender memory read back Parity error An internal SPI4 error SPI4 Calender memory read back parity error spa-eth-all "Try reseating the SPA and if the issue persists open a case with the " "Cisco Technical Assistance Center." ETH_SPA_GILA_FUGU-3-SPI4_MCNTPRTY_ERR 3-Error [chars] : [chars] Memory Parity error An internal SPI4 error SPI4 Control FIFO Memory Parity error spa-eth-all "If the issue persists open a case with Cisco Technical Assistance " "Center for further assistance." ETH_SPA_GILA_FUGU-3-SPI4_MDATAPRTY_ERR 3-Error [chars] : [chars] Memory Parity error An internal SPI4 error SPI4 DATA FIFO Memory Parity error spa-eth-all "If the issue persists open a case with Cisco Technical Assistance " "Center for further assistance." ETH_SPA_GILA_FUGU-3-SPI4_OVF_ERR 3-Error [chars] : [chars] Overflow Error An internal SPI4 error SPI4 Overflow Error occured in the SPA. spa-eth-all "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-SPI4_RDOOF_ERR 3-Error [chars] : [chars] Rdata Out of Frame error An internal SPI4 error SPI4 Rdata Out of Frame error occured in spa-eth-all "If the issue persists open a case with the Cisco Technical Assistance " "Center." ETH_SPA_GILA_FUGU-3-SPI4_SYNC_FAIL 3-Error [chars] : Sync check failed in [chars] SPI4 interafce Synchronization check failed in the Gila/Fugu SPI4 interafce spa-eth-all "Try reseating the SPA. If the issue persists contact Cisco Technical " "Assistance Center." ETH_SPA_GILA_FUGU-3-TCAM_RECONFIG_FAILURE 3-Error Fugu TCAM reconfiguration failed for SPA in slot [dec] bay [dec] with error [dec] reconfig_needed [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart fugu tcam reconfiguration error has occure. This indicates an error and SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-TCAM_RESTART_FAILURE 3-Error TCAM restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart fugu tcam restart has failed. This indicates an error and SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_GILA_FUGU-3-VLAN_TCAM_ERR 3-Error TCAM programming error at offset [dec] An error was encountered when programming the VLAN TCAM. Two tcam entries are seen to have the same logical address so traffic drop will be seen on these subinterfaces spa-eth-all "Reload the Linecard. If the issue persists please " "open a case with Cisco TAC for further assistance." ETH_SPA_GILA_FUGU-6-ELT_IS_NEW 6-Information The element at address [dec] in [chars] tcam is found to be new during Minimal Disruptive Restart reconcilation. During the reconcilation phase of Minimumal Disruptive Restart an element was found to be present in the new IOS but not present in the old IOS image. This is not an error condition the SPA driver will program this new entry into the hardware. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance" ETH_SPA_MAC-3-INTR_MAX_BURST 3-Error Bursts of interrupts from [chars] have crossed maximum limit [dec] for port [dec]/[dec]/[dec] Burst of interrupts that have crossed the maximum limit are detected by the SPA. spa-eth-all "Check the interface configuration and receive signal characteristics. " "Also verify the XFP transceiver and receive signal path. " "Re-enable the interface after corrective action." ETH_SPA_MAC-3-PHY_RECONFIG_FAILURE 3-Error PHY reconfiguration failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. This indicates an error and the SPA will be reset as normal and impact traffic. - spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_MAC-3-PHY_RESTART_FAILURE 3-Error PHY restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart phy restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_MAC-3-RECONFIG_FAILURE 3-Error MAC reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart a mac reconfiguration error has occured.This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_MAC-3-RESTART_FAILURE 3-Error MAC restart failed for SPA in slot [dec] bay [dec] with error [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart mac restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_MAC-3-SPI4_ERROR 3-Error [chars] : SPI4 Error occured in the MAC SPI4 error occured in the MAC. spa-eth-all "SPI error reported in the SPA. Try reseating the SPA if the error " "occurs multiple times. If you further need assistance please open a " "case with Cisco TAC at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl" ETH_SPA_MAC-3-SPI4_SINK_INIT_ERR 3-Error [chars] : Marvel spi4.1 sink init failed PL410 global status not set An internal SPI4 error occurred in the SPA. spa-eth-all "If the issue persists return the SPA using the RMA process." ETH_SPA_MAC-3-UNREC_ECC_ERR 3-Error [chars] : An unrecoverable ECC error occured in the MAC An unrecoverable ECC error occured in the MAC. spa-eth-all "Try to reload the SPA to recover from the failure. If the problem " "persist contact Cisco Technical Assistance Center for assistance." ETH_SPA_MAC-6-INTR_BURST 6-Information Interrupts from [chars] have crossed burst limit of [dec] in [dec] msec for port [dec]/[dec]/[dec] Interrupts that have crossed the burst limit are detected by the SPA. spa-eth-all "Check the interface configuration and receive signal characteristics. " "Also verify the XFP transceiver and receive signal path. " "Re-enable the interface after corrective action." ETH_SPA_SERDES-3-RECONFIG_FAILURE 3-Error Serdes reconfiguration failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart serdes reconfiguration error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETH_SPA_SERDES-3-RESTART_FAILURE 3-Error Serdes restart failed for SPA in slot [dec] bay [dec] during Minimal Disruptive Restart. During Minimal Disruptive Restart serdes restart error has occured. This indicates an error and the SPA will be reset as normal and impact traffic. spa-eth-v2 "Open a case with Cisco Technical Assistance Center for further " "assistance." ETHCNTR-2-MOLSENDTIMEOUT 2-Critical Molecule send timeout queue [dec] molecule 0x[hec] 0x[hec] An attempt to read or write one or more of the hardware settings failed. firmware LOG_STD_ACTION ETHCNTR-3-FLOWCONTROL_DUPLEX_ERROR 3-Error Flowcontrol will not take effect until duplex is set to auto. - firmware "Configure duplex auto" ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD 3-Error Half-duplex loopback detected collision threshold exceeded on [chars]. The collisions on a half-duplex port exceeded the threshold with no valid data packets. The port is considered to be in a loopback condition. This may be caused by accidentally plugging a balun cable into the port firmware "Correct the problem causing the " "loopback condition. Then bring the port up by entering " "the shutdown then no shutdown interface configuration " "commands. The port will be automatically restarted " "after a timeout if errdisable recovery cause loopback " "is configured." ETHCNTR-3-HALF_DUX_COLLISION_EXCEED_THRESHOLD 3-Error Half-duplex loopback detected collision threshold exceeded on [chars]. The collisions on a half-duplex port exceeded the threshold with no valid data packets. The port is considered to be in a loopback condition. This may be caused by accidentally plugging a balun cable into the port firmware "Correct the problem causing the loopback condition. Then " "bring the port up by entering the shutdown then no shutdown " "interface configuration commands. The port will be " "automatically restarted after a timeout if errdisable " "recovery cause loopback is configured." ETHCNTR-3-INTERNAL_ERROR 3-Error Internal Error [chars] An internal error occurred. firmware LOG_STD_RECUR_ACTION ETHCNTR-3-INVALIDMAP 3-Error Invalid map [dec] for address [enet] An attempt to bridge a packet in software obtained an invalid result. firmware LOG_STD_RECUR_ACTION ETHCNTR-3-LOOP_BACK_DETECTED 3-Error Keepalive packet loop-back detected on [chars]. Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network. firmware "Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands. The port " "will be automatically restarted after a timeout if errdisable " "recovery cause loopback is configured." ETHCNTR-3-LOOP_BACK_DETECTED 3-Error Keepalive packet loop-back detected on [chars]. Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network. firmware "Correct the problem causing the loopback condition. Then " "bring the port up by entering the shutdown then no shutdown " "interface configuration commands. The port will be " "automatically restarted after a timeout if errdisable " "recovery cause loopback is configured." ETHCNTR-3-MOLSENDINT 3-Error Molecule send from interrupt handler An interrupt handler is accessing the hardware in a manner that is not permissible in an interrupt handler. firmware LOG_STD_ACTION ETHCNTR-3-RA_ALLOC_ERROR 3-Error RAM Access [chars] [chars] memory allocation failure A request to read/write RAM failed memory allocation firmware LOG_STD_RECUR_ACTION ETHCNTR-3-RA_REPLY_ERROR 3-Error Invalid reply to RAM Access [chars] request 0x%08x from satellite [dec] A request to read/write RAM on satellite access produced unexpected reply. firmware LOG_STD_RECUR_ACTION ETHCNTR-3-UNEXPECTED_EVENT 3-Error Request 0x%08x encountered event [dec] in state [dec] An unexpected event occurred for a ram access request. firmware LOG_STD_RECUR_ACTION ETHCNTR-7-RAM_ACCESS_CMD_GROWING 7-Debug Ethernet Controller: Growing RAM Access [chars] Command The command buffer for RAM Access is being grown dynamically because the original buffer was not big enough firmware LOG_STD_RECUR_ACTION ETHER_CFM_HA-2-GET_BUFFER 2-Critical Ether CFM ISSU client failed to get buffer for message. Error: [dec] [chars] The Ether CFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ethernet-cfm "show logging and show checkpoint client" ETHER_CFM_HA-2-GET_BUFFER 2-Critical Ether CFM ISSU client failed to get buffer for message. Error: [dec] [chars] The Ether CFM HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ethernet-cfm "show logging and show checkpoint client" ETHER_CFM_HA-2-INIT 2-Critical Ether CFM ISSU client initialization failed to [chars]. Error: [dec] [chars] The Ether CFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ethernet-cfm LOG_STD_ACTION ETHER_CFM_HA-2-INIT 2-Critical Ether CFM ISSU client initialization failed to [chars]. Error: [dec] [chars] The Ether CFM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ethernet-cfm LOG_STD_ACTION ETHER_CFM_HA-2-SEND_NEGO_FAILED 2-Critical Ether CFM ISSU client failed to send negotiation message. Error: [dec] [chars] The Ether CFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-cfm "show logging and show checkpoint client" ETHER_CFM_HA-2-SEND_NEGO_FAILED 2-Critical Ether CFM ISSU client failed to send negotiation message. Error: [dec] [chars] The Ether CFM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-cfm "show logging and show checkpoint client" ETHER_CFM_HA-2-SESSION_NEGO 2-Critical Ether CFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Ether CFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-cfm "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-2-SESSION_NEGO 2-Critical Ether CFM ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Ether CFM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-cfm "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-2-SESSION_REGISTRY 2-Critical Ether CFM ISSU client failed to register session information. Error: [dec] [chars] The Ether CFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ethernet-cfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-2-SESSION_REGISTRY 2-Critical Ether CFM ISSU client failed to register session information. Error: [dec] [chars] The Ether CFM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ethernet-cfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-3-INVALID_SESSION 3-Error Ether CFM ISSU client does not have a valid registered session. The Ether CFM ISSU client does not have a valid registered session. ethernet-cfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-3-INVALID_SESSION 3-Error Ether CFM ISSU client does not have a valid registered session. The Ether CFM ISSU client does not have a valid registered session. ethernet-cfm "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-3-MSG_NOT_OK 3-Error Ether CFM ISSU client 'Message Type [dec]' is not compatible The Ether CFM ISSU client received an incompatible message from the peer device. The message cannot be processed. ethernet-cfm "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_CFM_HA-3-MSG_NOT_OK 3-Error Ether CFM ISSU client 'Message Type [dec]' is not compatible The Ether CFM ISSU client received an incompatible message from the peer device. The message cannot be processed. ethernet-cfm "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_CFM_HA-3-MSG_SIZE 3-Error Ether CFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Ether CFM ISSU client failed to calculate the MTU for the specified message. The Ether CFM ISSU client will not able to send the message to the standby device. ethernet-cfm "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_CFM_HA-3-MSG_SIZE 3-Error Ether CFM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Ether CFM ISSU client failed to calculate the MTU for the specified message. The Ether CFM ISSU client will not able to send the message to the standby device. ethernet-cfm "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_CFM_HA-3-SESSION_UNREGISTRY 3-Error Ether CFM ISSU client failed to unregister session information. Error: [dec] [chars] The Ether CFM ISSU client failed to unregister session information. ethernet-cfm "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-3-SESSION_UNREGISTRY 3-Error Ether CFM ISSU client failed to unregister session information. Error: [dec] [chars] The Ether CFM ISSU client failed to unregister session information. ethernet-cfm "show issu session and " "show issu negotiated capability " ETHER_CFM_HA-3-TRANSFORM 3-Error Ether CFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Ether CFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether CFM state between the active device and the standby device is not identical. ethernet-cfm "show issu session and " "show issu negotiated version " ETHER_CFM_HA-3-TRANSFORM 3-Error Ether CFM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Ether CFM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether CFM state between the active device and the standby device is not identical. ethernet-cfm "show issu session and " "show issu negotiated version " ETHER_CFM-3-CONFIG_ERROR 3-Error CFM miss-configuration in the network. Same mpid [dec] configured within the same maintenance name [chars] having [chars] for [chars]. The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association." ETHER_CFM-3-CONFIG_ERROR 3-Error CFM miss-configuration in the network. Same mpid [dec] configured within the same maintenance name [chars] having [chars] for [chars]. The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association." ETHER_CFM-3-CONFIG_ERROR 3-Error CFM miss-configuration in the network. Same mpid [dec] configured within the same maintenance name [chars] having [chars] for [chars]. The same MPID as a locally configured MEP but different source MAC Address than its own. The maintenance name can be either maintenance domain or maintenance association. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Configure the CFM maintenance end points properly " "by giving unique mpid in a particular maintenance " "domain or association." ETHER_CFM-3-CROSS_CONNECTED_CSI 3-Error Service ID of received CC [chars] does not match local Service ID [chars]. For a given service within a domain the Service ID in the CC message should match the locally configured Service ID. ethernet-cfm "Verify that the service ID's are configured correctly using 'show ethernet cfm " "domain. " ETHER_CFM-3-CROSS_CONNECTED_CSI 3-Error Service ID of received CC [chars] does not match local Service ID [chars]. For a given service within a domain the Service ID in the CC message should match the locally configured Service ID. ethernet-cfm "Verify that the service ID's are configured correctly using 'show ethernet cfm " "domain. " ETHER_CFM-3-CROSS_CONNECTED_CSI 3-Error Service ID of received CC [chars] does not match local Service ID [chars]. For a given service within a domain the Service ID in the CC message should match the locally configured Service ID. ethernet-cfm "Verify that the service ID's are configured correctly using 'show ethernet cfm " "domain. " ETHER_CFM-3-CROSS_CONNECTED_SERVICE 3-Error Continuity Check message with unmatched [chars] is received from a remote MEP with mpid [dec] [chars] level [dec] domain [chars] MAC: [enet]. The Continuity Check message whose CSIID or MAID is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network. ethernet-cfm "Configure the CFM CSI ID properly across the " "network." ETHER_CFM-3-CROSS_CONNECTED_SERVICE 3-Error Continuity Check message with unmatched [chars] is received from a remote MEP with mpid [dec] [chars] level [dec] domain [chars] MAC: [enet]. The Continuity Check message whose CSIID or MAID is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network. ethernet-cfm "Configure the CFM CSI ID properly across the " "network." ETHER_CFM-3-CROSS_CONNECTED_SERVICE 3-Error Continuity Check message with unmatched [chars] is received from a remote MEP with mpid [dec] [chars] level [dec] domain [chars] MAC: [enet]. The Continuity Check message whose CSIID or MAID is different from what is locally configured on the device for the given EVC or VLAN thereby indicating that there is a potential for having a cross-connected service in the network. ethernet-cfm "Configure the CFM CSI ID properly across the " "network." ETHER_CFM-3-CROSSCHECK_MEP_MISSING 3-Error The device does not receive any CC messages from a remote MEP with mpid [dec] [chars] that it was expecting to be part of the [chars] in the domain [chars] from MAC: [enet]. The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. " ETHER_CFM-3-CROSSCHECK_MEP_MISSING 3-Error The device does not receive any CC messages from a remote MEP with mpid [dec] [chars] that it was expecting to be part of the [chars] in the domain [chars] from MAC: [enet]. The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. " ETHER_CFM-3-CROSSCHECK_MEP_MISSING 3-Error The device does not receive any CC messages from a remote MEP with mpid [dec] [chars] that it was expecting to be part of the [chars] in the domain [chars] from MAC: [enet]. The configured remote MEP does not come up during the cross-check start timeout interval. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "There could be a possible fault in the network. " "Check the CFM cross check configurations are " "proper. " ETHER_CFM-3-CROSSCHECK_MEP_UNKNOWN 3-Error The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the [chars] in the domain: [chars]. The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Check whether the CFM crosscheck configurations " "are proper." ETHER_CFM-3-CROSSCHECK_MEP_UNKNOWN 3-Error The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the [chars] in the domain: [chars]. The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Check whether the CFM crosscheck configurations " "are proper." ETHER_CFM-3-CROSSCHECK_MEP_UNKNOWN 3-Error The device received a CC message from a remote MEP having mpid [dec] [chars] with MAC: [enet] that it was not expecting to be part of the [chars] in the domain: [chars]. The received remote MEP is not there in the static list configured. This message may be for a particular vlan or evc with the corresponding MAID or CSIID. ethernet-cfm "Check whether the CFM crosscheck configurations " "are proper." ETHER_CFM-3-FAULT_ALARM 3-Error A fault has occurred in the network for the local MEP having mpid [dec] vlan [dec] [chars] indicating a fault with the event code [chars]. This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEPP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other CSI or MA. ethernet-cfm "There could be a possible fault in the network. " "Check whether the cfm configurations are proper." ETHER_CFM-3-FAULT_ALARM 3-Error A fault has occurred in the network for the local MEP having mpid [dec] vlan [dec] [chars] indicating a fault with the event code [chars]. This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEPP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other CSI or MA. ethernet-cfm "There could be a possible fault in the network. " "Check whether the cfm configurations are proper." ETHER_CFM-3-FAULT_ALARM 3-Error A fault has occurred in the network for the local MEP having mpid [dec] vlan [dec] [chars] indicating a fault with the event code [chars]. This indicates a fault in the network. Event code: RDICCM: Remote MEP has reported RDI in CCM Event code: MACstatus: The last CCM received by this MEP from some remote MEP indicated that the transmitting MEPP's associated MAC is reporting an error status via the Port Status TLV or Interface Status TLV. Event code: RemoteCCM: This MEP is not receiving CCMs from some other MEP in its configured list. Event code: ErrorCCM: This MEP is receiving invalid CCMs. Event code: XconCCM: This MEP is receiving CCMs that could be from some other CSI or MA. ethernet-cfm "There could be a possible fault in the network. " "Check whether the cfm configurations are proper." ETHER_CFM-3-FORWARDING_LOOP 3-Error Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the [chars]. The device is receiving its own CC messages for a particular vlan or evc within the same CSI or MA. ethernet-cfm "Configure the CFM maintenance points properly " "to avoid the forwarding loop." ETHER_CFM-3-FORWARDING_LOOP 3-Error Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the [chars]. The device is receiving its own CC messages for a particular vlan or evc within the same CSI or MA. ethernet-cfm "Configure the CFM maintenance points properly " "to avoid the forwarding loop." ETHER_CFM-3-FORWARDING_LOOP 3-Error Continuity Check message is received with same source MAC [enet] and mpid [dec] [chars] of its own in the [chars]. The device is receiving its own CC messages for a particular vlan or evc within the same CSI or MA. ethernet-cfm "Configure the CFM maintenance points properly " "to avoid the forwarding loop." ETHER_CFM-3-LR_FROM_WRONG_FP 3-Error received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination An unknown destination sent a reply to a Loopback messages that was intended to another device. ethernet-cfm "Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message." ETHER_CFM-3-LR_FROM_WRONG_FP 3-Error received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination An unknown destination sent a reply to a Loopback messages that was intended to another device. ethernet-cfm "Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message." ETHER_CFM-3-LR_FROM_WRONG_FP 3-Error received Loopback Reply with correct Transaction IDentifier but from a Maintenance Point different than Loopback Message's destination An unknown destination sent a reply to a Loopback messages that was intended to another device. ethernet-cfm "Verify if the correct destination mac address was specified in the Command Line Interface" " while sending Loopback Message." ETHER_CFM-3-MEP_NOT_CONFIGURED 3-Error received CC from unconfigured remote MEP. While performing cross check a CC message was received from a remote MEP which is not configured under the domain submode. ethernet-cfm "Verify if the remote MEP should be added to the remote MEP list under the domain" " using 'show ethernet cfm domain." ETHER_CFM-3-MEP_NOT_CONFIGURED 3-Error received CC from unconfigured remote MEP. While performing cross check a CC message was received from a remote MEP which is not configured under the domain submode. ethernet-cfm "Verify if the remote MEP should be added to the remote MEP list under the domain" " using 'show ethernet cfm domain." ETHER_CFM-3-MEP_NOT_CONFIGURED 3-Error received CC from unconfigured remote MEP. While performing cross check a CC message was received from a remote MEP which is not configured under the domain submode. ethernet-cfm "Verify if the remote MEP should be added to the remote MEP list under the domain" " using 'show ethernet cfm domain." ETHER_CFM-3-RCV_LOCAL_MPID 3-Error MPID of CC matches local MPID. The remote MPID matches a MPID configured locally for the service. ethernet-cfm "Either the local MPID or remote MPID should be changed as the MPID " " should be unique for a given service in a network" ETHER_CFM-3-RCV_LOCAL_MPID 3-Error MPID of CC matches local MPID. The remote MPID matches a MPID configured locally for the service. ethernet-cfm "Either the local MPID or remote MPID should be changed as the MPID " " should be unique for a given service in a network" ETHER_CFM-3-RCV_LOCAL_MPID 3-Error MPID of CC matches local MPID. The remote MPID matches a MPID configured locally for the service. ethernet-cfm "Either the local MPID or remote MPID should be changed as the MPID " " should be unique for a given service in a network" ETHER_CFM-3-REMOTE_MEP_DOWN 3-Error Remote MEP mpid [dec] [chars] [chars] in domain [chars] changed state to down with event code [chars]. The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB ethernet-cfm "Check the remote CFM configurations using CFM " " utilities like traceroute and ping." ETHER_CFM-3-REMOTE_MEP_DOWN 3-Error Remote MEP mpid [dec] [chars] [chars] in domain [chars] changed state to down with event code [chars]. The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB ethernet-cfm "Check the remote CFM configurations using CFM " " utilities like traceroute and ping." ETHER_CFM-3-REMOTE_MEP_DOWN 3-Error Remote MEP mpid [dec] [chars] [chars] in domain [chars] changed state to down with event code [chars]. The entry in CCDB corresponding to this MEP times out or the device receives a CC message with zero hold-time Event code: LastGasp: A valid Continuity Check message with a zero hold-time is received from a remote MEP and the device either has a valid non-expired CCDB ethernet-cfm "Check the remote CFM configurations using CFM " " utilities like traceroute and ping." ETHER_CFM-3-TM_EGRESS_BOUNDRY 3-Error egress path found for TM is at a higher level than the traceroute message. Traceroute found a domain boundry on egress since the egress port level is higher than the Traceroute Message level. ethernet-cfm "Check if the MIP level on the egress port is at appropriate level." ETHER_CFM-3-TM_EGRESS_BOUNDRY 3-Error egress path found for TM is at a higher level than the traceroute message. Traceroute found a domain boundry on egress since the egress port level is higher than the Traceroute Message level. ethernet-cfm "Check if the MIP level on the egress port is at appropriate level." ETHER_CFM-3-TM_EGRESS_BOUNDRY 3-Error egress path found for TM is at a higher level than the traceroute message. Traceroute found a domain boundry on egress since the egress port level is higher than the Traceroute Message level. ethernet-cfm "Check if the MIP level on the egress port is at appropriate level." ETHER_CFM-5-IGNORED_VLAN 5-Notice Ignored VLAN [dec] in '[chars]' Invalid VLAN was ignored in the configuration. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-5-IGNORED_VLAN 5-Notice Ignored VLAN [dec] in '[chars]' Invalid VLAN was ignored in the configuration. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-5-IGNORED_VLAN 5-Notice Ignored VLAN [dec] in '[chars]' Invalid VLAN was ignored in the configuration. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-CROSSCHECK_SERVICE_UP 6-Information The device received CC messages from all remote MEPs within a given [chars] in the maintenance domain [chars]. The service configured either CSI or MA is up as it receives CC messages from all remote statically configured MEPs. ethernet-cfm "Information message only." ETHER_CFM-6-CROSSCHECK_SERVICE_UP 6-Information The device received CC messages from all remote MEPs within a given [chars] in the maintenance domain [chars]. The service configured either CSI or MA is up as it receives CC messages from all remote statically configured MEPs. ethernet-cfm "Information message only." ETHER_CFM-6-CROSSCHECK_SERVICE_UP 6-Information The device received CC messages from all remote MEPs within a given [chars] in the maintenance domain [chars]. The service configured either CSI or MA is up as it receives CC messages from all remote statically configured MEPs. ethernet-cfm "Information message only." ETHER_CFM-6-ENTER_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters AIS defect condition Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters AIS defect condition Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters AIS defect condition Ethernet cfm mep has entered AIS defect condition. This is due to receive of ETH-AIS or ETH-LCK frames or CCM errors causing signal fail condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_AIS_INT 6-Information Interface [chars] enters AIS defect condition for [chars] direction Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_AIS_INT 6-Information Interface [chars] enters AIS defect condition for [chars] direction Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_AIS_INT 6-Information Interface [chars] enters AIS defect condition for [chars] direction Interface has entered AIS defect condition. This is due to traffic effecting indication from lower layer OAM like 802.3ah ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters LCK defect condition Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters LCK defect condition Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] enters LCK defect condition Ethernet cfm mep has entered LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK_INT 6-Information Interface [chars] enters LCK defect condition for [chars] direction Interface is put in OOS state through exec cli for input direction ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK_INT 6-Information Interface [chars] enters LCK defect condition for [chars] direction Interface is put in OOS state through exec cli for input direction ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-ENTER_LCK_INT 6-Information Interface [chars] enters LCK defect condition for [chars] direction Interface is put in OOS state through exec cli for input direction ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited AIS defect condition Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited AIS defect condition Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_AIS 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited AIS defect condition Ethernet cfm mep has exited AIS defect condition. This is due to not receiving ETH-AIS or ETH-LCK frames for expiry threshold or mep up state if LOC error happened before. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_AIS_INT 6-Information Interface [chars] exited AIS defect condition for [chars] direction LOG_STD_NO_ACTION ethernet-cfm "Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state" ETHER_CFM-6-EXIT_AIS_INT 6-Information Interface [chars] exited AIS defect condition for [chars] direction LOG_STD_NO_ACTION ethernet-cfm "Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state" ETHER_CFM-6-EXIT_AIS_INT 6-Information Interface [chars] exited AIS defect condition for [chars] direction LOG_STD_NO_ACTION ethernet-cfm "Interface has existed AIS defect condition. This is due to " "clearing of traffic effecting condition and 802.3ah entering " "in send_any operational state" ETHER_CFM-6-EXIT_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited LCK defect condition Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited LCK defect condition Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_LCK 6-Information local mep with mpid [dec] level [dec] id [dec] dir [chars] Interface [chars] exited LCK defect condition Ethernet cfm mep has exited LCK Maintenance condition. Id refers to local mep vlan id or bridge-domain id. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_LCK_INT 6-Information Interface [chars] exited LCK defect condition for [chars] direction Interface has exited LCK defect condition. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_LCK_INT 6-Information Interface [chars] exited LCK defect condition for [chars] direction Interface has exited LCK defect condition. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-EXIT_LCK_INT 6-Information Interface [chars] exited LCK defect condition for [chars] direction Interface has exited LCK defect condition. ethernet-cfm "LOG_STD_NO_ACTION" ETHER_CFM-6-REMOTE_MEP_UP 6-Information Continuity Check message is received from a remote MEP with mpid [dec] [chars] [chars] domain [chars] event code [chars]. A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MAID or CSIID ethernet-cfm "Information message only." ETHER_CFM-6-REMOTE_MEP_UP 6-Information Continuity Check message is received from a remote MEP with mpid [dec] [chars] [chars] domain [chars] event code [chars]. A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MAID or CSIID ethernet-cfm "Information message only." ETHER_CFM-6-REMOTE_MEP_UP 6-Information Continuity Check message is received from a remote MEP with mpid [dec] [chars] [chars] domain [chars] event code [chars]. A CC message is received from remote MEP which is up. Event code: New: A remote MEP first comes up that is when we receive a CC message from the remote MEP for the first time. Event code: Returning: The device receives a CC message from a MEP for which it has an expired CCDB entry. Event code: PortState: The device receives a CC message from a remote MEP for which it has a valid CCDB entry and the message indicates a port status change This message may be for a particular vlan or evc with the corresponding MAID or CSIID ethernet-cfm "Information message only." ETHER_INFRA_HA-2-GET_BUFFER 2-Critical Ether INFRA ISSU client failed to get buffer for message. Error: [dec] [chars] The Ether INFRA HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ether-infra "show logging and show checkpoint client" ETHER_INFRA_HA-2-GET_BUFFER 2-Critical Ether INFRA ISSU client failed to get buffer for message. Error: [dec] [chars] The Ether INFRA HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ether-infra "show logging and show checkpoint client" ETHER_INFRA_HA-2-INIT 2-Critical Ether INFRA ISSU client initialization failed to [chars]. Error: [dec] [chars] The Ether INFRA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ether-infra LOG_STD_ACTION ETHER_INFRA_HA-2-INIT 2-Critical Ether INFRA ISSU client initialization failed to [chars]. Error: [dec] [chars] The Ether INFRA ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ether-infra LOG_STD_ACTION ETHER_INFRA_HA-2-SEND_NEGO_FAILED 2-Critical Ether INFRA ISSU client failed to send negotiation message. Error: [dec] [chars] The Ether INFRA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-infra "show logging and show checkpoint client" ETHER_INFRA_HA-2-SEND_NEGO_FAILED 2-Critical Ether INFRA ISSU client failed to send negotiation message. Error: [dec] [chars] The Ether INFRA ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-infra "show logging and show checkpoint client" ETHER_INFRA_HA-2-SESSION_NEGO 2-Critical Ether INFRA ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Ether INFRA ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-infra "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-2-SESSION_NEGO 2-Critical Ether INFRA ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Ether INFRA ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-infra "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-2-SESSION_REGISTRY 2-Critical Ether INFRA ISSU client failed to register session information. Error: [dec] [chars] The Ether INFRA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ether-infra "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-2-SESSION_REGISTRY 2-Critical Ether INFRA ISSU client failed to register session information. Error: [dec] [chars] The Ether INFRA ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ether-infra "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-3-INVALID_SESSION 3-Error Ether INFRA ISSU client does not have a valid registered session. The Ether INFRA ISSU client does not have a valid registered session. ether-infra "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-3-INVALID_SESSION 3-Error Ether INFRA ISSU client does not have a valid registered session. The Ether INFRA ISSU client does not have a valid registered session. ether-infra "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-3-MSG_NOT_OK 3-Error Ether INFRA ISSU client 'Message Type [dec]' is not compatible The Ether INFRA ISSU client received an incompatible message from the peer device. The message cannot be processed. ether-infra "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_INFRA_HA-3-MSG_NOT_OK 3-Error Ether INFRA ISSU client 'Message Type [dec]' is not compatible The Ether INFRA ISSU client received an incompatible message from the peer device. The message cannot be processed. ether-infra "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_INFRA_HA-3-MSG_SIZE 3-Error Ether INFRA ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Ether INFRA ISSU client failed to calculate the MTU for the specified message. The Ether INFRA ISSU client will not able to send the message to the standby device. ether-infra "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_INFRA_HA-3-MSG_SIZE 3-Error Ether INFRA ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Ether INFRA ISSU client failed to calculate the MTU for the specified message. The Ether INFRA ISSU client will not able to send the message to the standby device. ether-infra "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_INFRA_HA-3-SESSION_UNREGISTRY 3-Error Ether INFRA ISSU client failed to unregister session information. Error: [dec] [chars] The Ether INFRA ISSU client failed to unregister session information. ether-infra "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-3-SESSION_UNREGISTRY 3-Error Ether INFRA ISSU client failed to unregister session information. Error: [dec] [chars] The Ether INFRA ISSU client failed to unregister session information. ether-infra "show issu session and " "show issu negotiated capability " ETHER_INFRA_HA-3-TRANSFORM 3-Error Ether INFRA ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Ether INFRA ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether INFRA state between the active device and the standby device is not identical. ether-infra "show issu session and " "show issu negotiated version " ETHER_INFRA_HA-3-TRANSFORM 3-Error Ether INFRA ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Ether INFRA ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether INFRA state between the active device and the standby device is not identical. ether-infra "show issu session and " "show issu negotiated version " ETHER_LMI_HA-2-GET_BUFFER 2-Critical Ether LMI ISSU client failed to get buffer for message. Error: [dec] [chars] The Ether LMI HA client failed to get buffer space for building chkpt message. Message cannot be sent to standby device. If a problem occurs the standby device cannot be brought up properly. ethernet-lmi "show logging and show checkpoint client" ETHER_LMI_HA-2-INIT 2-Critical Ether LMI ISSU client initialization failed to [chars]. Error: [dec] [chars] The Ether LMI ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ethernet-lmi LOG_STD_ACTION ETHER_LMI_HA-2-SEND_NEGO_FAILED 2-Critical Ether LMI ISSU client failed to send negotiation message. Error: [dec] [chars] The Ether LMI ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-lmi "show logging and show checkpoint client" ETHER_LMI_HA-2-SESSION_NEGO 2-Critical Ether LMI ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The Ether LMI ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ethernet-lmi "show issu session and " "show issu negotiated capability " ETHER_LMI_HA-2-SESSION_REGISTRY 2-Critical Ether LMI ISSU client failed to register session information. Error: [dec] [chars] The Ether LMI ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ethernet-lmi "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_LMI_HA-3-INVALID_SESSION 3-Error Ether LMI ISSU client does not have a valid registered session. The Ether LMI ISSU client does not have a valid registered session. ethernet-lmi "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHER_LMI_HA-3-MSG_NOT_OK 3-Error Ether LMI ISSU client 'Message Type [dec]' is not compatible The Ether LMI ISSU client received an incompatible message from the peer device. The message cannot be processed. ethernet-lmi "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_LMI_HA-3-MSG_SIZE 3-Error Ether LMI ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The Ether LMI ISSU client failed to calculate the MTU for the specified message. The Ether LMI ISSU client will not able to send the message to the standby device. ethernet-lmi "show issu message group and " "show issu session and " "show issu negotiated version " ETHER_LMI_HA-3-SESSION_UNREGISTRY 3-Error Ether LMI ISSU client failed to unregister session information. Error: [dec] [chars] The Ether LMI ISSU client failed to unregister session information. ethernet-lmi "show issu session and " "show issu negotiated capability " ETHER_LMI_HA-3-TRANSFORM 3-Error Ether LMI ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The Ether LMI ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the Ether LMI state between the active device and the standby device is not identical. ethernet-lmi "show issu session and " "show issu negotiated version " ETHER_MODULE-3-INVALID_DATA_INSTANCE 3-Error interface type [chars] slot [dec] port [dec] vc [dec] : [chars] Data required to support the interface is not available. asr1k-io-internal LOG_STD_SH_TECH_ACTION ETHER_MODULE-3-UNSUPPORTED_DATA 3-Error Data conversion error [chars] 0x%X An internal software error has occured when converting the data specified in the message from one representation to another. asr1k-io-internal LOG_STD_SH_TECH_ACTION ETHER_PLATFORM_SW-3-BD_NULL 3-Error Unable to get bridge-domain [dec] information for EFP [dec] The software dataplane was unable to get the bridge-domain information for the EFP. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-BD_NULL 3-Error Unable to get bridge-domain [dec] information for EFP [dec] The software dataplane was unable to get the bridge-domain information for the EFP. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_CHNK_LCK_FAILED 3-Error Unable to lock memory while learning C-MAC to B-MAC mapping The Ethernet Software Platform was unable to lock a particular piece of memory while attempting to learn a C-MAC to B-MAC mapping ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_CHNK_LCK_FAILED 3-Error Unable to lock memory while learning C-MAC to B-MAC mapping The Ethernet Software Platform was unable to lock a particular piece of memory while attempting to learn a C-MAC to B-MAC mapping ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_DEL_MAP_FAILED 3-Error Unable to remove 802.1ah mapping entry for B-MAC [enet] C-MAC [enet]. The Ethernet Software Platform was unable to remove an 802.1ah mapping entry from the tree of entries. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_DEL_MAP_FAILED 3-Error Unable to remove 802.1ah mapping entry for B-MAC [enet] C-MAC [enet]. The Ethernet Software Platform was unable to remove an 802.1ah mapping entry from the tree of entries. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_PROC_ENQ_FAILED 3-Error Unable to enqueue a request to learn a C-MAC to B-MAC mapping An error occurred while trying to enqueue a request to learn a C-MAC to B-MAC mapping. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-DOT1AH_PROC_ENQ_FAILED 3-Error Unable to enqueue a request to learn a C-MAC to B-MAC mapping An error occurred while trying to enqueue a request to learn a C-MAC to B-MAC mapping. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-EFP_CANNOT_CLEAR_DIM 3-Error Unable to clear EFP's encapsulation data An error occurred while trying to clear the encapsulation data for an EFP. ether-infra "Enable debugging with 'debug ethernet service " "instace'. Retry the operation that caused the " "error to see if additional debugging messages " "are provided. If the error persists you may need " "to reload the router." ETHER_PLATFORM_SW-3-EFP_CANNOT_CLEAR_DIM 3-Error Unable to clear EFP's encapsulation data An error occurred while trying to clear the encapsulation data for an EFP. ether-infra "Enable debugging with 'debug ethernet service " "instace'. Retry the operation that caused the " "error to see if additional debugging messages " "are provided. If the error persists you may need " "to reload the router." ETHER_PLATFORM_SW-3-NO_PD_EFP 3-Error Unable to find software platform EFP information for EFP ID [dec] The software dataplane was unable to get the platform dependent EFP information for the EFP with the given ID. ether-infra "This error may indicate a bug in the software " "dataplane implementation. If the error " "occurs after a specific configuration was performed " "then precisely record those configuration steps. " "Contact your Cisco technical support " "representative and provide the gathered " "information." ETHER_PLATFORM_SW-3-NO_PD_EFP 3-Error Unable to find software platform EFP information for EFP ID [dec] The software dataplane was unable to get the platform dependent EFP information for the EFP with the given ID. ether-infra "This error may indicate a bug in the software " "dataplane implementation. If the error " "occurs after a specific configuration was performed " "then precisely record those configuration steps. " "Contact your Cisco technical support " "representative and provide the gathered " "information." ETHER_PLATFORM_SW-3-REWRITE_FAILED 3-Error Unable to apply rewrite to packet An error occurred while trying to perform an ingress rewrite operation on a frame. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_PLATFORM_SW-3-REWRITE_FAILED 3-Error Unable to apply rewrite to packet An error occurred while trying to perform an ingress rewrite operation on a frame. ether-infra "This error may be transient. If the error " "persists you may need to reload the router." ETHER_SERVICE_IPC-3-IPC_RESP_ERROR 3-Error IPC send response error [chars] An error was detected in the response for an IPC message that was transmitted to the peer. ether-infra "This error could be transient. If this error persists " "copy the error message exactly as it appears " "and report it to your technical support representative." ETHER_SERVICE_IPC-3-IPC_RESP_ERROR 3-Error IPC send response error [chars] An error was detected in the response for an IPC message that was transmitted to the peer. ether-infra "This error could be transient. If this error persists " "copy the error message exactly as it appears " "and report it to your technical support representative." ETHER_SERVICE_IPC-3-IPC_TRANSMIT_FAILED 3-Error IPC message transmission failure [chars] An error was detected when transmitting an IPC message between Standby RP and SP. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred. ether-infra "This could be a transient error. If this error persists " "copy the error message exactly as it appears and report it " "to your technical support representative." ETHER_SERVICE_IPC-3-IPC_TRANSMIT_FAILED 3-Error IPC message transmission failure [chars] An error was detected when transmitting an IPC message between Standby RP and SP. The failure most likely occurred because of a software error. The message output identifies the type of error that occurred. ether-infra "This could be a transient error. If this error persists " "copy the error message exactly as it appears and report it " "to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_CREATE 3-Error Unable to create IPC port [chars]. Ethernet Service was unable to create an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_CREATE 3-Error Unable to create IPC port [chars]. Ethernet Service was unable to create an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_REGISTER 3-Error Unable to register IPC port [chars]. Ethernet Service was unable to register an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_REGISTER 3-Error Unable to register IPC port [chars]. Ethernet Service was unable to register an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_REMOVE 3-Error Unable to remove IPC port [chars]. Ethernet Service was unable to remove an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPORT_REMOVE 3-Error Unable to remove IPC port [chars]. Ethernet Service was unable to remove an IPC port ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPROCESSES 3-Error Unable to create IPC processes on [chars]. Ethernet Service was unable to create IPC processes ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCPROCESSES 3-Error Unable to create IPC processes on [chars]. Ethernet Service was unable to create IPC processes ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-3-IPCSESSION 3-Error Unable to open an IPC session for communicating with [chars]. Error: [chars] This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-IPCSESSION 3-Error Unable to open an IPC session for communicating with [chars]. Error: [chars] This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-NOIPCDESC 3-Error Unable to allocate IPC descriptor for Ethernet Service on [chars]. This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-NOIPCDESC 3-Error Unable to allocate IPC descriptor for Ethernet Service on [chars]. This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-NOMEM 3-Error Unable to allocate memory for Ethernet Service on [chars]. This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-NOMEM 3-Error Unable to allocate memory for Ethernet Service on [chars]. This is an internal error ether-infra "Copy the error message exactly as it appears and report it to your" " technical support representative." ETHER_SERVICE_IPC-3-RMI_CALLBACK 3-Error Ethernet Infra encountered an error while processing a callback from the Resource Manager RMI [chars] Ethernet Infra registers with the Resource Manager RMI to ether-infra "show tech" ETHER_SERVICE_IPC-3-RMI_CALLBACK 3-Error Ethernet Infra encountered an error while processing a callback from the Resource Manager RMI [chars] Ethernet Infra registers with the Resource Manager RMI to ether-infra "show tech" ETHER_SERVICE_IPC-3-RMI_FAILED 3-Error Ethernet Infra failed to register with the Resource Manager RMI [chars] Ethernet Infra registers with the Resource Manager RMI to ether-infra "show tech" ETHER_SERVICE_IPC-3-RMI_FAILED 3-Error Ethernet Infra failed to register with the Resource Manager RMI [chars] Ethernet Infra registers with the Resource Manager RMI to ether-infra "show tech" ETHER_SERVICE_IPC-4-NOIPCDATA 4-Warning IPC Message has no data area [chars] Cannot find data area in an IPC message. This is a warning message no action is required ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-4-NOIPCDATA 4-Warning IPC Message has no data area [chars] Cannot find data area in an IPC message. This is a warning message no action is required ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-4-NOIPCPORT 4-Warning IPC port is NULL [chars] Ethernet Service cannot send the message as the IPC port information is NULL. This is a warning message no action is required. ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-4-NOIPCPORT 4-Warning IPC port is NULL [chars] Ethernet Service cannot send the message as the IPC port information is NULL. This is a warning message no action is required. ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-4-NOMESSAGE 4-Warning Message is NULL [chars] Cannot send the message as the message is NULL. This is a warning message no action is required ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE_IPC-4-NOMESSAGE 4-Warning Message is NULL [chars] Cannot send the message as the message is NULL. This is a warning message no action is required ether-infra "Copy the error message exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE-3-EFP_DEBUG_INIT_FAILURE 3-Error The Ether Infra Trace and Debug Library Failed to initialize successfully due to error: [dec] All trace and debug may not work ether-infra "No Action" ETHER_SERVICE-3-EFP_DEBUG_INIT_FAILURE 3-Error The Ether Infra Trace and Debug Library Failed to initialize successfully due to error: [dec] All trace and debug may not work ether-infra "No Action" ETHER_SERVICE-3-EFP_INVALID_TYPE 3-Error [chars] : [chars] is INVALID invalid type ether-infra "Copy the error and send it to TAC" ETHER_SERVICE-3-EFP_INVALID_TYPE 3-Error [chars] : [chars] is INVALID invalid type ether-infra "Copy the error and send it to TAC" ETHER_SERVICE-3-EFP_NO_MEMORY 3-Error [chars] : memory allocation failed for [chars] memory allocation failed ether-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ETHER_SERVICE-3-EFP_NO_MEMORY 3-Error [chars] : memory allocation failed for [chars] memory allocation failed ether-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ETHER_SERVICE-3-EFP_NULL_POINTER 3-Error [chars] : [chars] pointer is NULL NULL pointer ether-infra "Copy the error and send it to TAC" ETHER_SERVICE-3-EFP_NULL_POINTER 3-Error [chars] : [chars] pointer is NULL NULL pointer ether-infra "Copy the error and send it to TAC" ETHER_SERVICE-3-ETHER_CHAN_SERV_INSTANCE_POLICY_REMOVED 3-Error [chars] service policy [chars] has been removed from service instance [dec] of ethernet channel [chars] due to failure to install the policy on member link [chars]. The member link does not support the service policy or installation failed due to resources limitation at the time. ether-infra "Check for any error message that indicates incompatiblity between " "the policy and the member link. Remove the member link from the " "ethernet channel and reconfigure the policy on the service instance. " "If the problem persists copy the error exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE-3-ETHER_CHAN_SERV_INSTANCE_POLICY_REMOVED 3-Error [chars] service policy [chars] has been removed from service instance [dec] of ethernet channel [chars] due to failure to install the policy on member link [chars]. The member link does not support the service policy or installation failed due to resources limitation at the time. ether-infra "Check for any error message that indicates incompatiblity between " "the policy and the member link. Remove the member link from the " "ethernet channel and reconfigure the policy on the service instance. " "If the problem persists copy the error exactly as it appears and " "report it to your technical support representative." ETHER_SERVICE-4-UNSUP_MIRPENABLE 4-Warning %% Not supported since \no ethernet mac-flush notification mirp\ command is configured. \no ethernet mac-flush notification mirp\ is configured. ether-infra "Configure \"ethernet mac-flush notification mirp\" command." ETHER_SERVICE-4-UNSUP_MIRPENABLE 4-Warning %% Not supported since \no ethernet mac-flush notification mirp\ command is configured. \no ethernet mac-flush notification mirp\ is configured. ether-infra "Configure \"ethernet mac-flush notification mirp\" command." ETHER_SERVICE-6-ERR_DISABLED 6-Information [chars] - shutdown service instance [dec] at [chars] Service instance shutdown due to errdisable ether-infra "No Action" ETHER_SERVICE-6-ERR_DISABLED 6-Information [chars] - shutdown service instance [dec] at [chars] Service instance shutdown due to errdisable ether-infra "No Action" ETHER_SERVICE-6-EVC_STATUS_CHANGED 6-Information status of [chars] changed to [chars] EVC status has changed ether-infra "No Action" ETHER_SERVICE-6-EVC_STATUS_CHANGED 6-Information status of [chars] changed to [chars] EVC status has changed ether-infra "No Action" ETHER_SERVICE-6-EVC_VLAN_NOT_CONFIGURED 6-Information VLANs [chars] not configured at [chars] but is in a CEVLAN/EVC map VLANs part of the CEVLAN/EVC map for an EVC associated to an interface but the interface doesn't have those VLANs configured ether-infra "Verify configurations of VLANs on the interface" ETHER_SERVICE-6-EVC_VLAN_NOT_CONFIGURED 6-Information VLANs [chars] not configured at [chars] but is in a CEVLAN/EVC map VLANs part of the CEVLAN/EVC map for an EVC associated to an interface but the interface doesn't have those VLANs configured ether-infra "Verify configurations of VLANs on the interface" ETHER_SERVICE-6-UPDOWN 6-Information Service instance [dec] on interface [chars] changed to [chars] Service instance shutdown due to errdisable ether-infra "No Action" ETHER_SERVICE-6-UPDOWN 6-Information Service instance [dec] on interface [chars] changed to [chars] Service instance shutdown due to errdisable ether-infra "No Action" ETHERCHANNEL_LB-3-MSG_SEND_FAIL 3-Error The load-balance message [dec] has failed to send The load-balancing feature has detected an error while trying to send an internal message. ether-channel "If this message was the result of performing a " "configuration command then try unconfiguring " "and reconfiguring the same command. If the error " "message continues to be displayed then it may " "indicate that the system is low on memory. The " "show memory free command should be used to check " "if the system has sufficient available memory. " "If the system appears to have available memory and " "the error continues to be displayed then please " "contact your Cisco technical support representative " "and provide the representative with the exact error " "message being seen as well as the version of IOS " "being used." ETHERCHANNEL_LB-3-XDR_MSG_XMIT_FAIL 3-Error Failed to transmit XDR message of size [dec] to slot [dec] An error occurred while attempting to send a load-balancing XDR message to the specified slot. ether-channel "Because the message failed to send the specified " "slot may now be out of sync with the rest of the " "system. To correct the issue the card in the " "specified slot may be rebooted at which point " "the full configuration will be re-synced with the " "card in that slot. If the specified slot is zero " "then that message was intended for cards in all " "slots and the router should be reloaded to re-sync" "the entire system." ETHERCHANNEL-2-PROXY_IPC_INIT_FAILED 2-Critical QFP Etherchannel Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP Etherchannel initialization detected that the Proxy IPC interface initialization failed. The EC Bundle interfaces will not be functional while this condition exists. qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-INV_PROXY_MSG 3-Error QFP ETHERCHANNEL Proxy received invalid Message ID [dec] Cisco internal software error. QFP Etherchannel Proxy received an invalid Message ID. This message will be ignored. qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-LOCK_ERROR 3-Error QFP EC Lock Failure: retval:[dec] tries[dec] Cisco internal software error. QFP EC Lock Failure locking attempt failed qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-LOCK_STATE_ERROR 3-Error QFP EC Lock State Failure: retval:[dec] Cisco internal software error. QFP EC Lock State Failure Illegal lock state qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-PROXY_IPC_ALLOC_FAIL 3-Error QFP ETHERCHANNEL Proxy [chars] response lost due to buffer allocation Cisco internal software error. QFP ETHERCHANNEL Proxy message processing detected a IPC buffer allocation failure during response processing. The associated ETHERCHANNEL interface may not be fully functional as a result of this condition. qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-PROXY_SID_UPDATE_COMPLETE_ERROR 3-Error QFP EC Proxy [chars] SID Update Complete w/o Preceeding Lock Cisco internal software error. QFP EC Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected. qfp-ethernet keyword:gec LOG_STD_ACTION ETHERCHANNEL-3-PROXY_SID_UPDATE_LOCK_ERROR 3-Error QFP EC Proxy [chars] Multiple SID Update Locks to same interface Cisco internal software error. QFP EC Proxy message processing detected a Bundle Schedule SID update sequence error. One or more interface schedules could have been affected. qfp-ethernet keyword:gec LOG_STD_ACTION ETHERNET_EVENT-4-MW_BW_CHANGE 4-Warning Available microwave bandwidth for link with source MAC [chars] link ID [dec] on [chars] has changed due to [chars] current is [dec]Mbps nominal is [dec]Mbps. The available microwave bandwidth has changed. The message indicates the reason why the bandwidth changed as well as the currently available bandwidth. If the message indicates that the change was due to VSM then an ITU-T Y.1731 Vendor-Specific Message has been received causing the available microwave bandwidth to be updated. If the message indicates that the change was due to periodic timeout then the local system has not received a VSM within the expected time period and so it has reset the bandwidth back to its nominal value. The current bandwidth represents the bandwidth currently available on the link while the nominal bandwidth represents the maximum bandwidth supported by the link when the microwave signal is not degraded. ethernet-cfm "If the current bandwidth is unexpectedly less than " "the nominal bandwidth then action may be required " "to restore the microwave bandwidth to its fully " "supported capacity." ETHERNET_EVENT-4-MW_BW_CHANGE 4-Warning Available microwave bandwidth for link with source MAC [chars] link ID [dec] on [chars] has changed due to [chars] current is [dec]Mbps nominal is [dec]Mbps. The available microwave bandwidth has changed. The message indicates the reason why the bandwidth changed as well as the currently available bandwidth. If the message indicates that the change was due to VSM then an ITU-T Y.1731 Vendor-Specific Message has been received causing the available microwave bandwidth to be updated. If the message indicates that the change was due to periodic timeout then the local system has not received a VSM within the expected time period and so it has reset the bandwidth back to its nominal value. The current bandwidth represents the bandwidth currently available on the link while the nominal bandwidth represents the maximum bandwidth supported by the link when the microwave signal is not degraded. ethernet-cfm "If the current bandwidth is unexpectedly less than " "the nominal bandwidth then action may be required " "to restore the microwave bandwidth to its fully " "supported capacity." ETHERNET_LACP-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low memory condition. lacp "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." ETHERNET_LACP-3-ISSU_SENDFAILED 3-Error \nLACP ISSU: send message failed rc = [dec]\n The sending of a message has failed. This is an informational message only. lacp LOG_STD_SH_TECH_ACTION ETHERNET_LACP-4-ISSU_INCOMPATIBLE 4-Warning \nlacp-issu-compat: returned FALSE The ISSU compatibility matrix check has failed. This is an informational message only. lacp LOG_STD_SH_TECH_ACTION ETHERNET_LACP-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The ISSU transform has failed. This is an informational message only. lacp LOG_STD_SH_TECH_ACTION ETHERNET_LACP-4-RF_CLIENT_BUNDLE 4-Warning \nLACP HA: Unable initiate checkpoint bundle mode.\n LACP is unable to initialize checkpoint bundle mode. This is an informational message only. lacp LOG_STD_SH_TECH_ACTION ETHERNET_LACP-4-RF_CLIENT_INIT 4-Warning \nLACP HA: Unable to initiate RF client.\n LACP is unable to initialize as a RF client. This is an informational message only. lacp LOG_STD_SH_TECH_ACTION ETHERNET_MLACP-3-PEER_ICCP_VERSION_INCOMPATIBLE 3-Error Peer ICCP version [dec] is incompatible with local ICCP version [dec]. mLACP peer is running with a different version of ICCP. Incompatible ICCP would prevent mLACP from working properly. lacp "Reboot peer with identical IOS version would " "correct the issue. Compatible ICCP version between " "different IOS images can still be achieved by doing " "show lacp multichassis group on the both devices to " "check if ICCP versions are compatible. If ICCP " "versions are incompatible repeat IOS image loading " " and CLI above until a compatible image is loaded." ETHERNET_MLACP-3-SYS_CFG_DUPL_ID 3-Error Remote mLACP peer has duplicate mLACP node-id [dec] A remote mLACP peer is configured with the same mLACP node-id as this device. lacp "Reconfigure the mLACP node-id to be unique between the two " "devices with the mlacp node-id configuration " "command. Refer to the mLACP configuration section of the Cisco " "IOS documentation for more information on configuring mLACP." ETHERNET_MLACP-3-SYS_CFG_INVALID_ID 3-Error Received invalid mLACP node-id [dec] from peer A remote mLACP peer is configured with an invalid mLACP node-id. lacp "Reconfigure the peer to send a valid mLACP node-id with the " "mlacp node-id configuration command. Refer " "to the mLACP configuration section of the Cisco IOS documentation " "for more information on configuring mLACP." ETHERNET_MLACP-4-CORE_CONNECTED 4-Warning mLACP has recovered from a core isolation failure. Attempting to recover [dec] LAGs in redundancy group [dec] mLACP has recovered from core isolation and has attempted to recover the LAGs in the redundancy group. lacp "This message may not require any action. However the " "show lacp multi-chassis group and " "show lacp multi-chassis port-channel commands " "may be used to verify the state of the mLACP port-channels. Reference " "the mLACP section of the IOS documentation for details on core isolation " "failures and related configuration commands." ETHERNET_MLACP-4-CORE_ISOLATION 4-Warning mLACP Core isolation failure: Attempting to failover [dec] LAGs in redundancy group [dec] mLACP has detected isolation from the core and has attempted to failover. lacp "Use the show interchassis redundancy command to determine " "which core facing interface has triggered the isolation failure. Correct the " "failure for the given interface this will clear the mLACP core isolation " "failure. Reference the mLACP section of the IOS documentation for more " "information on core isolation failures and related configuration commands." ETHERNET_MLACP-4-ICRM_CLIENT_RECV_BAD_LEN 4-Warning Received an mLACP TLV with bad length [dec] total message length [dec] The mLACP TLV length is longer than the total message length. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP section " "of the IOS documentation to verify that mLACP is compatible between the IOS " "versions on the two devices. If the versions are compatible and the message still " "appears then please contact your Cisco technical support representative. Provide " "the representative with the exact message being seen as well as the output of the " "following commands show version show run " "show lacp multi-chassis group and show lacp " "multi-chassis port-channel." ETHERNET_MLACP-4-ICRM_CLIENT_RECV_NO_TYPELEN 4-Warning Received an mLACP TLV without a type and/or length field [dec] mLACP received an improperly formatted TLV from the peer. As a result the local and peer devices may have mismatched state data. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP " "section of the IOS documentation to verify that mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices." ETHERNET_MLACP-4-ICRM_CLIENT_RECV_REJ 4-Warning Received rejected mLACP TLV from peer with message ID [dec] A remote mLACP peer has rejected an mLACP TLV. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the mLACP " "section of the IOS documentation to verify that mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices." ETHERNET_MLACP-4-PC_CHANGE 4-Warning mLACP [chars] status changed to [chars] A mLACP port-channel state change event has occurred. This might have been caused by a mLACP failure or recovery event on the local or peer POA in the same redundancy group. It is normal to get these messages during provisioning and administrative actions on the mLACP port-channel. lacp "User should debug further to analyze root cause of the event. Use " "show redundancy interchassis " "show lacp multi-chassis port-channel " "show lacp multi-chassis group and " "show lacp internal on both POAs to check " "mLACP port-channel health. If any failure exists appropriate " "actions should be taken to recover port-channel from failure. " "If failure persists then please contact your Cisco technical " "support representative and provide the collected information." ETHERNET_MLACP-4-PEER_DISCONNECT 4-Warning An mLACP peer has disconnected from redundancy group [dec] attempting to reconnect mLACP has detected that a peer device from the specified redundancy group has disconnected. mLACP will attempt to reconnect to the device until successful. lacp "This message is typically caused by a configuration event on the peer router and " "so no action may be necessary. However if this message is unexpected then issue " "the show redundancy interchassis command on both the local and " "peer mLACP devices to determine which peer member IP has lost communication. Use this " "information to further debug the network communication issue and re-enable communication " "with the peer. Reference the mLACP section of the IOS documentation for more information " "on peer down failures." ETHERNET_MLACP-4-PEER_DOWN 4-Warning mLACP Peer down failure: Attempting to make [dec] local LAGs active in redundancy group [dec] mLACP has detected a peer down failure and has attempted to make the local port-channels become active. lacp "The peer down failure should be corrected by re-enabling communication " "with the peer mLACP device. Use the show redundancy interchassis " "command on both the local and peer mLACP devices to determine which peer member IP " "has lost communication. Use this information to further debug the network communication " "issue and re-enable communication with the peer. Reference the mLACP section of the IOS " "documentation for more information on peer down failures." ETHERNET_MLACP-4-PEER_RECONNECT_FAILED 4-Warning The attempt to reconnect to the peer in redundancy group [dec] has failed After an mLACP peer device disconnected an attempt was made to reconnect however that attempt has failed. lacp "To reinitialize the connection unconfigure mlacp interchassis group " "from the port-channel and then reconfigure it. After doing that issue " "show redundancy interchassis to get the peer member IP " "connection status and the mLACP connection state. If the peer member IP " "connection status is not CONNECTED then there is a more basic communication " "issue that needs to be fixed. Otherwise if the peer member IP is CONNECTED but " "the mLACP state is not CONNECTED then there could be a software issue. In that " "case collect the output of show redundancy interchassis " "show lacp multi-chassis group and " "show lacp multi-chassis port-channel. Then please contact your " "Cisco technical support representative and provide the collected information." ETHERNET_MLACP-4-PEER_UP 4-Warning mLACP has recovered from a peer down failure in redundancy group [dec] mLACP is now in communication with the peer device and has recovered from a previous peer down failure. lacp "This message may not require any action. However the " "show lacp multi-chassis group and " "show lacp multi-chassis port-channel commands may be used " "to verify the state of the mLACP port-channels. Reference the mLACP section " "of the IOS documentation for details on peer down failures and related " "configuration commands." ETHERNET_MLACP-6-PEER_CONNECT 6-Information mLACP peer is now connected in redundancy group [dec] This message indicates that the local mLACP device is now connected to a peer device in the specified redundancy group. lacp "No action is required. To view the peer information the command " "show lacp multi-chassis port-channel or " "show lacp multi-chassis group may be issued." ETHERNET_OAM-2-CRIT_ERR 2-Critical The Ethernet OAM protocol has encountered the critical error: [chars]. The protocol has run into a critical error. The reason should be given in the brackets. ether-oam LOG_STD_ACTION ETHERNET_OAM-2-GET_BUFFER 2-Critical ETHERNET OAM ISSU client failed to get buffer for message. Error: [dec] [chars] The ETHERNET OAM ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-oam "show logging and show checkpoint client" ETHERNET_OAM-2-INIT 2-Critical ETHERNET OAM ISSU client initialization failed to [chars]. Error: [dec] [chars] The ETHERNET OAM ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ether-oam LOG_STD_ACTION ETHERNET_OAM-2-SEND_NEGO_FAILED 2-Critical ETHERNET OAM ISSU client failed to send negotiation message. Error: [dec] [chars] The ETHERNET OAM ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-oam "show logging and show checkpoint client" ETHERNET_OAM-2-SESSION_NEGO 2-Critical ETHERNET OAM ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The ETHERNET OAM ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ether-oam "show issu session and " "show issu negotiated capability " ETHERNET_OAM-2-SESSION_REGISTRY 2-Critical ETHERNET OAM ISSU client failed to register session information. Error: [dec] [chars] The ETHERNET OAM ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ether-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHERNET_OAM-3-INVALID_SESSION 3-Error ETHERNET OAM ISSU client does not have a valid registered session. The ETHERNET OAM ISSU client does not have a valid registered session. ether-oam "show issu capability entries and " "show issu session and " "show issu negotiated capability " ETHERNET_OAM-3-LOOPBACK_ERROR 3-Error Loopback operation on interface [chars] has encountered an error[chars]. Because of the specified error the loopback operation has ended abnormally. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-3-MSG_SIZE 3-Error ETHERNET OAM ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The ETHERNET OAM ISSU client failed to calculate the MTU for the specified message. The ETHERNET OAM ISSU client is not able to send the message to the standby device. ether-oam "show issu message group and " "show issu session and " "show issu negotiated version " ETHERNET_OAM-3-SESSION_UNREGISTRY 3-Error ETHERNET OAM ISSU client failed to unregister session information. Error: [dec] [chars] The ETHERNET OAM ISSU client failed to unregister session information. ether-oam "show issu session and " "show issu negotiated capability " ETHERNET_OAM-3-TRANSFORM_FAIL 3-Error ETHERNET OAM ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The ETHERNET OAM ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the ETHERNET OAM state between the active device and the standby device is not identical. ether-oam "show issu session and " "show issu negotiated version " ETHERNET_OAM-4-ISSU_INCOMPATIBLE 4-Warning \nether_oam-issu-compat: returned FALSE The compatibility checking has failed ether-oam LOG_STD_SH_TECH_ACTION ETHERNET_OAM-5-EVENTTLV 5-Notice [chars] is received from the remote client on interface [chars]. An Event TLV is received from the remote OAM client. It must have detected errors in receiving frames from this local interface. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-5-LINK_MONITOR 5-Notice [chars] detected over the last [chars] on interface [chars]. A monitored error has been detected to have crossed the user-specified threshold. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-CRITICAL_EVENT 6-Information The client on interface [chars] has received a Critical Event indication from its remote peer action = [chars] An OAMPDU has been received from the remote client that indicates a Critical Event has occurred. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down. ether-oam "Investigate the issue on the remote peer" ETHERNET_OAM-6-CRITICAL_EVENT_CLEAR 6-Information The client on interface [chars] has received a clear of the Critical Event indication from its remote peer action = [chars] An OAMPDU has been received from the remote client that indicates that the Critical Event condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-DYING_GASP 6-Information The client on interface [chars] has received a Dying Gasp indication from its remote peer failure reason = [chars] action = [chars] An OAMPDU has been received from the remote client that indicates a Dying Gasp which may signal that the remote client is about to go down. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down. ether-oam "Investigate the issue on the remote peer" ETHERNET_OAM-6-DYING_GASP_CLEAR 6-Information The client on interface [chars] has received a clear of the Dying Gasp indication from its remote peer action = [chars] An OAMPDU has been received from the remote client that indicates that the Dying Gasp condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-ENTER_SESSION 6-Information The client on interface [chars] has entered the OAM session. Ethernet OAM client on the specified interface has detected a remote client and has entered the OAM session. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-EXIT_SESSION 6-Information The client on interface [chars] has left the OAM session. Ethernet OAM client on the specified interface has experienced some state change. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-LINK_FAULT 6-Information The client on interface [chars] has received a Link Fault indication from its remote peer action = [chars] An OAMPDU has been received from the remote client that indicates a Link Fault has been detected. This indicates a fault has occurred in the receive direction of the sending client. The indicated action will be performed. If the action is error-block the link will go into error-block state where data traffic is blocked but link-oam can still be exchanged. If the action is error-disable the link is brought down. ether-oam "Check the wiring between the two interfaces." ETHERNET_OAM-6-LINK_FAULT_CLEAR 6-Information The client on interface [chars] has received a clear of the Link Fault indication from its remote peer action = [chars] An OAMPDU has been received from the remote client that indicates that the Link Fault condition previously seen has cleared. If the action was error-block traffic on the link will now be re-enabled. Error-disable state can only be cleared by performing a shut/no shut of the interface. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-LINK_TIMEOUT 6-Information The client on interface [chars] has timed out and exited the OAM session. The Ethernet OAM client on the specified interface has not received any OAMPDUs in the number of seconds for timeout that were configured by the user. The client has exited the OAM session. ether-oam LOG_STD_NO_ACTION ETHERNET_OAM-6-LOOPBACK 6-Information Interface [chars] has [chars] the [chars] loopback mode. The specified interface has entered or exited loopback mode because of protocol control or an external event such as the interface link going down. ether-oam LOG_STD_NO_ACTION ETHERNET_PMLACP-3-PEER_ICCP_VERSION_INCOMPATIBLE 3-Error Peer ICCP version [dec] is incompatible with local ICCP version [dec]. P-mLACP peer is running with a different version of ICCP. Incompatible ICCP would prevent P-mLACP from working properly. lacp "Reboot peer with identical IOS version would " "correct the issue. Compatible ICCP version between " "different IOS images can still be achieved by doing " "show lacp multichassis load-balance group on the both" " devices to check if ICCP versions are compatible. If ICCP " "versions are incompatible repeat IOS image loading " " and CLI above until a compatible image is loaded." ETHERNET_PMLACP-3-SYS_CFG_DUPL_ID 3-Error Remote P-mLACP peer has duplicate P-mLACP node-id [dec] A remote P-mLACP peer is configured with the same P-mLACP node-id as this device. lacp "Reconfigure the P-mLACP node-id to be unique between the two " "devices with the mlacp node-id configuration " "command. Refer to the P-mLACP configuration section of the Cisco " "IOS documentation for more information on configuring P-mLACP." ETHERNET_PMLACP-3-SYS_CFG_INVALID_ID 3-Error Received invalid P-mLACP node-id [dec] from peer A remote P-mLACP peer is configured with an invalid P-mLACP node-id. lacp "Reconfigure the peer to send a valid P-mLACP node-id with the " "mlacp node-id configuration command. Refer " "to the P-mLACP configuration section of the Cisco IOS documentation " "for more information on configuring P-mLACP." ETHERNET_PMLACP-4-CORE_CONNECTED 4-Warning P-mLACP has recovered from a core isolation failure. Attempting to recover [dec] ports in redundancy group [dec] P-mLACP has recovered from core isolation and has attempted to recover the ports in the redundancy group. lacp "This message may not require any action. However the " "show lacp multi-chassis load-balance group and " "show lacp multi-chassis load-balance port-channel commands " "may be used to verify the state of the P-mLACP port-channels. Reference " "the P-mLACP section of the IOS documentation for details on core isolation " "failures and related configuration commands." ETHERNET_PMLACP-4-CORE_ISOLATION 4-Warning P-mLACP Core isolation failure: Attempting to failover [dec] ports in redundancy group [dec] P-mLACP has detected isolation from the core and has attempted to failover. lacp "Use the show interchassis redundancy command to determine " "which core facing interface has triggered the isolation failure. Correct the " "failure for the given interface this will clear the P-mLACP core isolation " "failure. Reference the P-mLACP section of the IOS documentation for more " "information on core isolation failures and related configuration commands." ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_BAD_LEN 4-Warning Received an P-mLACP TLV with bad length [dec] total message length [dec] The P-mLACP TLV length is longer than the total message length. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP section " "of the IOS documentation to verify that P-mLACP is compatible between the IOS " "versions on the two devices. If the versions are compatible and the message still " "appears then please contact your Cisco technical support representative. Provide " "the representative with the exact message being seen as well as the output of the " "following commands show version show run " "show lacp multi-chassis load-balance group and show lacp " "multi-chassis load-balance port-channel." ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_NO_TYPELEN 4-Warning Received an P-mLACP TLV without a type and/or length field [dec] P-mLACP received an improperly formatted TLV from the peer. As a result the local and peer devices may have mismatched state data. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP " "section of the IOS documentation to verify that P-mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices." ETHERNET_PMLACP-4-ICRM_CLIENT_RECV_REJ 4-Warning Received rejected P-mLACP TLV from peer with message ID [dec] A remote P-mLACP peer has rejected an P-mLACP TLV. lacp "Issue the show version command on the local and remote " "devices to get the versions of IOS that are running. Reference the P-mLACP " "section of the IOS documentation to verify that P-mLACP is compatible between " "the IOS versions on the two devices. If the versions are compatible and the " "message still appears then please contact your Cisco technical support " "representative and provide the representative with the exact error message " "being seen as well as the versions of IOS from both devices." ETHERNET_PMLACP-4-PEER_DISCONNECT 4-Warning An P-mLACP peer has disconnected from redundancy group [dec] attempting to reconnect P-mLACP has detected that a peer device from the specified redundancy group has disconnected. P-mLACP will attempt to reconnect to the device until successful. lacp "This message is typically caused by a configuration event on the peer router and " "so no action may be necessary. However if this message is unexpected then issue " "the show redundancy interchassis command on both the local and " "peer P-mLACP devices to determine which peer member IP has lost communication. Use this " "information to further debug the network communication issue and re-enable communication " "with the peer. Reference the P-mLACP section of the IOS documentation for more information " "on peer down failures." ETHERNET_PMLACP-4-PEER_DOWN 4-Warning P-mLACP Peer down failure: Attempting to make [dec] local ports active in redundancy group [dec] P-mLACP has detected a peer down failure and has attempted to make the local port-channels become active. lacp "The peer down failure should be corrected by re-enabling communication " "with the peer P-mLACP device. Use the show redundancy interchassis " "command on both the local and peer P-mLACP devices to determine which peer member IP " "has lost communication. Use this information to further debug the network communication " "issue and re-enable communication with the peer. Reference the P-mLACP section of the IOS " "documentation for more information on peer down failures." ETHERNET_PMLACP-4-PEER_RECONNECT_FAILED 4-Warning The attempt to reconnect to the peer in redundancy group [dec] has failed After an P-mLACP peer device disconnected an attempt was made to reconnect however that attempt has failed. lacp "To reinitialize the connection unconfigure mlacp interchassis group " "from the port-channel and then reconfigure it. After doing that issue " "show redundancy interchassis to get the peer member IP " "connection status and the P-mLACP connection state. If the peer member IP " "connection status is not CONNECTED then there is a more basic communication " "issue that needs to be fixed. Otherwise if the peer member IP is CONNECTED but " "the P-mLACP state is not CONNECTED then there could be a software issue. In that " "case collect the output of show redundancy interchassis " "show lacp multi-chassis load-balance group and " "show lacp multi-chassis load-balance port-channel. Then please contact your " "Cisco technical support representative and provide the collected information." ETHERNET_PMLACP-4-PEER_UP 4-Warning P-mLACP has recovered from a peer down failure in redundancy group [dec] P-mLACP is now in communication with the peer device and has recovered from a previous peer down failure. lacp "This message may not require any action. However the " "show lacp multi-chassis load-balance group and " "show lacp multi-chassis load-balance port-channel commands may be used " "to verify the state of the P-mLACP port-channels. Reference the P-mLACP section " "of the IOS documentation for details on peer down failures and related " "configuration commands." ETHERNET_PMLACP-6-PEER_CONNECT 6-Information P-mLACP peer is now connected in redundancy group [dec] This message indicates that the local P-mLACP device is now connected to a peer device in the specified redundancy group. lacp "No action is required. To view the peer information the command " "show lacp multi-chassis load-balance port-channel or " "show lacp multi-chassis load-balance group may be issued." ETHERNET_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical CPP ETHERNET Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. CPP ETHERNET Proxy initialization detected that the IPC interface initialization failed. CPP ETHERNET proxy will not be functional while this condition exists. qfp-bb keyword:none LOG_STD_ACTION ETHERNET_PROXY-3-PROXY_BAD_MSG 3-Error CPP ETHERNET Proxy received bad length message type [dec] Cisco internal software error. CPP ETHERNET Proxy received a corrupted message from control plane. This message will be ignored. qfp-bb keyword:none LOG_STD_ACTION ETHERNET_PROXY-3-PROXY_INV_MSG 3-Error CPP ETHERNET Proxy received invalid message type [dec] Cisco internal software error. CPP ETHERNET Proxy received an invalid message type from control plane. This message will be ignored. qfp-bb keyword:none LOG_STD_ACTION ETHERNET_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error CPP ETHERNET Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. CPP ETHERNET Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ETHERNET_PROXY-3-PROXY_IPC_NO_HDLR 3-Error CPP ETHERNET Proxy received unregistered message type [dec] Cisco internal software error. CPP ETHERNET Proxy received a message from control plane but there is no registered handler. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ETHERNET_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error CPP ETHERNET Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. CPP ETHERNET Proxy message processing detected a message sent failure. The message is lost as the result of this condition. qfp-bb keyword:none LOG_STD_ACTION ETHERNET-1-NOMEMORY 1-Alert msgtxt_nomemory Insufficient memory exists to allocate the necessary memory pools. - "If this message recurs call your technical support representative for assistance." ETHERNET-1-TXERR 1-Alert [chars]: Fatal transmit error. Restarting... A fatal transmit error occurred on the Ethernet line causing the line to be restarted. - "If this message recurs call your technical support representative for assistance." ETHERNET-3-ETHERNET_INIT_FAIL 3-Error Dataplane ETHERNET init error for [chars] Cisco internal software error. This is likely due to a dataplane memory exhaust cpp-ucode keyword:ethernet LOG_STD_ACTION ETHERNET-4-UNSUPINTFC 4-Warning Interface Ethernet[dec] not supported by [chars] image The specific ethernet interface is not supported by the operating system currently running. - "If the hardware configuration is supported by a newer version of the operating system it will be necessary to upgrade the software in order to support this interface." EVENT_TRACE-3-CLOSE_FILE 3-Error Error closing file [chars] The Event Trace subsystem can not close the specified file Trace "No action required. This will not affect " "system functionality" EVENT_TRACE-3-CLOSE_FILE 3-Error Error closing file [chars] The Event Trace subsystem can not close the specified file Trace "No action required. This will not affect " "system functionality" EVENT_TRACE-3-CONTINUOUS 3-Error Enable trace before setting continuous display The specified event trace must be enabled before continuous display could occurs. Trace "Enable the specified event trace." EVENT_TRACE-3-CONTINUOUS 3-Error Enable trace before setting continuous display The specified event trace must be enabled before continuous display could occurs. Trace "Enable the specified event trace." EVENT_TRACE-3-GROUP_ID 3-Error Duplicate registration of group-id [dec] Software subsystem is trying to register a group id for event trace which has already been used by another subsystem. Trace LOG_STD_ACTION EVENT_TRACE-3-GROUP_ID 3-Error Duplicate registration of group-id [dec] Software subsystem is trying to register a group id for event trace which has already been used by another subsystem. Trace LOG_STD_ACTION EVENT_TRACE-3-NO_FILENAME 3-Error Dump file not specified. No filename has been specified as output for the event trace. Trace "You must specify the trace dump filename. To specify the trace dump " "filename enter the monitor event-trace comp dump-file filename command " "in global configuration mode" EVENT_TRACE-3-NO_FILENAME 3-Error Dump file not specified. No filename has been specified as output for the event trace. Trace "You must specify the trace dump filename. To specify the trace dump " "filename enter the monitor event-trace comp dump-file filename command " "in global configuration mode" EVENT_TRACE-3-NO_MEM 3-Error Not enough memory for [dec] trace elements. The system memory is insufficient for the number of trace elements specified. Trace "Reduce the size of the event trace" EVENT_TRACE-3-NO_MEM 3-Error Not enough memory for [dec] trace elements. The system memory is insufficient for the number of trace elements specified. Trace "Reduce the size of the event trace" EVENT_TRACE-3-NO_TRACE_NAME 3-Error Invalid trace name [chars] There is no trace buffer configured by the name entered. Trace "Check whether there is an event trace buffer " "configured by the name entered and then enter the correct trace " "buffer name." EVENT_TRACE-3-NO_TRACE_NAME 3-Error Invalid trace name [chars] There is no trace buffer configured by the name entered. Trace "Check whether there is an event trace buffer " "configured by the name entered and then enter the correct trace " "buffer name." EVENT_TRACE-3-NUM_ELEM 3-Error Number of trace element = [dec] is greater than number = [dec] allowed The number of trace entries exceed the allowed amount Trace "Reduce the number of trace entries" EVENT_TRACE-3-NUM_ELEM 3-Error Number of trace element = [dec] is greater than number = [dec] allowed The number of trace entries exceed the allowed amount Trace "Reduce the number of trace entries" EVENT_TRACE-3-OPEN 3-Error [chars]: Trace failed to open Initialization of the specified event trace has failed. Trace LOG_STD_ACTION EVENT_TRACE-3-OPEN 3-Error [chars]: Trace failed to open Initialization of the specified event trace has failed. Trace LOG_STD_ACTION EVENT_TRACE-3-OPEN_FILE 3-Error Couldn't open [chars]... The Event Trace subsystem could not open a file for the specified event trace dump. Trace "If a file by the same name already exists rename the dump file or " "remove the existing file from the file system." EVENT_TRACE-3-OPEN_FILE 3-Error Couldn't open [chars]... The Event Trace subsystem could not open a file for the specified event trace dump. Trace "If a file by the same name already exists rename the dump file or " "remove the existing file from the file system." EVENT_TRACE-3-RESIZE 3-Error Enable trace before resizing The specified event trace must be enabled before resizing occurs. Trace "Enable the specified event trace." EVENT_TRACE-3-RESIZE 3-Error Enable trace before resizing The specified event trace must be enabled before resizing occurs. Trace "Enable the specified event trace." EVENT_TRACE-3-SIZE_ELEM 3-Error Size of trace element = [dec] is greater than size = [dec] allowed The size of the specified individual trace entry is greater than the allowed size. Trace "Reduce the individual trace entry size so as not " "to exceed the max while initializing the event trace" EVENT_TRACE-3-SIZE_ELEM 3-Error Size of trace element = [dec] is greater than size = [dec] allowed The size of the specified individual trace entry is greater than the allowed size. Trace "Reduce the individual trace entry size so as not " "to exceed the max while initializing the event trace" EVENT_TRACE-3-SIZE_FILENAME 3-Error Trace filename size = [dec] greater than size = [dec] allowed The length of the specified Event Trace filename exceeds the allowed. Trace "Shorten the filename." EVENT_TRACE-3-SIZE_FILENAME 3-Error Trace filename size = [dec] greater than size = [dec] allowed The length of the specified Event Trace filename exceeds the allowed. Trace "Shorten the filename." EVENT_TRACE-3-WRITE_FILE 3-Error Error writing to file [chars] Event trace is not able to write to the specified filesystem Trace "The filesystem might not be available. Try " "changing the destination filesystem and dumping there. " "If none work copy the error message exactly as it and " "call your Cisco technical support representative" EVENT_TRACE-3-WRITE_FILE 3-Error Error writing to file [chars] Event trace is not able to write to the specified filesystem Trace "The filesystem might not be available. Try " "changing the destination filesystem and dumping there. " "If none work copy the error message exactly as it and " "call your Cisco technical support representative" EVENT_TRACE-6-ENABLE 6-Information Trace already enabled. Specified event trace has already been enabled Trace LOG_STD_DBG_ACTION EVENT_TRACE-6-ENABLE 6-Information Trace already enabled. Specified event trace has already been enabled Trace LOG_STD_DBG_ACTION EVENT_TRACE-6-NO_FORMATTER 6-Information [chars]: no formatter provided binary dumping. No formatter function was provided during the initialization of the specified event trace. Trace LOG_STD_NO_ACTION EVENT_TRACE-6-NO_FORMATTER 6-Information [chars]: no formatter provided binary dumping. No formatter function was provided during the initialization of the specified event trace. Trace LOG_STD_NO_ACTION EVENT-3-INSERT_FAILURE 3-Error Failed to insert [chars] The event process failed to insert the newly created row in\n\ its linked list data structure snmp "Copy the error message exactly as it appears and report it to\n\ your technical support representative." EVENT-3-NULL_ELEMENT 3-Error Null pointer in the watched queue for [chars] test The process was woken up with an NULL element snmp "Copy the error message exactly as it appears and report it to\n\ your technical support representative." EVENT-3-NULL_STRUCT 3-Error Null pointer to the [chars] structure The process was woken up with an element which had a null pointer to\n\ the test structure snmp "Copy the error message exactly as it appears and report it to\n\ your technical support representative." EVENTLIB-3-CPUHOG 3-Error [chars]: [dec]ms Traceback=[chars] This error occurs when a particular event consumes an unfair share of the CPU that may degrade overall system response time. asr1k-xe-infra show platform software process event EVENTLIB-3-EVFDREAD 3-Error Event notification read failed with err [chars] This occurs when we fail to read a thread notify event polaris-infra LOG_STD_DDTS_TAC_DETAILS EVENTLIB-3-HISTELEM 3-Error elem[[dec]] event: [chars] [chars] set: %llums unset: %llums hog check: [dec] caller: %p app-info: [chars] This event element is part of a CPUHOG or TIMEHOG error providing diagnostic details useful to engineering. Save all element messages along with the HOG error. mcp-infra LOG_STD_DDTS_TAC_DETAILS EVENTLIB-3-HISTSUMM 3-Error dispatch start: %llums elapsed time: %llums detected hog: [dec] set count: [dec] This event summary is part of a CPUHOG or TIMEHOG error providing diagnostic details useful to engineering. Save this summary message along with the HOG error. mcp-infra LOG_STD_DDTS_TAC_DETAILS EVENTLIB-3-RUNHOG 3-Error [chars]: [dec]ms Traceback=[chars] This error occurs when a particular event consumes an overall unfair share of the CPU that may degrade overall system response time. asr1k-xe-infra show platform software process event EVENTLIB-3-TIMEHOG 3-Error [chars]: %llums Traceback=[chars] This error occurs when a particular event takes an unusually long time to complete. This may affect overall system response time. asr1k-xe-infra show platform software process event EVENTQ-3-LCON 3-Error ERRMSG_NOFLAGS - - - EVENTQ-3-LCON 3-Error ERRMSG_NOFLAGS - - - EVPN-3-CORE_ISOLATION 3-Error Bringing down multi-homing access interface [chars] EVPN is bringing down the multi-homing access interface due to core isolation failure detected. evpn-mgr "Diagnose and recover from core isolation failure then EVPN will bring " "the multi-homing access interface up automatically." EVPN-3-CORE_ISOLATION 3-Error Bringing down multi-homing access interface [chars] EVPN is bringing down the multi-homing access interface due to core isolation failure detected. evpn-mgr "Diagnose and recover from core isolation failure then EVPN will bring " "the multi-homing access interface up automatically." EVPN-3-DUP_IP 3-Error Duplicate IP address [chars] EVI [dec] [chars] [dec] detected on [chars] and [chars] EVPN has detected a duplicate IP address in the network. This occurs when the same IP address is learned from multiple different MAC addresses more than N times within M seconds where N is the configured IP duplication limit which defaults to 5 and M is the configured IP evpn-mgr "Locate and remove the duplicate IP address then use the command " "'clear l2vpn evpn ip duplicate ' to " "resume IP learning for that address." EVPN-3-DUP_IP 3-Error Duplicate IP address [chars] EVI [dec] [chars] [dec] detected on [chars] and [chars] EVPN has detected a duplicate IP address in the network. This occurs when the same IP address is learned from multiple different MAC addresses more than N times within M seconds where N is the configured IP duplication limit which defaults to 5 and M is the configured IP evpn-mgr "Locate and remove the duplicate IP address then use the command " "'clear l2vpn evpn ip duplicate ' to " "resume IP learning for that address." EVPN-3-DUP_MAC 3-Error Duplicate [chars]MAC address [enet] EVI [dec] [chars] [dec] detected on [chars] and [chars] EVPN has detected a duplicate MAC address in the network. This occurs when the same MAC address is learned from both a local port and a remote device more than N times within M seconds where N is the configured MAC duplication limit which defaults to 5 and M is the configured MAC evpn-mgr "Locate and remove the duplicate MAC address then use the command " "'clear l2vpn evpn mac duplicate ' to " "resume MAC learning for that address." EVPN-3-DUP_MAC 3-Error Duplicate [chars]MAC address [enet] EVI [dec] [chars] [dec] detected on [chars] and [chars] EVPN has detected a duplicate MAC address in the network. This occurs when the same MAC address is learned from both a local port and a remote device more than N times within M seconds where N is the configured MAC duplication limit which defaults to 5 and M is the configured MAC evpn-mgr "Locate and remove the duplicate MAC address then use the command " "'clear l2vpn evpn mac duplicate ' to " "resume MAC learning for that address." EVPN-3-ES_ENCAP_MISMATCH 3-Error ES route with encapsulation mismatch received from [chars]/[chars] Local and remote EVPN instances must have the same encapsulation type. evpn-mgr "Correct the configuration by changing the encapsulation type of local " "or remote EVPN instance" EVPN-3-ES_ENCAP_MISMATCH 3-Error ES route with encapsulation mismatch received from [chars]/[chars] Local and remote EVPN instances must have the same encapsulation type. evpn-mgr "Correct the configuration by changing the encapsulation type of local " "or remote EVPN instance" EVPN-3-INCOMPATIBLE_MCAST_GROUP 3-Error Incompatible multicast group configuration for L2 VNI [dec] A Layer 2 VNI used for EVPN must have not an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when ingress replication is configured. evpn-mgr "Correct the configuration by removing the " "mcast-group keyword from the 'member vni' command " "in the NVE interface sub-mode." EVPN-3-INCOMPATIBLE_MCAST_GROUP 3-Error Incompatible multicast group configuration for L2 VNI [dec] A Layer 2 VNI used for EVPN must have not an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when ingress replication is configured. evpn-mgr "Correct the configuration by removing the " "mcast-group keyword from the 'member vni' command " "in the NVE interface sub-mode." EVPN-3-INCOMPATIBLE_REPLICATION 3-Error Incompatible replication configuration for EVI [dec] [chars] [dec] An EVPN instance with MPLS encapsulation must not be configured if the replication type is static. evpn-mgr "Correct the configuration by changing the " "replication type configuration to ingress." EVPN-3-INCOMPATIBLE_REPLICATION 3-Error Incompatible replication configuration for EVI [dec] [chars] [dec] An EVPN instance with MPLS encapsulation must not be configured if the replication type is static. evpn-mgr "Correct the configuration by changing the " "replication type configuration to ingress." EVPN-3-INTERNAL 3-Error Internal error: [chars] An internal software error has occurred. evpn-mgr LOG_STD_ACTION EVPN-3-INTERNAL 3-Error Internal error: [chars] An internal software error has occurred. evpn-mgr LOG_STD_ACTION EVPN-3-MAX_PEERS_EXCEEDED 3-Error Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The newly discovered peer will not be added to the peer list so as not to impact current peering and designated forwarder election results. evpn-mgr "Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised." EVPN-3-MAX_PEERS_EXCEEDED 3-Error Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The newly discovered peer will not be added to the peer list so as not to impact current peering and designated forwarder election results. evpn-mgr "Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised." EVPN-3-MAX_PEERS_EXCEEDED_ES_DISABLED 3-Error Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The Ethernet Segment will be disabled. evpn-mgr "Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised." EVPN-3-MAX_PEERS_EXCEEDED_ES_DISABLED 3-Error Maximum number of peers [dec] exceeded for Ethernet Segment [chars] in EVPN has received a peer nexthop update from BGP which would push the number of peers in the Ethernet Segment past the supported limit for single-active redundancy mode. The Ethernet Segment will be disabled. evpn-mgr "Take one of the PE's out of the Ethernet Segment by modifying or " "removing its ESI configuration. If it's a PE already peering need to " "toggle the access interface or reconfigure ESI on the newly discovered " "peer to ensure it is re-advertised." EVPN-3-MISSING_MCAST_GROUP 3-Error Missing multicast group configuration for L2 VNI [dec] A Layer 2 VNI used for EVPN must have an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when static replication is configured. evpn-mgr "Correct the configuration by adding the " "mcast-group keyword to the 'member vni' command " "in the NVE interface sub-mode." EVPN-3-MISSING_MCAST_GROUP 3-Error Missing multicast group configuration for L2 VNI [dec] A Layer 2 VNI used for EVPN must have an associated multicast group for Broadcast Unknown Unicast and Multicast traffic when static replication is configured. evpn-mgr "Correct the configuration by adding the " "mcast-group keyword to the 'member vni' command " "in the NVE interface sub-mode." EVPN-3-UNSUPPORTED_MIX_ENCAP 3-Error EVIs with different encapsulation types are not supported in the same Ethernet Segment[[chars]] All EVPN instances associated with an Ethernet Segment must have the same encapsulation type. evpn-mgr "Correct the configuration by changing the encapsulation type of the " "EVPN instances associated with the Ethernet Segment to be the same." EVPN-3-UNSUPPORTED_MIX_ENCAP 3-Error EVIs with different encapsulation types are not supported in the same Ethernet Segment[[chars]] All EVPN instances associated with an Ethernet Segment must have the same encapsulation type. evpn-mgr "Correct the configuration by changing the encapsulation type of the " "EVPN instances associated with the Ethernet Segment to be the same." EVPN-5-AA_IRB_TRAFFIC_MAY_DROP 5-Notice Traffic may drop on the CE side depending on the CE behavior On the CE side traffic may drop depending on the CE behavior traffic could be hashed to a specific link in the MC-LAG group. evpn-mgr LOG_STD_NO_ACTION EVPN-5-AA_IRB_TRAFFIC_MAY_DROP 5-Notice Traffic may drop on the CE side depending on the CE behavior On the CE side traffic may drop depending on the CE behavior traffic could be hashed to a specific link in the MC-LAG group. evpn-mgr LOG_STD_NO_ACTION EVPN-5-CORE_CONNECTED 5-Notice Bringing up multi-homing access interface [chars] EVPN has recovered from a core isolation failure and is bringing up the multi-homing access interface. evpn-mgr LOG_STD_NO_ACTION EVPN-5-CORE_CONNECTED 5-Notice Bringing up multi-homing access interface [chars] EVPN has recovered from a core isolation failure and is bringing up the multi-homing access interface. evpn-mgr LOG_STD_NO_ACTION EVPN-5-DUP_CLEAR_IP 5-Notice Cleared duplicate IP address [chars] EVI [dec] [chars] [dec] EVPN has cleared the duplicate condition on a IP address that was previously detected as a duplicate. evpn-mgr LOG_STD_NO_ACTION EVPN-5-DUP_CLEAR_IP 5-Notice Cleared duplicate IP address [chars] EVI [dec] [chars] [dec] EVPN has cleared the duplicate condition on a IP address that was previously detected as a duplicate. evpn-mgr LOG_STD_NO_ACTION EVPN-5-DUP_CLEAR_MAC 5-Notice Cleared duplicate MAC address [enet] EVI [dec] [chars] [dec] EVPN has cleared the duplicate condition on a MAC address that was previously detected as a duplicate. evpn-mgr LOG_STD_NO_ACTION EVPN-5-DUP_CLEAR_MAC 5-Notice Cleared duplicate MAC address [enet] EVI [dec] [chars] [dec] EVPN has cleared the duplicate condition on a MAC address that was previously detected as a duplicate. evpn-mgr LOG_STD_NO_ACTION EVPN-5-ES_LOCAL_RED_MOD_CHANGE_NOT_ALLOWED 5-Notice Local redundancy mode change is not allowed for Ethernet Segment [chars] because it has two or more forwarders. Local redundancy mode change is not allowed for Ethernet Segments with two or more forwarders. Configuration is updated while local redundancy mode is kept unchanged. Local redundancy mode will be updated when the number of forwarders drops to less than two. evpn-mgr "Reduce the number of forwarders to less than two to allow local " "redundancy mode change." EVPN-5-ES_LOCAL_RED_MOD_CHANGE_NOT_ALLOWED 5-Notice Local redundancy mode change is not allowed for Ethernet Segment [chars] because it has two or more forwarders. Local redundancy mode change is not allowed for Ethernet Segments with two or more forwarders. Configuration is updated while local redundancy mode is kept unchanged. Local redundancy mode will be updated when the number of forwarders drops to less than two. evpn-mgr "Reduce the number of forwarders to less than two to allow local " "redundancy mode change." EVPN-5-ES_LOCAL_RED_MOD_CHANGED 5-Notice Local redundancy mode has been changed to [chars] for Ethernet Segment [chars]. An event has occurred that has caused local redundancy mode to change. evpn-mgr LOG_STD_NO_ACTION EVPN-5-ES_LOCAL_RED_MOD_CHANGED 5-Notice Local redundancy mode has been changed to [chars] for Ethernet Segment [chars]. An event has occurred that has caused local redundancy mode to change. evpn-mgr LOG_STD_NO_ACTION EVPN-5-L3RIB_CONFLICT 5-Notice Detected a static route already installed for VRF ID destination IP [%lu [chars]] with full prefix length. EVPN will install a static route which may be overridden in RIB by the other static route. EVPN installs a static route for learned local and proxy MAC/IPs with the IP as the destination prefix and full prefix length. A static route matching this has already been installed either by the configuration CLI or another application owner. The EVPN one is installed with lower administrative distance and may be overridden by routes with the same prefix length. evpn-mgr "If an IPv4 or IPv6 static route for this VRF prefix and full prefix " "length has been configured intentionally this message can be ignored. " "If not intentionally remove the configuration so that the EVPN RIB " "entries can be activated." EVPN-5-L3RIB_CONFLICT 5-Notice Detected a static route already installed for VRF ID destination IP [%lu [chars]] with full prefix length. EVPN will install a static route which may be overridden in RIB by the other static route. EVPN installs a static route for learned local and proxy MAC/IPs with the IP as the destination prefix and full prefix length. A static route matching this has already been installed either by the configuration CLI or another application owner. The EVPN one is installed with lower administrative distance and may be overridden by routes with the same prefix length. evpn-mgr "If an IPv4 or IPv6 static route for this VRF prefix and full prefix " "length has been configured intentionally this message can be ignored. " "If not intentionally remove the configuration so that the EVPN RIB " "entries can be activated." EVPN-5-PEER_STATUS 5-Notice Peer [chars] [chars] is [chars] An event has occurred that has caused the peer to change status evpn-mgr LOG_STD_NO_ACTION EVPN-5-PEER_STATUS 5-Notice Peer [chars] [chars] is [chars] An event has occurred that has caused the peer to change status evpn-mgr LOG_STD_NO_ACTION EVPN-5-VC_STATUS 5-Notice EVPN[[dec] [dec]/[dec]]: VC state [chars] An event has occurred that has caused the vc to change status evpn-mgr LOG_STD_NO_ACTION EVPN-5-VC_STATUS 5-Notice EVPN[[dec] [dec]/[dec]]: VC state [chars] An event has occurred that has caused the vc to change status evpn-mgr LOG_STD_NO_ACTION EVTMON_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. qfp-evtmon LOG_STD_ACTION EVTMON_PROXY-4-PROXY_IPC_EVTMON_FEAT_UPDATE_FAILED 4-Warning feature user failed to [chars] because of [chars] Event monitor feature user failed to attach or detach. qfp-evtmon LOG_STD_ACTION EVTMON_PROXY-4-PROXY_IPC_EVTMON_REC_UPDATE_FAILED 4-Warning event record update failed Event monitor failed to attach or detach event record. qfp-evtmon LOG_STD_ACTION EVTMON_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. qfp-evtmon LOG_STD_ACTION EWLC_CAPWAP_IDB-3-IFINDEX_ZERO 3-Error [chars] : ifindex is zero for interface [chars]. Unit : [dec] Slot : [dec] IFINDEX of a capwap idb is zero. - "show idb" EWLC_L2_ISSU-3-BUFFER 3-Error EWLC L2 ISSU client failed to get buffer for message error [dec] EWLC L2 ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. platform-ha "show logging and show checkpoint client" EWLC_L2_ISSU-3-CAP_INVALID_SIZE 3-Error EWLC L2 ISSU client capability list is empty. The EWLC L2 ISSU client capability exchange list size\n\ is invalid. platform-ha "show issu capability entries " EWLC_L2_ISSU-3-CAP_NOT_COMPATIBLE 3-Error EWLC L2 ISSU client capability exchange result incompatible. The EWLC L2 ISSU client capability exchange has negotiated\n\ as incompatible with the peer. platform-ha "show issu negotiated capability " EWLC_L2_ISSU-3-CAPABILITY 3-Error EWLC L2 ISSU client [chars] EWLC L2 ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit. platform-ha "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " EWLC_L2_ISSU-3-INIT 3-Error EWLC L2 ISSU client initialization failed at [chars] error [chars] EWLC L2 ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2_ISSU-3-MSG_NOT_OK 3-Error EWLC L2 ISSU client message [dec] is not compatible EWLC L2 ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit platform-ha "show issu message group and\n\ show issu session and\n\ show issu negotiated version " EWLC_L2_ISSU-3-MSG_SIZE 3-Error EWLC L2 ISSU client failed to get the message size for message [dec] EWLC L2 ISSU client failed to calculate message size\n\ for the message specified. The EWLC L2 ISSU client will not\n\ be able to send message to the standby unit. platform-ha "show issu message group and\n\ show issu session and\n\ show issu negotiated version " EWLC_L2_ISSU-3-POLICY 3-Error EWLC L2 ISSU client message type [dec] is [chars] EWLC L2 ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible. platform-ha "show issu session " EWLC_L2_ISSU-3-SEND_FAILED 3-Error EWLC L2 ISSU client failed to send a negotiation message error [dec] EWLC L2 ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up. platform-ha "show logging and show checkpoint client" EWLC_L2_ISSU-3-SESSION 3-Error EWLC L2 ISSU client [chars] EWLC L2 ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up. platform-ha "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " EWLC_L2_ISSU-3-SESSION_UNREGISTRY 3-Error EWLC L2 ISSU client failed to unregister session information. Error: [dec] [chars] The EWLC L2 ISSU client failed to unregister session information. platform-ha "show issu session and " "show issu negotiated capability " EWLC_L2_ISSU-3-TRANSFORM 3-Error EWLC L2 ISSU client [chars] transform failed error [chars] EWLC L2 ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the EWLC L2 state will not\n\ be indentical with the active unit. platform-ha "show issu session and\n\ show issu negotiated version " EWLC_L2-3-BULK_SYNC 3-Error [chars] Bulk sync failure the reason for the failure will be provided in the string platform-ha "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." EWLC_L2-3-FILE_OPEN_FAILURE 3-Error File [chars] open failed File Open failed platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2-3-INVALID_MSG_RECEIVED 3-Error Invalid [chars] message received A message that is used for state synchronization was not received correctly. An internal data structure for a message could not be retrieved. The failure most likely occurred because of a software error. The system state between the active and standby units might not be properly synchronized. platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2-3-MAC_FAILURE 3-Error Mac Failure NULL MAC platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2-3-MALLOC_FAILURE 3-Error [chars] Failed to allocated memory for a structure or event platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2-3-OIR_FAILURE 3-Error Message:[chars]Error:[dec] EWLC L2 failures due to various reasons platform-ha LOG_STD_SH_TECH_ACTION EWLC_L2-3-REG_FAILURE 3-Error Message:[chars]Error:[dec] Registration Failure platform-ha LOG_STD_SH_TECH_ACTION EWLC_PLATFORM-3-PROCESS_CREATE_FAILED 3-Error System resource check failed. System resource check failed. System could be running on unsupported hardware resources - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_CREATE 4-Warning Creating fips objstore key failed [chars] FIPS objstore key create failed - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_DELETE 4-Warning Deleting fips objstore key failed [chars] FIPS objstore key delete failed - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_OPEN 4-Warning Opening fips objstore key failed [chars] FIPS Objstore key could not be opened. - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_READ 4-Warning Reading fips objstore key failed [chars] FIPS objstore key could not be read - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_READ_INCORRECT_LEN 4-Warning Reading of objstore key failed due to incorrect length [dec] [dec] FIPS objstore key read failed - LOG_STD_NO_ACTION EWLC_PLATFORM-4-FIPS_OBJSTORE_WRITE 4-Warning Writing fips objstore key failed [chars] FIPS objstore key write failed - LOG_STD_NO_ACTION EWLC_PLATFORM-4-REC_CPU 4-Warning System is running with CPUs lower than recommended. Current no of CPUs: [dec] Recommended no of CPUs: [dec] System is running with CPUs lower than recommended. Please refer to release notes. - LOG_STD_NO_ACTION EWLC_PLATFORM-4-REC_DISK 4-Warning System is running on a disk lower than recommended. Current Disk Size: [dec]GB Recommended Disk Size: [dec]GB System is running on a disk lower than recommended. Please refer to release notes. - LOG_STD_NO_ACTION EWLC_PLATFORM-4-REC_MEM 4-Warning System is running with memory lower than recommended. Current Memory: [dec]GB Recommended Memory: [dec]GB System is running with memory lower than recommended. Please refer to release notes. - LOG_STD_NO_ACTION EWLC_PLATFORM-4-UNKNOWN_EVENT 4-Warning Unknown event [dec] [dec] Unknown event occurred. - LOG_STD_NO_ACTION EWLC_PLATFORM-5-EWC_MESH_DAY0_CONVERSION 5-Notice Conversion of internal AP to bridge mode in progress: [chars] The AP mode change steps will be executed once the AP completes day-0 initialization. - LOG_STD_NO_ACTION EXAR7503-3-EXAR7503_INIT_ERR 3-Error Exar7503 LIU channel:[dec] init error Error present during Exar LIU initialization osm-ct3 for CT3 osm-t3e3 for T3/E3 LOG_STD_ACTION EXAR7503-3-EXAR7503_NUM_ERR 3-Error INvalid Exar7503 LIU number error: [chars] Error present while inavlid EXAR number present osm-ct3 for CT3 osm-t3e3 for T3/E3 LOG_STD_ACTION EXAR7503-3-EXAR7503_PROG_ERR 3-Error Exar7503 LIU programming error: [chars] Error present while read/write to Exar LIU osm-ct3 for CT3 osm-t3e3 for T3/E3 LOG_STD_ACTION EXFREE-2-EXMEMFREE 2-Critical Free a non allocated ptr [hec] size [dec]. Trying to free a memory which not all of it marked as allocated. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMFREE 2-Critical Free a non allocated ptr [hec] size [dec]. Trying to free a memory which not all of it marked as allocated. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMINIT 2-Critical EXMEM [dec]: [chars] The requested external memory allocator failed to be initialized.\n\ Reasons are not clear. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMINIT 2-Critical EXMEM [dec]: [chars] The requested external memory allocator failed to be initialized.\n\ Reasons are not clear. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMLOCK 2-Critical [chars] detected error ptr [hec] size [dec]. Attempting to lock or unlock a memory location which was\n\ either already locked or unlocked. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMLOCK 2-Critical [chars] detected error ptr [hec] size [dec]. Attempting to lock or unlock a memory location which was\n\ either already locked or unlocked. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMPARAM 2-Critical Bad parameter [dec] when calling to the allocator utility Illegal parameter is used when called to allocator. may represent \n\ data some corruption. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMPARAM 2-Critical Bad parameter [dec] when calling to the allocator utility Illegal parameter is used when called to allocator. may represent \n\ data some corruption. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMRESET 2-Critical EXMEM [dec]: [chars] The requested external memory allocator failed to be reset.\n\ Reasons are not clear. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-2-EXMEMRESET 2-Critical EXMEM [dec]: [chars] The requested external memory allocator failed to be reset.\n\ Reasons are not clear. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-4-EXMALLOCFAIL 4-Warning External memory allocation of [dec] bytes failed from EXMEM [dec] The requested memory allocation is not available from the specified\n\ memory pool. The current system configuration network environment or\n\ possibly a software error might have exhausted or fragmented the\n\ router's memory. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXFREE-4-EXMALLOCFAIL 4-Warning External memory allocation of [dec] bytes failed from EXMEM [dec] The requested memory allocation is not available from the specified\n\ memory pool. The current system configuration network environment or\n\ possibly a software error might have exhausted or fragmented the\n\ router's memory. mem "Copy the error message exactly as it appears and report it to your\n\ technical support representative." EXPRESS_SETUP-3-UNABLE_TO_RESET_CONFIG 3-Error [chars] The system is unable to reset the configuration firmware LOG_STD_ACTION EXPRESS_SETUP-5-CONFIG_IS_RESET 5-Notice [chars] The configuration is reset and the system will now reboot firmware LOG_STD_ACTION EXPRESS_SETUP-6-MODE_BUTTON_RESET_IGNORED 6-Information [chars] mode button pressed for more than 10Sec and startup config is present hence not reloading firmware LOG_NO_ACTION EXPRESS_SETUP-6-MODE_ENTERED 6-Information - Express setup mode is now active firmware LOG_NO_ACTION EXPRESS_SETUP-6-MODE_EXITED 6-Information - Express setup mode is no longer active firmware LOG_NO_ACTION EXPRESSION-3-BADTYPE 3-Error Found data type [hec] in expression should be [chars] type While evaluating an expression an operand was found with an unexpected\n\ datatype. Evaluation of this expression has been aborted. snmp "Copy the error message exactly as it appears and report it to\n\ your technical support representative." EXPRESSION-3-FAILASSERT 3-Error Assertion failed: [chars] An operation within the Expression MIB subsystem encountered\n\ a data value that is out of range or of an unexpected value\n\ indicative of a logic error within the subsystem. snmp "Copy the error message exactly as it appears and report it to\n\ your technical support representative." EXTASSIGNER-3-ERRSYNC 3-Error \ Failed to sync tag[dec] to standby CME\n - - - EXTASSIGNER-3-ERRSYNC 3-Error \ Failed to sync tag[dec] to standby CME\n - - - EXTASSIGNER-3-ERRSYNC2 3-Error \ Failed to sync re-assign tag [dec] for [dec] to standby CME\n - - - EXTASSIGNER-3-ERRSYNC2 3-Error \ Failed to sync re-assign tag [dec] for [dec] to standby CME\n - - - EXTASSIGNER-3-ERRTAG 3-Error \ Invalid tag[dec]\n - - - EXTASSIGNER-3-ERRTAG 3-Error \ Invalid tag[dec]\n - - - EXTASSIGNER-3-NOACTPHONE 3-Error \ Failed to find the calling phone\n - - - EXTASSIGNER-3-NOACTPHONE 3-Error \ Failed to find the calling phone\n - - - EXTASSIGNER-3-NOCB 3-Error \ Failed to find the skinnyCB\n - - - EXTASSIGNER-3-NOCB 3-Error \ Failed to find the skinnyCB\n - - - EXTASSIGNER-3-NOMEM 3-Error \ Failed to malloc\n - - - EXTASSIGNER-3-NOMEM 3-Error \ Failed to malloc\n - - - EXTASSIGNER-3-NULLPTR 3-Error \ Null pointer [chars]:[dec]\n - - - EXTASSIGNER-3-NULLPTR 3-Error \ Null pointer [chars]:[dec]\n - - - EXTASSIGNER-6-ASSIGNED 6-Information \ Extension assignment successful for phone:SEP[chars]. New pool[dec]. \ Successfully assigned the pool - LOG_STD_NO_ACTION EXTASSIGNER-6-ASSIGNED 6-Information \ Extension assignment successful for phone:SEP[chars]. New pool[dec]. \ Successfully assigned the pool - LOG_STD_NO_ACTION EXTASSIGNER-6-UNASSIGNED 6-Information \ Extension unassignment successful for phone:SEP[chars]. \ Unassigned pool[dec].\n Successfully unassigned the pool - LOG_STD_NO_ACTION EXTASSIGNER-6-UNASSIGNED 6-Information \ Extension unassignment successful for phone:SEP[chars]. \ Unassigned pool[dec].\n Successfully unassigned the pool - LOG_STD_NO_ACTION Failed to send APS command [hec] to [chars] retcode [hec] APS command sending failed c7600-sip-200 "This is a internal software error. If this " "error happened while configuring APS try " "reconfiguring the interface. If the error " "persists or occurred during normal operation " "decode the traceback and " LOG_STD_ACTION - - FALLBACK-3-CACHE_FULL 3-Error Function name [chars]: Cache is full Fallback cache has overflowed and unable to dump entries - "Increase the fallback cache size." FALLBACK-3-CACHE_FULL 3-Error Function name [chars]: Cache is full Fallback cache has overflowed and unable to dump entries - "Increase the fallback cache size." FALLBACK-3-INTERNAL_ERROR 3-Error [chars]: Internal error. An internal error occured. - LOG_STD_NO_ACTION FALLBACK-3-INTERNAL_ERROR 3-Error [chars]: Internal error. An internal error occured. - LOG_STD_NO_ACTION FALLBACK-3-MALLOC_FAIL 3-Error [chars]: Memory allocation failed. Allocation of memory failed. This is possibly due to the fact that system memory pool is exhausted. - LOG_STD_NO_ACTION FALLBACK-3-MALLOC_FAIL 3-Error [chars]: Memory allocation failed. Allocation of memory failed. This is possibly due to the fact that system memory pool is exhausted. - LOG_STD_NO_ACTION FALLBACK-3-NO_RTP_PORT 3-Error Function name [chars]: No available RTP ports. No available voice RTP ports were found. - LOG_STD_NO_ACTION FALLBACK-3-NO_RTP_PORT 3-Error Function name [chars]: No available RTP ports. No available voice RTP ports were found. - LOG_STD_NO_ACTION FALLBACK-3-NO_STATS 3-Error [chars]: No stats were returned.\n No statistic information was returned with probe - LOG_STD_NO_ACTION FALLBACK-3-NO_STATS 3-Error [chars]: No stats were returned.\n No statistic information was returned with probe - LOG_STD_NO_ACTION FALLBACK-3-PROBE_FAILURE 3-Error A probe error to [inet] occured - [chars] A probe error occured. Possibly responder on remote router is not enabled or no machine is on specified IP - "Check the destination router." FALLBACK-3-PROBE_FAILURE 3-Error A probe error to [inet] occured - [chars] A probe error occured. Possibly responder on remote router is not enabled or no machine is on specified IP - "Check the destination router." FALLBACK-3-RTR_CREATE_FAIL 3-Error [chars]: Creation of probe failed. Return code [dec] An RTR probe could no be created. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-3-RTR_CREATE_FAIL 3-Error [chars]: Creation of probe failed. Return code [dec] An RTR probe could no be created. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-3-RTR_START_FAIL 3-Error [chars]: probe could not be started. Return code [dec] An RTR probe could no be started. This can cause inaccurate delay/loss/jitter and icpif values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-3-RTR_START_FAIL 3-Error [chars]: probe could not be started. Return code [dec] An RTR probe could no be started. This can cause inaccurate delay/loss/jitter and icpif values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-3-RTR_STATS_FAIL 3-Error [chars]: Could not retrive statistics from the probe. Return code [dec] \n Could not retrive RTR statistics from the probe. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-3-RTR_STATS_FAIL 3-Error [chars]: Could not retrive statistics from the probe. Return code [dec] \n Could not retrive RTR statistics from the probe. This can cause inaccurate ICPIF values and cause VoIP calls to be hairpined when they should not - LOG_STD_NO_ACTION FALLBACK-4-CACHE_OVERFLOW 4-Warning Function name [chars]: Cache has overflowed. Fallback cache has overflowed and dumped 1/4 of the entries. - "Increase the fallback cache size." FALLBACK-4-CACHE_OVERFLOW 4-Warning Function name [chars]: Cache has overflowed. Fallback cache has overflowed and dumped 1/4 of the entries. - "Increase the fallback cache size." FALLBACK-5-AVBO_PROBE 5-Notice A probe to [inet] is [chars] - codec [chars] icpif [dec] loss [dec] delay [dec] AVBO rtr proble status change. - "use the grace_period option to avoid trasit error" FALLBACK-5-AVBO_PROBE 5-Notice A probe to [inet] is [chars] - codec [chars] icpif [dec] loss [dec] delay [dec] AVBO rtr proble status change. - "use the grace_period option to avoid trasit error" FALLBACK-5-TEST_PROBE_ALREADY_RUNNING 5-Notice A test probe is already running. Only one test probe may run at a time. - "Wait until the first test probe is finished." FALLBACK-5-TEST_PROBE_ALREADY_RUNNING 5-Notice A test probe is already running. Only one test probe may run at a time. - "Wait until the first test probe is finished." FARM_DSPRM-4-NOC5510WARN 4-Warning dsp service dspfarm can not be configured for this card type. There is C549 NM-HDV card configured for dspfarm service.\n\ Only one dspfarm card type is allowed. - "If C5510 card type dspfarm is desired then remove C549 NM-HDV dspfarm \n\ service and reconfigure dspfarm service for this card. " FARM_DSPRM-4-NOC5510WARN 4-Warning dsp service dspfarm can not be configured for this card type. There is C549 NM-HDV card configured for dspfarm service.\n\ Only one dspfarm card type is allowed. - "If C5510 card type dspfarm is desired then remove C549 NM-HDV dspfarm \n\ service and reconfigure dspfarm service for this card. " FARM_DSPRM-4-NOC5510WARN 4-Warning dsp service dspfarm can not be configured for this card type. There is C549 NM-HDV card configured for dspfarm service.\n\ Only one dspfarm card type is allowed. - "If C5510 card type dspfarm is desired then remove C549 NM-HDV dspfarm \n\ service and reconfigure dspfarm service for this card. " FARM_DSPRM-6-CALLDROPINFO 6-Information dspfarm active calls on this card dsp [dec] channel [dec] will be dropped. The card has been removed. Dspfarm active calls on this card\n\ will be dropped. - "No action is required." FARM_DSPRM-6-CALLDROPINFO 6-Information dspfarm active calls on this card dsp [dec] channel [dec] will be dropped. The card has been removed. Dspfarm active calls on this card\n\ will be dropped. - "No action is required." FARM_DSPRM-6-CALLDROPINFO 6-Information dspfarm active calls on this card dsp [dec] channel [dec] will be dropped. The card has been removed. Dspfarm active calls on this card\n\ will be dropped. - "No action is required." FARM_DSPRM-6-CARDINSERTINFO 6-Information dspfarm card slot [dec] is inserted. dspfarm card type is inserted into the slot. - "No action is required." FARM_DSPRM-6-CARDINSERTINFO 6-Information dspfarm card slot [dec] is inserted. dspfarm card type is inserted into the slot. - "No action is required." FARM_DSPRM-6-CARDINSERTINFO 6-Information dspfarm card slot [dec] is inserted. dspfarm card type is inserted into the slot. - "No action is required." FARM_DSPRM-6-CARDREMOVEINFO 6-Information dspfarm card slot [dec] is removed. dspfarm card type is remvoed from the slot. - "No action is required." FARM_DSPRM-6-CARDREMOVEINFO 6-Information dspfarm card slot [dec] is removed. dspfarm card type is remvoed from the slot. - "No action is required." FARM_DSPRM-6-CARDREMOVEINFO 6-Information dspfarm card slot [dec] is removed. dspfarm card type is remvoed from the slot. - "No action is required." FASTBLK-4-CREATE_ERR 4-Warning Fastblk pool creation error: [chars] An unexpected error occurred while performing a fastblk memory\n\pool creation operation slb LOG_STD_RECUR_ACTION FASTBLK-4-DEALLOC_ERR 4-Warning Fastblk deallocation error: [chars] An unexpected error occurred while performing a fastblk memory\n\deallocation operation slb LOG_STD_RECUR_ACTION FASTBLK-4-GROW_ERR 4-Warning Fastblk pool growth error: [chars] An unexpected error occurred while performing a fastblk memory\n\pool growth operation slb LOG_STD_RECUR_ACTION FASTBLK-4-QUEUE_ERR 4-Warning Fastblk queue error: [chars] An unexpected error occurred while performing a fastblk memory\n\queue operation slb LOG_STD_RECUR_ACTION FASTBLK-4-SHRINK_ERR 4-Warning Fastblk pool shrink error: [chars] An unexpected error occurred while performing a fastblk memory\n\pool shrink operation slb LOG_STD_RECUR_ACTION FASTBLK-4-WARNING 4-Warning Unexpected condition: [chars] An unexpected condition was detected while performing a fastblk memory\n\operation slb LOG_STD_RECUR_ACTION FASTHELLO-2-FH_DOWN 2-Critical Fast-Hello interface [chars] lost dual-active detection capability\n FASTHELLO STATUS CHANGED to DOWN with more detail status cat4k-vss LOG_STD_NO_ACTION FASTHELLO-3-FH_MANAGED_CHUNK_FAILED 3-Error Unable to create managed chunk\[chars]\ Unable to create the specified watched boolean due to unknown reasons cat4k-vss LOG_STD_NO_ACTION FASTHELLO-3-FH_QUEUE_CREATE_FAILED 3-Error Unable to create watched queue \[chars]\ Unable to create the specified watched queue because of unknown reasons cat4k-vss LOG_STD_NO_ACTION FASTHELLO-3-REGISTRY_ADD_ERR 3-Error Failure in adding to [chars] registry Could not add a function to the registry cat4k-vss LOG_STD_NO_ACTION FASTHELLO-5-FH_DUAL_ACTIVE_CAP 5-Notice Fast-Hello interface [chars] became dual-active detection capable\n FASTHELLO STATUS became dual-active detection capable with more detail status cat4k-vss LOG_STD_NO_ACTION FASTHELLO-5-FH_UP 5-Notice Fast-Hello interface [chars] status changed to link up\n FASTHELLO STATUS CHANGED to UP with more detail status cat4k-vss LOG_STD_NO_ACTION FASTHELLO-6-FH_BAD_CONFIG 6-Information Fast-hello PDU received on unconfigured interface. Peer_slot: [dec]Peer_port: [dec] Informational messages regarding the configuration of the dual-active fast-hello interface cat4k-vss "Investigate and correct this misconfiguration" FASTHELLO-6-FH_DIFF_DOMAIN 6-Information Fast-hello PDU received from different domain. Peer_slot: [dec]Peer_port: [dec] Informational messages regarding the configuration of the dual-active fast-hello interface cat4k-vss "Investigate and correct this misconfiguration" FASTHELLO-6-FH_SAME_SWITCH 6-Information Fast-hello PDU received from interface configured on same switch. Slot: [dec]Port: [dec] Informational messages regarding the configuration of the dual-active fast-hello interface cat4k-vss "Investigate and correct this misconfiguration" FASTHELLO-6-FH_VERSION_MISMATCH 6-Information Local switch protocol version :[dec] Peer switch protocol version : [dec] Informational messages regarding the software versions running on the switch cat4k-vss LOG_STD_ACTION FB_COREDUMP-3-NOMEMORY 3-Error No Memory or buffer for [chars] to be send to [dec] Sufficient memory was unavailble for Router Shelf to send any command or \n\ acknowledment to the feature boards. - LOG_STD_ACTION FDDI-1-NOMEMORY 1-Alert msgtxt_nomemory - mid-fddi "Copy the error message exactly as it appears and report it to your\n\ technical support representative." FDDI-3-BADSLOT 3-Error Unit [dec] Slot [dec] does not exist. The main processor detects an invalid slot location for one of the\n\ network interface cards. This should never happen. mid-fddi "Call your technical support representative about obtaining a\n\ replacement card." FDDI-3-BADUNIT 3-Error msgtxt_badunit This error message is displayed when the system cannot find\n\ the chipset registers where it expects them to be.\n\ This is most likely a hardware error. mid-fddi LOG_STD_SH_TECH_ACTION FDDI-3-FDDIFAIL 3-Error Interface [chars] [chars] [chars] = [hex] The FDDI interface failed. mid-fddi "Save the output of the error message and call your technical support\n\ representative for assistance." FDDI-3-FDDIFAIL2 3-Error Interface [chars] [chars] [chars] = [hex] [chars] = [hex] The FDDI interface failed. This is the second line of the preceding\n\ FDDIFAIL message. This line contains debug information. mid-fddi "Save the output of the error message and call your technical support\n\ representative for assistance." FDDI-3-NOCAM 3-Error Unit [dec] No CAM exists for this interface. A hardware or software error occurred. mid-fddi "Copy the error message exactly as it appears and report it to your\n\ technical support representative." FEC_ISSU-3- BUFFER 3-Error FEC ISSU client failed to get buffer for message error [dec] FEC ISSU client failed to get buffer for building a negotiation message. Hence it can send the negotiation message to the standby unit. When there is a problem in the negotiaiton the standby unit can not be brought up. L2 "show logging and show checkpoint client" FEC_ISSU-3- CAPABILITY 3-Error FEC ISSU client [chars] FEC SWITCH ISSU client observed an error during capability negotiaiton. When this error happens there is a mismatch between the client capability between the active and standby unit. L2 "show issu capability entries and " "show issu session and " "show issu negotiated capability " FEC_ISSU-3- INIT 3-Error FEC ISSU client initialization failed at [chars] error [chars] FEC ISSU client could not be initiailzed this will cause catstrophic failure when ISSU upgrade or downgrade is performed. L2 LOG_STD_SH_TECH_ACTION FEC_ISSU-3- MSG_NOT_OK 3-Error FEC ISSU client message [dec] is not compatible FEC ISSU client received an incompatible message from the peer unit. Since the message is not compatible it can be processed by this unit L2 "show issu message group and " "show issu session and " "show issu negotiated version " FEC_ISSU-3- MSG_SIZE 3-Error FEC ISSU client failed to get the message size for message [dec] FEC ISSU client failed to calculate message size for the message specified. The OIR ISSU client will not be able to send message to the standby unit. L2 "show issu message group and " "show issu session and " "show issu negotiated version " FEC_ISSU-3- POLICY 3-Error FEC ISSU client message type [dec] is [chars] FEC ISSU client received an message type which it does not support. The policy is applied to make the session compatible. L2 "show issu session " FEC_ISSU-3- SEND_FAILED 3-Error FEC ISSU client failed to send a negotiation message error [dec] FEC ISSU client could not send a session negotiation message to the peer. When there is a problem in the negotiation the standby unit can not be brought up. L2 "show logging and show checkpoint client" FEC_ISSU-3-SESSION 3-Error FEC ISSU client [chars] FEC ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up. L2 "show issu capability entries and " "show issu session and " "show issu negotiated capability " FEC_ISSU-3- SESSION_UNREGISTRY 3-Error FEC ISSU client failed to unregister session information. Error: [dec] [chars] The FEC ISSU client failed to unregister session information. L2 "show issu session and " "show issu negotiated capability " FEC_ISSU-3- TRANSFORM 3-Error FEC ISSU client [chars] transform failed error [chars] FEC ISSU client could not transform the message. If the transmit transformation failed it means that the checkpoint message can not be sent to the standby unit. If the receive transformation failed it means that the checkpoint message can not be applied on the standby unit. In both cases the FEC state will not be indentical with the active unit. L2 "show issu session and " "show issu negotiated version " FFP_HW_IRQ-3-NON_FATAL_INTERRUPT 3-Error %lu errors in the last %lu seconds Accumulation of Cavium hardware-generated error cpp-ucode LOG_STD_ACTION FFP_HW_IRQ-3-TOO_MANY_NON_FATAL_INTERRUPTS 3-Error - Aborting due to too many Cavium hardware-generated errors cpp-ucode LOG_STD_ACTION FGPT-3-INCONSISTENT_FGPT 3-Error [container fingerprint: [chars]] [nvram fingerprint: [chars]] [chars] Fingerprint inconsistency is detected between the license file in this VM and nvram configuration virt-infra LOG_STD_NO_ACTION FGPT-6-EVENT 6-Information [container fingerprint: [chars]] [nvram fingerprint: [chars]] [chars] Normal container fingerprint event in system initialization virt-infra LOG_STD_NO_ACTION FHRP-3-ERROR 3-Error Internal error [chars] An internal software error occurred. fhrp LOG_STD_ACTION FHRP-3-ERROR 3-Error Internal error [chars] An internal software error occurred. fhrp LOG_STD_ACTION FHRP-4-WARN 4-Warning Internal warning [chars] An internal software warning occurred. fhrp LOG_STD_ACTION FHRP-4-WARN 4-Warning Internal warning [chars] An internal software warning occurred. fhrp LOG_STD_ACTION FHRP-6-INFO 6-Information Internal info [chars] An internal software information message occurred. fhrp LOG_STD_ACTION FHRP-6-INFO 6-Information Internal info [chars] An internal software information message occurred. fhrp LOG_STD_ACTION FHS-3-FHS_CLASSIFY_FAIL 3-Error Dataplane FHS classification error for interface [chars] Cisco internal software error. The dataplane was unable to complete processing of FHS Snoop due to a classification failure. This is likely due to a data initialization error cpp-ucode keyword:fhs LOG_STD_ACTION FHS-3-FHS_FILTER_FAIL 3-Error Dataplane FHS filter error for interface [chars] Cisco internal software error. The FHS pktsb shouldn't be set in use before. This is likely due to a data initialization error cpp-ucode keyword:fhs LOG_STD_ACTION FHS-3-FHS_INIT_FAIL 3-Error Dataplane FHS init error for [chars] Cisco internal software error. This is likely due to a dataplane memory exhaust cpp-ucode keyword:fhs LOG_STD_ACTION FHS-3-FHS_MISS_ACTION_FAIL 3-Error Dataplane FHS miss action error for interface [chars] Cisco internal software error. The dataplane was unable to complete processing of FHS Snoop due to a invalid miss action. This is likely due to a data initialization error cpp-ucode keyword:fhs LOG_STD_ACTION FIB-2-DFIBSWITCH 2-Critical Error trying to turn on Distributed CEF without CEF on IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-2-DFIBSWITCH 2-Critical Error trying to turn on Distributed CEF without CEF on IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-2-FIB_OVERLENGTH_XDR 2-Critical Overlength CEF XDR message - len [dec] > [dec] from [chars] An internal software error occurred preventing the sending of an CEF XDR message. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-2-FIB_OVERLENGTH_XDR 2-Critical Overlength CEF XDR message - len [dec] > [dec] from [chars] An internal software error occurred preventing the sending of an CEF XDR message. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-2-FIBDISABLE 2-Critical Fatal error slot [chars]: [chars] An internal software error has occurred because of an IPC problem between the LC and the RP. CEF switching has been disabled on the specified slot. IPV4FIB_DDTS_COMPONENT "Enter the clear cef linecard [slot no] command " "then check the status of the line card by entering the " "show cef linecard command. If the status shows " "that the line card is still disabled disable and re-enable DCEF " "and check the status of the line card again. " LOG_STD_RECUR_ACTION FIB-2-FIBDISABLE 2-Critical Fatal error slot [chars]: [chars] An internal software error has occurred because of an IPC problem between the LC and the RP. CEF switching has been disabled on the specified slot. IPV4FIB_DDTS_COMPONENT "Enter the clear cef linecard [slot no] command " "then check the status of the line card by entering the " "show cef linecard command. If the status shows " "that the line card is still disabled disable and re-enable DCEF " "and check the status of the line card again. " LOG_STD_RECUR_ACTION FIB-2-FIBDOWN 2-Critical CEF has been disabled due to a low memory condition. It can be re-enabled by configuring \ip cef [distributed]\ CEF was disabled because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade the RP so that it has more DRAM." FIB-2-FIBDOWN 2-Critical CEF has been disabled due to a low memory condition. It can be re-enabled by configuring \ip cef [distributed]\ CEF was disabled because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade the RP so that it has more DRAM." FIB-2-FIBFEATSESINIT 2-Critical Error initializing CEF repop feature session queue Initialization of a CEF feature session queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-FIBFEATSESINIT 2-Critical Error initializing CEF repop feature session queue Initialization of a CEF feature session queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-IDBQINIT 2-Critical Error initializing CEF IDB queue Initialization of the CEF IDB queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-IDBQINIT 2-Critical Error initializing CEF IDB queue Initialization of the CEF IDB queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-LINECARDINIT 2-Critical Error initializing CEF Linecard queue Initialization of the CEF linecard queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-LINECARDINIT 2-Critical Error initializing CEF Linecard queue Initialization of the CEF linecard queue could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-XDRINIT 2-Critical Error initializing CEF xdr chunks Initialization of the CEF xdr chunks could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-2-XDRINIT 2-Critical Error initializing CEF xdr chunks Initialization of the CEF xdr chunks could not be accomplished because of a low memory condition. IPV4FIB_DDTS_COMPONENT "Reduce other system activitiy to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FIB-3-FIBBADXDRSLOT 3-Error Invalid XDR slot. Type/len/slot [dec]/[dec]/[chars]. XDR at 0x%08x IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBBADXDRSLOT 3-Error Invalid XDR slot. Type/len/slot [dec]/[dec]/[chars]. XDR at 0x%08x IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBPENDINGLIST 3-Error Error queueing interface [chars] to CEF pending event list. Queueing an interface to the CEF pending up event list failed IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBPENDINGLIST 3-Error Error queueing interface [chars] to CEF pending event list. Queueing an interface to the CEF pending up event list failed IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBSBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified CEF subblock data structure could not be accomplished. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBSBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified CEF subblock data structure could not be accomplished. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBSBNOFN 3-Error Missing [chars] subblock [chars] function for [chars] Functions for distributing this subblock are missing from the image. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBSBNOFN 3-Error Missing [chars] subblock [chars] function for [chars] Functions for distributing this subblock are missing from the image. IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBXDRLEN 3-Error Invalid XDR length. Type [dec][chars]. XDR/buffer len [dec]/[dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-FIBXDRLEN 3-Error Invalid XDR length. Type [dec][chars]. XDR/buffer len [dec]/[dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-INVALIDSTATE 3-Error Slot [chars] in invalid transition from [chars] to [chars] An internal software error ocurred. Linecard is in incorrect state IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-INVALIDSTATE 3-Error Slot [chars] in invalid transition from [chars] to [chars] An internal software error ocurred. Linecard is in incorrect state IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-MAC_ACCT 3-Error [chars]: [chars] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-MAC_ACCT 3-Error [chars]: [chars] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-PREC_ACCT 3-Error [chars]: [chars] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-3-PREC_ACCT 3-Error [chars]: [chars] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBCBLK 4-Warning Missing cef table for tableid [dec] during [chars] event IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBCBLK 4-Warning Missing cef table for tableid [dec] during [chars] event IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBEVENT 4-Warning Invalid event. Type [chars] event [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBEVENT 4-Warning Invalid event. Type [chars] event [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBLCTUNSEQ 4-Warning [chars] Error Initializing/Updating Linecard Tunnel Configuration Configuration of a Tunnel on this linecard may not have been successful because of an internal software error. IPV4FIB_DDTS_COMPONENT "Reconfigure the Tunnel concerned. If problem persists copy the message " "exactly as it appears and report it to your technical support " "representative." FIB-4-FIBLCTUNSEQ 4-Warning [chars] Error Initializing/Updating Linecard Tunnel Configuration Configuration of a Tunnel on this linecard may not have been successful because of an internal software error. IPV4FIB_DDTS_COMPONENT "Reconfigure the Tunnel concerned. If problem persists copy the message " "exactly as it appears and report it to your technical support " "representative." FIB-4-FIBSPECIALPREFIX 4-Warning Invalid Special Prefix Type. Type [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBSPECIALPREFIX 4-Warning Invalid Special Prefix Type. Type [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBXDRINV 4-Warning Invalid format. [chars] [chars] [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-4-FIBXDRINV 4-Warning Invalid format. [chars] [chars] [dec] IPV4FIB_INTERNAL_ERROR IPV4FIB_DDTS_COMPONENT LOG_STD_ACTION FIB-6-FIBLCTUNDELSEQ 6-Information Update received on a linecard for a deleted tunnel[chars] - An update was received on a linecard for a tunnel that has already been deleted and the update was ignored. IPV4FIB_DDTS_COMPONENT LOG_STD_NO_ACTION FIB-6-FIBLCTUNDELSEQ 6-Information Update received on a linecard for a deleted tunnel[chars] - An update was received on a linecard for a tunnel that has already been deleted and the update was ignored. IPV4FIB_DDTS_COMPONENT LOG_STD_NO_ACTION FILESYS_RFS-3-IPC 3-Error [chars] [chars]: msg_type [[dec]] sub_type [[dec]]: IPC error [[chars]] RFS operation failed due to an IPC error. - - FILESYS_RFS-4-RFS_REQUEST_TIMEOUT 4-Warning Timeout has occurred while executing the RFS request on file [chars] [[dec]]. A RFS request is sent to server from the client. While executing the request on the server side timeout has occurred at the client side. - LOG_STD_NO_ACTION FILESYS-3-FLASH 3-Error [chars] [chars] error [dec] A file system error has occurred. - LOG_STD_SH_TECH_ACTION FILESYS-3-IPC 3-Error [chars] [chars]: IPC error [[chars]] RFS operation failed due to an IPC error. - - FILESYS-4-CLPDINT 4-Warning Management interrupts are [chars] for pcmcia device in socket [dec]. [chars] A faulty PCMCIA flash device might be generating spurious insert or remove interrupts continiously. The pcmcia controller will be set temporarily to disable interrupt generation and will be reenabled after a few seconds. This is to avoid storming CPU with spurious interrupts. If the alternate pcmcia device is - "Replace the pcmcia flash device with an alternate one" FILESYS-4-RCSF 4-Warning [chars] [dec] <[chars]> A Running config sync file error has occurred. - LOG_STD_SH_TECH_ACTION FILESYS-5-CFLASH 5-Notice Compact flash card [chars] [chars] A file system's status has changed. Follow any instructions provided with the message. - - FILESYS-5-DEV 5-Notice PCMCIA flash card [chars] [chars] A file system's status has changed. Follow any instructions provided with the message. - LOG_STD_NO_ACTION FILESYS-5-IFLASH 5-Notice Internal Flash [chars] [chars] A file system's status has changed. Follow any instructions provided with the message. - LOG_STD_NO_ACTION FILESYS-5-MISMATCH 5-Notice [chars] device programming algorithm mismatch detected reformat is recommended The flash device programming algorithm written to the device when the flash was formatted is different from what the current running software detected. A reformat of the flash device will solve the problem. - LOG_STD_NO_ACTION FILESYS-5-UNKNDEV 5-Notice Unknown device [chars] [chars] A file system's status has changed. Follow any instructions provided with the message. - LOG_STD_NO_ACTION FLASH-3-CISERR 3-Error Error reading cis of Device [dec] : [dec] bytes read instead of [dec] bytes Error was detected in reading the cis of device. high-flash "Report this error to your technical support representative." FLASH-3-DEVERR 3-Error Error accessing the device : Device number = [dec] Error number = [dec] Error was detected in accessing the device. high-flash "Report this error to your technical support representative." FLASH-4-CLPDINT 4-Warning Management interrupts are [chars] for pcmcia device in socket [dec]. [chars] A faulty PCMCIA flash device might be generating spurious insert or remove interrupts continiously. The pcmcia controller will be set temporarily to disable interrupt generation and will be reenabled after a few seconds. This is to avoid storming CPU with spurious interrupts. If the alternate pcmcia device is - "Replace the pcmcia flash device with an alternate one" FLASH-4-SIMM 4-Warning System Flash Simms unequal. Simm1: [dec]M Simm2: [dec]M The System has detected an unsupported flash configuration. - "Replace Flash Simms with equal sizes or remove Simm from System " "Flash Slot two." FLEX_DNLD-1-INCORRECT_DSP_ID 1-Alert AIM VOICE at slot [dec] receives data from incorrect DSP-ID [dec]. The DSP ID provided by FPGA for download is not valid. - " Call your technical support representative for assistance." FLEX_DNLD-1-INCORRECT_DSP_ID 1-Alert AIM VOICE at slot [dec] receives data from incorrect DSP-ID [dec]. The DSP ID provided by FPGA for download is not valid. - " Call your technical support representative for assistance." FLEX_DNLD-1-NO_RING_DESCRIPTORS 1-Alert No more ring descriptors available on slot [dec] dsp [dec]. The dspfw dnld driver cannot queue messages upto the egress queue for FPGA to transmit. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative. Reset the DSP's on this port \n\ module." FLEX_DNLD-1-NO_RING_DESCRIPTORS 1-Alert No more ring descriptors available on slot [dec] dsp [dec]. The dspfw dnld driver cannot queue messages upto the egress queue for FPGA to transmit. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative. Reset the DSP's on this port \n\ module." FLEX_DNLD-1-NOPCIMEMORY 1-Alert VPM [dec]/[dec] PCI memory unavailable. The router or access server could not allocate memory for the\n\ descriptors. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." FLEX_DNLD-1-NOPCIMEMORY 1-Alert VPM [dec]/[dec] PCI memory unavailable. The router or access server could not allocate memory for the\n\ descriptors. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." FLEX_DNLD-1-TOOBIG 1-Alert [chars] packetsize [dec] too big. A packet greater than the 264 bytes received on this interface. - "The system should recover. No action is required.\n\ \n\ If the problem reccurs it indicates an error that might be\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative." FLEX_DNLD-1-TOOBIG 1-Alert [chars] packetsize [dec] too big. A packet greater than the 264 bytes received on this interface. - "The system should recover. No action is required.\n\ \n\ If the problem reccurs it indicates an error that might be\n\ related to data traffic patterns. Copy the error message exactly as it\n\ appears and report it to your technical support representative." FLEX_DNLD-3-ERROR_ANALYZE 3-Error Error analyzing the device in slot [dec]. The Port module in this slot could not be recognized. - "Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance." FLEX_DNLD-3-ERROR_ANALYZE 3-Error Error analyzing the device in slot [dec]. The Port module in this slot could not be recognized. - "Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance." FLEX_DNLD-3-ERROR_FIRMWARE_DNLD 3-Error DSP firmware download fails for slot [dec] dsp_id [dec] Error initializing the DSP with the application firmware. - " Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance." FLEX_DNLD-3-ERROR_FIRMWARE_DNLD 3-Error DSP firmware download fails for slot [dec] dsp_id [dec] Error initializing the DSP with the application firmware. - " Power down reinsert Port Module and reboot.\n\ If message recurs call your technical support representative for\n\ assistance." FLEX_DNLD-3-NO_FIRMWARE_DNLD 3-Error No DSP firmware download invoked for slot [dec] no DSPs on the card No DSP on the card. - "Plug in DSP on the Network Module" FLEX_DNLD-3-NO_FIRMWARE_DNLD 3-Error No DSP firmware download invoked for slot [dec] no DSPs on the card No DSP on the card. - "Plug in DSP on the Network Module" FLEXDSPRM-3-TDM_CONNECT 3-Error failed to connect voice-port [dec]/[dec]/[dec] to dsp_channel[dec]/[dec]/[dec] TDM connection between Analog/VWIC and the DSP has failed c2800 or c3800 LOG_STD_ACTION FLEXDSPRM-3-TDM_CONNECT 3-Error failed to connect voice-port [dec]/[dec]/[dec] to dsp_channel[dec]/[dec]/[dec] TDM connection between Analog/VWIC and the DSP has failed c2800 or c3800 LOG_STD_ACTION FLEXDSPRM-3-UNSUPPORTED_CODEC 3-Error codec [chars] is not supported on dsp [dec]/[dec] Call failed due to the dsp does not support the codec. PVDM3 "Check dsp capability and make the call on supported dsp" FLEXDSPRM-3-UNSUPPORTED_CODEC 3-Error codec [chars] is not supported on dsp [dec]/[dec] Call failed due to the dsp does not support the codec. PVDM3 "Check dsp capability and make the call on supported dsp" FLEXDSPRM-5-CB_UPDOWN 5-Notice Channel Bank [chars] state is [chars] Channel Bank status has been changed guido "See if the voice ports in the channel bank are UP" FLEXDSPRM-5-CB_UPDOWN 5-Notice Channel Bank [chars] state is [chars] Channel Bank status has been changed guido "See if the voice ports in the channel bank are UP" FLEXDSPRM-5-OUT_OF_RESOURCES 5-Notice [chars] Flex DSPRM temporarily fail to allocate a DSP for this call. A oversubscription has happened and the current free DSP MIPS/Credits are not sufficient to admit a new call. hdv2 or pvdm3 "Check availability of router DSP resource" " and DSP sharing configurations" FLEXDSPRM-5-OUT_OF_RESOURCES 5-Notice [chars] Flex DSPRM temporarily fail to allocate a DSP for this call. A oversubscription has happened and the current free DSP MIPS/Credits are not sufficient to admit a new call. hdv2 or pvdm3 "Check availability of router DSP resource" " and DSP sharing configurations" FLEXDSPRM-5-TDM_SLOT 5-Notice voice channel is being shared from slot [dec]. Configure network-clock-participate slot [dec] Configure network-clock-participate slot for sharing DSPs c2800 or c3800 LOG_STD_ACTION FLEXDSPRM-5-TDM_SLOT 5-Notice voice channel is being shared from slot [dec]. Configure network-clock-participate slot [dec] Configure network-clock-participate slot for sharing DSPs c2800 or c3800 LOG_STD_ACTION FLEXDSPRM-6-DSP_USAGE 6-Information DSP [chars] usage has reached [dec]%% Usage of DSP resources has reached a certain percentage. pvdm3 "Examine whether or not enough " "DSP resources are reserved." FLEXDSPRM-6-DSP_USAGE 6-Information DSP [chars] usage has reached [dec]%% Usage of DSP resources has reached a certain percentage. pvdm3 "Examine whether or not enough " "DSP resources are reserved." FLEXVPN-4-FLEXVPN_FAILED_TO_CONNECT 4-Warning [chars] FlexVPN session failed to come up FlexVPN is stuck in a state waiting for an event posting a disconnect message to recover. - "" FLEXVPN-4-FLEXVPN_FAILED_TO_CONNECT 4-Warning [chars] FlexVPN session failed to come up FlexVPN is stuck in a state waiting for an event posting a disconnect message to recover. - "" FLEXVPN-6-FLEXVPN_CONNECTION_DOWN 6-Information [chars] FlexVPN connection is being closed. The IPsec and IKE security associations will also be brought down along with it. - "" FLEXVPN-6-FLEXVPN_CONNECTION_DOWN 6-Information [chars] FlexVPN connection is being closed. The IPsec and IKE security associations will also be brought down along with it. - "" FLEXVPN-6-FLEXVPN_CONNECTION_UP 6-Information [chars] FlexVPN connection is up for the client mentioned. Both IPsec and IKE security Associations are up now. - "" FLEXVPN-6-FLEXVPN_CONNECTION_UP 6-Information [chars] FlexVPN connection is up for the client mentioned. Both IPsec and IKE security Associations are up now. - "" FLOWMON-1-ALERT_CRI_CLEAR 1-Alert [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-1-ALERT_CRI_SET 1-Alert [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-2-ALERT_ERROR_CLEAR 2-Critical [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-2-ALERT_ERROR_SET 2-Critical [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-2-FLOW_ALERT 2-Critical Performance_Traffic_ALERT[[chars]]: [[chars]] Generated when the Flow monitoring alert are detected flomon "NA" FLOWMON-2-FLOW_THRESHOLD_EXCEEDED 2-Critical Performance_Traffic_TCA[[chars]]: Exceeded configured [dec] current [dec] Generated when the Flow monitoring threshold has crossed the configured limit flomon "NA" FLOWMON-2-FLOW_THRESHOLD_RANGE_EXCEEDED 2-Critical Performance_Traffic_TCA[[chars]]: Exceeded configured range[dec] [dec] current [dec] Generated when the Flow monitoring threshold has crossed into the configured range limit flomon "NA" FLOWMON-3-ALERT_NOTIFY_CLEAR 3-Error [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-3-ALERT_NOTIFY_SET 3-Error [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-4-ALERT_ALERT_CLEAR 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-4-ALERT_ALERT_SET 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-4-ALERT_EMERGENCY_CLEAR 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-4-ALERT_EMERGENCY_SET 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-4-ALERT_INFM_CLEAR 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-4-ALERT_INFM_SET 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FLOWMON-4-ALERT_SCALE_LIMIT 4-Warning Flow scale limit reached on LC. New Flows can get learnt when existing flows timeout Generated when the Flow scale limit is reached on LC and new flow tries to learn flomon "NA" FLOWMON-4-ALERT_WAR_CLEAR 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has gone below the configured limit and the condition is being cleared flomon "NA" FLOWMON-4-ALERT_WAR_SET 4-Warning [[chars]]: SRC_IP:[inet] SRC_PORT:%lu DST_IP:[inet] DST_PORT:%lu [chars][chars] [chars] [chars] Generated when the Flow monitoring threshold has crossed the configured limit and the condition is being set flomon "NA" FM-1-INIT 1-Alert Feature Manager subsystem initialization failure The Feature Manager subsystem failed to initialize. Most likely cause is insufficient memory at init time. Probably either the hardware has failed or this image is being run on a platform it was not intended for. firmware "Replace failing hardware or obtain the correct " "IOS image for this platform whichever is " "appropriate." FM-2-NOMAP 2-Critical Cannot create Feature Manager data structures for VLAN Map [chars] The Feature Manager could not allocate the data structures needed to describe a VLAN Map in a form that can be loaded into hardware. Probably caused by lack of free memory. firmware LOG_STD_REDUCE_ACTION FM-2-NOSB 2-Critical Cannot create subblock for interface [chars] The Feature Manager was unable to save per-interface information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly. firmware "Use a less complicated configuration that " "requires less memory." FM-2-NOVLB 2-Critical Cannot create memory block for VLAN [dec] The Feature Manager was unable to save per-VLAN information needed for its correct operation. Some per-interface features such as access groups or VLAN maps will not be configured correctly. firmware "Use a less complicated configuration that " "requires less memory." FM-2-NOVMR 2-Critical Cannot create VMR data structures for access list [chars] The Feature Manager could not allocate the data structures needed to describe an ACL in a form that can be loaded into hardware. Probably caused by lack of available memory. firmware "Use a less complicated configuration that " "requires less memory." FM-3-AUGMENTFAIL 3-Error Augmenting of access-map [chars] on [chars] label [dec] failed The system ran out of CPU memory when attempting to merge internally required elements with the configured access maps. firmware LOG_STD_REDUCE_ACTION FM-3-CONFLICT 3-Error [chars] [chars] conflicts with [chars] Port access lists PACLs may not be applied when input router access lists or VLAN maps have been applied and vice versa firmware "Remove the conflicting feature or features" FM-3-GOTLABEL 3-Error Got label for [chars] The Feature Manager has now been able to allocate a hardware label for the interface. The interface had needed a label before but none was available. - LOG_STD_NO_ACTION FM-3-GOTVLABEL 3-Error Got label for VLAN #[dec] The Feature Manager has now been able to allocate a hardware label for the VLAN. The VLAN had needed a label before but none was available. - LOG_STD_NO_ACTION FM-3-ILLEGALCOPY 3-Error Illegal copy of [chars] access group [chars] from [chars] label [dec] to [dec] An internal software error has occurred firmware "show running-config" FM-3-INITLABEL 3-Error Special initialization of label [dec] failed Initialization of the access list hardware failed. Prioritization of routing protocol packets above other kinds of packets may not occur on some VLANs or routed ports. firmware LOG_STD_ACTION FM-3-INSERTFAIL 3-Error Insert of access-map [chars] #[dec] into [chars] label [dec] failed The system ran out of CPU memory when trying to merge sections of an access map. firmware "Reduce other system activity to ease the memory demands. For example " "remove any ACLs that have been defined but are not now used. Use " "simpler ACLs with fewer access control entries ACEs. Use fewer " FM-3-INTTABLE 3-Error Not in truth table: VLMAP [dec] RACL [dec] Rtprot [dec] Redir [dec] Mcb [dec] Feat [dec] An unrecoverable software error occurred while trying to merge the configured input features. firmware "show running-config" FM-3-LABELERROR 3-Error Incorrect label to [chars] vlan label attribute copy callback srclabel [dec] dstlabel [dec] The Feature Manager attribute copy callback was called with an incorrect source or destination label. firmware "show running-config" FM-3-MAXRECURSION 3-Error Too many [dec] levels of recursion while merging [chars] code [dec]. The configuration is too complicated for the platform specific ACL merge code to support. Most likely cause is including too many separate access lists in a single VLAN map or policy map. - "Reduce the number IP or MAC access lists" " considered separately in any one VLAN or policy" FM-3-MERGEFAIL 3-Error [chars] ACL merge error [dec] [chars] on [chars] label [dec] The Feature Manager was unable to complete the merge of the configured features into a form suitable for loading into the hardware. Packets potentially affected by this feature will be sent to the CPU for processing instead. The most likely cause is specifying an ACL that is too large or too complex for the system to handle. firmware "Try specifying a smaller and less complicated " "configuration." FM-3-NOLABEL 3-Error Cannot allocate [chars] label for interface [chars] The Feature Manager was unable to allocate a label for the features on this interface. This means that the hardware cannot be programmed to implement the features and packets for this interface will be filtered in software. There is a limit of 256 labels per direction. firmware "Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible." FM-3-NOLABELVL 3-Error Cannot allocate [chars] label for VLAN [dec] The Feature Manager was unable to allocate a label for the features on this VLAN. This means that the hardware cannot be programmed to implement the features and packets on this VLAN will be filtered in softtware. There is a limit of 256 labels per direction. firmware "Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same VLAN Maps on multiple " "VLANs if possible." FM-3-NOTEMPTY 3-Error Illegal copy of attribute to non empty [chars] vlan label [dec] The Feature Manager attribute copy callback was called with a destination label already being used by a VLAN or routed port. firmware "show running-config" FM-3-NOTOBJECT 3-Error Invalid object VLAN [dec] IDB [hec] used in Feature Manager operation An internal software error has occurred firmware "show running-config" FM-3-OUTTTABLE 3-Error Not in truth table: RACL [dec] VLMAP [dec] An unrecoverable software error occurred while trying to merge the configured output features. firmware "show running-config" FM-3-QOSTTABLE 3-Error Not in truth table: ACL [dec] in map action [dec] A software error occurred while trying to merge a QoS Policy Map firmware "show running-config" FM-3-RELOADED 3-Error Reloading [chars] label [dec] feature in [chars] The Feature Manager was able to fit more of the configured features on this label into the hardware. One or more features had previously been unloaded because of lack of space. - LOG_STD_NO_ACTION FM-3-TOSCOST 3-Error Minimize monetary cost TOS bit unsupported in hardware ignored This hardware platform supports filtering based on DSCP rather than TOS and precedence. The DSCP field does not include the minimize monetary cost bit from the TOS field so hardware will ignore this bit when checking for a match to an ACE. This can lead to unintended filtering actions. firmware "Design filters that do not test for minimum " "monetary cost TOS." FM-3-UNKNOWNACTION 3-Error Unknown VMR access group action 0x[hec] An internal software error has occurred. firmware LOG_STD_ACTION FM-3-UNLOADING 3-Error Unloading [chars] label [dec] feature from [chars] The Feature Manager was unable to fit the complete configuration into the hardware so some features will have to be applied in software. This prevents some or all of the packets from being forwarded in hardware and requires them to be forwarded by the CPU. Multicast packets may be dropped entirely instead of being forwarded. firmware "Allocate more space to the relevant section " "of the TCAM and reboot or else use a simpler " "configuration. Use the same ACLs on multiple " "interfaces if possible." FM-3-WRONGLABEL 3-Error Inconsistent records of label for [chars]: FM has [dec] LM has [dec] An internal software error has occurred. firmware "show running-config" FM-4-EXCESSSECONDARY 4-Warning More than [dec] secondary IP addresses configured on interface [chars] When secondary IP addresses are configured on an interface the hardware is usually programmed so that the ICMP redirect functionality on the CPU is not notified of packets sent between two subnets configured on the same interface. If many secondary IP addresses are configured on the same interface it becomes impractical to program the hardware in this manner this message is logged and the CPU will be notified of every packet sent between two subnets on this interface. No ICMP redirects will be sent in error but the CPU usage may increase because of the additional notifications. The user may wish to configure \no ip redirects\ on the interface to reduce the CPU load on the system. firmware "configure the \"no ip redirects\" command on " "this interface" FM-7-TRANSDEF 7-Debug No augmentation function found for VMR An Internal Error occured. An Access Control List was not interpretted correctly. The Value-Mask Result is incorrect. firmware LOG_STD_ACTION FMANRP_ACL-3-EXPOGACLLIMITERR 3-Error Expanded OGACL [chars] size [dec] exceeded MAX ACL limit [dec] Expanded OGACL size exceeded the maximum ACL limit. Command rejected iosxe-acl "Reduce # of ACEs in the ACL" FMANRP_ACL-4-INVALIDV4ACETYPE 4-Warning v4 ACE type is invalid An unexpected condition has occurred which is due to the type of v4 ACE\n\ created iosxe-acl "show ip access-list" FMANRP_ACL-4-INVALIDV6OP 4-Warning Operation is invalid An unexpected condition has occurred which is due to the operation \n\ performed iosxe-acl "show ipv6 access-list" FMANRP_ACL-4-NOACL 4-Warning ACL is null An unexpected condition has occurred which is due to the absence of\n\ an ACL structure. iosxe-acl "show ip access-list" FMANRP_ACL-4-NOMACACE 4-Warning mac ACE is null An unexpected condition has occurred which is due to the absence of\n\ an mac ACE structure. iosxe-acl "show access-list" FMANRP_ACL-4-NOSB 4-Warning Subblock on interface [chars] 0x[hec] is null An unexpected condition has occurred which is due to the absence of\n\ a subblock structure on interface. iosxe-acl "show ip interface" FMANRP_ACL-4-NOSWIDB 4-Warning Sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a swidb structure. iosxe-acl "show ip interface" FMANRP_ACL-4-NOV4ACE 4-Warning v4 ACE is null An unexpected condition has occurred which is due to the absence of\n\ an v4 ACE structure. iosxe-acl "show ip access-list" FMANRP_ACL-4-NOV6ACE 4-Warning v6 ACE is null An unexpected condition has occurred which is due to the absence of\n\ an v6 ACE structure. iosxe-acl "show ipv6 access-list" FMANRP_ACL-4-TMPLACLDISABLEERR 4-Warning Not enough resources to disable template ACL Not enough resurces to store individual ACLs iosxe-acl "show ip access-list template summary" FMANRP_ACL-4-TMPLACLINITERR 4-Warning Template ACL initialization error An unexpected condition has occurred on template ACL initialization iosxe-acl "show memory" FMANRP_ACL-4-TMPLACLNOMEMERR 4-Warning Template ACL no memory error An unexpected condition has occurred on template ACL processing iosxe-acl "show memory" FMANRP_ACL-4-UPDMACSTATSERR 4-Warning Update mac ACL statistics error An unexpected condition has occurred when updating mac ACL statistics iosxe-acl "show access-list" FMANRP_ACL-4-UPDV4STATSERR 4-Warning Update v4 ACL statistics error An unexpected condition has occurred when updating v4 ACL statistics iosxe-acl "show ip access-list" FMANRP_ACL-4-UPDV6STATSERR 4-Warning Update v6 ACL statistics error An unexpected condition has occurred when updating v6 ACL statistics iosxe-acl "show ipv6 access-list" FMANRP_ALG-3-API_FAILED 3-Error NULL A call to the API of another component has indicated an\n\ error. iosxe-alg LOG_STD_ACTION FMANRP_ALG-3-EINVAL 3-Error NULL An unexpected input value to a function was incorrect iosxe-alg LOG_STD_ACTION FMANRP_DPSS-3-DPSSFOIOSDENQUEUE 3-Error Failed to enqueue dpss feature object 0x[hec] config message for transmission This operation to enqueue an IPC message for sending has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSFOIPCALLOC 3-Error Failed to alloc IPC buffer for dpss feature object 0x[hec] config\n\ message This operation to allocate IPC buffer for dpss feature object \n\ configuration has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSFOTDLCREATE 3-Error Failed to create tdl msg for dpss feature object 0x[hec] config message This operation to create an TDL message has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSFOTDLMSGMARSHAL 3-Error Failed to copy dpss feature object config message to IPC buffer for\n\ fo_hdl 0x[hec] This operation to build a TDL message for dpss feature object \n\ configuration has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSFOTDLSET 3-Error Failed to set tdl msg detail for dpss feature object 0x[hec] config message This operation to set an TDL message has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSGLOBALIOSDENQUEUE 3-Error Failed to enqueue dpss global config message for transmission This operation to enqueue an IPC message for sending has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSGLOBALIPCALLOC 3-Error Failed to alloc IPC buffer for dpss global config\n\ message This operation to allocate IPC buffer for dpss global \n\ configuration has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSGLOBALTDLCREATE 3-Error Failed to create tdl msg for dpss global config message This operation to create an TDL message has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSGLOBALTDLMSGMARSHAL 3-Error Failed to copy dpss global config message to IPC buffer This operation to build a TDL message for dpss global \n\ configuration has failed. asr1k-dpss LOG_STD_ACTION FMANRP_DPSS-3-DPSSGLOBALTDLSET 3-Error Failed to set tdl msg detail for dpss global config message This operation to set an TDL message has failed. asr1k-dpss LOG_STD_ACTION FMANRP_ESS-3-ENQUEFAIL 3-Error [chars] [hex] [hex] - - - FMANRP_ESS-3-ERREVENT 3-Error [chars] [hex] - - - FMANRP_ESS-3-ERREVENT2 3-Error [chars] [hex] / [hex] - - - FMANRP_ESS-4-EVSICREAT 4-Warning [chars] sip_ess_segment= [hex] segment_id= [dec] fsp_ess_segment= [hex] segment_id= [dec] evsi= [dec] A failure has occured in creating a session interface. iosxe-bb " The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION FMANRP_ESS-4-FULLVAI 4-Warning Session creation failed due to Full Virtual-Access Interfaces not being supported. Check that all applied Virtual-Template and RADIUS features support Virtual-Access sub-interfaces. swidb= [hex] ifnum= [dec] A failure has occured in creating a session interface due to a Full Virtual-Access Interface being created. Full Virtual-Access Interface are created if a Virtual-Template or RADIUS feature does not support Virtual-Access sub-interfaces. This platform only supports Virtual-Access sub-interfaces. Refer to Action to isolate offending feature. iosxe-bb " The session creation is rejected." " Steps to isolate unsupported Session feature:\n" " Run 'test Virtual-Template # subinterface' where" " # is the Virtual-Template number being used to" " create the session. Remove any identified" " features that are not sub-interface compliant.\n" " For RADIUS features:\n" " Configure \"aaa policy interface-config" " allow-subinterface\" on the router or\n" " cisco-avpair=\"lcp:allow-subinterface=yes\" needs" " to be specified in the subscriber profile on the" " Radius server." FMANRP_ESS-4-MAXSESS 4-Warning [chars] [dec] - - - FMANRP_ESS-4-SEGFAIL 4-Warning [chars] Seghandle 0x[hec] of Type [dec] A failure has occured with a segment operation. iosxe-bb " The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION FMANRP_ESS-4-SEGFAIL2 4-Warning [chars] Seghandle 0x[hec] of Type [dec] ess_segment= [hex] A failure has occured with a segment operation. iosxe-bb " The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION FMANRP_ESS-4-SESSCNT 4-Warning [chars] [hex] - - - FMANRP_ESS-4-WRNEVENT 4-Warning [chars] [hex] - - - FMANRP_ESS-4-WRNEVENT2 4-Warning [chars] [hex] / [hex] - - - FMANRP_ESS-4-WRNPARAM 4-Warning [chars] A failure has occured relating to an incorrect functional parameters. iosxe-bb " The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION FMANRP_ESS-4-WRNPARAM_2U 4-Warning [chars] [dec] / [dec] - - - FMANRP_ESS-4-WRNPARAM_2X 4-Warning [chars] [hex] / [hex] - - - FMANRP_ESS-4-WRNPARAM_2X2S 4-Warning [chars] [hex] / [hex] / [chars] / [chars] - - - FMANRP_ESS-4-WRNPARAM_2XD 4-Warning [chars] [hex] / [hex] / [dec] - - - FMANRP_ESS-4-WRNPARAM_3X 4-Warning [chars] [hex] / [hex] / [hex] - - - FMANRP_ESS-4-WRNPARAM_D 4-Warning [chars] [dec] - - - FMANRP_ESS-4-WRNPARAM_DU 4-Warning [chars] [dec] / [dec] - - - FMANRP_ESS-4-WRNPARAM_F2S 4-Warning [chars]: [chars] [chars] / [chars] - - - FMANRP_ESS-4-WRNPARAM_F2X 4-Warning [chars]: [chars] [hex] / [hex] - - - FMANRP_ESS-4-WRNPARAM_FU 4-Warning [chars]: [chars] [dec] - - - FMANRP_ESS-4-WRNPARAM_S 4-Warning [chars]: [chars] A failure has occured relating to an incorrect functional parameters. iosxe-bb " The session creation is rejected." " If you determine that the system is" " adversely affected then" LOG_STD_ACTION FMANRP_ESS-4-WRNPARAM_U 4-Warning [chars] [dec] - - - FMANRP_ESS-4-WRNPARAM_U2X 4-Warning [chars] [dec] / [hex] / [hex] - - - FMANRP_ESS-4-WRNPARAM_UXD 4-Warning [chars] [dec] / [hex] / [dec] - - - FMANRP_ESS-4-WRNPARAM_XU 4-Warning [chars] [hex] / [dec] - - - FMANRP_EVPN-3-UNSPOP 3-Error Unsupport operation An unexpected operation is get during EVPN configuration iosxe-evpn LOG_STD_ACTION FMANRP_IPSEC-3-HAPI_PCP_UNEXP_REPLY 3-Error [chars]: PCP trans 0x[hec] opcode 0x[hec]: unexpected reply from crypto An unexpected internal software error. Engineering must be reported and investigate this occurrence. iosxe-ipsec LOG_STD_DDTS_TAC_DETAILS FMANRP_IPSEC-6-HAPI_PCP_NACK 6-Information [chars]: PCP NACK trans 0x[hec] opcode 0x[hec] errcode 0x[hec]: crypto A failure has occured during security policy downloading in crypto hardware. The command is rejected. iosxe-ipsec "The configuration may be ignorable or recovered " "automatically in crypto hardware. The session may " "still be functional but less than optimal " "performance. If you determine that the system is " "adversely affected then Embedded Services Processor " "ESP tracelog should be collected. " FMANRP_MFR-3-BLCFGFAIL 3-Error Unable to [chars] link [chars] [chars] An unexpected condition has occurred at Bundle link configuration [chars] iosxe-mlfr LOG_STD_ACTION FMANRP_MFR-3-BLFAIL 3-Error Unable to [chars] link [chars] [chars] An unexpected condition has occurred at Bundle link configuration [chars] iosxe-mlfr LOG_STD_ACTION FMANRP_MFR-3-BNDLFAIL 3-Error Unable to [chars] bundle [chars] An unexpected condition has occurred at Bundle configuration iosxe-mlfr LOG_STD_ACTION FMANRP_MFR-3-TDLFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process [chars] An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. iosxe-mlfr LOG_STD_ACTION FMANRP_MPLS-3-ENQUEFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. asr1k-fwdmgr LOG_STD_ACTION FMANRP_MPLS-3-NOOBJ 3-Error Object entry is null An unexpected condition has occurred which is due to the absence of\n\ an object entry structure. asr1k-fwdmgr "show mpls" FMANRP_MPLS-3-UNSPTYPE 3-Error Not supported bundle type [dec] An unexpected condition has occurred which is due to an operation request\n\ to an unsupported bundle oce type is received. asr1k-fwdmgr LOG_STD_ACTION FMANRP_NAT-3-AVLDELETE 3-Error Failed to delete node from NAT [chars] database for [inet] This operation to perform delete processing has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-AVLDELETE 3-Error Failed to delete node from NAT [chars] database for [inet] This operation to perform delete processing has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-AVLTREEWALK 3-Error Failed to walk NAT [chars] database for [chars] This operation to perform stale processing has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-AVLTREEWALK 3-Error Failed to walk NAT [chars] database for [chars] This operation to perform stale processing has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-DEBUGTDLMSGMARSHAL 3-Error Failed to copy debug NAT request message to IPC buffer This operation to build a TDL message for debug NAT command \n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-DEBUGTDLMSGMARSHAL 3-Error Failed to copy debug NAT request message to IPC buffer This operation to build a TDL message for debug NAT command \n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IFADDRTDLMSGMARSHAL 3-Error Failed to copy interface address change message to IPC buffer for\n\ interface [chars] new address [inet] This operation to build a TDL message for NAT interface address\n\ configuration has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IFADDRTDLMSGMARSHAL 3-Error Failed to copy interface address change message to IPC buffer for\n\ interface [chars] new address [inet] This operation to build a TDL message for NAT interface address\n\ configuration has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IFTDLMSGMARSHAL 3-Error Failed to copy interface config essage to IPC buffer for \n\ Interface [chars] 0x[hec] domain [chars] operation [chars] This operation to build a TDL message for interface configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IFTDLMSGMARSHAL 3-Error Failed to copy interface config essage to IPC buffer for \n\ Interface [chars] 0x[hec] domain [chars] operation [chars] This operation to build a TDL message for interface configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-INVALID_ADDRESS 3-Error Received an invalid address [inet] An unsupported address for the given config was received. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-INVALID_ADDRESS 3-Error Received an invalid address [inet] An unsupported address for the given config was received. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IOSDENQUEUE 3-Error Failed to enqueue NAT [chars] message for transmission This operation to enqueue an IPC message for sending has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IOSDENQUEUE 3-Error Failed to enqueue NAT [chars] message for transmission This operation to enqueue an IPC message for sending has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPALIASTDL 3-Error Error with ipalias message received from data path An unexpected condition has occurred with received ipalias \n\ message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPALIASTDL 3-Error Error with ipalias message received from data path An unexpected condition has occurred with received ipalias \n\ message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPALIASTYPE 3-Error Received ipalias message from data path with unsupported \n\ address type [dec] An unexpected condition has occurred with received ipalias \n\ message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPALIASTYPE 3-Error Received ipalias message from data path with unsupported \n\ address type [dec] An unexpected condition has occurred with received ipalias \n\ message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPSTATICROUTETDL 3-Error Error with static ip route message received from data path An unexpected condition has occurred with received static\n\ ip route message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPSTATICROUTETDL 3-Error Error with static ip route message received from data path An unexpected condition has occurred with received static\n\ ip route message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPSTATICROUTETYPE 3-Error Received ip static route message from data path with\n\ unsupported address type An unexpected condition has occurred with received static \n\ ip route message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-IPSTATICROUTETYPE 3-Error Received ip static route message from data path with\n\ unsupported address type An unexpected condition has occurred with received static \n\ ip route message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MAPPINGTDLMSGMARSHAL 3-Error Failed to copy mapping config message to IPC buffer for\n\ mapping id [dec] vrf table id [dec] This operation to build a TDL message for mapping configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MAPPINGTDLMSGMARSHAL 3-Error Failed to copy mapping config message to IPC buffer for\n\ mapping id [dec] vrf table id [dec] This operation to build a TDL message for mapping configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MAXENTRYTDLMSGMARSHAL 3-Error Failed to copy max entry config message to IPC buffer for\n\ type [chars] entry data 0x[hec] max_limit [dec] This operation to build a TDL message for max entry add/delete\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MAXENTRYTDLMSGMARSHAL 3-Error Failed to copy max entry config message to IPC buffer for\n\ type [chars] entry data 0x[hec] max_limit [dec] This operation to build a TDL message for max entry add/delete\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MIBEVENT 3-Error Failed to get NAT MIB response message: [chars] An unsupported error occured with waiting for NAT MIB respsonse \n\ message. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MIBEVENT 3-Error Failed to get NAT MIB response message: [chars] An unsupported error occured with waiting for NAT MIB respsonse \n\ message. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MSGALLOCERR 3-Error Failed to allocate message When attempting to send message to dataplane there was not enough memory to allocate the message. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-MSGALLOCERR 3-Error Failed to allocate message When attempting to send message to dataplane there was not enough memory to allocate the message. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-NATSETTDLMSGFAIL 3-Error When download [chars] failed to set a field in message sotware error. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-NATSETTDLMSGFAIL 3-Error When download [chars] failed to set a field in message sotware error. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-POOLTDLMSGMARSHAL 3-Error Failed to copy pool config message to IPC buffer for\n\ pool [chars] id [dec] This operation to build a TDL message for pool configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-POOLTDLMSGMARSHAL 3-Error Failed to copy pool config message to IPC buffer for\n\ pool [chars] id [dec] This operation to build a TDL message for pool configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTPROTO 3-Error Protocol type [dec] for global addr [inet] in the portlist allocation request is not supported An unexpected protocol type has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTPROTO 3-Error Protocol type [dec] for global addr [inet] in the portlist allocation request is not supported An unexpected protocol type has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTDL 3-Error Error with portlist allocation request message received from data path An unexpected condition has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTDL 3-Error Error with portlist allocation request message received from data path An unexpected condition has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTDLMSGMARSHAL 3-Error Failed to copy portlist config message to IPC buffer for\n\ addr [inet] proto [dec] start_port [dec] end_port [dec] This operation to build a TDL message for portlist add/delete\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTDLMSGMARSHAL 3-Error Failed to copy portlist config message to IPC buffer for\n\ addr [inet] proto [dec] start_port [dec] end_port [dec] This operation to build a TDL message for portlist add/delete\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTYPE 3-Error Address type [dec] for global address in the portlist allocation request is not supported An unexpected address type has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-PORTLISTTYPE 3-Error Address type [dec] for global address in the portlist allocation request is not supported An unexpected address type has occurred with received portlist\n\ allocation request message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-RANGETDLMSGMARSHAL 3-Error Failed to copy pool address range config message to IPC buffer for\n\ pool [chars] range start [inet] range end [inet] This operation to build a TDL message for address range configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-RANGETDLMSGMARSHAL 3-Error Failed to copy pool address range config message to IPC buffer for\n\ pool [chars] range start [inet] range end [inet] This operation to build a TDL message for address range configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-SERTDLMSGMARSHAL 3-Error Failed to copy service config message to IPC buffer for\n\ application type [dec] protocol type [dec] port [dec] This operation to build a TDL message for service configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-SERTDLMSGMARSHAL 3-Error Failed to copy service config message to IPC buffer for\n\ application type [dec] protocol type [dec] port [dec] This operation to build a TDL message for service configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-SERVICERM 3-Error Failed to delete NAT services for appl type [chars] protocol [chars]\n\ port [dec] An unexpected condition has occurred which is due to the failure\n\ to remove data structures for NAT special services. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-SERVICERM 3-Error Failed to delete NAT services for appl type [chars] protocol [chars]\n\ port [dec] An unexpected condition has occurred which is due to the failure\n\ to remove data structures for NAT special services. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-STATSUPDTDL 3-Error Failed to update NAT [chars] statistics An unexpected condition has occurred when updating statistics iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-STATSUPDTDL 3-Error Failed to update NAT [chars] statistics An unexpected condition has occurred when updating statistics iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-TIMEOUTTDLMSGMARSHAL 3-Error Failed to copy timeout config message to IPC buffer for\n\ timeout type [dec] This operation to build a TDL message for timeout configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-TIMEOUTTDLMSGMARSHAL 3-Error Failed to copy timeout config message to IPC buffer for\n\ timeout type [dec] This operation to build a TDL message for timeout configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-VRFDELTDLMSGMARSHAL 3-Error Failed to copy VRF delete message to IPC buffer for vrf table id [dec] This operation to build a TDL message for vrf deletion configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-VRFDELTDLMSGMARSHAL 3-Error Failed to copy VRF delete message to IPC buffer for vrf table id [dec] This operation to build a TDL message for vrf deletion configuration\n\ has failed. iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSIDB 3-Error Received WLAN session message from data path with nil \n\ input interface for inside local host [inet] An unexpected condition has occurred with received WLAN session \n\ message from data path with nil input interface iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSIDB 3-Error Received WLAN session message from data path with nil \n\ input interface for inside local host [inet] An unexpected condition has occurred with received WLAN session \n\ message from data path with nil input interface iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSTDL 3-Error Error with WLAN session message received from data path An unexpected condition has occurred with received WLAN session \n\ message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSTDL 3-Error Error with WLAN session message received from data path An unexpected condition has occurred with received WLAN session \n\ message from data path iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSTYPE 3-Error Received WLAN session message from data path with unsupported \n\ address type [dec] An unexpected condition has occurred with received WLAN session \n\ message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-3-WLANSESSTYPE 3-Error Received WLAN session message from data path with unsupported \n\ address type [dec] An unexpected condition has occurred with received WLAN session \n\ message from data path with unsupported address type iosxe-nat LOG_STD_ACTION FMANRP_NAT-4-BADACTION 4-Warning Invalid action [dec] for NAT configuration An unexpected condition has occurred which is invalid action \n\ for a NAT configuration. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-BADACTION 4-Warning Invalid action [dec] for NAT configuration An unexpected condition has occurred which is invalid action \n\ for a NAT configuration. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-LOGGING_PARAM 4-Warning Highspeed logging export [chars] [dec] unsupported An unsupported exporting paremeter for highspeed logging\n\ on data path is received. iosxe-nat "show running" FMANRP_NAT-4-LOGGING_PARAM 4-Warning Highspeed logging export [chars] [dec] unsupported An unsupported exporting paremeter for highspeed logging\n\ on data path is received. iosxe-nat "show running" FMANRP_NAT-4-NOACL 4-Warning Access list is null An unexpected condition has occurred which is due to the absence of\n\ an access list structure. iosxe-nat "show ip access-lists" FMANRP_NAT-4-NOACL 4-Warning Access list is null An unexpected condition has occurred which is due to the absence of\n\ an access list structure. iosxe-nat "show ip access-lists" FMANRP_NAT-4-NOLOGGINGPARAM 4-Warning Highspeed logging structure is nil An unexpected condition has occurred which is due to the absence of\n\ a logging parameter structure. iosxe-nat "show running" FMANRP_NAT-4-NOLOGGINGPARAM 4-Warning Highspeed logging structure is nil An unexpected condition has occurred which is due to the absence of\n\ a logging parameter structure. iosxe-nat "show running" FMANRP_NAT-4-NOMAPPING 4-Warning A mapping structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT mapping structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NOMAPPING 4-Warning A mapping structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT mapping structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NONATSERVICE 4-Warning Service structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT service structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NONATSERVICE 4-Warning Service structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT service structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NOPOOL 4-Warning Pool structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT pool structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NOPOOL 4-Warning Pool structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT pool structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NORANGE 4-Warning Pool address range structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT pool address range structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NORANGE 4-Warning Pool address range structure is null An unexpected condition has occurred which is due to the absence of\n\ a NAT pool address range structure. iosxe-nat LOG_STD_SH_CMD_ACTION FMANRP_NAT-4-NOREPLICATEPARAM 4-Warning Session replication structure is nil An unexpected condition has occurred which is due to the absence of\n\ a session replication parameter structure. iosxe-nat "show running" FMANRP_NAT-4-NOREPLICATEPARAM 4-Warning Session replication structure is nil An unexpected condition has occurred which is due to the absence of\n\ a session replication parameter structure. iosxe-nat "show running" FMANRP_NAT-4-NOSWIDB 4-Warning Sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a swidb structure. iosxe-nat "show ip interface" FMANRP_NAT-4-NOSWIDB 4-Warning Sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a swidb structure. iosxe-nat "show ip interface" FMANRP_NAT64-3-API_FAILED 3-Error NULL A call to the API of another component has indicated an\n\ error. iosxe-nat LOG_STD_ACTION FMANRP_NAT64-3-EINVAL 3-Error NULL An unexpected input value to a function was incorrect iosxe-nat LOG_STD_ACTION FMANRP_NAT66-3-API_FAILED 3-Error NULL A call to the API of another component has indicated an\n\ error. iosxe-nat LOG_STD_ACTION FMANRP_NAT66-3-EINVAL 3-Error NULL An unexpected input value to a function was incorrect iosxe-nat LOG_STD_ACTION FMANRP_NETFLOW-3-AGGRCACHENULL 3-Error The pointer for aggregation cache type [dec] is NULL An unexpected condition has occurred which is due to the absence of\n\ an aggregation cache data structure. iosxe-netflow "show ip cache flow" FMANRP_NETFLOW-3-CACHETDLMSGMARSHAL 3-Error Failed to copy cache config message to IPC buffer for cache type [dec] The operation of building a TDL message for cache configuration\n\ has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-CLRSTATSTDLMSGMARSHAL 3-Error Failed to copy clear statistics message to IPC buffer The operation of building a TDL message for clearing statistics \n\ in the data path has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-EXPORTERSRCIFINVALID 3-Error Management interface [chars] cannot be used as source for an exporter Exporter configuration failed because the management interface cannot be configured as source interface iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-EXPORTERTDLMSGMARSHAL 3-Error Failed to copy exporter config message to IPC buffer for cache \n\ type [dec] The operation of building a TDL message for exporter configuration\n\ has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-EXPORTERVRFINVALID 3-Error Management vrf [chars] cannot be used as exporter destination Exporter configuration failed because management vrf cannot be used as exporter destination iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-IFFLOWTDLMSGMARSHAL 3-Error Failed to copy interface flow config message to IPC buffer for [chars] The operation of building a TDL message for interface flow configuration\n\ has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-INVALIDFLOWDEFCPP 3-Error CPP Flow definition can not be created [dec] The operation of building a flow definition using flow fields received from CPP has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-NOSAMPLER 3-Error Sampler for sampler-map name [chars] is null An unexpected condition has occurred which is due to the absence of\n\ a sampler-map structure iosxe-netflow "show sampler" FMANRP_NETFLOW-3-NOSAMPLERNAME 3-Error Sampler-map name is null An unexpected condition has occurred which is due to the absence of\n\ a sampler-map name. iosxe-netflow "show sampler" FMANRP_NETFLOW-3-SAMPLERTDLMSGMARSHAL 3-Error Failed to copy sampler-map config message to IPC buffer for [chars] The operation of building a TDL message for sampler-map configuration\n\ has failed. iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-STATSUPDTDL 3-Error Failed to update netflow [chars] statistics An unexpected condition has occurred when updating statistics iosxe-netflow LOG_STD_ACTION FMANRP_NETFLOW-3-UNKNOWNCACHECMD 3-Error Unknown aggregation cache command [dec] received The aggregation cache configuration command has failed due to \n\ unknown command. - LOG_STD_ACTION FMANRP_NETFLOW-3-UNKNOWNCACHETYPE 3-Error Unknown cache type [dec] received The cache configuration command has failed due to unknown\n\ cache scheme type. - LOG_STD_ACTION FMANRP_NETFLOW-4-EXPORTERVERSION 4-Warning Failed to change default exporter version to [dec] The operation of changing the default exporter version has failed. iosxe-netflow "show ip flow export" FMANRP_NETFLOW-4-NOFIBIDB 4-Warning fibdb for interface [chars] is null An unexpected condition has occurred which is due to the absence\n\ of a fibidb structure. iosxe-netflow "show ip interface" FMANRP_NETFLOW-4-NOSWIDB 4-Warning Sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a swidb structure. iosxe-netflow "show ip interface" FMANRP_PBR-3-INVALIDIF 3-Error The interface specified for '[chars]' is not valid An non-existent interface is specified for the policy based routing route-map operation specified in the message. iosxe-pbr "show interface" FMANRP_PBR-3-RTMAP_NAME_NULL 3-Error The route-map name for [chars] is NULL An unexpected condition has occurred due to the absence of an internal route-map data structure. iosxe-pbr "show route-map" FMANRP_PBR-3-RTMAPNULL 3-Error The route-map structure for [chars] is NULL An unexpected condition has occurred due to the absence of an internal route-map data structure. iosxe-pbr "show route-map" FMANRP_PBR-3-UNSUPPORTED_RMAP 3-Error Route-map [chars] has unsupported options for Policy-Based Routing. It has been removed from the interface if applied. - - - FMANRP_PBR-3-UNSUPPORTED_RMAP_COMMAND 3-Error This Policy-Based Routing command is not supported on this platform. Use the no form of this command to remove it from configurations Policy-Based Routing is not supported on this platform hardware "Remove this command" FMANRP_PBR-3-UNSUPPORTED_RMAP_SET_INTF 3-Error Route-map [chars] has unsupported options for Policy-Based Routing and has been removed from the interface if applied. \set interface [chars]\ is not a supported interface type for route-map. - - - FMANRP_PBR-3-UNSUPPORTED_RMAP_SET_SAME_INTF 3-Error Route-map [chars] has unsupported options for Policy-Based Routing and has been removed from the interface if applied. \set interface [chars]\ cannot be the same interface where route-map is being applied [chars]. The route-map attached to an interface for policy routing contains an action that is not supported on this platform. This is a hardware limitation. hardware "Reconfigure the route-map. Use only 'permit' " "entries and 'set ip next-hop' action in the " "route-map." FMANRP_PFR-4-NOINTF 4-Warning PfR Interface [chars] not exist can't be [chars] An unexpected condition has occurred which is due to the absence of\n\ MCP PfR interface info. iosxe-pfr "show oer border" FMANRP_PFR-4-NULLINPUT 4-Warning NULL input [chars] An unexpected condition has occurred which is due to the NULL value\n\ of the input parameter. iosxe-pfr "show oer border" FMANRP_PFR-4-UNSUPPORTED 4-Warning Unsupported action [chars] An unexpected condition has occurred which is due to and unsupported action being executed. iosxe-pfr "show oer border" FMANRP_QOS-3-ACTNOCLASSMAP 3-Error Class-map information not found An unexpected condition has occured when trying to determine class-map information for one of the classes in a policy-map. asr1k-qos "show policy-map" FMANRP_QOS-3-ACTNOPOLICYMAP 3-Error Policy-map information not found An unexpected condition has occured when trying to determine policy-map information for one of the service policies attached to an interface. asr1k-qos "show policy-map" FMANRP_QOS-3-CHILDPOLICYCHECK 3-Error Only 2 level policy is supported.\n\ Service-policy : [chars] Error occured while attaching a hierarchical policy polaris-qos LOG_STD_ACTION FMANRP_QOS-3-CLPOLFAIL 3-Error No support for client policy with policing in class-default and marking in custom class An internal error occured during installing qos policy. polaris-qos LOG_STD_ACTION FMANRP_QOS-3-CONFACTCHECK 3-Error Conform-action in a policer can only be transmit.\n\ Policy Rejected. Error occured while performing conform action\n\ check on the policer. polaris-qos LOG_STD_ACTION FMANRP_QOS-3-HIERPOLICYCHECK 3-Error Hierarchical Policy must have child under all user defined\n\ classes for wired ports. Service-policy : [chars] Error occured while attaching a hierarchical policy polaris-qos LOG_STD_ACTION FMANRP_QOS-3-HWIDBCHECK 3-Error Configuring service-policy on interface [chars] is not allowed Error occured while attaching policy on gigethernet0/0. polaris-qos LOG_STD_ACTION FMANRP_QOS-3-MARKDOWNCHECK 3-Error Only markdown with a table-map is supported. Error occured while performing exceed\n\ action check on the policy attached polaris-qos LOG_STD_ACTION FMANRP_QOS-3-NOACCOUNTSTATS 3-Error account stats entry not found for class [dec].[dec] target [dec] An internal error occured when looking up account\n\ statistics. asr1k-qos "show policy-map interface" FMANRP_QOS-3-NOPOLICERSTATS 3-Error policer stats entry not found for class [dec].[dec] target [dec] An internal error occured when looking up policer\n\ statistics. asr1k-qos "show policy-map interface" FMANRP_QOS-3-NOSETSTATS 3-Error set stats entry not found for class [dec].[dec] target [dec] An internal error occured when looking up set\n\ statistics. asr1k-qos "show policy-map interface" FMANRP_QOS-3-PRILEVELSUPPORT 3-Error Priority with level 3 is not supported.\n\ Service-policy : [chars] Priority level 3 support is only for AVB policy.\n\ Hence configuration is rejected. polaris-qos LOG_STD_ACTION FMANRP_QOS-3-QBUFFERSCHECK 3-Error Sum of configured qbuffer ratios should be less than 100.\n\ Configuration not accepted. Service-policy : [chars]\n\ Info : classes for which qbuffer ratio is not configured\n\ is given a buffer ratio 1 Error occured while performing queue buffers\n\ policy install check. Wrong configuration polaris-qos LOG_STD_ACTION FMANRP_QOS-3-QOSAPIPARAM 3-Error Internal QOS API error. An internal API error occured. QOS configuration may be limited. asr1k-qos LOG_STD_SH_TECH_ACTION FMANRP_QOS-3-QOSCLASSDEL 3-Error Error trying to remove class [chars] from policymap [chars] An operation to remove a class from a policy \n\ has failed due to an internal error. asr1k-qos "show policy-map" FMANRP_QOS-3-QOSGIDBSP 3-Error Service policy [[chars]] installation error: invalid interface type [dec] An invalid interface type was encountered when trying to configure a service policy. This service policy could not be installed. asr1k-qos "show policy-map" FMANRP_QOS-3-QOSIDBSP 3-Error Service policy [[chars]] installation error: invalid interface type [dec] An invalid interface type was encountered when trying to configure a service policy. This service policy could not be installed. asr1k-qos "show policy-map" FMANRP_QOS-3-QOSTDLMARSHAL 3-Error Failed to copy more than [dec] bytes of message [chars] length [dec] into IPC buffer An internal error occured when trying to build an IPC message. asr1k-qos LOG_STD_ACTION FMANRP_QOS-3-QOSTMPLCREATEFAIL 3-Error QoS template interface creation failed for policy [chars]: [chars] An error occured during template interface creation ewlc-qos LOG_STD_ACTION FMANRP_QOS-3-QOSTMPLDBERROR 3-Error Failed to [chars] record for policymap [chars] err [chars] Database operation failed for record of the policymap ewlc-qos LOG_STD_ACTION FMANRP_QOS-3-QOSTMPLDELETEFAIL 3-Error QoS template interface deletion failed for policy [chars]: [chars] An error occured during template interface deletion ewlc-qos LOG_STD_ACTION FMANRP_QOS-3-QOSTMPLINUSE 3-Error [chars]: [chars] record of the policymap is already in use ewlc-qos LOG_STD_ACTION FMANRP_QOS-3-QOSTMPLNONEXIST 3-Error QoS template does not exist in [chars] for policymap [chars] QoS template information does not exist ewlc-qos LOG_STD_ACTION FMANRP_QOS-3-SHAPEBWSUPPORT 3-Error Shape and bandwidth in the same class is unsupported.\n\ Policy Rejected. Service-policy : [chars] Error occured while performing qos policy check. polaris-qos LOG_STD_ACTION FMANRP_QOS-4-CLMODIFYFAIL 4-Warning classmap [chars] is currently used by policymap please remove policymap from all targets before the modification An internal error occured when classmap being modified asr1k-qos LOG_STD_ACTION FMANRP_QOS-4-COPPMODIFY 4-Warning Police rate modification for COPP system class [chars] is discouraged. User modified police rate for COPP system classes. accsw-p-qos LOG_STD_ACTION FMANRP_QOS-4-COPPMODRANGE 4-Warning Police rate modification for COPP system class [chars] is out-of-range. User modified police rate for COPP system classes. accsw-p-qos LOG_STD_ACTION FMANRP_QOS-4-COPPREMOVE 4-Warning Police rate removal for COPP system class [chars] is discouraged. User removed police rate for COPP system classes. accsw-p-qos LOG_STD_ACTION FMANRP_QOS-4-MPOLCHECK 4-Warning \nOnly class-default shaper in flat policy-map on parent interface [chars] can co-exist with Qos on sub targets QoS attaching validation check for MPOL qfp-qos LOG_STD_ACTION FMANRP_QOS-4-MPOLCHECKDETAIL 4-Warning \nOnly class-default shaper in flat policy-map on parent interface [chars] can co-exist with QoS on sub targets\n so policy-map [chars] on parent interface and its sub policy-maps all failed to attach please check it. QoS attaching validation check for MPOL qfp-qos LOG_STD_ACTION FMANRP_QOS-4-MPOLDMVPNGRE 4-Warning Only Shape and/or BRR is allowed on the QoS policy on GRE tunnel on MPoL hierarchy An error occurred during MPoL check between DMVPN and GRE tunnel QoS policy asr1k-qos LOG_STD_ACTION FMANRP_QOS-4-NOFAIRQONVC 4-Warning fair-queue can not be configured on the parent queue of an ATM VC use child queue instead Configuring fair-queue on the parent queue of an ATM VC is not supported asr1k-qos LOG_STD_ACTION FMANRP_QOS-4-QIDGENFAIL 4-Warning qid generation failed reverting to default An internal error occured during platform qos \n\ initialization. asr1k-qos LOG_STD_ACTION FMANRP_QOS-4-QOSSTACK 4-Warning Failed to install all classes for policymap [chars] excessive stack usage An operation to configure the classes within a policymap \n\ has failed due to a resource issue. QoS configuration\n\ for this policymap is unlikely to work. asr1k-qos "show policy-map" FMANRP_QOS-4-QOSUBR 4-Warning qos can not be attached to the target with UBR configured An error occured to attach qos to ATM VC/VP\n\ target with UBR configured asr1k-qos LOG_STD_ACTION FMANRP_QOS-4-STACKBUFFER 4-Warning Stack-buffer configuration has been modified. Current setting is stack-buffer [chars]. This change will take an effect once the configuration is written in flash write memory and then reload the switch. Stack-buffer configurations in Catalyst 9300D switches. accsw-p-qos LOG_STD_ACTION FMANRP_QOS-6-BUFFERSHARE 6-Information The QoS share-buffer is [chars]. Traffic might be impacted momentarily due to policy reattachment. QoS unified buffer configurations in CAT9K switches. accsw-p-qos LOG_STD_ACTION FMANRP_QOS-6-QOSCLASSEXIST 6-Information class [chars] id [dec] in policymap [chars] id [dec] already exists This is an informational message and no action \n\ is required. asr1k-qos "show policy-map" FMANRP_QOS-7-QOSEVPNPOLICYCHECK 7-Debug Unsupported QoS policy format in policy: [chars] QoS policy validation check for EVPN policy accsw-p-qos LOG_STD_ACTION FMANRP_QOS-7-QOSPROFILE 7-Debug The QoS profile has been modified to [chars]. The QoS policy-map's counters may not be updated accurately during the modification. QoS profile configurations in CAT9K switches. accsw-p-qos LOG_STD_ACTION FMANRP_SC-3-BULKSNTDLMSGMARSHAL 3-Error Failed to copy Bulk SN Entry message to IPC buffer This operation to build a TDL message for Bulk SN Entry \n\ has failed. iosxe-service_controller LOG_STD_ACTION FMANRP_SC-3-DBGTDLMSGMARSHAL 3-Error Failed to copy debug SC request message to IPC buffer This operation to build a TDL message for debug SC command \n\ has failed. iosxe-service_controller LOG_STD_ACTION FMANRP_SC-3-INTFTDLMSGMARSHAL 3-Error Failed to copy interface config message to IPC buffer for \n\ Interface [chars] 0x[hec] operation [chars] This operation to build a TDL message for interface configuration\n\ has failed. iosxe-service_controller LOG_STD_ACTION FMANRP_SC-3-SCIOSDENQUEUE 3-Error Failed to enqueue SC [chars] message for transmission This operation to enqueue an IPC message for sending has failed. iosxe-service_controller LOG_STD_ACTION FMANRP_SC-3-SCTXTDLMSGMARSHAL 3-Error Failed to copy service context config message to IPC buffer for\n\ sctx_name id [dec] This operation to build a TDL message for service context \n\ configuration has failed. iosxe-service_controller LOG_STD_ACTION FMANRP_SC-4-NOSERVICECTX 4-Warning A mapping structure is null An unexpected condition has occurred which is due to the absence of\n\ a SC mapping structure. iosxe-service_controller LOG_STD_SH_CMD_ACTION FMANRP_SC-4-SCBADACTION 4-Warning Invalid action [dec] for SC configuration An unexpected condition has occurred which is invalid action \n\ for a SC configuration. iosxe-service_controller LOG_STD_SH_CMD_ACTION FMANRP_SC-4-SCNOSWIDB 4-Warning Sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a swidb structure. iosxe-service_controller "show ip interface" FMANRP_SSLVPN-3-AAATDLERR 3-Error [chars][chars]. [chars] An unexpected condition has occurred in processing AAA request/reply message causing AAA handling failure. iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-CFGSTATUSERR 3-Error [chars]: [chars] An unexpected condition has occurred when got status of\n\ configuration iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-CONDDEBERR 3-Error [chars]. [chars] An unexpected condition has occurred in processing conditional debug message iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-GWERR 3-Error Failed [chars]: [chars] An unexpected condition has occurred in configuration processing \n\ causing configuration failure. iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-PKIERR 3-Error Failed [chars]: [chars] An unexpected condition has occurred in configuration processing \n\ causing configuration failure. iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-RRICHUNKERR 3-Error [chars] Error has occurred when requested memory for SSLVPN route handling iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-RRITDLERR 3-Error [chars][chars]. [chars] An unexpected condition has occurred in processing of SSLVPN route inject/remove message iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-STATSCLEARERR 3-Error Unable to send clear WEB VPN context stats message. [chars] [dec] This operation to build a TDL messages for WEB VPN context stats \n\ clearing has failed. iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-STATSGUPDERR 3-Error Update WEB VPN context stats error. [chars] [dec] An unexpected condition has occurred when updating global sslvpn \n\ statistics iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-STATSWVUPDERR 3-Error [chars]: [chars] An unexpected condition has occurred when updating ssl web vpn \n\ context statistics iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-3-VWCONFERR 3-Error Failed [chars]: [chars] An unexpected condition has occurred during WebVPN Context configuration\n\ causing failure. iosxe-sslvpn LOG_STD_ACTION FMANRP_SSLVPN-4-AAAFRIPWARN 4-Warning [chars]Invalid framed ip address [inet] received from AAA. Not sending user config Wrong AAA server config. iosxe-sslvpn LOG_STD_ACTION FMANRP_VRF-3-API_FAILED 3-Error NULL A call to the API of another component has indicated an\n\ error. iosxe-nat LOG_STD_ACTION FMANRP_VRF-3-EINVAL 3-Error NULL An unexpected input value to a function was incorrect iosxe-nat LOG_STD_ACTION FMANRP_VRF-3-ENOMEM 3-Error NULL Not enough memory memory pre allocation failed picasso-infra LOG_STD_ACTION FMCORE-2-ACL_FAILURE 2-Critical Interface [chars] traffic will not comply with ACLs in [chars] directions ACLs will not be applied on traffic for this interface due to TCAM\n\ resource contention. fm "The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention." FMCORE-2-VACL_FAILURE 2-Critical Interface [chars] traffic will not comply with VACLs in [chars] directions VACLs will not be applied on traffic for this interface due to TCAM\n\ resource contention. fm "The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention." FMCORE-4-RACL_REDUCED 4-Warning Interface [chars] routed traffic will be software switched in [chars] direction TCAM resource contention prevents ACLs from being applied in the TCAM\n\ for this interface. The traffic on this interface will be sent to\n\ software in order that the ACLs can be applied. fm "The configured ACLs are too large to all fit in the hardware TCAM.\n\ Use mls tcam priority command to prioritize interfaces for hardware\n\ switching. Try and share the same ACLs across multiple interfaces\n\ in order to reduce TCAM resource contention." FMCORE-6-RACL_ENABLED 6-Information Interface [chars] routed traffic is hardware switched in [chars] direction Earlier TCAM resource contention may have prevented ACLs from being applied in the TCAM for this interface. It has been enabled and traffic on this interface is hardware switched. fm "No need to take an action for this as it is an informational" "message not an error message." FMD_ISSU-2-GET_BUFFER 2-Critical FMD ISSU client failed to get buffer for message. Error: [dec] [chars] The FMD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show logging and show checkpoint client" FMD_ISSU-2-GET_BUFFER 2-Critical FMD ISSU client failed to get buffer for message. Error: [dec] [chars] The FMD ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show logging and show checkpoint client" FMD_ISSU-2-INIT 2-Critical FMD ISSU client initialization failed to [chars]. Error: [dec] [chars] The FMD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. medianet-metadata LOG_STD_ACTION FMD_ISSU-2-INIT 2-Critical FMD ISSU client initialization failed to [chars]. Error: [dec] [chars] The FMD ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. medianet-metadata LOG_STD_ACTION FMD_ISSU-2-SEND_NEGO_FAILED 2-Critical FMD ISSU client failed to send negotiation message. Error: [dec] [chars] The FMD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show logging and show checkpoint client" FMD_ISSU-2-SEND_NEGO_FAILED 2-Critical FMD ISSU client failed to send negotiation message. Error: [dec] [chars] The FMD ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show logging and show checkpoint client" FMD_ISSU-2-SESSION_NEGO 2-Critical FMD ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The FMD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show issu session and " "show issu negotiated capability " FMD_ISSU-2-SESSION_NEGO 2-Critical FMD ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The FMD ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. medianet-metadata "show issu session and " "show issu negotiated capability " FMD_ISSU-2-SESSION_REGISTRY 2-Critical FMD ISSU client failed to register session information. Error: [dec] [chars] The FMD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. medianet-metadata "show issu capability entries and " "show issu session and " "show issu negotiated capability " FMD_ISSU-2-SESSION_REGISTRY 2-Critical FMD ISSU client failed to register session information. Error: [dec] [chars] The FMD ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. medianet-metadata "show issu capability entries and " "show issu session and " "show issu negotiated capability " FMD_ISSU-3-CAP_INVALID_SIZE 3-Error FMD ISSU client capability list is empty. The FMD ISSU client capability exchange list size is invalid. medianet-metadata "show issu capability entires " FMD_ISSU-3-CAP_INVALID_SIZE 3-Error FMD ISSU client capability list is empty. The FMD ISSU client capability exchange list size is invalid. medianet-metadata "show issu capability entires " FMD_ISSU-3-CAP_NOT_COMPATIBLE 3-Error FMD ISSU client capability exchange result incompatible. The FMD ISSU client capability exchange have negotiated as incompatible with the peer. medianet-metadata "show issu negotiated capability " FMD_ISSU-3-CAP_NOT_COMPATIBLE 3-Error FMD ISSU client capability exchange result incompatible. The FMD ISSU client capability exchange have negotiated as incompatible with the peer. medianet-metadata "show issu negotiated capability " FMD_ISSU-3-INVALID_SESSION 3-Error FMD ISSU client does not have a valid registered session. The FMD ISSU client does not have a valid registered session. medianet-metadata "show issu capability entries and " "show issu session and " "show issu negotiated capability " FMD_ISSU-3-INVALID_SESSION 3-Error FMD ISSU client does not have a valid registered session. The FMD ISSU client does not have a valid registered session. medianet-metadata "show issu capability entries and " "show issu session and " "show issu negotiated capability " FMD_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER 3-Error 'Message Type [dec]' is not supported by FMD ISSU client at peer The FMD ISSU client at the peer supervisor is not compatible for this message type. The FMD client will be marked as incompatible with the peer. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-MSG_NOT_COMPATIBLE_WITH_PEER 3-Error 'Message Type [dec]' is not supported by FMD ISSU client at peer The FMD ISSU client at the peer supervisor is not compatible for this message type. The FMD client will be marked as incompatible with the peer. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-MSG_NOT_OK 3-Error FMD ISSU client 'Message Type [dec]' is not compatible The FMD ISSU client received an incompatible message from the peer device. The message cannot be processed. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-MSG_NOT_OK 3-Error FMD ISSU client 'Message Type [dec]' is not compatible The FMD ISSU client received an incompatible message from the peer device. The message cannot be processed. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-MSG_SIZE 3-Error FMD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The FMD ISSU client failed to calculate the MTU for the specified message. The FMD ISSU client is not able to send the message to the standby device. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-MSG_SIZE 3-Error FMD ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The FMD ISSU client failed to calculate the MTU for the specified message. The FMD ISSU client is not able to send the message to the standby device. medianet-metadata "show issu message group and " "show issu session and " "show issu negotiated version " FMD_ISSU-3-SESSION_UNREGISTRY 3-Error FMD ISSU client failed to unregister session information. Error: [dec] [chars] The FMD ISSU client failed to unregister session information. medianet-metadata "show issu session and " "show issu negotiated capability " FMD_ISSU-3-SESSION_UNREGISTRY 3-Error FMD ISSU client failed to unregister session information. Error: [dec] [chars] The FMD ISSU client failed to unregister session information. medianet-metadata "show issu session and " "show issu negotiated capability " FMD_ISSU-3-TRANSFORM_FAIL 3-Error FMD ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The FMD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the FMD state between the active device and the standby device is not identical. medianet-metadata "show issu session and " "show issu negotiated version " FMD_ISSU-3-TRANSFORM_FAIL 3-Error FMD ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The FMD ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the FMD state between the active device and the standby device is not identical. medianet-metadata "show issu session and " "show issu negotiated version " FMD-1-MALPINITFAILED 1-Alert MAL process failed creation System is going through a software error and has failed to create a process - LOG_STD_SH_TECH_ACTION FMD-1-MALPINITFAILED 1-Alert MAL process failed creation System is going through a software error and has failed to create a process - LOG_STD_SH_TECH_ACTION FMD-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the FMD feature failed. This will cause the feature to not function. qfp-fmd "This is normally a software issue. " "The consequences are that the FMD feature will not function. " LOG_STD_ACTION FMD-3-DBINITFAILED 3-Error Database Init failed This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to resource unavailability the INIT would have been failed.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-DBINITFAILED 3-Error Database Init failed This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to resource unavailability the INIT would have been failed.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-DELETENODEFAILED 3-Error Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple to delete the node It might because the Table is not populated for the flow \n The flow would have been deleted \n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-DELETENODEFAILED 3-Error Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple to delete the node It might because the Table is not populated for the flow \n The flow would have been deleted \n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper FMD software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-fmd "This is normally a software issue. " LOG_STD_RECUR_ACTION FMD-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper FMD software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck binding that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-fmd "This is normally a software issue. " LOG_STD_RECUR_ACTION FMD-3-LOOKUPFAILED 3-Error Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple It might because the Table is not populated for the flow \n The flow would have been deleted \n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-LOOKUPFAILED 3-Error Lookup failed for the flow of source_ip: [dec] dest_ip: [dec] source_port: [dec] dest_port: [dec] l4_protocol: [dec] class_id: [dec] vrf_table_id: [dec] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n This entry is not present in the Flow Table for the 4 Tuple It might because the Table is not populated for the flow \n The flow would have been deleted \n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-MEMALLOCFAILED 3-Error Memory Allocation failed This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n The memory might be full due to Flow Limit Exceeded.\n The Memory Leak would have happened.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-MEMALLOCFAILED 3-Error Memory Allocation failed This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n The memory might be full due to Flow Limit Exceeded.\n The Memory Leak would have happened.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-NULL 3-Error System receieved an invalid NULL pointer This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-NULL 3-Error System receieved an invalid NULL pointer This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-TRANSPORT 3-Error Operation [chars] on transport layer failed due to [chars] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FMD-3-TRANSPORT 3-Error Operation [chars] on transport layer failed due to [chars] This message can occur for the following unrelated reasons. Each reason is accompanied by a recommended action.\n Due to a software error.\n - "If none of the previous actions fix the problem copy the error " "message exactly as it appears and report it to your Cisco " "technical support representative." FME_DP-3-DEBUG_REG_FAILED 3-Error Flow Metric Engine fails to registrate with Conditional Debugging. Flow Metric Engine fails to registrate with Conditional Debugging infra. asr1k-avc LOG_STD_ACTION FME-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the FME feature failed. This will cause the feature to not function. qfp-mmon "This is normally a software issue. " "The consequences are that the FME feature will not function. " LOG_STD_ACTION FME-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper FME software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-mmon "This is normally a software issue. " LOG_STD_RECUR_ACTION FME-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper FME software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-mmon "This is normally a software issue. " LOG_STD_RECUR_ACTION FMEA-4-DS_JIB_ERRLOG 4-Warning DS JIB Santana FPGA Err log [chars] [chars] DS JIB Santana FPGA FMEA failure log cmts-infra "Minor non-fatal recoverable failure event" FNF_PROXY-3-EVAL_FREC_FIELD_LIST 3-Error Failed with return code: [dec] Netflow failed to process an evaluate flow record field list request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_FORCE_TEMPLATE_REFRESH 3-Error Failed with return code: [dec] Netflow failed to force a template refresh for an exporter. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_INIT 3-Error Failed with return code: [dec] Netflow failed to initialize the exporter. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_OPTION_TEMPLATE_BIND 3-Error Failed for exporter: [hec] with return code: [dec] Netflow failed to bind an option template. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_OPTION_TEMPLATE_UNBIND 3-Error Failed for exporter: [hec] with return code: [dec] Netflow failed to unbind an option template. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_OPTION_TIMER_START 3-Error Failed for exporter: [hec] with return code: [dec] Netflow failed to start an option timer. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_OPTION_TIMER_STOP 3-Error Failed for exporter: [hec] with return code: [dec] Netflow failed to stop an option timer. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-EXPORTER_SHUT 3-Error Failed with return code: [dec] Netflow failed to shutdown the exporter. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-FLOW_CACHE_WALK 3-Error Failed for session: [hec] with return code: [dec] Netflow failed to process a flow cache walk request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-FLOW_CACHE_WALK_FLEXIBLE 3-Error Failed for session: [hec] with return code: [dec] Netflow failed to process a flow cache walk/flexible request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-FNF_CWALK_TOP_TALKERS_INVALID_SORT 3-Error This field can't be used for sort Show Top Talkers command contains sort field specification that is not supported. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-IPC_UNHANDLED 3-Error type [dec] An unknown message was received by the Netflow Client Proxy. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_AGER_INIT 3-Error Failed with return code: [dec] Netflow failed to initialize the ager. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_AGER_SHUT 3-Error Failed with return code: [dec] Netflow failed to shutdown the ager. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_CLEAN 3-Error Failed with return code: [dec] Netflow failed to perform cache cleanup. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_FORCE_FLUSH 3-Error Failed with return code: [dec] Netflow failed to force a cache flush. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_FREE_LIST_INIT 3-Error Failed with return code: [dec] Netflow failed to initialize the free list. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-MON_CACHE_FREE_LIST_POOL_ADD 3-Error Failed with return code: [dec] Netflow failed to populate the free list. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-OBJ_MODIFY 3-Error Failed with return code: [dec] Netflow failed to process an object modify request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-PROCESS_FREC_FIELD_LIST 3-Error Failed with return code: [dec] Netflow failed to process a process flow record field list request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-PROXY_IPC_PAK_ALLOC_FAILED 3-Error - Allocation of IPC packet failed. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error [dec] Could not send IPC reply for proxy request. cpp-ucode LOG_STD_ACTION FNF_PROXY-3-STATS 3-Error Failed with return code: [dec] Netflow failed to process a stats request. cpp-ucode LOG_STD_ACTION FNF-3-CFT_REG_FAILED 3-Error FNF fails to connect to CFT infra. FNF fails to connect to CFT infra. cpp-ucode LOG_STD_ACTION FNF-3-CLEANUP_ENTRY 3-Error Failed Netflow failed to clean up a record for reuse. cpp-ucode LOG_STD_ACTION FNF-3-DEBUG_REG_FAILED 3-Error FNF fails to registrate with Conditional Debugging. FNF fails to registrate with Conditional Debugging infra. cpp-ucode LOG_STD_ACTION FNF-3-FNF_CWALK_FLEXIBLE_UNEXPECTED_LAYOUT 3-Error Failed copy to CLI buffer PI will receive zero buffer Failed copy to CLI buffer during the walk process fill the buffer with 0 cpp-ucode LOG_STD_ACTION FNF-3-FNF_EXPORT_BUILD_TYPE_FAILED 3-Error Format: [dec] FNF Exporter build failed. unknown type. cpp-ucode - FNF-3-FNF_FIELD_LIST_MEM_INSUFFICIENT 3-Error Insufficient memory [dec] for field_list Internal error netflow client provided insufficient memory to process a field list cpp-ucode LOG_STD_ACTION FNF-3-FNF_FIELD_LIST_TOO_LARGE 3-Error Field_list too large max [dec] Netflow field list contains too many fields. At most 32 fields are supported including any hidden fields automatically added as necessary for record keeping cpp-ucode LOG_STD_ACTION FNF-3-FNF_FIELD_LIST_TS_CNT_KEY 3-Error Field_id [dec] must be non-key Netflow Field list specified timestamp/counter field as a key field which is not supported cpp-ucode LOG_STD_ACTION FNF-3-FNF_FIELD_LIST_VAR_INVALID 3-Error Unknown field variety [dec] for field_id [dec] Internal error Netflow field list entry mapped to unknown field variety cpp-ucode LOG_STD_ACTION FNF-3-FNF_FIELD_UNEXPECTED_SIZE 3-Error Unexpected size for field_id [dec] expected [dec]/got [dec] Netflow specified unexpected size for field_id cpp-ucode LOG_STD_ACTION FNF-3-FNF_FREC_LAYOUT_TOO_LARGE 3-Error Flow record layout too large max [dec] Netflow field list results in a flow record layout which is too large. At most 128 bytes of flow record data is supported including any padding and any hidden fields automatically added as necessary for record keeping cpp-ucode LOG_STD_ACTION FNF-3-FNF_UNSUPPORTED_AGG_FMT 3-Error Format: [dec] Netflow doesn't support this aggregation type. cpp-ucode LOG_STD_ACTION FNF-3-FNF_UNSUPPORTED_EXP_FMT 3-Error Format: [dec] Netflow doesn't support this export format. cpp-ucode LOG_STD_ACTION FNF-3-FNF_UNSUPPORTED_MMA_FIELD 3-Error MMA global ID [dec] Netflow field [dec] is not supported by MMA - - - FNF-3-FNF_UNSUPPORTED_OPTION 3-Error Option: [dec] Netflow doesn't support this export option. cpp-ucode LOG_STD_ACTION FNF-3-FREE_LIST_ADD 3-Error Failed for record: 0x[hec] Netflow failed to return a record to the free list. cpp-ucode LOG_STD_ACTION FNF-3-INVALID_CMD 3-Error Flow builder encountered an invalid command: [dec]. Flow builder doesn't support the command encountered in the instruction stream. cpp-ucode LOG_STD_ACTION FNF-3-INVALID_FO 3-Error FNF FO is not valid FNF feature object is not valid. cpp-ucode LOG_STD_ACTION FNF-3-IPFIX_UNSUPPORTED_MON_TYPE 3-Error Monitor type: [dec] IPFIX doesn't support this monitor type. cpp-ucode LOG_STD_ACTION FNF-3-KEY_SIZE_INVALID 3-Error Unexpected key fields size: [dec] Netflow attempted to install a flow with an invalid key fields size. cpp-ucode LOG_STD_ACTION FNF-3- LC_STATUS 3-Error Flow monitor [chars] can not be added to [chars] rejected on module [chars] : [chars] The flow monitor has been rejected on the specified module. It will have been removed from the RP configuration too. This can happen for example when a monitor is removed and added again immediately before the tidy has been completed or in the case where a flow monitor is waiting at automore when the monitor is removed from the interface then reapplied flexible-netflow "Check the configuration of the Flow Monitor that" " was applied for errors. If the rejection was" " due to the LC not having finished cleaning up after" " a previous removal of a Flow Monitor wait until" " the cleaning up has finished then reapply the" " config." FNF-3- LC_STATUS 3-Error Flow monitor [chars] can not be added to [chars] rejected on module [chars] : [chars] The flow monitor has been rejected on the specified module. It will have been removed from the RP configuration too. This can happen for example when a monitor is removed and added again immediately before the tidy has been completed or in the case where a flow monitor is waiting at automore when the monitor is removed from the interface then reapplied flexible-netflow "Check the configuration of the Flow Monitor that" " was applied for errors. If the rejection was" " due to the LC not having finished cleaning up after" " a previous removal of a Flow Monitor wait until" " the cleaning up has finished then reapply the" " config." FNF-3- PROVISIONING 3-Error [chars] failed to provision '[chars] flow monitor [chars] [chars]' on [chars]: [chars] The attachment of the Flow Monitor to has had a problem on the device identified. It may be working on other devices and the configuration is retained. flexible-netflow "Check the device identified is working as expected" " and that it can support the configuration of the" " Flow Monitor to the chosen attachment point." FNF-3- PROVISIONING 3-Error [chars] failed to provision '[chars] flow monitor [chars] [chars]' on [chars]: [chars] The attachment of the Flow Monitor to has had a problem on the device identified. It may be working on other devices and the configuration is retained. flexible-netflow "Check the device identified is working as expected" " and that it can support the configuration of the" " Flow Monitor to the chosen attachment point." FNF-3-REFCNT_TIMEOUT 3-Error never reached 0 for entry [hec] Netflow timed out waiting for an flow cache entries refcnt. to hit 0. The entry was forced out cpp-ucode LOG_STD_ACTION FNF-3-REFCNT_UNDERFLOW 3-Error refcnt underflow for entry [hec] Netflow error caused flow cache entry reference count to go negative. The decrement was rescinded cpp-ucode LOG_STD_ACTION FNF-3-UNSUPPORTED_PROT 3-Error [chars] This protocol is unsupported. cpp-ucode LOG_STD_ACTION FNF-4-FREE_LIST_EMPTY 4-Warning Monitor: 0x[hec] Netflow attempted to install a flow but no free flow records were available. cpp-ucode LOG_STD_ACTION FNF-6- AGER_OVERRIDE 6-Information Flow [chars] time modified by [chars] to [dec] The aging timer has been modified and may be different from configured value. flexible-netflow LOG_STD_NO_ACTION FNF-6- AGER_OVERRIDE 6-Information Flow [chars] time modified by [chars] to [dec] The aging timer has been modified and may be different from configured value. flexible-netflow LOG_STD_NO_ACTION FNF-6- CONFIGURATION 6-Information Invalid FNF configuration: [chars] An invalid FNF configuration was detected. flexible-netflow "Review the FNF configuration before repeating the action." FNF-6- CONFIGURATION 6-Information Invalid FNF configuration: [chars] An invalid FNF configuration was detected. flexible-netflow "Review the FNF configuration before repeating the action." FNF-6-DYNAMIC_MONITORS_OVER_SUBSCRIPTION 6-Information Interface [chars] dir=[chars]: the number of monitors that should run on QFP maximum supported number of monitors per packet was exceeded. As a result the excess number of monitors will not run on the packet. Static monitors always take priority over policy-map monitors. cpp-ucode LOG_STD_DBG_ACTION FNF-6- ERROR 6-Information FNF error: [chars] An FNF error occurred. flexible-netflow "For more information repeat the action with FNF debugging enabled." FNF-6- ERROR 6-Information FNF error: [chars] An FNF error occurred. flexible-netflow "For more information repeat the action with FNF debugging enabled." FNF-6-SYNC_CACHE_TOO_MANY_RECS_FOR_INTERVAL 6-Information For synchronized cache the number of records is larger than can be exported in configured interval. The number of records is too large for the configured interval. As a result some records may not be exported in a timely manner. Consider reducing cache size or increasing interval length. cpp-ucode LOG_STD_DBG_ACTION FORCE_RPR-3-PEER_OPER_MODE 3-Error Peer node has reset [dec] times. [chars] The peer node has reset the maximum number allowed before reaching STANDBY-HOT state. The 'redundancy force-rpr' command is enabled and will try to set the peer system to RPR operating mode. redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FORCE_RPR-3-PEER_OPER_MODE 3-Error Peer node has reset [dec] times. [chars] The peer node has reset the maximum number allowed before reaching STANDBY-HOT state. The 'redundancy force-rpr' command is enabled and will try to set the peer system to RPR operating mode. redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FORCE_RPR-3-RF_REGISTER 3-Error RF error = [dec]. [chars] During system initialization Force RPR component was unable to register with the Redundancy Facility. redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FORCE_RPR-3-RF_REGISTER 3-Error RF error = [dec]. [chars] During system initialization Force RPR component was unable to register with the Redundancy Facility. redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FORCE_RPR-4-NOT_ON_ACTIVE 4-Warning [chars] Only the Active node may enable this feature. Make sure you're on the Active system before trying to enable this command redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FORCE_RPR-4-NOT_ON_ACTIVE 4-Warning [chars] Only the Active node may enable this feature. Make sure you're on the Active system before trying to enable this command redundancy-rf LOG_STD_ACTION FORCE_RPR_STD_ACTION FPD_MGMT-2-CREATE_FAIL 2-Critical Couldn't create [chars]. The system does not have enough free main memory to create the specified resource. spa-infra-fpd FPD_NO_FREE_MEMORY_STD_ACTION FPD_MGMT-2-CREATE_FAIL 2-Critical Couldn't create [chars]. The system does not have enough free main memory to create the specified resource. - FPD_NO_FREE_MEMORY_STD_ACTION FPD_MGMT-3-BNDL_CARD_TYPE_MISMATCH 3-Error The [chars] file does not contain the card type [hex] in the image bundle The image bundle in the indicated file does not contain a correct card type value for the target card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_CARD_TYPE_MISMATCH 3-Error The [chars] file does not contain the card type [hex] in the image bundle The image bundle in the indicated file does not contain a correct card type value for the target card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_CRC_CHECK_FAIL 3-Error The [chars] file contains a corrupted image bundle - CRC mismatch: current value [hex] expected value [hex]. Please make sure that this is a valid FPD image [chars] file for card in [chars]. The file failed the CRC checking process. This failure indicates a corrupt FPD image bundle or package file. spa-infra-fpd "Try to download again the required package from the Cisco " "Software Center website as the indicated one might be corrupted. " "If the problem persists copy the error message exactly as it appears " "and gather the output of the show hw-module subslot fpd" " show upgrade fpd table and " "show upgrade fpd file fpd-pkg-url commands " "then contact your technical support representative with the gathered " "information." FPD_MGMT-3-BNDL_CRC_CHECK_FAIL 3-Error The [chars] file contains a corrupted image bundle - CRC mismatch: current value [hex] expected value [hex]. Please make sure that this is a valid FPD image [chars] file for card in [chars]. The file failed the CRC checking process. This failure indicates a corrupt FPD image bundle or package file. - "Try to download again the required package from the Cisco " "Software Center website as the indicated one might be corrupted. " "If the problem persists copy the error message exactly as it appears " "and gather the output of the show hw-module subslot fpd" " show upgrade fpd table and " "show upgrade fpd file fpd-pkg-url commands " "then contact your technical support representative with the gathered " "information." FPD_MGMT-3-BNDL_NAME_PREFIX_MISMATCH 3-Error The [chars] file contains a bundle name prefix [chars] that does not match The content of the selected FPD image bundle does not match its filename. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_NAME_PREFIX_MISMATCH 3-Error The [chars] file contains a bundle name prefix [chars] that does not match The content of the selected FPD image bundle does not match its filename. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_HDR_LEN 3-Error The [chars] file contains wrong header length for the image bundle: [dec] bytes expected [dec] bytes. Please make sure that this is a valid The indicated file might not be a valid FPD image bundle or package file for the target card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_HDR_LEN 3-Error The [chars] file contains wrong header length for the image bundle: [dec] bytes expected [dec] bytes. Please make sure that this is a valid The indicated file might not be a valid FPD image bundle or package file for the target card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_MAGIC_NUM 3-Error The [chars] file contains a wrong magic number for the image bundle: [hex] expected [hex]. Please make sure that this is a valid FPD image [chars] The indicated file might not be a valid FPD image bundle or package file for the target card or the file could be corrupted. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_MAGIC_NUM 3-Error The [chars] file contains a wrong magic number for the image bundle: [hex] expected [hex]. Please make sure that this is a valid FPD image [chars] The indicated file might not be a valid FPD image bundle or package file for the target card or the file could be corrupted. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_SIZE 3-Error The [chars] file contains incorrect image bundle size: [dec] bytes expected [dec] bytes. Please make sure that this is a valid FPD image [chars] file The indicated file might not be a valid FPD image bundle or package file for the target card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BNDL_WRONG_SIZE 3-Error The [chars] file contains incorrect image bundle size: [dec] bytes expected [dec] bytes. Please make sure that this is a valid FPD image [chars] file The indicated file might not be a valid FPD image bundle or package file for the target card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BUNDLE_EXTRACT_ERROR 3-Error Cannot extract the [chars] bundle from [chars] - [chars] Bundle file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-BUNDLE_EXTRACT_ERROR 3-Error Cannot extract the [chars] bundle from [chars] - [chars] Bundle file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-CARD_DISABLED 3-Error [chars] card in [chars] is being disabled because of an incompatible FPD image version. Note that the [chars] package will be required if you want to perform the upgrade operation. The indicated card contains an incompatible FPD image version and is being disabled to avoid operational problems with the existing Cisco IOS software. This can happen if the automatic upgrade feature has not been enabled with the upgrade fpd auto global configuration command or if the automatic upgrade operation failed to perform the required upgrade or because it could not find the necessary FPD image package file. The incompatible image will need to be upgraded in order for the system to enable the card. spa-infra-fpd "The FPD image upgrade can be performed automatically by making sure that " "the automatic upgrade feature is enabled with the upgrade fpd " "auto global configuration command and the necessary FPD image " "package file is located in the system's default filesystem e.g. disk0: " FPD_MGMT-3-CARD_DISABLED 3-Error [chars] card in [chars] is being disabled because of an incompatible FPD image version. Note that the [chars] package will be required if you want to perform the upgrade operation. The indicated card contains an incompatible FPD image version and is being disabled to avoid operational problems with the existing Cisco IOS software. This can happen if the automatic upgrade feature has not been enabled with the upgrade fpd auto global configuration command or if the automatic upgrade operation failed to perform the required upgrade or because it could not find the necessary FPD image package file. The incompatible image will need to be upgraded in order for the system to enable the card. - "The FPD image upgrade can be performed automatically by making sure that " "the automatic upgrade feature is enabled with the upgrade fpd " "auto global configuration command and the necessary FPD image " "package file is located in the system's default filesystem e.g. disk0: " FPD_MGMT-3-CLOSE_FAILED 3-Error Failed to close [chars] file. FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-CLOSE_FAILED 3-Error Failed to close [chars] file. FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-DUPLICATE_UPGRADE_RESULT 3-Error Upgrade result already received for the FPD image upgrade of FPD ID [dec] for [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-DUPLICATE_UPGRADE_RESULT 3-Error Upgrade result already received for the FPD image upgrade of FPD ID [dec] for [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-FPD_UPGRADE_CANCELED 3-Error Rest of the FPD upgrade sequence for [chars] card in [chars] has been canceled due to upgrade failure with [chars] FPD ID=[dec] image. The FPD image upgrade process for additional FPD images has been canceled due to upgrade error in the indicated device. spa-infra-fpd "Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "show hw-module subslot fpd and contact your " "technical support representative with the gathered information." FPD_MGMT-3-FPD_UPGRADE_CANCELED 3-Error Rest of the FPD upgrade sequence for [chars] card in [chars] has been canceled due to upgrade failure with [chars] FPD ID=[dec] image. The FPD image upgrade process for additional FPD images has been canceled due to upgrade error in the indicated device. - "Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "show hw-module subslot fpd and contact your " "technical support representative with the gathered information." FPD_MGMT-3-FPD_UPGRADE_FAILED 3-Error [chars] FPD ID=[dec] image upgrade for [chars] card in [chars] has FAILED. The FPD image upgrade process has failed for the indicated device. spa-infra-fpd "Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "show hw-module subslot fpd and contact your " "technical support representative with the gathered information." FPD_MGMT-3-FPD_UPGRADE_FAILED 3-Error [chars] FPD ID=[dec] image upgrade for [chars] card in [chars] has FAILED. The FPD image upgrade process has failed for the indicated device. - "Retry the upgrade operation again. If the affected card remains " "disabled by the system after attempts to retry the upgrade then copy " "the error message exactly as it appears and gather the output of " "show hw-module subslot fpd and contact your " "technical support representative with the gathered information." FPD_MGMT-3-IMG_CRC_CHECK_FAILED 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file is corrupted - CRC The image failed the CRC checking process this indicates a corrupt FPD image bundle or package file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-IMG_CRC_CHECK_FAILED 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file is corrupted - CRC The image failed the CRC checking process this indicates a corrupt FPD image bundle or package file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-IMG_DATA_UNCOMPRESS_ERROR 3-Error Could not uncompress [chars] FPD image for [chars] in [chars]. An error has been detected during the uncompress operation of the compressed FPD image data. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-IMG_DATA_UNCOMPRESS_ERROR 3-Error Could not uncompress [chars] FPD image for [chars] in [chars]. An error has been detected during the uncompress operation of the compressed FPD image data. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-IMG_VER_NOT_FOUND 3-Error FPD image version information is not available for [chars] card in [chars]. All the FPD images will be upgraded to recover from this error. The FPD image version information for the indicated card is not available because the system was not able to extract this information for all the FPDs in the card. This could be the result of a corrupted FPD image from a power failure. spa-infra-fpd FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-IMG_VER_NOT_FOUND 3-Error FPD image version information is not available for [chars] card in [chars]. All the FPD images will be upgraded to recover from this error. The FPD image version information for the indicated card is not available because the system was not able to extract this information for all the FPDs in the card. This could be the result of a corrupted FPD image from a power failure. - FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-INCOMP_BNDL_VER 3-Error The selected [chars] file contain an image bundle that has a version number that is incompatible for this IOS release - [chars]. Selected version = [dec].[dec] minimum compatible version = [dec].[dec]. Please make sure that this is a valid FPD image [chars] file for card in [chars]. The SPA type is [chars]. The version of the selected FPD image bundle does not contain a valid version number that is compatible for the IOS release. The major version number should be the same and the minor version number should be at least equal to the minimal required version. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INCOMP_BNDL_VER 3-Error The selected [chars] file contain an image bundle that has a version number that is incompatible for this IOS release - [chars]. Selected version = [dec].[dec] minimum compatible version = [dec].[dec]. Please make sure that this is a valid FPD image [chars] file for card in [chars]. The version of the selected FPD image bundle does not contain a valid version number that is compatible for the IOS release. The major version number should be the same and the minor version number should be at least equal to the minimal required version. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INCOMP_IMG_VER 3-Error Incompatible [chars] FPD ID=[dec] image version detected for [chars] card An incompatible FPD image version has been detected. The FPD image needs to be upgraded either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled. spa-infra-fpd FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-INCOMP_IMG_VER 3-Error Incompatible [chars] FPD ID=[dec] image version detected for [chars] card An incompatible FPD image version has been detected. The FPD image needs to be upgraded either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled. - FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-INVALID_IMAGE_SIZE 3-Error The [chars] FPD image from [chars] file does not have a valid image size: expected size = [dec] bytes actual size = [dec] bytes. The size of the indicated FPD image does not have the expected size. The FPD image bundle or package might not be a valid file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_IMAGE_SIZE 3-Error The [chars] FPD image from [chars] file does not have a valid image size: expected size = [dec] bytes actual size = [dec] bytes. The size of the indicated FPD image does not have the expected size. The FPD image bundle or package might not be a valid file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_IMG_FORMAT 3-Error Invalid image format '[chars]' detected for FPD ID=[dec]. The selected FPD image to upgrade the indicated field programmable device does not have the right image format that can be used by the system to perform the upgrade operation. spa-infra-fpd "Please check if the FPD image package used in the upgrade is for the " "correct platform. This can be checked by using the show upgrade " "fpd package default privileged EXEC command." FPD_MGMT-3-INVALID_IMG_FORMAT 3-Error Invalid image format '[chars]' detected for FPD ID=[dec]. The selected FPD image to upgrade the indicated field programmable device does not have the right image format that can be used by the system to perform the upgrade operation. - "Please check if the FPD image package used in the upgrade is for the " "correct platform. This can be checked by using the show upgrade " "fpd package default privileged EXEC command." FPD_MGMT-3-INVALID_IMG_VER 3-Error Invalid [chars] FPD ID=[dec] image version detected for [chars] card in [chars]. The indicated field programmable device contains an invalid version for the FPD image because the system was not able to extract this information from the indicated card. A failed upgrade attempt might have corrupted the FPD image identification on the device. spa-infra-fpd FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-INVALID_IMG_VER 3-Error Invalid [chars] FPD ID=[dec] image version detected for [chars] card in [chars]. The indicated field programmable device contains an invalid version for the FPD image because the system was not able to extract this information from the indicated card. A failed upgrade attempt might have corrupted the FPD image identification on the device. - FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-INVALID_PKG_FILE 3-Error The indicated file [chars] is not a valid FPD image package file - [chars] The file format does not appear to be a valid FPD image package. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_PKG_FILE 3-Error The indicated file [chars] is not a valid FPD image package file - [chars] The file format does not appear to be a valid FPD image package. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_PKG_FILE_SIZE 3-Error The indicated file [chars] does not have a valid FPD image package The file size of the indicated FPD image package does not meet the required minimum size. The file is too small to be a valid FPD image package file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_PKG_FILE_SIZE 3-Error The indicated file [chars] does not have a valid FPD image package The file size of the indicated FPD image package does not meet the required minimum size. The file is too small to be a valid FPD image package file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-INVALID_UPGRADE_RESULT 3-Error Invalid upgrade result '[dec]' received for the FPD image upgrade of [chars] FPD ID=[dec] for [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-INVALID_UPGRADE_RESULT 3-Error Invalid upgrade result '[dec]' received for the FPD image upgrade of [chars] FPD ID=[dec] for [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-IPC_FAILED 3-Error Failed to send IPC message to [chars] in [chars] - [chars] The system failed to send a message via IPC to the indicated card. The cause of the specific IPC failure is inicated in the message. spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-IPC_FAILED 3-Error Failed to send IPC message to [chars] in [chars] - [chars] The system failed to send a message via IPC to the indicated card. The cause of the specific IPC failure is inicated in the message. - LOG_STD_ACTION FPD_MGMT-3-MAJOR_VER_MISMATCH 3-Error Major image version mismatch detected with [chars] FPD ID=[dec] for [chars] card A major image version mismatch has been detected. This incompatibility will need to be resolved by doing an upgrade or downgrade operation either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled. spa-infra-fpd FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-MAJOR_VER_MISMATCH 3-Error Major image version mismatch detected with [chars] FPD ID=[dec] for [chars] card A major image version mismatch has been detected. This incompatibility will need to be resolved by doing an upgrade or downgrade operation either automatically or manually to make the card operational. If the automatic upgrade feature is not enabled or if the system cannot find the necessary FPD image package file then the card will be disabled. - FPD_VERSION_ERROR_STD_ACTION FPD_MGMT-3-MISSING_BUNDLE_ENTRY 3-Error Failed to find a matching entry in the programmable device bundle information table for [chars] in [chars]. Card type or HW version [dec].[dec] FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-MISSING_BUNDLE_ENTRY 3-Error Failed to find a matching entry in the programmable device bundle information table for [chars] in [chars]. Card type or HW version [dec].[dec] FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-MISSING_DEV_INFO 3-Error Could not find [chars] FPD ID=[dec] in the list of FPD IDs populated FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-MISSING_DEV_INFO 3-Error Could not find [chars] FPD ID=[dec] in the list of FPD IDs populated FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-MISSING_IMAGE 3-Error Could not find the required [chars] image FPD ID=[dec] and FPD version=[dec].[dec] compatible with HW version=[dec].[dec] from the [chars]-fpd.bndl bundle in [chars] The indicated FPD image bundle or package file might not be the correct one. IF this is a FPD image package file then an incompatible package file might have been renamed with a filename that matched with the one that the system is expecting for this Cisco IOS software release. You should never rename an FPD image package file name. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-MISSING_IMAGE 3-Error Could not find the required [chars] image FPD ID=[dec] and FPD version=[dec].[dec] compatible with HW version=[dec].[dec] from the [chars]-fpd.bndl bundle in [chars] The indicated FPD image bundle or package file might not be the correct one. IF this is a FPD image package file then an incompatible package file might have been renamed with a filename that matched with the one that the system is expecting for this Cisco IOS software release. You should never rename an FPD image package file name. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-OPEN_FAILED 3-Error Failed to open [chars] [chars]. Please make sure that the required file The system cannot access the required file from the indicated URL. spa-infra-fpd "Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed." FPD_MGMT-3-OPEN_FAILED 3-Error Failed to open [chars] [chars]. Please make sure that the required file The system cannot access the required file from the indicated URL. - "Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed." FPD_MGMT-3-OUT_OF_MEMORY 3-Error Could not allocate the required [dec] bytes of memory. The system does not have enough free main memory to download the bundle file. spa-infra-fpd FPD_NO_FREE_MEMORY_STD_ACTION FPD_MGMT-3-OUT_OF_MEMORY 3-Error Could not allocate the required [dec] bytes of memory. The system does not have enough free main memory to download the bundle file. - FPD_NO_FREE_MEMORY_STD_ACTION FPD_MGMT-3-PKG_FILE_SEARCH_FAILED 3-Error FPD image package [chars] cannot be found in system's flash card or By default if the upgrade fpd path fpd-pkg-url global configuration command is not configured then the system will try to locate the required FPD image package file from removable flash cards or disks that are accessible by the system for FPD upgrade. This message indicates that the system could not find the package file. spa-infra-fpd "Make sure that the indicated FPD image package file is copied into a " "flash card or disk that is accessible by the system then restart the " "FPD upgrade by reinsertion of the target card to the system or use of " "a system command to reload or power-cycle the target card." FPD_MGMT-3-PKG_FILE_SEARCH_FAILED 3-Error FPD image package [chars] cannot be found in system's flash card or By default if the upgrade fpd path fpd-pkg-url global configuration command is not configured then the system will try to locate the required FPD image package file from removable flash cards or disks that are accessible by the system for FPD upgrade. This message indicates that the system could not find the package file. - "Make sure that the indicated FPD image package file is copied into a " "flash card or disk that is accessible by the system then restart the " "FPD upgrade by reinsertion of the target card to the system or use of " "a system command to reload or power-cycle the target card." FPD_MGMT-3-PKG_VER_FILE_EXTRACT_ERROR 3-Error Cannot extract the [chars] version file from [chars] - [chars] Package version file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-PKG_VER_FILE_EXTRACT_ERROR 3-Error Cannot extract the [chars] version file from [chars] - [chars] Package version file extraction error. The cause of the failure is indicated in the error message. The indicated file might not be a valid FPD image package file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-PKG_VER_MISMATCH_NOTE 3-Error The FPD image package being used [chars] is not the right version for The indicated FPD image package that is being used in FPD automatic upgrade does not contain the correct version information for the IOS version that is running in the system. This condition can occur if a different version of the FPD image package was renamed to match the filename that the IOS image is expecting to use. The upgrade operation will still be performed by trying to find the required FPD image from the renamed package file. spa-infra-fpd "If the upgrade operation fails because the required FPD image cannot be " "found with the renamed FPD image package replace the wrong package " "file with a valid one and perform the upgrade operation again." FPD_MGMT-3-PKG_VER_MISMATCH_NOTE 3-Error The FPD image package being used [chars] is not the right version for The indicated FPD image package that is being used in FPD automatic upgrade does not contain the correct version information for the IOS version that is running in the system. This condition can occur if a different version of the FPD image package was renamed to match the filename that the IOS image is expecting to use. The upgrade operation will still be performed by trying to find the required FPD image from the renamed package file. - "If the upgrade operation fails because the required FPD image cannot be " "found with the renamed FPD image package replace the wrong package " "file with a valid one and perform the upgrade operation again." FPD_MGMT-3-READ_BNDL_HDR_ERROR 3-Error Failed to read the FPD bundle header from [chars] file. The indicated file might not be a valid FPD image bundle or package file. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-READ_BNDL_HDR_ERROR 3-Error Failed to read the FPD bundle header from [chars] file. The indicated file might not be a valid FPD image bundle or package file. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-READ_ERROR 3-Error Could not read the [chars] file. The system cannot read the required file from the indicated URL. spa-infra-fpd "Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed." FPD_MGMT-3-READ_ERROR 3-Error Could not read the [chars] file. The system cannot read the required file from the indicated URL. - "Make sure that the indicated URL is a valid path and the system " "has access to the filesystem where the file has been placed." FPD_MGMT-3-SEND_IMG_FAILED 3-Error [chars] FPD ID=[dec] image for [chars] card in [chars] has failed to be sent The FPD image was not able to be sent for the upgrade operation. The system might be too busy to handle this operation. The affected card will be disabled by this failure. spa-infra-fpd "Wait until the system load is lower to try again with the manual upgrade " "procedure by using the upgrade hw-module privileged " "EXEC command. If the symptom persists copy the error message " "exactly as it appears and gather the output of the show " "tech-support command and contact your technical support " "representative with the gathered information." FPD_MGMT-3-SEND_IMG_FAILED 3-Error [chars] FPD ID=[dec] image for [chars] card in [chars] has failed to be sent The FPD image was not able to be sent for the upgrade operation. The system might be too busy to handle this operation. The affected card will be disabled by this failure. - "Wait until the system load is lower to try again with the manual upgrade " "procedure by using the upgrade hw-module privileged " "EXEC command. If the symptom persists copy the error message " "exactly as it appears and gather the output of the show " "tech-support command and contact your technical support " "representative with the gathered information." FPD_MGMT-3-SW_ERROR 3-Error NULL FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-SW_ERROR 3-Error NULL FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-TOO_MANY_FPD_ENTRIES 3-Error Too many FPD entries for the FPD Bundle Info Table. Required number of entries = [dec] maximum number of entries allowed = [dec]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-TOO_MANY_FPD_ENTRIES 3-Error Too many FPD entries for the FPD Bundle Info Table. Required number of entries = [dec] maximum number of entries allowed = [dec]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-UNKNOWN_BNDL_HDR_FORMAT 3-Error Unknown header format version: [hex] FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-UNKNOWN_BNDL_HDR_FORMAT 3-Error Unknown header format version: [hex] FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-UPGRADE_LIST_FULL 3-Error Could not add a new entry in the FPD Management Upgrade List. No upgrade will be performed for the [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION spa-infra-fpd LOG_STD_ACTION FPD_MGMT-3-UPGRADE_LIST_FULL 3-Error Could not add a new entry in the FPD Management Upgrade List. No upgrade will be performed for the [chars] card in [chars]. FPD_INTERNAL_SW_ERR_STD_EXPLANATION - LOG_STD_ACTION FPD_MGMT-3-WRONG_IMG_DATA_LEN 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong data The indicated file might not be a valid FPD image bundle or package file for the card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_DATA_LEN 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong data The indicated file might not be a valid FPD image bundle or package file for the card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_HDR_LEN 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong header The indicated file might not be a valid FPD image bundle or package file for the card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_HDR_LEN 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong header The indicated file might not be a valid FPD image bundle or package file for the card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_MAGIC_NUM 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong magic The indicated file might not be a valid FPD image bundle or package file for the card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_MAGIC_NUM 3-Error The FPD image for [chars] FPD ID [dec] in [chars] file contains wrong magic The indicated file might not be a valid FPD image bundle or package file for the card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_MAJOR_VER 3-Error The selected FPD image for upgrade contains wrong FPD image major version number = '[dec]' expected number = '[dec]' for [chars] FPD ID [dec]. The file used for upgrade might not be a valid FPD image bundle or package file for the card. spa-infra-fpd FPD_WRONG_PKG_STD_ACTION FPD_MGMT-3-WRONG_IMG_MAJOR_VER 3-Error The selected FPD image for upgrade contains wrong FPD image major version number = '[dec]' expected number = '[dec]' for [chars] FPD ID [dec]. The file used for upgrade might not be a valid FPD image bundle or package file for the card. - FPD_WRONG_PKG_STD_ACTION FPD_MGMT-4-BYPASS_AUTO_UPGRADE 4-Warning The automatic FPD image upgrade feature is not enabled bypassing the image upgrade for [chars] card in [chars]. The automatic FPD image upgrade feature is not enabled. The incompatible image will not be automatically upgraded. The card will be disabled until the image is upgraded to a compatible version. spa-infra-fpd "Enable the automatic FPD image upgrade with the upgrade fpd " "auto global configuration command or use the upgrade " "hw-module privileged EXEC command for a manual upgrade " "operation. For more information about these commands refer to the " FPD_DOCUMENT_NAME "." FPD_MGMT-4-BYPASS_AUTO_UPGRADE 4-Warning The automatic FPD image upgrade feature is not enabled bypassing the image upgrade for [chars] card in [chars]. The automatic FPD image upgrade feature is not enabled. The incompatible image will not be automatically upgraded. The card will be disabled until the image is upgraded to a compatible version. - "Enable the automatic FPD image upgrade with the upgrade fpd " "auto global configuration command or use the upgrade " "hw-module privileged EXEC command for a manual upgrade " "operation. For more information about these commands refer to the " FPD_DOCUMENT_NAME "." FPD_MGMT-4-CFG_NOT_SYNCED 4-Warning Failed to sync \[chars]\ command to standby: [chars] A FPD configuration command failed to get synced to standby RP due to the indicated error condition. Usually this can happen if the standby RP hardware doesn't support the type of filesystem supported on the active one. spa-infra-fpd "Configure again the command with a filesystem that is supported on " "both standby and active RP. To find out if a specific filesystem is " "also supported on standby RP the dir ? command " "can be used to display a list of filesytem supported on both standby " "and active RP." FPD_MGMT-4-CFG_NOT_SYNCED 4-Warning Failed to sync \[chars]\ command to standby: [chars] A FPD configuration command failed to get synced to standby RP due to the indicated error condition. Usually this can happen if the standby RP hardware doesn't support the type of filesystem supported on the active one. - "Configure again the command with a filesystem that is supported on " "both standby and active RP. To find out if a specific filesystem is " "also supported on standby RP the dir ? command " "can be used to display a list of filesytem supported on both standby " "and active RP." FPD_MGMT-4-UPGRADE_EXIT 4-Warning Unexpected exit of FPD image upgrade operation for [chars] card in [chars]. The FPD image upgrade operation was interrupted by the physical removal of the card from the system or by the use of other commands that have interrupted the normal operation of the target card. The partial upgrade operation might have left the card unusable because of corrupted FPD images. spa-infra-fpd "If the card does not come up after reinserting into the system then " "perform the recovery upgrade operation by using the upgrade " "hw-module privileged EXEC command. With this command the " "system will attempt the reprogramming of the image to recover from the " "previous partial upgrade operation. For more information about " "performing a recovery upgrade operation refer to the " FPD_DOCUMENT_NAME "." FPD_MGMT-4-UPGRADE_EXIT 4-Warning Unexpected exit of FPD image upgrade operation for [chars] card in [chars]. The FPD image upgrade operation was interrupted by the physical removal of the card from the system or by the use of other commands that have interrupted the normal operation of the target card. The partial upgrade operation might have left the card unusable because of corrupted FPD images. - "If the card does not come up after reinserting into the system then " "perform the recovery upgrade operation by using the upgrade " "hw-module privileged EXEC command. With this command the " "system will attempt the reprogramming of the image to recover from the " "previous partial upgrade operation. For more information about " "performing a recovery upgrade operation refer to the " FPD_DOCUMENT_NAME "." FPD_MGMT-4-VERSION_CHECK_ABORTED 4-Warning FPD image version check operation has been aborted for [chars] card in [chars] because manual upgrade has already being started. The FPD image version check operation required for the automatic upgrade feature is not being performed for the indicated card because the upgrade hw-module privileged EXEC command has already being executed. These two operations cannot be performed at the same time. spa-infra-fpd "If an automatic upgrade operation is required do not enter the " "upgrade hw-module privileged EXEC command for the " "manual upgrade while the target card is initializing. Enter the " "show hw-module subslot fpd command and ensure that " "the target card is displayed in the command output before proceeding " "with the manual upgrade." FPD_MGMT-4-VERSION_CHECK_ABORTED 4-Warning FPD image version check operation has been aborted for [chars] card in [chars] because manual upgrade has already being started. The FPD image version check operation required for the automatic upgrade feature is not being performed for the indicated card because the upgrade hw-module privileged EXEC command has already being executed. These two operations cannot be performed at the same time. - "If an automatic upgrade operation is required do not enter the " "upgrade hw-module privileged EXEC command for the " "manual upgrade while the target card is initializing. Enter the " "show hw-module subslot fpd command and ensure that " "the target card is displayed in the command output before proceeding " "with the manual upgrade." FPD_MGMT-5-CARD_POWER_CYCLE 5-Notice [chars] card in [chars] is being power cycled for the FPD image upgrade to take effect. The indicated card is being power cycled after the FPD image upgrade. This action allows the target card to be operational with the new upgraded FPD image or images. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-5-CARD_POWER_CYCLE 5-Notice [chars] card in [chars] is being power cycled for the FPD image upgrade to take effect. The indicated card is being power cycled after the FPD image upgrade. This action allows the target card to be operational with the new upgraded FPD image or images. - LOG_STD_NO_ACTION FPD_MGMT-5-POST_UPGRADE_REMINDER 5-Notice [chars] card in [chars] will require a [chars] for the FPD image upgrade to take effect. The indicated card will require manual intervention after the FPD image upgrade. The specified operation is required for the upgraded FPD image to take effect. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-5-POST_UPGRADE_REMINDER 5-Notice [chars] card in [chars] will require a [chars] for the FPD image upgrade to take effect. The indicated card will require manual intervention after the FPD image upgrade. The specified operation is required for the upgraded FPD image to take effect. - LOG_STD_NO_ACTION FPD_MGMT-5-POSTPONE_POWER_CYCLE 5-Notice [chars] card in [chars] will be power cycled after bulk sync completion. Currently Bulk sync is in Progress. Once the new standby reaches HOT state the indicated card will be power cycled to be operational with the new upgraded FPD image. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-5-UPGRADE_ATTEMPT 5-Notice Attempting to automatically upgrade the FPD images for [chars] card The automatic FPD image upgrade feature is enabled with the upgrade fpd auto global configuration command. The system is currently upgrading an incompatible image version automatically. spa-infra-fpd "No action is required. The upgrade process can take a long time.The " "FPD_MGMT-6-UPGRADE_TIME message gives an estimate of the total " "upgrade time" FPD_MGMT-5-UPGRADE_ATTEMPT 5-Notice Attempting to automatically upgrade the FPD images for [chars] card The automatic FPD image upgrade feature is enabled with the upgrade fpd auto global configuration command. The system is currently upgrading an incompatible image version automatically. - "No action is required. The upgrade process can take a long time.The " "FPD_MGMT-6-UPGRADE_TIME message gives an estimate of the total " "upgrade time" FPD_MGMT-6-BUNDLE_DOWNLOAD 6-Information Downloading FPD image bundle for [chars] card in [chars] ... The system is downloading the field programmable device image bundle to the system main memory. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-BUNDLE_DOWNLOAD 6-Information Downloading FPD image bundle for [chars] card in [chars] ... The system is downloading the field programmable device image bundle to the system main memory. - LOG_STD_NO_ACTION FPD_MGMT-6-OVERALL_UPGRADE 6-Information All the attempts to upgrade the required FPD images have been completed for [chars] card in [chars]. Number of successful/failure upgrades: All the FPD image upgrades have completed for the indicated card. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-OVERALL_UPGRADE 6-Information All the attempts to upgrade the required FPD images have been completed for [chars] card in [chars]. Number of successful/failure upgrades: All the FPD image upgrades have completed for the indicated card. - LOG_STD_NO_ACTION FPD_MGMT-6-PENDING_UPGRADE 6-Information [dec] more FPD image upgrade operation will be required on [chars] in [chars] after additional power-cycle operation on the target card. All upgrade operations have not completed and additional power-cycle operations are required before the upgraded or new FPD image will be applied to the system configuration. The message text indicates the number of pending upgrade operations that will be performed. More than one power-cycle operation might be required to complete the overall upgrade process. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-PENDING_UPGRADE 6-Information [dec] more FPD image upgrade operation will be required on [chars] in [chars] after additional power-cycle operation on the target card. All upgrade operations have not completed and additional power-cycle operations are required before the upgraded or new FPD image will be applied to the system configuration. The message text indicates the number of pending upgrade operations that will be performed. More than one power-cycle operation might be required to complete the overall upgrade process. - LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_PASSED 6-Information [chars] FPD ID=[dec] image in the [chars] card in [chars] has been successfully The FPD image upgrade process has completed successfully for the indicated device. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_PASSED 6-Information [chars] FPD ID=[dec] image in the [chars] card in [chars] has been successfully The FPD image upgrade process has completed successfully for the indicated device. - LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_RETRY 6-Information Attempting to recover from the failed upgrades ... Because of an image upgrade failure the system will attempt again the upgrade operation for the same FPD image. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_RETRY 6-Information Attempting to recover from the failed upgrades ... Because of an image upgrade failure the system will attempt again the upgrade operation for the same FPD image. - LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_START 6-Information [chars] FPD ID=[dec] image upgrade in progress for [chars] card in [chars]. The FPD image upgrade process has started. Do not interrupt the upgrade operation as any interruption could render the target card unusable. Avoid actions like removing the target card from the system powering off the system or using commands that can power-cycle the target card during the upgrade process. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_START 6-Information [chars] FPD ID=[dec] image upgrade in progress for [chars] card in [chars]. The FPD image upgrade process has started. Do not interrupt the upgrade operation as any interruption could render the target card unusable. Avoid actions like removing the target card from the system powering off the system or using commands that can power-cycle the target card during the upgrade process. - LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_TIME 6-Information Estimated total FPD image upgrade time for [chars] card in [chars] = %TS. The estimated total time for all FPD images to be upgraded is displayed for the indicated card. spa-infra-fpd LOG_STD_NO_ACTION FPD_MGMT-6-UPGRADE_TIME 6-Information Estimated total FPD image upgrade time for [chars] card in [chars] = %TS. The estimated total time for all FPD images to be upgraded is displayed for the indicated card. - LOG_STD_NO_ACTION FR_EEK-5-FAILED 5-Notice Interface [chars] - DLCI [dec] The end-to-end keepalive protocol has failed for the indicated PVC. A failure occurs when the DLCI is ACTIVE and end-to-end keepalives are enabled but the number of errors due to timeouts or sequence number mismatches has reached the failure threshold. The DLCI is taken out of operation until the protocol recovers. fr "A persistent failure may indicate a mismatched end-to-end keepalive " "configuration at each end of the PVC. A transient failure may be due " "to a temporary loss of connectivity or heavy congestion in the network. " "This is a rate-limited log message so not all failures may be logged. " "The show frame-relay end-to-end keepalive failures " "command can be used to obtain further information on what PVCs have " "experienced failures." FR_ELMI-3-INCORRECT_ID 3-Error Incorrect ID Incorrect ID in QOS parameter message. - "" FR_ELMI-3-INCORRECT_IE 3-Error Incorrect IE Enhanced LMI is not configured on the interface. The frame was dropped. - "" FR_FRAG-3-BADPAK 3-Error Inconsistent packet: size [dec] linktype [chars] input [chars] output [chars] A packet being fragmented has inconsistent size and data fr "Inform Cisco technical support representative" FR_HA -3-ISSU 3-Error [chars]: [chars] A Frame Relay ISSU error occurred. fr LOG_STD_SH_TECH_ACTION FR_HA -3-SYNC 3-Error [chars]: code [dec] An error occurred when syncing Frame Relay state to the Standby Route Processor. This may affect Non-Stop Forwarding capability on Frame Relay interfaces during and after switchover until the state is recovered through normal protocol operation. fr "Reset the standby processor to attempt the sync again. " LOG_STD_RECUR_ACTION FR_LC_XDR-3-PULL_SEND_ERROR 3-Error Error occurred sending FR PVC stats to the RP: error code [dec] An error occurred while updating the RP with FR PVC stats.\n\ Some of the FR PVC counters may be inaccurate. fr "Some FR PVC stats may be lost. This may be a temporary failure.\n\ If ths error message continues to be seen please contact Cisco TAC" FR_LC_XDR-3-UNIT_SZ_TOO_BIG 3-Error Error occurred sending FR PVC stats to the RP: [chars]: DLCI [dec]: unit sz [dec] An error occurred while updating the RP with FR PVC stats.\n\ Some of the FR PVC counters may be inaccurate. fr "Some FR PVC stats may be lost. This may be a temporary failure.\n\ If ths error message continues to be seen please contact Cisco TAC" FR_LMI-3-INCORRECT_IE 3-Error Enhanced LMI not configured incorrect IE An unexpected LMI information element has been received. fr "Verify the configuration for enhanced LMI on the switch matches the c onfiguration on the router." FR_LMI-3-MSG_TOO_BIG 3-Error [chars] [chars] Status message too big status of PVCs with dlci values LMI STATUS message size is too big to fit into interface MTU. fr "LMI type - cisco - does not support segmentation of STATUS message " "so either increase the interface MTU or use LMI types - ansi or " "q933a." FR_RP_STATS-3-CORRUPT_MSG 3-Error FR IPC stats msg is corrupted: buffer [hec]: length [dec] An error occurred while processing a FR IPC stats message. \n\ Some of the FR PVC counters may be inaccurate. fr "This could be a temporary failure.\n\ But there could be a possibility that some of the FR PVC counters may\n\ not have updated correctly.\n\ If the error message is seen multiple times please inform Cisco \n\ technical support representative." FR_RP_STATS-3-INVALID_STAT_UNIT 3-Error Error processing FR IPC stats msg: DLCI is out of bounds An error occurred while processing a FR IPC stats message.\n\ Some of the FR PVC counters may be inaccurate. fr "This could be a temporary failure that may or may not affect the\n\ accuracy of PVC stats. If this error message continues to be seen\n\ multiple times please inform Cisco technical support representative." FR_RP_STATS-3-INVALID_UNIT_COUNT 3-Error FR IPC stats msg is corrupted: unit count [dec] An error occurred while processing a FR IPC stats message.\n\ Some of the FR PVC counters may be inaccurate. fr "This could be a temporary failure.\n\ But there could be a possibility that some of the FR PVC counters may\n\ not have updated correctly.\n\ If the error message is seen multiple times please inform Cisco \n\ technical support representative." FR_RP_XDR-3-CLIENT_INIT_ERROR 3-Error FR XDR client initialization error: error code [dec] An error occurred while registering the FR RP XDR client. \n\ Distributed packet forwarding over FR will not work. fr "This is a serious error. Without the FR XDR client distributed \n\ packet forwarding over FR will not work. Please inform a Cisco \n\ technical support representative" FR_RP_XDR-3-INTERFACE_SETUP_ERROR 3-Error Unable to setup FR XDR for interface [chars] An error occurred while setting up FR XDR for a FR interface.\n\ This will affect distributed packet forwarding over this interface. fr "This is a serious error. Without FR XDR support distributed \n\ packet forwarding over the FR interface in question will not work. \n\ Please inform a Cisco technical support representative" FR_VCB-3-ADJ_SRC_ERROR 3-Error Error sourcing adjacency - vc-bundle [chars] dlci [dec] An error occurred while setting up the adj for a member pvc fr "Try reconfiguring the vc-bundle" FR_VCB-3-BUMPING 3-Error Bumping error - vcb [chars] - [chars] An error occurred while bumping traffic in a vc-bundle fr "As a workaround reconfigure the vc-bundle to avoid bumping" FR_VCB-3-CONFIG 3-Error Configuration error - vcb [chars] - [chars] An error occurred while interpreting vc-bundle configuration fr "Try reconfiguring the vc-bundle" FR_VCB-3-FIBSW_MISSING_TABLE_ENTRY 3-Error FIB switching error - vc-bundle [chars] An error occurred while FIB switching packets across vc-bundle fr "As a workaround delete the vc-bundle and employ a PVC to substitute " "for the vc-bundle" FR_VCB-3-PROCESS_SWITCHING 3-Error Switching error - vcb [chars] - [chars] An error occurred while switching packets across vc-bundle fr "As a workaround delete the vc-bundle and employ a PVC to substitute " "for the vc-bundle" FR_VCB-5-UPDOWN 5-Notice FR VC-Bundle [chars] changed state to [chars] The state of a frame-relay vc-bundle changed to up/down fr "Notification message only. No action required" FR_VIP-3-INCONSISTENT 3-Error Invalid state on VIP: DLCI [dec]: Slot [dec]: Error code [dec] An error occurred while processing FR state on the VIP fr "Shut - no shut the frame-relay encapsulated interface for the" "slot in question" FR_VIP-3-MISSING_STATE 3-Error Missing state on VIP: DLCI [dec]: Slot [dec] An error occurred while preparing an IPC stats unit fr "Shut - no shut the frame-relay encapsulated interface for the" "slot in question" FR_VIP-3-SWITCHING 3-Error [chars] DLCI [dec]: [chars] An error was detected while switching a packet on the VIP fr "Shut - no shut of the interface in question or unconfigure then\n\ re-configure may solve the problem. Copy and save the message\n\ and call your technical support representative for assistance" FR_VIP-5-FLUSH 5-Notice Flushing frame relay state Clearing up frame relay state on the VIP card fr "Notification message only. No action required." FR-3-BQ_DEQ_ERR 3-Error fr_bq_proc: unknown packet on broadcast queue packet dropped! Invalid packet on FR broadcast queue packet dropped! fr "If the router or some features are not operational due to this" "condition attempt to disable the Frame Relay broadcast queue by " "entering the no frame-relay broadcast-queue" "command in interface configuration mode for a immediate workaround." "And "LOG_STD_ACTION FR-3-BQ_DEQ_PTR 3-Error fr_br_proc: hdr-[hec] size-[dec] dlci-%4x %8x %8x The Frame Relay broadcast queue contains a datagram that is invalid. The packet has been dropped. fr "Inform Cisco technical support representative" FR-3-BQ_ENQ_ERR 3-Error fr_oqueue: Invalid datagramstart [hec] [hec] pak dropped A broadcast packet was detected in the Frame Relay output queue that contained an invalid datagram header. The packet has been dropped. fr "If the router or some features are not operational due to this" "condition attempt to disable the Frame Relay broadcast queue by " "entering the no frame-relay broadcast-queue" "command in interface configuration mode for a immediate workaround." "And "LOG_STD_ACTION FR-3-FR_INV_OUTPUT_VECTOR 3-Error An invalid output vector detected on interface [chars] An invalid internal function vector is installed on a Frame Relay interface which affects the ability of processing outbound traffic on the device. fr "Remove and re-apply Frame Relay encapsulation on the interface to " "recover from the error." FR-3-FR_PVC_STATUS_Q_CREATE_ERROR 3-Error FR PVC status event queue error: failed to create queue Unable to create FR PVC status event queue fr LOG_STD_ACTION FR-3-FRTSZEROCIR 3-Error FRTS: attempt to configure zero CIR It should not be possible to configure a zero CIR. To do so would prevent data transmission on the VC. fr "Inform Cisco technical support representative" FR-3-MAP_DELETE_ERROR 3-Error [chars] An error occurred while deleting a frame-relay map fr LOG_STD_ACTION FR-3-MFR_UNEXPECTEDEVENT 3-Error MFR Timer process error: event table is NULL for event [dec] state [dec] The event was ignored because the state transition table is NULL. Normal processing continue. fr "Please refer to Bug Toolkit on CCO to check for existing bugs. " "If you need further assistance please provide 'show version' and " "'show running' and any configurations that were being done at the " "time the message was seen. Copy the message text exactly as it " "appears on the console or in the system log. Inform Cisco technical " "support representative and provide the representative with the " "gathered information." FR-3-MLPOFR_ERROR 3-Error MLPoFR not configured properly on Link [chars] Bundle [chars] :[chars] The configuration of MLPPP-over-Frame-Relay MLPoFR fr "Ensure that FRTS has been configured on physical interface and that " "the service policy has been attached to the Virtual Template. To " "verify the configuration use the show running-config serial " "inteface and show running-config " "virtual-template commands." FR-3-NOMEMORY 3-Error No memory for [chars] The requested operation could not be accomplished because of a low memory condition. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." FR-3-NULL_PTR_DEREF 3-Error Dereferencing NULL pointer [chars] Dereferencing a NULL pointer fr "Inform Cisco technical support representative" FR-3-SVC_SETUP 3-Error [chars]: interface [chars]: DLCI [dec] An error occurred while attempting to setup a Frame-Relay SVC. There may have been an attempt to setup a SVC using a DLCI thats already in use fr "Check if the DLCI is already in use. For example: A PVC may be " "configured to use the same DLCI " "use show frame-relay pvc to verify. " FR-4-DLCIDELETE 4-Warning Interface [chars] - DLCI [dec] - PVC use count [dec] Trying to remove PVC DLCI while it is still being used. fr "If this error can be easily recreated enter the " "debug frame-relay event command and recreate " "the condition that caused this error. " "Copy all the debug messages text and the system message text " "exactly as it appears on the console or in the system log enter " "the show tech-support command contact your Cisco technical support " "representative and provide the representative with the gathered " "information." FR-4-NNISUBINTF 4-Warning Subinterface not supported on Frame Relay NNI Trying to change the state of a subinterface on FR NNI. fr "Reconfigure the Frame Relay link type or remove the subinterface." FR-5-CONVERT_ROUTE 5-Notice Converting route pair to connect A pair of Frame Relay routes are being converted to connections. - LOG_STD_NO_ACTION FR-5-DLCICHANGE 5-Notice Interface [chars] - DLCI [dec] state changed to [chars] The state of the Frame Relay PVC specified by the DLCI changed. fr "Notification message only. No action required." FRAG_DESC_PROXY-3-PROXY_IPC_FRAG_MEM_EXTEND_FAILED 3-Error - Increasing of fragment descriptor pool failed. cpp-ucode LOG_STD_ACTION FRAG_DESC_PROXY-3-PROXY_IPC_FRAG_MEM_INIT_FAILED 3-Error - Initialization of fragment descriptor pool failed. cpp-ucode LOG_STD_ACTION FRAG_DESC_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION FRAG_DESC_PROXY-3-PROXY_IPC_VFR_MEM_EXTEND_FAILED 3-Error - Increasing of vFR state pool failed. cpp-ucode LOG_STD_ACTION FRAG_DESC_PROXY-3-PROXY_IPC_VFR_MEM_INIT_FAILED 3-Error - Initialization of vFR state pool failed. cpp-ucode LOG_STD_ACTION FRAG_DESC_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Invalid IPC message subtype. cpp-ucode LOG_STD_ACTION FRAG-2-UNENABLED 2-Critical [chars] feature not enabled at interface [chars] packet cannot be processed Reassembly or fragmentation feature as indicated not enabled by the control plane. This is a critical problem. qfp LOG_STD_ACTION FRAG-3-FRAG_DESC_MEM_INIT_FAILED 3-Error - Failure occurred initializing fragment descriptor pool. qfp LOG_STD_ACTION FRAG-3-FRAG_DESC_MEM_REQ_FAILED 3-Error - IPC Failure occurred when attempting to request more fragment descriptor pool memory. qfp LOG_STD_ACTION FRAG-3-FRAG_STATE_MEM_INIT_FAILED 3-Error - Failure occurred initializing fragment state pool. qfp LOG_STD_ACTION FRAG-3-FRAG_STATE_MEM_REQ_FAILED 3-Error - IPC failure occurred when attempting to request more fragment state pool memory. qfp LOG_STD_ACTION FRAG-3-INVALID_MTU 3-Error [chars] feature failed at interface [chars] due to invalid L3 MTU %lu Fragmentation was not able to be performed due to invalid adj L3 MTU given by the control plane. qfp LOG_STD_ACTION FRAG-3-INVALID_QFP_NO 3-Error Invalid qfp device no.: [chars] Invalid qfp device no. qfp LOG_STD_ACTION FRAG-3-REASSEMBLY_DBG 3-Error Reassembly/VFR encountered an error: [chars] [chars] %lu [chars] %lu Reassembly/VFR encountered a runtime error as indicated in the message with parameter data for debug qfp LOG_STD_ACTION FRAG-3-REASSEMBLY_ERR 3-Error Reassembly/VFR encountered an error: [chars] Reassembly/VFR encountered a runtime error as indicated qfp LOG_STD_ACTION FRATM_RED-3-INTERNAL_CRITICAL 3-Error [chars] - - - FRATM_RED-3-INTERNAL_ERROR 3-Error [chars] - - - FRATM-2-INTERNAL_CRITICAL 2-Critical [chars] - - LOG_STD_SH_TECH_ACTION FRATM-3-CONFIG_ERROR 3-Error [chars] - - LOG_STD_SH_TECH_ACTION FRATM-3-INTERNAL_ERROR 3-Error [chars] - - LOG_STD_SH_TECH_ACTION FRATM-4-INTERNAL_WARNING 4-Warning [chars] - - LOG_STD_SH_TECH_ACTION FRDM336-3-ANYPHYALLOCFAILED 3-Error Anyphy allocation failed for [chars] Encountered an error while configuring the ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-BUNDLEEXIST 3-Error Unexpected bundle0x[hec] present in freedm Encountered an error while provisioning a bundle osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-BUNDLERANGE 3-Error bundle0x[hec] not within range Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-CC_RESEQ_FIFO_ACT_NOT_CLEAR 3-Error FRDM336 base addr 0x[hec]: Removing CI0x[hec] of channel Encountered an error in the ASIC of line card while unprovisioning a channel or Multilink interface. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' " "in Linecard and RP" FRDM336-3-CIALLOCFAILED 3-Error CI allocation failure for tag=[dec] dlciCos=[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-CITAGMISMATCH 3-Error CI0x[hec] does not belong to tag0x[hec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-DEFAULTCI 3-Error Unexpected default CI for channel 0x[hec] Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" FRDM336-3-DLCICOSRANGE 3-Error DLCICOS0x[hec] not within range Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" FRDM336-3-EQM_SIZE_NOT_ZERO 3-Error HDLC%04d : %#010x %#010x %#010x %#010x Encountered an error while configuring or unconfiguring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" FRDM336-3-INITERR 3-Error FRDM336 chip initialization failed errcode=[dec]: [chars] Required resources to initialize the ASIC in Linecard unavailable. This is normally due to hardware issue osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Reinsert the linecard. If still fails " "swap hardware and LOG_STD_SH_TECH_ACTION" FRDM336-3-INVALIDANYPHY 3-Error Anyphy0x[hec] number is not in range Encountered an error while configuring the ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP " "'show platform multilink' in Linecard" FRDM336-3-INVALIDCI 3-Error Either CI0x[hec] range not ok or not allocated Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-LLAPI_PROVERR 3-Error FRDM336 base addr 0x[hec]: Channel provisioning SBI no:[dec] SPE no:[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-LLINT_DET_TSMSKUSEERR 3-Error FRDM336 base addr 0x[hec]: TS mask in use SBI no:[dec] SPE no:[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-LLINT_TSMSKUSEERR 3-Error FRDM336 base addr 0x[hec]: TS mask in use SBI no:[dec] SPE no:[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-NCHUNKSNONZERO 3-Error FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec] Encountered an error in the ASIC of line card This mostly occurs while unprovisioning a channel or shuting interface. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-NCHUNKSNONZERO_CC_RESEQ_FIFO_ACT_SET 3-Error FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec] Encountered an error in the ASIC of line card This mostly occurs while unprovisioning a channel or shuting interface. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-NOANYPHYALLOCATED 3-Error No Anyphy number for channel=[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-NOCIALLOCATED 3-Error No CI number for tag=[dec] dlciCos=[dec] Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-PDDBNULL 3-Error Device data block null Encountered an error while accessing an ASIC in Linecard osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-3-POLLTO 3-Error FRDM336 indirect poll timeout. base addr:[hex] offset:[hex] value:[hex] mask:[hex] delay:[hex] Not able to access a register in the ASIC of Linecard this is normally hardware problem osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 LOG_STD_SH_TECH_ACTION FRDM336-3-PROVERR 3-Error FRDM336 Channel provisioning SBI no:[dec] SPE no:[dec] TRIB no:[dec] HDLC channel no:[dec] failed errcode=[dec]: [chars] Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in " "Linecard and RP" FRDM336-3-RHDL_TAVAIL_NOT_CLEAR 3-Error FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec] Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-SET_CHANPARAM_ERR 3-Error FRDM336 setting parameters of a Channel failed HDLC channel no:[dec] - osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in " "Linecard and RP" FRDM336-3-SET_SPE_ERR 3-Error FRDM336 setting configuration of SPE SBI no:[dec] SPE no:[dec] to [dec] failed Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-SET_TRIB_ERR 3-Error FRDM336 setting configuration of tributary SBI no:[dec] SPE no:[dec] TRIB no:[dec] to [dec] failed errcode=[dec]: [chars] Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-THDL_AVAIL_NOT_CLEAR 3-Error FRDM336 base addr 0x[hec]: disabling channelHDLC channel no:[dec] Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-3-TRIB_ENAB_DIS_ERR 3-Error FRDM336 [chars] tributary SBI no:[dec] SPE no:[dec] TRIB no:[dec] failed Encountered an error while configuring an ASIC in the Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "Collect the details that triggered the issue say like any " "config change switchover etc and then" LOG_STD_SH_TECH_ACTION FRDM336-5-NOBUNDLEPRESENT 5-Notice bundle0x[hec] not present in freedm Encountered an error while configuring an ASIC in Linecard. osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "'show controller' in Linecard and RP" "'show platform multilink' in Linecard" FRDM336-6-EQM_ML_INFO 6-Information ML%04d : %#010x %#010x %#010x %#010x Multilink information osm-ct3 for CT3 osm-choc-ds0 for CHOC-12/DS0 "No action is required" FREEDM-2-FATALEVENT 2-Critical Freedm [chars] fatal event occured: 0x[hec] A catastrophic Freedm error occured - "" FREEDM-3-BUSYTIMEOUT 3-Error Freedm [chars] busy bit of register 0x[hec] never cleared Driver timedout waiting for the Freedm to acknowlege a request - "" FREEDM-3-HDLC_ALLOC_FAIL 3-Error Freedm [chars]: Allocation of HDLC controller [dec] for channel [dec] failed Allocation of an HDLC controller failed - "" FREEDM-3-HDLC_INUSE 3-Error Freedm [chars]: HDLC controller [dec] already in use on channel [dec] An attempt was made to use an HDLC controller which was already in use - "" FREEDM-3-INITFAIL 3-Error Freedm [chars] initialization failed: [chars] Freedm device failed initialization - "" FREEDM-3-NOTFREEDM 3-Error Freedm [chars] returned device/vendor of [hex] PCI get device id returned an unrecognized value - "" FREEDM-3-REG_READ_TIME_OUT 3-Error Busy Out Error of FREEDM [dec] [chars] Trying to read FREEDM internal RAM Busy bit is still set for\n\ more than 10 seconds. as LOG_STD_SH_TECH_ACTION FRNTEND_CTRLR-1-MGR_TXQ_FULL 1-Alert The front end controller Tx queue reached watermark level The queue between microcontroller controlling the front end and IOS has reached the watermark level. Too many messages are pending in the queue firmware "Please try reloading the switch. If it does not fix the " "problem this could be a bad hardware. Contact the Cisco " "technical support representative" FRNTEND_CTRLR-1-RELOAD_REQD 1-Alert A UCODE upgrade has taken place without a reload. There must be a reload in order to complete the upgrade. Some features will not work properly until the reload is performed. The UCODE images were upgraded during an archive download software upgrade but the switch was not reloaded as part of the upgrade. The switch must be reloaded to complete the upgrade. Until the switch is reloaded PoE thermal power supply and stack-power features will not be completely supported. firmware "Please reload the switch at the earliest convenience." FRNTEND_CTRLR-2-SUB_INACTIVE 2-Critical The front end controller [dec] is inactive The microcontroller controlling the front end has become inactive. This controls the Port LEDs Uplink LEDs Power over ethernet and thermal/fan control functionality. These functionalities will not work on the ports controlled by this microcontroller. This does not have any impact on data traffic hardware "Please try a reset of the hardware. If it does not fix the " "problem this could be a bad hardware. Contact the Cisco " "technical support representative" FRR_OCE-3-GENERAL 3-Error [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-GENERAL 3-Error [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_ADDRTYPE 3-Error addrtype to xdr: [dec] [dec] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_ADDRTYPE 3-Error addrtype to xdr: [dec] [dec] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_EVT 3-Error Error in BFD event retrieval bfd notification handle is %p session handle is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_EVT 3-Error Error in BFD event retrieval bfd notification handle is %p session handle is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_HNDL 3-Error [chars] bfd notification handle is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_HNDL 3-Error [chars] bfd notification handle is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_SESSION 3-Error BFD session db node mismatch: bfd context db node is %p frr db node is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALID_BFD_SESSION 3-Error BFD session db node mismatch: bfd context db node is %p frr db node is %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALIDPAR 3-Error Parent OCE %p[chars] is [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-INVALIDPAR 3-Error Parent OCE %p[chars] is [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-NULLPOINTER 3-Error [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-3-NULLPOINTER 3-Error [chars] An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-4-ERROR_BFD_SESSION 4-Warning [chars]BFD returned [dec] for address [chars] and interface [chars] if_num: [dec] - node %p handle %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-4-ERROR_BFD_SESSION 4-Warning [chars]BFD returned [dec] for address [chars] and interface [chars] if_num: [dec] - node %p handle %p An internal software error occurred. OCE_DDTS_COMPONENT "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release." FRR_OCE-4-INVALID_BACKUP_OCE 4-Warning Invalid backup oce is found because interface %lu is removed or reloading The interface or line card is reloading or removed. OCE_DDTS_COMPONENT "Check whether the line card is present and the interface is up." FRR_OCE-4-INVALID_BACKUP_OCE 4-Warning Invalid backup oce is found because interface %lu is removed or reloading The interface or line card is reloading or removed. OCE_DDTS_COMPONENT "Check whether the line card is present and the interface is up." FRR_OCE-4-NULL_PRIMARY_OCE 4-Warning [chars] The interface or line card is reloading or pulled off. OCE_DDTS_COMPONENT "Check whether the line card is in online and the interface is up." FRR_OCE-4-NULL_PRIMARY_OCE 4-Warning [chars] The interface or line card is reloading or pulled off. OCE_DDTS_COMPONENT "Check whether the line card is in online and the interface is up." FRR_OCE-5-ISSULOG 5-Notice FRR is not ISSU compatible notified by [chars] MPLS failed to set offset within packet OCE_DDTS_COMPONENT LOG_STD_ACTION FRR_OCE-5-ISSULOG 5-Notice FRR is not ISSU compatible notified by [chars] MPLS failed to set offset within packet OCE_DDTS_COMPONENT LOG_STD_ACTION FRR-5-MPLS_TE 5-Notice ERRMSG_NOFLAGS - - - FRR-5-MPLS_TE 5-Notice ERRMSG_NOFLAGS - - - FRRMGR-3-FRRMGR_INTERNAL_ERR 3-Error [chars] FRRMGR_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION FRRMGR-3-FRRMGR_INTERNAL_ERR 3-Error [chars] FRRMGR_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION FS_IPHC-2-LC_IPHC_SETUP_FAIL 2-Critical Failed to initialise or allocate memory for IP Compression database. IP Compression main database not created due to lack of memory resources.\n\ iphc "The Line Card cannot allocate memory for an IP Compression database.\n\ Add more memory if possible to the VIP. \n\ Free up memory on the VIP by reducing features used or " "buffer allocations.\n\ Reduce the number of contexts configured on all interfaces on\n\ the affected line card using the interface configuration \n\ ip rtp compression-connections" FS_IPHC-2-LC_PROC_INIT 2-Critical LC Failed to initialise distributed IP Hdr Comp Process IP Compression Process not created on Line Card. iphc "A possible reason for a process failing to start is lack of resources.\n\ Check memory allocation on line card and either upgrade line card memory\n\ or reduce feature burden in it's interface configurations." FS_IPHC-2-RP_NOLCINFO 2-Critical Unable to malloc state table for LC An internal data structure is missing due to lack of memory resources. iphc "The Route Processor is dangerously low on memory resources. Free up \n\ memory by removing unwanted feature configuration or upgrade the memory\n\ on the system router processor" FS_IPHC-3-LC_INVALID_MSG 3-Error Received IPC message of unknown type IP compression on Line Card has received an unknown message from Route\n\ Processor. iphc "If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative." FS_IPHC-3-MSG_TOO_LARGE 3-Error Received IPC message too large to handle [dec] IP compression has received an IPC message of a size larger than expected.\n\ iphc "If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative." FS_IPHC-4-IPC_NO_CHUNK 4-Warning IPC Chunk pool empty slot [dec] VIP junked RSP msg IP compression private memory pool for IPC messages exhausted. iphc "If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative." FS_IPHC-4-LC_IPCSENDFAIL 4-Warning LC unable to send IPHC msg to RP [dec] Line card was unable to send an IP header compression \n\ information message to the route processor. iphc "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ip rtp head and debug ip tcp head\n\ commands for the period during which this message appeared." FS_IPHC-4-LC_NOIPCBUFFER 4-Warning Unable to malloc IPC msg buffer [dec] on line card Line card unable to send IPHC information to Route Processor due to lack\n\ of memory in it's private memory pool. iphc "If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative." FS_IPHC-4-RP_IPCSENDFAIL 4-Warning RP unable to send IPHC msg to LC [dec] Route processor was unable to send an IP header compression \n\ configuration message to a line card interface. iphc "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ip rtp head and debug ip tcp head\n\ commands for the period during which this message appeared." FS_IPHC-4-RP_NOIPCBUFFER 4-Warning Unable to malloc IPC msg buffer [dec] on RP Route Processor unable to send IPHC information to Line Card due to lack\n\ of memory in it's private memory pool. iphc "If this message occurs regularly copy the error message exactly as it\n\ appears and report it to your technical support representative." FTC_TRUNK-1-NOMEMORY 1-Alert msgtxt_nomemory The MPC860/PowerQUICC CPU was unable to access the memory it needs to carry out its functions. Here are some possible causes. The network is large requiring a lot of memory for routing tables and so on. The router configuration has many features enabled each of which require a certain amount of memory. A software error memory leak exists. - "Reduce system activity to ease the memory demand or upgrade to a larger memory configuration." FTC_TRUNK-1-RELOAD 1-Alert Must reload to config Interface [chars] as ftc-trunk again If the operator first configures an interface to 'encapsulation ftc-trunk' then re-configures it later to some other encapsulation such as HDLC then attempts to re-configure it again to 'encap ftc-trunk' then this error messages is displayed to notify the operator that the 'reload' command must be entered first before attempting to configure the interface to 'encap ftc-trunk' again. - "Issue the 'reload' command." FTC_TRUNK-3-CID_IN_USE 3-Error [chars] connection-id [dec] is busy try other cid When setting up a new session-trunk if the operator attempts to use a connection-ID that is already assigned and in-use then the error message is displayed to indicate that the selected connection-id cannot be used for this session-trunk. - "Try again with a connection-ID which is not already in use." FTC_TRUNK-3-TOOMANY 3-Error Cannot config more than [dec] ftc-trunks When the operator enters the 'encap ftc-trunk' configuration command if there are already 4 interfaces configured for encap ftc-trunk this message is displayed to indicate that no more can be configured. - "Free one of the other interfaces first or if conditions warrant upgrade to a larger configuration with more interfaces." FTC_TRUNK-3-TOOMANY_SESSION 3-Error Cannot config more than [dec] session-trunks When the operator enters the 'encap ftc-trunk' configuration command if there are already 4 interfaces configured for encap ftc-trunk then the message is displayed to indicate that no more can be configured. - "Free one of the existing interfaces before trying again or if conditions warrant upgrade to a larger configuration." FTP_ALG-3-BAD_L7_DATA 3-Error - Receive Bad L7 data from either FW or NAT. cpp-ucode LOG_STD_ACTION FTP_ALG-3-CHUNK_CREATE_FAIL 3-Error - Chunk create failed. FTP ALG will not be able to finish initialization. cpp-ucode LOG_STD_ACTION FTP_ALG-3-INCOMPATIBLE_HA_MSG_LEN 3-Error rcvd:[hec] expect:[hec] Incompatible HA Message Length. FTP ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP_ALG-3-INCOMPATIBLE_HA_VERSION 3-Error rcvd:[hec] expect:[hec] Incompatible HA Version. FTP ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP_ALG-3-INCORRECT_HA_MAGIC 3-Error rcvd:[hec] expect:[hec] Incorrect HA MAGIC. FTP ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP_ALG-3-INVALID_HA_OPCODE 3-Error rcvd:[hec] expect:[hec] Invalid HA opcode. FTP ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP_ALG-3-L7_DATA_CREATE_ERROR 3-Error - Error during L7 data creation. cpp-ucode LOG_STD_ACTION FTP_ALG-3-WRITEBACK_ERROR 3-Error - Error during writeback. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-BAD_L7_DATA 3-Error - Receive Bad L7 data from either FW or NAT. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-CHUNK_CREATE_FAIL 3-Error - Chunk create failed. FTP64 ALG will not be able to finish initialization. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-INCOMPATIBLE_HA_MSG_LEN 3-Error rcvd:[hec] expect:[hec] Incompatible HA Message Length. FTP64 ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-INCOMPATIBLE_HA_VERSION 3-Error rcvd:[hec] expect:[hec] Incompatible HA Version. FTP64 ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-INCORRECT_HA_MAGIC 3-Error rcvd:[hec] expect:[hec] Incorrect HA MAGIC. FTP64 ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-INVALID_HA_OPCODE 3-Error rcvd:[hec] expect:[hec] Invalid HA opcode. FTP64 ALG will reject sync data. cpp-ucode LOG_STD_ACTION FTP64_ALG-3-L7_DATA_CREATE_ERROR 3-Error - Error during L7 data creation. cpp-ucode LOG_STD_ACTION FTPSE-3-MSG_ERR 3-Error [chars] Error Messages pagent "try debug command" FTPSE-6-MSG_INF 6-Information [chars] Program information - - FTPSE-6-NETWRTFAILED 6-Information FTPSE Server:connection / tcp_write failed. A TCP write failed while sending an FTP command reply to the client. - "Verify network connection from client to server and verify ftp client operation." FTPSE-7-MSG_DBG 7-Debug [chars] Debug Messages - - FTPSERVER-4-XFER_WARNING 4-Warning File may not have transferred correctly Extra linefeeds were received in ASCII mode - - FTPSERVER-6-CONNCLOSED 6-Information Connection closed after [dec] seconds. '[chars]' The FTP connection to a client was closed after 5 minutes inactivity. - "Client inactivity will cause the server to shutdown the connection." FTPSERVER-6-CWDFAILED 6-Information setcwd failed [chars]. FTP client request failed to change to requested directory. - "Verify correct path for desired directory." FTPSERVER-6-NETRDFAILED 6-Information FTP control connection / tcp_read failed. An error occured reading the command line from the ftp client. - "Verify network connection from client to server and verify ftp client operation." FTPSERVER-6-NETWRTFAILED 6-Information FTP Server:connection / tcp_write failed. A TCP write failed while sending an FTP command reply to the client. - "Verify network connection from client to server and verify ftp client operation." FTPSERVER-6-NEWCONN 6-Information FTP Server - new connection made. An new ftp server connection has opened. - "FTP Server connections can be disabled by config 'no ftp-server enable'." FTPSERVER-6-REPLYLOGN 6-Information REPLY [dec] This is an informational message only.\n\ An FTP login has occurred. - "Informational messages can be disabled by changing logging level." FTPSERVER-6-REPLYLOGTEXT 6-Information [dec][chars] This is an informational message only.\n\ This text was sent to the FTP client. - "Informational messages can be disabled by changing logging level." FTPSERVER-6-TOPDIRTEST 6-Information Input path failed Top-dir[chars] test. An operation attempted to use a path not within the tree under the ftp-server topdir config parameter. - "Re-configure the server 'topdir' parameter or select another path." FTSP-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." FTSP-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." FTSP-2-INTERNAL_ERROR 2-Critical Internal software error. [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION FTSP-2-INTERNAL_ERROR 2-Critical Internal software error. [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION FTSP-4-FMAIL_FAILED_AUTHENTICATION 4-Warning Authentication for > [chars] < failed\n Authenticating the specified user failed - LOG_STD_RECUR_ACTION FTSP-4-FMAIL_FAILED_AUTHENTICATION 4-Warning Authentication for > [chars] < failed\n Authenticating the specified user failed - LOG_STD_RECUR_ACTION FTSP-4-FMAIL_NO_ACCOUNTING 4-Warning FAXMAIL- Accounting\n\for tty[dec] failed Accounting failed for the specified tty. - LOG_STD_RECUR_ACTION FTSP-4-FMAIL_NO_ACCOUNTING 4-Warning FAXMAIL- Accounting\n\for tty[dec] failed Accounting failed for the specified tty. - LOG_STD_RECUR_ACTION FTSP-4-HARDWARE_ERROR 4-Warning tty [dec] A hardware interface was not configured when a fax call was\n\ answered or attempted. - LOG_STD_RECUR_ACTION FTSP-4-HARDWARE_ERROR 4-Warning tty [dec] A hardware interface was not configured when a fax call was\n\ answered or attempted. - LOG_STD_RECUR_ACTION FTSP-4-UNEXPECTEDEVENT 4-Warning Bad event received\n\[dec] [dec] An unexpected event was received. - LOG_STD_RECUR_ACTION FTSP-4-UNEXPECTEDEVENT 4-Warning Bad event received\n\[dec] [dec] An unexpected event was received. - LOG_STD_RECUR_ACTION FTSP-6-FAX_CONNECT 6-Information [chars] Fax carrier detected - LOG_STD_NO_ACTION FTSP-6-FAX_CONNECT 6-Information [chars] Fax carrier detected - LOG_STD_NO_ACTION FTSP-6-FAX_DISCONNECT 6-Information [chars] Fax call disconnected - LOG_STD_NO_ACTION FTSP-6-FAX_DISCONNECT 6-Information [chars] Fax call disconnected - LOG_STD_NO_ACTION FTTM-3-ERROR 3-Error [chars] Full Ternary TCAM Manager Error - LOG_STD_SH_TECH_ACTION FW_HA-3-CF_REG_FAILED 3-Error Firewall High availability registration to CF failed Firewall High Availability could not register as a Checkpoint Facility\n\ client ios-firewall "Firewall HA subsys registration as Checkpoint Facility client failed \n\ verify if this image is capable of doing Box-Box redundancy. \n\ Collect the image version information and report the probelm to\n\ Cisco Technical assistance centre" FW_HA-3-RF_REG_FAILED 3-Error Firewall High availability registration to RF failed Firewall High Availability could not register as a Redundancy Facility\n\ client ios-firewall "Firewall HA subsys registration as Redundancy Facility client failed \n\ verify if this image is capable of doing Box-Box redundancy. \n\ Collect the image version information and report the probelm to\n\ Cisco Technical assistance centre" FW_HA-3-SUBSYS_INIT_FAILED 3-Error Firewall High availability subsystem initialization failed Firewall High Availability subsystem initialization failed ios-firewall "Firewall HA subsystem initialization failed under unsual circumstances \n\ Check the available memory and CPU utilization on the router and verify \n\ that it satisfies the requirements for the feature \n\ If the requirement are satisfied collect the output of show tac and \n\ report it to Cisco Technical assistance centre." FW_HA-3-TW_INIT_FAILED 3-Error Firewall High availability update timer initialization failed Firewall High Availability update timer initialization failed ios-firewall "Firewall HA update timer initialization failed under unsual circumstances \n\ Check the available memory and CPU utilization on the router and verify \n\ that it satisfies the requirements for the feature \n\ If the requirement are satisfied collect the output of show tac and \n\ report it to Cisco Technical assistance centre." FW_HA-6-AUDIT_TRAIL_STDBY_START 6-Information [chars]Start [chars] standby session: initiator [inet]:[dec] -- responder [inet]:[dec] This message documents the opening of an inspection session on \n\ standby router. The message is issued at the start of each\n\ inspected session and it records the source/destination\n\ addresses and ports. ios-firewall "This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions." FW_HA-6-AUDIT_TRAIL_STDBY_STOP 6-Information [chars]Stop [chars] standby session: initiator [inet]:[dec] -- responder [inet]:[dec] This message documents the deletion of an inspection session on\n\ standby router. The message is issued at the end of each\n\ inspected session and it records the source/destination\n\ addresses and ports. ios-firewall "This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions." FW_HA-6-AUDIT_TRAIL_STDBY_TO_ACT 6-Information Sessions matching HSRP group [chars] are being transitioned from Standby to Active state This message documents sessions on standby router that\n\ match this hsrp group name are changed to active. The message\n\ is issued when the standby router becomes active ios-firewall "This message is for informational purposed only and can be used\n\ to collect the basic accounting for inspected sessions." FW_HA-6-NO_HSRP_GNAME_ON_STDBY 6-Information Firewall High availability - Inpsect redundancy group is not configured on standby for interface [chars] dir in/out NO hsrp group name on standby is configured on same interface and\n\ inspect dir configured on active ios-firewall "Please check firewall configuration on standby and make sure it \n\ is same with active's configuration" FW_HA-6-NO_INSPECT_RULE_ON_STDBY 6-Information Firewall High availability - inspect rule is not configured on standby for interface [chars] dir in/out NO inspect rule on standby is configured on same interface and inspect\n\ dir configured on active ios-firewall "Please check firewall configuration on standby and make sure it should \n\ be same with active's configuration" FW_HA-6-PROT_MISMATCH 6-Information Firewall High availability - L4/L7 protocol mismatch between active and standby Firewall High Availability configuration of inspect rule or hsrp group \n\ name does not match between the Active and Standby devices ios-firewall "Firewall High Availability configuration between the Active and Standby\n\ devices are not automatically synched. Check to see if the configuration\n\ of the Active and Standby are in synch. Check the configuration guidelines\n\ for all areas that should match." FW-2-BLOCK_HOST 2-Critical [chars]Blocking new TCP connections to host [inet] for [dec] minute[chars] half-open count [dec] exceeded. This message indicates that any subsequent new TCP connection \n\ attempts to the specified host will be denied because the \n\ max-incomplete host threshold of half-open TCP connections is \n\ exceeded and the blocking option is configured to block the \n\ subsequent new connections. The blocking will be removed when the \n\ configured block-time expires. firewall "This message is for informational purposes only but may indicate \n\ that a SYN flood attack was attempted." FW-2-BLOCK_HOST 2-Critical target:class-[chars]:[chars]:Blocking new TCP connections to host [inet] for [dec] minute[chars] half-open count [dec] exceeded. [chars] This message indicates that any subsequent new TCP connection \n attempts to the specified host will be denied because the \n max-incomplete host threshold of half-open TCP connections is \n exceeded and the blocking option is configured to block the \n subsequent new connections. The blocking will be removed when the \n configured block-time expires. cpp-ucode "This message is for informational purposes only but may indicate \n"" that a SYN flood attack was attempted." FW-3-FTP_NON_MATCHING_IP_ADDR 3-Error [chars]Non-matching address [inet] used in [chars] -- FTP client [inet] FTP server [inet] An FTP client attempted to use a PORT command or the FTP server \n\ attempted to use the response to a PASV command to trick the \n\ firewall into opening access to a third-party host that is \n\ different from the two hosts engaged in the FTP connection. \n\ This message indicates that a suspicious violation was detected \n\ while attempting to modify the security policy in the firewall. \n\ The command is rejected and the connection is reset by the \n\ firewall. firewall "This message is for informational purposes only but may indicate \n\ that an attempt was made to grant or open access to unauthorized \n\ hosts." FW-3-FTP_PRIV_PORT 3-Error [chars]Privileged port [dec] used in [chars] -- FTP client [inet] FTP server [inet] An FTP client attempted to use a PORT command or the FTP server \n\ attempted to use the response to a PASV command to trick the \n\ firewall into opening access to a privileged port. This message \n\ indicates that a suspicious violation was detected from the FTP \n\ client/server attempting to modify the security policy in the \n\ firewall. The command is rejected and the connection is reset by \n\ the firewall. firewall "This message is for informational purposes only but may indicate that an attempt was made to gain access to privileged ports." FW-3-FTP_SESSION_NOT_AUTHENTICATED 3-Error [chars]Command issued before the session is authenticated -- FTP client [inet] FTP server [inet] An FTP client attempted to use the PORT command or an FTP server \n\ attempted to use the response to a PASV command to open a data \n\ channel in the firewall prior to the client's successful \n\ authentication with the server. This is a suspicious attempt by \n\ the client/server to trick the firewall into opening a hole \n\ so that outside attackers can take advantage of the firewall \n\ opening. This message indicates that a suspicious violation was \n\ detected and the PORT or PASV command/response is rejected \n\ by the firewall. The data channel in the firewall will not be \n\ opened until the authentication is done successfully. firewall "This message is for informational purposes only but may indicate \n\ that an illegal attempt was made to modify the firewall security \n\ policy." FW-3-HTTP_JAVA_BLOCK 3-Error [chars]JAVA applet is blocked from [inet]:[dec] to [inet]:[dec]. A Java applet was seen in the HTTP channel and the firewall \n\ configuration indicates that the applet from this Web site should \n\ be prohibited. The message indicates that the applet is being \n\ downloaded from one of the prohibited sites and its entrance to \n\ the protected network is not allowed. The connection is reset and \n\ the transmission of the detected applet is aborted immediately. firewall "This message is for informational purposes only but may indicate a security problem." FW-3-INTERNAL_ERROR 3-Error IP Firewall internal failure -- [chars] This message indicates the misc errors in the IP FW subsystem firewall "This message indicates the misc errors in the IP FW subsystem" FW-3-NOTFOUND 3-Error [chars]Session context for [inet]:[dec] => [inet]:[dec] not found. The CBAC code was searching its database for information for a \n\ particular inspection session but this information was not found. firewall "If this message recurs copy it down exactly as it appears and \n\ contact your technical support representative for assistance." FW-3-RESPONDER_WND_SCALE_INI_NO_SCALE 3-Error Dropping packet - Invalid Window Scale option for session [inet]:[dec] to [inet]:[dec] Initiator scale [dec] Responder scale [dec] Firewall detected the packet from Responder to Initiator \n\ has windows scaling option but did not have the scaling \n\ option in the SYN packet from Initiator to responder. \n\ This is an error according to RFC 1323 firewall "Turn on window scaling option on both Initiator" " and Responderor Turn off window scaling on the" " Responder" FW-3-SMTP_INVALID_COMMAND 3-Error [chars]Invalid SMTP command [chars]total [dec] chars from initiator [inet]:[dec] The CBAC code detected an invalid SMTP command in the inspected \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system. \n\ The command is rejected and the connection is reset by the firewall \n\ immediately. firewall "This message is for informational purposes only but may indicate\n\ a security problem." FW-3-TIMER_WHEEL_INIT_FAILED 3-Error Timer Wheel initialization failed This message indicates that Timer Wheel initialization is\n\ failed in the FW subsystem - "This message indicates a series problem with IOS Firewall. \n\ On seeing this error message copy the message exactly as \n\ it appears and report it to your technical support \n\ representative." FW-4-AGG_AGE_PERIOD_OFF 4-Warning [chars] session count has dipped below the aggressive aging low watermark [dec] [chars] The number of per-box half-open or total sessions has gone \n below the aggressive aging low threshold. This message indicates \n end of aggressive aging period. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-AGG_AGE_PERIOD_ON 4-Warning [chars] session count has exceeded the aggressive aging high watermark [dec] [chars] Start aggressive aging period. The aggressive aging high threshold \n of per-box halfopen or total sessions has been exceeded. \n This message indicates that a DOS attack may be in progress hence \n aggressive aging feature will take affect. The feature protects \n the firewall sessions resources by allowing idle sessions to be \n exist for a shorter period of time. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-ALERT_OFF 4-Warning [chars][chars] count [dec]/[dec] current 1-min rate: [dec] Either the number of half-open connections or the new connection \n\ initiation rate has gone below the max-incomplete low threshold. \n\ This message indicates that the rate of incoming new connections \n\ has slowed down and is issued only when the max-incomplete low \n\ threshold is crossed. firewall "This message is for informational purposed only but may indicate \n\ that an attack has stopped." FW-4-ALERT_OFF 4-Warning target:class-[chars]:[chars]:[chars] count [dec]/[dec] current rate: [dec] [chars] Either the number of half-open connections or the new connection \n initiation rate has gone below the max-incomplete low threshold. \n This message indicates that the rate of incoming new connections \n has slowed down and is issued only when the max-incomplete low \n threshold is crossed. cpp-ucode "This message is for informational purposed only but may indicate \n"" that an attack has stopped." FW-4-ALERT_ON 4-Warning [chars][chars] count [dec]/[dec] current 1-min rate: [dec] Either the max-incomplete high threshold of half-open connections \n\ or the new connection initiation rate has been exceeded. This error \n\ message indicates that an unusually high rate of new connections is \n\ coming through the firewall and a DOS attack may be in progress. \n\ This message is issued only when the max-incomplete high threshold \n\ is crossed. firewall "This message is for informational purposed only but may indicate \n\ a security problem." FW-4-ALERT_ON 4-Warning target:class-[chars]:[chars]:[chars] count [dec]/[dec] current rate: [dec] [chars] Either the max-incomplete high threshold of half-open connections \n or the new connection initiation rate has been exceeded. This error \n message indicates that an unusually high rate of new connections is \n coming through the firewall and a DOS attack may be in progress. \n This message is issued only when the max-incomplete high threshold \n is crossed. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-HALFOPEN_LIMIT_EXCEEDED 4-Warning [chars] half open session limit exceeded. configured limit [dec] The halfopen session limit of a specific layer 4 protocol or the total \n halfopen session limit exceeded. \n This error message indicates that an unusually high rate of new \n connections is coming through the firewall and a DOS attack may be in \n progress. \n This message is issued only when the max-incomplete high threshold \n is crossed. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-HOST_TCP_ALERT_ON 4-Warning [chars]Max tcp half-open connections [dec] exceeded for host [inet]. The max-incomplete host limit of half-open TCP connections has been \n\ exceeded. This message indicates that a high number of half-open \n\ connections is coming to the protected server and may indicate \n\ that a SYN flood attack is in progress and is targeted to the \n\ specified server host. firewall "This message is for informational purposes only but may indicate \n\ that a SYN flood attack was attempted. If this alert is issued \n\ frequently and identified to be mostly false alarms then the \n\ max-incomplete host threshold value is probably set too low \n\ and there is a lot of legitimate traffic coming in to that server. \n\ In this case the max-incomplete host parameter should be set to \n\ a higher number to avoid false alarms." FW-4-HOST_TCP_ALERT_ON 4-Warning target:class-[chars]:[chars]:Max tcp half-open connections [dec] exceeded for host [inet][chars]. [chars] - - - FW-4-SESSION_THRESHOLD_EXCEEDED 4-Warning [chars]Number of sessions for the firewall rule '[chars]' applied on interface '[chars]' exceeds the configured threshold [dec] This message indicates that the number of established CBAC\n\ sessions have crossed the configured threshold. firewall "This message is for informational purpose only but may indicate\n\ a security problem. This might also mean that the session threshold\n\ is set to a low value in which case the threshold value could be\n\ increased through CLI command" FW-4-SESSIONS_MAXIMUM 4-Warning Number of sessions for the firewall policy on target:class-[chars]:[chars] exceeds This message indicates that the number of established ZBF\n sessions have crossed the configured sessions maximum limit cpp-ucode "This message is for informational purpose only but may indicate\n"" a security problem. This might also mean that the sessions maximum \n"" is set to a low value in which case the sessions maximum value could be\n"" increased through paramter-map type inspect CLI" FW-4-TCP_MAJORDOMO_EXEC_BUG 4-Warning [chars]Majordomo Execute Attack - from [inet] to [inet] A bug in the Majordomo program will allow remote users to\n\ execute arbitrary commands at the privilege level of the\n\ server. firewall "For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately." FW-4-TCP_SENDMAIL_BAD_FROM_SIG 4-Warning [chars]Sendmail Invalid Sender - from [inet] to [inet] - firewall "For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately." FW-4-TCP_SENDMAIL_BAD_TO_SIG 4-Warning [chars]Sendmail Invalid Recipient - from [inet] to [inet] - firewall "For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately." FW-4-TCP_SENDMAIL_DECODE 4-Warning [chars]Sendmail Decode Alias - from [inet] to [inet] Triggers on any mail message with '': decode@'' in the header.\n\ The decode alias is used to uudecode files and is primarily\n\ implemented as a convenience for system administration. firewall "For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately." FW-4-TCP_SENDMAIL_INVALID_COMMAND 4-Warning [chars]Invalid SMTP command - [inet] to [inet] Triggers on an invalid SMTP command in the \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system. firewall "This is unusual traffic and may warrant\n\investigation." FW-4-TCP_SENDMAIL_OLD_SIG 4-Warning [chars]Archaic Sendmail Attacks - from [inet] to [inet] Triggers when ''wiz'' or ''debug'' commands are sent to the SMTP port. firewall "For security reasons users should not \n\be allowed to execute programs via e-mail servers. This is a very \n\serious indication that your network may be under attack and the \n\source should be shunned immediately." FW-4-UNBLOCK_HOST 4-Warning [chars]New TCP connections to host [inet] no longer blocked New TCP connection attempts to the specified host are no longer \n\ blocked. This message indicates that the blocking of new TCP \n\ attempts to the specified host has been lifted. firewall "This message is for informational purposed only but may indicate \n\ a SYN flood attack was attempted to the host." FW-4-UNBLOCK_HOST 4-Warning target:class-[chars]:[chars]:New TCP connections to host [inet][chars] no longer blocked [chars] New TCP connection attempts to the specified host are no longer \n blocked. This message indicates that the blocking of new TCP \n attempts to the specified host has been lifted. cpp-ucode "This message is for informational purposed only but may indicate \n"" a SYN flood attack was attempted to the host." FW-4-VRF_AGG_AGE_PERIOD_OFF 4-Warning [chars] session count of VRF id [dec] has dipped below the aggressive aging low watermark [dec] [chars] The number of VRF half-open or total sessions has gone \n below the aggressive aging low threshold. This message indicates \n end of aggressive aging period. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-VRF_AGG_AGE_PERIOD_ON 4-Warning [chars] session count of VRF id [dec] has exceeded the aggressive aging high watermark [dec] [chars] Start aggressive aging period for VRF. The aggressive aging high \n threshold of VRF halfopen or total sessions has been exceeded. \n This message indicates that a DOS attack may be in progress hence \n aggressive aging feature will take affect. The feature protects \n the firewall sessions resources by allowing idle sessions to be \n exist for a shorter period of time. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-4-VRF_HALFOPEN_LIMIT_EXCEEDED 4-Warning VRF id [dec] [chars] half open session limit exceeded. configured limit [dec] [chars] The halfopen session limit of a specific layer 4 protocol or the total \n halfopen session limit exceeded for a specific vrf id. \n This error message indicates that an unusually high rate of new \n connections is coming through the firewall and a DOS attack may be in \n progress. \n This message is issued only when the max-incomplete high threshold \n is crossed. cpp-ucode "This message is for informational purposed only but may indicate \n"" a security problem." FW-5-EMAIL_DROP_FRAGMENT 5-Notice [chars]Dropping [chars] command fragment from initiator [inet]:[dec] - - - FW-5-IMAP_INVALID_COMMAND 5-Notice [chars]Invalid IMAP command from initiator [inet]:[dec]: [chars] - - - FW-5-IMAP_NON_SECURE_LOGIN 5-Notice [chars]LOGON IMAP command from initiator [inet]:[dec]: [chars] The CBAC code detected a cleartext logon attempt in the inspected IMAP\n\ connection while secure-login is configured.\n\ The command is rejected and the connection is reset by the firewall\n\ immediately. firewall "This message is for informational purposes only but may indicate a\n\ security problem." FW-5-POP3_INVALID_COMMAND 5-Notice [chars]Invalid POP3 command from initiator [inet]:[dec]: [chars] - - - FW-5-POP3_NON_SECURE_LOGIN 5-Notice [chars]LOGON POP3 command from initiator [inet]:[dec]: [chars] The CBAC code detected a cleartext logon attempt in the inspected POP3\n\ connection while secure-login is configured.\n\ The command is rejected and the connection is reset by the firewall\n\ immediately. firewall "This message is for informational purposes only but may indicate a\n\ security problem." FW-6-DROP_PKT 6-Information Dropping [chars] pkt [inet]:[dec] => [inet]:[dec] Packet dropped by firewall inspection. firewall "This message is for informational purposes only. \n\ It may be used to verify that packets were dropped by the firewall." FW-6-DROP_PKT 6-Information Dropping [chars][chars] pkt from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars] with ip ident [dec] [chars] [chars] [chars] [chars] [chars] - - - FW-6-LOG_SUMMARY 6-Information [dec] [chars] packet[chars] [chars] from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars] - - - FW-6-PASS_PKT 6-Information Passing [chars] pkt from [chars] [inet][chars]:[dec] => [inet][chars]:[dec] target:class-[chars]:[chars] [chars] [chars] with ip ident [dec] [chars] - - - FW-6-PRE_ALLOCATED_MEDIA_CHANNEL 6-Information [chars]Pre-Allocated [chars] channel from [inet][[dec]:[dec]] to [inet][[dec]:[dec]] Firewall inspection is configured on at least one interface in the\n\ startup config. firewall "This message is for informational purposes only. \n\ It may be used to verify whether firewall inspection is on at startup." FW-6-SESS_AUDIT_TRAIL 6-Information [chars]Stop [chars] session: initiator [inet]:[dec] sent [dec] bytes -- responder [inet]:[dec] sent [dec] bytes This message documents the per-session transaction log of network \n\ activities. The message is issued at the end of each inspected \n\ session and it records the source/destination addresses and ports \n\ as well as the number of bytes transmitted by the client and \n\ server. firewall "This message is for informational purposed only and can be used \n\ to collect the basic accounting for the inspected sessions." FW-6-SESS_AUDIT_TRAIL 6-Information target:class-[chars]:[chars]:Stop [chars] session: initiator [inet][chars]:[dec] This message documents the per-session transaction log of network \n activities. The message is issued at the end of each inspected \n session and it records the source/destination addresses and ports \n as well as the number of bytes transmitted by the client and \n server. cpp-ucode "This message is for informational purposed only and can be used \n"" to collect the basic accounting for the inspected sessions." FW-6-SESS_AUDIT_TRAIL_START 6-Information [chars]Start [chars] session: initiator [inet]:[dec] -- responder [inet]:[dec] This message documents the opening of an inspection session.\n\ The message is issued at the start of each inspected session\n\ and it records the source/destination addresses and ports. firewall "This message is for informational purposed only and can be used \n\ to collect the basic accounting for inspected sessions." FW-6-SESS_AUDIT_TRAIL_START 6-Information target:class-[chars]:[chars]:Start [chars] session: initiator [inet][chars]:[dec] This message documents the opening of an inspection session.\n The message is issued at the start of each inspected session\n and it records the source/destination addresses and ports. cpp-ucode "This message is for informational purposed only and can be used \n"" to collect the basic accounting for inspected sessions." FWALL_PROXY-3-PROXY_DEBUG_REG_FAILED 3-Error [dec] FW Conditional Debugging registration failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_FWALL_DOUBLE_INIT 3-Error Data plane double initialization request. Coding error - second attempt to initialize data plane. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_FWALL_FBD_NOT_ENABLED 3-Error FBD Not enabled.. cannot initialize data plane. Mismatch in FBD capabiities between client and data plane. Coding error. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_FWALL_INIT_FAILED 3-Error [dec] Firewall initialization failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_FWALL_VFR_REG_FAILED 3-Error [chars] err: [dec] FW VFR registration failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HA_MEM_EXTEND_FAILED 3-Error - Increasing of ha retry pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HA_MEM_INIT_FAILED 3-Error - Initialization of ha retry pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HOSTDB_MEM_EXTEND_FAILED 3-Error - Increasing of host database pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HOSTDB_MEM_INIT_FAILED 3-Error - Initialization of host database pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_ADD_DEST_FAILED 3-Error - HSL add destination failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_BIND_FAILED 3-Error - HSL bind failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_BIND_TEMPLATE_FAILED 3-Error [dec] HSL bind tempalte failed at given index. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_CREATE_FAILED 3-Error - HSL creation failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_ENABLE_FAILED 3-Error - HSL enable failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_MODIFY_DEST_FAILED 3-Error - HSL modify destination failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_HSL_MODIFY_FAILED 3-Error - HSL modification failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_ICMP_ERROR_MEM_EXTEND_FAILED 3-Error - Increasing of ICMP Error pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_ICMP_ERROR_MEM_INIT_FAILED 3-Error - Initialization of ICMP Error control block pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error [dec] IPC allocation failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_ERM_CONF_CHANGE_FAILED 3-Error [dec] FW IPC send failed to reply for event rate monitoring configuration change. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_FAILED 3-Error [chars] [dec] IPC message allocation for firewall failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_CLEAR_FAILED 3-Error [dec] IPC send failed to reply for firewall session clear. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_DEBUG_FAILED 3-Error [dec] IPC send failed to reply for firewall session debug. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error [dec]:[chars] IPC send failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_INIT_FAILED 3-Error [chars] [dec] IPC failed to reply for firewall initialization status. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_SCB_QUERY_FAILED 3-Error [dec] IPC send failed to reply for firewall scb query. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_SESSION_FAILED 3-Error [dec] IPC send failed to reply for firewall session query. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_IPC_SEND_STATS_FAILED 3-Error [dec] IPC send failed to reply for firewall status. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_SCB_MEM_EXTEND_FAILED 3-Error - Increasing of session control block pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_SCB_MEM_INIT_FAILED 3-Error - Initialization of session control block pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_TBL_INIT_FAILED 3-Error [chars] Failed to initialize table. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_TEARDOWN_MEM_EXTEND_FAILED 3-Error - Increasing of teardown pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-3-PROXY_TEARDOWN_MEM_INIT_FAILED 3-Error - Initialization of teardown pool failed. cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_HSL_ALREADY_INIT 4-Warning - HSL logger already initialized cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_HSL_NOT_INIT 4-Warning [dec] HSL logger not initialized cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Invalid IPC message subtype. cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_IPC_INVALID_MSG_LEN 4-Warning [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length. cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_IPC_UNINIT_POOL_FAILED 4-Warning [chars]: [dec] Could not destroy chunk pool cpp-ucode LOG_STD_ACTION FWALL_PROXY-4-PROXY_UNINIT_SESSIONS 4-Warning in use [dec] [dec] Not all sessions freed cpp-ucode LOG_STD_ACTION FWALL-3-FW_ALG_INVALID_TYPE 3-Error [chars] [dec]:[dec] Invalid alg type passed from alg to firewall cpp-ucode LOG_STD_ACTION FWALL-3-FW_NO_MATCH_INDEX_STATS 3-Error [dec]---[dec] Client has not provided stats for the given match_index cpp-ucode LOG_STD_ACTION FWALL-3-FW_NO_STATS 3-Error [dec]:[dec] zone pair [chars] class [chars] Client has not provided stats for the given protocol:applicaton id cpp-ucode LOG_STD_ACTION FWALL-3-HA_INVALID_MSG_RCVD 3-Error invalid [chars] [hec] expected [hec] opcode [chars] [hec] Standby received an invalid Firewall HA message cpp-ucode LOG_STD_ACTION FWALL-3-HA_INVALID_STATE 3-Error [dec] Invalid state cpp-ucode LOG_STD_ACTION FWALL-7-FW_NO_ALERT_CAUSE 7-Debug [dec] Unsupported alert cause cpp-ucode LOG_STD_ACTION FWALL-7-FW_NO_DROP_CAUSE 7-Debug [dec] Unsupported drop cause cpp-ucode LOG_STD_ACTION GBIC_SECURITY_CRYPT-4-ID_MISMATCH 4-Warning Identification check failed for GBIC in port [dec] The GBIC was identified as a Cisco GBIC but the system was unable to verify its identity firmware "Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required. Otherwise verify that the GBIC was obatined from Cisco or " "from a supported vendor." GBIC_SECURITY_CRYPT-4-UNRECOGNIZED_VENDOR 4-Warning GBIC in port [dec] manufactured by an unrecognized vendor The GBIC was identified as a Cisco GBIC but the system was unable to match its manufacturer with one on the known list of Cisco GBIC vendors firmware "Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required." GBIC_SECURITY_CRYPT-4-VN_DATA_CRC_ERROR 4-Warning GBIC in port [dec] has bad crc The GBIC was identified as a Cisco GBIC but it does not have valid CRC in the EEPROM data. firmware "Check to see if the Cisco IOS software running on the system supports " "the GBIC. If the GBIC is newer a system software upgrade might be " "required. Even if the GBIC is unrecognized by the system the GBIC " "may still operate properly but might have limited functionality." GBIC_SECURITY_UNIQUE-3-DUPLICATE_GBIC 3-Error GBIC interface [dec]/[dec] is a duplicate of GBIC interface [dec]/[dec] The GBIC was identified as a Cisco GBIC but its vendor ID and serial number match that of another interface on the system. firmware "Cisco GBICs are assigned unique serial numbers. Verify that the GBIC " "was obtained from Cisco or a supported vendor" GBIC_SECURITY_UNIQUE-4-DUPLICATE_SN 4-Warning GBIC interface [dec]/[dec] has the same serial number as another GBIC interface The GBIC was identified as a Cisco GBIC but its serial number matches that of another interface on the system. firmware "Cisco GBICs are assigned unique serial numbers. Verify that the GBIC " "was obtained from Cisco or a supported vendor" GBIC_SECURITY-4-EEPROM_CRC_ERR 4-Warning EEPROM checksum error for GBIC in [chars] The GBIC in the port specified in the error message has invalid EEPROM data. - "Remove the GBIC from the specified port." GBIC_SECURITY-4-EEPROM_READ_ERR 4-Warning Error in reading GBIC serial ID in [chars] Error when reading GBIC type from EEPROM - "Please remove GBIC from this Port" GBIC_SECURITY-4-EEPROM_SECURITY_ERR 4-Warning GBIC in [chars] failed security check The GBIC in the port specified in the error message has invalid EEPROM data. - "Remove the GBIC from the specified port." GBIC_SECURITY-4-GBIC_INTERR 4-Warning Internal error occurred in setup for GBIC interface [chars] The system could not allocate resources or had some other problem in the setup for the specified GBIC interface. firmware "Reload the system. If the problem persists " "contact TAC." GBIC-4-CHECK_SUM_FAILED 4-Warning GBIC EEPROM data check sum failed for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read vendor-data information to verify its correctness. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-CHECK_SUM_FAILED 4-Warning GBIC EEPROM data check sum failed for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read vendor-data information to verify its correctness. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VNAME 4-Warning Unable to read vendor name for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read the name of the GBIC's vendor. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VNAME 4-Warning Unable to read vendor name for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read the name of the GBIC's vendor. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VSDATA 4-Warning Unable to read vendor-specific data for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read identifying vendor-specific information to verify its authenticity. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VSDATA 4-Warning Unable to read vendor-specific data for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read identifying vendor-specific information to verify its authenticity. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VSERNUM 4-Warning Unable to read serial number for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read the GBIC's serial number. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-NOREAD_VSERNUM 4-Warning Unable to read serial number for GBIC interface [chars] The GBIC was identified as a Cisco GBIC but the system was unable to read the GBIC's serial number. firmware "Remove and reinsert the GBIC. If it fails " "again in the same way the GBIC may be defective." GBIC-4-UNRECOGNIZED_EXTTYPE 4-Warning GBIC interface [chars] has unrecognized extended type The GBIC was identified as a Cisco GBIC but the system does not recognize its reported extended type code. firmware "Check the list of supported GBICs for this version " "of the system software. An upgrade may be required " "for newer GBICs. Even if unrecognized the GBIC " "may still operate properly perhaps with limited " "functionality." GBIC-4-UNRECOGNIZED_EXTTYPE 4-Warning GBIC interface [chars] has unrecognized extended type The GBIC was identified as a Cisco GBIC but the system does not recognize its reported extended type code. firmware "Check the list of supported GBICs for this version " "of the system software. An upgrade may be required " "for newer GBICs. Even if unrecognized the GBIC " "may still operate properly perhaps with limited " "functionality." GBIC-4-XCVR_INTERR 4-Warning Internal error occurred in setup for GBIC interface [chars] The system could not allocate resources or had some other problem in the setup for the specified GBIC interface. firmware "Reload the system. If the problem persists " "contact TAC." GBIC-4-XCVR_INTERR 4-Warning Internal error occurred in setup for GBIC interface [chars] The system could not allocate resources or had some other problem in the setup for the specified GBIC interface. firmware "Reload the system. If the problem persists " "contact TAC." GBIC-6-SERDES_MODULE_UNKNOWN 6-Information Unrecognizable GBIC found in [chars] module mask 0x%02x The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC. firmware "If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch." GBIC-6-SERDES_MODULE_UNKNOWN 6-Information Unrecognizable GBIC found in [chars] module mask 0x%02x The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC. firmware "If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch." GBIC-6-SERDES_SERIAL_INV_DATA 6-Information Unrecognizable GBIC found in [chars] serial data 0x%02x The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC. firmware "If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch." GBIC-6-SERDES_SERIAL_INV_DATA 6-Information Unrecognizable GBIC found in [chars] serial data 0x%02x The GBIC presented data to the system which did not correctly identify the type of the GBIC. It will be handled as a 'generic' GBIC. firmware "If the GBIC fails to become operational " "carefully reinsert it in the slot. If it " "continues to fail after reinsertion " "the GBIC may be defective or incompatible " "with the switch." GDOI-1-GDOI_ACE_DENY 1-Alert A Group Member ACL policy containing deny was attempted. This is not supported. A Group Member ACL policy containing deny was attempted. This is not supported. ipsec-getvpn LOG_STD_ACTION GDOI-1-GDOI_ACE_DENY 1-Alert A Group Member ACL policy containing deny was attempted. This is not supported. A Group Member ACL policy containing deny was attempted. This is not supported. ipsec-getvpn LOG_STD_ACTION GDOI-1-GDOI_ACL_NUM 1-Alert The ACL has too many entries.\n GDOI will honor only the first 100 ACL entries specified. The ACL has too many entries. GDOI will honor only the first 100 ACL entries specified. ipsec-getvpn LOG_STD_ACTION GDOI-1-GDOI_ACL_NUM 1-Alert The ACL has too many entries.\n GDOI will honor only the first 100 ACL entries specified. The ACL has too many entries. GDOI will honor only the first 100 ACL entries specified. ipsec-getvpn LOG_STD_ACTION GDOI-1-KS_NO_RSA_KEYS 1-Alert RSA Key - [chars] : Not found Required for group [chars] Rsa Keys were not found in Key Server and they are required for signing and verifying rekey messages ipsec-getvpn "Contact the Key Server's administrator and ask him to do create" " the RSA Key pair" GDOI-1-KS_NO_RSA_KEYS 1-Alert RSA Key - [chars] : Not found Required for group [chars] Rsa Keys were not found in Key Server and they are required for signing and verifying rekey messages ipsec-getvpn "Contact the Key Server's administrator and ask him to do create" " the RSA Key pair" GDOI-1-UNAUTHORIZED_IDENTITY 1-Alert Group [chars] received registration from unauthorized identity: [chars] The registration request was dropped because the requesting device was not authorized to join the group. ipsec-getvpn LOG_STD_ACTION GDOI-1-UNAUTHORIZED_IDENTITY 1-Alert Group [chars] received registration from unauthorized identity: [chars] The registration request was dropped because the requesting device was not authorized to join the group. ipsec-getvpn LOG_STD_ACTION GDOI-1-UNAUTHORIZED_IPADDR 1-Alert Group [chars] received registration from unauthorized ip address: [chars] The registration request was dropped because the requesting device was not authorized to join the group. ipsec-getvpn LOG_STD_ACTION GDOI-1-UNAUTHORIZED_IPADDR 1-Alert Group [chars] received registration from unauthorized ip address: [chars] The registration request was dropped because the requesting device was not authorized to join the group. ipsec-getvpn LOG_STD_ACTION GDOI-1-UNREGISTERED_INTERFACE 1-Alert Group [chars] received registration from unregistered interface. Receiving registration from unregistered interface. Stop processing it. ipsec-getvpn LOG_STD_ACTION GDOI-1-UNREGISTERED_INTERFACE 1-Alert Group [chars] received registration from unregistered interface. Receiving registration from unregistered interface. Stop processing it. ipsec-getvpn LOG_STD_ACTION GDOI-2-COOP_MINOR_VERSION_MISMATCH 2-Critical COOP-KS Minor version mistmatch in group [chars]. My COOP version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]. Upgrade [chars] [chars] to COOP version [dec].[dec].[dec] to prevent COOP outage. Coop KS has different minor version. ipsec-getvpn "show crypto gdoi ks coop" GDOI-2-COOP_MINOR_VERSION_MISMATCH 2-Critical COOP-KS Minor version mistmatch in group [chars]. My COOP version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec]. Upgrade [chars] [chars] to COOP version [dec].[dec].[dec] to prevent COOP outage. Coop KS has different minor version. ipsec-getvpn "show crypto gdoi ks coop" GDOI-3-COOP_ANN_SEQ_FAILURE 3-Error COOP Ann msg seq check failed for group [chars] ann seq# [dec] sess seq# [dec] COOP Ann msg seq check failed ipsec-getvpn "Contact Administrator" GDOI-3-COOP_ANN_SEQ_FAILURE 3-Error COOP Ann msg seq check failed for group [chars] ann seq# [dec] sess seq# [dec] COOP Ann msg seq check failed ipsec-getvpn "Contact Administrator" GDOI-3-COOP_CONFIG_MISMATCH 3-Error WARNING: Group [chars] [chars] configuration between Primary KS and Secondary KS are mismatched The configuration between Primary KS and Secondary KS are mismatched ipsec-getvpn "Contact the Key Sever's administrator" GDOI-3-COOP_CONFIG_MISMATCH 3-Error WARNING: Group [chars] [chars] configuration between Primary KS and Secondary KS are mismatched The configuration between Primary KS and Secondary KS are mismatched ipsec-getvpn "Contact the Key Sever's administrator" GDOI-3-COOP_KS_CANNOT_FIND_PROFILE 3-Error Coop KS in group [chars] has a configured IKEv2 profile '[chars]' that doesn't exist. The COOP will not come up until this error is fixed. The KS COOP coniguration redunadancy ikve2-profile specifies a profile that doesn't exist. The COOP will not come up. ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_CANNOT_FIND_PROFILE 3-Error Coop KS in group [chars] has a configured IKEv2 profile '[chars]' that doesn't exist. The COOP will not come up until this error is fixed. The KS COOP coniguration redunadancy ikve2-profile specifies a profile that doesn't exist. The COOP will not come up. ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_SEND_WINDOW_LIMIT_REACHED 3-Error The COOP KS has reached its window limit for the peer addresses local [chars] remote [chars]. This is due to connectivity issues between the key servers in question. The COOP KS running over IKEv2 has a limit to the number of pending messages that can be sent. This limit has been reached which is an indication that there is a connectivity issue between the key servers ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_SEND_WINDOW_LIMIT_REACHED 3-Error The COOP KS has reached its window limit for the peer addresses local [chars] remote [chars]. This is due to connectivity issues between the key servers in question. The COOP KS running over IKEv2 has a limit to the number of pending messages that can be sent. This limit has been reached which is an indication that there is a connectivity issue between the key servers ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_TOO_MANY_GROUPS_SHARE_IKE_SA 3-Error The COOP KS has too many groups sharing the same IKE SA for the peer addresses local [chars] remote [chars]. Connectivity could be compromised. Please reduce to [dec]. There is a limit to the number of COOP KS groups that can share the. same IKE SA. This can lead to intermittent connectivity for the COOP KS in congested networks ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_TOO_MANY_GROUPS_SHARE_IKE_SA 3-Error The COOP KS has too many groups sharing the same IKE SA for the peer addresses local [chars] remote [chars]. Connectivity could be compromised. Please reduce to [dec]. There is a limit to the number of COOP KS groups that can share the. same IKE SA. This can lead to intermittent connectivity for the COOP KS in congested networks ipsec-getvpn LOG_STD_ACTION GDOI-3-COOP_KS_UNREACH 3-Error Cooperative KS [chars] Unreachable in group [chars]. IKE SA Status = [chars] The reachability between the configugred cooperative key servers is lost. Some might consider this a hostile event. ipsec-getvpn "Contach the Administrators of the configured key servers." GDOI-3-COOP_KS_UNREACH 3-Error Cooperative KS [chars] Unreachable in group [chars]. IKE SA Status = [chars] The reachability between the configugred cooperative key servers is lost. Some might consider this a hostile event. ipsec-getvpn "Contach the Administrators of the configured key servers." GDOI-3-COOP_KSSID_OVERLAP 3-Error Overlapping KS Sender Identifiers KSSID {[chars]} Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed. ipsec-getvpn "Check the configured KSSIDs for all COOP-KS peers by issuing " GDOI-3-COOP_KSSID_OVERLAP 3-Error Overlapping KS Sender Identifiers KSSID {[chars]} Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed. ipsec-getvpn "Check the configured KSSIDs for all COOP-KS peers by issuing " GDOI-3-COOP_LIMIT_REACHED 3-Error Peer [chars] has reached COOP limit of maximum number of gms. COOP GM database sync fails. Upgrade to COOP version [dec].[dec].[dec] and above COOP-KS has a non-compatible peer. ipsec-getvpn "Check COOP version compatibility on peer KS" GDOI-3-COOP_LIMIT_REACHED 3-Error Peer [chars] has reached COOP limit of maximum number of gms. COOP GM database sync fails. Upgrade to COOP version [dec].[dec].[dec] and above COOP-KS has a non-compatible peer. ipsec-getvpn "Check COOP version compatibility on peer KS" GDOI-3-COOP_MAJOR_VERSION_MISMATCH 3-Error COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] COOP-KS has a non-compatible major version. ipsec-getvpn "Check COOP version compatibility on KS" GDOI-3-COOP_MAJOR_VERSION_MISMATCH 3-Error COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] COOP-KS has a non-compatible major version. ipsec-getvpn "Check COOP version compatibility on KS" GDOI-3-COOP_PACKET_DROPPED 3-Error Announcement message dropped due to packet size [dec] bytes. Hard limit set on the driver buffer size prevents sending packets of this size or bigger ipsec-getvpn "Informational message" GDOI-3-COOP_PACKET_DROPPED 3-Error Announcement message dropped due to packet size [dec] bytes. Hard limit set on the driver buffer size prevents sending packets of this size or bigger ipsec-getvpn "Informational message" GDOI-3-GDOI_ACL_RANGE 3-Error The ACL [chars] contains port range which is NOT supported. WARNING: No TEK policy will be created. GDOI does not support port range in the ACL policy. ipsec-getvpn LOG_STD_ACTION GDOI-3-GDOI_ACL_RANGE 3-Error The ACL [chars] contains port range which is NOT supported. WARNING: No TEK policy will be created. GDOI does not support port range in the ACL policy. ipsec-getvpn LOG_STD_ACTION GDOI-3-GDOI_REKEY_FAILURE 3-Error Processing of REKEY payloads failed on GM [chars] in the group [chars] with peer at [chars] During GDOI rekey the payload parsing failed on this GM from the Key Server. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GDOI_REKEY_FAILURE 3-Error Processing of REKEY payloads failed on GM [chars] in the group [chars] with peer at [chars] During GDOI rekey the payload parsing failed on this GM from the Key Server. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GDOI_REKEY_SEQ_FAILURE 3-Error Failed to process rekey seq # [dec] in seq payload for group [chars] last seq # [dec] During GDOI rekey the seq payload parsing failed on this GM from the Key Server. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GDOI_REKEY_SEQ_FAILURE 3-Error Failed to process rekey seq # [dec] in seq payload for group [chars] last seq # [dec] During GDOI rekey the seq payload parsing failed on this GM from the Key Server. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GM_ACL_PERMIT 3-Error GM doesn't support permit configured under local access-list. Traffic from [chars] to [chars] will be dropped. GM can only support ACL for deny. Any traffic matching the permit entry will be dropped. ipsec-getvpn "Remove the permit entry from the ACL used by GDOI crypto map" GDOI-3-GM_ACL_PERMIT 3-Error GM doesn't support permit configured under local access-list. Traffic from [chars] to [chars] will be dropped. GM can only support ACL for deny. Any traffic matching the permit entry will be dropped. ipsec-getvpn "Remove the permit entry from the ACL used by GDOI crypto map" GDOI-3-GM_FAILED_TO_INITIALISE 3-Error GDOI GM Process has failed to initialise GDOI Group Member process has failed to initialise on this Network Element ipsec-getvpn - GDOI-3-GM_FAILED_TO_INITIALISE 3-Error GDOI GM Process has failed to initialise GDOI Group Member process has failed to initialise on this Network Element ipsec-getvpn - GDOI-3-GM_INCOMPLETE_CFG 3-Error Registration: incomplete config for group [chars] Registration can not be completed since the GDOI group configuration may be missing the group id server id or both ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GM_INCOMPLETE_CFG 3-Error Registration: incomplete config for group [chars] Registration can not be completed since the GDOI group configuration may be missing the group id server id or both ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GM_IPD3P_AND_CMD_CANT_COEXIST 3-Error GETVPN group-member does not support coexistance of IPD3P and Cisco-metadata features GETVPN group-member does not support the enabling of IPD3P and Cisco-metadata features e.g TBAR-PST SGT at the ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_IPD3P_AND_CMD_CANT_COEXIST 3-Error GETVPN group-member does not support coexistance of IPD3P and Cisco-metadata features GETVPN group-member does not support the enabling of IPD3P and Cisco-metadata features e.g TBAR-PST SGT at the ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_IPD3P_NO_IPV6_SUPPORT 3-Error GETVPN group-member does not support IP-D3P for IPv6. GETVPN group-member does not support IP-D3P for IPv6. ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_IPD3P_NO_IPV6_SUPPORT 3-Error GETVPN group-member does not support IP-D3P for IPv6. GETVPN group-member does not support IP-D3P for IPv6. ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_IPD3P_NO_TRANSPORT_SUPPORT 3-Error GETVPN group-member does not support IPD3P transport mode GETVPN group-member does not support IPD3P transport mode ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_IPD3P_NO_TRANSPORT_SUPPORT 3-Error GETVPN group-member does not support IPD3P transport mode GETVPN group-member does not support IPD3P transport mode ipsec-getvpn "Contact the Administrators to correct the key server policy." GDOI-3-GM_MAJOR_VERSION_MISMATCH 3-Error GM [inet] registration rejected due to major version mismatch. GM must be using major version [dec] in order to be compatible with this KS GM has a non-compatible major version. ipsec-getvpn "Check GDOI version compatibility on KS and GMs" GDOI-3-GM_MAJOR_VERSION_MISMATCH 3-Error GM [inet] registration rejected due to major version mismatch. GM must be using major version [dec] in order to be compatible with this KS GM has a non-compatible major version. ipsec-getvpn "Check GDOI version compatibility on KS and GMs" GDOI-3-GM_NO_CRYPTO_ENGINE 3-Error No crypto engine is found due to lack of resource or unsupported feature requested Failed to select a suitable crypto engine because requested packet path not available or requested feature not supported ipsec-getvpn "Check policy configured on KS" GDOI-3-GM_NO_CRYPTO_ENGINE 3-Error No crypto engine is found due to lack of resource or unsupported feature requested Failed to select a suitable crypto engine because requested packet path not available or requested feature not supported ipsec-getvpn "Check policy configured on KS" GDOI-3-GM_NO_IPSEC_FLOWS 3-Error IPSec FLOW limit possibly reached Hardware Limitation for IPSec Flow limit Reached. Cannot create any more IPSec SAs ipsec-getvpn "Contact the Group member's administrator." GDOI-3-GM_NO_IPSEC_FLOWS 3-Error IPSec FLOW limit possibly reached Hardware Limitation for IPSec Flow limit Reached. Cannot create any more IPSec SAs ipsec-getvpn "Contact the Group member's administrator." GDOI-3-IPSEC_INITIATE_GM_REGISTER_IGNORE 3-Error IPSEC triggering registration for group [chars] too frequently. Ignore the request as registartion has already been scheduled to occur in [dec] msec. GM detects IPSEC triggering registration for the group too frequently. GDOI will ignore the request as registration has already been scheduled. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-IPSEC_INITIATE_GM_REGISTER_IGNORE 3-Error IPSEC triggering registration for group [chars] too frequently. Ignore the request as registartion has already been scheduled to occur in [dec] msec. GM detects IPSEC triggering registration for the group too frequently. GDOI will ignore the request as registration has already been scheduled. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-IPSEC_INITIATE_GM_REGISTER_POSTPONE 3-Error IPSEC triggering registration for group [chars] too frequently. Postpone the registration to occur in [dec] msec. GM detects IPSEC triggering registration for the group too frequently. GDOI will rate-limit and postpone the registration. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-IPSEC_INITIATE_GM_REGISTER_POSTPONE 3-Error IPSEC triggering registration for group [chars] too frequently. Postpone the registration to occur in [dec] msec. GM detects IPSEC triggering registration for the group too frequently. GDOI will rate-limit and postpone the registration. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-KS_BAD_ID 3-Error Registration: [chars] config mismatch between KS and the GM [inet] in the group [chars]. During GDOI registration protocol a configuration mismatch between local key server and group member. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-KS_BAD_ID 3-Error Registration: [chars] config mismatch between KS and the GM [inet] in the group [chars]. During GDOI registration protocol a configuration mismatch between local key server and group member. ipsec-getvpn "Contact the Group member's administrator." GDOI-3-KS_BLACKHOLE_ACK 3-Error KS blackholing GM [inet] in group [chars]. Key server has reached a condition of blackholing messages from GM Some might consider this a hostile event. ipsec-getvpn - GDOI-3-KS_BLACKHOLE_ACK 3-Error KS blackholing GM [inet] in group [chars]. Key server has reached a condition of blackholing messages from GM Some might consider this a hostile event. ipsec-getvpn - GDOI-3-KS_GM_REVOKED 3-Error Re-Key: GM [inet] revoked by KS in the group [chars]. During Re-key protocol an unauthorized member tried to join a group. Some might consider this a hostile event. ipsec-getvpn "Contact the Key Server's administrator." GDOI-3-KS_GM_REVOKED 3-Error Re-Key: GM [inet] revoked by KS in the group [chars]. During Re-key protocol an unauthorized member tried to join a group. Some might consider this a hostile event. ipsec-getvpn "Contact the Key Server's administrator." GDOI-3-KS_MAJOR_VERSION_MISMATCH 3-Error COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] COOP-KS has a non-compatible major version. ipsec-getvpn "Check GDOI version compatibility on KS" GDOI-3-KS_MAJOR_VERSION_MISMATCH 3-Error COOP-KS Major Version mismatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] COOP-KS has a non-compatible major version. ipsec-getvpn "Check GDOI version compatibility on KS" GDOI-3-KS_NO_SID_AVAILABLE 3-Error GMs for group [chars] need SIDs but this KS has no KS SIDs configured or no more SIDs available. This KS has a counter-mode transform configured requiring SIDs and either has no KSSIDs configured or has run out of SIDs. Registering GMs will not be able to register successfully until more KSSIDs are configured on this KS. ipsec-getvpn "Check the configured KSSIDs for this KS by issuing " GDOI-3-KS_NO_SID_AVAILABLE 3-Error GMs for group [chars] need SIDs but this KS has no KS SIDs configured or no more SIDs available. This KS has a counter-mode transform configured requiring SIDs and either has no KSSIDs configured or has run out of SIDs. Registering GMs will not be able to register successfully until more KSSIDs are configured on this KS. ipsec-getvpn "Check the configured KSSIDs for this KS by issuing " GDOI-3-KS_REKEY_AUTH_KEY_LENGTH_INSUFFICIENT 3-Error Rejected [chars] change: using sig-hash algorithm [chars] requires an authentication key length of at least [dec] bits [dec] blocks in bytes Using a sig-hash algorithm for rekeys requires that the RSA key modulus length for the rekey authentication be at least the length of the hash generated by the sig-hash algorithm plus some padding bytes. If the RSA key modulus length is not large enough the Key Server administrator needs to generate a new RSA key pair wit a sufficient length. ipsec-getvpn "Contact the Key Server's administrator to re-generate the RSA " "key pair with at least the modulus length given in the syslog." GDOI-3-KS_REKEY_AUTH_KEY_LENGTH_INSUFFICIENT 3-Error Rejected [chars] change: using sig-hash algorithm [chars] requires an authentication key length of at least [dec] bits [dec] blocks in bytes Using a sig-hash algorithm for rekeys requires that the RSA key modulus length for the rekey authentication be at least the length of the hash generated by the sig-hash algorithm plus some padding bytes. If the RSA key modulus length is not large enough the Key Server administrator needs to generate a new RSA key pair wit a sufficient length. ipsec-getvpn "Contact the Key Server's administrator to re-generate the RSA " "key pair with at least the modulus length given in the syslog." GDOI-3-KS_UNAUTHORIZED 3-Error Registration: Unauthorized [inet] tried to join the group [chars]. During GDOI registration protocol an unauthorized member tried to join a group Some might consider this a hostile event. ipsec-getvpn "Contact the Key Server's administrator." GDOI-3-KS_UNAUTHORIZED 3-Error Registration: Unauthorized [inet] tried to join the group [chars]. During GDOI registration protocol an unauthorized member tried to join a group Some might consider this a hostile event. ipsec-getvpn "Contact the Key Server's administrator." GDOI-3-P2P_KGS_INFRA_ERROR 3-Error PIP session with [chars] failed because of KGS Infra failure. Reason = [chars] A Group Member has encountered a KGS Infra failure. ipsec-getvpn LOG_STD_ACTION GDOI-3-P2P_KGS_INFRA_ERROR 3-Error PIP session with [chars] failed because of KGS Infra failure. Reason = [chars] A Group Member has encountered a KGS Infra failure. ipsec-getvpn LOG_STD_ACTION GDOI-3-P2P_PEER_MIGRATE_FAILED 3-Error Failed to install P2P rekey SA with peer [chars] in group [chars] Installation of P2P Rekey SA with an existing peer has failed ipsec-getvpn "Check the status of all peers using the command " " 'show crypto gdoi gm p2p peers' and wait for PIP initiation between " "the failed peers. Traffic distruption may occur." GDOI-3-P2P_PEER_MIGRATE_FAILED 3-Error Failed to install P2P rekey SA with peer [chars] in group [chars] Installation of P2P Rekey SA with an existing peer has failed ipsec-getvpn "Check the status of all peers using the command " " 'show crypto gdoi gm p2p peers' and wait for PIP initiation between " "the failed peers. Traffic distruption may occur." GDOI-3-PIP_PSEUDO_TIME_ERROR 3-Error An Anti-Replay check has failed for PIP in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = %lld sec src_addr = [chars] dst_addr = [chars] - - - GDOI-3-PIP_PSEUDO_TIME_ERROR 3-Error An Anti-Replay check has failed for PIP in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = %lld sec src_addr = [chars] dst_addr = [chars] - - - GDOI-3-PSEUDO_TIME_LARGE 3-Error Pseudotime difference between KS [dec] sec and GM [dec] sec A Group member has received pseudotime which has large difference as compared to own pseudotime ipsec-getvpn - GDOI-3-PSEUDO_TIME_LARGE 3-Error Pseudotime difference between KS [dec] sec and GM [dec] sec A Group member has received pseudotime which has large difference as compared to own pseudotime ipsec-getvpn - GDOI-3-PSEUDO_TIME_TOO_OLD 3-Error Rekey received in group [chars] is too old and fail PST check: my_pst is [dec] sec peer_pst is [dec] sec allowable_skew is [dec] sec A Group member has received pseudotime which has large difference as compared to own pseudotime ipsec-getvpn - GDOI-3-PSEUDO_TIME_TOO_OLD 3-Error Rekey received in group [chars] is too old and fail PST check: my_pst is [dec] sec peer_pst is [dec] sec allowable_skew is [dec] sec A Group member has received pseudotime which has large difference as compared to own pseudotime ipsec-getvpn - GDOI-3-SA_KEK_INSATALL_FAILED 3-Error Failed to install KEK SA KEK SA instalation has failed ipsec-getvpn "Informational message." GDOI-3-SA_KEK_INSATALL_FAILED 3-Error Failed to install KEK SA KEK SA instalation has failed ipsec-getvpn "Informational message." GDOI-3-UNEXPECTED_SIGKEY 3-Error Unexpected Signature Key detected: freeing it Unexpected Signature Key found: freeing the signature key ipsec-getvpn "Informational message" GDOI-3-UNEXPECTED_SIGKEY 3-Error Unexpected Signature Key detected: freeing it Unexpected Signature Key found: freeing the signature key ipsec-getvpn "Informational message" GDOI-3-UNSUPPORTED_TEK_PROTO 3-Error Unexpected TEK Protocol : [dec] Unexpected TEK PROTOCOL ipsec-getvpn "Informational message" GDOI-3-UNSUPPORTED_TEK_PROTO 3-Error Unexpected TEK Protocol : [dec] Unexpected TEK PROTOCOL ipsec-getvpn "Informational message" GDOI-4-COOP_KS_CHECKPT_MISMATCH 4-Warning Coop KS [chars] in group [chars] received Checkpoint Mismatch message. The KS COOP had received a checkpoint mismatch from a KS COOP peer ipsec-getvpn LOG_STD_ACTION GDOI-4-COOP_KS_CHECKPT_MISMATCH 4-Warning Coop KS [chars] in group [chars] received Checkpoint Mismatch message. The KS COOP had received a checkpoint mismatch from a KS COOP peer ipsec-getvpn LOG_STD_ACTION GDOI-4-COOP_KS_CKM_INCOMPATIBLE 4-Warning Found incompatible COOP-KS that cannot support CKM in group [chars]. Please check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately. Found incompatible COOP-KS that cannot support CKM in the group. Network administrator should check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately - LOG_STD_ACTION GDOI-4-COOP_KS_CKM_INCOMPATIBLE 4-Warning Found incompatible COOP-KS that cannot support CKM in group [chars]. Please check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately. Found incompatible COOP-KS that cannot support CKM in the group. Network administrator should check 'show crypto gdoi feature ckm'and upgrade the incompatible KS immediately - LOG_STD_ACTION GDOI-4-COOP_KS_RBLY_FAILED 4-Warning Coop KS [chars] in group [chars] session Reassembly failed in TransID [dec] The KS COOP had an error reassmbling a packet from a peer KS ipsec-getvpn LOG_STD_ACTION GDOI-4-COOP_KS_RBLY_FAILED 4-Warning Coop KS [chars] in group [chars] session Reassembly failed in TransID [dec] The KS COOP had an error reassmbling a packet from a peer KS ipsec-getvpn LOG_STD_ACTION GDOI-4-COOP_KS_UNAUTH 4-Warning Contact from unauthorized KS [chars] in group [chars] at local address [chars] Possible MISCONFIG of peer/local address - - - GDOI-4-COOP_KS_UNAUTH 4-Warning Contact from unauthorized KS [chars] in group [chars] at local address [chars] Possible MISCONFIG of peer/local address - - - GDOI-4-GDOI_ANN_INCONSISTENT_TBAR 4-Warning COOP_KS ANN received from [chars] in group [chars] has inconsistent TBAR setting inconsistent than mine The KS has received an ANN msg from a secondary KS in which the timestamp is too old ipsec-getvpn - GDOI-4-GDOI_ANN_INCONSISTENT_TBAR 4-Warning COOP_KS ANN received from [chars] in group [chars] has inconsistent TBAR setting inconsistent than mine The KS has received an ANN msg from a secondary KS in which the timestamp is too old ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_LARGE 4-Warning COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself. Adjust to new PST:\n my_old_pst is %llu sec peer_pst is %llu sec - ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_LARGE 4-Warning COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself. Adjust to new PST:\n my_old_pst is %llu sec peer_pst is %llu sec - ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_LARGE_NO_UPDATE 4-Warning COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself:\n my_pst is %llu sec peer_pst is %llu sec - ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_LARGE_NO_UPDATE 4-Warning COOP_KS ANN received from KS [chars] in group [chars] has PST bigger than myself:\n my_pst is %llu sec peer_pst is %llu sec - ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_TOO_OLD 4-Warning COOP_KS ANN from KS [chars] in group [chars] is too old and fail PST check:\n my_pst is %llu sec peer_pst is %llu sec allowable_skew is [dec] sec The KS has received an ANN msg from a primary KS in which the timestamp is too old ipsec-getvpn - GDOI-4-GDOI_ANN_TIMESTAMP_TOO_OLD 4-Warning COOP_KS ANN from KS [chars] in group [chars] is too old and fail PST check:\n my_pst is %llu sec peer_pst is %llu sec allowable_skew is [dec] sec The KS has received an ANN msg from a primary KS in which the timestamp is too old ipsec-getvpn - GDOI-4-GM_DELETE 4-Warning GM [chars] deleted from group [chars]. A group member has been deleted in a group from Key Server ipsec-getvpn "Informational message" GDOI-4-GM_DELETE 4-Warning GM [chars] deleted from group [chars]. A group member has been deleted in a group from Key Server ipsec-getvpn "Informational message" GDOI-4-GM_HASH_FAIL 4-Warning Registration: BadNo hash in message sent by the KS [inet] During GDOI registration protocol a message sent by the Key server has bad or no hash . ipsec-getvpn "Contact the Key Server's administrator." GDOI-4-GM_HASH_FAIL 4-Warning Registration: BadNo hash in message sent by the KS [inet] During GDOI registration protocol a message sent by the Key server has bad or no hash . ipsec-getvpn "Contact the Key Server's administrator." GDOI-4-GM_MINOR_VERSION_MISMATCH 4-Warning GM [inet] Minor Version mismatch. Use 'show crypto gdoi ks members' to see GM versions GM has different minor version. ipsec-getvpn "show crypto gdoi ks members" GDOI-4-GM_MINOR_VERSION_MISMATCH 4-Warning GM [inet] Minor Version mismatch. Use 'show crypto gdoi ks members' to see GM versions GM has different minor version. ipsec-getvpn "show crypto gdoi ks members" GDOI-4-GM_PFS_RE_REGISTER 4-Warning Start PFS triggered re-registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars] Received PFS Rekey Hence re-registring to download new policy. ipsec-getvpn LOG_STD_ACTION GDOI-4-GM_PFS_RE_REGISTER 4-Warning Start PFS triggered re-registration to KS [chars] for group [chars] using address [chars] fvrf [chars] ivrf [chars] Received PFS Rekey Hence re-registring to download new policy. ipsec-getvpn LOG_STD_ACTION GDOI-4-GM_RE_REGISTER 4-Warning The IPSec SA created for group [chars] may have expired/been cleared or didn't go through. Re-register to KS. The IPSec SA created for one group may have expired/been cleared or didn't go through need to re-register to KS. ipsec-getvpn LOG_STD_ACTION GDOI-4-GM_RE_REGISTER 4-Warning The IPSec SA created for group [chars] may have expired/been cleared or didn't go through. Re-register to KS. The IPSec SA created for one group may have expired/been cleared or didn't go through need to re-register to KS. ipsec-getvpn LOG_STD_ACTION GDOI-4-GM_RECOVERY_REGISTRATION 4-Warning GM recovery re-registration for group [chars] will start in a randomly chosen period of [dec] sec GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy - "Informational message." GDOI-4-GM_RECOVERY_REGISTRATION 4-Warning GM recovery re-registration for group [chars] will start in a randomly chosen period of [dec] sec GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy - "Informational message." GDOI-4-GM_RECOVERY_REGISTRATION_POSTPONED 4-Warning Detects data error in group [chars] but the previous recovery/rekey has occured within the last recovery-check interval. Postpone recovery registration to start in [dec] sec GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy - "Informational message." GDOI-4-GM_RECOVERY_REGISTRATION_POSTPONED 4-Warning Detects data error in group [chars] but the previous recovery/rekey has occured within the last recovery-check interval. Postpone recovery registration to start in [dec] sec GM recovery feature detects dataplane error and will re-register to KS to refresh keys and policy - "Informational message." GDOI-4-GM_RECV_DELETE 4-Warning GM received delete-msg from KS in group [chars]. TEKs lifetime are reduced and re-registration will start before SA expiry A messages sent by the KS to delete the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_DELETE 4-Warning GM received delete-msg from KS in group [chars]. TEKs lifetime are reduced and re-registration will start before SA expiry A messages sent by the KS to delete the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_DELETE_IMMEDIATE 4-Warning GM receive REMOVAL-NOW in group [chars] to cleanup downloaded policy now. Re-registration will start in a randomly chosen period of [dec] sec A messages sent by the KS to delete the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_DELETE_IMMEDIATE 4-Warning GM receive REMOVAL-NOW in group [chars] to cleanup downloaded policy now. Re-registration will start in a randomly chosen period of [dec] sec A messages sent by the KS to delete the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_POLICY_REPLACE_NOW 4-Warning GM received policy replace now rekey from KS in group [chars]. A messages sent by the KS to immediately replace SAs policies on the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_POLICY_REPLACE_NOW 4-Warning GM received policy replace now rekey from KS in group [chars]. A messages sent by the KS to immediately replace SAs policies on the GM has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_RE_AUTH 4-Warning GM received Re-auth-msg from KS in group [chars]. re-registration will start before SA expiry A message sent by the KS to have a GM re-auth has been received. ipsec-getvpn "Informational message." GDOI-4-GM_RECV_RE_AUTH 4-Warning GM received Re-auth-msg from KS in group [chars]. re-registration will start before SA expiry A message sent by the KS to have a GM re-auth has been received. ipsec-getvpn "Informational message." GDOI-4-GM_REJECTING_SA_PAYLOAD 4-Warning Registration: Policy in SA payload sent by KS [inet] rejected by GM in the group [chars] reason [chars]. During GDOI registration protocol a proposal sent by the key server was refused by the local group member. ipsec-getvpn "Contact the Key server's administrator." GDOI-4-GM_REJECTING_SA_PAYLOAD 4-Warning Registration: Policy in SA payload sent by KS [inet] rejected by GM in the group [chars] reason [chars]. During GDOI registration protocol a proposal sent by the key server was refused by the local group member. ipsec-getvpn "Contact the Key server's administrator." GDOI-4-GM_REKEY_NOT_RECD 4-Warning GM did not receive rekey from KS [inet] in group [chars]. GM has not received a rekey message from a key server in a group Currently Unimplemented. ipsec-getvpn "Informational message" GDOI-4-GM_REKEY_NOT_RECD 4-Warning GM did not receive rekey from KS [inet] in group [chars]. GM has not received a rekey message from a key server in a group Currently Unimplemented. ipsec-getvpn "Informational message" GDOI-4-GM_SA_TRACK_SET_EOT_ERROR 4-Warning Group [chars] encountered error in setting EOT object ID [dec] to state [chars]. GM SA TRACK state change occur but fail to update EOT object ID accordingly - "Informational message. Check to make sure the EOT " "object ID is configured properly" GDOI-4-GM_SA_TRACK_SET_EOT_ERROR 4-Warning Group [chars] encountered error in setting EOT object ID [dec] to state [chars]. GM SA TRACK state change occur but fail to update EOT object ID accordingly - "Informational message. Check to make sure the EOT " "object ID is configured properly" GDOI-4-KS_GM_REJECTS_SA_PAYLOAD 4-Warning Registration: GM [inet] rejected a policy in the SA proposal sent by KS in the group [chars]. During GDOI registration protocol a proposal sent by the key server was refused by the group member. ipsec-getvpn "Contact the Group member's administrator." GDOI-4-KS_GM_REJECTS_SA_PAYLOAD 4-Warning Registration: GM [inet] rejected a policy in the SA proposal sent by KS in the group [chars]. During GDOI registration protocol a proposal sent by the key server was refused by the group member. ipsec-getvpn "Contact the Group member's administrator." GDOI-4-KS_HASH_FAIL 4-Warning Registration: BadNo Hash in Message sent by the GM [inet] During GDOI registration protocol a message sent by the Group member has bad or no hash . ipsec-getvpn "Contact the Group member's administrator." GDOI-4-KS_HASH_FAIL 4-Warning Registration: BadNo Hash in Message sent by the GM [inet] During GDOI registration protocol a message sent by the Group member has bad or no hash . ipsec-getvpn "Contact the Group member's administrator." GDOI-4-KS_MINOR_VERSION_MISMATCH 4-Warning COOP-KS Minor Version mistmatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] Coop KS has different minor version. ipsec-getvpn "show crypto gdoi ks coop" GDOI-4-KS_MINOR_VERSION_MISMATCH 4-Warning COOP-KS Minor Version mistmatch in group [chars]. My version is [dec].[dec].[dec] peer [chars] has version [dec].[dec].[dec] Coop KS has different minor version. ipsec-getvpn "show crypto gdoi ks coop" GDOI-4-KS_UNSOL_ACK 4-Warning KS received unsolicited ACK from GM [inet] in group [chars]. Key server has received an unsolicited ACK from a past GM or is under a DOS attack. Some might consider this a hostile event. ipsec-getvpn - GDOI-4-KS_UNSOL_ACK 4-Warning KS received unsolicited ACK from GM [inet] in group [chars]. Key server has received an unsolicited ACK from a past GM or is under a DOS attack. Some might consider this a hostile event. ipsec-getvpn - GDOI-4-LKH_GM_DELETE 4-Warning GM [inet] deleted from LKH in group [chars]. A Group member has been deleted in a group from LKH ipsec-getvpn - GDOI-4-LKH_GM_DELETE 4-Warning GM [inet] deleted from LKH in group [chars]. A Group member has been deleted in a group from LKH ipsec-getvpn - GDOI-4-NEWER_GM_VERSION_REGISTER 4-Warning WARNING: GM [chars] registers to group [chars] with newer GDOI version than KS. Please check'show crypto gdoi ks members' and 'show crypto gdoi feature' to ensure all GMs can support the GETVPN features enabled. - ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-4-NEWER_GM_VERSION_REGISTER 4-Warning WARNING: GM [chars] registers to group [chars] with newer GDOI version than KS. Please check'show crypto gdoi ks members' and 'show crypto gdoi feature' to ensure all GMs can support the GETVPN features enabled. - ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-4-REJECT_GM_CKM_REGISTER 4-Warning Reject registration of GM [inet] in group [chars] as it has CKM enabled but this secondaryKS has not sync up all KGS params yet Reject GM registration because this is a secondaryKS and it has not received KGS seed and rekey-epoch from primaryKS yet - LOG_STD_ACTION GDOI-4-REJECT_GM_CKM_REGISTER 4-Warning Reject registration of GM [inet] in group [chars] as it has CKM enabled but this secondaryKS has not sync up all KGS params yet Reject GM registration because this is a secondaryKS and it has not received KGS seed and rekey-epoch from primaryKS yet - LOG_STD_ACTION GDOI-4-REJECT_GM_VERSION_REGISTER 4-Warning Reject registration of GM [inet] ver 0x[hec] in group [chars] as it Reject GM registration because it cannot support the GETVPN features enabled in the group. ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-4-REJECT_GM_VERSION_REGISTER 4-Warning Reject registration of GM [inet] ver 0x[hec] in group [chars] as it Reject GM registration because it cannot support the GETVPN features enabled in the group. ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-4-RSA_KEYS_MODIFIED 4-Warning WARNING: GMs for group [chars] will re-register due to signature verification failure Rekeys will be dropped by GM as signature verification would fail due to modification of RSA Keys ipsec-getvpn "Informational message" GDOI-4-RSA_KEYS_MODIFIED 4-Warning WARNING: GMs for group [chars] will re-register due to signature verification failure Rekeys will be dropped by GM as signature verification would fail due to modification of RSA Keys ipsec-getvpn "Informational message" GDOI-4-TIMEBASED_REPLAY_FAILED 4-Warning An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = [inet] dst_ip = [inet] - - - GDOI-4-TIMEBASED_REPLAY_FAILED 4-Warning An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = [inet] dst_ip = [inet] - - - GDOI-4-TIMEBASED_REPLAY_FAILED_IPV6 4-Warning An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = %P dst_ip = %P - - - GDOI-4-TIMEBASED_REPLAY_FAILED_IPV6 4-Warning An anti replay check has failed in group [chars]: my_pseudotime = [chars] peer_pseudotime = [chars] replay_window = [dec] sec src_ip = %P dst_ip = %P - - - GDOI-5-COOP_KS_ADD 5-Notice [chars] added as COOP Key Server in group [chars]. A key server has been added to the list of cooperative key servers in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_ADD 5-Notice [chars] added as COOP Key Server in group [chars]. A key server has been added to the list of cooperative key servers in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_ADMN_USRP_PRI 5-Notice Primary role Usurped by KS [chars] in group [chars]. A network adminstrator has made the local KS as primary by means of a CLI command. Currently Unimplemented. ipsec-getvpn "Informational message" GDOI-5-COOP_KS_ADMN_USRP_PRI 5-Notice Primary role Usurped by KS [chars] in group [chars]. A network adminstrator has made the local KS as primary by means of a CLI command. Currently Unimplemented. ipsec-getvpn "Informational message" GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ANN 5-Notice This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as it has not received an ANN with valid PST for prolonged period No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ANN 5-Notice This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as it has not received an ANN with valid PST for prolonged period No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ELECTION 5-Notice This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as the KS election is underway The KS is in the process of electing a primary. Temporarily blocking new GM registrations until the election is complete ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_ELECTION 5-Notice This KS temporarily blocks GM with ip-addr [chars] from registering in group [chars] as the KS election is underway The KS is in the process of electing a primary. Temporarily blocking new GM registrations until the election is complete ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_KSSID 5-Notice This KS is blocking GM with ip-addr [chars] from registering in group [chars] as it has overlapping KS Sender Identifiers KSSID with Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed. ipsec-getvpn "Check the configured KSSIDs for all COOP-KS peers by issuing " GDOI-5-COOP_KS_BLOCK_NEW_GM_REGISTER_KSSID 5-Notice This KS is blocking GM with ip-addr [chars] from registering in group [chars] as it has overlapping KS Sender Identifiers KSSID with Another COOP-KS peer in the group has been configured with a KSSID value that is the same as one configured on this KS. GM registration is blocked as a result until the overlap is fixed. ipsec-getvpn "Check the configured KSSIDs for all COOP-KS peers by issuing " GDOI-5-COOP_KS_ELECTION 5-Notice KS entering election mode in group [chars] Previous Primary = [chars] The local Key server has entered the election process in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_ELECTION 5-Notice KS entering election mode in group [chars] Previous Primary = [chars] The local Key server has entered the election process in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_REACH 5-Notice Reachability restored with Cooperative KS [chars] in group [chars]. The reachability between the configugred cooperative key servers is restored. ipsec-getvpn "Informational message" GDOI-5-COOP_KS_REACH 5-Notice Reachability restored with Cooperative KS [chars] in group [chars]. The reachability between the configugred cooperative key servers is restored. ipsec-getvpn "Informational message" GDOI-5-COOP_KS_REMOVE 5-Notice [chars] removed as COOP Key Server in group [chars]. A key server has been removed from the list of cooperative key servers in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_REMOVE 5-Notice [chars] removed as COOP Key Server in group [chars]. A key server has been removed from the list of cooperative key servers in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_RESUME_NEW_GM_REGISTER 5-Notice This KS will now resume new GM registration functionality in group [chars] This KS will now resume new GM registration functionality ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_RESUME_NEW_GM_REGISTER 5-Notice This KS will now resume new GM registration functionality in group [chars] This KS will now resume new GM registration functionality ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KS_TRANS_TO_PRI 5-Notice KS [chars] in group [chars] transitioned to Primary Previous Primary = [chars] The local Key server transitioned to a primary role from being a secondary server in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_TRANS_TO_PRI 5-Notice KS [chars] in group [chars] transitioned to Primary Previous Primary = [chars] The local Key server transitioned to a primary role from being a secondary server in a group ipsec-getvpn "Informational message" GDOI-5-COOP_KS_VALID_ANN_TIMER_EXPIRED 5-Notice This sec-KS has NOT received an ANN with valid PST for an extended period in group [chars]. It will block new GMs registration temporarily until a valid ANN is received No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received ipsec-getvpn "Informational message" GDOI-5-COOP_KS_VALID_ANN_TIMER_EXPIRED 5-Notice This sec-KS has NOT received an ANN with valid PST for an extended period in group [chars]. It will block new GMs registration temporarily until a valid ANN is received No valid ANN message has been received in this secondary KS for a prolong period. Temporarily blocking new GM registrations until a valid ANN is received ipsec-getvpn "Informational message" GDOI-5-COOP_KSSID_OVERLAP_RESOLVED 5-Notice Resolved overlapping KS Sender Identifiers KSSID Another COOP-KS peer in the group had been configured with a KSSID value that was the same as one configured on this KS but has been resolved so that GM registration is allowed again. ipsec-getvpn LOG_STD_ACTION GDOI-5-COOP_KSSID_OVERLAP_RESOLVED 5-Notice Resolved overlapping KS Sender Identifiers KSSID Another COOP-KS peer in the group had been configured with a KSSID value that was the same as one configured on this KS but has been resolved so that GM registration is allowed again. ipsec-getvpn LOG_STD_ACTION GDOI-5-ESON_POLICY_CHANGE_RESTART1 5-Notice ESON group [chars] policy has changed. Must use 'clear crypto gdoi ks members now' to restart the group Reminder message that ESON configuration has changed. eson-ckm LOG_STD_ACTION GDOI-5-ESON_POLICY_CHANGE_RESTART1 5-Notice ESON group [chars] policy has changed. Must use 'clear crypto gdoi ks members now' to restart the group Reminder message that ESON configuration has changed. eson-ckm LOG_STD_ACTION GDOI-5-ESON_POLICY_CHANGE_RESTART2 5-Notice ESON group [chars] policy has changed. Must use 'crypto gdoi ks replace now' to restart the group Reminder message that ESON configuration has changed. eson-ckm LOG_STD_ACTION GDOI-5-ESON_POLICY_CHANGE_RESTART2 5-Notice ESON group [chars] policy has changed. Must use 'crypto gdoi ks replace now' to restart the group Reminder message that ESON configuration has changed. eson-ckm LOG_STD_ACTION GDOI-5-GM_ACL_MERGE 5-Notice ACL betweem KS and GM in group [chars] merged. The ACL differences between GM and KS are resolved and a merge took place ipsec-getvpn - GDOI-5-GM_ACL_MERGE 5-Notice ACL betweem KS and GM in group [chars] merged. The ACL differences between GM and KS are resolved and a merge took place ipsec-getvpn - GDOI-5-GM_CLEAR_REGISTER 5-Notice Config: GM cleared gdoi configuration for the group [chars]. clear crypto gdoi command has been executed by the local GM ipsec-getvpn "Informational message." GDOI-5-GM_CLEAR_REGISTER 5-Notice Config: GM cleared gdoi configuration for the group [chars]. clear crypto gdoi command has been executed by the local GM ipsec-getvpn "Informational message." GDOI-5-GM_CM_ATTACH 5-Notice Crypto map attached for GM in group [chars]. A crypto map has been attached for the local group member. ipsec-getvpn "Informational message." GDOI-5-GM_CM_ATTACH 5-Notice Crypto map attached for GM in group [chars]. A crypto map has been attached for the local group member. ipsec-getvpn "Informational message." GDOI-5-GM_CM_DETACH 5-Notice Crypto map detached for GM in group [chars]. A crypto map has been detached for the local group member. ipsec-getvpn "Informational message." GDOI-5-GM_CM_DETACH 5-Notice Crypto map detached for GM in group [chars]. A crypto map has been detached for the local group member. ipsec-getvpn "Informational message." GDOI-5-GM_CONV_SA_DUPLEX 5-Notice IPSec SAs converted to Duplex in group [chars] on the GM. IPSec SAs have been converted to bidirectional mode in a group on a GM ipsec-getvpn - GDOI-5-GM_CONV_SA_DUPLEX 5-Notice IPSec SAs converted to Duplex in group [chars] on the GM. IPSec SAs have been converted to bidirectional mode in a group on a GM ipsec-getvpn - GDOI-5-GM_CONV_SA_DUPLEX_LOCAL 5-Notice IPSec SAs converted to Duplex in group [chars] on a GM by a local event. IPSec SAs have been converted to bidirectional mode in a group on a GM by a CLI command ipsec-getvpn - GDOI-5-GM_CONV_SA_DUPLEX_LOCAL 5-Notice IPSec SAs converted to Duplex in group [chars] on a GM by a local event. IPSec SAs have been converted to bidirectional mode in a group on a GM by a CLI command ipsec-getvpn - GDOI-5-GM_DELETE_EXPIRED_KEK 5-Notice KEK expired for group [chars] and was deleted Deleting Expired KEK ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_DELETE_EXPIRED_KEK 5-Notice KEK expired for group [chars] and was deleted Deleting Expired KEK ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_DELETE_EXPIRED_P2P 5-Notice P2P SA with epoch hash 0x[chars] expired for group [chars] and was deleted Deleting Expired P2P ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_DELETE_EXPIRED_P2P 5-Notice P2P SA with epoch hash 0x[chars] expired for group [chars] and was deleted Deleting Expired P2P ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_DELETE_EXPIRED_PIP 5-Notice PIP with SPI 0x[chars] expired for group [chars] and was deleted Deleting Expired PIP ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_DELETE_EXPIRED_PIP 5-Notice PIP with SPI 0x[chars] expired for group [chars] and was deleted Deleting Expired PIP ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_ENABLE_GDOI_CM 5-Notice GM has enabled ACL on GDOI crypto map in group [chars]. Group member has enabled ACL on a GDOI Crypto map in a group with a key server ipsec-getvpn - GDOI-5-GM_ENABLE_GDOI_CM 5-Notice GM has enabled ACL on GDOI crypto map in group [chars]. Group member has enabled ACL on a GDOI Crypto map in a group with a key server ipsec-getvpn - GDOI-5-GM_FAILED_TO_INSTALL_POLICIES 5-Notice FAILED: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars] Failed Policy installation ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_FAILED_TO_INSTALL_POLICIES 5-Notice FAILED: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars] Failed Policy installation ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_INSTALL_POLICIES_SUCCESS 5-Notice SUCCESS: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars] fvrf [chars] ivrf [chars] Policy Installation Success ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_INSTALL_POLICIES_SUCCESS 5-Notice SUCCESS: Installation of Reg/Rekey policies from KS [chars] for group [chars] & gm identity [chars] fvrf [chars] ivrf [chars] Policy Installation Success ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_IV_EXHAUSTED 5-Notice GM for group [chars] exhausted its IV space for interface [chars] and will re-register. This GM is registering to an IPv6 group but erroneously receiving IPv4 policies in rekey ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-5-GM_IV_EXHAUSTED 5-Notice GM for group [chars] exhausted its IV space for interface [chars] and will re-register. This GM is registering to an IPv6 group but erroneously receiving IPv4 policies in rekey ipsec-getvpn "Check GMs can support all GETVPN features enabled " "in KS. Also check output of 'show crypto gdoi " "feature' and 'debug crypto gdoi ks infra detail' " "note: high volume of debugs. " GDOI-5-GM_POLICY_CLEANUP 5-Notice KS downloaded Policy Cleared and Fail Close policy installed for GM [chars] in group [chars] As the Fail close revert option is configured and KS is not reachable or registartion is failed we will remove the KS downloaded policy and apply the Fail close policy back on this GM ipsec-getvpn "Informational message." GDOI-5-GM_POLICY_CLEANUP 5-Notice KS downloaded Policy Cleared and Fail Close policy installed for GM [chars] in group [chars] As the Fail close revert option is configured and KS is not reachable or registartion is failed we will remove the KS downloaded policy and apply the Fail close policy back on this GM ipsec-getvpn "Informational message." GDOI-5-GM_RECV_REKEY 5-Notice Received Rekey for group [chars] from [chars] to [chars] with seq # [dec] spi 0x[hec][hec][hec][hec] Received Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_RECV_REKEY 5-Notice Received Rekey for group [chars] from [chars] to [chars] with seq # [dec] spi 0x[hec][hec][hec][hec] Received Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_REGISTER_UPDATE_TBAR 5-Notice Platform HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] re-register to refresh TBAR info. HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] is re-registering to refresh TBAR info. ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_REGISTER_UPDATE_TBAR 5-Notice Platform HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] re-register to refresh TBAR info. HA forwarding-plane comes online group [chars] gm-identity [chars] fvrf [chars] ivrf [chars] is re-registering to refresh TBAR info. ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_REGS_COMPL 5-Notice Registration to KS [chars] complete for group [chars] using address [chars] fvrf [chars] ivrf [chars] Complete registration ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_REGS_COMPL 5-Notice Registration to KS [chars] complete for group [chars] using address [chars] fvrf [chars] ivrf [chars] Complete registration ipsec-getvpn LOG_STD_ACTION GDOI-5-GM_REKEY_CIPHER_HASH_CHECK_FAIL 5-Notice Rekey cipher/hash [chars] used in Group [chars] is unacceptable The key-server has chosen KEK rekey cipher/hash algorithms which are not acceptable by this group-member - "Contact the Key server's administrator." GDOI-5-GM_REKEY_CIPHER_HASH_CHECK_FAIL 5-Notice Rekey cipher/hash [chars] used in Group [chars] is unacceptable The key-server has chosen KEK rekey cipher/hash algorithms which are not acceptable by this group-member - "Contact the Key server's administrator." GDOI-5-GM_REKEY_TRANS_2_MULTI 5-Notice Group [chars] transitioned to multicast rekey. GM has transitioned from using unicast rekey mechanism to multicast mechanism ipsec-getvpn "Informational message" GDOI-5-GM_REKEY_TRANS_2_MULTI 5-Notice Group [chars] transitioned to multicast rekey. GM has transitioned from using unicast rekey mechanism to multicast mechanism ipsec-getvpn "Informational message" GDOI-5-GM_REKEY_TRANS_2_UNI 5-Notice Group [chars] transitioned to Unicast Rekey. GM has transitioned from using multicast rekey mechanism to unicast mechanism ipsec-getvpn "Informational message" GDOI-5-GM_REKEY_TRANS_2_UNI 5-Notice Group [chars] transitioned to Unicast Rekey. GM has transitioned from using multicast rekey mechanism to unicast mechanism ipsec-getvpn "Informational message" GDOI-5-GM_REKEY_TRANSFORMSET_CHECK_FAIL 5-Notice The transformset [chars] for data-protection in Group [chars] is The key-server has chosen a TEK transformset which is not acceptable by this group-member - "Contact the Key server's administrator." GDOI-5-GM_REKEY_TRANSFORMSET_CHECK_FAIL 5-Notice The transformset [chars] for data-protection in Group [chars] is The key-server has chosen a TEK transformset which is not acceptable by this group-member - "Contact the Key server's administrator." GDOI-5-GM_SA_INGRESS 5-Notice Receive only ACL received from KS [inet] in group [chars]. Received only acl has been received by GM from a KS in a group ipsec-getvpn - GDOI-5-GM_SA_INGRESS 5-Notice Receive only ACL received from KS [inet] in group [chars]. Received only acl has been received by GM from a KS in a group ipsec-getvpn - GDOI-5-GM_UNREGISTER 5-Notice GM left the group [chars]. A Group member has left the group. ipsec-getvpn "Informational message." GDOI-5-GM_UNREGISTER 5-Notice GM left the group [chars]. A Group member has left the group. ipsec-getvpn "Informational message." GDOI-5-IPSEC_INITIATE_GM_REGISTER 5-Notice IPSEC initiate GDOI group [chars] to register IPSEC initiate a GM registration for the group ipsec-getvpn LOG_STD_ACTION GDOI-5-IPSEC_INITIATE_GM_REGISTER 5-Notice IPSEC initiate GDOI group [chars] to register IPSEC initiate a GM registration for the group ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_CLEAR_REGISTER 5-Notice Config: KS cleared gdoi configuration for the group [chars]. clear crypto gdoi command has been executed by the local KS ipsec-getvpn "Informational message." GDOI-5-KS_CLEAR_REGISTER 5-Notice Config: KS cleared gdoi configuration for the group [chars]. clear crypto gdoi command has been executed by the local KS ipsec-getvpn "Informational message." GDOI-5-KS_CONV_SAS_DUPLEX 5-Notice IPSec SAs converted to Duplex in group [chars]. IPSec SAs have been converted to bidirectional mode in a group ipsec-getvpn - GDOI-5-KS_CONV_SAS_DUPLEX 5-Notice IPSec SAs converted to Duplex in group [chars]. IPSec SAs have been converted to bidirectional mode in a group ipsec-getvpn - GDOI-5-KS_CONV_SAS_INGRESS 5-Notice IPSec SAs converted to Ingress in group [chars]. IPSec SAs have been converted to receive only mode in a group ipsec-getvpn - GDOI-5-KS_CONV_SAS_INGRESS 5-Notice IPSec SAs converted to Ingress in group [chars]. IPSec SAs have been converted to receive only mode in a group ipsec-getvpn - GDOI-5-KS_GROUP_ADD 5-Notice Config: KS [inet] added to the Group [chars]. A Config command has been executed to add a Key Server in a group ipsec-getvpn "Informational message." GDOI-5-KS_GROUP_ADD 5-Notice Config: KS [inet] added to the Group [chars]. A Config command has been executed to add a Key Server in a group ipsec-getvpn "Informational message." GDOI-5-KS_GROUP_DELETE 5-Notice Config: KS [inet] removed from the Group [chars]. A Config command has been executed to remove a Key Server from a group ipsec-getvpn "Informational message." GDOI-5-KS_GROUP_DELETE 5-Notice Config: KS [inet] removed from the Group [chars]. A Config command has been executed to remove a Key Server from a group ipsec-getvpn "Informational message." GDOI-5-KS_NACK_GM_EJECT 5-Notice KS ejected GM [inet] in group [chars]. Key server has reached a condition of not receiving an ACK from GM and has been ejected ipsec-getvpn "Informational message" GDOI-5-KS_NACK_GM_EJECT 5-Notice KS ejected GM [inet] in group [chars]. Key server has reached a condition of not receiving an ACK from GM and has been ejected ipsec-getvpn "Informational message" GDOI-5-KS_REGS_COMPL 5-Notice KS completed successful registration in group [chars] with GM [inet]. Key server has successfully completed a registration in a group ipsec-getvpn - GDOI-5-KS_REGS_COMPL 5-Notice KS completed successful registration in group [chars] with GM [inet]. Key server has successfully completed a registration in a group ipsec-getvpn - GDOI-5-KS_REINIT_FINISH 5-Notice Re-initialization of group [chars] completed. A previously triggered re-initialization as signified by a \%GDOI-5-KS_REINIT_GROUP syslog has completed after the expiry of the old TEK. ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_REINIT_FINISH 5-Notice Re-initialization of group [chars] completed. A previously triggered re-initialization as signified by a \%GDOI-5-KS_REINIT_GROUP syslog has completed after the expiry of the old TEK. ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_REINIT_GROUP 5-Notice [chars] for group [chars] and will re-initialize the group. KS has reached one of the following conditions indicated by the first part of the message requiring re-initialization of the group:\n ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_REINIT_GROUP 5-Notice [chars] for group [chars] and will re-initialize the group. KS has reached one of the following conditions indicated by the first part of the message requiring re-initialization of the group:\n ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_REKEY_SYNCUP_2_REPLACE 5-Notice Group [chars] transitioned to primary but no policy generated yet continuing with POLICY REPLACE rekey KS Group has transitioned to new Primary but no policy generated yet to recover from this situation continuing with POLICY REPLACE rekey ipsec-getvpn "Informational message" GDOI-5-KS_REKEY_SYNCUP_2_REPLACE 5-Notice Group [chars] transitioned to primary but no policy generated yet continuing with POLICY REPLACE rekey KS Group has transitioned to new Primary but no policy generated yet to recover from this situation continuing with POLICY REPLACE rekey ipsec-getvpn "Informational message" GDOI-5-KS_REKEY_TRANS_2_MULTI 5-Notice Group [chars] transitioned to multicast rekey. Group has transitioned from using unicast rekey mechanism to multicast mechanism ipsec-getvpn "Informational message" GDOI-5-KS_REKEY_TRANS_2_MULTI 5-Notice Group [chars] transitioned to multicast rekey. Group has transitioned from using unicast rekey mechanism to multicast mechanism ipsec-getvpn "Informational message" GDOI-5-KS_REKEY_TRANS_2_UNI 5-Notice Group [chars] transitioned to Unicast Rekey. Group has transitioned from using multicast rekey mechanism to unicast mechanism ipsec-getvpn "Informational message" GDOI-5-KS_REKEY_TRANS_2_UNI 5-Notice Group [chars] transitioned to Unicast Rekey. Group has transitioned from using multicast rekey mechanism to unicast mechanism ipsec-getvpn "Informational message" GDOI-5-KS_SEND_MCAST_REKEY 5-Notice Sending Multicast Rekey [chars]for group [chars] from address [chars] to [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec] Sending Multicast Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_SEND_MCAST_REKEY 5-Notice Sending Multicast Rekey [chars]for group [chars] from address [chars] to [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec] Sending Multicast Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_SEND_UNICAST_REKEY 5-Notice Sending Unicast Rekey [chars]for group [chars] from address [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec] Sending Unicast Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_SEND_UNICAST_REKEY 5-Notice Sending Unicast Rekey [chars]for group [chars] from address [chars] with seq # [dec] spi: 0x[hec][hec][hec][hec] Sending Unicast Rekey ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_USING_DEFAULT_TRANSFORM 5-Notice GETVPN is using default transforms for profile [chars] Using default transformset ipsec-getvpn LOG_STD_ACTION GDOI-5-KS_USING_DEFAULT_TRANSFORM 5-Notice GETVPN is using default transforms for profile [chars] Using default transformset ipsec-getvpn LOG_STD_ACTION GDOI-5-LKH_DISABLE 5-Notice LKH disabled in group [chars]. LKH has been disabled in a group ipsec-getvpn - GDOI-5-LKH_DISABLE 5-Notice LKH disabled in group [chars]. LKH has been disabled in a group ipsec-getvpn - GDOI-5-LKH_ENABLE 5-Notice LKH enabled in group [chars]. LKH has been enabled in a group ipsec-getvpn - GDOI-5-LKH_ENABLE 5-Notice LKH enabled in group [chars]. LKH has been enabled in a group ipsec-getvpn - GDOI-5-POLICY_CHANGE 5-Notice GDOI group [chars] policy has changed. Use 'crypto gdoi ks rekey' to send a rekey or the changes will be send in the next scheduled rekey Reminder message that GDOI configuration has changed. ipsec-getvpn LOG_STD_ACTION GDOI-5-POLICY_CHANGE 5-Notice GDOI group [chars] policy has changed. Use 'crypto gdoi ks rekey' to send a rekey or the changes will be send in the next scheduled rekey Reminder message that GDOI configuration has changed. ipsec-getvpn LOG_STD_ACTION GDOI-5-POLICY_CHANGE_ERROR_MULTIPLE_PORTS 5-Notice Multiple ports detected for ACL [chars] which is not supported. WARNING: No TEK policy will be created. Informs user that there is an error in the ACL with regards to the number of ports. ipsec-getvpn LOG_STD_ACTION GDOI-5-POLICY_CHANGE_ERROR_MULTIPLE_PORTS 5-Notice Multiple ports detected for ACL [chars] which is not supported. WARNING: No TEK policy will be created. Informs user that there is an error in the ACL with regards to the number of ports. ipsec-getvpn LOG_STD_ACTION GDOI-5-POLICY_CHANGE_TO_SUITEB 5-Notice Group [chars] changed to Suite-B policy. Use 'crypto gdoi ks rekey' to generate the new Suite-B policy and cause all GMs to re-register to download SIDs or this will happen in the next scheduled rekey Migrating from non-Suite-B to Suite-B policy requires that the user issues 'crypto gdoi ks rekey' like any other POLICY_CHANGE but this will cause a re-initialization rather than just a rekey. ipsec-getvpn LOG_STD_ACTION GDOI-5-POLICY_CHANGE_TO_SUITEB 5-Notice Group [chars] changed to Suite-B policy. Use 'crypto gdoi ks rekey' to generate the new Suite-B policy and cause all GMs to re-register to download SIDs or this will happen in the next scheduled rekey Migrating from non-Suite-B to Suite-B policy requires that the user issues 'crypto gdoi ks rekey' like any other POLICY_CHANGE but this will cause a re-initialization rather than just a rekey. ipsec-getvpn LOG_STD_ACTION GDOI-5-SA_KEK_UPDATED 5-Notice SA KEK was updated 0x%08X%08X%08X%08X KEK was updated in the Registration/Rekey and a new KEK SA was created ipsec-getvpn "Informational message." GDOI-5-SA_KEK_UPDATED 5-Notice SA KEK was updated 0x%08X%08X%08X%08X KEK was updated in the Registration/Rekey and a new KEK SA was created ipsec-getvpn "Informational message." GDOI-5-SA_PIP_UPDATED 5-Notice SA PIP was updated 0x[chars] PIP was updated in Registration/Rekey and a new PIP SA was created ipsec-getvpn "Informational message." GDOI-5-SA_PIP_UPDATED 5-Notice SA PIP was updated 0x[chars] PIP was updated in Registration/Rekey and a new PIP SA was created ipsec-getvpn "Informational message." GDOI-5-SA_TEK_UPDATED 5-Notice SA TEK was updated TEK was updated in the Registration/Rekey and a new TEK IPSEC SA was created ipsec-getvpn "Informational message." GDOI-5-SA_TEK_UPDATED 5-Notice SA TEK was updated TEK was updated in the Registration/Rekey and a new TEK IPSEC SA was created ipsec-getvpn "Informational message." GDOI-5-TEK_ATD_TIMER_STARTED 5-Notice TEK ATD Timer started for [dec] seconds New TEK will be installed once ATD timer expires TEK ATD timer started and new TEK will be installed after atd timer expiry ipsec-getvpn LOG_STD_ACTION GDOI-5-TEK_ATD_TIMER_STARTED 5-Notice TEK ATD Timer started for [dec] seconds New TEK will be installed once ATD timer expires TEK ATD timer started and new TEK will be installed after atd timer expiry ipsec-getvpn LOG_STD_ACTION GDOI-6-COOP_KS_VER_TRANSIT 6-Information Coop KS [chars] protocol version transits from version 1.0.1 to 2.0.0 The KS is transitioning to a new version. ipsec-getvpn LOG_STD_ACTION GDOI-6-COOP_KS_VER_TRANSIT 6-Information Coop KS [chars] protocol version transits from version 1.0.1 to 2.0.0 The KS is transitioning to a new version. ipsec-getvpn LOG_STD_ACTION GDOI-6-KS_FIRST_GM 6-Information Re-key: First GM [inet] seen by KS in the group [chars]. Local key server has received the first group member joining the group ipsec-getvpn "Informational message." GDOI-6-KS_FIRST_GM 6-Information Re-key: First GM [inet] seen by KS in the group [chars]. Local key server has received the first group member joining the group ipsec-getvpn "Informational message." GDOI-6-KS_LAST_GM 6-Information Re-key: Last GM [inet] left the group [chars]. Last group member has left the group on the local key server ipsec-getvpn "Informational message." GDOI-6-KS_LAST_GM 6-Information Re-key: Last GM [inet] left the group [chars]. Last group member has left the group on the local key server ipsec-getvpn "Informational message." GE_LINK-3-MDIO_ERR 3-Error [chars] error for controller [dec] port [dec] Error in accessing GigE Transceiver cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" GE_LINK-3-SW_ERR 3-Error [chars] error in GE pair [dec] port [dec] Internal software error cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" GE_LINK-4-SWITCHOVER_ERR 4-Warning switchover to primary port in GE pair is suppressed due to port instability - cmts-platform "check GE link" GE_LINK-5-AUTONEGOTIATION 5-Notice Waiting for completed A/N in GE pair [dec] primary port - cmts-platform "If persistent check peer GigabitEthernet port" GE_LINK-5-SWITCHOVER_PRI 5-Notice primary port set active for GE pair [dec] GE link is restored for primary port cmts-platform "if not expected check secondary port in GE pair" GE_LINK-5-SWITCHOVER_SEC 5-Notice secondary port set active for GE pair [dec] GE link is lost for primary port cmts-platform "if not expected check secondary port in GE pair" GE_LINK-5-UPDOWN 5-Notice Link status is [chars] for GE pair [dec] port [dec] Link Status Change detected for GigE Transceiver cmts-platform "If not expected check GIGE link" GE_LINK-6-PHY_EVENT 6-Information PHY [chars] event detected for phy [dec] port [dec] Link Event detected for non-SFP port of GigE Transceiver cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" GEN_DB-3-INVALID_CLIENT_TYPE 3-Error [chars]: Invalid client type got [dec] must be between 0 and [dec] This message indicates that client type is outside the expected range - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-INVALID_RECORD_KEY 3-Error [chars]: invalid record key * This message indicates that the record key is invalid - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-KEY_FUNC_DOESNT_EXIST 3-Error [chars]: Key function does not exist This message indicates that key function being considered does not exist in the database definition - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-LIST_FAIL 3-Error [chars]:[chars] This message indicates that a list operations such as enqueue dequeu failed - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-LIST_FAIL_FOR_RECORD 3-Error [chars]:[dec]:[chars] This message indicates that a list operations such as enqueue dequeu failed - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-NO_KEY_FUNC 3-Error [chars]: [chars][chars] This message indicates that key functions are missing from the database handle or key function is a NULL Pointer - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-NULL_DB_HNDL 3-Error NULL Database Handle [chars] This message indicates the database handle was NULL - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-NULL_DB_HNDL_ELEMENT 3-Error [chars]: NULL Database Element [chars] This message indicates the database handle element was NULL - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-NULL_TREE_NODE 3-Error Node is NULL [chars] This message indicates that the tree node being examined is NULL - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-PARSER_INIT_FAIL 3-Error [chars]:[dec]: Parser Could not be initialized This message indicates that the IOS Parser command could not be initialized - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-RECORD_DELETE_FAIL 3-Error [chars]:[chars] This message indicates that a record could not be deleted - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-UNKNOWN_PARSER_CMD 3-Error [chars]:[dec]: Unknown Parser Command This message indicates that the IOS Parser command was not recognized - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_DB-3-WAVL_FAIL 3-Error [chars]: [chars] This message indicates that a wavl tree operation failed - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GEN_PROXY-3-GPM_ALLOC_FAILED 3-Error GPM allocation for reply failed pak_size [hec] reply_size [hec] GPM could not be allocated for reply. cpp-ucode LOG_STD_ACTION GEN_PROXY-3-IPC_SEND_FAILED 3-Error IPC send reply failed [chars] GEN proxy failed to send of reply to IPC msg. cpp-ucode LOG_STD_ACTION GEN_PROXY-3-IPC_UNHANDLED 3-Error failure An unknown message type: [dec] was received by the Generic Client Proxy. cpp-ucode LOG_STD_ACTION GEN_PROXY-3-REPLY_MSG 3-Error wrong version [dec] An incorrect SBS message was received by the Generic Client Proxy. cpp-ucode LOG_STD_ACTION GEN_PROXY-3-STACK_ALLOC_FAILED 3-Error Stack allocation for reply failed reply_size [hec] Stack space could not be allocated for reply. cpp-ucode LOG_STD_ACTION GENERAL-3-LDP 3-Error ERRMSG_FLAG_TRACEBACK - - - GENERAL-3-LDP 3-Error ERRMSG_FLAG_TRACEBACK - - - GENERAL-3-LDPLIB 3-Error ERRMSG_NOFLAGS - - - GENERAL-3-LDPLIB 3-Error ERRMSG_NOFLAGS - - - GENERIC_SUBBLOCK-2-BUILDXDR 2-Critical Failed to build message for GSB: [chars] An attempt to build a message for distribution of generic subblock failed - LOG_STD_ACTION GENERIC_SUBBLOCK-2-BUILDXDR 2-Critical Failed to build message for GSB: [chars] An attempt to build a message for distribution of generic subblock failed - LOG_STD_ACTION GENERIC_SUBBLOCK-2-GSBNOTISSUAWARE 2-Critical GSB [chars] is not ISSU aware. Cannot distribute it to ISSU-aware slots This GSB is expected to be ISSU aware but it is not. It cannot be distributed safely to ISSU-aware slots as it may not be correctly interpreted - LOG_STD_ACTION GENERIC_SUBBLOCK-2-GSBNOTISSUAWARE 2-Critical GSB [chars] is not ISSU aware. Cannot distribute it to ISSU-aware slots This GSB is expected to be ISSU aware but it is not. It cannot be distributed safely to ISSU-aware slots as it may not be correctly interpreted - LOG_STD_ACTION GENERIC_SUBBLOCK-2-LATE_REGISTER 2-Critical Late registration of GSB type [chars] with id [dec] An attempt to register a new generic subblock type was received after subblocks have already been allocated from the control structure with previously registered types - LOG_STD_ACTION GENERIC_SUBBLOCK-2-LATE_REGISTER 2-Critical Late registration of GSB type [chars] with id [dec] An attempt to register a new generic subblock type was received after subblocks have already been allocated from the control structure with previously registered types - LOG_STD_ACTION GENERIC_SUBBLOCK-2-UNPACKXDR 2-Critical Unpacked [dec] bytes and attempted to consume [dec] bytes for GSB: [chars] A discrepancy was detected between length of message expected versus length of message received - LOG_STD_ACTION GENERIC_SUBBLOCK-2-UNPACKXDR 2-Critical Unpacked [dec] bytes and attempted to consume [dec] bytes for GSB: [chars] A discrepancy was detected between length of message expected versus length of message received - LOG_STD_ACTION GENERIC-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - GENERIC-3-MPLS_TE_EXT_FWDG 3-Error ERRMSG_NOFLAGS - - - GEO_PROXY-3-PROXY_DEBUG_REG_FAILED 3-Error - GEO Conditional Debugging registration failed. cpp-ucode LOG_STD_ACTION GIGASTACK-1-NO_LOOP_DETECT 1-Alert The link neighbor of link [dec] of Gigastack GBIC in [chars] did not respond to the loop detection request. If loop topology is deployed make sure all switches in the stack are running the latest software.\n No acknowledgement for Gigastack loop detection request is received from one of the links on a Gigastack GBIC. Either the neighboring switch does not support Gigastack Loop breaking algorithm or the link between the two Gigastack GBICs is broken. Under this condition a Gigastack loop topology will not be automatically detected and the connectivity between switches in the stack could be lost. - "If loop topology is used in the Gigastack make sure the latest software is running on all switches in the stack. Check the Gigastack GBICs involved to make sure they are functioning." GIGASTACK-1-NO_LOOP_DETECT 1-Alert The link neighbor of link [dec] of Gigastack GBIC in [chars] did not respond to the loop detection request. If loop topology is deployed make sure all switches in the stack are running the latest software.\n No acknowledgement for Gigastack loop detection request is received from one of the links on a Gigastack GBIC. Either the neighboring switch does not support Gigastack Loop breaking algorithm or the link between the two Gigastack GBICs is broken. Under this condition a Gigastack loop topology will not be automatically detected and the connectivity between switches in the stack could be lost. - "If loop topology is used in the Gigastack make sure the latest software is running on all switches in the stack. Check the Gigastack GBICs involved to make sure they are functioning." GIGASTACK-3-INIT_FAILURE 3-Error Gigastack GBIC in [chars] initialization failed. Gigastack GBIC failed POST. firmware "Remove the Gigastack GBIC and re-insert it into the GBIC slot." GIGASTACK-3-INIT_FAILURE 3-Error Gigastack GBIC in [chars] initialization failed. Gigastack GBIC failed POST. firmware "Remove the Gigastack GBIC and re-insert it into the GBIC slot." GIGASTACK-6-LOOP_BROKEN 6-Information Link loss is detected in the Gigastack loop \nLink 2 of the Gigastack GBIC in [chars] is re-enabled. Loop formed by Gigastack modules is broken because of link loss. Link 2 of the Master Loop Breaker is re-enabled to replace the broken link - LOG_STD_NO_ACTION GIGASTACK-6-LOOP_BROKEN 6-Information Link loss is detected in the Gigastack loop \nLink 2 of the Gigastack GBIC in [chars] is re-enabled. Loop formed by Gigastack modules is broken because of link loss. Link 2 of the Master Loop Breaker is re-enabled to replace the broken link - LOG_STD_NO_ACTION GIGASTACK-6-LOOP_DETECTED 6-Information Gigastack GBIC in [chars] is selected as Master Loop Breaker. \nLink 2 of the Gigastack GBIC is disabled to break the loop. Loop is detected in the Gigastack and this Gigastack GBIC is selected as the Master Loop Breaker. Link 2 of this Gigastack GBIC is disabled to break the loop. - LOG_STD_NO_ACTION GIGASTACK-6-LOOP_DETECTED 6-Information Gigastack GBIC in [chars] is selected as Master Loop Breaker. \nLink 2 of the Gigastack GBIC is disabled to break the loop. Loop is detected in the Gigastack and this Gigastack GBIC is selected as the Master Loop Breaker. Link 2 of this Gigastack GBIC is disabled to break the loop. - LOG_STD_NO_ACTION GK_OSP-3-GK_OSP_INIT_NOMEM 3-Error \ Not enough emory to initialize GK_OSP subsystem: [chars]. Unable to initialize the gatekeeper OSP subsystem because of low memory conditions. - "Upgrade memory capacity on the router." GK_OSP-3-GK_OSP_INIT_NOMEM 3-Error \ Not enough emory to initialize GK_OSP subsystem: [chars]. Unable to initialize the gatekeeper OSP subsystem because of low memory conditions. - "Upgrade memory capacity on the router." GK_OSP-3-GK_OSP_PARSE_CHAIN_FAIL 3-Error \ Could not install gatekeeper osp CLI. An internal error has occured. - "None. Please report this to customer support." GK_OSP-3-GK_OSP_PARSE_CHAIN_FAIL 3-Error \ Could not install gatekeeper osp CLI. An internal error has occured. - "None. Please report this to customer support." GK-3-ALTGK_CONFIG_ERROR 3-Error \ An error in the alternate gatekeeper configuration was detected. Remote gatekeeper [chars] claims to be part of zone [chars] - - - GK-3-ALTGK_CONFIG_ERROR 3-Error \ An error in the alternate gatekeeper configuration was detected. Remote gatekeeper [chars] claims to be part of zone [chars] - - - GK-3-ALTGK_CONFIG_ERROR_LOCAL 3-Error \ An alternate gatekeeper indicates an alt-gk configuration error on a local zone.\n - - - GK-3-ALTGK_CONFIG_ERROR_LOCAL 3-Error \ An alternate gatekeeper indicates an alt-gk configuration error on a local zone.\n - - - GK-3-CANNOT_TURN_OFF_ATTRIB 3-Error \ Subnet attributes are currently turned ON for\n - - - GK-3-CANNOT_TURN_OFF_ATTRIB 3-Error \ Subnet attributes are currently turned ON for\n - - - GK-3-CONFLICTING_DATA 3-Error \ Static-alias command failed. Endpoint already exists with different [chars].\n Use the \show gatekeeper endpoints\ command to check on existing endp\n\oints. - - - GK-3-CONFLICTING_DATA 3-Error \ Static-alias command failed. Endpoint already exists with different [chars].\n Use the \show gatekeeper endpoints\ command to check on existing endp\n\oints. - - - GK-3-ENDPT_NOT_FOUND 3-Error \ Endpoint not found for specified IP address [inet]. - - - GK-3-ENDPT_NOT_FOUND 3-Error \ Endpoint not found for specified IP address [inet]. - - - GK-3-EXCEED_MAX_LOCAL_ZONE_ALLOWED 3-Error \ Exceeded maximum number of local zones [dec] allowed. - - - GK-3-EXCEED_MAX_LOCAL_ZONE_ALLOWED 3-Error \ Exceeded maximum number of local zones [dec] allowed. - - - GK-3-GK_GUP_INIT_ERROR 3-Error \ An error occurred trying to initialize the Gatekeeper Update Protocol GUP. - - - GK-3-GK_GUP_INIT_ERROR 3-Error \ An error occurred trying to initialize the Gatekeeper Update Protocol GUP. - - - GK-3-GK_SRV_LISTEN_FAIL 3-Error \ Failed to open Gatekeeper Server listening socket. - - - GK-3-GK_SRV_LISTEN_FAIL 3-Error \ Failed to open Gatekeeper Server listening socket. - - - GK-3-GK_TMSG_NOMEM 3-Error \ No memory for gk-server transport message block. - - - GK-3-GK_TMSG_NOMEM 3-Error \ No memory for gk-server transport message block. - - - GK-3-GKTMP_SERVER_MARKED_UNUSABLE 3-Error GKTMP Server: [chars][chars] connected to GK: [chars] is marked unusable The Gatekeeper has marked a GKTMP server as unusable when flow\n\ control is configured.The reason for this action could be that the\n\ average response time of the GMTMP server is very high or the number\n\ of messages queued to be sent to the GKTMP server is very high. These\n\ conditions could be caused by an overloaded server or a problem with\n\ the TCP connection between the server and the Gatekeeper. voice-h323 "Check the operational status of of the GKTMP server and the\n\ network link between the server and the Gatekeeper. If both are\n\ operational enter the show running-config and\n\ show gatekeeper servers commands and verify\n\ the status of the GKTMP server. Enter the debug gatekeeper\n\ server on the Gatekeeper to enable debugging on the\n\ gatekeeper server. Gather this information contact your Cisco\n\ technical support representative and provide the representative\n\ with the gathered information." GK-3-GKTMP_SERVER_MARKED_UNUSABLE 3-Error GKTMP Server: [chars][chars] connected to GK: [chars] is marked unusable The Gatekeeper has marked a GKTMP server as unusable when flow\n\ control is configured.The reason for this action could be that the\n\ average response time of the GMTMP server is very high or the number\n\ of messages queued to be sent to the GKTMP server is very high. These\n\ conditions could be caused by an overloaded server or a problem with\n\ the TCP connection between the server and the Gatekeeper. voice-h323 "Check the operational status of of the GKTMP server and the\n\ network link between the server and the Gatekeeper. If both are\n\ operational enter the show running-config and\n\ show gatekeeper servers commands and verify\n\ the status of the GKTMP server. Enter the debug gatekeeper\n\ server on the Gatekeeper to enable debugging on the\n\ gatekeeper server. Gather this information contact your Cisco\n\ technical support representative and provide the representative\n\ with the gathered information." GK-3-GKTMP_SERVER_OFFLINE 3-Error GKTMP Server: [chars][chars] is disconnected with Gatekeeper: [chars] - voice-h323 "Check the operational status of the Gatekeeper and the GKTMP\n\ server. If both are operational check the TCP connection between\n\ the server and the Gatekeeper. Check the output of the show\n\ running-config and show gatekeeper\n\ servers and verify the status of the GKTMP server. Enter\n\ the debug gatekeeper server command on the\n\ Gatekeeper to enable debugging on the gatekeeper server. Collect\n\ this information contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information." GK-3-GKTMP_SERVER_OFFLINE 3-Error GKTMP Server: [chars][chars] is disconnected with Gatekeeper: [chars] - voice-h323 "Check the operational status of the Gatekeeper and the GKTMP\n\ server. If both are operational check the TCP connection between\n\ the server and the Gatekeeper. Check the output of the show\n\ running-config and show gatekeeper\n\ servers and verify the status of the GKTMP server. Enter\n\ the debug gatekeeper server command on the\n\ Gatekeeper to enable debugging on the gatekeeper server. Collect\n\ this information contact your Cisco technical support\n\ representative and provide the representative with the gathered\n\ information." GK-3-GW_PROXY_ADD_COST_FAIL 3-Error \ GW/Proxy add cost failed. Could be out of memory. - - - GK-3-GW_PROXY_ADD_COST_FAIL 3-Error \ GW/Proxy add cost failed. Could be out of memory. - - - GK-3-GW_PROXY_ALIAS_NOT_FOUND 3-Error \ GW/Proxy not found for specified alias name [chars]. - - - GK-3-GW_PROXY_ALIAS_NOT_FOUND 3-Error \ GW/Proxy not found for specified alias name [chars]. - - - GK-3-GW_PROXY_ENDPT_NOT_FOUND 3-Error \ GW/PROXY may not be registered. Add cost failed. - - - GK-3-GW_PROXY_ENDPT_NOT_FOUND 3-Error \ GW/PROXY may not be registered. Add cost failed. - - - GK-3-GW_PROXY_IP_NOT_FOUND 3-Error \ GW/Proxy not found for specified IP adddress [inet]. - - - GK-3-GW_PROXY_IP_NOT_FOUND 3-Error \ GW/Proxy not found for specified IP adddress [inet]. - - - GK-3-INVALID_GK_CMD 3-Error \ To shutdown Gatekeeper use the \shutdown\ command in the Gatekeeper mode. - - - GK-3-INVALID_GK_CMD 3-Error \ To shutdown Gatekeeper use the \shutdown\ command in the Gatekeeper mode. - - - GK-3-MSGCB_TIMER_RUNNING 3-Error \ Message CB freed while timer still running: msgcb state=[dec] status=[dec] timer type=[dec] - - - GK-3-MSGCB_TIMER_RUNNING 3-Error \ Message CB freed while timer still running: msgcb state=[dec] status=[dec] timer type=[dec] - - - GK-3-NO_DISC_PORT 3-Error \ Unable to open or bind to gatekeeper discovery port. Bringup failed. - - - GK-3-NO_DISC_PORT 3-Error \ Unable to open or bind to gatekeeper discovery port. Bringup failed. - - - GK-3-NO_RAS_PORT 3-Error \ Unable to open or bind to RAS well-known port. Bringup failed. - - - GK-3-NO_RAS_PORT 3-Error \ Unable to open or bind to RAS well-known port. Bringup failed. - - - GK-3-PARTIAL_STATIC_ALIAS 3-Error \ Not all aliases were successfully created. Use the \show gatekeeper endpt\ command to check on successful aliases. - - - GK-3-PARTIAL_STATIC_ALIAS 3-Error \ Not all aliases were successfully created. Use the \show gatekeeper endpt\ command to check on successful aliases. - - - GK-3-PROC_CB_NOMEM 3-Error \ No memory for process control block. Gatekeeper bringup failed. - - - GK-3-PROC_CB_NOMEM 3-Error \ No memory for process control block. Gatekeeper bringup failed. - - - GK-3-PROC_EV_NOMEM 3-Error \ No memory for free event queue. Gatekeeper bringup failed. - - - GK-3-PROC_EV_NOMEM 3-Error \ No memory for free event queue. Gatekeeper bringup failed. - - - GK-3-PROC_LRQARRAY_NOMEM 3-Error \ No memory for lrq array. Gatekeeper bringup failed. - - - GK-3-PROC_LRQARRAY_NOMEM 3-Error \ No memory for lrq array. Gatekeeper bringup failed. - - - GK-3-PROC_MSGCB_NOMEM 3-Error \ No memory for IPC message control block. Gatekeeper bringup failed. - - - GK-3-PROC_MSGCB_NOMEM 3-Error \ No memory for IPC message control block. Gatekeeper bringup failed. - - - GK-3-PROC_MSGRING_NOMEM 3-Error \ No memory for msgring. Gatekeeper bringup failed. - - - GK-3-PROC_MSGRING_NOMEM 3-Error \ No memory for msgring. Gatekeeper bringup failed. - - - GK-3-PROC_NOCREAT 3-Error \ Unable to create gatekeeper process. Gatekeeper bringup failed. - - - GK-3-PROC_NOCREAT 3-Error \ Unable to create gatekeeper process. Gatekeeper bringup failed. - - - GK-3-PROC_NOTDOWN 3-Error \ Invalid state [chars]: bringup is only permitted after shut down. - - - GK-3-PROC_NOTDOWN 3-Error \ Invalid state [chars]: bringup is only permitted after shut down. - - - GK-3-PROC_NOTUP 3-Error \ Invalid state [chars]: shutdown is only permitted after bringup. - - - GK-3-PROC_NOTUP 3-Error \ Invalid state [chars]: shutdown is only permitted after bringup. - - - GK-3-SHUTDOWN_WITH_CALLS 3-Error \ Cannot shutdown gatekeeper because there are calls in progress. - - - GK-3-SHUTDOWN_WITH_CALLS 3-Error \ Cannot shutdown gatekeeper because there are calls in progress. - - - GK-3-STATIC_ALIAS_FAILED 3-Error \ static-alias command failed. Could not create endpoint in endpoint dbase. - - - GK-3-STATIC_ALIAS_FAILED 3-Error \ static-alias command failed. Could not create endpoint in endpoint dbase. - - - GK-3-STATIC_ALIAS_GW_FAILED 3-Error \ A static endpoint was added into the database but failed to create a gateway.\n - - - GK-3-STATIC_ALIAS_GW_FAILED 3-Error \ A static endpoint was added into the database but failed to create a gateway.\n - - - GK-3-SUBNET_FAILED 3-Error \ Failed to add/modify subnet information for specified subnet [inet]/[inet]. - - - GK-3-SUBNET_FAILED 3-Error \ Failed to add/modify subnet information for specified subnet [inet]/[inet]. - - - GK-3-SUBNET_NO_ATTRIBUTES 3-Error \ Please specify attribute [default | explicit] for this command. - - - GK-3-SUBNET_NO_ATTRIBUTES 3-Error \ Please specify attribute [default | explicit] for this command. - - - GK-3-SUBNET_NOT_FOUND 3-Error \ Subnet not found under specified IP address [inet]/[inet]. - - - GK-3-SUBNET_NOT_FOUND 3-Error \ Subnet not found under specified IP address [inet]/[inet]. - - - GK-3-ZONE_ACTIVE 3-Error \ There are endpoints currently registered in zone [chars]. Zone remove failed - - - GK-3-ZONE_ACTIVE 3-Error \ There are endpoints currently registered in zone [chars]. Zone remove failed - - - GK-3-ZONE_NOT_FOUND 3-Error \ Zone not found for specified Gatekeeper name [chars]. - - - GK-3-ZONE_NOT_FOUND 3-Error \ Zone not found for specified Gatekeeper name [chars]. - - - GK-4-PROC_NOTALL 4-Warning \ Unable to create more than [dec] gk thread processes. - - - GK-4-PROC_NOTALL 4-Warning \ Unable to create more than [dec] gk thread processes. - - - GK-5-GKTMP_SERVER_MARKED_USABLE 5-Notice GKTMP Server: [chars][chars] connected to GK: [chars] is marked usable The Gatekeeper has marked the GKTMP server as usable when flow\n\ control is configured. voice-h323 LOG_STD_NO_ACTION GK-5-GKTMP_SERVER_MARKED_USABLE 5-Notice GKTMP Server: [chars][chars] connected to GK: [chars] is marked usable The Gatekeeper has marked the GKTMP server as usable when flow\n\ control is configured. voice-h323 LOG_STD_NO_ACTION GK-5-GKTMP_SERVER_ONLINE 5-Notice GKTMP Server: [chars][chars] is connected with Gatekeeper: [chars] A connection between a GKTMP server and a gatekeeper has been\n\ established. The connection establishment could be initiated by\n\ either the Gatekeeper or a GKTMP server. voice-h323 LOG_STD_NO_ACTION GK-5-GKTMP_SERVER_ONLINE 5-Notice GKTMP Server: [chars][chars] is connected with Gatekeeper: [chars] A connection between a GKTMP server and a gatekeeper has been\n\ established. The connection establishment could be initiated by\n\ either the Gatekeeper or a GKTMP server. voice-h323 LOG_STD_NO_ACTION GK-5-RX_LRQ_PASSWORD_UPDATED 5-Notice \ LRQ receive password for security password-group '[chars]' has been updated. The Gatekeeper was configured with a LRQ security password-goup that contained the 'effective' keyword. This keyword allows the user to specify a time at which the requested password is to take effect. The log is displayed to inform the user that the time period has expired and the updated password is now in effect. - "This log is only for informational purposes. The user should verify " "that all remote zones associated with this password-group are now " "providing the password in its LRQ messages. Failure to do so will " "result in a LRJ containing a reason of invalid_permission." GK-5-RX_LRQ_PASSWORD_UPDATED 5-Notice \ LRQ receive password for security password-group '[chars]' has been updated. The Gatekeeper was configured with a LRQ security password-goup that contained the 'effective' keyword. This keyword allows the user to specify a time at which the requested password is to take effect. The log is displayed to inform the user that the time period has expired and the updated password is now in effect. - "This log is only for informational purposes. The user should verify " "that all remote zones associated with this password-group are now " "providing the password in its LRQ messages. Failure to do so will " "result in a LRJ containing a reason of invalid_permission." GK-6-ARQ_ACL_BLOCKED_MSG 6-Information \ AnswerCall ARQ with source IP [chars] was blocked by ARQ access list - - - GK-6-ARQ_ACL_BLOCKED_MSG 6-Information \ AnswerCall ARQ with source IP [chars] was blocked by ARQ access list - - - GK-6-GK_CLI_RAS_IP_CHANGED 6-Information \ The IP address which\n has been changed was the gatekeeper's configured RAS address.\n Existing RAS clients will no longer be able to reach the gatekeeper.\n The IP address being changed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically replace the gatekeeper's static RAS address with the new IP address. Since the gatekeeper's old RAS address is no longer valid existing clients which have registered to this gatekeeper via the old RAS address will no longer be able to communicate with this gatekeeper. - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-GK_CLI_RAS_IP_CHANGED 6-Information \ The IP address which\n has been changed was the gatekeeper's configured RAS address.\n Existing RAS clients will no longer be able to reach the gatekeeper.\n The IP address being changed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically replace the gatekeeper's static RAS address with the new IP address. Since the gatekeeper's old RAS address is no longer valid existing clients which have registered to this gatekeeper via the old RAS address will no longer be able to communicate with this gatekeeper. - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-GK_CLI_RAS_IP_REMOVED 6-Information \ The IP address which\n has been removed was the gatekeeper's configured RAS address. The\n system will automatically assign a new IP address if available to\n The IP address being removed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically remove the gatekeeper's static RAS address. Since the gatekeeper no longer has a configured RAS address the router will automatically assign an IP address if there is any to the gatekeeper. Existing clients which have registered to - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-GK_CLI_RAS_IP_REMOVED 6-Information \ The IP address which\n has been removed was the gatekeeper's configured RAS address. The\n system will automatically assign a new IP address if available to\n The IP address being removed at the interface was statically assigned to the gatekeeper for its RAS signaling via the \zone local\ command. This action will automatically remove the gatekeeper's static RAS address. Since the gatekeeper no longer has a configured RAS address the router will automatically assign an IP address if there is any to the gatekeeper. Existing clients which have registered to - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-GK_CLOSE_SRV_CONNECTION 6-Information \ The connection to GKTMP server [chars][inet] appears to be hung Messages are being backed up in the gatekeeper's write queue in the connection with the specified server name. The connection is assumed to have gone bad and the gatekeeper is closing the connection. This implies that messages will not be sent to that server for processing until either the gatekeeper or the server re-initiates the connection. - "Check with the specified server for possible connection error." GK-6-GK_CLOSE_SRV_CONNECTION 6-Information \ The connection to GKTMP server [chars][inet] appears to be hung Messages are being backed up in the gatekeeper's write queue in the connection with the specified server name. The connection is assumed to have gone bad and the gatekeeper is closing the connection. This implies that messages will not be sent to that server for processing until either the gatekeeper or the server re-initiates the connection. - "Check with the specified server for possible connection error." GK-6-GK_FLOAT_RAS_IP_CHANGED 6-Information \ The gatekeeper's RAS address\n has been automatically changed by the system. Existing RAS clients\n may no longer be able to reach the gatekeeper.\n The IP address being changed at the interface causes the system to look for a better IP address to be used for the gatekeeper's RAS address. existing clients which have registered to this gatekeeper via the old RAS address may no longer be able to communicate with this gatekeeper. - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-GK_FLOAT_RAS_IP_CHANGED 6-Information \ The gatekeeper's RAS address\n has been automatically changed by the system. Existing RAS clients\n may no longer be able to reach the gatekeeper.\n The IP address being changed at the interface causes the system to look for a better IP address to be used for the gatekeeper's RAS address. existing clients which have registered to this gatekeeper via the old RAS address may no longer be able to communicate with this gatekeeper. - "It is the user's responsibility to notify existing RAS clients to " "re-register their systems to the gatekeeper's new RAS address as " "shown in the \"show gatekeeper zone status\" display" GK-6-LRQ_ACL_BLOCKED_MSG 6-Information \ LRQ from IP [chars] was blocked by LRQ access list - - - GK-6-LRQ_ACL_BLOCKED_MSG 6-Information \ LRQ from IP [chars] was blocked by LRQ access list - - - GLBP-3-MISCONFIG 3-Error Cannot add MAC address [enet] to interface [chars] - not supported A software or hardware error occurred. - LOG_STD_SH_TECH_ACTION GLBP-4-BADAUTH 4-Warning Bad authentication received from [chars] group [dec] Two routers participating in a Gateway Load Balancing Protocol group disagree on the valid authentication string. - "Use the glbp authentication interface command to repair the " "GLBP authentication discrepancy between the local system " "and the one whose IP address is reported." GLBP-4-BADVIP 4-Warning [chars] Grp [dec] address [chars] is in the wrong subnet for this interface The GLBP virtual IP address contained in the Hello message cannot be learnt as it is not within a subnet configured on the interface. - "Check the configuration on all GLBP routers and ensure " "that the virtual IP address is within a configured subnet." GLBP-4-DIFFVIP1 4-Warning [chars] Grp [dec] active routers virtual IP address [chars] is different to the locally configured address [chars] The GLBP virtual IP address contained in the Hello message from the Active router is different to that configured locally. - "Check the configuration on all GLBP routers." GLBP-4-DUPADDR 4-Warning Duplicate address [chars] on [chars] sourced by [enet] The IP address in a GLBP message received on the interface is the same as the router's own IP address. This may be because of misconfiugration or because of a malfunctioning switch - "Check the configurations on all the GLBP routers and make sure that " "any switches you have are functioning properly." GLBP-4-DUPVIP1 4-Warning [chars] Grp [dec] address [chars] is already assigned to [chars] group [dec] The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to a different GLBP group. - "Check the configuration on all GLBP routers." GLBP-4-DUPVIP2 4-Warning [chars] Grp [dec] address [chars] is already assigned on this interface The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to this interface. - "Check the configuration on all GLBP routers." GLBP-4-DUPVIP3 4-Warning [chars] Grp [dec] address [chars] is already assigned to or overlaps with an address on another interface or application The GLBP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to or overlaps with an address on another interface or application. - "Check the configuration on all GLBP routers." GLBP-6-FWDSTATECHANGE 6-Information [chars] Grp [dec] Fwd [dec] state [chars] -> [chars] The GLBP forwarder has changed state - LOG_STD_NO_ACTION GLBP-6-STATECHANGE 6-Information [chars] Grp [dec] state [chars] -> [chars] The GLBP gateway has changed state - LOG_STD_NO_ACTION GMPLS_UNSUPPORTED_RESOURCE-3-MPLS_TE_LM 3-Error ERRMSG_NOFLAGS - - - GMPLS_UNSUPPORTED_RESOURCE-3-MPLS_TE_LM 3-Error ERRMSG_NOFLAGS - - - GPRSFLTMG-0-GPRS_DHCP 0-Emergency \ [chars] Two reasons for this error message\n\ 1. DHCP Client failed to get started this could be because of malloc\n\ failures.\n\ 2. GPRS DHCP Process failed to start gprs "If this error message is seen it is recommended not to use this \n\ GGSN for PDP session establishment with SGSN with dynamic IP request.\n\ Check the available memory in the box and for the first reason try \n\ to get 'debug dhcp detail' before the failure.\n\ Contact your technical support representative with the error \n\ message you got." GPRSFLTMG-0-GPRS_SERVICE 0-Emergency \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] You get this error messages because of one of the following reasons :\n\ 1. Path fail - No echo message is received from the GSN peer \n\ and time out. \n\ 3. GGSN service up - GGSN service starts.\n\ 4. GGSN service down - GGSN service shutdown.\n\ 5. Primary Charging Gateway down - Primary charging gateway is not \n\ reachable or unconfigured.\n\ 6. Primary Charging Gateway up - Primary Charging gateway is up or \n\ its configured .\n\ 7. Secondary Charging Gateway up - Secondary Charging Gateway is up \n\ or its configured.\n\ 8. Secondary Charging Gateway becomes unreachable or unconfigured. gprs "Error messages with reasons 36 and 7 are informational.\n\ For error messages with the other reasons contact your technical \n\ supportrepresentative with the error message you got." GPRSFLTMG-0-GTPv1NORESOURCE 0-Emergency \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] Available resources exhausted to continue GGSN service because of\n\ the following reasons :\n\ 1. Number of pending signaling messages reaches limit.\n\ 2. Out of Memory - Insuffient in GGSN.\n\ 3. System failure - Permenant system failure has occured. gprs "1. Check whether you can increase number of PDP that can be handled\n\ by GGSN.\n\ If the problem recurs contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show gprs gtp status'." GPRSFLTMG-0-NOPROCESS 0-Emergency \ [chars] A Process could not be started - "Please contact your technical support representative \n\ with the error message you got and with the output of \n\ 'show gprs gtp status'." GPRSFLTMG-0-RESOURCE 0-Emergency \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] Available resources exhausted to continue GGSN service because of \n\ the following reasons :\n\ 1. Number of PDP reaches Limit.\n\ 2. Number of Network Initiated PDP reached percentage - Insuffient \n\ in GGSN.\n\ 3. Number of IP PDP regenerated PPP reaches limit. gprs "1. Check whether you can increase number of PDP that can be handled \n\ by GGSN.\n\ If the problem recurs contact your technical support representative \n\ with the error message you got and with the output of \n\ 'show gprs gtp status'." GPRSFLTMG-4-AAAFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] A PDP Activation has been failed because of one of the \n\ following reasons: \n\\n\ 1. No RADIUS server present for Authentication - No RADIUS server is \n\ configured or configured RADIUS server is not reachable.\n\ 2. Authentication fail - Authentication failed for invalid username \n\ or password.\n\ 3. Missing PAP/CHAP in non-transparent mode - PAP/CHAP IE is missing in \n\ the packet in non-transparent mode.\n\ 4. Missing username - User name field is not present in the PDP \n\ activation Request sent. gprs "1. Check whether RADIUS server is configured properly and able to \n\ ping it.\n\ 2. Check whether RADIUS server is configured properly. \n\ For the other reasons copy and save the error message with the output \n\ of 'show running' command. and contact your technical support \n\ representative." GPRSFLTMG-4-APNRELATEDERROR_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] PDP activation has failed due to one of the APN related problem :\n\ 1. APN not configured - The APN requested in the PDP Request is not\n\ configured in the GGSN router.\n\ 2. Subscribe mode on APN but selection mode field not verified.\n\ 3. Duplicate static IP address to access same APN.\n\ 4. Session already exists for a different APN. gprs "Check the APN configuration correspondingly. If that can't solve the \n\ problem get the output of 'sh run' and 'sh gprs access-point all' \n\ copy the error message exactly as it appears and report to your \n\ technical support representative." GPRSFLTMG-4-CHARGING 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] You get this syslog message due to one of the following reasons :\n\ 1. Primary/Secondary Charging gateway configured/unconfigured.\n\ 2. GSN GTP' Transfer Failure - Failure in sending CDRs to \n\ Charging gateway configured.\n\ 3. GSN CGF Echo Request Failure/Restored - Failure/Success of \n\ Echo messages sent charging gateway to check the connectivity of \n\ the Charging gateway configured. \n\ 4. GSN CDR Capacity Full/Free - Status of GSN CDR buffer full/free \n\ the subsequent packet might be dropped if the buffer is full.\n\ 5. GSN CDR Discard Notification - a status whether the GSN CDRs are\n\ getting discard/buffered. gprs "1. This is informational .\n\ 2. Check whether the charging gateways are configured correctly \n\ and are active with the charging functionality. \n\ 3. If the configured charging gateway is up and reachable from the GSN \n\ check whether charging function is enabled in the gateway.\n\ 45. If you have configured "gprs char charging-send-buffer-size" with minimum bytes you may configure maximum bytes.\n\ \n\ If the problem recurs contact your technical support representative \n\ with the error message you got" GPRSFLTMG-4-GTPv1AAAFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] A PDP Activation has been failed because of one of the \n\ following reasons: \n\\n\ 1. No RADIUS server present for Authentication - No RADIUS server is \n\ configured or configured RADIUS server is not reachable.\n\ 2. Authentication fail - Authentication failed for invalid username \n\ or password.\n\ 3. Missing PAP/CHAP in non-transparent mode - PAP/CHAP IE is missing in \n\ the packet in non-transparent mode.\n\ 4. Missing username - User name field is not present in the PDP \n\ activation Request sent. gprs "1. Check whether RADIUS server is configured properly and able to \n\ ping it.\n\ 2. Check whether RADIUS server is configured properly. \n\ For the other reasons copy and save the error message with the output \n\ of 'show running' command. and contact your technical support \n\ representative." GPRSFLTMG-4-GTPv1APNRELATEDERROR_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] PDP activation has failed due to one of the APN related problem :\n\ 1. APN not configured - The APN requested in the PDP Request is not\n\ configured in the GGSN router.\n\ 2. Subscribe mode on APN but selection mode field not verified.\n\ 3. Duplicate static IP address to access same APN.\n\ 4. Session already exists for a different APN. gprs "Check the APN configuration correspondingly. If that can't solve the \n\ problem get the output of 'sh run' and 'sh gprs access-point all' \n\ copy the error message exactly as it appears and report to your \n\ technical support representative." GPRSFLTMG-4-GTPv1IPALLOCATIONFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] Failed to allocate IP address dynamically because of one of the \n\ following reason:\n\\n\ 1. a. DHCP/RADIUS server IP address has been wrongly configured in GGSN.\n\ b. DHCP/RADIUS server is reachable but the configuration to \n\ allocate IP address might be wrong. or \n\ c. Properly configured DHCP/RADIUS server is unreachable.\n\ 2. Dynamic IP allocation is disabled in the APN configuration .\n\ 3. Missing PAP/CHAP information from radius client in \n\ transparent mode - Username and Password is missing in the \n\ PDP Activation Request. gprs "1.a. Check whether the GGSN is conifugred with the valid DHCP/RADIUS \n\ server IP address.\n\ b. Check whether DHCP/RADIUS server is configured properly to \n\ allocate IP address .\n\ c. If the configurations are fine then check whether the server \n\ is reachable from GGSN.\n\ 2. Configure IP allocation pool as either DHCP proxy client or RADIUS \n\ client in the APN .\n\ If you could not solve the problem still contact your technical support\n\ representative with the error message you got." GPRSFLTMG-4-GTPv1MOBILITY 4-Warning GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] One of the following Mobility Related problem has occured :\n\ 1. MS GPRS Detached.\n\ 2. MS GPRS present.\n\ 3. MS not GPRS responding for network initiated PDP - MS does not \n\ respond for packets initiated by external network. \n\ 4. MS Refused for network initiated PDP.\n\ 5. IMSI unknown for network initiated PDP. gprs "If the problem recurs contact your technical support representative\n\ with the error message you got " GPRSFLTMG-4-GTPv1QOSFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [dec] [chars] QoS negotitaion/update has failed since resources not available. gprs "Contact your technical support representative with the error messages \n\ and the output of command 'sh gprs gtp status' ." GPRSFLTMG-4-IPALLOCATIONFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] Failed to allocate IP address dynamically because of one of the \n\ following reason:\n\\n\ 1. a. DHCP/RADIUS server IP address has been wrongly configured in GGSN.\n\ b. DHCP/RADIUS server is reachable but the configuration to \n\ allocate IP address might be wrong. or \n\ c. Properly configured DHCP/RADIUS server is unreachable.\n\ 2. Dynamic IP allocation is disabled in the APN configuration .\n\ 3. Missing PAP/CHAP information from radius client in \n\ transparent mode - Username and Password is missing in the \n\ PDP Activation Request. gprs "1.a. Check whether the GGSN is conifugred with the valid DHCP/RADIUS \n\ server IP address.\n\ b. Check whether DHCP/RADIUS server is configured properly to \n\ allocate IP address .\n\ c. If the configurations are fine then check whether the server \n\ is reachable from GGSN.\n\ 2. Configure IP allocation pool as either DHCP proxy client or RADIUS \n\ client in the APN .\n\ If you could not solve the problem still contact your technical support\n\ representative with the error message you got." GPRSFLTMG-4-MOBILITY 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Username: [chars] Reason: [dec] [chars] One of the following Mobility Related problem has occured :\n\ 1. MS GPRS Detached.\n\ 2. MS GPRS present.\n\ 3. MS not GPRS responding for network initiated PDP - MS does not \n\ respond for packets initiated by external network. \n\ 4. MS Refused for network initiated PDP.\n\ 5. IMSI unknown for network initiated PDP. gprs "If the problem recurs contact your technical support representative\n\ with the error message you got " GPRSFLTMG-4-QOSFAIL_PDPACTIVATIONFAIL 4-Warning \ GSN: [inet] TID: %08x%08x APN: [chars] Reason: [dec] [chars] QoS negotitaion/update has failed since resources not available. gprs "Contact your technical support representative with the error messages \n\ and the output of command 'sh gprs gtp status' ." GPS_DR-0-MODULE_FAIL_AUTHENTICATION 0-Emergency Failed to authenticate the GPS/DR module: [chars] return code 0x[hec]. Failed to authenticate the GPS/DR module. TAMPER_COMPONENT LOG_STD_ACTION GPS_DR-0-MODULE_FAIL_INIT 0-Emergency Failed to initialize the GPS/DR module. Failed to initialize the GPS/DR module. - LOG_STD_ACTION GR_IOS_DB-3-DB_EXIST 3-Error Persist DB [chars][dec] not deleted!!!\n GR_IOS_DB was not deleted from boot flash! - GR_IOS_DB_ERR_ACTION GR_IOS_DB-3-OPEN_DB 3-Error Failed to open path: [chars] handle: 0x[hec] err: [chars] [dec]\n Failed to open GR_IOS_DB database - GR_IOS_DB_ERR_ACTION GR_IOS_DB-3-PATH_FAILED 3-Error Failed to get database path for [chars]\n Failed to get database path. - GR_IOS_DB_ERR_ACTION GR_IOS_DB-3-VFT_SET 3-Error Failed to set VFT path: [chars] handle: 0x[hec] err: [chars] [dec]\n Failed to set VFT for GR_IOS_DB database - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-TOPO_DEL 3-Error Failed to delete Topology record 0x[hec] number: [dec] Failed to delete topology mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-TOPO_GET 3-Error Failed to get vrf_id: 0x[hec] afi: [dec] topology: [chars] topo_id: 0x[hec] err: [chars] [dec]\n Failed to get topology mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-TOPO_SET 3-Error Failed to set vrf_id: 0x[hec] afi: [dec] topology: [chars] topo_id: 0x[hec] err: [chars] [dec]\n Failed to set topology mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-TOPO_TBL_FREE 3-Error Failed to free topology table err: [chars] [dec]\n Failed to free topology mapping table. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-TOPO_TBL_OPEN 3-Error Failed to open table type: [dec] root: 0x[hec] err: [chars] [dec]\n Failed to open topology mapping table. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-VRF_DEL 3-Error Failed to delete VRF record 0x[hec] number: [dec] Failed to delete VRF mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-VRF_GET 3-Error Failed to get vrf_name: [chars] vrf_id: 0x[hec] err: [chars] [dec]\n Failed to get VRF mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-VRF_SET 3-Error Failed to set vrf_name: [chars] vrf_id: 0x[hec] err: [chars] [dec]\n Failed to set VRF mapping entry. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-VRF_TBL_FREE 3-Error Failed to free VRF table err: [chars] [dec]\n Failed to free VRF mapping table. - GR_IOS_DB_ERR_ACTION GR_VRF_TOPO-3-VRF_TBL_OPEN 3-Error Failed to open table type: [dec] root: 0x[hec] err: [chars] [dec]\n Failed to open VRF mapping table. - GR_IOS_DB_ERR_ACTION GR-5-LDP 5-Notice ERRMSG_NOFLAGS - - - GR-5-LDP 5-Notice ERRMSG_NOFLAGS - - - GRIP-2-BADROUTE 2-Critical Error [chars] route - null table A hardware or software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." GRIP-3-BADPATHS 3-Error Invalid number of paths [dec] for %q An internal inconsistency was detected in the XNS routing table\n\ structure. - "Note the parameters associated with this message and call your\n\ technical support representative for assistance." GROUP_POLICY-2-STEERING_ACE_FAILED 2-Critical Failed to [chars][chars] steering policy '[chars]' for SGT=[chars] due to ACE '[chars]' error. Download will be retried in 60 seconds An error occurred in the ACE while GPP attempted to acquire steering policy from the policy server. Retry will be attempted in 60 seconds - LOG_STD_ACTION GROUP_POLICY-2-STEERING_ACE_FAILED 2-Critical Failed to [chars][chars] steering policy '[chars]' for SGT=[chars] due to ACE '[chars]' error. Download will be retried in 60 seconds An error occurred in the ACE while GPP attempted to acquire steering policy from the policy server. Retry will be attempted in 60 seconds - LOG_STD_ACTION GROUP_POLICY-3-STEERING_INSTALL_FAILED 3-Error Failed to [chars][chars] steering policy [chars] for SGT=[chars] An error occurred while GPP attempted to acquire steering policy from the policy server. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_INSTALL_FAILED 3-Error Failed to [chars][chars] steering policy [chars] for SGT=[chars] An error occurred while GPP attempted to acquire steering policy from the policy server. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_PEER_DOWNLOAD_FAILED 3-Error Failed to download peer policy for [chars] An error occurred while GPP attempted to acquire peer policy from the policy server - LOG_STD_ACTION GROUP_POLICY-3-STEERING_PEER_DOWNLOAD_FAILED 3-Error Failed to download peer policy for [chars] An error occurred while GPP attempted to acquire peer policy from the policy server - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_DEL_FAILED 3-Error Failed to delete steering policy definition. Invalid steering policy [chars]. An error occurred while GPP attempted to delete steering policy info with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_DEL_FAILED 3-Error Failed to delete steering policy definition. Invalid steering policy [chars]. An error occurred while GPP attempted to delete steering policy info with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_INFO_STALE 3-Error Steering policy definition is not valid. An error occurred while GPP attempted to access steering policy definition with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_INFO_STALE 3-Error Steering policy definition is not valid. An error occurred while GPP attempted to access steering policy definition with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_LIST_STALE 3-Error Steering policy named list having policy definition is not valid. An error occurred while GPP attempted to access steering policy list with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_DEFN_LIST_STALE 3-Error Steering policy named list having policy definition is not valid. An error occurred while GPP attempted to access steering policy list with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_SERVER_ENCRYPT_FAILURE 3-Error GPP policy-server password encryption failed GPP policy-server password encryption failed - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_SERVER_ENCRYPT_FAILURE 3-Error GPP policy-server password encryption failed Whitelist pattern length cannot exceed 100 for DSA snooping. ios-scansafe "This message is for informational purposed only" GROUP_POLICY-3-STEERING_POLICY_SERVER_INVALID_CREDENTIALS 3-Error Invalid policy-server credentials have configured on device OR Server port number is incorrect GPP policy-server username or password are invalid - LOG_STD_ACTION GROUP_POLICY-3-STEERING_POLICY_SERVER_INVALID_CREDENTIALS 3-Error Invalid policy-server credentials have configured on device OR Server port number is incorrect GPP policy-server username or password are invalid - LOG_STD_ACTION GROUP_POLICY-3-STEERING_SESSION_UNINST_FAILED 3-Error Failed to detach session handle from steering policy list for sgt[chars] - - - GROUP_POLICY-3-STEERING_SESSION_UNINST_FAILED 3-Error Failed to detach session handle from steering policy list for sgt[chars] - - - GROUP_POLICY-3-STEERING_SGT_POLICY_STALE 3-Error Steering policy for sgt '[chars]' is not valid. An error occurred while GPP attempted to access sgt policy with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_SGT_POLICY_STALE 3-Error Steering policy for sgt '[chars]' is not valid. An error occurred while GPP attempted to access sgt policy with invalid handle. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_SM_FAILED 3-Error Failed to start the entry state machine to start policy acquisition for name[chars] - - - GROUP_POLICY-3-STEERING_SM_FAILED 3-Error Failed to start the entry state machine to start policy acquisition for name[chars] - - - GROUP_POLICY-3-STEERING_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while GPP is performing a sync to the Standby. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_SYNC_FAILED 3-Error Failed to send [chars] sync msg[chars] to Standby An error occcured while GPP is performing a sync to the Standby. - LOG_STD_ACTION GROUP_POLICY-3-STEERING_TREE_MAP_INSERT_FAILED 3-Error Failed to insert the entry info into tree map for name[chars] - - - GROUP_POLICY-3-STEERING_TREE_MAP_INSERT_FAILED 3-Error Failed to insert the entry info into tree map for name[chars] - - - GROUP_POLICY-6-STEERING_ATTACH_SUCCESS 6-Information Successfully attached steering policy to PDM for sgt[chars]:[chars] - - - GROUP_POLICY-6-STEERING_ATTACH_SUCCESS 6-Information Successfully attached steering policy to PDM for sgt[chars]:[chars] - - - GROUP_POLICY-6-STEERING_POLICY_DEFN_UPDATE 6-Information Steering policy definition[chars]-[chars] updated to new definition[chars]-[chars] - - - GROUP_POLICY-6-STEERING_POLICY_DEFN_UPDATE 6-Information Steering policy definition[chars]-[chars] updated to new definition[chars]-[chars] - - - GSMAMRNB_ENABLER-3-GSMAMRNB_LICENSE_EULA_NOT_ACCEPTED 3-Error \n********************************************************* \ \nWARNING: GSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack'\ \nand accept the EULA to activate the license. \ \n*********************************************************\n EULA is not accepted for the license ios-licensing-atg LOG_STD_ACTION GSMAMRNB_ENABLER-3-GSMAMRNB_LICENSE_EULA_NOT_ACCEPTED 3-Error \n********************************************************* \ \nWARNING: GSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack'\ \nand accept the EULA to activate the license. \ \n*********************************************************\n EULA is not accepted for the license ios-licensing-atg LOG_STD_ACTION GT64010-1-DMASTALL 1-Alert DMA interrupt stalled restarted engine [dec] The driver timed out waiting for completion of DMA task. \n\ The DMA engine has been restarted. - LOG_STD_RECUR_ACTION GT64010-3-DMA 3-Error Interrupt error c=[hex] m=[hex] rc=[hex] An unexpected interrupt was registered from a DMA \n\ engine that was not initialized by software. - LOG_STD_ACTION GT64010-3-NOCHANNEL 3-Error Referencing unused DMA channel [dec] An access to an uninitialized DMA engine was attempted. - LOG_STD_ACTION GT64010-3-TIMER 3-Error Interrupt error c=[hex] m=[hex] rc=[hex] An unexpected timer interrupt was received from\n\ a timer element that was not initialized by software. - LOG_STD_ACTION GT64010-3-TIMERINSTALL 3-Error Attempt to install already installed timer [dec] An attempt was made to initialize a timer element that\n\ is already in use. - LOG_STD_ACTION GTP_AIC-3-CHUNK_CREATE_FAIL 3-Error - This message indicates that the packet is dropped by GTP AIC. cpp-ucode "This message is for informational purposed only but may indicate " "a security problem." GTP-0-GTPv1PACKETPARSINGERROR 0-Emergency \ GSN: [inet] TEID: [hec] APN: [chars] Reason: [chars] A PDP context activation failed at the packet parsing state for one\n\ of the following reasons:\n\ 1. Mandatory IE is missing in the PDP .\n\ 2. Mandatory IE incorrect - Mandatory IE has invalid range of value.\n\ 3. Mandatory IE out of sequence - The Mandatory IEs are not in sequence.\n\ 4. Invalid message format.\n\ 5. Optional IE incorrect - Optional IE present in the packet has\n\ invalid range of value.\n\ 6. Version not support - The GGSN Node does not support the GTP\n\ version recieved.\n\ 7. Non-charging msg in charging path.\n\ 8. Charging msg in GTP path.\n\ 9. Unknown GTP message.\n\ 10.Message too short - GTP message received is too short to contain\n\ all expected inform IE.\n\ 11.Unexpected message seen. gprs "Copy the error message exactly as it appears and report to your\n\ technical support representative." GTP-0-NORESOURCE 0-Emergency \ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars] Available resources exhausted to continue GGSN service because of\n\ the following reasons :\n\ 1. Number of pending signaling messages reaches limit.\n\ 2. Out of Memory - Insuffient in GGSN.\n\ 3. System failure - Permenant system failure has occured. gprs "1. Check whether you can increase number of PDP that can be handled\n\ by GGSN.\n\ If the problem recurs contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show gprs gtp status'." GTP-0-PACKETPARSINGERROR 0-Emergency \ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars] A PDP context activation failed at the packet parsing state for one\n\ of the following reasons:\n\ 1. Mandatory IE is missing in the PDP .\n\ 2. Mandatory IE incorrect - Mandatory IE has invalid range of value.\n\ 3. Mandatory IE out of sequence - The Mandatory IEs are not in sequence.\n\ 4. Invalid message format.\n\ 5. Optional IE incorrect - Optional IE present in the packet has\n\ invalid range of value.\n\ 6. Version not support - The GGSN Node does not support the GTP\n\ version recieved.\n\ 7. Non-charging msg in charging path.\n\ 8. Charging msg in GTP path.\n\ 9. Unknown GTP message.\n\ 10.Message too short - GTP message received is too short to contain\n\ all expected inform IE.\n\ 11.Unexpected message seen. gprs "Copy the error message exactly as it appears and report to your\n\ technical support representative." GTP-2-GSNSERVICEUPDOWN 2-Critical GSN service [chars] changed state to [chars] SGSN service starts or shutdown gprs "If this message recurs contact your technical support representative." GTP-2-GTPv1PDPACTIVATIONFAIL 2-Critical GTP PDP activation/update failed GSN: [inet] TEID: [hec] Reason: [chars] A PDP context activation failed gprs "If this message recurs contact your technical support representative." GTP-2-PDPACTIVATIONFAIL 2-Critical GTP PDP activation/update failed GSN: [inet] TID: [hec][hec] Reason: [chars] A PDP context activation failed gprs "If this message recurs contact your technical support representative." GTP-3-INCOMPLETECONFIG 3-Error \ APN: [chars] Reason: [chars] A required configuration is missing gprs "Please make sure the missing commands are configured" GTP-4-RECOVERYIEDIFF 4-Warning \ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars] GGSN has recieved PDP update request with different Recovery\n\ Information Element in the same path. gprs "Contact your technical support representative with the error messages\n\ you got." GTP-6-PDP_PURGED 6-Information \ GSN: [inet] TID: [hec][hec] APN: [chars] Reason: [chars] PDP context purged because of PDP context idle timeout - "This is purely informational " GULF2488-3-INITERR 3-Error gulf2488 chip initialization failed errcode=[dec]: [chars] required resources unavailable. osm-choc-ds3 "Reinsert the linecard. If still fails do\n\ 'test cwtlc show seeprom red' swap hardware and\n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative." GULF2488-3-PROVERR 3-Error gulf2488 channel provisioning failed slice:[dec] ch:[dec]: [chars] required resources unavailable. osm-choc-ds3 LOG_STD_ACTION GULF2488-3-UNPROVERR 3-Error gulf2488 channel unprovisioning failed slice:[dec] ch:[dec]: [chars] required resources unavailable. osm-choc-ds3 LOG_STD_ACTION GVRP-3-ADD_REGISTRY_FAILED 3-Error GVRP subsystem fails to add callback function [chars] Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose. gvrp LOG_STD_NO_ACTION GVRP-3-ENABLE_FAILED 3-Error GVRP can't be enabled because [chars] GVRP can't be enabled for some reason. gvrp "Action may be taken according to the given " "reason. If for instance the problem is " "due to lack of memory the user should " "add more memory to his system." GVRP-3-HA_INIT_FAILED 3-Error GVRP High Availability subsystem fails to be initialized and hence GVRP won't support HA stateful switchover. Either GVRP CF client or GVRP RF client fails to be initialized. gvrp "Enter the " "show redundancy clients " "and show checkpoint clients to " "find out which client is not initialized." GVRP-3-SUBSYS_INIT_FAILED 3-Error GVRP subsystem failed in initialization[chars] and GVRP won't This is extremely unlikely to occur on a customer device. If it does occur the cause is most likely due to the lack of memory so the software failed to create data structures. User should see many gvrp "Most likely the system has crashed by then " "if the problem is due to lack of memory. " "If the system miraculously came up then" "user can run show memory summary" " to check the memory usage. " "Please contact the TAC with the output of " "show memory summary " "show version and " "show run and the " "associated syslog messages from the time " "of the problem." GVRP-6-MODECHANGE 6-Information The operating mode is changed to [chars] mode on interface [chars]. As a result of protocol negotiation the operating mode changed to the specified mode on the specified interface. gvrp LOG_STD_NO_ACTION H323_ALG-3-CHUNK_CREATE_FAIL 3-Error - Chunk create failed. H323 ALG will not be able to finish initialization. cpp-ucode LOG_STD_ACTION H323_ALG-3-CHUNK_MEM_LEAK 3-Error - Chunk memory is not being freed by H.323 ALG. cpp-ucode LOG_STD_ACTION HA_CLIENT-3-BS_TO_STBY_FAILED 3-Error The [chars] HA client's Bulk Sync phase was unsuccessful The nominated HA client could not get a buffer from the Checkpointing Facility CF in which to put some checkpointing as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-CF_REG_FAILED 3-Error CF registration for the [chars] HA client failed with return code [dec] The specified HA client failed to register properly with the Checkpointing Facility CF. This should not happen and suggests as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-CLIENT_INIT_FAILED 3-Error Initialisation of the [chars] HA client failed required fields missing The HA client utilities code could not initialise the specified client because some fields required by the utilities code were not provided by the client. This should not happen and suggests a software problem. as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-CP_TO_STBY_FAILED 3-Error Delivery of a checkpointing CP message from the [chars] HA client failed The nominated HA client on the Active unit was told by the Checkpointing Facility CF that one of its checkpointing messages as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-IF_INDEX_ADD_FAILURE 3-Error Unable to add an interface index to a table: [chars] rc=[dec] The interface index could not be added to a table. This should not normally happen and should be reported. as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-NO_BS_PROCESS 3-Error The [chars] HA client failed to create a Bulk Sync process rc [dec] The nominated HA client could not create an IOS process that it needed in order to perform its Bulk Sync. This means the client's Bulk Sync did not occur. Hence the Standby unit is now out-of-sync. This should not occur and should be reported. as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-NO_RF_BUFFER 3-Error The [chars] HA client failed to get a buffer len=[dec] from RF - - - HA_CLIENT-3-PROTO_VER_INCOMPAT 3-Error The HA client '[chars]' is incompatible with the peer The named HA client can not communicate with the client on the peer unit. These units can not be used in a warm or hot standby environment. as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-RF_MSG_NOT_SENT 3-Error Delivery of an RF message from the [chars] HA client failed rc=[dec] The nominated HA client was told by the Redundancy Facility RF as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-RF_REG_FAILED 3-Error RF registration for the [chars] HA client failed with return code [dec] The specified HA client failed to register properly with the Redundancy Facility RF. This should not happen and suggests as5850-redundancy LOG_STD_ACTION HA_CLIENT-3-VALIDITY_CHECK_FAILURE 3-Error The HA client detected a validity check failure: [chars] The HA client performed a validity check. This check failed and may indicate a serious problem. A reload may be required to recover from this situation as5850-redundancy LOG_STD_ACTION HA_CLIENT-4-CF_NOT_BUNDLED 4-Warning CF failed to go into bundled mode for the [chars] HA client rc [dec] The Checkpointing Facility CF did not allow the specified HA as5850-redundancy LOG_STD_ACTION HA_CLIENT-4-IF_INDEX_LOOKUP_FAILURE 4-Warning Unable to find an interface index: rc=[dec] [chars] The interface index could not be found. This is a rare but possible situation and it should be able to correct itself. as5850-redundancy LOG_STD_NO_ACTION HA_CLIENT-4-RESOURCE_RECOVERY_LIST_FAILURE 4-Warning Failed to create [chars] resource recovery list The specified resource recovery list could not be created. This means resource recovery cannot be performed upon switchover which will most likely leave some of the relevant resources unusable. This should not normally happen and should be reported. as5850-redundancy LOG_STD_ACTION HA_CONFIG_SYNC-3-BOOTVAR 3-Error Cannot communicate boot variable to standby [chars] Active failed to send the boot variable specified to standby. A reload or a switchover operation will likely result in the standby booting a wrong image. config-sync LOG_STD_ACTION HA_CONFIG_SYNC-3-BOOTVAR 3-Error Cannot communicate boot variable to standby [chars] Active failed to send the boot variable specified to standby. A reload or a switchover operation will likely result in the standby booting a wrong image. config-sync LOG_STD_ACTION HA_CONFIG_SYNC -3-BULK_CFGSYNC 3-Error [chars] Bulk config sync failure the reason for the failure will be provided in the string config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-BULK_CFGSYNC 3-Error [chars] Bulk config sync failure the reason for the failure will be provided in the string config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC-3-CONFREG 3-Error Cannot communicate config register to standby Active failed to send the config register to standby. The active and standby supervisors won't have the same config registers. config-sync LOG_STD_ACTION HA_CONFIG_SYNC-3-CONFREG 3-Error Cannot communicate config register to standby Active failed to send the config register to standby. The active and standby supervisors won't have the same config registers. config-sync LOG_STD_ACTION HA_CONFIG_SYNC -3-FS_BULK_CFGSYNC 3-Error [chars] [[chars]] Bulk config sync filesys failure the reason for the failure will be provided in the string config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-FS_BULK_CFGSYNC 3-Error [chars] [[chars]] Bulk config sync filesys failure the reason for the failure will be provided in the string config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-GENERAL 3-Error [chars] General Config Sync Problem config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-GENERAL 3-Error [chars] General Config Sync Problem config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-IPC 3-Error IPC operation failed for [ [chars] ] with error code [ [chars] ] A config sync error occurred. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-IPC 3-Error IPC operation failed for [ [chars] ] with error code [ [chars] ] A config sync error occurred. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_MTU 3-Error CONFIG SYNC Failed to get MTU Size for session[[dec]] msg_type[[dec]] MTU[[dec]] rc[[dec]] An ISSU Config Sync failed to get Messge MTU. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_MTU 3-Error CONFIG SYNC Failed to get MTU Size for session[[dec]] msg_type[[dec]] MTU[[dec]] rc[[dec]] An ISSU Config Sync failed to get Messge MTU. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_REG 3-Error [chars] with error code [ [chars] ] An ISSU Config Sync Registration Error occurred. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_REG 3-Error [chars] with error code [ [chars] ] An ISSU Config Sync Registration Error occurred. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_XFORM 3-Error CONFIG SYNC [chars] msg_type[[dec]] rc[[dec]] An ISSU Config Sync failed to transform messge. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-ISSU_XFORM 3-Error CONFIG SYNC [chars] msg_type[[dec]] rc[[dec]] An ISSU Config Sync failed to transform messge. The details about\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-LBL_CFGSYNC 3-Error [chars] Line by Line sync failure what was attempted and what went wrong \n\ will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-LBL_CFGSYNC 3-Error [chars] Line by Line sync failure what was attempted and what went wrong \n\ will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-LBL_POLICY 3-Error [chars] Active and Standby configuration out of sync LBL\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -3-LBL_POLICY 3-Error [chars] Active and Standby configuration out of sync LBL\n\ what was attempted and what went wrong will be printed. config-sync "Copy the error message exactly as it appears. Copy down the system's\n\ configuration along with any other relevant information. Contact your\n\ technical support representative for assistance." HA_CONFIG_SYNC -6-BULK_CFGSYNC_SUCCEED 6-Information Bulk Sync succeeded Bulk Sync has succeeded config-sync "No action necessary" HA_CONFIG_SYNC -6-BULK_CFGSYNC_SUCCEED 6-Information Bulk Sync succeeded Bulk Sync has succeeded config-sync "No action necessary" HA_CONFIG_SYNC -6-LBL_PRC_SUBCODE 6-Information CONFIG SYNC : Subcode not matching for command [chars] Active subcode[0x[hec]] Standby subcode[0x[hec]] The line by line synchronization of a command has succeeded. A command entered on the active system was successfully synchronized with the standby system. However the sub code of Parser Return Code that were returned by the Active and Standby systems were different. However the sub code of Parser Return Code that were returned by the Active and Standby systems where different. config-sync "Normally no action is required. If however any " "problems with line by line synchronization are found " "copy this message exactly as it appears on the console " "or in the system log and contact your Cisco technical " "support representative." HA_CONFIG_SYNC -6-LBL_PRC_SUBCODE 6-Information CONFIG SYNC : Subcode not matching for command [chars] Active subcode[0x[hec]] Standby subcode[0x[hec]] The line by line synchronization of a command has succeeded. A command entered on the active system was successfully synchronized with the standby system. However the sub code of Parser Return Code that were returned by the Active and Standby systems were different. However the sub code of Parser Return Code that were returned by the Active and Standby systems where different. config-sync "Normally no action is required. If however any " "problems with line by line synchronization are found " "copy this message exactly as it appears on the console " "or in the system log and contact your Cisco technical " "support representative." HA_EM-3-ACTION_CNS_OPEN_FAIL 3-Error [chars]: Unable to open connection to CNS Event Agent: [dec] The CNS Action process failed to open CNS handle to Event Agent. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-ACTION_CNS_OPEN_FAIL 3-Error [chars]: Unable to open connection to CNS Event Agent: [dec] The CNS Action process failed to open CNS handle to Event Agent. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMC_CBH_PROCESS_CREATE 3-Error [chars]: callback handler process create failed for eid: [dec] The process_create function reported an error trying to create the callback handler process. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMC_CBH_PROCESS_CREATE 3-Error [chars]: callback handler process create failed for eid: [dec] The process_create function reported an error trying to create the callback handler process. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMC_FH_INIT 3-Error [chars]: fh_init failed : [dec] The strdup function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMC_FH_INIT 3-Error [chars]: fh_init failed : [dec] The strdup function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_EMPTY_QUEUE 3-Error [chars]: The [chars] event detector I/O queue empty. The SNMP message failed to be created ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_EMPTY_QUEUE 3-Error [chars]: The [chars] event detector I/O queue empty. The SNMP message failed to be created ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_OID_UNAVAIL 3-Error [chars]: The following oid has become unavailable: [chars] The enqueue function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_OID_UNAVAIL 3-Error [chars]: The following oid has become unavailable: [chars] The enqueue function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_SNMP_MIB_OBJ_REP_FAIL 3-Error [chars]: SNMP MIB object info replace failed [dec] The SNMP MIB object info replace function has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_SNMP_MIB_OBJ_REP_FAIL 3-Error [chars]: SNMP MIB object info replace failed [dec] The SNMP MIB object info replace function has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_SNMP_OBJECT_UNKNOWN_RESPONSE_CODE 3-Error [chars]: Unknown SNMP object response code [dec] The SNMP MIB object response code is unknown. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_SNMP_OBJECT_UNKNOWN_RESPONSE_CODE 3-Error [chars]: Unknown SNMP object response code [dec] The SNMP MIB object response code is unknown. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_TTY_NUM 3-Error [chars]: Error occurred while fetching TTY number. The Embedded Event Manager failed to fetch a TTY number. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMFD_TTY_NUM 3-Error [chars]: Error occurred while fetching TTY number. The Embedded Event Manager failed to fetch a TTY number. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_ACTION 3-Error [chars]: Error occurred while performing action: [chars]. The Embedded Event Manager Policy Director failed to perform an action for the registered event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_ACTION 3-Error [chars]: Error occurred while performing action: [chars]. The Embedded Event Manager Policy Director failed to perform an action for the registered event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_ACTION_INFO 3-Error [chars]: Error occurred while fetching action information: [dec]. The Embedded Event Manager applet attempted to set the state of a tracking object that does not exist. ha/eem "Only set the state of tracking objects that have already been " "configured in the system. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_ACTION_INFO 3-Error [chars]: Error occurred while fetching action information: [dec]. The Embedded Event Manager applet attempted to set the state of a tracking object that does not exist. ha/eem "Only set the state of tracking objects that have already been " "configured in the system. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_CHECKSUM_MISMATCH 3-Error [chars]: file checksum mismatch The checksum value of an installed policy does not match the value provided by the installation manager. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_CHECKSUM_MISMATCH 3-Error [chars]: file checksum mismatch The checksum value of an installed policy does not match the value provided by the installation manager. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_CLI_CONNECT 3-Error Unable to establish CLI session: [chars] Unable to establish CLI session. ha/eem "" HA_EM-3-FMPD_CLI_CONNECT 3-Error Unable to establish CLI session: [chars] Unable to establish CLI session. ha/eem "" HA_EM-3-FMPD_CLI_DISCONNECT 3-Error Error disconnecting from CLI session: [chars] An error occurred while disconnecting from the CLI session. ha/eem "" HA_EM-3-FMPD_CLI_DISCONNECT 3-Error Error disconnecting from CLI session: [chars] An error occurred while disconnecting from the CLI session. ha/eem "" HA_EM-3-FMPD_CLI_NOTTY 3-Error Error attempting to access an unopened CLI session: [chars] An error occurred attempting to access an unopened CLI session: [chars] ha/eem "" HA_EM-3-FMPD_CLI_NOTTY 3-Error Error attempting to access an unopened CLI session: [chars] An error occurred attempting to access an unopened CLI session: [chars] ha/eem "" HA_EM-3-FMPD_CLI_READ 3-Error Unable to read CLI response: [chars] Unable to read CLI response. ha/eem "" HA_EM-3-FMPD_CLI_READ 3-Error Unable to read CLI response: [chars] Unable to read CLI response. ha/eem "" HA_EM-3-FMPD_CLI_WRITE 3-Error Unable to send CLI command: [chars] Unable to send CLI command. ha/eem "" HA_EM-3-FMPD_CLI_WRITE 3-Error Unable to send CLI command: [chars] Unable to send CLI command. ha/eem "" HA_EM-3-FMPD_ERROR 3-Error Error executing applet [chars] statement [chars] The Embedded Event Manager policy director found an error when processing an applet. ha/eem "Check syntax of applet statement. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_ERROR 3-Error Error executing applet [chars] statement [chars] The Embedded Event Manager policy director found an error when processing an applet. ha/eem "Check syntax of applet statement. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_EXECUTE_CALLBACK 3-Error [chars]: failed to execute callback Failed to execute callback routine. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_EXECUTE_CALLBACK 3-Error [chars]: failed to execute callback Failed to execute callback routine. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_FH_INIT 3-Error [chars]: could not initialize Embedded Event Manager service: [chars] An internal error was detected when initializing Embedded Event Manager service. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_FH_INIT 3-Error [chars]: could not initialize Embedded Event Manager service: [chars] An internal error was detected when initializing Embedded Event Manager service. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_CREATE 3-Error [chars]: failed to create an IPC port: [chars] Embedded Event Manager failed to create an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_CREATE 3-Error [chars]: failed to create an IPC port: [chars] Embedded Event Manager failed to create an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_OPEN 3-Error [chars]: failed to open an IPC port: [chars] Embedded Event Manager failed to open an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_OPEN 3-Error [chars]: failed to open an IPC port: [chars] Embedded Event Manager failed to open an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_REGISTER 3-Error [chars]: failed to register an IPC port: [chars] Embedded Event Manager failed to register an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_IPC_PORT_REGISTER 3-Error [chars]: failed to register an IPC port: [chars] Embedded Event Manager failed to register an IPC port. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NO_PROC 3-Error [chars]: Failed to create process The process create function reports an error ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NO_PROC 3-Error [chars]: Failed to create process The process create function reports an error ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NOEID 3-Error [chars]: No such event id found. An internal software error occurred. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NOEID 3-Error [chars]: No such event id found. An internal software error occurred. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NOESID 3-Error [chars]: No such event spec id found. The Embedded Event Manager Policy Director could not find the event for the event spec. ID. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_NOESID 3-Error [chars]: No such event spec id found. The Embedded Event Manager Policy Director could not find the event for the event spec. ID. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_PROCESS_XML 3-Error [chars]: error processing xml buffer An error occurred processing the event publish information xml buffer. ha/eem "Copy the message exactly as it appears and report it your technical\n\ support representative." HA_EM-3-FMPD_PROCESS_XML 3-Error [chars]: error processing xml buffer An error occurred processing the event publish information xml buffer. ha/eem "Copy the message exactly as it appears and report it your technical\n\ support representative." HA_EM-3-FMPD_QUEUE_INIT 3-Error [chars]: could not initialize queue An internal error was detected when initializing Embedded Event Manager queue. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_QUEUE_INIT 3-Error [chars]: could not initialize queue An internal error was detected when initializing Embedded Event Manager queue. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_REQINFO 3-Error [chars]: Error attempting to fetch event information: [chars]. The Embedded Event Manager Policy Director failed to receive event info for a callback. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_REQINFO 3-Error [chars]: Error attempting to fetch event information: [chars]. The Embedded Event Manager Policy Director failed to receive event info for a callback. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_SET_INFO 3-Error [chars]: Error occurred while fetching variable information: [dec]. The Embedded Event Manager Policy Director was unable to set the variable with the requested information. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_SET_INFO 3-Error [chars]: Error occurred while fetching variable information: [dec]. The Embedded Event Manager Policy Director was unable to set the variable with the requested information. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_SMTP 3-Error Error occurred when sending mail to SMTP server: [chars] : [chars] An unexpected error occurred when sending mail to SMTP server. ha/eem "" HA_EM-3-FMPD_SMTP 3-Error Error occurred when sending mail to SMTP server: [chars] : [chars] An unexpected error occurred when sending mail to SMTP server. ha/eem "" HA_EM-3-FMPD_SMTP_SEND 3-Error Unable to send notification using all SMTP servers An unexpected error occurred when sending mail to all SMTP servers. ha/eem "" HA_EM-3-FMPD_SMTP_SEND 3-Error Unable to send notification using all SMTP servers An unexpected error occurred when sending mail to all SMTP servers. ha/eem "" HA_EM-3-FMPD_UNKNOWN_ENV 3-Error [chars]: could not find environment variable: [chars] The Embedded Event Manager policy director could not find the environment variable specified in the action message. ha/eem "Only use well known Embedded Event Manager environment variables. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_UNKNOWN_ENV 3-Error [chars]: could not find environment variable: [chars] The Embedded Event Manager policy director could not find the environment variable specified in the action message. ha/eem "Only use well known Embedded Event Manager environment variables. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-3-FMPD_UNKNOWNTYPE 3-Error [chars]: Unknown event type found in applet. The Embedded Event Manager applet had an unknown event type. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_UNKNOWNTYPE 3-Error [chars]: Unknown event type found in applet. The Embedded Event Manager applet had an unknown event type. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_WRONGTYPE 3-Error [chars]: Published event type does not match event spec. The Embedded Event Manager Policy Director detected a mis-match in event type between the published event and the event spec. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMPD_WRONGTYPE 3-Error [chars]: Published event type does not match event spec. The Embedded Event Manager Policy Director detected a mis-match in event type between the published event and the event spec. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_CNS_FAIL 3-Error [chars]: Failed to perform CNS action: [chars] The Embedded Event Manager failed attempting to send a CNS message. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_CNS_FAIL 3-Error [chars]: Failed to perform CNS action: [chars] The Embedded Event Manager failed attempting to send a CNS message. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_EMPTY_QUEUE 3-Error [chars]: The I/O queue empty. The I/O queue is empty at this point and should not be. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_EMPTY_QUEUE 3-Error [chars]: The I/O queue empty. The I/O queue is empty at this point and should not be. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_ENQUEUE_FAIL 3-Error [chars]: The Unable to enqueue packet onto queue. The queue is not in a state to handle enqueues. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_ENQUEUE_FAIL 3-Error [chars]: The Unable to enqueue packet onto queue. The queue is not in a state to handle enqueues. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_NO_TRACK 3-Error Use of the \track\ keyword in the correlate statement is not supported in this image. The Embedded Event Manager Track ED is not supported in this image. ha/eem "Track ED is not available in this image" HA_EM-3-FMS_NO_TRACK 3-Error Use of the \track\ keyword in the correlate statement is not supported in this image. The Embedded Event Manager Track ED is not supported in this image. ha/eem "Track ED is not available in this image" HA_EM-3-FMS_POLICY_CHECKSUM 3-Error [chars]: Checksum error for policy [chars] - this policy will not be run The checksum computed for the specified policy does not match the original checksum computed when the policy was registered. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_POLICY_CHECKSUM 3-Error [chars]: Checksum error for policy [chars] - this policy will not be run The checksum computed for the specified policy does not match the original checksum computed when the policy was registered. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_POLICY_LOOKUP_FAIL 3-Error [chars]: Failed to look up in the table the registration specification for policy [chars]. The realloc function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_POLICY_LOOKUP_FAIL 3-Error [chars]: Failed to look up in the table the registration specification for policy [chars]. The realloc function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_QUEUE_INIT 3-Error [chars]: The Unable to initialize queue. An attempt to publish an event failed because there is no more room in the publish queue. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_QUEUE_INIT 3-Error [chars]: The Unable to initialize queue. An attempt to publish an event failed because there is no more room in the publish queue. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-3-FMS_SWITCH_NOT_RF_ACTIVE 3-Error [chars]: This processor is not in ACTIVE state state = [dec]. Switchover must be performed on ACTIVE processor. Switchovers must occur on ACTIVE unit not STANDBY unit. ha/eem "" HA_EM-3-FMS_SWITCH_NOT_RF_ACTIVE 3-Error [chars]: This processor is not in ACTIVE state state = [dec]. Switchover must be performed on ACTIVE processor. Switchovers must occur on ACTIVE unit not STANDBY unit. ha/eem "" HA_EM-4-FMFD_SNMP_NO_OBJECT_VALUE 4-Warning [chars]: SNMP MIB object value not provided The SNMP MIB object value is not provided for substitution. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMFD_SNMP_NO_OBJECT_VALUE 4-Warning [chars]: SNMP MIB object value not provided The SNMP MIB object value is not provided for substitution. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_DSIG_TYPE_CHANGE 4-Warning Cisco Signature not found or invalid. [chars] has been registered as a user policy. Cisco Signature not found or invalid. ha/eem "Sign with Cisco signature." HA_EM-4-FMPD_DSIG_TYPE_CHANGE 4-Warning Cisco Signature not found or invalid. [chars] has been registered as a user policy. Cisco Signature not found or invalid. ha/eem "Sign with Cisco signature." HA_EM-4-FMPD_EVENT_CREATE 4-Warning [chars]: failed to create an event: [chars] Failed to create an Embedded Event Manager event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_EVENT_CREATE 4-Warning [chars]: failed to create an event: [chars] Failed to create an Embedded Event Manager event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_EVENT_REG 4-Warning [chars]: failed to register an event: [chars] Failed to register an Embedded Event Manager event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_EVENT_REG 4-Warning [chars]: failed to register an event: [chars] Failed to register an Embedded Event Manager event. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_IPC_GET_PAK 4-Warning [chars]: failed to allocate an IPC buffer Embedded Event Manager failed to allocate a buffer from IPC. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_IPC_GET_PAK 4-Warning [chars]: failed to allocate an IPC buffer Embedded Event Manager failed to allocate a buffer from IPC. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_IPC_SEND_MSG 4-Warning [chars]: failed to send an IPC message: [chars] Embedded Event Manager failed to send a message through IPC. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_IPC_SEND_MSG 4-Warning [chars]: failed to send an IPC message: [chars] Embedded Event Manager failed to send a message through IPC. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-4-FMPD_NO_ACTION 4-Warning No action configured for applet [chars] No action has been configured for this applet. ha/eem "Configure at least one action for this applet." HA_EM-4-FMPD_NO_ACTION 4-Warning No action configured for applet [chars] No action has been configured for this applet. ha/eem "Configure at least one action for this applet." HA_EM-4-FMPD_NO_EVENT 4-Warning No event configured for applet [chars] No event has been configured for this applet. ha/eem "Configure an event for this applet." HA_EM-4-FMPD_NO_EVENT 4-Warning No event configured for applet [chars] No event has been configured for this applet. ha/eem "Configure an event for this applet." HA_EM-4-FMPD_NOTAGNAME 4-Warning [chars]: No tag [chars] found corresponding to this event publish. The Embedded Event Manager policy director could not associate the tagname with a published event. ha/eem "Only use tagnames in the action info type event reqinfo command which correspond to the published event." HA_EM-4-FMPD_NOTAGNAME 4-Warning [chars]: No tag [chars] found corresponding to this event publish. The Embedded Event Manager policy director could not associate the tagname with a published event. ha/eem "Only use tagnames in the action info type event reqinfo command which correspond to the published event." HA_EM-4-FMS_NO_SCHED_THREAD 4-Warning No threads are configured to service event class [chars] The Embedded Event Manager has no scheduler threads to service this event class. ha/eem "Configure threads for the event class using the 'event manager scheduler' command." HA_EM-4-FMS_NO_SCHED_THREAD 4-Warning No threads are configured to service event class [chars] The Embedded Event Manager has no scheduler threads to service this event class. ha/eem "Configure threads for the event class using the 'event manager scheduler' command." HA_EM-6-FMPD_CONTEXT_RETRIEVE 6-Information Failed to retrieve context for key [chars]: [chars] Failed to context retrieve variable information for event. ha/eem "Ensure context information with the given key is saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_CONTEXT_RETRIEVE 6-Information Failed to retrieve context for key [chars]: [chars] Failed to context retrieve variable information for event. ha/eem "Ensure context information with the given key is saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_CONTEXT_SAVE 6-Information Failed to save variable context for key [chars]: [chars] Failed to context save variable information for event. ha/eem "Ensure context information with the same key is not already saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_CONTEXT_SAVE 6-Information Failed to save variable context for key [chars]: [chars] Failed to context save variable information for event. ha/eem "Ensure context information with the same key is not already saved. " "If the message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_DIVIDE_ZERO 6-Information Invalid operand in arithmetic division cannot divide by zero Arithmetic division does not allow divide by zero. ha/eem "Ensure denominator provided to division action is non-zero." HA_EM-6-FMPD_DIVIDE_ZERO 6-Information Invalid operand in arithmetic division cannot divide by zero Arithmetic division does not allow divide by zero. ha/eem "Ensure denominator provided to division action is non-zero." HA_EM-6-FMPD_EEM_CONFIG 6-Information [chars]: [chars] The Embedded Event Manager reports an error on Event Manager configuration ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_EEM_CONFIG 6-Information [chars]: [chars] The Embedded Event Manager reports an error on Event Manager configuration ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_OPERAND_INVALID 6-Information Invalid operand in action expected value within range %ld to %ld received: [chars] Arithmetic actions only accept valid long integer values. ha/eem "Ensure value provided to action is long integer." HA_EM-6-FMPD_OPERAND_INVALID 6-Information Invalid operand in action expected value within range %ld to %ld received: [chars] Arithmetic actions only accept valid long integer values. ha/eem "Ensure value provided to action is long integer." HA_EM-6-FMPD_REGCOMP 6-Information Error compiling regular expression: [chars] An error was encountered when compiling the given regular expression. ha/eem "Check syntax of regular expression pattern. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_REGCOMP 6-Information Error compiling regular expression: [chars] An error was encountered when compiling the given regular expression. ha/eem "Check syntax of regular expression pattern. If the " "message continues to occur copy the message exactly as it appears " "and report it your technical support representative." HA_EM-6-FMPD_SNMP_DUP_OID 6-Information [chars]: duplicate oid The oid is a duplicate ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_DUP_OID 6-Information [chars]: duplicate oid The oid is a duplicate ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_NO_VAR 6-Information [chars]: No variable [chars] The variable is not defined. ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_NO_VAR 6-Information [chars]: No variable [chars] The variable is not defined. ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_TRAPVAR_ADD 6-Information [chars]: Error adding trapvar to queue [chars] The trap variable was not added to the queue. ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_TRAPVAR_ADD 6-Information [chars]: Error adding trapvar to queue [chars] The trap variable was not added to the queue. ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_VARS_EXCEEDED 6-Information [chars]: number of values exceeded [dec] The number of values per variable exceeded the maximum ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SNMP_VARS_EXCEEDED 6-Information [chars]: number of values exceeded [dec] The number of values per variable exceeded the maximum ha/eem "Check the EEM applet or policy configuration" HA_EM-6-FMPD_SWITCH_HARDWARE 6-Information [chars]: Policy has requested a hardware switchover An Embedded Event Manager policy requested that a hardware switchover occur. ha/eem "None" HA_EM-6-FMPD_SWITCH_HARDWARE 6-Information [chars]: Policy has requested a hardware switchover An Embedded Event Manager policy requested that a hardware switchover occur. ha/eem "None" HA_EM-6-FMPD_UPDATE_POLICY_COPY 6-Information Policy update has copied [dec] bytes from [chars] to [chars] An EEM policy has been copied as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_COPY 6-Information Policy update has copied [dec] bytes from [chars] to [chars] An EEM policy has been copied as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_REGISTER 6-Information Policy update has successfully re-registered policy [chars] An EEM policy has been successfully re-registered as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_REGISTER 6-Information Policy update has successfully re-registered policy [chars] An EEM policy has been successfully re-registered as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_REGISTER_FAIL 6-Information Policy update has failed to register policy [chars] [chars] An EEM policy has failed to be registered as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_REGISTER_FAIL 6-Information Policy update has failed to register policy [chars] [chars] An EEM policy has failed to be registered as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_UNREGISTER_FAIL 6-Information Policy update has failed to unregister policy [chars] [chars] An EEM policy has failed to be unregistered as a result of an event manager update command ha/eem "" HA_EM-6-FMPD_UPDATE_POLICY_UNREGISTER_FAIL 6-Information Policy update has failed to unregister policy [chars] [chars] An EEM policy has failed to be unregistered as a result of an event manager update command ha/eem "" HA_EM-6-FMS_LAST_POLICY 6-Information [chars]: Cannot change a class [chars] [chars] to priority LAST. LAST is for default policies only Embedded Event Manager Scheduler Command can only change a default policy to priority LAST. ha/eem "The command is applicable to default policies only." HA_EM-6-FMS_LAST_POLICY 6-Information [chars]: Cannot change a class [chars] [chars] to priority LAST. LAST is for default policies only Embedded Event Manager Scheduler Command can only change a default policy to priority LAST. ha/eem "The command is applicable to default policies only." HA_EM-6-FMS_MODIFY_LAST_POLICY 6-Information [chars]: Cannot modify a LAST policy to class [chars]. LAST policies are for class default only. Embedded Event Manager LAST policy is for default class only. ha/eem "The command is applicable to default policies only." HA_EM-6-FMS_MODIFY_LAST_POLICY 6-Information [chars]: Cannot modify a LAST policy to class [chars]. LAST policies are for class default only. Embedded Event Manager LAST policy is for default class only. ha/eem "The command is applicable to default policies only." HA_EM-6-FMS_MODIFY_POLICY 6-Information [chars]: unable to modify the policy to class [chars]: scheduling rule unavailable. There is no scheduler rule configured to service this event class. ha/eem "Please configure a scheduler rule before modifying the event." HA_EM-6-FMS_MODIFY_POLICY 6-Information [chars]: unable to modify the policy to class [chars]: scheduling rule unavailable. There is no scheduler rule configured to service this event class. ha/eem "Please configure a scheduler rule before modifying the event." HA_EM-6-FMS_RUNNING_POLICY 6-Information [chars]: cannot [chars] a running policy with jobid [dec]. Embedded Event Manager Scheduler Command cannot change a running policy. ha/eem "The command is not applicable to a running policy." HA_EM-6-FMS_RUNNING_POLICY 6-Information [chars]: cannot [chars] a running policy with jobid [dec]. Embedded Event Manager Scheduler Command cannot change a running policy. ha/eem "The command is not applicable to a running policy." HA_EM-6-FMS_SWITCH_HARDWARE 6-Information [chars]: Policy has requested a hardware switchover An Embedded Event Manager policy requested that a hardware switchover occur. ha/eem "" HA_EM-6-FMS_SWITCH_HARDWARE 6-Information [chars]: Policy has requested a hardware switchover An Embedded Event Manager policy requested that a hardware switchover occur. ha/eem "" HA_EM-7-ACTION_CNS_AGENT_UNAVAIL 7-Debug [chars]: CNS Event Agent not available: [dec] The enqueue function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-ACTION_CNS_AGENT_UNAVAIL 7-Debug [chars]: CNS Event Agent not available: [dec] The enqueue function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-ACTION_WB_CREATE 7-Debug [chars]: create_watched_boolean failed: [chars] The create_watched_boolean function reported an error trying to create the watched boolean. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-ACTION_WB_CREATE 7-Debug [chars]: create_watched_boolean failed: [chars] The create_watched_boolean function reported an error trying to create the watched boolean. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-ACTION_WB_DELETE 7-Debug [chars]: delete_watched_boolean failed: [chars] The delete_watched_boolean function reported an error trying to delete the watched boolean. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-ACTION_WB_DELETE 7-Debug [chars]: delete_watched_boolean failed: [chars] The delete_watched_boolean function reported an error trying to delete the watched boolean. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMC_INV_REPLY 7-Debug [chars]: Application client library unable to handle message receive. The CNS Action process failed to set the restart callback. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMC_INV_REPLY 7-Debug [chars]: Application client library unable to handle message receive. The CNS Action process failed to set the restart callback. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMC_REG_CBH_PULSE 7-Debug [chars]: Unable to locate reg callback entry for pulse code [dec] The registration callback handler was unable to validate the pulse code received. ha/eem "The pthread_create function reported an error." HA_EM-7-FMC_REG_CBH_PULSE 7-Debug [chars]: Unable to locate reg callback entry for pulse code [dec] The registration callback handler was unable to validate the pulse code received. ha/eem "The pthread_create function reported an error." HA_EM-7-FMC_REG_CBH_SEND 7-Debug [chars]: Unable to send response for FH_MSG_CALLBACK_DONE [chars] The registration callback handler was unable to send the FH_MSG_CALLBACK_DONE message to the Embedded Event Manager Server. ha/eem "The pthread_create function reported an error." HA_EM-7-FMC_REG_CBH_SEND 7-Debug [chars]: Unable to send response for FH_MSG_CALLBACK_DONE [chars] The registration callback handler was unable to send the FH_MSG_CALLBACK_DONE message to the Embedded Event Manager Server. ha/eem "The pthread_create function reported an error." HA_EM-7-FMFD_DE_FETCH 7-Debug [chars]: [chars][[dec]] Internal error. The event detector has failed to fetch a data element from the statistics data engine. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_DE_FETCH 7-Debug [chars]: [chars][[dec]] Internal error. The event detector has failed to fetch a data element from the statistics data engine. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_HIST_QERR 7-Debug [chars] Internal error. The event detector has failed to get a free history list entry. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_HIST_QERR 7-Debug [chars] Internal error. The event detector has failed to get a free history list entry. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_COMPARE_OP 7-Debug [chars]: invalid comparison operator: [dec] Internal error. The value comparison operator is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_COMPARE_OP 7-Debug [chars]: invalid comparison operator: [dec] Internal error. The value comparison operator is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_STATS_TYPE 7-Debug [chars]: invalid statistics value type: [dec] Internal error. The statistics data type is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_STATS_TYPE 7-Debug [chars]: invalid statistics value type: [dec] Internal error. The statistics data type is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_TM 7-Debug [chars]: invalid timer: type=[dec] timer=%p Internal error. The timer value is invalid or not as expected. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_TM 7-Debug [chars]: invalid timer: type=[dec] timer=%p Internal error. The timer value is invalid or not as expected. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_TM_TYPE 7-Debug [chars]: invalid timer type: [dec] Internal error. The timer type is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_INV_TM_TYPE 7-Debug [chars]: invalid timer type: [dec] Internal error. The timer type is invalid or not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_MET_RBLD 7-Debug [chars]: [chars] Internal error. The event detector has failed to rebuild the metric list from the checkpointed records. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_MET_RBLD 7-Debug [chars]: [chars] Internal error. The event detector has failed to rebuild the metric list from the checkpointed records. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_MSGSEND_RETRY_ERR 7-Debug [chars]: [dec] The event detector has exceeded its maximum number of retries to send a pulse to the embedded event manager to notify of an event publish. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_MSGSEND_RETRY_ERR 7-Debug [chars]: [dec] The event detector has exceeded its maximum number of retries to send a pulse to the embedded event manager to notify of an event publish. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_OE_CREATE 7-Debug [chars]: could not create an occurrence entry Internal error. The event detector has failed to create an entry for the matched occurrence list. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_OE_CREATE 7-Debug [chars]: could not create an occurrence entry Internal error. The event detector has failed to create an entry for the matched occurrence list. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_OE_REMOVE 7-Debug [chars]: could not remove an occurrence entry Internal error. The event detector has failed to remove an entry for the matched occurrence list. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_OE_REMOVE 7-Debug [chars]: could not remove an occurrence entry Internal error. The event detector has failed to remove an entry for the matched occurrence list. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_PUB_TM_ALLOC 7-Debug [chars]: Unable to allocate memory for event publish timer block Internal error. The event detector has failed to allocate memory for the event publish timer block. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_PUB_TM_ALLOC 7-Debug [chars]: Unable to allocate memory for event publish timer block Internal error. The event detector has failed to allocate memory for the event publish timer block. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ADDR_ILLEGAL 7-Debug [chars]: Illegal SNMP address type The SNMP address is illegal. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ADDR_ILLEGAL 7-Debug [chars]: Illegal SNMP address type The SNMP address is illegal. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ADDR_IPV6 7-Debug [chars]: SNMP IPV6 address is not supported The IPV6 address is not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ADDR_IPV6 7-Debug [chars]: SNMP IPV6 address is not supported The IPV6 address is not supported. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_BUILD_PDU_FAILED 7-Debug [chars]: SNMP build pdu failed The SNMP pdu build has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_BUILD_PDU_FAILED 7-Debug [chars]: SNMP build pdu failed The SNMP pdu build has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ERRCODE 7-Debug [chars]: [chars] The SNMP error code. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_ERRCODE 7-Debug [chars]: [chars] The SNMP error code. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_MAKE_PDU_FAILED 7-Debug [chars]: SNMP make pdu failed The SNMP pdu make has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_MAKE_PDU_FAILED 7-Debug [chars]: SNMP make pdu failed The SNMP pdu make has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_OID_INVALID 7-Debug [chars]: Invalid SNMP oid length [dec] The SNMP oid has invalid length ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_OID_INVALID 7-Debug [chars]: Invalid SNMP oid length [dec] The SNMP oid has invalid length ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_REQ_FAILED 7-Debug [chars]: SNMP request failed The SNMP request has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_REQ_FAILED 7-Debug [chars]: SNMP request failed The SNMP request has failed. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_CANCEL 7-Debug [chars]: SNMP response cancelled The SNMP response has been cancelled. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_CANCEL 7-Debug [chars]: SNMP response cancelled The SNMP response has been cancelled. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_Q_EMPTY 7-Debug [chars]: SNMP proxy exec got event but queue is empty The SNMP proxy got event but the queue is empty. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_Q_EMPTY 7-Debug [chars]: SNMP proxy exec got event but queue is empty The SNMP proxy got event but the queue is empty. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_TIMEOUT 7-Debug [chars]: SNMP response has timed out The SNMP response has error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_RESP_TIMEOUT 7-Debug [chars]: SNMP response has timed out The SNMP response has error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_UNKNOWN_TYPE 7-Debug [chars]: Unknown SNMP operation or response type [dec] The operation or response type is unknown. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_UNKNOWN_TYPE 7-Debug [chars]: Unknown SNMP operation or response type [dec] The operation or response type is unknown. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_VARBIND_FAIL 7-Debug [chars]: Unable to create a SNMP varbind The oid failed to make into a SNMP varbind ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_SNMP_VARBIND_FAIL 7-Debug [chars]: Unable to create a SNMP varbind The oid failed to make into a SNMP varbind ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_TM_LEAF_NEW 7-Debug [chars]: could not create a leaf timer Internal error. The event detector has failed to create a managed leaf timer. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMFD_TM_LEAF_NEW 7-Debug [chars]: could not create a leaf timer Internal error. The event detector has failed to create a managed leaf timer. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_EVENT_TYPE 7-Debug [chars]: unknown event type [dec] An unknown Embedded Event Manager even type was detected. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_EVENT_TYPE 7-Debug [chars]: unknown event type [dec] An unknown Embedded Event Manager even type was detected. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_FORMAT_TIME 7-Debug [chars]: error attemting to format time string Format time failure. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_FORMAT_TIME 7-Debug [chars]: error attemting to format time string Format time failure. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_LAST_POLICY 7-Debug [chars]: invalid last policy name replied [chars] Internal error. The last policy name the script director replied to show fm policy registered command is an invalid policy name. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_LAST_POLICY 7-Debug [chars]: invalid last policy name replied [chars] Internal error. The last policy name the script director replied to show fm policy registered command is an invalid policy name. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_NO_MEM 7-Debug [chars]: not enough memory: [chars] Allocating memory failed due to a low-memory condition. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_NO_MEM 7-Debug [chars]: not enough memory: [chars] Allocating memory failed due to a low-memory condition. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_SWITCH_FAIL 7-Debug [chars]: The system is unable to switch to standby processor. Switchover cancelled. Switchovers must occur when STANDBY is available and ready. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMPD_SWITCH_FAIL 7-Debug [chars]: The system is unable to switch to standby processor. Switchover cancelled. Switchovers must occur when STANDBY is available and ready. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_FDC_OPEN 7-Debug [chars]: Failed to open Event Detector context control block The malloc function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_FDC_OPEN 7-Debug [chars]: Failed to open Event Detector context control block The malloc function reported an error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_INV_ARG_STRING 7-Debug [chars]: Invalid argument string: [chars] The fh_hash_md5_fd function reported the specified error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_INV_ARG_STRING 7-Debug [chars]: Invalid argument string: [chars] The fh_hash_md5_fd function reported the specified error. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_NULL_SCRIPT_NAME 7-Debug [chars]: The script name is NULL An invalid script name was passed as an argument into the specified function. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_NULL_SCRIPT_NAME 7-Debug [chars]: The script name is NULL An invalid script name was passed as an argument into the specified function. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_POLICY_EXEC 7-Debug [chars]: Policy execution [chars] An Embedded Event Manager policy requested that the system be reloaded. ha/eem "" HA_EM-7-FMS_POLICY_EXEC 7-Debug [chars]: Policy execution [chars] An Embedded Event Manager policy requested that the system be reloaded. ha/eem "" HA_EM-7-FMS_SWITCH_FAIL 7-Debug [chars]: The system is unable to switch to standby processor. Switchover cancelled. Switchovers must occur when STANDBY is available and ready. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_EM-7-FMS_SWITCH_FAIL 7-Debug [chars]: The system is unable to switch to standby processor. Switchover cancelled. Switchovers must occur when STANDBY is available and ready. ha/eem "Copy the message exactly as it appears and report it your technical " "support representative." HA_PROXY-2-HA_FIND_SERVICE_FAILED 2-Critical [chars]: unable to find [chars] service HA could not find the specified service cpp-ucode LOG_STD_ACTION HA_PROXY-2-HA_SESSION_ALLOC_FAILED 2-Critical [chars]: unable to allocate entry for [chars] binding HA could not allocate a control block to manage the service cpp-ucode LOG_STD_ACTION HA_PROXY-3-HA_DUP_SERVICE_INDEX 3-Error [chars]: Duplicate service index: [dec] on bind Duplicate service index on ha service bind cpp-ucode LOG_STD_ACTION HA_PROXY-3-HA_DUP_SERVICE_NAME 3-Error [chars]: Duplicate service name: [chars] on bind Duplicate service name on ha service bind cpp-ucode LOG_STD_ACTION HA_PROXY-3-HA_INVALID_REQUEST 3-Error [chars]: Unknown request: [dec] HA control services received unknown request cpp-ucode LOG_STD_ACTION HA_PROXY-3-HA_MALFORMED_PKT 3-Error Malformed packet bad [chars] [hec] HA Sync packet was malformed may not have been fully processed cpp-ucode LOG_STD_ACTION HA_PROXY-3-PROXY_IPC_PAK_ALLOC_FAILED 3-Error - Allocation of IPC packet failed. cpp-ucode LOG_STD_ACTION HA_PROXY-4-HA_PKT_ERROR 4-Warning Error processing HA sync pkt rg [hec] HA Sync packet was dropped while processing cpp-ucode LOG_STD_ACTION HA_PROXY-4-HA_UNKNOWN_SERVICE 4-Warning Sync msg for unknown service [hec] rg [hec] HA Sync received a message for an unknown service cpp-ucode LOG_STD_ACTION HA_TLV-2-LDP 2-Critical ERRMSG_NOFLAGS - - - HA_TLV-2-LDP 2-Critical ERRMSG_NOFLAGS - - - HA-2-CCB_PLAYBACK_ERROR 2-Critical CCB playback failed. This is a critical error message about a High Availability System status or condition. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-CCB_RECORD_ERROR 2-Critical CCB record failed. This is a critical error message about a High Availability System status or condition. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-CUTOVER_ERROR 2-Critical [chars] This is a critical error message about a High Availability System cutover status or condition. A message of this type indicates that a critical failure occurred during cutover of the standby system to the active system. Messages of this type indicate that the active system relinquished system control that the standby system failed to properly take over as the active. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-CUTOVER_NOTICE 2-Critical [chars] This is an important High Availability System notice logging the state of a system cutover of the standby system to the active system. Messages of this type indicate that the active system reliquished system control and that the standby system is taking over as active. - "If the message is due to a failure condition copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance. If the message is not due to a failure condition no action is required." HA-2-INIT_ERROR 2-Critical [chars] This is a critical error message about a High Availability System initilization status or condition. A message of this type indicates that a failure occured during high availability system initialization. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-IPC_ERROR 2-Critical [chars] [chars] This is a critical error message about a High Availability System interprocess communication status or condition. A message of this type indicates that an interprocess communication failure occurred between the active system and the standby system. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-MAX_NO_QUIESCE 2-Critical [dec] linecards not quiesced exceeds limit of [dec] all slots will be reloaded. - - "If you OIR removed the active RSP or have legacy IPs installed in the system this message is normal. Otherwise copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-2-NO_QUIESCE 2-Critical Slot [dec] did not quiesce it will be disabled and then reloaded. This is a cutover notice about a High Availability System linecard error condition. The linecard did not quiesce properly. - "This message is normal if the slot contains a legacy IP. Otherwise copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-3-ERROR 3-Error [chars] This is a error message about a High Availability System status or condition. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-3-RF_EVENT_FAILED 3-Error RF event not processed till [dec] milliseconds. Code = [dec] The event sent to the redundancy facility was not processed till the specific time delay. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-3-SYNC_ERROR 3-Error [chars] This is a error message about a High Availability System state syncronization error status or condition. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-4-CHKPT 4-Warning Platform CF - [chars] Failure in some UNIX checkpointing activity. UNIXRP_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION HA-4-CHKPTSEND 4-Warning [chars] rc [dec] event [chars] Failure to send UNIX checkpointing data. UNIXRP_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION HA-4-CONFIG_NOT_LOCKED 4-Warning Unable to lock the configuration session. This is a warning message indicating that the configuration session could not be locked. Simultaneous configuration sessions can corrupt the configuration. - "Copy the message exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-4-NOPROCESS 4-Warning Creation of [chars] process failed Creation of a platform high availability process failed. UNIXRP_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION HA-4-SYNC 4-Warning [chars] An error was encountered in a data sync operation UNIXRP_DDTS_COMPONENT LOG_STD_SH_TECH_ACTION HA-4-WARNING 4-Warning [chars] This is a warning message about a High Availability System status condition or event. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-5-HA_IOS_VERSION 5-Notice Active IOS version differs from standby IOS version This is a notice about High Availablility System version mismatch between the active and standby systems. - "No action required." HA-5-HA_VERSION 5-Notice Active HA version [dec].[dec] differs from standby HA version [dec].[dec] This is a notice about High Availablility System version mismatch between the active and standby systems. - "No action required." HA-5-HWMOD_IMG_NOTICE 5-Notice [chars] hw-module slot [dec] image [chars] : [chars] This is a notice message about a High Availability System hardware module configuration status condition or event. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-5-MODE 5-Notice Operating mode is [chars] [chars]mode is [chars]. This is a notice about the High Availablility System mode. - "Make sure that both the active system and standby systems are correctly configured and operational." HA-5-NOTICE 5-Notice [chars] This is a notice message about a High Availability System status condition or event. - "No action required." HA-5-RF_RELOAD_NOTICE 5-Notice Unable to reload the standby. [chars] The active RSP was unable to reload the standby because of the reason indicated in the message. This may be because the slave is in unplugged state or because there is a redundancy forced switchover process in progress or because the reload function is incorrectly called from the standby to the active. - - HA-5-SYNC_NOTICE 5-Notice [chars] This is a notice message about a High Availability System syncronization status condition or event. - "No action required." HA-5-SYNC_RETRY 5-Notice Reloading standby and retrying sync operation retry [dec]. This is a notice message about a High Availability System syncronization status condition or event. The syncronization operation will be retried. - "No action required." HA-5-SYNC_RETRY_FAIL 5-Notice Maximum sync retries exceeded. Reloading standby and cancelling sync. This is a notice message about a High Availability System syncronization status condition or event. The syncronization operation failed. - "Copy the notice exactly as it appears. Check both the active system and standby system for messages. Call your technical support representative for assistance." HA-6-FALLBACK 6-Information [chars] - configured mode[chars] fallback mode[chars] This RP redundancy mode fell back to the indicated mode UNIXRP_DDTS_COMPONENT LOG_STD_NO_ACTION HA-6-MODE 6-Information Operating RP redundancy mode is [chars]\n Operational redundancy mode information UNIXRP_DDTS_COMPONENT LOG_STD_NO_ACTION HA-6-STANDBY_READY 6-Information Standby RP in slot [dec] is operational in [chars] mode\n Indicates standby route processor readiness UNIXRP_DDTS_COMPONENT LOG_STD_NO_ACTION HA-6-SWITCHOVER 6-Information Route Processor switched from standby to being active This RP switched to become the active RP - LOG_STD_NO_ACTION HA-6-TOOBIG 6-Information Running config too big config sync failed The running config was too big to be synced - LOG_STD_NO_ACTION HA-6-TOOBIG 6-Information Running config too big config sync failed The running configuration was too big to be synced UNIXRP_DDTS_COMPONENT LOG_STD_NO_ACTION HAL_GENMEM-2-BAD_OPCODE 2-Critical Opcode=[hec] A bad Opcode was received by the general memory manager. cpp-ucode LOG_STD_ACTION HAL_GENMEM-3-HAL_MISMATCHED_GENMEM 3-Error VADDR:%lu LINE: [dec] Mismatched genmem. cpp-ucode LOG_STD_ACTION HAL_GPM-3-PREALLOC_FAIL 3-Error offset 0x%08lx retcode [dec] A critical failure occurred when trying pre-allocate GPM cpp-ucode LOG_STD_ACTION HAL_PACKET-3-HAL_GATHER_ASYNC_WAIT_TIMEOUT 3-Error seqnum=%lu pak-type=%lu Packet Hardware Transmit Error cpp-ucode LOG_STD_ACTION HAL_PKTMEM-2-ALLOC_FAIL 2-Critical rc 0x[hec] A critical failure occurred when trying to obtain packet memory cpp-ucode LOG_STD_ACTION HAL_PKTMEM-2-ALLOC_FAIL 2-Critical rc 0x[hec] A critical failure occurred when trying to obtain packet memory cpp-ucode LOG_STD_ACTION HAL_PKTMEM-2-OUT_OF_RESOURCES 2-Critical Packet buffer memory is low packets are being dropped Packet buffer memory is low packets are being dropped cpp-ucode LOG_STD_ACTION HAL_PKTMEM-2-OUT_OF_RESOURCES 2-Critical - Packet buffer memory is low packets are being dropped cpp-ucode LOG_STD_ACTION HAL_PKTMEM-3-UTILIZATION_SEVERE 3-Error making very aggressive adjustments to conserve [chars] buffer resources. Packet buffer utilization is at a severe level. cpp-ucode LOG_STD_ACTION HAL_PKTMEM-4-UTILIZATION_WARNING 4-Warning making more aggressive adjustments to conserve [chars] buffer resources. Packet buffer utilization is at a risky level. cpp-ucode LOG_STD_ACTION HAL_PKTMEM-5-UTILIZATION_NOTICE 5-Notice making adjustments to conserve [chars] buffer resources. Packet buffer utilization is substantial. cpp-ucode LOG_STD_ACTION HARDWARE-3-ASICNUM_ERROR 3-Error Port-ASIC number [dec] is invalid Each Port-ASIC is identified by an ID. The port ASIC number used is invalid and this is an internal error firmware LOG_STD_ACTION HARDWARE-3-PORTNUM_ERROR 3-Error port number [dec] is invalid Each interface in a given Port-ASIC is identified using an index value. The port-number used is not valid out of range firmware LOG_STD_ACTION HCCP_LC_ISSU_SHIM-3-CLC_HIGH_CPU_UTILIZATION 3-Error High CPU utilization on line card [dec]/[dec] line card ISSU may fail. Line card ISSU may fail due to high CPU utilization on the line card. cmts-platform "Attempt line card ISSU when line card has lower CPU load" HCCP_LC_ISSU_SHIM-3-REVERTIVE_CFG 3-Error HCCP revertive configuration exists for interfaces on slot [dec]/[dec]. HCCP revertive is enabled for the protect interfaces on the given line card. For ISSU to function without being disrupted by automatic revert backs please configure interfaces to be non-revertive. cmts-platform "Configure interfaces to be non-revertive." HCCP_LC_ISSU_SHIM-3-RP_HIGH_CPU_UTILIZATION 3-Error High CPU utilization on PRE line card ISSU may fail. Line card ISSU may fail due to high CPU utilization on the PRE. cmts-platform "Attempt line card ISSU when PRE has lower CPU load" HCCP_LC_ISSU_SHIM-3-SWITCHOVER_FAILURE_EXTERNAL_RF_SWITCH 3-Error Switchover from line card [dec]/[dec] aborted. HCCP switchover from the give slot is aborted due to external RF switch error in the HCCP LC ISSU shim layer. cmts-platform "Check the network connection between the router and " "the external RF switch." HCCP-3-BADCHAN 3-Error HCCP [chars] Mbr [dec] [chars]: channel switch \[chars]\ failed retries exhausted. HCCP LC member notifies failure in its channel switch. - "Make sure channel switch is functioning." HCCP-3-BADMSG 3-Error Grp [dec] Mbr [dec] [chars]: received wrong type of message-[chars]. Certain types of HCCP message are not supposed to be received by Working or Protect. - "Check configuration on this interface and the sender's interface" HCCP-3-BADSTATE 3-Error HCCP [chars] Grp [dec] inconsistant state !! HCCP state inconsistancy after control plane switchover - "Reset the interface" HCCP-3-CFG_FAIL 3-Error Configuration failed. [chars] An error occurred during configuration. - LOG_STD_SH_TECH_ACTION HCCP-3-CFR_LIST 3-Error Remove an element before destroy [chars]: cfrid=[dec] direction=[dec] state=[dec] ip_sadd=[inet] ip_daddr=[inet] dest_macaddr=[enet] src_macaddr=[enet] ip_prot=[dec] eport=[dec] Remove an element from interdb cfr_list before destroy the list. ubr10000 "Reset the system" HCCP-3-CONFIGSYNC_ERROR 3-Error Enable config-sync when it is not disabled HCCP internal flag configsync the software is trying to enable this flag set to 0 while it is already enabled 0. ubr10000 "Reset the system" HCCP-3-CTRL_PLANE_READY 3-Error HCCP ctrl plane for [chars] member [dec] is ready. HCCP ctrl plane is ready to receive lc2rp sync for the groups in list. - "." HCCP-3-DATA_PLANE_READY 3-Error HCCP data plane for [chars] member [dec] is ready. HCCP lc2rp sync for the groups in list is completed. - "." HCCP-3-INVALID_PROTECT 3-Error ERROR!LC-RED: License of protect card [dec]/[dec] is incompatible with working card [dec]/[dec]. The protect linecard has lower license. - "Please upgrade the license on the protect" HCCP-3-MISS_CTRLPLANE_READY 3-Error HCCP [chars] member [dec]: Ctrl Plane Ready is missed because [chars] HCCP ctrl plane ready is missed because of message missed or ctrl plane error. - "Check the status of ctrl plane" HCCP-3-MISS_DATAPLANE_READY 3-Error HCCP [chars] member [dec]: Data Plane Ready is missed because [chars] HCCP data plane ready is missed because of message missed or data plane error. - "Check the status of data plane" HCCP-3-MISS_STATICSYNC_DONE 3-Error HCCP [chars] member [dec]: Static Sync Done is missed because [chars] Redo static sync through CLI. HCCP static sync done is missed because of switch over happened or STATICSYNCDONE message missed. - "Perform static sync through CLI." HCCP-3-OUT_OF_ORDER_LC_MSG 3-Error HCCP slot [dec] member [dec] status [chars]: NULL hp/mp encountered. HCCP software has detected that messages are Out of Order. - LOG_STD_ACTION HCCP-3-OUT_OF_ORDER_LC2RP 3-Error Grp [dec] Mbr [dec] status [chars]: Received LC to RP sync in standby state. Message rejected. HCCP software has detected that messages are Out of Order. - LOG_STD_ACTION HCCP-3-OUT_OF_ORDER_MSG 3-Error Grp [dec] Mbr [dec] status [chars]: NULL hp encountered. HCCP software has detected that messages are Out of Order. - LOG_STD_ACTION HCCP-3-PROTECTING_TOO_MANY 3-Error Grp [dec] Mbr [dec] status [chars]: Protecting too many Workings. HCCP detected that protect is asked to protect too many working i/fs. - LOG_STD_ACTION HCCP-3-UNKNOWN_TLV 3-Error Grp [dec] Mbr [dec] [chars]: received Unknown TLV type-[dec]. HCCP software has detected Unknown TLV typesthis may not affect the functionality - LOG_STD_ACTION HCCP-4-NOREVERT 4-Warning HCCP [chars] Mbr [dec]: Revert operation cancelled. HCCP LC member will not attempt to revert back to the Working interface. - "it may have occurred because last time switchover is not finished. " "Make sure the current hccp state is in warm state" HCCP-4-NOSWOVER 4-Warning HCCP [chars] Mbr [dec]: switchover is not triggered because [chars]. HCCP LC member will not attempt to revert back to the Working interface. - "it may have occurred because last time switchover is not finished. " "Make sure the current hccp state is in warm state" HCCP-4-PEERBUSY 4-Warning HCCP [chars] member [dec] Switchover aborted. Protect [chars] is already ACTIVE for member [dec]. HCCP software has detected that the PROTECT linecard is already Active for another Working - "Please free up the Protect interface by reverting back to the " "other Working and try this switchover again" HCCP-5-BULKSYNCINCOMP 5-Notice Grp [dec] Mbr [dec] [chars]: During PRE bulk syncing ignore LC failover. Ignore LC failover event when active PRE is syncing data to standby PRE. cmts-redundancy - HCCP-5-CHANOFF 5-Notice HCCP [chars] Mbr [dec] [chars]: turning off channel. HCCP LC member notifies that it turns off channel switch. - "Make sure peer controls the channel." HCCP-5-CHANON 5-Notice HCCP [chars] Mbr [dec] [chars]: turning on channel. HCCP LC member notifies that it turns on channel switch. - "Make sure peer relinquishes the channel." HCCP-5-LC_ACTIVE 5-Notice HCCP [chars] Mbr [dec] [chars]: change state to active due to: [chars]. HCCP LC member notifies that it changes to active. - "Make sure peer relinquishes the channel." HCCP-5-LC_STANDBY 5-Notice HCCP [chars] Mbr [dec] [chars]: change state to standby due to: [chars]. HCCP LC member notifies that it changes to standby. - "Make sure peer controls the channel." HCCP-5-STANDBY 5-Notice Grp [dec] Mbr [dec] [chars]: change state from active to standby cause: [chars]. HCCP group member notifies that it changes from active to standby. - "Make sure peer controls the channel." HCCP-5-SWITCHOVERREADY 5-Notice HCCP [chars] Mbr [dec] [chars]: ready to switchover. HCCP LC member suspend timer expires ready to switchover. - "." HCCP-6-HCCP_CHAN_RFSW_SNMP_ERROR 6-Information [chars] error: [chars]. HCCP channel process errors related SNMP. - "." HCCP-6-HCCP_CHAN_RFSW_SNMP_INFO 6-Information [chars]: [chars]. SNMP response. - "." HCCP-6-IGNORE_MD_UP 6-Information The member [chars] [dec][[dec]] is already up ignore repeated event. The mac domain is already active ignore the repeated up events. - "." HCCP-6-LC_RPLC_CFGSYNC_CONFIG 6-Information HCCP [dec] [dec] [chars]: LC [chars] rplc_cfgsync configuration recover is failed PRE will download LC configurations again. HCCP recover LC rplc_cfgsync configurations is failed because last rplc_cfgsync configuration is not success. - "PRE should download LC configurations otherwise it is a critical bug." HCCP-6-LC_RPLC_CFGSYNC_CONFIG_PARSER 6-Information Parser Error: [dec] HCCP recover LC rplc_cfgsync configurations parser error. - "." HCCP-6-LC_RPLC_CFGSYNC_CONFIG_RECOVER 6-Information HCCP [dec] [dec] [chars]: LC [chars] rplc_cfgsync configuration recover is succeed. HCCP recover LC rplc_cfgsync configurations is succeed. - "." HCCP-6-STATICSYNC_COMPLETED 6-Information HCCP static sync for [chars] member [dec] is completed in [dec] ms. HCCP static sync for the groups in list is completed. - "." HD-1-BADLOOPCABLE 1-Alert Loopback not supported for a 4T DTE/X.21 port [dec] in slot [dec] Loopback mode is not allowed when using an X.21 DTE cable on a Quad\n\ serial NIM port. - "Do not enable loopback or use a different cable type." HD-1-BADPORTADAPTER 1-Alert 4T Port Adapter fault on port [dec] in slot [dec] A hardware or software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." HD-1-BADRING 1-Alert msgtxt_badringsize An internal software error occurred. - "If message recurs call your technical support representative for\n\ assistance." HD-5-LINEFLAP 5-Notice Unit [dec] excessive modem control changes Too many modem control interrupts have been received. The port was\n\ disabled to prevent excessive use of the CPU. - "Check the cable on the serial port." HDLC-1-ISSU_NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low memory condition. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." HDLC-4-ISSU_INCOMPATIBLE 4-Warning \nhdlc-issu-compat: returned FALSE The compatibility checking has failed - LOG_STD_SH_TECH_ACTION HDLC-4-ISSU_SENDFAILED 4-Warning \nHDLC ISSU: send message failed rc = [dec]\n The sending of a message has failed. - LOG_STD_SH_TECH_ACTION HDLC-4-ISSU_XFORM 4-Warning \n[chars]: failed rc=[chars] The transform has failed. - LOG_STD_SH_TECH_ACTION HDSPA_LIC-3-BOOLTIMEOUT 3-Error Fail to wait for boolean [chars] This boolean is not set true before timeout APPLICATION "This boolean is not set true before timeout" "Please check the process that set this boolean" HDSPA_LIC-3-CSB_FAIL 3-Error [chars] failed for [chars] An attempt to parse a license related CLI failed APPLICATION "Check the HDSPA license details and call TAC" HDSPA_LIC-3-FLASHERROR 3-Error [chars] Unexpected flash error happend APPLICATION "Check SPA license flash" HDSPA_LIC-5-EXCEED_HW_CAP 5-Notice DS_License installed[dec] on a single HDSPA exceeds Some of the licenses are wasted. APPLICATION "This could happen after license rehost. " "Please transfer the excess licenses to another PRE." HDSPA_LIC-5-EXCESS_LIC 5-Notice Installed license count[dec] exceeds hardware capability[dec] Some licenses are wasted currently APPLICATION "If this is caused by intentional action or RMA " "please transfer excess SPA_DS_License licenses to " "another PRE otherwise please call TAC" HDSPA_LIC-6-NOSHUT 6-Information [chars] channel [dec] has been restored to no shut Restored previously shutdown channels to no shut state APPLICATION "None" HDSPA_LIC-6-NOSHUTFAIL 6-Information [chars] channel [dec] no shut is not allowed due to insufficient licenses Unable to no shut the channel due to insufficient licenses APPLICATION "Check number of licenses installed" HDSPA_LIC-6-OUT_OF_RANGE 6-Information SPA [dec]/[dec] [chars] is already [dec] License counters have reached boundary condition APPLICATION "Internal Error check license and report to TAC" HDSPA_LIC-6-SHUT 6-Information [chars] channel [dec] has been shutdown due to insufficient licenses Unable to no shut the Channel due to insufficient licenses APPLICATION "Check number of licenses installed" HDX-3-BADFSM 3-Error On int [dec]/[dec] unexpected state [dec] event [dec] A bad state event pair is detected in the rx/tx half duplex state\n\ machine. pm-fecpm LOG_STD_ACTION HMANRP-3-MSG_CREATE_FAIL 3-Error Message creation failed [chars] Could not create tdl message polaris-emp-relay LOG_STD_ACTION HMANRP-3-MSG_GET_FAIL 3-Error Message read failed [chars] Could not fetch tdl message polaris-emp-relay LOG_STD_ACTION HMANRP-3-MSG_GET_VALUE_FAIL 3-Error Message get value failed [chars] Could not fetch value from tdl message polaris-emp-relay LOG_STD_ACTION HMANRP-3-MSG_SEND_FAIL 3-Error Message send failed [chars] Could not send tdl message polaris-emp-relay LOG_STD_ACTION HMANRP-3-SET_MSG_VALUE_FAIL 3-Error TDL set value failed [chars] Could not tdl message values polaris-emp-relay LOG_STD_ACTION HMANRP-5-CHASSIS_DOWN_EVENT 5-Notice Chassis [dec] gone DOWN! Chassis removed event polaris-emp-relay LOG_STD_ACTION HMANRP-6-ACTIVE_FLAG_SET 6-Information EMP_RELAY: Status received from active setting active status flag Setting active status flag prioritizes active switch for election polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_ELECTION_INFO 6-Information EMP active switch [dec] elected: [chars] EMP election algorithm has been run and a switch has been elected as active EMP polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_NO_ELECTION_INFO 6-Information Could not elect active EMP switch setting emp active switch to 0: [chars] Could not elect active EMP switch polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_PROCESS_EVT_STOP 6-Information EMP_RELAY: Stopping and killing the monitoring process: [chars] The monitoring process has hit an event. The process has fulfilled its purpose it can now be killed. polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_PROCESS_PREEMPT 6-Information EMP_RELAY: Preempting and killing the monitoring process: [chars] An event has occured which has rendered the watching process useless. So the system will kill this process since it is not needed anymore. polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_PROCESS_START 6-Information EMP_RELAY: Starting process for event monitoring IOS-HMAN channel gone down possibly due to HMAN process dying. The EMP IOS process monitors if this channel has come upHMAN respawned polaris-emp-relay LOG_STD_ACTION HMANRP-6-EMP_STATUS_RCVD 6-Information EMP status [dec] received from switch [dec] EMP status received from member HMAN polaris-emp-relay LOG_STD_ACTION HMANRP-6-HMAN_IOS_CHANNEL_INFO 6-Information HMAN-IOS channel event for switch [dec]: [chars] Info on HMAN-IOS events polaris-emp-relay LOG_STD_ACTION HMANRP-6-RESET_ACTIVE_FLAG 6-Information EMP_RELAY: Resetting active status flag IOS config'd shut/no shut admin_state = [dec] Resetting active status flag prioritizes active switch for election polaris-emp-relay LOG_STD_ACTION HMR-3-HASH_SIZE_ZERO 3-Error count [dec] poly [dec] An invalid hash table size of 0 was detected cpp-ucode LOG_STD_ACTION HOOD-3-BADUNIT 3-Error msgtxt_badunit An internal software error occurred. - "If the message recurs call your technical support representative\n\ for assistance." HOOD-5-CABLEERR 5-Notice Unit [dec] HP100VG cable error. Training failed A 100VG cable or hub is faulty. - "If the message recurs and either the cable or hub appears to be\n\ good repair or replace the router module." HOOD-5-COLL 5-Notice Unit [dec] excessive collisions An Ethernet cable is broken or unterminated or the transceiver is\n\ unplugged. - "If the transceiver appears to be properly terminated repair or\n\ replace the router." HOOD-5-LOSTCARR 5-Notice Unit [dec] lost carrier. Transceiver problem? An Ethernet transceiver is unplugged or faulty. - "Repair or replace the controller." HOOD-5-NOCABLE 5-Notice Unit [dec] HP100VG no tone detected. Check cable hub A 100VG cable is faulty. - "If the message recurs and either the cable or hub appears to be \n\ good repair or replace the router module." HPI-3-CODEC_NOT_LOADED 3-Error channel:[chars] DSP ID:0x[hec] command failed as codec not loaded [dec] Sending messages to DSP without a loaded codec can result with the DSP failing ios-voice LOG_STD_ACTION HPI-3-CODEC_NOT_LOADED 3-Error channel:[chars] DSP ID:0x[hec] command failed as codec not loaded [dec] Sending messages to DSP without a loaded codec can result with the DSP failing ios-voice LOG_STD_ACTION HPI-3-FAILED_START 3-Error channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec] Failed to start DSP services ios-voice LOG_STD_ACTION HPI-3-FAILED_START 3-Error channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec] Failed to start DSP services ios-voice LOG_STD_ACTION HPI-3-GSMAMRNB_LICENSE_NOT_ACTIVATED 3-Error \n********************************************************* \ \nGSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack' \ \nand accept the EULA to activate the license. \ \n*********************************************************\n Failed to start DSP services for GSM AMR-NB codec ios-licensing-atg LOG_STD_ACTION HPI-3-GSMAMRNB_LICENSE_NOT_ACTIVATED 3-Error \n********************************************************* \ \nGSM AMR-NB License is not yet activated. \ \nPlease configure 'license feature gsmamrnb-codec-pack' \ \nand accept the EULA to activate the license. \ \n*********************************************************\n Failed to start DSP services for GSM AMR-NB codec ios-licensing-atg LOG_STD_ACTION HPI-3-INVALID_PAYLOAD 3-Error wrong payload size channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec] Failed to start DSP services ios-voice LOG_STD_ACTION HPI-3-INVALID_PAYLOAD 3-Error wrong payload size channel:[chars] DSP ID:0x[hec] failed mode [dec] for service [dec] Failed to start DSP services ios-voice LOG_STD_ACTION HPI-3-NACK_HIGH 3-Error DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with high severity ios-voice - HPI-3-NACK_HIGH 3-Error DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with high severity ios-voice - HPI-3-SRTP_EVAL_FREE_ERROR 3-Error Error encountered on release SRTP bandwidth and tunnels reservation Error encountered on release SRTP bandwidth and tunnels xformers-csl LOG_STD_NO_ACTION HPI-3-SRTP_EVAL_FREE_ERROR 3-Error Error encountered on release SRTP bandwidth and tunnels reservation Error encountered on release SRTP bandwidth and tunnels xformers-csl LOG_STD_NO_ACTION HPI-4-INVALID_CODEC_LOAD 4-Warning channel:[chars] DSP ID:0x[hec] invalid hpi mode [dec] for loading codec [dec] Attempt to load codec when the DSP is in an invalid mode which can result with DSP failure ios-voice LOG_STD_ACTION HPI-4-INVALID_CODEC_LOAD 4-Warning channel:[chars] DSP ID:0x[hec] invalid hpi mode [dec] for loading codec [dec] Attempt to load codec when the DSP is in an invalid mode which can result with DSP failure ios-voice LOG_STD_ACTION HPI-4-INVALID_ECAN_TYPE 4-Warning [chars] ECAN is not available in voice-card [dec] [chars] ECAN will be used All voice cards participated in DSPFarm must have the same echo canceller type - "Make sure all voice cards participated in DSPFarm have the same echo canceller type configured" HPI-4-INVALID_ECAN_TYPE 4-Warning [chars] ECAN is not available in voice-card [dec] [chars] ECAN will be used All voice cards participated in DSPFarm must have the same echo canceller type - "Make sure all voice cards participated in DSPFarm have the same echo canceller type configured" HPI-4-NACK_MED 4-Warning DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with medium severity ios-voice "Check the NACKed message's parameters for " \"minor configuration errors. " HPI-4-NACK_MED 4-Warning DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with medium severity ios-voice "Check the NACKed message's parameters for " \"minor configuration errors. " HPI-4-NO_CLOSE 4-Warning channel:[chars] DSP ID:0x[hec] Attempt to release DSP without sending close message ios-voice LOG_STD_ACTION HPI-4-NO_CLOSE 4-Warning channel:[chars] DSP ID:0x[hec] Attempt to release DSP without sending close message ios-voice LOG_STD_ACTION HPI-6-NACK 6-Information DSP to IOS Nack message [chars] [chars] DSP to IOS Nack message with no severity in order to work with dspware without Nack severity implementation ios-voice "Information only displaying NACKed messages." HPI-6-NACK 6-Information DSP to IOS Nack message [chars] [chars] DSP to IOS Nack message with no severity in order to work with dspware without Nack severity implementation ios-voice "Information only displaying NACKed messages." HPI-6-NACK_LOW 6-Information DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with low severity ios-voice "Information only displaying NACKed messages " \"that are for debugging purposes." HPI-6-NACK_LOW 6-Information DSP to IOS Nack message with severity [chars] [chars] [chars] DSP to IOS Nack message with low severity ios-voice "Information only displaying NACKed messages " \"that are for debugging purposes." HPI-6-SRTP_EVAL_LIMIT 6-Information The SRTP bandwidth and tunnels usage exceed the license limits The SRTP bandwidth and tunnels exceed the license limits xformers-csl LOG_STD_NO_ACTION HPI-6-SRTP_EVAL_LIMIT 6-Information The SRTP bandwidth and tunnels usage exceed the license limits The SRTP bandwidth and tunnels exceed the license limits xformers-csl LOG_STD_NO_ACTION HQF-3-OH_FRAG_NOT_ALLOWED_TOGETHER 3-Error Can't configure Overhead Accounting and fragmentation together! Overhead Accouting feature currently is not allowed to coexist with fragmentation configration. qos "Remove either Overhead Accouting or fragmentation\n " HQF-3-OH_FRAG_NOT_ALLOWED_TOGETHER 3-Error Can't configure Overhead Accounting and fragmentation together! Overhead Accouting feature currently is not allowed to coexist with fragmentation configration. qos "Remove either Overhead Accouting or fragmentation\n " HQF-4-NOT_ENOUGH_BW 4-Warning interface [chars]: available bandwidth may not meet bandwidth guarantees on direction [chars] The interface bandwidth is less than the total bandwidth that is required for HQF queuing features on this interface.\n - "Increase the bandwidth available on the interface.\n" HQF-4-NOT_ENOUGH_BW 4-Warning interface [chars]: available bandwidth may not meet bandwidth guarantees on direction [chars] The interface bandwidth is less than the total bandwidth that is required for HQF queuing features on this interface.\n - "Increase the bandwidth available on the interface.\n" HQF-6-ENOUGH_BW 6-Information interface [chars]: available bandwidth now meet bandwidth guarantees on direction [chars] The interface bandwidth is now enough for the total bandwidth that is required for HQF queuing features on this interface.\n - "Do nothing.\n" HQF-6-ENOUGH_BW 6-Information interface [chars]: available bandwidth now meet bandwidth guarantees on direction [chars] The interface bandwidth is now enough for the total bandwidth that is required for HQF queuing features on this interface.\n - "Do nothing.\n" HQF-6-TUNNEL_POLICY_INST_FAILED 6-Information \nHQF-TUN: [chars] move failed to [chars] suspending policy - qos "The service-policy will be automatically restored " "if the tunnel adjacency changes again. " "Run 'show policy-map interface ' " "to see if the service policy is still suspended. " "If a service-policy remains suspended longer than expected " "then check for other messages in the log that may " "clarify the source of the problem " "e.g. insufficient bandwidth to meet bandwidth guarantees. " HQF-6-TUNNEL_POLICY_INST_FAILED 6-Information \nHQF-TUN: [chars] move failed to [chars] suspending policy - qos "The service-policy will be automatically restored " "if the tunnel adjacency changes again. " "Run 'show policy-map interface ' " "to see if the service policy is still suspended. " "If a service-policy remains suspended longer than expected " "then check for other messages in the log that may " "clarify the source of the problem " "e.g. insufficient bandwidth to meet bandwidth guarantees. " HSR_ALARM-2-HSR_RINGFAULT 2-Critical The HSR ring is now in FAULT state HSR Ring Down: The HSR ring is in FAULT state. This typically happens when both ring ports are down because of link or node failure. - - HSR_ALARM-3-HSR_PARTIALFAULT 3-Error The HSR ring is now in PARTIAL FAULT state HSR Port Down: The HSR ring is in PARTIAL FAULT state. This typically happens when one of the ring port is down because of link or node failure. The Ring is still functional but needs attention as it can not handle further faults. petra-hsr - HSRP-3-MISCONFIG 3-Error Attempt to change [chars] MAC address to [enet] when DECNET already running An HSRP group attempted to become active on an interface that can only support a single MAC address and which is running DECnet. If standby use-bia is not configured then HSRP would normally set the interface MAC address to the HSRP virtual MAC address but this is not allowed if DECnet is running. hsrp "Enable standby use-bia on the interface." HSRP-3-NOSOCKET 3-Error Unable to open socket The system was unable to initialize an IP connection for the Hot Standby protocol. hsrp "Make sure that there is at least one interface configured to run " "IP." HSRP-4-BADAUTH 4-Warning Bad authentication from [chars] group [dec] remote state [chars] Two routers participating in HSRP disagree on the valid authentication string. hsrp "Use the standby authentication command to repair the HSRP authentication \n\ discrepancy between the local system and the one whose IP address \n\ is reported." HSRP-4-BADAUTH2 4-Warning Bad authentication from [chars] Two routers participating in HSRP disagree on the valid authentication string. hsrp "Use the standby authentication command to repair the HSRP authentication " "discrepancy between the local system and the one whose IP address " "is reported." HSRP-4-BADVIP 4-Warning [chars] Grp [dec] address [chars] is in the wrong subnet for this interface The HSRP virtual IP address contained in the Hello message cannot be learnt as it is not within a subnet configured on the interface. hsrp "Check the configuration on all HSRP routers and ensure " "that the virtual IP address is within a configured subnet." HSRP-4-DIFFVIP1 4-Warning [chars] Grp [dec] active routers virtual IP address [chars] is different to the locally configured address [chars] The HSRP virtual IP address contained in the Hello message from the Active router is different from the virtual IP address configured locally. hsrp "Check the configuration on all HSRP routers in the group " "and ensure they are all configured with the same virtual " "IP address." HSRP-4-DUPADDR 4-Warning Duplicate address [chars] on [chars] sourced by [enet] The IP address in an HSRP message received on the specified interface is the same as the IP address of the router. Another router might be configured with the same IP address. The most likely cause is a network loop or a misconfigured switch that is causing the router to see its own HSRP Hello messages. hsrp "Check the configurations on all the HSRP routers to ensure " "that the interface IP addresses are unique. Check that no " "network loops exist. If port channels are configured check " "that the switch is correctly configured for port-channels. " "Enable standby use-bia so that the error message displays " "the interface MAC address of the sending router. This can " "be used to determine if the error message is caused by a " "misconfigured router or a network loop." HSRP-4-DUPVIP1 4-Warning [chars] Grp [dec] address [chars] is already assigned to [chars] group [dec] The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to a different HSRP group. hsrp "Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique." HSRP-4-DUPVIP2 4-Warning [chars] Grp [dec] address [chars] is already assigned on this interface The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to this interface. hsrp "Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique." HSRP-4-DUPVIP3 4-Warning [chars] Grp [dec] address [chars] is already assigned to or overlaps with an address on another interface or application The HSRP virtual IP address contained in the Hello message cannot be learnt as it is already assigned to or overlaps with an address on another interface or application. hsrp "Check the configuration on all HSRP routers and ensure " "that the virtual IP address of each HSRP group is unique." HSRP-5-STATECHANGE 5-Notice [chars] Grp [dec] state [chars] -> [chars] The router has changed state hsrp LOG_STD_NO_ACTION HTSP-3-CADENCENOTSUPPORTED 3-Error voice port [chars]: ring cadence not suitable for caller id. on_time_first=[dec] off_time_first=[dec] on_time_second=[dec] off_time_second=[dec] Ring off period is not sufficient for caller id transmission.\n\ If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough. - "If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough. Make sure that the\n\ cptone setting and caller-id alerting settings are correct." HTSP-3-CADENCENOTSUPPORTED 3-Error voice port [chars]: ring cadence not suitable for caller id. on_time_first=[dec] off_time_first=[dec] on_time_second=[dec] off_time_second=[dec] Ring off period is not sufficient for caller id transmission.\n\ If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough. - "If caller id transmission during ring is configured make sure\n\ that the ring off duration is long enough. Make sure that the\n\ cptone setting and caller-id alerting settings are correct." HTSP-3-CAPABILITYMISMATCH 3-Error voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]] There was a capabilities mismatch between the two call legs.\n\ capabilities are negotiated between call legs for CODEC VAD and\n\ FAX rate. - "Check that the dial peer configuration is appropriate for the interface\n\ in question. Also check that and configuration on the interface is\n\ correct." HTSP-3-CAPABILITYMISMATCH 3-Error voice port [chars]: call connection id [0x[hec] 0x[hec] 0x[hec] 0x[hec]] There was a capabilities mismatch between the two call legs.\n\ capabilities are negotiated between call legs for CODEC VAD and\n\ FAX rate. - "Check that the dial peer configuration is appropriate for the interface\n\ in question. Also check that and configuration on the interface is\n\ correct." HTSP-3-DSPALARM 3-Error voice port [chars]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All calls on the DSP were dropped\n\ and a DSP reload was attempted. - "Verify that the DSP reloaded properly by attempting to place a call\n\ on the affected voice port. Contact your technical support\n\ representative include the full text of the error message." HTSP-3-DSPALARM 3-Error voice port [chars]: status=0x[hec] message=0x[hec] text=[chars] The DSP reported a fatal error. All calls on the DSP were dropped\n\ and a DSP reload was attempted. - "Verify that the DSP reloaded properly by attempting to place a call\n\ on the affected voice port. Contact your technical support\n\ representative include the full text of the error message." HTSP-3-NOEVENT 3-Error no free event structure available from [chars] for DSP message There were no event structures remaining in the system pools to alert the\n\ router of a voice or signaling event. - "Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port." HTSP-3-NOEVENT 3-Error no free event structure available from [chars] for DSP message There were no event structures remaining in the system pools to alert the\n\ router of a voice or signaling event. - "Check that the voice port for which the event was reported is\n\ still operational. If not clear the voice port." HTSP-3-TRUNKNOTSUPPORTED 3-Error voice port [chars]: Ground Start trunking not supported This voice port does not support the 'connection trunk' command when\n\ ground start signaling is configured. Trunking mode on this voice\n\ is supported when using loop start signaling. - "Shut down the voice port remove the 'connection trunk' and/or\n\ 'signal groundStart' command from the voice port configuration\n\ and unshut the voice port." HTSP-3-TRUNKNOTSUPPORTED 3-Error voice port [chars]: Ground Start trunking not supported This voice port does not support the 'connection trunk' command when\n\ ground start signaling is configured. Trunking mode on this voice\n\ is supported when using loop start signaling. - "Shut down the voice port remove the 'connection trunk' and/or\n\ 'signal groundStart' command from the voice port configuration\n\ and unshut the voice port." HTSP-5-UPDOWN 5-Notice Trunk portchannel [[chars]] is [chars] Trunk port:channel changed state. - LOG_STD_NO_ACTION HTSP-5-UPDOWN 5-Notice Trunk portchannel [[chars]] is [chars] Trunk port:channel changed state. - LOG_STD_NO_ACTION HTSP-5-VPM_BUSYOUT 5-Notice voice port [chars]: [chars] busyout voice port busyout status changed - "use SHOW VOICE BUSYOUT to find out the reason why voice port busyout\n\ monitoring is triggered" HTSP-5-VPM_BUSYOUT 5-Notice voice port [chars]: [chars] busyout voice port busyout status changed - "use SHOW VOICE BUSYOUT to find out the reason why voice port busyout\n\ monitoring is triggered" HTSP-5-VPM_CABLE_STAT 5-Notice voice port [chars]: cable [chars] Cable for analog voice port is reconnected or removed - "Check the cable connection for this analog voice port" HTSP-5-VPM_CABLE_STAT 5-Notice voice port [chars]: cable [chars] Cable for analog voice port is reconnected or removed - "Check the cable connection for this analog voice port" HTSP-5-VPM_PCM_CAPTURE 5-Notice User trigger PCM capture is [chars] on voice port [chars] User trigger PCM capture is enabled or disable on this voice port - "This is just for information only" HTSP-5-VPM_PCM_CAPTURE 5-Notice User trigger PCM capture is [chars] on voice port [chars] User trigger PCM capture is enabled or disable on this voice port - "This is just for information only" HTTP_ALG-3-CHUNK_CREATE_FAIL 3-Error - This message indicates detection of an HTTP Java applet in a response cpp-ucode "This message is for informational purposed only but may indicate" " a security problem." HTTP-3-INIT_FAIL 3-Error \ HTTP Process Init failed. Initialization of the HTTP Subsystem has failed http "Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. " HTTP-3-OUTOF_MEM 3-Error \ HTTP out of memory. An error occurred during initialization of the HTTP process. The HTTP process could not create crucial internal data structures that are required for operation of the HTTP subsystem. The most likely reason for this condition is an exhaustion of system memory. http "Reduce other system activity to ease memory demands. if " "conditions warrant upgrade to a larger memory configuration. " HTTP-3-PROC_NOCREAT 3-Error \ Unable to create HTTP process. An error occurred during initialization of the HTTP process. The HTTP process that processes all HTTP requests and responses could not be created. - "Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. " HTTP-4-SERVER_CONN_RATE_EXCEED 4-Warning \ Number of connections per minute has exceeded the maximum limit[dec] The message indicates that the current number of connections requested per minute has exceeded the limit specified by the platform. HTTP server will resume accepting the connections 15 seconds from the time the message is issued. This restriction is done as per the HTTP throttling functionality. http "Reduce connection rate to the server." HTTP-6-SERVER_SETUP_FAILED 6-Information \ Server setup failed Setup of the HTTPS server to listen on the specified port number has failed. http "Disable the server verify that port number is correct " "and enable the server." "Reduce other system activity to ease memory demands. If " "conditions warrant upgrade to a larger memory configuration. " HTTPC-3-CACHE_MEM 3-Error \ HTTP Client Cache Init out of memory. - - - HTTPC-3-CACHE_MEM 3-Error \ HTTP Client Cache Init out of memory. - - - HTTPC-3-CONNECT_NULL 3-Error \ NULL connection structure for fd[dec] - closing socket. The HTTP Client is receiving the socket READ event but it fails to locate the connection structure for this file descriptorfd. - "Record the error and traceback and report it to the system administrator." HTTPC-3-CONNECT_NULL 3-Error \ NULL connection structure for fd[dec] - closing socket. The HTTP Client is receiving the socket READ event but it fails to locate the connection structure for this file descriptorfd. - "Record the error and traceback and report it to the system administrator." HTTPC-3-COOKIE_MEM 3-Error \ HTTP Client runs out of allowable memory to store cookies. The total memory allocated for storing cookies has run out. All cookies received from the HTTP server will be dropped. Users may no longer be able to interact with a session-based origin server until memory is freed up. - "Users may want to try their requests at a later time or contact the " "system administrator to increase the maximum RAM allowed for saving " "HTTP cookies." HTTPC-3-COOKIE_MEM 3-Error \ HTTP Client runs out of allowable memory to store cookies. The total memory allocated for storing cookies has run out. All cookies received from the HTTP server will be dropped. Users may no longer be able to interact with a session-based origin server until memory is freed up. - "Users may want to try their requests at a later time or contact the " "system administrator to increase the maximum RAM allowed for saving " "HTTP cookies." HTTPC-3-INIT_FAIL 3-Error \ HTTP Client Process Init failed. - - - HTTPC-3-INIT_FAIL 3-Error \ HTTP Client Process Init failed. - - - HTTPC-3-OUTOF_MEM 3-Error \ HTTP Client out of memory. - - - HTTPC-3-OUTOF_MEM 3-Error \ HTTP Client out of memory. - - - HTTPC-3-OUTOF_SYNC 3-Error \ HTTP Client header tables out of sync. - - - HTTPC-3-OUTOF_SYNC 3-Error \ HTTP Client header tables out of sync. - - - HTTPC-3-PROC_NOCREAT 3-Error \ Unable to create HTTP Client process. - - - HTTPC-3-PROC_NOCREAT 3-Error \ Unable to create HTTP Client process. - - - HTTPC-3-RECEIVE_SOCK_READ_EVENT_WHILE_DISABLED 3-Error \ Received socket read event while read interest is disabled callID[dec] fd[dec] - closing socket. The HTTP Client is receiving the socket READ event while the READ interest is being disabled. Something has gone wrong between the http client and the socket interfaced. - "Record the error and report it to the system administrator." HTTPC-3-RECEIVE_SOCK_READ_EVENT_WHILE_DISABLED 3-Error \ Received socket read event while read interest is disabled callID[dec] fd[dec] - closing socket. The HTTP Client is receiving the socket READ event while the READ interest is being disabled. Something has gone wrong between the http client and the socket interfaced. - "Record the error and report it to the system administrator." HTTPC-6-CLOSE_SRV_CONNECT_IPV4 6-Information \ The connection to server [inet] appears to be hung and will be closed. - - - HTTPC-6-CLOSE_SRV_CONNECT_IPV4 6-Information \ The connection to server [inet] appears to be hung and will be closed. - - - HTTPC-6-CLOSE_SRV_CONNECT_IPV6 6-Information \ The connection to server [chars] appears to be hung and will be closed. Messages are being backed up in the HTTP Client's write queue in the connection with the specified server. The connection is assumed to have gone bad and the HTTP Client is closing the connection. - "Check with the specified server for possible connection error." HTTPC-6-CLOSE_SRV_CONNECT_IPV6 6-Information \ The connection to server [chars] appears to be hung and will be closed. Messages are being backed up in the HTTP Client's write queue in the connection with the specified server. The connection is assumed to have gone bad and the HTTP Client is closing the connection. - "Check with the specified server for possible connection error." HTTPC-6-CONNECT_FAILED_IPV4 6-Information \ The connection to server [inet] failed - - - HTTPC-6-CONNECT_FAILED_IPV4 6-Information \ The connection to server [inet] failed - - - HTTPC-6-CONNECT_FAILED_IPV6 6-Information \ The connection to server [chars] failed - - - HTTPC-6-CONNECT_FAILED_IPV6 6-Information \ The connection to server [chars] failed - - - HTTPC-6-REQUEST_FAILED 6-Information \ request URI [chars] failed - - - HTTPC-6-REQUEST_FAILED 6-Information \ request URI [chars] failed - - - HUJR-3-RDWRFAIL 3-Error Read/write failed [[chars]] A read/write error occurred when accessing the hardware - LOG_STD_ACTION HUNTGRP-3-INVALID_URL 3-Error Could not open the file provided in URL: <[chars]> URL path provided can't be accessed. This usually indicates\n\ that path provided is invalid but may also be because the the\n\ path doesn't allow anonymous access to create files or open it\n\ in write mode cme-callcontrol "Check that the url path provided is valid" HUNTGRP-3-INVALID_URL 3-Error Could not open the file provided in URL: <[chars]> URL path provided can't be accessed. This usually indicates\n\ that path provided is invalid but may also be because the the\n\ path doesn't allow anonymous access to create files or open it\n\ in write mode cme-callcontrol "Check that the url path provided is valid" HUNTGRP-3-WRITE_FAIL 3-Error Could not write data to the URL: <[chars]>\n\t %%bytes written=[dec] out of [dec] Write attempt to the url path provided was unsuccessful. This usually \n\ indicates that the file was successfully opened with write and append \n\ permissions but writing all the content from buffer or may be some of \n\ it to the file failed. cme-callcontrol "" HUNTGRP-3-WRITE_FAIL 3-Error Could not write data to the URL: <[chars]>\n\t %%bytes written=[dec] out of [dec] Write attempt to the url path provided was unsuccessful. This usually \n\ indicates that the file was successfully opened with write and append \n\ permissions but writing all the content from buffer or may be some of \n\ it to the file failed. cme-callcontrol "" HW_API-3-BACKWALK_REQUEST 3-Error Backwalk request failed [chars] A request to walk internal data structures has failed. Depending on criticality of the data accuracy of forwarding may impacted. COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-BACKWALK_REQUEST 3-Error Backwalk request failed [chars] A request to walk internal data structures has failed. Depending on criticality of the data accuracy of forwarding may impacted. COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-BACKWALK_REQUEST_VALUE 3-Error Backwalk request failed [chars] 0x[hec] - - - HW_API-3-BACKWALK_REQUEST_VALUE 3-Error Backwalk request failed [chars] 0x[hec] - - - HW_API-3-INIT_FAIL 3-Error HW-API init [chars] failed[chars] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INIT_FAIL 3-Error HW-API init [chars] failed[chars] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_CONTEXT 3-Error Invalid context 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_CONTEXT 3-Error Invalid context 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_OBJ 3-Error Invalid object 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_OBJ 3-Error Invalid object 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_TYPE 3-Error Invalid type [dec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_TYPE 3-Error Invalid type [dec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_WALK_SPEC 3-Error Invalid walk spec 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-INVALID_WALK_SPEC 3-Error Invalid walk spec 0x[hec] HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-NO_OBJ_TYPE_LIST_ENTRY 3-Error Invalid sw_obj_type [dec] used with obj_type_list - - - HW_API-3-NO_OBJ_TYPE_LIST_ENTRY 3-Error Invalid sw_obj_type [dec] used with obj_type_list - - - HW_API-3-NO_OBJ_TYPE_LIST_ENTRY2 3-Error Invalid sw_obj_link_type [dec] used with obj_type_list - - - HW_API-3-NO_OBJ_TYPE_LIST_ENTRY2 3-Error Invalid sw_obj_link_type [dec] used with obj_type_list - - - HW_API-3-RESILIENCE_NO_HANDLER 3-Error No handlers in place for [chars] sw object creation failure. COMMON_HW_API_INTERNAL_ERROR COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-RESILIENCE_NO_HANDLER 3-Error No handlers in place for [chars] sw object creation failure. COMMON_HW_API_INTERNAL_ERROR COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-VECTOR 3-Error Failed to set [chars] vector for [chars] [chars] HW_API_INTERNAL_ERROR COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-VECTOR 3-Error Failed to set [chars] vector for [chars] [chars] HW_API_INTERNAL_ERROR COMMON_HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-WALK_MODE_UNSUPPORTED 3-Error Walk mode '[chars]' unsupported HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_API-3-WALK_MODE_UNSUPPORTED 3-Error Walk mode '[chars]' unsupported HW_API_INTERNAL_ERROR HW_API_DDTS_COMPONENT LOG_STD_ACTION HW_FLOWDB-3-HW_FLOWDB_DBLDEL_FEATOBJ 3-Error FlowDB featobj cannot be deleted twice. A feature attempted to remove a feature object pointer in flowDB that was already removed - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_DBLINSTALL_FEATOBJ 3-Error FlowDB featobj cannot be installed twice. A feature attempted to install a feature object pointer in flowDB that was already populated - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_IMPRECISE_INVALID_PROTOCOL 3-Error FlowDB imprecise API detected invalid protocol '[dec]'. A feature attempted to install an imprecise flow using an invalid protocol - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_INVALID_FEATOBJ 3-Error FlowDB core [dec] detected invalid featobj owned by core [dec]. A feature attempted to validate a BAD feature object pointer in flowDB - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_NOT_OWNER 3-Error FlowDB featobj remove attempted on core not owning flow. A feature attempted to remove a featobj from a BAD flowDB entry - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_NULL_FEATOBJ 3-Error FlowDB featobj install attempted with invalid pointer. A feature attempted to install a NULL feature object pointer in flowDB - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_OOM 3-Error FlowDB memory usage exceeded 95%% usage. OOM condition can occur. FlowDB running low on memory. Out-of-memory condition can occur cpp-ucode "Check sw-distrib for actual utilization of FlowDB memory" HW_FLOWDB-3-HW_FLOWDB_OOM_RECOVER 3-Error FlowDB memory usage recovered. Memory usage no longer exceeds 95%% FlowDB recovered from low memory. cpp-ucode "Check sw-distrib for actual utilization of FlowDB memory" HW_FLOWDB-3-HW_FLOWDB_STALE_FEATOBJ 3-Error FlowDB featobj remove attempted on stale entry. A feature attempted to remove a feature object pointer in flowDB from a stale flow - "Bug in feature code track down why this happened" HW_FLOWDB-3-HW_FLOWDB_VALIDATE_NO_MATCH 3-Error FlowDB failed to find matching flow during validation. A feature attempted to validate an installed flow. - "No recommended action. Output is used as a debug aid." HW_TIME-2-HB_TICK_DISCARD 2-Critical %llums since last timer heartbeat processed Something caused us to go long durations without processing timer heartbeats - "sh plat hard qfp act da inf time basic"msgdef_tac_details HW-2-OBSOLETE_HW_VER 2-Critical Module Version in [chars] is obsolete\n\ *********************************************************************\n\ * IMPORTANT !!! *\n\ * The module in [chars] is obsolete and must be returned *\n\ * via RMA to Cisco Manufacturing. If it is a lab unit * \n\ * it must be returned to Proto Services for upgrade. *\n\ *********************************************************************\n The Smart Cookie is obsolete and need to be replaced ASAP. c2800 "Contact TAC" LOG_STD_RECUR_ACTION HWMATM_MOD-3-NULLPTR 3-Error Unexpected null pointer in [chars] at [dec] An internal software error occurred. - LOG_STD_SH_TECH_ACTION I2C-3-ACCESS_ERR 3-Error I2C access error [chars] for device [dec] I2C device initialization error cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" I2C-3-CONFIG_ERR 3-Error I2C config failure [chars] for device [dec] value 0x[hec] I2C device configuration error cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" I2C-5-LTC4306 5-Notice sanity check failed: device 0x[hec] channel [dec] action [chars] retry [dec] read back 0x[hec] - cmts-platform - IAMP-4-CLIENT_ID_EXIST 4-Warning Client id [[dec]] already exists client id already exists in the database. Choose unique ID to solve this issue mediatrace "Applications could be re-registering or client id is in use by " "other application. If it is not due to duplicate registration " "it may be advisable to contact your Cisco technical support " "representative." IAMP-4-CLIENT_ID_EXIST 4-Warning Client id [[dec]] already exists client id already exists in the database. Choose unique ID to solve this issue mediatrace "Applications could be re-registering or client id is in use by " "other application. If it is not due to duplicate registration " "it may be advisable to contact your Cisco technical support " "representative." IAMP-4-CLIENT_REG_FAILED 4-Warning Client id [[dec]] could not be registered Error occured while registering the client. mediatrace "Collect show memory summary and contact your Cisco " "technical support representative." IAMP-4-CLIENT_REG_FAILED 4-Warning Client id [[dec]] could not be registered Error occured while registering the client. mediatrace "Collect show memory summary and contact your Cisco " "technical support representative." ICC-2-JOIN 2-Critical ICC mcast joining failed member <0x[hec]> to group <0x[hec]> with ipc error <[chars]> ICC was not able to join a member for the mcast group c7600-system "collect output 'show icc mcast status' from RP" ICC-2-NOMEM 2-Critical No memory available for [chars] The ICC subsystem could not obtain the memory it needed. icc LOG_STD_SH_TECH_ACTION ICC-2-OPEN 2-Critical ICC Create Session Failed for card <0x[hec]> Queue <[chars]> ICC was not able to create a session for the destination seat icc "collect output from 'show oir debug swover_global_mask' from SP" ICC-3-MAST_BAD_FREE 3-Error ICC multicast memory already freed One of the ICC multicast request's memory was found to be free when response arrived icc LOG_STD_SH_TECH_ACTION ICC-4-BAD_ACCOUNTING 4-Warning ICC received a bad class [dec] A communication failure has occurred between this card and\n\ another card in the system. icc LOG_STD_SH_TECH_ACTION ICC-4-COMM 4-Warning Communication failure occurred while [chars] - - - ICC-4-CONSISTENCY 4-Warning Internal consistency check: [chars] An internal inconsistency was found in some ICC data structures. icc LOG_STD_SH_TECH_ACTION ICC-4-HEARTBEAT 4-Warning Card [dec] failed to respond to heartbeat A communication failure has occurred between the primary and\n\ the specified line card. icc LOG_STD_SH_TECH_ACTION ICC-5-HUGE_BUFFER 5-Notice Class [[chars]] with Request id [dec] requested a huge buffer of Size [dec]. Huge packet requests would deplete the memory at the linecards - "ICC client is trying to request huge packet buffer " "Please use the command Show icc internal to get " "get the traceback and file a DDTS against the component" ICC-5-WATERMARK 5-Notice [dec] [chars] [chars] pkts for class [chars] are waiting to be processed Processor got packets for the class and are waiting to be procssed icc LOG_STD_SH_TECH_ACTION ICPM-3-ALLOC 3-Error Cannot alloc [chars] An attempt to allocate an ICPM data structure failed because\n\ of a low memory condition. mpls-ldp ACTION_STD_LOW_MEMORY_ICPM ICPM-3-ALLOC 3-Error Cannot alloc [chars] An attempt to allocate an ICPM data structure failed because\n\ of a low memory condition. mpls-ldp ACTION_STD_LOW_MEMORY_ICPM IDB_IDENTITY-3-MALLOC 3-Error Memory allocation failure for HWIDB type [dec] A memory allocation failure occured when trying to allocate the identity for this HWIDB. This HWIDB will not be allocated an IF Index which will prevent it from being used for forwarding data. ha-ifindex-sync LOG_STD_ACTION IDB_IDENTITY-3-MALLOC 3-Error Memory allocation failure for HWIDB type [dec] A memory allocation failure occured when trying to allocate the identity for this HWIDB. This HWIDB will not be allocated an IF Index which will prevent it from being used for forwarding data. ha-ifindex-sync LOG_STD_ACTION IDB_SGI-2-MEMREQ 2-Critical [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-2-MEMREQ 2-Critical [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-2-XDRREG 2-Critical [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-2-XDRREG 2-Critical [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-3-BADPTR 3-Error [chars] of interface with ifindex [dec] is invalid An internal software error occurred. Owners of the interface LOG_STD_ACTION IDB_SGI-3-BADPTR 3-Error [chars] of interface with ifindex [dec] is invalid An internal software error occurred. Owners of the interface LOG_STD_ACTION IDB_SGI-3-MEMFAIL 3-Error [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-3-MEMFAIL 3-Error [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-3-XDRREQ 3-Error [chars] An internal software error occurred. xdr LOG_STD_ACTION IDB_SGI-3-XDRREQ 3-Error [chars] An internal software error occurred. xdr LOG_STD_ACTION IDB_SGI-4-INTERR 4-Warning [chars] for interface with ifindex [dec] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-4-INTERR 4-Warning [chars] for interface with ifindex [dec] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-4-MEMBERREQ 4-Warning member request failure for interface with ifindex [dec]\n returned err - [chars] An internal software error occurred. sgi LOG_STD_ACTION IDB_SGI-4-MEMBERREQ 4-Warning member request failure for interface with ifindex [dec]\n returned err - [chars] An internal software error occurred. sgi LOG_STD_ACTION IDB_SGI-4-UNEXPINP 4-Warning [chars] An internal software error occurred. idb LOG_STD_ACTION IDB_SGI-4-UNEXPINP 4-Warning [chars] An internal software error occurred. idb LOG_STD_ACTION IDBINDEX_SYNC_KEY-3-UNKNOWN_TYPE 3-Error Interface type is unknown and cannot be synced: \[chars]\ [dec] An internal software error has occurred. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_KEY-3-UNKNOWN_TYPE 3-Error Interface type is unknown and cannot be synced: \[chars]\ [dec] An internal software error has occurred. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_ASSIGN 3-Error Failed to assign an index to IDB type [dec] for interface \[chars]\ rc=[dec] An IF-Index can not be allocated for this interface due to an internal software error. This is an unrecoverable error that results in this interface not being usable for traffic. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_ASSIGN 3-Error Failed to assign an index to IDB type [dec] for interface \[chars]\ rc=[dec] An IF-Index can not be allocated for this interface due to an internal software error. This is an unrecoverable error that results in this interface not being usable for traffic. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_ENTRY_MISMATCH 3-Error An interface index mismatched its active table entry: \[chars]\ type [dec] table index=[dec] interface index=[dec] An interface index was found which didn't match the active interface index table entry with the corresponding sync key due to an internal software error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_ENTRY_MISMATCH 3-Error An interface index mismatched its active table entry: \[chars]\ type [dec] table index=[dec] interface index=[dec] An interface index was found which didn't match the active interface index table entry with the corresponding sync key due to an internal software error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_INITKEY 3-Error Cannot initialize interface index table lookup key: \[chars]\ [dec] An internal software error has occurred. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_INITKEY 3-Error Cannot initialize interface index table lookup key: \[chars]\ [dec] An internal software error has occurred. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_LINK 3-Error Driver for IDB type '[dec]' changed the Identity of interface \[chars]\ without deleting the old Identity first rc=[dec] The IF-Index Table can not be updated with the new Identity provided for this interface due to an internal software error. Most likely the old Identity was not deleted first by the driver or that the driver accidentily changed the Identity. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_LINK 3-Error Driver for IDB type '[dec]' changed the Identity of interface \[chars]\ without deleting the old Identity first rc=[dec] The IF-Index Table can not be updated with the new Identity provided for this interface due to an internal software error. Most likely the old Identity was not deleted first by the driver or that the driver accidentily changed the Identity. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_RETRIEVE 3-Error Cannot retrieve if-index for this interface: \[chars]\ [dec] [chars] [chars] The interface index number was not found in the interface index table for the interface specified in the error message. This condition might have been caused by the interface index number not being properly synchronized by the primary processor card. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IDBINDEX_RETRIEVE 3-Error Cannot retrieve if-index for this interface: \[chars]\ [dec] [chars] [chars] The interface index number was not found in the interface index table for the interface specified in the error message. This condition might have been caused by the interface index number not being properly synchronized by the primary processor card. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-INIT_ERR 3-Error [chars] The interface index sync ISSU client has an initialization error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-INIT_ERR 3-Error [chars] The interface index sync ISSU client has an initialization error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IPC_ERR 3-Error [chars]: [chars] in domain [dec]. The interface index sync IPC session has error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-IPC_ERR 3-Error [chars]: [chars] in domain [dec]. The interface index sync IPC session has error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-ISSU_ERR 3-Error [chars][chars] rc=[dec] The interface index sync ISSU client has error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-ISSU_ERR 3-Error [chars][chars] rc=[dec] The interface index sync ISSU client has error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-LIST_REMOVE 3-Error Failed to remove node from the if-index entry list When an if-index lookup failed on the Standby the process waits on timer till the standby receives the if-index or the timer expires To know which processes are waiting a list will be maintained and when any of the above mentioned events occured the corresponding node from the list will be removed IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-LIST_REMOVE 3-Error Failed to remove node from the if-index entry list When an if-index lookup failed on the Standby the process waits on timer till the standby receives the if-index or the timer expires To know which processes are waiting a list will be maintained and when any of the above mentioned events occured the corresponding node from the list will be removed IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-RF_ERR 3-Error [chars] [dec] . The interface index sync RF client has an error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-RF_ERR 3-Error [chars] [dec] . The interface index sync RF client has an error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-TRANSFORM 3-Error Require IF-Index ISSU transformation function [chars] [chars] IF-Index Sync has identified a missing ISSU transformation function which may lead to unpredictable results. This must be resolved before the code is released. IDBINDEX_SYNC_DDTS_COMP "Contact IF-Index Sync development team with the contents of the " "configuration and error message so that the driver may be identified." IDBINDEX_SYNC-3-TRANSFORM 3-Error Require IF-Index ISSU transformation function [chars] [chars] IF-Index Sync has identified a missing ISSU transformation function which may lead to unpredictable results. This must be resolved before the code is released. IDBINDEX_SYNC_DDTS_COMP "Contact IF-Index Sync development team with the contents of the " "configuration and error message so that the driver may be identified." IDBINDEX_SYNC-3-VALIDATE 3-Error Cannot validate if-index for this interface: \[chars]\ [dec] [chars] [chars] The identity of this interface could not be validated against the stored identity within the IDB Index table. This condition is likely to have occured due to the identity of the IDB changing without first explicitly unlinking the previous identity. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-3-VALIDATE 3-Error Cannot validate if-index for this interface: \[chars]\ [dec] [chars] [chars] The identity of this interface could not be validated against the stored identity within the IDB Index table. This condition is likely to have occured due to the identity of the IDB changing without first explicitly unlinking the previous identity. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-4-RESERVE 4-Warning Failed to lookup existing ifindex for an interface on the Standby allocating a new ifindex from the Active ifindex=[dec] idbtype=[chars] Encountered a lookup failure for an interface on the Standby. An attempt has been amde to resolve the issue by reserving a possibly new ifindex on the Active. If this situation was encountered due to a defect in the key encoding then traffic may stop on this interface should the system switchover. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-4-RESERVE 4-Warning Failed to lookup existing ifindex for an interface on the Standby allocating a new ifindex from the Active ifindex=[dec] idbtype=[chars] Encountered a lookup failure for an interface on the Standby. An attempt has been amde to resolve the issue by reserving a possibly new ifindex on the Active. If this situation was encountered due to a defect in the key encoding then traffic may stop on this interface should the system switchover. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-4-TRUNCATE 4-Warning Overflow in [chars] when encoding interface sync key got [dec] maximum is [dec] When creating a unique sync key to represent an interface it has been detected that one of the attributes making up the key was truncated to fit in the allocated space in the key. This may lead to overlapping key allocations which would cause an error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBINDEX_SYNC-4-TRUNCATE 4-Warning Overflow in [chars] when encoding interface sync key got [dec] maximum is [dec] When creating a unique sync key to represent an interface it has been detected that one of the attributes making up the key was truncated to fit in the allocated space in the key. This may lead to overlapping key allocations which would cause an error. IDBINDEX_SYNC_DDTS_COMP LOG_STD_ACTION IDBINDEX_SYNC_LOG_STD_ACTION IDBMAN-3-AGGPORTMISMATCH 3-Error [chars][dec] / [dec] does match internal slot/port state [chars][dec] / [dec] There is an internal error that caused an invalid aggregate port\n\ to be used by the software. LOG_STD_ACTION IDBMAN-3-DELETEDAGGPORT 3-Error [chars][dec] / [dec] Group [dec] has been deleted but is being reused. There is an internal error that caused an interface that has been deleted\n\ to be reused for a new aggregate port. LOG_STD_ACTION IDBMAN-3-IIF_ID_REGISTRATION_FAILED 3-Error IIF_ID registration failed for Port [chars] due to memory allocation failure. Port has been shutdown The system is low on memory due to which IIF-ID registration failed. This results in failure to apply polices such as QoS and Security acls on this port. LOG_STD_REDUCE_ACTION "Once memory is available " "run 'no shutdown' on the port." IDBMAN-3-INVALIDAGGPORTBANDWIDTH 3-Error [chars][dec] / [dec] has an invalid bandwidth value of [dec] There is an internal error that caused an invalid bandwidth to be used\n\ for an aggregate port. LOG_STD_ACTION IDBMAN-3-INVALIDPORT 3-Error [chars]: trying to use invalid port number [dec] Max [dec] There is an internal error that caused an invalid port numer to be used\n\ by the software. LOG_STD_ACTION IDBMAN-3-INVALIDVLAN 3-Error [chars]: trying to use invalid Vlan [dec] There is an internal error that caused an invalid Vlan to be used \n\ by the software. LOG_STD_ACTION IDBMAN-3-NOTANAGGPORT 3-Error [chars] [dec] / [dec] is not an aggregate port There is an internal error that caused an interface that is not an aggregate\n\ port to be used for aggregate port operations LOG_STD_ACTION IDBMAN-3-PORTNOTINAGGPORT 3-Error [chars][dec] / [dec] is not present in Aggport [chars][dec] / [dec] There is an internal error that caused an invalid port to be referred\n\ to be part of an aggregate port. LOG_STD_ACTION IDBMAN-3-VLANINUSE 3-Error [chars]: Vlan [dec] is in use by [chars] Each L3 interface has a Vlan associated with it. This message indicates \n\ that the Vlan associated with the interface is being used by some other \n\ L3 Interface which is not anticipated to happen LOG_STD_NO_ACTION IDBMAN-3-VLANNOTSET 3-Error [chars]: Vlan [dec] not set since it already has Vlan [dec] There is an internal error that caused an interface to not have its\n\ Vlan set to the requested value LOG_STD_ACTION IDBMAN-4-ACTIVEPORTSINAGGPORT 4-Warning [chars] [dec] / [dec] has [dec] active ports but is being removed There is an internal error that caused an aggregate port with active ports\n\ to be removed LOG_STD_ACTION IDBMAN-4-REMOVED_NONDEFAULT_CONFIG 4-Warning Removed non default configuration for interfaces in [chars] In SSO mode the non-default configuration for any removed linecard is\n\ not synced to the standby during the bulk sync and it is removed from\n\ the configuration to avoid a config mismatch between active and standby\n\ supervisors. LOG_STD_NO_ACTION IDBMAN-6-VLANMAPPED 6-Information Vlan [dec] is mapped to [chars] Informational message indicating that the given Vlan is mapped \n\ to the given interface LOG_STD_NO_ACTION IDENT-4-LDP 4-Warning ERRMSG_LIMIT_SLOW*15 - - - IDENT-4-LDP 4-Warning ERRMSG_LIMIT_SLOW*15 - - - IDMGR-3-ID_MANAGER_INTERNAL_ERROR 3-Error [chars] Internal Error occured with ID Manager. os LOG_STD_ACTION IDMGR-3-ID_MANAGER_INTERNAL_ERROR 3-Error [chars] Internal Error occured with ID Manager. os LOG_STD_ACTION IDMGR-3-INTERRUPT 3-Error [chars] An id_get attempted at interrupt level. - LOG_STD_ACTION IDMGR-3-INTERRUPT 3-Error [chars] An id_get attempted at interrupt level. - LOG_STD_ACTION IDMGR-3-INVALID_ID 3-Error bad id in [chars] id: 0x%lX An ID Manager error occurred. - LOG_STD_ACTION IDMGR-3-INVALID_ID 3-Error bad id in [chars] id: 0x%lX An ID Manager error occurred. - LOG_STD_ACTION IDMGR-3-INVALID_ID_TABLE_SIZE 3-Error bad new ID table size A bad new table request to ID Manager occurred. - LOG_STD_ACTION IDMGR-3-INVALID_ID_TABLE_SIZE 3-Error bad new ID table size A bad new table request to ID Manager occurred. - LOG_STD_ACTION IDMGR-3-MALLOC_FAILURE 3-Error [chars] A malloc failure occured in ID Manager. - LOG_STD_ACTION IDMGR-3-MALLOC_FAILURE 3-Error [chars] A malloc failure occured in ID Manager. - LOG_STD_ACTION IDMNGR-3-CORECTXALLOC 3-Error Error: Unable to handle request %08x Unable to handle a client request identity "Contact support" IDMNGR-3-EMPTYREQ 3-Error Error: empty request received Unable to handle a client request/event identity "Contact support" IDMNGR-3-INVALIDARG 3-Error Error: Argument [chars] with NIL value Internal software error identity "Contact support" IDMNGR-3-INVALIDEVENT 3-Error Error: Invalid process event received [dec] Internal process error identity "Contact support" IDMNGR-3-INVALIDREQUEST 3-Error Error: Invalid request type received [dec] Unable to handle a client request identity "Contact support" IDMNGR-3-NOPROCESS 3-Error Error: NO idmgr process Internal software error identity "Contact support" IDMNGR-3-PROCNAME 3-Error Error: Unable to get idmgr process name for request %08x Unable to handle a client request/event identity "Contact support" IDMNGR-7-ALLOCFAIL 7-Debug Error: Failed to allocate memory for [chars] Internal software error identity "Contact support" IDS-4-ICMP_ECHO_REPLY_SIG 4-Warning Sig:2000:ICMP Echo Reply - from [inet] to [inet] - ids "This is extremely common network traffic. Suspicion should be\n\raised when a large number of these packets are found on the network. If no\n\legitimate reason for this traffic can be identified prudent security\n\practices would suggest that the source be shunned." IDS-4-ICMP_ECHO_SIG 4-Warning Sig:2004:ICMP Echo Request - from [inet] to [inet] - ids "The ICMP Echo Request is issued by the source to determine\n\if the destination is ''alive''. When the destination receives the request\n\it will reply with an ICMP Echo Reply. This request/reply pair is most\n\commonly implemented via the ''ping'' utility. Many network management tools\n\use this utility or some derivative. This is extremely common network\n\traffic. Suspicion should be raised when a large number of these packets are\n\found on the network. If no legitimate reason for this traffic can be\n\identified prudent security practices would suggest that the source be\n\shunned." IDS-4-ICMP_FRAGMENT_SIG 4-Warning Sig:2150:Fragmented ICMP Traffic - from [inet] to [inet] - ids "IP datagrams may be fragmented normally as they are\n\transported across the network but ICMP is rarely fragmented. The traffic\n\should be investigated. If no legitimate reason for the fragmentation can be\n\found and especially if the packets seem to be originating from a single\n\source prudent security practices would suggest that the host be shunned." IDS-4-ICMP_INFO_REPLY_SIG 4-Warning Sig:2010:ICMP Information Reply - from [inet] to [inet] Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP ids "This datagram type is obsolete and should not be\n\encountered. When non-specific network traffic of this type is encountered\n\the most prudent action from a security perspective is to shun or disallow\n\it. If the source of this traffic is legitimate the user will then identify\n\him or herself." IDS-4-ICMP_INFO_SIG 4-Warning Sig:2009:ICMP Information Request - from [inet] to [inet] - ids "This datagram type is obsolete and should not be\n\encountered. When non-specific network traffic of this type is encountered\n\the most prudent action from a security perspective is to shun or disallow\n\it. If the source of this traffic is legitimate the user will then identify\n\him or herself." IDS-4-ICMP_MASK_REPLY_SIG 4-Warning Sig:2012:ICMP Address Mask Reply - from [inet] to [inet] - ids "The ICMP Address Mask Request/Reply pair can be used to\n\determine the sublet mask used on the network. The requesting system issues\n\the Address Mask Request bound for a destination the destination system\n\responds with an Address Mask Reply message. This is normal network traffic\n\but is uncommon on most networks. Suspicion should be raised when a large\n\number of these packets are found on the network. If no legitimate reason\n\for this traffic can be identified prudent security practices would suggest\n\that the source be shunned." IDS-4-ICMP_MASK_SIG 4-Warning Sig:2011:ICMP Address Mask Request - from [inet] to [inet] - ids "The ICMP Address Mask Request/Reply pair can be used to\n\determine the subnet mask used on the network. The requesting system issues\n\the Address Mask Request bound for a destination the destination system\n\responds with an Address Mask Reply message. This is normal network traffic\n\but is uncommon on most networks. Suspicion should be raised when a large\n\number of these packets are found on the network. If no legitimate reason\n\for this traffic can be identified prudent security practices would suggest\n\that the source be shunned." IDS-4-ICMP_PARAMPROB_SIG 4-Warning Sig:2006:ICMP Parameter Problem on Datagram - from [inet] to [inet] Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP ids "ICMP Parameter Problem datagrams are issued when a router\n\has had to drop a datagram because it was malformed. This is a normal and\n\necessary type of network traffic. Large numbers of this datagram type on\n\the network are indicative of network difficulties or may be indicative of\n\hostile actions. If no network problems can be identified to account for the\n\traffic prudent security practices would suggest that the source be shunned." IDS-4-ICMP_PING_OF_DEATH_SIG 4-Warning Sig:2154:ICMP Ping of Death Attack - from [inet] to [inet] - ids "This indicates a denial of service attack. It is likely that the source\n\address has been spoofed making shunning ineffective" IDS-4-ICMP_REDIRECT_SIG 4-Warning Sig:2003:ICMP Redirect - from [inet] to [inet] - ids "The redirect message may be issued from a router to inform\n\a host of a better route to a requested destination. The host then updates\n\its routing table to include this route. This method of updating routing\n\tables is an uncommon practice today. When non-specific network traffic of\n\this type is encountered the most prudent action from a security\n\perspective is to shun or disallow it. If the source of this traffic is\n\legitimate the user will then identify him or herself." IDS-4-ICMP_SOURCEQUENCH_SIG 4-Warning Sig:2002:ICMP Source Quench - from [inet] to [inet] - ids "This datagram may be used in network management to provide\n\congestion control. A source quench packet will be issued when a router is\n\beginning to lose packets due to the transmission rate of a source. The\n\source quench is a request to the source to reduce the rate of datagram\n\transmission. This datagram type is rarely if ever seen on networks and some\n\systems do not even support it. Large numbers of this datagram type on the\n\network are indicative of network difficulties or may be indicative of\n\hostile actions. If no network problems can be identified to account for the\n\traffic prudent security practices would suggest that the source be shunned." IDS-4-ICMP_TIME_REPLY_SIG 4-Warning Sig:2008:ICMP Timestamp Reply - from [inet] to [inet] - ids "The ICMP Timestamp Request/Reply pair can be used to\n\synchronize system clocks on the network. The requesting system issues the\n\Timestamp Request bound for a destination the destination system responds\n\with a Timestamp Reply message. This is normal network traffic but is\n\uncommon on most networks. Suspicion should be raised when a large number of\n\these packets are found on the network. If no legitimate reason for this\n\traffic can be identified prudent security practices would suggest that the\n\source be shunned." IDS-4-ICMP_TIME_SIG 4-Warning Sig:2007:ICMP Timestamp Request - from [inet] to [inet] - ids "The ICMP Timestamp Request/Reply pair can be used to\n\synchronize system clocks on the network. The requesting system issues the\n\Timestamp Request bound for a destination the destination system responds\n\with a Timestamp Reply message. This is normal network traffic but is\n\uncommon on most networks. Suspicion should be raised when a large number of\n\these packets are found on the network. If no legitimate reason for this\n\traffic can be identified prudent security practices would suggest that the\n\source be shunned." IDS-4-ICMP_TIMXCEED_SIG 4-Warning Sig:2005:ICMP Time Exceeded for a Datagram - from [inet] to [inet] Triggers when a IP datagram is received with the \n\ ''protocol'' field of the IP header set to 1 ICMP and the ''type'' \n\msgdef_recommended_actionICMP Time Exceeded datagrams are issued when a router has\n\had to drop a datagram whose Time to Live - - IDS-4-ICMP_TOOLARGE_SIG 4-Warning Sig:2151:Large ICMP Traffic - from [inet] to [inet] While it is possible to receive ICMP datagrams that have a\n\ size greater than 1024 bytes this is a highly unusual\n\ occurrence that warrants investigation. ids "While it is possible to receive ICMP datagrams that have a\n\size greater than 1024 bytes this is a highly unusual occurrence that\n\warrants investigation. If no legitimate reason for the large packet size\n\can be found and especially if the packets seem to be originating from a\n\single source prudent security practices would suggest that the host be\n\shunned." IDS-4-ICMP_UNREACH_SIG 4-Warning Sig:2001:ICMP Host Unreachable - from [inet] to [inet] - ids "This is the common response provided to a client when there\n\is no path available to the requested host. This is a very common type of\n\network traffic. Large numbers of this datagram type on the network are\n\indicative of network difficulties or may be indicative of hostile actions.\n\If no network problems can be identified to account for the traffic prudent\n\security practices would suggest that the source be shunned." IDS-4-IP_IMPOSSIBLE_SIG 4-Warning Sig:1102:Impossible IP Packet - from [inet] to [inet] This triggers when an IP packet arrives with source\n\ equal to destination address. This signature will\n\ catch the so-called Land Attack. ids "This should never occur in legitimate traffic." IDS-4-IP_UNKNOWN_PROTO_SIG 4-Warning Sig:1101:Unknown IP Protocol - from [inet] to [inet] Triggers when an IP datagram is received with the protocol\n\ field set to 101 or greater. The use of these protocol\n\ types is highly unusual and should be investigated. ids "Locally developed protocols that may use \n\these protocol types will trigger the signature. The use of these \n\protocol types is highly unusual and should be investigated. When \n\non-specific network traffic of this type is encountered the most \n\prudent action from a security perspective is to shun or disallow it.\n\If the source of this traffic is legitimate the user will then \n\identify him or herself." IDS-4-IPFRAG_ATTACK_SIG 4-Warning Sig:1100:IP Fragment Attack - from [inet] to [inet] Triggers when any IP datagram is received with the\n\ 'more fragments' flag set to 1 or if there is an\n\ offset indicated in the offset field. ids "IP datagrams may be fragmented normally as they\n\are transported across the network. This is not uncommon but is \n\unusual enough that the traffic should be investigated. This is \n\especially important if the network is protected by a packet \n\filtering firewall." IDS-4-IPOPT_LSRR_SIG 4-Warning Sig:1004:IP options-Loose Source Route - from [inet] to [inet] Triggers on receipt of an IP datagram where the IP option\n\ list for the datagram includes option 3 Loose Source \n\ Route. This option may be misused to defeat ids "While network troubleshooting may require the \n\legitimate use of this feature this type of traffic is rarely if ever \n\noted and should comprise much less than 1% of network traffic. Small \n\amounts of source routed traffic most probably indicates that a \n\network problem is being investigated. Large amounts of source \n\routed traffic is more suspicious and a thorough investigation of the \n\source and reason is indicated." IDS-4-IPOPT_RR_SIG 4-Warning Sig:1001:IP options-Record Packet Route - from [inet] to [inet] The IP options list contains one or more options that\n\ perform various network management or debugging tasks.\n\ This alarm may indicate a reconnaissance attack is in\n\ progress against your network. ids "While network troubleshooting may require \n\the legitimate use of this feature this is unusual traffic that warrants\n\investigation. When non-specific network traffic of this type is \n\encountered the most prudent action from a security perspective is \n\to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself." IDS-4-IPOPT_SATID_SIG 4-Warning Sig:1005:IP options-SATNET ID - from [inet] to [inet] Triggers on receipt of an IP datagram where the IP\n\ option list for the datagram includes option 8 SATNET\n\ stream identifier. No known exploit exists. ids "This option is obsolete and should not be encountered. When\n\non-specific network traffic of this type is encountered the most \n\prudent action from a security perspective is to shun or disallow \n\it. If the source of this traffic is legitimate the user will then \n\identify him or herself." IDS-4-IPOPT_SECURITY_SIG 4-Warning Sig:1003:IP options-Provide schtcc - from [inet] to [inet] Triggers on receipt of an IP datagram where the IP option\n\ list for the datagram includes option 2. No known \n\ exploit exists. ids "This signature will trigger if you have \n\implemented IP security options on your network However this is \n\rarely if ever implemented . When non-specific network traffic \n\of this type is encountered the most prudent action from a security \n\perspective is to shun or disallow it. If the source of this traffic \n\is legitimate the user will then identify him or herself." IDS-4-IPOPT_SSRR_SIG 4-Warning Sig:1006:IP options-Strict Source Route - from [inet] to [inet] - ids "While network troubleshooting may require the legitimate use of this\n\feature this type of traffic is rarely if ever noted and should \n\comprise much less than 1% of network traffic. Small amounts of source \n\routed traffic most probably indicates that a network problem is being \n\investigated. Large amounts of source routed traffic is more suspicious \n\and a thorough investigation of the source and reason is indicated." IDS-4-IPOPT_TS_SIG 4-Warning Sig:1002:IP options-TimeStamp - from [inet] to [inet] - ids "While network troubleshooting may require \n\the legitimate use of this feature this is unusual traffic that warrants\n\investigation. When non-specific network traffic of this type is \n\encountered the most prudent action from a security perspective is \n\to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself." IDS-4-IPOPTS_BAD_SIG 4-Warning Sig:1000:Bad IP Option List - from [inet] to [inet] Triggers on receipt of an IP datagram where the list of IP \n\ options in the IP datagram header is incomplete or malformed.\n\ No known exploits purposely incorporate this option. ids "There is no legitimate use for malformed \n\datagrams. This may be indicative of systems that are experiencing \n\problems with their kernel or NIC cards. This is unusual traffic and \n\warrants investigation. When non-specific network traffic of this \n\type is encountered the most prudent action from a security perspective \n\is to shun or disallow it. If the source of this traffic is legitimate \n\the user will then identify him or herself." IDS-4-LOST_CONNECT 4-Warning Connection to HostID:[dec] OrgID:[dec] Triggers when a connection drops and there is no previous \n\connection. ids "This message indicates that the IDS cannot communicate with the \n\Director. Check connectivity to the Director and check Postoffice\n\configuration on both the router and the Director." IDS-4-RPC_CALLIT_REQUEST 4-Warning Sig:6103:Proxied RPC Request - from [inet] to [inet] Triggers when a proxied RPC request is sent to the portmapper\n\ of a target host. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_DUMP_REQUEST 4-Warning Sig:6102:RPC Dump - from [inet] to [inet] Triggers when an RPC dump request isissued to a target host. ids "This is a common procedure performed by many system\n\administrators and wary users to determine which RPC services are being\n\offered. Executing this procedure is most likely due to curiosity on the\n\part of a novice user or a system administrator performing system\n\maintenance. If upon investigation no valid user can be associated with this\n\event prudent security practices would suggest shunning the source." IDS-4-RPC_PORTREQ_MOUNTD 4-Warning Sig:6155:RPC mountd Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the\n\ mount daemon mountd port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_PORTREQ_REXD 4-Warning Sig:6175: RPC rexd Portmap Request - from [inet] to [inet] - ids "If this procedure is allowed on your network those users\n\who employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network it should be shunned." IDS-4-RPC_PORTREQ_YPBIND 4-Warning Sig:6151:RPC ypbind Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the YP\n\ bind daemon ypbind port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_PORTREQ_YPPASSWDD 4-Warning Sig:6152:RPC ypbind yppasswdd Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the YP\n\ password daemon yppasswdd port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_PORTREQ_YPSERV 4-Warning Sig:6150:RPC ypserv Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the YP\n\ server daemon ypserv port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_PORTREQ_YPUPDATED 4-Warning Sig:6153:RPC ypupdated Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the YP\n\ update daemon ypupdated port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_PORTREQ_YPXFRD 4-Warning Sig:6154:RPC ypxfrd Portmap Request - from [inet] to [inet] Triggers when a request is made to the portmapper for the\n\ YP transfer daemon ypxfrd port. ids "If this procedure is allowed on your network those users\n\that employ it will trigger the signature. This may be a serious attempt at\n\gaining unauthorized access and if the source of the attempt is not within\n\your network they should be shunned." IDS-4-RPC_REXD_REQUEST 4-Warning Sig:6180:RPC rexd Attempt - from [inet] to [inet] Triggers when a call to the rexd program is made. The remote execution \n\daemon is the server responsible for remote program execution. This\n\may be indicative of an attempt to gain unauthorized access to system \n\resources. ids "If this service is being used legitimately this alarm will\n\fire. For security purposes this service really should not be used." IDS-4-RPC_SET_REQUEST 4-Warning Sig:6100:RPC Port Registration - from [inet] to [inet] Triggers when attempts are made to register new RPC services\n\ on a target host. ids "No benign triggers exist for this signature. Prudent\n\security practices suggest that the source of this attempt should be\n\shunned." IDS-4-RPC_STATD_OVFLW 4-Warning Sig:6190:statd Buffer Overflow - from [inet] to [inet] Triggers when a large statd request is sent. ids "You should not see this in legitimate traffic." IDS-4-RPC_UNSET_REQUEST 4-Warning Sig:6101:RPC Port Unregistration - from [inet] to [inet] Triggers when attempts are made to unregister new RPC services\n\ on a target host. ids "No benign triggers exist for this signature. Prudent\n\security practices suggest that the source of this attempt should be\n\shunned." IDS-4-STR_MATCH_SIG 4-Warning Sig:8000:FTP Retrieve Password File - from [inet] to [inet] Triggers on string ''passwd'' issued during an FTP session. ids "System administrators might use this service to update\n\system files. It is a high security risk if this is normal practice and\n\should be avoided. No other benign triggers exist for this signature. If\n\after investigation the alarm was not generated by a system administrator\n\prudent security practices would suggest that the source be shunned." IDS-4-TCP_FIN_ONLY_SIG 4-Warning Sig:3042:TCP - FIN bit with no ACK bit in flags - from [inet] to [inet] Triggers when a TCP packet is received with the \n\ FIN bit set but with no ACK bit set in the flags field. ids "There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with the FIN bit set but with no ACK bit set in the flags \n\field in an attempt to elude intrusion dection. When non-specific network \n\traffic of this type is encountered the most prudent action from a \n\security perspective is to shun or disallow it. If the source of this \n\traffic is legitimate the user will then identify him or herself." IDS-4-TCP_FTP_CWDROOT_SIG 4-Warning Sig:3152:FTP CWD root - from [inet] to [inet] Triggers when someone tries to execute the CWD root command. IDS-4-TCP_FTP_PORT_BADADDR_SIG 4-Warning Sig:3153:FTP Improper Address Specified - from [inet] to [inet] Triggers if a port command is issued with an address that is not the same \n\as the requesting host. ids "Triggers if a port command is issued with an address that is\n\not the same as the requesting host." IDS-4-TCP_FTP_PORT_BADPORT_SIG 4-Warning Sig:3154:FTP Improper Port Specified - from [inet] to [inet] Triggers if a port command is issued with a data port specified that is \n\<1024 or >65535. ids "Triggers if a port command is issued with a data port specified\n\that is <1024 or >65535." IDS-4-TCP_FTP_SITE_SIG 4-Warning Sig:3150:FTP Remote Command Execution - from [inet] to [inet] Triggers when someone tries to execute the FTP SITE command. ids "The FTP Site command allows a user to execute a limited\n\number of commands via the FTP server on the host machine. No authentication\n\is required to execute the command. The commands that may be executed vary\n\from system to system and on many systems the SITE command is not\n\implemented. Recommend that the SITE command be disabled on FTP servers if\n\possible. If this signature is triggered from a source outside of your\n\network prudent security practices would suggest that the source be shunned." IDS-4-TCP_FTP_SYST_SIG 4-Warning Sig:3151:FTP SYST Command Attempt - from [inet] to [inet] Triggers when someone tries to execute the FTP SYST command. ids "The FTP SYST command returns the type of operating system\n\that the FTP server is running. Authentication is not required to execute\n\this command. SYST provides information that may be used to refine attack\n\methods. FTP from Linux causes SYST signature to fire. Some proxies such as\n\the TIS Toolkit issue the SYST command as a matter of course. Running an\n\FTP version with SYST disabled." IDS-4-TCP_MAJORDOMO_EXEC_BUG 4-Warning Sig:3107:Majordomo Execute Attack - from [inet] to [inet] A bug in the Majordomo program will allow remote users to\n\ execute arbitrary commands at the privilege level of the\n\ server. ids "Prudent security practices would suggest that the source of this \n\attempt be shunned." IDS-4-TCP_NO_FLAGS_SIG 4-Warning Sig:3040:TCP - No bits set in flags - from [inet] to [inet] Triggers when a TCP packet is received with no bits set\n\ in the flags field. ids "There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with no bits set in the flags field in an attempt to elude\n\intrusion dection. When non-specific network traffic of this\n\type is encountered the most prudent action from a security perspective\n\is to shun or disallow it. If the source of this traffic is legitimate\n\the user will then identify him or herself." IDS-4-TCP_SENDMAIL_BAD_FROM_SIG 4-Warning Sig:3102:Sendmail Invalid Sender - from [inet] to [inet] - ids "For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately." IDS-4-TCP_SENDMAIL_BAD_TO_SIG 4-Warning Sig:3101:Sendmail Invalid Recipient - from [inet] to [inet] - ids "For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately." IDS-4-TCP_SENDMAIL_BOUNCE_SIG 4-Warning Sig:3100:Smail Attack - from [inet] to [inet] Triggers on the very common ''smail'' attack against e-mail\n\ servers. This attack attempts to cause e-mail servers to\n\ execute programs on the attacker's behalf. ids "For security reasons users should not be allowed to execute\n\programs via e-mail servers. This is a very serious indication that your\n\network may be under attack and the source should be shunned immediately. " IDS-4-TCP_SENDMAIL_DECODE 4-Warning Sig:3105:Sendmail Decode Alias - from [inet] to [inet] Triggers on any mail message with '': decode@'' in the header.\n\ The decode alias is used to uudecode files and is primarily\n\ implemented as a convenience for system administration. ids "The decode alias is used to uudecode files and is primarily\n\implemented as a convenience for system administration. For security\n\purposes this should not be allowed and the service should be disabled. If\n\allowed users that mail to the alias will trigger this signature. Recommend\n\shunning of hosts that attempt to mail to this alias especially if they are\n\outside of your network." IDS-4-TCP_SENDMAIL_INVALID_COMMAND 4-Warning Invalid SMTP command - from [inet] to [inet] Triggers on an invalid SMTP command in the \n\ SMTP connection. This message indicates that a suspicious violation \n\ was detetected that may be an attack to the mail server system. ids "This is unusual traffic and may warrant investigation." IDS-4-TCP_SENDMAIL_OLD_SIG 4-Warning Sig:3104:Archaic Sendmail Attacks - from [inet] to [inet] Triggers when ''wiz'' or ''debug'' commands are sent to the SMTP port. ids "There is no reason for this type of traffic to be seen on\n\modern networks. There is little chance that there will be any adverse\n\effects from someone attempting these ''old'' hacks. Prudent security\n\practices would suggest that the source of this attempt be shunned." IDS-4-TCP_SENDMAIL_SPAM_SIG 4-Warning Sig:3106:Excessive Rcpt to: SPAM - from [inet] to [inet] Parse for RCPT TO: in header. Alarm on threshold. ids "Some mailing list software may trigger this signature." IDS-4-TCP_SENDMAIL_VRFY_SIG 4-Warning Sig:3103:Sendmail Reconnaissance - from [inet] to [inet] Triggers when ''expn'' or ''vrfy'' commands are issued to\n\ the SMTP port. ids "These commands are commonly used to verify that a user mail\n\account exists on the server or to expand an alias to determine who the\n\actual recipients of a message may be. Users that use the EXPN and VRFY\n\functions for legitimate purposes will trigger this signature. The\n\information that can be obtained is useful but not dangerous on its own.\n\Monitoring of future traffic for patterns of misuse is recommended." IDS-4-TCP_SYN_ATTACK_SIG 4-Warning Sig:3050:Half-Open Syn Flood - from [inet] to [inet] Triggers when the number of half-open TCP connections\n\ exceeds the high-water mark or the one minute high rate mark ids "There are no known sources that would legitimately generate\n\this traffic pattern. This may be indicative of some type of network problem\n\and should be investigated. To avoid depletion of your network resources it\n\is recommended that the source be shunned during the course of the\n\investigation. If no network problems are discovered prudent security\n\practices would suggest that the source be shunned permanently." IDS-4-TCP_SYN_FIN_SIG 4-Warning Sig:3041:TCP - SYN and FIN bits set - from [inet] to [inet] Triggers when a TCP packet is received with both the SYN\n\ and FIN bits set in the flags field. ids "There is no legitimate use for malformed TCP datagrams. This is \n\unusual traffic and warrants investigation. Hacker tools will generate\n\TCP packets with the SYN and FIN bits set in the flags field in an \n\attempt to elude\n\intrusion dection. When non-specific network traffic of this\n\type is encountered the most prudent action from a security perspective\n\is to shun or disallow it. If the source of this traffic is legitimate\n\the user will then identify him or herself." IDS-4-UDP_BOMB_SIG 4-Warning Sig:4050:UDP Bomb - from [inet] to [inet] Triggers when the UDP length specified is less than the IP\n\ length specified. This malformed packet type is associated\n\ with a denial of service attempt. ids "There is no legitimate use for malformed datagrams. This\n\may be indicative of systems that are experiencing problems with their\n\kernel or NIC cards. This is unusual traffic and warrants investigation.\n\When non-specific network traffic of this type is encountered the most\n\prudent action from a security perspective is to shun or disallow it. If the\n\source of this traffic is legitimate the user will then identify him or\n\herself." IDS-4-UDP_TFTP_PASSWD_SIG 4-Warning Sig:4100:Tftp Passwd File - from [inet] to [inet] Triggered when someone tries to tftp a password file. ids "System administrators might use this service to update\n\system files. It is a high security risk if this is normal practice and\n\should be avoided. No other benign triggers exist for this signature. If\n\after investigation the alarm was not generated by a system administrator\n\prudent security practices would suggest that the source be shunned." IDTATM25-1-DISCOVER 1-Alert Only found [dec] interfaces on bay [dec] shutting down bay The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-1-INITFAIL 1-Alert IDTATM25[dec]/[dec] Init failed at [chars]. The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-FAILSETUPVC 3-Error Interface [chars] Failed to setup vc [dec] Cause: [chars] The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-FAILTEARDOWNVC 3-Error Interface [chars] Failed to down vc [dec] Cause: [chars] The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-NOTIDTATM25 3-Error Device reported [hex] The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-RXLOSTSYNC 3-Error IDB= [chars] RX lost sync Interface reset RX hang c1400 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-TXHANG 3-Error IDB= [chars] TX hang Interface reset TX hang c1400 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-3-UNSUPPORTED 3-Error Interface [chars] [chars] not supported The ATM25 network module hardware may be bad pm-atm25 "Copy the error message exactly as it appears and report it to your " "technical support representative." IDTATM25-6-TXLIMIT 6-Information ATM transmit bandwidth is limited to smallest shaped value. Any PVC configured with traffic shaping will limit the entire ATM interface to not exceed the bandwidth of any traffic shaped pvc. - "" IDWL-3-LOOP_BACK_DETECTED 3-Error Loop-back detected on [chars]. Loop-back may be caused by accidentally plugging a balun cable into the port or there may be a misconfiguration in the network. firmware "Correct the problem causing the loopback " "condition. Then bring the port up by entering the shutdown " "then no shutdown interface configuration commands." IE3X00_LICENSE-4-FEAT_EVAL_EXPIRED 4-Warning Evaluation Period Expired for [chars] Eval Period has expired. License agent moving to eval-expired state - "Restore communication with cisco and register " " the device" IE3X00_LICENSE-4-FEAT_OOC 4-Warning Feature [chars] Out Of Compliance Existing feature configurations would be disabled on net reboot Smart License Agent enforcement mode changed to out of compliance - "Report to TAC and add sufficient licenses" IE3X00_LICENSE-5-FEAT_EVAL_MODE 5-Notice Feature [chars] is operating in Eval Mode Smart License Agent enforcement mode changed to EVAL MODE - "None" IE3X00_LICENSE-5-FEAT_IN_COMPLIANCE 5-Notice Feature [chars] is Authorized Smart License Agent enforcement mode changed to Incompliance - "None" IEDGE-3-CH_INTERNAL_ERROR 3-Error Internal error in command processing - session handle=[hex] There has been an internal error relating to CoA command processing. policy "Copy the error message exactly as it appears and " "report it to your technical support " "representative." IEDGE-3-CH_REGISTER_ERROR 3-Error CoA registration error in command processing - type '[chars]' There has been an internal error relating to CoA command processing. policy "Copy the error message exactly as it appears and " "report it to your technical support " "representative." IEDGE-4-CLOCK_CHANGE_TIMER_INV 4-Warning A Local clock change has caused a running timer to be invalid A change in local clock has made a currently running timer to be invalid sss "Check the clock configuration" IEDGE-4-PBHK_DEPLETED_INDICES 4-Warning No more portbundles can be allocated The source interfaces configured for Portbundle Hostkey feature are not sufficient and the number of portbundles available are all used up. Add more source interfaces in the configuration. sss "Check configuration on the ISG" IEDGE-4-TC_UNDEFINED_ACL 4-Warning Traffic class ACL [chars] is not defined creating permit all ACL The ACL specified for classification of traffic is not configured on the ISG. Creating a permit all ACL. ACL should be configured on the ISG. sss "Configure the ACL on the ISG" IF_FAIL-2-MPLS_TE_EXT_FWDG 2-Critical ERRMSG_NOFLAGS - - - IF_FAIL-2-MPLS_TE_EXT_FWDG 2-Critical ERRMSG_NOFLAGS - - - IF_L3_SVC_ASSOC-4-L2VPN 4-Warning ERRMSG_NOFLAGS - - - IF_L3_SVC_ASSOC-4-L2VPN 4-Warning ERRMSG_NOFLAGS - - - IF_MULTIPLE_SVC_ASSOC-4-L2VPN 4-Warning ERRMSG_NOFLAGS - - - IF_MULTIPLE_SVC_ASSOC-4-L2VPN 4-Warning ERRMSG_NOFLAGS - - - IF_PW_LIMIT_EXCEEDED-5-L2VPN 5-Notice ERRMSG_NOFLAGS - - - IF_PW_LIMIT_EXCEEDED-5-L2VPN 5-Notice ERRMSG_NOFLAGS - - - IF_SET_CFG_RESP_FAILED-3-L2VPN 3-Error ERRMSG_NOFLAGS - - - IF_SET_CFG_RESP_FAILED-3-L2VPN 3-Error ERRMSG_NOFLAGS - - - IF-2-IDB_TABLE_INIT 2-Critical Malloc failed while initializing idb table - - - IF-3-BAD_MTU 3-Error Internal error. MTU on [chars] too large or negative. Truncating from %ld to %lu.\n An internal software error occurred. The system attempted\n\ to set the MTU on an interface to an invalid value. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IF-3-BADHWUNLOCK 3-Error [chars] attempted to unlock [chars] [dec]. Locked by [chars] [dec]. Attempt to release semaphore held by another process. - "LOG_STD_ACTION" IF-3-BADLOCK 3-Error Invalid lock use for [chars]: [chars][chars] Application layer code attempted to access an unlocked interface. - "LOG_STD_ACTION" IF-3-BADMACADDRTYPE 3-Error illegal mac address type [dec] This is an interal error that was recovered gracefully. idb "LOG_STD_ACTION" IF-3-IDB_LIST_BAD_REF_COUNT 3-Error A bad reference count was encountered in an idb list element. A software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IF-3-SEMAHOG 3-Error [chars] could not get [chars] semaphore. Held by [chars]. Unable to obtain interface semaphore. - "LOG_STD_ACTION" IF-4-BACKWARD_COUNTERS 4-Warning Corrected for backward [chars] counters %llu -> %llu on [chars] - - - IF-4-NOBGPROCESS 4-Warning Network background process not running. [chars] A process which manages network interface background processing is not yet running but another system process has tried to send the process a message. idb "An interface on the router may have missed a request to bring " "itself up. If that happens it may be necessary to reset the " "interface using a shutdown operation and " "then a no shutdown. " IFDAMP-5-UPDOWN 5-Notice interface [chars] update [chars] state to [chars] interface is [chars]suppressed dampening interface changed state. ip LOG_STD_NO_ACTION IFDAMP-5-ZERODELAY 5-Notice dampening reuse timer is updated with 0 delay time Inconsistency of dampening reuse timer wheel ip LOG_STD_NO_ACTION IFM_SHIM-3-AVL_TREE 3-Error AVL tree [chars] action failed for [chars] iif-id 0x%016llx AVL tree operation failure for specific interface object in IFM-SHIM software module. This usually implies a duplicate node already existing or the tree data structure corruption. accsw-platform LOG_STD_SH_TECH_ACTION IFM_SHIM-3-INIT_FAILURE 3-Error [chars] IFM-SHIM has experienced initialization failure. accsw-platform LOG_STD_SH_TECH_ACTION IFM_SHIM-3-INTIF_CREATE_FAILURE 3-Error [chars] Internal interface not created accsw-platform LOG_STD_SH_TECH_ACTION IFM_SHIM-3-MALLOC_FAILURE 3-Error Memory allocation failure when [chars] Failed to allocated memory for a structure or event. accsw-platform LOG_STD_SH_TECH_ACTION IFM_SHIM-3-SEND_FAILURE 3-Error [chars] IFM-SHIM is experiencing message send failure. accsw-platform LOG_STD_SH_TECH_ACTION IFM_SHIM-3-SPI_FAILURE 3-Error [chars] IFM-SHIM is experiencing SPI failure. accsw-platform LOG_STD_SH_TECH_ACTION IFMAP-3-CAUSE_CFG 3-Error hash table not initialized PAL interface handle to uidb hash table not initialized cpp-ucode LOG_STD_ACTION IFMGR-3-BADIFINDEXTABLE 3-Error The file nvram:ifIndex-table is corrupt. The file is not in the expected format. none "If possible please delete the file." IFMGR-3-IFDB 3-Error IF manager interface database [chars] failure- [dec] - if_mgr "TBD" IFMGR-3-IFINDEX_PERSIST_ENTRY_CORRUPT 3-Error [chars] seems to be corrupted. Trying to read [dec] size The ifIndex-table seems to be corrupted. if_mgr "Delete the ifindex-table." IFMGR-3-IFTDB 3-Error IF manager interface table database [chars] failure- [dec] - if_mgr "TBD" IFMGR-3-INVALID_PERSISTENT_DATA 3-Error Invalid persistent data Trying to write invalid persistent data snmp-if "Copy the error message exactly as it appears and report it\n\ to your technical support representative." IFMGR-3-NOIMACP 3-Error IF manager control process failed to start - if_mgr "TBD" IFMGR-3-NOTYPEVECTOR 3-Error Interface manager failed to allocate IF type vector. size [dec] The interface type vector was not able to be allocated with the number of elements required--initially or resize. if_mgr "TBD" IFMGR-3-NOVECTOR 3-Error Interface manager failed to allocate IF vector. size [dec] The interface vector was not able to be allocated with the number of elements required--initially or resize see size in the error message. if_mgr "TBD" IFMGR-3-VECTOREXD 3-Error IF manager attempted to use interface [dec] outside vector range. This message indicates that an interface with too large of an ifIndex value was attempted to be added to the IF-MGR DB. if_mgr "Additional IF-MGR warning and/or error messages should accompany" "indication of this error. These additional messages should provide more" "details on the effected interface." IFMGR-3-VECTORPOSUSED 3-Error IF manager attempted to add interface [dec] which was already added. This message comes from the IF-MGR DB when it is trying to add an ifIndex value for this interface which already exists in the ifIndex DB. if_mgr "TBD" IFMGR-4-NOIFINDEX 4-Warning All SNMP if indices are exhausted All SNMP MIB indices have been exhausted. Interfaces will\n\ not be able to obtain an interface index that they can \n\ use to register with the interface MIB. if_mgr "Attempt a system reload. If the problem persists after the\n\ system reload copy the message exactly as it appears on\n\ the console or in the system log contact your Cisco\n\ technical support representative and provide the\n\ representative with the gathered information." IFMGR-4-NOSYNC 4-Warning ifIndex not being synced between active and standby When the standby comes up then the tuple of ifIndex and ifDescr\n\ is synced so that when interfaces comes up they get the same ifIndex.\n\ This error happens when the interface doesn't get the ifIndex for\n\ the given ifDescr if_mgr "Inform the technical support to raise the ddts" IFMGR-4-STACK_RELATIONSHIP_ADD_ERROR 4-Warning [chars]: Request for creating invalid stack relationship [dec] [dec] Interfaces have same ifIndex in IF-MGR assigned list. The 2nd interface registered with IF-MGR will be assigned with new index if_mgr "1. No Action if ifIndex persist is not required." "2. Reload the standby RP if ERR msg only seen in standby RP" "3. Reload the router with the proper ifindex-table and image" IFMGR-4-VECTORIFSUSPECT 4-Warning IF manager added interface [dec] which is unexpectedly large. The ifIndex allocation scheme gives out sequential ifIndex values. This message comes from the IF-MGR DB when it is trying to add an ifIndex value much larger than the former greatest ifIndex value in the DB. if_mgr "TBD" IFMGR-5-RESTART 5-Notice [chars] The IF MGR process has restarted if_mgr "This is an informational message. The system should recover on its" " own." IFMGR-7-NO_IFINDEX_FILE 7-Debug Unable to open [chars] [chars] This is a informational message. This means system found no saved ifIndex information and ifIndex is not persisted across reboots. The ifIndices will be reassigned. if_mgr "1. No Action if 'snmp-server ifIndex persist' is not configured. " "2. If 'snmp-server ifindex persist' is configured then copy the error" " message exactly as it appears and report it to your technical" " support representative." IFS-3-FS_CREATE_FAIL 3-Error Failed to create [chars] file system [chars] An internal software error occurred. Determine the component from the traceback displayed in the\n\ error message. "Call your technical support representative for assistance." IFS-3-FS_CREATE_FAIL2 3-Error Failed to create [chars] simple file system [chars] An internal software error occurred. Determine the component from the traceback displayed in the\n\ error message. "Call your technical support representative for assistance." IFS-3-FS_MISSING_FUNCTIONS 3-Error '[chars]' file system missing required functions not created Some file systems require a certain set of function to be present in\n\ order to be usable. This file sustem does not support all the\n\ mandatory functionality. Determine the component from the traceback displayed in the\n\ error message. "Call your technical support representative for assistance." IFS-3-FS_STRUCT_ERROR 3-Error Data does not match expected internal representation A mismatch exists between the representation of data extracted from the filesystem and the expectation of its formatting. This may occur when running in a dual-RP environment with different IOS versions running on the two RPs. ifs "Ensure both RPs are running the IOS same version if running in " "a dual-RP environment. If not call your technical support " "representative for assistance." IFS-3-FSDUP 3-Error Failed to add [chars] filesystem prefix exists A file system cound not be added because another file system exists\n\ with the same name. Determine the component from the traceback displayed in the\n\ error message. "Contact your technical support representative." IFS-3-FSMAX 3-Error Failed to add [chars] maximum filesystems [dec] The router has reached the maximum number of file systems that\n\ can be supported at one time. ifs "Contact your technical support representative." IFS-4-FILEMAX 4-Warning Failed to open [chars] maximum open files [dec] The router has reached the maximum number of files that may\n\ be open at one time. ifs "Close some files and try again. If this messages recurs contact your\n\ technical support representative." IGMP_QUERIER-4-NO_IP_ADDR_CFG 4-Warning The IGMP querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system. An IP address should be specified for the IGMP querier either at the global or per VLAN level. igmp "Configure a source IP address for the IGMP querier. " IGMP_QUERIER-4-PIM_ENABLED 4-Warning The IGMP querier is operationally disabled in VLAN [dec] because PIM has been enabled on the SVI. PIM has been detected on the SVI. The IGMP querier function should not be operationally enabled when PIM is enabled on the SVI. igmp "Ensure that PIM is disabled on the SVI. " IGMP_QUERIER-4-QUERIER_MROUTER_DETECTED 4-Warning An external IGMP querier or a multicast router has been detected in VLAN [dec] on port [chars]. An external querier or multicast router has been detected in the VLAN. The IGMP querier function should not be enabled when there is external querier or multicast router present in the VLAN. igmp "Either manually disable the IGMP querier on this system or disable " "querier or PIM/DVMRP on the multicast routers identified. The IGMP " IGMP_QUERIER-4-SAME_SRC_IP_ADDR 4-Warning An IGMP General Query packet with the same source IP address [inet] The IGMP querier has received an IGMP General Query message with a source IP address identical to that configured for the IGMP querier itself. This is considered a network configuration error. igmp "Check IGMP querier source IP address configuration on the router " "or switch connected via the port identified." "Ensure unique source IP addresses are configured on each system. " IGMP_QUERIER-4-SNOOPING_DISABLED 4-Warning The IGMP querier is operationally disabled in VLAN [dec] because IGMP snooping has been disabled in this VLAN. IGMP snooping has been detected as being disabled on this VLAN. The IGMP querier function should not be operationally enabled when IGMP snooping is disabled. igmp "Ensure that IGMP snooping is enabled globally and on the VLAN " "reported. " IGMP_QUERIER-4-VLAN_NOT_FWD 4-Warning The IGMP querier is operationally disabled in VLAN [dec] because VLAN is not in forwarding state. The IGMP querier function is not be operationally enabled when VLAN is not forwarding. igmp "Check spanning tree state for this VLAN." IGMP_QUERIER-4-ZERO_SRC_IP_ADDR 4-Warning An IGMP General Query packet with source IP address that contained all zeroes is received in VLAN [dec] on port [chars]. The IGMP querier has received an IGMP General Query message with a source IP address that contained all zeroes. Some IGMP clients cannot process General Query with source IP address that contained all zeroes. igmp "Check the source IP address of the IGMP querier that is on the router " "or switch connected to the port specified in the message. " IGMP_QUERIER-6-NO_QUERIER_MROUTER_DETECTED 6-Information The IGMP querier is now operationally enabled in VLAN [dec] because no external querier or multicast router has been detected. No external querier or multicast router has been detected. As a result the IGMP querier function has now been enabled. igmp "No action is required." IGMP_QUERIER-6-PIM_DISABLED 6-Information The IGMP querier is now operationally enabled in VLAN [dec] because PIM is no longer enabled on the SVI. PIM has been disabled on the SVI and as a result the IGMP querier function has now been enabled. igmp "No action is required." IGMP_QUERIER-6-SNOOPING_ENABLED 6-Information The IGMP querier is now operationally enabled in VLAN [dec] because IGMP snooping is no longer disabled. IGMP snooping has now been enabled and as a result the IGMP querier function has now been enabled. igmp "No action is required." IGMP_QUERIER-6-VLAN_FWD 6-Information The IGMP querier is now operationally enabled in VLAN [dec] because the VLAN has entered forwarding state. The VLAN has been placed in the forwarding state and as a result the IGMP querier function has now been enabled. igmp "No action is required." IGMP_SNOOP_ISSU-2-GET_BUFFER 2-Critical IGMP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars] The IGMP Snooping ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. igmp-snooping "show logging and show checkpoint client" IGMP_SNOOP_ISSU-2-GET_BUFFER 2-Critical IGMP Snooping ISSU client failed to get buffer for message. Error: [dec] [chars] The allocation of explicit-tracking entries is bounded to avoid\n\ the IGMP/MLD snooping hogs the system resources igmp/mld snooping "Disable and re-enable L2 multicast snooping on the VLAN." IGMP_SNOOP_ISSU-2-INIT 2-Critical IGMP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars] The IGMP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. igmp-snooping LOG_STD_ACTION IGMP_SNOOP_ISSU-2-INIT 2-Critical IGMP Snooping ISSU client initialization failed to [chars]. Error: [dec] [chars] The IGMP Snooping ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. igmp-snooping LOG_STD_ACTION IGMP_SNOOP_ISSU-2-SEND_NEGO_FAILED 2-Critical IGMP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars] The IGMP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. igmp-snooping "show logging and show checkpoint client" IGMP_SNOOP_ISSU-2-SEND_NEGO_FAILED 2-Critical IGMP Snooping ISSU client failed to send negotiation message. Error: [dec] [chars] The IGMP Snooping ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. igmp-snooping "show logging and show checkpoint client" IGMP_SNOOP_ISSU-2-SESSION_NEGO 2-Critical IGMP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The IGMP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. igmp-snooping "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-2-SESSION_NEGO 2-Critical IGMP Snooping ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The IGMP Snooping ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. igmp-snooping "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-2-SESSION_REGISTRY 2-Critical IGMP Snooping ISSU client failed to register session information. Error: [dec] [chars] The IGMP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. igmp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-2-SESSION_REGISTRY 2-Critical IGMP Snooping ISSU client failed to register session information. Error: [dec] [chars] The IGMP Snooping ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. igmp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-3-INVALID_SESSION 3-Error IGMP Snooping ISSU client does not have a valid registered session. The IGMP Snooping ISSU client does not have a valid registered session. igmp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-3-INVALID_SESSION 3-Error IGMP Snooping ISSU client does not have a valid registered session. The IGMP Snooping ISSU client does not have a valid registered session. igmp-snooping "show issu capability entries and " "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-3-MSG_NOT_OK 3-Error IGMP Snooping ISSU client 'Message Type [dec]' is not compatible The IGMP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed. igmp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " IGMP_SNOOP_ISSU-3-MSG_NOT_OK 3-Error IGMP Snooping ISSU client 'Message Type [dec]' is not compatible The IGMP Snooping ISSU client received an incompatible message from the peer device. The message cannot be processed. igmp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " IGMP_SNOOP_ISSU-3-MSG_SIZE 3-Error IGMP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The IGMP Snooping ISSU client failed to calculate the MTU for the specified message. The IGMP Snooping ISSU client is not able to send the message to the standby device. igmp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " IGMP_SNOOP_ISSU-3-MSG_SIZE 3-Error IGMP Snooping ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The IGMP Snooping ISSU client failed to calculate the MTU for the specified message. The IGMP Snooping ISSU client is not able to send the message to the standby device. igmp-snooping "show issu message group and " "show issu session and " "show issu negotiated version " IGMP_SNOOP_ISSU-3-SESSION_UNREGISTRY 3-Error IGMP Snooping ISSU client failed to unregister session information. Error: [dec] [chars] The IGMP Snooping ISSU client failed to unregister session information. igmp-snooping "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-3-SESSION_UNREGISTRY 3-Error IGMP Snooping ISSU client failed to unregister session information. Error: [dec] [chars] The IGMP Snooping ISSU client failed to unregister session information. igmp-snooping "show issu session and " "show issu negotiated capability " IGMP_SNOOP_ISSU-3-TRANSFORM_FAIL 3-Error IGMP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The IGMP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IGMP Snooping state between the active device and the standby device is not identical. igmp-snooping "show issu session and " "show issu negotiated version " IGMP_SNOOP_ISSU-3-TRANSFORM_FAIL 3-Error IGMP Snooping ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The IGMP Snooping ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IGMP Snooping state between the active device and the standby device is not identical. igmp-snooping "show issu session and " "show issu negotiated version " IGMP -3-DNS_ERROR 3-Error DNS lookup time out. DNS lookup for ssm mapping will be disabled for 60 sec. DNS source lookup time out. DNS server did not respond \n\ to the DNS query this may be due to DNS server is down. \n\ DNS lookup will be stopped for next 60 sec. - "Disable DNS lookup for ssm mapping till the DNS " "server comes up." LOG_STD_ACTION IGMP -3-DNS_ERROR 3-Error DNS lookup time out. DNS lookup for ssm mapping will be disabled for 60 sec. DNS source lookup time out. DNS server did not respond \n\ to the DNS query this may be due to DNS server is down. \n\ DNS lookup will be stopped for next 60 sec. - "Disable DNS lookup for ssm mapping till the DNS " "server comes up." LOG_STD_ACTION IGMP-3-IGMP_CLIENT_ID_ERR 3-Error Invalid Client Id usage [dec]. Invalid Client Id usage - "Check the Client Id" LOG_STD_NO_ACTION IGMP-3-IGMP_CLIENT_ID_ERR 3-Error Invalid Client Id usage [dec]. Invalid Client Id usage - "Check the Client Id" LOG_STD_NO_ACTION IGMP-3-IGMP_LIST_DEL_STATIC 3-Error Failed to delete static groups for interface [chars]. Repeated attempts to walk the list failed. mcast-igmp LOG_STD_ACTION IGMP-3-IGMP_LIST_DEL_STATIC 3-Error Failed to delete static groups for interface [chars]. Repeated attempts to walk the list failed. mcast-igmp LOG_STD_ACTION IGMP-3-IGMP_LIST_RESET_SOURCE_FLAGS 3-Error Failed to reset source flags for [inet]. Repeated attempts to reset the flags failed. mcast-igmp LOG_STD_ACTION IGMP-3-IGMP_LIST_RESET_SOURCE_FLAGS 3-Error Failed to reset source flags for [inet]. Repeated attempts to reset the flags failed. mcast-igmp LOG_STD_ACTION IGMP-3-NO_DNS_SERVER 3-Error No DNS server is configured. \nDNS-based SSM mapping should be disabled if no DNS server is configured. There is no DNS server present. Processing IGMP \n\ packets may be delayed if the DNS-lookup is done continuosly. - "Disable DNS-based SSM mapping if there is \n\ no DNS-server present in the network." LOG_STD_ACTION IGMP-3-NO_DNS_SERVER 3-Error No DNS server is configured. \nDNS-based SSM mapping should be disabled if no DNS server is configured. There is no DNS server present. Processing IGMP \n\ packets may be delayed if the DNS-lookup is done continuosly. - "Disable DNS-based SSM mapping if there is \n\ no DNS-server present in the network." LOG_STD_ACTION IGMP-3-QUERY_INT_MISMATCH 3-Error Received a non-matching query interval [dec] from querier address [inet] Mismatch of IGMP version found between routers. - "Configure both the interfaces with same IGMP version." LOG_STD_ACTION IGMP-3-QUERY_INT_MISMATCH 3-Error Received a non-matching query interval [dec] from querier address [inet] Mismatch of IGMP version found between routers. - "Configure both the interfaces with same IGMP version." LOG_STD_ACTION IGMP-4-MROUTE_IC_FLAG 4-Warning While adding or deleting multicast state some state may not correctly have local interest flag set or cleared. Repeated attempts to adjust local interest flag were running over time and some state may not have been adjusted. - LOG_STD_SH_TECH_ACTION IGMP-4-MROUTE_IC_FLAG 4-Warning While adding or deleting multicast state some state may not correctly have local interest flag set or cleared. Repeated attempts to adjust local interest flag were running over time and some state may not have been adjusted. - LOG_STD_SH_TECH_ACTION IGMP-4-NO_INPUT 4-Warning IGMP packet without input interface received from [inet] for [inet] An unexpected IGMP packet without input interface was received. ipmulticast "Consider taking note of source and destination present in syslog." LOG_STD_ACTION IGMP-4-NO_INPUT 4-Warning IGMP packet without input interface received from [inet] for [inet] An unexpected IGMP packet without input interface was received. ipmulticast "Consider taking note of source and destination present in syslog." LOG_STD_ACTION IGMP-6-IGMP_CHANNEL_LIMIT 6-Information IGMP limit exceeded for channel [inet] [inet] on [chars] by host [inet] - - - IGMP-6-IGMP_CHANNEL_LIMIT 6-Information IGMP limit exceeded for channel [inet] [inet] on [chars] by host [inet] - - - IGMP-6-IGMP_GROUP_LIMIT 6-Information IGMP limit exceeded for group * [inet] on [chars] by host [inet] - - - IGMP-6-IGMP_GROUP_LIMIT 6-Information IGMP limit exceeded for group * [inet] on [chars] by host [inet] - - - IGNITION-4-IGN_FAILED_CMD 4-Warning Ignition Management hardware failed to execute the '[chars]' command. Code: [dec] The hardware MCU responsible for the ignition power management is not responding properly to software commands. aventus-platform LOG_STD_RECUR_ACTION IGNITION-4-IGN_OVER_VOLTAGE 4-Warning The input voltage is at [dec].[dec] V. The overvoltage threshold of [dec].[dec] V has been tripped recently. Shutdown sequence will begin. The input voltage became higher than the overvoltage threshold and the router might shutdown shortly. aventus-platform "Reduce the input power supply voltage." IGNITION-4-IGN_REJECT_SETTING 4-Warning Incompatible 'under voltage' setting [dec].[dec] V was not applied. The The under voltage threshold value was set to a higher value then actual input voltage and applying this setting would cause the router to shutdown shortly aventus-platform LOG_STD_RECUR_ACTION IGNITION-4-IGN_UNDER_VOLTAGE 4-Warning The input voltage below the undervoltage threshold of [dec].[dec] V was detected. The system may shutdown. The input voltage became lower than the undervoltage threshold and the router might shutdown shortly. aventus-platform "Increase the input power supply voltage." IGNITION-4-IGN_UNDER_VOLTAGE_END 4-Warning The input voltage above the undervoltage threshold of [dec].[dec] V was detected. The input voltage became higher than the undervoltage threshold. aventus-platform LOG_STD_NO_ACTION IGNITION-5-IGN_DEBUG_SET 5-Notice Ignition Management debugging [chars] is turned [chars] The system's debugging facility is turned on or off aventus-platform LOG_STD_NO_ACTION IGNITION-5-IGN_ENABLE_CMD 5-Notice The Ignition Power Management is [chars] The system administrator has enabled the Ignition Power Management feature. aventus-platform LOG_STD_NO_ACTION IGNITION-5-IGN_RELOAD_SYS 5-Notice The Ignition Power Management is preparing for shutdown The Ignition Power Management is about to shut the system down. aventus-platform LOG_STD_NO_ACTION IGNITION-5-IGN_SENSE_CMD 5-Notice The Ignition Voltage Sense is [chars] The system administrator has enabled the Ignition Voltage Sense feature. aventus-platform LOG_STD_NO_ACTION IGNITION-5-IGN_TURNED_ON_OFF 5-Notice The ignition is turned [chars] The ignition state changed between ON and OFF. aventus-platform LOG_STD_NO_ACTION IIOT_3RDPARTY-0-POWERED_OFF 0-Emergency 3rd-party module is powered off 3rd-party module is powered off by CLI command IIOT_3RDPARTY_COMPONENT "No action recommended" LOG_STD_ACTION IIOT_3RDPARTY-0-POWERED_ON 0-Emergency 3rd-party module is powered on 3rd-party module is powered on by CLI command IIOT_3RDPARTY_COMPONENT "No action recommended" LOG_STD_ACTION IIOT_3RDPARTY-0-SLOT_ASSIGNED 0-Emergency 3rd-party module bay number is assigned to [dec]. 3rd-party module bay number is assigned by CLI command. IIOT_3RDPARTY_COMPONENT "No action recommended" LOG_STD_ACTION IIOT_3RDPARTY-0-SLOT_CLEARED 0-Emergency 3rd-party moudle bay number is cleared. previously configured 3rd-party module bay number is cleared. IIOT_3RDPARTY_COMPONENT "No action recommended" LOG_STD_ACTION IIOT_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_ASSERT 0-Emergency External alarm/digital IO port [chars] asserted\n External alarm/digital IO port alert is detected - "No action recommended" LOG_STD_ACTION IIOT_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_CLEAR 0-Emergency External alarm/digital IO port [chars] cleared\n External alarm/digital IO port alert is cleared SPARROW_COMPONENT "No action recommended" LOG_STD_ACTION IKEV2-1-SEND_COOKIE_CHALLENGE 1-Alert NULL - ipsec-ikev2 - IKEV2-1-SEND_COOKIE_CHALLENGE 1-Alert NULL - ipsec-ikev2 - IKEV2-3-NEG_ABORT 3-Error NULL - ipsec-ikev2 - IKEV2-3-NEG_ABORT 3-Error NULL - ipsec-ikev2 - IKEV2-5-INCREASE_PEER_WINDOW_SIZE 5-Notice NULL - ipsec-ikev2 - IKEV2-5-INCREASE_PEER_WINDOW_SIZE 5-Notice NULL - ipsec-ikev2 - IKEV2-5-IPSEC_COLLISION 5-Notice NULL - ipsec-ikev2 - IKEV2-5-IPSEC_COLLISION 5-Notice NULL - ipsec-ikev2 - IKEV2-5-OSAL_INITIATE_TUNNEL 5-Notice NULL - ipsec-ikev2 - IKEV2-5-OSAL_INITIATE_TUNNEL 5-Notice NULL - ipsec-ikev2 - IKEV2-5-RECV_CONNECTION_REQUEST 5-Notice NULL - ipsec-ikev2 - IKEV2-5-RECV_CONNECTION_REQUEST 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_DOWN 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_DOWN 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_REJECTED_LIMIT_REACHED 5-Notice [chars] - ipsec-ikev2 - IKEV2-5-SA_REJECTED_LIMIT_REACHED 5-Notice [chars] - ipsec-ikev2 - IKEV2-5-SA_REJECTED_RESOURCE_LOW 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_REJECTED_RESOURCE_LOW 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_UP 5-Notice NULL - ipsec-ikev2 - IKEV2-5-SA_UP 5-Notice NULL - ipsec-ikev2 - ILACC-1-INITFAIL 1-Alert msgtxt_initfail The hardware failed to initialize correctly. - "Repair or replace the controller." ILACC-1-MEMERR 1-Alert msgtxt_memoryerror An Ethernet interface detected a hardware problem. - "Repair or replace the controller." ILACC-3-BADUNIT 3-Error msgtxt_badunit An internal software error occurred. - "If this message recurs contact your technical support representative." ILACC-3-OWNERR 3-Error msgtxt_ownerror An Ethernet interface is malfunctioning or an internal software error\n\ occurred. - "Repair or replace the controller." ILACC-3-SPURIDON 3-Error Unit [dec] spurious IDON interrupt csr[dec]=0x%04x An Ethernet interface generated a spurious Initialization Done\n\ interrupt. - "Repair or replace the controller." ILACC-3-UNDERFLO 3-Error Unit [dec] underflow error The Ethernet hardware is requesting data faster than the system can\n\ supply it. This condition might indicate that the system is at the\n\ limit of its performance. - "A small number of underflows might not be a cause for concern. You can\n\ monitor underflows with the show interface command. Reducing the load\n\ on the router or installing a higher-performance router should\n\ alleviate this problem." ILACC-4-BABBLE 4-Warning Unit [dec] babble error csr0 = 0x[hec] An Ethernet interface is malfunctioning. - "Determine whether the malfunction stems from a software or hardware\n\ error by turning off all fast switching. Error messages showing that the packet is too large for the link\n\ indicate a software error at a high level. Copy the error message exactly as it appears and report it to your\n\ technical support representative. Receiving no error messages indicates a hardware error. \n\ Repair or replace the controller." ILACC-5-COLL 5-Notice Unit [dec] excessive collisions. TDR=[dec] - - "If the transceiver appears to be properly terminated repair or\n\ replace the Ethernet interface card." ILACC-5-LATECOLL 5-Notice Unit [dec] late collision error An Ethernet transceiver is malfunctioning the Ethernet is overloaded\n\ or the Ethernet cable is too long. - "Repair or replace the controller." ILACC-5-LOSTCARR 5-Notice Unit [dec] lost carrier. Transceiver problem? An Ethernet transceiver is unplugged or faulty. - "Repair or replace the controller." ILLEGAL-3-VFI 3-Error ERRMSG_FLAG_TRACEBACK - - - ILLEGAL-3-VFI 3-Error ERRMSG_FLAG_TRACEBACK - - - ILLEGAL-3-XCONNECT 3-Error ERRMSG_FLAG_TRACEBACK - - - ILLEGAL-3-XCONNECT 3-Error ERRMSG_FLAG_TRACEBACK - - - ILP_ISSU-3-BUFFER 3-Error Platform ILPower ISSU client failed to get buffer for msg error [dec] Platform Inline Power ISSU client failed to get buffer for building\n\ a negotiation message. Hence it can send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. platform-ha "show logging and show checkpoint client" ILP_ISSU-3-CAP_INVALID_SIZE 3-Error Platform Inline Power ISSU client capability list is empty. The Platform Inline Power ISSU client capability exchange list size\n\ is invalid. platform-ha "show issu capability entries " ILP_ISSU-3-CAP_NOT_COMPATIBLE 3-Error Platform Inline Power ISSU client capability exchange result incompatible. The Platform ILPower ISSU client capability exchange has negotiated\n\ as incompatible with the peer. platform-ha "show issu negotiated capability " ILP_ISSU-3-CAPABILITY 3-Error Platform Inline Power ISSU client [chars] Platform Inline Power ISSU client observed an error during capability\n\ negotiation. When this error happens there is a mismatch\n\ between the client capability between the active and\n\ standby unit. platform-ha "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " ILP_ISSU-3-INIT 3-Error Platform Inline Power ISSU client initialization failed at [chars] error [chars] Platform ILP ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. platform-ha LOG_STD_SH_TECH_ACTION ILP_ISSU-3-MSG_NOT_OK 3-Error Platform Inline Power ISSU client message [dec] is not compatible Platform Inline Power ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it can be processed by this unit platform-ha "show issu message group and\n\ show issu session and\n\ show issu negotiated version " ILP_ISSU-3-MSG_SIZE 3-Error Platform Inline Power ISSU client failed to get the message size for message [dec] Platform Inline Power ISSU client failed to calculate message size\n\ for the message specified. The Platform ILPower ISSU client will not\n\ be able to send message to the standby unit. platform-ha "show issu message group and\n\ show issu session and\n\ show issu negotiated version " ILP_ISSU-3-POLICY 3-Error Platform Inline Power ISSU client message type [dec] is [chars] Platform Inline Power ISSU client received an message type which it\n\ does not support. The policy is applied to make the session\n\ compatible. platform-ha "show issu session " ILP_ISSU-3-SEND_FAILED 3-Error Platform Inline Power ISSU client failed to send a negotiation message error [dec] Platform ILPower ISSU client could not send a session negotiation\n\ message to the peer. When there is a problem in the\n\ negotiation the standby unit can not be brought up. platform-ha "show logging and show checkpoint client" ILP_ISSU-3-SESSION 3-Error Platform ILPower ISSU client [chars] Platform Inline Power ISSU client observed an error during a session\n\ negotiation with the peer unit. When there is a problem\n\ with the session the standby unit can not be brought up. platform-ha "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " ILP_ISSU-3-SESSION_UNREGISTRY 3-Error Platform ILPower ISSU client failed to unregister session information. Error: [dec] [chars] The Platform Inline Power ISSU client failed to unregister session information. platform-ha "show issu session and " "show issu negotiated capability " ILP_ISSU-3-TRANSFORM 3-Error Platform Inline Power ISSU client [chars] transform failed error [chars] Platform Inline Power ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Platform Inline Power state will not\n\ be indentical with the active unit. platform-ha "show issu session and\n\ show issu negotiated version " ILPOWER_ISSU-3-GET_BUFFER 3-Error Inline power ISSU client failed to get buffer for message.\n\ Error: [dec] [chars] Inline power ISSU client failed to get buffer for building\n\ a negotiation message. Hence it cannot send the negotiation\n\ message to the standby unit. When there is a problem in\n\ the negotiaiton the standby unit can not be brought up. ilpower "show logging and show checkpoint client" ILPOWER_ISSU-3-INIT 3-Error Inline power ISSU client initialization failed to [chars].Error: [dec] [chars] Inline power ISSU client could not be initiailzed this will\n\ cause catstrophic failure when ISSU upgrade or downgrade\n\ is performed. ilpower LOG_STD_SH_TECH_ACTION ILPOWER_ISSU-3-INVALID_SESSION 3-Error Inline power ISSU client does not have a valid registered session. Inline power ISSU client does not have a valid registered session.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. ilpower "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " ILPOWER_ISSU-3-MSG_NOT_OK 3-Error Inline power ISSU client message type [dec] is not compatible Inline power ISSU client received an incompatible message\n\ from the peer unit. Since the message is not compatible\n\ it cannot be processed by this unit ilpower "show issu message group and\n\ show issu session and\n\ show issu negotiated version " ILPOWER_ISSU-3-MSG_SIZE 3-Error Inline power ISSU client failed to get the MTU for message type [dec].\n\ Error: [dec] [chars] Inline power ISSU client failed to calculate MTU\n\ for the message specified. The dot1x ISSU client will not\n\ be able to send message to the standby unit. ilpower "show issu message group and\n\ show issu session and\n\ show issu negotiated version " ILPOWER_ISSU-3-SEND_NEGO_FAILED 3-Error Inline power ISSU client failed to send negotiation message.\n\ Error: [dec] [chars] Inline power ISSU client failed to send a session negotiation\n\ message to the peer. When there is a problem in the ISSU\n\ negotiation the standby unit can not be brought up. ilpower "show logging and show checkpoint client" ILPOWER_ISSU-3-SESSION_NEGO 3-Error Inline power ISSU client encountered unexpected client nego_done.\n\ Error: [dec] [chars] Inline power ISSU client encountered an unexpected 'client\n\ negotiation done'. ilpower "show issu session and\n\ show issu negotiated capability " ILPOWER_ISSU-3-SESSION_REGISTRY 3-Error Inline power ISSU client failed to register session information.\n\ Error: [dec] [chars] Inline power ISSU client failed to register session information.\n\ When there is a problem with the session the standby unit cannot\n\ be brought up. ilpower "show issu capability entries and\n\ show issu session and\n\ show issu negotiated capability " ILPOWER_ISSU-3-SESSION_UNREGISTRY 3-Error Inline power ISSU client failed to unregister session information.\n\ Error: [dec] [chars] Inline power ISSU client failed to unregister session information. ilpower "show issu session and\n\ show issu negotiated capability " ILPOWER_ISSU-3-TRANSFORM_FAIL 3-Error Inline power ISSU client [chars] transform failed for message type [dec].\n\ Error: [dec] [chars] Inline power ISSU client could not transform the message.\n\ If the transmit transformation failed it means that the\n\ checkpoint message can not be sent to the standby unit.\n\ If the receive transformation failed it means that the\n\ checkpoint message can not be applied on the standby\n\ unit. In both cases the Inline power state will not\n\ be indentical with the active unit. ilpower "show issu session and\n\ show issu negotiated version " ILPOWER-2-PRIO_CRIT_LIMIT 2-Critical Priority [dec] reached critical limit. Load shedding can lead to chassis reload. Please avoid configuring any more ports at this priority level. Maximum interface power is used for this calculation. This priority level reached maximum allowed wattage inline-power "Please distribute ports to another priority" ILPOWER-2-PRIO_CRIT_LIMIT_SVL 2-Critical On Chassis [dec] priority [dec] reached critical limit. Load shedding can lead to chassis reload. Please avoid configuring any more ports at this priority level. Maximum interface power is used for this calculation. This priority level reached maximum allowed wattage inline-power "Please distribute ports to another priority" ILPOWER-3-CONTROLLER_ERR 3-Error Controller error Controller number [dec]: [chars] An error reported or caused by the Power over Ethernet PoE controller is detected. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_ERR 3-Error Controller error Controller number [dec]: [chars] An error reported or caused by the Power over Ethernet PoE controller is detected. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_IF_ERR 3-Error Controller interface error [chars]: [chars] An interface error is detected between the Power over Ethernet PoE controller and system. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_IF_ERR 3-Error Controller interface error [chars]: [chars] An interface error is detected between the Power over Ethernet PoE controller and system. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_PORT_ERR 3-Error Controller port error Interface [chars]: [chars] A port error reported by the Power over Ethernet PoE controller is detected. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_PORT_ERR 3-Error Controller port error Interface [chars]: [chars] A port error reported by the Power over Ethernet PoE controller is detected. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-CONTROLLER_POST_ERR 3-Error Inline Power Feature is disabled on this switch because\n\ Power On Self Test POST failed on this switch.\n\msgdef_explanation An error reported or caused by the Power over Ethernet - - - ILPOWER-3-CONTROLLER_POST_ERR 3-Error Inline Power Feature is disabled on this switch because\n\ Power On Self Test POST failed on this switch.\n\msgdef_explanation An error reported or caused by the Power over Ethernet - - - ILPOWER-3-ILPOWER_INTERNAL_IF_ERROR 3-Error Inline Power internal error interface [chars]: [chars] A software check failed during Power over Ethernet PoE processing. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-ILPOWER_INTERNAL_IF_ERROR 3-Error Inline Power internal error interface [chars]: [chars] A software check failed during Power over Ethernet PoE processing. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-3-SHUT_OVERDRAWN 3-Error Interface [chars] is shutdown as it is consuming more than the maximum configured power [dec] milliwatts. Interface is shutdown because it is consuming more than the maximum configured power inline-power "Make sure correct power is budgeted for this interfac\n\e based on the power device electrical specifications or ratings. It is recommended to change the police cutoff power to a higher value to keep the device powered on" ILPOWER-3-SHUT_OVERDRAWN 3-Error Interface [chars] is shutdown as it is consuming more than the maximum configured power [dec] milliwatts. Interface is shutdown because it is consuming more than the maximum configured power inline-power "Make sure correct power is budgeted for this interfac\n\e based on the power device electrical specifications or ratings. It is recommended to change the police cutoff power to a higher value to keep the device powered on" ILPOWER-4-ILPOWER_POWER_SUPPLY 4-Warning PoE Power Supply [chars]: [chars] The power supply for PoE is OIR inline-power "Make sure power supply to PoE input is inserted after removal" ILPOWER-4-ILPOWER_POWER_SUPPLY 4-Warning PoE Power Supply [chars]: [chars] The power supply for PoE is OIR inline-power "Make sure power supply to PoE input is inserted after removal" ILPOWER-4-ILPOWER_PS_ABSENCE 4-Warning PoE module Power Supply not present \n\ Inline Power Feature is disabled on [chars] because Power On Self Test POST failed \n : [chars] The power supply for PoE expansion module is not present or not inserted properly or faulty inline-power "Make sure power supply to expansion module is inserted properly\ and reload the switch with PoE power supply present" ILPOWER-4-ILPOWER_PS_ABSENCE 4-Warning PoE module Power Supply not present \n\ Inline Power Feature is disabled on [chars] because Power On Self Test POST failed \n : [chars] The power supply for PoE expansion module is not present or not inserted properly or faulty inline-power "Make sure power supply to expansion module is inserted properly\ and reload the switch with PoE power supply present" ILPOWER-4-LOG_OVERDRAWN 4-Warning Interface [chars] is overdrawing power. it is consuming [dec] milliwatts where as maximum configured power is [dec] milliwatts. - inline-power "Make sure correct power is budgeted for this interface based on the power device electrical specifications or ratings. Otherwise you might risk overloading the switch. It is recommended to change the police cutoffpower appropriately if needed" ILPOWER-4-LOG_OVERDRAWN 4-Warning Interface [chars] is overdrawing power. it is consuming [dec] milliwatts where as maximum configured power is [dec] milliwatts. - inline-power "Make sure correct power is budgeted for this interface based on the power device electrical specifications or ratings. Otherwise you might risk overloading the switch. It is recommended to change the police cutoffpower appropriately if needed" ILPOWER-4-PRIO_WARN_LIMIT 4-Warning Priority [dec] is reaching critical limit. Maximum interface power is used for this calculation. This priority level reached warning limit wattage inline-power "Please don't configure any more ports " "at this priority." ILPOWER-4-PRIO_WARN_LIMIT_SVL 4-Warning On Chassis [dec] priority [dec] is reaching critical limit. Maximum interface power is used for this calculation. This priority level reached warning limit wattage inline-power "Please don't configure any more ports at this priority" ILPOWER-4-WARNING 4-Warning Power-over-Ethernet is disabled on this switch \n\ PoE functionality requires a power input of 44 to 57 Volts DC The power supply voltage is NOT in range 44 V-57 V to support PoE/PoE+ inline-power "Make sure the power supply Voltage is in range 44 V-57 V if intend to use PoE/PoE+" ILPOWER-5-CLR_OVERDRAWN 5-Notice Interface [chars] is NOT overdrawing power. it is consuming [dec] milliwatts where as maximum configured value is [dec] milliwatts. - inline-power LOG_STD_NO_ACTION ILPOWER-5-CLR_OVERDRAWN 5-Notice Interface [chars] is NOT overdrawing power. it is consuming [dec] milliwatts where as maximum configured value is [dec] milliwatts. - inline-power LOG_STD_NO_ACTION ILPOWER-5-DET_SHORT_SPARE_PAIR 5-Notice Interface [chars]: spare pair short detected spare pair short detect error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-DET_SHORT_SPARE_PAIR 5-Notice Interface [chars]: spare pair short detected spare pair short detect error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-DET_TIMEOUT_SPARE_PAIR 5-Notice Interface [chars]: spare pair detect timeout spare pair timeout detect error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-DET_TIMEOUT_SPARE_PAIR 5-Notice Interface [chars]: spare pair detect timeout spare pair timeout detect error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-DETECT 5-Notice Interface [chars]: Power Device detected: [chars] The switch has detected the attached power device. inline-power LOG_STD_NO_ACTION ILPOWER-5-IEEE_DISCONNECT 5-Notice Interface [chars]: PD removed The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-IEEE_DISCONNECT 5-Notice Interface [chars]: PD removed The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-ILPOWER_POWER_CDP_SHUT 5-Notice Interface [chars]: inline power shut - inline-power LOG_STD_NO_ACTION ILPOWER-5-ILPOWER_POWER_CDP_SHUT 5-Notice Interface [chars]: inline power shut - inline-power LOG_STD_NO_ACTION ILPOWER-5-ILPOWER_POWER_DENY 5-Notice Interface [chars]: inline power denied. Reason: [chars] There is not enough power remaining in the switch to supply to\n\ the Power over Ethernet PoE port. inline-power LOG_STD_NO_ACTION ILPOWER-5-ILPOWER_POWER_DENY 5-Notice Interface [chars]: inline power denied. Reason: [chars] There is not enough power remaining in the switch to supply to\n\ the Power over Ethernet PoE port. inline-power LOG_STD_NO_ACTION ILPOWER-5-IMAX_SPARE_PAIR 5-Notice Interface [chars]: spare pair power error: IMAX spare pair imax error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-INVALID_IEEE_CLASS 5-Notice Interface [chars]: has detected invalid IEEE class: [dec] device. Power denied The power device has invalid IEEE class. switch won't power\n\up the device - LOG_STD_NO_ACTION ILPOWER-5-INVALID_IEEE_CLASS 5-Notice Interface [chars]: has detected invalid IEEE class: [dec] device. Power denied The power device has invalid IEEE class. switch won't power\n\up the device - LOG_STD_NO_ACTION ILPOWER-5-LINKDOWN_DISCONNECT 5-Notice Interface [chars]: Link down disconnect The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-LINKDOWN_DISCONNECT 5-Notice Interface [chars]: Link down disconnect The powered device is no longer connected to the\n\ switch or the connected powered device is being powered by an\n\ external AC power source. The switch is no longer providing power on\n\ the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-LLDP_SHUTDOWN 5-Notice Interface [chars]: PD requested shutdown for [dec] sec via LLDP MDI TLV Inline power is removed because \n\ PD requested shutdown via LLDP MDI TLV inline-power LOG_STD_NO_ACTION ILPOWER-5-PD_ENTRY_REMOVAL 5-Notice Interface [chars]: power device entry removed admin_state=[chars] oper_state=[chars] received power device removal event from controller inline-power LOG_STD_NO_ACTION ILPOWER-5-PD_POWER_DEMOTE 5-Notice Interface [chars] requested power=[dec]w hardware limit=[dec]w Requested power is greater than the hardware limit inline-power LOG_STD_NO_ACTION ILPOWER-5-PGOOD_TIMEOUT_SPARE_PAIR 5-Notice Interface [chars]: spare pair power good timeout error spare pair power good timeout error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-PGOOD_TIMEOUT_SPARE_PAIR 5-Notice Interface [chars]: spare pair power good timeout error spare pair power good timeout error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-POLICE_POWER_INVALID 5-Notice Interface [chars]: invalid power police [dec] milliwatts current [dec] mA voltage [dec] mV power policing current or voltage value is invalid. - LOG_STD_SH_TECH_ACTION ILPOWER-5-POLICE_POWER_INVALID 5-Notice Interface [chars]: invalid power police [dec] milliwatts current [dec] mA voltage [dec] mV power policing current or voltage value is invalid. - LOG_STD_SH_TECH_ACTION ILPOWER-5-POWER_GRANTED 5-Notice Interface [chars]: Power granted There is enough power available in the switch and\n\ the switch is providing power on the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-POWER_GRANTED 5-Notice Interface [chars]: Power granted There is enough power available in the switch and\n\ the switch is providing power on the interface. inline-power LOG_STD_NO_ACTION ILPOWER-5-PWRGOOD_SPARE_PAIR 5-Notice Interface [chars]: spare pair power good Spare pair power request was successful and power is available on spare pair inline-power LOG_STD_NO_ACTION ILPOWER-5-PWRGOOD_SPARE_PAIR 5-Notice Interface [chars]: spare pair power good Spare pair power request was successful and power is available on spare pair inline-power LOG_STD_NO_ACTION ILPOWER-5-SENSE_POWER_INVALID 5-Notice Interface [chars]: invalid power sense [dec] milliwatts current [dec] mA voltage [dec] mV power sensing current or voltage value is invalid. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-5-SENSE_POWER_INVALID 5-Notice Interface [chars]: invalid power sense [dec] milliwatts current [dec] mA voltage [dec] mV power sensing current or voltage value is invalid. inline-power LOG_STD_SH_TECH_ACTION ILPOWER-5-SINGLE_PAIRSET_FAULT 5-Notice Interface [chars]: shutting down [chars] pairset due to [chars] fault The dual signature PD on this port has hit a critcal fault on one pairset and hence that pairset will be shutdown inline-power LOG_STD_NO_ACTION ILPOWER-5-TSTART_SPARE_PAIR 5-Notice Interface [chars]: spare pair power error: TSTART spare pair tstart error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-5-TSTART_SPARE_PAIR 5-Notice Interface [chars]: spare pair power error: TSTART spare pair tstart error has occurred power on spare pair will not be supplied inline-power LOG_STD_NO_ACTION ILPOWER-6-SET_ILPOWER 6-Information Set power allocated to POE to [dec] for slot [dec] The power allocated to POE has changed inline-power LOG_STD_NO_ACTION ILPOWER-7-DETECT 7-Debug Interface [chars]: Power Device detected: [chars] The switch has detected the attached power device. inline-power LOG_STD_NO_ACTION IM_EEPROM-3-FIELD_NOT_FOUND 3-Error [chars]: Failed to find content of field type 0x[hec] with data size = [dec] bytes. The EEPROM might require an update. System failed to find the content of the indicated field type from the IM EEPROM. The format of the EEPROM of the indicated IM might not be up to date. spa-infra SPA_EEPROM_STD_BUG_ACTION IM_EEPROM-3-FORMAT_ERROR 3-Error [chars]: [chars]. The EEPROM might require an update. A format error has been detected in the EEPROM of the indicated IM. The type of error is indicated in the error message. asr900-im SPA_EEPROM_STD_BUG_ACTION IM-3-UNSUPPORTED_DATA 3-Error Data conversion error [chars] 0x%X An internal software error has occured when converting the data specified in the message from one representation to another. asr900-im LOG_STD_SH_TECH_ACTION IMAP_ALG-3-CHUNK_CREATE_FAIL 3-Error - IMAP code has detected a cleartext logon attempt in the inspected IMAP connection while secure-login is configured. This command has been rejected. cpp-ucode "This message is for informational purposed only but may indicate" "a security problem." IMPOSITION_DISABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - IMPOSITION_DISABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - IMPOSITION_ENABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - IMPOSITION_ENABLED-5-ATOM_TRANS 5-Notice ERRMSG_NOFLAGS - - - IMSP_ACLMGR-2-NOMEM 2-Critical [chars]. Out of memory System is out of Memory imsp-acl LOG_STD_ACTION IMSP_ACLMGR-2-NOVMR 2-Critical Cannot generate hardware representation of access list [chars] There were insufficient resources available for generating a hardware representation of the access list. Either lack of available logical operation units or lack of memory can cause this problem. Logical operation units are needed when a match on TCP flags is specified or when any test other than eq that is: ne gt lt or range is firmware "Modify the ACL configuration to use fewer resources." IMSP_ACLMGR-3-INVALIDACL 3-Error [chars] failed Addition/Deletion Failed imsp-acl LOG_STD_ACTION IMSP_ACLMGR-3-INVALIDPARAM 3-Error Invalid [chars] [dec] encountered ACL Manager has encountered an invalid parameter value. firmware "show running-config" IMSP_ACLMGR-3-MAXACE 3-Error MAX ACE count [dec] exceeded No. ACEs configured is beyond limit imsp-acls LOG_STD_ACTION IMSP_ACLMGR-3-UNKNOWNACTION 3-Error Unknown VMR access group action 0x[hec] An internal software error has occurred. firmware LOG_STD_ACTION IMSP_ACLMGR-3-UNKNOWNL4OPERATION 3-Error Unknown L4 operation 0x[hec] ACL Manager module received invalid value for L4 operation. The problem can be due to memory corruption or bad system memory. firmware IMSP_ACL_L4OP_ERROR IMSP_ACLMGR-4-ACLTCAMFULL 4-Warning [chars]ACL TCAM Full. Software Forwarding packets on The ACL configuration is too large to fit in the platform -specific ACL TCAM table. firmware "Simplify the ACLs applied to interfaces or reduce" " their number." IMSP_CTS-3-SGACL_PROGRAM_ERR 3-Error Unable to [chars] SGACLs for sgt [dec] dgt [dec] with reason [chars] An unexpected condition has occurred while programming SGACL petra-cts "Reconfigure the SGACL" IMSP_CTS-3-SGT_PROGRAM_ERR 3-Error [chars] binding [chars] failed for [chars] with reason [chars]\n An unexpected condition has occurred while programming IP SGT - "Reconfigure the IP SGT binding" IMSP_CTS-6-INVALID_ACE 6-Information Platform can suppor match only ip protocol tcp/udp src or dst port Invalid match criteria - "Remove one or more entries from ACES\n" IMSP_CTS-6-SGACL_POLICIES 6-Information Platform can not support more than [dec] ACEs per cell. SGACL policy entries limit exceeded - "Remove one or more entries from ACES\n" IMSP_CTS-6-SGACL_TABLE_FULL 6-Information Platform can not support more than [dec] SGT/DGT pairs SGACL table resource full - "Remove SGACL\n" IMSP_CTS-6-SGT_TABLE_FULL 6-Information Platform can not support more than [dec] [chars] bindings IP/SUBNET SGT table resource full - "Remove SGT binding\n" IMSP_EPM-3-EPM_ACE_MAX_CROSS 3-Error EPM - Reached max ace limit255 An unexpected condition has occurred since max ACE limit reached l2security "Correct the config which can have max of 255 ACEs\ per port" IMSP_IPSG-3-IPSG_ADDRS_FULL 3-Error IPSG Platform Address list is null An unexpected condition has occurred which is due to the absence of\n\ resource available in IPSG address list l2security "Correct the config which can have max of 254 IP address" INBAND_or_EOBC-3-INVALID_SEND 3-Error Invalid send operation packet on [chars] Internal error caused illegal call to device driver:normal operation continues msfc2 LOG_STD_RECUR_ACTION INBAND-3-BAD_PAK 3-Error Possibly un-encapsulated packet passed to Mistral: int [chars] type [dec] stat 0x[hec] flags 0x[hec] size [dec] offset [dec] requeue_token [dec] r1 [dec] r2 [dec] total detected [dec] Badly encapsulated packet from process level msfc2 LOG_STD_ACTION INBAND-3-INV_TX_PACKET 3-Error [chars]: packet neither on IBL nor on OBL The packet to be transmitted is neither on the IBL nor on the OBL:normal operation continues msfc2 LOG_STD_RECUR_ACTION INBAND-3-INVALID_PAK 3-Error Sent from [chars] with invalid [chars] of [dec] bytes with source vlan:[dec] and packetsize:[dec] Badly formed packet in inband fastpath or process level msfc2 LOG_STD_ACTION INBAND-3-NOBUF 3-Error Dropping the packet. The system controller receive buffer pool has been exhausted. No further input packets can be handled until some buffers are returned to the pool:normal operation continues msfc2 LOG_STD_RECUR_ACTION INBAND-6-BAD_IDB 6-Information Bad idb for vector [chars]: [chars] vlan [dec] total [dec] Bad idb returned from get_l3_swidb msfc2 LOG_STD_RECUR_ACTION INDXOBJ-3-ADD_ERROR 3-Error index add for [chars] failed: [chars] index object routine error - LOG_STD_ACTION INDXOBJ-3-ADD_ERROR 3-Error index add for [chars] failed: [chars] index object routine error - LOG_STD_ACTION INDXOBJ-3-INTERRUPT 3-Error index object routine [chars] called from interrupt context inappropriate index object routine called from interrupt routine. - LOG_STD_ACTION INDXOBJ-3-INTERRUPT 3-Error index object routine [chars] called from interrupt context inappropriate index object routine called from interrupt routine. - LOG_STD_ACTION INFO-5-LDP 5-Notice ERRMSG_NOFLAGS - - - INFO-5-LDP 5-Notice ERRMSG_NOFLAGS - - - INFO-6-OF_AGENT 6-Information ERRMSG_NOFLAGS - - - INFO-6-OF_AGENT 6-Information ERRMSG_NOFLAGS - - - INFO-6-OVS 6-Information ERRMSG_NOFLAGS - - - INFO-6-OVS 6-Information ERRMSG_NOFLAGS - - - INFRA_ARL-3-BAD_ART_ID 3-Error art_id=[hec] An internal error occurred cpp-ucode LOG_STD_ACTION INFRA_STATS-3-OUT_OF_RANGE 3-Error [chars] [dec] out of max size [dec] STATS work improperly Data invalid from DMA cmts-application LOG_STD_RECUR_ACTION INFRA_STATS-3-OUT_OF_SHMEM 3-Error out of max size [dec] start %p curloc %p type [dec] len [dec] next %lld Data invalid from NONDMA cmts-application LOG_STD_RECUR_ACTION INFRA_STATS-4-PROCESS_OVERTIME 4-Warning NON_DMA has been processing for [dec]ms check if CPU high Process NONDMA Stats overtime it is probably related to CPU high utilization. It is normal to see a small amount of it right after LCHA with scale modems due to low priority of this process and high CPU cmts-application LOG_STD_RECUR_ACTION INFRA-3-INVALID_GPM_ACCESS 3-Error Invalid GPM [chars] at [hec] HAL start [hec] HAL end [hec] INFRA start [hec] INFRA [hec] NET [hec] Processing packet went beyond valid packet data packet was possibly invalid ppe info and encrypted pkt dump follow cpp-ucode LOG_STD_ACTION INFRA-3-INVALID_GPM_ACCESS 3-Error Invalid GPM [chars] at [hec] HAL start [hec] HAL end [hec] INFRA start [hec] INFRA [hec] NET [hec] Processing packet went beyond valid packet data packet was possibly invalid ppe info and encrypted pkt dump follow cpp-ucode LOG_STD_ACTION INFRA-3-INVALID_GPM_ACCESS_DATA 3-Error - Packet associated with previous exception error The packet data has been encrypted cpp-ucode LOG_STD_ACTION INFRA-3-INVALID_GPM_ACCESS_DATA 3-Error - Packet associated with previous exception error The packet data has been encrypted cpp-ucode LOG_STD_ACTION INFRA-3-INVALID_GPM_ACCESS_INFO 3-Error %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x Registers associated with previous exception error - LOG_STD_ACTION INFRA-3-INVALID_GPM_ACCESS_INFO 3-Error %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x %08x Registers associated with previous exception error - LOG_STD_ACTION INFRA-3-L0I_FETCH_ERROR 3-Error thread=[dec] PC=0x[hec] Level-0 instruction cache fetch error possibly recoverable cpp-ucode LOG_STD_ACTION INFRA-3-L1L2_ICACHE_ERROR 3-Error thread=[dec] reg=[chars] addr=0x%llx val=0x[hec] L1/L2 ICACHE error possibly recoverable cpp-ucode LOG_STD_ACTION INIT_FAIL-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - INIT_FAIL-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - INIT_TAG_ALLOC-4-LCON 4-Warning ERRMSG_NOFLAGS - - - INIT_TAG_ALLOC-4-LCON 4-Warning ERRMSG_NOFLAGS - - - INIT-3-LCON 3-Error ERRMSG_NOFLAGS - - - INIT-3-LCON 3-Error ERRMSG_NOFLAGS - - - INIT-3-LDP 3-Error ERRMSG_NOFLAGS - - - INIT-3-LDP 3-Error ERRMSG_NOFLAGS - - - INIT-3-LDPLIB 3-Error ERRMSG_NOFLAGS - - - INIT-3-LDPLIB 3-Error ERRMSG_NOFLAGS - - - INIT-3-MPLS_TE_PCALC 3-Error ERRMSG_FLAG_TRACEBACK - - - INIT-3-MPLS_TE_PCALC 3-Error ERRMSG_FLAG_TRACEBACK - - - INTERCHASSIS_REDUNDANCY-4-STDBY_PRESENT 4-Warning Removal of standby RP in location [chars] is recommended for inter-chassis redundancy configuration Removal of standby RP from the chassis is recommended for inter-chassis redundancy iosxe-b2b-ha LOG_STD_ACTION INTERFACE_API-1-NAMESTRTOOLONG 1-Alert Interface name [chars].[dec] exceeded maximum allowed length [dec] An internal software error occurred. idb LOG_STD_ACTION INTERFACE_API-1-NAMESTRTOOLONG 1-Alert Interface name [chars].[dec] exceeded maximum allowed length [dec] An internal software error occurred. idb LOG_STD_ACTION INTERFACE_API-1-NOMORE_HASWIDBS 1-Alert No more IDBS can be created. \nThe maximum allowed numbers [dec] has been reached on Standby \nPlease force redundancy mode to RPR if full Active Capacity [dec] is needed No more Software IDB numbers can be Created. The maximum allowed numbers has been reached for this High Available System.\n idb - INTERFACE_API-1-NOMORE_HASWIDBS 1-Alert No more IDBS can be created. \nThe maximum allowed numbers [dec] has been reached on Standby \nPlease force redundancy mode to RPR if full Active Capacity [dec] is needed No more Software IDB numbers can be Created. The maximum allowed numbers has been reached for this High Available System.\n idb - INTERFACE_API-1-NOMOREHWIDBNUMBERS 1-Alert No more hardware IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n No more hardware IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n idb "In addition to the following copy the information " "from show idb. " LOG_STD_ACTION INTERFACE_API-1-NOMOREHWIDBNUMBERS 1-Alert No more hardware IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n No more hardware IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n idb "In addition to the following copy the information " "from show idb. " LOG_STD_ACTION INTERFACE_API-1-NOMORESWIDB 1-Alert No more SWIDB can be allocated maximum allowed [dec] No more Interfaces can be created because the maximum number \n\ of SWIDB allowed for this platform has been reached Obtain from traceback. LOG_STD_ACTION INTERFACE_API-1-NOMORESWIDB 1-Alert No more SWIDB can be allocated maximum allowed [dec] No more Interfaces can be created because the maximum number \n\ of SWIDB allowed for this platform has been reached Obtain from traceback. LOG_STD_ACTION INTERFACE_API-1-NOMORESWIDBNUMBERS 1-Alert No more software IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n No more software IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n idb "In addition to the following copy the information " "from show idb. " LOG_STD_ACTION INTERFACE_API-1-NOMORESWIDBNUMBERS 1-Alert No more software IDB numbers can be issued. The maximum allowed numbers [dec] has been reached for this platform.\n No more software IDB numbers can be issued. The maximum allowed numbers has been reached for this platform.\n idb "In addition to the following copy the information " "from show idb. " LOG_STD_ACTION INTERFACE_API-3-BADIDBSTATUSCHANGECALL 3-Error Invalid function call at interrupt level. An internal function was illegally called at interrupt level. This error might be caused by incorrectly coded creation or deletion of an interface or during an OIR operation.\n idb "Perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance copy the error message " "exactly as it appears on the console or in the system log. " "Issue the show tech command and copy the " "output. If you performed any actions before the error message " "appeared make a note of this. Open a case with the Technical " "Assistance Center via the Internet " TAC_CASE_OPEN " or contact " "your Cisco technical support representative and provide the " "representative with the gathered information." INTERFACE_API-3-BADIDBSTATUSCHANGECALL 3-Error Invalid function call at interrupt level. An internal function was illegally called at interrupt level. This error might be caused by incorrectly coded creation or deletion of an interface or during an OIR operation.\n idb "Perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance copy the error message " "exactly as it appears on the console or in the system log. " "Issue the show tech command and copy the " "output. If you performed any actions before the error message " "appeared make a note of this. Open a case with the Technical " "Assistance Center via the Internet " TAC_CASE_OPEN " or contact " "your Cisco technical support representative and provide the " "representative with the gathered information." INTERFACE_API-3-CANNOTGETMTU 3-Error Error [dec] received while getting MTU: [chars]. Using default [dec] A software error has occurred while attempting to retrieve the MTU value from the interface. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-CANNOTGETMTU 3-Error Error [dec] received while getting MTU: [chars]. Using default [dec] A software error has occurred while attempting to retrieve the MTU value from the interface. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-HWIDBQREENTRANT 3-Error [chars] in progress of being inserted/removed ignoring new request to [chars] A software error has occurred while attempting to insert or remove the interface into the system as there's already another attempt in progress to insert or remove this interface. The first attempt must complete before a new attempt can be started. The user should retry this operation at a later time. idb LOG_STD_ACTION INTERFACE_API-3-HWIDBQREENTRANT 3-Error [chars] in progress of being inserted/removed ignoring new request to [chars] A software error has occurred while attempting to insert or remove the interface into the system as there's already another attempt in progress to insert or remove this interface. The first attempt must complete before a new attempt can be started. The user should retry this operation at a later time. idb LOG_STD_ACTION INTERFACE_API-3-IFNUMTOIDBERROR 3-Error Error occurred while using the ifnum to idb table for interface [chars] if number [dec] during [chars] A software error has occurred. This message is displayed when an operation on the if_number to idb mapping table could not be performed successfully. idb LOG_STD_ACTION INTERFACE_API-3-IFNUMTOIDBERROR 3-Error Error occurred while using the ifnum to idb table for interface [chars] if number [dec] during [chars] A software error has occurred. This message is displayed when an operation on the if_number to idb mapping table could not be performed successfully. idb LOG_STD_ACTION INTERFACE_API-3-INVALIDSUBBLOCKPARAMETERS 3-Error Invalid subblock parameters for [chars] were supplied. An internal software error occurred. idb "Copy the error message exactly as it appears on the console or in " "the system log. Issue the show idb and show tech-support " "commands to gather data that may help identify the nature of " "the error. Also perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance open a case with the " "Technical Assistance Center via the Internet " TAC_CASE_OPEN " or contact your Cisco technical support representative and " "provide the representative with the gathered information." INTERFACE_API-3-INVALIDSUBBLOCKPARAMETERS 3-Error Invalid subblock parameters for [chars] were supplied. An internal software error occurred. idb "Copy the error message exactly as it appears on the console or in " "the system log. Issue the show idb and show tech-support " "commands to gather data that may help identify the nature of " "the error. Also perform a search of the Bug Toolkit " BUG_TOOLKIT "." "If you still require assistance open a case with the " "Technical Assistance Center via the Internet " TAC_CASE_OPEN " or contact your Cisco technical support representative and " "provide the representative with the gathered information." INTERFACE_API-3-NOADDSUBBLOCK 3-Error The [chars] subblock named [chars] was not added to [chars] A software error has occured this message is displayed when IDB subblocks cannot be added. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-NOADDSUBBLOCK 3-Error The [chars] subblock named [chars] was not added to [chars] A software error has occured this message is displayed when IDB subblocks cannot be added. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-NODESTROYSUBBLOCK 3-Error The [chars] subblock named [chars] was not removed A software error has occured this message is displayed when \n\ IDB subblocks cannot be removed. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-NODESTROYSUBBLOCK 3-Error The [chars] subblock named [chars] was not removed A software error has occured this message is displayed when \n\ IDB subblocks cannot be removed. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-NOSUBBLOCK 3-Error [chars] subblock does not exist on interface [chars] An internal software error occurred. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-NOSUBBLOCK 3-Error [chars] subblock does not exist on interface [chars] An internal software error occurred. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-SUBNUMDBERR 3-Error subnum [hec] error in [chars] A software error has occured this message is displayed when a problem has occured with a sub_number db. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-3-SUBNUMDBERR 3-Error subnum [hec] error in [chars] A software error has occured this message is displayed when a problem has occured with a sub_number db. Obtain from traceback. LOG_STD_ACTION INTERFACE_API-4-BADPAKINPUT 4-Warning pak->if_input is not initialized An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-BADPAKINPUT 4-Warning pak->if_input is not initialized An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-BADPAKOUTPUT 4-Warning pak->if_output is not initialized on interface [chars] An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-BADPAKOUTPUT 4-Warning pak->if_output is not initialized on interface [chars] An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-BADPOINTER 4-Warning Function [chars] detected an invalid [chars] pointer of %08lX ignoring A software error has occurred this message is displayed when \n\ an invalid pointer is detected. Obtain from traceback. "LOG_STD_SH_TECH_ACTION" INTERFACE_API-4-BADPOINTER 4-Warning Function [chars] detected an invalid [chars] pointer of %08lX ignoring A software error has occurred this message is displayed when \n\ an invalid pointer is detected. Obtain from traceback. "LOG_STD_SH_TECH_ACTION" INTERFACE_API-4-BADSWIDB 4-Warning [chars] may not be referencing the correct swidb An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-BADSWIDB 4-Warning [chars] may not be referencing the correct swidb An internal software error occurred. Obtain from traceback. LOG_STD_RECUR_ACTION INTERFACE_API-4-TBLERROR 4-Warning A error occurred while using the Index Table utility for [chars]. - Obtain from traceback. LOG_STD_ACTION INTERFACE_API-4-TBLERROR 4-Warning A error occurred while using the Index Table utility for [chars]. - Obtain from traceback. LOG_STD_ACTION Interface [chars]: [chars] The CHOCX RP driver queries the LC for SONET information the LC didn't reply. c7600-sip-200 "This is a internal software error. Decode the " "traceback. Enable debug hw-module subslot " "/ command. Check Bug Toolkit " "before calling the TAC. When calling the TAC " "please provide the above information along with the " "output of show logging and the " "output of show tech/ oir power-cycle The Firmware version on this Linecard is not supported by the Software. POE is not functional on this line card The linecard should be power-cycled to recover from this issue. iomd IOMD_POE_FW_MISMATCH_ACTION IOMD-2-POE_INIT_FAIL 2-Critical [chars] on Slot [dec] Subslot [dec]. POE functionality will not work on this LC A failure occurred during initialization of LC for POE. POE is not functional on the line card that generated the message. iomd IOMD_STD_ACTION IOMD-2-POE_RW_FAIL 2-Critical [chars] on Slot [dec] Subslot [dec]. POE functionality will not continue to work on this LC A failure occurred during read/write of POE registers from HW. POE is not functional on the line card that generated the message. iomd IOMD_STD_ACTION IOMD-2-TIMERFAIL_CXT 2-Critical IOMD timer context error A failure occurred during context retrieval for a timer iomd IOMD_AUTO_RECOVERY_ACTION IOMD-3-CREATE_TDLH_FAILURE 3-Error Failed to create SPA [dec]/[dec] handle Failed to create message handle for SPA communication. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-CREATE_TDLMSG_FAILURE 3-Error Failed to create [chars] message for [chars]. Failed to create/allocate necessary TDL message for SPA communication. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-DISPATCH_INIT_TDLH_FAILURE 3-Error Failed to initialize dispatch path for SPA [dec]/[dec] handle Failed to initialize dispatch path handle for SPA communication. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-DOMAIN_TDLH_FAILURE 3-Error [chars] rc = [dec] Failed to bind message handle for SPA communication. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-HAIPC_FAIL 3-Error Failed to [chars] reason: [chars]. Failure in handling IOMD HA IPC. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-HARFROLE_FAIL 3-Error Failed to [chars]. Failure to establish start client or server. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-INVALID_HANDLE 3-Error Failed to get a valid IPC handle for type [dec] slot [dec] subslot [dec]. The client handle was found to be NULL for the given type/slot/subslot. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-INVALID_SLOT_NUM 3-Error slot= [dec] max slot = [dec] An invalid slot number is specified in one of the internal APIs. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-INVALID_SUBSLOT_NUM 3-Error subslot= [dec] max subslot = [dec] An invalid subslot number is specified in one of the internal APIs. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-INVALID_TDL_CCAPI_USAGE 3-Error - Incorrect usage of an internal API that should only be used on CC. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The SPA failed to allocate a buffer for communication with\n\ the Route Processor ASR1000-RP. asr900-im "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOMD-3-ISR_RC_ERROR 3-Error ISR return code out of range. rc=[dec] The ISR error return code is out of range. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-MARSHAL_ERR 3-Error Failed to marshal [chars]. Failure to marshal tdl message asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-MESSAGE_ERROR 3-Error Bay [dec]: [chars] An unexpected error has occurred. asr900-im "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOMD-3-MODULE_MESSAGE 3-Error [chars] An error is detected by the firmware running on the module in the slot and subslot specified in the message esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-3-NEBS_ACCESS_PID_FAIL 3-Error Failed to acess NGIO PID list for [chars] on slot/bay [dec]/[dec] in NEBS mode The access to NGIO PID list failed in NEBS mode and module will not be powered on esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-3-NRU_OIR_DRAIN_FAIL 3-Error NRU OIR EPF Fifo drain failed for mac [dec] on slot [dec] A failure occurred during NRU OIR EPF Fifo drain. NRU datapath may not functional. iomd IOMD_STD_ACTION IOMD-3-QUEUE_FAIL 3-Error Failed to dequeue because [chars]. Failure to handle events in queue. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-RFROLE_FAIL 3-Error Failed to update IM role for reason: [chars] Failure to handle role update. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-SETUP_TDLH_FAILURE 3-Error Failed to set the alloc/free handler for SPA [dec]/[dec] handle Failed to set the alloc/free handler for SPA communication. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-SIGBUS_ERROR 3-Error SIGBUS received for IM in slot: [dec] SIGBUS error encountered for IM asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-TIMER_FAIL 3-Error Failed to [chars]. Failure in timer processing. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-UNSUPPORTED_DATA 3-Error Data conversion error [chars] 0x%X An internal software error has occured when converting the data specified in the message from one representation to another. asr900-im LOG_STD_SH_TECH_ACTION IOMD-3-UNSUPPORTED_LEGACY_SWITCH 3-Error The previous generation switch module [chars] in slot [dec] bay [dec] is not compatible with current next-gen switching mode Legacy and next-gen switch modules have different feature set and cli behaviors which require system to determine corresponding switching mode at system boot time. Current mode selection is to check whether next-gen switch module locates in the chassis at boot time if yes system will come up in ngswitch mode otherwise in legacy mode. Users need to reload system to change system switching mode if it is neccessary esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-3-UNSUPPORTED_MODULE 3-Error The module [chars] in slot [dec] bay [dec] is not supported on this platform The module inserted is not supported on this platform and will not be powered on esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-3-UNSUPPORTED_MODULE_IN_NEBS 3-Error The module [chars] in slot [dec] bay [dec] is not supported in NEBS mode The module inserted is not supported in NEBS mode and will not be powered on esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-3-UNSUPPORTED_NGSWITCH 3-Error The next-gen switch module [chars] in slot [dec] bay [dec] needs a system reload to take effect because current system is in legacy switching mode Legacy and next-gen switch modules have different feature set and cli behaviors which require system to determine corresponding switching mode at system boot time. Current selection algorithm is to check whether next-gen switch module locates within chassis at boot time if yes system come up in ngswitch mode otherwise in legacy mode. Users need to reload system to change system switching mode. esg-io-infra LOG_STD_SH_TECH_ACTION IOMD-6-TDLMSG_INCOMPATIBLE 6-Information Failed to copy message [chars] to buffer not allowed for current domain. Failure to marshal a message indicates an incompatibility with the intended recipient. asr900-im LOG_STD_SH_TECH_ACTION IOS_LICENSE_IMAGE_APPLICATION-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_EVENT 3-Error [chars] The ios image licensing subsystem received an event which it does not understand or recognizes ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_EVENT 3-Error [chars] The ios image licensing subsystem received an event which it does not understand or recognizes ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_EVENT 3-Error [chars] The ios image licensing subsystem received an event which it does not understand or recognizes ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_VERSION 3-Error [chars] The ios image licensing subsystem received an event for an unknown version of a feature ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_VERSION 3-Error [chars] The ios image licensing subsystem received an event for an unknown version of a feature ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-3-UNKNOWN_VERSION 3-Error [chars] The ios image licensing subsystem received an event for an unknown version of a feature ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_CONFIG 6-Information EULA must be accepted for license level = [chars] This is an informational message to inform user that the user needs to reissue the command from an interactive terminal ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_CONFIG 6-Information EULA must be accepted for license level = [chars] This is an informational message to inform user that the user needs to reissue the command from an interactive terminal ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_CONFIG 6-Information EULA must be accepted for license level = [chars] This is an informational message to inform user that the user needs to reissue the command from an interactive terminal ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL 6-Information Module name = [chars] Next reboot level = [chars] and License = [chars] This is an informational message to display the change in the next reboot license level ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL 6-Information Module name = [chars] Next reboot level = [chars] and License = [chars] This is an informational message to display the change in the next reboot license level ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL 6-Information Module name = [chars] Next reboot level = [chars] and License = [chars] This is an informational message to display the change in the next reboot license level ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL_CONFIG 6-Information Please issue 'license boot' config command to make extension license [chars] available for use. This is an informational message to info user that to make extension license available to support image level licensing image level needs to be configured ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL_CONFIG 6-Information Please issue 'license boot' config command to make extension license [chars] available for use. This is an informational message to info user that to make extension license available to support image level licensing image level needs to be configured ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL_CONFIG 6-Information Please issue 'license boot' config command to make extension license [chars] available for use. This is an informational message to info user that to make extension license available to support image level licensing image level needs to be configured ios-licensing "This is an informational message no action is required" IOS_LICENSE_IMAGE_APPLICATION-6-NO_LICENSE 6-Information [chars] [chars]. There is no valid license available on the box and we are running on a default feature ios-licensing "please purchase a license to activate required features" IOS_LICENSE_IMAGE_APPLICATION-6-NO_LICENSE 6-Information [chars] [chars]. There is no valid license available on the box and we are running on a default feature ios-licensing "please purchase a license to activate required features" IOS_LICENSE_IMAGE_APPLICATION-6-NO_LICENSE 6-Information [chars] [chars]. There is no valid license available on the box and we are running on a default feature ios-licensing "please purchase a license to activate required features" IOS_LICENSE-2-NO_LICENSE 2-Critical No valid license avaiable to run any feature The Ios licensing subsystem could not get a valid license to run any feature on the box please purchase a license. ios-licensing "Purchase a valid license to run the features you requier on the " "box. You should contact the cisco portal or a TAC engineer to get " "a license. You can do a show license at the " "privileged command line prompt to get the list of availabe feature " "in the box " IOS_LICENSE-2-NO_LICENSE 2-Critical No valid license avaiable to run any feature The Ios licensing subsystem could not get a valid license to run any feature on the box please purchase a license. ios-licensing "Purchase a valid license to run the features you requier on the " "box. You should contact the cisco portal or a TAC engineer to get " "a license. You can do a show license at the " "privileged command line prompt to get the list of availabe feature " "in the box " IOS_LICENSE-2-NO_LICENSE 2-Critical No valid license avaiable to run any feature The Ios licensing subsystem could not get a valid license to run any feature on the box please purchase a license. ios-licensing "Purchase a valid license to run the features you requier on the " "box. You should contact the cisco portal or a TAC engineer to get " "a license. You can do a show license at the " "privileged command line prompt to get the list of availabe feature " "in the box " IOS_LICENSE-2-NO_MEM 2-Critical No memory available for [chars] The Ios licensing subsystem could not obtain the memory it needed. ios-licensing "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt." IOS_LICENSE-2-NO_MEM 2-Critical No memory available for [chars] The Ios licensing subsystem could not obtain the memory it needed. ios-licensing "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt." IOS_LICENSE-2-NO_MEM 2-Critical No memory available for [chars] The Ios licensing subsystem could not obtain the memory it needed. ios-licensing "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt." IOS_LICENSE-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-FAILED 3-Error [chars] The ios licensing subsystem failed to create a process/watched boolean etc to watch request from the remote show subsys license commands ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-IPC_FAILED 3-Error [chars] failed with an error = [chars] The ipc calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-IPC_FAILED 3-Error [chars] failed with an error = [chars] The ipc calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-IPC_FAILED 3-Error [chars] failed with an error = [chars] The ipc calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-RTTYS_FAILED 3-Error [chars] failed The rttys calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-RTTYS_FAILED 3-Error [chars] failed The rttys calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-RTTYS_FAILED 3-Error [chars] failed The rttys calls in the Ios licensing subsystem failed for some reason please capture the error msg and forward it to the appropriate licensing component ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-UNKNOWN_MSG_TYPE 3-Error an unknown message type was received dropping it msg_type = [dec] Ios licensing subsystem received a msg type which it does not recognizes or support ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-UNKNOWN_MSG_TYPE 3-Error an unknown message type was received dropping it msg_type = [dec] Ios licensing subsystem received a msg type which it does not recognizes or support ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOS_LICENSE-3-UNKNOWN_MSG_TYPE 3-Error an unknown message type was received dropping it msg_type = [dec] Ios licensing subsystem received a msg type which it does not recognizes or support ios-licensing "please capture the error msg and forward it to the appropriate licensing component" IOSD_INFRA-3-IFS_DEVICE_DETECT_FAIL 3-Error Device [chars] [chars] USB detection failed - "USB Insertion could not be handled completely." "Device needs to be removed and re-inserted" IOSD_INFRA-6-IFS_DEVICE_OIR 6-Information Device [chars] [chars] USB inserted/removed - LOG_STD_NO_ACTION IOSXE_APS-3-CCCONFIGFAILED 3-Error Pair config for interface [chars] Group [dec] failed Pair config for interface has failed iosxe-spa-pos LOG_STD_ACTION IOSXE_APS-3-CONFIG_FAIL 3-Error config change for interface [chars] Group [dec] failed config for an interface to forwarding plane has failed iosxe-spa-pos LOG_STD_ACTION IOSXE_APS-3-DOWNLOADFAIL 3-Error Unable to download [chars] message to [chars] An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the reported process. iosxe-spa-pos LOG_STD_ACTION IOSXE_APS-3-FLOWCONFIGTOCCFAILED 3-Error Flow id to cc for interface [chars] Group [dec] failed Flow id to cc for an interface has failed iosxe-spa-pos LOG_STD_ACTION IOSXE_APS-3-FLOWIDALLOCFAILED 3-Error Allocation of APS flow ID with manager failed for interface [chars] group [dec] An unexpected condition has occurred that allocation of\n\ APS flow ID. failed iosxe-spa-pos "show interface" IOSXE_APS-3-FLOWIDDELETIONFAILED 3-Error Deletion of APS flow ID with manager failed for interface [chars] group [dec] An unexpected condition has occurred that deletion of\n\ APS flow ID. iosxe-spa-pos "show interface" IOSXE_APS-3-GROUP_CONFIG_FAIL 3-Error Group change for interface [chars] Group [dec] failed Group change for interface has failed iosxe-spa-pos LOG_STD_ACTION IOSXE_APS-3-PAIR_CONFIG_FAIL 3-Error Pair config for interface [chars] Group [dec] failed Pair config for interface has failed iosxe-spa-pos LOG_STD_ACTION IOSXE_AUTHENTICATE-2-AUTHENTICATE_FAILED 2-Critical The platform authentication failed WDC authentication failed iosxe-csl "Check if WDC is programmed on this device" IOSXE_CCK-6-RUN_COMPLETED 6-Information Consistency Check for Run-Id [dec] is completed. Check 'show consistency-checker run-id [dec]'. Informational syslog indicating that consistency check has completed. iosxe-fwdmgr "show consistency-checker run-id " IOSXE_CIDB-3-ALLOC 3-Error Failed to allocate message for CIDB message When attempting to program the dataplane with a CIDB object there was not enough memory to allocate the message. iosxe-cidb LOG_STD_ACTION IOSXE_CIDB-3-MESSAGE 3-Error Failed to send message for CIDB object When the cidb object was being prepared to be sent to the data plane there was an error. iosxe-cidb LOG_STD_ACTION IOSXE_CRYPTOBW-3-CONF_FAILED 3-Error Configuration failed An error occurred when the crypto throughput configuration was attempted. iosxe-csl - IOSXE_CRYPTOBW-3-EULA_NOT_ACCEPTED 3-Error The EULA has to be accepted prior to crypto throughput configuration. Users need to accept EULA to activate the license iosxe-csl "Accept EULA for crypto throughput license" IOSXE_CRYPTOBW-3-INVALID_CONFIG 3-Error No valid license found for the configured crypto throughput level: [chars] kbps The boot up crypto throughput has been set to non-default level without having the valid license. iosxe-csl "Install valid crypto throughput license" IOSXE_CRYPTOBW-6-LEVEL 6-Information Crypto Throughput level has been set to [chars] bps Crypto Throughput level has been set to a number iosxe-csl - IOSXE_CRYPTOBW-6-RESET 6-Information Crypto Throughput level has been reset to default [chars] bps Crypto Throughput level has been reset iosxe-csl - IOSXE_CSLIFS-3-ERROR_SETTING 3-Error Error setting default file system [dec] There is an error happened after calling function ifs_set_default_directory iosxe-csl "Check the csl filesystem" IOSXE_CSLIFS-3-ERROR_SETTING 3-Error Error setting default file system [dec] There is an error happened after calling function ifs_set_default_directory iosxe-csl "Check the csl filesystem" IOSXE_CXSC-3-ACTION 3-Error Unknown proposition action [dec] - - - IOSXE_CXSC-3-ALLOC 3-Error Failed to allocate message for proposition When attempting to program the dataplane with a CXSC proposition object there was no enough memory to allocate the message. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-BAD_PROPOSITION 3-Error Proposition obj corrupt When the proposition was being sent to the data plane the object itself is corrupt. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-BAD_PROTOCOLPACK 3-Error Invalid Protocol Pack object When the Protocol Pack was being sent to the data plane the object's contents were invalid. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-BAD_SUMMARY 3-Error Summary obj corrupt When the proposition summary was being sent to the data plane the object itself is corrupt. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-FILESYSTEM_ERR 3-Error FileSystem Error [chars]: Unable to Copy File from Unable to copy the NBAR Protocol Pack File to the file system for subsequent loading. The system will revert to the previously loaded Protocol Pack. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-INSUFFICIENT_ALLOC_IOSXE_VER 3-Error Insufficent memory allocated for IOSXE version String The input IOSXE Version String has insufficient memory to hold the IOSXE Version. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-INSUFFICIENT_ALLOC_NBAR_VER 3-Error Insufficent memory allocated for NBAR Engine Version String The input NBAR Engine Version string has insufficient memory to hold the NBAR Engine Version. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-MESSAGE 3-Error Failed to send message for proposition When the proposition was being prepared for sending to the data plane there was an error. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-PLATFORM_TYPE 3-Error Unrecognised platform type. CPU ID [dec] The platform that the cxsc service is being installed on is not recognised. The most likely cause is that this platform is not supported. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-RF_INIT 3-Error Failed to initialize CXSC Redundancy Facility client An unexpected condition occurred where the CXSC Redundancy Facility failed to initialize. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-STATISTICS_ALLOCATION 3-Error Unable to allocate space for statistics During initialization there was failure in the allocation of the memory to gather the statistics. It is non fatal but after seeing this message the CXSC subsystem will not be able to gather statistics. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-3-STILE_ACTIVATE 3-Error Failed to activate NBAR classification: [dec] An unexpected condition occurred where the CXSC NBAR protocol classification failed to activate. iosxe-cxsc LOG_STD_ACTION IOSXE_CXSC-4-DUAL_RP_UNSUPPORTED 4-Warning Dual RPs are not supported in conjunction with CXSC CXSC is not supported in a dual RP environment. To resolve this warning either unconfigure CXSC or remove the redundant Route Processor. iosxe-cxsc LOG_STD_ACTION IOSXE_DNS-3-UPDATE_FAILED 3-Error Update resolv.conf vrf [chars] rc [dec] An unexpected condition has occurred while updating the DNS file iosxe-iosd-infra LOG_STD_ACTION IOSXE_DNS-3-VRF_FAILED 3-Error Operation [chars] on /etc/netns/[chars] rc [dec] An unexpected condition has occurred while updating the DNS directory iosxe-iosd-infra LOG_STD_ACTION IOSXE_DSP-3-ENQUEFAIL 3-Error Enqueue of TDL message failed [chars]. - - - IOSXE_EPA-3-ACT2_AUTHENTICATION_FAILURE 3-Error slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec]. ACT2 dev authentication Failed. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-AUTONEG_CFG_ERR 3-Error interface [chars] autoneg state '[chars]' is incompatible with transciever. Remove \'[chars]\' to allow the transceiver. Autoneg Config is not compatible. Remove autoneg config on the interface to allow the transceiver DDTS_COMPONENT "Remove the negotiation auto config or " "reinsert the previously enabled transceiver." IOSXE_EPA-3-CARD_PORT_NUM_FAILURE 3-Error Failure in getting card port number from spa port [dec] for EPA in [dec]/[dec] Failed to get card port number from spa port number DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-CREATION_FAILURE 3-Error slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec]. Failed to create a SPA object. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-EPA_PROHIBIT 3-Error Insertion of [chars] not allowed in [dec]/[dec] post-boot The SPA in the specified subslot cannot be inserted once the system boots up in controller mode - LOG_STD_NO_ACTION IOSXE_EPA-3-MAC_FAULT 3-Error MAC link on [chars] is down due to [chars] MAC fault reason local/remote fault DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_ALS_PTR 3-Error - Pointer to a als object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_DEVOBJ_PTR 3-Error - Pointer to a DEVOBJ object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_DEVPSEQ_PTR 3-Error - Pointer to a DEVPSEQ object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_DS_PTR 3-Error - Pointer to a ether instanace is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_EPA_MODE_SB_PTR 3-Error - Pointer to an EPA mode subblock is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_EPA_PORT_CFG_PTR 3-Error - Pointer to an epa port cfg is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_EPA_PTR 3-Error - Pointer to an EPA object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_EPASENSOR_PTR 3-Error - Pointer to a DEVSENSOR object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_FPGA_PTR 3-Error - Pointer to a FPGA object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_HWIDB_PTR 3-Error - Pointer to a HWIDB object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_PORT_PTR 3-Error - Pointer to a PORT object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_VFT 3-Error - Pointer to a DEVSENSOR object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-NULL_VSC_PHY_INFO_PTR 3-Error - Pointer to a VSC PHY INFO object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-SPA_PORT_NUM_FAILURE 3-Error Failure in getting spa port number from card port [dec] for EPA in [dec]/[dec] Failed to get spa port number from card port number DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_EPA-3-UNSUPPORTED_XCVR 3-Error Transceiver type [chars] is not allowed on spa [chars] port [dec] This transceiver is not allowed on the SPA DDTS_COMPONENT "Consult the documentation and ensure supported " "transceivers are plugged into the SPA" IOSXE_EPA-3-XCVR_EC_BWMISMATCH 3-Error Trasnsceiver bandwidth is incompatible with Port-channel[dec] allowed bandwidth. Remove \'channel-group [dec]\' config for interface [chars] to allow the transceiver The interface port into which the transceiver is inserted is part of a Port-channel. The Port-channel has member links whose bandwidth doesn't match with the inserted transceier's bandwidth. Since port-channel cannot allow heterogenous bandwidth links this transceiver is not allowed in to the port. DDTS_COMPONENT "Remove the channel-group config for the port where " "transceiver is inserted or insert a transceiver " "whose bandwidth is compatible with the port-channel " "bandwidth" IOSXE_EPA-3-XCVR_PROHIBIT 3-Error Transceiver is prohibited to come online for interface [chars] XCVR is prohibited on the interface DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_ETHERCHAN-3-LINK_MTU_FAIL 3-Error Failure in changing MTU of interface [chars] to port-channel [chars] MTU The MTU for the interface mentioned in the message cannot be changed to match the MTU configured on the port channel interface iosxe-fwdmgr "Remove the link mentioned in the message from " "the port-channel group" IOSXE_ETHERCHAN-6-LINK_MTU 6-Information Interface [chars] MTU set to port-channel [chars] MTU [dec] The MTU for the interface mentioned in the message is changed to match the MTU configured on the port channel interface - LOG_STD_NO_ACTION IOSXE_EWLC_LICENSE-2-MSGDEVICENOTREG 2-Critical Unregistered 9800-CL can only be used in lab. For production usage please register this device in [dec] days. Failure to do so will result in a limited number [dec] of Access Points being allowed post this. Device is required to be registered with license manager within the licensing period. ewlc-licensing LOG_STD_ACTION IOSXE_EZMENU-3-VIRT_SRVC_REGISTER 3-Error Failed to register '[chars]' with virtual service manager An unexpected error has occured while trying to register this virtual service with the virtual service manager. This has prevented the virtual service from being enabled/disabled. vman LOG_STD_ACTION IOSXE_FMANRP_ADJ-3-ENCSIZE 3-Error Invalid encap length [dec] which is larger than max allowed [dec] bytes An unexpected condition has occurred which is due to invalid\n\ adjacency encapsulation size being larger than the maximum value\n\ allowed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_ADJ-3-ENQUEFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_ADJ-3-NOADJ 3-Error Adjacency entry is null An unexpected condition has occurred which is due to the absence of\n\ an adjacency entry structure. iosxe-fwdmgr "show adjacency" IOSXE_FMANRP_ADJ-3-NOFIBHWIDB 3-Error FIB Interface [chars] is null An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure. iosxe-fwdmgr "show adj" IOSXE_FMANRP_CCE-3-CCE_CLASS_CREATE 3-Error Unable to create class [dec].[dec] An error occured when trying to create a class-map. iosxe-fwdmgr "show policy-map\n\ [type ]" IOSXE_FMANRP_CCE-3-CCE_FILTER_OVERFLOW 3-Error Filter list overflow at type [chars] An internal error occured when trying to build class-map information for one of the classes in a policy-map. iosxe-fwdmgr "show class-map \n\ [type ]" IOSXE_FMANRP_CCE-3-CCE_INVALID_FILTER_RELN 3-Error Invalid filter relation [dec] An internal error occured when trying to build class-map information for one of the classes in a policy-map. iosxe-fwdmgr "show policy-map \n\ [type ]" IOSXE_FMANRP_CCE-4-CCE_NESTED_CLASS_LIMIT 4-Warning Nested class [dec] layers cannot exceed 4 When configure nested classes as match statements \n\ the total levels of nested classes cannot exceed 4 layers iosxe-fwdmgr "show class-map [type\n\ ]" IOSXE_FMANRP_CCE-4-CCE_STACK_LIMIT 4-Warning Failed to create class [dec] filter list An operation to send a filter list to the forwarding \n\ processor for a particular class has failed due to a \n\ resource issue. This may imply that the notification was\n\ dropped. iosxe-fwdmgr "show class-map [type\n\ ]" IOSXE_FMANRP_CCK-4-FMANRP_INCONSISTENT 4-Warning Consistency Check for [chars] cannot be completed for all entries. Check 'show consistency-checker run-id [dec] detail'. Unexpected counts of updates happened during the CCK Run. iosxe-fwdmgr "show consistency-checker run-id " IOSXE_FMANRP_CEF-3-ENQUEFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_CEF-3-NOFIB 3-Error FIB entry is null An unexpected condition has occurred which is due to the absence of\n\ a FIB entry structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NOFIBIDB 3-Error FIB interface is null An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NOFIBPUSHCNT 3-Error FIB push counter is null An unexpected condition has occurred which is due to the absence of\n\ a FIB push counter structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NOFIBSB 3-Error FIB SB entry is null An unexpected condition has occurred which is due to the absence of\n\ a FIB SB entry structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NOFIBSIGNAL 3-Error FIB signal is null An unexpected condition has occurred which is due to the absence of\n\ a FIB signal structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NOFIBTABLE 3-Error FIB table is null An unexpected condition has occurred which is due to the absence of\n\ a FIB table structure. iosxe-fwdmgr "show ip cef" IOSXE_FMANRP_CEF-3-NONATADDR 3-Error NAT address is null An unexpected condition has occurred which is due to the absence of\n\ an NAT address. iosxe-fwdmgr "show ip alias" IOSXE_FMANRP_CEF-3-ROUTEMSGMARSHAL 3-Error Failed to copy route essage to IPC buffer for prefix [chars]/[dec] - [chars] This operation to build a TDL messages for route download has failed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_CEF-4-UPDFRAGSTATSERR 4-Warning Update IP Fragmentation statistics error An unexpected condition has occurred when updating fragmentation \n\ statistics iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_CEF-4-UPDREASSSTATSERR 4-Warning Update IP Reassembly statistics error An unexpected condition has occurred when updating reassembly \n\ statistics iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_CEF-4-UPDSTATSERR 4-Warning Update CEF statistics error An unexpected condition has occurred when updating cef statistics iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_EFP-3-EFP_ACCOUNTING_ERROR 3-Error [chars] FMAN EFP support has encounterd an EFP accounting error on [chars]: [chars] An inavlid EFP count found during EFP accouting in IOSXE FMAN EFP support. asr1k-evc show ethernet service instance detail IOSXE_FMANRP_EFP-3-EFP_AVL_DELETE 3-Error Failed to delete EFP node with id [dec] in [chars] An unexpected condition during configuration change asr1k-evc LOG_STD_ACTION IOSXE_FMANRP_EFP-3-EFP_CFM_ERROR 3-Error IOSXE FMAN EFP has encounterd an unsupported encap for CFM. Please remove any CFM configuration befor applying this encap. The encapuslation type is not supported for CFM on IOSXE. asr1k-ecfm "Remove any CFM config and reapply encapusation" IOSXE_FMANRP_EFP-3-INVALID_VALUE 3-Error Configuration specified invalid value [dec] for [chars] An unexpected condition in which configuration has accepted an invalid value. asr1k-evc LOG_STD_ACTION IOSXE_FMANRP_EOAM-3-IOSXE_FMANRP_EOAM_CONFIG 3-Error MIP Filtering enable/disable will take into affect only if it is applied before applying any cfm config. MIP filtering enable/disable should be applied before applying cfm config. Otherwise the command will have no affect on CFM Filtering. asr1k-ecfm "show platform software eoam fp active cfm global" IOSXE_FMANRP_ETHER_DPLB-3-INVALIDIF 3-Error Configuration specified invalid value [dec] for [chars] An non-existent interface is specified for ETHER_DPLB operation. iosxe-ether-dplb "show interface" IOSXE_FMANRP_ETHER_DPLB-3-IOSXE_FMANRP_ETHER_DPLB_STATS 3-Error Invalid stats update. type [dec] id [dec] An invalid stats update is received by ETHER_DPLB. iosxe-ether-dplb "show platform software ether_dplb" IOSXE_FMANRP_FPM-3-NOSTATUPDATE 3-Error Failed to update class-map statistics during periodic update A statistics update for a class-map has failed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_FPM-4-INVALIDACTION 4-Warning FPM feature action is invalid [dec] An unexpected condition has occurred which is due to the invalid\n\ action type when trying to bind FPM action with target class group. iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_FPM-4-INVALIDLENTYPE 4-Warning Field length type in PHDF file is invalid An unexpected condition has occurred which is due to the invalid\n\ field length type in PHDF file. iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_FPM-4-INVALIDMATCHTYPE 4-Warning FPM match type is invalid [dec] An unexpected condition has occurred which is due to the invalid\n\ FPM match type in one of FPM class-map filter match entry iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_IPHC-4-INVALIDSTATSTYPE 4-Warning IP header compression statistic message received has invalid stats type When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS the statistic type in that \n\ message is invalid. iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_IPHC-4-NOIDB 4-Warning IOS interface [chars] is not available for an IP header compression When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS one of data structures in IOS\n\ to store those IP header compression statistics is NULL iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_IPHC-4-STATSERR 4-Warning There is error when processing IP header compression statistic message received on IOS When receiving an IP header compression statistic update for an \n\ interface or sub-interface in IOS an unexpected error occurred iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_L2FIB-3-INVALIDIF 3-Error Configuration specified invalid value [dec] for [chars] An non-existent interface is specified for L2FIB operation. iosxe-l2fib "show interface" IOSXE_FMANRP_L2FIB-3-IOSXE_FMANRP_L2FIB_STATS 3-Error Invalid stats update. type [dec] id [dec] An invalid stats update is received by L2FIB. iosxe-l2fib "show platform software l2fib" IOSXE_FMANRP_LISP_SFLTR-3-UPDENTRYSTATSERR 3-Error Update LISP-SFLTR Entry statistics error An unexpected condition has occurred when updating lisp-sfltr entry statistics asr1k-lisp LOG_STD_ACTION IOSXE_FMANRP_LISP_SFLTR-3-UPDTABLESTATSERR 3-Error Update LISP-SFLTR Table statistics error An unexpected condition has occurred when updating lisp-sfltr table statistics asr1k-lisp LOG_STD_ACTION IOSXE_FMANRP_MACSEC-3-INVALIDIF 3-Error Configuration specified invalid value [dec] for [chars] An non-existent interface is specified for MACSEC operation. iosxe-macsec "show interface" IOSXE_FMANRP_MACSEC-3-IOSXE_FMANRP_MACSEC_STATS 3-Error Invalid stats update. type [dec] id [dec] An invalid stats update is received by MACSEC. iosxe-macsec "show platform software macsec" IOSXE_FMANRP_MCAST-3-FMANRP_BADMAF 3-Error Unknown Multicast AF [dec] An unexpected condition has occurred due to the download\n\ of an unknown MFIB address family code. iosxe-fwdmgr "show mfib" IOSXE_FMANRP_MCAST-3-FMANRP_DELID 3-Error Failed to remove Multicast ID [dec] An unexpected condition has occurred due to the failure\n\ to delete an internal identifier that is no longer in use. iosxe-fwdmgr "show mfib" IOSXE_FMANRP_MCAST-3-FMANRP_MCAP 3-Error Multicast Capability [chars]:[chars] error [chars] An unexpected condition has occurred due to the failure to set\n\ a multicast capability for this platform. iosxe-fwdmgr "show mfib state cap" IOSXE_FMANRP_MCAST-3-FMANRP_MSTATS 3-Error Can't process multicast stats upload from fman. type [dec] id [dec] An unexpected condition has occurred preventing interpretation\n\ of the stats message from the forwarding manager. This will\n\ prevent the statistics for the affected multicast entries from\n\ being updated. iosxe-fwdmgr "show ip mroute count" IOSXE_FMANRP_MCAST-3-FMANRP_NOID 3-Error No Multicast ID for [inet] [inet]/[dec] action [inet] - iosxe-fwdmgr "show ip mroute count" IOSXE_FMANRP_MCAST-3-FMANRP_UPDINTF 3-Error Failed to update flag count for [chars] due to [chars] An unexpected condition has occurred due to the failure\n\ to update the interface flag count iosxe-fwdmgr "show mfib" IOSXE_FMANRP_MCAST-3-MCASTID 3-Error Multicast ID management error An unexpected condition has occurred causing an internal\n\ ID to not be properly handled or disposed of iosxe-fwdmgr "show ip mroute count" IOSXE_FMANRP_OBJID2-3-DUPCREATE 3-Error Duplicate forwarding object creation obj_handle 0x[hec] type [dec] existing obj_id 0x[hec] type [dec] An unexpected condition has occurred which results in duplicate\n\ forwarding object creation with different object types. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_OBJID-5-DUPCREATE 5-Notice Duplicate forwarding object creation obj_handle 0x[hec] type [dec] existing obj_id 0x[hec] type [dec] An unexpected condition has occurred which results in duplicate\n\ forwarding object creation. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_RTMAP-3-INVALID_LIST 3-Error NULL An internal list structure has been detected as invalid. iosxe-pbr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_RTMAP-3-RTMAP_UNSUPPORTED 3-Error Routemap [chars] contain unsupported match/set clause ignored - - - IOSXE_FMANRP_RTMAP-3-RTMAPNULL 3-Error The route-map structure for [chars] is null An unexpected condition has occurred which is due to the absence of\n\ a route-map data structure. iosxe-fwdmgr "show route-map" IOSXE_FMANRP_RTMAP-4-UNKOWNCLIANT 4-Warning Unknown client type [dec] received An unexpected known client type is received for route-map download. iosxe-fwdmgr LOG_STD_SH_CMD_ACTION IOSXE_FMANRP_URPF-3-INVALIDIFHDL 3-Error Invalid interface handle [dec] for interface number= [dec] swidb= [hex] name= [chars] An unexpected condition has occurred which is due to an invalid \n\ interface handle iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP_URPF-4-NOV4SWIDB 4-Warning v4 sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a v4 swidb structure. iosxe-fwdmgr "show ip interface" IOSXE_FMANRP_URPF-4-NOV6SWIDB 4-Warning v6 sub-interface is null An unexpected condition has occurred which is due to the absence of\n\ a v6 swidb structure. iosxe-fwdmgr "show ipv6 interface" IOSXE_FMANRP_URPF-4-UPDV4STATSERR 4-Warning Update v4 URPF statistics error An unexpected condition has occurred when updating v4 URPF statistics iosxe-fwdmgr "show ip interface " IOSXE_FMANRP_URPF-4-UPDV6STATSERR 4-Warning Update v6 URPF statistics error An unexpected condition has occurred when updating v6 URPF statistics iosxe-fwdmgr "show ipv6 interface " IOSXE_FMANRP_VPLS-3-INVALID_VALUE 3-Error Invalid value for [chars] An unexpected condition in which an invalid value is get during VPLS configuration. iosxe-vpls LOG_STD_ACTION IOSXE_FMANRP_ZONES-3-NOSTATUPDATE 3-Error Failed to update zone-pair statistics during periodic update \n\ zone [chars] class [dec] A statistics update for a zone-pair has failed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-EPOCHTDLMSGMARSHAL 3-Error Failed to copy epoch TDL message to IPC buffer epoch number [dec] This operation to build a TDL messages for epoch message has failed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-EPOCHTDLMSGMARSHAL 3-Error Failed to copy epoch TDL message to IPC buffer epoch number [dec] This operation to build a TDL messages for epoch message has failed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-MSGENQERR 3-Error Unable to enqueue IPC messages to IOS IPC queue. Message: [chars]. An unexpected condition has occurred while IOS trying to enqueue \n\ IPC message to IOS IPC queue in order to send the message to\n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-MSGENQERR 3-Error Unable to enqueue IPC messages to IOS IPC queue. Message: [chars]. An unexpected condition has occurred while IOS trying to enqueue \n\ IPC message to IOS IPC queue in order to send the message to\n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-MSGMARSHALERR 3-Error Unable to copy IPC messages into transport buffer. Message: [chars] An unexpected condition has occurred while IOS trying to copy \n\ IPC message to transport buffer in order to send the message\n\ from IOSd to Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-3-MSGMARSHALERR 3-Error Unable to copy IPC messages into transport buffer. Message: [chars] An unexpected condition has occurred while IOS trying to copy \n\ IPC message to transport buffer in order to send the message\n\ from IOSd to Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGDISPATCH 4-Warning Unable to dispatch received TDL message '[chars]' from Forwarding Manager. LUID: [chars] An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGDISPATCH 4-Warning Unable to dispatch received TDL message '[chars]' from Forwarding Manager. LUID: [chars] An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGDISPATCHNULL 4-Warning TDL messages NULL from IOS. An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGDISPATCHNULL 4-Warning TDL messages NULL from IOS. An unexpected condition has occurred while IOS trying to dispatch\n\ the TDL message handler functions for received TDL messages from \n\ Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGIPCERR 4-Warning Unable to process received IPC messages from Forwarding Manager\n\ error: [chars]. An unexpected condition has occurred while IOS trying to process\n\ received IPC message from Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGIPCERR 4-Warning Unable to process received IPC messages from Forwarding Manager\n\ error: [chars]. An unexpected condition has occurred while IOS trying to process\n\ received IPC message from Forwarding Manager. iosxe-fwdmgr LOG_STD_ACTION IOSXE_FMANRP-4-MSGNONTDLSTATSERR 4-Warning Unable to process received non-TDL stats message from \ Forwarding Manager\n\ error: [chars] [dec]. - - - IOSXE_FMANRP-4-MSGNONTDLSTATSERR 4-Warning Unable to process received non-TDL stats message from \ Forwarding Manager\n\ error: [chars] [dec]. - - - IOSXE_IMCC_CAPI-2-CRASHDUMP 2-Critical Fatal error calling crashdump error: [dec] [chars] A fatal condition has occurred causing IOS to crashdump. iosxe-intfmgr LOG_STD_ACTION IOSXE_IMCC_CAPI-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message name = [chars] from An unexpected condition has occurred while IOS is trying to dispatch\n\ to the TDL message handler functions for received TDL messages from \n\ Interface Manager. iosxe-intfmgr LOG_STD_ACTION IOSXE_IMCC_CAPI-3-MSGDISPATCHNULL 3-Error Received NULL TDL message from IOS An unexpected condition in which IOSD has received a NULL TDL \n\ message from Interface Manager. iosxe-intfmgr LOG_STD_ACTION IOSXE_IMCC_CAPI-3-MSGIPCERR 3-Error Unable to process received IPC messages from Interface Manager\n\ error: [chars] An unexpected condition has occurred while IOS trying to process a\n\ received IPC message from Interface Manager. iosxe-intfmgr LOG_STD_ACTION IOSXE_IMCC_CAPI-6-CMSTATUS 6-Information Interface Manager Process is [chars] The current status of Interface Manager Process. - LOG_STD_NO_ACTION IOSXE_IMSP_ADJ-3-ENCSIZE 3-Error Invalid encap length [dec] which is larger than max allowed [dec] bytes An unexpected condition has occurred which is due to invalid\n\ adjacency encapsulation size being larger than the maximum value\n\ allowed. iosxe-fwdmgr LOG_STD_ACTION IOSXE_IMSP_ADJ-3-ENQUEFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. iosxe-fwdmgr LOG_STD_ACTION IOSXE_IMSP_ADJ-3-NOADJ 3-Error Adjacency entry is null An unexpected condition has occurred which is due to the absence of\n\ an adjacency entry structure. iosxe-fwdmgr "show adjacency" IOSXE_IMSP_ADJ-3-NOFIBHWIDB 3-Error FIB Interface [chars] is null An unexpected condition has occurred which is due to the absence of\n\ a FIB interface structure. iosxe-fwdmgr "show adj" IOSXE_INFRA-2-FATAL_NO_PUNT_KEEPALIVE 2-Critical Keepalive not received for [dec] seconds resetting Punt Inject keepalive message was not received mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-2-FATAL_PUNT_LINK_DOWN 2-Critical Punt Inject link went down resetting Punt Inject link went down mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-APP_SESS_OPEN_FAILED 3-Error An attempt to open [chars] with handle number [dec] has failed [dec] Application session between processes failed to estabish. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-BAD_GLIBC_BUF_FREE 3-Error An IOS buffer is freed into GLIBC buffer pool buffer blockmagic 0x[hec] flags 0x[hec] An IOS buffer is freed into GLIBC buffer pool. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-BIPC_MGS_ALLOC_FAIL 3-Error Allocating [dec] byte for IPC [chars] msg failed: out of memory system is out of memory iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-BSO_MSG_CACHE_ERR 3-Error BSO message query cache update error - [chars] BSO message query cache update error iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-BSO_MSG_HDR_LENGTH_ERR 3-Error BSO message header length [dec] is incorrect BSO message header length is incorrect iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-BSO_MSG_HDR_MSGTYPE_ERR 3-Error BSO message header msgtype [dec] is incorrect BSO message header msgtype is incorrect iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-BSO_MSG_UNMARSHAL_ERR 3-Error BSO message unmarshalling has failed BSO message unmarshalling has failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-CONSOLE_DBUG_DROP 3-Error System dropped [dec] bytes of console debug messages.\n Debugging messages are being generated faster than they can be displayed on the console. The messages can not be guaranteed to be seen so this message replaces the lost messages. - "Consider using conditional debugging or turning off console logging." IOSXE_INFRA-3-CYAN_API_ERROR 3-Error Failed to retrieve platform dependent value of [chars] err=[dec] CYAN API function failed polaris-plat-abs LOG_STD_ACTION IOSXE_INFRA-3-GET_BUFFER_ERR 3-Error Interrupt processing of Punt received packets over socket failed to get a packet buffer for len [dec] Failed to get a packet buffer from the specified pool. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-IDB_CREATE_ERR 3-Error Failed to create IDBInterface Descriptor Block for Punt/Inject Creating an idb corresponding to an interface failed. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-IDB_INIT_ERR 3-Error Failed to initialize IDBInterface Descriptor Block for Punt/Inject Hit error when we initialize idb. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-IFS_DFLT_FS_REG_FAIL 3-Error Unable to set [chars] as a default file system.\n IOSXE's platform dependent code failed to register the default file system. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-IFS_EXTLINK_ADD_FAIL 3-Error Could not add filesystem [chars] to IFS links Attempt to add filesystem root to allow for links failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-IFS_INIT_HIDDEN_FAIL 3-Error IOSXE shim layer initialization failed: Can not create receiving queues IOSXE IOS shim layer initialization of hidden path watch failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-IFS_UDEV_REMOVE_FAIL 3-Error Could not remove udev device [chars] Attempt to remove udev device failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INJECT_EMBEDDED_HDR_LENGTH_ERR 3-Error Can't allot space needed for embedded inject hdr size [dec] exceeds limit Can't allot space needed for embedded inject header exceeds pak header space iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INJECT_FEATURE_ESS_ERR 3-Error ESS segment not found type [dec] hdl 0x%8x Packets to be injected to an unsupported ESS segment iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INJECT_GSB_CTL_INIT_FAIL 3-Error Inject adjacency subblock init failed Adj subblock control or register failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INJECT_HDR_LENGTH_ERR 3-Error Inject hdr size [dec] exceeds limit Inject header length exceeds pak header space iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INJECT_HEADER_ERR 3-Error Transmit packet to the socket failed as packet header length is greater than datagram size. It's an incorrect packet and cannot proceed sending. header length is [dec] datagram size is [dec]. Packet header length is wrong. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-INJECT_NO_IF_OUTPUT_ERR 3-Error Output intf is NULL [chars] Output intf is requred to proceed else skip the feautre iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INVALID_ERRMSG 3-Error Error message type [dec] not defined Error message type used is not defined in IOSXE infrastruction iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-INVALID_RUNTIME_IDX 3-Error Thread runtime index [dec] is not valid Export the thread's running time failed. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-LIIN_TUN_MSG_ERR 3-Error LIIN error - [chars] [chars] [dec] LIIN in Tunnel mode experiencing error iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-MALLOC_FAST_ERR 3-Error Failed to allocate memory for Punt/Inject socket instance malloc_fast failed to allocate memory. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-MCPRP_INIT_PUNTPATH_FD_ERR 3-Error Initializing the ipc control for the puntpath fd failed Initializing the ipc control for the puntpath fd failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-PI_SOCKET_RAW_INIT_ERR 3-Error Punt/Inject socket initialization failed PI Socket Raw initialization failed. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-PI_SOCKET_RAW_PRE_INIT_ERR 3-Error Punt/Inject socket pre-initializationIDB creation failed PI Socket Raw pre-initialization failed. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-PI_TUN_INIT_ERR 3-Error Punt/Inject TUN initialization - [chars] failed PI TUN initialization failed. picasso-infra LOG_STD_ACTION IOSXE_INFRA-3-PUNT_ADDR_RES_ENCAP_ERR 3-Error Punted address resolution packet with unknown encap [chars] Punted packet for ARP/ND with encap not supported iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-PUNT_INCOMP_WRONG_ADJID 3-Error Punted address resolution packet linktype [chars] adj-id [dec] is with linktype [chars]\n CPP needs to punt incomplete adjacency for resolution by specifying the adjacency-id but the included adjacency-id does not match the incomplete adjacency this packet triggered. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_ALLOC_CSB 3-Error Failed to allocate a csb Can't allocate a csb when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_ALLOC_TTY 3-Error Failed to allocate a tty Can't allocate a TTY when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_OPEN_FILE 3-Error Failed to open file: [chars] Failed to open file when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_PARSE_CMD 3-Error Failed to parse command: [chars] Failed to parse a command when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-PUNT_KEEPALIVE_LOG_ERR_WRITE_TO_FILE 3-Error Write to file Id [dec] failed [dec] bytes expected [dec] bytes Write to file failed when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-3-PUNT_SVC_PROC_ERR 3-Error Punt service [chars] create failed Punt service process can not be created iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-PUNT_SVC_TYPE_UNKNOWN 3-Error Punted packet with unknown service type [dec] Punted pak with an unsupported service type iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-RELOAD_INFO_SAVE_FAIL 3-Error Unable to save reload information: [dec]: [chars].\n IOSXE's platform dependent code failed to save the reload information. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_DISPATCH_INIT_FAIL 3-Error IOSXE shim layer initialization dispatch path init failed. IOSXE IOS shim layer initialization of TDL disatch path iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_MEM_FAIL 3-Error IOSXE shim layer initialization failed: Memory initialization failed. IOSXE IOS shim layer initialization of memory failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_PROC_FAIL 3-Error IOSXE shim layer initialization failed: Dispatch process creation failed IOSXE IOS shim layer initialization creating dispatch process failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_TDL_FAIL 3-Error IOSXE shim layer initialization TDL Lib [chars] failed. IOSXE IOS shim layer initialization of TDL library iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_WQ_CHASFS_FAIL 3-Error IOSXE shim layer initialization failed: Can not create receiving chasfs watched queue IOSXE IOS shim layer initialization of watched queue failed iosxe-chassismgr LOG_STD_ACTION IOSXE_INFRA-3-SHIM_INIT_WQ_FAIL 3-Error IOSXE shim layer initialization failed: Can not create receiving queues IOSXE IOS shim layer initialization of watched queue failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_IPC_NOT_PROCESSED 3-Error msg handler returned FALSE for IPC msg for fd [dec] seq_num [dec] service [chars] - - LOG_STD_ACTION IOSXE_INFRA-3-SHIM_NO_IPC_DISPATCH_HDL 3-Error IOSXE shim layer [chars] process message without IPC dispatch handler. IOSXE IOS shim layer has no ipc dispatch handler set iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SHIM_RXMSG_NO_IPC_HDL 3-Error IOSXE shim layer without IPC handler for fd [dec] seqnum [dec]. IOSXE IOS shim layer cannot find ipc handler iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SN_IPFRR_PROC_ERR 3-Error Static Nexthop IPFRR [chars] create failed SN IPFRR process can not be created iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-SOCKET_PEEK_ERR 3-Error Interrupt processing of Punt received packets over socket failed as peek of packet returned error: [chars] Peek at incoming message hit error iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-SOCKET_RECV_ERR 3-Error Interrupt processing of Punt received packets over socket failed as receive packet hit error: [chars] Hit error when receives packet from a socket. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-SOCKET_SEND_ERR 3-Error Transmit packet to the socket hit error: [chars] Transmit a packet to another socket hit error. iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-SWIFT_ORCH_PROC_FAIL 3-Error IOSXE SWIFT Orchestrator process creation failed The SWIFT Orchestrator process could not be created iosxe-iosd-infra LOG_STD_ACTION IOSXE_INFRA-3-TLS_TUN_HOST_IF_ERR 3-Error TLS tunnel to host interface hit error: [chars] TLS tunnel to host interface hit error picasso-infra LOG_STD_ACTION IOSXE_INFRA-3-TLSCD_IF_ERR 3-Error [chars] TLS client daemon interface hit error tlscd-infra LOG_STD_ACTION IOSXE_INFRA-3-TUN_RECV_ERR 3-Error Interrupt processing of Punt received packets over TUN interface failed as read hit error: [chars] Hit error when receives packet from TUN. picasso-infra LOG_STD_ACTION IOSXE_INFRA-3-TUN_SEND_ERR 3-Error Transmit packet to the TUN interface hit error: [chars] Transmit packet to the TUN interface hit error. picasso-infra LOG_STD_ACTION IOSXE_INFRA-3-VM_PAGE_TABLE_ERR 3-Error VM guarded page operation failed address 0x[hec] [chars] VM guarded page avl tree operation error iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-3-VRF_OPEN_CNTRL_FD_ERR 3-Error Control fd open failed for VRF [chars] with error: [chars] Control fd open failed for a specified VRF picasso-infra LOG_STD_ACTION IOSXE_INFRA-4-BSO_MSG_RIB_WATCH_WARN 4-Warning BSO message RIB watch start error BSO message RIB watch start error iosxe-p-punject LOG_STD_ACTION IOSXE_INFRA-4-INJECT_TUN_NONIP_WARN 4-Warning pak with linktype [chars] gets into non-ip tunnel IP/IPv6/MPLS packet should to go through GRE tunnel for non-IP payload iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-4-NO_PUNT_KEEPALIVE 4-Warning Keepalive not received for [dec] seconds Punt Inject keepalive message was not received mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_CLOSE_FILE 4-Warning Failed to close file with descriptor: [dec] Closing of file failed when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_GET_FILE_NAME 4-Warning Failed to get file name: [chars] Punt keepalive log error seen mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_GET_PROCID 4-Warning Failed to get process id Can't get identifier of the process generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_FILE_ID 4-Warning Invalid file descriptor: [dec] Invalid file descriptor was found when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_PARAM 4-Warning Invalid parameter: [chars] Invalid parameter was passed when generating punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-4-PUNT_KEEPALIVE_LOG_ERR_INV_PROCID 4-Warning Invalid proc id [dec] expected [dec] Invalid process trying to generate punt err log mcp-infrastructure LOG_STD_ACTION IOSXE_INFRA-5-PUNT_SVC_CANT_ENQUEUE 5-Notice Punted pak can't be enqueued for service Punted pak enqueue failed iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-5-PUNT_SVC_INVALID_OPT_PKT 5-Notice Invalid IPv4 options packet punted to RP Invalid IPv4 options packet dropped in RP iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-6-AUXTHD_REQUEST 6-Information Too many outstanding requests for file system access Resource temporarily unavailable iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-6-CHASFS_CLOCK_SET_FAIL 6-Information Failed to set Chasfs property on system time change Unable to set chasfs property on system time change iosxe-chassismgr LOG_STD_ACTION IOSXE_INFRA-6-CONSOLE_ACTIVE 6-Information [chars] Indicates that the current instance of IOS is assuming active control of the console. This is informational. - LOG_STD_NO_ACTION IOSXE_INFRA-6-HARDWARE_CLOCK_SET_FAIL 6-Information Failed to set Hardware clock on system time change Unable to set Hardware clock on system time change iosxe-chassismgr LOG_STD_ACTION IOSXE_INFRA-6-PLATFORM_RELOAD 6-Information [chars] Indicates that the current instance of IOS is being reset by the platform code. This is part of a normal reset sequence and the message is informational. - LOG_STD_NO_ACTION IOSXE_INFRA-6-PROCPATH_CLIENT_HOG 6-Information IOS shim client '[chars]' has taken %ld msec runtime: %ld msec to process The specified IOSXE IOS shim client has taken too long to process a received IPC or chasfs message iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-6-SHIM_RXMSG_IPC_INFO 6-Information IOS shim layer process IPC msg for fd [dec] seq_num [dec] ipc_status [dec] - - LOG_STD_ACTION IOSXE_INFRA-6-THEAD_SELECT_ERR 6-Information Inbound message or packet select error [chars]. Socket select operation error in threads iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_INFRA-6-TLSCD_IF_INFO 6-Information [chars] Some info from TLS client daemon interface tlscd-infra LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-BAY_MALLOC_FAILED 2-Critical [chars]: Policy Mgr Bay DB malloc failed for [dec]/[dec] Memory allocation for SPA/EPA failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-CONFIG_NULL 2-Critical [chars]: Configuration is unavailable License Configuration is undefined for this platform. asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_CONFIG_NULL 2-Critical [chars]: Feature Configuration is unavailable Feature Configuration is undefined for this platform. asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_MALLOC_FAILED 2-Critical [chars]: Policy Mgr Feature Registration struct malloc failed Memory allocation for Feature Registration Struct failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-FEATURE_NAME_NULL 2-Critical [chars]: Feature name is NULL License feature name string is NULL asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-IF_MALLOC_FAILED 2-Critical [chars]: Policy Mgr IF DB malloc failed for [dec]/[dec] Memory allocation for SPA/EPA interfaces failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REG_FAILED 2-Critical [chars]: Failed to register [chars] license feature result = [hex] License Registration failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REL_FAILED 2-Critical [chars]: [dec]/[dec]: Lic release failed idx:[dec] feature=[chars] lic_cnt=[dec] License Release failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REL_GEN_FAIL 2-Critical [chars]: [dec]/[dec]: Lic request failed License Release failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REQ_FAILED 2-Critical [chars]: [dec]/[dec]: Lic request failed idx:[dec] feature=[chars] lic_cnt=[dec] License Request failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-2-LIC_REQ_GEN_FAIL 2-Critical [chars]: [dec]/[dec]: Lic request failed License Request failed asr1k-smart-lic LOG_STD_ACTION IOSXE_LICENSE_POLICY_MANAGER-4-DISABLE_MACSEC 4-Warning [chars]: Disabling MACsec configuration due to insufficient license Disabling MACsec configuration from port due to insufficient MACsec license asr1k-port-lic "Purchase/Install MACsec license" IOSXE_LICENSE_POLICY_MANAGER-4-INSUF_LIC 4-Warning [dec]/[dec]/[dec]: Insufficient [chars] license skipping license request assuming customer has honor license Permanent/Evaluation licenses have exhausted skipping license request asuming customer has purchased license DDTS_COMPONENT "Nothing the system is working properly" IOSXE_LICENSE_POLICY_MANAGER-6-LIC_REL_SUC 6-Information [dec]/[dec]/[dec]: License release is successful for [chars] feature License release is successful port allowed to go down DDTS_COMPONENT "Nothing the system is working properly" IOSXE_LICENSE_POLICY_MANAGER-6-LIC_REQ_SUC 6-Information [dec]/[dec]/[dec]: License request is successful for [chars] feature License release is successful port allowed to go down DDTS_COMPONENT "Nothing the system is working properly" IOSXE_LICENSE_RP-3-UNREGISTER_FAIL 3-Error License unregistration not successful for feature [chars] Unregistration failed as license was not released. iosxe-csl "License has to be released before unregistering" IOSXE_LMANRP-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message from lman daemon. An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from lman daemon. iosxe-csl LOG_STD_ACTION IOSXE_LMANRP-3-MSGINITFAIL 3-Error Failed to initalize required lman resource: [chars] During the initialization of the resources required by lman a failure occured. This has prevented lman from being activated. iosxe-csl LOG_STD_ACTION IOSXE_LMANRP-3-MSGOPERATION 3-Error Unable to [chars] the [chars] to license manager i.e. lman daemon. Error: [dec] An unexpected condition has occurred while IOS was trying to send a TDL message to lman daemon. iosxe-csl LOG_STD_ACTION IOSXE_MGMTVRF-3-AFI_ATTACH_FAIL 3-Error Management VRF AFI [chars] attach failed Can not create afi subblock for mgmt vrf iosxe-iosd-infra LOG_STD_ACTION IOSXE_MGMTVRF-3-INTF_ATTACH_FAIL 3-Error Management VRF attach to mgmt [chars] failed Can not associate mgmt port to mgmt vrf iosxe-iosd-infra LOG_STD_ACTION IOSXE_MGMTVRF-3-PROCESS_CREATE_FAIL 3-Error Management VRF process creation failed [chars] Can not create IOS process for mgmt port init iosxe-iosd-infra LOG_STD_ACTION IOSXE_MGMTVRF-3-SET_TABLEID_FAIL 3-Error Installing [chars] Management interface tableid 0x[hec] failed Fail to set mgmt port tableid into Linux kernel iosxe-iosd-infra LOG_STD_ACTION IOSXE_MGMTVRF-3-VRF_CREATE_FAIL 3-Error Management VRF creation failed [chars] Can not create mgmt vrf during system init iosxe-iosd-infra LOG_STD_ACTION IOSXE_MGMTVRF-6-CREATE_SUCCESS_INFO 6-Information Management vrf [chars] created with ID [dec] ipv4 table-id 0x[hec] ipv6 table-id 0x[hec] mgmt vrf and ipv4 ipv6 tables created for mgmt port iosxe-iosd-infra - IOSXE_MLP-2-DB_ALLOC_FAIL 2-Critical MLP link db allocation failed MLP link database error. Memory chunk creation for MLP link database has failed. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command." IOSXE_MLP-2-DB_DELETE_FAIL 2-Critical MLP link db entry delete for link [chars] failed MLP link database error. Removal of entry from MLP link database has failed. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks " "look for mamory corruption causes and " "check for correct database management. " "Execute 'show proc memory' command. " IOSXE_MLP-2-DB_DESTROY_FAIL 2-Critical MLP link database destroy failed MLP link database error. Memory chunk destroy has failed for MLP link database. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute show proc memory command." IOSXE_MLP-2-DB_ENTRY_ALLOC_FAIL 2-Critical MLP link db entry allocation for link [chars] failed MLP link database error. Memory chunk allocation for MLP link database entry has failed. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks and " "look for memory corruption causes. " "Execute 'show proc memory' command." IOSXE_MLP-2-DB_ENTRY_FREE_FAIL 2-Critical MLP link entry free failed MLP link database error. Memory chunk free of MLP link database entry has failed. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks " "and look for memory corruption causes. " "Execute 'show proc memory' command." IOSXE_MLP-2-DB_INSERT_FAIL 2-Critical MLP link db entry add for interface [chars] failed MLP link database error. Insertion of a new entry into MLP link database has failed. iosxe-mlppp "Check for accurate memory management. " "Perform memory leak checks " "look for memory corruption causes " "verify correct database management. " "Execute 'show proc memory' command." IOSXE_MLP-3-ENQUEFAIL 3-Error Unable to send [chars] [chars] message to Forwarding Manager Process An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the Forwarding Manager Processs. iosxe-fwdmgr LOG_STD_ACTION IOSXE_MLP-4-UPDSTATSERR 4-Warning Update MLP statistics error An unexpected condition has occurred when updating mlp statistics iosxe-fwdmgr LOG_STD_ACTION IOSXE_MMA_FMP-3-ENQUEFAIL 3-Error Enqueue of TDL message failed [chars]. - - - IOSXE_MMA-3-ENQUEFAIL 3-Error Enqueue of TDL message failed [chars]. - - - IOSXE_MOCK_SIMULATION-3-BAD_GLIBC_BUF_FREE 3-Error An IOS buffer is freed into GLIBC buffer pool buffer blockmagic 0x[hec] flags 0x[hec] An IOS buffer is freed into GLIBC buffer pool. iosxe-mock-simulation LOG_STD_ACTION IOSXE_MOCK_SIMULATION-3-CALLED_FROM_INT 3-Error API call incorrectly made from interrupt level - DDTS_COMPONENT LOG_STD_ACTION IOSXE_MOCK_SIMULATION-3-NULLQ 3-Error Invalid API parameter An external routine provided by the ASR1000 scheduler was incorrectly called with an invalid NULL pointer. DDTS_COMPONENT LOG_STD_ACTION IOSXE_OIR-3-CARDERR 3-Error Could not read state property for [chars] slot [dec] The OIR facility detected a failure for exceeding the number of retries to find state chasfs property. - LOG_STD_NO_ACTION IOSXE_OIR-3-MODULE 3-Error Missing [chars] for [chars] A hardware or software error occurred. iosxe-iosd-infra LOG_STD_SH_TECH_ACTION IOSXE_OIR-3-OIRTWICE 3-Error Subslot [dec]/[dec] OIR insertion/removal not paired up: [chars] An internal OIR-related error occured for the specified SPA. iosxe-iosd-infra LOG_STD_ACTION IOSXE_OIR-3-POWER_CYCLE_IMMINENT 3-Error The SPA in subslot [dec]/[dec] will be power cycled in [dec] seconds. The SPA in the specified subslot will be power cycled in the amount of time specified in the error message. - LOG_STD_NO_ACTION IOSXE_OIR-3-PROCMSG 3-Error Process msg send failed for process[dec] Process message send failed. iosxe-iosd-infra LOG_STD_ACTION IOSXE_OIR-3-QUIESCE_FAIL 3-Error Quiesce failed for subslot [dec]/[dec] error = [dec] The RP failed to contact the SPA during failover. The SPA will be reset. iosxe-iosd-infra LOG_STD_NO_ACTION IOSXE_OIR-3-SPA_INTF_ID_ALLOC_FAILED 3-Error Failed to allocate interface identifiers for SPA[chars] in slot/bay: [dec]/[dec] Failed to get CC buffer and flow control identifiers for the SPA in the specified subslot Traffic cannot flow through the SPA under this failure condition. This can happen if the system runs out of available identifiers. iosxe-spa-infra "Try to reduce the number of interfaces" "configured in the system either by physically removing the SPAs" "or by changing the system configuration" IOSXE_OIR-3-SPA_MDR_FAIL 3-Error Minimal Disruptive Restart process failed for SPA in subslot [dec]/[dec] reason [chars]. The SPA in the subslot failed Minimal Disruptive Restart. Minimal Disruptive Restart process is aborted and an attempt will be made to recover the SPA by resetting the SPA hardware. iosxe-binos-ha LOG_STD_NO_ACTION IOSXE_OIR-3-UNQUIESCE_FAIL 3-Error Unquiesce failed for subslot [dec]/[dec] error = [dec] The RP failed to unquiesce the SPA in the specified subslot. The SPA will be reset. iosxe-iosd-infra LOG_STD_NO_ACTION IOSXE_OIR-6-CARDRECONCILE 6-Information SPA type changed on subslot [dec]/[dec] from [dec] to [dec] The SPA in the specified subslot has been initialized and it has been detected that it is of a different type to the SPA that was previously in this subslot. - LOG_STD_NO_ACTION IOSXE_OIR-6-CLEAR_FAKE_SPA 6-Information Insert Event received for subslot [dec]/[dec] FAKE_SPA->NONE The OIR facility detected the insertion of a SPA from the subslot number specified in the message. SPA insertion happened while standby Supervisor is booting up. This results into config mismatch which software can't handle and this will cause standby to go for reload. - LOG_STD_NO_ACTION IOSXE_OIR-6-INSCARD 6-Information Card [chars] inserted in [chars]slot [chars] The OIR facility detected the insertion of a card in the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-INSSPA 6-Information SPA inserted in [chars]/[dec] The OIR facility detected the insertion of a SPA in the subslot number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-INSSSFP 6-Information Smart SFP inserted in port [chars] The OIR facility detected the insertion of TSoP/VCoP SSFP in the port number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-OFFLINECARD 6-Information Card [chars] offline in [chars]slot [chars] The OIR facility detected the state change to offline for the card in the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-ONLINECARD 6-Information Card [chars] online in [chars]slot [chars] The OIR facility detected the state change to online for the card in the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-REMCARD 6-Information Card [chars] removed from [chars]slot [chars] The OIR facility detected the removal of a card from the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-REMSPA 6-Information SPA removed from [chars]/[dec] interfaces disabled The OIR facility detected the removal of a SPA from the subslot number specified in the message. The interfaces on that processor will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces. - LOG_STD_NO_ACTION IOSXE_OIR-6-REMSSFP 6-Information Smart SFP removed from port [chars] The OIR facility detected the removal of TSoP/VCoP SSFP in the port number specified in the message. - LOG_STD_NO_ACTION IOSXE_OIR-6-SOFT_RELOADSPA 6-Information SPA[chars] reloaded on [chars] The SPA in the specified subslot is reloaded by the command hw-module subslot slot#/subslot# reload - LOG_STD_NO_ACTION IOSXE_OIR-6-SOFT_STARTSPA 6-Information SPA[chars] restarted in [chars] The SPA in the specified subslot is restarted by the command hw-module subslot slot#/subslot# start - LOG_STD_NO_ACTION IOSXE_OIR-6-SOFT_STOPSPA 6-Information SPA[chars] stopped in [chars] interfaces disabled The SPA in the specified subslot is stopped by the command hw-module subslot slot#/subslot# stop The interfaces on that processor will be administratively shut down and marked as removed. The routing table will be flushed of any routes through the removed interfaces. - LOG_STD_NO_ACTION IOSXE_OIR-6-SPARELOAD 6-Information SPA reloaded on subslot [dec]/[dec] The SPA in the specified subslot is reloaded. - LOG_STD_NO_ACTION IOSXE_OIR-6-SYNCSPA 6-Information SPA [chars] reloading to come up in [chars] mode The SPA in the specified subslot is reloaded by the command hw-module subslot slot#/subslot# reload - LOG_STD_NO_ACTION IOSXE_PEM-3-FAN_FAIL_SHUTDOWN 3-Error More than one [chars] has failed Leads to shutdown the system The Temperature sensor reaching maximum threshold value working properly. - LOG_STD_ACTION IOSXE_PEM-3-FANFAIL 3-Error The fan in [chars]/[dec] is encountering a failure condition The fan's hardware is reporting that the fan is failing. This is most likely because the hardware detects the fan as spinning below the minimum speed. - LOG_STD_ACTION IOSXE_PEM-3-PEMCHASFSERR 3-Error The PEM in [chars] has encountered a system software error. The PEM's underlying software for storing PEM state is not working properly. iosxe-chassismgr LOG_STD_ACTION IOSXE_PEM-3-PEMFAIL 3-Error The Power Supply in [chars] is switched off or encountering a failure condition. The PEM hardware has been either switched off or is reporting a failure condition. iosxe-chassismgr LOG_STD_ACTION IOSXE_PEM-3-PEMREDALARM 3-Error Cannot enable power redundancy mode [chars] because the system is in software alarm state caused by previous active power-supply failures while in redundancy Configuration set by user cannot be accepted as there are previous active power supply failures while in redundancy. Letting redundancy with failed supplies would reduce the total available power - "Insert additional power supplies or restore all the previously failed supplies " "in active slots before the system went in Alarm state" IOSXE_PEM-3-PEMREDLOWSTANDBY 3-Error Cannot activate [chars] configuration. Total power budget of standby power supplies is [dec]W. Standby power must be greater than or equal to the largest power supply capacity [dec]W. Operating in unprotected mode Should insert at least one ps in standby slots with a capacity greater than or equal to the largest capacity power supply in the system. The configuration will be applied automatically once requirements are met. - LOG_STD_ACTION IOSXE_PEM-3-PEMREDNOPWR 3-Error Cannot enable power redundancy mode [chars] because config would create mode with insufficient [chars] power Configuration set by user is not valid as power supplies in the active slots do not contain enough power to meet the power requirements - "Insert additional power supplies and configure them to be active or " "configure current standby power supplies to active such that " "power requirements are met" IOSXE_PEM-3-SSFP_TEMPERATURE_RAISE 3-Error [chars] transceiver temperature reached threshold value Leads to shutdown of the system The Temperature sensor reaching maximum threshold value working properly. - LOG_STD_ACTION IOSXE_PEM-3-TEMPERATURE_RAISE 3-Error Sensor [chars] has reached maximum temperature value Leads to shutdown of the system The Temperature sensor reaching maximum threshold value working properly. - LOG_STD_ACTION IOSXE_PEM-6-FANOK 6-Information The fan in [chars]/[dec] is functioning properly The fan was reporting a failure condition. This message indicates that the fan is no longer reporting a failure - LOG_STD_ACTION IOSXE_PEM-6-INSPEM_FM 6-Information PEM/FM [chars] inserted The platform detected the insertion of a power/fan module in the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_PEM-6-PEMOK 6-Information The PEM in [chars] is functioning properly The PEM hardware may have been either switched off or reporting a failure condition. This message indicates that the PEM is no longer either switched off or reporting a failure - LOG_STD_ACTION IOSXE_PEM-6-REMPEM_FM 6-Information Power Supply/Fantray module [chars] removed The platform detected the removal of a power/fan module in the slot number specified in the message. - LOG_STD_NO_ACTION IOSXE_PLATFORM_RESOURCE_DCA-3-DCA_CFG_ERROR 3-Error Platform Resource Dynamic Core Allocation Configuration Error [chars] Eror occured while configuring dynamic core allocation across system components. iosd-infra "Check System Core Allocations" IOSXE_PLATFORM_RESOURCE_DCA-3-DCA_ENABLE_FAIL 3-Error Platform Resource Dynamic Core Allocation Failure An unexpected error occurred during attempt to dynamically apply a platform resource template configuration. System reboot required. iosd-infra "Reboot the system" IOSXE_PLATFORM_RESOURCE_DCA-5-DCA_ENABLE_NOTICE 5-Notice Platform Resource profile [chars] : [chars] Informational message to indicate the start and completion of dynamically applying platform resource template configuration. iosd-infra LOG_STD_ACTION IOSXE_PLATFORM-3-WDC_INVALID_LENGTH 3-Error WDC length can not be determined: [dec] WDC length was not retrieved properly iosxe-csl "Check if WDC is programmed on this device" IOSXE_PLATFORM-3-WDC_NOT_FOUND 3-Error WDC returned length: [dec] WDC length was set to 0 which specifies probably WDC does not exist iosxe-csl "Check if WDC is programmed on this device" IOSXE_PLATFORM-3-WDC_TLV_NOT_FOUND 3-Error WDC TLV could not be read from the Quack device WDC TLV couldn't be read from the Quack device iosxe-csl "Check if WDC is programmed on this device" IOSXE_PROCMIB -4-MSGERR 4-Warning [chars] Error with process mib message from sub-slot [dec]/[dec] When processing a process MIB message from the specified subslot the specified error has occurred. iosxe-mibs LOG_STD_ACTION IOSXE_PROCMIB -4-SENDMSGERR 4-Warning Failure in sending process mib information from subslot [dec]/[dec] to RP [chars] A failure is encountered when sending process MIB statistics from the IOS driver for the subslot specified in the message to RP IOS. This indicates a software failure. iosxe-mibs LOG_STD_ACTION IOSXE_QFP-2-LOAD_EXCEED 2-Critical Slot: [dec] QFP:[dec] Load [dec]%% exceeds the setting threshold [dec]%%.\n 5 secs traffic rate on QFP: Total Input: %llu pps %llu.%llu kpps %llu bps %llu.%llu mbps QFP Load exceeds setting threshold. - "Monitor the traffic load." IOSXE_QFP-2-LOAD_RECOVER 2-Critical Slot: [dec] QFP:[dec] Load [dec]%% recovered.\n 5 secs traffic rate on QFP: Total Input: %llu pps %llu.%llu kpps %llu bps %llu.%llu mbps QFP Load recovered. - "No action required normal operation." IOSXE_RP_ALARM-2-ESP 2-Critical [chars] [chars] [chars]: [chars] [chars] - - - IOSXE_RP_ALARM-2-ESP 2-Critical [chars] [chars] [chars] [chars] [chars] No ESP running alarm information - LOG_STD_NO_ACTION IOSXE_RP_ALARM-2-PEM 2-Critical [chars] [chars] [chars]: [chars] [chars] - - - IOSXE_RP_ALARM-2-PEM 2-Critical [chars] [chars] [chars] [chars] [chars] Power Entity Module missing information - LOG_STD_NO_ACTION IOSXE_RP_ALARM-6-INFO 6-Information [chars] [chars] [chars]: [chars] [chars] - - - IOSXE_RP_ALARM-6-INFO 6-Information [chars] [chars] [chars] [chars] [chars] Alarm assertion or deassertion information. - LOG_STD_NO_ACTION IOSXE_RP_CFG_INFO-6-MCPRP_ASCII_CFG_APPLIED 6-Information System configuration : ASCII System is using ASCII config during startup polaris-mgbl-infra LOG_NO_ACTION IOSXE_RP_CFG_INFO-6-MCPRP_BINARY_CFG_APPLIED 6-Information System configuration : Binary System is using binary config during startup polaris-mgbl-infra LOG_NO_ACTION IOSXE_RP_CFG_NOT-2-MSGIPCINITERROR 2-Critical Error initializing IPC queue An unexpected condition in which IOS could not initialize\n\ a message queue to the PSD. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-2-MSGNOEXP 2-Critical Can not construct a '[chars]' message for configuration export: [chars] This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-2-MSGTDLERROR 2-Critical Error processing TDL message. [dec] An unexpected condition in which IOS has received a TDL \n\ message which it can not process. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-2-MSGTDLINITERROR 2-Critical Configuration Notification messaging module initialization failed: Unable to initialize messaging: [chars] The Configuration Notification subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Notification of configuration to critical modules cannot proceed. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_NOT_COMPATIBLE 3-Error Primary image is not compatible the system is going to reload as per user request. Primary image which is set in boot statement is not compatible with system. Primary image incompatible it should prompt the user to see if they wish to proceed. Aborting reload. esg-chassismgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_NOT_FOUND 3-Error Primary image is not found the system is going to reload as per user request. Primary image which is set in boot statement either does not exist or not found. Primary image is not found it should prompt the user to see if they wish to proceed. Aborting reload. asr1k-chassismgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-BOOT_IMAGE_VALIDATE_UNSUPPORTED_PLATFORM 3-Error Boot image validate function does not recognize the current platform type. This is likely due to new chassis/platform variant being introduced. The reload operation is not affected however presence of this syslog indicates that esg-chassismgr component owner should investigate and determine root cause. Boot image validate function does not recognize the current platform type. This is likely due to new chassis/platform variant being introduced. The reload operation is not affected however presence of this syslog indicates that esg-chassismgr component owner should investigate and determine root cause. esg-chassismgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-BOOT_VAR_NOT_SET 3-Error Either the boot variable does not exist or the buffer is too small. Keep it blank. Boot variable either does not exist or buffer is too small. Not able to set boot variable. Ignoring it.Aborting reload. asr1k-chassismgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCP_DBPERSIST_ERROR 3-Error System configuration update could not complete When a 'reload' operation occurs this chasfs property is read to determine the status of the DB persist/restore/delete operation. This message indicates that the operation failed. polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCP_DBPERSIST_STAT 3-Error Failed to read [chars] property: [dec] When a 'reload' operation occurs this chasfs property is read to determine the status of the DB persist/restore/delete operation. This message indicates that the read failed. polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCP_FRU_INVALID 3-Error Unknow FRU location: [chars] Unknown FRU location polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCP_FRU_LOCATION 3-Error Failed to get local FRU location: [dec] Unable to get local FRU location polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_DEL_FAILED 3-Error System could not delete binary startup-config error: [chars] Each time that you erase startup-config binary-config is also erased. This message indicates that system failed to erase binary-configuration. polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_GEN_FAILED 3-Error System could not generate binary startup-config error: [chars] Each time that you save running-config to startup-config a binary file is created and the ASCII file is updated. A valid binary configuration file reduces the overall boot time significantly. This message indicates that system failed to generate binary-configuration. polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MCPRP_BINARY_CFG_REPLAY_FAILED 3-Error System could not apply binary startup-config error: [chars] During reload system uses binary startup configuration. A valid binary configuration file reduces the overall boot time significantly. This message indicates that system failed to apply binary-configuration. polaris-mgbl-infra LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGENCRYPTINVALID 3-Error The mcprp_cfg_notify subsystem has seen an encryption type it does\n\ not recognize. [dec] An unexpected condition has occurred while IOS is trying to process\n\ a username command. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGIPCTXERROR 3-Error IPC transmit error. [dec] An unexpected condition in which IOS encountered an error\n\ trying to send a message to another process. [dec] iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGNOCAND 3-Error Can not construct a candidate entry for configuration export This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGNOPWARR 3-Error Can not construct an array for configuration export This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGNOREPLMSG 3-Error Can not construct a replace message for configuration export This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGNOUPDATEMSG 3-Error Can not construct an update message for configuration export This error usually indicates either an out of memory condition or a TDL error. If ample memory is available then the the TDL error may indicate a version conflict with respect to configuration. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-MSGOBJNULL 3-Error An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null. An unexpected condition has occurred while IOS is trying to process\n\ a username command. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_CFG_NOT-3-NVWRITE_EXPORT 3-Error Failed to export [chars] notification: [dec] When a 'write memory' or 'write erase' operation occurs the Configuration Notification subsystem exports this event into the chassis file system. This message indicates that the export failed. access LOG_STD_ACTION IOSXE_RP_CFG_NOT-6-IOX_SERVICE_NOTSUPPORTED 6-Information IOx service not supported. IOx service is not supported in this platform currently. This may be either due to the feature unavailability or due the current inadequate license level of the system. iox-caf - IOSXE_RP_CFG_NOT-6-MCPRP_BINARY_CFG_MISSING 6-Information Binary configuration missing. System is booted with ASCII based startup configuration. Please perform \write mem\ to generate binary configuration. System uses binary-config internally to reduce overall bootime significantly. polaris-mgbl-infra - IOSXE_RP_DIAG_TEST-3-MSGDIAGCANTENQUEUE 3-Error Online diagnostics could not enqueue a diagnostic test response. The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-3-MSGDIAGTIMEOUT 3-Error A timeout occured while waiting for an online diagnostic \n\ test to finish. The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-3-MSGIPCTXERROR 3-Error IPC transmit error. [dec] An unexpected condition in which IOS encountered an error \n\ trying to send a message to another process. [dec] iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-3-MSGOBJNULL 3-Error An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null. An unexpected condition has occurred while IOS is trying to perform \n\ online diagnostics work. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-3-MSGRESPTDLERR 3-Error A diagnostic test result could not be read properly. The iosxe online diagnostics failed to respond properly to a \n\ request by the system to perform a diagnostic test. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-3-MSGTDLERROR 3-Error Error processing TDL message. [dec] An unexpected condition in which IOS has received a TDL \n\ message which it can not process. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-4-ERR_CNTR_HM_TEST_DATA 4-Warning ERROR_COUNTER_DATA: ID:[dec] IN:%D PO:[dec] RE:[dec] RM:[dec] DV:[dec] EG:[dec] CF:[dec] TF:[dec] Error Counter Monitoring test has failed on one of the cards of IOSXE Corresponding Data is printed. iosxe-sch-gold LOG_STD_ACTION IOSXE_RP_DIAG_TEST-4-ERR_CNTR_HM_TEST_FAIL 4-Warning ERROR_COUNTER_WARNING: Slot [chars] Error counter exceeds threshold system operation continue. Error Counter Monitoring test has failed on the given card of IOSXE. iosxe-sch-gold LOG_STD_ACTION IOSXE_RP_DIAG_TEST-6-MSGOUTOFORDER 6-Information Received a test result after IOS had timed out. [[dec][dec]] When a diagnostic test is performed IOS waits for the result \n\ be returned. If it does not return in a specified period of \n\ IOS times out on that test request and moves on. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DIAG_TEST-6-MSGUNEXPECTEDEVENT 6-Information Unexpected event recieved. When a diagnostic test is performed IOS waits for the result\n\ be returned. While waiting for the result IOS unexpectedly\n\ received an event it does not recognize and so IOS stopped\n\ waiting for the result. The test continued IOS does not know\n\ what the results are and hence can not report them. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-BULK_SYNC 3-Error Failed to send [chars] information to peer - iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-CF 3-Error Datapath IDB CF operation failed - [chars] Failure in some datapath ID CF activity. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-DECODE 3-Error Decode via [chars] of [chars] failed The active route processor has sent a notification to the standby\n\ to inform of the completion of the bulk synchronization of the DPIDX\n\ configuration. The standby has failed to respond to the active\n\ informing that it received the notification noting the reason for\n\ the failure. The resultant action taken by the standby route\n\ processor is an attempt to resynchronize. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-DOWNLOADFAIL 3-Error Unable to download [chars] message to [chars] An unexpected condition has occurred which resulted in a configuration \n\ not being sent to the reported process. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-DYN_SYNC 3-Error Failed to process [chars] dynamic state The incremental synchronization of the DPIDX configuration to the\n\ standby RP has failed to complete successfully. This implies that the\n\ configuration state between the active and standby RP is\n\ inconsistent. iosxe-infmgr "show interfaces" IOSXE_RP_DPIDB-3-EFPSTATSFAILED 3-Error EFP stats message data get error: [dec] for EFP [dec] on [chars] An unexpected error occurred extracting fields from an EFP stats\n\ message. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-FASTNOTIFY 3-Error Fast notify failed for [chars] A fast notify message failed iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-FRRLDFLOWIDDELETIONFAILED 3-Error Deletion of fast-reroute flow ID with manager failed An unexpected condition has occurred that deletion of\n\ fast-reroute flow ID. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDBBADTYPE 3-Error Datapath IDB type [dec] is not valid An unexpected condition has occurred as the type of\n\ a datapath IDB is not valid. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDBEXIST 3-Error Datapath IDB already exists in this mapping entry: [chars]-[dec] An unexpected condition has occurred that an attempt is made\n\ to save datapath IDB in a mapping entry filled by another. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDBNONEXIST 3-Error Datapath IDB does not exist in this mapping entry: [chars]-[dec] Datapath IDB lookup points to empty mapping entry. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDBNOTVAI 3-Error Invalid API call for [chars] Failure in an internal API iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDXALLOCFAILED 3-Error Datapath IDB index allocation failed: [chars] An unexpected condition has occurred as all the available of\n\ datapath IDB indices are used. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDXBADRANGE 3-Error Datapath IDB index [dec] is not in a valid range An unexpected condition has occurred as the index of\n\ a datapath IDB is not valid. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDXDELETIONFAILED 3-Error Deletion of datapath IDB index from the database failed \n\ [chars] - 0x[hec] rc [dec] An unexpected condition has occurred that deletion of\n\ datapath IDB indices failed. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDXINSERTFAILED 3-Error Insertion of datapath IDB index [dec] into database failed An unexpected condition has occurred that insertion of\n\ datapath IDB indices failed. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IDXLOOKUPFAILED 3-Error Lookup of datapath IDB index from the database failed [chars] An unexpected condition has occurred that lookup of\n\ datapath IDB indices failed. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-IP_MTU_ALLOC_FAIL 3-Error No hardware resources for [dec] byte IP MTU on [chars] We reached to the threshold of maximum supported unique IP MTU \ on this platform. - LOG_STD_NO_ACTION IOSXE_RP_DPIDB-3-LIST 3-Error List [chars] failed for [chars] List enqueue or removal failed iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-MTU_ALLOC_FAIL 3-Error No hardware resources for [dec] byte MTU on [chars] We reached to the threshold of maximum supported unique MTU on \ this platform. - LOG_STD_NO_ACTION IOSXE_RP_DPIDB-3-NOHWSUBBLOCK 3-Error HWIDB [chars] does not have a hardware subblock An unexpected condition has occurred that no hardware subblock\n\ was previously allocated for a HWIDB. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-NOSWSUBBLOCK 3-Error SWIDB [chars] does not have a software subblock An unexpected condition has occurred that no software subblock\n\ was previously allocated for a SWIDB. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-NULLTIMER 3-Error NULL timer A timer is NULL iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-RECEIVE 3-Error Message via [chars] is [chars] The ISSU negotiation with the peer failed to start for either the CF or\n\ IPC transport with the reason specified. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-RF 3-Error Datapath IDB RF operation failed - [chars] Failure in some datapath ID RF activity. iosxe-infmgr "show interface" IOSXE_RP_DPIDB-3-RPC 3-Error Datapath IDB RPC operation failed - [chars] An operation pertaining to the ISSU support for DPIDX failed to complete\n\ using either the CF or IPC transport context with the reason\n\ specified iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-3-TRANSFORM 3-Error [chars] of [chars] via [chars] failed for dpidx [dec] An attempt to either encode or decode a versioned synchronization\n\ message has failed due to an internal error encountered by the ISSU\n\ component. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-5-MTU_ADVISORY 5-Notice [chars] - [chars] MTU Advisory - LOG_STD_NO_ACTION IOSXE_RP_DPIDB-6-READY 6-Information [chars] peer not ready discarding [chars] The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode. - - IOSXE_RP_DPIDB-6-RELOAD 6-Information [chars] reloading [chars] A synchronization attempt between the active and standby RP peers has\n\ failed with the reason indicated. The standby peer is reloaded in an\n\ attempt to resynchronize when operating in a stateful redundant\n\ mode. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_DPIDB-6-TIMEOUT 6-Information Bulk sync is flow controlled by [chars] The bulk synchronization of the DPIDX configuration to the standby RP\n\ has encountered a flow control condition which has effected a timeout\n\ awaiting the condition to clear. This will result in a reload of the\n\ standby RP to allow the bulk synchronization to restart. iosxe-infmgr LOG_STD_ACTION IOSXE_RP_EWLC_NOT-2-EWLC_STARTUP 2-Critical Starting EWLC process [dec] Sending TLD message to start up all eWLC processes iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_EWLC_NOT-2-MSGIPCINITERROR 2-Critical Error initializing IPC queue An unexpected condition in which IOS could not initialize\n\ a message queue to the PSD. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_EWLC_NOT-2-MSGTDLERROR 2-Critical Error processing TDL message. [dec] An unexpected condition in which IOS has received a TDL \n\ message which it can not process. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_EWLC_NOT-2-MSGTDLINITERROR 2-Critical eWLC startup module initialization failed: Unable to initialize messaging: [chars] The eWLC startup subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Notification of configuration to critical modules cannot proceed. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-BUFF_OFFSET_NULL 3-Error Unable to utilize the memory buffer provided by the Checkpoint Facility. This [chars] CF client has failed to Bulk Sync. This error indicates the Checkpoint Facility is having problems recognizing its own buffer layout. If this occurs during Bulk Sync then Bulk Sync will terminate without completing. Otherwise the incremental Sync will fail. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-CF_CANNOT_REGISTER 3-Error The call to add this [chars] CF client to the Checkpoint Facility failed with the error [chars]. This client is unable to proceed and will not be registered. For some reason the Checkpoint Facility will not register this client. As a result the Standby will never receive synchronized state from this CF client on the Active RP The system is not capable of SSO and HA switchover. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-CF_SEND_BULK_NONBLOCKED 3-Error The Checkpoint Facility reported the error [chars] while attempting to send a message. Bulk Sync of this [chars] CF client is terminating. This error indicates the Checkpoint Facility has internal problems related to IPC and cannot perform a non-blocked send operation. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-CF_SEND_INCR_NONBLOCKED 3-Error The Checkpoint Facility reported the error [chars] while attempting to send a non-blocked message. The Incremental Sync transaction for this [chars] CF client cannot be sent to the Standby RP. This error indicates the Checkpoint Facility has internal problems related to IPC. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-DECODE 3-Error Decode via CF of [chars] failed A message sent via the CF transport failed in its attempt\n\ to be decoded on the standby. The resultant action taken by the\n\ standby route processor is an attempt to resynchronize. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-DEFERRED_DURING_BULK_SYNC 3-Error Encountered error [chars] while trying to place an [chars] transaction on the Deferred list during Bulk Sync for the [chars] CF client. Unable to cache a deferred transaction while Bulk Sync is underway. This can adversely impact SSO state on the Standby RP. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-NO_BUFF_FOR_SYNC 3-Error The Checkpoint Faclity reported the error [chars] during a request for a buffer length of [dec]. This [chars] CF client has failed to synchronize a transaction to the Standby RP. This error indicates that the buffer management within the Checkpoint Facility has either run out of buffers or has some other problem. If this occurs during Bulk Sync then Bulk Sync will terminate without completing. Otherwise the incremental Sync will fail. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RECEIVE 3-Error Client reports message CF is [chars] An attempt to receive and process a versioned negotiation or\n\ synchronization message has failed due to an internal error\n\ being detected by the information received from the CF component. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_ADD_CLIENT_FAILED 3-Error The RF facility failed to add this [chars] client reason given is [chars]. An operation pertaining to the ISSU support for SPA MARMOT IDs failed \n\ to complete using the CF transport context with the reason specified iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_IF_ID_REGEN_ERROR 3-Error Error code [dec] encountered trying to regenerate interface flow-control identifer. If id [dec] resides in slot/subslot/port [dec]/[dec]/[dec]. - - - IOSXE_RP_IF_FLOW_IDS-3-RF_PEER_EVENT_BUFFER 3-Error This [chars] RF client is unable to acquire an event buffer to send an RF peer message the error [chars] was returned. This indicates the RF facility is unable to provide a message buffer needed to communicate with the RF peer. As a consequence the RF progression may be compromised. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_POOL_REGEN_ERROR 3-Error Id Pool Regeneration encountered error code [dec] cannot switchover. The background process which performs Flow Control Id Pool regeneration encountered an error. As a consequence the Standby does not have valid Flow Id pools and cannot progress to Active state. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_POOL_REGEN_PROCESS_FAILED 3-Error The [chars] RF client Failed to create the Id Pool Regeneration process. The background process which performs Flow Control Id Pool regeneration failed to start. As a consequence the Standby will never obtain the relevent SSO state to enable HA switchover. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_PROCESS_FAILED 3-Error This [chars] RF client Failed to create the Bulk Sync Process. The background process which performs the RF Bulk Sync failed to be created. As a consequence the Standby will never obtain the relevent SSO state to enable HA switchover. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_SEND_PEER 3-Error This [chars] RF client encountered error [chars] when attempting to send a peer message. This indicates the RF facility could not send a message to the RF peer. As a consequence the RF progression may be compromised. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-RF_SPA_ID_REGEN_ERROR 3-Error Error code [dec] encountered trying to regenerate spa [chars] identifier in slot/subslot [dec]/[dec] - - - IOSXE_RP_IF_FLOW_IDS-3-SEND_FAIL_RELOAD 3-Error Checkpoint Facility Failed to send a [chars] transaction for this [chars] CF client. Reloading the Standby RP. This indicates the underlying Checkpoint Facility could not deliver a message sent from the active RP to the standby RP. The process will automatically reload the standby RP. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-3-TRANSFORM 3-Error [chars] of [chars] via CF failed The ISSU negotiation with the peer failed to start for either the CF or\n\ IPC transport with the reason specified. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-4-DEF_LIST_REMOVE 4-Warning Failed to remove one entry from the Deferred Sync list for the [chars] CF client. An unexpected condition occured during list maintenance. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-6-CFPEER_CANNOT_RECV 6-Information The Checkpoint Peer is not ready to receive messages. The Incremental Sync transaction for this [chars] CF client will not occur. This error indicates the Checkpoint Facility has signalled the peer has gone away. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_IF_FLOW_IDS-6-READY 6-Information [chars] peer not ready discarding [chars] The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode. - - IOSXE_RP_MGMTE_INV-3-PROCESS_CREATE_FAIL 3-Error Management ethernet inventory process creation failed Can not create IOS process for RP management ethernet inventory updation bb-intrepid-drv LOG_STD_ACTION IOSXE_RP_MGMTE-3-MSGCREATENULL 3-Error Cannot allocate [chars] TDL message An unexpected condition in which IOS cannot allocate TDL message for Management ethernet. iosxe-tdl LOG_STD_ACTION IOSXE_RP_MGMTE-3-MSGTDLINITERROR 3-Error Management ethernet interface messaging module initialization failed: Unable to initialize messaging: [chars] The Management ethernet interface subsystem has failed to initialize the infrastructure for messaging with the Pluggable Services Daemon. Configuration of management ethernet modules cannot proceed. iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_RP_MGMTE-3-PROCESS_CREATE_FAIL 3-Error Management ethernet statistics process creation failed Can not create IOS process for RP management ethernet port statistics collection iosxe-iosd-fastpath LOG_STD_ACTION IOSXE_RP_NV-3-BACKUP_NV_ACCESS_FAIL 3-Error Initial read of backup NVRAM contents failed This error happens when the contents of the backup NVRAM cannot be read during system initialization. The failure may be due to data corruption of the backup NVRAM contents. The primary nvram contents will be backed up here again. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_NV-3-NV_ACCESS_FAIL 3-Error Initial read of NVRAM contents failed This error happens when the contents of the NVRAM cannot be read during system initialization. The failure may be due to data corruption of the NVRAM contents. The initial configuration dialog will be entered and the configuration must be restored. iosxe-binos-ha LOG_STD_ACTION IOSXE_RP_ONLINE_DIAG-3-MSGMAXCARDS 3-Error Online diagnostics maximum number of cards exceeded An unexpected condition in which IOS has attempted to \n\ register more hardware cards for diagnostics than it\n\ expects the maximum to be. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_ONLINE_DIAG-3-MSGOBJNULL 3-Error An unexpected condition in which IOS has received a null\n\ pointer that it expects to be non-null. An unexpected condition has occurred while IOS is trying to perform\n\ online diagnostics work. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_ONLINE_DIAG-3-MSGTDLERROR 3-Error Error processing TDL message. [dec] An unexpected condition in which IOS has received a TDL\n\ message which it can not process. iosxe-chassismgr LOG_STD_ACTION IOSXE_RP_SPA-0-INVALID_ETHERNET_MSG_HANDLER_FVT 0-Emergency Invalid Ethernet Message handler Function Vector Table for [chars] Module [dec]/[dec] TDL Message handler vector table is not registered for Ethernet Module DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-BAD_IFCOMTYPE 3-Error Bad ifcom message type=[dec] A SPA module passed down a message that the RP software\n\ was not prepared to handle. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-CI_UPDATE_FAIL 3-Error Failed to update connection identifier for interface [chars] The SPA driver is not able to update the datapath connection identifier for the interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-DPIDX_LKUP_FAIL 3-Error Failed to retrieve datapath identifier for interface [chars] The SPA driver is not able to retrieve the datapath identifier for the interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-ERROR 3-Error common_str_empty_str This message can take many forms. It provides information about a\n\ software error. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-ERROR_INFO 3-Error common_str_empty_str This message can take many forms. It provides information about a\n\ software error without traceback. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-FLOWID_ALLOC_FAIL 3-Error Failed to allocate a flow control identifier for interface [chars] The SPA driver is not able to allocate the datapath flow control identifier for the interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-FLOWID_RELEASE_FAIL 3-Error Failed to release a flow control identifier for interface [chars] status = [dec] The SPA driver is not able to release the datapath flow control identifier for the interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-FOREVER 3-Error cmd [dec] to [chars] slot [dec]/[dec] took [dec] usecs done [hec] A CCB command from the RP to a SPA module took longer than expected. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-FRR_CFG_REC_FAIL 3-Error Failed to record fast reroute conifguration on [chars]: [chars] This message is displayed when a fast reroute configuration is not properly recorded. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-HWIDB_FAILURE 3-Error Creation: slot [dec] subSlot [dec] port [dec] vc [dec] Failed to create an interface hwidb. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-HWIDB_INIT_FAIL 3-Error Failed to initialize data structure for SPA port [dec]/[dec]/[dec] A SPA driver was not able to properly initialize a data structure mentioned in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-IFCFG_CMD_NOT_OWNER 3-Error Process '[chars]' waiting for interface configuration command 0x[hec] to A process on the RP sent an configuration command to the slot specified in the error message and a different process waited for the result. This could cause incorrect line card configuration states. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-IFCFG_FOREVER 3-Error to [chars] slot [dec]/[dec] took [dec] usecs ret_val %lu A interface config command from the RP to a SPA module took\n\ longer than expected. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-IFCFG_NO_UNIQUE_KEY 3-Error No unique-key generator registered for interface configuration command [dec]. The High Availability component for SPA modules is unable to properly synchronize state information for the current configuration. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-INVALID_ETHERNET_MSG_HANDLER 3-Error Invalid Message Handler for [chars] on [dec]/[dec] [chars] Module TDL Message handler is not registered for Ethernet Module DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-INVALID_PORT_NUM 3-Error slot=[dec] port=[dec] hwidbType=0x[hec] max_port_num=[dec] LCtype=0x[hec] The port number is out of range. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-IOMD_CONFIG_FAIL 3-Error The IOMD return value for BAY: [dec] CMD [dec]: code:%0x msg:[chars] Failed to configure in IOMD. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The RP failed to allocate a buffer for communication with a SPA DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-IPCPORT 3-Error Failed to [chars] IPC port '[chars]' error [chars] The standby has failed to notify the active that its bulks\n\ synchronization of the SPA TSM has completed. The resultant action\n\ taken by the standby route processor is an attempt to resynchronize. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-IPCPORTFAIL 3-Error Failed to open IPC port '[chars]' with error [chars] The RP failed to open a port for communication with a SPA\n\ module. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The RP failed to send a message to a SPA module. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-LIC_REG_FAILED 3-Error [dec]/[dec]/[dec]: Failed to register license feature [chars] err=[hex] License registration has been denied by license manager DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-LIC_REL_FAILED 3-Error [dec]/[dec]/[dec]: Failed to release license feature [chars] handle=0x[hec] err=[hex] License release has been denied by license manager DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-LIC_REQ_FAILED 3-Error [dec]/[dec]/[dec]: Interface enable not allowed - license request failed err=[hex] A 10 Gig License is required to enable this port. License request has been denied by license manager DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-3-MAC_FILTER_ADD_FAIL 3-Error All the available [dec] mac filters for [chars] have been consumed. Failed to add [enet] for interface [chars] The hardware cannot support any more filters. DDTS_COMPONENT "The interface configuration should be reworked " "to not cross the limit set by the hardware." "If the error is still seen please " LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-MAX_SPA 3-Error Power to IPSEC-SPA-2G in [chars] is denied because it has exceeded the number allowed[dec] The number of IPSEC-SPA-2G in a chassis is limited. This message is displayed when the number of IPSEC-SPA-2G in the chassis has exceeded this limit. DDTS_COMPONENT "Use only the number of supported IPSEC-SPA-2G" IOSXE_RP_SPA-3-MISSING_SPA_PKG_ERR 3-Error sipspa[chars] package is not installed for slot = [dec] and subslot = [dec] SPA bootup failed. This message is displayed when attempting to bootup a SPA without installing a subpackage required for the same. - "Download the sub-package required for the " "affected SPA from the Cisco CCO software download site and install " "the same. This SPA can be booted in sub-package mode only. Please " "refer to the Cisco ASR platform documentation for " "obtaining and installing sub-packages." IOSXE_RP_SPA-3-MISSING_SPA_PKG_WARN 3-Error sipspa[chars] package is not installed in standby for slot = [dec] and subslot = [dec]. This message is displayed in standby console when attempting to bootup or restart or reload a WMA SPA without installing a subpackage in the standby RP although the SPA is or will be operational due to prior wma spa package installation in active RP. If switchover takes place the WMA SPA will still be operational. But any subsequent soft or hard oir of the SPA will fail due to missing sub package required to boot up the SPA. Hence it is recommended to complete the wma spa package installation in standby also before switchover or immidiately after switchover. - "Download the sub-package required for the " "affected SPA from the Cisco CCO software download site and install " "the same for the standby RP as is done on active RP. Please refer " "to the Cisco ASR platform documentation for obtaining and installing " "sub-packages." IOSXE_RP_SPA-3-NO_HOST_INFO 3-Error slot [dec] subSlot [dec] spaType 0x[hec] Failed to get information about the host linecard. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-NULL_DATA_STRUCTURE 3-Error common_str_empty_str A SPA driver is not able to retrieve the data structure mentioned in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-SEND_L2_HDR_MSG_FAIL 3-Error slot [dec] subslot [dec] Failed to send ngio L2 header to iomd. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-SEND_NGIO_MSG_FAIL 3-Error NGIO Module message send failed for slot [dec] subslot [dec] Failed to send ngio msg to iomd. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-SONET_ALARM_PROC_ERR 3-Error [chars] Error has occurred while processing in the sonet alarm-proc Either free/create of the memory failed in SONET alarm proc - - IOSXE_RP_SPA-3-SPA_NO_HOST_INFO 3-Error slot [dec] subSlot [dec] PID [chars] Failed to get information about the host linecard. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-3-SPA_WRONGTYPE 3-Error Mismatched SPA type [dec] in slot [dec]/[dec]. Expected type [dec]. The SPA inserted does not match the currently provisioned SPA type. - "Replace wrong SPA with currently provisioned SPA type or type 'no card' " "to allow new card type to be discovered." IOSXE_RP_SPA-3-UNSUPPORTED_SRVCS_SPA 3-Error Service SPA %#X in [dec]/[dec] is not supported. SPA bootup failed. This message is displayed when attempting to bootup any service SPA in router running non K9 image i.e. non-crypto image. - "Download the K9 IOS XE sub-packages and the " "required sub-package for the given service SPA from the Cisco CCO " "software download site and install the same. This SPA can be booted " "in sub-package mode only. Please refer to the Cisco ASR platform " "documentation for obtaining and installing sub-packages." IOSXE_RP_SPA-3-VC_FLOWID_ALLOC_FAIL 3-Error Failed to allocate a flow control identifier for VC [dec] under interface [chars] The SPA driver is not able to allocate the datapath flow control identifier for the VC/interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-VC_INGID_ALLOC_FAIL 3-Error Failed to allocate a ingress identifier for VC [dec] interface [chars] The SPA driver is not able to allocate the datapath ingress identifier for the VC/interface specified in the message. This indicates a software error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-3-VC_PROV_FAIL 3-Error Failed to provision interface [chars] The SPA driver is not able to provision the interface specified in the message. Verify that the SPA hardware is not provisioned above the supported limit. Otherwise this indicates a hardware error. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-4-CCB_PLAYBACK_ERROR 4-Warning CCB playback failed for slot [dec]. The High Availability component for SPA modules failed to synchronize some new state information for the specified slot. DDTS_COMPONENT "Reload the standby supervisor module to force a fresh bulk " "synchronization. If this error recurs " LOG_STD_ACTION IOSXE_RP_SPA-4-CCB_RECORD_ERROR 4-Warning CCB record failed for slot [dec]. The High Availability component for SPA modules failed to record some new state information for the specified slot. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-IFCFG_CMD_TIMEOUT 4-Warning Interface configuration command 0x[hec] to slot [dec]/[dec] timed out The RP sent an configuration command to the slot specified in the error message and received no confirmation for the command. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-IFCFG_DFLT_LIST_ERROR 4-Warning For Interface Configuration command [dec] default retval list search resulted 0x[hec] for slot [dec]/[dec] The High Availability component for SPA modules failed to synchronize some new state information for the specified slot. DDTS_COMPONENT show platform redundancy \ if-config default-retvals IOSXE_RP_SPA-4-IFCFG_PLAYBACK_ERROR 4-Warning Interface Configuration command [dec] playback failed for slot [dec]/[dec]. The High Availability component for SPA modules failed to synchronize some new state information for the specified slot. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-IFCFG_RECORD_ERROR 4-Warning Interface Configuration command [dec] record failed for slot [dec]/[dec]. The High Availability component for SPA modules failed to record some new state information for the specified slot. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-INCR_CFG_SYNC_FAIL 4-Warning [chars] incremental running-config sync for [[dec]/[dec]] failed - [chars][dec] The specified IOSXE incremental running-config sync failed DDTS_COMPONENT "Power cycle the redundant supervisor" IOSXE_RP_SPA-4-IPCFAILED 4-Warning IPC failed to send RPC message to SPA module The RP failed to send an RPC message via IPC to a SPA module. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-4-LCLOG_PARSE_ERR 4-Warning Error parsing logger message: [chars] from subslot [dec]/[dec] The SPA module passed down a logger message that could not be parsed. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-LCLOG_TOOLONG 4-Warning Message too long from slot [dec]/[dec]: [dec] bytes The SPA module passed down a logger message that is too long for\n\ the RP to handle. DDTS_COMPONENT LOG_STD_ACTION IOSXE_RP_SPA-4-SEMAHOG 4-Warning Process [dec] [chars] hogging [chars]! calling proc [dec] [chars] - - - IOSXE_RP_SPA-4-SPA_CMD_NO_RESP 4-Warning [chars]: No response for interface configuration command [dec] A timeout occurred while RP was waiting for a response from line card. This may happen due to line card CPU being too busy to respond to the command. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_RP_SPA-4-SPA_RESP_CMD_ERR 4-Warning [chars]: Received response to interface configuration command [chars] with wrong return value [dec]. An internal error occurred while configuring the interface. The configuration may not have succeeded. DDTS_COMPONENT "Check that the running configuration for the " "interface is correct. If this message is repeatable please " LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-4-SPA_RESP_CMD_MISMATCH 4-Warning [chars]: Expecting response to interface configuration command [dec] but received response to command [dec]. An internal synchronization error occurred while configuring the interface. The configuration may not have succeeded. DDTS_COMPONENT "Check that the running configuration for the " "interface is correct. If this message occurred on the standby try " "reloading the standby to ensure that its configuration is in sync. " "If this message is repeatable please " LOG_STD_SH_TECH_ACTION IOSXE_RP_SPA-6-CARDRELOAD 6-Information Module [dec] reload due to SPA insert in [dec]/[dec]. When inserting a SPA on this carrier card the card is reset. - LOG_STD_NO_ACTION IOSXE_RP_SPA-6-CTRLRSWITCH 6-Information switching controller type from [chars][dec] to [chars][dec] for subslot [dec]/[dec]. When IOSXE-SIP40 is inserted in the slot previously occupied by IOSXE-SIP10 or vice-versa the controller type of the card is overwritten to reflect the current SIP. - LOG_STD_NO_ACTION IOSXE_RP_SPA-6-MEDIA_AUTOFAILOVER 6-Information Media Fail over from [chars] to [chars] Gige Media Failover. - "This is inforamtional message Not an error message." "Use 'show interface gig'" "to see the current active media type." IOSXE_RP_VTYMGT-3-MSGBIPCBUFFER 3-Error Unable to acquire a BIPC buffer of length [dec] for sending messages. A message was to be sent by IOS but no BIPC buffer was available. The message to be sent has been discarded and the associated operation failed. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGBIPCERR 3-Error Unable to process received BIPC messages for Vty Management error: [chars] An unexpected condition has occurred while IOS was trying to process a received BIPC message for Vty Management. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGBUILDERROR 3-Error Error '[dec]' building TDL Vty Management message '[chars]': [chars] An unexpected condition has occurred while IOS is building a TDL response message for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGDISPATCH 3-Error Unable to dispatch received TDL messages for Vty Management An unexpected condition has occurred while IOS is trying to dispatch to the TDL message handler functions for received TDL messages for Vty Management. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGDISPATCHNULL 3-Error Received NULL TDL message An unexpected condition in which IOS has received a NULL TDL message for Vty Management. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGENQUEUEERROR 3-Error Error queueing TDL Vty Management message '[chars]' An unexpected condition has occurred when IOS attempted to queue a TDL response message for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGERROR 3-Error Error '[dec]' handling a received TDL message '[chars]' for Vty Management: [chars] An unexpected condition has occurred while IOS is processing a received Vty Management TDL message iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGEXTAPPUPDATE 3-Error Unable to update external application data for line '[dec]' An attempt to update the external application for a line failed unexpectedly. The line update failed and if the line number specified is valid the line was released. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGINVALIDFIELDINT 3-Error Invalid field '[chars]' in TDL message '[chars]' received: value '[dec]' for Vty Management A message with an invalid field value was received for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGINVALIDFIELDSTR 3-Error Invalid field '[chars]' value '[chars]' in TDL message '[chars]' received for Vty Management A message with an invalid field value was received for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGMARSHALERROR 3-Error Error '[dec]' marshaling TDL Vty Management message '[chars]': [chars] An unexpected condition has occurred while IOS is marshaling TDL response message for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGMISSINGFIELD 3-Error Missing field '[chars]' in TDL Vty Management message '[chars]' received A message missing a required field was received for Vty Management iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGVTYCOUNT 3-Error Invalid vty count [dec] detected on initialization Upon initialization the Vty Management subsystem checks that the number of available vtys for the platform is valid. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-MSGVTYSVCINIT 3-Error Unable to initialize the Vty Management service listen port The platform IPC services failed to register the Vty Management service's need for a listen port. The Vty Management service will be unable to process requests. IOS services will be unavailable to external access methods. iosxe-shellmgr LOG_STD_ACTION IOSXE_RP_VTYMGT-3-SET_ACCESS_FAIL 3-Error Installing LIIN interface access control failed This error happens when the Vty Management subsystem failed to set the access control function for the LIIN possibly due to IOS out of memory or corruption. Persistent access features into IOS will not work. iosxe-shellmgr LOG_STD_ACTION IOSXE_SCHED-3-AVL_INSERT_FAIL 3-Error Could not insert pid [dec] into process tree An avl_insert failed to add a process structure to the ASR1000 DDTS_COMPONENT LOG_STD_ACTION IOSXE_SCHED-3-BACKOFF_PRODUCER 3-Error Tx data in message queue '[chars]' appears to have stalled. Producer info: '[chars]' pid [dec] current queue depth: [dec] bytes Based upon internal state derived from calls to mcp_queue_produced DDTS_COMPONENT LOG_STD_ACTION IOSXE_SCHED-3-CALLED_FROM_INT 3-Error API call incorrectly made from interrupt level - DDTS_COMPONENT LOG_STD_ACTION IOSXE_SCHED-3-CONTINUE_PRODUCER 3-Error Stall for message queue '[chars]' have been cleared current queue depth: [dec] bytes This is to inform that the condition for a message queue which had previously caused back-off of producer processs has been cleared DDTS_COMPONENT LOG_STD_ACTION IOSXE_SCHED-3-NEGATIVE_DEPTH 3-Error Queue '[chars]' consumed more than it produced [dec] - - - IOSXE_SCHED-3-NULLQ 3-Error Invalid API parameter An external routine provided by the ASR1000 scheduler was incorrectly called with an invalid NULL pointer. DDTS_COMPONENT LOG_STD_ACTION IOSXE_SDWAN_CONFIG-2-MASTER_KEY_FAILED 2-Critical A new type 6 encryption master key has failed to generate A type 6 encryption master key was not found on this device. A new key failed to generate. cedge-dfp LOG_STD_DDTS_TAC_DETAILS IOSXE_SDWAN_CONFIG-3-MASTER_KEY_MISSING 3-Error Type 6 master key is missing. A new key will be generated. - cedge-dfp LOG_NO_ACTION IOSXE_SDWAN_CONFIG-4-KEY_ENCRYPT_CHANGE 4-Warning A type 7 key was detected for [chars] which supports type 6. Re-encrypting to type 6. A type 7 key was configured. Type 7 usage is discouraged when the component also supports type 6. The type 7 key will be descripted and re-encrypted to type 6. cedge-dfp LOG_NO_ACTION IOSXE_SDWAN_CONFIG-4-MASTER_KEY_GENERATED 4-Warning A new type 6 encryption master key has been generated. A type 6 encryption master key was not found on this device. A new key has been generated. cedge-dfp LOG_NO_ACTION IOSXE_SDWAN_CONFIG-5-MASTER_KEY_PRESENT 5-Notice Type 6 master key is present on the device. A type 6 key encryption has been requested by config-manager and an existing type 6 master key will be used for encryption/decryption. cedge-dfp LOG_NO_ACTION IOSXE_SERVICE_ENGINE-3-MSGINITFAIL 3-Error Initialization of interface [chars] failed The initialization of the interface mentioned in the error message has failed. DDTS_COMPONENT LOG_STD_ACTION IOSXE_SERVICE_ENGINE-3-MSGOPENFAIL 3-Error Cannot open interface [chars] [dec] During the creation of a Service-Engine interface it is necessary to program the system parameters in the driver. The driver cannot be opened. DDTS_COMPONENT LOG_STD_ACTION IOSXE_SERVICE_ENGINE-3-MSGSETFAIL 3-Error Set id on interface [chars] [dec] During the creation of a Service-Engine interface it is necessary to program the system parameters in the driver. The failed to accept the programming. DDTS_COMPONENT LOG_STD_ACTION IOSXE_SERVICE_ENGINE-5-SRVENGNOTAVL 5-Notice Service Engine Not Available The Service Engine Not Available. - LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-APS_CFG_FAIL 3-Error Failed to configure APS on [chars]: [chars]. The SPA driver failed to configure APS on an interface. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-APS_PGP_FAIL 3-Error APS PGP Message send failed toslot/tobay [dec]: [dec]. The SPA ETHER process is not able to write to ezman as ezman is blocked for writes. Copy the error message exactly as it appears and report it to your technical support representative. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-ASR1000IPCALLOCFAIL 3-Error Failed to allocate Common IPC buffer [chars] The Carrier Card failed to allocate a buffer for\n\ communication with the Route Processor. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-BAD_IFCOMTYPE 3-Error Bad ifcom message type=[dec] - asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-BADMALUCMD 3-Error Unsupported MALU command [dec] arg=[hex] pascb=[hex] - asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-BADMALUCMD2 3-Error Unsupported MALU cmd/arg0=0x%04x%04x arg1arg2=0x%04x%04x hwidb=[chars] - asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-C2W_MAIN_INIT_FAIL 3-Error Failed to initialize SPA main c2w bus for subslot [dec] status = [dec] The SPA driver is not able to initialize SPA main c2w. This indicates a hardware error. asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-CMDNOINT 3-Error HWIDB Null for command [dec] port [hex] The Route Processor passed down a port number that is unknown on the\n\ carrier card. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-DEVICE_ERROR 3-Error subSlot [dec] spatype 0x[hec]. Device error: [chars] An error related to a device on the SPA is detected. asr1k-spa-infra LOG_STD_SH_TECH_ACTION IOSXE_SIP_SPA-3-EFC_CHAN_ERR 3-Error EFC error - interface [chars] vc [dec] anyphy [dec] err_code [dec] : [chars] Failed to configure efc channel/parameters asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-EFC_FC_MAP_FAIL 3-Error Failed to update EFC flow control identifier for interface [chars] status = [dec] The SPA driver is not able to update the datapath EFC flow control identifier for the interface specified in the message. This indicates a hardware error. asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-EFC_PROV_FAIL 3-Error Failed to provision EFC for interface [chars] status = [dec] The SPA driver is not able to provision EFC for the interface specified in the message. This indicates a hardware error. asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-EFC_UNPROV_FAIL 3-Error Failed to unprovision EFC for VC [chars] status = [dec] The SPA driver is not able to unprovision EFC for the interface specified in the message. This indicates a hardware error. asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-FAST_NOTIFY_ERROR 3-Error Failed to send fast notification to [chars] for [chars] [chars]. The SPA driver failed to deliver a fast notification. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-FCI_NOT_SET 3-Error Bay [dec] - FCI type not set An FCI type of zero was detected asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-FRR_CFG_FAIL 3-Error Failed to configure fast reroute on [chars]: [chars]. The SPA driver failed to configure fast rerouting on an interface. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-HWIDB_FAILURE 3-Error Creation: port [dec] vc [dec] Failed to create a hwidb. asr1k-spa-infra LOG_STD_SH_TECH_ACTION IOSXE_SIP_SPA-3-INVALID_ANYPHY 3-Error Bay [dec] - Invalid anyphy number [dec] for vc [dec] Interface has invalid anyphy mumber asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." IOSXE_SIP_SPA-3-INVALID_IF 3-Error Attempted to access HWIDB for port [dec] on slot [dec] subSlot [dec] The ASR1000 attempted to access the HWIDB associated with\n\ a non-existent port. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-IPCALLOCFAIL 3-Error Failed to allocate IPC buffer [chars] The SPA failed to allocate a buffer for communication with\n\ the Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-IPCPORT 3-Error Failed to [chars] IPC port '[chars]' error [chars] The Linecard failed to create a port for\n\ communication with the Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-IPCPORT 3-Error Failed to [chars] IPC port '[chars]' error [chars] The Linecard failed to create a port for\n\ communication with the Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-IPCPORTFAIL 3-Error Failed to open IPC port '[chars]' [chars] with error [chars] The RP failed to open a port for communication with a SPA\n\ module. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-IPCPORTFAIL 3-Error Failed to open IPC port '[chars]' [chars] with error [chars] The RP failed to open a port for communication with a SPA\n\ module. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The Linecard failed to send a message to the\n\ Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-IPCSENDFAIL 3-Error Failed to send IPC message [chars] The Linecard failed to send a message to the\n\ Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-ISR_RC_ERROR 3-Error ISR return code out of range. rc=[dec] The ISR error return code is out of range. asr1k-spa-infra LOG_STD_SH_TECH_ACTION IOSXE_SIP_SPA-3-LINKREC_ERROR 3-Error Link record error - Bay [dec] vc [dec] error code [dec] Error processing link record structure asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance open a case with the Technical Assistance " "Center via the Internet at " " http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." IOSXE_SIP_SPA-3-LVLTRTOOBIG 3-Error Loveletter length exceeds max [dec] bytes The ASR1000-SIP line card attempted to send a large message to the\n\ Route Processor ASR1000-RP. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-MESSAGE_ERROR 3-Error Bay [dec]: [chars] An unexpected error has occurred. asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-NETCLK_FAIL 3-Error Failed to [chars] SPA reference clock on [chars] The SPA driver is not able to correctly configure the SPA reference clock on the specified interface. This indicates a hardware error. asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-NODISPATCH 3-Error Dispatch vector Null cmd=[dec] dintf=[dec] No command dispatch vector was found for the specified interface. asr1k-spa-infra "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IOSXE_SIP_SPA-3-POWER 3-Error Bay [dec] 12V power is [chars] SPA 12V power fault indicator asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-3-SONET_CLOCK_FAILED 3-Error SPA Sonet clock has failed status = 0x%08x The SPA SONET clock has failed. SPAs that rely on the SPA SONET clock for proper operation such as POS and ATM will be affected. asr1k-spa-infra "If the SPA Sonet clock does not recover perform an " "OIR. "LOG_STD_RECUR_ACTION IOSXE_SIP_SPA-3-SONET_CLOCK_RECOVERED 3-Error SPA Sonet clock has recovered status = 0x%08x SPA Sonet clock has recovered asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SIP_SPA-3-SPA_CTRL_EFC_CONFIG_FAILURE 3-Error Subslot spa controller EFC configuration failure error [dec] Failed to configure SPA controller EFC asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-SPA_CTRL_INIT_FAILURE 3-Error Subslot [dec] spa controller initialisation failure error [dec] Failed to initialise SPA controller asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-SPA_INTF_ID_CC_ALLOC_FAILED 3-Error Failed to allocate interface identifiers for SPA [chars] Failed to get CC buffer and flow control identifiers for the SPA in the specified subslot Traffic cannot flow through the SPA under this failure condition. This can happen if the system runs out of available identifiers. asr1k-spa-infra "Try to reduce the number of interfaces" "configured in the system either by physically removing the SPAs" "or by changing the system configuration" IOSXE_SIP_SPA-3-SPI4_CONFIG_FAILURE 3-Error Bay [dec] spi4 configuration failure error [dec] Failed to configure SPI4 interface asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-SPI4_INIT_FAILURE 3-Error Bay [dec] initialization failure Failed to create SPI4 subblock asr1k-spa-infra "Seach for resolved software issues using the Bug " "Toolkit at http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.pl. " "If you still require assistance " LOG_STD_ACTION IOSXE_SIP_SPA-3-SPI4_NOTSYNC 3-Error [chars]: Can not synchronize SPI4 bus host: src [chars]in sync sink [chars]in sync spa: src [chars]in sync sink [chars]in sync. SPI4 bus between modular services card and SPA is not synchronized. It indicates either a not properly seated SPA a hardware failure or an outdated ROMMON/FPGA image. - "Ensure that the SPA is properly seated " "in its subslot and reseat it if required." IOSXE_SIP_SPA-4-MAX_BANDWIDTH 4-Warning Total SPA bandwidth exceeds line card capacity of %lu Mbps The total bandwidth of SPAs exceeds the rated capacity of this line card. asr1k-spa-infra "Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card" IOSXE_SIP_SPA-4-MAX_BANDWIDTH_NS 4-Warning Total SPA bandwidth exceeds line card capacity full utilization of installed SPA interfaces is not supported The total bandwidth of SPAs exceeds the rated capacity of this line card. asr1k-spa-infra "Refer to the line card guidelines for the maximum allowed" "aggregated SPA bandwidth for the line card" IOSXE_SIP_SPA-4-SPABUS 4-Warning Subslot [dec] [chars] SPA BUS access failed. timeout=[dec] err=[dec] par=[dec] err_c=0x[hec] addr=0x%08x data =0x[hec] SPABUS has reported an error. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-4-SPABUS2 4-Warning Subslot [dec] SPA BUS access failed. No SPA present error SPABUS has reported an error. asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-6-LOGGERMSGTOOBIG 6-Information Logger message length [dec] bytes exceeds the maximum allowed size The carrier card attempted to send a large message to the Route Processor asr1k-spa-infra LOG_STD_ACTION IOSXE_SIP_SPA-6-OIR 6-Information Bay [dec] [chars] changed to [chars] SPA OIR Sequence asr1k-spa-infra LOG_STD_NO_ACTION IOSXE_SMART_AGENT-3-NOTIFY_NOT_AUTHORIZED 3-Error Requested count [dec] for license level [chars] is in 'not authorized' state. Authorization Code needs to be installed using 'license smart reservation install' CLI iosxe-smart-agent - IOSXE_SMART_AGENT-3-NOTIFY_OOC 3-Error Pool is out of compliance This pool is Out Of Compliance iosxe-smart-agent "The pool is out of compliance. Customer needs" "to update his license pool" IOSXE_SMART_AGENT-6-NOTIFY_DISABLED 6-Information Smart Licensing is now Disabled Smart Licensing is Disabled iosxe-smart-agent - IOSXE_SMART_AGENT-6-NOTIFY_ENABLED 6-Information Smart Licensing is now Enabled Smart Licensing is Enabled iosxe-smart-agent - IOSXE_SMART_AGENT-6-NOTIFY_GRACEWILLEXPIRE 6-Information Grace Period will Expire Grace Period will expire iosxe-smart-agent - IOSXE_SMART_AGENT-6-NOTIFY_InC 6-Information Pool is now in Compliance Smart Licensing Pool in Compliance iosxe-smart-agent - IOSXE_SMART_AGENT-6-STANDBY_NOT_AUTHORIZED 6-Information Standby is in 'not authorized' state for license [chars] Authorization Code needs to be installed using 'license smart reservation install' CLI on standby iosxe-smart-agent - IOSXE_SPA-3-ABANDON_SPA_CONFIGURATION 3-Error Abandon configuration for subslot [dec]/[dec] the SPA type[dec] is NOT match Abandon SPA configuration. DDTS_COMPONENT "Please check the startup configuration use \"no " "card\" command to override wrong card configuration and update card " "type." IOSXE_SPA-3-CREATE_TDLH_FAILURE 3-Error Failed to create SPA [dec]/[dec] handle Failed to create message handle for SPA communication. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-CREATE_TDLMSG_FAILURE 3-Error Failed to create [chars] message for [chars]. Failed to create/allocate necessary TDL message for SPA communication. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-CREATION_FAILURE 3-Error slot=[dec] subslot=[dec] spa_type=0x[hec] lc_type=0x[hec]. Failed to create a SPA object. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-DIAG_CONFIG 3-Error [chars] did not complete [dec]/[dec] An error has occured during diagnostic test. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-DISPATCH_INIT_TDLH_FAILURE 3-Error Failed to initialize dispatch path for SPA [dec]/[dec] handle Failed to initialize dispatch path handle for SPA communication. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-DOMAIN_TDLH_FAILURE 3-Error [chars] rc = [dec] Failed to bind message handle for SPA communication. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_CPU_NUM 3-Error cpu= [dec] max cpu = [dec] An invalid CPU number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_DATA_INSTANCE 3-Error interface type [chars] slot [dec] port [dec] vc [dec] : [chars] Data required to support the interface is not available. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_DB_NUM 3-Error db = [dec] max db = [dec] db intf = [dec] max db intf = [dec] An invalid daughter board number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_HANDLE 3-Error Failed to get a valid IPC handle for type [dec] slot [dec] subslot [dec]. The client handle was found to be NULL for the given type/slot/subslot. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_IF_INDEX 3-Error index= [dec] spaType=0x[hec] slot [dec] subSlot [dec] slotunit [dec] vc [dec] Index for the interface is not valid. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_INDX_RANGE 3-Error index1= [dec] index2= [dec] maxIndex= [dec] An invalid index range is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_RP_SLOT_NUM 3-Error slot= [dec] max slot = [dec] An invalid RP slot number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_SLOT_NUM 3-Error slot= [dec] max slot = [dec] An invalid slot number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_SLOTUNIT_NUM 3-Error cardwide-port = [dec] max cardwide-port = [dec] An invalid cardwide-port number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_SPA_TDL_CCAPI_USAGE 3-Error - Incorrect usage of an internal API that should only be used on CC. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-INVALID_SUBSLOT_NUM 3-Error subslot= [dec] max subslot = [dec] An invalid subslot number is specified in one of the internal APIs. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-IPC_FAILURE 3-Error IPC failure while [chars] An error has occurred while prepareing or sending an IPC message. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-MEM_ALLOC_ERROR 3-Error [chars] Memory allocation error. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-NULL_BAY_PTR 3-Error - Pointer to SPA bay is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-NULL_SPA_PTR 3-Error - Pointer to a SPA object is NULL. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-NULL_VFT 3-Error [chars] virtual function table is not initialized. spaType=0x[hec] A required function table is not initialized DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-NULL_VFUNC 3-Error [chars] vector is not initialized. spaType=0x[hec] A required function vector is not initialized DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-POWER_CYCLE 3-Error [chars] occurred on Shared Port Adapter [dec]/[dec] An error has occurred which will cause the \n\ Shared Port Adapter to be power cycled DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-SENDCFGFAIL 3-Error Failed to send configuration for [chars] to carrier-card for subslot=[dec]/[dec] Sending configuration failed. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-SETUP_TDLH_FAILURE 3-Error Failed to set the alloc/free handler for SPA [dec]/[dec] handle Failed to set the alloc/free handler for SPA communication. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-SPA_CREATION_FAILURE 3-Error slot=[dec] subslot=[dec] PID=[chars] lc_type=0x[hec]. Failed to create a SPA object. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-SPA_SETUP_FAILURE 3-Error Failed to properly setup for SPA communication on slot [dec] subslot [dec]. Discovery of the linux interface used to communicate with a SPA failed DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-3-UNSUPPORTED_DATA 3-Error Data conversion error [chars] 0x%X An internal software error has occured when converting the data specified in the message from one representation to another. DDTS_COMPONENT LOG_STD_SH_TECH_ACTION IOSXE_SPA-4-COMMUNICATION_DISCONNECTED 4-Warning Communication with IM in [dec]/[dec] stalled. Retrying. IM will reboot if situation persists Retransmit IPC communication request between IOS and IOMD. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_SPA-4-COMMUNICATION_ESTABLISHED 4-Warning Communication with IM in [dec]/[dec] restored. IPC communication between IOS and specified IM has been restored. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_SPA-6-DUAL_RATE_CHANGE 6-Information [chars]: [chars] Change in rate of the link. DDTS_COMPONENT LOG_STD_NO_ACTION IOSXE_SPA-6-TDLMSG_INCOMPATIBLE 6-Information Failed to copy message [chars] to buffer not allowed for current domain. Failure to marshal a message indicates an incompatibility with the intended recipient. iosxe-spa-infra LOG_STD_SH_TECH_ACTION IOSXE_SPA-6-UPDOWN 6-Information Interface [chars] link down due to [chars] Ethernet link is down due to remote/local fault. DDTS_COMPONENT "Replace the faulty cable." IOSXE_SPA-6-UPDOWN1 6-Information Interface [chars] link down due to [chars] [chars][dec].[dec] dbm Ethernet link is down due to mac LF/RF/phy line/host side fault. Optics Rx power is ok/low/hi DDTS_COMPONENT "Debug mac/phy/optics block" IOSXE_SPA-6-UPDOWN2 6-Information Interface [chars] link down due to [chars] [chars][dec] Ethernet link is down due to macLF/RF/phy line/hostside fault. Dom is not supported by the optics DDTS_COMPONENT "Debug phy/optics block" IOSXE_SPA-6-UPDOWN3 6-Information Interface [chars] link down due to [chars] ln0:[chars][dec].[dec] dbmln1:[chars][dec].[dec] dbmln2:[chars][dec].[dec] dbmln3:[chars][dec].[dec] dbm Ethernet link is down due to macLF/RF/phy line/host side fault. Optics Rx power lane is ok/low/high. DDTS_COMPONENT "Debug phy/optics block" IOSXE_SPA-6-UPDOWN4 6-Information Interface [chars] link down due to [chars] -40dbm Ethernet link is down due to macLF/RF/phy line/host side fault.Optics Rx power is zero. DDTS_COMPONENT "Debug mac/phy/optics block" IOSXE_SPA-6-UPDOWN5 6-Information Interface [chars] link down due to [chars] ln0:[chars][dec].[dec] dbmln1:[chars][dec].[dec] dbmln2:[chars][dec].[dec] dbmln3:[chars][dec].[dec] dbmln4:[chars][dec].[dec] dbmln5:[chars][dec].[dec] dbmln6:[chars][dec].[dec] dbmln7:[chars][dec].[dec] dbmln8:[chars][dec].[dec] dbmln9:[chars][dec].[dec] dbm Ethernet link is down due to macLF/RF/phy line/host side fault. Optics Rx power lane is ok/low/high. DDTS_COMPONENT "Debug phy/optics block" IOSXE_SUBSYS_EX-2-SUBSYS_EX_INIT_FAIL 2-Critical Subsys exclusion init failed. Invalid subsys list. Fail to initialize excluded subsystems to NULL. \n\ an abnormal condition DDTS_COMPONENT "This message means a software error had happened. \n" "The list of subsystems to be removed is not initialized. \n" "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative" IOSXE_SUBSYS_EX-2-SUBSYS_LIST_NOT_TERMINATED 2-Critical Subsystems in exclusion list is not terminated correctly. The subsystem exclusion list is not termianted \ by a NULL entry. \n It is \ an abnormal condition DDTS_COMPONENT "This message may be related to a memory corruption or hardware issue.\n\ \n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative" IOSXE_SUBSYS_EX-2-SUBSYS_REMOVE_FAIL 2-Critical Unable to remove excluded subsystems. Fail to remove excluded subsystems. \n\ an abnormal condition DDTS_COMPONENT "This message may be related to a memory corruption. \n" "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative" IOSXE_SYS_INFRA-3-BIPC_CREATE_FAIL 3-Error Failed to open IPC port '[chars]' for service '[chars]' with error [chars]. BIPC connect failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-BIPC_DISCONNECT_FAIL 3-Error Failed to disconnect IPC port '[chars]' for service '[chars]' with error [chars]. BIPC disconnect failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_EPOLL_WAIT 3-Error Fastpath thread epoll wait failed errno [dec] Fastpath epoll wait failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_EVDISPATCH 3-Error Fastpath thread event dispatch failed ev_ret [dec] errno [dec] fastpath thread event dispatch failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_EVGETNEXT 3-Error Fastpath thread get next event failed ev_ret [dec] errno [dec] Fastpath thread get next event failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_IPC_EPOLL_CTL_FAILED 3-Error Fastpath thread [chars] [chars] for IPC channel [chars] ipc id [dec] ipc fd [dec] seqnum [dec] failed efd [dec] errno [dec] Fastpath epoll_ctl operation for an IPC channel failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_IPC_EPOLL_NO_IPC_ENTRY 3-Error IPC entry not found for ipc fd [dec] seq [dec] events 0x[hec] while processing [chars] from epoll fd [dec] Fastpath failed to find IPC entry after epoll_wait iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EFP_TOP_EPOLL_CTL_FAILED 3-Error Fastpath thread top level efd epoll [chars] failed fd [dec] errno [dec] Fastpath top level efd epoll_ctl operation failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EIOS_EVDISPATCH 3-Error IOS scheduler event dispatch failed ev_ret [dec] errno [dec] IOS scheduler event dispatch failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EIOS_EVGETNEXT 3-Error IOS scheduler get next event failed ev_ret [dec] errno [dec] IOS scheduler get next event failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EIOS_POLL 3-Error IOS thread poll on event lib and wakeup fds failed errno [dec] IOS thread poll on event lib and wakeup fds failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EOBC_SOCK 3-Error Socket event for [chars] An internal socket level event has returned an error which\n\ is indicated. This may have been the result of a bind\n\ peek receive or send operation with respect to the EOBC\n\ interface listed. iosxe-iosd-infra "show eobc\n\ show platform software\n\ infrastructure bipc" IOSXE_SYS_INFRA-3-EREAD_EVENT_FD 3-Error [chars] read from wakeup fd failed errno [dec] A thread reading from its wakeup fd failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EVLIB_EPOLL_ARGS 3-Error evGetEpollArgs returned fd [dec] Evlib retuned a huge FD value that IOS can not handle. iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-3-EWRITE_EVENT_FD 3-Error Write to [chars] wakeup fd failed errno [dec] current signal/wakeup cnt: %llu/%llu Trigering a thread by writing to its wakeup fd failed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-4-BIPC_CLEAR_CONN 4-Warning IPC channel fd [dec] seq_num [dec] for service '[chars]' cleared by user BIPC disconnect requested by an user with clear command iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-4-BIPC_RX_IN_APPL_THRESHOLD 4-Warning Number of IPC messages held in the application reached the \n\ maximum channel threshold. IPC channel '[chars]': \n\ ipc_ctl_id [dec] ipc_fd [dec] seq_num [dec] curr IPC msg hel in appl [dec] - - - IOSXE_SYS_INFRA-4-BIPC_TX_Q_THRESHOLD 4-Warning BIPC transmit queue threshold reached for the channel '[chars]':\n\ ipc_ctl_id [dec] ipc_fd [dec] seq_num [dec] Tx Q size [dec] - - - IOSXE_SYS_INFRA-6-BIPC_CREATE 6-Information bipc connect succeeded for [chars] ipc_ctl_id [dec] ipc_fd [dec] seq [dec] BIPC connect succeeded iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-BIPC_DISCONNECT 6-Information disconnect by application for [chars] bring down IPC BIPC disconnect requested by an application iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-BIPC_READ_ERR 6-Information connection read error from [chars] rc [dec] bring down IPC id [dec] for fd [dec] seq [dec] BIPC error during IPC read iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-BIPC_READBUF_ERR 6-Information process receive buffer error from [chars] rc [dec] bring down IPC BIPC error during IPC read from buffer iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-BIPC_WRITE_ERR 6-Information write bipc error for [chars] rc [dec] bring down IPC BIPC error during IPC read iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-EOBC_ADDR_CACHE 6-Information EOBC ip-table cache: [chars] Unable to setup internal address for eobc communication iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-FP_IPC_DISCONNECT 6-Information IPC channel disconnect for [chars] ipc_ctl_id [dec] fd [dec] seq_num [dec] loc [chars] err [dec] [chars] An IPC channel in fastpath is terminated iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-IOS_FREE_IPC_CTL 6-Information IPC control blk free: name [chars] ipc_ctl_id [dec] refcount [dec] An IPC control block is freed iosxe-iosd-infra LOG_STD_ACTION IOSXE_SYS_INFRA-6-IOS_IPC_CTL_DESTROY 6-Information IPC control blk destroy: name [chars] ipc_ctl_id [dec] refcout [dec] need_free [dec] An IPC control block is requested to be destroyed iosxe-iosd-infra LOG_STD_ACTION IOSXE_THROUGHPUT-3-CONF_FAILED 3-Error Configuration failed. Installed license does not support the throughput level. Please install the valid license An error occurred when the throughput configuration was attempted. iosxe-csl - IOSXE_THROUGHPUT-3-EULA_NOT_ACCEPTED 3-Error The EULA has to be accepted prior to throughput configuration. Users need to accept EULA to activate the license iosxe-csl "Accept EULA for throughput license" IOSXE_THROUGHPUT-3-INVALID_CONFIG 3-Error No valid license found for the configured throughput level: [chars] kbps Users has the boot up throughput set to non-default level without having the valid license. iosxe-csl "Install valid throughput license" IOSXE_THROUGHPUT-3-INVALID_LEVEL 3-Error An invalid throughput level: [chars] kbps was selected. The configured throughput level is unknown iosxe-csl - IOSXE_THROUGHPUT-3-SETUP_FAILED 3-Error Throughput level setup failed. Boot up will be at the default throughput An error occurred when licensing tried to setup the througput iosxe-csl - IOSXE_THROUGHPUT-6-LEVEL 6-Information Throughput level has been set to [dec]00000 kbps Throughput level has been set to a number iosxe-csl - IOSXE_TIMESTAMP_ENGINE-3-TSU_ERR 3-Error An unexpected condition has occurred at module [chars] An unexpected condition has occurred at the Interface Module TSU. asr900-ptp LOG_STD_ACTION IOSXE_TIMESTAMP_ENGINE-4-ERROR 4-Warning NULL An unexpected condition has occurred. asr900-ptp LOG_STD_ACTION IOSXE_UEA-3-INVALID_EEPROM 3-Error MAC count from BP is supposed to be 512 for NCS. Actual MAC count[dec] For UEA NCS platforms MAC count must be 512 uea-systems "Please program the EEPROM to correct MAC count" IOSXE_USB-3-ESHOW_USB 3-Error Internal Error locating database for USB Devices. The mcp_usb_devices is incorrect and needs to be changed iosxe-iosd-infra LOG_STD_ACTION IOSXE_UTD-2-VERSION_UNSUPPORTED 2-Critical UTD package version \[chars]\ is not supported recommended version is \[chars]\ The UTD package version does not match the required UTD version embedded in this IOS-XE version. This is an unsupported configuration and may behave unexpectedly. iosxe-utd LOG_STD_ACTION IOSXE_UTD-3-ALLOC 3-Error Failed to allocate message When attempting to program the dataplane there was not enough memory to allocate the message. iosxe-utd LOG_STD_ACTION IOSXE_UTD-3-MESSAGE 3-Error Failed to send message When the message was being prepared for sending to the data plane there was an error. iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-MT_CONFIG_DOWNLOAD 4-Warning UTD MT configuration download has [chars] In UTD multitenancy mode the configuration download to the container can take a while. Please be patient. iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-MT_CONTAINER_MESSAGE_NAK 4-Warning Container responded to UTD message with an error: [dec] The container rejected the UTD message iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-MT_CONTAINER_MESSAGE_TIMEOUT 4-Warning UTD message sent to the container has timed out The UTD message sent to the container has timed out. iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-MT_CONTAINER_SESSION_TIMEOUT 4-Warning UTD container download has timed out The container did not respond with an up/down status before the session timed out. iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-MT_CONTAINER_STATUS_DOWN 4-Warning UTD poll: container status is DOWN The container sent a down status to the poll message iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-OVA_DEPRECATION 4-Warning The UTD OVA is being deprecated in an upcoming release. Please migrate to IOX to use the UTD TAR The UTD OVA is being deprecated in an upcoming release. Support for the virtual-service command suite will end. To use UTD going forward please migrate to IOX infrastructure. See the 'Migrating to IOx Container' section on the following link for more information: http://cs.co/UtdSnortIPS iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-SIG_UPDATE_CFG 4-Warning UTD signature updates have been configured - A brief service interruption at the time of update is expected The UTD service will be restarted if a new signature package is found. During this time if fail-close has been configured recommended traffic that would be inspected by iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-SIG_UPDATE_CFG_INCOMPLETE 4-Warning UTD signature update configuration is incomplete UTD signature updates have been partially configured. Both the signature update server and occur-at frequency are required. iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-SIG_UPDATE_EXEC 4-Warning UTD signature update has been executed - A brief service interruption is expected The UTD service will be restarted if a new signature package is found. During this time if fail-close has been configured recommended traffic that would be inspected by iosxe-utd LOG_STD_ACTION IOSXE_UTD-4-VERSION_INCOMPATIBILITY 4-Warning UTD package version \[chars]\ does not match recommended UTD package version \[chars]\ The UTD package version does not match the recommended UTD package version embedded in this IOS-XE version. iosxe-utd LOG_STD_ACTION IOSXE_VMAN-3-MSGDISPATCH 3-Error Unable to dispatch received TDL message from Virt-manager An unexpected condition has occurred while IOS was trying to dispatch a TDL message received from Virt-manager. vman LOG_STD_ACTION IOSXE_VMAN-3-MSGINITFAIL 3-Error Failed to initialize required Virt-manager resource: [chars] During the initialization of the resources required by Virt-manager a failure occurred. This has prevented virtual services from being activated. vman LOG_STD_ACTION IOSXE_VMAN-3-RSPMSGHDLR 3-Error Failed to deliver response message: [chars] An unexpected condition has occurred while IOS was trying to deliver a response message to a virtual service received from Virt-manager. vman LOG_STD_ACTION IOSXE_WCCP-4-ACELIMIT 4-Warning Too many ACEs in MASK ACL please switch to Hash mode Mask merged ACL generate too many ACEs. asr1k-wccp "show ip access-lists" IOSXE_WCCP-4-BADACE 4-Warning Access list contains invalid ace An unexpected condition has occurred which is due to an invalid\n\ statement in the access list structure. asr1k-wccp "show ip access-lists" IOSXE_WCCP-4-NOACL 4-Warning Access list is null An unexpected condition has occurred which is due to the absence of\n\ an access list structure. asr1k-wccp "show ip access-lists" IOSXE_WCCP-4-NOINPUT 4-Warning NULL input [chars] An unexpected condition has occurred which is due to the NULL value\n\ of the input parameter. asr1k-wccp "show ip wccp" IOSXE_WCCP-4-NOINTF 4-Warning No [chars] interface info for Service Group [dec] [dec] [dec] An unexpected condition has occurred which is due to the absence of\n\ MCP WCCP interface info for the specific service group. asr1k-wccp "show platform software wccp" IOSXE_WCCP-4-NOSTATS 4-Warning WCCP [chars] message error An unexpected condition has occurred which is due to the error in \n\ receiving WCCP stats update message. asr1k-wccp "show platform software wccp counters" IOSXE_WCCP-4-NOSTATSINTF 4-Warning Interface handle [dec] not exsit for the stats message An unexpected condition has occurred which can't find the interface handle\n\ for the interface stats message. asr1k-wccp "show platform software wccp int counters" IOSXE_WCCP-4-NOSTATSSVC 4-Warning Service Group [dec] [dec] [dec] not exist for the stats message An unexpected condition has occurred which can't find the service group\n\ for the service group stats message. asr1k-wccp "show platform software wccp" IOSXE_WCCP-4-NOSVCGRP 4-Warning [chars] Service Group [dec] [dec] [dec] NOT exist An unexpected condition has occurred which is due to the absence of\n\ the service group structure. asr1k-wccp "show ip wccp" IOSXE_WCCP-4-UNKNOWNDIR 4-Warning Unknown [chars] interface direction 0x[hec] for Service Group [dec] [dec] [dec] An unexpected condition has occurred which is due to the unknown direction\n\ has been applied to the interface for the service group. asr1k-wccp "show platform software wccp" IOSXE_WD-2-HEARTBEAT_FAIL 2-Critical Heartbeat is not emitted. Heartbeat count:[dec] Failure in IOS to generate a heartbeat is\n\ an abnormal condition DDTS_COMPONENT "This message may be related to an abnormal configuration\n\ and system load or transient high processing demand." "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative" IOSXE_WD-2-HOG_DETECT_FAIL 2-Critical CPUHOG detection failed to start. Failure in setting up CPUHOG detection mechanism is\n\ an abnormal condition DDTS_COMPONENT "This message may be related to an abnormal configuration\n\ and system load or transient high processing demand." "\n\n When reporting this message copy the message text exactly as\n\ it appears include the stack trace and report to your technical\n\ support representative" IOXN_APP-3-CFGFAIL 3-Error [chars] [chars] An unexpected condition resulted into failure to apply auto config iox-caf LOG_STD_ACTION IOXN_APP-3-CLEANUPFAIL 3-Error Failed to create chasfs property to indicate cleanup of previous app installation rc = [chars] - - - IOXN_APP-3-GSFAIL 3-Error [chars] [dec] An unexpected condition resulted into failure to start an application. iox-caf LOG_STD_ACTION IOXN_APP-3-INITFAIL 3-Error Failed to create chasfs property ioxman rc =[chars] or caf rc = [chars] is not up - - - IOXN_APP-3-IOX_CONFIG_FAIL 3-Error IOX configuration change not allowed while running\n Error in iox configuration - LOG_STD_ACTION IOXN_APP-3-IPCINITFAIL 3-Error [chars]\n A critical IPC initialization error occured iox-caf LOG_STD_ACTION IOXN_APP-3-MSGFAIL 3-Error Message dispatch failure [chars]. - - - IOXN_APP-3-PREVOPFAIL 3-Error Overriding previous operation [chars] iox that is taking longer than [dec] An unexpected condition resulted in failure to apply iox config iox-caf LOG_STD_ACTION IOXN_APP-3-STARTUP_CONFIG_FAIL 3-Error [chars] [chars]\n Error while creating startup config - LOG_STD_ACTION IOXN_APP-6-APP_HOSTING_SUPPORT 6-Information [chars] Informational logs to show App Gigabit Interface is not supported on 10 Slot Catalyst 9400 - LOG_STD_ACTION IOXN_APP-6-IOX_START_STOP_REQ 6-Information [chars]\n Informational logs for IOX Start/Stop request. - LOG_STD_ACTION IOXN_APP-6-LICENCE_CHECK_INFO 6-Information [chars]\n Informational log about license. - LOG_STD_ACTION IOXN_APP-6-PRE_INIT_DAY0_GS_INFO 6-Information [chars]\n Informational logs for Day0 GS initialization. - LOG_STD_ACTION IOXN_APP-6-SLOT_NOTIFICATION 6-Information [chars] [dec] Slot addition or removal information - LOG_STD_NO_ACTION IOXN_APP-6-STARTUP_CONFIG_CHASSIS_INFO 6-Information [chars] [dec]/[chars]/[dec]/[dec]\n Chassis information at startup config injection. - LOG_STD_NO_ACTION IOXN_APP-6-STARTUP_CONFIG_INFO 6-Information [chars]\n Informational logs for startup config injection. - LOG_STD_ACTION IP_DEVICE_TRACKING_HA-3-FAIL_SEND_MSG_TO_ACTIVE 3-Error Failed to send [chars] message to active for [chars] [chars] The specified synchronization message which is an internal IPC message could not be sent to the active unit in the specified run-time module. The failure most likely occurred because of a software error. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized. - LOG_STD_SH_TECH_ACTION IP_DEVICE_TRACKING_HA-3-NO_RESOURCES 3-Error [chars] A run-time module could not obtain the resources that are required to complete a task. The failure most likely occurred because of a software error or a lack of system memory. Additional details on the nature of the error are specified in the message text on the console or in the system log. The system state between the active and standby units might not be properly synchronized. - "If you determine that this condition was caused by " "a lack of system memory reduce system activity to " "ease memory demands or if conditions warrant upgrade " "to a larger memory configuration. Otherwise " LOG_STD_SH_TECH_ACTION IP_DEVICE_TRACKING_HA-4-ENTRY_OUT_OF_SYNC 4-Warning Host mac-address [enet] ip-address [inet] interface [chars] event_type: [chars] entry_type: [chars] An inconsistency has been detected in the IP device tracking table for this host between active and standby - LOG_STD_NO_ACTION IP_DEVICE_TRACKING-4-TABLE_LOCK_FAILED 4-Warning Table already locked by process-id [dec][chars] The IP device tracking table could not be updated due to a lock held by another process - LOG_STD_NO_ACTION IP_HOST_ISSU-2-GET_BUFFER 2-Critical IP Host ISSU client failed to get buffer for message. Error: [dec] [chars] The IP Host ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. - "show logging and show checkpoint client" IP_HOST_ISSU-2-INIT 2-Critical IP Host ISSU client initialization failed to [chars]. Error: [dec] [chars] The IP Host ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. - LOG_STD_ACTION IP_HOST_ISSU-2-SEND_NEGO_FAILED 2-Critical IP Host ISSU client failed to send negotiation message. Error: [dec] [chars] The IP Host ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. - "show logging and show checkpoint client" IP_HOST_ISSU-2-SESSION_NEGO 2-Critical IP Host ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The IP Host ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. - "show issu session and " "show issu negotiated capability " IP_HOST_ISSU-2-SESSION_REGISTRY 2-Critical IP Host ISSU client failed to register session information. Error: [dec] [chars] The IP Host ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. - "show issu capability entries and " "show issu session and " "show issu negotiated capability " IP_HOST_ISSU-3-CAP_INVALID_SIZE 3-Error IP_HOST ISSU client capability list is empty. The IP_HOST ISSU client capability exchange list size is invalid. - "show issu capability entires " IP_HOST_ISSU-3-CAP_NOT_COMPATIBLE 3-Error IP Host ISSU client capability exchange result incompatible. The IP Host ISSU client capability exchange have negotiated as incompatible with the peer. - "show issu negotiated capability " IP_HOST_ISSU-3-INVALID_SESSION 3-Error IP Host ISSU client does not have a valid registered session. The IP Host ISSU client does not have a valid registered session. - "show issu capability entries and " "show issu session and " "show issu negotiated capability " IP_HOST_ISSU-3-MSG_NOT_OK 3-Error IP Host ISSU client 'Message Type [dec]' is not compatible The IP Host ISSU client received an incompatible message from the peer device. The message cannot be processed. - "show issu message group and " "show issu session and " "show issu negotiated version " IP_HOST_ISSU-3-MSG_SIZE 3-Error IP Host ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The IP Host ISSU client failed to calculate the MTU for the specified message. The IP Host ISSU client is not able to send the message to the standby device. - "show issu message group and " "show issu session and " "show issu negotiated version " IP_HOST_ISSU-3-SESSION_UNREGISTRY 3-Error IP Host ISSU client failed to unregister session information. Error: [dec] [chars] The IP Host ISSU client failed to unregister session information. - "show issu session and " "show issu negotiated capability " IP_HOST_ISSU-3-TRANSFORM_FAIL 3-Error IP Host ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The IP Host ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the IP Host state between the active device and the standby device is not identical. - "show issu session and " "show issu negotiated version " IP_PORT_SECURITY-4-DENY_INVALID_PACKET 4-Warning Detected and dropped illegal traffic on port [chars] and vlan [dec] the non-cumulative packet dropped count is %ld. IP Port Security only permits traffic with the correct source IP to MAC\n\ binding on the port or VLAN. There may be a malicious host trying to\n\ carry out a denial of service attack using another host's source address.\n\ The illegal traffic is dropped by the IP Port Security feature. ipsg "Identify the source of the illegal traffic " "and stop it." IP_SNMP-3-SOCKET 3-Error can't open UDP socket The SNMP server was unable to open a port for receiving or\n\ transmitting SNMP requests. This usually happens when the SNMP\n\ server is started using the snmp-server community configuration\n\ command on a router or communication server with an interface that\n\ has no IP address configured. Another possible cause is low memory. - "Configure at least one interface with an IP address or specify the no\n\ snmp-server command to remove the SNMP server process. Call your\n\ technical support representative if problems persist or if it becomes\n\ necessary to add memory." IP_SNMP-4-NOTRAPIP 4-Warning SNMP trap source [chars] has no ip address The user entered an snmp-server trap-source command. The interface\n\ requested for use as the source address has no ipv4 address\n\ associated with it. The SNMP trap is being sent anyway but\n\ without the source address that the user intended. - "There are two possible solutions. Either enter a no snmp-server\n\ trap-source command to disable the request for a specific source IP\n\ address or add an IP address to the interface referenced in the\n\ snmp-server trap-source configuration command." IP_SNMP-4-NOTRAPIPV6 4-Warning SNMP trap source [chars] has no ipv6 address The user entered an snmp-server trap-source command. The\n\ interface requested for use as the source address has no ipv6\n\ address associated with it. The SNMP trap is being sent\n\ anyway but without the source address that the user intended. - "There are two possible solutions. Either enter a no snmp-server\n\ trap-source command to disable the request for a specific source\n\ IP address or add an IPV6 address to the interface referenced\n\ in the snmp-server trap-source configuration command." IP_SNMP-4-TOOBIG 4-Warning Oversize message from [inet] datagram size [dec] udp length [dec] An incoming SNMP packet had a length field so large that\n\ the system had to assume it was in error. This system made a\n\ correct reaction to bad external data.\n\ Since SNMP packets should originate from systems under the\n\ same administration this may indicate that the network host\n\ used to originate the SNMP request had a problem in its\n\ networking layer.\n\ Alternatively if the SNMP packet originated from outside\n\ the local administrative domain it could indicate an\n\ failed attempt at security penetration and that site should\n\ be watched more closely. - "If the origin is local no action is required.\n\ If the origin is determined to be malicious either contact the\n\ administrator of the originating site or install filters to\n\ prevent access by that site as circumstances warrant." IP_SOURCE_GUARD-4-DENY_INVALID_PACKET 4-Warning Detected and dropped illegal traffic on port [chars] and vlan [dec] the non-cumulative packet dropped count is %ld. IP Source Guard only permits traffic with the correct source IP to MAC\n\ binding on the port or VLAN. There may be a malicious host trying to\n\ carry out a denial of service attack using another host's source address.\n\ The illegal traffic is dropped by the IP Source Guard feature. ipsg "Identify the source of the illegal traffic " "and stop it." IP_TUNNEL-2-IPC_INIT 2-Critical IPC message handler registration failure rc [dec] Registering an IPC message handler for the Tunnel feature failed. This may cause the feature to not function. qfp-ip-tunnel "This is normally a software issue. " "The consequences are that the tunnel feature may not function. " LOG_STD_ACTION IP_TUNNEL-3-IPC_NORES 3-Error No space for the IPC reply size [dec] For a request from upper TUNNEL software stack layers it was not possible to allocate space for a reply for the specified size. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-ip-tunnel "This is normally a software issue. " LOG_STD_RECUR_ACTION IP_TUNNEL-3-IPC_OPEN_REPLY 3-Error IPC Open Reply failed request [dec] For a request from upper TUNNEL software stack layers it was not possible to open the reply buffer. The consequence of this could be a stuck monitor that cannot be established etc. In rare cases this could also affect other operations such as feature activation. qfp-ip-tunnel "This is normally a software issue. " LOG_STD_RECUR_ACTION IP_TUNNEL-3-VRF_HOST_MEM_EXTEND_FAILED 3-Error QFP TUNNEL Proxy IPC VRF host mem extend failed Extending memory failed. qfp-tunnel keyword:tunnel LOG_STD_ACTION IP_TUNNEL-3-VRF_HOST_MEM_REQ_FAILED 3-Error QFP TUNNEL Proxy IPC VRF host mem req failed Requesting more memory failed. qfp-tunnel keyword:tunnel LOG_STD_ACTION IP_TUNNEL-4-INVALID_MSG_LEN 4-Warning QFP TUNNEL Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Cisco internal software error. QFP TUNNEL Proxy received invalid IPC message length from control plane. This message will be ignored. qfp-tunnel keyword:tunnel LOG_STD_ACTION IP_VFR-3-INVALID_FRAG_LENGTH 3-Error [chars]: fragment length invalid - received from [inet] destined to [inet] This message indicates that the router has encountered a ping-of-death sort of an attack ios-firewall "To prevent further attacks its highly recommendated that an ACL " "be configured to drop any traffic from the sender" IP_VFR-3-OVERLAP_FRAGMENTS 3-Error [chars]: from the host [inet] destined to [inet] This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment. ios-firewall "This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender" IP_VFR-3-SYSTEM_ERROR 3-Error [chars]: IP VFR System failure - [chars] This message indicates the misc errors in the VFR subsystem ios-firewall - IP_VFR-4-FRAG_TABLE_OVERFLOW 4-Warning [chars]: the fragment table has reached its maximum threshold [dec] This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ip virtual-reassembly max-reassemblies ios-firewall - IP_VFR-4-TINY_FRAGMENTS 4-Warning [chars]: from the host [inet] destined to [inet] This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header ios-firewall "This is an informational message" IP_VFR-4-TOO_MANY_FRAGMENTS 4-Warning [chars]: Too many fragments per datagram more than [dec] - sent by [inet] This message indicates the datagram being reassembled has received more fragments than its threshold value ios-firewall "Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ip virtual-reassembly max-fragments " IP_VRF-3-MAX_VRF 3-Error [chars] Related to MAX number of VRFs vrfinfra LOG_STD_ACTION IP_VRF-3-MAX_VRF 3-Error [chars] Related to MAX number of VRFs vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_AF_ACTIVATE 3-Error Unable to activate VRF support for address family [chars] The VRF subsystem was unable to initialize support for the indicated address family vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_AF_ACTIVATE 3-Error Unable to activate VRF support for address family [chars] The VRF subsystem was unable to initialize support for the indicated address family vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_AF_ENABLE_ERROR 3-Error Failed to enable address-family [chars] in VRF [chars]: [chars] Failed to enable AF in a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_AF_ENABLE_ERROR 3-Error Failed to enable address-family [chars] in VRF [chars]: [chars] Failed to enable AF in a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CCA_ERROR 3-Error VRF-CCA: [chars] VRF manager encountered a command inheritance error vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CCA_ERROR 3-Error VRF-CCA: [chars] VRF manager encountered a command inheritance error vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CMN_INVALID_PARAM 3-Error [chars] Invalid parameter. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CMN_INVALID_PARAM 3-Error [chars] Invalid parameter. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CONFIG_IF_LOCK_ERROR 3-Error Failed to acquire interface configuration lock VRF interface association failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CONFIG_IF_LOCK_ERROR 3-Error Failed to acquire interface configuration lock VRF interface association failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CREATE_FAIL 3-Error [chars] IP VRF creation failed. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_CREATE_FAIL 3-Error [chars] IP VRF creation failed. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_GET_LOCK_COUNT_ERROR 3-Error Failed to get lock count for VRF [chars]: [chars] Failed to lock count from a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_GET_LOCK_COUNT_ERROR 3-Error Failed to get lock count for VRF [chars]: [chars] Failed to lock count from a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_HDVRF_ERROR 3-Error HDVRF: [chars] HDVRF related error messages vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_HDVRF_ERROR 3-Error HDVRF: [chars] HDVRF related error messages vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_ID_INVALID_ERROR 3-Error Invalid VRF id 0x[hec] in [chars] VRF ID Invalid vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_ID_INVALID_ERROR 3-Error Invalid VRF id 0x[hec] in [chars] VRF ID Invalid vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_ADD 3-Error Error adding [chars] to interface list of VRF [chars] VRF interface association failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_ADD 3-Error Error adding [chars] to interface list of VRF [chars] VRF interface association failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_DEL 3-Error Error removing [chars] from interface list of VRF [chars] VRF interface disassociation failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_DEL 3-Error Error removing [chars] from interface list of VRF [chars] VRF interface disassociation failed vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_NOT_EMPTY 3-Error VRF [chars] iflist is not empty in [chars] VRF iflist is not empty vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IFLIST_NOT_EMPTY 3-Error VRF [chars] iflist is not empty in [chars] VRF iflist is not empty vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IVRF_ERROR 3-Error [chars] VRF infrastructure failure for Platform VRFs. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_IVRF_ERROR 3-Error [chars] VRF infrastructure failure for Platform VRFs. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LCKMGR_CONTEXT_INIT_ERROR 3-Error Failed to initialize lock manager context for vrf [chars][dec] with error [chars] VRF lock manager initialization failure vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LCKMGR_CONTEXT_INIT_ERROR 3-Error Failed to initialize lock manager context for vrf [chars][dec] with error [chars] VRF lock manager initialization failure vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LCKMGR_INIT_ERROR 3-Error [chars] VRF lock manager initialization failure vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LCKMGR_INIT_ERROR 3-Error [chars] VRF lock manager initialization failure vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LOCK_ERROR 3-Error Failed to lock VRF [chars]: [chars] Failed to lock a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_LOCK_ERROR 3-Error Failed to lock VRF [chars]: [chars] Failed to lock a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_MT_UPDATE_ERROR 3-Error Failed to update multicast multi-topology mode for address-family [chars] in VRF [chars]: [chars] Failed to update multicast multi-topology mode in a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_MT_UPDATE_ERROR 3-Error Failed to update multicast multi-topology mode for address-family [chars] in VRF [chars]: [chars] Failed to update multicast multi-topology mode in a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_SUBSYSTEM_INIT_FAILED 3-Error VRF subsystem initialization failed: [chars] The VRF subsystem could not be initialized vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_SUBSYSTEM_INIT_FAILED 3-Error VRF subsystem initialization failed: [chars] The VRF subsystem could not be initialized vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_TABLEID_INCONSISTENT 3-Error [chars] VRF tableid inconsistent between two RPs. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_TABLEID_INCONSISTENT 3-Error [chars] VRF tableid inconsistent between two RPs. vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_UNLOCK_ERROR 3-Error Failed to unlock VRF [chars]: [chars] Failed to unlock a VRF vrfinfra LOG_STD_ACTION IP_VRF-3-VRF_UNLOCK_ERROR 3-Error Failed to unlock VRF [chars]: [chars] Failed to unlock a VRF vrfinfra LOG_STD_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_DELAY 4-Warning Unexpected delay while acquiring interface configuration lock Unexpected delay in VRF interface association vrfinfra LOG_STD_NO_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_DELAY 4-Warning Unexpected delay while acquiring interface configuration lock Unexpected delay in VRF interface association vrfinfra LOG_STD_NO_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_IGNORED 4-Warning Ignored interface configuration lock [dec] times Processing is continuing without obtaining the VRF interface configuration lock vrfinfra LOG_STD_NO_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_IGNORED 4-Warning Ignored interface configuration lock [dec] times Processing is continuing without obtaining the VRF interface configuration lock vrfinfra LOG_STD_NO_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_TAKEN 4-Warning Acquired interface configuration lock Unexpected delay in VRF interface association vrfinfra LOG_STD_NO_ACTION IP_VRF-4-VRF_CONFIG_IF_LOCK_TAKEN 4-Warning Acquired interface configuration lock Unexpected delay in VRF interface association vrfinfra LOG_STD_NO_ACTION IP-3-BADIPALIGN 3-Error Invalid alignment in packet for IP. [chars]=[hex] The packet data structure is misaligned. This condition may result in\n\ a small amount of overhead in processing IP traffic. - "Enter a show hardware command and report the output along with this\n\ error message to your technical support representative." IP-3-BADSROUTE 3-Error Improper source route. Length [dec] Ptr [dec] A hardware or software error occurred. - LOG_STD_ACTION IP-3-CNTRFULL 3-Error IP counter block is full setting protocol [dec] An internal software error occured. - LOG_STD_SH_TECH_ACTION IP-3-DESTHOST 3-Error src=[inet] dst=[inet] NULL desthost An internal software error occurred. - LOG_STD_ACTION IP-3-ICMPRATELIMIT 3-Error [dec] unreachables rate-limited within [dec] milliseconds on [chars]. [dec] log messages suppressed since last log message displayed on [chars] An excessive number of packets are triggering log messages on this interface - "change the log threshold with the icmp rate-limit command or " "find the source of the packets and block the packets from this router" IP-3-ICMPRATELIMITDF 3-Error [dec] DF unreachables rate-limited within [dec] milliseconds on [chars]. [dec] DF log messages suppressed since last log message displayed on [chars] An excessive number of packets are triggering log messages on this interface - "change the log threshold with the icmp rate-limit command or " "find the source of the packets and block the packets from this router" IP-3-IPTOPOID 3-Error Topology ID 0x[hec] is invalid can't get the base topology ID. An internal software error occurred - LOG_STD_ACTION IP-3-LOOPOUTIF 3-Error Output interface for packet has been changed for [dec] times and dropped - \nsrc=[inet] dst=[inet] hl=[dec] tl=[dec] prot=[dec] \nin=[chars] nexthop=[inet] out=[chars] A software error occurred. - LOG_STD_ACTION IP-3-LOOPPAK 3-Error Looping packet detected and dropped - \nsrc=[inet] dst=[inet] hl=[dec] tl=[dec] prot=[dec] sport=[dec] dport=[dec] \nin=[chars] nexthop=[inet] out=[chars]\noptions=[chars] A software error occurred. - LOG_STD_ACTION IP-3-MAXIRDP 3-Error Attempt to send IRDP to proxies exceeding configurable limit: [dec] interface: [chars] secondary = [dec] proxy = [dec]\n The sum of configured secondary addresses and configured proxy addresses exceeds the number of total addresses that the IRDP can support in its implementation. - "Reduce the number of either the secondary IP addresses or proxy" " addresses configured for the interface." IP-3-NONALIAS 3-Error non-alias address [inet] in table [chars] found in IP alias list The IP alias list holds IP aliases only but non-alias entries are found. ip LOG_STD_ACTION IP-3-NOOUTINTF 3-Error Output interface not available. source address: [inet] destination address: [inet] routing type: [dec] The output interface for this packet is not set ip LOG_STD_ACTION IP-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. ip LOG_STD_ACTION IP-4-CLASS 4-Warning Bad IP address and mask [inet]%m in class_resolve An internal software error occurred. - LOG_STD_RECUR_ACTION IP-4-DUPADDR 4-Warning Duplicate address [inet] on [chars] sourced by [enet] Another system is using your IP address. - "Change the IP address of one of the two systems." IP-4-IPPOOLS 4-Warning Detected a local pool and a DHCP pool with the same name: [chars] A local pool and a DHCP pool have been configured with the same name. This may cause conflict during address allocations. - "Change the name of one of the two pools" IP-4-UNICASTRPF 4-Warning IP unicast reverse-path check disabled on [chars] The IP verify unicast reverse-path feature was disabled because CEF was disabled either through configuration or due to an internal error. - LOG_STD_SH_TECH_ACTION IP-4-ZERO_ADDR 4-Warning Zero MAC address for [inet] in ARP cache An entry in the ARP cache have a NULL MAC address - "If this message recurs call your technical support\n\ representative for assistance." IP-5-ACL 5-Notice [chars] Error occured in IP access checks. - LOG_STD_SH_TECH_ACTION IP-5-TURBOACL 5-Notice [chars] Error occured in intialisation of TURBOACL. - show process IP-5-WEBINST_COMP 5-Notice Selected IP address [inet] A hardware or software error occurred. - LOG_STD_ACTION IP-5-WEBINST_KILL 5-Notice Terminating DNS process A hardware or software error occurred. - LOG_STD_ACTION IP-5-WEBINST_RESP 5-Notice Sending DNS response to [inet] request was for [inet] - - - IP-5-WEBINST_START 5-Notice Attempting web install from host [inet] A hardware or software error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IP-6-L2MCASTDROP 6-Information Layer 2 Multicast packet detected and dropped src=[inet] dst=[inet] Layer 2 Multicast packet with Layer3 Unicast Destination was dropped. ip LOG_STD_NO_ACTION IP-6-PHYBCASTDROP 6-Information Physical broadcast packet detected and dropped src=[inet] dst=[inet] Physical broadcast packet was dropped. ip LOG_STD_NO_ACTION IPACCESS-2-NOMEMORY 2-Critical Alloc fail for acl-config buffer. Disabling distributed mode on lc Unable to malloc a buffer to send access-list configuration down\n\ to linecards. ip-acl "Enter a show chunks command and report the output along with this\n\ error message to your technical support representative." IPACCESS-2-WRONGREQUEST 2-Critical Invalid request to allocate chunk of size [dec] We only allow acl chunks of max size IPACCESS_LARGE_CHUNK_SZ ip-acl " " IPACCESS-2-WRONGSIZE 2-Critical Incorrect length acl ipc xdr of type=[chars] len=[dec] received Received an acl message of the wrong size for that type ip-acl "Report this error message to your tech support representative." IPACCESS-3-ACL_ACE_LIMIT_EXCEEDED 3-Error Exceeding the max aces[dec] per ACL configurable Error is occurred when aces limit per ACL is exceeding the ACL ace limit set. ip-acl LOG_STD_ACTION IPACCESS-3-ACL_LIMIT_EXCEEDED 3-Error Exceeding max acl limit[dec] configurable failed to create ACL - - - IPACCESS-3-GLOBAL_ACE_LIMIT_EXCEEDED 3-Error Exceeding the global max ace limit configurable[dec] Error is occurred when the global ace limit is exceeded than the global ace limit set. ip-acl LOG_STD_ACTION IPACCESS-3-SANITY_ERROR 3-Error [chars] A sanity error occurred while the ACL was being configured on the RP or while the ACL configuration was being downloaded to the line card. ip-acl LOG_STD_ACTION IPACCESS-3-XDRREGISTRATION 3-Error Failed to register [chars] XDR client due to [chars] Failure to register the said XDR client. ip-acl "Copy the message exactly as it appears and report it to your " "technical support representative." IPACCESS-4-INVALIDACL 4-Warning Invalid ACL field: [chars] is [dec] An internal software error occurred. ip-acl "Copy the message exactly as it appears and report it to your\n\ technical support representative." IPAD-3-BLOCKEMPTY 3-Error Block does not exist. Try to access a block that does not exist. ip "" IPAD-3-CTXTMASKTYPE 3-Error Search context mask type or sub type not recognized: [dec] [dec]. Search\n\ context last found IP address [inet] search context target IP address [inet]. An internal IPAD error occurred. Search contex mask type not defined. ip "" IPAD-3-LISTTYPE 3-Error Double-linked list DLL type not recognized: [dec]. An internal IPAD error occurred. DLL type not defined. ip "" IPAD-3-MEMORY 3-Error Can not allocate memory for a block in IPAD: [chars] The operation may have failed due to lack of memory. ip "" IPAD-3-TRIM 3-Error Access on level [dec] to the left of index [dec]. IPAD is not trimmed properly. ip "" IPC_RSP_CBUS-3-CARDERR 3-Error [chars] An IPC card has registered itself to the IPC master twice. The card malfunctioned and its IPC is not active. - "Copy the error message exactly as it appears and report it to your technical support representative." IPC_RSP_CBUS-3-INVNUM 3-Error [chars] [dec] The IPC application tried to send a message that was larger than IPC could handle. The message was not transmitted. - "Copy the error message exactly as it appears and report it to your technical support representative." IPC_RSP_CBUS-3-MSGERR 3-Error [chars] [dec] System controller Bengal has reported an error/event RSP "Read error reports. SBE are generally not fatal. Most others are" IPC_RSP_CBUS-3-NOBUF 3-Error [chars] The IPC ran out of memory device MEMD buffers. - "Reduce the number of applications currently running on the IPC. Copy the error message exactly as it appears and report it to your technical support representative." IPC_RSP_CBUS-3-NOHWQ 3-Error Hardware queue for card at slot [dec] not found IPC messages cannot be transmitted due to a missing hardware queue. The messages were discarded and subsequent messages will not be transmitted to that card. - "Copy the error message exactly as it appears and report it to your technical support representative." IPC_RSP_CBUS-3-SEATERR 3-Error [chars] [dec] The ID associated with an IPC card is either missing duplicated or cannot be created. - "Copy the error message exactly as it appears and report it to your technical support representative." IPC_TEST-3-INVALID_SUBTYPE 3-Error CPP IPC TEST Proxy subtype [dec] IPC test proxy failed because of receiving invalid sub-type. cpp-ucode LOG_STD_ACTION IPC_TEST-3-MEM_ALLOC_FAILED 3-Error CPP IPC TEST Proxy mem alloc IPC test proxy failed because the GPM allocation failed. cpp-ucode - IPC_TEST-3-REPLY_FAILED 3-Error CPP IPC TEST Proxy send reply IPC test proxy failed because the reply failed to send. cpp-ucode - IPC-2-BADSHARE 2-Critical Bad refcount in [chars] ptr=[hec] count=[dec] A reference count is used to track the usage of IPC messages. A function increments the count when it begins to use a message and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be zero or negative. ipc "show tech-support ipc" IPC-2-BADSHARE 2-Critical Bad refcount in [chars] ptr=[hec] count=[dec] A reference count is used to track the usage of IPC messages. A function increments the count when it begins to use a message and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be zero or negative. ipc "show tech-support ipc" IPC-2-BADSHARE 2-Critical Bad refcount in [chars] ptr=[hec] count=[dec] A reference count is used to track the usage of IPC messages. A function increments the count when it begins to use a message and decrements it when it finishes. When the count becomes zero the data structure is freed. This message indicates that when the count was accessed it was found to be zero or negative. ipc "show tech-support ipc" IPC-2-CANT_SEND 2-Critical [chars]: Cannot send IPC message from 0x[hec] to 0x[hec]: info 0x[hec] An error occurred when sending IPC message ipc "show tech-support ipc" IPC-2-CANT_SEND 2-Critical [chars]: Cannot send IPC message from 0x[hec] to 0x[hec]: info 0x[hec] An error occurred when sending IPC message ipc "show tech-support ipc" IPC-2-CANT_SEND 2-Critical [chars]: Cannot send IPC message from 0x[hec] to 0x[hec]: info 0x[hec] An error occurred when sending IPC message ipc "show tech-support ipc" IPC-2-INITFAILED 2-Critical [chars] IPC Resource Management Initialization failed ipc "This is a critical failure for IPC functionality." "Capture 'sh version' and contact TAC" IPC-2-INITFAILED 2-Critical [chars] IPC Resource Management Initialization failed ipc "This is a critical failure for IPC functionality." "Capture 'sh version' and contact TAC" IPC-2-INITFAILED 2-Critical [chars] IPC Resource Management Initialization failed ipc "This is a critical failure for IPC functionality." "Capture 'sh version' and contact TAC" IPC-2-INVALIDSEAT 2-Critical Invalid IPC Seat 0x[hec]. Some operation is attempted on a seat ID not known to IPC ipc "show tech-support ipc" IPC-2-INVALIDSEAT 2-Critical Invalid IPC Seat 0x[hec]. Some operation is attempted on a seat ID not known to IPC ipc "show tech-support ipc" IPC-2-INVALIDZONE 2-Critical Invalid IPC Zone 0x[hec]. Some operation is attempted on a zone ID not known to IPC ipc "show tech-support ipc" IPC-2-INVALIDZONE 2-Critical Invalid IPC Zone 0x[hec]. Some operation is attempted on a zone ID not known to IPC ipc "show tech-support ipc" IPC-2-INVALIDZONE 2-Critical Invalid IPC Zone 0x[hec]. Some operation is attempted on a zone ID not known to IPC ipc "show tech-support ipc" IPC-2-LOCK 2-Critical Lock done a deleted element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-2-LOCK 2-Critical Lock done a deleted element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-2-LOCK 2-Critical Lock done a deleted element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-2-NO_ACK_HANDLER 2-Critical No handler for ACK with data for port [hec]. The IPC receiver appended data to an ACK. But at the sender there is no corresponding ACK handler. ipc "show tech-support ipc" IPC-2-NO_ACK_HANDLER 2-Critical No handler for ACK with data for port [hec]. The IPC receiver appended data to an ACK. But at the sender there is no corresponding ACK handler. ipc "show tech-support ipc" IPC-2-NO_ACK_HANDLER 2-Critical No handler for ACK with data for port [hec]. The IPC receiver appended data to an ACK. But at the sender there is no corresponding ACK handler. ipc "show tech-support ipc" IPC-2-NOBLOCK 2-Critical Invalid blocking operation in interrupt context or process blocking is disabled: [chars] [hec] Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at interrupt level or when process has disabled blocking ipc show ipc ports IPC-2-NOBLOCK 2-Critical Invalid blocking operation in interrupt context or process blocking is disabled: [chars] [hec] Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at interrupt level or when process has disabled blocking ipc show ipc ports IPC-2-NOBOOL 2-Critical Boolean NULL in IPC message: [hec]. A watched boolean that was allocated while sending the message is found to be NULL when an ACK arrived. ipc show ipc status IPC-2-NOBOOL 2-Critical Boolean NULL in IPC message: [hec]. A watched boolean that was allocated while sending the message is found to be NULL when an ACK arrived. ipc show ipc status IPC-2-NOBOOL 2-Critical Boolean NULL in IPC message: [hec]. A watched boolean that was allocated while sending the message is found to be NULL when an ACK arrived. ipc show ipc status IPC-2-NODISPATCH 2-Critical Message for [hec].[hec] has no receive queue or dispatch routine The IPC user failed to provide any means of handling the received message. ipc show ipc ports IPC-2-NODISPATCH 2-Critical Message for [hec].[hec] has no receive queue or dispatch routine The IPC user failed to provide any means of handling the received message. ipc show ipc ports IPC-2-NODISPATCH 2-Critical Message for [hec].[hec] has no receive queue or dispatch routine The IPC user failed to provide any means of handling the received message. ipc show ipc ports IPC-2-NOMEM 2-Critical No memory available for [chars] The IPC protocol subsystem could not obtain the memory it needed. ipc "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-2-NOMEM 2-Critical No memory available for [chars] The IPC protocol subsystem could not obtain the memory it needed. ipc "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-2-NOMEM 2-Critical No memory available for [chars] The IPC protocol subsystem could not obtain the memory it needed. ipc "If this error message recurs attempt to reduce memory usage by " "reducing the number of router features or interfaces enabled. " "Alternatively add more memory. " "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-2-ONINT 2-Critical Invalid operation at interrupt level: [chars] [hec] Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at the interrupt level. ipc show ipc ports IPC-2-ONINT 2-Critical Invalid operation at interrupt level: [chars] [hec] Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at the interrupt level. ipc show ipc ports IPC-2-ONINT 2-Critical Invalid operation at interrupt level: [chars] [hec] Debug Message. An IPC application has attempted an IPC action which has been prohibited from being performed at the interrupt level. ipc show ipc ports IPC-2-PRECLOSE 2-Critical IPC port pre-closure overflow : 0x[hec] : 0x[hec] An application attempts to close an ipc port when there are messages pending in retransmit queue and ipc defer table overflows. ipc "show ipc ports open" IPC-2-PRECLOSE 2-Critical IPC port pre-closure overflow : 0x[hec] : 0x[hec] An application attempts to close an ipc port when there are messages pending in retransmit queue and ipc defer table overflows. ipc "show ipc ports open" IPC-2-PRECLOSE 2-Critical IPC port pre-closure overflow : 0x[hec] : 0x[hec] An application attempts to close an ipc port when there are messages pending in retransmit queue and ipc defer table overflows. ipc "show ipc ports open" IPC-2-SPI_IOSD_IPC_INIT_FAILED 2-Critical SPI IOSd IPC init failed - [chars]. SPI IOSd IPC initialization failed spi "show tech-support ipc" IPC-2-SPI_IOSD_IPC_INIT_FAILED 2-Critical SPI IOSd IPC init failed - [chars]. SPI IOSd IPC initialization failed spi "show tech-support ipc" IPC-2-TEST 2-Critical IPC test: [chars] The IPC test routines. ipc "IPC test only - no action required." IPC-2-TEST 2-Critical IPC test: [chars] The IPC test routines. ipc "IPC test only - no action required." IPC-2-TEST 2-Critical IPC test: [chars] The IPC test routines. ipc "IPC test only - no action required." IPC-2-UNLOCK 2-Critical Unlock done on already unlocked element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-2-UNLOCK 2-Critical Unlock done on already unlocked element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-2-UNLOCK 2-Critical Unlock done on already unlocked element 0x[hec] An internal inconsistency was found in some IPC data structures. ipc "show tech-support ipc" IPC-3-ACKALLOC 3-Error couldn't send to [chars] Allocating an IPC acknowledgement failed with the likely result that some software on the specified source node will timeout. cpp-ucode LOG_STD_ACTION IPC-3-ACKSEND 3-Error sending to [chars]: [chars] Sending an acknowledgement reply to the specified source failed for the given reason with the likely result that some software on the source will timeout. cpp-ucode LOG_STD_ACTION IPC-3-APP_IPC_FAIL 3-Error [chars] failed. IPC Error: [chars] [dec] IPC Application Process failed to do some operation with the IPC Layer. The message includes the error code from ipc layer ipc show ipc status IPC-3-APP_IPC_FAIL 3-Error [chars] failed. IPC Error: [chars] [dec] IPC Application Process failed to do some operation with the IPC Layer. The message includes the error code from ipc layer ipc show ipc status IPC-3-APP_IPC_FAIL 3-Error [chars] failed. IPC Error: [chars] [dec] IPC Application Process failed to do some operation with the IPC Layer. The message includes the error code from ipc layer ipc show ipc status IPC-3-BADLENGTH 3-Error IPC length [dec] > received length [dec] to sub device [dec] with fc code [dec] The length field in an IPC packet was larger than the number of bytes actually in the packet. cpp-ucode LOG_STD_ACTION IPC-3-BADMSG 3-Error received type [dec] An IPC message was received containing an invalid message type. cpp-ucode LOG_STD_ACTION IPC-3-BADRSTATE 3-Error Received ICP msg state [dec] Received IPC message while connection not ACTIVE cpp-ucode LOG_STD_ACTION IPC-3-BADSEQ 3-Error got [dec] expected [dec] from [chars] - - - IPC-3-CNTALLOC 3-Error IPC control msg subtype [dec] Allocating an IPC control message failed. cpp-ucode LOG_STD_ACTION IPC-3-CNTSEND 3-Error sending ICP msg subtype [dec] to [chars]: [chars] Sending an ICP control message to the specified source failed for the given reason. Message should will be retried cpp-ucode LOG_STD_ACTION IPC-3-CONTROL 3-Error Unhandled message subtype [dec] An IPC control message was received containing an unrecognized type. cpp-ucode LOG_STD_ACTION IPC-3-CREATEFAIL 3-Error IPC CREATE msg failed invalid [chars] [dec] IPC Create message had invalid parameter cpp-ucode LOG_STD_ACTION IPC-3-DELETED 3-Error Attempt to delete an IPC message 0x[hec] a second time - - - IPC-3-DELETED 3-Error Attempt to delete an IPC message 0x[hec] a second time - - - IPC-3-DELETED 3-Error Attempt to delete an IPC message 0x[hec] a second time - - - IPC-3-GIANT 3-Error Request for giant IPC packet denied. Request size = [dec] Someone requested a message that was too large for the IPC system ipc "show tech-support ipc" IPC-3-GIANT 3-Error Request for giant IPC packet denied. Request size = [dec] Someone requested a message that was too large for the IPC system ipc "show tech-support ipc" IPC-3-GIANT 3-Error Request for giant IPC packet denied. Request size = [dec] Someone requested a message that was too large for the IPC system ipc "show tech-support ipc" IPC-3-INIT_IN_PROGRESS 3-Error IPC Message received before init complete Cannot process IPC packet until init stage is complete - LOG_STD_ACTION IPC-3-ISSU_API_ERR 3-Error [chars] failed with error code [dec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu client IPC-3-ISSU_API_ERR 3-Error [chars] failed with error code [dec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu client IPC-3-ISSU_API_ERR 3-Error [chars] failed with error code [dec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu client IPC-3-ISSU_ERROR 3-Error [chars] failed with error code [dec] for seat [hec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu fsm IPC-3-ISSU_ERROR 3-Error [chars] failed with error code [dec] for seat [hec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu fsm IPC-3-ISSU_ERROR 3-Error [chars] failed with error code [dec] for seat [hec] ISSU API failed to do some operation for IPC layer The message includes the error code from ISSU library os-ipc show issu fsm IPC-3-LOG_ERR 3-Error [chars] CPP QoS Client Proxy failure QoS proxy failed because of receiving invalid sub-type or failed to allocate ipc response buffer. cpp-ucode LOG_STD_ACTION IPC-3-LOWBUFF 3-Error The main IPC message header cache below application reserve count [dec]. - - - IPC-3-LOWBUFF 3-Error The main IPC message header cache below application reserve count [dec]. - - - IPC-3-LOWBUFF 3-Error The main IPC message header cache below application reserve count [dec]. - - - IPC-3-NOBUFF 3-Error The [chars] IPC message header cache is empty The specified IPC message header cache is empty and an incoming IPC message may be dropped as a result. ipc "show tech-support ipc" IPC-3-NOBUFF 3-Error The [chars] IPC message header cache is empty The specified IPC message header cache is empty and an incoming IPC message may be dropped as a result. ipc "show tech-support ipc" IPC-3-NOBUFF 3-Error The [chars] IPC message header cache is empty The specified IPC message header cache is empty and an incoming IPC message may be dropped as a result. ipc "show tech-support ipc" IPC-3-NOHANDLER 3-Error message type [dec] from [chars] An IPC message was received containing an unrecognized type. cpp-ucode LOG_STD_ACTION IPC-3-NOSRC 3-Error packet from id [dec] Received an IPC packet from an unrecognized source node with the specified ID. cpp-ucode LOG_STD_ACTION IPC-3-NULL_SESSION 3-Error unable to process ipc mcast message - no member session for dest_port_info %p group 0x[hec] session [dec] For appclass [chars] IPC Mcast message has been received for a NULL session ipc show ipc mcast session verbose IPC-3-NULL_SESSION 3-Error unable to process ipc mcast message - no member session for dest_port_info %p group 0x[hec] session [dec] For appclass [chars] IPC Mcast message has been received for a NULL session ipc show ipc mcast session verbose IPC-3-PGENALLOC 3-Error [dec] bytes Allocating a packet of the specified size failed. cpp-ucode LOG_STD_ACTION IPC-3-PGENSEND 3-Error [chars] Sending a generated packet failed for the specified reason. cpp-ucode LOG_STD_ACTION IPC-3-PROXY_IPC_ALLOC_FAILED 3-Error Allocate IPC message by [chars] failed - [chars] Allocation of an IPC packet buffer by proxy failed. cpp-ucode LOG_STD_ACTION IPC-3-PROXY_IPC_SEND_FAILED 3-Error Attempt to send IPC message by [chars] failed with [chars] Transmission of an IPC message by proxy failed. cpp-ucode LOG_STD_ACTION IPC-3-REPLY 3-Error unexpected from [chars] An unexpected reply was received from the specified source. cpp-ucode LOG_STD_ACTION IPC-3-TOOBIG 3-Error message type [dec] length [dec] offset [hec] from [chars] The length field in an IPC message was found to extend beyond the packet that contained it. cpp-ucode LOG_STD_ACTION IPC-3-TOOSMALL 3-Error message type [dec] length [dec] offset [hec] from [chars] The length field in an IPC message was smaller than the IPC msg header length. cpp-ucode LOG_STD_ACTION IPC-4-CONSISTENCY 4-Warning Consistency check failed for [chars] 0x[hec] Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show tech-support ipc" IPC-4-CONSISTENCY 4-Warning Consistency check failed for [chars] 0x[hec] Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show tech-support ipc" IPC-4-CONSISTENCY 4-Warning Consistency check failed for [chars] 0x[hec] Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show tech-support ipc" IPC-4-GET_PAK_MSG 4-Warning Failed for message size [dec] System unable to allocate IPC message of required size. ipc "If this error message recurs copy the error message exactly" " as it appears on the console or in the system log contact" " your Cisco technical support representative with the" " gathered information." "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-4-GET_PAK_MSG 4-Warning Failed for message size [dec] System unable to allocate IPC message of required size. ipc "If this error message recurs copy the error message exactly" " as it appears on the console or in the system log contact" " your Cisco technical support representative with the" " gathered information." "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-4-GET_PAK_MSG 4-Warning Failed for message size [dec] System unable to allocate IPC message of required size. ipc "If this error message recurs copy the error message exactly" " as it appears on the console or in the system log contact" " your Cisco technical support representative with the" " gathered information." "\n\nTo display total memory usage for a router enter " "show memory summary at the privileged " "command line prompt. To display buffer usage enter " "show buffers at the prompt. To display IPC " "usage enter show ipc queue at the prompt" IPC-4-MESSAGE_ERR 4-Warning Consistency check failed for IPC Message. IPC message 0x[hec] and port information 0x[hec] differ Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show ipc ports" IPC-4-MESSAGE_ERR 4-Warning Consistency check failed for IPC Message. IPC message 0x[hec] and port information 0x[hec] differ Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show ipc ports" IPC-4-MESSAGE_ERR 4-Warning Consistency check failed for IPC Message. IPC message 0x[hec] and port information 0x[hec] differ Debug Message. An action attempted by the IPC module has encountered an unexpected state in its/clients data structures. ipc "show ipc ports" IPC-4-NOPORT 4-Warning Port Not Found. [hec] --> [hec] Index:[hec] Seq: [dec] flags: [hec] size: [dec] IPC Received a message which is destined for a port that cannot be found by IPC ipc "Capture 'sh ipc status' 'sh ipc ports' and" " 'deb ipc errors' outputs and contact TAC" IPC-4-NOPORT 4-Warning Port Not Found. [hec] --> [hec] Index:[hec] Seq: [dec] flags: [hec] size: [dec] IPC Received a message which is destined for a port that cannot be found by IPC ipc "Capture 'sh ipc status' 'sh ipc ports' and" " 'deb ipc errors' outputs and contact TAC" IPC-4-NOPORT 4-Warning Port Not Found. [hec] --> [hec] Index:[hec] Seq: [dec] flags: [hec] size: [dec] IPC Received a message which is destined for a port that cannot be found by IPC ipc "Capture 'sh ipc status' 'sh ipc ports' and" " 'deb ipc errors' outputs and contact TAC" IPC-5-FC_OFF 5-Notice SEAT FC is turned off for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last AckXmitted [dec] SEAT FC is being turned off ipc "show tech-support ipc" IPC-5-FC_OFF 5-Notice SEAT FC is turned off for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last AckXmitted [dec] SEAT FC is being turned off ipc "show tech-support ipc" IPC-5-FC_ON 5-Notice SEAT FC is turned on for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last Ack xmitted [dec] SEAT FC is being turned on Wait for it to be turned off . ipc "show tech-support ipc" IPC-5-FC_ON 5-Notice SEAT FC is turned on for Seat [hec] Port ID [hec] Port Index [dec] Portinfo [hec] Last sent [dec] Last Heard [dec] Last xmitted [dec] Last Ack [dec] Ack Pending [dec] Last Ack xmitted [dec] SEAT FC is being turned on Wait for it to be turned off . ipc "show tech-support ipc" IPC-5-INVALID 5-Notice [chars] Dest Port 0x[hec] Session 0x[hec] Source 0x[hec] While processing an incoming message IPC encountered invalid data in its internal data structures. ipc "show tech-support ipc" IPC-5-INVALID 5-Notice [chars] Dest Port 0x[hec] Session 0x[hec] Source 0x[hec] While processing an incoming message IPC encountered invalid data in its internal data structures. ipc "show tech-support ipc" IPC-5-INVALID 5-Notice [chars] Dest Port 0x[hec] Session 0x[hec] Source 0x[hec] While processing an incoming message IPC encountered invalid data in its internal data structures. ipc "show tech-support ipc" IPC-5-INVALIDINPUT 5-Notice [chars] IPC API is called with invalid argument. os-ipc LOG_STD_RECUR_ACTION IPC-5-INVALIDINPUT 5-Notice [chars] IPC API is called with invalid argument. os-ipc LOG_STD_RECUR_ACTION IPC-5-INVALIDINPUT 5-Notice [chars] IPC API is called with invalid argument. os-ipc LOG_STD_RECUR_ACTION IPC-5-MSG_NULL 5-Notice [chars] IPC message returned is Null ipc "show tech-support ipc" IPC-5-MSG_NULL 5-Notice [chars] IPC message returned is Null ipc "show tech-support ipc" IPC-5-MSG_NULL 5-Notice [chars] IPC message returned is Null ipc "show tech-support ipc" IPC-5-NOCALLBACK 5-Notice [chars]: Flow control callback function is not provided by IPC Client [chars] An IPC application cannot be controlled if flow need to be slowed down. This might result in drop of IPC packets ipc "show ipc ports" IPC-5-NOCALLBACK 5-Notice [chars]: Flow control callback function is not provided by IPC Client [chars] An IPC application cannot be controlled if flow need to be slowed down. This might result in drop of IPC packets ipc "show ipc ports" IPC-5-NOCALLBACK 5-Notice [chars]: Flow control callback function is not provided by IPC Client [chars] An IPC application cannot be controlled if flow need to be slowed down. This might result in drop of IPC packets ipc "show ipc ports" IPC-5-NODELFUNC 5-Notice Failed to intialize IPC client An IPC application cannot be initialized because its initialization\n function does not appear in the IPC initialization list. ipc "show tech-support ipc" IPC-5-NODELFUNC 5-Notice Failed to intialize IPC client An IPC application cannot be initialized because its initialization\n function does not appear in the IPC initialization list. ipc "show tech-support ipc" IPC-5-NODELFUNC 5-Notice Failed to intialize IPC client An IPC application cannot be initialized because its initialization\n function does not appear in the IPC initialization list. ipc "show tech-support ipc" IPC-5-NULL 5-Notice [chars] [chars]=0x[hec] [chars] 0x[hec] IPC module could not find an IPC entity that is expected to be existing always ipc "show tech-support ipc" IPC-5-NULL 5-Notice [chars] [chars]=0x[hec] [chars] 0x[hec] IPC module could not find an IPC entity that is expected to be existing always ipc "show tech-support ipc" IPC-5-NULL 5-Notice [chars] [chars]=0x[hec] [chars] 0x[hec] IPC module could not find an IPC entity that is expected to be existing always ipc "show tech-support ipc" IPC-5-NULL_HEADER 5-Notice [chars] MSG: ptr: %p flags: 0x[hec] IPC message header accessed from IPC message is NULL ipc "show tech-support ipc" IPC-5-NULL_HEADER 5-Notice [chars] MSG: ptr: %p flags: 0x[hec] IPC message header accessed from IPC message is NULL ipc "show tech-support ipc" IPC-5-NULLBPHANDLER 5-Notice Passed Null backpressure handler The maximum message timeout for an IPC message exceeds 2 minutes ipc "Capture 'sh version' and contact TAC" IPC-5-NULLBPHANDLER 5-Notice Passed Null backpressure handler The maximum message timeout for an IPC message exceeds 2 minutes ipc "Capture 'sh version' and contact TAC" IPC-5-NULLBPHANDLER 5-Notice Passed Null backpressure handler The maximum message timeout for an IPC message exceeds 2 minutes ipc "Capture 'sh version' and contact TAC" IPC-5-NULLDELFUNC 5-Notice Invalid registration An IPC application has attempted to register NULL function in the IPC initialization list. ipc "show tech-support ipc" IPC-5-NULLDELFUNC 5-Notice Invalid registration An IPC application has attempted to register NULL function in the IPC initialization list. ipc "show tech-support ipc" IPC-5-NULLDELFUNC 5-Notice Invalid registration An IPC application has attempted to register NULL function in the IPC initialization list. ipc "show tech-support ipc" IPC-5-QFULL 5-Notice Q=0x[hec] [chars] [dec] IPC queue is full. os-ipc LOG_STD_SH_TECH_ACTION IPC-5-QFULL 5-Notice Q=0x[hec] [chars] [dec] IPC queue is full. os-ipc LOG_STD_SH_TECH_ACTION IPC-5-QFULL 5-Notice Q=0x[hec] [chars] [dec] IPC queue is full. os-ipc LOG_STD_SH_TECH_ACTION IPC-5-REGPORTFAIL 5-Notice [chars] [chars]=0x[hec] [chars]=0x[hec] Several IPC messages are pending to be processed. If the number increases it may result in the IPC header cache or buffers being exhausted. ipc "show tech-support ipc" IPC-5-REGPORTFAIL 5-Notice [chars] [chars]=0x[hec] [chars]=0x[hec] Several IPC messages are pending to be processed. If the number increases it may result in the IPC header cache or buffers being exhausted. ipc "show tech-support ipc" IPC-5-REGPORTFAIL 5-Notice [chars] [chars]=0x[hec] [chars]=0x[hec] IPC failed to register the control port ipc LOG_STD_RECUR_ACTION IPC-5-RPCFULL 5-Notice Cannot hold RPC message port: [hex] index: [dec] type: [hex] An RPC request for an application could not be added to the RPC request table because pending requests have filled the RPC request table. ipc "show tech-support ipc" IPC-5-RPCFULL 5-Notice Cannot hold RPC message port: [hex] index: [dec] type: [hex] An RPC request for an application could not be added to the RPC request table because pending requests have filled the RPC request table. ipc "show tech-support ipc" IPC-5-RPCFULL 5-Notice Cannot hold RPC message port: [hex] index: [dec] type: [hex] An RPC request for an application could not be added to the RPC request table because pending requests have filled the RPC request table. ipc "show tech-support ipc" IPC-5-SEND_APP_MSG_FAILED 5-Notice Send message to peer for [chars] failed. Reason: [chars] Client using IPC App Port has not been able to send message ipc "If the reason is 'no such port' then this may be caused because" " of the difference in the versions of IOS running on Active" " and the standby. Any other reason please collect 'sh ipc stat'" " 'sh ipc rpc' 'sh ipc port' on active and standby RPs and " " contact tac" IPC-5-SEND_APP_MSG_FAILED 5-Notice Send message to peer for [chars] failed. Reason: [chars] Client using IPC App Port has not been able to send message ipc "If the reason is 'no such port' then this may be caused because" " of the difference in the versions of IOS running on Active" " and the standby. Any other reason please collect 'sh ipc stat'" " 'sh ipc rpc' 'sh ipc port' on active and standby RPs and " " contact tac" IPC-5-SEND_APP_MSG_FAILED 5-Notice Send message to peer for [chars] failed. Reason: [chars] Client using IPC App Port has not been able to send message ipc "If the reason is 'no such port' then this may be caused because" " of the difference in the versions of IOS running on Active" " and the standby. Any other reason please collect 'sh ipc stat'" " 'sh ipc rpc' 'sh ipc port' on active and standby RPs and " " contact tac" IPC-5-SLAVELOG 5-Notice VIP-[chars] The Cisco IOS software running on a Versatile Interface Processor VIP card generated this message. The error message has been high-vip "This is actually a Cisco IOS error message from a VIP. Handle " "it as indicated by the text after the 'VIP-' string in the " "error message." IPC-5-SLAVELOG 5-Notice VIP-[chars] The Cisco IOS software running on a Versatile Interface Processor VIP card generated this message. The error message has been high-vip "This is actually a Cisco IOS error message from a VIP. Handle " "it as indicated by the text after the 'VIP-' string in the " "error message." IPC-5-SLAVELOG 5-Notice VIP-[chars] The Cisco IOS software running on a Versatile Interface Processor VIP card generated this message. The error message has been high-vip "This is actually a Cisco IOS error message from a VIP. Handle " "it as indicated by the text after the 'VIP-' string in the " "error message." IPC-5-WATERMARK 5-Notice [dec] messages pending in [chars] for the port [chars][hec].[hec] from source seat [hec] - - - IPC-6-ACKRETRY 6-Information required [dec] retries Allocating an IPC acknowledgement failed on the first attempt but succeeded on a later attempt. cpp-ucode LOG_STD_ACTION IPC-6-KEEPALIVE 6-Information Rcvd keepalive from seat 0x[hec] msglen=[dec] An IPC Keepalive message sent for every 10 sec ipc "This is normal behavior" IPC-6-KEEPALIVE 6-Information Rcvd keepalive from seat 0x[hec] msglen=[dec] An IPC Keepalive message sent for every 10 sec ipc "This is normal behavior" IPC-6-MAXRPCTIMEOUT 6-Information Maximum RPC timeout value [dec] seconds set for port 0x[hec] The maximum RPC timeout for an IPC message exceeds the maximum expected value of 10 minutes ipc "Capture 'show techsupport ipc' and contact TAC" IPC-6-MAXRPCTIMEOUT 6-Information Maximum RPC timeout value [dec] seconds set for port 0x[hec] The maximum RPC timeout for an IPC message exceeds the maximum expected value of 10 minutes ipc "Capture 'show techsupport ipc' and contact TAC" IPC-6-MAXRPCTIMEOUT 6-Information Maximum RPC timeout value [dec] seconds set for port 0x[hec] The maximum RPC timeout for an IPC message exceeds the maximum expected value of 10 minutes. If you are using MOS IPC it may report some fake RPC timeouts at the receiver ipc "Capture 'show techsupport ipc' and contact TAC" IPC-6-STATEFUL 6-Information [chars] A Stateful IPC Event occurred ipc "This is not a bug but just an informational message." IPC-6-STATEFUL 6-Information [chars] A Stateful IPC Event occurred ipc "This is not a bug but just an informational message." IPC-6-STATEFUL 6-Information [chars] A Stateful IPC Event occurred ipc "" IPC-7-RECYCLE_HEADER_ALLOC_FAIL 7-Debug Unable to alloc gpm for recycle header An IPC message need memory to build recycle header. cpp-ucode LOG_STD_ACTION IPC-7-RECYCLE_TAIL_DROP 7-Debug Dropping IPC packet due to recycle queue full An IPC message can't recycled due to queue full. cpp-ucode LOG_STD_ACTION IPCGRP-3-CARDERR 3-Error [chars] An IPC card has registered itself to the IPC master twice. The card malfunctioned and its IPC is not active. ubr7200-sw LOG_STD_ACTION IPCGRP-3-CMDOP 3-Error IPC command [dec] slot[dec]/[dec]: [chars] IPC command processing operational errors. ubr7200-sw LOG_STD_ACTION IPCGRP-3-CREATE_FAIL 3-Error [chars] [chars] Failed to create IPC port on RP. ubr7200-sw LOG_STD_ACTION IPCGRP-3-ENQFAIL 3-Error enqueue failed! queue:[chars] size:[dec] process_enqueue failed. ubr7200-sw LOG_STD_ACTION IPCGRP-3-ERROR 3-Error [chars]: [chars] An IPC error was detected ubr7200-sw "Copy the error message exactly as it appears and report it to your " "technical support representative." IPCGRP-3-EVENTOP 3-Error Event [dec] from slot[dec]/[dec]: [chars] IPC event processing operational errors. ubr7200-sw LOG_STD_ACTION IPCGRP-3-EXECCMDMSG 3-Error Incorrect msg size size=[dec] Wrong size of a REXEC-On IPC command. ubr7200-sw LOG_STD_ACTION IPCGRP-3-INVALID_PARAMS 3-Error Invalid interface[dec]/[dec]/[dec] Invalid interface addressed by the corresponding IPC message. ubr7200-sw LOG_STD_ACTION IPCGRP-3-INVNUM 3-Error [chars] [dec] - - - IPCGRP-3-LOADQUACKFAIL 3-Error slot [dec] load quack data failed! load quack data failed. ubr7200-sw LOG_STD_ACTION IPCGRP-3-MSGERR 3-Error [chars] [dec] The slave IPC cannot register with master. It cannot exchange messages with the master. ubr7200-sw LOG_STD_ACTION IPCGRP-3-NBLKCMD 3-Error [chars] Nonblocking IPC command queue initialization failure. ubr7200-sw LOG_STD_ACTION IPCGRP-3-NOHWIDB 3-Error Cannot find hwidb for interface[dec]/[dec] Interface identifier does not exist for the interface addressed by the corresponding IPC message. ubr7200-sw LOG_STD_ACTION IPCGRP-3-NULLMSG 3-Error Null [chars] ipc message An empty IPC message which is not expected to be received. ubr7200-sw LOG_STD_ACTION IPCGRP-3-NULLREXECCMD 3-Error Received empty ipc rexec cmd message REXEC-On IPC command failure. ubr7200-sw LOG_STD_ACTION IPCGRP-3-REXEC 3-Error [chars] REXEC-On IPC command failure. ubr7200-sw LOG_STD_ACTION IPCGRP-3-SEATERR 3-Error [chars] [dec] The ID associated with an IPC card is either missing duplicated or cannot be created. ubr7200-sw LOG_STD_ACTION IPCGRP-3-SYSCALL 3-Error System call for command [dec] slot[dec]/[dec] : [chars] Cause: [chars] - - - IPCGRP-6-NBLKCMD_Q_FULL 6-Information Nonblocking IPC command queue full [dec] commands - - - IPCOIR-2-CARD_UP_DOWN 2-Critical Card in slot [dec]/[dec] is [chars]. Notifying [chars] driver. Notification of a Line Card coming Up or Down. ubr7200-sw LOG_STD_NO_ACTION IPCOIR-2-CREATEFAIL 2-Critical Couldn't create [chars] Could not create specified resource ubr7200-sw "Contact customer support." IPCOIR-2-NULL_PTR 2-Critical [chars]: pointer is null Unexpected NULL pointer to a data structure. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-2-PLUGIN_PREANALYZE_FAIL 2-Critical Unable to preanalyze driver plugin in slot [dec]/[dec]. A valid linecard driver preanalyze failed. ubr7200-sw "Possibly incompatible card types" IPCOIR-3-BADIPHOST 3-Error Bad IP address or host name [chars] The IP address or host name is incorrect or unknown. ubr7200-sw "Check the IP address or hostname." IPCOIR-3-BADLCAPI 3-Error Incorrect API message version 0x[hec] The linecard and IOS images are badly out of phase. ubr7200-sw "Contact customer support." IPCOIR-3-BADMESSVER 3-Error Incorrect message version obj 0x[hec] op 0x[hec] version 0x[hec] The linecard and IOS images are badly out of phase. ubr7200-sw "Contact customer support." IPCOIR-3-BOGUSCARD 3-Error Bogus cardtype [dec] The indicated cardtype is unknown to the software. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-CARD_BADIDPROM 3-Error Card in slot [dec]/[dec] has an invalid card type in IDPROM The linecard IDPROM is unprogrammed or has failed. ubr7200-sw "Contact customer support." IPCOIR-3-CARD_GET_VERSION_RESPONSE 3-Error Unsolicited response from slot [dec]/[dec] oir_state = [chars] Unexpected message from a Line Card. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-CARD_UNSUPPORTED 3-Error Unsupported card type 0x[hec] in slot [dec]/[dec]. The linecard is not supported by this version of IOS ubr7200-sw "Contact customer support." IPCOIR-3-CARDCRASH 3-Error Card crashed in slot [dec]/[dec]. IPC message reporting wrong version received from an operational card. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-CRE_INIT_FAIL 3-Error Unable to initialize PRE ports. The PRE plugin init sequence failed. ubr7200-sw "Determine and fix cause." IPCOIR-3-FLASHFAIL 3-Error Couldn't load [chars]...\n The indicated image is inaccessible ubr7200-sw "Check the filename." IPCOIR-3-IMAGEVERSION 3-Error Image version stamp missing The loaded image did not contain a recognizable version stamp ubr7200-sw "Replace the image with known-good bits and try again." IPCOIR-3-IPC_GET_MSG_BUF_FAIL 3-Error Unable to get an IPC msg buffer in [dec] tries: slot [dec]/[dec] The IOS IPC buffer pool was empty for a sustained period of time. ubr7200-sw "Install more processor SDRAM in the PRE." IPCOIR-3-KEEPALIVE 3-Error A keepalive timeout occurred on slot [dec]/[dec].\n Last process: [chars] 4ms time = [dec]ms Intr. Busy Count: [dec] Sched Flag Count: [dec] The line card has stopped responding to keepalive polls while in the RUN state. The attached debug information was provided by the line card. ubr7200-sw "Monitor the LC for a persistent problem. Keep the console log of " "each occurrence and if the problem occurs again forward the log to " "Cisco." IPCOIR-3-LC4MS 3-Error The watchdog timer on slot [dec]/0 has stopped. The line card has stopped servicing it's watchdog timer. ubr7200-sw "The condition may be temporary or may be caused by a crash. " "Check the LC's bootflash for crashinfo files and monitor " "the LC for a watchdog timeout." IPCOIR-3-LCCRASH 3-Error The card in slot [dec]/[dec] has crashed. Cause Register: 0x%0x Signal: %0u The line card in the specified slot has crashed. ubr7200-sw "Wait for the LC to come back up then connect to the remote console and " "extract the crashinfo file from bootflash. Forward the file the " "output from a show tech command and the NPE console log to Cisco." IPCOIR-3-LOADER_DNLD_NOBUF 3-Error Buffer allocation failed The buffer downloader couldn't allocate a message buffer. ubr7200-sw "Reboot the chassis." IPCOIR-3-LOADER_DNLD_REJECT 3-Error Buffer download to slot [dec]/[dec] rejected The linecard buffer download server rejected the download. ubr7200-sw LOG_STD_ACTION IPCOIR-3-LOADER_IPC_FAIL 3-Error IPC failed [chars] [chars] slot [dec]/[dec] The IOS IPC protocol reported an unexpected error. ubr7200-sw "Make sure the indicated card is still plugged in." IPCOIR-3-LOADER_SERVER_FAIL 3-Error Remote server refused to load slot [dec]/[dec] Unable to load a Line Card. Load will be attempted again. ubr7200-sw LOG_STD_ACTION IPCOIR-3-PLUGIN_INIT_FAIL 3-Error Unable to create driver plugin in slot [dec]/[dec]. A valid linecard driver plugin create failed. ubr7200-sw "Perhaps a memory allocation failure should not happen." IPCOIR-3-STATE_MACHINE_BUG 3-Error card_oir_loading called should never happen recovering. An internal software error occurred. Will recover. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-STATE_MACHINE_BUG2 3-Error card_oir_insert_card: already have 0x[hec] removing. An internal software error occurred. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-TFTPFAIL 3-Error TFTP of [chars] from [chars] failed...\n The indicated image is inaccessible ubr7200-sw "Check file permissions network connectivity." IPCOIR-3-TIMEOUT 3-Error Timeout waiting for a response from slot [dec]/[dec]. NPE lost connection with a Line Card. Line Card might have crashed. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-3-WRONGCARDTYPE 3-Error Wrong card type in slot [dec]/[dec]. IPC message reporting wrong card type received from an operational card. ubr7200-sw LOG_STD_SH_TECH_ACTION IPCOIR-4-IPC_GET_MSG_BUF 4-Warning Get IPC msg buf failed [dec] times: slot [dec]/[dec] - retry in [dec] sec The IOS IPC buffer pool was temporarily empty. ubr7200-sw "Consider installing more processor SDRAM in the PRE." IPCOIR-4-REPEATMSG 4-Warning IPC handle already exists for [dec]/[dec] IPC communication between the NPE and a Line Card already setup ubr7200-sw "Reload the specified linecard. If the message recurs call your " "techical support representative for assistance." IPCOIR-5-CARD_DETECTED 5-Notice Card type [chars] 0x[hec] in slot [dec]/[dec] A card was detected in the indicated slot. ubr7200-sw LOG_STD_NO_ACTION IPCOIR-5-CARD_LOADING 5-Notice Loading card in slot [dec]/[dec] Notification of a Line Card download with MD5 data. ubr7200-sw LOG_STD_NO_ACTION IPCOIR-6-LCWAITINFO 6-Information CLC [dec]/[dec]> [chars] The NPE OIR handler received a console error message from a distributed line card while in the crashwait state. The handler enters this state when it detects a Keepalive timeout on a distributed line card. During the crash wait period the LC is expected to collect and store crash information. At the end of the wait period the NPE will reload the LC. During this time it's possible that the LC will try to send error messages to it's console. Normally these would be sent to the NPE via the logger. However during the wait period the IPC link between the NPE and the LC is down so the OIR debug code provides a rudimentary method of collecting and displaying these messages ubr7200-sw "Report the problem to Cisco. Include the log messages along with the " "output of the show tech command and crashinfo file from the LC." IPDR-2-ERROR_SOCKET 2-Critical \n Receive a wrong socket id [dec] The socket to close is not exist or belong to the ipdr process cmts-application LOG_STD_SH_TECH_ACTION IPDR-2-GENERAL_ERR_SOCKET 2-Critical \n [chars] encounter some error when binding listening or receiving the event from the socket fd cmts-application LOG_STD_SH_TECH_ACTION IPE-2-HOST_SECURITY_VIOLATION 2-Critical Security violation occurred caused by IP address [inet] on port [chars]. An unauthorized device attempted to connect on a secure port. The IP address of the unauthorized device and the secure port are specified in the error message. ipe "Determine the device that attempted to connect on the secure port." "Notify your network system administrator of this condition." IPE-3-DUPLICATE_CONFIG_MASTER 3-Error Multiple Configuration Masters in domain [chars]. Use \show ipe errors\ command to check for errors. There must be one Configuration Masters in every IPe domain. ipe "Make sure that there is only one Forwarder configured as the " "Configuration Master in a domain. Use \"show ipe errors\" " "command to identify the forwarders and fix the error condition" IPE-3-PG_ACL_RESOURCE 3-Error Failed to allocate an internal ACL resource needed for Policy Gateway An attempt to allocate an internal ACL failed. ipe LOG_STD_ACTION IPE-3-PG_VLAN_RESOURCE 3-Error Failed to allocate an internal vlan resource needed for Policy Gateway An attempt to allocate an internal vlan failed. ipe "Please check the config and make sure that vlan resources " "are available" IPE-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. ipe LOG_STD_ACTION IPE-3-STATICHOST 3-Error Failed to add [chars] entry for host [inet] of tableid [dec] An internal software error occurred. ipe LOG_STD_ACTION IPE-4-DUPLICATE_HOST 4-Warning Host [inet] is attached to multiple forwarders. Use \show ipe errors\ command to check for possible errors. In a host move scenario it is possible that a host is transiently attached to multiple forwarders during IPe convergence. However it is an error if a host continues to be attached to multiple forwarders. ipe "Use \"show ipe errors\" command to identify the forwarders where " "the host is reported to be attached and fix the error condition." IPE-4-DUPLICATE_LOCAL_HOST 4-Warning Host [inet] on interface [chars] has duplicate ip address. If existing host has been removed it is possible that this is a transient condition. An expedited ARP track is started on existing host to remove the entry if the host is no longer there. Once existing entry is removed host addition will be possible. However it is an error if multiple hosts continue to use duplicate address. ipe "Use \"show ip host mapping\" command to identify the interface where " "the host is reported to be attached and remove the duplicate ip " "address from one of the hosts." IPFAST-2-FAILOPENIPCPORT 2-Critical Could not open the IPC ports. [chars] ipfast could not open the ipc port to communicate to the LC/RRP/SP. - LOG_STD_SH_TECH_ACTION IPFAST-2-INVALSIZE 2-Critical The IP fast path received an IPC message with an invalid sizesize/type - [dec]/[dec] - - - IPFAST-2-IPCACHEINIT 2-Critical Error initializing IP fast cache structures A programming error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IPFAST-2-MSGDROP 2-Critical IPC queue limit is reached and message is dropped. queue limit = [dec] cumulative drops = [dec] IPC raw queue limit for IP fast path is reached. - LOG_STD_ACTION IPFAST-2-RADIXINIT 2-Critical Error initializing IP fast cache structures A programming error occurred. - LOG_STD_SH_TECH_ACTION IPFAST-6-PAKSHORT 6-Information Packet too short from [inet] datagram size [dec] tl [dec] An IP packet which is too short was received - LOG_STD_NO_ACTION IPFLOW-2-CACHEINIT 2-Critical Error initializing IP flow cache Initialization of the Flow cache could not be accomplished because of \n\ a low memory condition. netflow-switch LOG_STD_SH_TECH_ACTION IPFLOW-2-EXPORTINIT 2-Critical Error initializing Flow Export queue Initialization of the Flow export queue could not be accomplished \n\ because of a low memory condition. netflow-switch "Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." IPFLOW-2-PROCESSINIT 2-Critical Error initializing Flow background process Initialization of the Flow background process could not be accomplished because of a low memory condition. netflow-switch "Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." IPFLOW-2-QUEUEINIT 2-Critical Error initializing Flow feature queue Initialization of the Flow feature queue could not be accomplished because of a low memory condition. netflow-switch "Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." IPFLOW-2-TEMPLATETBL_INIT 2-Critical Error initializing Flow Export Template Table Initialization of the Flow export template table could not be \n\ accomplished because of a low memory condition. netflow-switch "Reduce other system activitiy to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." IPFLOW-3-DISABLEFLOWEXPORT 3-Error NULL Flow export is disabled because export destination address matches with one of the interface's IP addresses netflow-switch "IP addresses of all the interfaces must be checked to make sure none \n\ of them matches with flow export destination IP address." IPFLOW-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. netflow-switch - IPFLOW-4-V9_TEMPLATE_EXPORT 4-Warning Error creating [chars] Version 9 export template length is zero netflow-switch LOG_STD_DBG_ACTION IPMCAST_LIB_GIR-3-MCAST_GIR_CLIENT_NOT_FOUND 3-Error Failed to find multicast GIR client for vrf [chars] Failed to find multicast GIR client ipmulticast LOG_STD_ACTION IPMCAST_LIB_GIR-3-MCAST_GIR_CLIENT_NOT_FOUND 3-Error Failed to find multicast GIR client for vrf [chars] Failed to find multicast GIR client ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-DUPLICATE_RW_CONTEXT 3-Error Specified multicast route watch client registration context is already in use. The context specified for a multicast route watch client registration request is already in use. The client registration request can not be processed. Multicast traffic flow may be degraded by failure to correctly determine RPF state information. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-DUPLICATE_RW_CONTEXT 3-Error Specified multicast route watch client registration context is already in use. The context specified for a multicast route watch client registration request is already in use. The client registration request can not be processed. Multicast traffic flow may be degraded by failure to correctly determine RPF state information. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-INTERNAL_ERROR 3-Error An internal error has occured while obtaining RPF information [chars] RPF handling Internal error ipmulticast LOG_STD_RECUR_ACTION IPMCAST_LIB_RPF-3-INTERNAL_ERROR 3-Error An internal error has occured while obtaining RPF information [chars] RPF handling Internal error ipmulticast LOG_STD_RECUR_ACTION IPMCAST_LIB_RPF-3-INVALID_RW_CONTEXT 3-Error Invalid context specified for a multicast route watch client. An invalid context was specified for handling a multicast route watch update. Multicast traffic flow may be degraded by failure to correctly determine RPF state information. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-INVALID_RW_CONTEXT 3-Error Invalid context specified for a multicast route watch client. An invalid context was specified for handling a multicast route watch update. Multicast traffic flow may be degraded by failure to correctly determine RPF state information. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-RIB_REGISTER_FAIL 3-Error Failed to register with RIB multicast RPF lookups will not function Multicast could not register with RIB to obtain RPF information later. This will cause severe problem when there is multicast traffic flow since it will not be possible to obtain RPF information ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-RIB_REGISTER_FAIL 3-Error Failed to register with RIB multicast RPF lookups will not function Multicast could not register with RIB to obtain RPF information later. This will cause severe problem when there is multicast traffic flow since it will not be possible to obtain RPF information ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-RW_INIT_FAIL 3-Error Failed to START/STOP Route-watch debugging for '[chars]' Multicast could not START or STOP Route-watch debugging for the specific Address-family IPv4/IPv6 listed. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-RW_INIT_FAIL 3-Error Failed to START/STOP Route-watch debugging for '[chars]' Multicast could not START or STOP Route-watch debugging for the specific Address-family IPv4/IPv6 listed. ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-3-RW_START_FAIL 3-Error Error trying to start RPF route watch for prefix [chars] in table [dec] [chars] RPF information will not be obtained - - - IPMCAST_LIB_RPF-3-RW_START_FAIL 3-Error Error trying to start RPF route watch for prefix [chars] in table [dec] [chars] RPF information will not be obtained - - - IPMCAST_LIB_RPF-3-STOP_FAIL 3-Error Error trying to stop RPF watch for a prefix Internal error has occured while trying to stop obtaining RPF change information ipmulticast LOG_STD_RECUR_ACTION IPMCAST_LIB_RPF-3-STOP_FAIL 3-Error Error trying to stop RPF watch for a prefix Internal error has occured while trying to stop obtaining RPF change information ipmulticast LOG_STD_RECUR_ACTION IPMCAST_LIB_RPF-4-RIB_UNREGISTER_FAIL 4-Warning Multicast failed to unregister with RIB Multicast could not unregister with RIB when multicast is disabled. There will not be any existing traffic flow since multicast is already disabled. However if enabled again and if problem is seen with multicast traffic flow it should be reported ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-4-RIB_UNREGISTER_FAIL 4-Warning Multicast failed to unregister with RIB Multicast could not unregister with RIB when multicast is disabled. There will not be any existing traffic flow since multicast is already disabled. However if enabled again and if problem is seen with multicast traffic flow it should be reported ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-4-RTMGR_TOPO_ERR 4-Warning Unexpected error accessing topology specific information An internal error has occured while accessing topology specific information. The RPF information may not be obtained resulting in problems with multicast flows ipmulticast LOG_STD_ACTION IPMCAST_LIB_RPF-4-RTMGR_TOPO_ERR 4-Warning Unexpected error accessing topology specific information An internal error has occured while accessing topology specific information. The RPF information may not be obtained resulting in problems with multicast flows ipmulticast LOG_STD_ACTION IPMCAST_LIB_STR-3-MCAST_STRING_COPY_ERROR 3-Error Multicast string copy failure Multicast string copy failure ipmulticast LOG_STD_ACTION IPMCAST_LIB_STR-3-MCAST_STRING_COPY_ERROR 3-Error Multicast string copy failure Multicast string copy failure ipmulticast LOG_STD_ACTION IPMCAST_LIB_STR-4-MCAST_STRING_COPY_BUF_OVERFLOW 4-Warning Multicast string copy overflow Multicast string copy overflow ipmulticast LOG_STD_ACTION IPMCAST_LIB_STR-4-MCAST_STRING_COPY_BUF_OVERFLOW 4-Warning Multicast string copy overflow Multicast string copy overflow ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-IPMCAST_LIMIT_SYNC 3-Error Failed to sync multicast limit state to the standby RP An internal failure prevented sending of multicast limit information to the standby RP. Some multicast traffic disruption is possible following a route processor failover. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-3-IPMCAST_LIMIT_SYNC 3-Error Failed to sync multicast limit state to the standby RP An internal failure prevented sending of multicast limit information to the standby RP. Some multicast traffic disruption is possible following a route processor failover. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-3-MEMORY_ERR 3-Error Not enough memory. [chars] Memory not available for allocating requested object. ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-MEMORY_ERR 3-Error Not enough memory. [chars] Memory not available for allocating requested object. ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-TIMER_ERR 3-Error Unexpected error in the timer library: [chars] Internal error ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-TIMER_ERR 3-Error Unexpected error in the timer library: [chars] Internal error ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-VRF_CTX_ERR 3-Error [chars] Ctx: 0x[hec] Failure in updating the LIB VRF Context structures. ipmulticast LOG_STD_ACTION IPMCAST_LIB-3-VRF_CTX_ERR 3-Error [chars] Ctx: 0x[hec] Failure in updating the LIB VRF Context structures. ipmulticast LOG_STD_ACTION IPMCAST_LIB-4-IPMCAST_LIMIT 4-Warning Adding [chars] interface '[chars]' denied for [chars][chars] The maximum number of times the given interface appears as incoming or outgoing for some multicast state is reached. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-4-IPMCAST_LIMIT 4-Warning Adding [chars] interface '[chars]' denied for [chars][chars] The maximum number of times the given interface appears as incoming or outgoing for some multicast state is reached. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-4-IPMCAST_LIMIT_THRESHOLD 4-Warning [chars] interface '[chars]' for [chars][chars] [chars] %lld The maximum number of times the given interface appears as incoming or outgoing for some multicast state has reached threshold of its configured limit. ipmulticast "The configured multicast limit for some interface" " has reached the threshold of its configured mCAC" " limit. Please take proactive measures at this point" " like increasing the mCAC limit." IPMCAST_LIB-4-IPMCAST_LIMIT_THRESHOLD 4-Warning [chars] interface '[chars]' for [chars][chars] [chars] %lld The maximum number of times the given interface appears as incoming or outgoing for some multicast state has reached threshold of its configured limit. ipmulticast "The configured multicast limit for some interface" " has reached the threshold of its configured mCAC" " limit. Please take proactive measures at this point" " like increasing the mCAC limit." IPMCAST_LIB-4-UNEXPECTED_CONDITION 4-Warning Unexpected condition: [chars] An un expected condition situation state or event has been detected. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-4-UNEXPECTED_CONDITION 4-Warning Unexpected condition: [chars] An un expected condition situation state or event has been detected. ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-4-UNKNOWN_EVENT_ERR 4-Warning Unexpected event received: [dec] No handler found for event ipmulticast LOG_STD_ACTION IPMCAST_LIB-4-UNKNOWN_EVENT_ERR 4-Warning Unexpected event received: [dec] No handler found for event ipmulticast LOG_STD_ACTION IPMCAST_LIB-6-EVENT_Q_SIZE 6-Information The event queue size has exceeded [dec] Processing may become slower ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-6-EVENT_Q_SIZE 6-Information The event queue size has exceeded [dec] Processing may become slower ipmulticast LOG_STD_NO_ACTION IPMCAST_LIB-6-TIMER_BUSY 6-Information Timer drift is accumulating [dec] msecs There is large amount of processin load and the timers are accumulating delay. ipmulticast LOG_STD_RECUR_ACTION IPMCAST_LIB-6-TIMER_BUSY 6-Information Timer drift is accumulating [dec] msecs There is large amount of processin load and the timers are accumulating delay. ipmulticast LOG_STD_RECUR_ACTION IPMCAST_RPF-3-INTERNAL_ERROR 3-Error An internal error has occured while obtaining RPF information [chars] RPF handling Internal error ipmulticast LOG_STD_RECUR_ACTION IPMCAST_RPF-3-INTERNAL_ERROR 3-Error An internal error has occured while obtaining RPF information [chars] RPF handling Internal error ipmulticast LOG_STD_RECUR_ACTION IPMCAST_RPF-4-FOREIGN_VRF 4-Warning RPF for [inet] VRF [chars] resolves in a foreign VRF [chars] - - - IPMCAST_RPF-4-FOREIGN_VRF 4-Warning RPF for [inet] VRF [chars] resolves in a foreign VRF [chars] - - - IPMCAST_RPF-4-RPF_LOOKUP_LOOP 4-Warning RPF route lookup loop for [inet] A routing loop occurred during the recursive resolution of an RPF address ipmulticast "Check routing tables used for RPF" IPMCAST_RPF-4-RPF_LOOKUP_LOOP 4-Warning RPF route lookup loop for [inet] A routing loop occurred during the recursive resolution of an RPF address ipmulticast "Check routing tables used for RPF" IPMCAST_RPF-5-RPF_LISP_INIT_FAILURE 5-Notice RPF lookup: LISP registration for [chars] not completed LISP watch info initialization not ready ipmulticast LOG_STD_NO_ACTION IPMCAST_RPF-5-RPF_LISP_INIT_FAILURE 5-Notice RPF lookup: LISP registration for [chars] not completed LISP watch info initialization not ready ipmulticast LOG_STD_NO_ACTION IPMOBILE-0-IPMOBILE_DHCP 0-Emergency \ [chars] Two reasons for this error message\n\ 1. DHCP Client failed to get started this could be because of malloc\n\ failures.\n\ 2. IPMOBILE DHCP Process failed to start mobileip "If this error message is seen it is recommended not to use this\n\ HA for binding creation with DHCP Address Allocation.\n\ Check the available memory in the box and for the first reason try\n\ to get 'debug dhcp detail' before the failure.\n\ Contact your technical support representative with the error\n\ message you got." IPMOBILE-0-NOPROCESS 0-Emergency \ [chars] A Process could not be started - "Please contact your technical support representative\n\ with the error message you got and with the output of\n\ 'show process '." IPMOBILE-2-ASSERTFAILED 2-Critical IPMOBILE assertion failed: [chars] The software detected an inconsistency. This is considered a\n\ serious error. The router attempts to continue but IP Mobility\n\ processing may be impaired. mobileip "Copy the error message exactly as it appears noting any IP Mobility\n\ problems that you are experiencing and report it to your technical\n\ support representative." IPMOBILE-3-CONFIGERROR 3-Error Standby FA configuration is not in sync with the active The software detected an inconsistency in configuration between\n\ the standby and the active. Standby FA may not proceed with the\n\ sync for this visitor. mobileip "Re-configure standby FA and make sure the configuration between\n\ the standby and the active is in sync." IPMOBILE-3-NOSOCKET 3-Error Unable to open socket The requested operation could not be accomplished because of a low\n\ memory condition. mobileip "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." IPMOBILE-3-NOTUNNEL 3-Error Maximum number of tunnels [dec] reached The number of Mobile IP tunnels allowed on the box is reached. mobileip "This occures if the HA/FA is overloaded. \n\ If you suspect this condition contact technical\n\ support representative with the output of show tech" IPMOBILE-3-SA_PARSE_FAILED 3-Error Error in parsing the security association for [chars] The Mobile IP Home Agent encountered an error while processing the Security Association in the RADIUS Access-Accept message. mobileip "Check the Radius profile config for the Mobile Node for which " "the processing of the Security Association failed." IPMOBILE-5-MIP_TUNNELDELETE 5-Notice Mobile IP tunnel [chars] deleting The Mobile IP tunnel is going to be deleted. mobileip "This occurs if the active mobile ip binding is \n\ deleted.\n\ If you suspect this condition contact technical\n\ support representative with the output of show tech" IPMOBILE-6-REDUPDATEFAIL 6-Information Too many redundancy update failures [dec] in the last minute. A mobile router's attempt to dynamically add or delete a\n\ mobile network failed because that mobile network was already\n\ configured as a virtual network in the home agent. mobileip "To avoid duplication errors make sure that the virtual networks\n\ configuration on the home agent and the dynamic mobile network\n\ configuration on the mobile router do not have any overlapping\n\ network prefixes." IPMOBILE-6-SECURE 6-Information Security violation on [chars] from [chars] [chars] - errcode [chars] [dec] A security violation occurred during registration attempt. mobileip "This is for informational purpose only." IPMUX-3-V4_CACHE_FULL 3-Error IPMux V4 Cache full - replacing active entry The IPMux V4 cache is full and has replaced a current cache entry. \n\ IP Multiplexing performance may be impacted if this continues. ipmux "Increase the size of the cache using the \n\ 'ip mux cache' configuration command." IPMUX-3-V6_CACHE_FULL 3-Error IPMux V6 Cache full - replacing active entry The IPMux V6 cache is full and has replaced a current cache entry. \n\ IP Multiplexing performance may be impacted if this continues. ipmux "Increase the size of the cache using the \n\ 'ipv6 mux cache' configuration command." IPNAT_HA-3-ATTRIBUTE 3-Error Bulk sync of [chars] via [chars] [chars] is invalid for [chars] An attempt to bulk sync an address pool or a dynamic/static\n\ translation has detected that the entity which is to be sent to the\n\ standby RP when acting in a stateful redundant mode contains an\n\ invalid owner property and hence cannot be synchronized. The detection\n\ of this case will result in a failure of the bulk sync. nat LOG_STD_ACTION IPNAT_HA-3-BULK_SYNC 3-Error Failed to send [chars] information to peer - nat LOG_STD_ACTION IPNAT_HA-3-CLIENT 3-Error Failed to register with [chars] [chars] The NAT High Availability has failed to register with the specified\n\ component during initialization. This is an internal error which\n\ indicates that the NAT HA services will be unavailable. nat LOG_STD_ACTION IPNAT_HA-3-DECODE 3-Error Decode via [chars] of [chars] failed A message of the transport and type described failed in its attempt\n\ to be decoded on the standby. The resultant action taken by the\n\ standby route processor is an attempt to resynchronize. nat LOG_STD_ACTION IPNAT_HA-3-DYN_DEFERQ 3-Error [chars] failed to defer[chars] The incremental synchronization of the NAT dynamic state to the standby\n\ RP has failed to add the information to the deferral queue for later\n\ processing during the time where the standby RP is progressing to it's\n\ hot standby redundant state. This implies that the runtime state\n\ between the active and standby RP would be inconsistent once the\n\ standby has been fully initialized. nat "show ip nat ha" IPNAT_HA-3-DYN_SYNC 3-Error Failed to process [chars] dynamic state The incremental synchronization of the NAT configuration to the standby\n\ RP has failed to complete successfully. This implies that the\n\ configuration state between the active and standby RP is\n\ inconsistent. nat "show ip nat ha" IPNAT_HA-3-INTERFACE_TYPE 3-Error [chars] type/slot %lx unit %lu num %lu channel %lu value [dec] An attempt to sync a dynamic translation or address change has\n\ detected that the interface which was encoded on the active RP\n\ has a different type the standby RP. The detection of this\n\ case will result in a failure of the bulk or LBL sync. nat LOG_STD_ACTION IPNAT_HA-3-MISMATCH 3-Error [chars] [chars] mismatch with id [dec] The specified synchronization operation has failed to complete on the\n\ standby route processor due to an inconsistency in the internal id\n\ which would have resulted in an inconsistent configuration between\n\ active and standby. The resultant action taken by the standby route\n\ processor is an attempt to resynchronize. nat LOG_STD_ACTION IPNAT_HA-3-PURGE 3-Error Failed to purge [chars] information - nat LOG_STD_ACTION IPNAT_HA-3-RECEIVE 3-Error Message via [chars] is [chars] An ISSU registration for the set of initial capabilities and sessions\n\ failed due to the reason specified. This will have the effect of the\n\ NAT ISSU support being unavailable between peers. nat LOG_STD_ACTION IPNAT_HA-3-TRANSFORM 3-Error [chars] of [chars] via [chars] failed [chars] An attempt to either encode or decode a versioned synchronization\n\ message has failed due to an internal error encountered by the ISSU\n\ component. nat LOG_STD_ACTION IPNAT_HA-6-ADDR_CHANGE 6-Information [chars] unable to encode data descriptor for interface [chars] An attempt to sync an address change to the standby RP has\n\ detected that the interface which was to be encoded on the\n\ active RP is no longer present or does not support encoding. \n\ The interface may have been removed from the configuration or \n\ may not support encoding. - LOG_STD_ACTION IPNAT_HA-6-INTERFACE 6-Information [chars] type/slot %lx uint %lu num %lu channel %lu An attempt to sync a dynamic translation or address change has\n\ detected that the interface which was encoded on the active RP\n\ is not present on the standby RP. The detection of this case\n\ may result in a failure of the bulk or LBL sync. nat LOG_STD_ACTION IPNAT_HA-6-MAPPING_COMPARE 6-Information [chars] [chars] [chars] mapping id [dec] comparing [chars] [chars] [chars] mapping id [dec] The specified synchronization operation on the standby route processor\n\ has detected an internal condition with respect to the properities of\n\ dynamic mappings. This is informational. nat LOG_STD_ACTION IPNAT_HA-6-MAPPING_EXISTS 6-Information [chars] [chars] [chars] mapping id [dec] The specified synchronization operation on the standby route processor\n\ has detected the presence of an existing matching mapping. This may\n\ be associated with any observed PRC failures on the standby. nat LOG_STD_ACTION IPNAT_HA-6-READY 6-Information [chars] peer not ready discarding [chars] The synchronization attempt for the message has determined that the\n\ transport has lost communication with its peer. This is a normal\n\ situation which indicates that the standby route-processor is currently\n\ out of service implying a simplex redundancy mode. - - IPNAT_HA-6-RELOAD 6-Information [chars] reloading [chars] A synchronization attempt between the active and standby RP peers has\n\ failed with the reason indicated. The standby peer is reloaded in an\n\ attempt to resynchronize when operating in a stateful redundant\n\ mode. nat LOG_STD_ACTION IPNAT_HA-6-RELOAD_DISABLED 6-Information Standby reload has been disabled NAT RP state is out of sync and the standby should be reloaded manually The active and standby RPs are out of sync and the standby RP would have been reloaded but this reload was suppressed based on the configured environment. nat LOG_STD_ACTION IPNAT_HA-6-TIMEOUT 6-Information Bulk sync is flow controlled by [chars] The bulk synchronization of the NAT configuration to the standby RP\n\ has encountered a flow control condition which has effected a timeout\n\ awaiting the condition to clear. This will result in a reload of the\n\ standby RP to allow the bulk synchronization to restart. nat LOG_STD_ACTION IPNAT-3-BADMAPPINGTYPE 3-Error NAT mapping type [dec] for mapping statistics from platform is \n\ invalid The mapping type for passing mapping statistics from platform is \n\ not for static nor dynamic mapping type which is invalid. This \n\ condition can cause the statistic counters for NAT mapping to be\n\ inaccurate on the RP nat LOG_STD_ACTION IPNAT-3-CENTRAL_POLICY 3-Error Central policy setting failed: [chars] Central policy setting can not be changed due to incompatible configuration. nat "Remove existing NAT routes and mappings." IPNAT-3-CONFIG 3-Error Unable to [chars] the configuration of dynamic mappings An internal operation relating to the configuration of the\n\ dynamic mappings has failed. This may imply that the mapping\n\ has not been installed. nat LOG_STD_ACTION IPNAT-3-CSBNULL 3-Error Parser structure for route-map [chars] configuration is nul The parser structure for route-map configuraion is nul which is invalid. This condition can cause the new translations to fail in \n\ the data path nat LOG_STD_ACTION IPNAT-3-IF_UP 3-Error Error in sending interface UP event for [chars] to the ager process An internal operation relating to the interface UP event\n\ has failed which is unexpected. nat LOG_STD_ACTION IPNAT-3-LIMITSTATSNULL 3-Error NAT mexentry statistics structure from platform is nul The structure for passing maxentry limit statistics from platform is \n\ nul which is invalid. This condition can cause the statistic\n\ counters for NAT maxentry limit to be inaccurate on the RP nat LOG_STD_ACTION IPNAT-3-MAPPING_NULL 3-Error Unexpected NULL pointer received as input. An internal operation relating to notifying the platform about a\n\ mapping has provided an unexpected input. nat LOG_STD_ACTION IPNAT-3-MAPPINGSTATSNULL 3-Error NAT mapping statistics structure from platform is nul The structure for passing mapping statistics from platform is \n\ nul which is invalid. This condition can cause the statistic\n\ counters for NAT mapping to be inaccurate on the RP nat LOG_STD_ACTION IPNAT-3-POOLSTATSNULL 3-Error NAT pool statistics structure from platform is nul The structure for passing global/systems stats from platform \n\ is nul which is invalid. This condition can cause the statistic\n\ counters for NAT pool to be inaccurate on the RP nat LOG_STD_ACTION IPNAT-3-PORTLISTNULL 3-Error Portlist for address [inet] proto [dec] is nul The portlist for the address which requests more port blocks \n\ is nul which is invalid. This condition can cause the new \n\ translations to fail in the data path nat LOG_STD_ACTION IPNAT-3-PORTNULL 3-Error Start port or end port for port block allocation request is nul Start port or end port for port block allocation request is nul\n\ This condition can cause the new translations to fail in the \n\ data path nat LOG_STD_ACTION IPNAT-3-RTMAPNAMENULL 3-Error Route-map name for [chars] configuration is nul The route-map name is nul which is invalid. This condition can cause the new translations to fail in the data path nat LOG_STD_ACTION IPNAT-3-RTMAPNULL 3-Error route-map for configuration download is nul The route-map structure is nul which is invalid. This condition\n\ can cause the new translations to fail in the data path nat LOG_STD_ACTION IPNAT-3-SBINIT 3-Error Error initializing [chars] subblock data structure. [chars] Initialization of the specified subblock data structure could not be accomplished. nat - IPNAT-3-SYSSTATSNULL 3-Error NAT global/system statistics structure from platform is nul The structure for passing global/systems statistics from platform \n\ is nul which is invalid. This condition can cause the NAT global\n\ statistic counters in inaccurate on the RP nat LOG_STD_ACTION IPNAT-3-UNEXPECTED_ADDRESS 3-Error NULL An address contained an unexpected value. nat LOG_STD_ACTION IPNAT-3-UNEXPECTED_MAPPING_FLAG 3-Error Unexpected mapping flag %#04x received An internal operation relating to notifying the platform about a\n\ mapping has provided an unexpected input. nat LOG_STD_ACTION IPNAT-3-WLANSESSNULL 3-Error NAT WLAN session structure for session [chars] from platform is nul The structure for passing WLAN session from platform is \n\ nul which is invalid. This condition can cause the NAT WLAN\n\ session to fail in the data path nat LOG_STD_ACTION IPNAT-4-ADDR_ALLOC_FAILURE 4-Warning Address allocation failed for [inet] pool [chars] might be exhausted An address could not be allocated from the IP NAT pool. This condition can cause a translation failure and might result in packets being dropped. The counter for misses will be incremented for these packets. nat "Check to see if the NAT pool has been exhausted. To reuse any existing " "addresses in the NAT pool for new packet flows clear the current NAT " "entries using clear ip nat translation *" IPNAT-6-ENTRIES 6-Information Static translation count reset inside/outside source/destination %llu/%llu %llu/%llu Upon the removal of the last remaining static translation from the\n\ configuration it has been determined that there is a discrepancy\n\ with the internal accounting as regards the previous provisioning\n\ of inside source/destination versus outside source entries. The\n\ internal accounting has been reset to indicate that there are no\n\ translations of any type currently. nat LOG_STD_ACTION IPNAT-6-ID 6-Information [chars] identifier has wrapped The identifier which is assigned to that which is resultant from\n\ the configuration in question has cycled through the available\n\ number space and is now allocating from its initial value again. nat LOG_STD_NO_ACTION IPNAT-6-PORT_ALLOC 6-Information Port allocation via [chars] for [dec] [chars] [chars] ports min [dec] max [dec] A port allocation request for the specified range of ports has been\n\ attempted from the named party on the standby RP. This is an\n\ informational message which tracks the request source. nat LOG_STD_ACTION IPRT-2-COMPRESS 2-Critical Bad route_compress call sdb= [hec] An internal software error occurred. - LOG_STD_RECUR_ACTION IPRT-2-COMPRESS 2-Critical Bad route_compress call sdb= [hec] An internal software error occurred. - LOG_STD_RECUR_ACTION IPRT-2-IPTABLEERROR 2-Critical IP routing table [chars] initialization failure - [chars] An internal software error occurred preventing the creation of new IP routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-2-IPTABLEERROR 2-Critical IP routing table [chars] initialization failure - [chars] An internal software error occurred preventing the creation of new IP routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-BAD_MSGTYPE_ERROR 3-Error ION RIB error: [chars] [dec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BAD_MSGTYPE_ERROR 3-Error ION RIB error: [chars] [dec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BAD_PDB_HANDLE 3-Error Pdb handle error %04x %04x [hec] %08x %04x %02x RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BAD_PDB_HANDLE 3-Error Pdb handle error %04x %04x [hec] %08x %04x %02x RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BAD_PDB_INDEX 3-Error Pdb index error %08x %04x [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BAD_PDB_INDEX 3-Error Pdb index error %08x %04x [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-BADCOMLIST 3-Error Community list check with bad list [dec] A user specified an invalid BGP community list number. - "Check the system configuration to make sure that the community list " "specified falls within the valid range." IPRT-3-BADCOMLIST 3-Error Community list check with bad list [dec] A user specified an invalid BGP community list number. - "Check the system configuration to make sure that the community list " "specified falls within the valid range." IPRT-3-BADRFREG 3-Error Unable to register IP Routing as a client of RF. This is a severe error as far as IP routing NSF is concerned - "Copy the error message exactly as it appears and report it to your " "technical support representative." IPRT-3-BADRFREG 3-Error Unable to register IP Routing as a client of RF. This is a severe error as far as IP routing NSF is concerned - "Copy the error message exactly as it appears and report it to your " "technical support representative." IPRT-3-CFORK 3-Error Old-style routing processes no longer supported RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-CFORK 3-Error Old-style routing processes no longer supported RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-CSB_SAVE_DATA_BAD_MAGIC 3-Error Bad magic for CSB Data [hec] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-CSB_SAVE_DATA_BAD_MAGIC 3-Error Bad magic for CSB Data [hec] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-GETEACHROUTE_BAD_MAGIC 3-Error Bad magic for ip_geteachroute RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-GETEACHROUTE_BAD_MAGIC 3-Error Bad magic for ip_geteachroute RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-HMI_INIT_ERROR 3-Error Unable to init HMI database RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-HMI_INIT_ERROR 3-Error Unable to init HMI database RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-INCONSISTENT_TOPOID_ERROR 3-Error Inconsistent topology id topoid:0x[hec] and topoid:0x[hec] are found for the topology[chars] - - - IPRT-3-INCONSISTENT_TOPOID_ERROR 3-Error Inconsistent topology id topoid:0x[hec] and topoid:0x[hec] are found for the topology[chars] - - - IPRT-3-INVALID_NEXTHOP 3-Error [chars] ID 0x[hec] [inet]%m from [chars] Gwy: [inet] [chars] Binding Label: [chars] Type:0x[hec] Attr 0x[hec] Has Repair Path: [dec] Repair Gwy: [inet] [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-INVALID_NEXTHOP 3-Error [chars] ID 0x[hec] [inet]%m from [chars] Gwy: [inet] [chars] Binding Label: [chars] Type:0x[hec] Attr 0x[hec] Has Repair Path: [dec] Repair Gwy: [inet] [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-INVALID_RIBUPDATE_STATE 3-Error Invalid RIB State for update 0x[hec] [inet]%m [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-INVALID_RIBUPDATE_STATE 3-Error Invalid RIB State for update 0x[hec] [inet]%m [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-INVALIDTOPO 3-Error Bad topology [chars] table in static routing entry [inet]%m An error has occurred when a static route failed to find corresponding topology routing table. - LOG_STD_RECUR_ACTION IPRT-3-INVALIDTOPO 3-Error Bad topology [chars] table in static routing entry [inet]%m An error has occurred when a static route failed to find corresponding topology routing table. - LOG_STD_RECUR_ACTION IPRT-3-INVALIDVRF_BFD 3-Error Bad vrf_id 0x[hec] in static BFD neighbor [chars] [inet] A static BFD neighbor failed to find corresponding vrf. - LOG_STD_RECUR_ACTION IPRT-3-INVALIDVRF_BFD 3-Error Bad vrf_id 0x[hec] in static BFD neighbor [chars] [inet] A static BFD neighbor failed to find corresponding vrf. - LOG_STD_RECUR_ACTION IPRT-3-IPDB_DEL_ERROR 3-Error i_pdb delete error [chars] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-IPDB_DEL_ERROR 3-Error i_pdb delete error [chars] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-IPTABLEINIT 3-Error IP routing table creation failure - [chars] An internal software error occurred preventing the creation of new IP routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-IPTABLEINIT 3-Error IP routing table creation failure - [chars] An internal software error occurred preventing the creation of new IP routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-MAXALLOWEDLIMITREACHED 3-Error Maximum allowed static route count reached: [dec] \n ip_addstatic_route failed \n The maximum number of static routes that can be configured is reached. No further routes will be added to the table - "Remove the unwanted static routes to add more routes" IPRT-3-MAXALLOWEDLIMITREACHED 3-Error Maximum allowed static route count reached: [dec] \n ip_addstatic_route failed \n The maximum number of static routes that can be configured is reached. No further routes will be added to the table - "Remove the unwanted static routes to add more routes" IPRT-3-NDB_BAD_MAGIC 3-Error Bad magic for NDB structure [hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_BAD_MAGIC 3-Error Bad magic for NDB structure [hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_CREATE_ERROR 3-Error Error creating an NDB - [chars] [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_CREATE_ERROR 3-Error Error creating an NDB - [chars] [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_DEL_ERROR 3-Error Error Removing an NDB [chars] [inet]%m tid 0x[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_DEL_ERROR 3-Error Error Removing an NDB [chars] [inet]%m tid 0x[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_NRP_IN_PROGRESS 3-Error Invalid action on NDB while in NRP in progress: [chars] 0x[hec] [inet]%m state [dec] flags [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_NRP_IN_PROGRESS 3-Error Invalid action on NDB while in NRP in progress: [chars] 0x[hec] [inet]%m state [dec] flags [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_ONQ 3-Error Queue elem on queue - [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_ONQ 3-Error Queue elem on queue - [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_PDB_MATCH_INVALID 3-Error Invalid ndb_pdb_match_type 0x[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_PDB_MATCH_INVALID 3-Error Invalid ndb_pdb_match_type 0x[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_REPLIC_INVALID_OP 3-Error Invalid operation on replicated NDB [chars]: RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-NDB_REPLIC_INVALID_OP 3-Error Invalid operation on replicated NDB [chars]: RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-NDB_STATE_ERROR 3-Error NDB state error [chars] 0x[hec] [inet]%m state [dec] event [hec]->[hec] nh_type [hec] flags [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDB_STATE_ERROR 3-Error NDB state error [chars] 0x[hec] [inet]%m state [dec] event [hec]->[hec] nh_type [hec] flags [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDBSHR_BAD_MAGIC 3-Error Bad magic for NDBSHR structure [hec]/[hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NDBSHR_BAD_MAGIC 3-Error Bad magic for NDBSHR structure [hec]/[hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NEXTHOPS_LIST_ERROR 3-Error [chars]: [inet]%m [dec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NEXTHOPS_LIST_ERROR 3-Error [chars]: [inet]%m [dec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NEXTHOPS_LIST_MISMATCH 3-Error [chars]: [chars] [inet]%m nhtype: [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NEXTHOPS_LIST_MISMATCH 3-Error [chars]: [chars] [inet]%m nhtype: [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_BACKUP_MEM 3-Error No Backup Route memory available for [chars] The addition of a Backup Route failed because of a low memory condition. Backup may not be available if the Primary Route is removed - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NO_BACKUP_MEM 3-Error No Backup Route memory available for [chars] The addition of a Backup Route failed because of a low memory condition. Backup may not be available if the Primary Route is removed - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NO_MAJORNET_NDB 3-Error No majornet found: [chars] [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_MAJORNET_NDB 3-Error No majornet found: [chars] [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_PDB_INDEX 3-Error Pdb index not available for [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_PDB_INDEX 3-Error Pdb index not available for [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_REPLIC_MEM 3-Error No Route Replication memory available for [inet]%m The replication of a Route failed because of a low memory condition. The route will not be replicated in the destination table at this time. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NO_REPLIC_MEM 3-Error No Route Replication memory available for [inet]%m The replication of a Route failed because of a low memory condition. The route will not be replicated in the destination table at this time. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NO_RIB_TABLE 3-Error RIB table lookup failure: [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NO_RIB_TABLE 3-Error RIB table lookup failure: [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NOMEMORY 3-Error No memory available for [chars] The requested operation failed because of a low memory condition. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NOMEMORY 3-Error No memory available for [chars] The requested operation failed because of a low memory condition. - "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPRT-3-NOTEXIST_BFD 3-Error Static BFD neighbor does not exist: [chars] [chars] [inet] Failed to find corresponding static BFD neighbor. - LOG_STD_RECUR_ACTION IPRT-3-NOTEXIST_BFD 3-Error Static BFD neighbor does not exist: [chars] [chars] [inet] Failed to find corresponding static BFD neighbor. - LOG_STD_RECUR_ACTION IPRT-3-NOTREG_BFD 3-Error Unexpected reachability notification: [chars] [chars] [inet] Gateway is not tracked by BFD. - LOG_STD_RECUR_ACTION IPRT-3-NOTREG_BFD 3-Error Unexpected reachability notification: [chars] [chars] [inet] Gateway is not tracked by BFD. - LOG_STD_RECUR_ACTION IPRT-3-NOTSAMEOWNER 3-Error SAME_PROTO dist_status [dec] from [chars] for route owned by [chars] - - - IPRT-3-NOTSAMEOWNER 3-Error SAME_PROTO dist_status [dec] from [chars] for route owned by [chars] - - - IPRT-3-NULL_NDB 3-Error Unexpected null NDB RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_NDB 3-Error Unexpected null NDB RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_NDBSHR 3-Error Unexpected null NDBSHR [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_NDBSHR 3-Error Unexpected null NDBSHR [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_RDB 3-Error Unexpected null RDB RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_RDB 3-Error Unexpected null RDB RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_RDBSHR 3-Error Unexpected null RDBSHR [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-NULL_RDBSHR 3-Error Unexpected null RDBSHR [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PARSER_REG_ERROR 3-Error Unable to register [chars] submode translation callback mode = 0x%X RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PARSER_REG_ERROR 3-Error Unable to register [chars] submode translation callback mode = 0x%X RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PATHIDX 3-Error Bad path pointer of [hec] for [inet] [dec] max A software error occurred. - LOG_STD_ACTION IPRT-3-PATHIDX 3-Error Bad path pointer of [hec] for [inet] [dec] max A software error occurred. - LOG_STD_ACTION IPRT-3-PDB_DEL_ERROR 3-Error Pdb delete error [chars] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PDB_DEL_ERROR 3-Error Pdb delete error [chars] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PDB_STATIC_ERROR 3-Error Static pdb procinfo is NULL RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-PDB_STATIC_ERROR 3-Error Static pdb procinfo is NULL RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_INVALID_ACL_TYPE 3-Error Invalid ACL type [dec] is configured. RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_INVALID_ACL_TYPE 3-Error Invalid ACL type [dec] is configured. RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_ROUTE_MAP_CONFIG_ERROR 3-Error Protocol filter routemap [chars] configuration failed RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_ROUTE_MAP_CONFIG_ERROR 3-Error Protocol filter routemap [chars] configuration failed RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_SB_ADD_ERROR 3-Error Topology 0x[hec] interface [chars] add sub-block failed for sb_type [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-PROTOFLTR_SB_ADD_ERROR 3-Error Topology 0x[hec] interface [chars] add sub-block failed for sb_type [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RDB_BAD_MAGIC 3-Error Bad magic for RDB structure [hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RDB_BAD_MAGIC 3-Error Bad magic for RDB structure [hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RDBSHR_BAD_MAGIC 3-Error Bad magic for RDBSHR structure [hec]/[hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RDBSHR_BAD_MAGIC 3-Error Bad magic for RDBSHR structure [hec]/[hec]/[hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RESPAWN_COUNT_ERROR 3-Error Unable to get process respawn count RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RESPAWN_COUNT_ERROR 3-Error Unable to get process respawn count RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-RIB_ACC_HDLR_INIT 3-Error Error Registering [chars] RIB handlers with RIB Access Infra An internal software error occurred preventing Access to RIB Data. ribinfra "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-RIB_ACC_HDLR_INIT 3-Error Error Registering [chars] RIB handlers with RIB Access Infra An internal software error occurred preventing Access to RIB Data. ribinfra "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-RIB_INTERNAL_ERR 3-Error [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-RIB_INTERNAL_ERR 3-Error [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-3-RIB_LOOP 3-Error Resolution loop formed by routes in RIB RIB route producers have installed routes in the RIB that form a loop during resolution. - "Resolve the RIB route resolution loop:\n" "1 Determine which routes are involved in the loop by issuing the " IPRT-3-RIB_LOOP 3-Error Resolution loop formed by routes in RIB RIB route producers have installed routes in the RIB that form a loop during resolution. - "Resolve the RIB route resolution loop:\n" "1 Determine which routes are involved in the loop by issuing the " IPRT-3-RIBTABLEERROR 3-Error RIB error [dec] on [chars] - [chars] An internal software error occurred processing an event associated with a routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-RIBTABLEERROR 3-Error RIB error [dec] on [chars] - [chars] An internal software error occurred processing an event associated with a routing table. - "Copy the message exactly as it appears and report it to your " "technical support representative." IPRT-3-ROUTEINSERTERROR 3-Error Error inserting routing entry [inet]%m into IP [chars] routing table An error has occurred when a routing entry was being inserted into the IP routing table. - LOG_STD_RECUR_ACTION IPRT-3-ROUTEINSERTERROR 3-Error Error inserting routing entry [inet]%m into IP [chars] routing table An error has occurred when a routing entry was being inserted into the IP routing table. - LOG_STD_RECUR_ACTION IPRT-3-ROUTELIMITEXCEEDED 3-Error IP routing table limit exceeded - [chars] The number of routes in the named IP routing table has reached the configured limit. No further routes will be added to the table - "Reduce the number of routes in the table or reconfigure the limit" IPRT-3-ROUTELIMITEXCEEDED 3-Error IP routing table limit exceeded - [chars] The number of routes in the named IP routing table has reached the configured limit. No further routes will be added to the table - "Reduce the number of routes in the table or reconfigure the limit" IPRT-3-ROUTELIMITWARNING 3-Error IP routing table limit warning - [chars] The number of routes in the named IP routing table has reached the configured warning limit. - "Reduce the number of routes in the table or reconfigure the limit" IPRT-3-ROUTELIMITWARNING 3-Error IP routing table limit warning - [chars] The number of routes in the named IP routing table has reached the configured warning limit. - "Reduce the number of routes in the table or reconfigure the limit" IPRT-3-ROUTEREPLACEERROR 3-Error Error replacing route to [inet]%m with better route in IP [chars] routing table Copy the message exactly as it appears and report it to your technical support representative. - LOG_STD_RECUR_ACTION IPRT-3-ROUTEREPLACEERROR 3-Error Error replacing route to [inet]%m with better route in IP [chars] routing table Copy the message exactly as it appears and report it to your technical support representative. - LOG_STD_RECUR_ACTION IPRT-3-STATIC_GWIF_INCONSISTENCE 3-Error Inconsistence static route database [chars] [chars] [inet] - - - IPRT-3-STATIC_GWIF_INCONSISTENCE 3-Error Inconsistence static route database [chars] [chars] [inet] - - - IPRT-3-STATIC_SR_POLICY_INCONSISTENCE 3-Error Inconsistence static route database due to [chars] on [inet]%m via policy [chars] [dec] - - - IPRT-3-STATIC_SR_POLICY_INCONSISTENCE 3-Error Inconsistence static route database due to [chars] on [inet]%m via policy [chars] [dec] - - - IPRT-3-STATICDBINCONSISTENCE 3-Error Inconsistent static route database due to [chars] on [inet]%m on [chars] via [inet] An error has occurred due to inconsistence on static route table. - LOG_STD_RECUR_ACTION IPRT-3-STATICDBINCONSISTENCE 3-Error Inconsistent static route database due to [chars] on [inet]%m on [chars] via [inet] An error has occurred due to inconsistence on static route table. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_ADDFAILED 3-Error Failed to add static route to database [chars] on [inet]%m on [chars] via [inet] An error has occurred due to failed add on static route table. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_ADDFAILED 3-Error Failed to add static route to database [chars] on [inet]%m on [chars] via [inet] An error has occurred due to failed add on static route table. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_FAILED_RW_START 3-Error Failed to start route watch for topology [chars] gateway [inet]%m flag 0x[hec] rc [dec] An error has occurred failed to start route watch for this static route. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_FAILED_RW_START 3-Error Failed to start route watch for topology [chars] gateway [inet]%m flag 0x[hec] rc [dec] An error has occurred failed to start route watch for this static route. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_FAILED_RW_STOP 3-Error Failed to stop route watch for static route handle [hec] route watch handle [hec] gateway [inet] interface [chars] rc [dec] An error has occurred due to failed to stop route watch for this static route. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_FAILED_RW_STOP 3-Error Failed to stop route watch for static route handle [hec] route watch handle [hec] gateway [inet] interface [chars] rc [dec] An error has occurred due to failed to stop route watch for this static route. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_GET_INFO 3-Error Failed to get the route info through route watch An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_GET_INFO 3-Error Failed to get the route info through route watch An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_LOOP 3-Error Route watch failed to determine to keep a loop or not An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_LOOP 3-Error Route watch failed to determine to keep a loop or not An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_SIG 3-Error Failed to get the correct route watch signature [hec] An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_RWATCH_FAILED_SIG 3-Error Failed to get the correct route watch signature [hec] An internal error has occurred which could cause inconsistence routing table due to route watch - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_TOPOLOCK 3-Error Unable to lock topology [chars] table in static route An error has occurred when a static route failed to lock corresponding topology routing table. - LOG_STD_RECUR_ACTION IPRT-3-STATICROUTES_TOPOLOCK 3-Error Unable to lock topology [chars] table in static route An error has occurred when a static route failed to lock corresponding topology routing table. - LOG_STD_RECUR_ACTION IPRT-3-TOPO_HANDLE_ERROR 3-Error Unable to get topology handler topoid = [dec] [chars] RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-TOPO_HANDLE_ERROR 3-Error Unable to get topology handler topoid = [dec] [chars] RIB_INT_ERR_EXPLANATION ip LOG_STD_RECUR_ACTION IPRT-3-VIAUPD_ALLOC_ERROR 3-Error Error allocating [dec] next hops for [inet]%m via [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-VIAUPD_ALLOC_ERROR 3-Error Error allocating [dec] next hops for [inet]%m via [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-VIAUPD_ERROR 3-Error Error [dec] inserting additional path for [inet]%m via [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-3-VIAUPD_ERROR 3-Error Error [dec] inserting additional path for [inet]%m via [inet]%m RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-BADRIBDB 4-Warning Attempt to remove a next hop from the wrong table. Attempted: [chars] should be: [chars] prefix: [inet] Attempt to remove a next hop from the wrong routing table - LOG_STD_RECUR_ACTION IPRT-4-BADRIBDB 4-Warning Attempt to remove a next hop from the wrong table. Attempted: [chars] should be: [chars] prefix: [inet] Attempt to remove a next hop from the wrong routing table - LOG_STD_RECUR_ACTION IPRT-4-BADTRACKOBJECTTYPE 4-Warning can't track this type of object Route maps only support STATE type track objects. This object is not a STATE object - "Reconfigure the track object to make it a STATE object." IPRT-4-BADTRACKOBJECTTYPE 4-Warning can't track this type of object Route maps only support STATE type track objects. This object is not a STATE object - "Reconfigure the track object to make it a STATE object." IPRT-4-INVALID_NRP_CONTEXT 4-Warning Invalid context type: [dec] state: [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-INVALID_NRP_CONTEXT 4-Warning Invalid context type: [dec] state: [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-NDB_STATE_CHANGE 4-Warning NDB state change: [inet]%m [hec]->[hec] [dec]->[dec] [hec] refcnt [dec] tid [dec] cnt [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-NDB_STATE_CHANGE 4-Warning NDB state change: [inet]%m [hec]->[hec] [dec]->[dec] [hec] refcnt [dec] tid [dec] cnt [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RECURSIVE_ERASE 4-Warning Recursive erase [dec] [hec]/[hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RECURSIVE_ERASE 4-Warning Recursive erase [dec] [hec]/[hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPRT-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPRT-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPRT-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPRT-4-RIB_DEBUG_ERROR 4-Warning Generic RIB error: [hec] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RIB_DEBUG_ERROR 4-Warning Generic RIB error: [hec] [hec] [hec] [hec] [hec] [hec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RIB_DELETE_PENDING_ERROR 4-Warning RIB Marked Delete Pending in wrong state: [hec] [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RIB_DELETE_PENDING_ERROR 4-Warning RIB Marked Delete Pending in wrong state: [hec] [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-ROUTECOUNTNEGATIVE 4-Warning IP route counter negative - [chars] [inet] Attempt: [dec] Attempt to decrement IP route counter into negative value ribinfra "Use "clear ip route *" command to reset the route counter. If " "the message still comes out consistently copy the messages exactly " "as they appear and report it to your technical support " "representative." IPRT-4-ROUTECOUNTNEGATIVE 4-Warning IP route counter negative - [chars] [inet] Attempt: [dec] Attempt to decrement IP route counter into negative value ribinfra "Use "clear ip route *" command to reset the route counter. If " "the message still comes out consistently copy the messages exactly " "as they appear and report it to your technical support " "representative." IPRT-4-RWATCH_BFDNEIGHBOR_CREATE_ERROR 4-Warning RIB Rwatch failed to create bfd neighbor session proctype [dec] src_topoid [hec] dst_topoid [hec] [chars][chars][chars] neighbor [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RWATCH_BFDNEIGHBOR_CREATE_ERROR 4-Warning RIB Rwatch failed to create bfd neighbor session proctype [dec] src_topoid [hec] dst_topoid [hec] [chars][chars][chars] neighbor [chars] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RWATCH_BFDNEIGHBOR_SESS_WAVL_INSERT_ERROR 4-Warning RIB Rwatch failed to insert bfd neighbor session into WAVL tree proctype [dec] topoid [hec] [chars] neighbor [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_BFDNEIGHBOR_SESS_WAVL_INSERT_ERROR 4-Warning RIB Rwatch failed to insert bfd neighbor session into WAVL tree proctype [dec] topoid [hec] [chars] neighbor [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_NEIGHBOR_WAVL_DELETE_ERROR 4-Warning RIB Rwatch neighbor not found in WAVL tree for deletion client : [chars] topoid : [hec] interface : [chars] binding label: [chars] address : [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_NEIGHBOR_WAVL_DELETE_ERROR 4-Warning RIB Rwatch neighbor not found in WAVL tree for deletion client : [chars] topoid : [hec] interface : [chars] binding label: [chars] address : [chars] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_TRKSN_DELETE_ERROR 4-Warning RIB Rwatch tracked sequence number [dec] not found for client : [chars] topoid : [hec] prefix : [chars] prefix_len : [dec] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_TRKSN_DELETE_ERROR 4-Warning RIB Rwatch tracked sequence number [dec] not found for client : [chars] topoid : [hec] prefix : [chars] prefix_len : [dec] RIB_INT_ERR_EXPLANATION ribinfra LOG_STD_RECUR_ACTION IPRT-4-RWATCH_UPCALL_INIT_ERROR 4-Warning RIB Rwatch failed to initialize the upcall table afi [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RWATCH_UPCALL_INIT_ERROR 4-Warning RIB Rwatch failed to initialize the upcall table afi [dec] RIB_INT_ERR_EXPLANATION - LOG_STD_RECUR_ACTION IPRT-4-RWATCHUSAGEWARN 4-Warning Route watch client-[chars] is calling the API from RIB context !! Improper usage of the API spotted from the caller.\n Check if the api was called directly from a notification callback - "Ideal usage is to enqueue the RWATCH notifications to a client process and the api should be called from client context" IPRT-4-RWATCHUSAGEWARN 4-Warning Route watch client-[chars] is calling the API from RIB context !! Improper usage of the API spotted from the caller.\n Check if the api was called directly from a notification callback - "Ideal usage is to enqueue the RWATCH notifications to a client process and the api should be called from client context" IPRT-5-STATICROUTES_BFD_EVENT 5-Notice BFD session [chars][[chars]] An ipv4 static route BFD session has either come up or gone down \n The message describes the change for it. This message appears only if the log command is configured for the ipv4 static route BFD process. - "This informational message normally appears as routers and \n\ ipv4 static route BFD sessions go up or down." IPRT-5-STATICROUTES_BFD_EVENT 5-Notice BFD session [chars][[chars]] An ipv4 static route BFD session has either come up or gone down \n The message describes the change for it. This message appears only if the log command is configured for the ipv4 static route BFD process. - "This informational message normally appears as routers and \n\ ipv4 static route BFD sessions go up or down." IPRT-6-DELETEINGTOP 6-Information topology [chars] is deleting in static routing entry [inet]%m A static route found a corresponding deleting topology routing table. - "The action is not taken due to topology deleting state" IPRT-6-DELETEINGTOP 6-Information topology [chars] is deleting in static routing entry [inet]%m A static route found a corresponding deleting topology routing table. - "The action is not taken due to topology deleting state" IPRT-6-STATICROUTESACROSSTOPO 6-Information Cannot install inter- topology static route [inet]%m topology [chars] on outgoing interface [chars] Restricting the access of static routes that point across topologies - "Remove the static routes that are pointing accross topology interfaces" IPRT-6-STATICROUTESACROSSTOPO 6-Information Cannot install inter- topology static route [inet]%m topology [chars] on outgoing interface [chars] Restricting the access of static routes that point across topologies - "Remove the static routes that are pointing accross topology interfaces" IPRT-6-STATICROUTESACROSSVRF 6-Information Un-installing static route [inet]%m from [chars] routing table with outgoing interface [chars] Restricting the access of static routes that point across vrfs - "Remove the static routes that are pointing accross VRF interfaces" IPRT-6-STATICROUTESACROSSVRF 6-Information Un-installing static route [inet]%m from [chars] routing table with outgoing interface [chars] Restricting the access of static routes that point across vrfs - "Remove the static routes that are pointing accross VRF interfaces" IPSEC-3-ANTI_REPLAY 3-Error SA 0x[hec]0x[hec] Anti Replay check failed for the SA. cpp-ucode LOG_STD_ACTION IPSEC-3-CHUNK_CREATE_FAIL 3-Error - Chunk creation failed cpp-ucode LOG_STD_ACTION IPSEC-3-CHUNK_DESTROY_ERROR 3-Error - Chunk destroy error force cleanup cpp-ucode LOG_STD_ACTION IPSEC-3-CHUNK_DESTROY_FAIL 3-Error - Chunk destroy failed cpp-ucode LOG_STD_ACTION IPSEC-3-DROP 3-Error result type 0x[hec] Classification results in Drop. cpp-ucode LOG_STD_ACTION IPSEC-3-FOR_US_CLEARTEXT_POLICY_FAIL 3-Error - Policy fail for For-Us cleartext packet. cpp-ucode LOG_STD_ACTION IPSEC-3-FRAG_ERROR 3-Error IPSec SA received fragmented ESP packet DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec] Fragmented ESP packet is received for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-FRAG_ERROR_IPV6 3-Error IPSec SA received fragmented ESP packet DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec] Fragmented ESP packet is received for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-FRAG_MPASS 3-Error - Multipass Error cpp-ucode LOG_STD_ACTION IPSEC-3-HMAC_ERROR 3-Error IPSec SA receives HMAC error DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec] HMAC calculation error is encountered for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-HMAC_ERROR_V6 3-Error IPSec SA receives HMAC error DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec] HMAC calculation error is encountered for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-IKE_TED_MSG_LIMIT 3-Error cnt [dec] sp 0x[hec] cp sp 0x[hec] IKE TED Message Limit exceeded. cpp-ucode LOG_STD_ACTION IPSEC-3-IKE_TED_MSG_RATE 3-Error cnt [dec] sp 0x[hec] cp sp 0x[hec] IKE TED Message Rate exceeded. cpp-ucode LOG_STD_ACTION IPSEC-3-IN_POLICY_FAIL 3-Error out sa 0x[hec]0x[hec] out sp 0x[hec]0x[hec] in sa 0x[hec]0x[hec] in sp 0x[hec]0x[hec] In-Out SP mis-match. cpp-ucode LOG_STD_ACTION IPSEC-3-IN_POLICY_MISS 3-Error sa 0x[hec] cp sa 0x[hec] TCAM miss. cpp-ucode LOG_STD_ACTION IPSEC-3-INTF_NOT_CFG 3-Error - Got an encrypted packet on an interface on which ipsec is not configured. cpp-ucode LOG_STD_ACTION IPSEC-3-INVALID_PROT 3-Error invalid ipsec prot 0x[hec] Got an invalid IPSEC protocol value. cpp-ucode LOG_STD_ACTION IPSEC-3-INVALID_SA 3-Error sa 0x[hec] cp sa 0x[hec] SA is invalid. cpp-ucode LOG_STD_ACTION IPSEC-3-INVALID_SPI 3-Error spi 0x[hec] Got an invalid SPI value. cpp-ucode LOG_STD_ACTION IPSEC-3-INVALID_VAL 3-Error val 0x[hec] Invalid value seen. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_ERR_SA 3-Error rc 0x[hec] An error has occurred sending SA Byte Lifetime expiry event. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_HANDLER_ERR 3-Error rc 0x[hec] Error setting IPC Handler. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_INVALID_MSG_LEN 3-Error [dec]:[dec] len [dec] flags 0x[hec] source [dec] Invalid IPC message length cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_PAK_ALLOC 3-Error sp 0x[hec] cp sp 0x[hec] IPC pak allocation failed. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_PAK_ALLOC_SA_EVENT 3-Error event 0x[hec] sa 0x%llx IPC pak allocation failed. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_PAK_SEND 3-Error rc 0x[hec] sp 0x[hec] cp sp 0x[hec] IPC send failed. cpp-ucode LOG_STD_ACTION IPSEC-3-IPC_PAK_SEND_SA_EVENT 3-Error rc 0x[hec] event 0x[hec] sa 0x%llx IPC send failed. cpp-ucode LOG_STD_ACTION IPSEC-3-MEM_ALLOC_REACHED_LIMIT 3-Error IPC type 0x[hec] Cannot allocate more memory to store state for IPSec Traffic reached upper limit. cpp-ucode LOG_STD_ACTION IPSEC-3-MEM_EXTEND_FAILED 3-Error IPC type 0x[hec] Extending memory failed cpp-ucode LOG_STD_ACTION IPSEC-3-MEM_REQ_FAILED 3-Error IPC type 0x[hec] Requesting more memory failed. cpp-ucode LOG_STD_ACTION IPSEC-3-NO_MEMORY 3-Error No memory 0x[hec] No memory to send response back. cpp-ucode LOG_STD_ACTION IPSEC-3-PKT_TOO_BIG 3-Error IPSec Packet size [dec] larger than maximum supported size [dec] hence dropping it Maximum size for packet with IPSEC encapsulation is 9K This packet exceeded the size limit hence dropping it. qfp-ipsec LOG_STD_ACTION IPSEC-3-RECVD_PKT_NOT_IPSEC 3-Error Rec'd packet not an IPSEC packet dest_addr= %Ci src_addr= %Ci prot= [dec]\n Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated. qfp-ipsec LOG_STD_ACTION IPSEC-3-RECVD_PKT_NOT_IPSECV6 3-Error Rec'd packet not an IPSEC packet dest_addr= [ipv6_addr] src_addr= [ipv6_addr] prot= [dec]\n Rec'd packet matched crypto map ACL but is not IPSEC-encapsulated. qfp-ipsec LOG_STD_ACTION IPSEC-3-REPLAY_ERROR 3-Error IPSec SA receives anti-replay error DP Handle [dec] src_addr %Ci dest_addr %Ci SPI 0x[hec] Anti-replay error is encountered for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-REPLAY_ERROR_IPV6 3-Error IPSec SA receives anti-replay error DP Handle [dec] ipv6 src_addr [ipv6_addr] ipv6 dest_addr [ipv6_addr] SPI 0x[hec] Anti-replay error is encountered for this IPSec session. qfp-ipsec LOG_STD_ACTION IPSEC-3-SA_HARD_BYTE 3-Error SA 0x[hec]0x[hec] SA Hardbyte Lifetime expiry event. cpp-ucode LOG_STD_ACTION IPSEC-3-SA_NOT_FOUND 3-Error - SA not found. cpp-ucode LOG_STD_ACTION IPSEC-3-SA_SOFT_BYTE 3-Error SA 0x[hec]0x[hec] SA Softbyte Lifetime expiry event. cpp-ucode LOG_STD_ACTION IPSEC-3-SEQNO_OVERFLOW 3-Error SA 0x[hec]0x[hec] Sequence Number overflow for the SA. cpp-ucode LOG_STD_ACTION IPSEC-3-TRANSIT_POLICY_FAIL 3-Error - Policy fail for transit ipsec packet. cpp-ucode LOG_STD_ACTION IPSEC-3-UNEXPECTED_ERROR 3-Error orh.w0 0x[hec] error_op 0x[hec] SA 0x[hec]0x[hec] Unexpected error for the SA. cpp-ucode LOG_STD_ACTION IPSECV6-4-PKT_PROTOCOL_MISMATCH 4-Warning IP protocol in packet mismatched with tunnel mode packet from [chars] to [chars] dropped by [chars] We tried to send an IPv4 packet into an IPSec-IPv6 tunnel or an IPv6 packet into an IPSec-IPv4 tunnel. The tunnel cannot handle this type of packet and so the packet is dropped. - "Modify the tunnel configuration either by removing the" " incorrect IP address type from the tunnel interface or by" " changing the tunnel mode to match the IP address type." IPSECV6-4-PKT_PROTOCOL_MISMATCH 4-Warning IP protocol in packet mismatched with tunnel mode packet from [chars] to [chars] dropped by [chars] We tried to send an IPv4 packet into an IPSec-IPv6 tunnel or an IPv6 packet into an IPSec-IPv4 tunnel. The tunnel cannot handle this type of packet and so the packet is dropped. - "Modify the tunnel configuration either by removing the" " incorrect IP address type from the tunnel interface or by" " changing the tunnel mode to match the IP address type." IPSECV6-4-RECVD_PKT_NOT_IPSECV6 4-Warning Rec'd packet not an IPSEC packet.\n \tip dest_addr= %P src_addr= %P prot= [dec] - - - IPSECV6-4-RECVD_PKT_NOT_IPSECV6 4-Warning Rec'd packet not an IPSEC packet.\n \tip dest_addr= %P src_addr= %P prot= [dec] - - - IPSECV6-4-RECVD_PKT_V6_INV_PROT 4-Warning decapsulate: packet missing [chars] destadr=%P actual prot=[dec] Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event. - "Contact the peer's administrator." IPSECV6-4-RECVD_PKT_V6_INV_PROT 4-Warning decapsulate: packet missing [chars] destadr=%P actual prot=[dec] Rec'd IPSEC packet missing an expected AH or ESP header The peer is sending packets that don't match the negotiated security policy. Some might consider this a hostile event. - "Contact the peer's administrator." IPSECV6-4-RECVD_PKT_V6_INV_SPI 4-Warning decaps: rec'd IPSEC packet has invalid spi for\n \tdestaddr=%P prot=[dec] spi=0x[hec][dec] srcaddr=%P - - - IPSECV6-4-RECVD_PKT_V6_INV_SPI 4-Warning decaps: rec'd IPSEC packet has invalid spi for\n \tdestaddr=%P prot=[dec] spi=0x[hec][dec] srcaddr=%P - - - IPSECV6-4-RECVD_PKT_V6_MSG_LEN_ERR 4-Warning decapsulate: packet has bad [chars] length destadr=%P prot=[dec] len=[dec] Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event. - "Contact the peer's administrator." IPSECV6-4-RECVD_PKT_V6_MSG_LEN_ERR 4-Warning decapsulate: packet has bad [chars] length destadr=%P prot=[dec] len=[dec] Rec'd IPSEC packet is malformed: possibly encapsulation error? The peer is sending malformed packets. It may be due to a decryption error. Some might consider this a hostile event. - "Contact the peer's administrator." IPV4_FORWARDING-2-CAUSE_THROTTLE_ERR 2-Critical Allocation of ipv4 throttle [chars] memory failed Allocation of memory resource use by ipv4 throttle fail cpp-ucode LOG_STD_ACTION IPV4_FORWARDING-3-CAUSE_LINKTYPE_ERR 3-Error Unsupported link type - linktype = [dec] dropping packet Link type is unsupported at the current time. cpp-ucode LOG_STD_ACTION IPV4_FORWARDING-3-TABLE_ID_SZ_ERR 3-Error Table ID size configured incorrectly: [dec] Table ID size must be less than or equal to 16 or 32 bits. cpp-ucode LOG_STD_ACTION IPV4_FORWARDING-3-TRAFFIC_IDX_ERR 3-Error Traffic index invalid value: [dec] Buckets allocated: [dec] Traffic index is greater than or equal to the buckets allocated cpp-ucode LOG_STD_ACTION IPV4_FORWARDING-4-CHECKSUM_ERR 4-Warning Checksum buffer walk failed Internal problem occured during calculating segmented packet checksum. cpp-ucode LOG_STD_ACTION IPV4_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_EXTEND_FAILED 3-Error - Increasing of fragment information pool failed. cpp-ucode LOG_STD_ACTION IPV4_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_INIT_FAILED 3-Error - Initialization of fragment information pool failed. cpp-ucode LOG_STD_ACTION IPV4_REASS_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION IPV4_REASS_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION IPV4_URPF-4-DROP 4-Warning Dropping [chars] from [chars] This message indicates that the router dropped a packet due to Unicast Reverse Path Forwarding check failure qfp-ipucast "This is an informational message" IPV4_VFR-4-CONFIG 4-Warning Dropping [chars] from [chars] due to system config. This message indicates that the router drops fragment packet due to ip virtual-reassembly drop-fragments qfp-ipucast "This is an informational message" IPV4_VFR-4-FRAG_TABLE_OVERFLOW 4-Warning Dropping [chars] from [chars] due to fragment table overflow. This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ip virtual-reassembly max-reassemblies qfp-ipucast - IPV4_VFR-4-INVALID_DROP_LOG_TYPE 4-Warning Dropping [chars] from [chars]. Invalid drop log type [dec] Unsupported drop log type qfp-ipucast LOG_STD_ACTION IPV4_VFR-4-INVALID_FRAG_LENGTH 4-Warning Dropping [chars] from [chars] due to invalid fragment length. This message indicates that the router has encountered a fragment with invalid packet length qfp-ipucast "To prevent further attacks its highly recommended that an ACL " "be configured to drop any traffic from the sender" IPV4_VFR-4-OVERLAP_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to overlap fragment. This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment. qfp-ipucast "This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender" IPV4_VFR-4-TIMEOUT 4-Warning Dropping [chars] from [chars] due to virtual reassembly timeout. This message indicates that the router is trying to do virtual-reassembly for fragments but got timeout before receiving all the fragments for a datagram qfp-ipucast "This is an informational message" IPV4_VFR-4-TINY_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to tiny fragment. This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header qfp-ipucast "This is an informational message" IPV4_VFR-4-TOO_MANY_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to too many fragments for the datagram. This message indicates the datagram being reassembled has received more fragments than its threshold value qfp-ipucast "Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ip virtual-reassembly max-fragments " IPV4MCAST-3-MCAST_CFG_ERR 3-Error [chars] Processing MCAST packet failed due to incorrect config to HW Data structures. cpp-ucode LOG_STD_ACTION IPV4MCAST-3-MCAST_MLRE_ERR 3-Error Non MLRE friendly FIA on interface [chars] Unexpected flowlock id following feature execution cpp-ucode LOG_STD_ACTION IPV4MCAST-3-MCAST_PA_REPLICATE_FAILED 3-Error [chars] m-cast replication failure for PA described packet. cpp-ucode LOG_STD_ACTION IPV4MCAST-3-MCAST_REPLICATE_GATHER_FAILED 3-Error [chars] [inet] m-cast replication failure due to a bad Multicast Gather parameter. cpp-ucode LOG_STD_ACTION IPV4MCAST-3-SANITY_CHECK_FAILED 3-Error PIM register from [inet] for [inet] [inet] - - - IPV6_ADDRESS-3-ADDRESS_CFG 3-Error %P/[dec] can not be configured on [chars] [chars] An error was encountered while configuring an IPv6 address ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-ADDRESS_CFG 3-Error %P/[dec] can not be configured on [chars] [chars] An error was encountered while configuring an IPv6 address ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-NO_UNIQUE_IDENTIFIER 3-Error Cannot determine an unique IPv6 identifier for the system. IPv6 will not be started. An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_ADDRESS-3-NO_UNIQUE_IDENTIFIER 3-Error Cannot determine an unique IPv6 identifier for the system. IPv6 will not be started. An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_ADDRESS-3-NULLIDB 3-Error Uninitialized interface pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-NULLIDB 3-Error Uninitialized interface pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-OPINPROGRESS 3-Error Operation in progress - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-OPINPROGRESS 3-Error Operation in progress - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-RESERVED_INTFID 3-Error Removing %P from [chars] - contains reserved interface identifier. [chars] Removing IPv6 global address contains the reserved interface identifier ipv6 LOG_STD_ACTION IPV6_ADDRESS-3-RESERVED_INTFID 3-Error Removing %P from [chars] - contains reserved interface identifier. [chars] An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_ADDRMGR-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ADDRMGR-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_FORWARDING-2-CAUSE_THROTTLE_ERR 2-Critical Allocation of ipv6 throttle [chars] memory failed Allocation of memory resource use by ipv6 throttle fail cpp-ucode LOG_STD_ACTION IPV6_FORWARDING-3-CAUSE_LINKTYPE_ERR 3-Error Unsupported link type [chars] dropping packet Link type is unsupported at the current time. cpp-ucode LOG_STD_ACTION IPV6_FORWARDING-3-NULLIDB 3-Error Uninitialized interface pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_FORWARDING-3-NULLIDB 3-Error Uninitialized interface pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_FORWARDING-3-NULLPAK 3-Error Uninitialized buffer pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_FORWARDING-3-NULLPAK 3-Error Uninitialized buffer pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_FORWARDING-3-TABLE_ID_SZ_ERR 3-Error Table ID size configured incorrectly: [dec] Table ID size must be less than or equal to 16 or 32 bits. cpp-ucode LOG_STD_ACTION IPV6_FORWARDING-3-UNFRAGMENTABLE 3-Error Cannot fragment packet: unfragmentable part length [dec] MTU of [dec] An internal software error occurred. A single packet originated by this system could not be fragmented and has been dropped. Normal system operation continues. ipv6 - IPV6_FORWARDING-3-UNFRAGMENTABLE 3-Error Cannot fragment packet: unfragmentable part length [dec] MTU of [dec] An internal software error occurred. A single packet originated by this system could not be fragmented and has been dropped. Normal system operation continues. ipv6 - IPV6_FORWARDING-4-CHECKSUM_ERR 4-Warning Checksum buffer walk failed Internal problem occured during calculating segmented packet checksum. cpp-ucode LOG_STD_ACTION IPV6_FORWARDING-4-MULTICAST 4-Warning Application does not support multicast destination address %P packet dropped. - - - IPV6_FORWARDING-4-MULTICAST 4-Warning Application does not support multicast destination address %P packet dropped. - - - IPV6_ICMP-3-NULLPAK 3-Error Uninitialized buffer pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ICMP-3-NULLPAK 3-Error Uninitialized buffer pointer - [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_INTF-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_INTF-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_INTF-3-MIN_MTU 3-Error The link MTU of [chars] is below the [dec]-byte minimum IPv6 link MTU. As specified in the standard IPv6 requires that every link has an MTU of at least 1280. Since this link's MTU is below that IPv6 is held down on this interface. ipv6 LOG_STD_NO_ACTION IPV6_INTF-3-MIN_MTU 3-Error The link MTU of [chars] is below the [dec]-byte minimum IPv6 link MTU. As specified in the standard IPv6 requires that every link has an MTU of at least 1280. Since this link's MTU is below that IPv6 is held down on this interface. ipv6 LOG_STD_NO_ACTION IPV6_INTF-3-NO_PROCESS 3-Error Cannot start IPv6 Interface Process. The IPv6 Interface Process could not be started. Interfaces will not be enabed for IPv6 Processing. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_INTF-3-NO_PROCESS 3-Error Cannot start IPv6 Interface Process. The IPv6 Interface Process could not be started. Interfaces will not be enabed for IPv6 Processing. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_INTF-3-SET_MTU 3-Error The link MTU of [chars] is below the [dec]-byte user set IPv6 link MTU. The interface link MTU is below the user set IPv6 link MTU. IPv6 is held down on this interface. ipv6 LOG_STD_NO_ACTION IPV6_INTF-3-SET_MTU 3-Error The link MTU of [chars] is below the [dec]-byte user set IPv6 link MTU. The interface link MTU is below the user set IPv6 link MTU. IPv6 is held down on this interface. ipv6 LOG_STD_NO_ACTION IPV6_INTF-4-L2_MISMATCH 4-Warning High load on interface events [chars] auto-recovery complete. - - - IPV6_INTF-4-L2_MISMATCH 4-Warning High load on interface events [chars] auto-recovery complete. - - - IPV6_ND-3-CONFLICT 3-Error Router %P on [chars] conflicting ND setting [chars] Another router on the link sent router advertisements\n\ with conflicting parameters to ours. ipv6 "Verify that all IPv6 routers on the link have the same parameters\n\ in the router advertisement for hop-limit managed-config-flag\n\ other-config-flag reachable-time and ns-interval and that\n\ preferred and valid lifetimes for the same prefix advertised\n\ by several routers are the same. Use the command show ipv6 interface\n\ to list the parameters per interface." IPV6_ND-3-CONFLICT 3-Error Router %P on [chars] conflicting ND setting [chars] Another router on the link sent router advertisements\n\ with conflicting parameters to ours. ipv6 "Verify that all IPv6 routers on the link have the same parameters\n\ in the router advertisement for hop-limit managed-config-flag\n\ other-config-flag reachable-time and ns-interval and that\n\ preferred and valid lifetimes for the same prefix advertised\n\ by several routers are the same. Use the command show ipv6 interface\n\ to list the parameters per interface." IPV6_ND-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6_nd LOG_STD_ACTION IPV6_ND-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6_nd LOG_STD_ACTION IPV6_ND-3-IPV6PAKENCAP 3-Error Dest host is IPv4 in IPv6 packet - [chars] IPv6 packet encapsulation called with IPv4 destination host ipv6 "Use an IPv6 address in neighbour for IPv6 packet flow on the router" "if the problem persists or you feel this should be supported then " "please contact the TAC with the failing command line." IPV6_ND-3-IPV6PAKENCAP 3-Error Dest host is IPv4 in IPv6 packet - [chars] IPv6 packet encapsulation called with IPv4 destination host ipv6 "Use an IPv6 address in neighbour for IPv6 packet flow on the router" "if the problem persists or you feel this should be supported then " "please contact the TAC with the failing command line." IPV6_ND-3-ND_ROUTER_NUM 3-Error Router list not empty [dec]. Recounting routers autocorrecting There is a missmatch between the number of routers known to ND and\n\ the number of routers known to the interface. The issue will\n\ auto-correct itself ipv6 NOG_STD_NO_ACTION IPV6_ND-3-ND_ROUTER_NUM 3-Error Router list not empty [dec]. Recounting routers autocorrecting There is a missmatch between the number of routers known to ND and\n\ the number of routers known to the interface. The issue will\n\ auto-correct itself ipv6 NOG_STD_NO_ACTION IPV6_ND-3-NULLDATA 3-Error Uninitialized data - [chars] An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_ND-3-NULLDATA 3-Error Uninitialized data - [chars] An IPv6 process could not be started. This machine will not be able to process any IPv6 packets. ipv6 "Reduce other system activity to ease memory demands. If conditions " "warrant upgrade to a larger memory configuration." IPV6_ND-4-DUPLICATE 4-Warning Duplicate address %P on [chars] Another system is using your IPv6 address. ipv6 "Change the IPv6 address of one of the " "two systems." IPV6_ND-4-DUPLICATE 4-Warning Duplicate address %P on [chars] Another system is using your IPv6 address. ipv6 "Change the IPv6 address of one of the " "two systems." IPV6_ND-4-DUPLICATE_OPTIMISTIC 4-Warning Duplicate address %P on [chars] You have elected not to run DAD but another system is using your IPv6 address. ipv6 "Change the IPv6 address of one of the " "two systems." IPV6_ND-4-DUPLICATE_OPTIMISTIC 4-Warning Duplicate address %P on [chars] You have elected not to run DAD but another system is using your IPv6 address. ipv6 "Change the IPv6 address of one of the " "two systems." IPV6_ND-4-DUPOLPFX 4-Warning Prefix %P/[dec] advertised in RA on [chars] was previously learnt on another interface This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been learnt from an RA on another interface. The prefix will be ignored on the current interface ipv6_nd " Learning the same on-link prefix via IPv6 ND RA" " on multiple interfaces indicates a likely" " configuration error on adjacent routers." " Review network topology and adjacent router" " configuration and correct as appropriate" IPV6_ND-4-DUPOLPFX 4-Warning Prefix %P/[dec] advertised in RA on [chars] was previously learnt on another interface This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been learnt from an RA on another interface. The prefix will be ignored on the current interface ipv6_nd " Learning the same on-link prefix via IPv6 ND RA" " on multiple interfaces indicates a likely" " configuration error on adjacent routers." " Review network topology and adjacent router" " configuration and correct as appropriate" IPV6_ND-4-INTFLIMIT 4-Warning Attempt to exceed interface limit on [chars] for %P An ND resolution request was received on the specified interface for the specified destination. Satisfying the request would have exceeded the ND cache entry limit configured on the interface. The request was ignored ipv6 "No action is necessary. Review the interface" " ND cache entry limit configured via" " ipv6 nd cache interface-limit if appropriate" IPV6_ND-4-INTFLIMIT 4-Warning Attempt to exceed interface limit on [chars] for %P An ND resolution request was received on the specified interface for the specified destination. Satisfying the request would have exceeded the ND cache entry limit configured on the interface. The request was ignored ipv6 "No action is necessary. Review the interface" " ND cache entry limit configured via" " ipv6 nd cache interface-limit if appropriate" IPV6_ND-4-LLA_CONFLICT 4-Warning LLA conflict for static neighbor %P on [chars] : [chars] This error indicates that an ND message from the specified neighbor carries a Link Layer Address other than that configured via static neighbor ipv6 "Reconfigure the static neighbor with correct LLA" IPV6_ND-4-LLA_CONFLICT 4-Warning LLA conflict for static neighbor %P on [chars] : [chars] This error indicates that an ND message from the specified neighbor carries a Link Layer Address other than that configured via static neighbor ipv6 "Reconfigure the static neighbor with correct LLA" IPV6_ND-4-LOOPBACK 4-Warning Looped back NSDAD packet detected for %P on [chars] A looped back DAD NS packet was detected for %P on [chars] ipv6 "A neighbor solicitation packet was received for an " "address on which this router is performing duplicate " "address detection. The packet was ignored because it " "originated from this router and was looped back." IPV6_ND-4-LOOPBACK 4-Warning Looped back NSDAD packet detected for %P on [chars] A looped back DAD NS packet was detected for %P on [chars] ipv6 "A neighbor solicitation packet was received for an " "address on which this router is performing duplicate " "address detection. The packet was ignored because it " "originated from this router and was looped back." IPV6_ND-4-OLPFXCON 4-Warning Prefix %P/[dec] advertised in RA on [chars] has been previously configured on another interface This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been configured on another interface. The prefix will be ignored on the current prefix ipv6_nd " Learning an on-link prefix via IPv6 ND RA" " when the same prefix has previously been" " configured on another interface indicates a" " likely configuration error either on the" " current router or on the neighbor router" " advertising the ND RA. Review network topology" " current router and adjacent router configuration" " and correct as appropriate" IPV6_ND-4-OLPFXCON 4-Warning Prefix %P/[dec] advertised in RA on [chars] has been previously configured on another interface This warning indicates that an on-link prefix advertised in an IPv6 ND RA on the specified interface has previously been configured on another interface. The prefix will be ignored on the current prefix ipv6_nd " Learning an on-link prefix via IPv6 ND RA" " when the same prefix has previously been" " configured on another interface indicates a" " likely configuration error either on the" " current router or on the neighbor router" " advertising the ND RA. Review network topology" " current router and adjacent router configuration" " and correct as appropriate" IPV6_ND-4-RA_TIMERS_INCONSISTENT 4-Warning Configured Router Advertisements interval exceeds the configured RA lifetime on [chars]. This warning indicates that the value configured for the Router Advertisements interval exceeds the value configured for Router Advertisements lifetime on the given interface. This is not recommended as it will lead to hosts timing out the router between Router Advertisement transmissions. ipv6_nd " Check the router configuration on the interface" " and correct it so that RA lifetime is greater" " than RA interval." IPV6_ND-4-RA_TIMERS_INCONSISTENT 4-Warning Configured Router Advertisements interval exceeds the configured RA lifetime on [chars]. This warning indicates that the value configured for the Router Advertisements interval exceeds the value configured for Router Advertisements lifetime on the given interface. This is not recommended as it will lead to hosts timing out the router between Router Advertisement transmissions. ipv6_nd " Check the router configuration on the interface" " and correct it so that RA lifetime is greater" " than RA interval." IPV6_ND-4-RESOURCE_LIMIT 4-Warning [chars] resource limit prevents creation of ND entry This warning indicates that an ND cache entry could not be created because the indicated platform resource limit has been reached. ipv6_nd "Check the size of the ND cache table. " "Consider using ND cache sizing to explicitly " "configure the size of the ND cache on each " "interface" IPV6_ND-4-RESOURCE_LIMIT 4-Warning [chars] resource limit prevents creation of ND entry This warning indicates that an ND cache entry could not be created because the indicated platform resource limit has been reached. ipv6_nd "Check the size of the ND cache table. " "Consider using ND cache sizing to explicitly " "configure the size of the ND cache on each " "interface" IPV6_ND-4-RSRV_ADDRESS 4-Warning [chars]: [chars]: [chars] IPv6 address contains reserved interface identifiers. ipv6 NOG_STD_NO_ACTION IPV6_ND-4-RSRV_ADDRESS 4-Warning [chars]: [chars]: [chars] IPv6 address contains reserved interface identifiers. ipv6 NOG_STD_NO_ACTION IPV6_ND-6-ADDRESS 6-Information %P/[dec] can not generate auto-configured address on [chars] [chars][chars] IPv6 address could not be auto-configured. ipv6 NOG_STD_NO_ACTION IPV6_ND-6-ADDRESS 6-Information %P/[dec] can not generate auto-configured address on [chars] [chars][chars] IPv6 address could not be auto-configured. ipv6 NOG_STD_NO_ACTION IPV6_ND-6-DUPLICATE_INFO 6-Information DAD attempt detected for %P on [chars] Another system attempted to configure an IPv6 address already configured on this interface. The configuration of the other system was denied. ipv6 "No action is required on this system." IPV6_ND-6-DUPLICATE_INFO 6-Information DAD attempt detected for %P on [chars] Another system attempted to configure an IPv6 address already configured on this interface. The configuration of the other system was denied. ipv6 "No action is required on this system." IPV6_POLICY_API-4-IPV6_LOCALPOLICYOVERIDE 4-Warning Local dynamic policy overriding static local policy Static policy and dynamic local policy are configured. The dynamic local policy will override the static local policy. ipv6 "Remove the static local policy config if desired." IPV6_POLICY_API-4-IPV6_POLICYOVERIDE 4-Warning Dynamic policy overriding static on intf:[chars] Static policy and dynamic policy are configured on the interface. The dynamic policy will override the static policy. ipv6 "Remove the static policy config if desired." IPV6_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_EXTEND_FAILED 3-Error - Increasing of fragment information pool failed. cpp-ucode LOG_STD_ACTION IPV6_REASS_PROXY-3-PROXY_IPC_FRAG_INFO_MEM_INIT_FAILED 3-Error - Initialization of fragment information pool failed. cpp-ucode LOG_STD_ACTION IPV6_REASS_PROXY-3-PROXY_IPC_INIT_FAILED 3-Error [dec] IPC handler initialization failed. cpp-ucode LOG_STD_ACTION IPV6_REASS_PROXY-4-PROXY_IPC_INVALID_MSG 4-Warning [hec] Received an invalid IPC messages subtype. cpp-ucode LOG_STD_ACTION IPV6_RIP-3-ALLOC_ERR 3-Error Memory allocation problem - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-ALLOC_ERR 3-Error Memory allocation problem - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-ALLOC_IPDB 3-Error Can't alloc iPDB structure - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-ALLOC_IPDB 3-Error Can't alloc iPDB structure - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-ALLOC_PDB 3-Error Can't alloc PDB structure - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-ALLOC_PDB 3-Error Can't alloc PDB structure - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLIDB 3-Error Uninitialized interface pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLIDB 3-Error Uninitialized interface pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLIPDB 3-Error Uninitialized iPDB pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLIPDB 3-Error Uninitialized iPDB pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPAK 3-Error Uninitialized packet pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPAK 3-Error Uninitialized packet pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPDB 3-Error Uninitialized PDB pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPDB 3-Error Uninitialized PDB pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPROTO 3-Error Uninitialized protocol pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLPROTO 3-Error Uninitialized protocol pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLSOC 3-Error Uninitialized socket pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-NULLSOC 3-Error Uninitialized socket pointer - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-PROCESS_CREATE 3-Error Can't create process - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-PROCESS_CREATE 3-Error Can't create process - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-PROCESS_MSG_SEND 3-Error Can't send message to process - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_RIP-3-PROCESS_MSG_SEND 3-Error Can't send message to process - RIPv6 An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ROUTING-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ROUTING-3-INTERNAL 3-Error Internal error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ROUTING-3-RIB 3-Error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ROUTING-3-RIB 3-Error [chars] An internal software error occurred. ipv6 LOG_STD_ACTION IPV6_ROUTING-3-ROUTELIMITEXCEEDED 3-Error IPv6 routing table limit exceeded - [chars] The number of routes in the named IPv6 routing table has reached the configured limit. No further routes will be added to the table ipv6 "Reduce the number of routes in the table or reconfigure the limit" IPV6_ROUTING-3-ROUTELIMITEXCEEDED 3-Error IPv6 routing table limit exceeded - [chars] The number of routes in the named IPv6 routing table has reached the configured limit. No further routes will be added to the table ipv6 "Reduce the number of routes in the table or reconfigure the limit" IPV6_ROUTING-3-ROUTELIMITWARNING 3-Error IPv6 routing table limit warning - [chars] The number of routes in the named IPv6 routing table has reached the configured warning limit. ipv6 "Reduce the number of routes in the table or reconfigure the limit" IPV6_ROUTING-3-ROUTELIMITWARNING 3-Error IPv6 routing table limit warning - [chars] The number of routes in the named IPv6 routing table has reached the configured warning limit. ipv6 "Reduce the number of routes in the table or reconfigure the limit" IPV6_ROUTING-4-MAXPDB 4-Warning Exceeded maximum supported IPv6 Routing Protocol instances This error indicates that configuration of a Routing Protocol has failed because it would exceed the maximum supported number of Routing Protocols ipv6 "Reduce the number of IPv6 Routing Protocol" " instances configured" IPV6_ROUTING-4-MAXPDB 4-Warning Exceeded maximum supported IPv6 Routing Protocol instances This error indicates that configuration of a Routing Protocol has failed because it would exceed the maximum supported number of Routing Protocols ipv6 "Reduce the number of IPv6 Routing Protocol" " instances configured" IPV6_ROUTING-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPV6_ROUTING-4-REDIST_MAX_PFX 4-Warning Redistribution prefix limit has been reached \[chars]\ - [dec] prefixes We have reached the maximum number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPV6_ROUTING-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPV6_ROUTING-4-REDIST_THR_PFX 4-Warning Redistribution prefix threshold has been reached \[chars]\ - [dec] prefixes We have reached the threshold level of number of redistributed prefixes - "Check if redistribution of large number of prefixes is " "desired and has not been configured by mistake" IPV6_ROUTING-6-ROUTELIMITRECOVERED 6-Information IPv6 routing table limit recovered - [chars] The number of routes in the named IPv6 routing table has fallen below the configured limit. The routing table has recovered ipv6 LOG_STD_NO_ACTION IPV6_ROUTING-6-ROUTELIMITRECOVERED 6-Information IPv6 routing table limit recovered - [chars] The number of routes in the named IPv6 routing table has fallen below the configured limit. The routing table has recovered ipv6 LOG_STD_NO_ACTION IPV6_URPF-4-DROP 4-Warning Dropping [chars] from [chars]. This message indicates that the router dropped a packet due to Unicast Reverse Path Forwarding check failure qfp-ipucast "This is an informational message" IPV6_VFR-4-CONFIG 4-Warning Dropping [chars] from [chars] due to system config. This message indicates that the router drops fragment packet due to ipv6 virtual-reassembly drop-fragments qfp-ipucast "This is an informational message" IPV6_VFR-4-FRAG_TABLE_OVERFLOW 4-Warning Dropping [chars] from [chars] due to fragment table overflow. This means the number of datagrams reassembled at a time reached its maximum limit increase the value of max-reassemblies using ipv6 virtual-reassembly in/out max-reassemblies qfp-ipucast - IPV6_VFR-4-INVALID_DROP_LOG_TYPE 4-Warning Dropping [chars] from [chars]. Invalid drop log type [dec] Unsupported drop log type qfp-ipucast LOG_STD_ACTION IPV6_VFR-4-INVALID_FRAG_LENGTH 4-Warning Dropping [chars] from [chars] due to invalid fragment length. This message indicates that the router has encountered a fragment with invalid packet length qfp-ipucast "To prevent further attacks its highly recommended that an ACL " "be configured to drop any traffic from the sender" IPV6_VFR-4-OVERLAP_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to overlap fragment. This message is logged whenever the router encounters overlap fragments. Overlap fragment means offset of one fragment overlaps the offset of another fragment. For example if first fragment's offset is 0 and length is 800 then the second fragments offset must be 800. If second fragment's offset is less than 800 that means the second fragment overlaps the first fragment. qfp-ipucast "This could possibly be an attack configure a static ACL to prevent " "further overlap fragments from the sender" IPV6_VFR-4-TIMEOUT 4-Warning Dropping [chars] from [chars] due to virtual reassembly timeout. This message indicates that the router is trying to do virtual-reassembly for fragments but got timeout before receiving all the fragments for a datagram qfp-ipucast "This is an informational message" IPV6_VFR-4-TINY_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to tiny fragment. This message indicates that the router is receiving tiny fragments - meaning the initial fragment does not have complete layer 4 header qfp-ipucast "This is an informational message" IPV6_VFR-4-TOO_MANY_FRAGMENTS 4-Warning Dropping [chars] from [chars] due to too many fragments for the datagram. This message indicates the datagram being reassembled has received more fragments than its threshold value qfp-ipucast "Check if the fragments received are from a genuine source if so " "increase the value of max-fragments using the CLI " "ipv6 virtual-reassembly in/out max-fragments " IPV6FIB-3-GLOBALSTATE 3-Error Inconsistent global state '[chars]' [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-3-GLOBALSTATE 3-Error Inconsistent global state '[chars]' [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBCBLK 4-Warning Missing cef table for tableid %lu during [chars] event IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBCBLK 4-Warning Missing cef table for tableid %lu during [chars] event IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBIDB 4-Warning Missing cef idb for [chars] during [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBIDB 4-Warning Missing cef idb for [chars] during [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBXDRINV 4-Warning Invalid format. [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBXDRINV 4-Warning Invalid format. [chars] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBXDRLEN 4-Warning Invalid XDR length. Type/event [dec]/[chars]. XDR [dec] buffer [dec] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6FIB-4-FIBXDRLEN 4-Warning Invalid XDR length. Type/event [dec]/[chars]. XDR [dec] buffer [dec] IPV6FIB_INTERNAL_ERROR IPV6FIB_DDTS_COMPONENT LOG_STD_ACTION IPV6MCAST-3-MCAST_CFG_ERR 3-Error [chars] Processing MCAST packet failed due to incorrect config to HW Data structures. cpp-ucode LOG_STD_ACTION IPV6MCAST-3-MCAST_ERR 3-Error [chars] 0x[hec] 0x[hec] 0x[hec] 0x[hec] A Mcast replica error has occurred cpp-ucode LOG_STD_ACTION IPV6MCAST-3-SANITY_CHECK_FAILED 3-Error PIM register from [inet] for [inet] [inet] - - - IPX-2-RADIXINIT 2-Critical Error Initializing novell path structure A programming error has occured novell "Please ensure that sufficient memory required to load this " "image is available in this device. If memory requirements " "are met then follow the succeeding procedure. " LOG_STD_SH_TECH_ACTION IPX-2-RADIXINIT 2-Critical Error Initializing novell path structure A programming error has occured novell "Please ensure that sufficient memory required to load this " "image is available in this device. If memory requirements " "are met then follow the succeeding procedure. " LOG_STD_SH_TECH_ACTION IPX-3-BADCOUNT 3-Error Bad IPX server count. [chars] [dec] [chars] [dec] The internal SAP service count does not match the number of services\n\currently present and displayed by the show ipx servers command. novell "If this message recurs report the problem to your\n\technical support representative along with the output of the show\n\ipx servers command taken before the message appeared and again after\n\ the message appeared." IPX-3-BADCOUNT 3-Error Bad IPX server count. [chars] [dec] [chars] [dec] The internal SAP service count does not match the number of services\n\currently present and displayed by the show ipx servers command. novell "If this message recurs report the problem to your\n\technical support representative along with the output of the show\n\ipx servers command taken before the message appeared and again after\n\ the message appeared." IPX-3-BADHASHTABLE 3-Error Consistency check failed for SAP table [dec]. An internal SAP table consistency check failed. novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IPX-3-BADHASHTABLE 3-Error Consistency check failed for SAP table [dec]. An internal SAP table consistency check failed. novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative." IPX-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." IPX-3-BADIGRPSAP 3-Error Cannot send incremental SAP update to peer on [chars].\n \tIncreasing output-sap-delay may help An incremental SAP update could not be sent because this might cause\n\ the SAP tables between peers to become out of synch. novell "Increase the output SAP delay on the listed interface to reduce\n\ buffer usage. If after changing the delay the message remains\n\ copy the error message exactly as it appears and report it to your\n\ technical support representative." IPX-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." IPX-3-BADIGRPSAPTYPE 3-Error Unsupported SAP type for EIGRP being [chars] - type [hec] - novell "Copy the error message exactly as it appears and report it to your\n\ technical support representative. If possible also provide the output\n\ of the debug ipx sap activity and debug ipx sap event commands for the\n\ period during which this message appeared." IPX-3-BADINSERT 3-Error Duplicate SAP entry insert attempted. [chars][chars] [chars]0x[hec] [chars]0x[hec] [chars][dec] [chars]0x[hec] [chars]0x[hec] [chars]0x[hec] An IPX SAP service entry which is being added currently already exists in\n\the current internal table. novell "Report the error messages and the tracebacks following them to your technical\n\support representative." IPX-3-BADINSERT 3-Error Duplicate SAP entry insert attempted. [chars][chars] [chars]0x[hec] [chars]0x[hec] [chars][dec] [chars]0x[hec] [chars]0x[hec] [chars]0x[hec] An IPX SAP service entry which is being added currently already exists in\n\the current internal table. novell "Report the error messages and the tracebacks following them to your technical\n\support representative." IPX-3-BADPATHS 3-Error Invalid number of paths [dec] for %q An internal inconsistency was detected in the IPX routing table\n\ structure. novell - IPX-3-BADPATHS 3-Error Invalid number of paths [dec] for %q An internal inconsistency was detected in the IPX routing table\n\ structure. novell - IPX-3-BADRDBDATA 3-Error Inconsistency in the [chars] LSP Linkage data structure detected. An internal inconsistency was detected in the RDB or SRDB\n\ internal routing table structure. Specifically a data area used by\n\ NLSP to link LSPs. novell "Copy and save this message. If NLSP is not running this could mean\n\ there is a software or hardware problem which is corrupting memory.\n\ If the message recurs copy and save the messages and call your\n\ technical support representative for assistance." IPX-3-BADRDBDATA 3-Error Inconsistency in the [chars] LSP Linkage data structure detected. An internal inconsistency was detected in the RDB or SRDB\n\ internal routing table structure. Specifically a data area used by\n\ NLSP to link LSPs. novell "Copy and save this message. If NLSP is not running this could mean\n\ there is a software or hardware problem which is corrupting memory.\n\ If the message recurs copy and save the messages and call your\n\ technical support representative for assistance." IPX-3-NOVNOSTART 3-Error IPX Failed to Start due to insufficient memory The Novell IPX routing subsystem failed to initialize properly\n\ due to memory allocation errors usually due to insufficient\n\ amount of available memory. novell "Free up memory look for a possible memory leak or upgrade the\n\ system to have more memory." IPX-3-NOVNOSTART 3-Error IPX Failed to Start due to insufficient memory The Novell IPX routing subsystem failed to initialize properly\n\ due to memory allocation errors usually due to insufficient\n\ amount of available memory. novell "Free up memory look for a possible memory leak or upgrade the\n\ system to have more memory." IPX-3-TOOMANYNETS 3-Error Too many networks. The number of directly connected IPX networks cannot exceed [dec] The limit of connected IPX networks has been reached.\n\ Additional IPX interfaces cannot be configured. novell "Do not configure IPX on additional interfaces. \n\ Remove IPX configuration commands from inactive interfaces." IPX-3-TOOMANYNETS 3-Error Too many networks. The number of directly connected IPX networks cannot exceed [dec] The limit of connected IPX networks has been reached.\n\ Additional IPX interfaces cannot be configured. novell "Do not configure IPX on additional interfaces. \n\ Remove IPX configuration commands from inactive interfaces." IPX-6-NOVACCESSLOG 6-Information [chars] [chars] [chars] [chars] [hec].[enet] [chars] [hec].[enet] [dec] pkt[chars] If IPX access violation logging is enabled these messages are\n\ displayed when an access list logging event has occurred. novell "Verify that the host system is permitted or denied as defined in the\n\ access list." IPX-6-NOVACCESSLOG 6-Information [chars] [chars] [chars] [chars] [hec].[enet] [chars] [hec].[enet] [dec] pkt[chars] If IPX access violation logging is enabled these messages are\n\ displayed when an access list logging event has occurred. novell "Verify that the host system is permitted or denied as defined in the\n\ access list." IPX-7-DEBUGMSG 7-Debug [chars]: %08x %08x %08x %08x %08x Internal use only novell "Should not be seen in the field" IPX-7-DEBUGMSG 7-Debug [chars]: %08x %08x %08x %08x %08x Internal use only novell "Should not be seen in the field" IR8340_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_ASSERT 0-Emergency External alarm/digital IO port [chars] asserted\n External alarm/digital IO port alert is detected - "No action recommended" LOG_STD_ACTION IR8340_ALARM_CONTACT-0-EXTERNAL_ALARM_CONTACT_CLEAR 0-Emergency External alarm/digital IO port [chars] cleared\n External alarm/digital IO port alert is cleared - "No action recommended" LOG_STD_ACTION IRECAGENTSERVER-3-NOINIT 3-Error Can't initialize iREC agent server Internal problems with initializing ports for the iREC agent\n\server ios-callmgr "Make sure the iREC agent server port is available on the local\n\machine." IRECAGENTSERVER-3-NOINIT 3-Error Can't initialize iREC agent server Internal problems with initializing ports for the iREC agent\n\server ios-callmgr "Make sure the iREC agent server port is available on the local\n\machine." IRECAGENTSERVER-3-NOMEM 3-Error Can't initialize memory for iREC agent server Insufficient Memory for iREC agent server ios-callmgr "Increase amount of available memory" IRECAGENTSERVER-3-NOMEM 3-Error Can't initialize memory for iREC agent server Insufficient Memory for iREC agent server ios-callmgr "Increase amount of available memory" IRECAGENTSERVER-3-NOPROC 3-Error Could not start iREC agent Server Internal Problem in process creation ios-callmgr "None" IRECAGENTSERVER-3-NOPROC 3-Error Could not start iREC agent Server Internal Problem in process creation ios-callmgr "None" IRECAGENTSERVER-3-NOSOCKETS 3-Error Max Number of iREC agent Server sockets exceeded There are too many iREC agent clients requesting service ios-callmgr "Reduce number of iREC agent requesting service" IRECAGENTSERVER-3-NOSOCKETS 3-Error Max Number of iREC agent Server sockets exceeded There are too many iREC agent clients requesting service ios-callmgr "Reduce number of iREC agent requesting service" ISDN-1-NOMEMORY 1-Alert no memory for [chars] The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." ISDN-2-ISDN_EXIT 2-Critical [chars] The ISDN task has terminated execution for the specified reason and may cause CISCO IOS to terminate. - LOG_STD_ACTION ISDN-2-ISDN_FATAL 2-Critical ISDN FATAL ERROR: file [chars] function [chars] message: [chars] ISDN has detected a fatal system error. - LOG_STD_ACTION ISDN-2-ISDN_GENERAL_TRACEBACK 2-Critical [chars]:[dec] A debug - traceback condition has occurred - LOG_STD_NO_ACTION ISDN-3-ISDN_CCB_FREE 3-Error [chars]: CCB with call id 0x%04X on b channel [dec] was leaked but has been freed by ISDN Housekeeping. Reason: [chars] A data structure internal to ISDN has leaked. isdn LOG_STD_NO_ACTION ISDN-3-ISDN_CCB_FREE_FAILS 3-Error [chars]: CCB with call id 0x%04X on b channel [dec] was leaked reason: [chars] and can't be free'd by ISDN Housekeeping. A data structure internal to ISDN has leaked and we can't fix it for some reason. isdn LOG_STD_NO_ACTION ISDN-3-ISDN_NLCB_FREE 3-Error [chars]: NLCB with call id 0x%04X was leaked but has been freed by ISDN Housekeeping. Reason: [chars] A data structure internal to ISDN has leaked. isdn LOG_STD_NO_ACTION ISDN-3-ISDN_RESOURCE_UNAVAILABLE 3-Error [chars]: Resource not available at [chars]:[dec] Hardware resource could not be allocated - LOG_STD_ACTION ISDN-3-LAYER2_DOWN 3-Error Layer 2 for Interface [chars] TEI [dec] changed to down This is an informational message but being logged as ERR at request\n\ from some customers. It is sent when an ISDN Layer2 logical link is \n\ down. It also shows the TEI associated with this logical link. - LOG_STD_NO_ACTION ISDN-3-LAYER2_UP 3-Error Layer 2 for Interface [chars] TEI [dec] changed to up This is an informational message but being logged as an ERR at request\n\ from some customers. It is sent when an ISDN Layer2 logical link is up.\n\ It also shows the TEI associated with this logical link. - LOG_STD_NO_ACTION ISDN-4-BAD_DSL_FOR_CREATE_DELETE_L2 4-Warning [chars]: isdn_create_delete_signalling_channel: Unknown DSL [dec] for\n\ [chars] The Creation/Deletion service for the L2 Signalling handler\n\for the given DSL is missing - LOG_STD_SH_TECH_ACTION ISDN-4-GET_STATUS_STATE_FAIL 4-Warning [chars]: isdn_get_status_state: Unknown DSL [dec] An attempt to retrieve the status of a DSL that \n\is not currently configured. - LOG_STD_SH_TECH_ACTION ISDN-4-INVALID_CALLEDNUMBER 4-Warning Interface [chars] Ignoring call LDN and Called Party Number mismatch The incoming ISDN call is ignored because the Called Party Number does\n\ not match the LDN numbers configured in the router. - "Correct the LDN in the router to match the Called Party\n\ Number delivered in the incoming setup message." ISDN-4-INVALID_EID 4-Warning Interface [chars] Ignoring call EndPoint Identifier EID mismatch The incoming ISDN call is ignored because the EID delivered in the\n\ incoming setup message cannot be matched. - "If EID is delivered in the setup message use the isdn\n\ debugs and show isdn status commands\n\ to determine the current EID values. You may need to contact\n\ the service provider." ISDN-4-INVALID_EVENT 4-Warning [chars]: Bad Event Received For Current State The State Transition for the ISDN L2 Socket Process failed. - LOG_STD_SH_TECH_ACTION ISDN-4-INVALID_SPID 4-Warning Interface [chars] Spid[dec] was rejected The SPID configured in the router has been rejected by the switch. - "Determine the correct SPID reenter the SPID and clear the\n\ BRI interface." ISDN-4-ISDN_CCB_LEAK 4-Warning [chars]: CCB with callid 0x%04X on b channel [dec] has been leaked. Reason: [chars] A data structure internal to ISDN has been leaked isdn LOG_STD_NO_ACTION ISDN-4-ISDN_L2_INTERFACE_NOT_REGISTERED 4-Warning [chars]: isdn_to_L2: Unknown DSL [dec] for command [chars] The ISDN Stack has not registered its L2 Message Handler - LOG_STD_SH_TECH_ACTION ISDN-4-ISDN_NLCB_LEAK 4-Warning [chars]: NLCB leak detected. nlcb %X call id 0x%04X reason: [chars] A data structure internal to ISDN has not been freed isdn LOG_STD_NO_ACTION ISDN-4-ISDN_UNEXPECTED_EVENT 4-Warning [chars]: Occurred at [chars]:[dec] An unexpected event of significance has occurred - LOG_STD_SH_TECH_ACTION ISDN-4-OPEN_TEMP_SOCKET_FAIL 4-Warning [chars]: Failed to Open Required Temporary Socket[chars] - - LOG_STD_SH_TECH_ACTION ISDN-4-RESTART 4-Warning Interface [chars] [chars] [chars] message with restart class of [chars] chan [dec] This is an informational message but will logged as a \n\ warning message if so configured. - "No action is required." ISDN-4-RLM_STATUS_CHANGE 4-Warning ISDN SC [chars]: Status Changed to: [chars]. ISDN has been notified by the RLM component of a \n\status change in the RLM link - LOG_STD_NO_ACTION ISDN-4-SERV_AUDIT_C1 4-Warning Interface [chars] service audit trigger condition [dec] on channel [dec] This is an informational message but will be logged as a warning message if so configured. - "No action is required." ISDN-4-SERVICE 4-Warning Interface [chars] [chars] [chars] message for chan [dec] state [chars] This is an informational message but will be logged as a \n\ warning message if so configured. - "No action is required." ISDN-4-SPURIOUS_CONNECT 4-Warning [chars]: Spurious Connection Accepted and Closed on port [dec] An unknown TCP connection was accepted and refused. - LOG_STD_SH_TECH_ACTION ISDN-4-STATUS 4-Warning Interface [chars] [chars] [chars] st 0x[hec] ev 0x[hec] cid 0x[hec] cref 0x[hec] This is an informational message but being logged as a \n\ warning message if so configured. - "No action is required." ISDN-5-SERV_AUDIT_C2 5-Notice Interface [chars] service audit trigger condition [dec] on channel [dec] This is an informational message but will be logged as a warning message if so configured. - "No action is required." ISDN-6-CALL_COLLISION 6-Information Interface [chars] Call Cid 0x[hec] Cref 0x[hec] collision on Channel [dec] in_use_cid 0x[hec] cref 0x[hec] Channel awarded to the received call This is an informational message. It is sent when a Call is\n\ received that collides with an existing call on the same channel. - "No action is required." ISDN-6-CHAN_UNAVAILABLE 6-Information Interface [chars] Requested Channel [dec] is not available This is an informational message. It is sent when the requested\n\ channel is not available. - "No action is required." ISDN-6-CONNECT 6-Information Interface [chars] is now connected to [chars] [chars] - - LOG_STD_NO_ACTION ISDN-6-DISCONNECT 6-Information Interface [chars] disconnected from [chars] [chars] call lasted [dec] seconds - - LOG_STD_NO_ACTION ISDN-6-INVALID_TIMER 6-Information [chars]: Invalid Timer Handle caller 0x[hec] handle %3d This could be an indication of low memory. It is sent when \n\ an invalid ISDN timer handle is passed on for timer operations - "capture the show isdn mem show isdn status output for possible \n\ debugging information. Reduce other system activity to ease the \n\ memory demands in the system." ISDN-6-LAYER2DOWN 6-Information Layer 2 for Interface [chars] TEI [dec] changed to down This is an informational message. It is sent when an ISDN Layer2\n\ logical link is down. It also shows the TEI associated with this\n\ logical link. - LOG_STD_NO_ACTION ISDN-6-LAYER2UP 6-Information Layer 2 for Interface [chars] TEI [dec] changed to up This is an informational message. It is sent when an ISDN Layer2\n\ logical link is up. It also shows the TEI associated with this\n\ logical link. - LOG_STD_NO_ACTION ISDN-6-NFAS_STATUS_CHANGE 6-Information [chars] [chars] [chars] [chars] The NFAS D-channel status has changed. - LOG_NO_ACTION ISDN-6-NO_TIMER 6-Information No Free Timer Entry caller 0x[hec] timers used [dec] This could be an indication of low memory. It is sent when the ISDN \n\ protocol cannot start new timers for it's operation. - "capture the show isdn mem show isdn status output for possible \n\ debugging information. Reduce other system activity to ease the \n\ memory demands in the system." ISDN-6-REPEATED_SETUP 6-Information Interface [chars] Call Cid 0x%04X Cref 0x%04X received a retransmitted setup on channel [dec] in_use_cid 0x%04X cref 0x%04X. This is an informational message sent when a duplicate SETUP message is received on a B-channel. This indicates that the rate of calls being received is momentarily greater than the rate calls can be processed. No action is required. - LOG_STD_NO_ACTION ISDN-6-SERV_AUDIT_C3 6-Information Interface [chars] service audit trigger condition [dec] on channel [dec] This is an informational message but will be logged as a warning message if so configured. - "No action is required." ISISL2-3-MCAST_EVENT_UPD_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client failed to send Multicast event [dec] [dec] update request with error [chars] - - - ISISL2-3-MCAST_EVENT_UPD_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client failed to send Multicast event [dec] [dec] update request with error [chars] - - - ISISL2-3-MCAST_RT_UPD_REP_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client receives the response of Multicast RT [chars] message with code:[dec] topoid:[dec] ISISL2 client receives the response of Multicast RT update failure ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-MCAST_RT_UPD_REP_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client receives the response of Multicast RT [chars] message with code:[dec] topoid:[dec] ISISL2 client receives the response of Multicast RT update failure ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-MCAST_RT_UPD_REQ_FAILURE 3-Error [chars]-RIBInfo[chars]: Multicast RT [dec] [chars] [chars]: Failed to send the ISISL2 client failed to send the Multicast route update request to MLMRIB ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-MCAST_RT_UPD_REQ_FAILURE 3-Error [chars]-RIBInfo[chars]: Multicast RT [dec] [chars] [chars]: Failed to send the ISISL2 client failed to send the Multicast route update request to MLMRIB ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-UNICAST_EVENT_UPD_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client failed to send Unicast event [dec] [dec] update request with error [chars] - - - ISISL2-3-UNICAST_EVENT_UPD_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client failed to send Unicast event [dec] [dec] update request with error [chars] - - - ISISL2-3-UNICAST_RT_UPD_REP_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client receives the response of Unicast RT [chars] message with code:[dec] topoid:[dec] ISISL2 client receives the response of Unicast RT update failure ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-UNICAST_RT_UPD_REP_FAILURE 3-Error [chars]-RIBInfo[chars]: [chars] client receives the response of Unicast RT [chars] message with code:[dec] topoid:[dec] ISISL2 client receives the response of Unicast RT update failure ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-UNICAST_RT_UPD_REQ_FAILURE 3-Error [chars]-RIBInfo[chars]: Unicast RT [dec] [chars]: Failed to send the ISISL2 client failed to send Unicast route update request to MLURIB ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISISL2-3-UNICAST_RT_UPD_REQ_FAILURE 3-Error [chars]-RIBInfo[chars]: Unicast RT [dec] [chars]: Failed to send the ISISL2 client failed to send Unicast route update request to MLURIB ISISL2_DDTS_COMPONENT LOG_STD_ACTION ISR_THROUGHPUT-3-CONF_FAILED 3-Error Configuration failed An error occurred when the throughput configuration was attempted. iosxe-csl - ISR_THROUGHPUT-3-EULA_NOT_ACCEPTED 3-Error The EULA has to be accepted prior to throughput configuration. Users need to accept EULA to activate the license iosxe-csl "Accept EULA for throughput license" ISR_THROUGHPUT-3-INVALID_CONFIG 3-Error An invalid throughput config: [chars] kbps was selected. The configured throughput is unknown iosxe-csl - ISR_THROUGHPUT-3-SETUP_FAILED 3-Error Throughput upgrade license set up failed An error occurred when setting up the throughput upgrade licenses. iosxe-csl - ISR_THROUGHPUT-6-CRYPTO 6-Information Crypto level has been set to [dec]00 kbps Crypto level has been set to a number iosxe-csl - ISR_THROUGHPUT-6-LEVEL 6-Information Throughput level has been set to [dec]00 kbps Throughput level has been set to a number iosxe-csl - ISR_THROUGHPUT-6-UNTHROTTLED 6-Information Crypto level is unthrottled Crypto level has been unthrottled iosxe-csl - ISR4000_RP_NGIO_ATM-3-ATM_DPIDB_ALLOC_FAIL 3-Error Failed to allocate a data plane identifier for interface [chars] for VCD [dec] The SPA driver is not able to allocate the datapath identifier for the VCD under the interface specified in the message. This indicates a software error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_DPIDB_GET_FAIL 3-Error Failed to get a data plane identifier for interface [chars] for VCD [dec] The SPA driver is not able to obtain the datapath identifier for the VCD under the interface specified in the message. This indicates a software error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_FLOWID_GET_FAIL 3-Error Failed to get a flow control identifier for interface [chars] for index [dec] The SPA driver is not able to obtain the datapath flow control identifier for the data path identifier under the interface specified in the message. This indicates a software error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_FLOWID_OUT_OF_RANGE 3-Error Flow control identifiers for interface [chars] chan lo [hec] chan hi [hec] The flow control identifier received for the interface is out of range. This indicates SPA driver is responding with out of range flow control identifier esg-io-infra LOG_STD_ACTION ISR4000_RP_NGIO_ATM-3-ATM_PER_SPA_MAX_VC_LIMIT_REACHED 3-Error total active atm vc per ATM SPA reached limitation of [dec] total number of active atm vc per ATM SPA has reached max limit - LOG_STD_ACTION ISR4000_RP_NGIO_ATM-3-ATM_SPA_AUTOVC_FAIL 3-Error [chars]: atm autovc discovery configuration failed reason: [chars] A command to configure the atm autovc discovery on an atm interface has failed - LOG_STD_ACTION ISR4000_RP_NGIO_ATM-3-ATM_SPA_VC_MAX_LIMIT_REACHED 3-Error total active atm vc reached system limitation of [dec] total number of active atm vc has reached max limit allowed on the system - LOG_STD_ACTION ISR4000_RP_NGIO_ATM-3-ATM_TXCHANL_GET_FAIL 3-Error Failed to get a valid tx_chan id for interface [chars] for VCD [dec] The SPA driver is not able to obtain the datapath tx channel identifier for the VCD under the interface specified in the message. This indicates a SPA occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_CFG_SEND_FAIL 3-Error Error in sending message to SPA on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_CON_SET_FAIL 3-Error Failed set ATM con for interface [chars] [dec]/[dec] VCD [dec] Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_CORE_GET_FAIL 3-Error Failed to get a ATM VC core info for interface [chars] VCD [dec] Could not get VC core information when get SPA VCOPEN or VCMODIRY response. This indicates a ATM information error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_DPIDX_GET_FAIL 3-Error Failed to get ATM dpidx for interface [chars] VCD [dec] Could not get VC dpidx information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_EGRESSID_UPDATE_FAIL 3-Error Failed to update ATM egress id for interface [chars] VCD [dec] egress_id [dec] Could not update VC egress id when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_ENCAP_GET_FAIL 3-Error Failed to get ATM encapsulation for interface [chars] [dec]/[dec] VCD [dec] Could not get VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_ERROR_ENCAP_TYPE 3-Error Get ATM ERROR encapsulation for interface [chars] [dec]/[dec] VCD [dec] Get a ERROR VC encapsulation information when get SPA VCOPEN or VCMODFY response This indicates ATM occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_INGRESS_ID_ALLOC_FAIL 3-Error Failed to allocate VC ingress identifier on interface [chars] for VCD [dec] ebfc_id [dec] when [chars] The ATM SHIM is not able to allocate the ingress identifier for the VCD under the interface specified in the message. This indicates a software error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-ATM_VC_SPA_SETUP_FAIL 3-Error SPA Error response on interface [chars] when [chars] for VCD [dec] ebfc_id [dec] ret_val [dec] The SPA give a error response for ATM setup or response timeout in atm vc setup message. This indicates a SPA occur error. esg-io-infra LOG_STD_NO_ACTION ISR4000_RP_NGIO_ATM-3-PROCESS_FAIL 3-Error process creation failed for [chars] The Periodic one second process creation failed. This indicates a software error. esg-io-infra LOG_STD_ACTION ISR4000_RP_NGIO_ATM-4-ATM_SPA_VC_ABOVE_WM_WARNING 4-Warning total active atm vc approaching [dec] percent of system limitation of [dec] total number of active atm vc is approaching the high water mark of sysyem limitation - LOG_STD_ACTION ISR4000_RP_NGIO_ATM-4-SETUPVC 4-Warning Interface [chars] VC [dec] setup failed reason = [dec] A command to setup a VC has failed on RP. esg-io-infra "The SPA ATM driver has detected a problem creating the internal OAM" "VC. Reload the indicated SPA card to reconfigure the internal OAM VC." "If the error messages persists copy the error message exactly as " "it appears. Next research and attempt to resolve the issue using " "the SPA hardware troubleshooting documentation as well as the tools " "and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ISR4000_RP_NGIO_ATM-4-TEARDOWNVC 4-Warning Interface [chars] VC [dec] teardown failed vc state = [dec]/[dec] A command to remove a VC config has failed on RP. esg-io-infra "The SPA ATM driver has detected a problem tearing down the internal" "OAM VC. Reload the indicated SPA card to do a clean tear down of the " "internal OAM VC. If the error messages persists copy the error " "message exactly as it appears. Next research and attempt to resolve " "the issue using the SPA hardware troubleshooting documentation as well" " as the tools and utilities provided at " "http://www.cisco.com/public/support/tac/tools.shtml. If you still " "require assistance open a case with the Technical Assistance Center " "via the Internet at " "http://www.cisco.com/cgi-bin/front.x/case_tools/caseOpen.pl or contact " "your Cisco technical support representative. Be sure to provide the " "the information you have gathered and a 'show tech-support' to " "your support representative or attach it to your case in non-zipped " "plain text format .txt." ISR4000_RP_NGIO_ATM-5-ATM_SPA_VC_BELOW_WM_NOTICE 5-Notice total active atm vc below [dec] percent of system limitation of [dec] total number of active atm vc below the high water mark of sysyem limitation esg-io-infra LOG_STD_ACTION ISR4000_RP_NGIO_ATM-5-MPVCVPSETUP 5-Notice Interface [chars] has a VC/VP [dec] configured already VC/VP [dec] cannot The SPA ATM driver supports configuring only one VC/VP under a point to multi point sub-interface. The sub-interface specified in the message already has VP/VC configured. - LOG_STD_NO_ACTION ISRHOG-2-NOMEM 2-Critical No memory available for configuring ISRHOG The ISRHOG protocol subsystem could not obtain the memory it needed. The leak may be generic or by any of the IOS processes consult the \n\ Technical Engineer. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem. "Copy the message exactly as it appears and report it your technical\n\ support representative." ISRHOG-2-NOMEM 2-Critical No memory available for configuring ISRHOG The ISRHOG protocol subsystem could not obtain the memory it needed. The leak may be generic or by any of the IOS processes consult the \n\ Technical Engineer. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem. "Copy the message exactly as it appears and report it your technical\n\ support representative." ISRHOG-4-MASK 4-Warning Process masked interrupts for more than [dec] microsecs\nProcess-Block-Time [dec] microsecs The process blocked interrupts for more than the latency threshold set\n\ for the ISRHOG tool. Determine the component from the traceback displayed in\n\ the error message. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem. "Copy the message exactly as it appears and report it your technical\n\ support representative." ISRHOG-4-MASK 4-Warning Process masked interrupts for more than [dec] microsecs\nProcess-Block-Time [dec] microsecs The process blocked interrupts for more than the latency threshold set\n\ for the ISRHOG tool. Determine the component from the traceback displayed in\n\ the error message. Use Topic to search for a similar DDTS.\n\ If you find none write a DDTS for this problem. "Copy the message exactly as it appears and report it your technical\n\ support representative." ISSU_ERROR-2-CLIENT_INCOMPATIBLE 2-Critical [chars][dec]: ISSU Client ISSU Client incompatible. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-CLIENT_INCOMPATIBLE 2-Critical [chars][dec]: ISSU Client ISSU Client incompatible. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NEGO_NOT_DONE 2-Critical [chars][dec]: ISSU Negotiation not complete Unable to complete ISSU negotiation. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NEGO_NOT_DONE 2-Critical [chars][dec]: ISSU Negotiation not complete Unable to complete ISSU negotiation. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_EP_TYPE_REG 2-Critical [chars][dec]: Client could not register endpoint type with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_EP_TYPE_REG 2-Critical [chars][dec]: Client could not register endpoint type with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_EP_TYPE_UNREG 2-Critical [chars][dec]: Client could not unregister endpoint type with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_EP_TYPE_UNREG 2-Critical [chars][dec]: Client could not unregister endpoint type with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_REG 2-Critical [chars][dec]: Failed to register with Could not register client with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_REG 2-Critical [chars][dec]: Failed to register with Could not register client with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_UNREG 2-Critical [chars][dec]: Could not unregister client with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-2-NTI_UNREG 2-Critical [chars][dec]: Could not unregister client with NTI. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAP_EXCHANGE 3-Error [chars][dec]: Capability exchange failed with error [chars] The capability exchange failed the ISSU client is unable to process the received capability ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAP_EXCHANGE 3-Error [chars][dec]: Capability exchange failed with error [chars] The capability exchange failed the ISSU client is unable to process the received capability ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAP_REG 3-Error [chars][dec]: failed to register The capabilities of the ISSU client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAP_REG 3-Error [chars][dec]: failed to register The capabilities of the ISSU client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPENTRY_REG 3-Error [chars][dec]: failed to register a capability entry [chars] The ISSU client failed to register a capability entry ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPENTRY_REG 3-Error [chars][dec]: failed to register a capability entry [chars] The ISSU client failed to register a capability entry ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPGROUP_REG 3-Error [chars][dec]: failed to register a capability group [chars] The ISSU client failed to register a capability group ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPGROUP_REG 3-Error [chars][dec]: failed to register a capability group [chars] The ISSU client failed to register a capability group ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPTYPE_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a capability type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CAPTYPE_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a capability type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CF_SEND 3-Error [chars][dec]: Client failed to send message [dec] ISSU client cannot send a negotiation message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CF_SEND 3-Error [chars][dec]: Client failed to send message [dec] ISSU client cannot send a negotiation message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CLIENT_REG 3-Error [chars][dec]: Client failed to register [chars] The ISSU Client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CLIENT_REG 3-Error [chars][dec]: Client failed to register [chars] The ISSU Client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CLIENT_REG_FAILED 3-Error [chars][dec]: Client is not The ISSU Client is not yet initialized. The negotiation for this client is not yet done. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-CLIENT_REG_FAILED 3-Error [chars][dec]: Client is not The ISSU Client is not yet initialized. The negotiation for this client is not yet done. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ENTITY_REG 3-Error [chars][dec]: failed to register The ISSU entity could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ENTITY_REG 3-Error [chars][dec]: failed to register The ISSU entity could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ENTITY_UNREG 3-Error [chars][dec]: failed to unregister The ISSU entity could not be unregistered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ENTITY_UNREG 3-Error [chars][dec]: failed to unregister The ISSU entity could not be unregistered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ICC_SEND 3-Error [chars][dec]: Client failed to send message ISSU client cannot send a negotiation message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-ICC_SEND 3-Error [chars][dec]: Client failed to send message ISSU client cannot send a negotiation message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_MTU 3-Error [chars][dec]: Client failed to get mtu for message [dec] [chars] [chars][dec]: client cannot get the MTU for a message type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_MTU 3-Error [chars][dec]: Client failed to get mtu for message [dec] [chars] [chars][dec]: client cannot get the MTU for a message type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_NOT_OK 3-Error [chars][dec]: ISSU message type [dec] is not compatible ISSU received a message not compatible with the running version. ISSU_CLIENT_COMP "show message type " ISSU_ERROR-3-MSG_NOT_OK 3-Error [chars][dec]: ISSU message type [dec] is not compatible ISSU received a message not compatible with the running version. ISSU_CLIENT_COMP "show message type " ISSU_ERROR-3-MSG_POLICY 3-Error [chars][dec]: Client failed to negotiate version for message type [dec] error [chars] ISSU client cannot negotiate message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_POLICY 3-Error [chars][dec]: Client failed to negotiate version for message type [dec] error [chars] ISSU client cannot negotiate message to a peer ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_REG 3-Error [chars][dec]: failed to register its messages [chars] Messages for the ISSU client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSG_REG 3-Error [chars][dec]: failed to register its messages [chars] Messages for the ISSU client could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSGGROUP_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a message group ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSGGROUP_REG 3-Error [chars][dec]: failed to The ISSU client failed to register a message group ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSGTYPE_REG 3-Error [chars][dec]: failed to register a message type [chars] The ISSU client failed to register a message type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MSGTYPE_REG 3-Error [chars][dec]: failed to register a message type [chars] The ISSU client failed to register a message type ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-MTU_NOT_ENOUGH 3-Error [chars][dec]: Requested buffer size [dec] is greater than the max MTU size Checkpoint buffer size requested is greater than the max MTU size checkpoint supports cat6000-ha LOG_STD_ACTION ISSU_ERROR-3-MTU_NOT_ENOUGH 3-Error [chars][dec]: Requested buffer size [dec] is greater than the max MTU size Checkpoint buffer size requested is greater than the max MTU size checkpoint supports cat6000-ha LOG_STD_ACTION ISSU_ERROR-3-NEGO_PROCESS 3-Error [chars][dec]: Cannot create process: [chars] The process to negotiate the session for the specified ISSU client cannot be created. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-NEGO_PROCESS 3-Error [chars][dec]: Cannot create process: [chars] The process to negotiate the session for the specified ISSU client cannot be created. ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-REG_ARBITRATE_CALLBACK 3-Error [chars][dec]: - ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-REG_ARBITRATE_CALLBACK 3-Error [chars][dec]: - ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-SESSION_REG 3-Error [chars][dec]: session failed to register [chars] The client's ISSU session could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-SESSION_REG 3-Error [chars][dec]: session failed to register [chars] The client's ISSU session could not be registered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-SESSION_UNREG 3-Error [chars][dec]: session [dec] The client's ISSU session could not be unregistered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-SESSION_UNREG 3-Error [chars][dec]: session [dec] The client's ISSU session could not be unregistered ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-START_NEGO_FAILED 3-Error [chars][dec]: failed to The ISSU client cannot start its negotiation ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-START_NEGO_FAILED 3-Error [chars][dec]: failed to The ISSU client cannot start its negotiation ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-TRANSFORM_FAILED 3-Error [chars][dec]: [chars] transformation failed [chars] The transformation operation for the ISSU message has failed ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-TRANSFORM_FAILED 3-Error [chars][dec]: [chars] transformation failed [chars] The transformation operation for the ISSU message has failed ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-TRANSFORM_FAILED_DETAILED 3-Error [chars][dec]: [chars] transformation failed for message [dec] endpoint [dec] [chars] The transformation operation for the ISSU message has failed ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_ERROR-3-TRANSFORM_FAILED_DETAILED 3-Error [chars][dec]: [chars] transformation failed for message [dec] endpoint [dec] [chars] The transformation operation for the ISSU message has failed ISSU_CLIENT_COMP LOG_STD_ACTION ISSU_INIT_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - ISSU_INIT_FAILED-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - ISSU_PROCESS-3-ABORT 3-Error [chars] Provides abort status information install "Observe the status message" ISSU_PROCESS-3-ABORT 3-Error [chars] Provides abort status information install "Observe the status message" ISSU_PROCESS-3-ABORTVERSION 3-Error issu abortversion: [chars] The ISSU abortversion command can be run only from the LoadVersion or RunVersion state install "Please proceed to reinitializing the ISSU process" ISSU_PROCESS-3-ABORTVERSION 3-Error issu abortversion: [chars] The ISSU abortversion command can be run only from the LoadVersion or RunVersion state install "Please proceed to reinitializing the ISSU process" ISSU_PROCESS-3-FILESYS 3-Error '[chars]' filesystem does not exist\n Verification of the filesystem failed install "The file needs to be downloaded to the flash disk" ISSU_PROCESS-3-FILESYS 3-Error '[chars]' filesystem does not exist\n Verification of the filesystem failed install "The file needs to be downloaded to the flash disk" ISSU_PROCESS-3-IMAGE 3-Error [chars] is loading the wrong image [ [chars] ] expected image [ [chars] ] Wrong image is being loaded during ISSU process. install "Check the detail state of ISSU process make sure " "the right images are loaded on Active and " "on Standby" ISSU_PROCESS-3-IMAGE 3-Error [chars] is loading the wrong image [ [chars] ] expected image [ [chars] ] Wrong image is being loaded during ISSU process. install "Check the detail state of ISSU process make sure " "the right images are loaded on Active and " "on Standby" ISSU_PROCESS-3-IPC_AGENT 3-Error [chars] [ [chars] ] The ISSU process IPC agent had an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-IPC_AGENT 3-Error [chars] [ [chars] ] The ISSU process IPC agent had an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-IPC_MSG 3-Error [chars] The ISSU process IPC MSG Queue Setup encountered an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-IPC_MSG 3-Error [chars] The ISSU process IPC MSG Queue Setup encountered an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-LOADVERSION 3-Error [chars] The ISSU commitversion command did not fulfill the necessary criteria. This can happen due to the following conditions not being met. \n1. Current ISSU state is not RunVersion \n2. Secondary Version doesn't exist on Standby \n3. Standby BOOT variable doesn't exist \n4. The new image is not the first in BOOT on Standby \n5. Active BOOT variable is not set \n6. Primary Version on Active doesn't exist \n7. New image is not the first in Active BOOT \n8. Configuration register is not 0x2102 install "Fix the error and try the command again" ISSU_PROCESS-3-LOADVERSION 3-Error [chars] The ISSU commitversion command did not fulfill the necessary criteria. This can happen due to the following conditions not being met. \n1. Current ISSU state is not RunVersion \n2. Secondary Version doesn't exist on Standby \n3. Standby BOOT variable doesn't exist \n4. The new image is not the first in BOOT on Standby \n5. Active BOOT variable is not set \n6. Primary Version on Active doesn't exist \n7. New image is not the first in Active BOOT \n8. Configuration register is not 0x2102 install "Fix the error and try the command again" ISSU_PROCESS-3-NVRAM 3-Error [chars] NVRAM variables are not set properly. install "The issu commands or the hw-module command did not " "set the variables properly." ISSU_PROCESS-3-NVRAM 3-Error [chars] NVRAM variables are not set properly. install "The issu commands or the hw-module command did not " "set the variables properly." ISSU_PROCESS-3-PARAMETERS 3-Error [chars] [chars] parameters are wrong The system could not be configured for ISSU install "Fix the error and try the command again" ISSU_PROCESS-3-PARAMETERS 3-Error [chars] [chars] parameters are wrong The system could not be configured for ISSU install "Fix the error and try the command again" ISSU_PROCESS-3-PEER 3-Error [chars] The ISSU process cannot continue with negotiation as it can't verify the peer's state.\n install "Make sure the peer is present and try again.\n" "If the problem persists send the output of " "'show issu state' and 'show version' to TAC." ISSU_PROCESS-3-PEER 3-Error [chars] The ISSU process cannot continue with negotiation as it can't verify the peer's state.\n install "Make sure the peer is present and try again.\n" "If the problem persists send the output of " "'show issu state' and 'show version' to TAC." ISSU_PROCESS-3-PRST 3-Error [chars] Persistent variables are not set properly. install "The issu commands or the hw-module command did not " "set the variables properly." ISSU_PROCESS-3-PRST 3-Error [chars] Persistent variables are not set properly. install "The issu commands or the hw-module command did not " "set the variables properly." ISSU_PROCESS-3-RF 3-Error [chars] [ [chars] ] The ISSU process RF client had an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-RF 3-Error [chars] [ [chars] ] The ISSU process RF client had an error. install "Copy the error and send it to TAC." ISSU_PROCESS-3-ROLLBACK_TIMER 3-Error [chars] The rollback timer could not be configured install "Fix the error and try the command again" ISSU_PROCESS-3-ROLLBACK_TIMER 3-Error [chars] The rollback timer could not be configured install "Fix the error and try the command again" ISSU_PROCESS-3-SYSTEM 3-Error [chars] The configuration register value should not be changed while the ISSU process is in progress install "The low order byte of the configuration register " "should be 0x02 during the upgrade process" ISSU_PROCESS-3-SYSTEM 3-Error [chars] The configuration register value should not be changed while the ISSU process is in progress install "The low order byte of the configuration register " "should be 0x02 during the upgrade process" ISSU_PROCESS-3-TRANSFORM 3-Error [chars] [ [chars] ] The ISSU process transform utility had an error. install "Send the output of 'show version' from the Active " "and the Standby and send it to TAC." ISSU_PROCESS-3-TRANSFORM 3-Error [chars] [ [chars] ] The ISSU process transform utility had an error. install "Send the output of 'show version' from the Active " "and the Standby and send it to TAC." ISSU_PROCESS-3-UAM 3-Error [chars] [chars] Return code failure from calling UAM API. install "Got unexpected rc from calling UAM API." ISSU_PROCESS-3-UAM 3-Error [chars] [chars] Return code failure from calling UAM API. install "Got unexpected rc from calling UAM API." ISSU_PROCESS-4-ABORT_ISSU 4-Warning [chars] The peer has been determined to be incompatible and hence is being reloaded. install "Send the output of 'show redundancy history' from " "the Active to TAC." ISSU_PROCESS-4-ABORT_ISSU 4-Warning [chars] The peer has been determined to be incompatible and hence is being reloaded. install "Send the output of 'show redundancy history' from " "the Active to TAC." ISSU_PROCESS-4-ACCEPTVERSION_WARNING 4-Warning ISSU auto-rollback will be initiated in [dec] minutes. It shows the warning message several minutes before the expiration of rollback timer install "Issue the acceptversion command before the " "expiration of rollback timer" ISSU_PROCESS-4-ACCEPTVERSION_WARNING 4-Warning ISSU auto-rollback will be initiated in [dec] minutes. It shows the warning message several minutes before the expiration of rollback timer install "Issue the acceptversion command before the " "expiration of rollback timer" ISSU_PROCESS-6-COMMITVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-COMMITVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-LOADVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-LOADVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-RUNVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-RUNVERSION_INFO 6-Information [chars] Provides the issu state information install "Observe the status message" ISSU_PROCESS-6-SELF_RELOAD 6-Information slot [dec] countdown to self-reload started [dec] second delay\n Self reload from Upgrade Director's instructions install "Log the circumstances" ISSU_PROCESS-6-SELF_RELOAD 6-Information slot [dec] countdown to self-reload started [dec] second delay\n Self reload from Upgrade Director's instructions install "Log the circumstances" ISSU_PROCESS-6-SELF_RELOAD_CANCEL 6-Information Self-reload cancelled on slot [dec]\n Cancel of self-reload from user 'abort' instruction install "Log the circumstances" ISSU_PROCESS-6-SELF_RELOAD_CANCEL 6-Information Self-reload cancelled on slot [dec]\n Cancel of self-reload from user 'abort' instruction install "Log the circumstances" ISSU_PROCESS-7-DEBUG 7-Debug [chars] Debug commands for the ISSU process. The system is \nattempting to recover from an unknown error.\n install "Send the output of 'show logging' to TAC for " "debugging purposes." ISSU_PROCESS-7-DEBUG 7-Debug [chars] Debug commands for the ISSU process. The system is \nattempting to recover from an unknown error.\n install "Send the output of 'show logging' to TAC for " "debugging purposes." ISSU_XFORM-3-LDP 3-Error ERRMSG_NOFLAGS - - - ISSU_XFORM-3-LDP 3-Error ERRMSG_NOFLAGS - - - ISSU-3-BAD_PARAMS 3-Error [chars] Bad parameters are being passed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-BAD_PARAMS 3-Error [chars] Bad parameters are being passed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-BASE_CLIENT_CHECK_COMPATIBILITY 3-Error [chars] Error found during checking of ISSU base client compatibility ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-BASE_CLIENT_CHECK_COMPATIBILITY 3-Error [chars] Error found during checking of ISSU base client compatibility ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-CAP_TABLE_OUT_OF_BOUND 3-Error Cap_table_count [dec] is out of bound max is [dec] for The cap_table_count is out of bound for the cap_entry_id. ha-issu-infra "Copy the error and send it to TAC. TAC team " "can contact ISSU infrastructure team to check why the count " "is out of bound for the cap_entry_id." ISSU-3-CAP_TABLE_OUT_OF_BOUND 3-Error Cap_table_count [dec] is out of bound max is [dec] for The cap_table_count is out of bound for the cap_entry_id. ha-issu-infra "Copy the error and send it to TAC. TAC team " "can contact ISSU infrastructure team to check why the count " "is out of bound for the cap_entry_id." ISSU-3-CLIENT_OR_ENTITY_NOT_REG 3-Error Client [chars][dec] or entity[dec] is not registered [chars]. - - - ISSU-3-CLIENT_OR_ENTITY_NOT_REG 3-Error Client [chars][dec] or entity[dec] is not registered [chars]. - - - ISSU-3-CLIENT_REG_DIST 3-Error Failed to [chars] distributed client [dec] Distributed client reservation or unreservation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-CLIENT_REG_DIST 3-Error Failed to [chars] distributed client [dec] Distributed client reservation or unreservation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-DEBUG_ERROR 3-Error [chars] Error happens when turning on ISSU debug. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-DEBUG_ERROR 3-Error [chars] Error happens when turning on ISSU debug. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-DUMMY_VERSION_OUT_OF_RANGE 3-Error Dummy msg version [dec] is out of range for msg[dec] under client [chars][dec] and entity[dec]. dummy msg version is out of range ha-issu-infra "'show issu message type | include ' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-DUMMY_VERSION_OUT_OF_RANGE 3-Error Dummy msg version [dec] is out of range for msg[dec] under client [chars][dec] and entity[dec]. dummy msg version is out of range ha-issu-infra "'show issu message type | include ' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-DUMY_ENTRY_NOT_LAST 3-Error Dumy cap entry is not last one for cap group[dec] registration Dumy cap entry is not last one for cap group registration ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dumy entry is not last one during registration" ISSU-3-DUMY_ENTRY_NOT_LAST 3-Error Dumy cap entry is not last one for cap group[dec] registration Dumy cap entry is not last one for cap group registration ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dumy entry is not last one during registration" ISSU-3-DUP_DUMMY_VERSION_REG 3-Error [chars] is already registered under client [chars][dec] entity[dec] and msgtype[dec] Item is registered already under that msg type. ha-issu-infra "'show issu message type | include ' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-DUP_DUMMY_VERSION_REG 3-Error [chars] is already registered under client [chars][dec] entity[dec] and msgtype[dec] Item is registered already under that msg type. ha-issu-infra "'show issu message type | include ' and copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-DUP_ENTITY_REG 3-Error Entity[dec] is registered already under client [chars][dec] - - - ISSU-3-DUP_ENTITY_REG 3-Error Entity[dec] is registered already under client [chars][dec] - - - ISSU-3-DUP_ITEM_IN_REG_UNDER_ENTITY 3-Error [chars] is duplicated [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-DUP_ITEM_IN_REG_UNDER_ENTITY 3-Error [chars] is duplicated [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-DUP_REG_ENDPOINT 3-Error Endpoint is registered already. Endpoint is registered already. ha-issu-infra "'show issu endpoint' to check if ISSU subsystem \n\is initialized twice." ISSU-3-DUP_REG_ENDPOINT 3-Error Endpoint is registered already. Endpoint is registered already. ha-issu-infra "'show issu endpoint' to check if ISSU subsystem \n\is initialized twice." ISSU-3-DUP_REG_UNDER_ENDPOINT 3-Error [chars][dec] is registered already under endpoint. Item is registered already under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item is registered already if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-DUP_REG_UNDER_ENDPOINT 3-Error [chars][dec] is registered already under endpoint. Item is registered already under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item is registered already if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-DUP_REG_UNDER_ENTITY 3-Error [chars][dec] is registered already under client [chars][dec] and Item is registered already under client and entity. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported items under entity is registered already" ISSU-3-DUP_REG_UNDER_ENTITY 3-Error [chars][dec] is registered already under client [chars][dec] and Item is registered already under client and entity. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported items under entity is registered already" ISSU-3-EMPTY_DUMMY_VERSION 3-Error [chars] is empty under client [chars][dec] entity[dec]. dummy version is empty. ha-issu-infra "copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-EMPTY_DUMMY_VERSION 3-Error [chars] is empty under client [chars][dec] entity[dec]. dummy version is empty. ha-issu-infra "copy the error and send it to TAC. TAC team can contact ISSU team to check why reported item is registered already" ISSU-3-EMPTY_UNDER_CLIENT 3-Error [chars] is empty under client [chars][dec]. Item is empty in client. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item under client is empty" ISSU-3-EMPTY_UNDER_CLIENT 3-Error [chars] is empty under client [chars][dec]. Item is empty in client. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported item under client is empty" ISSU-3-EMPTY_UNDER_ENDPOINT 3-Error [chars] is empty under endpoint. Item is empty under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is empty if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-EMPTY_UNDER_ENDPOINT 3-Error [chars] is empty under endpoint. Item is empty under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is empty if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-EMPTY_UNDER_ENTITY 3-Error [chars] is empty [chars] under client [chars][dec] and entity[dec]. - - - ISSU-3-EMPTY_UNDER_ENTITY 3-Error [chars] is empty [chars] under client [chars][dec] and entity[dec]. - - - ISSU-3-ENDPOINT_NOT_REG 3-Error Endpoint is not registered yet. Endpoint is not registered yet. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact ISSU infrastruture team to check why endpoint is not registered" ISSU-3-ENDPOINT_NOT_REG 3-Error Endpoint is not registered yet. Endpoint is not registered yet. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact ISSU infrastruture team to check why endpoint is not registered" ISSU-3-ERP_AGENT 3-Error [chars] The send message function call failed. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP agent failed" ISSU-3-ERP_AGENT 3-Error [chars] The send message function call failed. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP agent failed" ISSU-3-ERP_CLIENT 3-Error For context ID [dec] [chars] One of the primary functions for the ERP client failed. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP client failed" ISSU-3-ERP_CLIENT 3-Error For context ID [dec] [chars] One of the primary functions for the ERP client failed. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why one of the primary functions for the ERP client failed" ISSU-3-ERP_CLIENT_EVENT 3-Error Unknown [chars] event - [dec] An unknown event was received ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why an unknown event was received" ISSU-3-ERP_CLIENT_EVENT 3-Error Unknown [chars] event - [dec] An unknown event was received ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why an unknown event was received" ISSU-3-EXTERNAL_MATRIX_FILE_ERR 3-Error Line [dec]: [chars] External matrix file data is corrupted ha-issu-infra "An error was found in the external " "matrix data file. Open a case with TAC and attach output of " "more ivfs:/ command " "where is the output of dir " "system:image command." ISSU-3-EXTERNAL_MATRIX_FILE_ERR 3-Error Line [dec]: [chars] External matrix file data is corrupted ha-issu-infra "An error was found in the external " "matrix data file. Open a case with TAC and attach output of " "more ivfs:/ command " "where is the output of dir " "system:image command." ISSU-3-FAILED_TO_ALLOC_CHUNK_MEMORY 3-Error chunk allocation for [chars] failed. Chunk malloc failed. ha-issu-infra "copy the error and send it to TAC. TAC team can \n\contact ISSU client team" ISSU-3-FAILED_TO_ALLOC_CHUNK_MEMORY 3-Error chunk allocation for [chars] failed. Chunk malloc failed. ha-issu-infra "copy the error and send it to TAC. TAC team can \n\contact ISSU client team" ISSU-3-FAILED_TO_ALLOC_DUMMY_VERSION 3-Error Can not allocate [chars] under client [chars][dec] and entity[dec] Can not allocate dummy version under client and entity. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_DUMMY_VERSION 3-Error Can not allocate [chars] under client [chars][dec] and entity[dec] Can not allocate dummy version under client and entity. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_ENTITY 3-Error Can not allocate entity[dec] under client [chars][dec] Can not allocate entity control block under client. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_ENTITY 3-Error Can not allocate entity[dec] under client [chars][dec] Can not allocate entity control block under client. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENDPOINT 3-Error Can not allocate [chars][dec] [chars]. Can not allocate function callback. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead" ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENDPOINT 3-Error Can not allocate [chars][dec] [chars]. Can not allocate function callback. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead" ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENTITY 3-Error Can not allocate [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-FAILED_TO_ALLOC_FUNCT_UNDER_ENTITY 3-Error Can not allocate [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-FAILED_TO_ALLOC_MEMORY 3-Error memory allocation for [chars] failed. malloc failed. ha-issu-infra "copy the error and send it to TAC. TAC team can \n\contact ISSU client team" ISSU-3-FAILED_TO_ALLOC_MEMORY 3-Error memory allocation for [chars] failed. malloc failed. ha-issu-infra "copy the error and send it to TAC. TAC team can \n\contact ISSU client team" ISSU-3-FAILED_TO_ALLOC_UNDER_ENDPOINT 3-Error Can not allocate [chars] [chars][dec] control block. Can not allocate control block. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead" ISSU-3-FAILED_TO_ALLOC_UNDER_ENDPOINT 3-Error Can not allocate [chars] [chars][dec] control block. Can not allocate control block. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. 'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\if client problem reported. Otherwise contact ISSU infrastructure team instead" ISSU-3-FAILED_TO_ALLOC_UNDER_ENTITY 3-Error Can not allocate [chars][dec] under client [chars][dec] and entity[dec] - - - ISSU-3-FAILED_TO_ALLOC_UNDER_ENTITY 3-Error Can not allocate [chars][dec] under client [chars][dec] and entity[dec] - - - ISSU-3-FAILED_TO_ALLOC_UNDER_GROUP 3-Error Can not allocate [chars][dec] for [chars][dec] registration under client Can not allocate item for group registration under client and entity. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_UNDER_GROUP 3-Error Can not allocate [chars][dec] for [chars][dec] registration under client Can not allocate item for group registration under client and entity. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_UNDER_MSG 3-Error Can not allocate [chars] for msg [dec] registration under client Can not allocate control block for msg registration. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_UNDER_MSG 3-Error Can not allocate [chars] for msg [dec] registration under client Can not allocate control block for msg registration. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_UNDER_MSG_SES 3-Error Can not allocate [chars] for msg session[dec] registration under Can not allocate control block for msg session registration. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_ALLOC_UNDER_MSG_SES 3-Error Can not allocate [chars] for msg session[dec] registration under Can not allocate control block for msg session registration. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_CREATE_ID32_SPACE 3-Error Failed to create ID32 space. Failed to create ID32 space. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_CREATE_ID32_SPACE 3-Error Failed to create ID32 space. Failed to create ID32 space. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_INIT_ISSU_PROTO 3-Error Failed to initialize ISSU proto. Failed to initialize ISSU proto. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why ISSU protocol can not initialize correctly" ISSU-3-FAILED_TO_INIT_ISSU_PROTO 3-Error Failed to initialize ISSU proto. Failed to initialize ISSU proto. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why ISSU protocol can not initialize correctly" ISSU-3-FAILED_TO_UNREG_SES 3-Error Failed to unregister [chars] session under client [chars][dec] and Failed to unregister session. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FAILED_TO_UNREG_SES 3-Error Failed to unregister [chars] session under client [chars][dec] and Failed to unregister session. ha-issu-infra "'show proc mem' or 'show buffs' to check if memory \n\or buffer is full. shutdown unused tasks or reset cards usually can recover \n\those memory leak problem. Copy the error and send it to TAC if those actions \n\does not help." ISSU-3-FOF_NEGO_RESULT_INCONSISTENT 3-Error FOF owner msg type [dec] of owner client [chars][dec] entity [dec]. An owner FOF message of interest to an using client has inconsistent negotiation results in different owner sessions under the same entity ha-issu-infra "Copy the error and send it to TAC. TAC team can " "contact ISSU infrastructure team to investigate " "the problem." ISSU-3-FOF_NEGO_RESULT_INCONSISTENT 3-Error FOF owner msg type [dec] of owner client [chars][dec] entity [dec]. An owner FOF message of interest to an using client has inconsistent negotiation results in different owner sessions under the same entity ha-issu-infra "Copy the error and send it to TAC. TAC team can " "contact ISSU infrastructure team to investigate " "the problem." ISSU-3-FSM_BADMSG 3-Error Peer session [dec] while receiving message [chars] is wrong. Session are mismatched on peers or not found. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id." ISSU-3-FSM_BADMSG 3-Error Peer session [dec] while receiving message [chars] is wrong. Session are mismatched on peers or not found. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id." ISSU-3-FSM_DUP_UID 3-Error Duplicate unique_id on session [dec]: my_uid [dec] peer_uid [dec]. Violate the requirement that each endpoint must have distinctive \n\ identifier. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint" ISSU-3-FSM_DUP_UID 3-Error Duplicate unique_id on session [dec]: my_uid [dec] peer_uid [dec]. Violate the requirement that each endpoint must have distinctive \n\ identifier. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint" ISSU-3-FSM_INIT 3-Error Fail to create process during FSM init. The creation of FSM timer process fails. ha-issu-infra "User should check system resource during bootup\n\ time." ISSU-3-FSM_INIT 3-Error Fail to create process during FSM init. The creation of FSM timer process fails. ha-issu-infra "User should check system resource during bootup\n\ time." ISSU-3-FSM_MISMATCH_MTU 3-Error ISSU nego failed for client [chars][dec] entity_id [dec] session [dec] due to mismatch of mtu size [dec] & [dec]. - - - ISSU-3-FSM_MISMATCH_MTU 3-Error ISSU nego failed for client [chars][dec] entity_id [dec] session [dec] due to mismatch of mtu size [dec] & [dec]. - - - ISSU-3-FSM_NEGO_SEND_ERR 3-Error Client '[chars]' with ID [dec] encountered '[chars]' in session [dec]. Creation/removal of the named port failed for IPC. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why creation/removal of the named port failed for IPC" ISSU-3-FSM_NEGO_SEND_ERR 3-Error Client '[chars]' with ID [dec] encountered '[chars]' in session [dec]. Creation/removal of the named port failed for IPC. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why creation/removal of the named port failed for IPC" ISSU-3-FSM_RUNTIME_ERR 3-Error Client '[chars]' with ID [dec] has '[chars]' in session [dec]. Runtime error occurs during FSM negotiation. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why this runtime error occurs. Use 'show issu fsm | include '\n\to get error reason for futher debug." ISSU-3-FSM_RUNTIME_ERR 3-Error Client '[chars]' with ID [dec] has '[chars]' in session [dec]. Runtime error occurs during FSM negotiation. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why this runtime error occurs. Use 'show issu fsm | include '\n\to get error reason for futher debug." ISSU-3-HANDLE_SIZE 3-Error Handle buffer size is [dec] should be [dec] Statically defined handle buffer size is incorrect ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-HANDLE_SIZE 3-Error Handle buffer size is [dec] should be [dec] Statically defined handle buffer size is incorrect ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-IN_USE_UNDER_ENDPOINT 3-Error [chars][dec] is in use under endpoint Item is in use under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-IN_USE_UNDER_ENDPOINT 3-Error [chars][dec] is in use under endpoint Item is in use under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-IN_USE_UNDER_ENTITY 3-Error [chars][dec] is in use under client [chars][dec] and entity[dec] - - - ISSU-3-IN_USE_UNDER_ENTITY 3-Error [chars][dec] is in use under client [chars][dec] and entity[dec] - - - ISSU-3-INCOMPATIBLE_BASE_CLIENTS 3-Error [chars]\n List of ISSU base clients found incompatible ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-INCOMPATIBLE_BASE_CLIENTS 3-Error [chars]\n List of ISSU base clients found incompatible ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-INCOMPATIBLE_PEER_UID 3-Error Setting image [chars] version [chars] on peer uid [dec] as incompatible Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-INCOMPATIBLE_PEER_UID 3-Error Setting image [chars] version [chars] on peer uid [dec] as incompatible Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-INCONSISTENT_MSG_TYPE 3-Error [chars] Foreign owned field transformation failed ha-issu-infra "Copy the error and send it to TAC." ISSU-3-INCONSISTENT_MSG_TYPE 3-Error [chars] Foreign owned field transformation failed ha-issu-infra "Copy the error and send it to TAC." ISSU-3-INTERRUPT_LEVEL_SESSION_OPERATION 3-Error [chars] [chars] [dec] [chars] [dec] ISSU session registeration or unregisteration should not be done at interrupt level ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-INTERRUPT_LEVEL_SESSION_OPERATION 3-Error [chars] [chars] [dec] [chars] [dec] ISSU session registeration or unregisteration should not be done at interrupt level ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-INVALID_ITEM_UNDER_ENDPOINT 3-Error Invalid [chars] under endpoint Invalid item under endpoint ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why invalid item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-INVALID_ITEM_UNDER_ENDPOINT 3-Error Invalid [chars] under endpoint Invalid item under endpoint ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why invalid item is used if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-INVALID_ITEM_UNDER_ENTITY 3-Error Invalid [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-INVALID_ITEM_UNDER_ENTITY 3-Error Invalid [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-INVALID_PARAM_UNDER_SES 3-Error Invalid params [chars] under session[dec] Invalid parameters under session ha-issu-infra "'show issu session | include ' \n\to find out which client's session is causing this error msg. \n\copy the error and send it to TAC. TAC team can contact ISSU team to \n\check why invalid params is used if problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-INVALID_PARAM_UNDER_SES 3-Error Invalid params [chars] under session[dec] Invalid parameters under session ha-issu-infra "'show issu session | include ' \n\to find out which client's session is causing this error msg. \n\copy the error and send it to TAC. TAC team can contact ISSU team to \n\check why invalid params is used if problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-INVALID_VERSION_LOWHIGH 3-Error Invalid low[dec] and high[dec] value for msg[dec] under client Invalid low and high value for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why invalid low or high version is used for group registration" ISSU-3-INVALID_VERSION_LOWHIGH 3-Error Invalid low[dec] and high[dec] value for msg[dec] under client Invalid low and high value for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why invalid low or high version is used for group registration" ISSU-3-ISSU_INIT_NOT_COMPLETE 3-Error [chars] ISSU initialization has not been completed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-ISSU_INIT_NOT_COMPLETE 3-Error [chars] ISSU initialization has not been completed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-JID 3-Error Failed to get the local process JID with err [dec] The system manager call to collect the job-id failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-JID 3-Error Failed to get the local process JID with err [dec] The system manager call to collect the job-id failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-MISSING_ITEM_IN_REG 3-Error [chars][dec] is not available [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-MISSING_ITEM_IN_REG 3-Error [chars][dec] is not available [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-MSG_NEGO_RESULT_CHUNK 3-Error Failed to [chars] element [hec] Failed to lock or free the message negociation result chunk element ha-issu-infra "MSG negociation result element is locked and unlocked during avl_walk_extended of msg_nego_result_cb_root. The failure to lock or free of the element indicates invalid element or corrupted chunk memory. Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-MSG_NEGO_RESULT_CHUNK 3-Error Failed to [chars] element [hec] Failed to lock or free the message negociation result chunk element ha-issu-infra "MSG negociation result element is locked and unlocked during avl_walk_extended of msg_nego_result_cb_root. The failure to lock or free of the element indicates invalid element or corrupted chunk memory. Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-MSG_SES_IN_MSG_NOT_FOUND 3-Error The intended session [dec] specified in received [chars] for client [chars][dec] is not found. Cannot find the session with the session id\n\ specified in the received message. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id." ISSU-3-MSG_SES_IN_MSG_NOT_FOUND 3-Error The intended session [dec] specified in received [chars] for client [chars][dec] is not found. Cannot find the session with the session id\n\ specified in the received message. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to make sure that receiving path uses correct session id." ISSU-3-NO_PEER_UID 3-Error No peer uid found at [chars] No peer uid with this value found registered in ISSU Database ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no peer uid with this value foundi registered in ISSU Database" ISSU-3-NO_PEER_UID 3-Error No peer uid found at [chars] No peer uid with this value found registered in ISSU Database ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no peer uid with this value foundi registered in ISSU Database" ISSU-3-NO_UID 3-Error No uid [dec] registered with ISSU at [chars] No uid with this value found registered in ISSU Database ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no uid with this value found registered in ISSU Database" ISSU-3-NO_UID 3-Error No uid [dec] registered with ISSU at [chars] No uid with this value found registered in ISSU Database ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why no uid with this value found registered in ISSU Database" ISSU-3-NON_ISSU_ID_UNDER_ENDPOINT 3-Error Non ISSU [chars] Peer endpoint does not support ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why non-issu ID is used" ISSU-3-NON_ISSU_ID_UNDER_ENDPOINT 3-Error Non ISSU [chars] Peer endpoint does not support ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why non-issu ID is used" ISSU-3-NOT_DUMY_CAP_TYPE 3-Error Cap type[dec] is not dumy one. Cap type is not dumy one. ha-issu-infra "'show issu cap type | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dummy cap type is not used" ISSU-3-NOT_DUMY_CAP_TYPE 3-Error Cap type[dec] is not dumy one. Cap type is not dumy one. ha-issu-infra "'show issu cap type | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why dummy cap type is not used" ISSU-3-NOT_FIND_FUNCT_UNDER_SESSION 3-Error Can not find [chars] under [chars] session[dec]. Can not find function under session. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found" ISSU-3-NOT_FIND_FUNCT_UNDER_SESSION 3-Error Can not find [chars] under [chars] session[dec]. Can not find function under session. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found" ISSU-3-NOT_FIND_MSG_SES 3-Error Can not find message session[dec] [chars]. - - - ISSU-3-NOT_FIND_MSG_SES 3-Error Can not find message session[dec] [chars]. - - - ISSU-3-NOT_FIND_UNDER_ENDPOINT 3-Error Can not find [chars]0x[hec] control block under endpoint. - - - ISSU-3-NOT_FIND_UNDER_ENDPOINT 3-Error Can not find [chars]0x[hec] control block under endpoint. - - - ISSU-3-NOT_FIND_UNDER_ENTITY 3-Error Can not find [chars][dec] control block under client [chars][dec] and Can not find control block under client and entity. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control blcok can not be found" ISSU-3-NOT_FIND_UNDER_ENTITY 3-Error Can not find [chars][dec] control block under client [chars][dec] and Can not find control block under client and entity. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control blcok can not be found" ISSU-3-NOT_FIND_UNDER_SESSION 3-Error Can not find [chars][dec] under [chars] session[dec]. Can not find item under session. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found" ISSU-3-NOT_FIND_UNDER_SESSION 3-Error Can not find [chars][dec] under [chars] session[dec]. Can not find item under session. ha-issu-infra "'show issu session | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why control block under session can not be found" ISSU-3-NOT_REG_UNDER_ENDPOINT 3-Error [chars][dec] is not registered under endpoint. Item is not registered under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is not registered if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-NOT_REG_UNDER_ENDPOINT 3-Error [chars][dec] is not registered under endpoint. Item is not registered under endpoint. ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported item is not registered if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-NOT_REG_UNDER_ENTITY 3-Error [chars][dec] is not registered under client [chars][dec] and entity[dec] - - - ISSU-3-NOT_REG_UNDER_ENTITY 3-Error [chars][dec] is not registered under client [chars][dec] and entity[dec] - - - ISSU-3-NULL_CALLBACK_UNDER_ENDPOINT 3-Error [chars] callback is NULL for registration. Callback is NULL for registration ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported callback is NULL if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-NULL_CALLBACK_UNDER_ENDPOINT 3-Error [chars] callback is NULL for registration. Callback is NULL for registration ha-issu-infra "'show issu client | include ' \n\copy the error and send it to TAC. TAC team can contact ISSU client team to \n\check why reported callback is NULL if client problem reported. \n\Otherwise contact ISSU infrastructure team instead" ISSU-3-NULL_CALLBACK_UNDER_ENTITY 3-Error [chars] callback is NULL for msg session registration under client [chars][dec] and entity[dec] Callback is NULL for msg session registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported callback is NULL" ISSU-3-NULL_CALLBACK_UNDER_ENTITY 3-Error [chars] callback is NULL for msg session registration under client [chars][dec] and entity[dec] Callback is NULL for msg session registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why reported callback is NULL" ISSU-3-NULL_CALLBACK_UNDER_SESSION 3-Error Can not register null [chars] callback in [chars] session[dec]. - - - ISSU-3-NULL_CALLBACK_UNDER_SESSION 3-Error Can not register null [chars] callback in [chars] session[dec]. - - - ISSU-3-PEER_IMAGE_INCOMPATIBLE 3-Error Peer image [chars] version [chars] on peer uid [dec] is incompatible Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_IMAGE_INCOMPATIBLE 3-Error Peer image [chars] version [chars] on peer uid [dec] is incompatible Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_IMAGE_NOT_IN_INCOMP_LIST 3-Error Peer image [chars] version [chars] on peer uid [dec] is not in the Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_IMAGE_NOT_IN_INCOMP_LIST 3-Error Peer image [chars] version [chars] on peer uid [dec] is not in the Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_IMAGE_REM_FROM_INCOMP_LIST 3-Error Peer image [chars] version [chars] on peer uid [dec] being removed Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_IMAGE_REM_FROM_INCOMP_LIST 3-Error Peer image [chars] version [chars] on peer uid [dec] being removed Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_INCOMP_SET 3-Error Peer incompatibility set for image [chars] version [chars] on peer Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_INCOMP_SET 3-Error Peer incompatibility set for image [chars] version [chars] on peer Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_UID_CB_IS_NULL 3-Error Peer uid control block is NULL Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PEER_UID_CB_IS_NULL 3-Error Peer uid control block is NULL Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-PROTO_CLIENT_ENTITY_UNREG 3-Error Proto Client entity unreg for [chars] has failed Protocol client has failed to unregister its entity with ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to unregister its entity with ISSU" ISSU-3-PROTO_CLIENT_ENTITY_UNREG 3-Error Proto Client entity unreg for [chars] has failed Protocol client has failed to unregister its entity with ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to unregister its entity with ISSU" ISSU-3-PROTO_CLIENT_REG 3-Error Proto Client registration for [chars] has failed Protocol client has failed to register with ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to register with ISSU" ISSU-3-PROTO_CLIENT_REG 3-Error Proto Client registration for [chars] has failed Protocol client has failed to register with ISSU ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastructure team to check \n\why protocol client has failed to register with ISSU" ISSU-3-REF_TREE 3-Error [chars] reference tree [chars] failed The AVL based ISSU reference tree operation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-REF_TREE 3-Error [chars] reference tree [chars] failed The AVL based ISSU reference tree operation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-SESSION_ID_ERROR 3-Error Failed to [chars] session id [dec] for [chars] Session ID related operation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-SESSION_ID_ERROR 3-Error Failed to [chars] session id [dec] for [chars] Session ID related operation failed ha-issu-infra "Copy the error and send it to TAC. TAC team can contact ISSU infrastructure team to investigate the problem." ISSU-3-SESSION_RENEGOTIATE 3-Error Client Attempting to renegotiate on session [dec] Client Attempting to renegotiate session ha-issu-infra "A Client is attempting to renegotiate on session\n\without unregistering it and do the negotiation over again. This is not allowed\n\and is considered an error condition. The client should unregister the msg\n\session first and then re-register and attempt the negotiation." ISSU-3-SESSION_RENEGOTIATE 3-Error Client Attempting to renegotiate on session [dec] Client Attempting to renegotiate session ha-issu-infra "A Client is attempting to renegotiate on session\n\without unregistering it and do the negotiation over again. This is not allowed\n\and is considered an error condition. The client should unregister the msg\n\session first and then re-register and attempt the negotiation." ISSU-3-SET_UNKNOWN_UID 3-Error Unknown unique_id is set. Platform team should provide distinctive identifier for endpoint. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint" ISSU-3-SET_UNKNOWN_UID 3-Error Unknown unique_id is set. Platform team should provide distinctive identifier for endpoint. ha-issu-infra "Copy the error and send it to TAC. \n\TAC team can contact platform team to provide distinctive identifier \n\for endpoint" ISSU-3-TRANSPORT_ERP_UID_CB_IS_NULL 3-Error Transport ERP uid control block is NULL Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-TRANSPORT_ERP_UID_CB_IS_NULL 3-Error Transport ERP uid control block is NULL Peer is incompatible ha-issu-infra "A runtime exception occurred in the previous run.\n\Clear the condition according to the client eg. config-sync and reload \n\the Standby" ISSU-3-UNKNOWN_DOMAIN_ID 3-Error Unknown domain id [dec] under client [chars][dec] entity [dec] - - - ISSU-3-UNKNOWN_DOMAIN_ID 3-Error Unknown domain id [dec] under client [chars][dec] entity [dec] - - - ISSU-3-UNKNOWN_ENTITY_ID 3-Error Unknown entity id under client [chars][dec] Unknown entity id under client ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why unknown entity id is used during registration" ISSU-3-UNKNOWN_ENTITY_ID 3-Error Unknown entity id under client [chars][dec] Unknown entity id under client ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why unknown entity id is used during registration" ISSU-3-UNKNOWN_ID_UNDER_ENDPOINT 3-Error Can not use unknown [chars]. Can not use unknown id. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why unknown ID is used" ISSU-3-UNKNOWN_ID_UNDER_ENDPOINT 3-Error Can not use unknown [chars]. Can not use unknown id. ha-issu-infra "Copy the error and send it to TAC.\n\TAC team can contact ISSU infrastruture team to check why unknown ID is used" ISSU-3-UNKNOWN_ID_UNDER_ENTITY 3-Error Unknown [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-UNKNOWN_ID_UNDER_ENTITY 3-Error Unknown [chars] under client [chars][dec] and entity[dec] - - - ISSU-3-VERSION_LOWHIGH_NOT_MATCH_TABLE_SIZE 3-Error Version low[dec] and high[dec] value for msg[dec] does not Version low and high value for msg does not match table size. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why low/high version is not macth table size for msg registration" ISSU-3-VERSION_LOWHIGH_NOT_MATCH_TABLE_SIZE 3-Error Version low[dec] and high[dec] value for msg[dec] does not Version low and high value for msg does not match table size. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why low/high version is not macth table size for msg registration" ISSU-3-VERSION_OUT_OF_ORDER 3-Error Msg version[dec][dec] is out of order for msg[dec] under client Msg version is out of order for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of order for msg registration" ISSU-3-VERSION_OUT_OF_ORDER 3-Error Msg version[dec][dec] is out of order for msg[dec] under client Msg version is out of order for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of order for msg registration" ISSU-3-VERSION_OUT_OF_RANGE 3-Error Msg version[dec][dec] is out of range for msg[dec] under client Msg version is out of range for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of range for group registration" ISSU-3-VERSION_OUT_OF_RANGE 3-Error Msg version[dec][dec] is out of range for msg[dec] under client Msg version is out of range for group registration. ha-issu-infra "'show issu client | include ' and \n\copy the error and send it to TAC. TAC team can contact ISSU client team \n\to check why version is out of range for group registration" ISSU-3-XFORM_CALLBACK 3-Error No [chars] callback specified for client [chars][dec] msg [dec] from version [dec] to version [dec] in session [dec] . Client didn't specify transformation function ha-issu-infra "Copy the error and send it to TAC. TAC team\n\ can contact ISSU client team to check why reported\n\ callback is not specified" ISSU-3-XFORM_CALLBACK 3-Error No [chars] callback specified for client [chars][dec] msg [dec] from version [dec] to version [dec] in session [dec] . Client didn't specify transformation function ha-issu-infra "Copy the error and send it to TAC. TAC team\n\ can contact ISSU client team to check why reported\n\ callback is not specified" ISSU-4-FSM_INCOMP 4-Warning Version of local ISSU client [chars][dec] in session [dec] is The protocol versions of the local and remote clients are\n\ incompatible. These clients can not communicate with each\n\ other. ha-issu-infra "Use 'show version' and 'show issu clients' to help\n\ verify that the software images are incompatible. Upgrade\n\ the software images on each unit to versions that are \n\ compatible. " LOG_STD_RECUR_ACTION ISSU-4-FSM_INCOMP 4-Warning Version of local ISSU client [chars][dec] in session [dec] is The protocol versions of the local and remote clients are\n\ incompatible. These clients can not communicate with each\n\ other. ha-issu-infra "Use 'show version' and 'show issu clients' to help\n\ verify that the software images are incompatible. Upgrade\n\ the software images on each unit to versions that are \n\ compatible. " LOG_STD_RECUR_ACTION ISSU-4-MSG_INCOMP 4-Warning Message[dec] is incompatible under msg session[dec]. - - - ISSU-4-MSG_INCOMP 4-Warning Message[dec] is incompatible under msg session[dec]. - - - ISSU-4-NEGO_NOT_FINISHED 4-Warning Negotiation is not finished for client [chars][dec] msg session[dec]. - - - ISSU-4-NEGO_NOT_FINISHED 4-Warning Negotiation is not finished for client [chars][dec] msg session[dec]. - - - ISYNC_CHKPT-3-LDP 3-Error ERRMSG_NOFLAGS - - - ISYNC_CHKPT-3-LDP 3-Error ERRMSG_NOFLAGS - - - ISYNC-3-LDP 3-Error ERRMSG_NOFLAGS - - - ISYNC-3-LDP 3-Error ERRMSG_NOFLAGS - - - ITEM_SIZE_TOO_BIG-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - ITEM_SIZE_TOO_BIG-3-MPLS_TE_HA 3-Error ERRMSG_NOFLAGS - - - IVR_MSB-3-INVALID_MAX_PROMPTS 3-Error [chars]: This version of IOS does not support prompt playout for IVR applications.\n This error will be displayed if an IVR application is used on a gateway that does\n\ not support IVR prompt playout. voice-ivr "Ensure that this platform and IOS version support the IVR feature set." IVR_MSB-3-INVALID_MAX_PROMPTS 3-Error [chars]: This version of IOS does not support prompt playout for IVR applications.\n This error will be displayed if an IVR application is used on a gateway that does\n\ not support IVR prompt playout. voice-ivr "Ensure that this platform and IOS version support the IVR feature set." IVR_MSB-3-INVALID_PROMPT_SIZE 3-Error [chars]: Bad size for the prompt file [chars]. Read size [dec]. Expected size [dec].\n Prompt file size error. File may be corrupted. voice-ivr "Replace the bad prompt file." IVR_MSB-3-INVALID_PROMPT_SIZE 3-Error [chars]: Bad size for the prompt file [chars]. Read size [dec]. Expected size [dec].\n Prompt file size error. File may be corrupted. voice-ivr "Replace the bad prompt file." IVR_MSB-3-NO_IO_MEMORY 3-Error [chars]: Failed to create pool_group [hec] buffer_pool [hec] platform_mc_buf_pool_count [dec]\n No IO memory to create IVR private pak pool voice-ivr "Check to see if there is enough IO memory." IVR_MSB-3-NO_IO_MEMORY 3-Error [chars]: Failed to create pool_group [hec] buffer_pool [hec] platform_mc_buf_pool_count [dec]\n No IO memory to create IVR private pak pool voice-ivr "Check to see if there is enough IO memory." IVR_MSB-3-NOPROMPT 3-Error Could not create IVR prompt\n [chars]\n errno=[dec]=[chars] Could not read in the IVR prompt voice-ivr "Check that prompt exists on the server and is readable." IVR_MSB-3-NOPROMPT 3-Error Could not create IVR prompt\n [chars]\n errno=[dec]=[chars] Could not read in the IVR prompt voice-ivr "Check that prompt exists on the server and is readable." IVR-1-APP_PARALLEL_INVALID_LIST 1-Alert Call terminated. Huntgroup '[dec]' does not contain enough valid SIP end-points to proceed with a parallel call. \n The call to a parallel hunt-group was denied because less than \n\ two valid SIP end-points were found in the huntgroup list. voice-ivr "Check the hunt-group list's numbers. Remove any incorrect numbers \n\ or numbers that have a non-SIP dial-peer. If the numbers are from\n\ SIP phones then verify whether the phones have registered to the\n\ system yet." IVR-1-APP_PARALLEL_INVALID_LIST 1-Alert Call terminated. Huntgroup '[dec]' does not contain enough valid SIP end-points to proceed with a parallel call. \n The call to a parallel hunt-group was denied because less than \n\ two valid SIP end-points were found in the huntgroup list. voice-ivr "Check the hunt-group list's numbers. Remove any incorrect numbers \n\ or numbers that have a non-SIP dial-peer. If the numbers are from\n\ SIP phones then verify whether the phones have registered to the\n\ system yet." IVR-2-APP_CRIT 2-Critical [chars]\n A critical message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-2-APP_CRIT 2-Critical [chars]\n A critical message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-2-APP_CRIT_R 2-Critical [chars]\n A critical message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-2-APP_CRIT_R 2-Critical [chars]\n A critical message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-2-INVALID_DSAPP_DIALPEER 2-Critical Service dsapp contains an invalid dial peer tag: [chars] An invalid dial peer tag has been configured for the dsapp service. The tag either is not in the range from 1 to 2147483647 or it belongs to a non-existent dial-peer. voice-ivr "Enter the show running-config " "or the show dial-peer voice " "command to find a valid dial peer tag. " "Reconfigure the dial peer with a valid tag or " "remove the dial peer tag completely to allow the " "system to match from the system dial peers." IVR-2-INVALID_DSAPP_DIALPEER 2-Critical Service dsapp contains an invalid dial peer tag: [chars] An invalid dial peer tag has been configured for the dsapp service. The tag either is not in the range from 1 to 2147483647 or it belongs to a non-existent dial-peer. voice-ivr "Enter the show running-config " "or the show dial-peer voice " "command to find a valid dial peer tag. " "Reconfigure the dial peer with a valid tag or " "remove the dial peer tag completely to allow the " "system to match from the system dial peers." IVR-3-ABNORMAL_EXIT 3-Error TCL IVR Process for this call with CallID [dec] exits bad event: [chars] received\n The TCL IVR call process exited for the specified call. The call \n\ process did not clear a prior call properly so other events could \n\ not be handled. Only the specified call is affected voice-ivr "If problem persists for subsequent callscopy the message exactly \n\ as it appears on the console or in the system log contact your \n\ Cisco technical support representative and provide the representative \n\ with the gathered information." IVR-3-ABNORMAL_EXIT 3-Error TCL IVR Process for this call with CallID [dec] exits bad event: [chars] received\n The TCL IVR call process exited for the specified call. The call \n\ process did not clear a prior call properly so other events could \n\ not be handled. Only the specified call is affected voice-ivr "If problem persists for subsequent callscopy the message exactly \n\ as it appears on the console or in the system log contact your \n\ Cisco technical support representative and provide the representative \n\ with the gathered information." IVR-3-APP_ERR 3-Error [chars]\n An error message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-3-APP_ERR 3-Error [chars]\n An error message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-3-APP_ERR_R 3-Error [chars]\n An error message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-3-APP_ERR_R 3-Error [chars]\n An error message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-3-BAD_IVR_VERSION 3-Error Script requires version [dec].[dec] image supports [dec].[dec]\n IVR Script requires a higher IVR infrastructure version voice-ivr "Upgrade IOS or use a different script" IVR-3-BAD_IVR_VERSION 3-Error Script requires version [dec].[dec] image supports [dec].[dec]\n IVR Script requires a higher IVR infrastructure version voice-ivr "Upgrade IOS or use a different script" IVR-3-BADSCRIPT 3-Error Could not parse malformed IVR script: [chars]\n Could not parse malformed IVR script voice-ivr "Check the script and fix the syntax error." IVR-3-BADSCRIPT 3-Error Could not parse malformed IVR script: [chars]\n Could not parse malformed IVR script voice-ivr "Check the script and fix the syntax error." IVR-3-LOW_MEMORY 3-Error IVR: Sytem running on low memory. Free memory: %l bytes. Call is rejected.\n System does not have enough CPU resources available to accept\n\ a new call voice-ivr "Ensure that the call setup rate is within the supported capacity of\n\ this gateway." IVR-3-LOW_MEMORY 3-Error IVR: Sytem running on low memory. Free memory: %l bytes. Call is rejected.\n System does not have enough CPU resources available to accept\n\ a new call voice-ivr "Ensure that the call setup rate is within the supported capacity of\n\ this gateway." IVR-3-NOSCRIPT 3-Error Could not load IVR script\n [chars]\n errno=[dec]=[chars] Could not read in the IVR script voice-ivr "Check that script exists on the server and is readable." IVR-3-NOSCRIPT 3-Error Could not load IVR script\n [chars]\n errno=[dec]=[chars] Could not read in the IVR script voice-ivr "Check that script exists on the server and is readable." IVR-4-APP_WARN 4-Warning [chars]\n A warning message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-4-APP_WARN 4-Warning [chars]\n A warning message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-4-APP_WARN_R 4-Warning [chars]\n A warning message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-4-APP_WARN_R 4-Warning [chars]\n A warning message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-4-INVALID_DSAPP_BLINDTIME 4-Warning Blind-xfer-wait-time [dec] is invalid. Resetting to [dec] seconds. The configured value for blind-xfer-wait-time was outside of the acceptable range 0-10 and has been reset to voice-ivr "If the new value for blind-xfer-wait-time is " "unacceptable you can change it from the command " " line interface." IVR-4-INVALID_DSAPP_BLINDTIME 4-Warning Blind-xfer-wait-time [dec] is invalid. Resetting to [dec] seconds. The configured value for blind-xfer-wait-time was outside of the acceptable range 0-10 and has been reset to voice-ivr "If the new value for blind-xfer-wait-time is " "unacceptable you can change it from the command " " line interface." IVR-4-INVALID_DSAPP_TOGGLE_TIME 4-Warning Disc-toggle-time [dec] is invalid. Resetting to [dec] seconds. The configured value for disc-toggle-time was outside of the acceptable range 10-30 and has been reset voice-ivr "If the new value for disc-toggle-time " "is unacceptable you can change it from the " "command line interface." IVR-4-INVALID_DSAPP_TOGGLE_TIME 4-Warning Disc-toggle-time [dec] is invalid. Resetting to [dec] seconds. The configured value for disc-toggle-time was outside of the acceptable range 10-30 and has been reset voice-ivr "If the new value for disc-toggle-time " "is unacceptable you can change it from the " "command line interface." IVR-5-APP_CALL_PREEMPTION 5-Notice CallID [dec] is being preempted\n A notification message was reported by an IVR application on detecting callID [dec] being preempted. voice-ivr "This is not a problem but notifying syslog about preempted call." IVR-5-APP_CALL_PREEMPTION 5-Notice CallID [dec] is being preempted\n A notification message was reported by an IVR application on detecting callID [dec] being preempted. voice-ivr "This is not a problem but notifying syslog about preempted call." IVR-5-APP_LOG_DUR_CALL_DETECTED 5-Notice [chars]\n System does not have enough CPU capacity to spawn a new instance of \n\ IVR application voice-ivr "Ensure that the call setup rate is within the supported capacity of\n\ this gateway." IVR-5-APP_LOG_DUR_CALL_DETECTED 5-Notice [chars]\n System does not have enough CPU capacity to spawn a new instance of \n\ IVR application voice-ivr "Ensure that the call setup rate is within the supported capacity of\n\ this gateway." IVR-5-APP_MED_INACT_DETECTED 5-Notice [chars]\n A notification message was reported by an IVR application on detecting media inactivity. voice-scripts "This is not a problem but notifying syslog about media inactivity." IVR-5-APP_MED_INACT_DETECTED 5-Notice [chars]\n A notification message was reported by an IVR application on detecting media inactivity. voice-scripts "This is not a problem but notifying syslog about media inactivity." IVR-5-APP_MED_REACT_DETECTED 5-Notice [chars]\n A notification message was reported by an IVR application on detecting media activity. voice-scripts "This is not a problem but notifying syslog about media activity." IVR-5-APP_MED_REACT_DETECTED 5-Notice [chars]\n A notification message was reported by an IVR application on detecting media activity. voice-scripts "This is not a problem but notifying syslog about media activity." IVR-6-APP_INFO 6-Information [chars]\n An informational message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-6-APP_INFO 6-Information [chars]\n An informational message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-6-APP_INFO_R 6-Information [chars]\n An informational message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-6-APP_INFO_R 6-Information [chars]\n An informational message was reported by an IVR Tcl application. voice-scripts "The remedy of the problem is application specific." IVR-6-APP_PARALLEL 6-Information Cannot use dial-peer [dec] parallel hunt-group for a rotary or The dial-peer for parallel hunt-groups must have a unique pilot number. voice-ivr "Create a unique dial-peer destination-number for the parallel \n\ hunt-group." IVR-6-APP_PARALLEL 6-Information Cannot use dial-peer [dec] parallel hunt-group for a rotary or The dial-peer for parallel hunt-groups must have a unique pilot number. voice-ivr "Create a unique dial-peer destination-number for the parallel \n\ hunt-group." IVR-6-APP_SEQ_HUNT 6-Information Pilot hunt-group '[chars]' found in hunt-group list. Nested hunt-groups are allowed only as the hunt-group's final number.\n Nested sequential hunt-group detected in dial-peer rotary. \n\ Nested hunt-groups is unsupported. voice-ivr "Do not create hunt-group lists that contain hunt-group pilot numbers." IVR-6-APP_SEQ_HUNT 6-Information Pilot hunt-group '[chars]' found in hunt-group list. Nested hunt-groups are allowed only as the hunt-group's final number.\n Nested sequential hunt-group detected in dial-peer rotary. \n\ Nested hunt-groups is unsupported. voice-ivr "Do not create hunt-group lists that contain hunt-group pilot numbers." IXP_MAP-3-ACR 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the ACR ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-ATOM 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the ATOM ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-CEM 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the CEM ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-CEMOUDP 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the CEMOUDP ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400 "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-DROP_BLOCK 3-Error [chars] error detected - 0x[hec] 0x[hec] [dec] [dec] Error detected processing ESF Network Processor drop block\n\ allocations. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-EXMEM 3-Error [chars] [chars] error detected - [chars] [dec] Error detected managing the external memory of a Network Processor. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-FRR_VLAN 3-Error Error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the FRR Vlan ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-HQF 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the HQF ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device. \n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-INITFAIL 3-Error Initialization Failed - [chars]: [chars] [chars] Memory needed to service one or more Network Processors\n\ could not be initialized. c7600-sip-400-clnt "Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-INTF 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the Interface ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device. \n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-IPSESS 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A configuration error for the IP Sessions ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persist reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-L2SRC 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A configuration error for the L2SRC ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-L2TPV3 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the L2TPV3 ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-LOCK_BLOCK 3-Error [chars] error detected - 0x[hec] [dec] [dec] [dec] Error detected processing ESF Network Processor lock bit\n\ allocations. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-LOCK_LIST 3-Error [chars] error detected - 0x[hec] [dec] [dec] [dec] Error detected processing ESF Network Processor lock bit list\n\ allocations. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-MAXEXCEED 3-Error ESF NP Mapper Max Services Exceeded - [chars]: [chars] [dec] The maximum number ESF Network Processor Client Mapper services have\n\ been exceeded. c7600-sip-400-clnt "Change the configuration to reduce the number of services configured.\n\ \n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-MPLSOGRE 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the MPLSOGRE ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-MPLSOMGRE 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the MPLSOGRE ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-NOMEM 3-Error Memory Allocation Failure - [chars] : [chars]0x[hec] Memory required to service one or more Network Processors\n\ could not be allocated. c7600-sip-400-clnt "This error may indicate that more memory \n\ must be installed on the affected card \n\ or platform in order to service all the\n\ features and related entities enabled via \n\ the configuration.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-NOMEM_S 3-Error Memory Allocation Failure - [chars]: [chars] [chars] Memory required to service one or more Network Processors could not\n\ be allocated. c7600-sip-400-clnt "This error may indicate that more memory \n\ must be installed on the affected card \n\ or platform in order to service all the\n\ features and related entities enabled via \n\ the configuration.\n\ \n\ Try to reload the IOS image on the affected \n\ card or platform.\n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-NOTFOUND 3-Error ESF NP Client Mapper - [chars]: [chars] 0x[hec] The ESF Network Processor Client Mapper could not locate a required \n\ software element. c7600-sip-400-clnt "Try to reload the IOS image on the affected \n\ card or platform.\n\\n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-NPMEM 3-Error [chars] [chars] error detected Error detected with external memory of a ESF Network Processor. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-NPUNKNOWN 3-Error Unsupported NP - [chars]: [chars] [chars] An unsupported Network Processor has been detected. c7600-sip-400-clnt "Verify that the correct IOS image is loaded on the affected \n\ card or platform for the configured features.\n\ If the error persists record the output\n\ from the following commands:\n\\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-PPPOESESS 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A configuration error for the PPPOE Sessions ESF Network Processor\n\ Client Mapper was detected. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-QOS 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the QOS ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-QOS_CONFIG 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A configuration error for the QOS ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Change the configuration to \n\ correct the QOS ACL configuration problem.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-SACL 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the Security ACL ESF Network\n\ Processor Client Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-SACL_CONFIG 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A configuration error for the Security ACL ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Change the configuration to \n\ correct the QOS ACL configuration problem.\n\ \n\ If the error persist record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-STATS_BLOCK 3-Error [chars] error detected - 0x[hec] 0x[hec] [dec] [dec] [dec] Error detected processing ESF Network Processor stats block\n\ allocations. c7600-sip-400-clnt "This is a software programming error. Record the \n\ Output from the following show commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-TCAM 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the NetLogic NSE TCAM was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-VPLS 3-Error Error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the VPLS ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\\n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-3-WRED 3-Error [chars] error detected: [chars] [chars] 0x[hec] 0x[hec] A software programming error for the WRED ESF Network Processor Client\n\ Mapper was detected. c7600-sip-400-clnt "This software programming error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. If the error persists reset\n\ the affected device.\n\ \n\ Record the output from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-4-CONNECTION_EXCEED 4-Warning The number of connections has reached the capacity of the line card [dec]. - - - IXP_MAP-4-IPC_FAIL 4-Warning ESF IPC Command failed - [chars] NP=[chars] cmd=[dec] me=[dec] rc=[dec] An IPC command sent to the ESF Network Processor failed. c7600-sip-400-clnt "This error indicates a possible problem with the\n\ Network Processor hardware or microcode. Reload\n\ the affected HW to clear the condition.\n\ \n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-4-QUEUE_LIMIT_EXCEED 4-Warning Warning: Line card default queue-limit exceeds the maximum transmit packet buffers [dec]. To ensure high priority traffic is An error for the HQF ESF Network Processor Client\n\ Mapper was detected. The total of the default queue-limits\n\ exceeds the maximum transmit packet buffers for this line card.\n\ Under high traffic conditions the line card may run out of \n\ packet buffers and drop high priority traffic. c7600-sip-400-clnt "This configuration error is not considered fatal to the\n\ operation of the ESF Network Processors. The software is designed to\n\ detect and report the error condition. Apply the QOS policy\n\ configuration in the output direction of each interface.\n\ Adjust the queue-limit so that the total of the queue-limits\n\ on this line card is less than the maximum transmit packet buffers.\n\ \n\ policy-map qlimit\n\ class class-default\n\ queue-limit 100000\n\\n\ interface Gig1/0/0\n\ service-policy output qlimit\n\\n\ If the error persist record the output from the following commands:\n\\n\ show policy-map interface \n\\n\ Provide this information to your technical support\n\ representative." IXP_MAP-4-STUCK 4-Warning Client ID0x[hec] 0x%08X not ready on [chars] During reset of the ESF Network Processor one or more Network\n\ Processor Clients had not completed stop processing. c7600-sip-400-clnt "The system should still operate normally however statistics\n\ or state collected before the ESF Network Processor was reset\n\ may have been lost.\n\\n\ If the error persists record the output\n\ from the following commands:\n\\n\ show tech \n\ show log \n\\n\ Provide this information to your technical support\n\ representative." KA_NOMEMORY-3-LDP 3-Error ERRMSG_NOFLAGS - - - KA_NOMEMORY-3-LDP 3-Error ERRMSG_NOFLAGS - - - KERBEROS-3-FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs call your technical support " "representative for assistance." KERBEROS-3-FORKFAIL 3-Error Failed to fork process for [chars]. Quite likely we ran out of memory. Other explanations are possible. aaa "If this message recurs call your technical support " "representative for assistance." KEYMAN-4-KEYSTR_BAD_CRYPTO 4-Warning Bad encrypted keystring for key id [dec]. The system could not successfully decrypt an encrypted keystring. The keystring may have been corrupted during system configuration. - "Re-enter the key-string command and reconfigure the key string." KEYMAN-4-KEYSTR_CRYPTO_TYPE 4-Warning Type [dec] encryption unknown. Interpreting keystring as literal The format type was not recognized by the system. A keystring format type value of 0 unencrypted keystring or 7 hidden keystring - "Use the correct format for the value type or remove the space following " "the value type" KEYSTORE_AE46C1-3-SELF_TEST_FAILURE 3-Error Keystore power on self test failure. [chars] keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state. - "Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced." KEYSTORE_AE46C1-3-SELF_TEST_FAILURE 3-Error Keystore power on self test failure. [chars] keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state. - "Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced." KEYSTORE_AE46C1-3-SELF_TEST_FAILURE 3-Error Keystore power on self test failure. [chars] keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state. - "Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced." KEYSTORE_AE46C1-3-SELF_TEST_FAILURE 3-Error Keystore power on self test failure. [chars] keystore pass power on self test failure for SHA1 or HMAC-SHA1. The chips is not usable in this state. - "Report this error to your Cisco technical support representative " "and arrange to have the hardware keystore on the supervisor " "card replaced." KEYSTORE_AE46C1-6-RANDOM 6-Information A pseudo-random number was generated twice in succession[dec]. A pseudo-random number generator produced the same number twice\n\ in succession. - "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." KEYSTORE_AE46C1-6-RANDOM 6-Information A pseudo-random number was generated twice in succession[dec]. A pseudo-random number generator produced the same number twice\n\ in succession. - "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." KEYSTORE_AE46C1-6-RANDOM 6-Information A pseudo-random number was generated twice in succession[dec]. A pseudo-random number generator produced the same number twice\n\ in succession. - "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." KEYSTORE_AE46C1-6-RANDOM 6-Information A pseudo-random number was generated twice in succession[dec]. A pseudo-random number generator produced the same number twice\n\ in succession. - "Under normal circumstances a pseudo-random number generator will\n\ occasionally produce the same number twice in succession and this\n\ is not a problem. However if this message occurs frequently the \n\ system should be manually reloaded. If the message is persistent \n\ across reloads copy the error message exactly as it appears and \n\ report it to your technical support representative." KEYSTORE_AE46C1-6-SELF_TEST_PASS 6-Information Keystore pass power on self test keystore pass power on self test for both SHA1 and HMAC-SHA1 - - KEYSTORE_AE46C1-6-SELF_TEST_PASS 6-Information Keystore pass power on self test keystore pass power on self test for both SHA1 and HMAC-SHA1 - - KEYSTORE_AE46C1-6-SELF_TEST_PASS 6-Information Keystore pass power on self test keystore pass power on self test for both SHA1 and HMAC-SHA1 - - KEYSTORE_AE46C1-6-SELF_TEST_PASS 6-Information Keystore pass power on self test keystore pass power on self test for both SHA1 and HMAC-SHA1 - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-BAD_MAGIC 3-Error Bad magic number 0x%08x in software keystore file \[chars]\. Keystore data file appears to have been corrupted. Keys can not be retrieved from persistent memory. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_R 3-Error Failed to open file \[chars]\ for reading software keystore. [chars] An error occurred while opening the keystore file for reading. CTS keys could not be retrieved. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_OPEN_W 3-Error Failed to open file \[chars]\ for writing software keystore. [chars] An error occurred while opening a file for persistent storage. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_READ 3-Error An error [chars] occurred while reading from the software CTS keys could not be retrieved from persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IFS_WRITE 3-Error An error occurred while writing to the software keystore file. CTS keys could not be saved to persistent storage. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPC_NO_PROC 3-Error Could not create a process to receive keystore redundancy messages. An error was encountered when trying to create a process to handle incoming keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCNOCONN 3-Error No IPC communication path to peer available for keystore [chars]. No IPC connection to the peer was available for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCOPEN 3-Error Failed to open IPC port to peer for keystore redundancy: [chars] An error was encountered when trying to open an IPC port for keystore redundancy messages. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCPORT 3-Error Failed to create IPC port [chars] for keystore redundancy. [chars]. An error was encountered when trying to create an IPC port. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-IPCSEND 3-Error IPC send error [chars] while sending [chars]. An error occurred while sending an IPC message to the peer during a keystore redundancy operation. This means that any updates made to the ACTIVE keystore cannot be pushed to the STANDBY keystore. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-ISSU_INCOMPAT 3-Error Standby incompatible for SSO. The image on the standby failed ISSU message version negotiation. As a result we will not be able to sync keystore updates to it and so it is disallowed from reaching \hot\ standby status in SSO mode. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-NO_KEYSTORE 3-Error CTS hardware keystore is not responsive and software emulation is not enabled. The CTS hardware keystore on the switch has failed and needs to be inspected.\n Since CTS credentials are stored in the keystore this means that CTS authentication and authorization operations will fail. \n The following action is recommended: If the defect is shown on the Active Supervisor try to switchover to Standby Supervisor. If the defect is shown on Standby Supervisor try to reset the Standby. If the defect persists there may be damage to the hardware keystore chip please take appropriate action. In the meantime you can configure the switch to use software keystore emulation. After you have enabled software keystore emulation please re-configure CTS credentials to populate the software keystore. - - KEYSTORE-3-SESSION 3-Error KeyStore ISSU client [chars] KeyStore ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up. - "show issu capability entries and " "show issu session and " "show issu negotiated capability " KEYSTORE-3-SESSION 3-Error KeyStore ISSU client [chars] KeyStore ISSU client observed an error during a session negotiation with the peer unit. When there is a problem with the session the standby unit can not be brought up. - "show issu capability entries and " "show issu session and " "show issu negotiated capability " KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KEYSTORE-3-UNEXPECTED_EOF 3-Error Unexpected end of file while reading software keystore \[chars]\. Keystore data file appears to have been truncated. One or more keys can not be retrieved from persistent memory. - - KINEPAK-3-CONTIGUOUS 3-Error Contiguous packet sent for transmit A software error occurred resulting in an unexpected packet being\n\ set up for transmission and the packet was dropped. - LOG_STD_RECUR_ACTION KINEPAK-3-ERR_DSPWARE_DNLD 3-Error dsp[dec] cannot download dspware [chars] A software error occurred resulting in failure to download a \n\ dspware component. - LOG_STD_ACTION KINEPAK-3-ERR_DSPWARE_IMG 3-Error Cannot find dspware [chars] component A software error occurred resulting in failure to download a \n\ dspware component. - LOG_STD_ACTION KINEPAK-3-NODSPENTRY 3-Error No dsp entry in dsp list The software structure that is used to maintain the DSP \n\ instance is missing. - LOG_STD_RECUR_ACTION KINEPAK-3-NOMAILELEMENTS 3-Error Cannot create message buffer A software error occurred resulting in failure to create a \n\ message buffer to send messages among processes. - LOG_STD_ACTION KINEPAK-3-NOPARTICLE 3-Error No particle available for ingress packet A software error occurred resulting in failure to obtain a \n\ particle to hold an ingress packet from DSP. - LOG_STD_RECUR_ACTION KINEPAK-3-NOPARTICLEPOOL 3-Error Cannot create particle pool A software error occurred resulting in failure to create a \n\ particle pool to receive packets from DSP. - LOG_STD_ACTION KINEPAK-3-NORXPAK 3-Error Static receive paktype unavailable A software structure was found in an unexpected state during\n\ run-time for the indicated DSP. - LOG_STD_ACTION L2BD_PROXY-2-PROXY_IPC_INIT_FAILED 2-Critical QFP L2BD Proxy IPC interface initialization failure result: [dec]. Cisco internal software error. QFP L2BD Proxy initialization detected that the IPC interface initialization failed. QFP L2BD proxy will not be functional while this condition exists. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-3-L2BD_MEM_EXTEND_FAILED 3-Error L2BD IPC subtype: [dec] Extending memory failed. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-3-L2BD_MEM_REQ_FAILED 3-Error L2BD IPC subtype: [dec] Requesting more memory failed. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-3-PROXY_BAD_MSG 3-Error QFP L2BD Proxy received bad length message type [dec] Cisco internal software error. QFP L2BD Proxy received a corrupted message from control plane. This message will be ignored. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-3-PROXY_IPC_ALLOC_FAILED 3-Error QFP L2BD Proxy [chars] message lost due to message buffer allocation failure. Cisco internal software error. QFP L2BD Proxy message processing detected a message buffer allocation failure. The message is lost as the result of this condition. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-3-PROXY_IPC_SEND_FAILED 3-Error QFP L2BD Proxy [chars] message lost due to message sent failure result: [dec]. Cisco internal software error. QFP L2BD Proxy message processing detected a message sent failure. The message is lost as the result of this condition. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-4-PROXY_INVALID_MSG 4-Warning QFP L2BD Proxy received invalid message type [dec] Cisco internal software error. QFP L2BD Proxy received an invalid message from control plane. This message will be ignored. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2BD_PROXY-4-PROXY_INVALID_MSG_LEN 4-Warning QFP L2BD Proxy IPC invalid length [dec]:[dec] len [dec] flags 0x[hec] source [dec] Cisco internal software error. QFP L2BD Proxy received invalid IPC message length from control plane. This message will be ignored. qfp-l2bd keyword:l2bd LOG_STD_ACTION L2CAC-5-VC_BW_NOT_ENOUGH 5-Notice VC [dec]/[dec] bandwidth is not enough to add this Trunk portchannel. Total bandwidth is [dec] cps but requires [dec] cps to add this Trunk portchanel VC bandwidth is not enough Need to increase the bandwidth . - "To support this call VC bandwidh the sustained cell rate has to be increased to accomidate the new calls." L2CAC-5-VC_BW_NOT_ENOUGH 5-Notice VC [dec]/[dec] bandwidth is not enough to add this Trunk portchannel. Total bandwidth is [dec] cps but requires [dec] cps to add this Trunk portchanel VC bandwidth is not enough Need to increase the bandwidth . - "To support this call VC bandwidh the sustained cell rate has to be increased to accomidate the new calls." L2CTRL-3-ADD_REGISTRY_FAILED 3-Error Subsystem [chars] fails to add callback function [chars] Other subsystem must have mistakenly add its own callback functions. This syslog is for debugging purpose. l2ctrl LOG_STD_NO_ACTION L2FIB-3-BAD_PARAM 3-Error [chars] Invalid parameter l2fib LOG_STD_ACTION L2FIB-3-EVPN_ERROR 3-Error [chars] EVPN encap error l2fib LOG_STD_ACTION L2FIB-3-IMET_ENCAP_MISMATCH 3-Error IMET Encapsulation Mismatch on bridge domain [dec] from [chars] - - - L2FIB-3-IMET_REPTYPE_MISMATCH 3-Error IMET Replication Mismatch on bridge domain [dec] from [chars] Local is Static - l2fib LOG_STD_ACTION L2FIB-3-MAC_ENCAP_MISMATCH 3-Error MAC [chars] Encapsulation Mismatch on bridge domain [dec] from [chars] Incompatible Encapsulation Type in MAC/IP Route RT-2 received from remote peer l2fib LOG_STD_ACTION L2FIB-3-MAC_ERROR 3-Error MAC address [chars] is reserved for [chars] output list bit is produced by [chars] on bridge domain [dec] - l2fib LOG_STD_ACTION L2MC_QUERIER-4-NO_IP_ADDR_CFG 4-Warning The [chars] querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system. The allocation of explicit-tracking entries is bounded to avoid\n\ the IGMP/MLD snooping hogs the system resources igmp/mld snooping "Disable and re-enable L2 multicast snooping on the VLAN." L2MC_QUERIER-4-NO_IP_ADDR_CFG 4-Warning The [chars] querier cannot send out General Query messages in VLAN [dec] because there is no IP address configured on the system. An IP address should be specified for the IGMP/MLD querier either at the global or per VLAN level. l2mcast "Configure a source IP address for the IGMP/MLD querier. " L2MC_QUERIER-4-PIM_ENABLED 4-Warning The [chars] querier is operationally disabled in VLAN [dec] because PIM has been enabled on the SVI. PIM has been detected on the SVI. The IGMP/MLD querier function should not be operationally enabled when PIM is enabled on the SVI. l2mcast "Ensure that PIM is disabled on the SVI. " L2MC_QUERIER-4-PIM_ENABLED 4-Warning The [chars] querier is operationally disabled in VLAN [dec] because multicast router interface has been enabled on the SVI. multicast router interface has been detected on the SVI. The IGMP/MLD querier function should not be operationally enabled when multicast router interface is enabled on the SVI. l2mcast "Ensure that multicast router interface is disabled on the SVI. " L2MC_QUERIER-4-SAME_SRC_IP_ADDR 4-Warning An [chars] General Query packet with the same source IP address [chars] The querier has received an IGMP/MLD General Query message with a source IP address identical to that configured for the IGMP/MLD querier itself. This is considered a network configuration error. l2mcast "Check IGMP/MLD querier source IP address configuration on the router " "or switch connected via the port identified." "Ensure unique source IP addresses are configured on each system. " L2MC_QUERIER-4-SNOOPING_DISABLED 4-Warning The [chars] querier is operationally disabled in VLAN [dec] because [chars] snooping has been disabled in this VLAN. IGMP/MLD snooping has been detected as being disabled on this VLAN. The IGMP/MLD querier function should not be operationally enabled when IGMP/MLD snooping is disabled. l2mcast "Ensure that IGMP/MLD snooping is enabled globally and on the VLAN " "reported. " L2MC_QUERIER-4-SNOOPING_DISABLED 4-Warning The [chars] querier is operationally disabled in VLAN [dec] because [chars] snooping has been disabled in this VLAN. IGMP/MLD snooping has been detected as being disabled on this VLAN. The IGMP/MLD querier function should not be operationally enabled when IGMP/MLD snooping is disabled. l2mcast "Ensure that IGMP/MLD snooping is enabled globally and on the VLAN " "reported. " L2MC_QUERIER-4-ZERO_SRC_IP_ADDR 4-Warning An [chars] General Query packet with source IP address that contained all zeroes is received in VLAN [dec] on port [chars]. The IGMP/MLD querier has received an IGMP/MLD General Query message with a source IP address that contained all zeroes. Some IGMP/MLD clients cannot process General Query with source IP address that contained all zeroes. l2mcast "Check the source IP address of the IGMP/MLD querier that is on the router " "or switch connected to the port specified in the message. " L2MC_QUERIER-6-PIM_DISABLED 6-Information The [chars] querier is now operationally enabled in VLAN [dec] because PIM is no longer enabled on the SVI. PIM has been disabled on the SVI and as a result the IGMP/MLD querier function has now been enabled. l2mcast "No action is required." L2MC_QUERIER-6-PIM_DISABLED 6-Information The [chars] querier is now operationally enabled in VLAN [dec] because multicast router interface is no longer enabled on the SVI. multicast router interface has been disabled on the SVI and as a result the IGMP/MLD querier function has now been enabled. l2mcast "No action is required." L2MC_QUERIER-6-SNOOPING_ENABLED 6-Information The [chars] querier is now operationally enabled in VLAN [dec] because [chars] snooping is no longer disabled. IGMP/MLD snooping has now been enabled and as a result the IGMP/MLD querier function has now been enabled. l2mcast "No action is required." L2MC_QUERIER-6-SNOOPING_ENABLED 6-Information The [chars] querier is now operationally enabled in VLAN [dec] because [chars] snooping is no longer disabled. IGMP/MLD snooping has now been enabled and as a result the IGMP/MLD querier function has now been enabled. l2mcast "No action is required." L2MC_QUERIER-6-SWITCHOVER_NOTIFICATION 6-Information The [chars] querier is now operationally enabled in VLAN [dec] because switchover has occured. Switchover has occured and the IGMP/MLD querier function has now been enabled. l2mcast "No action is required." L2MCAST_WIRELESS_ISSU-2-GET_BUFFER 2-Critical L2mcast Wireless ISSU client failed to get buffer for message. Error: [dec] [chars] The L2mcast Wireless ISSU client failed to get buffer space for building a negotiation message. A negotiation message cannot be sent to the standby device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ewlc-multicast "show logging and show checkpoint client" L2MCAST_WIRELESS_ISSU-2-INIT 2-Critical L2mcast Wireless ISSU client initialization failed to [chars]. Error: [dec] [chars] The L2mcast Wireless ISSU client could not be initialized. This initialization failure must be addressed before in-service software upgrade or downgrade can be performed successfully. If you do not address this failure there will be downtime during software upgrade or downgrade. ewlc-multicast LOG_STD_ACTION L2MCAST_WIRELESS_ISSU-2-SEND_NEGO_FAILED 2-Critical L2mcast Wireless ISSU client failed to send negotiation message. Error: [dec] [chars] The L2mcast Wireless ISSU client failed to send a session negotiation message to the peer device. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ewlc-multicast "show logging and show checkpoint client" L2MCAST_WIRELESS_ISSU-2-SESSION_NEGO 2-Critical L2mcast Wireless ISSU client encountered unexpected client nego_done. Error: [dec] [chars] An ISSU-compliant client transitions through a series of internal states. The L2mcast Wireless ISSU client encountered a 'client negotiation done' state that was unexpected. If a problem occurs with the ISSU session negotiation the standby device cannot be brought up properly. ewlc-multicast "show issu session and " "show issu negotiated capability " L2MCAST_WIRELESS_ISSU-2-SESSION_REGISTRY 2-Critical L2mcast Wireless ISSU client failed to register session information. Error: [dec] [chars] The L2mcast Wireless ISSU client failed to register session information. If a problem occurs with the ISSU session registration the standby device cannot be brought up properly. ewlc-multicast "show issu capability entries and " "show issu session and " "show issu negotiated capability " L2MCAST_WIRELESS_ISSU-3-INVALID_SESSION 3-Error L2mcast Wireless ISSU client does not have a valid registered session. The L2mcast Wireless ISSU client does not have a valid registered session. ewlc-multicast "show issu capability entries and " "show issu session and " "show issu negotiated capability " L2MCAST_WIRELESS_ISSU-3-MSG_NOT_OK 3-Error L2mcast Wireless ISSU client 'Message Type [dec]' is not compatible The L2mcast Wireless ISSU client received an incompatible message from the peer device. The message cannot be processed. ewlc-multicast "show issu message group and " "show issu session and " "show issu negotiated version " L2MCAST_WIRELESS_ISSU-3-MSG_SIZE 3-Error L2mcast Wireless ISSU client failed to get the MTU for Message Type [dec]. Error: [dec] [chars] The L2mcast Wireless ISSU client failed to calculate the MTU for the specified message. The L2mcast Wireless ISSU client is not able to send the message to the standby device. ewlc-multicast "show issu message group and " "show issu session and " "show issu negotiated version " L2MCAST_WIRELESS_ISSU-3-SESSION_UNREGISTRY 3-Error L2mcast Wireless ISSU client failed to unregister session information. Error: [dec] [chars] The L2mcast Wireless ISSU client failed to unregister session information. ewlc-multicast "show issu session and " "show issu negotiated capability " L2MCAST_WIRELESS_ISSU-3-TRANSFORM_FAIL 3-Error L2mcast Wireless ISSU client [chars] transform failed for 'Message Type [dec]'. Error: [dec] [chars] The L2mcast Wireless ISSU client could not transform the specified message type. If the transmit transformation failed the checkpoint message was not sent to the standby device. If the receive transformation failed the checkpoint message was not applied on the standby device. In both cases the L2mcast Wireless state between the active device and the standby device is not identical. ewlc-multicast "show issu session and " "show issu negotiated version " L2TM-3-ACCESS_ERR 3-Error Tcam access failed while [chars] Failed to read/write from/to tcam. hardware LOG_STD_ACTION L2TM-7-INTERNAL_ERR 7-Debug Internal error: [chars] An internal error occured. firmware LOG_STD_ACTION L2TP_HA -3-ISSU 3-Error [chars]: [chars] A L2TP ISSU error occurred. l2tp LOG_STD_SH_TECH_ACTION L2TP_HA -3-SYNC 3-Error [chars]: code [dec] An error occurred when syncing L2TP state to the Standby Route Processor. This may affect Non-Stop Forwarding capability on L2TP-based interfaces during and after switchover until the state is recovered through normal protocol operation. fr "Reset the standby processor to attempt the sync again. " LOG_STD_RECUR_ACTION L2TP-3-CRITICAL 3-Error [chars] An critical event has been processed by the L2TP subsystem. L2TP LOG_STD_NO_ACTION L2TP-3-ILLEGAL 3-Error [chars]: [chars] An illegal event has been processed by the L2TP subsystem. L2TP LOG_STD_NO_ACTION L2TP-5-IGNOREICMPMTU 5-Notice Ignoring received ICMP Type 3 Code 4 due to pmtu min or max setting An ICMP Type 3 Code 4 fragmentation needed and DF set packet L2TP "If you want the ICMP packet to be accepted and used to " "decrease or increase the MTU then use the " "vpdn pmtu min command to " "decrease the minimum MTU allowed and enter the " " vpdn pmtu max command to " "increase the maximum MTU that is allowed. The minimum value " "specified is the minimum MTU that is allowed and the " "maximum value specified is the maximum MTU that is " "allowed." L2TPV3_NP_CLIENT-3-INFO 3-Error [chars] L2TPv3 NP Client failed to initialize properly which will result in\n\ improper operation of l2tpv3 feature vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." L2TPV3_NP_CLIENT-3-NOMEM 3-Error [chars] L2TPv3 NP Client failed to initialize properly which will result in\n\ improper operation of l2tpv3 feature vsp-mid "This error may indicate that more memory must be installed on the\n\ affected card or platform in order to service all the features and\n\ related entities enabled via the configuration.\n\\n\ Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." L2TPV3_NP_CLIENT-4-WARN 4-Warning [chars] [dec] [chars] L2TPv3 Entry could not be added because:\n\ 1. Entry passed is invalid. vsp-mid "Try to reload the IOS image on the affected card or platform. If the\n\ error persists record the output from the following commands:\n\\n\ show tech \n\ show log \n\ Provide this information to your technical support\n\ representative." L2TUN-3-ILLEGAL 3-Error [chars] An illegal event has been processed by the L2TUN subsystem. L2TUN LOG_STD_NO_ACTION L2VPN_GLOBAL_OP-5-XCONNECT 5-Notice ERRMSG_NOFLAGS - - - L2VPN_GLOBAL_OP-5-XCONNECT 5-Notice ERRMSG_NOFLAGS - - - L3MM-4-AP_DB_ADD 4-Warning Failed to add AP to DB { AP: [enet] [inet]} The L3MM failed to add the entry for the specified AP into the AP database cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-4-AP_DB_DEL 4-Warning Failed to delete AP from DB { AP: [enet] [inet]} The L3MM failed to initialize due to the specified reason cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-4-DUP_AP_IPADDR 4-Warning AP [enet] is requesting ip [inet] which is being used by another AP The L3MM detected that an access point requested an IP address that is being used by another access point in the network. - "Change the IP address of one of the two access " "points" L3MM-4-DUP_IPADDR 4-Warning MN [enet] is requesting ip [inet] which is being used by MN [enet] The L3MM detected that a mobile node requested an IP address that is being used by another mobile node in the network. - "Change the IP address of one of the two mobile " "nodes" L3MM-4-MALLOC_FAIL 4-Warning Memory allocation failure [chars] The L3MM failed to allocate memory which was needed to perform a given operation and/or respond to an event - "Increase the memory on the RP of the supervisor" L3MM-4-MN_IPDB_ADD 4-Warning Failed to add MN to MN DB { MN: [enet] [inet]} The L3MM failed to add the entry for the specified MN into the MN IP database cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-4-MN_IPDB_DEL 4-Warning Failed to delete MN from IP DB { MN: [enet] [inet]} The L3MM failed to delete the entry for the specified MN from the MN IP database cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-4-MN_MACDB_ADD 4-Warning Failed to add MN to MAC DB { MN: [enet] AP: [inet] } The L3MM failed to add the entry for the specified MN into the MN MAC database cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-4-MN_MACDB_DEL 4-Warning Failed to delete MN from MAC DB { MN: [enet] [inet] AP: [inet] WNID: [dec] } The L3MM failed to delete the entry for the specified MN from the MN MAC database cat6000-wireless "Copy the error message exactly as it appears and report it to your " "technical support representative." L3MM-5-WLAN 5-Notice Wireless LAN Module in slot [dec] is [chars] The L3MM detected a change in the state of the Wireless LAN module in the specified slot. If the module is now on line L3MM starts accepting access-point and mobile-node registrations from the WDS on the module. If the module is now off line L3MM purges all access points and mobile nodes received from the module. - LOG_STD_NO_ACTION L3MM-5-WLAN_COMM_ABORT 5-Notice Communication with Wireless LAN Module in slot [dec] aborted [chars] The Layer 3 Mobility Manager detected communication failure with the Wireless LAN module specified in the error message above and will respond as if the module went offline by purging its access point and mobile node databases. However the module will not be reset by the Layer 3 Mobility Manager - LOG_STD_NO_ACTION L3MM-5-WLAN_PWR_DN 5-Notice Wireless LAN Module in slot [dec] will be powered down another module is already active The L3MM detected a Wireless LAN module trying to come online while another module was already functional as the active Wireless LAN module. The L3MM does not support more than one Wireles LAN module online in the chassis at a given time which is why this module will be powered down - LOG_STD_NO_ACTION L3TCAM-3-SIZE_CONFLICT 3-Error [chars] requires enabling extended routing In order to support this feature TCAM entry needs to be configured to extended routing enable. firmware "Modify the Switch Database Management SDM " "template to enable the switch to support the " "144-bit Layer 3 TCAM. Use the sdm prefer " "extended-match sdm prefer access extended-match " "or sdm prefer routing extended-match global " "configuration command and then reload the switch " "by using the reload privileged EXEC command." L3TCAM-3-TOO_MANY_VRF 3-Error Exceed the maximum number of VRF allowed The number of VPN exceeds the maximum number of allowed VPN routing/forwarding table on this hardware platform. firmware "Reconfigure your switch to limit the number " "of VRFs. Do not define name more than seven " L4_INSPECT-3-INVALID_CHUNK_ID 3-Error Invalid chunk ID for protocol [dec] Failed to determine chunk ID for specified protocol. Unable to free CFT feature object. qfp-cxsc LOG_STD_ACTION L4-3-HA_INVALID_MSG_LEN_RCVD 3-Error invalid [chars] rg [dec] [dec] expected [dec] opcode [chars] [hec] Standby received an invalid Firewall HA message cpp-ucode LOG_STD_ACTION L4-3-HA_INVALID_MSG_RCVD 3-Error invalid [chars] [hec] expected [hec] opcode [chars] [hec] Standby received an invalid Layer 4 HA message cpp-ucode LOG_STD_ACTION L4F-2-INVALIDFLOW 2-Critical Invalid L4F flow: 0x[hec] An invalid L4F flow entry was detected. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-2-INVALIDFLOW 2-Critical Invalid L4F flow: 0x[hec] An invalid L4F flow entry was detected. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-2-SEMLOCKFAILURE 2-Critical Cannot lock TCP semaphore on flow 0x[hec] with tcb 0x[hec] Cannot obtain the semaphore lock for a TCB we expect to be able to lock. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-2-SEMLOCKFAILURE 2-Critical Cannot lock TCP semaphore on flow 0x[hec] with tcb 0x[hec] Cannot obtain the semaphore lock for a TCB we expect to be able to lock. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-4-L4F_REINJECT_HANDLE_ERROR 4-Warning L4F reinject [chars] L4F reinjection handle creation or update failed. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-4-L4F_REINJECT_HANDLE_ERROR 4-Warning L4F reinject [chars] L4F reinjection handle creation or update failed. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-5-NOBUFFER 5-Notice Cannot allocate buffer to send data on the flows [chars]:[dec] -> [chars]:[dec] A buffer could not be allocated while trying to send data on the\n\ indicated flow. The issue could be due to low or fragmented memory.\n\ If the memory issue doesn't resolve automatically it could result\n\ in connection resets. layer4-forwarding "This is an informational message that potential points to low or\n\ fragmented memory which could happen if the router is running beyond\n\ its resource limits. Check the number of flows and the traffic rate\n\ going through the router and contact your technical support\n\ representative with that info for assistance." L4F-5-NOBUFFER 5-Notice Cannot allocate buffer to send data on the flows [chars]:[dec] -> [chars]:[dec] A buffer could not be allocated while trying to send data on the\n\ indicated flow. The issue could be due to low or fragmented memory.\n\ If the memory issue doesn't resolve automatically it could result\n\ in connection resets. layer4-forwarding "This is an informational message that potential points to low or\n\ fragmented memory which could happen if the router is running beyond\n\ its resource limits. Check the number of flows and the traffic rate\n\ going through the router and contact your technical support\n\ representative with that info for assistance." L4F-6-L4F_FLOW_CREATION_FAILED 6-Information L4F flow creation failed [chars] L4F flow entry creation failed due to an error. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-6-L4F_FLOW_CREATION_FAILED 6-Information L4F flow creation failed [chars] L4F flow entry creation failed due to an error. layer4-forwarding "If this message recurs copy it down exactly as it appears and contact\n\ your technical support representative for assistance." L4F-6-L4F_FLOW_LIMIT_EXCEED 6-Information L4F flow limit was exceeded:[dec] This is an informational message. L4F flow max limit was exceeded. layer4-forwarding "Issue the" "show l4f statistics command and " "contact your technical support representative and \n\ provide the representative with the gathered information." L4F-6-L4F_FLOW_LIMIT_EXCEED 6-Information L4F flow limit was exceeded:[dec] This is an informational message. L4F flow max limit was exceeded. layer4-forwarding "Issue the" "show l4f statistics command and " "contact your technical support representative and \n\ provide the representative with the gathered information." LABEL_ALLOC_FAIL-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - LABEL_ALLOC_FAIL-3-ATOM_TRANS 3-Error ERRMSG_NOFLAGS - - - LABEL_REGION-3-LCON 3-Error ERRMSG_NOFLAGS - - - LABEL_REGION-3-LCON 3-Error ERRMSG_NOFLAGS - - - LANCE-1-INITFAIL 1-Alert msgtxt_initfail The hardware failed to initialize correctly. - "Repair or replace the controller." LANCE-1-MEMERR 1-Alert msgtxt_memoryerror An Ethernet interface detected a hardware problem. - "Repair or replace the controller." LANCE-3-BADCABLE 3-Error msgtxt_badcable Ethernet cable is not connected. - "Check Ethernet cable connection." LANCE-3-BADUNIT 3-Error msgtxt_badunit An internal software error occurred. - "If either message recurs call your technical support representative\n\ for assistance." LANCE-3-OWNERR 3-Error msgtxt_ownerror An Ethernet interface is malfunctioning or an internal software error\n\ occurred. - "Repair or replace the controller." LANCE-3-SPURIDON 3-Error Unit [dec] spurious IDON interrupt csr[dec]=0x%04x An Ethernet interface generated a spurious Initialization Done\n\ interrupt. - "Repair or replace the controller." LANCE-3-UNDERFLO 3-Error Unit [dec] underflow error The Ethernet hardware is requesting data faster than the system can\n\ supply it. This condition might indicate that the system is at the\n\ limit of its performance. - "A small number of underflows might not be a cause for concern. You can\n\ monitor underflows with the show interface command. Reducing the load\n\ on the router or installing a higher-performance router should\n\ alleviate this problem." LANCE-4-BABBLE 4-Warning Unit [dec] babble error csr0 = 0x[hec] An Ethernet interface is malfunctioning. - "Determine whether the malfunction stems from a software or hardware\n\ error by turning off all fastswitching.\n\\n\ Error messages showing that the packet is too large for the link\n\ indicate a software error at a high level.\n\\n\ Copy the error message exactly as it appears and report it to your\n\ technical support representative.\n\\n\ Receiving no error messages indicates a hardware error. \n\\n\ Repair or replace the controller." LANCE-5-COLL 5-Notice Unit [dec] excessive collisions. TDR=[dec] - - "If the transceiver appears to be properly terminated repair or\n\ replace the Ethernet interface card." LANCE-5-LATECOLL 5-Notice Unit [dec] late collision error An Ethernet transceiver is malfunctioning the Ethernet is overloaded\n\ or the Ethernet cable is too long. - "Repair or replace the controller." LANCE-5-LOSTCARR 5-Notice Unit [dec] lost carrier. Transceiver problem? An Ethernet transceiver is unplugged or faulty. - "Repair or replace the controller." LANE-3-BADILMI 3-Error Unexpected ILMI event [dec] An internal error occurred. - "This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration." LANE-3-BADNAME 3-Error ELAN name must be 1-32 characters long A name which is longer than 32 characters identifying a LANE \n\ component has been entered by the user. - "Re-enter a shorter name." LANE-3-BADTYPE 3-Error Inappropriate LAN type An unexpected LAN type has been specified for a LANE component.\n\ Only ethernet and token-ring elans are supported. - "Specify a valid LAN type." LANE-3-LANE_ERROR 3-Error [chars] An internal error has occured which reflects an inconsistency\n\ in the system and needs attention. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LANE_SIG_ERR 3-Error [chars] An internal error occurred while system routines were handling ATM\n\ signaling messages for LANE. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LEC_BAD_CTL_DIST_TYPE 3-Error [chars] CTL DIST blli type wrong Wrong BLLI value specified on the incoming circuit. - "The originator of the circuit is not using the correct BLLI value\n\ for this type of circuit. LANE standard defines these values and\n\ the originator is violating the standard." LANE-3-LEC_BADAD 3-Error [chars] LEC unable to compute ATM address The client cannot obtain an ATM address from the given configuration\n\ or auto-assignment failed to get an ATM prefix from the switch. - - LANE-3-LEC_CFG 3-Error [chars] CFG_REQ failed [chars] LECS returned [dec] The master LECS refused the LEC's configuration request. - "Check your LECS configurations." LANE-3-LEC_CONTROL_MSG 3-Error Received bad control message on interface [chars] The LANE client received an unexpected or inappropriate control message \n\ over one of its vc's. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LEC_ERR 3-Error [chars] A LANE client software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LEC_JOIN 3-Error [chars] JOIN failed [chars] LES returned [dec] LANE client was rejected the Join request to join its elan. - "This is usually because of user configuration errors: LANE client\n\ attempting to join an incorrect elan or elan not configured\n\ in the LES or validation failures with the LECS etc..." LANE-3-LEC_LISTEN 3-Error [chars] listen failed on [chars] The LANE client could not register its address with ATM signalling\n\ to be able to accepts calls on that address. - "Reconfigure the client ATM address. It may be conflicting with another\n\ component with the same ATM address." LANE-3-LEC_RD_REGISTER 3-Error [chars] RD REGISTER failed for Route Descriptor [hec] A software or hardware error occurred. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LEC_REGISTER 3-Error [chars] REGISTER failed [chars] LES returned [dec] attempt to register a mac-atm address binding with LES failed. - "The LES has already registered the requested mac addr - atm addr binding." LANE-3-LEC_SIGNAL 3-Error Unexpected SigAPI event [dec] ATM signaling sent the LANE client an unexpected message type. - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-3-LEC_WRONG_ELAN_ID 3-Error [chars]: elan id mismatch: LECS indicates [dec] LES indicates [dec] The elan-id returned by LES does not match the value given by LECS or\n\ via the CLI - "Check configuration of elan ids specified in the LECS database and\n\ the LES. The mismatch must be occuring as a result of misconfiguration." LANE-3-LECS_ERROR 3-Error MSG_TRACEBACK | MSG_PROCESS - - - LANE-3-LES_ERROR 3-Error [chars] A serious internal occured with LES/BUS. - "This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration." LANE-3-LSV_BADAD 3-Error [chars] elan [chars] unable to compute [chars] ATM address - - "Enter a correct ATM address template for the LANE component \"BUS\"\n\ \"server\" or \"config server\" named in the error message." LANE-3-LSV_CRASH 3-Error [chars] elan [chars] unrecoverable error [chars] A very serious LES/BUS internal error occurred. - "This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration." LANE-3-NAMECHG 3-Error A LANE Client is already running here using another elan name Both the LANE client and the LANE server/BUS may have an emulated LAN\n\ name specified in the configuration via the lane server-bus and lane\n\ client commands. If both specify the emulated LAN name then the name\n\ cannot be changed by re-entering just one of the commands. - "Use the no lane server-bus command to delete the server-bus or the no\n\ lane client command to delete the client. Then the other of the two\n\ commands can be re-entered with another emulated LAN name. Finally\n\ re-enter the deleted command with the new emulated LAN name." LANE-3-NOILMI 3-Error ILMI service registration failed - - "This error should not occur. Download the system error log then call\n\ your technical support representative and provide the log the error\n\ message and the router configuration." LANE-3-NOINT 3-Error [chars] still destroying old sub-interface An attempt was made to create a new subinterface while a previous\n\ version of the subinterface was still being destroyed. - "Wait a minute and try again. If failure still occurs try shutting\n\ down the main interface. Rebooting may be required to recover in\n\ extreme cases." LANE-3-NOREGILMI 3-Error [chars] [chars] cannot register %Cj with ILMI An attempt to register the given ATM address with the ATM switch\n\ failed. This failure can occur because the ATM switch is down or\n\ misconfigured. The registration will be retried. - "If the situation persists after a number of attempts and the switch\n\ is up the configuration of the switch and router should be examined. A \n\ likely cause is that the ATM address being registered is not\n\ compatible with the parameters configured in the switch. Correct the configuration." LANE-3-TYPECHG 3-Error A LANE Client is already running here using another elan type - - "Use the no lane server-bus command to delete the server-bus or the no\n\ lane client command to delete the client. Then the other of the two\n\ commands can be re-entered with a new type. Finally re-enter the\n\ deleted command with the new type." LANE-4-LECS_WARNING 4-Warning [chars] - - "Copy the error message exactly as it appears and report it to your\n\ technical support representative." LANE-4-LSV_ADDR 4-Warning [chars] elan [chars] unable to register LES/BUS ATM addr LANE Server or BUS could not register its address with ILMI. - "Try and investigate why. Some of the reasons are: user defined\n\ override address does not conform to the switch prefix or that\n\ there is a problem with the ATM switch with whom the entity is \n\ registering." LANE-4-LSV_LECID 4-Warning [chars] elan [chars] LECIDs exhausted The LANE server specified has 65279 clients. No more can be added. - "Change the configurations to avoid trying to have more than 65279 LANE\n\ clients on this server." LANE-5-UPDOWN 5-Notice [chars] [chars] [chars]: [chars] changed state to [chars] A LANE component changed state to up/down. - "If this event is expected then take no action. Otherwise\n\ please contact a technical support representative." LANE-6-INFO 6-Information [chars] LANE subsystem simple informational messages. - "None." LANE-6-LEC_INFO 6-Information [chars] LANE client informational messages. - "None." LANE-6-LECS_INFO 6-Information [chars] Simple informational LECS messages. - "None." LANE-6-LES_INFO 6-Information [chars] Simple informational LES messages. - "None." LANMGR-2-NOMEMORY 2-Critical No memory available: [chars] The requested operation failed because of a low memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." LANMGR-4-BADRNGNUM 4-Warning Ring number mismatch on [chars] shutting down the interface - - "Check all bridges connected to this Token Ring and ensure that they\n\ are using the same assigned ring number." LANMGR-4-BADUPCALL 4-Warning Unexpected call [chars] from LLC2 for Bridge %03x-[hec]-%03x An internal software error occurred. - LOG_STD_RECUR_ACTION LANMGR-4-NORING 4-Warning No ring info for [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION LANMGR-4-OLDTRAMON 4-Warning Cannot run RPS on [chars] Old TRAMON code. The software on this interface cannot support the functions required\n\ for LAN Network Manager. - "Call your Cisco technical support representative about a\n\ firmware upgrade for this interface card." LAPB-2-NOBUF 2-Critical Interface [chars] no buffer available to [chars] There was insufficient memory for the LAPB protocol engine to send a\n\ message. lapb "This message is acceptable if it occurs infrequently because the LAPB\n\ protocol is designed to handle loss of frames. Frequent occurrences can\n\ cause disruption of service. The system can be configured to ease\n\ memory demands or if conditions warrant the system can be upgraded to\n\ a larger memory configuration." LAPB-3-BADPAYLOAD 3-Error Interface [chars] Invalid payload value: [chars] An internal software error occurred. lapb "If either of these messages recur call your technical support\n\ representative for assistance." LAPB-3-CONTEXTERR 3-Error [chars]: [chars] An internal software error occurred. lapb "If either of these messages recur call your technical support\n\ representative for assistance." LAPB-3-NOINPIDB 3-Error Input idb not set An internal software error occurred. lapb "If either of these messages recur call your technical support\n\ representative for assistance." LAPB-3-NULLPAK 3-Error Interface [chars] NULL packet ptr rvr [dec] vs [dec] vr [dec] An internal software error occurred. lapb "If either of these messages recur call your technical support\n\ representative for assistance." LAPB-3-TIMERERR 3-Error LAPB timer task cannot be created An internal software error occurred. lapb "If either of these messages recur call your technical support\n\ representative for assistance." LAPB-4-CTRLBAD 4-Warning Interface [chars] Invalid control field A received FRMR reported a frame with an invalid control code. lapb "Check the serial line and the devices attached to the line." LAPB-4-FRAMEERR 4-Warning Interface [chars] Frame error: CF [hex] VS [dec] [chars] VR [dec] Reason [hex] - lapb - LAPB-4-INFOBAD 4-Warning Interface [chars] Info field not permitted A received FRMR frame reported that an information field was present\n\ in a frame where no information field is allowed. lapb "Check the serial line and the device attached to the line." LAPB-4-INVNR 4-Warning Interface [chars] Invalid NR value A received FRMR reported a frame with an invalid NR value. lapb "Verify that the equipment attached to the serial line is configured\n\ with the same K value maximum number of outstanding I frames." LAPB-4-N1TOOBIG 4-Warning Interface [chars] N1 too large A received FRMR reported an information frame that was too long. lapb "Verify that the equipment attached to the serial line is configured\n\ with the same N1 value. N1 is in bits and includes the entire frame\n\ plus 16 bits of CRC. However some equipment may require configuration\n\ in octets the omission of the two CRC octets or the omission of the\n\ three octets of LAPB control information." LAPP_OFF-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." LAPP_OFF-1-NOMEMORY 1-Alert msgtxt_nomemory The requested operation could not be accomplished because of a low\n\ memory condition. - "Reduce other system activity to ease memory demands. If conditions\n\ warrant upgrade to a larger memory configuration." LAPP_OFF-2-INTERNAL_ERROR 2-Critical Internal software error [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION LAPP_OFF-2-INTERNAL_ERROR 2-Critical Internal software error [chars] An internal software error occurred. - LOG_STD_RECUR_ACTION LAPP_OFF-2-LAPP_OFF_INTERNAL_ERROR 2-Critical Internal software error [chars] cid=[dec] An internal software error occurred. - LOG_STD_RECUR_ACTION LAPP_OFF-2-LAPP_OFF_INTERNAL_ERROR 2-Critical Internal software error [chars] cid=[dec] An internal software error occurred. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_BAD_MESSAGE 4-Warning LAPP_OFF- Bad message received An unexpected message was received. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_BAD_MESSAGE 4-Warning LAPP_OFF- Bad message received An unexpected message was received. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_NO_SMTP 4-Warning mmsp- Can't connect to the SMTP server No connection was created to the specified SMTP server. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_NO_SMTP 4-Warning mmsp- Can't connect to the SMTP server No connection was created to the specified SMTP server. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_NO_SMTP_SEND 4-Warning FAXMAIL- Could not\n\send data to the SMTP server A connection was made to the SMTP server but no data can be sent. - LOG_STD_RECUR_ACTION LAPP_OFF-4-LAPP_OFF_NO_SMTP_SEND 4-Warning FAXMAIL- Could not\n\send data to the SMTP server A connection was made to the SMTP server but no data can be sent. - LOG_STD_RECUR_ACTION LAPP_OFF-4-SMTP_NOT_CONNECTED 4-Warning SMTP- failed [chars] [dec] A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior. - LOG_STD_NO_ACTION LAPP_OFF-4-SMTP_NOT_CONNECTED 4-Warning SMTP- failed [chars] [dec] A connection attempt to a remote mail server was not successful.\n\ This unexpected behavior. - LOG_STD_NO_ACTION LAPP_OFF-6-LAPP_OFF_CAUSE_ABNORMAL 6-Information Call aborted cause = 0x[hec] Call Aborted due to abnormal error - LOG_STD_NO_ACTION LAPP_OFF-6-LAPP_OFF_CAUSE_ABNORMAL 6-Information Call aborted cause = 0x[hec] Call Aborted due to abnormal error - LOG_STD_NO_ACTION LAPP_OFF-6-SMTP_OPEN 6-Information SMTP- opening [chars] [dec] A connection attempt ... - LOG_STD_NO_ACTION LAPP_OFF-6-SMTP_OPEN 6-Information SMTP- opening [chars] [dec] A connection attempt ... - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_AUTH_FAILED 6-Information User authentication failed Call aborted due to user authentication failure - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_AUTH_FAILED 6-Information User authentication failed Call aborted due to user authentication failure - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED 6-Information Document Media Service DMSP disconnected Call aborted due to Document Media Service DMSP disconnect - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED 6-Information Document Media Service DMSP disconnected Call aborted due to Document Media Service DMSP disconnect - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED_NO_ROUTE 6-Information DMSP - no route - likely - ESMTP client did not connect to remote server Call aborted due to DMSP no route disconnect - likely reason being no ESMTP connection to remote server - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_DMSP_DISCONNECTED_NO_ROUTE 6-Information DMSP - no route - likely - ESMTP client did not connect to remote server Call aborted due to DMSP no route disconnect - likely reason being no ESMTP connection to remote server - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_FMSP_DISCONNECTED 6-Information Fax protocol FMSP disconnected Call aborted due to Fax sessionFMSP disconnect - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_FMSP_DISCONNECTED 6-Information Fax protocol FMSP disconnected Call aborted due to Fax sessionFMSP disconnect - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_INTERNAL 6-Information Internal error occured Call aborted due to an internal error - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_INTERNAL 6-Information Internal error occured Call aborted due to an internal error - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT 6-Information ESMTP client did not connect or lost connection to remote server Call aborted due to loss of outbound ESMTP connection to remote server - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_ESMTP_CONNECT 6-Information ESMTP client did not connect or lost connection to remote server Call aborted due to loss of outbound ESMTP connection to remote server - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_MEMORY 6-Information No memory available Call aborted due to insufficient memory being available - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NO_MEMORY 6-Information No memory available Call aborted due to insufficient memory being available - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NORMAL 6-Information Normal call clearing Call clearing occurred normally - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_NORMAL 6-Information Normal call clearing Call clearing occurred normally - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_VTSP_DISCONNECTED 6-Information Telephony interface VTSP disconnected Call termination due to Telephony interface disconnect - LOG_STD_NO_ACTION LAPP_ON_MSGS-6-LAPP_ON_CAUSE_VTSP_DISCONNECTED 6-Information Telephony interface VTSP disconnected Call termination due to Telephony interface disconnect - LOG_STD_NO_ACTION LAT-3-BADDATA 3-Error Tty[t-line] Data pointer does not correspond to current packet An internal software error occurred. - "If this message recurs contact your technical support representative." LAT-3-BUFFULL 3-Error Tty[t-line] data buffer full with count [dec] An internal software error occurred. - "If this message recurs contact your technical support representative." LAT-3-NOSYNC 3-Error Tty[t-line] Output data ptrs out of sync with byte count An internal software error occurred. - "If this message recurs contact your technical support representative." LAT-3-NULLIDB 3-Error Null IDB pointer with destination [enet] An internal software error occurred. - "If this message recurs contact your technical support representative." LAT-3-QBSPACED 3-Error Queue block at [hec] not found for HI connection An internal software error occurred. - "If this message recurs contact your technical support representative." LAT-3-REUSE 3-Error Tty[t-line] Attempt to re-use slot array empty = [dec] fill = [dec] An internal software error occurred. - "If this message recurs contact your technical support representative." LATREVNUMWRAP-3-LCON 3-Error ERRMSG_NOFLAGS - - - LATREVNUMWRAP-3-LCON 3-Error ERRMSG_NOFLAGS - - - LAYER2_BRIDGE-3-ALLOC_FAILED 3-Error Allocation of [chars] memory failed for layer 2 bridging feature in QFP Allocation of memory by the QFP layer 2 bridging feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure qfp-bridging LOG_STD_ACTION LAYER2_BRIDGE-3-HA_BULK_SYNC_FAIL 3-Error rg [dec] There was a failure such that Layer 2 bridge domain bulk sync did not occur cpp-ucode LOG_STD_ACTION LAYER2_BRIDGE-3-HA_INVALID_STATE 3-Error state [dec] An invalid HA state was received from the HA infrastructure. cpp-ucode LOG_STD_ACTION LAYER2_BRIDGE-3-INIT_FAILED 3-Error Initialization of the layer 2 bridging feature in QFP failed Initialization of the layer 2 bridging feature in the QFP failed. This indicates a software failure. qfp-bridging LOG_STD_ACTION LAYER2_BRIDGE-3-PKT_REPLICA_INIT_FAILED 3-Error Failed to register with generic packet replication for layer 2 bridging feature in QFP Layer 2 bridging initialization of packet replication registration failed. qfp-bridging LOG_STD_ACTION LAYER2_SVI-3-ALLOC_FAILED 3-Error Allocation of [chars] memory failed for SVI feature in QFP Allocation of memory by the QFP SVI feature microcode failed. The name of the memory chunk is specified in the message. This indicates a software failure qfp-switch-infra LOG_STD_ACTION LAYER2_SVI-3-INIT_FAILED 3-Error Initialization of the SVI feature in QFP failed Initialization of the SVI feature in the QFP failed. This indicates a software failure. qfp-switch-infra LOG_STD_ACTION LAYER2_SVI-3-PKT_REPLICA_INIT_FAILED 3-Error Failed to register with generic packet replication for SVI feature in QFP SVI initialization of packet replication registration failed. qfp-switch-infra LOG_STD_ACTION LB-3-ACL_FCB_REG_ERROR 3-Error Failed to registered Link Bundle ACL feature control block For the given interface failed to register the ACL feature control block. gsr-link-bundling LOG_STD_ACTION LB-3-CHUNK_CREATE_FAIL 3-Error [chars]channel: failed to create chunk An internal data structure called a chunk and used for channel route processor - line card interprocess communications failed to be created. Such interprocss communication may be impeded. gsr-link-bundling LOG_STD_ACTION LB-3-ECHAN_ADDR_ALLOC_ERROR 3-Error Channel [dec] error in MAC address allocation configured MAC address [enet] actual MAC address [dec] For the given channel number addition of the first member caused a failure in changing the MAC address of the channel to that of this first member. gsr-link-bundling LOG_STD_ACTION LB-3-ECHAN_CMDREP_REG_FAILURE 3-Error Failed to register bundle interface [chars] for Command Replay service For the given link bundle interface failed to register it for the Command Replay service. gsr-link-bundling LOG_STD_ACTION LB-3-ECHAN_FCB_ERROR 3-Error Bundle creation feature callback failed for [chars] For the given link bundle interface failed to create its feature callback. gsr-link-bundling LOG_STD_ACTION LB-3-FEATURE_ACL_APPLY_ERROR 3-Error Failed to apply ACL [dec] to interface [chars]. Removing new ACL config reapplying old ACL [dec]. For the given member interface or subinterface failed to apply the given ACL. This new ACL configuration is removed from the bundle and the old ACL configuration if any is reapplied to the bundle. The new ACL that failed to be applied is removed in order to maintain consistent state for the whole bundle. gsr-link-bundling LOG_STD_ACTION LB-3-FEATURE_ACL_REG_ERROR 3-Error Failed to register ACL control block with Link Bundle subinterface module For the given interface failed to register the ACL feature control block. This happened during install ACL support for link bundling. ACL support installation for link bundling is aborted. gsr-link-bundling LOG_STD_ACTION LB-3-FEATURE_INSTALL_ERROR 3-Error One or more NULL feature control block members In installing link bundling feature support there were one or more NULL function pointers used in a feature control block. Installation of the feature support is aborted. gsr-link-bundling LOG_STD_ACTION LB-3-FEATURE_MODULE_INIT_ERROR 3-Error Failed to create Link Bundle Feature ListQ In initializing link bundling feature support an internal list queue failed to be created. gsr-link-bundling LOG_STD_ACTION LB-3-FEATURE_REG_ERROR 3-Error One or more NULL feature callbacks in the passed in Feature Control Block In registering a feature for services from link bundling feature support there were one or more NULL function pointers used as function callbacks. Aborted the feature registration as a result. gsr-link-bundling LOG_STD_ACTION LB-3-FUNCTION_VECTOR_EMPTY 3-Error Empty link bundling function vectors One or more function vectors used in generic etherchannel and poschannel code was null i.e. not initialized. This is a severe error resulting from a coding error. Crash will happen because this error prevents the proper functioning of the ether or pos channel features. gsr-link-bundling LOG_STD_ACTION LB-3-POSCHAN_CMDREP_REG_FAILURE 3-Error Failed to register bundle interface [chars] for Command Replay service For the given link bundle interface failed to register it for the Command Replay service. gsr-link-bundling LOG_STD_ACTION LB-3-POSCHAN_FCB_ERROR 3-Error Bundle creation feature callback failed for [chars] For the given link bundle interface failed to create its feature callback. gsr-link-bundling LOG_STD_ACTION LB-3-SUBINT_ERROR 3-Error [chars] [chars] There was a subinterfce error for the given interface. gsr-link-bundling LOG_STD_ACTION LB-3-SUBINT_INSTALL_SUPPORT_FAILURE 3-Error Failed to registered Link Bundle subinterface control block In initializing link bundling subinterface feature support could not register for notifications from the common link bundle infrastructure. gsr-link-bundling LOG_STD_ACTION LB-3-SUBINT_NOTIF_INIT_FAILURE 3-Error Failed to create Link Bundle Subinterface ClientQ In initializing link bundling subinterface feature support an internal subinterface client queue failed to be created. gsr-link-bundling "Copy the error message exactly as it appears and report it to your technical support representative." LB-3-SUBINT_NOTIF_REG_FAILURE 3-Error NULL notification callback In registering a client for service from the Link Bundling subinterface module the callback notification callback function was NULL. gsr-link-bundling LOG_STD_ACTION LB-5-CHAN_MEMBER_ADD_PASSIVE 5-Notice [chars] added as passive member to [chars]channel[dec] The given interface was added as a passive member in the given channel number. gsr-link-bundling LOG_STD_NO_ACTION LB-5-CHAN_MEMBER_IN 5-Notice [chars] added as member-[dec] to [chars]channel[dec] The given channel member interface was added to the given channel number. gsr-link-bundling LOG_STD_NO_ACTION LB-5-CHAN_MEMBER_MOVED_ACTIVE 5-Notice [chars] moved to active state as member-[dec] in [chars]channel[dec] The given etherchannel member interface became an active member in the given channel number. gsr-link-bundling LOG_STD_NO_ACTION LB-5-CHAN_MEMBER_MOVED_PASSIVE 5-Notice [chars] moved to passive state in [chars]channel[dec] The given channel member interface became a passive member in the given channel number. gsr-link-bundling LOG_STD_NO_ACTION LB-5-CHAN_MEMBER_OUT 5-Notice [chars] taken out of [chars]channel[dec] The given channel member interface was taken out of the given channel number. gsr-link-bundling LOG_STD_NO_ACTION LCB-3-LOCKFAILURE 3-Error Multiple LCB event processes scheduled This message occurs when LCB event process fails to lock the\n\ semaphore which is used to prevent multiple LCB processes from \n\ running. This implies that multiple LCB processes have been \n\ scheduled to run which should not happen - "Try executing the command again after a few minutes. If the problem\n\ persists contact Cisco Technical support" LCB-3-QUEUEFAILURE 3-Error LCB process unable to create event queue Unable to create LCB event queue. LCB process quit. The operating\n\ system was unable to allocate RAM space for the queue - "Try executing the command again after a few minutes. If the problem\n\ persists it indicates a lack of RAM space. Most likely the router \n\ image requires more system memory RAM than the router contains." LCD_DISPLAY-3-CHAR_ERROR 3-Error Invalid character This character is not supported by card LCD cmts-platform "Copy the error message exactly as it appears and report it to your " "technical support" LCD_DISPLAY-4-INPUT_ERROR 4-Warning Invalid input DS [dec] US [dec] channels Wrong number of D/S or U/S channels cmts-platform "Copy the error message exactly as it appears and report it to your" " technical support" LCD_DISPLAY-4-STATUS_ERROR 4-Warning Invalid status Invalid status bit cmts-platform "Copy the error message exactly as it appears and report it to your" " technical support" LCHA_INFRA-3-UNEXPECTED 3-Error [chars] An unexpected error has occured while performing a linecard HA action iosxe-iosd-lcha LOG_STD_LCHA_SUP_ACTION LCHA_INFRA-4-CUTOVER 4-Warning Cutover request received from slot [dec] A cutover interrupt received from a failing linecard cmts-platform-infra "Check core files and crashinfo files. Collect tech-support logs. Collect the system log using CLI 'show logging' and LCHA log on SUP using CLI 'show lcha logging level noise'." LCHA_INFRA-4-FORCE_RESET 4-Warning Reset slot [dec] for reason: [chars] The SUP forced a linecard to reload for the given reason. cmts-platform-infra LOG_STD_LCHA_SUP_ACTION LCHA_INFRA-5-SW_RESET 5-Notice Soft-reset slot [dec] [chars] The SUP software reset linecard's processes without HW reset it. cmts-platform-infra LOG_STD_NO_ACTION LCHA_INFRA-6-LCHA_INFO 6-Information [chars] lcha information for better monitor chassis lcha relates status - LOG_STD_NO_ACTION LCHA-3-CFR_LIST 3-Error Remove an element before destroy [chars]: cfrid=[dec] direction=[dec] state=[dec] ip_sadd=[inet] ip_daddr=[inet] dest_macaddr=[enet] src_macaddr=[enet] ip_prot=[dec] eport=[dec] Remove an element from interdb cfr_list before destroy the list. iosxe-iosd-lcha "Reset the system" LCHA-4-DYN_SRV 4-Warning CM [enet] [chars] transcation id [dec] is not end before lc switch Dynamic service not finished iosxe-iosd-lcha LOG_STD_NO_ACTION LCHA-4-RF_RESIL_IDX_OUT_OF_RANGE 4-Warning CM [enet] RF channel id [dec] is out of range [dec] RF channel index out of range iosxe-iosd-lcha LOG_STD_NO_ACTION LCINFO-3-CRASH 3-Error Line card in slot [dec]/[dec] crashed The line card in the slot indicated crashed and sent a CRASH_START message to the PRE. The PRE is now waiting for the rest of the crash information from the line card to be sent via the BPE stack trace context version etc.. This should ubr10k-sw "Report this defect with as much information about the line card " "in question including the output of show context summary show " "context slot N and show tech-support N as well as the usual show " "tech-support from the PRE." LCINFO-3-INVDEV 3-Error Invalid line card number in BPE callback LC=[dec]/[dec] The line card crash information subsystem on the PRE was called from the BPE subsystem with an invalid slot/subslot. The slot or subslot number is out of range. This indicates a software defect in the system. ubr10k-sw "Report this defect with as much information about the BPE " "subsystem as possible. There is no adverse effect to the PRE -- " "it ignores the bad callback and continues. If the problem " "persists reboot the router. It is unlikely but possible that " "the problem is due to bad BPE hardware somewhere in the system." LCINFO-3-INVSTATE 3-Error Line card crash server in bad state LC=[dec]/[dec]state=[dec] - - - LCINFO-3-NOBUF 3-Error Could not malloc line card crash structures on PRE size=[dec] The PRE could not malloc data structures for line card crash data structures at startup time. This is not in and of itself a Serious problem but the underlying memory shortage at startup time will probably prevent the router from running well if at all. ubr10k-sw "Add more memory and/or debug the memory shortage problem." LCINFO-3-NOBUFLC 3-Error Could not malloc line card crash info buffer on PRE bufnum=[dec]size=[dec] - - - LCINFO-3-NOLCHANGPROC 3-Error Failed creating line card hang cure process When creating the LC hang cure process for checking prolonged CLC down states the create_process call failed. This should not happen. It is probably due to a software defect or hardware failure. This failure should only happen during initialization. ubr10k-sw "Rebooting the system should fix this. If the condition persists " "on subsequent reloads of the system a bug should be filed and " "the system should be reloaded with a different image." LCINFO-3-NOPROCESS 3-Error Failed creating line card complete process When creating the crash complete process for the crash information subsystem the create_process call failed. This should not happen. It is probably due to a software defect or hardware failure. This failure should only happen during initialization. ubr10k-sw "Rebooting the system should fix this. If the condition persists " "on subsequent reloads of the system a bug should be filed and " "the system should be reloaded with a different image." LCINFO-3-TIMEOUT 3-Error Timeout waiting for crash info from slot [dec]/[dec] The crash information complete timer expired. When a line card crashes it sends information to the PRE for debugging and analysis. When the START OF CRASH message is recieved a timer is set for approx 10 seconds. The line card has 10 seconds to send all the crash information to the PRE. This is not a crash dump -- this is a small amount of information that usually includes context stack trace etc. It is less than 8K bytes of information. If an END OF CRASH information message is not received before the timer goes off the crash information record is closed contains partial information this message is ubr10k-sw "No action is required specifically because this message was " "displayed. Because the line card was crashing there might be " "other defects to report. If this message is seen without a line " "card crashing report this defect with the output of the usual " "commands includeing show tech-support on the PRE *AND* on the line " "card that didn't crash but was mentioned in this error " "message." LCINFO-4-LCHUNG 4-Warning Slot [[dec]/[dec]] down on last [dec] checks. HW RESET # [dec] ... A line card can get hung in some IOS operation and is not able to recover or when rommon can get stuck while initiating tftp bootload. This is the time when an external monitoring process on RP checks for health of each line card. And if the line card is found stuck for more than 150 seconds a hardware reset is issued for that subslot. ANd while issuing a hard reset this error message is displayed onto the console. ubr10k-sw "Report this LC defect with as much information about the LC" LCINFO-4-TRUNC 4-Warning Crash record [dec]=[chars] truncated expected=[dec]actual=[dec] A line card crashed an was sending crash information to the PRE. The PRE received a CRASH RECORD START message that indicated the data would be \expected\ bytes long. Before that many bytes were received the PRE received another CRASH RECORD START message indicating the start of another record. The current record is marked as truncated and the next record is received but the anomoly is noted in this error message. This is a problem but because what started this process was a line card crashing this might only be a symptom of another underlying problem. ubr10k-sw "Report this defect with as much information about the BPE subsystem " "and the line card crash information subsystem possible." LCINFO-4-UNXMSG 4-Warning Unexpected crash info msg type [chars] in state [chars] LC=[dec]/[dec] The line card crash information subsystem received an unexpected message for the state it is in. The state and message type are given in the error message. This does not have any adverse effect on the PRE since it ignores and/or recovers from this occurrence. Because the sender of these messages is a line card that is crashing it is not completely unbelievable that this might happen. The source of the crash on the line card is more interesting. If this occurs without a line card crashing it is due to a stray/errant BPE message that should be persued. This could also be due to a dropped BPE message. ubr10k-sw "Find the source of the crash on the line card if one was crashing " "when the message occurred. If no line card was crashing report " "this defect with as much information about the BPE subsystem and " "the line card crash information subsystem as possible. If this " "message persists rebooting the router might help remove this " "message." LCINFO-6-LCRESET 6-Information PRE switchover. Reset empty slot [[dec]/[dec]] When the standby PRE becomes active it resets all the slots which it thinks is empty. This prevents any linecards which was coming up during the PRE switchover from getting stuck ubr10k-sw "" LCLOG-3-INVDEV 3-Error Invalid slot/subslot number in logger API callback LC=[dec]/[dec] The line card crash info subsystem on the PRE was called from the BPE subsystem with an invalid slot/subslot. This indicates a software defect in the system. ubr10k-sw "Report this defect with as much information about the subsystem as " "possible. There is no adverse effect to the PRE -- it ignores the " "bad callback and continues. If the problem is recurring " "rebooting the router is recommended." LCLOG-3-INVSTATE 3-Error LC logger in bad state LC=[dec]/[dec]state=[chars]msg=[chars] - - - LCLOG-3-MSGGIANT 3-Error LC log msg larger than max allowed LC=[dec]/[dec]length=[dec] - - - LCLOG-3-MSGTOOBIG 3-Error LC log msg longer than expected LC=[dec]/[dec]len=[dec]exp=[dec] The PRE part of the line card logger server has received more text for a message than the start message indicated. This is probably due to a software defect. ubr10k-sw "Report this defect with as much information about the line card " "logger subsystem possible." LCLOG-3-OVERFLOW 3-Error LC log msg longer than msg buffer LC=[dec]/[dec]len=[dec]max=[dec] The PRE part of the line card logger server has received more text for a message than will fit in the message log buffer. This is probably due to a software defect. ubr10k-sw "Report this defect with as much information about the line card " "logger subsystem possible." LCLTAG_ALLOC-3-LCON 3-Error ERRMSG_NOFLAGS - - - LCLTAG_ALLOC-3-LCON 3-Error ERRMSG_NOFLAGS - - - LCMDC-3-ACCESS_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-DEBUG_INTF_CREATE_FAILED 3-Error Transparent Interface Creation Failed for slot [[dec]] Interface data structure creation/initialization failed - LOG_STD_ACTION LCMDC-3-EOP_NOLG_ALM 3-Error Egress Loss of Light: [chars] Egress side No Light - LOG_STD_ACTION LCMDC-3-EOP_NOLG_PALM 3-Error Egress Loss of Light Prealarm: [chars] CDL Drop FIFO Overflow Prealarm - LOG_STD_ACTION LCMDC-3-ETH_DCC_LPBK_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-FPGA_ACCESS_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-IDPROM_ACCESS_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-IDPROMCRCFAIL 3-Error IDPROM CRC check failed [[chars]] CRC check failed for IDPROM - LOG_STD_ACTION LCMDC-3-IDPROMMATCHFAIL 3-Error IDPROM mismatch read failed [[chars]] check with catched value fail - LOG_STD_ACTION LCMDC-3-IDPROMRDFAIL 3-Error IDPROM read failed [[chars]].\n \tThe card may not be inserted correctly. Please ensure that card is\n \tinserted completely and then please fasten the screws completely. The read error occurred when accessing the IDPROM - LOG_STD_ACTION LCMDC-3-INT_LPBK_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-INTF_CREATE_FAILED 3-Error Interface Create Failed [[chars]] Interface data structure creation/initialization failed - LOG_STD_ACTION LCMDC-3-INTF_DELETE_FAILED 3-Error Interface Delete Failed [[chars]] Interface data structure deletion failed - LOG_STD_ACTION LCMDC-3-INTRPENDING 3-Error Pending unexpected interrupt [addr [hex] = [hex]] One or more pending unexpected interrupts - LOG_STD_ACTION LCMDC-3-INVALIDCLKRATE 3-Error Non supported clock rate [dec] Khz The entered clock rate in Khz is not supported - LOG_STD_ACTION LCMDC-3-INVALIDSIGRATE 3-Error Non supported signal rate [dec] The entered enum signal rate is invalid - LOG_STD_ACTION LCMDC-3-LASER_DEGRADE 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-LASER_DEVIATION 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-LINE_LASER_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-LPBK_THRU_PSC_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-LRCMAGICREGRESET 3-Error Magic Register Reset Slot [dec] Magic Register Reset for Linecard in slot - LOG_STD_ACTION LCMDC-3-MDSUBCARD_IDPROM_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-MIB_CDL_HEC_ALM 3-Error CDL HEC Err count [chars] [chars] [chars] CDL HEC error count threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_CDL_RFOF_IND 3-Error CDL Drop FIFO OvrFL [chars] [chars] [chars] CDL Drop FIFO Overflow Prealarm - LOG_STD_ACTION LCMDC-3-MIB_ECDRLK_ALM 3-Error Egress CDR Locking error [chars] [chars] [chars] CDR is having trouble locking onto the signal. - LOG_STD_ACTION LCMDC-3-MIB_EOP_NOLG_ALM 3-Error Egress Loss of Light [chars] [chars] [chars] Egress side No Light - LOG_STD_ACTION LCMDC-3-MIB_EOP_NOLG_PALM 3-Error Egress Loss of Light Prealarm [chars] [chars] [chars] - - LOG_STD_ACTION LCMDC-3-MIB_EOP_TKSW_ALM 3-Error Egress Trunk Switch Mech. Failure [chars] [chars] [chars] Egress side switch failed to switch position during auto-failover - LOG_STD_ACTION LCMDC-3-MIB_ESERDESLK_ALM 3-Error Egress Serdes Locking error [chars] [chars] [chars] Serdes has trouble locking onto the signal - LOG_STD_ACTION LCMDC-3-MIB_ESERPHERR_ALM 3-Error Egress Serdes Phase Error [chars] [chars] [chars] Serdes has a phase error. - LOG_STD_ACTION LCMDC-3-MIB_FH_ECETX_ALM 3-Error Egress Fiber Channel/ESCON Line Err [chars] [chars] [chars] Fiber Channel/ESCON Line code error count exceeded threshold - LOG_STD_ACTION LCMDC-3-MIB_FH_ELOSY_ALM 3-Error Egress FC/ESCON Loss of Sync [chars] [chars] [chars] Fiber Channel/ESCON Syncronization error - LOG_STD_ACTION LCMDC-3-MIB_FH_ICETX_ALM 3-Error Ingress FC/ESCON Line Code err [chars] [chars] [chars] Ingress FC/ESCON Line code error count threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_FH_ILOSY_ALM 3-Error Ingress FC/ESCON Loss of Sync [chars] [chars] [chars] Ingress Fiber Channel/ESCON Loss of Syncronization - LOG_STD_ACTION LCMDC-3-MIB_GE_ECETX 3-Error Egress GE Line Code Err count [chars] [chars] [chars] GE Line Code error count exceeded threshold - LOG_STD_ACTION LCMDC-3-MIB_GE_ELOSY_ALM 3-Error Egress GE Loss of Sync [chars] [chars] [chars] GE Loss of Syncronization error - LOG_STD_ACTION LCMDC-3-MIB_GE_ILOSY_ALM 3-Error Ingress GE Loss of Sync [chars] [chars] [chars] Ingress GE Loss of the Syncronization - LOG_STD_ACTION LCMDC-3-MIB_GH_ICETX_ALM 3-Error Ingress GE Line Code Err [chars] [chars] [chars] Ingress Line Code error count threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_ICDRLK_ALM 3-Error Ingress CDR Locking error [chars] [chars] [chars] Ingress CDR failed to lock onto signal - LOG_STD_ACTION LCMDC-3-MIB_IOP_NOLG_ALM 3-Error Ingress Loss of Light [chars] [chars] [chars] Loss of Light - LOG_STD_ACTION LCMDC-3-MIB_ISERDESLK_ALM 3-Error Ingress Serdes Locking Error [chars] [chars] [chars] Ingress Serdes signal lock error - LOG_STD_ACTION LCMDC-3-MIB_ISERPHERR_ALM 3-Error Ingress Serdes Phase error [chars] [chars] [chars] Ingress Serdes out of Phase error - LOG_STD_ACTION LCMDC-3-MIB_LN_OFC_IND 3-Error Line OFC IND [chars] [chars] [chars] Ingress OFC Indication - LOG_STD_ACTION LCMDC-3-MIB_LN_TX_ALM 3-Error Line Laser Failure [chars] [chars] [chars] Laser failure - LOG_STD_ACTION LCMDC-3-MIB_SH_EBIP_ALM 3-Error Egress SONET BIP Err count [chars] [chars] [chars] SONET BIP Err count exceeded threshold - LOG_STD_ACTION LCMDC-3-MIB_SH_ELOF_ALM 3-Error Egress SONET Loss of Frame [chars] [chars] [chars] SONET Loss of Frame error - LOG_STD_ACTION LCMDC-3-MIB_SH_ESEF_ALM 3-Error Egress SONET SEF Prealarm [chars] [chars] [chars] Egress SONET Severely Errored Frame threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_SH_IBIP_ALM 3-Error Ingress SONET BIP error [chars] [chars] [chars] Ingress SONET BIP error count threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_SH_ILOF_ALM 3-Error Ingress SONET Loss of Frame [chars] [chars] [chars] Ingress SONET Loss of frame - LOG_STD_ACTION LCMDC-3-MIB_SH_ISEF_ALM 3-Error Ingress SONET SEF [chars] [chars] [chars] Ingress SONET Severely Errored Frame threshold exceeded - LOG_STD_ACTION LCMDC-3-MIB_TK_OFC_IND 3-Error Trunk OFC IND [chars] [chars] [chars] Egress OFC Indication - LOG_STD_ACTION LCMDC-3-MIB_TK_TX_ALM 3-Error Transmit Failure [chars] [chars] [chars] Transmit failure - LOG_STD_ACTION LCMDC-3-MIB_TK_TX_LDGR 3-Error Laser Degrade Trunk side [chars] [chars] [chars] Laser Degrade failure on the transmit side - LOG_STD_ACTION LCMDC-3-MIB_TK_TX_WD 3-Error Wavelength Deviation [chars] [chars] [chars] Wavelength deviation error - LOG_STD_ACTION LCMDC-3-MIB_TK_WDEGRADE_ALM 3-Error Trunk laser degrade: [chars] [chars] [chars] Trunk laser wavelength degrade - LOG_STD_ACTION LCMDC-3-MIB_TK_WDEVIATION_ALM 3-Error Trunk Laser wavelength deviation: [chars] [chars] [chars] Trunk laser wavelength deviation - LOG_STD_ACTION LCMDC-3-OPT_SWITCH_0_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-OPT_SWITCH_1_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-OPT_SWITCH_2_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-OPT_SWITCH_3_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-OSC_HW_FAIL 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-PORT_CREATE_FAILED 3-Error Port Creation Failed [[chars]] Port data structure creation/initialization failed - LOG_STD_ACTION LCMDC-3-PORTFAILASSERTED 3-Error Unexpected portfail asserted One or more unexpected portfails asserted - LOG_STD_ACTION LCMDC-3-RDWRFAIL 3-Error Read/write failed [[chars]] A read/write error occurred when accessing the hardware - LOG_STD_ACTION LCMDC-3-READYPRESENT 3-Error Card [slot [dec]] present but not ready Egress side switch failed to switch position during auto-failover - LOG_STD_ACTION LCMDC-3-STDBYOP_NOLG_ALM 3-Error Loss of Light on Standby: [chars] Ingress SONET BIP error count threshold exceeded - LOG_STD_ACTION LCMDC-3-TK_WDEGRADE_ALM 3-Error Trunk laser degrade: [chars] Trunk laser wavelength degrade - LOG_STD_ACTION LCMDC-3-TK_WDEVIATION_ALM 3-Error Trunk Laser wavelength deviation: [chars] Trunk laser wavelength deviation - LOG_STD_ACTION LCMDC-3-TRUNK_LASER_DEGRADE 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-TRUNK_LASER_DEVIATION 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-WAVELENGTH_DEVIATION 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-WAVELENGTH_MISMATCH 3-Error Alarm: [chars] [chars] [chars] [chars] [chars] Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCMDC-3-WLENCKFAIL 3-Error Unexpected trunk laser wavelength: [chars] Trunk laser wavelength is incorrect - LOG_STD_ACTION LCMDC-4-RATEMISMATCH 4-Warning Encap rate mismatched: [chars] The entered encap rate is not matched with xcvr type - LOG_STD_ACTION LCMDC-5-DEFWAVELEN 5-Notice Default wavelength selected: [chars] The inserted transponder can not support cached hwsb->itu_num so the default wavelength is used instead - LOG_STD_NO_ACTION LCMDC-6-TX_ALARM_SOAK 6-Information [chars]\n Submit An alarm - Prints out descriptive message - LOG_STD_ACTION LCON-3-ALLOC 3-Error Cannot alloc [chars] An attempt to allocate a LDP data structure failed\n\ because of a low memory condition. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-ALLOC 3-Error Cannot alloc [chars] An attempt to allocate a LDP data structure failed\n\ because of a low memory condition. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-ALLOC 3-Error Cannot alloc [chars] An attempt to allocate a LDP data structure failed\n\ because of a low memory condition. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-CONSISTENCY 3-Error [chars] An action attempted by the Label Control process encountered\n\ an unexpected condition. mpls-ldp "The request will be ignored. If it repeatedly occurs\n\ copy the message exactly as it appears and report it to your\n\ technical service representative." LCON-3-CONSISTENCY 3-Error [chars] An action attempted by the Label Control process encountered\n\ an unexpected condition. mpls-ldp "The request will be ignored. If it repeatedly occurs\n\ copy the message exactly as it appears and report it to your\n\ technical service representative." LCON-3-CONSISTENCY 3-Error [chars] An action attempted by the Label Control process encountered\n\ an unexpected condition. mpls-ldp "The request will be ignored. If it repeatedly occurs\n\ copy the message exactly as it appears and report it to your\n\ technical service representative." LCON-3-DEADADJ 3-Error [chars] [chars] An unexpected failure occurred while building a LDP protocol\n\ message for transmission to a LDP peer. It occurred when\n\ attempting to add a label binding or an address to the message. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-DEADADJ 3-Error [chars] [chars] An unexpected failure occurred while building a LDP protocol\n\ message for transmission to a LDP peer. It occurred when\n\ attempting to add a label binding or an address to the message. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-DEADADJ 3-Error [chars] [chars] An unexpected failure occurred while building a LDP protocol\n\ message for transmission to a LDP peer. It occurred when\n\ attempting to add a label binding or an address to the message. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-DEFCASE_BINDING_PIE 3-Error Unexpected blist_type [dec] for [chars] message from peer [chars] A LDP protocol message received from a LDP peer contained an\n\ unexpected binding list type. The message will be be ignored. mpls-ldp ACTION_IGNORE_PIE_TAGCON LCON-3-DEFCASE_BINDING_PIE 3-Error Unexpected blist_type [dec] for [chars] message from peer [chars] A LDP protocol message received from a LDP peer contained an\n\ unexpected binding list type. The message will be be ignored. mpls-ldp ACTION_IGNORE_PIE_TAGCON LCON-3-DEFCASE_BINDING_PIE 3-Error Unexpected blist_type [dec] for [chars] message from peer [chars] A LDP protocol message received from a LDP peer contained an\n\ unexpected binding list type. The message will be be ignored. mpls-ldp ACTION_IGNORE_PIE_TAGCON LCON-3-DUP_ADDR_RCVD 3-Error Duplicate Address [chars] advertised by peer [chars] is already bound to [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-DUP_ADDR_RCVD 3-Error Duplicate Address [chars] advertised by peer [chars] is already bound to [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-DUP_ADDR_RCVD 3-Error Duplicate Address [chars] advertised by peer [chars] is already bound to [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-EVENTQ 3-Error Can't alloc work item for [chars] An operation on the LDP Directed Adjacency data structure\n\ failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-EVENTQ 3-Error Can't alloc work item for [chars] An operation on the LDP Directed Adjacency data structure\n\ failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-EVENTQ 3-Error Can't alloc work item for [chars] An operation on the LDP Directed Adjacency data structure\n\ failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-INIT 3-Error process cannot initialize The label distribution and control process failed to initialize\n\ itself. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-INIT 3-Error process cannot initialize The label distribution and control process failed to initialize\n\ itself. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-INIT 3-Error process cannot initialize The label distribution and control process failed to initialize\n\ itself. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-LABEL_REGION 3-Error Platform specified information for label region [chars] is invalid. A platform service routine provides label region information about\n\ all label regions it supports. This error message is printed when\n\ the service routine does not specify its label region information\n\ correctly. mpls-ldp "Report this condition to your technical service representative." LCON-3-LABEL_REGION 3-Error Platform specified information for label region [chars] is invalid. A platform service routine provides label region information about\n\ all label regions it supports. This error message is printed when\n\ the service routine does not specify its label region information\n\ correctly. mpls-ldp "Report this condition to your technical service representative." LCON-3-LABEL_REGION 3-Error Platform specified information for label region [chars] is invalid. A platform service routine provides label region information about\n\ all label regions it supports. This error message is printed when\n\ the service routine does not specify its label region information\n\ correctly. mpls-ldp "Report this condition to your technical service representative." LCON-3-LATREVNUMWRAP 3-Error Label Local Address Table revision number wrapped The revision number used to manage advertisement of interface\n\ addresses to LDP peers overflowed. This will result in faulty\n\ advertisement of interface addresses to LDP peers and\n\ faulty label switching on those peers. mpls-ldp "To restore proper interface address advertisement reboot the\n\ platform. Report this condition to your technical service\n\ representative." LCON-3-LATREVNUMWRAP 3-Error Label Local Address Table revision number wrapped The revision number used to manage advertisement of interface\n\ addresses to LDP peers overflowed. This will result in faulty\n\ advertisement of interface addresses to LDP peers and\n\ faulty label switching on those peers. mpls-ldp "To restore proper interface address advertisement reboot the\n\ platform. Report this condition to your technical service\n\ representative." LCON-3-LATREVNUMWRAP 3-Error Label Local Address Table revision number wrapped The revision number used to manage advertisement of interface\n\ addresses to LDP peers overflowed. This will result in faulty\n\ advertisement of interface addresses to LDP peers and\n\ faulty label switching on those peers. mpls-ldp "To restore proper interface address advertisement reboot the\n\ platform. Report this condition to your technical service\n\ representative." LCON-3-LCLTAG_ALLOC 3-Error Cannot allocate local label - mpls-ldp "The number of labels available for allocation can be changed\n\ by the mpls label range ... configuration command.\n\ Consult with your technical service representative to determine\n\ whether you should use this command to increase the number of\n\ available labels." LCON-3-LCLTAG_ALLOC 3-Error Cannot allocate local label - mpls-ldp "The number of labels available for allocation can be changed\n\ by the mpls label range ... configuration command.\n\ Consult with your technical service representative to determine\n\ whether you should use this command to increase the number of\n\ available labels." LCON-3-LCLTAG_ALLOC 3-Error Cannot allocate local label - mpls-ldp "The number of labels available for allocation can be changed\n\ by the mpls label range ... configuration command.\n\ Consult with your technical service representative to determine\n\ whether you should use this command to increase the number of\n\ available labels." LCON-3-LDPID 3-Error peer [chars] LDP Id/Addr mapping problem [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-LDPID 3-Error peer [chars] LDP Id/Addr mapping problem [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-LDPID 3-Error peer [chars] LDP Id/Addr mapping problem [chars] EXPLANATION_ADDR_TBL_TAGCON mpls-ldp ACTION_TOGGLE_TAG_IP_TAGCON LCON-3-PEERSM 3-Error LDP peer [chars][chars]: [chars] An operation on the state machine for the label distribution and\n\ control process failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-PEERSM 3-Error LDP peer [chars][chars]: [chars] An operation on the state machine for the label distribution and\n\ control process failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-PEERSM 3-Error LDP peer [chars][chars]: [chars] An operation on the state machine for the label distribution and\n\ control process failed. mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-PROCESS 3-Error process not created An attempt to create the label distribution and control process\n\ failed. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-PROCESS 3-Error process not created An attempt to create the label distribution and control process\n\ failed. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-PROCESS 3-Error process not created An attempt to create the label distribution and control process\n\ failed. The probable cause is insufficient memory. mpls-ldp ACTION_STD_LOW_MEMORY_TAGCON LCON-3-RADIXTREE 3-Error [chars]LIB walk failed [chars] - mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-RADIXTREE 3-Error [chars]LIB walk failed [chars] - mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-RADIXTREE 3-Error [chars]LIB walk failed [chars] - mpls-ldp ACTION_COPY_REPORT_TAGCON LCON-3-REGISTRY 3-Error Unexpected [chars] for reg_invoke_[chars] - mpls-ldp - LCON-3-REGISTRY 3-Error Unexpected [chars] for reg_invoke_[chars] - mpls-ldp - LCON-3-REGISTRY 3-Error Unexpected [chars] for reg_invoke_[chars] - mpls-ldp - LCON-4-ADDR_PROC 4-Warning Can't create lcon addr proc - mpls-ldp "This is an informational message. As long as it needs the\n\ process the system will regularly attempt to create it. If\n\ this message occurs repeatedly copy it exactly as it appears\n\ and report it to your technical service representative." LCON-4-ADDR_PROC 4-Warning Can't create lcon addr proc - mpls-ldp "This is an informational message. As long as it needs the\n\ process the system will regularly attempt to create it. If\n\ this message occurs repeatedly copy it exactly as it appears\n\ and report it to your technical service representative." LCON-4-ADDR_PROC 4-Warning Can't create lcon addr proc - mpls-ldp "This is an informational message. As long as it needs the\n\ process the system will regularly attempt to create it. If\n\ this message occurs repeatedly copy it exactly as it appears\n\ and report it to your technical service representative." LCON-4-ADDRQ 4-Warning Can't alloc work item for [chars] - mpls-ldp "This is an informational message. The system remembers that\n\ it needs to do this work and will regularly attempt to queue\n\ the necessary work item. If this message occurs repeatedly\n\ copy it exactly as it appears and report it to your technical\n\ service representative." LCON-4-ADDRQ 4-Warning Can't alloc work item for [chars] - mpls-ldp "This is an informational message. The system remembers that\n\ it needs to do this work and will regularly attempt to queue\n\ the necessary work item. If this message occurs repeatedly\n\ copy it exactly as it appears and report it to your technical\n\ service representative." LCON-4-ADDRQ 4-Warning Can't alloc work item for [chars] - mpls-ldp "This is an informational message. The system remembers that\n\ it needs to do this work and will regularly attempt to queue\n\ the necessary work item. If this message occurs repeatedly\n\ copy it exactly as it appears and report it to your technical\n\ service representative." LCON-4-CFGD_LBL_REGION 4-Warning Adjusting configured label range to default range The saved configuration has been ignored and the default label range\n\ is being used. mpls-ldp "Please reconfigure the label range to a valid range using \n\ mpls label range ... configuration command." LCON-4-CFGD_LBL_REGION 4-Warning Adjusting configured label range to default range The saved configuration has been ignored and the default label range\n\ is being used. mpls-ldp "Please reconfigure the label range to a valid range using \n\ mpls label range ... configuration command." LCON-4-CFGD_LBL_REGION 4-Warning Adjusting configured label range to default range The saved configuration has been ignored and the default label range\n\ is being used. mpls-ldp "Please reconfigure the label range to a valid range using \n\ mpls label range ... configuration command." LCON-4-INIT_TAG_ALLOC 4-Warning Failure to initialize label allocation pool [dec] The system was unable to initialize the data structure used to support\n\ allocation of labels for label switching for the specified label pool. mpls-ldp - LCON-4-INIT_TAG_ALLOC 4-Warning Failure to initialize label allocation pool [dec] The system was unable to initialize the data structure used to support\n\ allocation of labels for label switching for the specified label pool. mpls-ldp - LCON-4-INIT_TAG_ALLOC 4-Warning Failure to initialize label allocation pool [dec] The system was unable to initialize the data structure used to support\n\ allocation of labels for label switching for the specified label pool. mpls-ldp - LCON-5-SEND 5-Notice cannot queue LDP [chars] message for [chars][chars] - mpls-ldp "This is an informational message. Failure to queue a message for\n\ a peer should occur only when the LDP session with the peer no\n\ longer exists. The software should recover from this\n\ situation by discarding the LDP session and trying to\n\ establish a new one. If this message occurs repeatedly copy\n\ it exactly as it appears and report it to your technical\n\ service representative." LCON-5-SEND 5-Notice cannot queue LDP [chars] message for [chars][chars] - mpls-ldp "This is an informational message. Failure to queue a message for\n\ a peer should occur only when the LDP session with the peer no\n\ longer exists. The software should recover from this\n\ situation by discarding the LDP session and trying to\n\ establish a new one. If this message occurs repeatedly copy\n\ it exactly as it appears and report it to your technical\n\ service representative." LCON-5-SEND 5-Notice cannot queue LDP [chars] message for [chars][chars] - mpls-ldp "This is an informational message. Failure to queue a message for\n\ a peer should occur only when the LDP session with the peer no\n\ longer exists. The software should recover from this\n\ situation by discarding the LDP session and trying to\n\ establish a new one. If this message occurs repeatedly copy\n\ it exactly as it appears and report it to your technical\n\ service representative." LCPR_INFRA-3-UNEXPECTED 3-Error [chars] An unexpected error has occured while performing linecard IOSD or CDMAN process restart. iosxe-iosd-lcpr "Check the IPC status of the platform. Collect the system log using CLI 'show logging' and LCHA log on SUP using CLI 'show lcha logging level noise'. Collect the lchaman iosd-clc and cdman btrace logs." LCPR_INFRA-5-PROGRESSION 5-Notice [chars] LCPR generic progression information. iosxe-iosd-lcpr LOG_STD_NO_ACTION LCRED-2-RECEIVE_SYNC_MESSAGE_FAILED 2-Critical Checkpointing sync message was received on Standby RP but it was corrupted or there was an error processing it. A sync message was sent from the Active RP and received on the Standby RP. The message was either empty corrupted or could not be processed by Standby client. If system is NOT in bulk sync mode then Standby RP will be reset. ha-lcred-infra "Informational. The linecard recovery " "infrastructure will take recovery actions." LCRED-2-RECEIVE_SYNC_MESSAGE_FAILED 2-Critical Checkpointing sync message was received on Standby RP but it was corrupted or there was an error processing it. A sync message was sent from the Active RP and received on the Standby RP. The message was either empty corrupted or could not be processed by Standby client. If system is NOT in bulk sync mode then Standby RP will be reset. ha-lcred-infra "Informational. The linecard recovery " "infrastructure will take recovery actions." LCRED-2-SEND_SYNC_MESSAGE_FAILED 2-Critical Checkpointing sync message to client on Standby RP was not received. A sync message was sent from the Active RP but it was never received or was received in corrupted form on the Standby RP. The platform code has been notified and platform-specific recovery actions will be taken. ha-lcred-infra "Informational. The linecard recovery " "infrastructure will take recovery actions." LCRED-2-SEND_SYNC_MESSAGE_FAILED 2-Critical Checkpointing sync message to client on Standby RP was not received. A sync message was sent from the Active RP but it was never received or was received in corrupted form on the Standby RP. The platform code has been notified and platform-specific recovery actions will be taken. ha-lcred-infra "Informational. The linecard recovery " "infrastructure will take recovery actions." LCRED-2-SUBSYSTEM_INIT_FAILED 2-Critical Subsystem failed during init phase with error [chars]. During subsystem initialization for LCRED Line Card Redundancy subsystem an unrecoverable error occurred. The system will come up and run fine but linecard redundancy will not be available for configuration and will not come up if it was already configured in start-config. ha-lcred-infra "You can continue to use the system without " "linecard redundancy. At your earliest convenience reloading the " "system might allow linecard redundancy subsystem to come up. In " "any case report the error message to TAC and include the " "following: 'show run' 'show redundancy linecard history' " "'show redundancy linecard all' and 'show version'." LCRED-2-SUBSYSTEM_INIT_FAILED 2-Critical Subsystem failed during init phase with error [chars]. During subsystem initialization for LCRED Line Card Redundancy subsystem an unrecoverable error occurred. The system will come up and run fine but linecard redundancy will not be available for configuration and will not come up if it was already configured in start-config. ha-lcred-infra "You can continue to use the system without " "linecard redundancy. At your earliest convenience reloading the " "system might allow linecard redundancy subsystem to come up. In " "any case report the error message to TAC and include the " "following: 'show run' 'show redundancy linecard history' " "'show redundancy linecard all' and 'show version'." LCRED-2-SYNC_FAILURE_NO_BUFFER 2-Critical Could not get sync buffer to checkpoint data. An attempt to get a sync buffer failed when trying to sync data from Active RP to Standby. This is likely a system memory issue. The platform code has been notified to take possible corrective action. ha-lcred-infra "Informational. The system will correct " "if possible." LCRED-2-SYNC_FAILURE_NO_BUFFER 2-Critical Could not get sync buffer to checkpoint data. An attempt to get a sync buffer failed when trying to sync data from Active RP to Standby. This is likely a system memory issue. The platform code has been notified to take possible corrective action. ha-lcred-infra "Informational. The system will correct " "if possible." LCRED-3-CANT_SET_ROLE 3-Error Couldn't set or clear slot or port roles for Line card [chars] idx=[dec]. Failed when attempting to set or clear the slot or port Active/Standby roles for a Line Card . ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'." LCRED-3-CANT_SET_ROLE 3-Error Couldn't set or clear slot or port roles for Line card [chars] idx=[dec]. Failed when attempting to set or clear the slot or port Active/Standby roles for a Line Card . ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'." LCRED-3-COULDNT_ADD_REDUNDANT_IF 3-Error Error occurred while configuring redundant interface [dec]/[dec]: [chars] While configuring a redundant i/f the specified error occurred. This means the redundant configuration command was NOT successfully completed. ha-lcred-infra "First verify the command was correct and " "verify the current redundancy config with 'show redundancy " "linecard all' and 'show redundancy linecard group all'. If you " "feel the command was correct and failed anyway file a TAC " "case with the following: 'show run' 'show redundancy linecard " "history' 'show redundancy linecard all' 'show proc mem' and " "'show version'." LCRED-3-COULDNT_ADD_REDUNDANT_IF 3-Error Error occurred while configuring redundant interface [dec]/[dec]: [chars] While configuring a redundant i/f the specified error occurred. This means the redundant configuration command was NOT successfully completed. ha-lcred-infra "First verify the command was correct and " "verify the current redundancy config with 'show redundancy " "linecard all' and 'show redundancy linecard group all'. If you " "feel the command was correct and failed anyway file a TAC " "case with the following: 'show run' 'show redundancy linecard " "history' 'show redundancy linecard all' 'show proc mem' and " "'show version'." LCRED-3-EREVENT1 3-Error [chars] 0x[hec] This message is used for reporting invalid values for parameters or database members. ha-lcred-infra "Check the redundancy configuration for the " "slot with 'show redundancy linecard all' and 'show " "redundancy linecard group all'. Fix the configuration " "if required and re-execute the command making sure " "any command parameters are correct. If it's still in " "error then file a case with TAC. In addition to the " "usual system information provide them with the output " "from above commands and 'show redundancy linecard " "history'." LCRED-3-EREVENT1 3-Error [chars] 0x[hec] This message is used for reporting invalid values for parameters or database members. ha-lcred-infra "Check the redundancy configuration for the " "slot with 'show redundancy linecard all' and 'show " "redundancy linecard group all'. Fix the configuration " "if required and re-execute the command making sure " "any command parameters are correct. If it's still in " "error then file a case with TAC. In addition to the " "usual system information provide them with the output " "from above commands and 'show redundancy linecard " "history'." LCRED-3-HWIDB_SUBBLOCK_CREATE_FAIL 3-Error Creation of hwidb subblock for [chars] i/f [chars] failed. Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be created then creation of the redundant i/f will fail. ha-lcred-infra "Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' and 'show redundancy " "linecard all' in addition to usual system configuration " "information." LCRED-3-HWIDB_SUBBLOCK_CREATE_FAIL 3-Error Creation of hwidb subblock for [chars] i/f [chars] failed. Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be created then creation of the redundant i/f will fail. ha-lcred-infra "Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' and 'show redundancy " "linecard all' in addition to usual system configuration " "information." LCRED-3-INVALID_DEBUG 3-Error Invalid debug type parameter [dec] specified. The function responsible for turning debugging on/off was called with an invalid debug type code. ha-lcred-infra "Verify the debug command is available " "by 'debug redundancy lc ?' and try it again." LCRED-3-INVALID_DEBUG 3-Error Invalid debug type parameter [dec] specified. The function responsible for turning debugging on/off was called with an invalid debug type code. ha-lcred-infra "Verify the debug command is available " "by 'debug redundancy lc ?' and try it again." LCRED-3-IPC 3-Error \n[chars] General IPC error. ha-lcred-infra "Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'." LCRED-3-IPC 3-Error \n[chars] General IPC error. ha-lcred-infra "Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'." LCRED-3-IPCPORT 3-Error Can't Create IPC port [chars] error [chars] IPC err[chars]. Can't create IPC to receive traffic from peer. ha-lcred-infra "Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'." LCRED-3-IPCPORT 3-Error Can't Create IPC port [chars] error [chars] IPC err[chars]. Can't create IPC to receive traffic from peer. ha-lcred-infra "Check redundancy configuration with " "'show redundancy linecard all'. If the configuration is not " "what you expected try the commands again. If the configuration " "is correct and you get this message try switching over the " "linecard if the standby LC is configured and ready. Otherwise " "try resetting the linecard in the slot specified. If you still " "get the error submit a TAC case with the system information " "'show redundancy linecard all' and 'show proc mem'." LCRED-3-LC_CANT_SET_TXRX 3-Error Unable to set Active/Standby Tx/Rx selection for Line Card [chars] idx=[dec]. Platform driver rejected a request to set the Tx/Rx selectors for a redundant linecard. ha-lcred-infra "This indicates the platform was unable to " "initialize linecard Active/STandby states. User should check " "redundancy config and try to remedy via CLI if not correct. " "Check config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'." LCRED-3-LC_CANT_SET_TXRX 3-Error Unable to set Active/Standby Tx/Rx selection for Line Card [chars] idx=[dec]. Platform driver rejected a request to set the Tx/Rx selectors for a redundant linecard. ha-lcred-infra "This indicates the platform was unable to " "initialize linecard Active/STandby states. User should check " "redundancy config and try to remedy via CLI if not correct. " "Check config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'." LCRED-3-LC_CARD_MISMATCH 3-Error Mismatch is seen between Inserted card type0x%X [dec] and Inserted card type is rejected by lcred component due to mismatch between inserted card type and reserved card type ha-lcred-infra "This indicates the reserved card type is " "different than inserted card type. Check the reserve-cardtype setting " "in show run. Insert the card type same of reserve card type " "If the cards are of same type but still it shows mismatch then open " "a TAC case attaching output of 'show run' " "'redundancy linecard group all' 'redundancy lincard group .'" LCRED-3-LC_CARD_MISMATCH 3-Error Mismatch is seen between Inserted card type0x%X [dec] and Inserted card type is rejected by lcred component due to mismatch between inserted card type and reserved card type ha-lcred-infra "This indicates the reserved card type is " "different than inserted card type. Check the reserve-cardtype setting " "in show run. Insert the card type same of reserve card type " "If the cards are of same type but still it shows mismatch then open " "a TAC case attaching output of 'show run' " "'redundancy linecard group all' 'redundancy lincard group .'" LCRED-3-LC_PROG_RETURNED_ERROR 3-Error Progression attempt returned error for Line Card [chars] idx=[dec]. Attempt to complete progression failed. ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy " "config and try to remedy via CLI if not correct. Check " "config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'." LCRED-3-LC_PROG_RETURNED_ERROR 3-Error Progression attempt returned error for Line Card [chars] idx=[dec]. Attempt to complete progression failed. ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy " "config and try to remedy via CLI if not correct. Check " "config by 'show redundancy linecard all' and 'show " "redundancy linecard group all'. If redundancy config cannot " "be corrected then open a TAC case attaching the info above " "and also 'show redundancy linecard history' 'show version' " "and 'show run'." LCRED-3-LC_PROG_TO_INIT_ERROR 3-Error Unable to reset progression to INIT for Line Card [chars] idx=[dec]. Attempt to reinitialize progression failed. ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'." LCRED-3-LC_PROG_TO_INIT_ERROR 3-Error Unable to reset progression to INIT for Line Card [chars] idx=[dec]. Attempt to reinitialize progression failed. ha-lcred-infra "This indicates an error during redundant " "linecard state progression. User should check redundancy config " "and try to remedy via CLI if not correct. Check config by " "'show redundancy linecard all' and 'show redundancy linecard " "group all'. If redundancy config cannot be corrected then " "open a TAC case attaching the info above and also 'show " "redundancy linecard history' 'show version' and 'show run'." LCRED-3-LC_ROLE_NEG_DONE_WITH_ILLEGAL_ROLE 3-Error Illegal Line Card redundancy role assignments found following role negotiation. When LC role negotiation is done illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal. ha-lcred-infra "Informational only. The LC Redundancy system " "will take recovery action." LCRED-3-LC_ROLE_NEG_DONE_WITH_ILLEGAL_ROLE 3-Error Illegal Line Card redundancy role assignments found following role negotiation. When LC role negotiation is done illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal. ha-lcred-infra "Informational only. The LC Redundancy system " "will take recovery action." LCRED-3-LC_STATE_PROG_ERROR 3-Error Illegal event in redundant Line Card [chars] idx=[dec] state progression. Illegal event in redundant Line Card state progression. ha-lcred-infra "This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'." LCRED-3-LC_STATE_PROG_ERROR 3-Error Illegal event in redundant Line Card [chars] idx=[dec] state progression. Illegal event in redundant Line Card state progression. ha-lcred-infra "This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'." LCRED-3-LC_STATE_PROG_FAILED 3-Error Redundant Line Card [chars] idx=[dec] state progression failure. Line Redundant Line Card state progression failure. ha-lcred-infra "This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'." LCRED-3-LC_STATE_PROG_FAILED 3-Error Redundant Line Card [chars] idx=[dec] state progression failure. Line Redundant Line Card state progression failure. ha-lcred-infra "This is informational. The LCRED system " "will reset the linecard to recover. No action is required " "unless the error keeps re-occurring. If it keeps happening " "then open a TAC case. Include 'show redundancy linecard all' " "'show redundancy linecard group all' and 'show redundancy " "linecard history'." LCRED-3-LC_STATE_PROG_HARD_FAILURE 3-Error Redundant Line Card [chars] idx=[dec] state progression failed more than [dec] Redundant Line Card state progression failure rate exceeds threshold. ha-lcred-infra "Open a TAC case attaching the following: " "'show redundancy linecard all' 'show redundancy linecard group " "all' 'show redundancy linecard history' 'show version' and " "'show run'." LCRED-3-LC_STATE_PROG_HARD_FAILURE 3-Error Redundant Line Card [chars] idx=[dec] state progression failed more than [dec] Redundant Line Card state progression failure rate exceeds threshold. ha-lcred-infra "Open a TAC case attaching the following: " "'show redundancy linecard all' 'show redundancy linecard group " "all' 'show redundancy linecard history' 'show version' and " "'show run'." LCRED-3-LC_UP_WITH_ILLEGAL_ROLE 3-Error Illegal Line Card redundancy role assignments during linecard up. When LC comes up illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal. ha-lcred-infra "Informational only. The system will reset " "both linecards in the redundant pair to recover." LCRED-3-LC_UP_WITH_ILLEGAL_ROLE 3-Error Illegal Line Card redundancy role assignments during linecard up. When LC comes up illegal Line Card redundancy role was assigned to it and/or its peer. There are four kinds of roles can be assigned to a LC: Active Standby Wait or None. The only legal combination of roles for a slot and its peer are: Active-NONE Active-Standby WAIT-NONE. The rest are all illegal. ha-lcred-infra "Informational only. The system will reset " "both linecards in the redundant pair to recover." LCRED-3-MEMBERTWICE 3-Error LC: Request to add slot member [dec] twice to group [dec]. An attempt was made to add a member from the specified slot to a redundant interface group which already contains a member from that slot. ha-lcred-infra "This is a user error. Please double-check " "the configuration with 'show redundancy linecard group " "all' and try the command again." LCRED-3-MEMBERTWICE 3-Error LC: Request to add slot member [dec] twice to group [dec]. An attempt was made to add a member from the specified slot to a redundant interface group which already contains a member from that slot. ha-lcred-infra "This is a user error. Please double-check " "the configuration with 'show redundancy linecard group " "all' and try the command again." LCRED-3-NO_HWIDB_RED_SUBBLOCK 3-Error No redundancy subblock is found for i/f [chars]. Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be found then an error is reported. ha-lcred-infra "Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' 'show redundancy " "linecard all' and 'show redundancy linecard sub-block all' " "in addition to usual system configuration information." LCRED-3-NO_HWIDB_RED_SUBBLOCK 3-Error No redundancy subblock is found for i/f [chars]. Each redundant i/f whether active standby or virtual has a hwidb subblock that stores redundancy information about that i/f. If this subblock cannot be found then an error is reported. ha-lcred-infra "Try the CLI that triggered it again. If the " "error occurs again open a case with TAC. Report the output of " "'show redundancy linecard group all' 'show redundancy " "linecard all' and 'show redundancy linecard sub-block all' " "in addition to usual system configuration information." LCRED-3-NO_MORE_PREALLOCATED_SUBBLOCK_MEMORY 3-Error Could not allocate redundancy subblock. Pre-allocated memory for subblock creation of [dec] is exhausted. The platform pre-allocates a pool of memory for creating redundancy subblocks via registry plfm_get_max_redundancy_sb. This pool has been ha-lcred-infra "Open a case with TAC. Report the contents " "of this message including the preallocation size value. " "Provide TAC with the following information: 'show run' " "'show ver' 'show hardware' and 'show proc mem'. TAC " "will need to get the platform in question to increase " "the pre-allocated pool of memory." LCRED-3-NO_MORE_PREALLOCATED_SUBBLOCK_MEMORY 3-Error Could not allocate redundancy subblock. Pre-allocated memory for subblock creation of [dec] is exhausted. The platform pre-allocates a pool of memory for creating redundancy subblocks via registry plfm_get_max_redundancy_sb. This pool has been ha-lcred-infra "Open a case with TAC. Report the contents " "of this message including the preallocation size value. " "Provide TAC with the following information: 'show run' " "'show ver' 'show hardware' and 'show proc mem'. TAC " "will need to get the platform in question to increase " "the pre-allocated pool of memory." LCRED-3-NO_SLOT_TO_DELETE 3-Error LC: Request to delete non-member slot [dec] from redundancy group [dec]. An attempt was made to delete a slot from a redundant line card group which does not contain the specified slot as a member. ha-lcred-infra "Check the configuration with 'show " "redundancy linecard group all' and try command again." LCRED-3-NO_SLOT_TO_DELETE 3-Error LC: Request to delete non-member slot [dec] from redundancy group [dec]. An attempt was made to delete a slot from a redundant line card group which does not contain the specified slot as a member. ha-lcred-infra "Check the configuration with 'show " "redundancy linecard group all' and try command again." LCRED-3-NOINITMEM 3-Error Subsystem Init [chars] Failed due to unavailability of memory of Initialization of LCRED subsystem failed due to insufficient memory. ha-lcred-infra "This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions." LCRED-3-NOINITMEM 3-Error Subsystem Init [chars] Failed due to unavailability of memory of Initialization of LCRED subsystem failed due to insufficient memory. ha-lcred-infra "This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions." LCRED-3-NOIPCMEM 3-Error Cannot Allocate IPC memory to get message. Can't allocate memory to send redundancy control message. ha-lcred-infra "This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions." LCRED-3-NOIPCMEM 3-Error Cannot Allocate IPC memory to get message. Can't allocate memory to send redundancy control message. ha-lcred-infra "This is indicative of system memory " "shortage. The problem is likely unrelated to linecard " "redundancy. You should initiate recovery procedures as " "you would for any system that does not have sufficient " "memory to perform actions." LCRED-3-REMOVE_SLOT_OR_IF_FAILURE 3-Error Removal of redundant interface caused an unexpected condition for i/f [chars]. While removing a redundant i/f possibly during redundant LC removal a SW bug was encountered. LC redundancy ha-lcred-infra "Verify LC Redundancy config with 'show " "redundancy linecard all' and 'show redundancy linecard group " "all'. Try to fix config with CLI. Open TAC case with above " "output as well as 'show run' 'show ver' and 'show redundancy " "history'." LCRED-3-REMOVE_SLOT_OR_IF_FAILURE 3-Error Removal of redundant interface caused an unexpected condition for i/f [chars]. While removing a redundant i/f possibly during redundant LC removal a SW bug was encountered. LC redundancy ha-lcred-infra "Verify LC Redundancy config with 'show " "redundancy linecard all' and 'show redundancy linecard group " "all'. Try to fix config with CLI. Open TAC case with above " "output as well as 'show run' 'show ver' and 'show redundancy " "history'." LCRED-3-SYNC_FAILURE_ISSU_NOT_OK 3-Error Could not send checkpoint message during [chars] sync because issu infrastructure deemed ISSU state is incorrect. The ISSU infrastructure deemed the ISSU state of Linecard Redundancy's ISSU client peer is incorrect. ha-lcred-infra "If this message occurs once ISSU client " "negotiation is complete and system is up and running " "you need to reset the Standby RP. If it occurs during " "system bringup nothing needs to be done. The HA " "infrastructure should recover without intervention." LCRED-3-SYNC_FAILURE_ISSU_NOT_OK 3-Error Could not send checkpoint message during [chars] sync because issu infrastructure deemed ISSU state is incorrect. The ISSU infrastructure deemed the ISSU state of Linecard Redundancy's ISSU client peer is incorrect. ha-lcred-infra "If this message occurs once ISSU client " "negotiation is complete and system is up and running " "you need to reset the Standby RP. If it occurs during " "system bringup nothing needs to be done. The HA " "infrastructure should recover without intervention." LCRED-3-UNMAPPED_IFINDEX 3-Error NULL/Invalid [chars] ifindex 0x[hec] downloaded for interface group number [dec]. The interface identifier specified for a member or virtual interface of a redundant interface group does not correspond to a known interface. ha-lcred-infra "Open a TAC case. Attach the output of " "'show redundancy linecard all' 'show redundancy " "linecard group all' and 'show redundancy linecard " "history'." LCRED-3-UNMAPPED_IFINDEX 3-Error NULL/Invalid [chars] ifindex 0x[hec] downloaded for interface group number [dec]. The interface identifier specified for a member or virtual interface of a redundant interface group does not correspond to a known interface. ha-lcred-infra "Open a TAC case. Attach the output of " "'show redundancy linecard all' 'show redundancy " "linecard group all' and 'show redundancy linecard " "history'." LCRED-3-UPDATENOTSENT 3-Error The update message was not sent to the linecards - - - LCRED-3-UPDATENOTSENT 3-Error The update message was not sent to the linecards - - - LCRED-3-VIF_HWIDB_CREATE_FAIL 3-Error Virtual hwidb creation failed from physical i/f [chars]: [chars]. Creation of virtual hwidb failed with specified error. ha-lcred-infra "Without the virtual hwidb VIF the i/f " LCRED-3-VIF_HWIDB_CREATE_FAIL 3-Error Virtual hwidb creation failed from physical i/f [chars]: [chars]. Creation of virtual hwidb failed with specified error. ha-lcred-infra "Without the virtual hwidb VIF the i/f " LCRED-3-VIFTWICE 3-Error LC: Request to add a second virtual interface to group [dec]. An attempt was made to add a virtual interface to a redundant interface group which already has a configured virtual interface. ha-lcred-infra "If this error was in response to a user " "command then check the command and try again if it " "appears correct. If the error seems to be from some " "undefined action then file a TAC case and attach the " "output from 'show redundancy linecard group all' and " "'show redundancy linecard history'." LCRED-3-VIFTWICE 3-Error LC: Request to add a second virtual interface to group [dec]. An attempt was made to add a virtual interface to a redundant interface group which already has a configured virtual interface. ha-lcred-infra "If this error was in response to a user " "command then check the command and try again if it " "appears correct. If the error seems to be from some " "undefined action then file a TAC case and attach the " "output from 'show redundancy linecard group all' and " "'show redundancy linecard history'." LCRED-4-LC_PLFM_SUPPRESS_SWITCHOVER 4-Warning Platform has requested to temporarily suppress switchover for Line card redundancy group Group Index=[dec]. Attempt to switchover is suppress. This is just the informative message and not the error ha-lcred-infra "This indicates an informative error message " "during switchover.If secondary is never becoming Active for the " "failed or removed primary after Chassis reload then open a TAC " "case." LCRED-4-LC_PLFM_SUPPRESS_SWITCHOVER 4-Warning Platform has requested to temporarily suppress switchover for Line card redundancy group Group Index=[dec]. Attempt to switchover is suppress. This is just the informative message and not the error ha-lcred-infra "This indicates an informative error message " "during switchover.If secondary is never becoming Active for the " "failed or removed primary after Chassis reload then open a TAC " "case." LCRED-4-LC_PLFM_SUPPRESS_SWITCHOVER 4-Warning - - - - LCRED-4-PARTIAL_CONFIG_LOSS 4-Warning Partial redundancy config loss while configuring redundant interface [dec]/[dec] During system reload could not get hwidb for the Secondary i/f so the Secondary redundancy configuration will be lost. The Primary i/f will be Active if it was parsed correctly. ha-lcred-infra "Verify that Primary i/f is configured. " "Reconfigure Secondary i/f for redundancy." LCRED-4-PARTIAL_CONFIG_LOSS 4-Warning Partial redundancy config loss while configuring redundant interface [dec]/[dec] During system reload could not get hwidb for the Secondary i/f so the Secondary redundancy configuration will be lost. The Primary i/f will be Active if it was parsed correctly. ha-lcred-infra "Verify that Primary i/f is configured. " "Reconfigure Secondary i/f for redundancy." LDP-3-AUTOCFG 3-Error Interface [chars] is in an unexpected autoconfig state 0x[hec] [chars] request. An interface is in an unexpected LDP auto config state. This could\n\ impact the LDP session running on this interface mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-AUTOCFG 3-Error Interface [chars] is in an unexpected autoconfig state 0x[hec] [chars] request. An interface is in an unexpected LDP auto config state. This could\n\ impact the LDP session running on this interface mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-AUTOCFG 3-Error Interface [chars] is in an unexpected autoconfig state 0x[hec] [chars] request. An interface is in an unexpected LDP auto config state. This could\n\ impact the LDP session running on this interface mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-CONSISTENCY 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-CONSISTENCY 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-CONSISTENCY 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-GENERAL 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-GENERAL 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-GENERAL 3-Error [chars] - mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISSU_XFORM 3-Error ISSU [chars] transformation failed for msg type [dec][chars]. - - - LDP-3-ISSU_XFORM 3-Error ISSU [chars] transformation failed for msg type [dec][chars]. - - - LDP-3-ISSU_XFORM 3-Error ISSU [chars] transformation failed for msg type [dec][chars]. - - - LDP-3-ISYNC 3-Error [chars] An unexpected error happened in LDP-IGP Synchronization operation. mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISYNC 3-Error [chars] An unexpected error happened in LDP-IGP Synchronization operation. mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISYNC 3-Error [chars] An unexpected error happened in LDP-IGP Synchronization operation. mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISYNC_CHKPT 3-Error [chars]:: [chars] request failed [chars] An unexpected condition happened while uncheckpointing mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISYNC_CHKPT 3-Error [chars]:: [chars] request failed [chars] An unexpected condition happened while uncheckpointing mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-ISYNC_CHKPT 3-Error [chars]:: [chars] request failed [chars] An unexpected condition happened while uncheckpointing mpls-ldp ACTION_COPY_REPORT_TDP LDP-3-KA_NOMEMORY 3-Error Can't alloc KA message An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP Keep Alive protocol message has failed. mpls-ldp "The system will continue by omitting transmission of the LDP\n\ Keep Alive Message. This may result in termination of one or more\n\ LDP sessions as the peers time out the sessions. If this\n\ message persists reduce other system activity if possible\n\ and call your technical service representative for\n\ assistance." LDP-3-KA_NOMEMORY 3-Error Can't alloc KA message An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP Keep Alive protocol message has failed. mpls-ldp "The system will continue by omitting transmission of the LDP\n\ Keep Alive Message. This may result in termination of one or more\n\ LDP sessions as the peers time out the sessions. If this\n\ message persists reduce other system activity if possible\n\ and call your technical service representative for\n\ assistance." LDP-3-KA_NOMEMORY 3-Error Can't alloc KA message An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP Keep Alive protocol message has failed. mpls-ldp "The system will continue by omitting transmission of the LDP\n\ Keep Alive Message. This may result in termination of one or more\n\ LDP sessions as the peers time out the sessions. If this\n\ message persists reduce other system activity if possible\n\ and call your technical service representative for\n\ assistance." LDP-3-PTCLREAD 3-Error peer [chars] read failure An error occurred while attempting to read a LDP PDU received\n\ from a peer. mpls-ldp ACTION_NEW_SESSION_TDP LDP-3-PTCLREAD 3-Error peer [chars] read failure An error occurred while attempting to read a LDP PDU received\n\ from a peer. mpls-ldp ACTION_NEW_SESSION_TDP LDP-3-PTCLREAD 3-Error peer [chars] read failure An error occurred while attempting to read a LDP PDU received\n\ from a peer. mpls-ldp ACTION_NEW_SESSION_TDP LDP-3-RECONNECT 3-Error [chars] An error occurred while parsing the incoming LDP Initialization message.\n\ The FT Reconnect Timer value received was greater than\n\ the locally-configured Forwarding State Holding Timer value. mpls-ldp "Reconfigure the Forwarding State Holding Timer value." LDP-3-RECONNECT 3-Error [chars] An error occurred while parsing the incoming LDP Initialization message.\n\ The FT Reconnect Timer value received was greater than\n\ the locally-configured Forwarding State Holding Timer value. mpls-ldp "Reconfigure the Forwarding State Holding Timer value." LDP-3-RECONNECT 3-Error [chars] An error occurred while parsing the incoming LDP Initialization message.\n\ The FT Reconnect Timer value received was greater than\n\ the locally-configured Forwarding State Holding Timer value. mpls-ldp "Reconfigure the Forwarding State Holding Timer value." LDP-3-SM 3-Error unexpected event: peer [chars][chars] state=[chars] event=[chars][chars] An operation on the state machine for a LDP peer failed. mpls-ldp ACTION_IGNORE_REST_OF_PIE_TDP LDP-3-SM 3-Error unexpected event: peer [chars][chars] state=[chars] event=[chars][chars] An operation on the state machine for a LDP peer failed. mpls-ldp ACTION_IGNORE_REST_OF_PIE_TDP LDP-3-SM 3-Error unexpected event: peer [chars][chars] state=[chars] event=[chars][chars] An operation on the state machine for a LDP peer failed. mpls-ldp ACTION_IGNORE_REST_OF_PIE_TDP LDP-3-TAGATM_BAD_RANGE 3-Error Interface [chars] Bad VPI/VCI range. Can't start a LDP session The session parameters proposed by an LDP peer differ from those\n\ preferred by the platform. The differences are not sufficient to\n\ prevent the LDP session from being established but may have an\n\ impact on label distribution operation mpls-ldp "If the parameters identified relate to the optional path vector-based\n\ loop detection mechanism note that the IETF LDP specification\n\ recommends that when Loop Detection is enabled in a portion of a\n\ network it is recommended that all LSRs in that portion of the\n\ network be configured with Loop Detection enabled and with the\n\ same path vector limit. If the parameters identified relate\n\ to some other aspect of the LDP session and the message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-3-TAGATM_BAD_RANGE 3-Error Interface [chars] Bad VPI/VCI range. Can't start a LDP session The session parameters proposed by an LDP peer differ from those\n\ preferred by the platform. The differences are not sufficient to\n\ prevent the LDP session from being established but may have an\n\ impact on label distribution operation mpls-ldp "If the parameters identified relate to the optional path vector-based\n\ loop detection mechanism note that the IETF LDP specification\n\ recommends that when Loop Detection is enabled in a portion of a\n\ network it is recommended that all LSRs in that portion of the\n\ network be configured with Loop Detection enabled and with the\n\ same path vector limit. If the parameters identified relate\n\ to some other aspect of the LDP session and the message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-3-TAGATM_BAD_RANGE 3-Error Interface [chars] Bad VPI/VCI range. Can't start a LDP session The session parameters proposed by an LDP peer differ from those\n\ preferred by the platform. The differences are not sufficient to\n\ prevent the LDP session from being established but may have an\n\ impact on label distribution operation mpls-ldp "If the parameters identified relate to the optional path vector-based\n\ loop detection mechanism note that the IETF LDP specification\n\ recommends that when Loop Detection is enabled in a portion of a\n\ network it is recommended that all LSRs in that portion of the\n\ network be configured with Loop Detection enabled and with the\n\ same path vector limit. If the parameters identified relate\n\ to some other aspect of the LDP session and the message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-3-TAGATM_NOMEM 3-Error Interface [chars] Resource failure. Can't start a LDP session An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP TAGATM VPI/VCI ranges has failed. mpls-ldp "The system will not be able to create a LDP session between\n\ the affected LDP peers. If this message persists reduce \n\ other system activity if possible and call your technical \n\ service representative for assistance." LDP-3-TAGATM_NOMEM 3-Error Interface [chars] Resource failure. Can't start a LDP session An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP TAGATM VPI/VCI ranges has failed. mpls-ldp "The system will not be able to create a LDP session between\n\ the affected LDP peers. If this message persists reduce \n\ other system activity if possible and call your technical \n\ service representative for assistance." LDP-3-TAGATM_NOMEM 3-Error Interface [chars] Resource failure. Can't start a LDP session An attempt to allocate a buffer for Label Distribution Protocol\n\ LDP TAGATM VPI/VCI ranges has failed. mpls-ldp "The system will not be able to create a LDP session between\n\ the affected LDP peers. If this message persists reduce \n\ other system activity if possible and call your technical \n\ service representative for assistance." LDP-4-ADV 4-Warning Label advertisement mode DU/DoD mismatch with peer [chars] resolved to [chars]. - mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-ADV 4-Warning Label advertisement mode DU/DoD mismatch with peer [chars] resolved to [chars]. - mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-ADV 4-Warning Label advertisement mode DU/DoD mismatch with peer [chars] resolved to [chars]. - mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-CAPCHANGE 4-Warning Reset of established LDP sessions required to propagate [chars] A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers will not learn of the change until the LDP session has\n\ been reset. mpls-ldp "Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command." LDP-4-CAPCHANGE 4-Warning Reset of established LDP sessions required to propagate [chars] A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers will not learn of the change until the LDP session has\n\ been reset. mpls-ldp "Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command." LDP-4-CAPCHANGE 4-Warning Reset of established LDP sessions required to propagate [chars] A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers will not learn of the change until the LDP session has\n\ been reset. mpls-ldp "Reset LDP neighbor using the 'clear mpls ldp neighbor ...' command." LDP-4-CAPCHANGE_DYNAMIC 4-Warning Reset of established LDP session required to propagate [chars]\n change to peers that don't support Dynamic Announcement A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers that don't support Dynamic Announcement will not learn\n\ of the changeuntil the LDP session has been reset. mpls-ldp "Use the 'show mpls ldp neighbor capability' command to determine\n\ which neighbors need to be reset. Reset LDP neighbor using the\n\ 'clear mpls ldp neighbor ...' command." LDP-4-CAPCHANGE_DYNAMIC 4-Warning Reset of established LDP session required to propagate [chars]\n change to peers that don't support Dynamic Announcement A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers that don't support Dynamic Announcement will not learn\n\ of the changeuntil the LDP session has been reset. mpls-ldp "Use the 'show mpls ldp neighbor capability' command to determine\n\ which neighbors need to be reset. Reset LDP neighbor using the\n\ 'clear mpls ldp neighbor ...' command." LDP-4-CAPCHANGE_DYNAMIC 4-Warning Reset of established LDP session required to propagate [chars]\n change to peers that don't support Dynamic Announcement A capability was installed/updated/uninstalled by an LDP client.\n\ LDP peers that don't support Dynamic Announcement will not learn\n\ of the changeuntil the LDP session has been reset. mpls-ldp "Use the 'show mpls ldp neighbor capability' command to determine\n\ which neighbors need to be reset. Reset LDP neighbor using the\n\ 'clear mpls ldp neighbor ...' command." LDP-4-MAXMSGSIZE 4-Warning Maximum implementation message size exceeded actual [dec] maximum [dec] This is an informational message that appears when LDP receives\n\ a request to allocate memory resources for an LDP message with\n\ a size exceeding the current implemented maximum. mpls-ldp "No action is required unless a larger message size is deemed to be\n\ required to support a new application. In this case the actual\n\ application should be identified and component owners contacted\n\ to increase the implemented maximum message size." LDP-4-MAXMSGSIZE 4-Warning Maximum implementation message size exceeded actual [dec] maximum [dec] This is an informational message that appears when LDP receives\n\ a request to allocate memory resources for an LDP message with\n\ a size exceeding the current implemented maximum. mpls-ldp "No action is required unless a larger message size is deemed to be\n\ required to support a new application. In this case the actual\n\ application should be identified and component owners contacted\n\ to increase the implemented maximum message size." LDP-4-MAXMSGSIZE 4-Warning Maximum implementation message size exceeded actual [dec] maximum [dec] This is an informational message that appears when LDP receives\n\ a request to allocate memory resources for an LDP message with\n\ a size exceeding the current implemented maximum. mpls-ldp "No action is required unless a larger message size is deemed to be\n\ required to support a new application. In this case the actual\n\ application should be identified and component owners contacted\n\ to increase the implemented maximum message size." LDP-4-PTCL 4-Warning peer [chars] [chars] A violation of the LDP protocol by a LDP peer has been detected. mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-PTCL 4-Warning peer [chars] [chars] A violation of the LDP protocol by a LDP peer has been detected. mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-PTCL 4-Warning peer [chars] [chars] A violation of the LDP protocol by a LDP peer has been detected. mpls-ldp ACTION_NEW_SESSION_TDP LDP-4-PWD 4-Warning MD5 protection is required for peer [chars] no password configured - mpls-ldp "This message indicates a misconfiguration on the router. If the\n\ user requires MD5 password protection for the LDP session configure\n\ a password for the LDP peer. If the user requires MD5 password\n\ protection for a subset of LDP neighbors but not for this specific\n\ LDP peer modify the LDP password configuration to exclude this LDP\n\ peer from the password required list. Otherwise if an LDP session\n\ should not exist disable MPLS to this neighbor." LDP-4-PWD 4-Warning MD5 protection is required for peer [chars] no password configured - mpls-ldp "This message indicates a misconfiguration on the router. If the\n\ user requires MD5 password protection for the LDP session configure\n\ a password for the LDP peer. If the user requires MD5 password\n\ protection for a subset of LDP neighbors but not for this specific\n\ LDP peer modify the LDP password configuration to exclude this LDP\n\ peer from the password required list. Otherwise if an LDP session\n\ should not exist disable MPLS to this neighbor." LDP-4-PWD 4-Warning MD5 protection is required for peer [chars] no password configured - mpls-ldp "This message indicates a misconfiguration on the router. If the\n\ user requires MD5 password protection for the LDP session configure\n\ a password for the LDP peer. If the user requires MD5 password\n\ protection for a subset of LDP neighbors but not for this specific\n\ LDP peer modify the LDP password configuration to exclude this LDP\n\ peer from the password required list. Otherwise if an LDP session\n\ should not exist disable MPLS to this neighbor." LDP-5-ACL 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp "No action is required." LDP-5-ACL 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp "No action is required." LDP-5-ACL 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp "No action is required." LDP-5-ACL1 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp ACTION_COPY_REPORT_TDP LDP-5-ACL1 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp ACTION_COPY_REPORT_TDP LDP-5-ACL1 5-Notice mpls ldp advertise-labels has no effect for lc-atm EXPLANATION_ACL_TDP mpls-ldp ACTION_COPY_REPORT_TDP LDP-5-CLEAR_CHKPT 5-Notice Clear [chars] checkpoint state [chars] by [chars] Checkpoint state for one or more LDP objects has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-CLEAR_CHKPT 5-Notice Clear [chars] checkpoint state [chars] by [chars] Checkpoint state for one or more LDP objects has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-CLEAR_CHKPT 5-Notice Clear [chars] checkpoint state [chars] by [chars] Checkpoint state for one or more LDP objects has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-CLEAR_NBRS 5-Notice Clear LDP neighbors [chars] by [chars] One or more LDP neighbor sessions has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-CLEAR_NBRS 5-Notice Clear LDP neighbors [chars] by [chars] One or more LDP neighbor sessions has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-CLEAR_NBRS 5-Notice Clear LDP neighbors [chars] by [chars] One or more LDP neighbor sessions has been reset mpls-ldp LOG_STD_NO_ACTION LDP-5-GR 5-Notice [chars] An informational LDP notice was generated for a Graceful Restart event. mpls-ldp LOG_STD_NO_ACTION LDP-5-GR 5-Notice [chars] An informational LDP notice was generated for a Graceful Restart event. mpls-ldp LOG_STD_NO_ACTION LDP-5-GR 5-Notice [chars] An informational LDP notice was generated for a Graceful Restart event. mpls-ldp LOG_STD_NO_ACTION LDP-5-IDENT 5-Notice cannot set [chars][chars] LDP ident - mpls-ldp "This is an informational message. As long as it needs to set\n\ its chassis LDP identifier the system will periodically\n\ attempt to do so until it succeeds. If this message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-5-IDENT 5-Notice cannot set [chars][chars] LDP ident - mpls-ldp "This is an informational message. As long as it needs to set\n\ its chassis LDP identifier the system will periodically\n\ attempt to do so until it succeeds. If this message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-5-IDENT 5-Notice cannot set [chars][chars] LDP ident - mpls-ldp "This is an informational message. As long as it needs to set\n\ its chassis LDP identifier the system will periodically\n\ attempt to do so until it succeeds. If this message occurs\n\ repeatedly copy it exactly as it appears and report it to\n\ your technical service representative." LDP-5-INFO 5-Notice [chars] This is an informational message generated by the Label\n\ Distribution Protocol LDP implementation. mpls-ldp ACTION_LOOPING_LSP LDP-5-INFO 5-Notice [chars] This is an informational message generated by the Label\n\ Distribution Protocol LDP implementation. mpls-ldp ACTION_LOOPING_LSP LDP-5-INFO 5-Notice [chars] This is an informational message generated by the Label\n\ Distribution Protocol LDP implementation. mpls-ldp ACTION_LOOPING_LSP LDP-5-NBRCHG 5-Notice [chars] Neighbor [chars] is [chars][chars] An LDP neighbor has either come up or gone down. The message\n\ describes the change for it. mpls-ldp "This informational message normally appears as routers and\n\ LDP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." LDP-5-NBRCHG 5-Notice [chars] Neighbor [chars] is [chars][chars] An LDP neighbor has either come up or gone down. The message\n\ describes the change for it. mpls-ldp "This informational message normally appears as routers and\n\ LDP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." LDP-5-NBRCHG 5-Notice [chars] Neighbor [chars] is [chars][chars] An LDP neighbor has either come up or gone down. The message\n\ describes the change for it. mpls-ldp "This informational message normally appears as routers and\n\ LDP neighbors go up or down. However unexpected neighbor loss\n\ might indicate high error rates or high packet loss in the\n\ network and should be investigated." LDP-5-PWDCFG 5-Notice Password configuration changed for [chars] An informational LDP notice was generated to report password\n\ configuration change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-PWDCFG 5-Notice Password configuration changed for [chars] An informational LDP notice was generated to report password\n\ configuration change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-PWDCFG 5-Notice Password configuration changed for [chars] An informational LDP notice was generated to report password\n\ configuration change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-PWDKEYTRUNC 5-Notice MD5 digest uses [dec] chars of longer [chars] keys for peer [chars] - mpls-ldp "This message indicates a possible misconfiguration on the router.\n\ Ensure that you have configured your key chains correctly on each\n\ router. Your LDP session can be established if the MD5 key used by\n\ the specified LDP peer has been truncated by the same amount or is\n\ defined to be equal to the truncated key value on this router." LDP-5-PWDKEYTRUNC 5-Notice MD5 digest uses [dec] chars of longer [chars] keys for peer [chars] - mpls-ldp "This message indicates a possible misconfiguration on the router.\n\ Ensure that you have configured your key chains correctly on each\n\ router. Your LDP session can be established if the MD5 key used by\n\ the specified LDP peer has been truncated by the same amount or is\n\ defined to be equal to the truncated key value on this router." LDP-5-PWDKEYTRUNC 5-Notice MD5 digest uses [dec] chars of longer [chars] keys for peer [chars] - mpls-ldp "This message indicates a possible misconfiguration on the router.\n\ Ensure that you have configured your key chains correctly on each\n\ router. Your LDP session can be established if the MD5 key used by\n\ the specified LDP peer has been truncated by the same amount or is\n\ defined to be equal to the truncated key value on this router." LDP-5-PWDRO 5-Notice Password rolled over for [chars] An informational LDP notice was generated to report lossless password\n\ change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-PWDRO 5-Notice Password rolled over for [chars] An informational LDP notice was generated to report lossless password\n\ change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-PWDRO 5-Notice Password rolled over for [chars] An informational LDP notice was generated to report lossless password\n\ change for a neighbor. mpls-ldp LOG_STD_NO_ACTION LDP-5-SP 5-Notice [chars] An informational LDP notice was generated for a Session Protection event. mpls-ldp LOG_STD_NO_ACTION LDP-5-SP 5-Notice [chars] An informational LDP notice was generated for a Session Protection event. mpls-ldp LOG_STD_NO_ACTION LDP-5-SP 5-Notice [chars] An informational LDP notice was generated for a Session Protection event. mpls-ldp LOG_STD_NO_ACTION LDP-5-UNKNOWNCAP 5-Notice Advertised Capability [chars] not supported by peer [chars] This information message is returned by peer to assist in\n\ troubleshooting interop issues that may arise when a peer is\n\ not capable of supporting an advertised LDP capability mpls-ldp LOG_STD_NO_ACTION LDP-5-UNKNOWNCAP 5-Notice Advertised Capability [chars] not supported by peer [chars] This information message is returned by peer to assist in\n\ troubleshooting interop issues that may arise when a peer is\n\ not capable of supporting an advertised LDP capability mpls-ldp LOG_STD_NO_ACTION LDP-5-UNKNOWNCAP 5-Notice Advertised Capability [chars] not supported by peer [chars] This information message is returned by peer to assist in\n\ troubleshooting interop issues that may arise when a peer is\n\ not capable of supporting an advertised LDP capability mpls-ldp LOG_STD_NO_ACTION LDPID-3-LCON 3-Error ERRMSG_NOFLAGS - - - LDPID-3-LCON 3-Error ERRMSG_NOFLAGS - - - LDPLIB-3-GENERAL 3-Error [chars] Record associated with a withdrawn label has timed out before receiving acknowledgements from all peers. mpls-ldp "This is an informational message. This will not " "have any operational impact. The system will ignore any subsequently " "received release messages associated with the label." LDPLIB-3-GENERAL 3-Error [chars] Record associated with a withdrawn label has timed out before receiving acknowledgements from all peers. mpls-ldp "This is an informational message. This will not " "have any operational impact. The system will ignore any subsequently " "received release messages associated with the label." LDPLIB-3-GENERAL 3-Error [chars] Record associated with a withdrawn label has timed out before receiving acknowledgements from all peers. mpls-ldp "This is an informational message. This will not " "have any operational impact. The system will ignore any subsequently " "received release messages associated with the label." LDPLIB-3-INIT 3-Error Cannot allocate LIB The LIB revision number used to manage advertisement of labels to LDP peers overflowed. This will result in faulty label distribution to LDP peers. The system recovers by toggling dynamic label switching off and on which forces the revision number to be re-initialized. mpls-ldp "None required." LDPLIB-3-INIT 3-Error Cannot allocate LIB The LIB revision number used to manage advertisement of labels to LDP peers overflowed. This will result in faulty label distribution to LDP peers. The system recovers by toggling dynamic label switching off and on which forces the revision number to be re-initialized. mpls-ldp "None required." LDPLIB-3-INIT 3-Error Cannot allocate LIB The LIB revision number used to manage advertisement of labels to LDP peers overflowed. This will result in faulty label distribution to LDP peers. The system recovers by toggling dynamic label switching off and on which forces the revision number to be re-initialized. mpls-ldp "None required." LES_FDDI-2-ILLEGAL 2-Critical msgtxt_fddi_illegal This error message is displayed when the router does not have\n\ enough I/O memory to support a FDDI interface. The FDDI interface\n\ requires at least 4MB of I/O memory. mid-fddi "Install the required amount of I/O memory. For maximum performance\n\ Cisco reccommends installing 8Mb of I/O memory for a single FDDI NIM\n\ and 16MB of I/O memory if 2 FDDI NIMs are installed.\n\ \n\ With 4MB of I/O memory the system will create 256 FDDI buffers for a one\n\ FDDI interface or 384 buffers for two FDDI interfaces.\n\ \n\ With 8MB of I/O memory the system will create 512 FDDI buffers for\n\ either one or two FDDI interfaces.\n\ \n\ With 16MB of I/O memory the system will create 512 FDDI buffers for\n\ a one FDDI interface or 1024 buffers for two FDDI interfaces." LEX-3-NOTSENT 3-Error Serial line down [chars] : [chars] not sent The serial line went down and the specified command was not sent to\n\ the LAN Extender. - "Determine why the serial line went down. For example was the cable\n\ was pulled or the LAN Extender powered off? The command will\n\ automatically be re-sent once the serial interface is operational." LEX-3-RCMDNAK 3-Error [chars] : [chars] could not be processed by LAN Extender The LAN Extender could not process the command from the host router.\n\ Possible causes are:\n\\n\ The LAN Extender ran out of memory.\n\\n\ The message from the host router is malformed.\n\\n\ A request to write flash occurred while the LAN Extender was busy\n\ writing flash for a previous request.\n\\n\ The size of a file to be downloaded is greater than the amount of flash\n\ memory available. - "If the command was copy tftp lex unit-number or copy flash lex\n\ unit-number make sure that the correct file that is a FLEX image\n\ file is specified. Only a single copy request can be handled at one\n\ time. If the problem was caused by a temporary out-of-memory condition\n\ on the LAN Extender re-enter the command." LEX-3-RCMDREJ 3-Error [chars] : [chars] could not be processed by LAN Extender The LAN Extender did not recognize the code for the specified remote\n\ command. This might occur if the user is running old LAN Extender\n\ software with newer host router software that has support for new LEX\n\ remote commands. - "Update the LAN Extender software." LEX-3-TIMEOUT 3-Error Retry count exceeded for [chars] : [chars] The host router re-sent the given message as many times as specified\n\ in the lex retry-count command configuration variable without\n\ receiving an acknowledgment from the LAN Extender. At this point the\n\ host router gives up trying to send this particular remote command\n\ message. - "Use the LEDs on the LAN Extender to determine if it is operational.\n\ Confirm that the lex timeout configuration command is set appropriately\n\ for the speed of the link." LFD-2-AVL 2-Critical [chars] [hec] AVL tree operation error mpls-mfi LOG_STD_ACTION LFD-2-AVL 2-Critical [chars] [hec] AVL tree operation error mpls-mfi LOG_STD_ACTION LFD-2-FPIHANDLER3 2-Critical [chars] [hec] [hec] [hec] FPI Handler error mpls-mfi LOG_STD_ACTION LFD-2-FPIHANDLER3 2-Critical [chars] [hec] [hec] [hec] FPI Handler error mpls-mfi LOG_STD_ACTION LFD-3-BADEXEC 3-Error Unexpected Code Execution: [chars] [dec] Unexpected Code Execution mpls-mfi LOG_STD_ACTION LFD-3-BADEXEC 3-Error Unexpected Code Execution: [chars] [dec] Unexpected Code Execution mpls-mfi LOG_STD_ACTION LFD-3-BADFRRTYPE 3-Error illegal frr type: [dec] FRR request type error mpls-mfi LOG_STD_ACTION LFD-3-BADFRRTYPE 3-Error illegal frr type: [dec] FRR request type error mpls-mfi LOG_STD_ACTION LFD-3-BADLABELADD 3-Error Cannot add label - [chars]. Unable to create label due to reason given. mpls-mfi LOG_STD_ACTION LFD-3-BADLABELADD 3-Error Cannot add label - [chars]. Unable to create label due to reason given. mpls-mfi LOG_STD_ACTION LFD-3-BADSHORTLABELADD 3-Error Cannot add short label: path_idx [dec] moi_type [dec] Unable to create MFI feature space in FIB entry so unable to store short path extension information there. mpls-mfi LOG_STD_ACTION LFD-3-BADSHORTLABELADD 3-Error Cannot add short label: path_idx [dec] moi_type [dec] Unable to create MFI feature space in FIB entry so unable to store short path extension information there. mpls-mfi LOG_STD_ACTION LFD-3-BROKERINITFAIL 3-Error Failed to initialise lte RP broker facility An internal software error occurred. mpls-mfi LOG_STD_ACTION LFD-3-BROKERINITFAIL 3-Error Failed to initialise lte RP broker facility An internal software error occurred. mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGR 3-Error chunk mgr: [chars] 0x[hec] Chunk manager error mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGR 3-Error chunk mgr: [chars] 0x[hec] Chunk manager error mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGRALLOC 3-Error failed chunk alloc: [chars] Chunk alloc failed mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGRALLOC 3-Error failed chunk alloc: [chars] Chunk alloc failed mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGRDEALLOC 3-Error failed chunk dealloc: [chars] Chunk free failed mpls-mfi LOG_STD_ACTION LFD-3-CHUNKMGRDEALLOC 3-Error failed chunk dealloc: [chars] Chunk free failed mpls-mfi LOG_STD_ACTION LFD-3-CORRUPTED_PKT 3-Error [chars] lfd received corrupted packet mpls-mfi LOG_STD_ACTION LFD-3-CORRUPTED_PKT 3-Error [chars] lfd received corrupted packet mpls-mfi LOG_STD_ACTION LFD-3-EVTLOGBADSOURCE 3-Error Illegal log event source: [dec] Illegal event found in log buffer mpls-mfi LOG_STD_ACTION LFD-3-EVTLOGBADSOURCE 3-Error Illegal log event source: [dec] Illegal event found in log buffer mpls-mfi LOG_STD_ACTION LFD-3-FIB_SRC 3-Error Label [[dec]/[dec]] [chars] [chars] [chars] The fib entry could not be sourced for label in question. mpls-mfi "If there is no matching bug for this problem " "please collect the output of " "show mpls forwarding-table internal and " "show ip route [vrf ] and " "the error message traceback and file a bug" LFD-3-FIB_SRC 3-Error Label [[dec]/[dec]] [chars] [chars] [chars] The fib entry could not be sourced for label in question. mpls-mfi "If there is no matching bug for this problem " "please collect the output of " "show mpls forwarding-table internal and " "show ip route [vrf ] and " "the error message traceback and file a bug" LFD-3-FIBIPINVALID 3-Error [chars] table: [dec] label: [dec] IP path information is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FIBIPINVALID 3-Error [chars] table: [dec] label: [dec] IP path information is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FIBIPINVALIDAF 3-Error AF: [dec] [chars] table: [dec] label: [dec] IP path information AF is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FIBIPINVALIDAF 3-Error AF: [dec] [chars] table: [dec] label: [dec] IP path information AF is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FIBNONIPINVALID 3-Error [chars] table: [dec] label: [dec] Non IP path information is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FIBNONIPINVALID 3-Error [chars] table: [dec] label: [dec] Non IP path information is invalid for the indicated label table entry mpls-mfi LOG_STD_SH_TECH_ACTION LFD-3-FPIHANDLER 3-Error LFD SSS Handler: [chars] Error in fpi handler mpls-mfi LOG_STD_ACTION LFD-3-FPIHANDLER 3-Error LFD SSS Handler: [chars] Error in fpi handler mpls-mfi LOG_STD_ACTION LFD-3-FPITYPEWRONG 3-Error Require fpi type [chars] get fpi type [chars] Unmatched FPI type mpls-mfi LOG_STD_ACTION LFD-3-FPITYPEWRONG 3-Error Require fpi type [chars] get fpi type [chars] Unmatched FPI type mpls-mfi LOG_STD_ACTION LFD-3-INTFDB 3-Error intf db: [chars] [hec] Interface db error mpls-mfi LOG_STD_ACTION LFD-3-INTFDB 3-Error intf db: [chars] [hec] Interface db error mpls-mfi LOG_STD_ACTION LFD-3-INTFDB2 3-Error intf db: [chars] [hec] [hec] Interface db error mpls-mfi LOG_STD_ACTION LFD-3-INTFDB2 3-Error intf db: [chars] [hec] [hec] Interface db error mpls-mfi LOG_STD_ACTION LFD-3-INVIPLABELTYPE 3-Error Wrong label type [dec] for IP Label [dec] table [dec] prefix [chars] vrf [chars] Label type is invalid for the indicated label table entry mpls-mfi "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of" " show version " "and show running-config and" "contact your Cisco technical support representative." LFD-3-INVIPLABELTYPE 3-Error Wrong label type [dec] for IP Label [dec] table [dec] prefix [chars] vrf [chars] Label type is invalid for the indicated label table entry mpls-mfi "Refer to the Bug Navigator at www.cisco.com to see if this " "condition has been previously reported and resolved in a " "later release. If not gather the output of" " show version " "and show running-config and" "contact your Cisco technical support representative." LFD-3-INVLABELTYPE 3-Error Wrong label type [dec] for non-ip LTE [dec]/[dec] Label type invalid for non-ip label table entry mpls-mfi LOG_STD_ACTION LFD-3-INVLABELTYPE 3-Error Wrong label type [dec] for non-ip LTE [dec]/[dec] Label type invalid for non-ip label table entry mpls-mfi LOG_STD_ACTION LFD-3-INVLABELUPDTYPE 3-Error Wrong label type [dec] for label [dec] table [dec] [chars] [chars] An invalid Label type was encountered during the specified operation mpls-mfi "If there is no matching bug for this problem " "please collect the output of show mpls" " forwarding-table label